AD AD9142BCPZ Dual, 16-bit, 1600 msps, txdac digital-to-analog converter Datasheet

Dual, 16-Bit, 1600 MSPS, TxDAC+
Digital-to-Analog Converter
AD9142
Data Sheet
FEATURES
GENERAL DESCRIPTION
Very small inherent latency variation: <2 DAC clock cycles
Proprietary low spurious and distortion design
6-carrier GSM ACLR = 79 dBc at 200 MHz IF
SFDR > 85 dBc (bandwidth = 300 MHz) at ZIF
Flexible 16-bit LVDS interface
Supports word and byte load
Multiple chip synchronization
Fixed latency and data generator latency compensation
Selectable 2×, 4×, 8× interpolation filter
Low power architecture
fS/4 power saving coarse mixer
Input signal power detection
Emergency stop for downstream analog circuitry
protection
FIFO error detection
On-chip numeric control oscillator allows carrier placement
anywhere in the DAC Nyquist bandwidth
Transmit enable function for extra power saving
High performance, low noise PLL clock multiplier
Digital gain and phase adjustment for sideband suppression
Digital inverse sinc filter
Supports single DAC mode
Low power: 2.0 W at 1.6 GSPS, 1.7 W at 1.25 GSPS, full
operating conditions
72-lead LFCSP
The AD9142 is a dual, 16-bit, high dynamic range digital-toanalog converter (DAC) that provides a sample rate of 1600 MSPS,
permitting a multicarrier generation up to the Nyquist frequency.
The AD9142 TxDAC+® includes features optimized for direct
conversion transmit applications, including complex digital modulation, input signal power detection, and gain, phase, and offset
compensation. The DAC outputs are optimized to interface
seamlessly with analog quadrature modulators, such as the
ADL537x F-MOD series and the ADRF670x series from Analog
Devices, Inc. A 3-wire serial port interface provides for the programming/readback of many internal parameters. Full-scale
output current can be programmed over a range of 9 mA to 33 mA.
The AD9142 is available in a 72-lead LFCSP.
1.
2.
3.
4.
5.
APPLICATIONS
Wireless communications: 3G/4G and MC-GSM base stations,
wideband repeaters, software defined radios
Wideband communications: point-to-point, LMDS/MMDS
Transmit diversity/MIMO
Instrumentation
Automated test equipment
Rev. 0
PRODUCT HIGHLIGHTS
Advanced low spurious and distortion design techniques
provide high quality synthesis of wideband signals from
baseband to high intermediate frequencies.
Very small inherent latency variation simplifies both software
and hardware design in the system. It allows easy multichip
synchronization for most applications.
New low power architecture improves power efficiency
(mW/MHz/channel) by 30%.
Input signal power and FIFO error detection simplify
designs for downstream analog circuitry protection.
Programmable transmit enable function allows easy design
balance between power consumption and wakeup time.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
©2012 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD9142
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Input Signal Power Detection and Protection ........................ 30
Applications ....................................................................................... 1
Transmit Enable Function ......................................................... 31
General Description ......................................................................... 1
Digital Function Configuration ............................................... 31
Product Highlights ........................................................................... 1
Multidevice Synchronization and Fixed Latency ....................... 32
Revision History ............................................................................... 3
Very Small Inherent Latency Variation ................................... 32
Functional Block Diagram .............................................................. 4
Further Reducing the Latency Variation ................................. 32
Specifications..................................................................................... 5
Synchronization Implementation ............................................ 33
DC Specifications ......................................................................... 5
Synchronization Procedures ..................................................... 33
Digital Specifications ................................................................... 6
Interrupt Request Operation ........................................................ 34
DAC Latency Specifications ........................................................ 7
Interrupt Working Mechanism ................................................ 34
Latency Variation Specifications ................................................ 7
Interrupt Service Routine .......................................................... 34
AC Specifications.......................................................................... 7
Temperature Sensor ....................................................................... 35
Operating Speed Specifications .................................................. 8
DAC Input Clock Configurations ................................................ 36
Absolute Maximum Ratings ....................................................... 9
Driving the DACCLK and REFCLK Inputs ........................... 36
Thermal Resistance ...................................................................... 9
Direct Clocking .......................................................................... 36
ESD Caution .................................................................................. 9
Clock Multiplication .................................................................. 36
Pin Configuration and Function Descriptions ........................... 10
PLL Settings ................................................................................ 37
Typical Performance Characteristics ........................................... 12
Configuring the VCO Tuning Band ........................................ 37
Terminology .................................................................................... 17
Automatic VCO Band Select .................................................... 37
Serial Port Operation ..................................................................... 18
Manual VCO Band Select ......................................................... 37
Data Format ................................................................................ 18
Analog Outputs............................................................................... 38
Serial Port Pin Descriptions ...................................................... 18
Transmit DAC Operation.......................................................... 38
Serial Port Options ..................................................................... 18
Interfacing to Modulators ......................................................... 39
Data Interface .................................................................................. 20
Reducing LO Leakage and Unwanted Sidebands .................. 40
LVDS Input Data Ports .............................................................. 20
Example Start-Up Routine ............................................................ 41
Word Interface Mode ................................................................. 20
Device Configuration Register Map and Description ............... 42
Byte Interface Mode ................................................................... 20
SPI Configure Register .............................................................. 44
Data Interface Configuration Options .................................... 20
Power-Down Control Register ................................................. 44
Interface Delay Line ................................................................... 22
Interrupt Enable0 Register ........................................................ 44
FIFO Operation .............................................................................. 23
Interrupt Enable1 Register ........................................................ 44
Resetting the FIFO ..................................................................... 24
Interrupt Flag0 Register............................................................. 45
Serial Port Initiated FIFO Reset ............................................... 24
Interrupt Flag1 Register............................................................. 45
Frame Initiated FIFO Reset....................................................... 24
Interrupt Select0 Register .......................................................... 45
Digital Datapath.............................................................................. 26
Interrupt Select1 Register .......................................................... 46
Interpolation Filters ................................................................... 26
DAC Clock Receiver Control Register .................................... 46
Digital Modulation ..................................................................... 28
Ref Clock Receiver Control Register ....................................... 46
Datapath Configuration ............................................................ 29
PLL Control Register ................................................................. 47
Digital Quadrature Gain and Phase Adjustment ................... 29
PLL Control Register ................................................................. 47
DC Offset Adjustment ............................................................... 29
PLL Control Register ................................................................. 47
Inverse Sinc Filter ....................................................................... 30
PLL Status Register..................................................................... 48
Rev. 0 | Page 2 of 64
Data Sheet
AD9142
PLL Status Register .....................................................................48
NCO_PHASE_OFFSET1 Register............................................ 55
IDAC FS Adjust LSB Register ....................................................48
IQ_PHASE_ADJ0 Register ........................................................ 55
IDAC FS Adjust MSB Register ..................................................48
IQ_PHASE_ADJ1 Register ........................................................ 55
QDAC FS Adjust LSB Register ..................................................48
IDAC_DC_OFFSET0 Register.................................................. 55
QDAC FS Adjust MSB Register ................................................49
IDAC_DC_OFFSET1 Register.................................................. 55
Die Temperature Sensor Control Register ...............................49
QDAC_DC_OFFSET0 Register ................................................ 55
Die Temperature LSB Register ..................................................49
QDAC_DC_OFFSET1 Register ................................................ 56
Die Temperature MSB Register .................................................49
IDAC_GAIN_ADJ Register....................................................... 56
Chip ID Register..........................................................................49
QDAC_GAIN_ADJ Register ..................................................... 56
Interrupt Configuation Register ...............................................50
Gain Step Control0 Register ...................................................... 56
Sync CTRL Register ....................................................................50
Gain Step Control1 Register ...................................................... 56
Frame Reset CTRL Register.......................................................50
TX Enable Control Register ...................................................... 57
FIFO Level Configuration Register ..........................................51
DAC Output Control Register .................................................. 57
FIFO Level Readback Register ..................................................51
Data Receiver Test Control Register......................................... 57
FIFO CTRL Register ...................................................................51
Data Receiver Test Control Register......................................... 57
Data Format Select Register.......................................................52
Device Configuration0 Register................................................ 58
Datapath Control Register .........................................................52
Version Register .......................................................................... 58
Interpolation Control Register ..................................................52
Device Configuration1 Register................................................ 58
Over Threshold CTRL0 Register ..............................................53
Device Configuration2 Register................................................ 58
Over Threshold CTRL1 Register ..............................................53
DAC Latency and System Skews ................................................... 59
Over Threshold CTRL2 Register ..............................................53
DAC Latency Variations............................................................. 59
Input Power Readback LSB Register ........................................53
FIFO Latency Variation.............................................................. 59
Input Power Readback MSB Register .......................................53
Clock Generation Latency Variation ........................................ 60
NCO Control Register ................................................................54
Correcting System Skews ........................................................... 60
NCO_FREQ_TUNING_WORD0 Register.............................54
Packaging and Ordering Information .......................................... 61
NCO_FREQ_TUNING_WORD1 Register.............................54
Outline Dimensions.................................................................... 61
NCO_FREQ_TUNING_WORD2 Register.............................54
Ordering Guide ........................................................................... 61
NCO_FREQ_TUNING_WORD3 Register.............................54
NCO_PHASE_OFFSET0 Register ............................................54
REVISION HISTORY
11/12—Revision 0: Initial Version
Rev. 0 | Page 3 of 64
AD9142
Data Sheet
FUNCTIONAL BLOCK DIAGRAM
INPUT POWER
DETECTION
fDAC /4
MOD
DAC 1
16-BIT
IOUT1P
IOUT1N
DAC CLK
16
DAC 2
16-BIT
IOUT2P
GAIN 1
10
GAIN 2
IOUT2N
DAC_CLK
INTERP
MODE CTRL3
INTERP
MODE CTRL2
INTERP
MODE CTRL1
FIFO CTRL
INTERFACE CTRL
FRAMEP/
FRAMEN
16
OVER-THRESHOLD
PROTECTION
FIFO
8-SAMPLE
LVDS DATA
RECEIVER
D0P/D0N
NCO
HB3
2×
HB2
2×
HB1
2×
DC OFFSET
CONTROL
COMPLEX
MODULATION
D15P/D15N
GAIN AND PHSE
CONTROL
AD9142
INV
SINC
DCIP/DCIN
10
REF
AND
BIAS
REFIO
FSADJ
INTERNAL CLOCK TIMING AND CONTROL LOGIC
SERIAL
INPUT/OUTPUT
PORT
POWER-ON
RESET
MULTICHIP
SYNCHRONIZATION
DAC_CLK
CLOCK
MULTIPLIER
CLK
RCVR
DACCLKP
DACCLKN
REF
RCVR
REFP/SYNCP
REFN/SYNCN
10930-001
RESET
TXEN
IRQ2
IRQ1
CS
SCLK
SYNC
SDIO
PROGRAMMING
REGISTERS
Figure 1.
Rev. 0 | Page 4 of 64
Data Sheet
AD9142
SPECIFICATIONS
DC SPECIFICATIONS
TMIN to TMAX, AVDD33 = 3.3 V, DVDD18 = 1.8 V, CVDD18 = 1.8 V, IOUTFS = 20 mA, maximum sample rate, unless otherwise noted.
Table 1.
Parameter
RESOLUTION
ACCURACY
Differential Nonlinearity (DNL)
Integral Nonlinearity (INL)
MAIN DAC OUTPUTS
Offset Error
Gain Error
Full-Scale Output Current
Output Compliance Range
Output Resistance
Gain DAC Monotonicity
Settling Time to Within ±0.5 LSB
MAIN DAC TEMPERATURE DRIFT
Offset
Gain
Reference Voltage
REFERENCE
Internal Reference Voltage
Output Resistance
ANALOG SUPPLY VOLTAGES
AVDD33
CVDD18
DIGITAL SUPPLY VOLTAGES
DVDD18
POWER CONSUMPTION
2× Mode
NCO OFF
NCO ON
4× Mode
NCO OFF
NCO ON
4× Mode
NCO OFF
NCO ON
8× Mode
NCO OFF
NCO ON
Phase-Lock Loop
Inverse Sinc
Reduced Power Mode (Power Down)
AVDD33
CVDD18
DVDD18
OPERATING RANGE
Test Conditions/Comments
Min
Typ
16
Max
±2.1
±3.7
With internal reference
Based on a 10 kΩ external resistor between FSADJ and AVSS
−0.001
−3.2
19.06
−1.0
0
2
19.8
Unit
Bits
LSB
LSB
+0.001
4.7
+20.6
+1.0
% FSR
% FSR
mA
V
MΩ
10
Guaranteed
20
ns
0.04
100
30
ppm/°C
ppm/°C
ppm/°C
1.17
1.19
V
kΩ
5
3.13
1.71
3.3
1.8
3.47
1.89
V
V
1.71
1.8
1.89
V
fDAC = 491.52 MSPS
700
870
mW
mW
836
1085
mW
mW
1030
1365
mW
mW
1315
1815
70
113
mW
mW
mW
mW
mW
mA
mA
mA
°C
fDAC = 737.28 MSPS
fDAC = 983.04 MSPS
fDAC = 1600 MSPS
fDAC = 1474.56 MSPS
−40
Rev. 0 | Page 5 of 64
+25
96.6
1.5
42.3
8.6
+85
AD9142
Data Sheet
DIGITAL SPECIFICATIONS
TMIN to TMAX, AVDD33 = 3.3 V, DVDD18 = 1.8 V, CVDD18 = 1.8 V, IOUTFS = 20 mA, maximum sample rate, unless otherwise noted.
Table 2.
Parameter
CMOS INPUT LOGIC LEVEL
Input
Logic High
Logic Low
CMOS OUTPUT LOGIC LEVEL
Output
Logic High
Logic Low
LVDS RECEIVER INPUTS
Input Voltage Range
Input Differential Threshold
Symbol
Input Differential Hysteresis
Receiver Differential Input Impedance
DAC UPDATE RATE
DAC Adjusted Update Rate
DAC CLOCK INPUT (DACCLKP, DACCLKN)
Differential Peak-to-Peak Voltage
Common-Mode Voltage
REFCLK/SYNCCLK INPUT (REFP/SYNCP, REFN/SYNCN)
Differential Peak-to-Peak Voltage
Common-Mode Voltage
Input Clock Frequency
SERIAL PORT INTERFACE
Maximum Clock Rate
Minimum Pulse Width
High
Low
Setup Time
Hold Time
Setup Time
VIDTHH to VIDTHL
RIN
VIA or VIB
VIDTH
Test Conditions/Comments
Min
DVDD18 = 1.8 V
DVDD18 = 1.8 V
1.2
DVDD18 = 1.8 V
DVDD18 = 1.8 V
1.4
Data and FRAME inputs
DCI input
Typ
825
−100
−225
Unit
0.6
V
V
0.4
V
V
1675
+100
+225
20
120
1600
250
2× interpolation
500
1.25
2000
mV
V
100
500
1.25
2000
mV
V
MHz
1 GHz ≤ fVCO ≤ 2.1 GHz
SCLK
450
40
MHz
12.5
12.5
SDIO to SCLK
SDIO to SCLK
CS to SCLK
Rev. 0 | Page 6 of 64
mV
mV
mV
mV
Ω
MSPS
MSPS
100
Self biased input, ac-coupled
tPWH
tPWL
tDS
tDH
tDCSB
Max
1.5
0.68
2.38
1.4
ns
ns
ns
ns
ns
Data Sheet
AD9142
DAC LATENCY SPECIFICATIONS
TMIN to TMAX, AVDD33 = 3.3 V, DVDD18 = 1.8 V, CVDD18 = 1.8 V, IOUTFS = 20 mA, FIFO level is set to 4 (half of the FIFO depth), unless
otherwise noted.
Table 3.
Parameter
WORD INTERFACE MODE
2× Interpolation
4× Interpolation
8× Interpolation
BYTE INTERFACE MODE
2× Interpolation
4× Interpolation
8× Interpolation
INDIVIDUAL FUNCTION BLOCKS
Modulation
Fine
Coarse
Inverse Sinc
Phase Compensation
Gain Compensation
Test Conditions/Comments
Fine/coarse modulation, inverse sinc, gain/phase compensation off
Min
Typ
Max
Unit
134
244
481
DACCLK cycles
DACCLK cycles
DACCLK cycles
145
271
506
DACCLK cycles
DACCLK cycles
DACCLK cycles
17
10
20
12
16
DACCLK cycles
DACCLK cycles
DACCLK cycles
DACCLK cycles
DACCLK cycles
Fine/coarse modulation, inverse sinc, gain/phase compensation off
LATENCY VARIATION SPECIFICATIONS 1
Table 4.
Parameter
DAC LATENCY VARIATION
SYNC Off
SYNC On
1
Min
Typ
Max
Unit
2
1
DACCLK cycles
DACCLK cycles
DAC latency is defined as the elapsed time from a data sample clocked at the input to the AD9142 until the analog output begins to change.
AC SPECIFICATIONS
TMIN to TMAX, AVDD33 = 3.3 V, DVDD18 = 1.8 V, CVDD18 = 1.8 V, IOUTFS = 20 mA, maximum sample rate, unless otherwise noted.
Table 5.
Parameter
SPURIOUS-FREE DYNAMIC RANGE (SFDR)
fDAC = 737.28 MSPS
BW = 125 MHz
BW = 270 MHz
fDAC = 983.04 MSPS
BW = 360MHz
fDAC = 1228.8 MSPS
BW = 200MHz
BW = 500MHz
fDAC = 1474.56 MSPS
BW = 737MHz
BW = 400MHz
TWO-TONE INTERMODULATION DISTORTION (IMD)
fDAC = 737.28 MSPS
fDAC = 983.04 MSPS
fDAC = 1228.8 MSPS
fDAC = 1474.56 MSPS
Test Conditions/Comments
−14 dBFS single tone
fOUT = 200 MHz
Min
Typ
Max
Unit
85
80
dBc
dBc
85
dBc
85
75
dBc
dBc
85
80
dBc
dBc
80
82
80
85
79
dBc
dBc
dBc
dBc
dBc
fOUT = 200 MHz
fOUT = 280 MHz
fOUT = 10 MHz
fOUT = 280 MHz
−6 dBFS each tone
fOUT = 200 MHz
fOUT = 200 MHz
fOUT = 280 MHz
fOUT = 10 MHz
fOUT = 280 MHz
Rev. 0 | Page 7 of 64
AD9142
Data Sheet
Parameter
NOISE SPECTRAL DENSITY (NSD)
fDAC = 737.28 MSPS
fDAC = 983.04 MSPS
fDAC = 1228.8 MSPS
fDAC = 1474.56 MSPS
W-CDMA ADJACENT CHANNEL LEAKAGE RATIO (ACLR)
fDAC = 983.04 MSPS
fDAC = 1228.8 MSPS
fDAC = 1474.56 MSPS
W-CDMA SECOND (ACLR)
fDAC = 983.04 MSPS
fDAC = 1228.8 MSPS
fDAC = 1474.56 MSPS
Test Conditions/Comments
Eight-tone, 500 kHz tone spacing
fOUT = 200 MHz
fOUT = 200 MHz
fOUT = 280 MHz
fOUT = 10 MHz
fOUT = 280 MHz
Single carrier
fOUT = 200 MHz
fOUT = 20 MHz
fOUT = 280 MHz
fOUT = 20 MHz
fOUT = 280 MHz
Single carrier
fOUT = 200 MHz
fOUT = 20 MHz
fOUT = 280 MHz
fOUT = 20 MHz
fOUT = 280 MHz
Min
Typ
Max
−160
−161.5
−164.5
−166
−162.5
dBm/Hz
dBm/Hz
dBm/Hz
dBm/Hz
dBm/Hz
81
83
80
81
80
dBc
dBc
dBc
dBc
dBc
85
86
86
86
85
dBc
dBc
dBc
dBc
dBc
OPERATING SPEED SPECIFICATIONS
Table 6.
Interpolation
Factor
2×
4×
8×
DVDD18, CVDD18 = 1.8 V ± 5%
fINTERFACE (Mbps) Max
fDAC (Mbps) Max
250
500
250
1000
187.5
1500
DVDD18, CVDD18 = 1.8 V ± 2% or 1.9 V ± 5%
fINTERFACE (Mbps) Max
fDAC (Mbps) Max
250
500
250
1000
200
1600
Rev. 0 | Page 8 of 64
Unit
Data Sheet
AD9142
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 7.
Parameter
AVDD33 to AVSS, EPAD, CVSS, DVSS
DVDD18, CVDD18 to AVSS, EPAD,
CVSS, DVSS
AVSS to EPAD, CVSS, DVSS
EPAD to AVSS, CVSS, DVSS
CVSS to AVSS, EPAD, DVSS
DVSS to AVSS, EPAD, CVSS
FSADJ, REFIO, IOUT1P/IOUT1N,
IOUT2P/IOUT2N to AVSS
D[15:0]P/D[15:0]N, FRAMEP/FRAMEN,
DCIP/DCIN to EPAD, DVSS
DACCLKP/DACCLKN,
REFP/SYNCP/REFN/SYNCN to CVSS
RESET, IRQ1, IRQ2, CS, SCLK, SDIO
to EPAD, DVSS
Junction Temperature
Storage Temperature Range
The exposed pad (EPAD) must be soldered to the ground plane
(AVSS) for the 72-lead LFCSP. The EPAD provides an electrical,
thermal, and mechanical connection to the board.
