TI1 LM53635MQRNLRQ1 Step-down dc-dc converter Datasheet

Product
Folder
Sample &
Buy
Technical
Documents
Support &
Community
Tools &
Software
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
LM53625/35-Q1, 2.5-A or 3.5-A, 36-V Synchronous, 2.1-MHz, Step-Down DC-DC Converter
1 Features
3 Description
•
The LM53625-Q1/LM53635-Q1 synchronous buck
regulator is optimized for automotive applications,
providing an output voltage of 5 V, 3.3 V, or an
adjustable output. Advanced high-speed circuitry
allows the LM53625-Q1/LM53635-Q1 to regulate
from an input of 18 V to an output of 3.3 V at a fixed
frequency of 2.1 MHz. Innovative architecture allows
this device to regulate a 3.3-V output from an input
voltage of only 3.55 V. All aspects of the LM53625Q1/LM53635-Q1 are optimized for automotive and
performance-driven industrial customers. An input
voltage range up to 36 V, with transient tolerance up
to 42 V, eases input surge protection design. The
automotive-qualified Hotrod QFN package with
wettable flanks reduces parasitic inductance and
resistance while increasing efficiency, minimizing
switch node ringing, and dramatically lowering
electromagnetic interference (EMI). An open-drain
reset output, with built-in filtering and delay, provides
a true indication of system status. This feature
negates the requirement for an additional supervisory
component, saving cost and board space. Seamless
transition between PWM and PFM modes and low
quiescent current (only 15 µA for the 3.3 V option)
ensure high efficiency and superior transient
responses at all loads.
1
•
•
•
•
•
•
•
•
•
•
•
•
AEC-Q100 Automotive Qualified:
– Device Temperature Grade 1: –40°C to
+125°C Ambient Operating Temperature
Range
– Device HBM Classification Level 2
– Device CDM Classification Level C6
–40°C to +150°C Junction Temperature Range
15-µA Quiescent Current at no Load (Typical) with
3.3-V Output
4 mm × 5 mm, 0.5-mm Pitch VQFN Package With
Wettable Flanks and 0.6-mm VIN Spacing
Low EMI and Switch Noise
Spread Spectrum Option
External Frequency Synchronization
RESET Output with Internal Filter and 3-ms
Release Timer
Pin-Selectable Forced PWM Mode
Built-In Compensation, Soft Start, Current Limit,
Thermal Shutdown, and UVLO
0.6-V Dropout at 3.5 A at 105°C TA
±1% Output Voltage Tolerance (–40°C to 125°C
TJ)
Available With Fixed 5-V, 3.3-V or Adjustable
Output
Device Information(1)
DEVICE NAME
LM53625-Q1
PACKAGE
VQFN-HR (22)
BODY SIZE
5.00 mm × 4.00 mm
2 Applications
LM53635-Q1
•
•
•
•
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Automotive Telematics
Navigation Systems
In-Dash Instrumentation
Battery-Powered Applications
Typical Application Circuit
Typical Automotive Layout (22 mm x 12.5 mm)
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Device Comparison ...............................................
Pin Configuration and Functions .........................
Specifications.........................................................
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
8
1
1
1
2
3
4
5
Absolute Maximum Ratings ...................................... 5
ESD Ratings ............................................................ 5
Recommended Operating Conditions....................... 6
Thermal Information .................................................. 6
Electrical Characteristics........................................... 7
System Characteristics ............................................. 9
Timing Characteristics............................................... 9
Typical Characteristics ............................................ 10
Detailed Description ............................................ 12
8.1 Overview ................................................................. 12
8.2 Functional Block Diagram ....................................... 13
8.3 Feature Description................................................. 14
8.4 Device Functional Modes........................................ 19
8.5 Spread-Spectrum Operation ................................... 22
9
Application and Implementation ........................ 23
9.1 Application Information............................................ 23
9.2 Typical Applications ................................................ 23
9.3 Do's and Don't's ...................................................... 41
10 Power Supply Recommendations ..................... 41
11 Layout................................................................... 42
11.1 Layout Guidelines ................................................. 42
11.2 Layout Example .................................................... 43
12 Device and Documentation Support ................. 45
12.1
12.2
12.3
12.4
12.5
12.6
12.7
Device Support......................................................
Documentation Support ........................................
Related Links ........................................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
45
45
45
46
46
46
46
13 Mechanical, Packaging, and Orderable
Information ........................................................... 46
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Original (December 2015) to Revision A
•
2
Page
Product Preview to Production Data ..................................................................................................................................... 1
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
5 Device Comparison
Table 1. LM53625-Q1 Devices (2.5-A Output)
PART NUMBER
OUTPUT VOLTAGE
SPREAD
SPECTRUM
PACKAGE QTY
LM53625AQRNLRQ1
Adjustable
No
3000
LM53625AQRNLTQ1
Adjustable
No
250
LM536253QRNLRQ1
3.3 V
No
3000
LM536253QRNLTQ1
3.3 V
No
250
LM536255QRNLRQ1
5V
No
3000
LM536255QRNLTQ1
5V
No
250
LM53625MQRNLRQ1
Adjustable
Yes
3000
LM53625MQRNLTQ1
Adjustable
Yes
250
LM53625NQRNLRQ1
3.3 V
Yes
3000
LM53625NQRNLTQ1
3.3 V
Yes
250
LM53625LQRNLRQ1
5V
Yes
3000
LM53625LQRNLTQ1
5V
Yes
250
Table 2. LM53635-Q1 Devices (3.5-A Output)
PART NUMBER
OUTPUT VOLTAGE
SPREAD
SPECTRUM
PACKAGE QTY
LM53635AQRNLRQ1
Adjustable
No
3000
LM53635AQRNLTQ1
Adjustable
No
250
LM536353QRNLRQ1
3.3 V
No
3000
LM536353QRNLTQ1
3.3 V
No
250
LM536355QRNLRQ1
5V
No
3000
LM536355QRNLTQ1
5V
No
250
LM53635MQRNLRQ1
Adjustable
Yes
3000
LM53635MQRNLTQ1
Adjustable
Yes
250
LM53635NQRNLRQ1
3.3 V
Yes
3000
LM53635NQRNLTQ1
3.3 V
Yes
250
LM53635LQRNLRQ1
5V
Yes
3000
LM53635LQRNLTQ1
5V
Yes
250
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
3
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
6 Pin Configuration and Functions
RNL Package
22-Pin VQFN
Top View
PGND1
PGND2
PGND2
PGND2
PGND1
PGND1
SW
PGND1
PGND2
PVIN 2
PVIN 1
AVIN
SYNC
FPWM
CBOOT
NC
VCC
EN
RESET AGND
FB
BIAS
Pin Functions
PIN
NO.
NAME
I/O (1)
DESCRIPTION
1
VCC
A
Internal 3.1-V LDO output. Used as supply to internal control circuits. Connect a high-quality
4.7-µF capacitor from this pin to AGND.
2
CBOOT
P
Bootstrap capacitor connection for gate drivers. Connect a high quality 470-nF capacitor from
this pin to the SW pin.
3
SYNC
I
Synchronization input to regulator. Used to synchronize the device switching frequency to a
system clock. Triggers on rising edge of external clock; frequency must be in the range of
1.9 MHz and 2.3 MHz.
4
PVIN1
P
Input supply to regulator. Connect input bypass capacitors directly to this pin and PGND
pins. Connect PVIN1 and PVIN2 pins directly together at PCB.
5, 6, 7, 8
PGND1
G
Power ground to internal low side MOSFET. These pins must be tied together on the PCB.
Connect PGND1 and PGND2 directly together at PCB. Connect to AGND and system
ground.
SW
P
Regulator switch node. Connect to power inductor.
10, 11, 12, 13
PGND2
G
Power ground to internal low side MOSFET. These pins must be tied together. Connect
PGND1 and PGND2 directly together at PCB. Connect to AGND and system ground.
14
PVIN2
P
Input supply to regulator. Connect input bypass capacitors directly to this pin and PGND
pins. Connect PVIN1 and PVIN2 pins directly together at PCB.
15
AVIN
A
Analog VIN, Connect to PVIN1 and PVIN2 on PCB.
16
FPWM
I
Do not float. Mode control input of regulator. High = FPWM, low = Automatic light load mode.
17
NC
—
18
EN
I
Enable input to regulator. High = on, Low = off. Can be connected to VIN. Do not float.
19
RESET
O
Open drain reset output flag. Connect to suitable voltage supply through a current limiting
resistor. High = regulator OK, Low = regulator fault. Goes low when EN = low.
20
AGND
G
Analog ground for regulator and system. All electrical parameters are measured with respect
to this pin. Connect to PGND on PCB
21
FB
A
Feedback input to regulator. Connect to output voltage node for fixed VOUT options.
Connect to feedback voltage divider for adjustable option.
22
BIAS
P
Input to auxiliary bias regulator. Connect to output voltage node.
9
(1)
4
No internal connection
A = Analog, O = Output, I = Input, G = Ground, P = Power
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
7 Specifications
7.1 Absolute Maximum Ratings
over the recommended operating junction temperature range of –40°C to +150°C (unless otherwise noted) (1)
PARAMETER
VIN (AVIN,PVIN1 and PVIN2) to AGND, PGND1 and PGND2 (2)
SW to AGND, PGND
(3)
MIN
MAX
UNIT
–0.3
40
V
–0.3
VIN + 0.3
V
CBOOT to SW
–0.3
3.6
V
EN to AGND, PGND (2) (4)
–0.3
40
V
BIAS to AGND, PGND
–0.3
16
V
FB to AGND, PGND
–0.3
16
V
RESET to AGND, PGND
–0.3
8
V
RESET sink current
(5)
10
mA
SYNC to AGND,PGND (2) (4)
–0.3
40
V
FPWM to AGND,PGND (4)
–0.3
40
V
VCC to AGND,PGND
–0.3
3.6
V
Junction temperature
–40
150
°C
Storage temperature, Tstg
–40
150
°C
(1)
(2)
(3)
(4)
(5)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions are not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
A maximum of 42 V can be sustained at this pin for a duration of ≤ 500 ms at a duty cycle of ≤ 0.01%.
A voltage of 2 V below PGND and 2 V above VIN can appear on this pin for ≤ 200 ns with a duty cycle of ≤ 0.01%.
Under no conditions should the voltage on this pin be allowed to exceed the voltage on the PVIN1,PVIN2 or AVIN pins by more than 0.3
V.
Do not exceed the voltage rating on this pin.
7.2 ESD Ratings
VALUE
V(ESD)
(1)
Electrostatic discharge
Human-body model (HBM), per AEC Q100-002 (1)
±2500
Charged-device model (CDM), per AEC Q100-011
±1000
UNIT
V
AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
5
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
7.3 Recommended Operating Conditions
over the recommended operating junction temperature range of –40°C to +150°C (unless otherwise noted)
MIN
Input voltage after start-up
(1)
NOM
MAX
3.9
UNIT
36
V
Output voltage for 3.3-V LM53625/35-Q1 (2)
3.4
V
Output voltage for 5-V LM53625/35-Q1 (2)
5.2
V
10
V
Load current for LM53625-Q1, fixed output option and adjustable
2.5
A
Load current for LM53635-Q1, fixed output option and adjustable
3.5
A
Output adjustment for adjustable version of LM53625/35-Q1 (2)
3.3
Junction temperature for 1000-hour lifetime
–40
125
°C
Junction temperature for 408-hour lifetime
–40
150
°C
(1)
(2)
An extended input voltage range to 3.5 V is possible; see System Characteristics table. See Input UVLO for start-up conditions.
The output voltage must not be allowed to fall below zero volts during normal operation.
7.4 Thermal Information
LM53625/35-Q1
THERMAL METRIC (1)
RNL (VQFN)
UNIT
22 PINS
RθJA
Junction-to-ambient thermal resistance
29.4
°C/W
RθJC
Junction-to-case (top) thermal resistance
14.2
°C/W
RθJB
Junction-to-board thermal resistance
5.4
°C/W
ψJT
Junction-to-top characterization parameter
1.2
°C/W
ψJB
Junction-to-board characterization parameter
5.4
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
2.4
°C/W
(1)
6
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
7.5 Electrical Characteristics
Limits apply over the recommended operating junction temperature range of –40°C to +150°C, unless otherwise noted.
Minimum and maximum limits are specified through test, design, or statistical correlation. Typical values represent the most
likely parametric norm at Tj = 25°C, and are provided for reference purposes only. Unless otherwise stated the following
conditions apply: VIN = 13.5 V.
