AD AD9164BBCZRL Dac update rate up to 12 gsp Datasheet

16-Bit, 12 GSPS,
RF DAC and Direct Digital Synthesizer
AD9164
Data Sheet
FEATURES
When combined with a 100 MHz serial peripheral interface (SPI)
and fast hop modes, phase coherent fast frequency hopping (FFH)
is enabled, with several modes to support multiple applications.
DAC update rate up to 12 GSPS (minimum)
Direct RF synthesis at 6 GSPS (minimum)
DC to 2.5 GHz in baseband mode
DC to 6 GHz in 2× nonreturn-to-zero (NRZ) mode
1.5 GHz to 7.5 GHz in Mix-Mode
Bypassable interpolation
2×, 3×, 4×, 6×, 8×, 12×, 16×, 24×
Excellent dynamic performance
In baseband mode, wide analog bandwidth capability combines
with high dynamic range to support DOCSIS 3.1 cable infrastructure compliance from the minimum of one carrier up to the full
maximum spectrum of 1.791 GHz of signal bandwidth. A 2×
interpolator filter (FIR85) enables the AD9164 to be configured
for lower data rates and converter clocking to reduce the overall
system power and ease the filtering requirements. In Mix-Mode™
operation, the AD9164 can reconstruct RF carriers in the second
and third Nyquist zones up to 7.5 GHz while still maintaining
exceptional dynamic range. The output current can be programmed
from 8 mA to 38.76 mA. The AD9164 data interface consists of
up to eight JESD204B serializer/deserializer (SERDES) lanes
that are programmable in terms of lane speed and number of
lanes to enable application flexibility.
APPLICATIONS
Broadband communications systems
DOCSIS 3.1 cable modem termination system (CMTS)/
video on demand (VOD)/edge quadrature amplitude
modulation (EQAM)
Wireless communications infrastructure
W-CDMA, LTE, LTE-A, point to point
GENERAL DESCRIPTION
An SPI interface configures the AD9164 and monitors the status of
all registers. The AD9164 is offered in an 165-ball, 8 mm × 8 mm,
0.5 mm pitch CSP_BGA package, and an 169-ball, 11 mm × 11 mm,
0.8 mm pitch, CSP_BGA package, including a leaded ball option.
The AD91641 is a high performance, 16-bit digital-to-analog
converter (DAC) and direct digital synthesizer (DDS) that
supports update rates to 6 GSPS. The DAC core is based on a
quad-switch architecture coupled with a 2× interpolator filter
that enables an effective DAC update rate of up to 12 GSPS in
some modes. The high dynamic range and bandwidth makes
these DACs ideally suited for the most demanding high speed
radio frequency (RF) DAC applications.
PRODUCT HIGHLIGHTS
The DDS consists of a bank of 32, 32-bit numerically controlled
oscillators (NCOs), each with its own phase accumulator.
3.
1.
2.
High dynamic range and signal reconstruction bandwidth
supports RF signal synthesis of up to 7.5 GHz.
Up to eight lanes JESD204B SERDES interface flexible in
terms of number of lanes and lane speed.
Bandwidth and dynamic range to meet DOCSIS 3.1
compliance and multiband wireless communications
standards with margin.
FUNCTIONAL BLOCK DIAGRAM
RESET
SDIO
SDO
CS
SCLK
IRQ
ISET VREF
VREF
AD9164
SPI
NRZ RZ MIX
SERDIN0±
INV
SINC
NCO
SYSREF±
HB
2×
HB
3×
HB
2×,
4×,
8×
TO JESD
TO DATAPATH
TX_ENABLE
DAC
CORE
OUTPUT±
CLOCK
DISTRIBUTION
CLK±
14414-001
HB
2×
JESD
DATA
LATCH
SERDIN7±
SYNCOUT±
Figure 1.
1
Protected by U.S. Patents 6,842,132 and 7,796,971.
Rev. A
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2016–2017 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD9164* Product Page Quick Links
Last Content Update: 01/10/2017
Comparable Parts
Design Resources
View a parametric search of comparable parts
• AD9161/AD9162/AD9163/AD9164 Evaluation Board
•
•
•
•
Documentation
Discussions
Data Sheet
• AD9164 16-Bit, 12 GSPS, RF DAC and Direct Digital
Synthesizer Data Sheet
View all AD9164 EngineerZone Discussions
Evaluation Kits
Tools and Simulations
• AD9164bbcaz IBIS Model
• AD9164bbcz IBIS Model
AD9164 Material Declaration
PCN-PDN Information
Quality And Reliability
Symbols and Footprints
Sample and Buy
Visit the product page to see pricing options
Technical Support
Submit a technical question or find your regional support
number
Reference Materials
Press
• D/A Converter Offers More Accuracy in a Smaller
Footprint for Diverse Applications Ranging from Radar to
Smartphone Testing
* This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet. Note: Dynamic changes to
the content on this page does not constitute a change to the revision number of the product data sheet. This content may be
frequently modified.
AD9164
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
JESD204B Overview .................................................................. 34
Applications ....................................................................................... 1
Physical Layer ............................................................................. 35
General Description ......................................................................... 1
Data Link Layer .......................................................................... 38
Product Highlights ........................................................................... 1
Transport Layer .......................................................................... 46
Functional Block Diagram .............................................................. 1
JESD204B Test Modes ............................................................... 48
Revision History ............................................................................... 3
JESD204B Error Monitoring..................................................... 50
Specifications..................................................................................... 4
Hardware Considerations ......................................................... 52
DC Specifications ......................................................................... 4
Main Digital Datapath ................................................................... 53
DAC Input Clock Overclocking Specifications ........................ 5
Data Format ................................................................................ 53
Power Supply DC Specifications ................................................ 5
Interpolation Filters ................................................................... 53
Serial Port and CMOS Pin Specifications ................................. 7
Digital Modulation ..................................................................... 56
JESD204B Serial Interface Speed Specifications ...................... 8
Inverse Sinc ................................................................................. 58
SYSREF± to DAC Clock Timing Specifications ....................... 8
Downstream Protection ............................................................ 59
Digital Input Data Timing Specifications ................................. 9
Datapath PRBS ........................................................................... 59
JESD204B Interface Electrical Specifications ........................... 9
Datapath PRBS IRQ ................................................................... 60
AC Specifications........................................................................ 10
Interrupt Request Operation ........................................................ 61
Absolute Maximum Ratings .......................................................... 11
Interrupt Service Routine .......................................................... 61
Reflow Profile .............................................................................. 11
Applications Information .............................................................. 62
Thermal Management ............................................................... 11
Hardware Considerations ......................................................... 62
Thermal Resistance .................................................................... 11
Analog Interface Considerations.................................................. 65
ESD Caution ................................................................................ 11
Analog Modes of Operation ..................................................... 65
Pin Configurations and Function Descriptions ......................... 12
Clock Input.................................................................................. 66
Typical Performance Characteristics ........................................... 16
Shuffle Mode ............................................................................... 67
Static Linearity ............................................................................ 16
DLL............................................................................................... 67
AC Performance (NRZ Mode) ................................................. 17
Voltage Reference ....................................................................... 67
AC (Mix-Mode) .......................................................................... 22
Temperature Sensor ................................................................... 67
DOCSIS Performance (NRZ Mode) ........................................ 25
Analog Outputs .......................................................................... 68
Terminology .................................................................................... 30
Start-Up Sequence .......................................................................... 71
Theory of Operation ...................................................................... 31
Register Summary .......................................................................... 73
Serial Port Operation ..................................................................... 32
Register Details ............................................................................... 82
Data Format ................................................................................ 32
Outline Dimensions ..................................................................... 135
Serial Port Pin Descriptions ...................................................... 32
Ordering Guide ........................................................................ 136
Serial Port Options ..................................................................... 32
JESD204B Serial Data Interface .................................................... 34
Rev. A | Page 2 of 136
Data Sheet
AD9164
REVISION HISTORY
1/2017—Rev. 0 to Rev. A
Deleted DLL_VDD_1P2 Parameter, Table 1 .....................................4
Added Temperature Sensor Parameter, Table 1 ................................4
Change to Endnote 1, Table 1 .................................................................4
Change to OUTPUT± to VNEG_N1P2 Parameter, Table 10 ....11
Changes to Link Delay Setup Example, With Known Delays
Section .......................................................................................................... 43
Changes to Link Delay Setup Example, Without Known Delay
Section .......................................................................................................... 45
Changes to Table 24 ................................................................................. 46
Added Datapath PRBS Section ......................................................59
Added Datapath PRBS IRQ Section .............................................60
Moved Figure 135 .....................................................................................67
Added Temperature Sensor Section.......................................................68
Changes to Equivalent DAC Output and Transfer Function
Section ..........................................................................................................68
Changes to Output Stage Configuration Section and Figure 142
Caption ..........................................................................................................69
Added Register 0x132 Row to Register 0x135 Row, Table 45 ... 74
Added Register 0x132 Row to Register 0x135 Row, Table 46 ... 91
Change to Register 0x230............................................................... 93
7/2016—Revision 0: Initial Version
Rev. A | Page 3 of 136
AD9164
Data Sheet
SPECIFICATIONS
DC SPECIFICATIONS
VDD25_DAC = 2.5 V, VDD12A = VDD12_CLK = 1.2 V, VNEG_N1P2 = −1.2 V, DVDD = 1.2 V, IOVDD = 2.5 V, VDD_1P2 =
DVDD_1P2 = PLL_LDO_VDD12 = 1.2 V, SYNC_VDD_3P3 = 3.3 V, DAC output full-scale current (IOUTFS) = 40 mA, and TA = −40°C to
+85°C, unless otherwise noted.
Table 1.
Parameter
RESOLUTION
DAC Update Rate
Minimum
Maximum
Adjusted4
ACCURACY
Integral Nonlinearity (INL)
Differential Nonlinearity (DNL)
ANALOG OUTPUTS
Gain Error (with Internal Reference)
Full-Scale Output Current
Minimum
Maximum
DAC CLOCK INPUT (CLK+, CLK−)
Differential Input Power
Common-Mode Voltage
Input Impedance1
TEMPERATURE DRIFT
Gain
Reference Voltage
TEMPERATURE SENSOR
Accuracy
REFERENCE
Internal Reference Voltage
ANALOG SUPPLY VOLTAGES
VDD25_DAC
VDD12A2
VDD12_CLK2
VNEG_N1P2
DIGITAL SUPPLY VOLTAGES
DVDD
IOVDD3
SERDES SUPPLY VOLTAGES
VDD_1P2
VTT_1P2
DVDD_1P2
PLL_LDO_VDD12
PLL_CLK_VDD12
SYNC_VDD_3P3
BIAS_VDD_1P2
Test Conditions/Comments
Min
16
Typ
Max
Unit
Bit
VDDx1 = 1.3 V ± 2%2
VDDx1 = 1.3 V ± 2%2, FIR853 2× interpolator enabled
VDDx1 = 1.3 V ± 2%2
6
12
6
1.5
6.4
12.8
6.4
GSPS
GSPS
GSPS
GSPS
±2.7
±1.7
LSB
LSB
−1.7
%
RSET = 9.76 kΩ
RSET = 9.76 kΩ
7.37
35.8
8
38.76
8.57
41.3
mA
mA
RLOAD = 90 Ω differential on-chip
AC-coupled
3 GSPS input clock
−20
0
0.6
90
+10
dBm
V
Ω
After single point calibration (See the Temperature Sensor section)
Includes VDD12_DCD/DLL
Can connect to VDD_1P2
Can connect to PLL_LDO_VDD12
Can connect to VDD_1P2
105
75
ppm/°C
ppm/°C
±5
%
1.19
V
2.375
1.14
1.14
−1.26
2.5
1.2
1.2
−1.2
2.625
1.326
1.326
−1.14
V
V
V
V
1.14
1.71
1.2
2.5
1.326
3.465
V
V
1.14
1.14
1.14
1.14
1.14
3.135
1.14
1.2
1.2
1.2
1.2
1.2
3.3
1.2
1.326
1.326
1.326
1.326
1.326
3.465
1.326
V
V
V
V
V
V
V
See the Clock Input section for more details.
