Renesas HA1631S01 Single cmos comparator (push pull/open drain output) Datasheet

HA1631S01/02/03/04 Series
Single CMOS Comparator (Push Pull/Open Drain Output)
REJ03D0056-0200
Rev.2.00
Mar 10, 2006
Description
The HA1631S01/02/03/04 are low power single CMOS Comparator featuring low voltage operation with typical current
supply of 5 µA/50 µA. They are designed to operate from a single power supply. HA1631S01/02 have push-pull full
swing outputs that allow direct connections to logic devices. The Open Drain version HA1631S03/04 enable Output
Level shifting through external pull up resistors. Available in an ultra-small CMPAK-5 package, they occupy only 1/8
the area of the SOP-8 package.
Features
• Low supply current
HA1631S01/03
: IDDtyp = 5 µA (VDD = 3.0 V)
HA1631S02/04
: IDDtyp = 50 µA (VDD = 3.0 V)
• Low voltage operation : VDD = 1.8 to 5.5 V
• Low input offset voltage : VIOmax = 5 mV
• Low input bias current : IIBtyp = 1 pA
• Maximum output voltage : VOHmin = 2.9 V (at VDD = 3.0 V)
• Input common voltage range includes ground
• On-chip ESD protection
• Available in CMPAK-5 and MPAK-5 package using Pb free lead frame
Ordering Information
Type No.
HA1631S01CM
HA1631S02CM
HA1631S03CM
HA1631S04CM
HA1631S01LP
HA1631S02LP
HA1631S03LP
HA1631S04LP
Rev.2.00 Mar 10, 2006 page 1 of 22
Package Name
CMPAK-5
Package Code
PTSP0005ZC-A
MPAK-5
PLSP0005ZB-A
HA1631S01/02/03/04 Series
Pin Arrangement
VDD
VOUT
5
4
+ –
1
2
3
VIN(+) VSS VIN(–)
Equivalent Circuit
VDD
*
IN–
IN+
VSS
* Not available in Open Drain version (HA1631S03/04)
Rev.2.00 Mar 10, 2006 page 2 of 22
OUTPUT
HA1631S01/02/03/04 Series
Absolute Maximum Ratings
(Ta = 25°C)
Item
Symbol
Ratings
Unit
Remarks
Supply voltage
VDD
7.0
V
Differential input voltage
VIN(diff)
–VDD to +VDD
V
Note 1
Input voltage
VIN
0.1 to +VDD
V
Output current
IOUT
28
mA
Note 2
Power dissipation
PT
80/120
mW
CMPAK-5/MPAK-5
Operating temperature
Topr
–40 to +85
°C
Storage temperature
Tstg
–55 to +125
°C
Notes: 1. Do not apply input voltage exceeding VDD or 7 V.
2. The maximum output current is the maximum allowable value for continuous operation.
Electrical Characteristics
(Ta = 25°C, VDD = 3.0 V, VSS = 0 V)
Item
Input offset voltage
Input bias current
Symbol
VIO
IIB
Min
—
—
Typ
—
(1)
Max
5
100
Unit
mV
pA
Test Conditions
VIN = VDD/2, RL = 1MΩ
VIN = VDD/2
Input offset current
Common mode input voltage range
Supply current
HA1631S01/03
HA1631S02/04
Response time
HA1631S01
HA1631S01/03
HA1631S01
HA1631S01/03
HA1631S02
HA1631S02/04
HA1631S02
HA1631S02/04
IIO
VCM
IDD
—
–0.1
—
—
—
—
—
—
—
—
—
—
6
(1)
—
5
50
(1.20)
(0.55)
(24)
(7)
(0.33)
(0.17)
(12)
(7)
13
100
2.1
10
100
—
—
—
—
—
—
—
—
—
pA
V
µA
µA
µs
µs
ns
ns
µs
µs
ns
ns
mA
VIN = VDD/2
7
60
14
80
—
—
mA
dB
Vout = 0.5V
VIN1 = 0V, VIN2 = 2V
50
60
VDD–0.1
—
—
70
80
—
—
(0.1)
—
—
—
0.1
—
dB
dB
V
V
nA
VDD1 = 1.8V, VDD2 = 5.5V
RL = 10kΩ to VSS
RL = 10kΩ to VDD
1.8
—
5.5
V
TPLH
TPHL
tr
tf
TPLH
TPHL
tr
tf
Output source current
(HA1631S01/02)
Output sink current
HA1631S01/03
Common mode
rejection ratio
HA1631S02/04
IOSOURCE
Power supply rejection ratio
Output voltage high
Output voltage low
PSRR
VOH
VOL
Output leakage current
(Only for HA1631S03/04)
Operating voltage range
Note: ( ): Design specification
ILO
Rev.2.00 Mar 10, 2006 page 3 of 22
IOSINK
CMRR
Vopr
VDD = 3V, VIN+ = 1V,
VIN– = 0V
1V DC bias,
100mV overdrive,
CL = 15pF
Vout = 2.5V
VIN+ = 1V, VIN– = 0V,
VO = 3V
HA1631S01/02/03/04 Series
Table of Graphs
Electrical Characteristics
Supply current
IDD
vs. Supply voltage(Out H)
HA1631S01
Figure
HA1631S02
Figure
HA1631S03
Figure
HA1631S04
Figure
Test
Circuit No.