PARAMETER
TEST CONDITIONS
VFB
Initial output voltage accuracy
IQ
Operating quiescent current;
measured at VIN pin when
enabled and not switching (1)
IB
Bias current into BIAS pin,
enabled, not switching
VIN = 3.8 V to 36 V, TJ = 25°C
VIN = 3.8 V to 36 V
MIN
–1%
1%
1.5%
VIN = 13.5 V, VBIAS = 5 V, TJ = 85°C
Minimum input voltage to operate
35
VIN = 13.5 V, VBIAS = 3.3 V, FPWM
=0V
35
µA
VRESET
3
EN ≤ 0.4V, TJ = 150°C
5
Rising
3.2
3.55
3.95
Falling
2.95
3.25
3.55
Rising, % of VOUT
RESET lower threshold voltage
Falling, % VOUT
Magnitude of RESET lower
threshold from steady state
output voltage
Steady-state output voltage and
RESET threshold read at the same
TJ and VIN
VRESET_HYST
RESET hysteresis as a percent of
output voltage setpoint
VRESET_VALID
Minimum input voltage for proper
RESET function
Low level RESET function output
voltage
VOL
FSW
Switching frequency
FSYNC
Sync frequency range
DSYNC
Sync input duty cycle range
VFPWM
FPWM input threshold voltage
FSSS
Frequency span of spread
spectrum operation
FPSS
Spread-spectrum pattern
frequency (2)
FSW-SS
Switching Frequency while in
spread spectrum
(2)
0.28
0.3
0.4
105%
107%
110%
92%
94%
96.5%
µA
V
96%
±1
50-µA pullup to RESET pin, EN = 0
V, TJ= 25°C
1.5
50-µA pullup to RESET pin, VIN =1.5
V, EN = 0 V
0.4
0.5-mA pullup to RESET pin, VIN
=13.5 V, EN=0 V
0.4
1-mA pullup to RESET pin, VIN
=13.5 V, EN=3.3 V
0.4
VIN = 13.5 V, center frequency with
spread spectrum, PWM operation
1.85
2.1
2.35
VIN = 13.5 V, without spread
spectrum, PWM operation
1.85
2.1
2.35
1.9
2.1
2.3
V
V
MHz
High state input < 5.5 V and > 2.3 V
25%
FPWM input high (MODE = FPWM)
1.5
MHz
75%
FPWM input low (MODE = AUTO
with diode emulation)
FPWM input hysteresis
(1)
2
EN ≤ 0.4 V, TJ = 85°C
Hysteresis
µA
16
VIN = 13.5 V, VBIAS = 5 V, FPWM =
0V
RESET upper threshold voltage
UNIT
6
EN ≤ 0.4 V, TJ = 25°C
VIN-OPERATE
MAX
–1.5%
VIN = 13.5 V, VBIAS = 5 V
Shutdown quiescent current;
measured at VIN pin
ISD
TYP
0.4
0.15
V
1
±3%
9
VIN = 13.5 V, PWM operation
1.81
Hz
MHz
This is the current used by the device while not switching, open loop on the ATE. It does not represent the total input current from the
regulator system.
Ensured by Design, Not tested at production.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
7
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
Electrical Characteristics (continued)
Limits apply over the recommended operating junction temperature range of –40°C to +150°C, unless otherwise noted.
Minimum and maximum limits are specified through test, design, or statistical correlation. Typical values represent the most
likely parametric norm at Tj = 25°C, and are provided for reference purposes only. Unless otherwise stated the following
conditions apply: VIN = 13.5 V.
PARAMETER
TEST CONDITIONS
IFPWM
FPWM leakage current
ISYNC
SYNC leakage current
IL-HS
High-side switch current limit
IL-LS
Low-side switch current limit
IL-ZC
Zero-cross current limit FPWM =
low
IL-NEG
Negative current limit FPWM =
high
RDSON
Power switch on-resistance
VEN
Enable input threshold voltage rising
VEN_HYST
Enable threshold hysteresis
VEN_WAKE
Enable wake-up threshold
IEN
EN pin input current
MIN
TYP
VIN = 13.5 V, VFPWM = 3.3 V
1
VIN = VFPWM = 13.5 V
5
VIN = 13.5 V, VSYNC = 3.3 V
1
VIN = VSYNC = 13.5 V
5
MAX
UNIT
µA
µA
LM53625
3.5
5
6.5
LM53635
4.5
6
7.5
LM53625
2.5
3.5
4.1
LM53635
3.5
4.5
5.1
A
A
–0.02
A
–1.5
High-side MOSFET RDSON, VIN = 13
V, IL=1A
60
130
Low-side MOSFET RDSON, VIN = 13
V, IL=1A
40
80
mΩ
Enable rising
1.7
2
V
0.45
0.55
V
0.4
VIN = VEN = 13.5 V
V
2
VIN 13.5 V, VBIAS = 0 V
3.05
VIN = 13.5 V, VBIAS = 3.3 V
3.15
5
µA
VCC
Internal VCC voltage
VCC_UVLO
Internal VCC input undervoltage
lockout
VIN rising
2.7
V
Hysteresis below VCC-UVLO
185
mV
IFB
Input current from FB to AGND
Adjustable LM53625/35-Q1, FB=1 V
20
TJ = 25°C
VREF
RRESET
Reference voltage for adjustable
option only
1
TJ = –40°C to 125°C
0.99
1
1.01
TJ = –40°C to 150°C
0.985
1
1.015
50
85
Ω
0.4
V
VIH
VSYNC
0.15
TSD
Thermal shutdown thresholds (2)
DMAX
Maximum switch duty cycle
Submit Documentation Feedback
1.007
V
1.5
VIL
VHYST
8
nA
0.993
Pull FB pin low. Sink 1-mA at
RESET pin
RDSON of RESEToutput
V
Rising
155
Hysteresis
175
15
Fsw = 2.1 MHz
While in dropout
1
°C
80%
(2)
98%
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
7.6 System Characteristics
The following specifications are ensured by design provided that the component values in the typical application circuit are
used. These parameters are not ensured by production testing. Limits apply over the recommended operating junction
temperature range of –40°C to +150°C, unless otherwise noted. Minimum and maximum limits are specified through test,
design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for
reference purposes only. Unless otherwise stated the following conditions apply: VIN = 13.5 V.
PARAMETER
VIN-MIN
VOUT
IQ-VIN
TEST CONDITIONS
MIN
TYP
MAX
Minimum input voltage for full
functionality at 1.5 A load, after startup.
VOUT = 3.3 V +2/–3% regulation
Minimum input voltage for full
functionality at maximum rated load
3.5 A after start-up.
VOUT = 3.3 V +2/–3% regulation
Output voltage for 5-V option
VIN = 5.6 V to 36 V, IOUT = 3.5 A
4.925
5
5.08
Output voltage for 3.3-V option
VIN 3.9 V to 36 V, IOUT = 3.5 A
3.24
3.3
3.35
Output voltage for 5-V option
VIN = 5.5 V to 36 V, IOUT = 100 µA to 100
mA
4.92
5.05
5.125
Output voltage for 3.3-V option
VIN = 3.8 V to 36 V, IOUT = 100 µA to 100
mA
3.24
3.33
3.38
Output voltage for adjustable option
VIN = VOUT + 1 V to 36 V, IOUT = 3.5 A
Input current to VIN pin
UNIT
3.5
V
3.9
–2.25%
2.25%
VIN= 13.5 V, VOUT = 3.3 V, IOUT = 0 A
FPWM = 0
15
VIN = 13.5 V, VOUT = 5.0 V and IOUT = 0 A
FPWM = 0
20
VDROP1
Minimum input to output voltage
differential to maintain regulation
accuracy without inductor DCR drop
VOUT = 3.3 V/5 V, IOUT= 3.5 A, +2/–3%
output accuracy
VDROP2
Minimum input to output voltage
differential to maintain FSW ≥ 1.85
MHz without inductor DCR drop
VOUT = 3.3 V/5 V, IOUT=3.5 A, FSW = 1.85
MHz, 2% regulation accuracy
Efficiency
Typical Efficiency without inductor
loss
V
40
µA
0.35
0.6
V
1.1
1.4
V
VIN = 13.5 V, VOUT= 5.0 V, IOUT = 3.5 A
90%
VIN = 13.5 V, VOUT = 3.3 V, IOUT = 3.5 A
84%
VIN = 13.5 V, VOUT = 5 V, IOUT = 100 mA
88%
7.7 Timing Characteristics
Limits apply over the recommended operating junction temperature range of –40°C to +150°C, unless otherwise noted.
Minimum and maximum limits are ensured through test, design or statistical correlation. Typical values represent the most
likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless otherwise stated the following
conditions apply: VIN = 13.5 V.
NOM
MAX
tON
Minimum switch on time, VIN = 18 V, IL=1 A
MIN
65
84
ns
tOFF
Minimum switch off time, VIN = 3.8 V, IL=1 A
60
80
ns
tRESET-act
Delay time to RESET high signal
ms
tRESET-filter
Glitch filter time for RESET function (1)
tSS
Soft-Start Time from first switching pulse to VREF at 90%
tEN
Turn-on delay, CVCC = 2.2 µF (2)
1
ms
tW
Short circuit wait time (hiccup time) (3)
6
ms
Change transition time from AUTO to FPWM MODE, 20-mA load,
VIN = 13.5 V
100
µs
Change transition time from FPWM to AUTO MODE, 20-mA load,
VIN = 13.5 V
80
µs
tFPWM
(1)
(2)
(3)
UNIT
2
3
4
12
25
45
µs
2
3.2
5
ms
See Detailed Description.
This is the time from the rising edge of EN to the time that the soft-start ramp begins.
Tw is the wait time between current limit trip and re-start. Tw is nominally 4× the soft-start time. However, provision must be made to
make Tw longer to ensure survivability during an output short circuit.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
9
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
7.8 Typical Characteristics
Unless otherwise specified the following conditions apply: VIN = 12 V, TA = 25ºC. Specified temperatures are ambient.
100.2%
2.2
100.1%
2.175
Switching Frequency (MHz)
Reference Voltage Drift
100%
99.9%
99.8%
99.7%
99.6%
99.5%
99.4%
2.15
2.125
2.1
2.075
2.05
2.025
99.3%
99.2%
-40
-20
0
20
40
60
80 100
Temperature (qC)
120
140
2
-50
160
VIN = 12 V
Figure 1. Reference Voltage Drift
100
125
150
D023
Figure 2. Switching Frequency vs Temperature
LM53635
LM53625
4.6
6
5.8
4.4
Current (A)
5.6
Current (A)
25
50
75
Temperature (qC)
4.8
6.2
5.4
5.2
5
4.8
4.6
4.2
4
3.8
3.6
4.4
LM53635
LM53625
4.2
4
-40
-20
0
20
40
60
80 100
Temperature (qC)
120
140
3.4
3.2
-40
160
-20
0
20
D034
VIN = 12 V
40
60
80 100
Temperature (qC)
120
140
160
D035
VIN = 12V
Figure 3. High Side/Peak Current Limit for LM53625/35-Q1
0.065
0.06
0.055
0.05
0.045
0.04
0.035
0.03
0.025
0.02
0.015
0.01
0.005
0
Figure 4. Low Side/Valley Current Limit for LM53625/35-Q1
14
5 Vin
8 Vin
12 Vin
13.5 Vin
18 Vin
36 Vin
12
10
Current (PA)
Input Current (A)
0
VIN = 12 V
6.4
8
6
4
2
0
5
10
15
20
25
Input Voltage (V)
30
35
VIN = 12 V
Submit Documentation Feedback
40
0
-40
-20
0
20
D004
40
60
80 100
Temperature (qC)
120
140
160
D028
VIN = 12 V
Figure 5. Short Circuit Average Input Current
for LM53635-Q1
10
-25
D024
Figure 6. Shutdown Current
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
Typical Characteristics (continued)
Unless otherwise specified the following conditions apply: VIN = 12 V, TA = 25ºC. Specified temperatures are ambient.
5.4
108%
VRESET_UPPER
VRESET_UPPER
5.3
VRESET_UPPER_FALLING
% of Vout at no load
5.2
106%
Voltage (V)
5.1
VOUT
5
4.9
4.8
4.7
VRESET_LOWER_RISING
102%
100%
98%
VRESET_LOWER
96%
4.6
4.5
-40
104%
-20
0
20
40
60
80 100
Termperature (qC)
120
140
Figure 7. RESET Threshold Fixed 5-V output
160
94%
-40
VRESET_LOWER
-20
0
D026
20
40
60
80 100
Temperature (qC)
120
140
160
D027
Figure 8. RESET Threshold as Percentage of Output Voltage
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
11
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
8 Detailed Description
8.1 Overview
The LM53625/35-Q1 is a wide input voltage range, low quiescent current, high performance regulator with
internal compensation designed specifically for the automotive market. This device is designed to minimize endproduct cost and size while operating in demanding automotive environments. Normal operating frequency is 2.1
MHz allowing the use of small passive components. Because the operating frequency is above the AM band,
significant saving in input filtering is also achieved. This device has a low unloaded current consumption
eliminating the need for an external back-up LDO. The LM53625/35-Q1 low shutdown current and high maximum
operating voltage also allows the elimination of an external load switch. To further reduce system cost, an
advanced reset output is provided, which can often eliminate the use of an external reset device.