Rating
−0.3 V to +3.6 V
−0.3 V to +2.1 V
−0.3 V to +0.3 V
−0.3 V to +0.3 V
−0.3 V to +0.3 V
−0.3 V to +0.3 V
−0.3 V to AVDD33 + 0.3 V
−0.3 V to DVDD18 + 0.3 V
Typical θJA, θJB, and θJC values are specified for a 4-layer board in
still air. Airflow increases heat dissipation, effectively reducing
θJA and θJB.
Table 8. Thermal Resistance
Package
72-Lead LFCSP
−0.3 V to CVDD18 + 0.3 V
−0.3 V to DVDD18 + 0.3 V
ESD CAUTION
125°C
−65°C to +150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. 0 | Page 9 of 64
θJA
20.7
θJB
10.9
θJC
1.1
Unit
°C/W
Conditions
EPAD soldered
to ground plane
AD9142
Data Sheet
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
CVDD18
CVDD18
REFIO
FSADJ
AVDD33
IOUT1P
IOUT1N
AVDD33
CVDD18
CVDD18
DACCLKN
DACCLKP
CVDD18
CVDD18
AVDD33
IOUT2N
IOUT2P
AVDD33
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
AD9142
TOP VIEW
(Not to Scale)
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
CS
SCLK
SDIO
IRQ1
IRQ2
DVDD18
DVDD18
D0N
D0P
D1N
D1P
DVDD18
D2N
D2P
D3N
D3P
D4N
D4P
NOTES
1. EXPOSED PAD (EPAD) MUST BE SOLDERED TO THE GROUND
PLANE (AVSS). THE EPAD PROVIDES AN ELECTRICAL, THERMAL,
AND MECHANICAL CONNECTION TO THE BOARD.
2. EPAD IS THE GROUND CONNECTION FOR CVSS AND DVSS.
10930-002
DVDD18
D11P
D11N
D10P
D10N
D9P
D9N
D8P
D8N
DCIP
DCIN
D7P
D7N
D6P
D6N
D5P
D5N
DVDD18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
CVDD18
REFP/SYNCP
REFN/SYNCN
CVDD18
RESET
TXEN
DVDD18
FRAMEP
FRAMEN
D15P
D15N
DVDD18
D14P
D14N
D13P
D13N
D12P
D12N
Figure 2. Pin Configuration
Table 9. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
Mnemonic
CVDD18
REFP/SYNCP
REFN/SYNCN
CVDD18
RESET
TXEN
7
DVDD18
8
9
10
11
12
13
14
15
16
17
18
19
FRAMEP
FRAMEN
D15P
D15N
DVDD18
D14P
D14N
D13P
D13N
D12P
D12N
DVDD18
20
21
22
23
24
D11P
D11N
D10P
D10N
D9P
Description
1.8 V PLL Supply. CVDD18 supplies the clock receivers, clock multiplier, and clock distribution.
PLL Reference Clock Input, Positive.
PLL Reference Clock Input, Negative.
1.8 V PLL Supply. CVDD18 supplies the clock receivers, clock multiplier, and clock distribution.
Reset, Active Low. CMOS levels with respect to DVDD18. Recommended reset pulse length is 1 μs.
Active High Transmit Path Enable. CMOS levels with respect to DVDD18. A low level on this pin triggers three
selectable actions in the DAC. See Register 0x43 in Table 77 for details.
1.8 V Digital Supply. Pin 7 supplies power to the digital core, digital data ports, serial port input/output pins, RESET, IRQ1,
and IRQ2.
Frame Input, Positive.
Frame Input, Negative.
Data Bit 15 (MSB), Positive.
Data Bit 15 (MSB), Negative.
1.8 V Digital Supply. Pin 12 supplies the power to the digital core and digital data ports.
Data Bit 14, Positive.
Data Bit 14, Negative.
Data Bit 13, Positive.
Data Bit 13, Negative.
Data Bit 12, Positive.
Data Bit 12, Negative.
1.8 V Digital Supply. Pin 19 supplies power to the digital core, digital data ports, serial port input/output pins,
RESET, IRQ1, and IRQ2.
Data Bit 11, Positive.
Data Bit 11, Negative.
Data Bit 10, Positive.
Data Bit 10, Negative.
Data Bit 9, Positive.
Rev. 0 | Page 10 of 64
Data Sheet
Pin No.
25
26
27
28
29
30
31
32
33
34
35
36
Mnemonic
D9N
D8P
D8N
DCIP
DCIN
D7P
D7N
D6P
D6N
D5P
D5N
DVDD18
37
38
39
40
41
42
43
D4P
D4N
D3P
D3N
D2P
D2N
DVDD18
44
45
46
47
48
D1P
D1N
D0P
D0N
DVDD18
49
DVDD18
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
IRQ2
IRQ1
SDIO
SCLK
CS
AVDD33
IOUT2P
IOUT2N
AVDD33
CVDD18
CVDD18
DACCLKN
DACCLKP
CVDD18
CVDD18
AVDD33
IOUT1N
IOUT1P
AVDD33
FSADJ
REFIO
CVDD18
CVDD18
EPAD
AD9142
Description
Data Bit 9, Negative.
Data Bit 8, Positive.
Data Bit 8, Negative.
Data Clock Input, Positive.
Data Clock Input, Negative.
Data Bit 7, Positive.
Data Bit 7, Negative.
Data Bit 6, Positive.
Data Bit 6, Negative.
Data Bit 5, Positive.
Data Bit 5, Negative.
1.8 V Digital Supply. Pin 36 supplies power to the digital core, digital data ports, serial port input/output pins,
RESET, IRQ1, and IRQ2.
Data Bit 4, Positive.
Data Bit 4, Negative.
Data Bit 3, Positive.
Data Bit 3, Negative.
Data Bit 2, Positive.
Data Bit 2, Negative.
1.8 V Digital Supply. Pin 43 supplies power to the digital core, digital data ports, serial port input/output pins,
RESET, IRQ1, and IRQ2.
Data Bit 1, Positive.
Data Bit 1, Negative.
Data Bit 0 (LSB), Positive.
Data Bit 0 (LSB), Negative.
1.8 V Digital Supply. Pin 48 supplies power to the digital core, digital data ports, serial port input/output pins,
RESET, IRQ1, and IRQ2.
1.8 V Digital Supply. Pin 49 supplies power to the digital core, digital data ports, serial port input/output
pins, RESET, IRQ1, and IRQ2.
Second Interrupt Request. Open-drain, active low output. Connect an external pull-up to DVDD18 through a 10 kΩ resistor.
First Interrupt Request. Open-drain, active low output. Connect an external pull-up to DVDD18 through a 10 kΩ resistor.
Serial Port Data Input/Output. CMOS levels with respect to DVDD18.
Serial Port Clock Input. CMOS levels with respect to DVDD18.
Serial Port Chip Select. Active low (CMOS levels with respect to DVDD18).
3.3 V Analog Supply.
QDAC Positive Current Output.
QDAC Negative Current Output.
3.3 V Analog Supply.
1.8 V Clock Supply. Supplies clock receivers and clock distribution.
1.8 V Clock Supply. Supplies clock receivers and clock distribution.
DAC Clock Input, Negative.
DAC Clock Input, Positive.
1.8 V Clock Supply. Supplies clock receivers and clock distribution.
1.8 V Clock Supply. Supplies clock receivers and clock distribution.
3.3 V Analog Supply.
IDAC Negative Current Output.
IDAC Positive Current Output.
3.3 V Analog Supply.
Full-Scale Current Output Adjust. Place a 10 kΩ resistor from this pin to AVSS.
Voltage Reference. Nominally 1.2 V output. Decouple REFIO to AVSS.
1.8 V Clock Supply. Pin 71 supplies the clock receivers, clock multiplier, and clock distribution.
1.8 V Clock Supply. Pin 72 supplies the clock receivers, clock multiplier, and clock distribution.
Exposed Pad. The exposed pad (EPAD) must be soldered to the ground plane (AVSS). The EPAD provides an
electrical, thermal, and mechanical connection to the board.
Rev. 0 | Page 11 of 64
AD9142
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
0
–60
fDAC = 737.28MHz
fDAC = 983.04MHz
fDAC = 1228.8MHz
fDAC = 1474.56MHz
–10
–65
IN-BAND SFDR (dBc)
–20
–30
SFDR (dBc)
BW
BW
BW
BW
–40
–50
–60
= 80MHz, –6dBFS
= 80MHz, –12dBFS
= 300MHz, –6dBFS
= 300MHz, –12dBFS
–70
–75
–80
–70
–85
–80
100
200
300
400
500
600
700
800
fOUT (MHz)
10930-003
0
< –85
Figure 3. Single-Tone (0 dBFS) SFDR vs. fOUT in the First Nyquist Zone over fDAC
0
–60
IN-BAND SFDR (dBc)
–40
–50
–60
–70
–80
100
120
140
160
180
200
= 80MHz, –6dBFS
= 80MHz, –12dBFS
= 300MHz, –6dBFS
= 300MHz, –12dBFS
–70
–75
–80
–85
0
100
200
300
400
500
600
700
800
fOUT (MHz)
< –85
10930-005
–100
Figure 4. Single-Tone Second Harmonic vs. fOUT in the First Nyquist Zone
over Digital Back Off, fDAC = 1474.56 MHz
0
–60
BW
BW
BW
BW
–65
IN-BAND SFDR (dBc)
–30
–40
–50
–60
–70
150
200
250
300
Figure 7. Single-Tone SFDR (Excluding 2nd Harmonic) vs. fOUT in 80 MHz and
300 MHz BW, fDAC = 983.04 MHz
0dBFS
–6dBFS
–12dBFS
–16dBFS
–20
100
fOUT (MHz)
0
–10
50
10930-006
–85 MEANS ≤ –85
–90
THIRD HARMONIC (dBc)
80
–80
= 80MHz, –6dBFS
= 80MHz, –12dBFS
= 300MHz, –6dBFS
= 300MHz, –12dBFS
–70
–75
–80
–85
–85 MEANS ≤ –85
–90
0
100
200
300
400
fOUT (MHz)
500
600
700
800
< –85
10930-007
–100
Figure 5. Single-Tone Third Harmonic vs. fOUT in the First Nyquist Zone
over Digital Back Off, fDAC = 1474.56 MHz
0
50
100
150
200
fOUT (MHz)
250
300
350
10930-008
SECOND HARMONIC (dBc)
BW
BW
BW
BW
–65
–30
60
Figure 6. Single-Tone SFDR (Excluding 2nd Harmonic) vs. fOUT in 80 MHz and
300 MHz Bandwidths, fDAC = 737.28 MHz
0dBFS
–6dBFS
–12dBFS
–16dBFS
–20
40
fOUT (MHz)
0
–10
20
10930-004
–85 MEANS ≤ –85
–90
Figure 8. Single-Tone SFDR (Excluding 2nd Harmonic) vs. fOUT in 80 MHz and
300 MHz Bandwidths, fDAC = 1228.8 MHz
Rev. 0 | Page 12 of 64
Data Sheet
–60
BW
BW
BW
BW
0
= 80MHz, –6dBFS
= 80MHz, –12dBFS
= 300MHz, –6dBFS
= 300MHz, –12dBFS
0.6MHz TONE SPACING
16MHz TONE SPACING
35MHz TONE SPACING
–20
–70
–40
IMD (dBc)
IN-BAND SFDR (dBc)
–65
AD9142
–75
–80
–60
–80
–85
–100
0
50
100
150
200
250
300
350
fOUT (MHz)
–120
10930-009
< –85
0
–20
300
400
500
600
700
800
Figure 12. Two-Tone Third IMD vs. fOUT over Tone Spacing,
fDAC = 1474.56 MHz
–152
fDAC = 737.28MHz
fDAC = 983.04MHz
fDAC = 1228.8MHz
fDAC = 1474.56MHz
–10
200
fOUT (MHz)
Figure 9. Single-Tone SFDR (Excluding 2nd Harmonic) vs. fOUT in 80 MHz and
300 MHz Bandwidths, fDAC = 1474.56 MHz
0
100
10930-010
–85 MEANS ≤ –85
fDAC = 737.28MHz
fDAC = 983.04MHz
fDAC = 1228.8MHz
fDAC = 1474.56MHz
–154
–156
NSD (dBm/Hz)
IMD (dBc)
–30
–40
–50
–158
–160
–162
–60
–164
–70
–166
–80
200
300
400
500
600
700
800
fOUT (MHz)
–168
0
300
400
500
600
700
800
800
Figure 13. Single-Tone (0 dBFS) NSD vs. fOUT over fDAC
–152
0dBFS
–6dBFS
–9dBFS
–20
200
fOUT (MHz)
Figure 10. Two-Tone Third IMD vs. fOUT over fDAC
0
100
10930-012
100
10930-014
0
10930-011
–90
0dBFS
–6dBFS
–12dBFS
–16dBFS
–154
–156
NSD (dBm/Hz)
–60
–158
–160
–162
–80
–164
–100
–166
–120
0
100
200
300
400
500
600
700
800
fOUT (MHz)
10930-013
IMD (dBc)
–40
–168
0
100
200
300
400
500
600
700
fOUT (MHz)
Figure 14. Single-Tone NSD vs. fOUT over Digital Back Off,
fDAC = 1474.56 MHz
Figure 11. Two-Tone Third IMD vs. fOUT over Digital Back Off,
fDAC = 1474.56 MHz
Rev. 0 | Page 13 of 64
AD9142
–150
Data Sheet
–60
737.2MHz
983.04MHz
1228.8MHz
1474.56MHz
–152
–154
–65
–156
–70
–158
ACLR (dBc)
NSD (dBm/Hz)
fDAC = 1474.56MHz, PLL OFF, 0dBFS
fDAC = 1474.56MHz, PLL ON, 0dBFS
fDAC = 1228.8MHz, PLL OFF, 0dBFS
fDAC = 1228.8MHz, PLL ON, 0dBFS
–160
–162
–75
–80
–164
–166
–85
0
100
200
300
400
500
600
700
800
fOUT (MHz)
–90
10930-200
–170
0
200
300
400
500
600
700
800
fOUT (MHz)
Figure 18. 1C WCDMA 2nd Adjacent ACLR vs. fOUT, PLL On and Off
Figure 15. 1C WCDMA NSD vs. fOUT, over fDAC
–150
100
10930-101
–168
PLL OFF
PLL ON
–152
–154
NSD (dBm/Hz)
–156
–158
–160
–162
–164
0
100
200
300
400
500
600
700
800
fOUT (MHz)
10930-016
–168
10930-015
–166
Figure 16. Single-Tone NSD vs. fOUT, fDAC = 1474.28 MHz, PLL On and Off
–60
fDAC = 1474.56MHz, PLL OFF, 0dBFS
fDAC = 1474.56MHz, PLL ON, 0dBFS
fDAC = 1228.8MHz, PLL OFF, 0dBFS
fDAC = 1228.8MHz, PLL ON, 0dBFS
–65
–70
–75
–80
0
100
200
300
400
500
600
700
800
fOUT (MHz)
Figure 17. 1C WCDMA 1st Adjacent ACLR vs. fOUT, PLL On and Off
10930-017
–85
10930-100
ACLR (dBc)
Figure 19. Two-Tone Third IMD Performance,
IF = 280 MHz, fDAC = 1474.28 MHz
Figure 20. 1C WCDMA ACLR Performance, IF = 280 MHz, fDAC = 1474.28 MHz
Rev. 0 | Page 14 of 64
Data Sheet
AD9142
1.4
2× INTERPOLATION
4× INTERPOLATION
8× INTERPOLATION
1.2
POWER (W)
1.0
0.8
0.6
0.4
10930-018
0
0
200
400
600
800
1000
1200
1400
1600
1800
fDAC (MHz)
Figure 21. Single-Tone fDAC = 1474.56 MHz,
fOUT = 280 MHz, −14 dBFS
10930-021
0.2
Figure 24. Total Power Consumption vs. fDAC over Interpolation
450
2× INTERPOLATION
4× INTERPOLATION
8× INTERPOLATION
400
350
DVDD18 (mA)
300
250
200
150
100
50
200
400
600
800
1000
1200
1400
1600
1800
10930-024
0
1600
10930-022
10930-019
0
fDAC (MHz)
Figure 22. 4C WCDMA ACLR Performance,
IF = 280 MHz, fDAC = 1474.28 MHz
Figure 25. DVDD18 Current vs. fDAC over Interpolation
0.30
NCO
INV SINC
DIG GAIN, PHASE, AND OFFSET
0.25
DVDD18 (mA)
0.20
0.15
0.10
0.05
10930-020
0
Figure 23. Single-Tone SFDR fDAC = 1474.56 MHz,
4× Interpolation, fOUT = 10 MHz, −14 dBFS
0
200
400
600
800
1000
1200
1400
fDAC (MHz)
Figure 26. DVDD18 Current vs. fDAC over Digital Functions
Rev. 0 | Page 15 of 64
AD9142
250
Data Sheet
CVDD18 PLL OFF
AVDD33
CVDD18 PLL ON
150
100
50
0
0
200
400
600
800
1000
1200
1400
fDAC (MHz)
1600
10930-023
SUPPLY CURRENT (mA)
200
Figure 27. CVDD18, AVDD33 Current vs. fDAC
Rev. 0 | Page 16 of 64
Data Sheet
AD9142
TERMINOLOGY
Integral Nonlinearity (INL)
INL is the maximum deviation of the actual analog output from
the ideal output, determined by a straight line drawn from zero
scale to full scale.
Settling Time
Settling time is the time required for the output to reach and
remain within a specified error band around its final value,
measured from the start of the output transition.
Differential Nonlinearity (DNL)
DNL is the measure of the variation in analog value, normalized
to full scale, associated with a 1 LSB change in digital input code.
Spurious Free Dynamic Range (SFDR)
SFDR is the difference, in decibels, between the peak amplitude
of the output signal and the peak spurious signal within the dc
to Nyquist frequency of the DAC. Typically, the interpoloation
filters reject energy in this band. This specification, therefore,
defines how well the interpolation filters work and the effect of
other parasitic coupling paths on the DAC output.
Offset Error
Offset error is the deviation of the output current from the ideal
of 0 mA. For IOUT1P, 0 mA output is expected when all inputs
are set to 0. For IOUT1N, 0 mA output is expected when all
inputs are set to 1.
Gain Error
Gain error is the difference between the actual and ideal output
span. The actual span is determined by the difference between
the output when all inputs are set to 1 and the output when all
inputs are set to 0.
Output Compliance Range
The output compliance range is the range of allowable voltage
at the output of a current output DAC. Operation beyond the
maximum compliance limits can cause either output stage
saturation or breakdown, resulting in nonlinear performance.
Temperature Drift
Temperature drift is specified as the maximum change from
the ambient (25°C) value to the value at either TMIN or TMAX.
For offset and gain drift, the drift is reported in ppm of fullscale range (FSR) per degree Celsius. For reference drift, the
drift is reported in ppm per degree Celsius.
Power Supply Rejection (PSR)
PSR is the maximum change in the full-scale output as the
supplies are varied from minimum to maximum specified
voltages.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the measured output signal
to the rms sum of all other spectral components below the Nyquist
frequency, excluding the first six harmonics and dc. The value
for SNR is expressed in decibels.
Interpolation Filter
If the digital inputs to the DAC are sampled at a multiple rate of
fDATA (interpolation rate), a digital filter can be constructed that
has a sharp transition band near fDATA/2. Images that typically
appear around fDAC (output data rate) can be greatly suppressed.
Adjacent Channel Leakage Ratio (ACLR)
ACLR is the ratio in decibels relative to the carrier (dBc) between
the measured power within a channel relative to its adjacent
channel.
Complex Image Rejection
In a traditional two-part upconversion, two images are created
around the second IF frequency. These images have the effect
of wasting transmitter power and system bandwidth. By placing
the real part of a second complex modulator in series with the
first complex modulator, either the upper or lower frequency
image near the second IF can be rejected.
Rev. 0 | Page 17 of 64
AD9142
Data Sheet
SERIAL PORT OPERATION
54 CS
SPI
PORT 53 SCLK
52 SDIO
10930-025
The serial port is a flexible, synchronous serial communications
port that allows easy interfacing to many industry standard microcontrollers and microprocessors. The serial I/O is compatible
with most synchronous transfer formats, including both the
Motorola SPI and Intel® SSR protocols. The interface allows
read/write access to all registers that configure the AD9142.
MSB-first or LSB-first transfer formats are supported. The serial
port interface is a 3-wire only interface. The input and output
share a single pin input/output (SDIO).
SERIAL PORT PIN DESCRIPTIONS
Serial Clock (SCLK)
The serial clock pin synchronizes data to and from the device
and runs the internal state machines. The maximum frequency
of SCLK is 40 MHz. All data input is registered on the rising edge
of SCLK. All data is driven out on the falling edge of SCLK.
Chip Select (CS)
Figure 28. Serial Port Interface Pins
There are two phases to a communication cycle with the AD9142.
Phase 1 is the instruction cycle (the writing of an instruction
byte into the device), coincident with the first 16 SCLK rising
edges. The instruction word provides the serial port controller
with information regarding the data transfer cycle, Phase 2, of
the communication cycle. The Phase 1 instruction word defines
whether the upcoming data transfer is a read or write, along with
the starting register address for the following data transfer.
A logic high on the CS pin, followed by a logic low, resets the
serial port timing to the initial state of the instruction cycle.