1-1
2-1
3-1
4-1
1
vs. Supply voltage(Out L)
1-2
2-2
3-2
4-2
2
vs. Temperature(Out H)
1-3
2-3
3-3
4-3
1
Output high voltage
VOH
vs. Rload
1-18
2-18
3-4
4-4
4
Output source
current
IOSOURCE
vs. Output high voltage
1-4
2-4
—
—
5
Output low voltage
VOL
vs. Rload
1-17
2-17
3-14
4-14
6
Output sink current
IOSINK
vs. Output low voltage
1-5
2-5
3-4
4-4
5
Input offset voltage
VIO
vs. Supply voltage
1-6
2-6
3-5
4-5
8
vs. Temperature
1-7
2-7
3-6
4-6
7
Common mode input
voltage range
VCM
vs. Temperature
1-8
2-8
3-7
4-7
9
Power supply
rejection ratio
PSRR
vs. Supply voltage
1-9
2-9
3-8
4-8
11
Common mode
rejection ratio
CMRR
vs. Input voltage
1-10
2-10
3-9
4-9
12
Input bias current
IIB
vs. Temperature
1-11
2-11
3-10
4-10
10
vs. Input voltage
1-12
2-12
3-11
4-11
10
Falling time
Rising time
Propagation delay
time
tf
tr
vs. Temperature
1-13
2-13
3-12
4-12
13
vs. Cload
1-15
2-15
3-13
4-13
13
Time waveform
1-20
2-20
3-15
4-15
13
vs. Temperature
1-14
2-14
—
—
13
vs. Cload
1-16
2-16
—
—
13
Time waveform
1-19
2-19
—
—
13
TPLH
Time waveform
1-21
2-21
—
—
13
TPHL
Time waveform
1-22
2-22
3-16, 3-17
4-16, 4-17
13
Rev.2.00 Mar 10, 2006 page 4 of 22
HA1631S01/02/03/04 Series
Main Characteristics
Figure 1-1 HA1631S01
Supply Current vs. Supply Voltage
(Output High)
7.0
Ta = 25°C
VIN+ = 1.0V
VIN– = 0.0V
6.0
5.0
Supply Current IDD (µA)
Supply Current IDD (µA)
7.0
4.0
3.0
2.0
1.0
0.0
0
1
2
3
4
Figure 1-2 HA1631S01
Supply Current vs. Supply Voltage
(Output Low)
5
Ta = 25°C
6.0 VIN+ = 0.0V
4.0
3.0
2.0
1.0
0.0
6
VIN– = 1.0V
5.0
0
1
7.5
5.0
2.5
3.5
–25
0
25
50
75
100
1.5
1.0
0.5
10
20
30
Output Sink Current IOSINK (mA)
Rev.2.00 Mar 10, 2006 page 5 of 22
6
Figure 1-4 HA1631S01
Output High Voltage vs. Output Source Current
3.5
3.0
2.5
2.0
1.5
1.0
0.5 Ta = 25°C
VDD = 3.0V
0.0
0
10
30
20
40
Figure 1-6 HA1631S01
Input Offset Voltage vs. Supply Voltage
2.0
0
5
Figure 1-5 HA1631S01
Output Low Voltage vs. Output Sink Current
2.5
0.0
4
Output Source Current IOSOURCE (mA)
Ta = 25°C
VDD = 3.0V
3.0
3
Ambient Temperature Ta (°C)
40
Input Offset Voltage VIO (mV)
Supply Current IDD (µA)
VDD = 5.0V
VDD = 3.0V
VDD = 1.8V
0.0
–50
Output Low Voltage VOL (V)
Output High Voltage VOH (V)
Figure 1-3 HA1631S01
Supply Current vs. Ambient Temperature
10.0
2
Supply Voltage VDD (V)
Supply Voltage VDD (V)
4
Ta = 25°C
3 VIN = VDD/2
2
1
0
–1
–2
–3
–4
0
1
2
3
4
Supply Voltage VDD (V)
5
6
VDD = 1.8V, VIN = 0.9V
VDD = 3.0V, VIN = 1.5V
VDD = 5.0V, VIN = 2.5V
3
2
1
0
–1
–2
–3
–4
–50
–25
0
25
50
75
100
VCM+
1.5
Common Mode
Input Voltage Range
1.0
0.5
VCM–
0.0
–0.5
VDD = 3.0V
–1.0
–50
–25
0
25
50
75
100
Figure 1-9 HA1631S01
Power Supply Rejection Ratio vs. Supply Voltage
Figure 1-10 HA1631S01
Common Mode Rejection Ratio vs. Input Voltage
80
60
Ta = 25°C
VIN = 0.0V
VDD = 0.0 to 2.75V
VSS = 0.0 to –2.75V
VDD & VSS
Simultaneous Sweep
40
20
1
2
3
4
5
6
7
Supply Voltage VDD to VSS (V)
Figure 1-11 HA1631S01
Input Bias Current vs. Ambient Temperature
Input Bias Current IIB (pA)