The LM53625/35-Q1 is designed with a flip-chip or HotRod technology, greatly reducing the parasitic inductance
of pins. In addition, the layout of the device allows for reduction in the radiated noise generated by the switching
action through partial cancellation of the current generated magnetic field.
As a result the switch-node waveform exhibits less overshoot and ringing.
Figure 9. Switch Node Waveform (VIN=13.5V, IOUT=3.5A)
The LM53625/35-Q1 is AEC-Q1 qualified as well as having electrical characteristics ensured up to a maximum
junction temperature of 150°C.
The LM53625/35-Q1 is available in VQFN package with wettable-flanks which allows easy inspection of the
soldering job without the requirement of X-ray checks.
Please note that, throughout this data sheet, references to the LM53625 apply equally to the LM53635. The
difference between the two devices is the maximum output current and specified MOSFET current limits.
12
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
8.2 Functional Block Diagram
SYNC
VIN
VCC BIAS
* = Not used in -ADJ
INT. REG.
BIAS
OSCILLATOR
ENABLE
LOGIC
EN
CBOOT
HS CURRENT
SENSE
1.0 V
Reference
FB
ERROR
AMPLIFIER
*
+
-
+
-
PWM
COMP.
CONTROL
LOGIC
SW
DRIVER
*
LS CURRENT
SENSE
RESET
MODE
LOGIC
RESET
CONTROL
FPWM
AGND
PGND
Copyright © 2016, Texas Instruments Incorporated
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
13
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
Functional Block Diagram (continued)
8.2.1 Control Scheme
The LM53625/35-Q1 control scheme allows this device to operate under a wide range of conditions with a low
number of external components. Peak current mode control allows a wide range of input voltages and output
capacitance values, while maintaining a constant switching frequency. Stable operation is maintained while
output capacitance is changed during operation as well. This allows use in systems that require high
performance during load transients and which have load switches that remove loads as system operating state
changes. Short minimum on and off times ensure constant frequency regulation over a wide range of conversion
ratios. These on and off times allow for a duty factor window of 13% to 87% at 2.1-MHz switching frequency.
This architecture uses frequency spreading in order to achieve low dropout voltage maintaining output regulation
as the input voltage falls close to output voltage. The frequency spreading is smooth and continuous, and
activated as off time approaches its minimum. Under these conditions, the LM53625/35-Q1 operates much like a
constant off-time converter allowing the maximum duty cycle to reach 98% and output voltage regulation with
300-mV dropout at 3.5 A.
While input voltage is high enough to require duty factor below 13%, frequency is reduced smoothly to allow
lower duty factors. In this mode many of the beneficial properties of current-mode control such as insensitivity to
output capacitance is maintained. The LM53625/35-Q1 has short enough minimum on time to maintain 2.1-MHz
operation while converting a 18 V input to a 3.3-V output.
As load current is reduced, the LM53625/35-Q1 transitions to light load mode. In this mode, diode emulation is
used to reduce RMS inductor current and switching frequency is reduced. Also, fixed voltage versions do not
need a voltage divider connected to FB saving additional power. As a result, only 15 µA (typical, while converting
13.5 V to 3.3 V) is consumed to regulate output voltage if output is unloaded. Average output voltage increases
slightly while lightly loaded as well.
For applications that require constant operating frequency regardless of the load condition, the FPWM pin allows
the user to disable the light load operating mode. The device then switches at 2.1 MHz regardless of the output
current. Diode emulation is also turned off when the FPWM pin is set high.
8.3 Feature Description
8.3.1 RESET Flag Output
The RESET function, built into the LM53625/35-Q1, has special features not found in the ordinary Power-Good
function. A glitch filter prevents false flag operation for short excursions in the output voltage, such as during line
and load transients. Furthermore, there is a delay between the point at which the output voltage is within
specified limits and the flag asserts Power Good. Because the RESET comparator and the regulation loop share
the same reference, the thresholds track with the output voltage. This allows the LM53625/35-Q1 to be specified
with a 96.5% maximum threshold, while at the same time specifying a 94 % worst case threshold with respect to
the actual output voltage for that device. This allows tighter tolerance than is possible with an external supervisor
device. The net result is a more accurate Power-Good function while expanding the system allowance for
transients, and so forth. RESET operation can best be understood by reference to Figure 10 and Figure 11. The
values for the various filter and delay times can be found in Timing Characteristics. Output voltage excursions
lasting less than TRESET-filter do not trip RESET. Once the output voltage is within the prescribed limits, a delay of
TRESET-act is imposed before RESET goes high.
This output consists of an open-drain NMOS; requiring an external pullup resistor to a suitable logic supply. It
can also be pulled up to either VCC or VOUT, through an appropriate resistor, as desired. The pin can be left
floating or grounded if the RESET function is not used in the application. When EN is pulled low, the flag output
isl also be forced low. With EN low, RESET remains valid as long as the input voltage is ≥ 1.5 V. The maximum
current into this pin should be limited to 10 mA, while the maximum voltage must be less than 8 V.
14
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
Feature Description (continued)
Figure 10. Static RESET Operation
Figure 11. RESET Timing Behavior
While the LM53625/35-Q1 reset function resembles a standard Power-Good function, its functionality is designed
to replace a discrete reset device, reducing additional component cost. There are three major differences
between the reset function and the normal power good function seen in most regulators.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
15
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
Feature Description (continued)
•
•
•
A delay has been added for release of reset. See Figure 11 and Figure 12 for more detail.
RESET Output signals a fault (pulls its output to ground) while the part is disabled.
RESET Continues to operate with input voltage as low as 1.5 V. Below this input voltage, RESET Output may
be high impedance.
The threshold voltage for the RESET function is specified taking advantage of the availability of the LM53625/35Q1 internal feedback threshold to the RESET circuit. This allows a maximum threshold of 96.5% of selected
output voltage to be specified at the same time as 96 % of actual set point. The net result is a more accurate
reset function while expanding the system allowance for transient response without the need for extremely
accurate internal circuitry.
8.3.2 Enable and Start-Up
Start-up and shutdown of the LM53625/35-Q1 are controlled by the EN input. Applying a voltage of ≥ 2 V
activates the device, while a voltage of ≤ 0.8 V is required to shut it down. The EN input may also be connected
directly to the input voltage supply. This input must not be left floating. The LM53625/35-Q1 utilizes a referencebased soft start that prevents output voltage overshoots and large inrush currents as the regulator is starting up.
A typical start-up waveform is shown in Figure 12 along with timing definitions.
The waveforms shown in Figure 12 indicate the sequence and timing between the enable input and the output
voltage and RESET. From the figure we can define several different start-up times depending on what is relevant
to the application. Table 3 lists some definitions and typical values for the timings.
Figure 12. Typical Start-up Waveform
Table 3. Typical Start-up Times
PARAMETER
tRESET-READY
16
Total start-up sequence
time
DEFINITION
VALUE
UNIT
Time from EN to RESET released
7.5
ms
tPOWER-UP
Start-up time
Time from EN to 90% of VOUT
4
ms
tSS
Soft-start time
Rise time of VOUT from 10% to 90%
3.2
ms
tEN
Delay time
Time from EN to start of VOUT rising
1
ms
tRESET-ACT
RESET time
Time from output voltage within 94% and RESET
released
3
ms
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
8.3.3 Soft-Start Function
Soft-start time is fixed internally at about 3 ms. Soft start is achieved by ramping the internal reference. The
LM53625/35-Q1 operates correctly even if there is a voltage present on the output before activation of the
LM53625/35-Q1 (pre-biased start-up). The device operates in AUTO mode during soft start, and the state of the
FPWM pin is ignored during that period.
8.3.4 Current Limit
The LM53625/35-Q1 incorporates valley current limit for normal overloads and for short-circuit protection. In
addition, the low-side switch is also protected from excessive negative current when the device is in FPWM
mode. Finally, a high-side peak-current limit is employed for protection of the top NMOS FET.
During overloads the low-side current limit, IL-LS (see Electrical Characteristics), determines the maximum load
current that the LM53625/35-Q1 can supply. When the low-side switch turns on, the inductor current begins to
ramp down. If the current does not fall below IL-LS before the next turnon cycle, then that cycle is skipped, and the
low-side FET is left on until the current falls below IL-LS. This is somewhat different than the more typical peak
current limit, and results in Equation 1 for the maximum load current.
IOUT
max
ILS
VIN VOUT VOUT
˜
2 ˜ FS ˜ L
VIN
(1)
The LM53625/35-Q1 uses two current limits, which allow use of smaller inductors than systems utilizing a single
current limit. A coarse high side or peak current limit is provided to protect against faults and saturated inductors.
A precision valley current limit prevents excessive average output current from the buck converter of the
LM53625/35-Q1. A new switching cycle is not initiated until inductor current drops below the valley current limit.
This scheme allows use of inductors with saturation current rated less than twice the rated operating current of
the LM53625/35-Q1.
If the converter keeps triggering valley current limit for more than about 64 clock cycles, the device turns off both
high and low side switches for approximately 5.5 ms (see TW in Timing Characteristics. If the overload is still
present after the hiccup time, another 64 cycles is counted, and the process is repeated. If the current limit is not
tripped for two consecutive clock cycles, the counter is reset. Figure 13 shows the inductor current with a hard
short on the output. The hiccup time allows the inductor current to fall to zero, resetting the inductor volt-second
balance. This is the method used for short-circuit protection and keeps the power dissipation low during a fault.
Of course the output current is greatly reduced in this condition (see Typical Characteristics. A typical shortcircuit transient and recovery is shown in Figure 14.
Short Removed
Short Applied
VOUT, 2V/div
Iinductor, 2A/div
5ms/div
21ms/div
ms/div
Figure 13. Inductor Current Bursts in Short Circuit
Figure 14. Short-Circuit Transient and Recovery
The high-side current limit trips when the peak inductor current reaches IL-HS (see Electrical Characteristics). This
is a cycle-by-cycle current limit and does not produce any frequency or current foldback. It is meant to protect the
high-side MOSFET from excessive current. Under some conditions, such as high input voltage, this current limit
may trip before the low-side protection. The peak value of this current limit varies with duty cycle.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
17
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
In FPWM mode, the inductor current is allowed to go negative. Should this current exceed INEG, the low side
switch is turned off until the next clock cycle. This is used to protect the low-side switch from excessive negative
current. When the device is in AUTO mode, the negative current limit is increased to about IZC (about 0 A). This
allows the device to operate in DCM.
The LM53625/35-Q1 response to a short circuit is: Peak current limit prevents excessive peak current while
valley current limit prevents excessive average inductor current. After a small number of cycles of valley current
limit triggers, hiccup mode is activated.
8.3.5 Hiccup Mode
In order to prevent excessive heating and power consumption under sustained short circuit conditions, a hiccup
mode is included. If an overcurrent condition is maintained, the LM53625/35-Q1 shuts off its output and waits for
TW (approximately 6 ms), after which the LM53625/35-Q1 restarts operation beginning by activating soft start.
Vout
Figure 15. Hiccup Operation
During hiccup mode operation the switch node of the LM53625/35-Q1 is high impedance after a short circuit or
overcurrent persists for a short duration. Periodically, the LM53625/35-Q1 attempts to restart. If the short has
been removed before one of these restart attempts, the LM53625/35-Q1 operates normally.
8.3.6 Synchronizing Input
It is often desirable to synchronize the operation of multiple regulators in a single system. This technique results
in better-defined EMI and can reduce the need for capacitance on some power rails. The LM53625/35-Q1
provides a SYNC input which allows synchronization with an external clock. The LM53625/35-Q1 implements an
in-phase locking scheme – the rising edge of the clock signal provided to the LM53625/35-Q1 input corresponds
to turning on the high-side device within the LM53625/35-Q1. This function is implemented using phase locking
over a limited frequency range eliminating large glitches upon initial application of an external clock. The clock
fed into the LM53625/35-Q1 replaces the internal free running clock but does not affect frequency foldback
operation. Output voltage continues to be well regulated with duty factors outside of the normal 15% through
87% range though at reduced frequency.
The internal clock of the LM53625/35-Q1 can be synchronized to a system clock through the SYNC input. This
input recognizes a valid high level as that ≥ 1.5 V, and a valid low as that ≤ 0.4 V. The frequency synchronization
signal must be in the range of 1.9 MHz to 2.3 MHz with a duty cycle of from 10% to 90%. The internal clock is
synced to the rising edge of the external clock. Ground this input if not used. The maximum voltage on this input
is 5.5 V and should not be allowed to float. See Device Functional Modes to determine which modes are valid for
synchronizing the clock.
The device remains in FPWM mode and operates in CCM for light loads when synchronization input is provided.