For the lowest noise performance, use a separate power supply filter network for the VDD12_CLK and the VDD12A pins.
3
IOVDD can range from 1.8 V to 3.3 V, with ±5% tolerance.
4
The adjusted DAC update rate is calculated as fDAC divided by the minimum required interpolation factor. For the AD9164, the minimum interpolation factor is 1.
Therefore, with fDAC = 6 GSPS, fDAC adjusted = 6 GSPS. When FIR85 is enabled, which puts the device into 2× NRZ mode, fDAC = 2 × (DAC clock input frequency), and the
minimum interpolation increases to 2× (interpolation value). Thus, for the AD9164, with FIR85 enabled and DAC clock = 6 GSPS, fDAC = 12 GSPS, minimum interpolation = 2×, and
the adjusted DAC update rate = 6 GSPS.
1
2
Rev. A | Page 4 of 136
Data Sheet
AD9164
DAC INPUT CLOCK OVERCLOCKING SPECIFICATIONS
VDD25_DAC = 2.5 V, VDD12A = VDD12_CLK = 1.2 V, VNEG_N1P2 = −1.2 V, DVDD = 1.2 V, IOVDD = 2.5 V, VDD_1P2 =
DVDD_1P2 = PLL_LDO_VDD12 = 1.2 V, SYNC_VDD_3P3 = 3.3 V, IOUTFS = 40 mA, TA = −40°C to +85°C, unless otherwise noted.
Maximum guaranteed speed using the temperature and voltage conditions as shown in Table 2, where VDDx is VDD12_CLK, DVDD,
VDD_1P2, DVDD_1P2, and PLL_LDO_VDD12. Any DAC clock speed over 5.1 GSPS requires a maximum junction temperature that does not
exceed 105°C to avoid damage to the device. See Table 10 for details on maximum junction temperature permitted for certain clock
speeds.
Table 2.
Parameter1
MAXIMUM DAC UPDATE RATE
VDDx = 1.2 V ± 5%
VDDx = 1.2 V ± 2%
VDDx = 1.3 V ± 2%
1
Test Conditions/Comments
Min
TJMAX = 25°C
TJMAX = 85°C
TJMAX = 105°C
TJMAX = 25°C
TJMAX = 85°C
TJMAX = 105°C
TJMAX = 25°C
TJMAX = 85°C
TJMAX = 105°C
6.0
5.6
5.4
6.1
5.8
5.6
6.4
6.2
6.0
Typ
Max
Unit
GSPS
GSPS
GSPS
GSPS
GSPS
GSPS
GSPS
GSPS
GSPS
TJMAX is the maximum junction temperature.
POWER SUPPLY DC SPECIFICATIONS
IOUTFS = 40 mA, TA = −40°C to +85°C, unless otherwise noted. FIR85 is the finite impulse response with 85 dB digital attenuation.
Table 3.
Parameter
8 LANES, 2× INTERPOLATION (80%), 3 GSPS
Analog Supply Currents
VDD25_DAC = 2.5 V
VDD12A = 1.2 V
VDD12_CLK = 1.2 V
VNEG_N1P2 = −1.2 V
Digital Supply Currents
DVDD = 1.2 V
IOVDD1 = 2.5 V
SERDES Supply Currents
VDD_1P2 = 1.2 V
DVDD_1P2 = 1.2 V
PLL_LDO_VDD12 = 1.2 V
SYNC_VDD_3P3 = 3.3 V
8 LANES, 6× INTERPOLATION (80%), 3 GSPS
Analog Supply Currents
VDD25_DAC = 2.5 V
VDD12A = 1.2 V
VDD12_CLK = 1.2 V
VNEG_N1P2 = −1.2 V
Digital Supply Currents
DVDD = 1.2 V
IOVDD1 = 2.5 V
Test Conditions/Comments
NCO on, FIR85 on
Min
Typ
Max
Unit
100
150
279
−119
93.8
3.7
229
−112
mA
µA
mA
mA
Includes VDD12_DCD/DLL
621.3
2.5
971
2.7
mA
mA
Includes VTT_1P2, BIAS_VDD_1P2
425.5
62
84.4
9.3
550
86
106
11
mA
mA
mA
mA
Connected to PLL_CLK_VDD12
NCO on, FIR85 on
Includes VDD12_DCD/DLL
Rev. A | Page 5 of 136
93.8
3.7
228.7
−120.7
mA
µA
mA
mA
598.4
2.5
mA
mA
AD9164
Parameter
SERDES Supply Currents
VDD_1P2 = 1.2 V
DVDD_1P2 = 1.2 V
PLL_LDO_VDD12 = 1.2 V
SYNC_VDD_3P3 = 3.3 V
NCO ONLY MODE, 5 GSPS
Analog Supply Currents
VDD25_DAC = 2.5 V
VDD12A = 1.2 V
VDD12_CLK = 1.2 V
VNEG_N1P2 = −1.2 V
Digital Supply Currents
DVDD = 1.2 V
IOVDD1 = 2.5 V
SERDES Supply Currents
VDD_1P2 = 1.2 V
DVDD_1P2 = 1.2 V
PLL_LDO_VDD12 = 1.2 V
SYNC_VDD_3P3 = 3.3 V
8 LANES, 4× INTERPOLATION (80%), 5 GSPS
Analog Supply Currents
VDD25_DAC = 2.5 V
VDD12A = 1.2 V
VDD12_CLK = 1.2 V
Data Sheet
Test Conditions/Comments
Min
Includes VTT_1P2, BIAS_VDD_1P2
IOVDD1 = 2.5 V
SERDES Supply Currents
VDD_1P2 = 1.2 V
DVDD_1P2 = 1.2 V
PLL_LDO_VDD12 = 1.2 V
SYNC_VDD_3P3 = 3.3 V
8 LANES, 3× INTERPOLATION (80%), 4.5 GSPS
Analog Supply Currents
VDD25_DAC = 2.5 V
VDD12A = 1.2 V
VDD12_CLK = 1.2 V
VNEG_N1P2 = −1.2 V
Digital Supply Currents
DVDD = 1.2 V
IOVDD1 = 2.5 V
SERDES Supply Currents
VDD_1P2 = 1.2 V
DVDD_1P2 = 1.2 V
PLL_LDO_VDD12 = 1.2 V
SYNC_VDD_3P3 = 3.3 V
Max
443.4
72.3
81.8
9.4
Connected to PLL_CLK_VDD12
Unit
mA
mA
mA
mA
93.7
10
340.6
−112
100
150
432
mA
µA
mA
mA
Includes VDD12_DCD/DLL
425.5
2.5
753
2.7
mA
mA
Includes VTT_1P2, BIAS_VDD_1P2
1.4
1.0
0.13
0.32
34
14.1
1.5
0.43
mA
mA
mA
mA
102
80
340.5
408
−120.2
108
150
432.4
mA
µA
mA
mA
mA
665.4
706.5
894.6
1090
2.5
1033
2.7
mA
mA
mA
mA
mA
411.2
52.1
85.8
9.3
550
73
105
11
mA
mA
mA
mA
−119
Connected to PLL_CLK_VDD12
NCO on, FIR85 off (unless otherwise noted)
At 6 GSPS
VNEG_N1P2 = −1.2 V
Digital Supply Currents
DVDD = 1.2 V (Includes VDD12_DCD/DLL)
DVDD = 1.2 V
Typ
−127.4
NCO on, FIR85 off
NCO off, FIR85 on
NCO on, FIR85 on
NCO on, FIR85 on, at 6 GSPS
Includes VTT_1P2, BIAS_VDD_1P2
Connected to PLL_CLK_VDD12
NCO on, FIR85 on
94
85
314.3
−112.1
175
mA
µA
mA
mA
Includes VDD12_DCD/DLL
IOVDD = 2.5 V
948.5
2.5
mA
mA
Includes VTT_1P2, BIAS_VDD_1P2
432.3
62.3
84.7
9.2
mA
mA
mA
mA
Connected to PLL_CLK_VDD12
Rev. A | Page 6 of 136
Data Sheet
AD9164
Parameter
POWER DISSIPATION
3 GSPS
2× NRZ Mode, 6×, FIR85 Enabled, NCO On
NRZ Mode, 24×, FIR85 Disabled, NCO On
5 GSPS
NRZ Mode, 8×, FIR85 Disabled, NCO On
NRZ Mode, 16×, FIR85 Disabled, NCO On
2× NRZ Mode, 6×, FIR85 Enabled, NCO On
1
Test Conditions/Comments
Min
Typ
Max
Unit
Using 80%, 3× filter, eight-lane JESD204B
Using 80%, 2× filter, one-lane JESD204B
2.1
1.3
W
W
Using 80%, 2× filter, eight-lane JESD204B
Using 80%, 2× filter, eight-lane JESD204B
Using 80%, 3× filter, eight-lane JESD204B
2.18
2.09
2.65
W
W
W
IOVDD can range from 1.8 V to 3.3 V, with ±5% tolerance.
SERIAL PORT AND CMOS PIN SPECIFICATIONS
VDD25_DAC = 2.5 V, VDD12A = VDD12_CLK = 1.2 V, VNEG_N1P2 = −1.2 V, DVDD = 1.2 V, IOVDD = 2.5 V, VDD_1P2 =
DVDD_1P2 = PLL_LDO_VDD12 = 1.2 V, SYNC_VDD_3P3 = 3.3 V, IOUTFS = 40 mA, TA = −40°C to +85°C, unless otherwise noted.
Table 4.