Input Bias Current IIB (pA)
2.0
Ambient Temperature Ta (°C)
100
200
Figure 1-8 HA1631S01
Common Mode Input Voltage vs. Ambient Temperature
2.5
Ambient Temperature Ta (°C)
120
0
Common Mode Input Voltage VCM (V)
4
Figure 1-7 HA1631S01
Input Offset Voltage vs. Ambient Temperature
Common Mode Rejection Ratio CMRR (dB)
Power Supply Rejection Ratio PSRR (dB)
Input Offset Voltage VIO (mV)
HA1631S01/02/03/04 Series
VDD = 3.0V
100
0
100
80
60
40
Ta = 25°C
20 VDD = 1.5V
VSS = –1.5V
0
–2.0
–1.5
–1.0
–0.5
0.0
0.5
1.0
Input Voltage VIN (V)
Figure 1-12 HA1631S01
Input Bias Current vs. Input Voltage
200
Ta = 25°C
VDD = 3.0V
100
0
–100
–100
–200
–50
120
–25
0
25
50
75
Ambient Temperature Ta (°C)
Rev.2.00 Mar 10, 2006 page 6 of 22
100
–200
0.0
0.5
1.0
1.5
2.0
Input Voltage VIN (V)
2.5
3.0
HA1631S01/02/03/04 Series
Figure 1-13 HA1631S01
Falling Time vs. Ambient Temperature
18
70
VDD = 1.8V
14
12
Rising Time tr (ns)
Falling Time tf (ns)
16
VDD = 5.5V
10
8
6
VDD = 3.0V
4
2
0
–50
25
50
75
80
20
VDD = 3.0V
10
140
–25
0
25
50
75
10
20
30
40
120 VDD = 2.0V
VSS = –1.0V
100 VIN+ = ±0.1Vp-p
60
40
20
0
50
Overdrive
80
0
10
20
30
40
Capacitor Load CL (pF)
Capacitor Load CL (pF)
Figure 1-17 HA1631S01
Output Low Voltage vs. Resistor Load
Figure 1-18 HA1631S01
Output High Voltage vs. Resistor Load
Ta = 25°C
VDD = 3.0V
1.5
1.0
0.5
100
100
Ta = 25°C
2.0
0.0
10
30
Figure 1-16 HA1631S01
Rising Time vs. Capacitor Load
20
2.5
VDD = 1.8V
Figure 1-15 HA1631S01
Falling Time vs. Capacitor Load
40
3.0
40
Ambient Temperature Ta (°C)
60
0
VDD = 5.5V
50
Ambient Temperature Ta (°C)
Rising Time tr (ns)
100
60
0
–50
100
Ta = 25°C
VDD = 2.0V
VSS = –1.0V
VIN+ = ±0.1Vp-p
Overdrive
120
0
Output Low Voltage VOL (V)
0
Output High Voltage VOH (V)
Falling Time tf (ns)
140
–25
Figure 1-14 HA1631S01
Rising Time vs. Ambient Temperature
1k
10k
100k
Resistor Load RL (Ω)
Rev.2.00 Mar 10, 2006 page 7 of 22
1M
3.0
50
2.5
2.0
1.5
1.0
0.5 Ta = 25°C
VDD = 3.0V
0.0
10
100
1k
10k
100k
Resistor Load RL (Ω)
1M
HA1631S01/02/03/04 Series
Figure 1-20 HA1631S01
Falling Time, tf
(Overdrive = ±0.1Vp-p)
Figure 1-19 HA1631S01
Rising Time, tr
(Overdrive = ±0.1Vp-p)
VDD
Ta = 25°C
VDD = 3.0V
CL = 15pF
VIN+ = ±0.1Vp-p
Overdrive
VDD
GND
GND
Figure 1-21 HA1631S01
TPLH Transient Response
(Overdrive = ±0.1Vp-p)
Figure 1-22 HA1631S01
TPHL Transient Response
(Overdrive = ±0.1Vp-p)
Input Voltage
CH1
GND
CH2
GND
Ta = 25°C
VDD = 3.0V
CL = 15pF
VIN+ = ±0.1Vp-p
Overdrive
Input Voltage
CH1
GND
Ta = 25°C
VDD = 3.0V
CL = 15pF
VIN+ = ±0.1Vp-p
Overdrive
Output Voltage
Rev.2.00 Mar 10, 2006 page 8 of 22
Output Voltage
CH2
GND
Ta = 25°C
VDD = 3.0V
CL = 15pF
VIN+ = ±0.1Vp-p
Overdrive
HA1631S01/02/03/04 Series
Figure 2-1 HA1631S02
Supply Current vs. Supply Voltage
(Output High)
70
Ta = 25°C
VIN+ = 1.0V
VIN– = 0.0V
60
50
Supply Current IDD (µA)
Supply Current IDD (µA)
70
40
30
20
10
0
0
1
2
3
4
Figure 2-2 HA1631S02
Supply Current vs. Supply Voltage
(Output Low)
5
Ta = 25°C