18
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
8.3.7 Undervoltage Lockout (UVLO) and Thermal Shutdown (TSD)
The LM53625/35-Q1 incorporates an input UVLO function. The device accepts an EN command when the input
voltage rises above about 3.64 V and shuts down when the input falls below about 3.3 V. See Electrical
Characteristics under VIN-OPERATE for detailed specifications.
TSD is provided to protect the device from excessive temperature. When the junction temperature reaches about
165°C, the device shuts down; re-start occurs at a temperature of about 150°C.
8.3.8 Input Supply Current
The LM53625/35-Q1 is designed to have very low input supply current when regulating light loads. One way this
is achieved is by powering much of the internal circuitry from the output. The BIAS pin is the input to the LDO
that powers the majority of the control circuits. By connecting the BIAS input to the output of the regulator, this
current acts as a small load on the output. This current is reduced by the ratio of VOUT/VIN, just like any other
load. Another advantage of the LM53625/35-Q1 is that the feedback divider is integrated into the device. This
allows the use of much larger resistors than can be used externally; >> 100 kΩ. This results in much lower
divider current than is possible with external resistors.
Equation 2 can be used as a guide to indicate how the various terms affect the input supply current in AUTO
mode in unloaded conditions. The Application Curves show measured values for the input supply current for both
the 3.3-V and the 5-V output voltage versions.
8.4 Device Functional Modes
Please refer to Table 4 and the following paragraphs for a detailed description of the functional modes for the
LM53625/35-Q1. These modes are controlled by the FPWM input as shown in Table 4. This input can be
controlled by any compatible logic, and the mode changed, while the regulator is operating. If it is desired to fix
the mode for a given application, the input can be either connected to ground, a logic supply, or the VCC pin, as
desired. The maximum input voltage on this pin is 5.5 V; the FPWM pin should not be allowed to float.
Table 4. Mode Selection
FPWM INPUT VOLTAGE
OPERATING MODE
> 1.5 V
Forced PWM: The regulator operates as a constant frequency, current mode, fullsynchronous converter for all loads; without diode emulation.
< 0.4 V
AUTO: The regulator moves between PFM and PWM as the load current changes, utilizing
diode-emulation mode to allow DCM (see the Glossary ).
8.4.1 AUTO Mode
In AUTO mode the device moves between PWM and PFM as the load changes. At light loads the regulator
operates in PFM . At higher loads the mode changes to PWM. The load currents at which the mode changes can
be found in the Application Curves.
In PWM, the converter operates as a constant frequency, current mode, full synchronous converter using PWM
to regulate the output voltage. While operating in this mode the output voltage is regulated by switching at a
constant frequency and modulating the duty cycle to control the power to the load. This provides excellent line
and load regulation and low output voltage ripple. When in PWM the converter synchronizes to any valid clock
signal on the SYNC input (see Dropout and Input Voltage Frequency Foldback ).
In PFM the high side FET is turned on in a burst of one or more cycles to provide energy to the load. The
frequency of these bursts is adjusted to regulate the output, while diode emulation is used to maximize efficiency
(see the Glossary). This mode provides high light-load efficiency by reducing the amount of input supply current
required to regulate the output voltage at small loads. This trades off very good light load efficiency for larger
output voltage ripple and variable switching frequency. Also, a small increase in the output voltage occurs in
PFM. The actual switching frequency and output voltage ripple will depend on the input voltage, output voltage,
and load. Typical switching waveforms for PFM are shown in Figure 16. See the Application Curves for output
voltage variation in AUTO mode. The SYNC input is ignored during PFM operation.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
19
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
A unique feature of this device is that a minimum input voltage is required for the regulator to switch from PWM
to PFM at light load. This feature is a consequence of the advanced architecture employed to provide high
efficiency at light loads. Figure 17 and Figure 18 indicates typical values of input voltage required to switch
modes at no load. Also, once the regulator switches to PFM, at light load, it remains in that mode if the input
voltage is reduced.
6.2
Light Load Activation Thsld (rising)
Light Load Deactivation Thsld (falling)
Input Voltage (V)
6
SW, 5V/div
VOUT, 50mV/div
5.8
5.6
5.4
5.2
Iinductor, 500mA/div
5
-40
10µs/div
2 ms/div
Figure 16. Typical PFM Switching Waveforms
-20
0
20
40
60
80
Temperature (qC)
100
120
140
D033
Figure 17. Input Voltage for Mode Change — Fixed
5-V Output, 2.2-µH Inductor
4.2
Light Load Activation Thsld (rising)
Light Load Deactivation Thsld (falling)
Input Voltage (V)
4
3.8
3.6
3.4
3.2
-40
-20
0
20
40
60
80
Temperature (qC)
100
120
140
D038
Figure 18. Input Voltage for Mode Change — Fixed 3.3-V Output, 2.2-µH Inductor
IQ_VIN is the current consumed by a converter utilizing a LM53635-Q1 or LM53625-Q1 device while regulating
without a load. While operating without a load, the LM53635-Q1 or LM53625-Q1 is only powering itself. The
device draws power from two sources, its VIN pin, IQ, and either its FB pin for fixed versions or BIAS pin for
adjustable versions, IB. Since BIAS or FB is connected to the output of the circuit, the power consumed is
converted from input power with an effective efficiency, ηeff, of approximately 80 %. Here, effective efficiency is
the added input power needed when lightly loading the converter of the LM53625-Q1 and LM53635- Q1 devices
and is divided by the corresponding additional load. This allows unloaded current to be calculated as follows:
Output Voltage
IQ _ VIN IQ IEN IB Idiv
Keff u Input Voltage
where
•
•
•
20
IQ_VIN is the current consumed by the operating (switching) buck converter utilizing the LM53625-Q1 or
LM53635-Q1 while unloaded.
IQ is the current drawn by the LM53625-Q1 or LM53635-Q1 from its VIN terminal. See IQ in Electrical
Characteristics.
IEN is current drawn by the LM53625-Q1 or LM53635-Q1 from its EN terminal. Include this current if EN is
connected to VIN. See IEN in Electrical Characteristics. Note that this current drops to a very low value if
connected to a voltage less than 5 V.
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
•
•
•
IB is bias/feedback current drawn by the LM53625-Q1 or LM53635-Q1 while the Buck converter utilizing it is
unloaded. See IB in Electrical Characteristics.
Idiv is the current drawn by the feedback voltage divider used to set output voltage for adjustable devices. This
current is zero for fixed output voltage devices.
ηeff is the light load efficiency of the Buck converter with IQ_VIN removed from the input current of the buck
converter input current. 0.8 is a conservative value that can be used under normal operating conditions.
(2)
NOTE
The EN pin consumes a few micro-amperes when tied to high; see IEN. Add IEN to IQ as
shown in Equation 2 if EN is tied to VIN. If EN is tied to a voltage less than 5 V, virtually no
current is consumed allowing EN to be used as an UVLO pin once a voltage divider is
added.
8.4.2 FPWM Mode
With a logic high on the FPWM input, the device is locked in PWM mode. This operation is maintained, even at
no-load, by allowing the inductor current to reverse its normal direction. This mode trades off reduced light load
efficiency for low output voltage ripple, tight output voltage regulation, and constant switching frequency. In this
mode, a negative current limit of INEG is imposed to prevent damage to the low-side FET of the regulator. When
in FPWM the converter synchronizes to any valid clock signal on the SYNC input (see Dropout and Input Voltage
Frequency Foldback.
When constant frequency operation is more important than light load efficiency, pull the LM53625/35-Q1 FPWM
input high or provide a valid synchronization input. Once activated, this feature ensures that the switching
frequency stays above the AM frequency band, while operating between the minimum and maximum duty cycle
limits. Essentially, the diode emulation feature is turned off in this mode. This means that the device remains in
CCM under light loads. Under conditions where the device must reduce the on time or off time below the ensured
minimum, the frequency reduces to maintain the effective duty cycle required for regulation. This can occur for
high input/output voltage ratios.
With the FPWM pin pulled low (normal mode), the diode emulation feature is activated. Device operation is the
same as above; however, the regulator goes into DCM operation when the valley of the inductor current reaches
zero.
This feature may be activated and deactivated while the part is regulating without removing the load. This feature
activates and deactivates gradually, over approximately 40 µs, preventing perturbation of output voltage. When in
FPWM mode, a limited reverse current is allowed through the inductor allowing power to pass from the regulators
output to its input. In this case, care must be taken to ensure that a large enough input capacitor is used to
absorb this reverse current.
NOTE
While FPWM is activated, larger currents pass through the inductor than in AUTO mode
when lightly loaded. This may result in more EMI, though at a predictable frequency. Once
loads are heavy enough to necessitate CCM operation, FPWM has no measurable effect
on the operation of the regulator.
8.4.3 Dropout
One of the parameters that influences the dropout performance of a buck regulator is the minimum off time. As
the input voltage is reduced, to near the output voltage, the off time of the high-side switch starts to approach the
minimum value (see Electrical Characteristics). Beyond this point the switching may become erratic and/or the
output voltage falls out of regulation. To avoid this problem, the LM53625/35-Q1 automatically reduces the
switching frequency to increase the effective duty cycle. This results in two specifications regarding dropout
voltage, as shown in System Characteristics. One specification indicates when the switching frequency drops to
1.85 MHz; avoiding the A.M. radio band. The other specification indicates when the output voltage has fallen to
3% of nominal. See the Application Curves for typical dropout values. The overall dropout characteristic for the 5V option can be seen in Figure 19 and Figure 20. The SYNC input is ignored during frequency foldback in
dropout. Additional dropout information is discussed in for 5-V output (Application Curves and for 3.3 V output
(Application Curves).
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
21
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
5.2
2.5E+6
Switching Frequency (Hz)
Output Voltage (V)
5
4.8
4.6
0A
1A
2A
3A
3.5 A
4.4
4.2
4
2E+6
1.5E+6
1E+6
0A
1A
2A
3A
3.5 A
5E+5
0
4
4.25
4.5
4.75
5
Input Voltage (V)
5.25
Figure 19. Overall Dropout Characteristics
(VOUT = 5 V)
5.5
4
4.5
D029
5
5.5
Input Voltage (V)
6
6.5
D030
Figure 20. Frequency Dropout Characteristics
(VOUT = 5 V)
8.4.4 Input Voltage Frequency Foldback
At higher input voltages the on time of the high-side switch becomes small. When the minimum is reached (see
Electrical Characteristics), the switching may become erratic and/or the output voltage may fall out of regulation.
To avoid this behavior, the LM53625/35-Q1 automatically reduces the switching frequency at input voltages
above about 20 V (see Application Curves). In this way the device avoids the minimum on-time restriction and
maintains regulation at abnormally high battery voltages. The SYNC input is ignored during frequency foldback at
high input voltages. Frequency foldback patterns are different for the fixed 3.3-V and the 5-V output options. The
fixed 3.3-V option has a deeper foldback pattern to accommodate the lower duty cycle. The adjustable option has
a fold-back patterns is similar to that of the fixed 3.3-V option.
8.5 Spread-Spectrum Operation
The spread spectrum is a factory option. In order to find which parts have spread spectrum enabled, see Device
Comparison.
The purpose of the spread spectrum is to eliminate peak emissions at specific frequencies by spreading
emissions across a wider range of frequencies than a part with fixed frequency operation. In most systems
containing the LM53625-Q1 and LM53635-Q1 devices, low frequency conducted emissions from the first few
harmonics of the switching frequency can be easily filtered. A more difficult design criterion is reduction of
emissions at higher harmonics which fall in the FM band. These harmonics often couple to the environment
through electric fields around the switch node. The LM53625-Q1 and LM53635-Q1 devices use a ±3% spread of
frequencies which spread energy smoothly across the FM band but is small enough to limit sub-harmonic
emissions below its switching frequency. Peak emissions at the part’s switching frequency are only reduced by
slightly less than 1 dB, while peaks in the FM band are typically reduced by more than 6 dB.
The LM53625-Q1 and LM53635-Q1 devices use a cycle to cycle frequency hopping method based on a linear
feedback shift register (LFSR). Intelligent pseudo random generator limits cycle to cycle frequency changes to
limit output ripple. Pseudo random pattern repeats by approximately 8 Hz which is below the audio band.
The spread spectrum is only available while the clock of the LM53625-Q1 and LM53635-Q1 devices is free
running at its natural frequency. Any of the following conditions overrides spread spectrum, turning it off:
1. An external clock is applied to the SYNC/MODE terminal.
2. The clock is slowed due to operation low input voltage – this is operation in dropout.
3. The clock is slowed due to high input voltage – input voltage above approximately 21 V disables spread
spectrum.
4. The clock is slowed under light load in Auto mode – this is normally not seen above 200 mA of load. In
FPWM mode, spread spectrum is active even if there is no load.