Parameter
WRITE OPERATION
Maximum SCLK Clock Rate
SCLK Clock High
SCLK Clock Low
SDIO to SCLK Setup Time
SCLK to SDIO Hold Time
CS to SCLK Setup Time
SCLK to CS Hold Time
READ OPERATION
SCLK Clock Rate
SCLK Clock High
SCLK Clock Low
SDIO to SCLK Setup Time
SCLK to SDIO Hold Time
CS to SCLK Setup Time
SCLK to SDIO (or SDO) Data Valid Time
CS to SDIO (or SDO) Output Valid to High-Z
INPUTS (SDIO, SCLK, CS, RESET, TX_ENABLE)
Voltage Input
High
Low
Current Input
High
Low
OUTPUTS (SDIO, SDO)
Voltage Output
High
Low
Current Output
High
Low
Symbol
fSCLK, 1/tSCLK
tPWH
tPWL
tDS
tDH
tS
tH
Test Comments/Conditions
See Figure 90
SCLK = 20 MHz
SCLK = 20 MHz
Min
100
3.5
4
4
1
9
9
Typ
Max
Unit
MHz
ns
ns
ns
ns
ns
ns
2
0.5
1
0.5
See Figure 89
fSCLK, 1/tSCLK
tPWH
tPWL
tDS
tDH
tS
tDV
20
Not shown in Figure 89 or Figure 90
VIH
VIL
1.8 V ≤ IOVDD ≤ 2.5 V
1.8 V ≤ IOVDD ≤ 2.5 V
IIH
IIL
VOH
VOL
17
45
MHz
ns
ns
ns
ns
ns
ns
ns
0.3 × IOVDD
V
V
20
20
10
5
10
0.7 × IOVDD
75
−150
1.8 V ≤ IOVDD ≤ 3.3 V
1.8 V ≤ IOVDD ≤ 3.3 V
IOH
IOL
0.8 × IOVDD
0.2 × IOVDD
4
4
Rev. A | Page 7 of 136
µA
µA
V
V
mA
mA
AD9164
Data Sheet
JESD204B SERIAL INTERFACE SPEED SPECIFICATIONS
VDD25_DAC = 2.5 V, VDD12A = VDD12_CLK = 1.2 V, VNEG_N1P2 = −1.2 V, DVDD = 1.2 V, IOVDD = 2.5 V, VDD_1P2 =
DVDD_1P2 = PLL_LDO_VDD12 = 1.2 V, SYNC_VDD_3P3 = 3.3 V, IOUTFS = 40 mA, TA = −40°C to +85°C, unless otherwise noted.
Table 5.
Parameter
SERIAL INTERFACE SPEED
Half Rate
Full Rate
Oversampling
2× Oversampling
Test Conditions/Comments
Guaranteed operating range
Min
Typ
6
3
1.5
0.750
Max
Unit
12.5
6.25
3.125
1.5625
Gbps
Gbps
Gbps
Gbps
SYSREF± TO DAC CLOCK TIMING SPECIFICATIONS
VDD25_DAC = 2.5 V, VDD12A = VDD12_CLK = 1.2 V, VNEG_N1P2 = −1.2 V, DVDD = 1.2 V, IOVDD = 2.5 V, VDD_1P2 =
DVDD_1P2 = PLL_LDO_VDD12 = 1.2 V, SYNC_VDD_3P3 = 3.3 V, IOUTFS = 40 mA, TA = −40°C to +85°C, unless otherwise noted.
Table 6.
Parameter1
SYSREF± (AD9164BBCZ ONLY)
SYSREF± Differential Swing = 0.4 V
Minimum Setup Time, tSYSS
Minimum Hold Time, tSYSH
SYSREF± Differential Swing = 0.8 V
Minimum Setup Time, tSYSS
Minimum Hold Time, tSYSH
SYSREF± Differential Swing = 1.0 V
Minimum Setup Time, tSYSS
Minimum Hold Time, tSYSH
SYSREF± (AD9164BBCAZ ONLY)
SYSREF± Differential Swing = 1.0 V
Minimum Setup Time, tSYSS
Minimum Hold Time, tSYSH
AC-coupled
DC-coupled, common-mode voltage = 0 V
DC-coupled, common-mode voltage = 1.25 V
AC-coupled
DC-coupled, common-mode voltage = 0 V
DC-coupled, common-mode voltage = 1.25 V
Min
Typ
Max
Unit
163
160
424
318
ps
ps
162
169
412
350
ps
ps
163
176
376
354
ps
ps
65
45
68
19
5
51
117
77
129
63
37
114
ps
ps
ps
ps
ps
ps
The SYSREF± pulse must be at least four DAC clock edges wide plus the setup and hold times in Table 6. For more information, see the Sync Processing Modes
Overview section.
tSYSS
tSYSH
SYSREF+
CLK+
MIN 4 DAC CLOCK EDGES
Figure 2. SYSREF± to DAC Clock Timing Diagram (Only SYSREF+ and CLK+ Shown)
Rev. A | Page 8 of 136
14414-002
1
Test Conditions/Comments
DC-coupled, common-mode voltage = 1.2 V
Data Sheet
AD9164
DIGITAL INPUT DATA TIMING SPECIFICATIONS
VDD25_DAC = 2.5 V, VDD12A = VDD12_CLK = 1.2 V, VNEG_N1P2 = −1.2 V, DVDD = 1.2 V, IOVDD = 2.5 V, VDD_1P2 =
DVDD_1P2 = PLL_LDO_VDD12 = 1.2 V, SYNC_VDD_3P3 = 3.3 V, IOUTFS = 40 mA, TA = −40°C to +85°C, unless otherwise noted.
Table 7.
Parameter
LATENCY1
Interface
Interpolation
Power-Up Time
DETERMINISTIC LATENCY
Fixed
Variable
SYSREF± TO LOCAL MULTIFRAME
CLOCKS (LMFC) DELAY
Test Conditions/Comments
Min
From DAC output off to enabled
Typ
Max
Unit
1
See Table 33
10
PCLK2 cycle
ns
12
2
PCLK2 cycles
PCLK2 cycles
DAC clock cycles
4
Total latency (or pipeline delay) through the device is calculated as follows:
Total Latency = Interface Latency + Fixed Latency + Variable Latency + Pipeline Delay
See Table 33 for examples of the pipeline delay per block.
2
PCLK is the internal processing clock for the AD9164 and equals the lane rate ÷ 40.
1
JESD204B INTERFACE ELECTRICAL SPECIFICATIONS
VDD25_DAC = 2.5 V, VDD12A = VDD12_CLK = 1.2 V, VNEG_N1P2 = −1.2 V, DVDD = 1.2 V, IOVDD = 2.5 V, VDD_1P2 = DVDD_1P2 =
PLL_LDO_VDD12 = 1.2 V, SYNC_VDD_3P3 = 3.3 V, IOUTFS = 40 mA, TA = −40°C to +85°C, unless otherwise noted. VTT is the termination
voltage.
Table 8.
Parameter
JESD204B DATA INPUTS
Input Leakage Current
Logic High
Logic Low
Unit Interval
Common-Mode Voltage
Differential Voltage
VTT Source Impedance
Differential Impedance
Differential Return Loss
Common-Mode Return Loss
SYSREF± INPUT
Differential Impedance
DIFFERENTIAL OUTPUTS (SYNCOUT±)2
Output Differential Voltage
Output Offset Voltage
1
2
Symbol
Test Conditions/Comments
Min
TA = 25°C
Input level = 1.2 V ± 0.25 V, VTT = 1.2 V
Input level = 0 V
UI
VRCM
R_VDIFF
ZTT
ZRDIFF
RLRDIF
RLRCM
AC-coupled, VTT = VDD_1P21
At dc
At dc
80
−0.05
110
80
Rev. A | Page 9 of 136
Unit
1333
+1.85
1050
30
120
µA
µA
ps
V
mV
Ω
Ω
dB
dB
100
8
6
110
121
350
1.15
As measured on the input side of the ac coupling capacitor.
IEEE Standard 1596.3 LVDS compatible.
Max
10
−4
165-ball CSP_BGA
169-ball CSP_BGA
Driving 100 Ω differential load
VOD
VOS
Typ
420
1.2
Ω
Ω
450
1.27
mV
V
AD9164
Data Sheet
AC SPECIFICATIONS
VDD25_DAC = 2.5 V, VDD12A = VDD12_CLK = 1.2 V, VNEG_N1P2 = −1.2 V, DVDD = 1.2 V, IOVDD = 2.5 V, VDD_1P2 =
DVDD_1P2 = PLL_LDO_VDD12 = 1.2 V, SYNC_VDD_3P3 = 3.3 V, IOUTFS = 40 mA, TA = +25°C.
Table 9.
Parameter
SPURIOUS-FREE DYNAMIC RANGE (SFDR)1
Single Tone, fDAC = 5000 MSPS
fOUT = 70 MHz
fOUT = 500 MHz
fOUT = 1000 MHz
fOUT = 2000 MHz
fOUT = 4000 MHz
Single Tone, fDAC = 5000 MSPS
fOUT = 70 MHz
fOUT = 500 MHz
fOUT = 1000 MHz
fOUT = 2000 MHz
fOUT = 4000 MHz
DOCSIS
fOUT = 70 MHz
fOUT = 70 MHz
fOUT = 70 MHz
fOUT = 950 MHz
fOUT = 950 MHz
fOUT = 950 MHz
Wireless Infrastructure
fOUT = 960 MHz
fOUT = 1990 MHz
ADJACENT CHANNEL POWER
fOUT = 877 MHz
fOUT = 877 MHz
fOUT = 1887 MHz
fOUT = 1980 MHz
INTERMODULATION DISTORTION
fOUT = 900 MHz
fOUT = 900 MHz
fOUT = 1800 MHz
fOUT = 1800 MHz
NOISE SPECTRAL DENSITY (NSD)
Single Tone, fDAC = 5000 MSPS
fOUT = 550 MHz
fOUT = 960 MHz
fOUT = 1990 MHz
SINGLE SIDEBAND (SSB) PHASE NOISE AT OFFSET
1 kHz
10 kHz
100 kHz
1 MHz
10 MHz
1
Test Conditions/Comments
Min
FIR85 enabled
−6 dBFS, shuffle enabled
FIR85 enabled
fDAC = 3076 MSPS
Single carrier
Four carriers
Eight carriers
Single carrier
Four carriers
Eight carriers
fDAC = 5000 MSPS
Two-carrier GSM signal at −9 dBFS; across 925 MHz to
960 MHz band
Two-carrier GSM signal at −9 dBFS; across 1930 MHz to
1990 MHz band
fDAC = 5000 MSPS
One carrier, first adjacent channel
Two carriers, first adjacent channel
One carrier, first adjacent channel
Four carriers, first adjacent channel
fDAC = 5000 MSPS, two-tone test
0 dBFS
−6 dBFS, shuffle enabled
0 dBFS
−6 dBFS, shuffle enabled
Typ
Max
Unit
−82
−75
−65
−70
−60
dBc
dBc
dBc
dBc
dBc
−75
−75
−70
−75
−65
dBc
dBc
dBc
dBc
dBc
−70
−70
−67
−70
−68
−64
dBc
dBc
dBc
dBc
dBc
dBc
−85
dBc
−81
dBc
−79
−76
−74
−70
dBc
dBc
dBc
dBc
−80
−80
−68
−78
dBc
dBc
dBc
dBc
−168
−167
−164
dBm/Hz
dBm/Hz
dBm/Hz
−119
−125
−135
−144
−156
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
fOUT = 3800 MHz, fDAC = 4000 MSPS
See the Clock Input section for more details on optimizing SFDR and reducing the image of the fundamental with clock input tuning.