From this state, the next 16 rising SCLK edges represent the
instruction bits of the current I/O operation.
The remaining SCLK edges are for Phase 2 of the communication
cycle. Phase 2 is the actual data transfer between the device and
the system controller. Phase 2 of the communication cycle is a
transfer of one data byte. Registers change immediately upon
writing to the last bit of each transfer byte, except for the frequency
tuning word and NCO phase offsets, which change only when
the frequency tuning word (FTW) update bit is set.
DATA FORMAT
The instruction byte contains the information shown in Table 10.
Table 10. Serial Port Instruction Word
I15 (MSB)
R/W
A14 to A0 (Bit 14 to Bit 0 of the instruction word) determine
the register that is accessed during the data transfer portion of
the communication cycle. For multibyte transfers, A14 is the
starting address; the device generates the remaining register
addresses based on the SPI_LSB_FIRST bit.
I[14:0]
A[14:0]
R/W (Bit 15 of the instruction word) determines whether a read
or a write data transfer occurs after the instruction word write.
Logic 1 indicates a read operation and Logic 0 indicates a write
operation.
CS is an active low input that starts and gates a communication
cycle. It allows more than one device to be used on the same serial
communications line. The SDIO pins enter a high impedance
state when the CS input is high. During the communication
cycle, CS should stay low.
Serial Data I/O (SDIO)
The SDIO pin is a bidirectional data line.
SERIAL PORT OPTIONS
The serial port can support both MSB-first and LSB-first data
formats. This functionality is controlled by the SPI_LSB_FIRST bit
(Register 0x00, Bit 6). The default is MSB first (LSB_FIRST = 0).
When SPI_LSB_FIRST = 0 (MSB first), the instruction and data
bits must be written from MSB to LSB. Multibyte data transfers
in MSB-first format start with an instruction word that includes the
register address of the most significant data byte. Subsequent data
bytes must follow from high address to low address. In MSB-first
mode, the serial port internal word address generator decrements
for each data byte of the multibyte communication cycle.
When SPI_LSB_FIRST = 1 (LSB first), the instruction and data
bits must be written from LSB to MSB. Multibyte data transfers
in LSB-first format start with an instruction word that includes the
register address of the least significant data byte. Subsequent data
bytes must follow from low address to high address. In LSB-first
mode, the serial port internal word address generator increments
for each data byte of the multibyte communication cycle.
If the MSB-first mode is active, the serial port controller data
address decrements from the data address written toward 0x00
for multibyte I/O operations. If the LSB-first mode is active, the
serial port controller data address increments from the data
address written toward 0xFF for multibyte I/O operations.
Rev. 0 | Page 18 of 64
Data Sheet
AD9142
tDCSB
INSTRUCTION CYCLE
tSCLK
DATA TRANSFER CYCLE
CS
CS
tPWH
SCLK
R/W A14 A13
A3
A2 A1
A0 D7N D6N D5N
D30 D20 D10 D00
tDS
SDIO
Figure 29. Serial Register Interface Timing, MSB First
INSTRUCTION CYCLE
tDH
INSTRUCTION BIT 15
INSTRUCTION BIT 14
10930-028
SCLK
10930-026
SDIO
tPWL
Figure 31. Timing Diagram for Serial Port Register Write
CS
DATA TRANSFER CYCLE
CS
A0
A1
A2
A12 A13 A14 R/W D00 D10 D20
D4N D5N D6N D7N
10930-027
SDIO
tDV
SDIO
DATA BIT n
DATA BIT n – 1
Figure 32. Timing Diagram for Serial Port Register Read
Figure 30. Serial Register Interface Timing, LSB First
Rev. 0 | Page 19 of 64
10930-029
SCLK
SCLK
AD9142
Data Sheet
DATA INTERFACE
LVDS INPUT DATA PORTS
BYTE INTERFACE MODE
The AD9142 has a 16-bit LVDS bus that accepts 16-bit I and Q
data either in word wide (16-bit) or byte wide (8-bit) formats. In
the word wide interface mode, the data is sent over the entire
16-bit data bus. In the byte wide interface mode, the data is sent
over the lower 8-bit (D7 to D0) LVDS bus. Table 11 lists the pin
assignment of the bus and the SPI register configuration for
each mode.
In byte mode, the required sequence of the input data stream is
I[15:8], I[7:0], Q[15:8], Q[7:0]. A frame signal is required to
align the order of input data bytes properly. Time align both the
DCI signal and frame signal with the data. The rising edge of
the frame indicates the start of the sequence. The frame can be
either a one shot or periodical signal as long as its first rising
edge is correctly captured by the device. For a one shot frame,
the frame pulse needs to hold at high for at least one DCI cycle.
For a periodical frame, the frequency needs to be
Table 11. LVDS Data Input Modes
Pin Assignment
D15 to D0
D7 to D0
SPI Register Configuration
Register 0x26, Bit 0 = 0
Register 0x26, Bit 0 = 1
fDCI/(2 × n)
where n is a positive integer, that is, 1, 2, 3, …
Figure 34 is an example of signal timing in byte mode.
WORD INTERFACE MODE
In word mode, the digital clock input (DCI) signal is a reference
bit that generates a double data rate (DDR) data sampling clock.
Time align the DCI signal with the data. The IDAC data follows
the rising edge of the DCI, and the QDAC data follows the
falling edge of the DCI, as shown in Figure 33.
BYTE MODE
INPUT DATA[7:0]
Q0
I1
DCI
Figure 33. Timing Diagram for Word Mode
Q0[15:8]
Q0[7:0]
FRAME
Figure 34. Timing Diagram for Byte Mode
Q1
10930-030
I0
I0[7:0]
DCI
WORD MODE
INPUT DATA[15:0]
I0[15:8]
10930-031
Interface Mode
Word
Byte
DATA INTERFACE CONFIGURATION OPTIONS
To provide more flexibility for the data interface, some
additional options are listed in Table 12.
Table 12. Data Interface Configuration Options
Register 0x26
Data Format (Bit 7)
Data Pairing (Bit 6)
Data Bus Invert (Bit 5)
Rev. 0 | Page 20 of 64
Function
Select between binary and twos
complement formats.
Indicate I/Q data pairing on data input.
This allows the I and Q data that is
received to be paired in various ways.
Swaps the bit order of the data input
port. Remaps the input data from
D[15:0] to D[0:15].
Data Sheet
AD9142
LVDS Input Level Requirements
receiver requires a minimum of ±225 mV swing at its input.
Figure 35 shows the LVDS input configuration and the required
swing levels. Because the DCI is typically generated from the
same bank as the data in the data source, it is recommended
that the output swing of the LVDS driver be larger than the
required DCI input level, thus meeting both input data and DCI
requirements.
There are two types of LVDS receivers in the AD9142. The
16-bit data bus and the frame input share the same LVDS
receiver design. The DCI uses a different LVDS design. The
main difference between the two LVDS receivers is the required
input differential swing level. The data bus and frame receiver
require a minimum of ±100 mV swing at the input. The DCI
AD9142
+
Dn
100Ω
DATA
RECEIVER
TO INTERNAL
DIGITAL
–
DnP
DnN
GND
VCM = (VINP + VINN)/2 = 1.2V
+
DCI
100Ω
DCI
RECEIVER
TO INTERNAL
DIGITAL
–
DCIP
DCIN
AD9142 LVDS INPUT CONFIGURATION
DCIP
1.32V
DCIN
1.1V
1.25V
1.15V
DnP
DnN
+225mV
0V
DCI
+100mV
0V
–100mV
Dn
–225mV
AD9142 DCI INPUT LVDS LEVEL
AD9142 DATA AND
FRAME INPUT LVDS LEVEL
Figure 35. Data Interface Voltage Swing Requirements
Rev. 0 | Page 21 of 64
10930-038
GND
AD9142
Data Sheet
INTERFACE DELAY LINE
Interface Timing Requirements
A four-tap delay line is provided for the user to adjust the
timing between the data bus and the DCI. Table 13 specifies the
setup and hold times for each delay tap.
The following example illustrates how to calculate the optimal
delay at the data source to achieve the best sampling timing in
the delay line-based mode:
There is a fixed 1.9 ns delay on the DCI when the delay line is
enabled. Each tap adds a nominal delay of 300 ps to the fixed
delay. To achieve the best timing margin, that is, to center the
setup and hold window in the middle of the data eye, the user
may need to add a delay on the data bus with respect to the DCI
in the data source. Figure 36 is an example of calculating the
optimal external delay.
•
•
Table 13. Setup and Hold Times
1
0
0x00
0x0
−1.25
2.51
1.26
1
0x07
0x0
−1.50
2.82
1.32
2
0x7F
0x0
−1.70
3.23
1.53
3
0xFF
0x5
−1.93
3.64
1.71
The negative sign indicates the direction of the setup time. The setup time is
defined as positive when it is on the left side of the clock edge and negative
when it is on the right side of the clock edge.
The shadow area in Figure 36 is the interface setup and hold
time window set to 0. To optimize the interface timing, this
window must be placed in the middle of the data transitions.
Because the input is double data rate, the available data period
is 2.5 ns. Therefore, the optimal data bus delay, with respect to
the DCI at the data source, can be calculated as
t DELAY =
(| t S | + | t H |)
2
−
t DATA PERIOD
= 1.88 − 1.25 = 0.63 ns
2
SPI Sequence to Enable Delay Line-Based Mode
It is recommended that the following SPI sequence be used to
enable the delay line-based mode:
1.
2.
0x79 → 0x18 /* Configure Data Interface */
0x5E → 0x00 /* Delay setting 0 */
0x5F → 0x00
0x5F[3] → 1b /* Enable the delay line */
3.
tDELAY = 0.63ns
tDATA PERIOD = 2.5ns
INPUT DATA [15:0]
WITH OPTIMIZED DELAY
DATA EYE
|tS| = 1.25ns
|tH| = 2.51ns
DCI = 200MHz
NO DATA TRANSITION
Figure 36. Example of Interfacing Timing in the Delay Line-Based Mode
Rev. 0 | Page 22 of 64
10930-039
Delay Setting
Register 0x5E[7:0]
Register 0x5F[2:0]
tS (ns)1
tH (ns)
|tS + tH| (ns)
fDCI = 200 MHz
Delay setting = 0
Data Sheet
AD9142
FIFO OPERATION
As is shown in the Data Interface section, the AD9142 adopts
source synchronous clocking in the data receiver. The nature of
source synchronous clocking is the creation of a separate clock
domain at the receiving device. In the DAC, it is the DAC clock
domain, that is, the DACCLK. Therefore, there are two clock
domains inside of the DAC: the DCI and the DACCLK. Often,
these two clock domains are not synchronous, requiring an
additional stage to adjust the timing for proper data transfer. In
the AD9142, a FIFO stage is inserted between the DCI and
DACCLK domains to transfer the received data into the core
clock domain (DACCLK) of the DAC.
is read from the FIFO register, which is determined by the read
pointer, and fed into the digital datapath. The value of the read
pointer is incremented every time data is read into the datapath
from the FIFO. The FIFO pointers are incremented at the data
rate, which is the DACCLK rate divided by the interpolation rate.
The AD9142 contains a 2-channel, 16-bit wide, 8-word deep
FIFO. The FIFO acts as a buffer that absorbs timing variations
between the two clock domains. The timing budget between the
two clock domains in the system is significantly relaxed due to
the depth of the FIFO.
Normally, data is written to and read from the FIFO at the same
rate to maintain a constant FIFO depth. If data is written to the
FIFO faster than data is read, the FIFO depth increases. If data
is read from the FIFO faster than data is written to it, the FIFO
depth decreases. For optimal timing margin, maintain the FIFO
depth near half full (a difference of four between the write
pointer and read pointer values). The FIFO depth represents the
FIFO pipeline delay and is part of the overall latency of the
AD9142.
Figure 37 shows the block diagram of the datapath through the
FIFO. The input data is latched into the device, formatted, and
then written into the FIFO register, which is determined by the
FIFO write pointer. The value of the write pointer is incremented
every time a new word is loaded into the FIFO. Meanwhile, data
Valid data is transmitted through the FIFO as long as the FIFO
does not overflow (full) or underflow (empty). An overflow or
underflow condition occurs when the write pointer and read
pointer point to the same FIFO slot. This simultaneous access of
data leads to unreliable data transfer through the FIFO and must be
avoided.
FIFO WRITE CLOCK
FIFO READ CLOCK
DACCLK
÷INT
FIFO
FIFO SLOT 0
FIFO SLOT 2
DATA
RECEIVER
INPUT DATA [15:0]
FIFO SLOT 3
DATA
FORMAT
LATCHED
DATA [15:0]
I[15:0]
I DATA PATH
FIFO SLOT 1
RETIMED DCI
DCI
I[15:0]
I DAC
READ
POINTER
FIFO SLOT 4
I/Q[31:0]
WRITE
POINTER
FIFO SLOT 5
FIFO SLOT 6
Q[15:0]
Q[15:0]
Q DATA PATH
Q DAC
FIFO SLOT 7
FRAME
RESET
LOGIC
FIFO LEVEL
FIFO LEVEL REQUEST
REG 0x23
Figure 37. Block Diagram of FIFO
Rev. 0 | Page 23 of 64
10930-040
SPI FIFO RESET
REG 0x25[0]
AD9142
Data Sheet
RESETTING THE FIFO
SERIAL PORT INITIATED FIFO RESET
Upon power-on of the device, the read and write pointers start
to roll around the FIFO from an arbitrary slot; consequently, the
FIFO depth is unknown. To avoid a concurrent read and write
to the same FIFO address and to assure a fixed pipeline delay
from power-on to power-on, it is important to reset the FIFO
pointers to a known state each time the device powers on or
wakes up. This state is specified in the requested FIFO level
(FIFO depth and FIFO level are used interchangeably in this
document), which consists of two parts: the integral FIFO level
and the fractional FIFO level.
A SPI initiated FIFO reset is the most common method to reset
the FIFO. To initialize the FIFO level through the serial port,
toggle FIFO_SPI_RESET_REQUEST (Register 0x25[0]) from
0 to 1 and back to 0. When the write to this register is complete,
the FIFO level is initialized to the requested FIFO level and the
readback of FIFO_SPI_RESET_ACK (Register 0x25[1]) is set
to 1. The FIFO level readback, in the same format as the FIFO
level request, should be within ±1 DACCLK cycle of the
requested level. For example, if the requested value is 0x40 in
4× interpolation, the readback value should be one of the
following: 0x33, 0x40, or 0x41. The range of ±1 DACCLK cycle
indicates the default DAC latency uncertainty from power-on
to power-on without turning on synchronization.
The integer FIFO level represents the difference of the states
between the read and write point in the unit of input data period
(1/fDATA). The fractional FIFO level represents the difference of
the FIFO pointers smaller than the input data period. The
resolution of the fractional FIFO level is the input data period
divided by the interpolation ratio and, thus, it is equal to one
DACCLK cycle.
The exact FIFO level, that is, the FIFO latency, can be calculated
by
FIFO Latency = Integral Level + Fractional Level
Because the FIFO has eight data slots, there are eight possible
FIFO integral levels. The maximum supported interpolation
rate in the AD9142 is 8× interpolation. Therefore, there are eight
possible FIFO fractional levels. Two 3-bit registers in Register
0x23 are assigned to represent each level separately; Bits[6:4]
represent the FIFO integral level and Bits[2:0] represent the FIFO
fractional level. For example, if the interpolation rate is 4× and
the desired total FIFO depth is 4.5 input data periods, set the
FIFO_LEVEL_CONFIG (Register 0x23) to 0x42 (4 here means
four data cycles and 2 means two DAC cycles, which is half of a
data cycle). Note that there are only four possible fractional
levels in the case of 4× interpolation. Table 14 shows additional
examples of configuring the desired FIFO level in various
interpolation rate modes.
Table 14. Examples of FIFO Level Configuration
Interpolation
Rate
2×
4×
8×
Example
FIFO Level
(1/fDATA)
3 + 1/2
4 + 1/4
4 + 3/8
Integer Level
(Register 0x23[6:4])
3
4
4
Fractional Level
(Register 0x23[2:0])
1
1
3
By default, the FIFO level is 4.0. It can be programmed to any
allowed value from 0.0 to 7.x. The maximum allowed number
for x is the interpolation rate minus 1. For example, in 8×
interpolation, the maximum allowed for x is 7.
The following two ways are used to reset the FIFO and initialize
the FIFO level:
•
•
Serial port (SPI) initiated FIFO reset.
Frame initiated FIFO reset.
The recommended procedure for a serial port FIFO reset is as
follows:
1.
2.
3.
4.
5.
6.
7.
8.
Configure the DAC in the desired interpolation mode
(Register 0x28[1:0]).
Ensure that the DACCLK and DCI are running and stable
at the clock inputs.
Program Register 0x23 to the customized value, if the
desired value is not 0x40.
Request the FIFO level reset by setting Register 0x25[0] to 1.
Verify that the part acknowledges the request by setting
Register 0x25[1] to 1.
Remove the request by setting Register 0x25[0] to 0.
Verify that the part drops the acknowledge signal by setting
Register 0x25[1] to 0.
Read back Register 0x24 multiple times to verify that the
actual FIFO level is set to the requested level and that the
readback values are stable. By design, the readback should
be within ±1 DACCLK around the requested level.
FRAME INITIATED FIFO RESET
The frame input has two functions. One function is to indicate
the beginning of a byte stream in the byte interface mode, as
discussed in the Data Interface section. The other function is
to initialize the FIFO level by asserting the frame signal high
for at least the time interval required to load complete data to
the I and QDACs. This corresponds to one DCI period in word
mode and two DCI periods in byte mode. Note that this
requirement of the frame pulse length is longer than that of the
frame signal when it serves only to assemble the byte stream.
The device accepts either a continuous frame or a one shot
frame signal.
In the continuous reset mode, the FIFO responds to every valid
frame pulse and resets itself. In the one shot reset mode, the
FIFO responds only to the first valid frame pulse after the
FRAME_RESET_MODE bits (Register 0x22[1:0]) are set.
Therefore, even with a continuous frame input, the FIFO resets
one time only; this prevents the FIFO from toggling between
the two states from periodic resets. The one shot frame reset
mode is the default and the recommended mode.
Rev. 0 | Page 24 of 64
Data Sheet
AD9142
The recommended procedure for a frame initiated FIFO reset is
as follows:
1.
2.
3.
4.
5.
6.
7.
8.
Configure the DAC in the desired interpolation mode
(Register 0x28[1:0]).
Ensure that the DACCLK and DCI are running and stable at
the clock inputs.
Program Register 0x23 to the customized value, if the
desired value is not 0x40.
Configure the FRAME_RESET_MODE bits (Register
0x22[1:0])to 00b.
Choose whether continuous or one shot mode is desired by
writing 0 or 1 to EN_CON_FRAME_RESET (Register
0x22[2]).
Toggle the frame input from 0 to 1 and back to 0. The pulse
width needs to be longer than the minimum requirement.
a. If the frame input is a continuous clock, turn on the
signal.
Read back FRAME_RESET_ACK, Register 0x22[3], to
verify that the reset is complete.
Read back Register 0x24 multiple times to verify that the
actual FIFO level is set to the requested level and the
readback values are stable. By design, the readback should be
within ±1 DACCLK around the requested level.
Monitoring the FIFO Status
The real-time FIFO status can be monitored from the SPI
Register 0x24 and reflects the real-time FIFO depth after a FIFO
reset. Without timing drifts in the system, this readback should
not change from that which resulted from the FIFO reset. When
there is a timing drift or other abnormal clocking situation, the
FIFO level readback can change. However, as long as the FIFO
does not overflow or underflow, there is no error in data transmission. Three status bits in Register 0x06, Bits[2:0], indicate if
there are FIFO underflows, overflows, or similar situations. The
status of the three bits can be latched and used to trigger
hardware interrupts, IRQ1 and IRQ2. To enable latching and
interrupts, configure the corresponding bits in Register 0x03
and Register 0x04.
Rev. 0 | Page 25 of 64
AD9142
Data Sheet
DIGITAL DATAPATH
HB1
HB3
HB2
COARSE AND
FINE
MODULATION
DIGITAL GAIN
AND PHASE
AND OFFSET
ADJUSTMENT
INV
SINC
10930-041
INPUT
POWER
DETECTION
AND
PROTECTION
Figure 38. Block Diagram of Digital Datapath
The block diagram in Figure 38 shows the functionality of the
digital datapath. The digital processing includes
The interpolation filters accept I and Q data streams and
process them as two independent data streams, whereas the
quadrature modulator and phase adjustment block accepts I
and Q data streams as a quadrature data stream. Therefore,
quadrature input data is required when digital modulation and
phase adjustment functions are used.
–0.02
–0.04
–0.06
–0.10
0
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
FREQUENCY (Hz)
10930-042
–0.08
Figure 39. Pass-Band Detail of 2× Mode
10
INTERPOLATION FILTERS
The AD9142 provides three interpolation modes (see Table 6).
Each mode offers a different usable signal bandwidth in an
operating mode. Which mode to select depends on the required
signal bandwidth and the DAC update rate. Refer to Table 6 for
the maximum speed and signal bandwidth of each interpolation
mode.
0
–10
–20
MAGNITUDE (dB)
The transmit path contains three interpolation filters. Each of
the three interpolation filters provides a 2× increase in output data
rate and a low-pass function. The half-band (HB) filters are cascaded to provide 4× or 8× interpolation ratios.