22
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The LM53625/35-Q1 is a step-down DC-DC converter, typically used to convert a higher DC voltage to a lower
DC voltage with a maximum output current of 2.5 A or 3.5 A. The following design procedures can be used to
select components for the LM53625/35-Q1. Alternately, the WEBENCH® Design Tool may be used to generate a
complete design. This tool utilizes an iterative design procedure and has access to a comprehensive database of
components. This allows the tool to create an optimized design and allows the user to experiment with various
design options.
9.2 Typical Applications
9.2.1 General Application
Figure 21 shows a general application schematic. FPWM, SYNC and EN are digital inputs. RESET is an opendrain output. FB connection is different for the fixed output options and the adjustable option.
• The FPWM pin can be connected to GND to enable light-load PFM operation. Select this option if current
consumption at light load is critical. The pin can be connected to VCC or VIN for forced 2-MHz operation.
Select this option if constant switching frequency is critical over the entire load range. The pin can also be
driven by an external signal and can be toggled while the part is in operation (by an MCU for example.) Refer
to the Electrical Characteristics and Device Functional Modes for more details on the operation and signal
requirements of the FPWM pin.
• The SYNC pin can be used to control the switching frequency and the phase of the converter. If the function
is not needed, tie the SYNC pin to GND or 3 V.
• The RESET pin can be left floating if the function is not required. If the function is needed, the pin must be
connected to a DC rail through a pullup resistor (100 kΩ is the typical recommended value). Check Electrical
Characteristics and RESET Flag Output for the details of the RESET-pin function.
• If the device is a fixed-output version (3.3 V or 5 V output option), connect the FB pin directly to the output. In
the case of an adjustable-output part, connect the output to the FB pin through a voltage divider. See Detailed
Design Procedure for details on component selection.
• The BIAS pin can be connected directly to the output except in applications that can experience inductive
shorts (such as cases with long leads on the output). In those cases, a 3 Ω or so is necessary between the
output and the BIAS pin, and a small capacitor to GND is necessary close to the BIAS pin (CBIAS).
Alternatively, a Schottky diode can be connected between the OUT and GND to limit the negative voltage that
can arise on the output during inductive shorts. In addition, BIAS can also be connected to an external rail if
necessary and if available. The typical current into the bias pin is 15 mA when the device is operating in
PWM mode at 2.1 MHz.
• Power components must be chosen carefully for proper operation of the converter. Detailed Design
Procedure discusses the details of the process of choosing the input capacitors, output capacitors, and
inductor for the application.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
23
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
Typical Applications (continued)
Figure 21. General Application Circuit
9.2.1.1 Design Requirements
See Table 8, Table 9, and Table 10. The minimum input voltage shown in Figure 21 is not the minimum
operating voltage of the LM53625-Q1/LM53635-Q1. Rather, it is a typical operating range for the systems. For
the complete information regarding minimum input voltage, please refer to Electrical Characteristics
9.2.1.2 Detailed Design Procedure
9.2.1.2.1 External Components Selection
The device requires input capacitors and an output inductor-capacitor filter. These components are critical to the
performance of the device.
9.2.1.2.1.1 Input Capacitors
The input capacitor supplies the AC switching current drawn from the switching action of the internal power
FETs. The input current of a buck converter is discontinuous, so the ripple current supplied by the input capacitor
is large. The input capacitor must be rated to handle both the RMS current and the dissipated power.
The device is designed to be used with ceramic capacitors on the input of the buck regulator. The recommended
dielectric type of these capacitors is X5R, X7R, or of comparable material to maintain proper tolerances over
voltage and temperature.
The device requires a minimum of 22 µF of ceramic capacitance at the input. TI recommends 2 × 10 µF, 10 µF
for PVIN1 and 10 µF for PVIN2. Place these capacitors close to the PVIN1 and PGND1 / PVIN2 and PGND2
pads.
24
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
Typical Applications (continued)
In addition, it is especially important to have small ceramic capacitors of 10 nF to 100 nF very close to the PVIN1
and PVIN2 inputs in order to minimize ringing and EMI generation due to the high speed switching of the device
coupled with trace inductance.
Many times it is desirable to use an additional electrolytic capacitor on the input, in parallel with the ceramics.
This is especially true if longs leads/traces are used to connect the input supply to the regulator. The moderate
ESR of this capacitor can help damp any ringing on the input supply caused by long power leads. The use of this
additional capacitor will also help with voltage dips caused by input supplies with unusually high impedance.
9.2.1.2.1.1.1 Input Capacitor Selection
The ceramic input capacitors provide a low impedance source to the regulator in addition to supplying ripple
current and isolating switching noise from other circuits. Table 5 shows the nominal and minimum values of total
input capacitance recommenced for the LM53625/35-Q1. Also shown are the measured values of effective
capacitance for the indicated capacitor. In addition, small high frequency bypass capacitors connected directly
between the VIN and PGND pins are very helpful in reducing noise spikes and aid in reducing conducted EMI. TI
recommends that a small case size 10-nF ceramic capacitor be placed across the input, as close to the device
as possible. Additional high-frequency capacitors can be used to help manage conducted EMI or voltage spike
issues that may be encountered.
Table 5. Recommended Input Capacitors
NOMINAL INPUT CAPACITANCE
MINIMUM INPUT CAPACITANCE
RATED
CAPACITANCE
MEASURED CAPACITANCE (1)
RATED CAPACITANCE
MEASURED
CAPACITANCE (1)
3 × 10 μF
22.5 μF
2 × 10 μF
15 μF
(1)
PART NUMBER
CL32B106KBJNNNE
Measured at 14 V and 25°C.
9.2.1.2.1.2 Output Inductors and Capacitors Selection
There are several design considerations related to the selection of output inductors and capacitors:
• Load transient response
• Stability
• Efficiency
• Output ripple voltage
• Overcurrent ruggedness
The device has been optimized for use with nominal LC values as shown in the Figure 21.
9.2.1.2.1.2.1 Inductor Selection
The LM53625/35-Q1 is optimized for a nominal inductance of 2.2 μH for the 5-V and 3.3-V versions. This gives a
ripple current that is approximately 20% to 30% of the full load current of 3.5 A. For output voltages greater than
5 V, a proportionally larger inductor can be used, thus keeping the ratio of inductor current slope to internal
compensating slope constant.
The most important inductor parameters are saturation current and parasitic resistance. Inductors with a
saturation current of between 7 A and 8 A are appropriate for most applications when using the LM53625/35-Q1.
Of course, the inductor parasitic resistance must be as low as possible to reduce losses at heavy loads. Table 6
gives a list of several possible inductors that can be used with the LM53625/35-Q1.
The LM53625 and LM53635 devices run in current mode and with internal compensation. This compensation is
stable with inductance between 1.5 µH and 10 µH. For most applications, use 2.2 µH with the fixed 5-V and 3.3V versions of the LM53625 and LM53635 devices. Adjustable devices operate at the same frequency under high
input-voltage conditions as devices set to deliver 3.3 V (see Figure 48). Inductor current ripple at high input
voltages can become excessive when using a 2.2-µH inductor with an adjustable device that is delivering output
voltage above 6 V. A 4.7-µH inductor might be necessary. Inductance that is too high is not recommended as it
can result in poor load transient behavior and instability for extreme inductance choice. See Table 6 for typical
recommended values.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
25
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
The inductor must be rated to handle the peak load current plus the ripple current — take care when reviewing
the different saturation current ratings specified by different manufacturers. Saturation current ratings are typically
specified at 25°C, so ratings at maximum ambient temperature of the application should be requested from the
manufacturer. For the LM53635, TI recommends a saturation current of 7.5 A or higher, and for the LM53625, a
saturation current of 6.5 A or higher is recommended
Table 6. Recommended Inductors
MANUFACTURER
PART NUMBER
SATURATION CURRENT
DC RESISTANCE
Würth
7440650022
6A
15 mΩ
Coilcraft
DO3316T-222MLB
7.8 A
11 mΩ
Coiltronics
MPI4040R3-2R2-R
7.9 A
48 mΩ
Vishay
IHLP2525CZER2R2M01
8A
18 mΩ
Vishay
IHLP2525BDER2R2M01
6.5 A
28 mΩ
The designer should choose the inductors that best match the system requirements. A very wide range of
inductors are available as regarding physical size, height, maximum current (thermally limited, and inductance
loss limited), series resistance, maximum operating frequency, losses, and so forth. In general, inductors of
smaller physical size have higher series resistance (DCR) and implicitly lower overall efficiency is achieved. Very
low-profile inductors may have even higher series resistance. TI recommends finding the best compromise
between system performance and cost.
9.2.1.2.1.2.2 Output Capacitor Selection
The LM53625/35-Q1 is designed to work with low-ESR ceramic capacitors. For automotive applications, TI
recommends X5R and X7R type capacitors. The effective value of these capacitors is defined as the actual
capacitance under voltage bias and temperature. All ceramic capacitors have a large voltage coefficient, in
addition to normal tolerances and temperature coefficients. Under DC bias, the capacitance value drops
considerably. Larger case sizes and/or higher voltage capacitors are better in this regard. To help mitigate these
effects, multiple small capacitors can be used in parallel to bring the minimum effective capacitance up to the
desired value. This can also ease the RMS current requirements on a single capacitor. Table 7 shows the
nominal and minimum values of total output capacitance recommended for the LM53625/35-Q1. The values
shown also provide a starting point for other output voltages, when using the adjustable option. Also shown are
the measured values of effective capacitance for the indicated capacitor. More output capacitance can be used
to improve transient performance and reduce output voltage ripple.
In practice, the output capacitor has the most influence on the transient response and loop phase margin. Load
transient testing and Bode plots are the best way to validate any given design and should always be completed
before the application goes into production. Make a careful study of temperature and bias voltage variation of any
candidate ceramic capacitor in order to ensure that the minimum value of effective capacitance is provided. The
best way to obtain an optimum design is to use the Texas Instruments WEBENCH Design Tool.
In adjustable applications the feed-forward capacitor, CFF, provides another degree of freedom when stabilizing
and optimizing the design. Refer to Optimizing Transient Response of Internally Compensated dc-dc Converters
With Feedforward Capacitor (SLVA289) for helpful information when adjusting the feed-forward capacitor.
In addition to the capacitance shown in Table 7, a small ceramic capacitor placed on the output can help to
reduce high frequency noise. Small case-size ceramic capacitors in the range of 1 nF to 100 nF can be very
helpful in reducing spikes on the output caused by inductor parasitics.
Limit the maximum value of total output capacitance to between 300 μF and 400 μF. Large values of output
capacitance can prevent the regulator from starting up correctly and adversely effect the loop stability. If values in
the range given above, or greater, are to be used, then a careful study of start-up at full load and loop stability
must be performed.
26
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
Table 7. Recommended Output Capacitors
OUTPUT VOLTAGE
NOMINAL OUTPUT CAPACITANCE
MINIMUM OUTPUT CAPACITANCE
PART NUMBER
RATED
CAPACITANCE
MEASURED
CAPACITANCE (1)
RATED
CAPACITANCE
MEASURED
CAPACITANCE (1)
3.3 V (fixed option)
3 × 22 µF
63 µF
2 × 22 µF
42 µF
C3225X7R1C226M250AC
5 V (fixed option)
3 × 22 µF
60 µF
2 × 22 µF
40 µF
C3225X7R1C226M250AC
6V
5 × 22 μF
98 µF
3 × 22 μF
58 µF
C3225X7R1C226M250AC
5 × 22 μF
80 µF
3 × 22 μF
48 µF
C3225X7R1C226M250AC
10 V
(1)
(2)
(2)
Measured at indicated VOUT at 25°C.
L = 4.7 μH.
The output capacitor of a switching converter absorbs the AC ripple current from the inductor and provides the
initial response to a load transient. The ripple voltage at the output of the converter is the product of the ripple
current flowing through the output capacitor and the impedance of the capacitor. The impedance of the capacitor
can be dominated by capacitive, resistive, or inductive elements within the capacitor, depending on the frequency
of the ripple current. Ceramic capacitors have very low ESR and remain capacitive up to high frequencies. Their
inductive component can be usually neglected at the frequency ranges the switcher operates.
The output-filter capacitor smooths out the current flow from the inductor to the load and helps maintain a steady
output voltage during transient load changes. It also reduces output voltage ripple. These capacitors must be
selected with sufficient capacitance and low enough ESR to perform these functions.
Consult Output Ripple Voltage for Buck Switching Regulator (SLVA630) for more details on the estimation of the
output voltage ripple for this converter.
9.2.1.2.2 Setting the Output Voltage
For the fixed output voltage versions, the FB input is connected directly to the output voltage node. Preferably,
near the top of the output capacitor. If the feedback point is located further away from the output capacitors (that
is, remote sensing), then a small 100-nF capacitor may be needed at the sensing point.