Rev. A | Page 10 of 136
Data Sheet
AD9164
ABSOLUTE MAXIMUM RATINGS
Table 10.
1
Rating
−0.3 V to VDD25_DAC + 0.3 V
−0.3 V to SYNC_VDD_3P3 + 0.3 V
CUSTOMER CASE (HEAT SINK)
−0.3 V to VDD25_DAC + 0.2 V
GND − 0.5 V to +2.5 V
−0.3 V to VDD12_CLK + 0.3 V
−0.3 V to IOVDD + 0.3 V
CUSTOMER THERMAL FILLER
SILICON (DIE)
IC PROFILE
PACKAGE SUBSTRATE
14414-700
Parameter
ISET, VREF to VBG_NEG
SERDINx±, VTT_1P2,
SYNCOUT±
OUTPUT± to VNEG_N1P2
SYSREF±
CLK± to Ground
RESET, IRQ, CS, SCLK, SDIO,
SDO to Ground
Junction Temperature1
fDAC = 6 GSPS
fDAC ≤ 5.1 GSPS
Ambient Operating
Temperature Range (TA)
Storage Temperature Range
Figure 3 shows the profile view of the device mounted to a user
printed circuit board (PCB) and a heat sink (typically the
aluminum case) to keep the junction (exposed die) below the
maximum junction temperature in Table 10.
CUSTOMER PCB
105°C
110°C
−40°C to +85°C
Figure 3. Typical Thermal Management Solution
THERMAL RESISTANCE
−65°C to +150°C
Some operating modes of the device may cause the device to approach or
exceed the maximum junction temperature during operation at supported
ambient temperatures. Removal of heat from the device may require
additional measures such as active airflow, heat sinks, or other measures.
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
REFLOW PROFILE
The AD9164 reflow profile is in accordance with the JEDEC
JESD204B criteria for Pb-free devices. The maximum reflow
temperature is 260°C.
THERMAL MANAGEMENT
The AD9164 is a high power device that can dissipate nearly
3 W depending on the user application and configuration.
Because of the power dissipation, the AD9164 uses an exposed
die package to give the customer the most effective method of
controlling the die temperature. The exposed die allows cooling
of the die directly.
Typical θJA and θJC values are specified for a 4-layer JEDEC 2S2P
high effective thermal conductivity test board for balled
surface-mount packages. θJA is obtained in still air conditions
(JESD51-2). Airflow increases heat dissipation, effectively reducing
θJA. θJC is obtained with the test case temperature monitored at
the bottom of the package.
ΨJT is thermal characteristic parameters obtained with θJA in still
air test conditions but are not applicable to the CSP_BGA package.
Estimate the junction temperature (TJ) using the following
equations:
TJ = TT + (ΨJT × PDISS)
where:
TT is the temperature measured at the top of the package.
PDISS is the total device power dissipation.
Table 11. Thermal Resistance
Package Type
165-Ball CSP_BGA
169-Ball CSP_BGA
ESD CAUTION
Rev. A | Page 11 of 136
θJA
15.4
14.6
θJC
0.04
0.02
Unit
°C/W
°C/W
AD9164
Data Sheet
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
2
3
4
5
7
8
OUTPUT–
OUTPUT+
6
VNEG_N1P2 VDD25_DAC VNEG_N1P2 VNEG_N1P2 VDD25_DAC VDD25_DAC
9
11
10
12
VDD25_DAC VDD25_DAC VNEG_N1P2 VNEG_N1P2
13
14
15
VSS
VSS
ISET
A
VDD12A
VDD12A
VREF
B
B
VSS
VSS
VDD25_DAC VNEG_N1P2 VNEG_N1P2 VDD25_DAC VDD25_DAC VDD25_DAC VDD25_DAC VNEG_N1P2 VNEG_N1P2 VDD25_DAC
C
CLK+
VSS
VDD25_DAC VNEG_N1P2 VNEG_N1P2 VDD25_DAC VDD25_DAC VNEG_N1P2 VNEG_N1P2 VDD25_DAC
D
CLK–
VSS
VSS
VSS
VSS
VSS
D
E
VSS
VSS
VSS
VSS
VSS
VDD12_CLK
E
VDD12_CLK VDD12_CLK VDD12_CLK
F
F
VDD12_CLK VDD12_CLK VDD12_CLK
VSS
VSS
VDD12_DCD/ VDD12_DCD/
DLL
DLL
VNEG_N1P2 VDD25_DAC C
VBG_NEG
VSS
VSS
VSS
VSS
VDD12_
DCD/DLL
VDD12_
DCD/DLL
VSS
VSS
CS
G
G
IRQ
VSS
VSS
H
VSS
TX_ENABLE
VSS
VSS
VSS
VSS
VSS
VSS
VSS
SDO
VSS
H
J
SERDIN7+
VDD_1P2
RESET
VSS
VSS
VSS
VSS
VSS
SCLK
VDD_1P2
SERDIN0+
J
K
SERDIN7–
VDD_1P2
IOVDD
DVDD
DVDD
DVDD
DVDD
DVDD
SDIO
VDD_1P2
SERDIN0–
K
L
VSS
VSS
DVDD_1P2
DVDD_1P2
VSS
VSS
L
M
SERDIN6+
VDD_1P2
VTT_1P2
VTT_1P2
VDD_1P2
SERDIN1+
M
N
SERDIN6–
VDD_1P2
VDD_1P2
SERDIN1–
N
P
VSS
SYNC_
VDD_3P3
R
BIAS_VDD_
1P2
1
SYSREF+
SYSREF–
VSS
VSS
PLL_CLK_
VDD12
PLL_LDO_
VDD12
VSS
SYNCOUT–
SYNCOUT+
VDD_1P2
VDD_1P2
DNC
VDD_1P2
VDD_1P2
PLL_LDO_
BYPASS
VDD_1P2
VDD_1P2
DNC
VDD_1P2
VDD_1P2
SYNC_
VDD_3P3
VSS
P
VSS
SERDIN5+
SERDIN5–
VSS
SERDIN4+
SERDIN4–
VSS
SERDIN3–
SERDIN3+
VSS
SERDIN2–
SERDIN2+
VSS
BIAS_
VDD_1P2
R
2
3
4
5
6
7
8
9
10
11
12
13
14
15
–1.2V ANALOG SUPPLY V
2.5V ANALOG SUPPLY V
1.2V DAC SUPPLY V
GROUND
1.2V DAC CLK SUPPLY V
SERDES INPUT
SERDES 3.3V VCO SUPPLY V
SERDES 1.2V SUPPLY V
DAC RF SIGNALS
SYSREF±/SYNCOUT±
CMOS I/O
IOVDD
REFERENCE
DNC = DO NOT CONNECT.
14414-003
1
A
Figure 4. 165-Ball CSP_BGA Pin Configuration
Table 12. 165-Ball CSP_BGA Pin Function Descriptions
Pin No.
A1, A3, A4, A11, A12, B4, B5, B10, B11, C5, C6, C9, C10, C14
A2, A5, A6, A9, A10, B3, B6, B7, B8, B9, B12, C4, C7, C8, C11,
C15
A7
A8
A13, A14, B1, B2, C2, D2, D3, D13, D14, D15, E1, E2, E3, E13,
E14, F6, F7, F8, F9, F10, G2, G3, G8, G13, G14, H1, H3, H6,
H7, H8, H9, H10, H13, H15, J6, J7, J8, J9, J10, L1, L2, L14,
L15, N6, N7, N10, P1, P15, R2, R5, R8, R11, R14
A15
Mnemonic
VNEG_N1P2
VDD25_DAC
Description
−1.2 V Analog Supply Voltage.
2.5 V Analog Supply Voltage.
OUTPUT−
OUTPUT+
VSS
DAC Negative Current Output.
DAC Positive Current Output.
Supply Return. Connect these pins to ground.
ISET
B13, B14
B15
VDD12A
VREF
C1, D1
C12
CLK+, CLK−
VBG_NEG
E15, F1, F2, F3, F13, F14, F15
G1
G6, G7, G9, G10
VDD12_CLK
IRQ
VDD12_DCD/DLL
Reference Current. Connect this pin to VNEG_N1P2 with
a 9.6 kΩ resistor.
1.2 V Analog Supply Voltage.
1.2 V Reference Input/Output. Connect this pin to VSS
with a 1 µF capacitor.
Positive and Negative DAC Clock Inputs.
−1.2 V Reference. Connect this pin to VNEG_N1P2 with
a 0.1 µF capacitor.
1.2 V Clock Supply Voltage.
Interrupt Request Output (Active Low, Open Drain).
1.2 V Digital Supply Voltage.
Rev. A | Page 12 of 136
Data Sheet
AD9164
Pin No.
G15
Mnemonic
CS
H14
SDO
J13
SCLK
K13
SDIO
J3
RESET
H2
TX_ENABLE
P5, P11
J2, J14, K2, K14, M2, M14, N2, N14, P3, P4, P6, P7, P9, P10,
P12, P13
K3
DNC
VDD_1P2
K6, K7, K8, K9, K10
L3, L13
M3, M13
J1, K1
IOVDD
N4, N5
DVDD
DVDD_1P2
VTT_1P2
SERDIN7+,
SERDIN7−
SERDIN6+,
SERDIN6−
SERDIN5+,
SERDIN5−
SERDIN4+,
SERDIN4SERDIN3−,
SERDIN3+
SERDIN2−,
SERDIN2+
SERDIN1+,
SERDIN1−
SERDIN0+,
SERDIN0−
SYSREF+, SYSREF−
N8
PLL_CLK_VDD12
N9
N11, N12
PLL_LDO_VDD12
SYNCOUT−,
SYNCOUT+
SYNC_VDD_3P3
PLL_LDO_BYPASS
BIAS_VDD_1P2
M1, N1
R3, R4
R6, R7
R9, R10
R12, R13
M15, N15
J15, K15
P2, P14
P8
R1, R15
Rev. A | Page 13 of 136
Description
Serial Port Chip Select Bar (Active Low) Input. CMOS
levels on this pin are determined with respect to
IOVDD.
Serial Port Data Output. CMOS levels on this pin are
determined with respect to IOVDD.
Serial Port Data Clock. CMOS levels on this pin are
determined with respect to IOVDD.
Serial Port Data Input/Output. CMOS levels on this pin
are determined with respect to IOVDD.
Reset Bar (Active Low) Input. CMOS levels on this pin
are determined with respect to IOVDD.
Transmit Enable Input. This pin can be used instead of
the DAC output bias power-down bits in Register
0x040, Bits[1:0] to enable the DAC output. CMOS levels
are determined with respect to IOVDD.
Do Not Connect. Do not connect to these pins.
1.2 V SERDES Digital Supply.
Supply Voltage for CMOS Input/Output and SPI.