60 VIN+ = 0.0V
40
30
20
10
0
6
VIN– = 1.0V
50
0
Supply Voltage VDD (V)
25
0
–50
Output Low Voltage VOL (V)
Output High Voltage VOH (V)
50
3.5
–25
0
25
50
75
100
1.5
1.0
0.5
10
20
30
Output Sink Current IOSINK (mA)
Rev.2.00 Mar 10, 2006 page 9 of 22
6
Figure 2-4 HA1631S02
Output High Voltage vs. Output Source Current
3.5
3.0
2.5
2.0
1.5
1.0
0.5 Ta = 25°C
VDD = 3.0V
0.0
0
10
20
30
40
Figure 2-6 HA1631S02
Input Offset Voltage vs. Supply Voltage
2.0
0
5
Figure 2-5 HA1631S02
Output Low Voltage vs. Output Sink Current
2.5
0.0
4
Output Source Current IOSOURCE (mA)
Ta = 25°C
VDD = 3.0V
3.0
3
Ambient Temperature Ta (°C)
40
Input Offset Voltage VIO (mV)
Supply Current IDD (µA)
VDD = 5.0V
VDD = 3.0V
VDD = 1.8V
75
2
Supply Voltage VDD (V)
Figure 2-3 HA1631S02
Supply Current vs. Ambient Temperature
100
1
4
Ta = 25°C
3 VIN = VDD/2
2
1
0
–1
–2
–3
–4
1
2
3
4
Supply Voltage VDD (V)
5
6
4
Figure 2-7 HA1631S02
Input Offset Voltage vs. Ambient Temperature
3
VDD = 1.8V, VIN = 0.9V
VDD = 3.0V, VIN = 1.5V
VDD = 5.0V, VIN = 2.5V
2
1
0
–1
–2
–3
–4
–50
–25
0
25
50
75
100
Common Mode Input Voltage VCM (V)
Input Offset Voltage VIO (mV)
HA1631S01/02/03/04 Series
Figure 2-8 HA1631S02
Common Mode Input Voltage vs. Ambient Temperature
2.5
2.0
VCM+
1.5
Common Mode
Input Voltage Range
1.0
0.5
VCM–
0.0
–0.5
VDD = 3.0V
–1.0
–50
Figure 2-9 HA1631S02
Power Supply Rejection Ratio vs. Supply Voltage
120
100
80
60
Ta = 25°C
VIN = 0.0V
VDD = 0.0 to 2.75V
VSS = 0.0 to –2.75V
VDD & VSS
Simultaneous Sweep
40
20
0
1
2
3
4
5
6
7
Figure 2-11 HA1631S02
Input Bias Current vs. Ambient Temperature
Input Bias Current IIB (pA)
Input Bias Current IIB (pA)
Supply Voltage VDD to VSS (V)
200
VDD = 3.0V
100
0
0
25
50
75
100
120
Figure 2-10 HA1631S02
Common Mode Rejection Ratio vs. Input Voltage
100
80
60
40
Ta = 25°C
20 VDD = 1.5V
VSS = –1.5V
0
–2.0
–1.5
–1.0
–0.5
0.0
0.5
1.0
Input Voltage VIN (V)
Figure 2-12 HA1631S02
Input Bias Current vs. Input Voltage
200
Ta = 25°C
VDD = 3.0V
100
0
–100
–100
–200
–50
–25
Ambient Temperature Ta (°C)
Common Mode Rejection Ratio CMRR (dB)
Power Supply Rejection Ratio PSRR (dB)
Ambient Temperature Ta (°C)
–25
0
25
50
75
Ambient Temperature Ta (°C)
Rev.2.00 Mar 10, 2006 page 10 of 22
100
–200
0.0
0.5
1.0
1.5
2.0
Input Voltage VIN (V)
2.5
3.0
–25
0
25
50
75
100
80
120
0
25
50
75
10
20
30
40
100 VDD = 2.0V
80
60
40
20
0
50
VSS = –1.0V
VIN+ = ±0.1Vp-p
Overdrive
0
10
20
30
40
Capacitor Load CL (pF)
Capacitor Load CL (pF)
Figure 2-17 HA1631S02
Output Low Voltage vs. Resistor Load
Figure 2-18 HA1631S02
Output High Voltage vs. Resistor Load
Ta = 25°C
VDD = 3.0V
1.5
1.0
0.5
100
100
Ta = 25°C
2.0
0.0
10
–25
Figure 2-16 HA1631S02
Rising Time vs. Capacitor Load
20
2.5
VDD = 3.0V
VDD = 1.8V
Figure 2-15 HA1631S02
Falling Time vs. Capacitor Load
40
3.0
VDD = 5.5V
Ambient Temperature Ta (°C)
60
0
20
18
16
14
12
10
8
6
4
2
0
–50
Figure 2-14 HA1631S02
Rising Time vs. Ambient Temperature
Ambient Temperature Ta (°C)
Ta = 25°C
VDD = 2.0V