9.2.1.2.2.1 FB for Adjustable Versions
The adjustable version of the LM53625-Q1 and LM53635-Q1 devices regulates output voltage to a level that
results in the FB node being VREF, which is approximately 1 V; see Electrical Characteristics. Output voltage
given a specific feedback divider can be calculated using Equation 3:
R
RFBT
Output Voltage Vref u FBB
RFBB
(3)
See Figure 54 for an example of the use of adjustable versions of the LM53625-Q1 and LM53635-Q1 devices.
To ensure proper behavior for all modes of operation, a 50 kΩ resistor is recommended for RFBT. RFBB can then
be determined using :
Vref u RFBT
RFBB
Output Voltage Vref
(4)
In addition a feed-forward capacitor CFF may be required to optimize the transient response. For output voltages
greater than 6 V, the WEBENCH Design Tool can be used to optimize the design.
9.2.1.2.3 VCC
The VCC pin is the output of the internal LDO used to supply the control circuits of the LM53625/35-Q1. This
output requires a 4.7-µF, 10-V ceramic capacitor connected from VCC to GND for proper operation. X7R type is
recommended for automotive applications. In general this output must not be loaded with any external circuitry.
However, it can be used to supply a logic level to the FPWM input or for the pullup resistor used with the RESET
output. The nominal output of the LDO is 3.15 V.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
27
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
9.2.1.2.4 BIAS
The BIAS pin is the input to the internal LDO. As mentioned in Input Supply Current, this input is connected to
VOUT in order to provide the lowest possible supply current at light loads. Because this input is connected directly
to the output, it must be protected from negative voltage transients. Such transients may occur when the output
is shorted at the end of a long PCB trace or cable. If this is likely in a given application, then place a small
resistor in series between the BIAS input and VOUT, as shown in Figure 24. Size the resistor to limit the current
out of the BIAS pin to < 100 mA. Values in the range of 2 Ω to 5 Ω are usually sufficient. Values greater than 5 Ω
are not recommended. As a rough estimate, assume that the full negative transient will appear across RBIAS and
design for a current of < 100 mA. In severe cases, a Schottky diode can be placed in parallel with the output to
limit the transient voltage and current.
When a resistor is used between the output and the BIAS pin, a 0.1-µF capacitor is required close to the BIAS
pin. In general, TI recommends having a 0.1-µF capacitor near the BIAS pin, regardless of the presence or not of
the resistor, unless the trace between the output capacitors and the BIAS pin is very short.
The typical current into the bias pin is 15 mA when the device is operating in PWM mode at 2.1 MHz.
9.2.1.2.5 CBOOT
The LM53625/35-Q1 requires a boot-strap capacitor between the CBOOT pin and the SW pin. This capacitor
stores energy that is used to supply the gate drivers for the power MOSFETs. A ceramic capacitor of 0.47 µF, ≥
6.3 V is required.
9.2.1.2.6 Maximum Ambient Temperature
As with any power conversion device, the LM53625/35-Q1 dissipates internal power while operating. The effect
of this power dissipation is to raise the internal temperature of the converter above ambient. The internal die
temperature (TJ) is a function of the ambient temperature, the power loss, and the effective thermal resistance,
RθJA of the device and PCB combination. The maximum internal die temperature for the LM53625/35-Q1 is
150°C, thus establishing a limit on the maximum device power dissipation and therefore load current at high
ambient temperatures. Equation 5 shows the relationships between the important parameters.
IOUT
TJ TA
K
1
˜
˜
R TJA
1 K VOUT
(5)
The device uses an advanced package technology that utilizes the pads/pins as heat spreading paths. As a
result, the pads should be connected to large copper areas in order to dissipate the heat from the IC. All pins
provide some heat relief capability but the PVINs, PGNDs and SW pins are of particular importance for proper
heat dissipation. Utilization of all the board layers for heat dissipation using vias as heat pipes is recommended.
The Layout Guideline section includes example that shows layout for proper heat management.
9.2.1.3 Application Curves
These parameters are not tested and represent typical performance only. Unless otherwise stated, the following
conditions apply: VIN = 12 V, TA = 25°C. For the purpose of offering the more information to the designer,
information for the application with FPWM pin high (FPWM mode) and FPWM pin low (AUTO mode) is included,
although the schematic shows the application running specifically in FPWM mode. The mode is specified under
each following graph.
28
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
4
4
8 Vin
12 Vin
13.5 Vin
18 Vin
36 Vin
3
5.5 Vin
8 Vin
12 Vin
13.5 Vin
18 Vin
36 Vin
3.5
Power Dissipation (W)
Power Dissipation (W)
3.5
2.5
2
1.5
1
0.5
3
2.5
2
1.5
1
0.5
0
0
0
0.5
1
1.5
2
Output Current (A)
2.5
3
3.5
0
0.5
D031
Figure 22. Power Dissipation 5-V Output
1
1.5
2
Output Current (A)
2.5
3
3.5
D031
D032
Figure 23. Power Dissipation 3.3-V Output
9.2.2 Fixed 5-V Output for USB-Type Applications
Figure 24. Fixed 5-V, 3.5-A Output Power Supply
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
29
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
9.2.2.1 Design Requirements
Example requirements for a typical 5-V application. The input voltages are here for illustration purposes only.
See Electrical Characteristics for minimum operating input voltage. The minimum input voltage necessary to
achieve proper output regulation depends on the components used. See Figure 31 for typical drop-out behavior.
Table 8. Example Requirements for 5-V Typical Application
DESIGN PARAMETER
EXAMPLE VALUE
Input voltage range
8 V to 18 V steady state, 5.5 V to 36 V transients
Output current
0 A to 3.5 A
Switching Frequency at 0-A load
Critical: must have > 1.85 MHz
Current Consumption at 0-A load
Not critical: < 100 mA acceptable
Synchronization
Yes: 1.9 MHz supplied by MCU
9.2.2.2 Detailed Design Procedure
• BIAS is connected to the output. This example assumes that the load is connected to the output through long
wires so a 3 Ω resistor is inserted to minimize risks of damage to the part during load shorts. As a result a
0.1-µF capacitor is required close to the bias pin.
• FB is connected directly to the output. BIAS and FB are connected to the output via separate traces. This is
important in order to reduce noise and achieve good performances. See Layout Guidelines for more details
on the proper layout method.
• SYNC is connected to ground through a pulldown resistor, and an external synchronization signal can be
applied. The pulldown resistor ensures that the pin is not floating when the SYNC pin is not driven by any
source.
• EN is connected to VIN so the device operates as soon as the input voltage rises above the VIN-OPERATE
threshold.
• FPWM is connected to VCC. This causes the device to operate in FPWM mode. In this mode, the switching
frequency is not affected by the output current and is ensured to be within the boundaries set by FSW. The
drawback is that the efficiency is not optimized for light loads. See Device Functional Modes for more details.
• A 4.7-µF capacitor is connected between VCC and GND close to the VCC pin This ensures stable operation
of the internal LDO.
• RESET is biased to the output in this example. A pullup resistor is necessary. A 100-kΩ is selected for this
application and is generally sufficient. The value can be selected to match the needs of the application but
must not lead to excessive current into the RESET pin when RESET is in a low state. Consult Absolute
Maximum Ratings for the maximum current allowed. In addition, a low pullup resistor could lead to an
incorrect logic level due to the value of RRESET . Consult Electrical Characteristics for details on the RESET
pin.
• Input capacitor selection is detailed in Input Capacitors. It is important to connect small high-frequency
capacitors CIN_HF1 and CIN_HF2 as close to both inputs PVIN1 and PVIN2 as possible.
• Output capacitor selection is detailed in Output Capacitor Selection.
• Inductor selection is detailed in Inductor Selection. In general, a 2.2-µH inductor is recommended for the fixed
output options. For the adjustable options, the inductance can vary with the output voltage due to ripple and
current limit requirements.
9.2.2.3 Application Curves
The following characteristics apply only to the circuit of Fixed 5-V Output for USB-Type Applications. These
parameters are not tested and represent typical performance only. Unless otherwise stated, the following
conditions apply: VIN = 12 V, TA = 25°C. For the purpose of offering the more information to the designer,
information for the application with FPWM pin high (FPWM mode) and FPWM pin low (AUTO mode) is included,
although the schematic shows the application running specifically in FPWM mode. The mode is specified under
each following graph.
30
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
100%
100%
90%
95%
80%
90%
85%
Efficiency
Efficiency
70%
60%
50%
40%
20%
10%
1E-5
75%
5.5Vin
8Vin
12Vin
13.5Vin
18Vin
36Vin
70%
65%
8Vin
12Vin
13.5Vin
18Vin
30%
80%
60%
55%
50%
0.0001
0.001
0.01
Output Current (A)
VOUT = 5 V
0.10.2 0.5 1 2 34
0
0.5
1
D002
AUTO
VOUT = 5 V
2.5
3.5
D006
Figure 26. Efficiency
5.08
5.05
8Vin
12Vin
18Vin
36Vin
5.025
5
Output Voltage (V)
5.06
5.04
5.02
5
4.975
4.95
4.925
4.9
5.5Vin
8Vin
12Vin
13.5Vin
18Vin
36Vin
4.875
4.85
4.98
4.825
4.96
4.775
4.8
0
0.5
1
VOUT = 5 V
1.5
2
Output Current (A)
2.5
3
3.5
0
0.5
1
D003
AUTO
VOUT = 5 V
Figure 27. Load and Line Regulation
1.5
2
Output Current (A)
2.5
3
3.5
D007
FPWM
Figure 28. Load and Line Regulation
36
550
34
500
32
450
Output Current (mA)
Operating Current (PA)
3
FPWM
Figure 25. Efficiency
Output Voltage (V)
1.5
2
Output Current (A)
30
28
26
24
400
350
300
250
22
200
20
150
100
18
6
9
12
VOUT = 5 V
15
18
21
24
Input Voltage (V)
27
30
33
36
4
8
12
D015
AUTO
IOUT = 0 A
Figure 29. Input Supply Current (includes Leakage Current
of the Capacitor)
16
20
24
Input Voltage (V)
28
32
36
D017
VOUT = 5 V
Figure 30. Load Current for PFM-to-PWM transition
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
31
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
1.5
1.5
-40C
25C
105C
1.2
Dropout Voltage (V)
Dropout Voltage (V)
1.2
0.9
0.6
0.3
0.9
0.6
-40C
25C
105C
0.3
0
0
0
0.5
1
1.5
2
Output Current (A)
2.5
3
3.5
0
0.5
1
D022
VOUT = 5 V
1.5
2
Output Current (A)
2.5
3
3.5
D021
VOUT = 5 V
Figure 32. Dropout for ≥ 1.85 MHz
Figure 31. Dropout for –3% Regulation
2.5
5E+6
2
1E+5
Fsw (MHz)
Switching Frequency (Hz)
1E+6
1E+4
8Vin
12Vin
18Vin
1E+3
1.5
1
0.5
1E+2
5E+1
1E-6
0
1E-5
0.0001 0.001
0.01
Output Current (A)
VOUT = 5 V
0.1
1
5
0
4
8
12
D018
AUTO
VOUT = 5 V
Figure 33. Switching Frequency vs Load Current
16
20
24
Vin (V)
28
32
36
40
D001
FPWM
Figure 34. Switching Frequency vs Input Voltage
5
Output Current (A)
4.5
4
3.5
LM53635
LM53625
3
5
10
VOUT = 5 V
15
20
25
Input Voltage (V)
30
35
40
D005
L = 2.2µH
Figure 35. Output Current Level Limit Before Overcurrent
Protection
32
Submit Documentation Feedback
AUTO
COUT = 3 × 22
µF
VOUT = 5 V
IOUT = 10 mA to 3.5
A
L = 2.2 µH
TR = TF = 1 µs
Figure 36. Load Transients
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
FPWM
COUT = 3 × 22 µF
VOUT = 5 V
IOUT = 0 A to 3.5 A
L = 2.2 µH
TR = TF = 1µs
Figure 37. Load Transient
9.2.3 Fixed 3.3-V Output
Figure 38. Fixed 3.3-V, 3.5-A Output Power Supply
9.2.3.1 Design Requirements
Example requirements for a typical 3.3-V application. The input voltages are here for illustration purposes only.
See Electrical Characteristics for minimum operating input voltage. The minimum input voltage necessary to
achieve proper output regulation depends on the components used. See Figure 45 for typical drop-out behavior.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
33
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
Table 9. Example Requirements for 3.3-V Application
DESIGN PARAMETER
EXAMPLE VALUE
Input voltage range
8-V to 18-V steady state, 4.0-V to 36-V transients
Output current
0 A to 3.5 A
Swtiching Frequency at 0-A load
Not critical: Need >1.85 MHz at high load only
Current Consumption at 0-A load
Critical: Need to ensure low current consumption to reduce battery drain
Synchronization
No
9.2.3.2 Detailed Design Procedure
• BIAS is connected to the output. This example assumes that the load is close to the output so no bias
resistance is necessary. A 0.1-µF capacitor is still recommended close to the bias pin.