Operational for 1.8 V to 3.3 V plus tolerance (see Table 1
for details).
1.2 V Digital Supply Voltage.
1.2 V SERDES Digital Supply Voltage.
1.2 V SERDES VTT Digital Supply Voltage.
SERDES Lane 7 Positive and Negative Inputs.
SERDES Lane 6 Positive and Negative Inputs.
SERDES Lane 5 Positive and Negative Inputs.
SERDES Lane 4 Positive and Negative Inputs.
SERDES Lane 3 Negative and Positive Inputs.
SERDES Lane 2 Negative and Positive Inputs.
SERDES Lane 1 Positive and Negative Inputs.
SERDES Lane 0 Positive and Negative Inputs.
System Reference Positive and Negative Inputs. These
pins are self biased for ac coupling. They can be
ac-coupled or dc-coupled.
1.2 V SERDES Phase-Locked Loop (PLL) Clock Supply
Voltage.
1.2 V SERDES PLL Supply.
Negative and Positive LVDS Sync (Active Low) Output
Signals.
3.3 V SERDES Sync Supply Voltage.
1.2 V SERDES PLL Supply Voltage Bypass.
1.2 V SERDES Supply Voltage.
AD9164
Data Sheet
1
2
3
4
5
6
7
8
9
10
11
12
13
A
VSS
VNEG_N1P2
VDD25_DAC
VNEG_N1P2
VDD25_DAC
OUTPUT–
OUTPUT+
VDD25_DAC
VNEG_N1P2
VDD25_DAC
VSS
ISET
VREF
A
B
CLK+
VSS
VSS
VDD25_DAC
VNEG_N1P2
VDD25_DAC
VDD25_DAC
VNEG_N1P2
VDD25_DAC
VDD12A
VDD12A
VDD25_DAC
VNEG_N1P2
B
C
CLK–
VSS
VSS
VSS
VDD25_DAC
VNEG_N1P2
VNEG_N1P2
VDD25_DAC
VBG_NEG
VSS
VSS
VSS
VSS
C
D
VSS
VDD12_CLK
VDD12_CLK
VDD12_CLK
VDD12_CLK
VSS
VSS
VDD12_CLK
VDD12_CLK
VDD12_CLK
VDD12_CLK
VDD12_CLK
VDD12_CLK
D
E
VDD12_CLK
VSS
VSS
VSS
DVDD
DVDD
VSS
DVDD
DVDD
VSS
VSS
VSS
VSS
E
F
SYSREF+
SYSREF–
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
CS
VSS
F
G
VSS
VSS
TX_ENABLE
IRQ
DVDD
DVDD
DVDD
DVDD
DVDD
SDIO
SDO
VSS
VSS
G
H
SERDIN7+
SERDIN7–
VDD_1P2
RESET
IOVDD
DVDD_1P2
VSS
DVDD_1P2
IOVDD
SCLK
VDD_1P2
SERDIN0–
SERDIN0+
H
J
VSS
VSS
VDD_1P2
DNC
DNC
VSS
VSS
VSS
SYNCOUT–
SYNCOUT+
VDD_1P2
VSS
VSS
J
K
SERDIN6+
SERDIN6–
VTT_1P2
SYNC_
VDD_3P3
DNC
VSS
PLL_CLK_
VDD12
PLL_LDO_
VDD12
DNC
SYNC_
VDD_3P3
VTT_1P2
SERDIN1–
SERDIN1+
K
L
VSS
VSS
VDD_1P2
VDD_1P2
VDD_1P2
VSS
DNC
VSS
VDD_1P2
VDD_1P2
VDD_1P2
VSS
VSS
L
M
VSS
VSS
SERDIN5+
VSS
SERDIN4+
VSS
PLL_LDO_
BYPASS
VSS
SERDIN3+
VSS
SERDIN2+
VSS
VSS
M
VSS
SERDIN5–
VSS
SERDIN4–
VSS
VSS
VSS
SERDIN3–
VSS
SERDIN2–
VSS
BIAS_
VDD_1P2
N
2
3
4
5
6
7
8
9
10
11
12
13
1
–1.2V ANALOG SUPPLY V
2.5V ANALOG SUPPLY V
1.2V DAC SUPPLY V
GROUND
1.2V DAC CLK SUPPLY V
SERDES INPUT
SERDES 3.3V VCO SUPPLY V
SERDES 1.2V SUPPLY V
DAC RF SIGNALS
SYSREF±/SYNCOUT±
CMOS I/O
IOVDD
DNC = DO NOT CONNECT.
REFERENCE
14414-004
N BIAS_VDD_1P2
Figure 5. 169-Ball CSP_BGA Pin Configuration
Table 13. 169-Ball CSP_BGA Pin Function Descriptions
Pin No.
A1, A11, B2, B3, C2, C3, C4, C10, C11, C12, C13, D1, D6, D7, E2,
E3, E4, E7, E10, E11, E12, E13, F3, F4, F5, F6, F7, F8, F9, F10,
F11, F13, G1, G2, G12, G13, H7, J1, J2, J6, J7, J8, J12, J13, K6,
L1, L2, L6, L8, L12, L13, M1, M2, M4, M6, M8, M10, M12, M13,
N2, N4, N6, N7, N8, N10, N12
A2, A4, A9, B5, B8, B13, C6, C7
A3, A5, A8, A10, B4, B6, B7, B9, B12, C5, C8
A6
A7
A12
Mnemonic
VSS
Description
Supply Return. Connect these pins to ground.
VNEG_N1P2
VDD25_DAC
OUTPUT−
OUTPUT+
ISET
A13
VREF
B1, C1
B10, B11
C9
CLK+, CLK−
VDD12A
VBG_NEG
D2, D3, D4, D5, D8, D9, D10, D11, D12, D13, E1
E5, E6, E8, E9, G5, G6, G7, G8, G9
VDD12_CLK
DVDD
−1.2 V Analog Supply Voltage.
2.5 V Analog Supply Voltage.
DAC Negative Current Output.
DAC Positive Current Output.
Reference Current. Connect this pin to VNEG_N1P2
with a 9.6 kΩ resistor.
1.2 V Reference Input/Output. Connect this pin to VSS
with a 1 µF capacitor.
Positive and Negative DAC Clock Inputs.
1.2 V Analog Supply Voltage.
−1.2 V Reference. Connect this pin to VNEG_N1P2
with a 0.1 µF capacitor.
1.2 V Clock Supply Voltage.
1.2 V Digital Supply Voltage.
Rev. A | Page 14 of 136
Data Sheet
AD9164
Pin No.
F1, F2
Mnemonic
SYSREF+, SYSREF−
F12
CS
G3
TX_ENABLE
G4
G10
IRQ
SDIO
G11
SDO
H10
SCLK
H3, H11, J3, J11, L3, L4, L5, L9, L10, L11
H4
VDD_1P2
RESET
H5, H9
IOVDD
H6, H8
H1, H2
DVDD_1P2
SERDIN7+,
SERDIN7−
SERDIN6+,
SERDIN6−
SERDIN5+,
SERDIN5−
SERDIN4+,
SERDIN4−
SERDIN3+,
SERDIN3−
SERDIN2+,
SERDIN2−
SERDIN1−,
SERDIN1+
SERDIN0−,
SERDIN0+
DNC
SYNCOUT−,
SYNCOUT+
VTT_1P2
SYNC_VDD_3P3
PLL_CLK_VDD12
PLL_LDO_VDD12
PLL_LDO_BYPASS
BIAS_VDD_1P2
K1, K2
M3, N3
M5, N5
M9, N9
M11, N11
K12, K13
H12, H13
J4, J5, K5, K9, L7
J9, J10
K3, K11
K4, K10
K7
K8
M7
N1, N13
Rev. A | Page 15 of 136
Description
System Reference Positive and Negative Inputs. These
pins are self biased for ac coupling. They can be accoupled or dc-coupled.
Serial Port Chip Select Bar (Active Low) Input. CMOS
levels on this pin are determined with respect to IOVDD.
Transmit Enable Input. This pin can be used instead of
the DAC output bias power-down bits in Register 0x040,
Bits[1:0] to enable the DAC output. CMOS levels are
determined with respect to IOVDD.
Interrupt Request Output (Active Low, Open Drain).
Serial Port Data Input/Output. CMOS levels on this
pin are determined with respect to IOVDD.
Serial Port Data Output. CMOS levels on this pin are
determined with respect to IOVDD.
Serial Port Data Clock. CMOS levels on this pin are
determined with respect to IOVDD.
1.2 V SERDES Digital Supply.
Reset Bar (Active Low) Input. CMOS levels on this pin
are determined with respect to IOVDD.
Supply Voltage for CMOS Input/Output and SPI.
Operational for 1.8 V to 3.3 V (see Table 1 for details).
1.2 V SERDES Digital Supply Voltage.
SERDES Lane 7 Positive and Negative Inputs.
SERDES Lane 6 Positive and Negative Inputs.
SERDES Lane 5 Positive and Negative Inputs.
SERDES Lane 4 Positive and Negative Inputs.
SERDES Lane 3 Positive and Negative Inputs.
SERDES Lane 2 Positive and Negative Inputs.
SERDES Lane 1 Negative and Positive Inputs.
SERDES Lane 0 Negative and Positive Inputs.
Do Not Connect. Do not connect to these pins.
Negative and Positive LVDS Sync (Active Low) Output
Signals.
1.2 V SERDES VTT Digital Supply Voltage.
3.3 V SERDES Sync Supply Voltage.
1.2 V SERDES PLL Clock Supply Voltage.
1.2 V SERDES PLL Supply.
1.2 V SERDES PLL Supply Voltage Bypass.
1.2 V SERDES Supply Voltage.
AD9164
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
STATIC LINEARITY
IOUTFS = 40 mA, nominal supplies, TA = 25°C, unless otherwise noted.