The usable bandwidth is defined as the frequency band over
which the filters have a pass-band ripple of less than ±0.001 dB
and a stop band rejection of greater than 85 dB.
2× Interpolation Mode
Figure 39 and Figure 40 show the pass-band and all-band filter
response for 2× mode. Note that the transition from the
transition band to the stop band is much sharper than the transition from the pass band to the transition band. Therefore, when
the desired output signal moves out of the defined pass band,
the signal image, which is supposed to be suppressed by the stop
band, grows faster than the droop of the signal itself due to the
degraded pass-band flatness. In cases where the degraded image
rejection is acceptable or can be compensated by the analog
low-pass filter at the DAC output, it is possible to let the output
signal extend beyond the specified usable signal bandwidth.
Rev. 0 | Page 26 of 64
–30
–40
–50
–60
–70
–80
–90
–100
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
FREQUENCY (Hz)
Figure 40. All-Band Response of 2× Mode
1.8
2.0
10930-043
•
•
0
An input power detection block
Three half-band interpolation filters
A quadrature modulator consisting of a fine resolution
NCO and an fS/4 coarse modulation block
An inverse sinc filter
A gain and phase and offset adjustment block
MAGNITUDE (dB)
•
•
•
0.02
Data Sheet
AD9142
4× Interpolation Mode
10
0
Figure 41 and Figure 42 show the pass-band and all-band filter
responses for 4× mode.
–10
–20
MAGNITUDE (dB)
0.02
–0.02
–30
–40
–50
–60
–70
–0.04
–80
–90
–0.06
–100
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
FREQUENCY (Hz)
–0.08
1.8
2.0
10930-049
MAGNITUDE (dB)
0
0
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
FREQUENCY (Hz)
10930-046
Figure 44. All-Band Response of 8× Mode
–0.10
Figure 41. Pass-Band Detail of 4× Mode
10
0
–10
MAGNITUDE (dB)
–20
–30
–40
–50
–60
–70
–80
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
FREQUENCY (Hz)
10930-047
–90
–100
Figure 42. All-Band Response of 4× Mode
8× Interpolation Mode
Figure 43 and Figure 44 show the pass-band and all-band filter
responses for 8× mode. The maximum DAC update rate is 1.6 GHz,
and the maximum input data rate that is supported in this mode is
200 MHz (1.6 GHz/8).
0.02
–0.02
–0.04
Lower Coefficient
H(1)
H(2)
H(3)
H(4)
H(5)
H(6)
H(7)
H(8)
H(9)
H(10)
H(11)
H(12)
H(13)
H(14)
H(15)
H(16)
H(17)
H(18)
H(19)
H(20)
H(21)
H(22)
H(23)
H(24)
H(25)
H(26)
H(27)
H(28)
–0.06
–0.08
–0.10
0
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
FREQUENCY (Hz)
0.45
10930-048
MAGNITUDE (dB)
0
Table 15. Half-Band Filter 1 Coefficient
Figure 43. Pass-Band Detail of 8× Mode
Rev. 0 | Page 27 of 64
Upper Coefficient
H(55)
H(54)
H(53)
H(52)
H(51)
H(50)
H(49)
H(48)
H(47)
H(46)
H(45)
H(44)
H(43)
H(42)
H(41)
H(40)
H(39)
H(38)
H(37)
H(36)
H(35)
H(34)
H(33)
H(32)
H(31)
H(30)
H(29)
Integer Value
−4
0
+13
0
−32
0
+69
0
−134
0
+239
0
−401
0
+642
0
−994
0
+1512
0
−2307
0
+3665
0
−6638
0
+20,754
+32,768
AD9142
Data Sheet
Upper Coefficient
H(23)
H(22)
H(21)
H(20)
H(19)
H(18)
H(17)
H(16)
H(15)
H(14)
H(13)
Integer Value
−2
0
+17
0
−75
0
+238
0
−660
0
+2530
+4096
Table 17. Half-Band Filter 3 Coefficient
Lower Coefficient
H(1)
H(2)
H(3)
H(4)
H(5)
H(6)
Upper Coefficient
H(11)
H(10)
H(9)
H(8)
H(7)
Integer Value
+29
0
−214
0
+1209
+2048
FTW[31:0]
~
NCO
PHASE[15:0]
SINE
Q DATA IN
The NCO modulator mixes the carrier signal generated by the
NCO with the I and Q signals. The NCO produces a quadrature
carrier signal to translate the input signal to a new center frequency. A complex carrier signal is a pair of sinusoidal waveforms
of the same frequency, offset 90 degrees from each other. The
frequency of the complex carrier signal is set via NCO_FREQ_
TUNING_WORD[31:0] in Register 0x31 through Register 0x34.
The NCO operating frequency, fNCO, is always equal to fDAC, the
DACCLK frequency. The frequency of the complex carrier
signal can be set from dc up to ±0.5 × fNCO.
The frequency tuning word (FTW) is in twos complement
format. It can be calculated as
f DAC
f
≤ f CARRIER ≤ DAC
2
2
−
The AD9142 provides two modes to modulate the baseband
quadrature signal to the desired DAC output frequency.
FTW =
Coarse (fS/4) modulation
Fine (NCO) modulation
f CARRIER
f DAC
FTW = (1 −
fS/4 Modulation
The fS/4 modulation is a convenient and low power modulation
mode to translate the input baseband frequency to a fixed fS/4
IF frequency, fS being the DAC sampling rate. When modulation
frequencies other than this frequency are required, the NCO
modulation mode must be used.
NCO Modulation
The NCO modulation mode makes use of a numerically
controlled oscillator (NCO), a phase shifter, and a complex
modulator to provide a means for modulating the signal by a
programmable carrier signal. A block diagram of the digital
modulator is shown in Figure 45. The NCO modulation allows
the DAC output signal to be placed anywhere in the output
spectrum with very fine frequency resolution.
Q DATA OUT
Figure 45. NCO Modulator Block Diagram
DIGITAL MODULATION
•
•
COSINE
10930-050
Lower Coefficient
H(1)
H(2)
H(3)
H(4)
H(5)
H(6)
H(7)
H(8)
H(9)
H(10)
H(11)
H(12)
I DATA OUT
I DATA IN
Table 16. Half-Band Filter 2 Coefficient
( )( f
× 232
f CARRIER
f DAC
CARRIER
≥ 0)
) × (232 ) ( f CARRIER < 0 )
The generated quadrature carrier signal is mixed with the I and
Q data. The quadrature products are then summed into the I
and Q data paths, as shown in Figure 45.
Updating the Frequency Tuning Word
The frequency tuning word registers are not updated immediately
upon writing, as are other configuration registers. Similar to
FIFO reset, the NCO update can be triggered in two ways.
•
•
Rev. 0 | Page 28 of 64
SPI initiated update
Frame initiated update
Data Sheet
AD9142
SPI Initiated Update
quadrature gain and phase adjust values optimizes image
rejection in single sideband radios.
In the SPI initiated update method, the user simply toggles
Register 0x30[0] (NCO_SPI_UPDATE_REQ) after configuring
the NCO settings. The NCO is updated on the rising edge (from
0 to 1) in this bit. Register 0x30[1] (NCO_SPI_UPDATE_ACK)
goes high when the NCO is updated. A falling edge (from 1 to
0) in Register 0x30[0] clears Bit 1 of Register 0x30 and prepares
the NCO for the next update operation. This update method is
recommended when there is no requirement to align the DAC
output from multiple devices because SPI writes to multiple
devices are asynchronous.
Ordinarily, the I and Q channels have the same gain or signal
magnitude. The quadrature gain adjustment is used to balance the
gain between the I and Q channels. The digital gain of the I and Q
channels can be adjusted independently through two 6-bit registers,
IDAC_GAIN_ADJ (Register 0x3F[5:0]) and QDAC_GAIN_ADJ
(Register 0x40[5:0]). The range of the adjustment is [0, 2] or [−∞,
6 dB] with a step size of 2−5 (−30 dB). The default setting is 0x20,
corresponding to a gain equal to 1 or 0 dB.
Frame Initiated Update
Quadrature Phase Adjustment
When the DAC output from multiple devices needs to be well
aligned with NCO turned on, the frame initiated update is
recommended. In this method, the NCOs from multiple devices
are updated at the same time upon the rising edge of the frame
signal. To use this update method, the FRAME_RESET_MODE
(Register 0x22[1:0]) needs to be set in NCO only or FIFO and
NCO, depending on whether FIFO reset is needed at the same
time. The second step is to ensure that the reset mode is in one
shot mode (EN_CON_FRAME_RESET, Register 0x22[2] = 0).
When this second step is completed, the NCO waits for a valid
frame pulse and updates the FTW accordingly. The user can verify
if the frame pulse is correctly received by reading Register 0x30[6]
(NCO_FRAME_ UPDATE_ACK) wherein a 1 indicates a
complete update operation. See the FIFO Operation section for
information to generate a valid frame pulse.
Under normal circumstances, I and Q channels have an angle of
precisely 90 degrees between them. The quadrature phase adjustment is used to change the angle between the I and Q channels.
IQ_PHASE_ADJ[12:0] (Register 0x37 and Register 0x38) provide
an adjustment range of ±14 degrees with a resolution of 0.0035
degrees. If the original angle is precisely 90 degrees, setting
IQ_PHASE_ADJ[12:0] to 0x0FFF adds approximately 14 degrees
between I and QDAC outputs, creating an angle of 104 degrees
between the channels. Likewise, if the original angle is precisely
90 degrees, setting IQ_PHASE_ADJ[12:0] to 0x1000 adds
approximately −14 degrees between the I and QDAC outputs,
creating an angle of 76 degrees between the channels.
The application requirements of the input data rate
The interpolation ratio
The output signal center frequency
The output signal bandwidth
Given these four parameters, the first step in configuring the
datapath is to verify that the device supports the desired input
data rate, the DAC sampling rate, and the bandwidth requirements.
After this verification, the modes of the interpolation filters can be
chosen. If the output signal center frequency is different from the
baseband input center frequency, additional frequency offset
requirements are determined and applied with on-chip digital
modulation.
DIGITAL QUADRATURE GAIN AND PHASE
ADJUSTMENT
The digital quadrature gain and phase adjustment function
enables compensation of the gain and phase imbalance of the I
and Q paths caused by analog mismatches between DAC I/Q
outputs, quadrature modulator I/Q baseband inputs, and
DAC/modulator interface I/Q paths. The undesired imbalances
cause unwanted sideband signal to appear at the quadrature
modulator output with significant energy. Tuning the
As shown in Figure 46, the DAC offset current varies as a function
of the I/QDAC_DC_OFFSET values. Figure 46 shows the
nominal current of the positive node of the DAC output, IOUTP,
when the digital inputs are fixed at midscale (0x0000, twos
complement data format) and the DAC offset value is swept from
0x0000 to 0xFFFF. Because IOUTP and IOUTN are complementary
current outputs, the sum of IOUTP and IOUTN is always 20 mA.
Rev. 0 | Page 29 of 64
20
0
15
5
10
10
5
15
0
0x0000
0x4000
0x8000
0xC000
20
0xFFFF
DAC OFFSET VALUE
Figure 46. DAC Output Currents vs. DAC Offset Value
IOUTxN (mA)
•
•
•
•
The dc value of the I datapath and the Q datapath can be controlled
independently by adjusting the values in the two 16-bit registers,
IDAC_DC_OFFSET, Bits[15:0] and QDAC_DC_OFFSET,
Bits[15:0] (Register 0x3B through Register 0x3E). These values
are added directly to the datapath values. Care should be taken
not to overrange the transmitted values.
10930-051
Configuring the AD9142 datapath starts with the following four
parameters:
DC OFFSET ADJUSTMENT
IOUTxP (mA)
DATAPATH CONFIGURATION
Quadrature Gain Adjustment
AD9142
Data Sheet
INVERSE SINC FILTER
INPUT SIGNAL POWER DETECTION AND
PROTECTION
The AD9142 provides a digital inverse sinc filter to compensate
for the DAC rolloff over frequency. The inverse sinc (sinc−1) filter
is a seven tap FIR filter. Figure 47 shows the frequency response
of sin(x)/x rolloff, the inverse sinc filter, and their composite
response. The composite response has less than ±0.05 dB passband ripple up to a frequency of 0.4 × fDAC.
The input signal power detection and protection function detects
the average power of the DAC input signal and prevents overrange
signals from being passed to the next stage. An overrange DAC
output signal can cause destructive breakdown on power sensitive
devices, such as power amplifiers. The power detection and
protection feature of the AD9142 detects overrange signals in
the DAC. When an overrange signal is detected, the protection
function either attenuates or mutes the signal to protect the
downstream devices from abnormal power surges in the signal.
To provide the necessary peaking at the upper end of the pass
band, the inverse sinc filter has an intrinsic insertion loss of about
3.8 dB. The loss of the digital gain can be offset by increasing the
quadrature gain adjustment setting on both the I and Q data paths
to minimize the impact on the output signal-to-noise ratio. However, care is needed to ensure that the additional digital gain does
not cause signal saturation, especially at high output frequencies.
The sinc−1 filter is disabled by default; it can be enabled by setting
the INVSINC_ENABLE bit to 1 in Register 0x27[7]).
Figure 48 shows the block diagram of the power detection and
protection function. The protection block is at the very last
stage of the data path and the detection block uses a separate
path from the data path. The design of the detection block
guarantees that the worst-case latency of power detecting is
shorter than that of the data path. This ensures that the
protection circuit initiates before the overrange signal reaches
the analog DAC core. The sum of I2 and Q2 is calculated as a
representation of the input signal power. Only the upper six
MSBs, D[15:10], of data samples are used in the calculation;
consequently, samples whose power is 36 dB below the fullscale peak power are not detected. The calculated sample power
numbers accumulate through a moving average filter. Its output
is the average of the input signal power in a certain number of
data clock cycles. The length of the filter is configurable through
the SAMPLE_WINDOW_LENGTH (Register 0x2B[3:0]). To
determine whether the input average power is over range, the
device averages the power of the samples in the filter and
compares the average power with a user defined threshold,
OVER_THRESHOLD_LEVEL[11:0] (Register 0x29 and
Register 0x2A). When the output of the averaging filter is larger
than the threshold, the DAC output is either attenuated or muted.
1
–1
–2
–3
–5
0
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
FREQUENCY (Hz)
0.45
0.50
10930-052
–4
Figure 47. Responses of sin(x)/x Roll Off (Blue), the Sinc−1 Filter (Red), and the
Composite of Both (Black)
Table 18. Inverse Sinc Filter
Lower Coefficient
H(1)
H(2)
H(3)
H(4)
Upper Coefficient
H(7)
H(6)
H(5)
The appropriate filter length and average power threshold for
effective protection are application dependent. It is recommended
that experiments be performed with real-world vectors to
determine the values of these parameters.
Integer Value
−1
+4
−16
+192
POWER
PROTECTION
(ATTENUATE
OR MUTE)
SIGNAL
PROCESSING
ENGINE
FIFO
DAC
CORE
POWER DETECTION
I2 + Q2
AVERAGING
FILTER
FILTER LENGTH
SETTINGS
REG 0x2B[3:0]
AVE POWER
REG 0x2C AND
0x2D[4:0]
USER-DEFINED THRESHOLD
REG 0x29 AND 0x2A[4:0]
Figure 48. Block Diagram of Input Signal Power Detection and Protection Function
Rev. 0 | Page 30 of 64
10930-053
MAGNITUDE (dB)
0
Data Sheet
AD9142
TRANSMIT ENABLE FUNCTION
DIGITAL FUNCTION CONFIGURATION
The transmit enable (TXEN) function provides the user a
hardware switch of the DAC output. The function accepts a
CMOS signal via Pin 6 (TXEN). When this signal is detected
high, the transmit path is enabled and the DAC transmits the
data normally. When this signal is detected low, one of the three
actions related to the DAC output is triggered.
Each of the digital gain and phase adjust functions and the
inverse sinc filter can be enabled and adjusted independently.
The pipeline latencies these blocks add into the data path are
different between enabled and disabled. If fixed DAC pipeline
latency is desired during operation, leave these functions always
on or always off after initial configuration.
1.
The digital dc adjust function is always on. The default value is
0; that is, there is no additional dc offset. The pipeline latency that
this block adds is a constant, no matter the value of the dc
offset.
2.
3.
The DAC output is gradually attenuated from full scale gain
to 0. The attenuation step size is set in Register 0x42[5:0].
The DAC is put in sleep mode and the output current is
turned off. Other parts of the DAC are still running in this
mode.
The DAC is put in power-down mode. In this mode, not
only the DAC output current is turned off but the rest of
the DAC is powered down. This minimizes the power
consumption of the DAC when the data is not transmitting
but it takes a bit longer than the first two modes to start to
re-transmit data due to the device power-up time.
There is also a latency difference between using and not using
the input signal power detection and protection function.
Therefore, to keep the overall latency fixed, leave this function
always on or always off after the initial configuration.
The TXEN function also provides a gain ramp-up function that
lets the user turn on the DAC output gradually when the TXEN
signal switches from low to high. The ramp-up gain step can be
configured using Register 0x41[5:0]. Although all of these actions
can be taken through SPI writes, TXEN provides a much faster
way to turn on and off the DAC output. The response time of a SPI
write command is dominated by the SPI port communication
time. This feature is useful when the user must turn off the
DAC very quickly.
Rev. 0 | Page 31 of 64
AD9142
Data Sheet
MULTIDEVICE SYNCHRONIZATION AND FIXED LATENCY
A DAC introduces a variation of pipeline latency to a system.
The latency variation causes the phase of a DAC output to vary
from power-on to power-on. Therefore, the output from
different DAC devices may not be perfectly aligned even with
well aligned clocks and digital inputs. The skew between
multiple DAC outputs varies from power-on to power-on.
In applications such as transmit diversity or digital predistortion, where deterministic latency is desired, the variation
of the pipeline latency must be minimized. Deterministic
latency in this document is defined as a fixed time delay from
the digital input to the analog output in a DAC from power-on
to power-on. Multiple DAC devices are considered synchronized
to each other when each DAC in this group has the same
constant latency from power-on to power-on. Three conditions
must be identical in all of the ready-to-sync devices before these
devices are considered synchronized:
•
•
•
The phase of DAC internal clocks
The FIFO level
The alignment of the input data
VERY SMALL INHERENT LATENCY VARIATION
The innovative architecture of the AD9142 minimizes the
inherent latency variation. The worst-case variation in the
AD9142 is two DAC clock cycles. For example, in the case of a
1.5 GHz sample rate, the variation is less than 1.4 ns under any
scenario. Therefore, without turning on the synchronization
engine, the DAC outputs from multiple AD9142 devices are
guaranteed to be aligned within two DAC clock cycles, regardless
of the timing between the DCI and the DACCLK. No additional
clocks are required to achieve this accuracy. The user must reset
the FIFO in each DAC device through the SPI at start-up.
Therefore, the AD9142 can decrease the complexity of system
design in multi transmit channel applications.
Note the alignment of the DCI signals in the design. The DCI is
used as a reference in the AD9142 design to align the FIFO and
the phase of internal clocks in multiple parts. The achieved
DAC output alignment depends on how well the DCIs are
aligned at the input of each device. The equation below is the
expression of the worst-case DAC output alignment accuracy in
the case of DCI mismatches.
FURTHER REDUCING THE LATENCY VARIATION
For applications that require finer synchronization accuracy
(DAC latency variation < 2 DAC clock cycles), the AD9142 has
a provision for enabling multiple devices to be synchronized to
each other within a single DAC clock cycle.
To further reduce the latency variation in the DAC, the
synchronization machine needs to be turned on and two
external clocks (frame and sync) need to be generated in the
system and fed to all the DAC devices.
Set Up and Hold Timing Requirement
The sync clock (fSYNC) serves as a reference clock in the system
to reset the clock generation circuitry in multiple AD9142 devices
simultaneously. Inside the DAC, the sync clock is sampled by the
DACCLK to generate a reference point for aligning the internal
clocks, so there is a setup and hold timing requirement between
the sync clock and the DAC clock.
If the user adopts the continuous frame reset mode, that is, the
FIFO and sync engine periodically reset, the timing requirements
between the sync clock and the DAC clock must be met.
Otherwise, the device can lose lock and corrupt the output. In
the one shot frame reset mode, it is still recommended that this
timing be met at the time when the sync routine is run because
not meeting the timing can degrade the sync alignment
accuracy by one DAC cycle, as shown in Table 19.
For users who want to synchronize the device in a one-shot
manner and continue to monitor the synchronization status,
the AD9142 provides a sync monitoring mode. It provides a
continuous sync and frame clock to synchronize the part once
and ignore the clock cycles after the first valid frame pulse is
detected. In this way, the user can monitor the sync status
without periodically resynchronizing the device; to engage the
sync monitoring mode, set Register 0x22[1:0] (FRAME_RESET_
MODE) to 11b.
Table 19. Sync Clock and DAC Clock Setup and Hold Times
Falling Edge Sync Timing (default)
tS (ns)
tH (ns)
|tS + tH| (ns)
tSK (OUT) = tSK (DCI) + 2/fDAC
where:
tSK (OUT) is the worst case skew between the DAC output from
two AD9142 devices.
tSK (DCI) is the skew between two DCIs at the DCI input of the
two AD9142 devices.
fDAC is the DACCLK frequency.
The better the alignment of the DCIs, the smaller is the overall
skew between two DAC outputs.