• FB is connected directly to the output. BIAS and FB are connected to the output via separate traces. This is
important to reduce noise and achieve good performances. See Layout Guidelines for more details on the
proper layout method.
• SYNC is connected to ground directly as there is no need for this function in this application.
• EN is connected to VIN so the device perates as soon as the input voltage rises above the VIN-OPERATE
threshold.
• FPWM is connected to GND. This causes the device to operate in AUTO mode. In this mode, the switching
frequency is adjusted at light loads to keep efficiency maximum. As a result the switching frequency will
change with the output current until medium load is reached. The part will then switch at the frequency
defined by FSW. See Device Functional Modes for more details.
• A 4.7-µF capacitor is connected between VCC and GND close to the VCC pin This ensures stable operation
of the internal LDO.
• RESET is biased to an external rail in this example. A pullup resistor is necessary. A 100 kΩ is selected for
this application and is generally sufficient. The value can be selected to match the needs of the application
but must not lead to excessive current into the RESET pin when RESET is in a low state. Consult Absolute
Maximum Ratings for the maximum current allowed. In addition, a low pull-up resistor could lead to an
incorrect logic level due to the value of RRESET . Consult Electrical Characteristics for details on the RESET
pin.
• it is important to connect small high frequency capacitors CIN_HF1 and CIN_HF2 as close to both inputs PVIN1
and PVIN2 as possible. For the detailed process of choosing input capacitors, refer to Input Capacitors.
• Output capacitor selection is detailed in Output Capacitor Selection.
• Inductor selection is detailed in Inductor Selection. In general, a 2.2-µH inductor is recommended for the fixed
output options. For the adjustable options, the inductance can vary with the output voltage due to ripple and
current limit requirements.
9.2.3.3 Application Curves
The following characteristics apply only to the circuit of Figure 38. These parameters are not tested and
represent typical performance only. Unless otherwise stated, the following conditions apply: VIN = 12 V, TA =
25°C. For the purpose of offering the more information to the designer, information for the application with FPWM
pin high (FPWM mode) and FPWM pin low (AUTO mode) is included, although the schematic shows the
application running specifically in AUTO mode. The mode is specified under each of the following graphs.
34
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
100%
3.4
90%
3.38
5.5Vin
8Vin
12Vin
18Vin
36Vin
3.36
Output Voltage (V)
Efficiency
80%
70%
60%
50%
8Vin
12Vin
13.5Vin
18Vin
40%
30%
20%
0.0001
3.34
3.32
3.3
3.28
3.26
3.24
3.22
3.2
0.001
0.01
0.05
Output Current (A)
VOUT = 3.3 V
0.2 0.5 1
2 34
0
AUTO
1
VOUT = 3.3 V
Figure 39. Efficiency
3.4
95%
3.38
90%
3.36
85%
3.34
Output Voltage (V)
100%
75%
5.5Vin
8Vin
12Vin
13.5Vin
18Vin
36Vin
70%
65%
60%
55%
1.5
2
Output Current (A)
2.5
3
3.5
D009
AUTO
Figure 40. Load and Line Regulation
80%
Efficiency
0.5
D008
5.5Vin
8Vin
12Vin
18Vin
36Vin
3.32
3.3
3.28
3.26
3.24
3.22
50%
3.2
0
0.5
1
VOUT = 3.3 V
1.5
2
Output Current (A)
2.5
3
3.5
0
0.5
1
D010
FPWM
VOUT = 3.3 V
Figure 41. Efficiency
1.5
2
Output Current (A)
2.5
3
3.5
D011
FPWM
Figure 42. Load and Line Regulation
900
45
800
700
Output Current (mA)
Operating Current (PA)
40
35
30
25
600
500
400
300
200
20
100
0
15
0
5
VOUT = 3.3 V
10
15
20
25
Input Voltage (V)
30
35
40
0
6
D016
AUTO
IOUT = 0A
Figure 43. Input Supply Current (Includes Leakage Current
of Capacitor)
12
18
24
Input Voltage (V)
30
36
42
D014
VOUT = 3.3 V
Figure 44. Load Current for PFM-to-PWM Transition
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
35
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
1.5
1.5
-40C
25C
105C
1.2
Dropout Voltage (V)
Dropout Voltage (V)
1.2
0.9
0.6
0.3
0.9
0.6
-40C
25C
105C
0.3
0
0
0
0.5
1
1.5
2
Output Current (A)
2.5
3
3.5
0
0.5
VOUT = 3.3 V
2.5
3
3.5
D019
Figure 46. Dropout for ≥ 1.85 MHz
5E+6
2.5
2E+6
1E+6
5E+5
2.25
Switching Frequency (MHz)
Switching Frequency (Hz)
1.5
2
Output Current (A)
VOUT = 3.3 V
Figure 45. Dropout for –3% Regulation
2E+5
1E+5
5E+4
2E+4
1E+4
5E+3
2E+3
1E+3
5E+2
2E+2
1E+2
5E+1
1E-6
1
D020
8 Vin
12 Vin
18 Vin
2
1.75
1.5
1.25
1
0.75
0.5
0.25
0
1E-5
0.0001 0.001
0.01
Output Current (A)
VOUT = 3.3 V
0.1
0.5
23 5
0
4
8
12
D036
AUTO
VOUT = 3.3 V
Figure 47. Switching Frequency vs Load Current
16
20
24
Input Voltage (V)
28
FPWM
32
36
40
D012
IOUT = 1 A
Figure 48. Switching Frequency vs Input Voltage
5
Output Current (A)
4.5
4
3.5
LM53635
LM53625
3
5
10
VOUT = 3.3 V
15
20
25
Input Voltage (V)
L=2.2 µH
30
35
40
D005
IOUT = 1 A
Figure 49. Output Current Level for Overcurrent Protection
Trip
36
Submit Documentation Feedback
AUTO
COUT = 3 × 22 µF
VOUT = 3.3 V
IOUT = 0 A to 3.5 A
L = 2.2 µH,
TR = TF = 1 µs
Figure 50. Load Transient
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
FPWM
COUT = 3 × 22 µF
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
VOUT = 3.3 V
IOUT = 0 A to 3.5 A
L = 2.2 µH,
TR = TF = 1 µs
Figure 51. Load Transient
VOUT = 3.3 V
VOUT = 3.3 V
IOUT = 10 mA
Figure 52. Mode Change Transient AUTO to FPWM mode
IOUT = 10 mA
Figure 53. Mode Change Transient FPWM to AUTO Mode
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
37
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
9.2.4 Adjustable Output
Figure 54. 6 V Output Power Supply
38
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
9.2.4.1 Design Requirements
The application highlighted in this section is for a typical 6-V system but can be used as a basis for the
implementation of the adjustable version of the LM53625/LM53635 for other output voltages as well. The input
voltages are here for illustration purposes only. See Electrical Characteristics for minimum operating input
voltage.
Table 10. Example Requirements for 6-V Application
DESIGN PARAMETER
EXAMPLE VALUE
Input voltage range
8-V to 18-V steady state
Output current
0 A to 3.5 A
Swtiching Frequency at 0-A load
Constant frequency preferred
Current Consumption at 0-A load
Not critical
Synchronization
No
9.2.4.2 Detailed Design Procedure
• BIAS is connected to the output. This example assumes that inductive short are a risk for this application so a
3-Ω resistor is added between BIAS and the output. A 0.1-µF capacitor is added close the BIAS pin.
• FB is connected to the output through a voltage divider in order to create a voltage of 1 V at the FB pin when
the output is at 6 V. A 12-pF capacitance is added in parallel with the top feedback resistor in order to
improve transient behavior. BIAS and FB are connected to the output via separate traces. This is important to
reduce noise and achieve good performances. See Layout Guidelines for more details on the proper layout
method.
• SYNC is connected to ground directly as there is no need for this function in this application.
• EN is toggled by an external device (like an MCU for example). A pulldown resistor is placed to ensure the
part does not turn on if the external source is not driving the pin (Hi-Z condition).
• FPWM is connected to GND. This leads the device to operate in AUTO mode. In this mode, the switching
frequency is adjusted at light loads to keep efficiency maximum. As a result the switching frequency changes
with the output current until medium load is reached. The device then switches at the frequency defined by
FSW. See Device Functional Modes for more details.
• A 4.7-µF capacitor is connected between VCC and GND close to the VCC pin. This ensure stable operation
of the internal LDO.
• RESET is not used in this example so the pin has been left floating. Other possible connections can be seen
in the previous typical applications and in RESET Flag Output.
• Power components (input capacitor, output capacitor, and inductor) selection can be found here in External
Components Selection.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
39
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
9.2.4.3 Application Curves
The following characteristics apply only to the circuit of Figure 54. These parameters are not tested and
represent typical performance only. Unless otherwise stated, the following conditions apply: VIN = 12 V, TA =
25°C. For the purpose of offering meaningful information to the designer, information is included for the
application with FPWM pin high (FPWM mode) and FPWM pin low (AUTO mode) although the schematic shows
the application running specifically in AUTO mode. The mode is specified under each of the following graphs.
2.5E+6
Switching Frequency (Hz)
2.25E+6
2E+6
1.75E+6
1.5E+6
1.25E+6
1E+6
7.5E+5
5E+5
2.5E+5
0
0
4
8
VOUT = 6 V (ADJ part)
12
16
20
24
Input Voltage (V)
FPWM
28
32
36
40
D037
IOUT = 0 A
Figure 55. Switching Frequency vs Input Voltage
VOUT = 6 V (ADJ part)
FPWM
IOUT = 0 A
Figure 57. Start-up Waveform (EN tied to VIN)
40
Submit Documentation Feedback
VOUT = 6 V (ADJ part)
FPWM
IOUT = 0 A
Figure 56. Start-up Waveform
VOUT = 6 V (ADJ part)
FPWM
Figure 58. Load Transient
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
9.3 Do's and Don't's
•
•
•
•
•
•
•
Don't: Exceed the Absolute Maximum Ratings.
Don't: Exceed the Recommended Operating Conditions.
Don't: Allow the EN, FPWM or SYNC input to float.
Don't: Allow the output voltage to exceed the input voltage, nor go below ground.
Don't: Use the thermal data given in the Thermal Information table to design your application.
Do: Follow all of the guidelines and/or suggestions found in this data sheet before committing a design to
production. TI Application Engineers are ready to help critique designs and PCB layouts to help ensure
successful projects.
Do: Refer to the helpful documents found in Related Documentation.
10 Power Supply Recommendations
The characteristics of the input supply must be compatible with the Absolute Maximum Ratings and
Recommended Operating Conditions found in this data sheet. In addition, the input supply must be capable of
delivering the required input current to the loaded regulator. The average input current can be estimated with
Equation 6:
VOUT ˜ IOUT
VIN ˜ K
IIN
where
•
η is the efficiency.
(6)
If the regulator is connected to the input supply through long wires or PCB traces, special care is required to
achieve good performance. The parasitic inductance and resistance of the input cables can have an adverse
effect on the operation of the regulator. The parasitic inductance, in combination with the low ESR ceramic input
capacitors, can form an under-damped resonant circuit. This circuit may cause overvoltage transients at the VIN
pin, each time the input supply is cycled on and off. The parasitic resistance causes the voltage at the VIN pin to
dip when the load on the regulator is switched on or exhibits a transient. If the regulator is operating close to the
minimum input voltage, this dip may cause the device to shut down and/or reset. The best way to solve these
kinds of issues is to reduce the distance from the input supply to the regulator and/or use an aluminum or
tantalum input capacitor in parallel with the ceramics. The moderate ESR of these types of capacitors helps to
damp the input resonant circuit and reduce any voltage overshoots. A value in the range of 20 µF to 100 µF is
usually sufficient to provide input damping and help to hold the input voltage steady during large load transients.
Sometimes, for other system considerations, an input filter is used in front of the regulator. This can lead to
instability, as well as some of the effects mentioned above, unless it is designed carefully. SNVA489 provides
helpful suggestions when designing an input filter for any switching regulator.
In some cases a transient voltage suppressor (TVS) is used on the input of regulators. One class of this device
has a snap-back V-I characteristic (thyristor type). The use of a device with this type of characteristic is not
recommend. When the TVS fires, the clamping voltage drops to a very low value. If this holding voltage is less
than the output voltage of the regulator, the output capacitors are discharged through the regulator back to the
input. This uncontrolled current flow could damage the regulator.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
41
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
11 Layout
11.1 Layout Guidelines
The PCB layout of a DC-DC converter is critical for optimal performance of the application. For a buck converter
the input loop formed by the input capacitors and power grounds are very critical. The input loop carries fast
transient currents that cause larger transient voltages when reacting with a parasitic loop inductance. The IC
uses two input loops in parallel IN1 and IN2 as shown in Figure 59 that cuts the parasitic input inductance in half.