15
4
2
10
–2
DNL (LSB)
INL (LSB)
0
5
–4
0
–6
–8
–5
–12
0
10000
20000
30000
40000
50000
60000
CODE
14414-005
–10
0
10000
20000
30000
40000
50000
60000
CODE
14414-008
–10
Figure 9. DNL, IOUTFS = 20 mA
Figure 6. INL, IOUTFS = 20 mA
4
15
2
10
5
–2
DNL (LSB)
INL (LSB)
0
0
–4
–6
–8
–5
0
10000
20000
30000
40000
50000
60000
CODE
–12
0
10000
20000
30000
40000
50000
60000
CODE
14414-009
–10
14414-006
–10
Figure 10. DNL, IOUTFS = 30 mA
Figure 7. INL, IOUTFS = 30 mA
4
15
2
DNL (LSB)
0
5
0
–2
–4
–6
–8
–5
–10
–12
0
10000
20000
30000
40000
CODE
50000
60000
0
10000
20000
30000
40000
50000
CODE
Figure 11. DNL, IOUTFS = 40 mA
Figure 8. INL, IOUTFS = 40 mA
Rev. A | Page 16 of 136
60000
14414-010
–10
14414-007
INL (LSB)
10
Data Sheet
AD9164
AC PERFORMANCE (NRZ MODE)
0
0
–20
–20
MAGNITUDE (dBm)
–40
–60
–40
–60
1000
2000
3000
4000
5000
FREQUENCY (MHz)
14414-011
0
0
0
0
–20
–20
MAGNITUDE (dBm)
4000
5000
–40
–60
–40
–60
0
1000
2000
3000
4000
5000
FREQUENCY (MHz)
14414-012
–80
Figure 13. Single-Tone Spectrum at fOUT = 70 MHz (FIR85 Enabled)
–40
0
2000
3000
4000
5000
FREQUENCY (MHz)
Figure 16. Single-Tone Spectrum at fOUT = 2000 MHz (FIR85 Enabled)
–40
fDAC = 2500MHz
fDAC = 3000MHz
fDAC = 5000MHz
fDAC = 6000MHz
–50
1000
14414-015
MAGNITUDE (dBm)
3000
Figure 15. Single-Tone Spectrum at fOUT = 2000 MHz
–80
–50
–60
fDAC = 2500MHz
fDAC = 3000MHz
fDAC = 5000MHz
fDAC = 6000MHz
IMD (dBc)
–60
–70
–70
–80
–80
–90
–90
0
500
1000
1500
2000
fOUT (MHz)
2500
3000
14414-013
SFDR (dBc)
2000
FREQUENCY (MHz)
Figure 12. Single-Tone Spectrum at fOUT = 70 MHz
–100
1000
14414-014
–80
–80
Figure 14. SFDR vs. fOUT over fDAC
–100
0
500
1000
1500
2000
fOUT (MHz)
Figure 17. IMD vs. fOUT over fDAC
Rev. A | Page 17 of 136
2500
3000
14414-016
MAGNITUDE (dBm)
IOUTFS = 40 mA, fDAC = 5.0 GSPS, nominal supplies, TA = 25°C, unless otherwise noted.
AD9164
Data Sheet
IOUTFS = 40 mA, fDAC = 5.0 GSPS, nominal supplies, TA = 25°C, unless otherwise noted.
–40
SHUFFLE FALSE
SHUFFLE TRUE
–50
–70
–70
–80
–80
–90
–90
–100
0
500
1000
1500
2000
2500
fOUT (MHz)
–100
0
SHUFFLE FALSE
SHUFFLE TRUE
–60
SFDR (dBc)
–80
–70
–90
500
1000
1500
2000
2500
fOUT (MHz)
–100
0
–50
1500
2000
2500
2500
IOUTFS = 20mA
IOUTFS = 30mA
IOUTFS = 40mA
IMD (dBc)
–60
–70
–70
–80
–80
–90
–90
500
1000
1500
fOUT (MHz)
2000
2500
14414-019
IN-BAND THIRD HARMONIC (dBc)
–40
–60
–100
0
1000
Figure 22. SFDR vs. fOUT over DAC IOUTFS
SHUFFLE FALSE
SHUFFLE TRUE
DIGITAL SCALE = 0dB
DIGITAL SCALE = –6dB
DIGITAL SCALE = –12dB
DIGITAL SCALE = –18dB
500
fOUT (MHz)
Figure 19. SFDR for In-Band Second Harmonic vs. fOUT over Digital Scale
–50
IOUTFS = 20mA
IOUTFS = 30mA
IOUTFS = 40mA
–80
–90
–40
2500
–60
–70
–100
0
2000
–50
14414-018
IN-BAND SECOND HARMONIC (dBc)
–50
1500
Figure 21. IMD vs. fOUT over Digital Scale
–40
DIGITAL SCALE = 0dB
DIGITAL SCALE = –6dB
DIGITAL SCALE = –12dB
DIGITAL SCALE = –18dB
1000
fOUT (MHz)
Figure 18. SFDR vs. fOUT over Digital Scale
–40
500
14414-020
IMD (dBc)
–60
14414-017
SFDR (dBc)
–60
SHUFFLE FALSE
SHUFFLE TRUE
DIGITAL SCALE = 0dB
DIGITAL SCALE = –6dB
DIGITAL SCALE = –12dB
DIGITAL SCALE = –18dB
14414-021
–50
DIGITAL SCALE = 0dB
DIGITAL SCALE = –6dB
DIGITAL SCALE = –12dB
DIGITAL SCALE = –18dB
14414-022
–40
Figure 20. SFDR for In-Band Third Harmonic vs. fOUT over Digital Scale
Rev. A | Page 18 of 136
–100
0
500
1000
1500
2000
fOUT (MHz)
Figure 23. IMD vs. fOUT over DAC IOUTFS
Data Sheet
AD9164
IOUTFS = 40 mA, fDAC = 5.0 GSPS, nominal supplies, TA = 25°C, unless otherwise noted.
–40
–150
TEMPERATURE = –40°C
TEMPERATURE = +25°C
TEMPERATURE = +85°C
–50
W-CDMA NSD (dBm/Hz)
–155
–70
–80
–160
–165
1000
500
1500
2000
2500
fOUT (MHz)
14414-023
–100
0
–175
400
–150
W-CDMA NSD (dBm/Hz)
–155
–165
1400
1600
1800
2000
fDAC = 2500MHz
fDAC = 3000MHz
fDAC = 5000MHz
fDAC = 6000MHz
–165
600
800
1000
1200
1400
1600
1800
2000
–175
400
800
600
1000
1200
1400
1600
1800
14414-225
–170
–170
fOUT (MHz)
2000
fOUT (MHz)
Figure 28. W-CDMA NSD Measured at 10% Offset from fOUT vs. fOUT over fDAC
Figure 25. Single-Tone NSD Measured at 70 MHz vs. fOUT over fDAC
–40
–150
TEMPERATURE = –40°C
TEMPERATURE = +25°C
TEMPERATURE = +85°C
fDAC = 2500MHz
fDAC = 3000MHz
fDAC = 5000MHz
fDAC = 6000MHz
–50
–60
IMD (dBc)
–160
–165
–70
–80
–170
–175
400
–90
600
800
1000
1200
1400
fOUT (MHz)
1600
1800
2000
14414-224
SINGLE-TONE NSD (dBm/Hz)
1200
–160
14414-024
SINGLE-TONE NSD (dBm/Hz)
fDAC = 2500MHz
fDAC = 3000MHz
fDAC = 5000MHz
fDAC = 6000MHz
–160
–155
1000
Figure 27. W-CDMA NSD Measured at 70 MHz vs. fOUT over fDAC
–150
–175
400
800
fOUT (MHz)
Figure 24. SFDR vs. fOUT over Temperature
–155
600
14414-025
–170
–90
Figure 26. Single-Tone NSD Measured at 10% Offset from fOUT vs. fOUT over fDAC
Rev. A | Page 19 of 136
–100
0
500
1000
1500
2000
fOUT (MHz)
Figure 29. IMD vs. fOUT over Temperature
2500
14414-680
SFDR (dBc)
–60
fDAC = 2500MHz
fDAC = 3000MHz
fDAC = 5000MHz
fDAC = 6000MHz
AD9164
Data Sheet
IOUTFS = 40 mA, fDAC = 5.0 GSPS, nominal supplies, TA = 25°C, unless otherwise noted.
–150
–150
W-CDMA NSD (dBm/Hz)
–160
–165
–160
–165
600
800
1000
1200
1400
1600
1800
2000
fOUT (MHz)
–175
400
Figure 30. Single-Tone NSD Measured at 70 MHz vs. fOUT over Temperature
1000
1200
1400
1600
1800
2000
Figure 33. W-CDMA NSD Measured at 70 MHz vs. fOUT over Temperature
–150
TEMPERATURE = –40°C
TEMPERATURE = +25°C
TEMPERATURE = +90°C
TEMPERATURE = –40°C
TEMPERATURE = +25°C
TEMPERATURE = +90°C
–155
W-CDMA NSD (dBm/Hz)
–155
–160
–165
–160
–165
600
800
1000
1200
1400
1600
1800
fOUT (MHz)
2000
–175
400
800
1000
1200
1400
1600
1800
fOUT (MHz)
2000
Figure 34. W-CDMA NSD Measured at 10% Offset from fOUT vs. fOUT over
Temperature
Figure 32. Single-Carrier W-CDMA at 877.5 MHz
14414-032
14414-029
Figure 31. Single-Tone NSD Measured at 10% Offset from fOUT vs. fOUT over
Temperature
600
14414-331
–170
–170
14414-227
SINGLE-TONE NSD (dBm/Hz)
800
fOUT (MHz)
–150
–175
400
600
14414-028
–170
–170
–175
400
TEMPERATURE = –40°C
TEMPERATURE = +25°C
TEMPERATURE = +90°C
–155
–155
14414-027
SINGLE-TONE NSD (dBm/Hz)
TEMPERATURE = –40°C
TEMPERATURE = +25°C
TEMPERATURE = +90°C
Figure 35. Two-Carrier W-CDMA at 875 MHz
Rev. A | Page 20 of 136
Data Sheet
AD9164
IOUTFS = 40 mA, fDAC = 5.0 GSPS, nominal supplies, TA = 25°C, unless otherwise noted.
–60
FIRST ACLR
SECOND ACLR
–65
–70
–70
–75
–80
–85
–85
1200
1400
1600
1800
2000
2200
–90
800
Figure 36. Single-Carrier, W-CDMA Adjacent Channel Leakage Ratio (ACLR) vs.