Rev. 0 | Page 32 of 64
Max
246
−11
235
Unit
ps
ps
ps
Data Sheet
AD9142
SYNCHRONIZATION IMPLEMENTATION
Synchronization Procedure for PLL Off
The AD9142 lets the user choose either the rising or falling
edge of the DAC clock to sample the sync clock, which makes it
easier to meet the timing requirements. The sync clock, fSYNC,
should be 1/8 × fDATA or slower by a factor of 2n, n being an
integer (1, 2, 3…). Note that there is a limit on how slow the
sync clock can be because of the ac coupling nature of the sync
clock receiver. Choose an appropriate value of the ac coupling
capacitors to ensure that the signal swing meets the data sheet
specification, as listed in Table 2.
1.
The frame clock resets the FIFO in multiple AD9142 devices.
The frame can be either a one shot or continuous clock. In either
case, the pulse width of the frame must be longer than one DCI
cycle in the word mode and two DCI cycles in the byte mode.
When the frame is a continuous clock, fFRAME should be at 1/8 ×
fDATA or slower by a factor of 2n, n being an integer (1, 2, 3…).
Table 20 lists the requirements of the frame clock in various
conditions.
Table 20. Frame Clock Speed and Pulse Width Requirement
Sync Clock
One Shot
Continuous
1
Maximum
Speed
N/A1
fDATA/8
Minimum Pulse Width
For both one shot and continuous
sync clocks, word mode = one DCI
cycle and byte mode = two DCI cycles.
N/A means not applicable.
2.
3.
4.
5.
6.
7.
8.
Synchronization Procedure for PLL On
Note that, because the sync clock and PLL reference clock share
the same clock and the maximum sync clock rate is fDATA/8, the
same limit also applies to the reference clock. Therefore, only
2× interpolation is supported for synchronization with PLL on.
1.
SYNCHRONIZATION PROCEDURES
When the sync accuracy of an application is looser than two
DAC clock cycles, it is recommended to turn off the synchronization machine because there are no additional steps required,
other than the regular start-up procedure sequence.
For applications that require finer than two-DAC clock cycle
sync accuracy, it is recommended that the procedure in the
Synchronization Procedure for PLL Off or Synchronization
Procedure for PLL On sections be followed to set up the system
and configure the device. For more information about the
details of the synchronization scheme in the AD9142 and using
the synchronization function to correct system skews and drifts,
see the DAC Latency and System Skews section.
Configure the DAC interpolation mode and, if NCO is
used, configure the NCO FTW.
Set up the DAC data interface according to the procedure
outlined in the Data Interface section and verify that the
DLL is locked.
Choose the appropriate mode in FRAME_RESET_MODE.
a. If NCO is not used, choose FIFO only mode.
b. If NCO is used, it must be synchronized. FIFO and
NCO mode can then be used.
Configure Bit 2 in Register 0x22 for continuous or one shot
reset mode. One shot reset mode is recommended.
Ensure that the DACCLK, DCI, and sync clock to all of the
AD9142 devices are running and stable.
Enable the sync engine by writing 1 to Register 0x21[0].
Send a valid frame pulse(s) to all of the AD9142 devices.
Verify that the frame pulse is received by each device by
reading back Register 0x22[3]. All the readback values are 1.
At this point, the devices should be synchronized.
2.
3.
4.
5.
6.
7.
8.
9.
Rev. 0 | Page 33 of 64
Set up the PLL according to the procedure in the Clock
Multiplication section and ensure that the PLL is locked.
Configure the DAC interpolation mode and, if NCO is
used, configure the NCO FTW.
Set up the DAC data interface according to the procedure
in the Data Interface section and verify that the DLL is
locked.
Choose the appropriate mode in FRAME_RESET_MODE.
a. If NCO is not used, choose the FIFO only mode.
b. If NCO is used, it must be synchronized. FIFO and
NCO mode can then be used.
Configure Bit 2 in Register 0x22 for continuous or one shot
reset mode. One shot reset mode is recommended.
Ensure that DACCLK, DCI, and sync clock to all of the
AD9142 devices are running.
Enable the sync engine by writing 1 to Register 0x21[0].
Send a valid frame pulse(s) to all of the AD9142 devices.
Verify that the frame pulse is received by each device by
reading back Register 0x22[3]. All the readback values are 1.
At this point, the devices should be synchronized.
AD9142
Data Sheet
INTERRUPT REQUEST OPERATION
method is by writing 1 to the corresponding event flag bit. The
second method is to use a hardware or software reset to clear the
INTERRUPT_SOURCE signal.
The AD9142 provides an interrupt request output signal on
Pin 50 and Pin 51 (IRQ2 and IRQ1, respectively) that can be used
to notify an external host processor of significant device events.
Upon assertion of the interrupt, query the device to determine
the precise event that occurred. The IRQ1 pin is an open-drain,
active low output. Pull the IRQ1 pin high external to the device.
This pin can be tied to the interrupt pins of other devices with
open-drain outputs to wire-OR these pins together.
The IRQ2 circuitry works in the same way as the IRQ1 circuitry.
Any one or multiple event flags can be enabled to trigger
the IRQ1 and IRQ2 pins. The user can select one or both
hardware interrupt pins for the enabled event flags. Register 0x07
and Register 0x08 determine the pin to which each event flag is
routed. Set Register 0x07 and Register 0x08 to 0 for IRQ1 and set
these registers to 1 for IRQ2.
Ten event flags provide visibility into the device. These flags are
located in the two event flag registers, Register 0x05 and
Register 0x06. The behavior of each event flag is independently
selected in the interrupt enable registers, Register 0x03 and
Register 0x04. When the flag interrupt enable is active, the event
flag latches and triggers an external interrupt. When the flag
interrupt is disabled, the event flag monitors the source signal,
but the IRQ1 and IRQ2 pin remain inactive.
INTERRUPT SERVICE ROUTINE
Interrupt request management starts by selecting the set of
event flags that require host intervention or monitoring. Enable
the events that require host action so that the host is notified
when they occur. For events requiring host intervention
upon IRQx activation, run the following routine to clear an
interrupt request:
INTERRUPT WORKING MECHANISM
Figure 49 shows the interrupt related circuitry and how the event
flag signals propagate to the IRQx output. The INTERRUPT_
ENABLE signal represents one bit from the interrupt enable
register. The EVENT_FLAG_SOURCE signal represents one bit
from the event flag register. The EVENT_FLAG_SOURCE signal
represents one of the device signals that can be monitored, such as
the PLL_LOCK signal from the PLL phase detector or the
FIFO_WARNING_1 signal from the FIFO controller.
1.
2.
3.
4.
When an interrupt enable bit is set high, the corresponding event
flag bit reflects a positively tripped version of the EVENT_FLAG_
SOURCE signal; that is, the event flag bit is latched on the rising
edge of the EVENT_FLAG_SOURCE signal. This signal also
asserts the external IRQ pins.
5.
6.
Read the status of the event flag bits that are being
monitored.
Set the interrupt enable bit low so that the unlatched
EVENT_FLAG_SOURCE can be monitored directly.
Perform any actions that may be required to clear the
EVENT_FLAG_SOURCE. In many cases, no specific
actions may be required.
Read the event flag to verify that the actions taken have
cleared the EVENT_FLAG_SOURCE.
Clear the interrupt by writing 1 to the event flag bit.
Set the interrupt enable bits of the events to be monitored.
Note that some EVENT_FLAG_SOURCE signals are latched
signals. These signals are cleared by writing to the corresponding event flag bit. For more information about each of the
event flags, see the Device Configuration Register Map and
Description section.
When an interrupt enable bit is set low, the event flag bit reflects
the present status of the EVENT_FLAG_SOURCE signal, and
the event flag has no effect on the external IRQ pins.
Clear the latched version of an event flag (the INTERRUPT_
SOURCE signal) in one of two ways. The recommended
0
1
EVENT_FLAG
IRQ
EVENT_FLAG_SOURCE
OTHER
INTERRUPT
SOURCES
10930-054
INTERRUPT_ENABLE
INTERRUPT_
SOURCE
WRITE_1_TO_EVENT_FLAG
DEVICE_RESET
Figure 49. Simplified Schematic of IRQ Circuitry
Rev. 0 | Page 34 of 64
Data Sheet
AD9142
TEMPERATURE SENSOR
The AD9142 has a diode-based temperature sensor for measuring
the temperature of the die. The temperature reading is accessed
using Register 0x1D and Register 0x1E. The temperature of the
die can be calculated as
T DIE =
Estimates of the ambient temperature can be made if the power
dissipation of the device is known. For example, if the device
power dissipation is 800 mW and the measured die temperature
is 50°C, then the ambient temperature can be calculated as
TA = TDIE – PD × θJA = 50 – 0.8 × 20.7 = 33.4°C
( DieTemp [ 15 : 0 ] − 41, 237 )
106
where TDIE is the die temperature in degrees Celsius. The
temperature accuracy is ±7°C typical over the +85°C to −40°C
range with one point temperature calibration against a known
temperature. A typical plot of the die temperature vs. die
temperature code readback is shown in Figure 50.
51000
where:
TA is the ambient temperature in degrees Celsius.
θJA is the thermal resistance from junction to ambient of the
AD9142 as shown in Table 8.
To use the temperature sensor, it must be enabled by setting Bit 0,
Register 0x1C to 1. In addition, to get accurate readings, the die
temperature control register (Register 0x1C) should be set to 0x03.
47000
45000
43000
41000
39000
37000
35000
–40 –30 –20 –10
0
10
20
30
40
50
60
70
80
90
TEMPERATURE (°C)
10930-201
DIE CODE READBACK
49000
Figure 50. Die Temperature vs. Die Temperature Code Readback
Rev. 0 | Page 35 of 64
AD9142
Data Sheet
DAC INPUT CLOCK CONFIGURATIONS
The AD9142 DAC sample clock (DACCLK) can be sourced
directly or by clock multiplying. Clock multiplying employs the
on-chip phase-locked loop (PLL) that accepts a reference clock
operating at a submultiple of the desired DACCLK rate. The
PLL then multiplies the reference clock up to the desired DACCLK
frequency, which can then be used to generate all of the internal
clocks required by the DAC. The clock multiplier provides a
high quality clock that meets the performance requirements of
most applications. Using the on-chip clock multiplier removes
the burden of generating and distributing the high speed DACCLK.
The second mode bypasses the clock multiplier circuitry and lets
DACCLK be sourced directly to the DAC core. This mode lets the
user source a very high quality clock directly to the DAC core.
DRIVING THE DACCLK AND REFCLK INPUTS
The DACCLK and REFCLK differential inputs share similar
clock receiver input circuitry. Figure 51 shows a simplified circuit
diagram of the input. The on-chip clock receiver has a differential
input impedance of about 10 kΩ. It is self biased to a commonmode voltage of about 1.25 V. The inputs can be driven by
differential PECL or LVDS drivers with ac coupling between the
clock source and the receiver.
1~100nF
AD9142
DACCLKP/
REFP/SYNCP
Direct clocking with a low noise clock produces the lowest noise
spectral density at the DAC outputs. To select the differential
CLK inputs as the source for the DAC sampling clock, set the
PLL enable bit (Register 0x12[7]) to 0. This powers down the
internal PLL clock multiplier and selects the input from the
DACCLKP and DACCLKN pins as the source for the internal
DAC sampling clock. The REFCLK input can remain floating.
The device also has clock duty cycle correction circuitry and
differential input level correction circuitry. Enabling these circuits
can provide improved performance in some cases. The control
bits for these functions are in Register 0x10 and Register 0x11.
CLOCK MULTIPLICATION
The on-chip PLL clock multiplier circuit generates the DAC
sample rate clock from a lower frequency reference clock. When
the PLL enable bit (Register 0x12[7]) is set to 1, the clock
multiplication circuit generates the DAC sampling clock from
the lower rate REFCLK input and the DACCLK input is left
floating. The functional diagram of the clock multiplier is
shown in Figure 52.
The clock multiplication circuit operates such that the VCO
outputs a frequency, fVCO, equal to the REFCLK input signal
frequency multiplied by N1 × N0. N1 is the divide ratio of the
loop divider; N0 is the divide ratio of the VCO divider.
fVCO = fREFCLK × (N1 × N0)
5kΩ
1~100nF
5kΩ
DACCLKN/
REFN/SYNCN
The DAC sample clock frequency, fDACCLK, is equal to
1.25V
fDACCLK = fREFCLK × N1
10930-055
100Ω
Figure 51. Clock Receiver Input Simplified Equivalent Circuit
The minimum input drive level to the differential clock input is
100 mV p-p differential. The optimal performance is achieved
when the clock input signal is between 800 mV p-p differential
and 1.6 V p-p differential. Whether using the on-chip clock
multiplier or sourcing the DACCLK directly, the input clock
signal to the device must have low jitter and fast edge rates to
optimize the DAC noise performance.
REFP/SYNCP
(PIN 2)
REFN/SYNCN
(PIN 3)
PHASE
FREQUENCY
DETECTION
The output frequency of the VCO must be chosen to keep fVCO
in the optimal operating range of 1.0 GHz to 2.1 GHz. It is
important to select a frequency of the reference clock and values
of N1 and N0 so that the desired DACCLK frequency can be
synthesized and the VCO output frequency is in the correct range.
ADC
PLL CHARGE
PUMP CURRENT
REG 0x14[4:0]
PLL LOOP BW
REG 0x14[7:5]
CHARGE
PUMP
ON-CHIP
LOOP FILTER
VCO
(1GHz~2.1GHz)
LOOP DIVIDER
REG 0x15[1:0]
VCO DIVIDER
REG 0x15[3:2]
DIVIDE BY
2, 4, 8, OR 16
DIVIDE BY
1, 2, OR 4
DACCLKN
(PIN 62)
VCO CONTROL
VOLTAGE
REG 0x16[3:0]
DACCLK
DACCLKP
(PIN 61)
PLL ENABLE
REG 0x12[7]
Figure 52. PLL Clock Multiplication Circuit
Rev. 0 | Page 36 of 64
10930-056
RECOMMENDED
EXTERNAL
CIRCUITRY
DIRECT CLOCKING
Data Sheet
AD9142
PLL SETTINGS
61
The PLL circuitry requires three settings to be programmed to
their nominal values. The PLL values shown in Table 21 are the
recommended settings for these parameters.
53
57
49
45
PLL BAND
41
Table 21. PLL Settings
Register
Address
0x14[7:5]
0x14[4:0]
0x15[4]
Optimal Setting
(Binary)
111
00111
0
33
29
25
21
17
13
9
5
1
950
CONFIGURING THE VCO TUNING BAND
The PLL VCO has a valid operating range from approximately
1.0 GHz to 2.1 GHz covered in 64 overlapping frequency bands.
For any desired VCO output frequency, there may be several
valid PLL band select values. The frequency bands of a typical
device are shown in Figure 53. Device-to-device variations and
operating temperature affect the actual band frequency range.
Therefore, it is required that the optimal PLL band select value
be determined for each individual device.
1150
1350
1550
1750
1950
VCO FREQUENCY (MHz)
2150
10930-057
PLL SPI Control
Register
PLL Loop Bandwidth
PLL Charge Pump Current
PLL Cross Control Enable
37
Figure 53. PLL Lock Range for a Typical Device
MANUAL VCO BAND SELECT
The device includes a manual band select mode (PLL auto
manual enable, Register 0x12[6] = 1) that lets the user select the
VCO tuning band. In manual mode, the VCO band is set
directly with the value written to the manual VCO band bits
(Register 0x12[5:0]).
AUTOMATIC VCO BAND SELECT
PLL ENABLE SEQUENCE
The device has an automatic VCO band select feature on chip.
Using the automatic VCO band select feature is a simple and
reliable method of configuring the VCO frequency band. This
feature is enabled by starting the PLL in manual mode, and then
placing the PLL in autoband select mode by setting Register
0x12 to a value of 0xC0 and then to a value of 0x80. When these
values are written, the device executes an automated routine
that determines the optimal VCO band setting for the device.
To enable the PLL in automatic or manual mode properly, the
following sequence must be followed:
The setting selected by the device ensures that the PLL remains
locked over the full −40°C to +85°C operating temperature
range of the device without further adjustment. The PLL
remains locked over the full temperature range even if the
temperature during initialization is at one of the temperature
extremes.
Automatic Mode Sequence
1.
2.
3.
4.
5.
6.
Configure the loop divider and the VCO divider registers
for the desired divide ratios.
Set 00111b to PLL charge pump current and 111b to PLL
loop bandwidth for the best performance.
Set the PLL mode to manual using Register 0x12[6] = 1b.
Enable the PLL using Register 0x12[7] = 1b.
Set the PLL mode to automatic using Register 0x12[6] = 0b.
Enable the PLL using Register 0x12[7] = 1b.
Manual Mode
1.
2.
3.
4.
5.
6.
Rev. 0 | Page 37 of 64
Configure the loop divider and the VCO divider registers
for the desired divide ratios.
Set 00111b to PLL charge pump current and 111b to PLL
loop bandwidth for the best performance.
Select the desired band.
Set the PLL mode to manual using Register 0x12[6] = 1b.
Enable the PLL using Register 0x12[7] = 1b.
Enable the PLL one more time using Register 0x12[7] = 1b.
AD9142
Data Sheet
ANALOG OUTPUTS
Figure 54 shows a simplified block diagram of the transmit path
DACs. The DAC core consists of a current source array, a switch
core, digital control logic, and full-scale output current control.
The DAC full-scale output current (IOUTFS) is nominally 20 mA.
The output currents from the IOUT1P/IOUT2P and IOUT1N/
IOUT2N pins are complementary, meaning that the sum of the
two currents always equals the full-scale current of the DAC.
The digital input code to the DAC determines the effective
differential current delivered to the load.
I DAC FS ADJUST
REG 0x18, 0x19
CURRENT
SCALING
15
IOUT2N
IOUT2P
0
Q DAC FS ADJUST
REG 0x1A, 0x1B
Figure 54. Simplified Block Diagram of DAC Core
The DAC has a 1.2 V band gap reference with an output impedance of 5 kΩ. The reference output voltage appears on the REFIO
pin. When using the internal reference, decouple the REFIO pin
to AVSS with a 0.1 µF capacitor. Use the internal reference only
for external circuits that draw dc currents of 2 µA or less. For
dynamic loads or static loads greater than 2 µA, buffer the REFIO
pin. If desired, the internal reference can be overdriven by
applying an external reference (from 1.10 V to 1.30 V) to the
REFIO pin.
A 10 kΩ external resistor, RSET, must be connected from the
FSADJ pin to AVSS. This resistor, together with the reference
control amplifier, sets up the correct internal bias currents for
the DAC. Because the full-scale current is inversely proportional to
this resistor, the tolerance of RSET is reflected in the full-scale
output amplitude.
The full-scale current equation, where the DAC gain is set
individually for the Q and IDACs in Register 0x40 and Register
0x44, respectively, is as follows:
0
200
400
600
800
DAC GAIN CODE
1000
10930-059
5
Q DAC
VREF 
3

×  72 +  × DAC gain  
RSET 

 16
20
10
IOUT1N
10kΩ
RSET
I FS =
25
I DAC
5kΩ
FSADJ
30
IOUT1P
REFIO
0.1µF
35
10930-058
1.2V
For nominal values of VREF (1.2 V), RSET (10 kΩ), and DAC gain
(512), the full-scale current of the DAC is typically 20.16 mA. The
DAC full-scale current can be adjusted from 8.64 mA to 31.68 mA
by setting the DAC gain parameter, as shown in Figure 55.
IFS (mA)
TRANSMIT DAC OPERATION
Figure 55. DAC Full-Scale Current vs. DAC Gain Code
Transmit DAC Transfer Function
The output currents from the IOUT1P/IOUT2P and IOUT1N/
IOUT2N pins are complementary, meaning that the sum of the
two currents always equals the full-scale current of the DAC. The
digital input code to the DAC determines the effective differential current delivered to the load. IOUT1P/IOUT2P provide
maximum output current when all bits are high. The output
currents vs. DACCODE for the DAC outputs is expressed as
DACCODE 
I OUTP = 
 × I OUTFS
2N

IOUTN = IOUTFS – IOUTP
(1)
(2)
where DACCODE = 0 to 2N − 1.
Transmit DAC Output Configurations
The optimum noise and distortion performance of the AD9142
is realized when it is configured for differential operation. The
common-mode rejection of a transformer or differential amplifier
significantly reduces the common-mode error sources of the DAC
outputs. These common-mode error sources include even-order
distortion products and noise. The enhancement in distortion
performance becomes more significant as the frequency content of
the reconstructed waveform increases and/or its amplitude
increases. This is due to the first-order cancellation of various
dynamic common-mode distortion mechanisms, digital feedthrough, and noise.
Rev. 0 | Page 38 of 64
Data Sheet
AD9142
Figure 56 shows the most basic DAC output circuitry. A pair of
resistors, RO, convert each of the complementary output currents to
a differential voltage output, VOUT. Because the current outputs
of the DAC are high impedance, the differential driving point
impedance of the DAC outputs, ROUT, is equal to 2 × RO. See
Figure 57 for the output voltage waveforms.