VSS = –1.0V
VIN+ = ±0.1Vp-p
Overdrive
100
0
Output Low Voltage VOL (V)
VDD = 3.0V
VDD = 5.5V
Rising Time tr (ns)
Falling Time tf (ns)
120
VDD = 1.8V
Rising Time tr (ns)
20
18
16
14
12
10
8
6
4
2
0
–50
Figure 2-13 HA1631S02
Falling Time vs. Ambient Temperature
Output High Voltage VOH (V)
Falling Time tf (ns)
HA1631S01/02/03/04 Series
1k
10k
100k
Resistor Load RL (Ω)
Rev.2.00 Mar 10, 2006 page 11 of 22
1M
3.0
50
2.5
2.0
1.5
1.0
0.5 Ta = 25°C
VDD = 3.0V
0.0
10
100
1k
10k
100k
Resistor Load RL (Ω)
1M
HA1631S01/02/03/04 Series
Figure 2-19 HA1631S02
Rising Time, tr
(Overdrive = ±0.1Vp-p)
VDD
Ta = 25°C
VDD = 3.0V
CL = 15pF
VIN+ = ±0.1Vp-p
Overdrive
GND
Figure 2-20 HA1631S02
Falling Time, tf
(Overdrive = ±0.1Vp-p)
VDD
GND
Figure 2-21 HA1631S02
TPLH Transient Response
(Overdrive = ±0.1Vp-p)
Figure 2-22 HA1631S02
TPHL Transient Response
(Overdrive = ±0.1Vp-p)
Input Voltage
CH1
GND
CH2
GND
Ta = 25°C
VDD = 3.0V
CL = 15pF
VIN+ = ±0.1Vp-p
Overdrive
Input Voltage
CH1
GND
Ta = 25°C
VDD = 3.0V
CL = 15pF
VIN+ = ±0.1Vp-p
Overdrive
Output Voltage
Rev.2.00 Mar 10, 2006 page 12 of 22
Output Voltage
CH2
GND
Ta = 25°C
VDD = 3.0V
CL = 15pF
VIN+ = ±0.1Vp-p
Overdrive
HA1631S01/02/03/04 Series
Figure 3-1 HA1631S03
Supply Current vs. Supply Voltage
(Output High)
5.0
4.0
3.0
2.0
1.0
1
2
3
4
5
–25
0
25
50
75
100
1.0
0
1
2
3
4
5
6
3.5
Ta = 25°C
3.0 VDD = 3.0V
2.5
2.0
1.5
1.0
0.5
0.0
0
10
20
30
40
Ambient Temperature Ta (°C)
Output Sink Current IOSINK (mA)
Figure 3-5 HA1631S03
Input Offset Voltage vs. Supply Voltage
Figure 3-6 HA1631S03
Input Offset Voltage vs. Ambient Temperature
Ta = 25°C
VIN = VDD/2
2
1
0
–1
–2
–3
0
2.0
Figure 3-4 HA1631S03
Output Low Voltage vs. Output Sink Current
2.5
–4
3.0
Figure 3-3 HA1631S03
Supply Current vs. Ambient Temperature
5.0
3
4.0
Supply Voltage VDD (V)
7.5
4
VIN– = 1.0V
5.0
Supply Voltage VDD (V)
VDD = 5.0V
VDD = 3.0V
VDD = 1.8V
0.0
–50
Ta = 25°C
6.0 VIN+ = 0.0V
0.0
6
Output Low Voltage VOL (V)
0
10.0
Supply Current IDD (µA)
Supply Current IDD (µA)
6.0
0.0
Input Offset Voltage VIO (mV)
7.0
Ta = 25°C
VIN+ = 1.0V
VIN– = 0.0V
Input Offset Voltage VIO (mV)
Supply Current IDD (µA)
7.0
Figure 3-2 HA1631S03
Supply Current vs. Supply Voltage
(Output Low)
1
2
3
4
Supply Voltage VDD (V)
Rev.2.00 Mar 10, 2006 page 13 of 22
5
6
4
3
VDD = 1.8V, VIN = 0.9V
VDD = 3.0V, VIN = 1.5V
VDD = 5.0V, VIN = 2.5V
2
1
0
–1
–2
–3
–4
–50
–25
0
25
50
75
Ambient Temperature Ta (°C)
100
2.0
VCM+
1.5
Common Mode
Input Voltage Range
1.0
0.5
0.0
VCM–
–0.5
VDD = 3.0V
–1.0
–50
0
25
50
75
100
120
Figure 3-8 HA1631S03
Power Supply Rejection Ratio vs. Supply Voltage
100
80
60
Ta = 25°C
V = 0.0V
40 VIN = 0.0 to 2.75V
DD
VSS = 0.0 to –2.75V
20 VDD & VSS
Simultaneous Sweep
0
1
2
3
4
5
6
7
Ambient Temperature Ta (°C)
Supply Voltage VDD to VSS (V)
Figure 3-9 HA1631S03
Common Mode Rejection Ratio vs. Input Voltage
Figure 3-10 HA1631S03
Input Bias Current vs. Ambient Temperature
Input Bias Current IIB (pA)
120
–25