fOUT (First ACLR, Second ACLR)
1800
2000
2200
THIRD ACLR
FOURTH ACLR
FIFTH ACLR
–70
–70
ACLR (dBc)
–65
–75
–75
–80
–80
–85
–85
1200
1400
1600
1800
2000
2200
fOUT (MHz)
Figure 37. Single-Carrier, W-CDMA ACLR vs. fOUT (Third ACLR, Fourth ACLR,
Fifth ACLR)
–60
1000
1200
1400
1600
1800
SSB PHASE NOISE (dBc/Hz)
–120
–140
2200
Figure 40. Two-Carrier, W-CDMA ACLR vs. fOUT (Third ACLR, Fourth ACLR,
Fifth ACLR)
70MHz
900MHz
1800MHz
3900MHz
CLOCK SOURCE
–80
–100
2000
fOUT (MHz)
–60
70MHz
900MHz
1800MHz
3900MHz
CLOCK SOURCE
–80
–90
800
14414-031
–160
–100
–120
–140
10
100
1k
10k
100k
1M
10M
100M
OFFSET OVER fOUT (Hz)
14414-035
–160
Figure 38. SSB Phase Noise vs. Offset over fOUT, fDAC = 4000 MSPS
(Two Different DAC Clock Sources Used for Best Composite Curve)
–180
10
100
1k
10k
100k
1M
10M
100M
OFFSET OVER fOUT (Hz)
Figure 41. SSB Phase Noise vs. Offset over fOUT, fDAC = 6000 MSPS
Rev. A | Page 21 of 136
14414-036
ACLR (dBc)
1600
–60
–65
–180
1400
Figure 39. Two-Carrier, W-CDMA ACLR vs. fOUT (First ACLR, Second ACLR)
THIRD ACLR
FOURTH ACLR
FIFTH ACLR
1000
1200
fOUT (MHz)
–60
–90
800
1000
14414-034
1000
fOUT (MHz)
SSB PHASE NOISE (dBc/Hz)
–75
–80
–90
800
FIRST ACLR
SECOND ACLR
14414-033
ACLR (dBc)
–65
14414-030
ACLR (dBc)
–60
AD9164
Data Sheet
AC (MIX-MODE)
0
0
–20
–20
MAGNITUDE (dBm)
–40
–60
–40
–60
1000
2000
3000
4000
5000
FREQUENCY (MHz)
14414-038
0
0
0
0
–20
–20
MAGNITUDE (dBm)
4000
5000
–40
–60
–40
–60
–80
1000
2000
3000
4000
5000
FREQUENCY (MHz)
14414-039
0
Figure 43. Single-Tone Spectrum at fOUT = 2350 MHz (FIR85 Enabled)
0
3000
4000
5000
Figure 46. Single-Tone Spectrum at fOUT = 4000 MHz (FIR85 Enabled)
–155
–155
W-CDMA NSD (dBm/Hz)
–150
–165
2000
FREQUENCY (MHz)
–150
–160
1000
14414-042
MAGNITUDE (dBm)
3000
Figure 45. Single-Tone Spectrum at fOUT = 4000 MHz
–80
–160
–165
–170
–170
3000
4000
5000
6000
fOUT (MHz)
7000
14414-040
SINGLE-TONE NSD (dBm/Hz)
2000
FREQUENCY (MHz)
Figure 42. Single-Tone Spectrum at fOUT = 2350 MHz
–175
1000
14414-041
–80
–80
Figure 44. Single-Tone NSD vs. fOUT
–175
3000
4000
5000
6000
fOUT (MHz)
Figure 47. W-CDMA NSD vs. fOUT
Rev. A | Page 22 of 136
7000
14414-599
MAGNITUDE (dBm)
IOUTFS = 40 mA, fDAC = 5.0 GSPS, nominal supplies, TA = 25°C, unless otherwise noted.
Data Sheet
AD9164
IOUTFS = 40 mA, fDAC = 5.0 GSPS, nominal supplies, TA = 25°C, unless otherwise noted.
–40
–50
–50
–60
–60
SFDR (dBc)
–70
–80
3000
4000
SHUFFLE FALSE
SHUFFLE TRUE
5000
6000
7000
8000
fOUT (MHz)
–100
2000
–50
–40
–50
IMD (dBc)
–70
–80
–90
–90
3000
4000
5000
6000
7000
8000
fOUT (MHz)
–100
2000
3000
5000
6000
7000
8000
9000
Figure 52. IMD vs. fOUT over DAC IOUTFS
–40
fDAC = 2500MHz
fDAC = 3000MHz
fDAC = 5000MHz
fDAC = 6000MHz
–50
fDAC = 2500MHz
fDAC = 3000MHz
fDAC = 5000MHz
fDAC = 6000MHz
IMD (dBc)
–60
–70
–70
–80
–80
–90
–90
2000
3000
4000
5000
6000
7000
fOUT (MHz)
8000
9000
14414-046
SFDR (dBc)
4000
fOUT (MHz)
–60
–100
1000
8000
IOUTFS = 20mA
IOUTFS = 30mA
IOUTFS = 40mA
Figure 49. IMD vs. fOUT over Digital Scale
–50
7000
–70
–80
–40
6000
–60
14414-045
IMD (dBc)
–60
–100
2000
5000
Figure 51. SFDR vs. fOUT over DAC IOUTFS
SHUFFLE FALSE
SHUFFLE TRUE
DIGITAL SCALE = 0dB
DIGITAL SCALE = –6dB
DIGITAL SCALE = –12dB
DIGITAL SCALE = –18dB
4000
fOUT (MHz)
Figure 48. SFDR vs. fOUT over Digital Scale
–40
3000
14414-047
–90
DIGITAL SCALE = 0dB
DIGITAL SCALE = –6dB
DIGITAL SCALE = –12dB
DIGITAL SCALE = –18dB
14414-048
–100
2000
–70
–80
14414-044
–90
IOUTFS = 20mA
IOUTFS = 30mA
IOUTFS = 40mA
14414-049
SFDR (dBc)
–40
–100
1000
Figure 50. SFDR vs. fOUT over fDAC
2000
3000
4000
5000
6000
7000
fOUT (MHz)
Figure 53. IMD vs. fOUT over fDAC
Rev. A | Page 23 of 136
8000
AD9164
Data Sheet
14414-051
14414-053
IOUTFS = 40 mA, fDAC = 5.0 GSPS, nominal supplies, TA = 25°C, unless otherwise noted.
Figure 54. Single-Carrier W-CDMA at 1887.5 MHz
–60
FIRST ACLR
SECOND ACLR
–65
–65
–70
–70
ACLR (dBc)
ACLR (dBc)
–60
Figure 57. Four-Carrier W-CDMA at 1980 MHz
–75
FIRST ACLR
SECOND ACLR
–75
–80
–80
–85
–90
2600
2800
3000
3200
3400
3600
3800
fOUT (MHz)
Figure 55. Single-Carrier, W-CDMA ACLR vs. fOUT (First ACLR, Second ACLR)
3000
3200
3400
3600
3800
fOUT (MHz)
Figure 58. Four-Carrier, W-CDMA ACLR vs. fOUT (First ACLR, Second ACLR)
–60
–60
THIRD ACLR
FOURTH ACLR
FIFTH ACL
THIRD ACLR
FOURTH ACLR
FIFTH ACL
–65
–65
–70
–70
ACLR (dBc)
ACLR (dBc)
2800
14414-054
–90
2600
14414-056
–85
–75
–75
–80
–80
–85
–90
2600
2800
3000
3200
fOUT (MHz)
3400
3600
3800
Figure 56. Single-Carrier, W-CDMA ACLR vs. fOUT (Third ACLR, Fourth ACLR,
Fifth ACLR)
2800
3000
3200
fOUT (MHz)
14414-055
–90
2600
3400
3600
3800
14414-057
–85
Figure 59. Four-Carrier, W-CDMA ACLR vs. fOUT (Third ACLR, Fourth ACLR,
Fifth ACLR)
Rev. A | Page 24 of 136
Data Sheet
AD9164
DOCSIS PERFORMANCE (NRZ MODE)
0
0
–10
–10
–20
–20
MAGNITUDE (dBc)
–30
–40
–50
–60
–70
–30
–40
–50
–60
–70
–80
1000
1500
2000
2500
3000
FREQUENCY (MHz)
–90
0
500
1000
1500
2000
2500
3000
FREQUENCY (MHz)
Figure 63. Single Carrier at 70 MHz Output (Shuffle On)
0
–10
–10
–20
–20
–30
–30
MAGNITUDE (dBc)
0
–40
–50
–60
–40
–50
–60
–70
–70
–80
–80
–90
0
500
1000
1500
2000
2500
3000
FREQUENCY (MHz)
–90
14414-059
MAGNITUDE (dBc)
Figure 60. Single Carrier at 70 MHz Output
0
–20
–20
MAGNITUDE (dBc)
–10
–30
–40
–50
–60
–90
FREQUENCY (MHz)
3000
–60
–80
2500
2500
–50
–80
2000
2000
–40
–70
1500
1500
–30
–70
3000
14414-060
MAGNITUDE (dBc)
0
–10
1000
1000
Figure 64. Four Carriers at 70 MHz Output (Shuffle On)
0
500
500
FREQUENCY (MHz)
Figure 61. Four Carriers at 70 MHz Output
0
14414-361
500
14414-362
0
14414-058
–80
–90
–90
0
500
1000
1500
2000
2500
3000
FREQUENCY (MHz)
Figure 65. Eight Carriers at 70 MHz Output (Shuffle On)
Figure 62. Eight Carriers at 70 MHz Output
Rev. A | Page 25 of 136
14414-363
MAGNITUDE (dBc)
IOUTFS = 40 mA, fDAC = 3.076 GSPS, nominal supplies, FIR85 enabled, TA = 25°C, unless otherwise noted.
AD9164
Data Sheet
0
–10
–10
–20
–20
–30
–40
–50
–60
–30
–40
–50
–60
–70
–70
–80
–80
0
500
1000
1500
2000
2500
3000
FREQUENCY (MHz)
–90
–10
–10
–20
–20
MAGNITUDE (dBc)
1500
2000
2500
3000
–30
–40
–50
–60
–30
–40
–50
–60
–70
–80
–80
500
1000
1500
2000
2500
3000
FREQUENCY (MHz)
14414-062
–90
0
–10
–10
–20
–20
MAGNITUDE (dBc)
0
–30
–40
–50
–60
3000
14414-063
FREQUENCY (MHz)
3000
–60
–80
2500
2500
–50
–80
2000
2000
–40
–70
1500
1500
–30
–70
1000
1000
Figure 70. Four Carriers at 950 MHz Output (Shuffle On)
0
500
500
FREQUENCY (MHz)
Figure 67. Four Carriers at 950 MHz Output
0
0
14414-365
MAGNITUDE (dBc)
0
–70
MAGNITUDE (dBc)
1000
Figure 69. Single Carrier at 950 MHz Output (Shuffle On)
0
–90
500
FREQUENCY (MHz)
Figure 66. Single Carrier at 950 MHz Output
–90
0
–90
0
500
1000
1500
2000
2500
3000
FREQUENCY (MHz)
Figure 71. Eight Carriers at 950 MHz Output (Shuffle On)
Figure 68. Eight Carriers at 950 MHz Output
Rev. A | Page 26 of 136
14414-366
–90
14414-364
MAGNITUDE (dBc)
0
14414-061
MAGNITUDE (dBc)
IOUTFS = 40 mA, fDAC = 3.076 GSPS, nominal supplies, FIR85 enabled, TA = 25°C, unless otherwise noted.
Data Sheet
AD9164
IOUTFS = 40 mA, fDAC = 3.076 GSPS, nominal supplies, FIR85 enabled, TA = 25°C, unless otherwise noted.