To get the minimum input loop area two small high frequency capacitors CIN1 and CIN2 are placed as close as
possible.
To further reduce inductance, an input current return path should be placed underneath the loops IN1 and IN2.
The closest metal plane is MID1 Layer2, and with a solid copper plane placed right under the IN1 and IN2 loop
the parasitic loop inductance is minimized. Connecting this MID1 Layer2 plane then to GND will provide a nice
bridge connection between GND1 and GND2 as well. Minimizing the parasitic input loop inductance will minimize
switch node ringing and EMI.
The output current loop can be optimized as well by using two ceramic output caps COUT1 and COUT2 to each
side. They will form two parallel ground return paths OUT1 from COUT1 back to the low side FET PGND1 pins
5,6,7,8 and a second symmetric ground return path OUT2 from COUT2 back to low side FET PGND2 pins
10,11,12 and 13. Having two parallel ground return path will yield into reduced “ground bouncing” and reduced
sensitivity of surrounding circuits sensitive to it.
Figure 59. Layout of the Power Components and Current Flow
42
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
Layout Guidelines (continued)
Providing adequate thermal paths to dissipate heat is critical for operation at full current. The recommended
method for heat dissipation is to use large solid 2 oz copper planes well connected to the power pins VIN1, VIN2,
GND1 and GND2 which transfer the heat out of the IC over the TOP Layer1 copper planes. It is important to
leave the TOP Layer1 copper planes as unbroken as much as possible so that heat is not trapped near the IC.
The heat flow can be further optimized by thermally connecting the TOP Layer 1 plane to large BOTTOM Layer4
2oz. copper planes with vias. MID2 Layer3 is then open for all other signal routing. A fully filled / solid BOTTOM
Layer4 ground plane without any interruptions or ground splitting is beneficial for EMI as well. Most important for
low EMI is to use the smallest possible switch node copper area. The switch node including the CBOOT cap has
the largest dv/dt signal causing common mode noise coupling. Using any kind of grounded shield around the
switch node will “shorten” and reduce this e-field.
All these DC/DC converter descriptions can be transformed into layout guidelines:
1. Place two 0.047-µF / 50-V high frequency input capacitors CIN1 and CIN2 as close as possible to the VIN1/2
and PGND1/2 pins to minimize switch node ringing.
2. Place bypass capacitors for VCC and BIAS close to their respective pins. Make sure AGND pin “sees” the
CVCC and CBIAS capacitors first before connecting it to GND.
3. Place CBOOT capacitor with smallest parasitic loop. Shielding the CBOOT capacitor and switch node will have
biggest impact to reduce common mode noise. Placing a small RBOOT resistor (less than 3 Ω is
recommended) in series to CBOOT will slow down the dV/dt of the switch node and reduce EMI.
4. Place the feedback resistor divider for adjustable parts as close as possible to the FB pin and to AGND pin
of the device. Use dedicated feedback trace and away from switch node and CBOOT capacitor to avoid any
cross coupling into sensitive analog feedback.
5. Use dedicated BIAS trace to avoid noise into feedback trace.
6. Use a 3-Ω to 5-Ω resistor between the output and BIAS if the load is far from the output of the converter or
inductive shorts on the output are possible.
7. Use well connected large 2-oz. TOP and BOTTOM copper planes for all power pins VIN1/2 and PGND1/2.
8. Minimize switch node and CBOOT area for lowest EMI common mode noise.
9. For lowest EMI place input and output wires on same side of PCB, using EMI filter and away from switch
node.
10. The resources in Device and Documentation Support provide additional important guidelines.
11.2 Layout Example
This example layout is the one used in REV A of the LM53635 EVM. It shows the CIN and CIN_HF capacitors
placed symmetrically either side of the device.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
43
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
Layout Example (continued)
Figure 60. Recommended Layout for LM53625/35-Q1
44
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
LM53625-Q1, LM53635-Q1
www.ti.com
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
12 Device and Documentation Support
12.1 Device Support
12.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
12.2 Documentation Support
12.2.1 Related Documentation
For additional information, see the following:
• Optimizing Transient Response of Internally Compensated dc-dc Converters With Feedforward Capacitor
(SLVA289)
• Output Ripple Voltage for Buck Switching Regulator (SLVA630)
• AN-1149 Layout Guidelines for Switching Power Supplies (SNVA021)
• AN-1229 Simple Switcher® PCB Layout Guidelines (SNVA054 )
• Constructing Your Power Supply- Layout Considerations (SLUP230)
• AN-2020 Thermal Design By Insight, Not Hindsight (SNVA419)
• Semiconductor and IC Package Thermal Metrics (SPRA953)
12.3 Related Links
Table 11 lists quick access links. Categories include technical documents, support and community resources,
tools and software, and quick access to sample or buy.
Table 11. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
LM53625-Q1
Click here
Click here
Click here
Click here
Click here
LM53635-Q1
Click here
Click here
Click here
Click here
Click here
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
Submit Documentation Feedback
45
LM53625-Q1, LM53635-Q1
SNVSAA7A – DECEMBER 2015 – REVISED MAY 2016
www.ti.com
12.4 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.5 Trademarks
E2E is a trademark of Texas Instruments.
WEBENCH is a registered trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.6 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
46
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM53625-Q1 LM53635-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jul-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM536253QRNLRQ1
ACTIVE
VQFN-HR
RNL
22
3000
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L536253
LM536253QRNLTQ1
ACTIVE
VQFN-HR
RNL
22
250
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L536253
LM536255QRNLRQ1
PREVIEW
VQFN-HR
RNL
22
3000
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L536255
LM536255QRNLTQ1
PREVIEW
VQFN-HR
RNL
22
250
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L536255
LM53625AQRNLRQ1
PREVIEW
VQFN-HR
RNL
22
3000
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L53625A
LM53625AQRNLTQ1
PREVIEW
VQFN-HR
RNL
22
250
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L53625A
LM53625LQRNLRQ1
ACTIVE
VQFN-HR
RNL
22
3000
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L53625L
LM53625LQRNLTQ1
ACTIVE
VQFN-HR
RNL
22
250
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L53625L
LM53625MQRNLRQ1
ACTIVE
VQFN-HR
RNL
22
3000
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L53625M
LM53625MQRNLTQ1
ACTIVE
VQFN-HR
RNL
22
250
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L53625M
LM53625NQRNLRQ1
PREVIEW
VQFN-HR
RNL
22
3000
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L53625N
LM53625NQRNLTQ1
PREVIEW
VQFN-HR
RNL
22
250
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L53625N
LM536353QRNLRQ1
ACTIVE
VQFN-HR
RNL
22
3000
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L536353
LM536353QRNLTQ1
ACTIVE
VQFN-HR
RNL
22
250
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L536353
LM536355QRNLRQ1
ACTIVE
VQFN-HR
RNL
22
3000
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L536355
LM536355QRNLTQ1
ACTIVE
VQFN-HR
RNL
22
250
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L536355
LM53635AQRNLRQ1
PREVIEW
VQFN-HR
RNL
22
3000
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L53635A
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
10-Jul-2016
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM53635AQRNLTQ1
PREVIEW
VQFN-HR
RNL
22
250
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L53635A
LM53635LQRNLRQ1
ACTIVE
VQFN-HR
RNL
22
3000
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L53635L
LM53635LQRNLTQ1
ACTIVE
VQFN-HR
RNL
22
250
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L53635L
LM53635MQRNLRQ1
ACTIVE
VQFN-HR
RNL
22
3000
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L53635M
LM53635MQRNLTQ1
ACTIVE
VQFN-HR
RNL
22
250
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L53635M
LM53635NQRNLRQ1
ACTIVE
VQFN-HR
RNL
22
3000
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L53635N
LM53635NQRNLTQ1
ACTIVE
VQFN-HR
RNL
22
250
Pb-Free
(RoHS)
CU SN
Level-2-260C-1 YEAR
-40 to 150
L53635N
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jul-2016
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Jul-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM536253QRNLTQ1
VQFNHR
RNL
22
250
180.0
12.4
4.3
5.3
1.3
8.0
12.0
Q1
LM53625LQRNLTQ1
VQFNHR
RNL
22
250
180.0
12.4
4.3
5.3
1.3
8.0
12.0
Q1
LM53625MQRNLTQ1
VQFNHR
RNL
22
250
180.0
12.4
4.3
5.3
1.3
8.0
12.0
Q1
LM536353QRNLTQ1
VQFNHR
RNL
22
250
180.0
12.4
4.3
5.3
1.3
8.0
12.0
Q1
LM536355QRNLTQ1
VQFNHR
RNL
22
250
180.0
12.4
4.3
5.3
1.3
8.0
12.0
Q1
LM53635LQRNLTQ1
VQFNHR
RNL
22
250
180.0
12.4
4.3
5.3
1.3
8.0
12.0
Q1
LM53635MQRNLTQ1
VQFNHR
RNL
22
250
180.0
12.4
4.3
5.3
1.3
8.0
12.0
Q1
LM53635NQRNLTQ1
VQFNHR
RNL
22
250
180.0
12.4
4.3
5.3
1.3
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Jul-2016
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM536253QRNLTQ1
VQFN-HR
RNL
22
250
195.0
200.0
45.0
LM53625LQRNLTQ1
VQFN-HR
RNL
22
250
195.0
200.0
45.0
LM53625MQRNLTQ1
VQFN-HR
RNL
22
250
195.0
200.0
45.0
LM536353QRNLTQ1
VQFN-HR
RNL
22
250
195.0
200.0
45.0
LM536355QRNLTQ1
VQFN-HR
RNL
22
250
195.0
200.0
45.0
LM53635LQRNLTQ1
VQFN-HR
RNL
22
250
195.0
200.0
45.0
LM53635MQRNLTQ1
VQFN-HR
RNL
22
250
195.0
200.0
45.0
LM53635NQRNLTQ1
VQFN-HR
RNL
22
250
195.0
200.0
45.0
Pack Materials-Page 2
PACKAGE OUTLINE
RNL0022A
VQFN - 0.9 mm max height
SCALE 2.800
PLASTIC QUAD FLATPACK - NO LEAD
4.1
3.9
B
A
PIN 1 INDEX AREA
5.1
4.9
(0.08)
(0.05)
SECTION A-A
SECTION A-A
SCALE 30.000
TYPICAL
C
0.9 MAX
SEATING PLANE
0.05
0.00
0.08 C
2
1
2X 0.8 0.1
9
8
8X 0.5
2X
2.175
5X
10
7
(0.2) TYP
11
2X
1.45 0.1
2X
0.25
2.95±0.1
4
2X
2
0.45
0.35
PKG
14
15X
2X 0.85
5X
A
0.65
0.45
A
0.3
0.2
0.1
0.05
C A
C
B
17
1
2X 0.575
0.45
0.35
0.5
0.3
22
SYMM
0.45
0.35
18
11X
2
0.5
0.3
4221861/B 04/2016
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
www.ti.com
EXAMPLE BOARD LAYOUT
RNL0022A
VQFN - 0.9 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
4X (0.5)
SYMM
15X (0.25)
18
22
12X (0.6)
2X (0.4)
(2.325)
1
17
2X (2)
5X (0.75)
2X (1.425)
3X (0.4)
2X (0.575)
2X (1)
0.000 PKG
2X (0.25)
4
2X (0.4)
14
(0.295)
( 0.2) VIA TYP
NOTE 4
(3.15)
(1.125)
2X (1.65)
2X (1.875)
(2.175)
4X (0.5)
(1.955)
11
7
9
8
10
(2)
(3.4)
6X (3.8)
LAND PATTERN EXAMPLE
SCALE:20X
0.05 MIN
ALL AROUND
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
SOLDER MASK DEFINED
ALL PADS
4221861/B 04/2016
NOTES: (continued)
3. This package is designed to be soldered to thermal pads on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
4. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown
on this view. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
RNL0022A
VQFN - 0.9 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
15X (0.25)
4X (0.5)
SYMM
22
18
5X (0.75)
12X (0.6)
2X (0.4)
(2.325)
1
2X (2)
17
(R0.05) TYP
2X (1.425)
6X
EXPOSED
METAL
2X (0.575)
7X
EXPOSED
METAL
(1.4)
(0.12)
0.000 PKG
(0.25)
4X ( 0.4)
4
14
SOLDER MASK EDGE
TYP
(0.71)
(2)
2X (1.445)
(1.54)
4X (0.5)
2X (2.175)
2X (2.305)
11
4X
(0.66)
7
8
8X (0.4)
(2.37)
9
10
4X (0.63)
(2)
(3.8)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
FOR PADS 4,8,9,10 & 14
80% PRINTED SOLDER COVERAGE BY AREA
SCALE:25X
4221861/B 04/2016
NOTES: (continued)
5. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
Similar pages