ADL537x
67
IOUT1P
IBBP
RBIP
50Ω
66
RBIN
50Ω
IBBN
IOUT1N
59
+
IOUT2N
QBBN
RBQN
50Ω
RO
VOUTI
RO
RLI
100Ω
RBQP
50Ω
58
VIN –
RLQ
100Ω
QBBP
IOUT2P
IOUT1N
10930-062
VIP
IOUT1P
AD9142
Figure 58. Typical Interface Circuitry Between the AD9142 and the ADL537x
Family of Modulators
VQP +
IOUT2P
The baseband inputs of the ADL537x family require a dc bias
of 500 mV. The nominal midscale output current on each output of
the DAC is 10 mA (one-half the full-scale current). Therefore,
a single 50 Ω resistor to ground from each of the DAC outputs
results in the desired 500 mV dc common-mode bias for the
inputs to the ADL537x. The addition of the load resistor in
parallel with the modulator inputs reduces the signal level. The
peak-to-peak voltage swing of the transmitted signal is
RO
10930-060
VOUTQ
RO
VQN –
IOUT2N
Figure 56. Basic Transmit DAC Output Circuit
+VPEAK
VSIGNAL = I FS ×
VCM
VN
VP
(2 × R B × R L )
(2 × R B + R L )
Baseband Filter Implementation
0
Most applications require a baseband anti-imaging filter between
the DAC and the modulator to filter out Nyquist images and
broadband DAC noise. The filter can be inserted between the
I-V resistors at the DAC output and the signal level setting resistor
across the modulator input. This configuration establishes the
input and output impedances for the filter.
10930-061
VOUT
Figure 59 shows a fifth-order, low-pass filter. A common-mode
choke is placed between the I-V resistors and the remainder of
the filter to remove the common-mode signal produced by the
DAC and to prevent the common-mode signal from being
converted to a differential signal, which can appear as unwanted
spurious signals in the output spectrum. Splitting the first filter
capacitor into two and grounding the center point creates a
common-mode low-pass filter, which provides additional
common-mode rejection of high frequency signals. A purely
differential filter can pass common-mode signals.
Figure 57. Output Voltage Waveforms
The common-mode signal voltage, VCM, is calculated as
VCM =
I FS
× RO
2
The peak output voltage, VPEAK, is calculated as
VPEAK = IFS × RO
In this circuit configuration, the single-ended peak voltage is
the same as the peak differential output voltage.
INTERFACING TO MODULATORS
For more details about interfacing the AD9142 DAC to an IQ
modulator, refer to the Circuits from the Lab CN-0205, Interfacing
the ADL5375 I/Q Modulator to the AD9122 Dual Channel,
1.2 GSPS High Speed DAC on the Analog Devices website.
The AD9142 interfaces to the ADL537x family of modulators
with a minimal number of components. An example of the
recommended interface circuitry is shown in Figure 58.
50Ω
AD9142
22pF
33nH
33nH
33nH
33nH
3.6pF
50Ω
3pF
6pF
22pF
140Ω ADL537x
3pF
Figure 59. DAC Modulator Interface with Fifth-Order, Low-Pass Filter
Rev. 0 | Page 39 of 64
10930-063
–VPEAK
AD9142
Data Sheet
REDUCING LO LEAKAGE AND UNWANTED
SIDEBANDS
Analog quadrature modulators can introduce unwanted signals
at the local oscillator (LO) frequency due to dc offset voltages in
the I and Q baseband inputs, as well as feedthrough paths from
the LO input to the output. The LO feedthrough can be nulled
by applying the correct dc offset voltages at the DAC output
using the digital dc offset adjustments (Register 0x3B through
Register 0x3E).
(Register 0x37 and Register 0x38) and the DAC FS adjust
registers (Register 0x18 through Register 0x1B) can be used to
calibrate the I and Q transmit paths to optimize sideband
suppression.
For more information about suppressing LO leakage and
sideband image, refer to Application Note AN-1039, Correcting
Imperfections in IQ Modulators to Improve RF Signal Fidelity
and Application Note AN-1100, Wireless Transmitter IQ Balance
and Sideband Suppression from the Analog Devices website.
Effective sideband suppression requires both gain and phase
matching of the I and Q signals. The I/Q phase adjust registers
Rev. 0 | Page 40 of 64
Data Sheet
AD9142
EXAMPLE START-UP ROUTINE
To ensure reliable start-up of the AD9142, certain sequences
must be followed. This section shows an example start-up
routine.
/* Configure PLL */
0x14 → 0xE3 /* Configure PLL loop BW and charge
pump current */
0x15 → 0xC2 /* Configure VCO divider and Loop
divider */
Device Configuration and Start-Up Sequence
•
•
•
•
•
•
0x12 → 0xC0 /*Enable the PLL */
fDATA = 200 MHz, interpolation is 8×.
Input data is baseband data.
fOUT = 350 MHz.
PLL is enabled, fREF = 200 MHz.
Fine NCO is enabled, inverse sinc filter is enabled.
A delay line-based mode is used with an interface delay
setting of 0.
0x12 → 0x80
/* Configure Data Interface */
0x5E → 0x00 /* Delay setting 0 */
0x5F → 0x08 /* Enable the delay line */
/* Configure Interpolation filter */
Derived PLL Settings
0x28 → 0x03 /* 8× interpolation */
The following PLL settings can be derived from the device
configuration:
•
•
•
•
/* Reset FIFO */
fDAC = 200 × 8 = 1600 MHz.
fVCO= fDAC = 1600 MHz (1 GHz < fVCO < 2 GHz).
VCO divider = fVCO/fDAC = 1.
Loop divider = fDAC/fREF = 8.
0x25 → 0x01
Read 0x25[1] /* Expect 1b if the FIFO reset is
complete */
Read 0x24 /* The readback should be one of the
three values: 0x37, 0x40, or 0x41 */
Derived NCO Settings
The following NCO settings can be derived from the device
configuration:
•
•
•
/* Configure NCO */
0x27→ 0x40 /* Enable NCO */
fDAC = 200 × 8 = 1600 MHz.
fCARRIER = fOUT = 350 MHz.
FTW = fCARRIER/fDAC × 232 = 0x38000000.
0x31 → 0x00
0x32 → 0x00
0x33 → 0x00
Start-Up Sequence
1.
2.
3.
4.
5.
Power up the device (no specific power supply sequence is
required).
Apply stable DAC clock.
Apply stable DCI clock.
Feed stable input data.
Issue H/W reset (optional).
/* Device configuration register write
sequence. Must be written in sequence for every
device after reset*/
0x00 → 0x20 /* Issue software reset */
0x34 → 0x38
0x30 → 0x01
Read 0x30[1] /* Expect 1b if the NCO update is
complete */
/* Enable Inverse SINC filter */
0x27 → 0xC0
/* Power up DAC outputs */
0x01 → 0x00
0x20 → 0x01 /* Device Startup Configuration */
0x79 → 0x18 /* Device Startup Configuration */
0x80 → 0xAD /* Device Startup Configuration */
0xE1 → 0x1A /* Device Startup Configuration */
Rev. 0 | Page 41 of 64
AD9142
Data Sheet
DEVICE CONFIGURATION REGISTER MAP AND DESCRIPTION
Table 22. Device Configuration Register Map
Reg
0x00
0x01
0x03
Name
Common
PD_CONTROL
INTERRUPT_
ENABLE0
Bits
[7:0]
[7:0]
[7:0]
Bit 7
Reserved
PD_IDAC
Reserved
Bit 6
SPI_LSB_FIRST
PD_QDAC
ENABLE_
SYNC_LOST
0x04 INTERRUPT_
ENABLE1
0x05 INTERRUPT_
FLAG0
0x06 INTERRUPT_
FLAG1
0x07 IRQ_SEL0
[7:0]
0x08 IRQ_SEL1
[7:0]
0x10 DACCLK_
RECEIVER_
CTRL
0x11 REFCLK_
RECEIVER_CTRL
[7:0] DACCLK_
DUTYCYCLE_
CORRECTION
[7:0] DUTYCYCLE_
CORRECTION
0x12 PLL_CTRL0
[7:0] PLL_ENABLE
0x14 PLL_CTRL2
0x15 PLL_CTRL3
[7:0]
[7:0]
0x16
0x17
0x18
0x19
[7:0] PLL_LOCK
[7:0]
Reserved
[7:0]
[7:0]
PLL_STATUS0
PLL_STATUS1
IDAC_FS_ADJ0
IDAC_FS_ADJ1
Reserved
[7:0] Reserved
SYNC_LOST
SYNC_LOCKED SYNC_DONE
[7:0]
Reserved
[7:0] Reserved
SEL_SYNC_
LOST
SEL_SYNC_
LOCKED
Reserved
Reserved
Reserved
AUTO_
MANUAL_SEL
PLL_LOOP_BW
DIGLOGIC_DIVIDER
Reserved
[7:0]
0x26 DATA_
FORMAT_SEL
0x27 DATAPATH_
CTRL
[7:0] DATA_
FORMAT
[7:0] INVSINC_
ENABLE
Bit 1
Bit 0
PD_DACCLK
PD_FRAME
ENABLE_OVER_ ENABLE_
DACOUT_
THRESHOLD
MUTED
ENABLE_FIFO_ ENABLE_FIFO_ ENABLE_FIFO_
UNDERFLOW OVERFLOW
WARNING
PLL_LOST
PLL_LOCKED OVER_
DACOUT_
THRESHOLD
MUTED
FIFO_
FIFO_OVERFIFO_
UNDERFLOW FLOW
WARNING
SEL_PLL_LOST
SEL_PLL_
SEL_OVER_
SEL_DACOUT
LOCKED
THRESHOLD
_MUTED
SEL_FIFO_
SEL_FIFO_
SEL_FIFO_
UNDERFLOW OVERFLOW
WARNING
DACCLK_CROSSPOINT_LEVEL
REFCLK_CROSSPOINT_LEVEL
PLL_MANUAL_BAND
PLL_CP_CURRENT
VCO_DIVIDER
CROSSPOINT_
CTRL_EN
LOOP_DIVIDER
VCO_CTRL_VOLTAGE_READBACK
PLL_BAND_READBACK
IDAC_FULLSCALE_ADJUST_LSB
Reserved
IDAC_FULLSCALE_ADJUST_
MSB
QDAC_FULLSCALE_ADJUST_LSB
Reserved
QDAC_FULLSCALE_ADJUST_
MSB
FS_CURRENT
REF_CURRENT
DIE_TEMP_
SENSOR_EN
DIE_TEMP_LSB
DIE_TEMP_MSB
CHIP_ID
INTERRUPT_CONFIGURATION
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
Bit 2
Reserved
PD_DEVICE
ENABLE_PLL_
LOCKED
Reserved
[7:0] Reserved
0x22 FRAME_RST_
CTRL
0x23 FIFO_LEVEL_
CONFIG
0x24 FIFO_LEVEL_
READBACK
0x25 FIFO_CTRL
SEL_SYNC_
DONE
DACCLK_
CROSSPOINT_
CTRL_ENABLE
REFCLK_
CROSSPOINT_
CTRL_ENABLE
0x1A QDAC_FS_ADJ0 [7:0]
0x1B QDAC_FS_ADJ1 [7:0]
0x1C DIE_TEMP_
SENSOR_CTRL
0x1D DIE_TEMP_LSB
0x1E DIE_TEMP_MSB
0x1F CHIP_ID
0x20 INTERRUPT_
CONFIG
0x21 SYNC_CTRL
Bit 5
Bit 4
Bit 3
DEVICE_RESET
PD_DATARCV
Reserved
ENABLE_
ENABLE_
ENABLE_PLL_
SYNC_LOCKED SYNC_DONE
LOST
Reserved
Reserved
[7:0] Reserved
INTEGRAL_FIFO_LEVEL_REQUEST
[7:0] Reserved
INTEGRAL_FIFO_LEVEL_READBACK
[7:0]
FRAME_
RESET_ACK
Reserved
SYNC_CLK_
SYNC_
EDGE_SEL
ENABLE
FRAME_RESET_MODE
EN_CON_
FRAME_RESET
FRACTIONAL_FIFO_LEVEL_REQUEST
Reserved
FRACTIONAL_FIFO_LEVEL_READBACK
Reserved
DATA_PAIRIN
G
NCO_ENABLE
DATA_BUS_
INVERT
IQ_GAIN_ADJ_ IQ_PHASE_
DCOFFSET_
ADJ_ENABLE
ENABLE
FIFO_SPI_
RESET_ACK
Reserved
Reserved
Rev. 0 | Page 42 of 64
FS4_
NCO_SIDEMODULATION_ BAND_SEL
ENABLE
Reset
0x00
0xC0
0x00
RW
RW
RW
RW
0x00
RW
0x00
R
0x00
R
0x00
RW
0x00
RW
0xFF
RW
0xBF
RW
0x00
RW
0xE7 RW
0xC9 RW
0x00
0x00
0xF9
0xE1
R
R
RW
RW
0xF9
0x01
RW
RW
0x02
RW
0x00
0x00
0x0A
0x00
R
R
R
RW
0x00
RW
0x12
RW
0x40
RW
0x00
R
FIFO_SPI_
0x00
RESET_
REQUEST
DATA_BUS_
0x00
WIDTH
SEND_IDATA_ 0x00
TO_QDAC
RW
RW
RW
Data Sheet
0x28 INTERPOLATION_
CTRL
0x29 OVER_
THRESHOLD_
CTRL0
0x2A OVER_
THRESHOLD_
CTRL1
0x2B OVER_
THRESHOLD_
CTRL2
0x2C INPUT_POWER_
READBACK_LSB
0x2D INPUT_POWER_
READBACK_MSB
0x30 NCO_CTRL
AD9142
[7:0]
Reserved
[7:0]
INTERPOLATION_MODE
THRESHOLD_LEVEL_REQUEST_LSB
[7:0]
Reserved
[7:0] ENABLE_
PROTECTION
THRESHOLD_LEVEL_REQUEST_MSB
IQ_DATA_
SWAP
Reserved
[7:0]
SAMPLE_WINDOW_LENGTH
INPUT_POWER_READBACK_LSB
[7:0]
Reserved
[7:0] Reserved
NCO_FRAME_
UPDATE_ACK
INPUT_POWER_READBACK_MSB
SPI_NCO_
PHASE_RST_
ACK
SPI_NCO_
PHASE_
RST_REQ
Reserved
NCO_SPI_
UPDATE_ACK
0x00
RW
0x00
RW
0x00
RW
0x00
RW
0x00
R
0x00
R
NCO_SPI_
0x00
UPDATE_REQ
RW
0x31 NCO_FREQ_
TUNING_
WORD0
0x32 NCO_FREQ_
TUNING_
WORD1
0x33 NCO_FREQ_
TUNING_
WORD2
0x34 NCO_FREQ_
TUNING_
WORD3
0x35 NCO_PHASE_
OFFSET0
0x36 NCO_PHASE_
OFFSET1
0x37 IQ_PHASE_
ADJ0
0x38 IQ_PHASE_
ADJ1
0x3B IDAC_DC_
OFFSET0
0x3C IDAC_DC_
OFFSET1
0x3D QDAC_DC_
OFFSET0
0x3E QDAC_DC_
OFFSET1
0x3F IDAC_GAIN_ADJ
0x40 QDAC_GAIN_
ADJ
0x41 GAIN_STEP_
CTRL0
0x42 GAIN_STEP_
CTRL1
0x43 TX_ENABLE_
CTRL
[7:0]
NCO_FTW0
0x00
RW
[7:0]
NCO_FTW1
0x00
RW
[7:0]
NCO_FTW2
0x00
RW
[7:0]
NCO_FTW3
0x10
RW
[7:0]
NCO_PHASE_OFFSET_LSB
0x00
RW
[7:0]
NCO_PHASE_OFFSET_MSB
0x00
RW
[7:0]
IQ_PHASE_ADJ_LSB
0x00
RW
RW
0x44 DAC_OUTPUT_
CTRL
[7:0] DAC_OUTPUT_
CTRL_EN
[7:0]
Reserved
IQ_PHASE_ADJ_MSB
[7:0]
IDAC_DC_OFFSET_LSB
0x00
0
0x00
[7:0]
IDAC_DC_OFFSET_MSB
0x00
RW
[7:0]
QDAC_DC_OFFSET_LSB
0x00
RW
[7:0]
QDAC_DC_OFFSET_MSB
0x00
RW
RW
[7:0]
[7:0]
Reserved
Reserved
IDAC_GAIN_ADJ
QDAC_GAIN_ADJ
0x20
0x20
RW
RW
[7:0]
Reserved
RAMP_UP_STEP
0x01
RW
RAMP_DOWN_STEP
0x01
RW
TXENABLE_
0x07
POWER_
DOWN_EN
FIFO_ERROR_ 0x8F
SHUTDOWN_
EN
RW
[7:0] DAC_OUTPUT_ DAC_OUTPUT_
STATUS
ON
[7:0]
0x5E DATA_RX_CTRL0 [7:0]
0x5F DATA_RX_CTRL1 [7:0]
0x79 DEVICE_
[7:0]
CONFIG0
0x7F Version
[7:0]
0x80 DEVICE_
[7:0]
CONFIG1
0xE1 DEVICE_
[7:0]
CONFIG2
Reserved
Reserved
Reserved
TXENABLE_
GAINSTEP_EN
FIFO_WARNING_ OVERSHUTDOWN_EN THRESHOLD_
SHUTDOWN_
EN
DLY_TAP_LSB
DLYLINE_EN
DEVICE_CONFIGURATION0
TXENABLE_
SLEEP_EN
Reserved
RW
0xFF
0x07
0x00
RW
RW
RW
Version
DEVICE_CONFIGURATION1
0x05
0x00
R
RW
DEVICE_CONFIGURATION2
0x00
RW
Rev. 0 | Page 43 of 64
DLY_TAP_MSB
AD9142
Data Sheet
SPI CONFIGURE REGISTER
Address: 0x00, Reset: 0x00, Name: Common
Table 23. Bit Descriptions for Common
Bits
6
Bit Name
SPI_LSB_FIRST
Settings
0
1
5
DEVICE_RESET
Description
Serial port communication, MSB-first or LSB-first selection.
MSB first.
LSB first.
The device resets when 1 is written to this bit. DEVICE_RESET is a self clear bit.
After the reset, the bit returns to 0 automatically. The readback is always 0.
Reset
0x0
Access
RW
0x0
RW
Reset
0x1
Access
RW
0x1
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
Reset
0x0
0x0
0x0
0x0
0x0
0x0
0x0
Access
RW
RW
RW
RW
RW
RW
RW
Reset
0x0
0x0
0x0
Access
RW
RW
RW
POWER-DOWN CONTROL REGISTER
Address: 0x01, Reset: 0xC0, Name: PD_CONTROL
Table 24. Bit Descriptions for PD_CONTROL
Bits
7
Bit Name
PD_IDAC
6
PD_QDAC
5
PD_DATARCV
2
PD_DEVICE
1
PD_DACCLK
0
PD_FRAME
Settings
Description
The IDAC is powered down when PD_IDAC is set to 1. This bit powers down
only the analog portion of the IDAC. The IDAC digital data path is not affected.
The QDAC is powered down when PD_QDAC is set to 1. This bit powers down only
the analog portion of the QDAC. The QDAC digital data path is not affected.
The data interface circuitry is powered down when PD_DATARCV is set to 1.
This bit powers down the data interface and the write side of the FIFO.
The bandgap circuitry is powered down when set to 1. This bit powers down
the entire chip.
The DAC clocking powers down when PD_DEVICE is set to 1. This bit powers down
the DAC clocking path and, thus, the majority of the digital functions.
The frame receiver powers down when PD_FRAME is set to 1. The frame signal
is internally pulled low. Set to 1 when frame is not used.
INTERRUPT ENABLE0 REGISTER
Address: 0x03, Reset: 0x00, Name: INTERRUPT_ENABLE0
Table 25. Bit Descriptions for INTERRUPT_ENABLE0
Bits
6
5
4
3
2
1
0
Bit Name
ENABLE_SYNC_LOST
ENABLE_SYNC_LOCKED
ENABLE_SYNC_DONE
ENABLE_PLL_LOST
ENABLE_PLL_LOCKED
ENABLE_OVER_THRESHOLD
ENABLE_DACOUT_MUTED
Settings
Description
Enable interrupt for sync lost.
Enable interrupt for sync lock.
Enable interrupt for sync done.
Enable interrupt for PLL lost.
Enable interrupt for PLL locked.
Enable interrupt for overthreshold.
Enable interrupt for DACOUT muted.
INTERRUPT ENABLE1 REGISTER
Address: 0x04, Reset: 0x00, Name: INTERRUPT_ENABLE1
Table 26. Bit Descriptions for INTERRUPT_ENABLE1
Bits
2
1
0
Bit Name
ENABLE_FIFO_UNDERFLOW
ENABLE_FIFO_OVERFLOW
ENABLE_FIFO_WARNING
Settings
Description
Enable interrupt for FIFO underflow.
Enable interrupt for FIFO overflow.
Enable interrupt for FIFO warning.
Rev. 0 | Page 44 of 64
Data Sheet
AD9142
INTERRUPT FLAG0 REGISTER
Address: 0x05, Reset: 0x00, Name: INTERRUPT_FLAG0
Table 27. Bit Descriptions for INTERRUPT_FLAG0
Bits
6
5
4
3
2
1
Bit Name
SYNC_LOST
SYNC_LOCKED
SYNC_DONE
PLL_LOST
PLL_LOCKED
OVER_THRESHOLD
0
DACOUT_MUTED
Settings
Description
SYNC_LOST is set to 1 when sync is lost.
SYNC_LOCKED is set to 1 when sync is locked.