Power Supply Rejection Ratio PSRR (dB)
Figure 3-7 HA1631S03
Common Mode Input Voltage vs. Ambient Temperature
2.5
100
80
60
40
VSS = –1.5V
0
–2.0
200
–1.5
–1.0
–0.5
0.0
0.5
1.0
VDD = 3.0V
100
0
–200
–50
–25
0
25
50
75
Input Voltage VIN (V)
Ambient Temperature Ta (°C)
Figure 3-11 HA1631S03
Input Bias Current vs. Input Voltage
Figure 3-12 HA1631S03
Falling Time vs. Ambient Temperature
14
Ta = 25°C
VDD = 3.0V
100
0
–100
–200
0.0
200
–100
Ta = 25°C
20 VDD = 1.5V
Falling Time tf (ns)
Input Bias Current IIB (pA)
Common Mode Rejection Ratio CMRR (dB)
Common Mode Input Voltage VCM (V)
HA1631S01/02/03/04 Series
0.5
1.0
1.5
2.0
Input Voltage VIN (V)
Rev.2.00 Mar 10, 2006 page 14 of 22
2.5
3.0
12
100
VDD = 1.8V
10
8
6
VDD = 3.0V
4
VDD = 5.5V
2
0
–50
–25
0
25
50
75
Ambient Temperature Ta (°C)
100
HA1631S01/02/03/04 Series
45
Ta = 25°C
VDD = 2.0V
VSS = –1.0V
VIN+ = ±0.1Vp-p
Overdrive
40
Falling Time tf (ns)
Output Low Voltage VOL (V)
Figure 3-13 HA1631S03
Falling Time vs. Capacitor Load
35
30
25
20
15
15
10
5
0
0
10
20
30
40
50
3.0
Figure 3-14 HA1631S03
Output Low Voltage vs. Resistor Load
Ta = 25°C
2.5 VDD = 3.0V
2.0
1.5
1.0
0.5
0.0
10
Capacitor Load CL (pF)
100
1k
Figure 3-16 HA1631S03
TPHL Transient Response
(Overdrive = ±0.1Vp-p)
VDD
Input Voltage
CH1
GND
Output Voltage
GND
Figure 3-17 HA1631S03
TPHL Transient Response
(Overdrive = ±0.1Vp-p)
Input Voltage
CH1
GND
Output Voltage
CH2
GND
Ta = 25°C
VDD = 3.0V
CL = 15pF
VIN+ = ±0.1Vp-p
Overdrive
Rev.2.00 Mar 10, 2006 page 15 of 22
100k
Resistor Load RL (Ω)
Figure 3-15 HA1631S03
Falling Time, tf
Ta = 25°C
VDD = 3.0V
CL = 15pF
VIN+ = ±0.1Vp-p
Overdrive
10k
CH2
GND
Ta = 25°C
VDD = 3.0V
CL = 15pF
VIN+ = ±0.1Vp-p
Overdrive
1M
HA1631S01/02/03/04 Series
Figure 4-1 HA1631S04
Supply Current vs. Supply Voltage
(Output High)
50
40
30
20
10
1
2
3
4
5
–25
0
25
50
75
100
10
0
1
2
3
4
5
6
3.5
Ta = 25°C
3.0 VDD = 3.0V
2.5
2.0
1.5
1.0
0.5
0.0
0
10
20
30
40
Ambient Temperature Ta (°C)
Output Sink Current IOSINK (mA)
Figure 4-5 HA1631S04
Input Offset Voltage vs. Supply Voltage
Figure 4-6 HA1631S04
Input Offset Voltage vs. Ambient Temperature
Ta = 25°C
VIN = VDD/2
2
1
0
–1
–2
–3
0
20
Figure 4-4 HA1631S04
Output Low Voltage vs. Output Sink Current
25
–4
30
Figure 4-3 HA1631S04
Supply Current vs. Ambient Temperature
50
3
40
Supply Voltage VDD (V)
75
4
VIN– = 1.0V
50
Supply Voltage VDD (V)
VDD = 5.0V
VDD = 3.0V
VDD = 1.8V
0
–50
Ta = 25°C
60 VIN+ = 0.0V
0
6
Output Low Voltage VOL (V)
0
100
Supply Current IDD (µA)
Supply Current IDD (µA)
60
0
Input Offset Voltage VIO (mV)
70
Ta = 25°C
VIN+ = 1.0V
VIN– = 0.0V
Input Offset Voltage VIO (mV)
Supply Current IDD (µA)
70
Figure 4-2 HA1631S04
Supply Current vs. Supply Voltage
(Output Low)
1
2
3
4
Supply Voltage VDD (V)
Rev.2.00 Mar 10, 2006 page 16 of 22
5
6
4
3
2
1
VDD = 1.8V, VIN = 0.9V
VDD = 3.0V, VIN = 1.5V
VDD = 5.0V, VIN = 2.5V
0
–1
–2
–3
–4
–50
–25
0
25
50
75
Ambient Temperature Ta (°C)
100
VDD = 3.0V
2.5
VCM+
2.0
1.5
Common Mode
Input Voltage Range