SYNC_DONE is set to 1 when sync is done.
PLL_LOST is set to 1 when PLL loses lock.
PLL_LOCKED is set to 1 when PLL is locked.
OVER_THRESHOLD is set to 1 when input power is
overthreshold.
DACOUT_MUTED is set to 1 when the DAC output is muted
(midscale dc).
Reset
0x0
0x0
0x0
0x0
0x0
0x0
Access
R
R
R
R
R
R
0x0
R
Description
FIFO_UNDERFLOW is set to 1 when the FIFO read pointer
catches the FIFO write pointer.
FIFO_OVERFLOW is set to 1 when the FIFO write pointer
catches the FIFO read pointer.
FIFO_WARNING is set to 1 when the FIFO is one slot from
empty (≤1) or full (≥6).
Reset
0x0
Access
R
0x0
R
0x0
R
0
1
Description
Selects the IRQ1 pin.
Selects the IRQ2 pin.
Reset
0x0
Access
RW
INTERRUPT FLAG1 REGISTER
Address: 0x06, Reset: 0x00, Name: INTERRUPT_FLAG1
Table 28. Bit Descriptions for INTERRUPT_FLAG1
Bits
2
Bit Name
FIFO_UNDERFLOW
1
FIFO_OVERFLOW
0
FIFO_WARNING
Settings
INTERRUPT SELECT0 REGISTER
Address: 0x07, Reset: 0x00, Name: IRQ_SEL0
Table 29. Bit Descriptions for IRQ_SEL0
Bits
6
Bit Name
SEL_SYNC_LOST
Settings
5
SEL_SYNC_LOCKED
0
1
Selects the IRQ1 pin.
Selects the IRQ2 pin.
0x0
RW
4
SEL_SYNC_DONE
0
1
Selects the IRQ1 pin.
Selects the IRQ2 pin.
0x0
RW
3
SEL_PLL_LOST
0
1
Selects the IRQ1 pin.
Selects the IRQ2 pin.
0x0
RW
2
SEL_PLL_LOCKED
0
1
Selects the IRQ1 pin.
Selects the IRQ2 pin.
0x0
RW
1
SEL_OVER_THRESHOLD
0
1
Selects the IRQ1 pin.
Selects the IRQ2 pin.
0x0
RW
0
SEL_DACOUT_MUTED
0
1
Selects the IRQ1 pin.
Selects the IRQ2 pin.
0x0
RW
Rev. 0 | Page 45 of 64
AD9142
Data Sheet
INTERRUPT SELECT1 REGISTER
Address: 0x08, Reset: 0x00, Name: IRQ_SEL1
Table 30. Bit Descriptions for IRQ_SEL1
Bits
2
Bit Name
SEL_FIFO_UNDERFLOW
1
0
Settings
0
1
Description
Selects the IRQ1 pin.
Selects the IRQ2 pin.
Reset
0x0
Access
RW
SEL_FIFO_OVERFLOW
0
1
Selects the IRQ1 pin.
Selects the IRQ2 pin.
0x0
RW
SEL_FIFO_WARNING
0
1
Selects the IRQ1 pin.
Selects the IRQ2 pin.
0x0
RW
Reset
0x1
Access
RW
0x1
RW
0x1F
RW
Reset
0x0
Access
RW
0x0
RW
0x1F
RW
DAC CLOCK RECEIVER CONTROL REGISTER
Address: 0x10, Reset: 0xFF, Name: DACCLK_RECEIVER_CTRL
Table 31. Bit Descriptions for DACCLK_RECEIVER_CTRL
Bits
7
Bit Name
DACCLK_DUTYCYCLE_CORRECTION
5
DACCLK_CROSSPOINT_CTRL_ENABLE
[4:0]
DACCLK_CROSSPOINT_LEVEL
Settings
Description
Enables duty cycle correction at the DACCLK input. For
best performance, the default and recommended status
is turned on.
Enables crosspoint control at the DACCLK input. For best
performance, the default and recommended status is
turned on.
A twos complement value. For best performance, it is
recommended to set DACCLK_CROSSPOINT_LEVEL to
the default value.
Highest crosspoint.
Lowest crosspoint.
01111
11111
REF CLOCK RECEIVER CONTROL REGISTER
Address: 0x11, Reset: 0xBF, Name: REFCLK_RECEIVER_CTRL
Table 32. Bit Descriptions for REFCLK_RECEIVER_CTRL
Bits
7
Bit Name
DUTYCYCLE_CORRECTION
5
REFCLK_CROSSPOINT_CTRL_ENABLE
[4:0]
REFCLK_CROSSPOINT_LEVEL
Settings
01111
11111
Description
Enables duty cycle correction at the REFCLK input. For
best performance, the default and recommended status
is turned off.
Enables crosspoint control at the REFCLK input. For best
performance, the default and recommended status is
turned off.
A twos complement value. For best performance, it is
recommended to set REFCLK_CROSSPOINT_LEVEL to
the default value.
Highest crosspoint.
Lowest crosspoint.
Rev. 0 | Page 46 of 64
Data Sheet
AD9142
PLL CONTROL REGISTER
Address: 0x12, Reset: 0x00, Name: PLL_CTRL0
Table 33. Bit Descriptions for PLL_CTRL0
Bits
7
6
Bit Name
PLL_ENABLE
AUTO_MANUAL_SEL
Settings
0
1
[5:0]
PLL_MANUAL_BAND
000000
111111
Description
Enables PLL clock multiplier.
PLL band selection mode.
Automatic mode.
Manual mode.
PLL band setting in manual mode. 64 bands in total, covering a 1 GHz to
2.1 GHz VCO range.
Lowest band (1 GHz).
Highest band (2.1 GHz).
Reset
0x0
0x0
Access
RW
RW
0x00
RW
Reset
0x7
Access
RW
0x07
RW
Reset
0x3
Access
RW
0x0
RW
0x2
RW
0x1
RW
PLL CONTROL REGISTER
Address: 0x14, Reset: 0xE7, Name: PLL_CTRL2
Table 34. Bit Descriptions for PLL_CTRL2
Bits
[7:5]
Bit Name
PLL_LOOP_BW
Settings
0x00
0x1F
[4:0]
PLL_CP_CURRENT
0x00
0x1F
Description
Selects the PLL loop filter bandwidth. The default and recommended
setting is 111 for optimal PLL performance.
Lowest setting.
Highest setting.
Sets nominal PLL charge pump current. The default and recommended
setting is 00111 for optimal PLL performance.
Lowest setting.
Highest setting.
PLL CONTROL REGISTER
Address: 0x15, Reset: 0xC9, Name: PLL_CTRL3
Table 35. Bit Descriptions for PLL_CTRL3
Bits
[7:6]
Bit Name
DIGLOGIC_DIVIDER
Settings
00
01
10
11
4
CROSSPOINT_CTRL_EN
[3:2]
VCO_DIVIDER
00
01
10
11
[1:0]
LOOP_DIVIDER
00
01
10
11
Description
REFCLK to PLL digital clock divide ratio. The PLL digital clock drives the
internal PLL logics. The divide ratio must be set to ensure that the PLL
digital clock is below 75 MHz.
fREFCLK/fDIG = 2.
fREFCLK/fDIG = 4.
fREFCLK/fDIG = 8.
fREFCLK/fDIG = 16.
Enable loop divider crosspoint control. The default and recommended
setting is turned off (0) for optimal PLL performance.
PLL VCO divider. This divider determines the ratio of the VCO frequency
to the DACCLK frequency.
fVCO/fDACCLK = 1.
fVCO/fDACCLK = 2.
fVCO/fDACCLK = 4.
fVCO/fDACCLK = 4.
PLL loop divider. This divider determines the ratio of the DACCLK
frequency to the REFCLK frequency.
fDACCLK/fREFCLK = 2.
fDACCLK/fREFCLK = 4.
fDACCLK/fREFCLK = 8.
fDACCLK/fREFCLK = 16.
Rev. 0 | Page 47 of 64
AD9142
Data Sheet
PLL STATUS REGISTER
Address: 0x16, Reset: 0x00, Name: PLL_STATUS0
Table 36. Bit Descriptions for PLL_STATUS0
Bits
7
[3:0]
Bit Name
PLL_LOCK
VCO_CTRL_VOLTAGE_READBACK
Settings
1111
0111
0000
Description
PLL clock multiplier output is stable.
VCO control voltage readback. A binary value.
The highest VCO control voltage.
The mid value when a proper VCO band is selected. When
the PLL is locked, selecting a higher VCO band decreases this
value and selecting a lower VCO band increases this value.
The lowest VCO control voltage.
Reset
0x0
0x0
Access
R
R
Description
Indicates the VCO band currently selected.
Reset
0x00
Access
R
Description
See Register 0x19.
Reset
0xF9
Access
RW
Description
IDAC full-scale adjust, Bits[9:0] sets the full-scale current of
the IDAC. The full-scale current can be adjusted from 8.64 mA
to 31.68 mA. The default value (0x1F9) sets the full-scale
current to 20 mA.
Reset
0x1
Access
RW
Description
See Register 0x1B.
Reset
0xF9
Access
RW
PLL STATUS REGISTER
Address: 0x17, Reset: 0x00, Name: PLL_STATUS1
Table 37. Bit Descriptions for PLL_STATUS1
Bits
[5:0]
Bit Name
PLL_BAND_READBACK
Settings
IDAC FS ADJUST LSB REGISTER
Address: 0x18, Reset: 0xF9, Name: IDAC_FS_ADJ0
Table 38. Bit Descriptions for IDAC_FS_ADJ0
Bits
[7:0]
Bit Name
IDAC_FULLSCALE_ADJUST_LSB
Settings
IDAC FS ADJUST MSB REGISTER
Address: 0x19, Reset: 0xE1, Name: IDAC_FS_ADJ1
Table 39. Bit Descriptions for IDAC_FS_ADJ1
Bits
[1:0]
Bit Name
IDAC_FULLSCALE_ADJUST_MSB
Settings
QDAC FS ADJUST LSB REGISTER
Address: 0x1A, Reset: 0xF9, Name: QDAC_FS_ADJ0
Table 40. Bit Descriptions for QDAC_FS_ADJ0
Bits
[7:0]
Bit Name
QDAC_FULLSCALE_ADJUST_LSB
Settings
Rev. 0 | Page 48 of 64
Data Sheet
AD9142
QDAC FS ADJUST MSB REGISTER
Address: 0x1B, Reset: 0x01, Name: QDAC_FS_ADJ1
Table 41. Bit Descriptions for QDAC_FS_ADJ1
Bits
[1:0]
Bit Name
QDAC_FULLSCALE_ADJUST_MSB
Settings
Description
QDAC full-scale adjust, Bits[9:0] sets the full-scale current of the QDAC.
The full-scale current can be adjusted from 8.64 mA to 31.68 mA. The
default value (0x1F9) sets the full-scale current to 20 mA.
Reset
0x1
Access
RW
Reset
0x0
Access
RW
0x1
RW
0x0
RW
Reset
0x00
Access
R
DIE TEMPERATURE SENSOR CONTROL REGISTER
Address: 0x1C, Reset: 0x02, Name: DIE_TEMP_SENSOR_CTRL
Table 42. Bit Descriptions for DIE_TEMP_SENSOR_CTRL
Bits
[6:4]
Bit Name
FS_CURRENT
Settings
000
001
…
110
111
[3:1]
REF_CURRENT
000
001
…
110
111
0
DIE_TEMP_SENSOR_EN
Description
Temperature sensor ADC full-scale current. Using the default
setting is recommended.
50 μA.
62.5 μA.
125 μA.
137.5 μA.
Temperature sensor ADC reference current. Using the default
setting is recommended.
12.5 μA.
19 μA.
50 μA.
56.5 μA.
Enable the on-chip temperature sensor.
DIE TEMPERATURE LSB REGISTER
Address: 0x1D, Reset: 0x00, Name: DIE_TEMP_LSB
Table 43. Bit Descriptions for DIE_TEMP_LSB
Bits
[7:0]
Bit Name
DIE_TEMP_LSB
Settings
Description
See Register 0x1E.
DIE TEMPERATURE MSB REGISTER
Address: 0x1E, Reset: 0x00, Name: DIE_TEMP_MSB
Table 44. Bit Descriptions for DIE_TEMP_MSB
Bits
[7:0]
Bit Name
DIE_TEMP_MSB
Settings
Description
Die temperature, Bits[15:0] indicate the approximate die temperature.
For more information, see the Temperature Sensor section.
Reset
0x00
Access
R
CHIP ID REGISTER
Address: 0x1F, Reset: 0x0A, Name: CHIP_ID
Table 45. Bit Descriptions for CHIP_ID
Bits
[7:0]
Bit Name
CHIP_ID
Settings
Description
The AD9142 chip ID is 0x0A.
Rev. 0 | Page 49 of 64
Reset
0x0A
Access
R
AD9142
Data Sheet
INTERRUPT CONFIGUATION REGISTER
Address: 0x20, Reset: 0x00, Name: INTERRUPT_CONFIG
Table 46. Bit Descriptions for INTERRUPT_CONFIG
Bits
[7:0]
Bit Name
INTERRUPT_CONFIGURATION
Settings
0x00
0x01
Description
Test mode.
Recommended mode (described in Interrupt Request
Operation section).
Reset
0x00
Access
RW
SYNC CTRL REGISTER
Address: 0x21, Reset: 0x00, Name: SYNC_CTRL
Table 47. Bit Descriptions for SYNC_CTRL
Bits
1
Bit Name
SYNC_CLK_EDGE_SEL
Settings
0
1
0
SYNC_ENABLE
Description
Selects the sampling edge of the DACCLK on the SYNC CLK.
SYNC CLK is sampled by rising edges of DACCLK.
SYNC CLK is sampled by falling edges of DACCLK.
Enables multichip synchronization.
Reset
0x0
Access
RW
0x0
RW
Reset
0x0
Access
R
0x0
RW
0x2
RW
FRAME RESET CTRL REGISTER
Address: 0x22, Reset: 0x12, Name: FRAME_RST_CTRL
Table 48. Bit Descriptions for FRAME_RST_CTRL
Bits
3
Bit Name
FRAME_RESET_ACK
2
EN_CON_FRAME_RESET
Settings
0
1
[1:0]
FRAME_RESET_MODE
00
01
10
11
Description
Frame reset acknowledge. This bit is set to 1 when a valid frame pulse
is received.
Reset mode selection.
Responds to only the first valid frame pulse and resets the FIFO and/or
NCO one time only. This is the default and recommended mode.
Responds to every valid frame pulse and resets the FIFO and/or NCO
accordingly.
These bits determine what is to be reset when the device receives a
valid frame signal.
FIFO only.
NCO only.
FIFO and NCO.
None.
Rev. 0 | Page 50 of 64
Data Sheet
AD9142
FIFO LEVEL CONFIGURATION REGISTER
Address: 0x23, Reset: 0x40, Name: FIFO_LEVEL_CONFIG
Table 49. Bit Descriptions for FIFO_LEVEL_CONFIG
Bits
[6:4]
Bit Name
INTEGRAL_FIFO_LEVEL_REQUEST
Settings
Description
Sets the integral FIFO level. This is the difference between the
read pointer and the write pointer values in the unit of
input data rate (fDATA). The default and recommended FIFO
level is integral level = 4 and fractional level = 0. See the
FIFO Operation section for details.
0.
1.
000
001
…
111
[2:0]
7.
Sets the fractional FIFO level. This is the difference between
the read pointer and the write pointer values in the unit of
DACCLK rate (FDAC). The maximum allowed setting value =
interpolation rate − 1. See the FIFO Operation section for
details.
0.
1.
FRACTIONAL_FIFO_LEVEL_REQUEST
000
001
…
Max
allowed
setting.
Reset
0x4
Access
RW
0x0
RW
Reset
0x0
Access
R
0x0
R
Reset
0x0
0x0
Access
R
RW
001 in 2×.
003 in 4×.
007 in 8×.
FIFO LEVEL READBACK REGISTER
Address: 0x24, Reset: 0x00, Name: FIFO_LEVEL_READBACK
Table 50. Bit Descriptions for FIFO_LEVEL_READBACK
Bits
[6:4]
Bit Name
INTEGRAL_FIFO_LEVEL_READBACK
[2:0]
FRACTIONAL_FIFO_LEVEL_READBACK
Settings
Description
The integral FIFO level read back. The difference between the
overall FIFO level request and readback should be within
two DACCLK cycles. See the FIFO Operation section for
details.
The fractional FIFO level read back. This value should be
used in combination with the readback in Bit[6:4].
FIFO CTRL REGISTER
Address: 0x25, Reset: 0x00, Name: FIFO_CTRL
Table 51. Bit Descriptions for FIFO_CTRL
Bits
1
0
Bit Name
FIFO_SPI_RESET_ACK
FIFO_SPI_RESET_REQUEST
Settings
Description
Acknowledge a serial port initialized FIFO reset.
Initialize a FIFO reset via the serial port.
Rev. 0 | Page 51 of 64
AD9142
Data Sheet
DATA FORMAT SELECT REGISTER
Address: 0x26, Reset: 0x00, Name: DATA_FORMAT_SEL
Table 52. Bit Descriptions for DATA_FORMAT_SEL
Bits
7
Bit Name
DATA_FORMAT
Settings
0
1
6
DATA_PAIRING
0
1
5
DATA_BUS_INVERT
0
1
0
DATA_BUS_WIDTH
0
1
Description
Select binary or twos complement data format.
Input data in twos complement format.
Input data in binary format.
Indicate I/Q data pairing on data input.
I samples are paired with the next Q samples.
I samples are paired with the prior Q samples.
Swap the bit order of the data input port. MSBs become the LSBs:
D[15:0] changes to D[0:15].
The order of the data bits corresponds to the pin descriptions in Table 9.
The order of the data bits is inverted.
Data interface mode. See the LVDS Input Data Ports section for
information about the operation of the different interface modes.
Word mode; 16-bit interface bus width.
Byte mode; 8-bit interface bus width.
Reset
0x0
Access
RW
0x0
RW
0x0
RW
0x0
RW
Reset
0x0
0x0
0x0
0x0
0x0
0x0
Access
RW
RW
RW
RW
RW
RW
0x0
RW
Reset
0x0
Access
RW
DATAPATH CONTROL REGISTER
Address: 0x27, Reset: 0x00, Name: DATAPATH_CTRL
Table 53. Bit Descriptions for DATAPATH_CTRL
Bits
7
6
5
4
2
1
Bit Name
INVSINC_ENABLE
NCO_ENABLE
IQ_GAIN_ADJ_DCOFFSET_ENABLE
IQ_PHASE_ADJ_ENABLE
FS4_MODULATION_ENABLE
NCO_SIDEBAND_SEL
Settings
0
1
0
SEND_IDATA_TO_QDAC
Description
Enable the inverse sinc filter.
Enable the NCO.
Enable digital IQ gain adjustment and dc offset.
Enable digital IQ phase adjustment.
Enable fS/4 modulation function.
Selects the single-side NCO modulation image.
The NCO outputs the high-side image.
The NCO outputs the low-side image.
Send the IDATA to the QDAC. When enabled, I data is sent
to both the IDAC and the QDAC. The Q data path still runs,
and the Q data is ignored.
INTERPOLATION CONTROL REGISTER
Address: 0x28, Reset: 0x00, Name: INTERPOLATION_CTRL
Table 54. Bit Descriptions for INTERPOLATION_CTRL
Bits
[1:0]
Bit Name
INTERPOLATION_MODE
Settings
00
10
11
Description
Interpolation rate and mode selection.
2× Mode 1; use HB1 filter.
4× mode; use HB1 and HB2 filters.
8× mode; use all three filters (HB1, HB2, and HB3).
Rev. 0 | Page 52 of 64
Data Sheet
AD9142
OVER THRESHOLD CTRL0 REGISTER
Address: 0x29, Reset: 0x00, Name: OVER_THRESHOLD_CTRL0
Table 55. Bit Descriptions for OVER_THRESHOLD_CTRL0
Bits
[7:0]
Bit Name
THRESHOLD_LEVEL_REQUEST_LSB
Settings
Description
See Register 0x2A.
Reset
0x0
Access
RW
Reset
0x00
Access
RW
Reset
0x0
0x0
0x0
Access
RW
RW
RW
Reset
0x0
Access
R
Reset
0x00
Access
R
OVER THRESHOLD CTRL1 REGISTER
Address: 0x2A, Reset: 0x00, Name: OVER_THRESHOLD_CTRL1
Table 56. Bit Descriptions for OVER_THRESHOLD_CTRL1
Bits
[4:0]
Bit Name
THRESHOLD_LEVEL_REQUEST_MSB
Settings
Description
Minimum average input power (I2 + Q2) to trigger the
input power protection function.
OVER THRESHOLD CTRL2 REGISTER
Address: 0x2B, Reset: 0x00, Name: OVER_THRESHOLD_CTRL2
Table 57. Bit Descriptions for OVER_THRESHOLD_CTRL2
Bits
7
6
[3:0]
Bit Name
ENABLE_PROTECTION
IQ_DATA_SWAP
SAMPLE_WINDOW_LENGTH
Settings
0000
0001
…
1010
1011 to
1111
Description
Enable input power protection.
Swap I and Q data in average power calculation.
Number of data input samples for power averaging.
512 IQ data sample pairs.
1024 IQ data sample pairs.
219 IQ data sample pairs.
invalid.