1.0
0.5
VCM–
0.0
–0.5
–50
0
25
50
75
100
120
Figure 4-8 HA1631S04
Power Supply Rejection Ratio vs. Supply Voltage
100
80
60
Ta = 25°C
V = 0.0V
40 VIN = 0.0 to 2.75V
DD
VSS = 0.0 to –2.75V
20 VDD & VSS
Simultaneous Sweep
0
1
2
3
4
5
6
7
Ambient Temperature Ta (°C)
Supply Voltage VDD to VSS (V)
Figure 4-9 HA1631S04
Common Mode Rejection Ratio vs. Input Voltage
Figure 4-10 HA1631S04
Input Bias Current vs. Ambient Temperature
Input Bias Current IIB (pA)
120
–25
Power Supply Rejection Ratio PSRR (dB)
Figure 4-7 HA1631S04
Common Mode Input Voltage vs. Ambient Temperature
3.0
100
80
60
40
VSS = –1.5V
0
–2.0
200
–1.5
–1.0
–0.5
0.0
0.5
1.0
VDD = 3.0V
100
0
–200
–50
–25
0
25
50
75
Input Voltage VIN (V)
Ambient Temperature Ta (°C)
Figure 4-11 HA1631S04
Input Bias Current vs. Input Voltage
Figure 4-12 HA1631S04
Falling Time vs. Ambient Temperature
7.0
Ta = 25°C
VDD = 3.0V
100
0
–100
–200
0.0
200
–100
Ta = 25°C
20 VDD = 1.5V
Falling Time tf (ns)
Input Bias Current IIB (pA)
Common Mode Rejection Ratio CMRR (dB)
Common Mode Input Voltage VCM (V)
HA1631S01/02/03/04 Series
0.5
1.0
1.5
2.0
Input Voltage VIN (V)
Rev.2.00 Mar 10, 2006 page 17 of 22
2.5
3.0
6.0
100
VDD = 1.8V
5.0
4.0
3.0
VDD = 5.5V
2.0
VDD = 3.0V
1.0
0.0
–50
–25
0
25
50
75
Ambient Temperature Ta (°C)
100
HA1631S01/02/03/04 Series
Falling Time tf (ns)
120
Output Low Voltage VOL (V)
Figure 4-13 HA1631S04
Falling Time vs. Capacitor Load
Ta = 25°C
VDD = 2.0V
VSS = –1.0V
VIN+ = ±0.1Vp-p
Overdrive
100
80
60
40
20
0
0
10
20
30
40
50
3.0
Figure 4-14 HA1631S04
Output Low Voltage vs. Resistor Load
Ta = 25°C
2.5 VDD = 3.0V
2.0
1.5
1.0
0.5
0.0
10
Capacitor Load CL (pF)
100
1k
Figure 4-16 HA1631S04
TPHL Transient Response
(Overdrive = ±0.1Vp-p)
VDD
Input Voltage
CH1
GND
Output Voltage
GND
Figure 4-17 HA1631S04
TPHL Transient Response
(Overdrive = ±0.1Vp-p)
Input Voltage
CH1
GND
Output Voltage
CH2
GND
Ta = 25°C
VDD = 3.0V
CL = 15pF
RL = 10kΩ
VIN+ = ±0.1Vp-p
Overdrive
Rev.2.00 Mar 10, 2006 page 18 of 22
100k
Resistor Load RL (Ω)
Figure 4-15 HA1631S04
Falling Time, tf
(Overdrive = ±0.1Vp-p)
Ta = 25°C
VDD = 3.0V
CL = 15pF
RL = 10kΩ
VIN+ = ±0.1Vp-p
Overdrive
10k
CH2
GND
Ta = 25°C
VDD = 3.0V
CL = 15pF
RL = 10kΩ
VIN+ = ±0.1Vp-p
Overdrive
1M
HA1631S01/02/03/04 Series
Test Circuits
1. Supply Current, IDD (Output High)
2. Supply Current, IDD (Output Low)
A
A
−
+
+
−
VDD
1V
VDD
1V
3. Output Source Current, IOSOURCE
−
+
4. Output Voltage High, VOH
−
+
3V
1V
3V
1V
VOUT
RLOAD
5. Output Sink Current, IOSINK
6. Output Voltage Low, VOL
+
−
+
−
3V
1V
VIN
1kΩ
8. Input Offset Voltage vs. VDD
Only for
Open Drain
1MΩ
1MΩ
10kΩ
−
+
VOUT
1kΩ
−
+
3V
1kΩ
1MΩ
1MΩ
1.5V
3V
1V
VOUT
7. Input Offset Voltage, VIO
1kΩ
RLOAD
100µF
VDD
−VDD
100µF
Note: VIO = VOUT − 1.5V
9. Common Mode Input Voltage Range, VCM
Only for
Open Drain
1MΩ
10kΩ
1kΩ
−
3V
+
VIO
1kΩ
VIN
1MΩ
VIN = 0V
100µF VCML
1.5V
Note: VCML and VCMH are values of VIN when VIO
changes more than 50dB taking VIN = 0V
as reference.
Rev.2.00 Mar 10, 2006 page 19 of 22
10. Input Bias Current, IIB
A
VIN
VCMH
VIN
−
+
3V
HA1631S01/02/03/04 Series
11. Power Supply Rejection Ratio, PSRR
Only for
Open Drain
1MΩ
10kΩ
1kΩ
−
VDD/2
+
Measure
VOUT
1kΩ
Calculate VIO
PSRR Calculation
VDD
Point
1MΩ
|(VIO2 − VIO1)|
−1.8V VOUT1 VIO1 = VOUT1/1000
−VDD/2 100µF
PSRR = 20log10
5.5V − 1.8V
5.5V
VOUT2 VIO2 = VOUT2/1000
12. Common Mode Rejection Ratio, CMRR
Only for
Open Drain
1MΩ
10kΩ
1kΩ
−
1.5V
+
Measure
VOUT
1kΩ
Calculate VIO
CMRR Calculation
VIN
Point
VIN
1MΩ
|(VIO2 − VIO1)|
−1.5V VOUT1 VIO1 = VOUT1/1000
100µF
−1.5V
CMRR = 20log10
0.5V − (−1.5V)
0.5V
VOUT2 VIO2 = VOUT2/1000
13. Falling Time, Rising Time, Propagation Delay Time TPLH, TPHL
Only for
Open Drain
10kΩ
−
2V
±0.1V
±1.0V
+
C
Only for
Open Drain
10kΩ
−
+
LOAD
50Ω
50Ω
−1V 15pF
Overdrive = ±0.1V
input
50%
CLOAD
−1V 15pF
Overdrive = ±1.0V
input
50%
90%
50%
50%
output
2V
90%
output
10%
TPHL
TPLH
input
10%
tr
Only for Push Pull HA1631S01/02
50%
tf
input
50%
90%
50%
output
50%
output
10%
TPLH
TPHL
Only for Open Drain HA1631S03/04
Rev.2.00 Mar 10, 2006 page 20 of 22
tf
HA1631S01/02/03/04 Series
Mark Indication
(1) (2)
HA1631S01CM
HA1631S02CM
HA1631S03CM
HA1631S04CM
Rev.2.00 Mar 10, 2006 page 21 of 22
HA1631S01LP
HA1631S01LP
HA1631S01LP
HA1631S01LP
(1)
0
0
0
0
(2)
A
B
C
D
HA1631S01/02/03/04 Series
Package Dimensions
JEITA Package Code
RENESAS Code
SC-88A
Previous Code
PTSP0005ZC-A
D
MASS[Typ.]
CMPAK-5 / CMPAK-5V
0.006g
A
e
Q
c
E
HE
LP
L
A
A
x M
L1
S
Reference
Symbol
A3
b
A
A
A1
A2
A3
b
b1
c
c1
D
E
e
e
A2
A
A1
y S
S
e1
b
b1
l1
c1
c
b2
A-A Section
Package Name
MPAK-5
Pattern of terminal position areas
JEITA Package Code
SC-74A
RENESAS Code
PLSP0005ZB-A
Previous Code
MPAK-5 / MPAK-5V
HE
L
L1
LP
x
y
Dimension in Millimeters
Min
0.8
0
0.8
0.15
0.1
1.8
1.15
1.8
0.3
0.1
0.2
Nom
0.9
0.25
0.22
0.2
0.13
0.11
2.0
1.25
0.65
2.1
b2
e1
1.5
l1
Q
0.25
Max
1.1
0.1
1.0
0.3
0.15
2.2
1.35
2.4
0.7
0.5
0.6
0.05
0.05
0.35
0.9
MASS[Typ.]
0.015g
D
A
e
Q
E
HE
LP
L
A
c
Reference Dimension in Millimeters
Symbol
Min
Nom Max
L1
A3
A
x M S
A
b
e
A2
A
e1
A1
y S
S
b
b1
c1
c
I1
b2
A-A Section
Rev.2.00 Mar 10, 2006 page 22 of 22
Pattern of terminal position areas
A
A1
A2
A3
b
b1
c
c1
D
E
e
HE
L
L1
LP
x
y
b2
e1
I1
Q
1.0
0
1.0
0.35
0.1
2.8
1.5
2.5
0.3
0.1
0.2
1.1
0.25
0.42
0.4
0.13
0.11
2.95
1.6
0.95
2.8
1.3
0.1
1.2
0.5
0.15
3.1
1.8
3.0
0.7
0.5
0.6
0.05
0.05
0.55
2.15
0.85
0.3
Sales Strategic Planning Div.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Keep safety first in your circuit designs!
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble
may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary
circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's
application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party.
2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data,
diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of
publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is
therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product
information before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor
home page (http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to
evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes
no responsibility for any damage, liability or other loss resulting from the information contained herein.
5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life
is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a
product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater
use.
6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and
cannot be imported into a country other than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein.
http://www.renesas.com
RENESAS SALES OFFICES
Refer to "http://www.renesas.com/en/network" for the latest and detailed information.
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501
Renesas Technology Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900
Renesas Technology (Shanghai) Co., Ltd.
Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120
Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898
Renesas Technology Hong Kong Ltd.
7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2730-6071
Renesas Technology Taiwan Co., Ltd.
10th Floor, No.99, Fushing North Road, Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999
Renesas Technology Singapore Pte. Ltd.
1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
Renesas Technology Korea Co., Ltd.
Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea
Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145
Renesas Technology Malaysia Sdn. Bhd
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: <603> 7955-9390, Fax: <603> 7955-9510
© 2006. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .6.0
Similar pages