INPUT POWER READBACK LSB REGISTER
Address: 0x2C, Reset: 0x00, Name: INPUT_POWER_READBACK_LSB
Table 58. Bit Descriptions for INPUT_POWER_READBACK_LSB
Bits
[7:0]
Bit Name
INPUT_POWER_READBACK_LSB
Settings
Description
See Register 0x2D.
INPUT POWER READBACK MSB REGISTER
Address: 0x2D, Reset: 0x00, Name: INPUT_POWER_READBACK_MSB
Table 59. Bit Descriptions for INPUT_POWER_READBACK_MSB
Bits
[4:0]
Bit Name
INPUT_POWER_READBACK_MSB
Settings
Description
Input signal average power readback.
Rev. 0 | Page 53 of 64
AD9142
Data Sheet
NCO CONTROL REGISTER
Address: 0x30, Reset: 0x00, Name: NCO_CTRL
Table 60. Bit Descriptions for NCO_CTRL
Bits
6
5
4
1
0
Bit Name
NCO_FRAME_UPDATE_ACK
SPI_NCO_PHASE_RST_ACK
SPI_NCO_PHASE_RST_REQ
NCO_SPI_UPDATE_ACK
NCO_SPI_UPDATE_REQ
Settings
Description
Frequency tuning word update request from frame.
NCO phase SPI reset acknowledge.
NCO phase SPI reset request.
Frequency tuning word update acknowledge.
Frequency tuning word update request from SPI.
Reset
0x0
0x0
0x0
0x0
0x0
Access
R
R
RW
R
RW
Reset
0x00
Access
RW
Reset
0x00
Access
RW
Reset
0x00
Access
RW
Reset
0x10
Access
RW
Reset
0x00
Access
RW
NCO_FREQ_TUNING_WORD0 REGISTER
Address: 0x31, Reset: 0x00, Name: NCO_FREQ_TUNING_WORD0
Table 61. Bit Descriptions for NCO_FREQ_TUNING_WORD0
Bits
[7:0]
Bit Name
NCO_FTW0
Settings
Description
See Register 0x34.
NCO_FREQ_TUNING_WORD1 REGISTER
Address: 0x32, Reset: 0x00, Name: NCO_FREQ_TUNING_WORD1
Table 62. Bit Descriptions for NCO_FREQ_TUNING_WORD1
Bits
[7:0]
Bit Name
NCO_FTW1
Settings
Description
See Register 0x34.
NCO_FREQ_TUNING_WORD2 REGISTER
Address: 0x33, Reset: 0x00, Name: NCO_FREQ_TUNING_WORD2
Table 63. Bit Descriptions for NCO_FREQ_TUNING_WORD2
Bits
[7:0]
Bit Name
NCO_FTW2
Settings
Description
See Register 0x34.
NCO_FREQ_TUNING_WORD3 REGISTER
Address: 0x34, Reset: 0x10, Name: NCO_FREQ_TUNING_WORD3
Table 64. Bit Descriptions for NCO_FREQ_TUNING_WORD3
Bits
[7:0]
Bit Name
NCO_FTW3
Settings
Description
FTW[31:0] is the 32-bit frequency tuning word that determines the
frequency of the complex carrier generated by the on-chip NCO.
The frequency is not updated when the FTW registers are written. The
values are only updated when a serial port update or frame update is
initialized in Register 0x30. It is in twos complement format.
NCO_PHASE_OFFSET0 REGISTER
Address: 0x35, Reset: 0x00, Name: NCO_PHASE_OFFSET0
Table 65. Bit Descriptions for NCO_PHASE_OFFSET0
Bits
[7:0]
Bit Name
NCO_PHASE_OFFSET_LSB
Settings
Description
See Register 0x36.
Rev. 0 | Page 54 of 64
Data Sheet
AD9142
NCO_PHASE_OFFSET1 REGISTER
Address: 0x36, Reset: 0x00, Name: NCO_PHASE_OFFSET1
Table 66. Bit Descriptions for NCO_PHASE_OFFSET1
Bits
[7:0]
Bit Name
NCO_PHASE_OFFSET_MSB
Settings
Description
This register sets the initial phase of the complex carrier signal upon reset.
The phase offset spans from 0 degrees to 360 degrees. Each bit represents
an offset of 0.0055 degrees. This value is in twos complement format.
Reset
0x00
Access
RW
Reset
0x00
Access
RW
Reset
0x0
Access
RW
Reset
0x00
Access
RW
Reset
0x00
Access
RW
Reset
0x00
Access
RW
IQ_PHASE_ADJ0 REGISTER
Address: 0x37, Reset: 0x00, Name: IQ_PHASE_ADJ0
Table 67. Bit Descriptions for IQ_PHASE_ADJ0
Bits
[7:0]
Bit Name
IQ_PHASE_ADJ_LSB
Settings
Description
See Register 0x38.
IQ_PHASE_ADJ1 REGISTER
Address: 0x38, Reset: 0x000, Name: IQ_PHASE_ADJ1
Table 68. Bit Descriptions for IQ_PHASE_ADJ1
Bits
[4:0]
Bit Name
IQ_PHASE_ADJ_MSB
Settings
Description
IQ phase adjust, Bits[12:0], is used to insert a phase offset between the
I and Q datapaths. It provides an adjustment range of ±14 degrees with
a step of 0.0035 degrees. This value is in twos complement. See the
Quadrature Phase Adjustment section for more information.
IDAC_DC_OFFSET0 REGISTER
Address: 0x3B, Reset: 0x00, Name: IDAC_DC_OFFSET0
Table 69. Bit Descriptions for IDAC_DC_OFFSET0
Bits
[7:0]
Bit Name
IDAC_DC_OFFSET_LSB
Settings
Description
See Register 0x3C.
IDAC_DC_OFFSET1 REGISTER
Address: 0x3C, Reset: 0x00, Name: IDAC_DC_OFFSET1
Table 70. Bit Descriptions for IDAC_DC_OFFSET1
Bits
[7:0]
Bit Name
IDAC_DC_OFFSET_MSB
Settings
Description
IDAC DC offset, Bits[15:0], is a dc value that is added directly to the
sample values written to the IDAC.
QDAC_DC_OFFSET0 REGISTER
Address: 0x3D, Reset: 0x00, Name: QDAC_DC_OFFSET0
Table 71. Bit Descriptions for QDAC_DC_OFFSET0
Bits
[7:0]
Bit Name
QDAC_DC_OFFSET_LSB
Settings
Description
See Register 0x3E.
Rev. 0 | Page 55 of 64
AD9142
Data Sheet
QDAC_DC_OFFSET1 REGISTER
Address: 0x3E, Reset: 0x00, Name: QDAC_DC_OFFSET1
Table 72. Bit Descriptions for QDAC_DC_OFFSET1
Bits
[7:0]
Bit Name
QDAC_DC_OFFSET_MSB
Settings
Description
QDAC DC offset, Bits[15:0], is a dc value that is added directly to the
sample values written to the QDAC.
Reset
0x00
Access
RW
Reset
0x20
Access
RW
Reset
0x20
Access
RW
Reset
0x01
Access
RW
Reset
0x0
Access
RW
0x0
R
0x01
RW
IDAC_GAIN_ADJ REGISTER
Address: 0x3F, Reset: 0x20, Name: IDAC_GAIN_ADJ
Table 73. Bit Descriptions for IDAC_GAIN_ADJ
Bits
[5:0]
Bit Name
IDAC_GAIN_ADJ
Settings
Description
This register is the 6-bit digital gain adjust on the I channel. The bit
weighting is MSB = 20, LSB = 2−5, which yields a multiplier range of 0 to 2 or
−∞ to 6 dB. The default gain setting is 0x20, which maps to unity gain (0 dB).
QDAC_GAIN_ADJ REGISTER
Address: 0x40, Reset: 0x20, Name: QDAC_GAIN_ADJ
Table 74. Bit Descriptions for QDAC_GAIN_ADJ
Bits
[5:0]
Bit Name
QDAC_GAIN_ADJ
Settings
Description
This register is the 6-bit digital gain adjust on the Q channel. The bit
weighting is MSB = 20, LSB = 2−5, which yields a multiplier range of 0 to 2 or
−∞ to 6 dB. The default gain setting is 0x20, which maps to unity gain (0 dB).
GAIN STEP CONTROL0 REGISTER
Address: 0x41, Reset: 0x01, Name: GAIN_STEP_CTRL0
Table 75. Bit Descriptions for GAIN_STEP_CTRL0
Bits
[5:0]
Bit Name
RAMP_UP_STEP
Settings
Description
This register sets the step size of the increasing gain. The digital gain
increases by the configured amount in every four DAC cycles until the
gain reaches the setting in I/QDAC_GAIN_ADJ (Register 0x3F and
Register 0x40). The bit weighting is MSB = 21, LSB = 2−4. Note that the
value in this register should not be greater than the values in the
I/QDAC_GAIN_ADJ (Register 0x3F and Register 0x40).
GAIN STEP CONTROL1 REGISTER
Address: 0x42, Reset: 0x01, Name: GAIN_STEP_CTRL1
Table 76. Bit Descriptions for GAIN_STEP_CTRL1
Bits
7
Bit Name
DAC_OUTPUT_STATUS
6
DAC_OUTPUT_ON
[5:0]
RAMP_DOWN_STEP
Settings
Description
This bit indicates the DAC output on/off status. When the DAC output
is automatically turned off, this bit is 1.
In the case where the DAC output is automatically turned off in the
input power protection mode or TX enable mode, this register allows
for turning on the DAC output manually. It is a self clear bit.
This register sets the step size of the decreasing gain. The digital gain
decreases by the configured amount in every four DAC cycles until the
gain reaches zero. The bit weighting is MSB = 21, LSB = 2−4. Note that the
value in this register should not be greater than the values in the
I/QDAC_GAIN_ADJ (Register 0x3F and Register 0x40).
Rev. 0 | Page 56 of 64
Data Sheet
AD9142
TX ENABLE CONTROL REGISTER
Address: 0x43, Reset: 0x07, Name: TX_ENABLE_CTRL
Table 77. Bit Descriptions for TX_ENABLE_CTRL
Bits
2
Bit Name
TXENABLE_GAINSTEP_EN
1
TXENABLE_SLEEP_EN
0
TXENABLE_POWER_DOWN_EN
Settings
Description
DAC output gradually turns on/off under the control of the
TXENABLE signal from the TXEN pin according to the settings
in Register 0x41 and Register 0x42.
When set to 1, the device is put in sleep mode when the
TXENABLE signal from the TXEN pin is low.
When set to 1, the device is put in power down mode when
TXENABLE signal from the TXEN pin is low.
Reset
0x1
Access
RW
0x1
RW
0x1
RW
Reset
0x1
Access
RW
0x1
RW
0x1
RW
0x1
RW
Reset
0xFF
Access
RW
Reset
0x0
0x7
Access
RW
RW
DAC OUTPUT CONTROL REGISTER
Address: 0x44, Reset: 0x8F, Name: DAC_OUTPUT_CTRL
Table 78. Bit Descriptions for DAC_OUTPUT_CTRL
Bits
7
Bit Name
DAC_OUTPUT_CTRL_EN
Settings
3
FIFO_WARNING_SHUTDOWN_EN
2
OVERTHRESHOLD_SHUTDOWN_EN
0
FIFO_ERROR_SHUTDOWN_EN
Description
Enable the DAC output control. This bit needs to be set to 1 to
enable the rest of the bits in this register.
When this bit and Bit 7 are both high, if a FIFO warning occurs,
the DAC output shuts down automatically. By default, this
function is on.
The DAC output is turned off when the input average power is
greater than the predefined threshold.
The DAC output is turned off when the FIFO reports warnings.
DATA RECEIVER TEST CONTROL REGISTER
Address: 0x5E, Reset: 0xFF, Name: DATA_RX_CTRL0
Table 79. Bit Descriptions for DATA_RX_CTRL0
Bits
[7:0]
Bit Name
DLY_TAP_LSB
Settings
Description
See Register 0x5F[2:0].
DATA RECEIVER TEST CONTROL REGISTER
Address: 0x5F, Reset: 0x07, Name: DATA_RX_CTRL1
Table 80. Bit Descriptions for DATA_RX_CTRL1
Bits
3
[2:0]
Bit Name
DLYLINE_EN
DLY_TAP_MSB
Settings
00
01
10
11
Description
1 = Enable the data interface.
Four available delay settings. See the Interface Delay Line section for more
information.
0x000
0x007
0x07F
0x5FF
Rev. 0 | Page 57 of 64
AD9142
Data Sheet
DEVICE CONFIGURATION0 REGISTER
Address: 0x79, Reset: 0x00, Name: DEVICE_CONFIG0
Table 81. Bit Descriptions for DEVICE_CONFIG0
Bits
[7:0]
Bit Name
DEVICE_
CONFIGURATION0
Settings
0x18
Description
Recommended setting for device start-up configuration
Reset
0x00
Access
RW
Description
Chip version
Reset
0x05
Access
R
Reset
0x00
Access
RW
Reset
0x00
Access
RW
VERSION REGISTER
Address: 0x7F, Reset: 0x05, Name: Version
Table 82. Bit Descriptions for Version
Bits
[7:0]
Bit Name
Version
Settings
DEVICE CONFIGURATION1 REGISTER
Address: 0x80, Reset: 0x00, Name: DEVICE_CONFIG1
Table 83. Bit Descriptions for DEVICE_CONFIG1
Bits
[7:0]
Bit Name
DEVICE_
CONFIGURATION1
Settings
0xAD
Description
Recommended setting for device start-up configuration
DEVICE CONFIGURATION2 REGISTER
Address: 0xE1, Reset: 0x00, Name: DEVICE_CONFIG2
Table 84. Bit Descriptions for DEVICE_CONFIG2
Bits
[7:0]
Bit Name
DEVICE_
CONFIGURATION2
Settings
0x1A
Description
Recommended setting for device start-up configuration
Rev. 0 | Page 58 of 64
Data Sheet
AD9142
DAC LATENCY AND SYSTEM SKEWS
DACCLK/8
DIV 2
DACCLK/4
DACCLK
DIV 2
DIV 2
DACCLK/2
FIFO
RdPtr
DATA
INTERFACE
FIFO
HB2
HB1
OTHER DIGITAL
FUNCTIONALITIES
HB3
I AND
Q DAC
FIFO
WrPtr
DCI
VARYING
LATENCY
FIXED
LATENCY
VARYING
LATENCY
10930-064
FIXED
LATENCY
Figure 60. Breakdown of Pipeline Latencies
Figure 61 is an example of FIFO latency variation. The latency in
Case 2 is two data cycles longer than that in Case 1. If other
latencies are the same, the skew between the DAC outputs in
these two cases is, likewise, two data cycles. Therefore, to keep a
constant FIFO latency, the FIFO depth needs to be reset to a predefined value. Theoretically, any value other than 0 is valid but
typically it is set to 4 to maximize the capacity of absorbing the
rate fluctuation between the read and write side.
FIFO
WrPtr
DATA 1
FIFO
WrPtr
DATA 1
FIFO
RdPtr
DATA 2
FIFO LATENCY VARIATION
There are eight data slots in the FIFO. The FIFO read and write
pointers circulate the FIFO from Slot 0 to Slot 7 and back to Slot 0.
The FIFO depth is defined as the number of FIFO slots that are
required for the read pointer to catch the write pointer. It is also
the time a particular piece of data stays in the FIFO from the
point that it is written into the FIFO to the point where it is read
out from the FIFO. Therefore, the latency of the FIFO is equivalent
to its depth.
FIFO
DATA 0
DATA 2
DATA 3
DATA 3
DATA 4
DATA 4
DATA 5
DATA 5
DATA 6
DATA 6
DATA 7
DATA 7
CASE 1:
LATENCY = 4 DCI CYCLES
CASE 2:
LATENCY = 6 DCI CYCLES
FIFO
RdPtr
Figure 61. Example of FIFO Latency Difference
Figure 62 shows two equivalent cases of FIFO latency of four data
cycles. Although neither the read nor the write pointer match
each other in these two cases, the FIFO depth is the same in both
cases. Also, note that the beginning slots of the data stream in the
two cases are not the same, but the read and write pointers point
to the same piece of data in both cases. This does not affect the
alignment accuracy of the DAC outputs as long as the data and
the DCIs are well aligned at multiple devices.
FIFO
FIFO
DATA 0
DATA 5
FIFO
WrPtr
DATA 1
DATA 2
FIFO
RdPtr
DATA 3
DATA 4
FIFO
WrPtr
DATA 6
DATA 7
DATA 0
LATENCY = 4 DCI CYCLES
DATA 1
DATA 5
DATA 2
DATA 6
DATA 3
DATA 7
DATA 4
Figure 62. Example of Equal FIFO Latencies
Rev. 0 | Page 59 of 64
FIFO
RdPtr
10930-066
DACs, like any other devices with internal multiphase clocks,
have an inherent pipeline latency variation. Figure 60 shows the
breakdown of pipeline latencies in the AD9142. The highlighted
section, including the FIFO and the clock generation circuitry, is
where the pipeline latencies vary. Upon each power-on, the status
of both the FIFO and the clock generation state machine is
arbitrary. This leads to varying latency in these two blocks.
FIFO
DATA 0
10930-065
DAC LATENCY VARIATIONS
AD9142
Data Sheet
CLOCK GENERATION LATENCY VARIATION
CORRECTING SYSTEM SKEWS
The state machine of the clock generation circuitry is another
source of latency variations; this type of latency variation results
from inherent phase uncertainty of the static frequency dividers.
The divided down clock can be high or low at the rising edge of
the input clock, unless specifically forced to a known state. This
means that whenever there is interpolation (when slower clocks
need to be internally generated by dividing down the DACCLK),
there is an inherent latency variation in the DAC. Figure 63 is an
example of this latency variation in 2× interpolation. There are
two phase possibilities in the DACCLK/2 clock. The DACCLK/2
clock is used to read data from the FIFO and to drive the interpolation filter. Regardless of which clock edge is used to drive the
digital circuit, there is a latency of one DAC clock cycle between
Case 1 and Case 2 (see Figure 62). Because the power-on state
arbitrarily falls in one of the two cases, the phase uncertainty of
the divider appears as a varying skew between two DAC outputs.
Generally, it is assumed that the input data and the DCI among
multiple devices are well aligned to each other. Depending on the
system design, the data and DCI being input into each DAC can
originate from various FPGAs or ASICs. Without synchronizing
the data sources, the output of one data source can be skewed
from that of another. The alignment between multiple data
sources can also drift over temperature.
HB1
HB2
HB3
Figure 64 shows an example of a 2-channel transmitter with two
data sources and two dual DACs. A constant but unknown phase
offset appears between the outputs of the DAC devices, even if
the DAC does not introduce any latency variations. The
multidevice synchronization in the AD9142 can be used to
compensate the skew due to misalignment of the data sources by
resetting the two sides of the FIFO independently through two
external reference clocks: the frame and the sync clock. The offset
between the two data sources is then absorbed by the FIFO and
clock generation block in the DAC. For more information about
using the multidevice synchronization function, refer to the
Synchronization Implementation section.
DCI
FRAME
DAC
16-BIT DATA
DATA
GEN
MATCH SYNC LINE FOR ALL DATA GEN
DACCLK
DACCLK/2
(CASE 1)
10930-067
DACCLK/2
(CASE 2)
LATENCY VARIATION = 1 DACCLK CYCLE
Figure 63. Latency Variation in 2× Interpolation from Clock Generation
DCI
FRAME
DAC
16-BIT DATA
DCI
FRAME
DAC
16-BIT DATA
DATA
GEN
DCI
FRAME
DAC
16-BIT DATA
2
SYNC CLOCK
DATA SKEW
Figure 64. DAC Output Skew from Skewed Input Data and DCI
Rev. 0 | Page 60 of 64
10930-068
4
MASTER
REF CLOCK
Data Sheet
AD9142
PACKAGING AND ORDERING INFORMATION
OUTLINE DIMENSIONS
10.10
10.00 SQ
9.90
0.60
0.42
0.24
0.60
0.42
0.24
0.30
0.23
0.18
55
54
72
1
PIN 1
INDICATOR
PIN 1
INDICATOR
9.85
9.75 SQ
9.65
0.50
BSC
0.50
0.40
0.30
18
37
BOTTOM VIEW
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
0.25 MIN
8.50 REF
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-VNND-4
06-25-2012-A
1.00
0.85
0.80
19
36
TOP VIEW
12° MAX
6.15
6.00 SQ
5.85
EXPOSED
PAD
Figure 65. 72-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
10 mm × 10 mm Body, Very Thin Quad
(CP-72-7)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
AD9142BCPZ
AD9142BCPZRL
AD9142-M5372-EBZ
AD9142-M5375-EBZ
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
72-lead LFCSP_VQ
72-lead LFCSP_VQ
Evaluation Board Connected to ADL5372 Modulator
Evaluation Board Connected to ADL5375 Modulator
Z = RoHS Compliant Part.
Rev. 0 | Page 61 of 64
Package Option
CP-72-7
CP-72-7
AD9142
Data Sheet
NOTES
Rev. 0 | Page 62 of 64
Data Sheet
AD9142
NOTES
Rev. 0 | Page 63 of 64
AD9142
Data Sheet
NOTES
©2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D10930-0-11/12(0)
Rev. 0 | Page 64 of 64
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Analog Devices Inc.:
AD9142BCPZ AD9142BCPZRL
Similar pages