–40
–60
–70
–80
0
200
400
600
800
1000
1200
1400
fOUT (MHz)
Figure 72. In-Band Second Harmonic vs. fOUT Performance for One DOCSIS Carrier
0
200
400
600
800
1000
1200
1400
fOUT (MHz)
Figure 75. In-Band Third Harmonic vs. fOUT Performance for One DOCSIS Carrier
–80
0
200
400
600
800
1000
1200
1400
Figure 73. In-Band Second Harmonic vs. fOUT Performance for Four DOCSIS
Carriers
–50
–60
–70
–80
–90
0
200
400
600
800
1000
1200
1400
fOUT (MHz)
14414-068
IN-BAND THIRD HARMONIC (dBc)
–70
14414-065
IN-BAND SECOND HARMONIC (dBc)
–60
fOUT (MHz)
Figure 76. In-Band Third Harmonic vs. fOUT Performance for Four DOCSIS
Carriers
–40
IN-BAND THIRD HARMONIC (dBc)
–40
–50
–60
–70
–80
0
200
400
600
800
fOUT (MHz)
1000
1200
1400
Figure 74. In-Band Second Harmonic vs. fOUT Performance for Eight DOCSIS
Carriers
–50
–60
–70
–80
–90
14414-066
IN-BAND SECOND HARMONIC (dBc)
–80
–40
–50
–90
–70
–90
–40
–90
–60
0
200
400
600
800
fOUT (MHz)
1000
1200
1400
14414-069
–90
–50
14414-067
IN-BAND THIRD HARMONIC (dBc)
–50
14414-064
IN-BAND SECOND HARMONIC (dBc)
–40
Figure 77. In-Band Third Harmonic vs. fOUT Performance for Eight DOCSIS
Carriers
Rev. A | Page 27 of 136
AD9164
Data Sheet
IOUTFS = 40 mA, fDAC = 3.076 GSPS, nominal supplies, FIR85 enabled, TA = 25°C, unless otherwise noted.
–40
–60
–70
–80
–60
–70
200
400
600
800
1000
1200
1400
fOUT (MHz)
–90
0
200
–70
–80
0
200
400
600
800
1000
1200
1400
fOUT (MHz)
1200
1400
–60
–70
–90
0
200
–40
800
600
1000
Figure 82. 32-Carrier ACPR vs. fOUT
0
Y-AXIS: FIRST ACPR
Y-AXIS: SECOND ACPR
Y-AXIS: THIRD ACPR
Y-AXIS: FOURTH ACPR
Y-AXIS: FIFTH ACPR
–10
–20
MAGNITUDE (dBc)
–50
400
fOUT (MHz)
Figure 79. Four-Carrier ACPR vs. fOUT
–60
–70
–30
–40
–50
–60
–70
–80
–90
–90
0
200
400
600
800
1000
fOUT (MHz)
1200
1400
0
500
1000
1500
2000
2500
FREQUENCY (MHz)
Figure 83. 194-Carrier, Sinc Enabled, FIR85 Enabled
Figure 80. Eight-Carrier ACPR vs. fOUT
Rev. A | Page 28 of 136
3000
14414-075
–80
14414-072
ACPR (dBc)
1400
–80
14414-071
–90
1200
Y-AXIS: FIRST ACPR
Y-AXIS: SECOND ACPR
Y-AXIS: THIRD ACPR
Y-AXIS: FOURTH ACPR
Y-AXIS: FIFTH ACPR
–50
ACPR (dBc)
ACPR (dBc)
–40
–60
1000
Figure 81. 16-Carrier ACPR vs. fOUT
Y-AXIS: FIRST ACPR
Y-AXIS: SECOND ACPR
Y-AXIS: THIRD ACPR
Y-AXIS: FOURTH ACPR
Y-AXIS: FIFTH ACPR
–50
800
600
fOUT (MHz)
Figure 78. Single-Carrier Adjacent Channel Power Ratio (ACPR) vs. fOUT
–40
400
14414-073
0
14414-074
–80
14414-070
–90
Y-AXIS: FIRST ACPR
Y-AXIS: SECOND ACPR
Y-AXIS: THIRD ACPR
Y-AXIS: FOURTH ACPR
Y-AXIS: FIFTH ACPR
–50
ACPR (dBc)
–50
ACPR (dBc)
–40
Y-AXIS: FIRST ACPR
Y-AXIS: SECOND ACPR
Y-AXIS: THIRD ACPR
Y-AXIS: FOURTH ACPR
Y-AXIS: FIFTH ACPR
Data Sheet
AD9164
IOUTFS = 40 mA, fDAC = 3.076 GSPS, nominal supplies, FIR85 enabled, TA = 25°C, unless otherwise noted.
–40
–25
–35
–50
ACLR IN GAP CHANNEL (dBc)
–55
–65
–75
–85
–95
–105
–60
–70
–80
–90
–125
CENTER 77MHz
RES BW 10kHz
VBW 1.kHz
SPAN 60.0MHz
SWEEP 6.041s (1001pts)
–100
Figure 84. Gap Channel ACLR at 77 MHz
0
200
400
600
800
1000
1200
fGAP (fOUT = fGAP) (MHz)
Figure 85. ACLR in Gap Channel vs. fGAP
Rev. A | Page 29 of 136
1400
14414-077
–115
14414-076
MAGNITUDE (dBm)
–45
AD9164
Data Sheet
TERMINOLOGY
Integral Nonlinearity (INL)
INL is the maximum deviation of the actual analog output from
the ideal output, determined by a straight line drawn from zero
scale to full scale.
therefore, defines how well the interpolation filters work and
the effect of other parasitic coupling paths on the DAC output.
Differential Nonlinearity (DNL)
DNL is the measure of the variation in analog value, normalized
to full scale, associated with a 1 LSB change in digital input code.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the measured output signal
to the rms sum of all other spectral components below the Nyquist
frequency, excluding the first six harmonics and dc. The value
for SNR is expressed in decibels.
Offset Error
Offset error is the deviation of the output current from the ideal
of 0 mA. For OUTPUT+, 0 mA output is expected when all
inputs are set to 0. For OUTPUT−, 0 mA output is expected
when all inputs are set to 1.
Interpolation Filter
If the digital inputs to the DAC are sampled at a multiple rate of
the interpolation rate (fDATA), a digital filter can be constructed that
has a sharp transition band near fDATA/2. Images that typically
appear around the output data rate (fDAC) can be greatly suppressed.
Gain Error
Gain error is the difference between the actual and ideal output
span. The actual span is determined by the difference between
the output when the input is at its minimum code and the
output when the input is at its maximum code.
Adjacent Channel Leakage Ratio (ACLR)
ACLR is the ratio in decibels relative to the carrier (dBc)
between the measured power within a channel relative to its
adjacent channel.
Temperature Drift
Temperature drift is specified as the maximum change from the
ambient (25°C) value to the value at either TMIN or TMAX. For offset
and gain drift, the drift is reported in ppm of full-scale range
(FSR) per degree Celsius. For reference drift, the drift is reported
in ppm per degree Celsius.
Settling Time
Settling time is the time required for the output to reach and
remain within a specified error band around its final value,
measured from the start of the output transition.
Spurious-Free Dynamic Range (SFDR)
SFDR is the difference, in decibels, between the peak amplitude
of the output signal and the peak spurious signal within the dc
to Nyquist frequency of the DAC. Typically, energy in this band
is rejected by the interpolation filters. This specification,
Adjusted DAC Update Rate
The adjusted DAC update rate is the DAC update rate divided
by the smallest interpolating factor. For clarity on DACs with
multiple interpolating factors, the adjusted DAC update rate for
each interpolating factor may be given.
Physical Lane
Physical Lane x refers to SERDINx±.
Logical Lane
Logical Lane x refers to physical lanes after optionally being
remapped by the crossbar block (Register 0x308 to Register 0x30B).
Link Lane
Link Lane x refers to logical lanes considered in the link.
Rev. A | Page 30 of 136
Data Sheet
AD9164
THEORY OF OPERATION
The AD9164 is a 16-bit single RF DAC and digital upconverter
with a SERDES interface. Figure 1 shows a functional block
diagram of the AD9164. Eight high speed serial lanes carry data
at a maximum speed of 12.5 Gbps, and either a 5 GSPS real input
or a 2.5 GSPS complex input data rate to the DAC. Compared to
either LVDS or CMOS interfaces, the SERDES interface
simplifies pin count, board layout, and input clock requirements
to the device.
In addition to the main 48-bit NCO, the AD9164 also offers a
FFH NCO for selected DDS applications. The FFH NCO consists
of 32, 32-bit NCOs, each with its own phase accumulator, a
frequency tuning word (FTW) select register to select one of the
NCOs, and a phase coherent hopping mode; together, these
elements enable phase coherent FFH. With the FTW select
register and the 100 MHz SPI, dwell times as fast as 260 ns can
be achieved.
The clock for the input data is derived from the DAC clock, or
device clock (required by the JESD204B specification). This
device clock is sourced with a high fidelity direct external DAC
sampling clock. The performance of the DAC can be optimized by
using on-chip adjustments to the clock input accessible through the
SPI port. The device can be configured to operate in one-lane, twolane, three-lane, four-lane, six-lane, or eight-lane modes,
depending on the required input data rate.
The AD9164 DAC core provides a fully differential current
output with a nominal full-scale current of 38.76 mA. The full-scale
output current, IOUTFS, is user adjustable from 8 mA to 38.76 mA,
typically. The differential current outputs are complementary.
The DAC uses the patented quad-switch architecture, which
enables DAC decoder options to extend the output frequency
range into the second and third Nyquist zones with Mix-Mode,
return to zero (RZ) mode, and 2× NRZ mode (with FIR85
enabled). Mix-Mode can be used to access 1.5 GHz to around
5 GHz. In the interpolation modes, the output can range from
0 Hz to 6 GHz in 2× NRZ mode using the NCO to shift a signal
of up to 1.8 GHz instantaneous bandwidth to the desired fOUT.
The digital datapath of the AD9164 offers a bypass (1×) mode
and several interpolation modes (2×, 3×, 4×, 6×, 8×, 12×, 16×,
and 24×) through either an initial half-band (2×) or third-band
(3×) filter with programmable 80% or 90% bandwidth, and
three subsequent half-band filters (all 90%) with a maximum
DAC sample rate of 6 GSPS. An inverse sinc filter is provided to
compensate for sinc related roll-off. An additional half-band
filter, FIR85, takes advantage of the quad-switch architecture to
interpolate on the falling edge of the clock, and effectively double
the DAC update rate in 2× NRZ mode. A 48-bit programmable
modulus NCO is provided to enable digital frequency shifts of
signals with near infinite precision. The NCO can be operated
alone in NCO only mode or with digital data from the SERDES
interface and digital datapath. The 100 MHz speed of the SPI
write interface enables rapid updating of the frequency tuning
word of the NCO.
The AD9164 is capable of multichip synchronization that can both
synchronize multiple DACs and establish a constant and deterministic latency (latency locking) path for the DACs. The latency for
each of the DACs remains constant to within several DAC clock
cycles from link establishment to link establishment. An external
alignment (SYSREF±) signal makes the AD9164 Subclass 1
compliant. Several modes of SYSREF± signal handling are
available for use in the system.
An SPI configures the various functional blocks and monitors
their statuses. The various functional blocks and the data interface
must be set up in a specific sequence for proper operation (see the
Start-Up Sequence section). Simple SPI initialization routines set
up the JESD204B link and are included in the evaluation board
package. This data sheet describes the various blocks of the
AD9164 in greater detail. Descriptions of the JESD204B
interface, control parameters, and various registers to set up and
monitor the device are provided. The recommended start-up
routine reliably sets up the data link.
Rev. A | Page 31 of 136
AD9164
Data Sheet
SERIAL PORT OPERATION
The serial port is a flexible, synchronous serial communications
port that allows easy interfacing with many industry-standard
microcontrollers and microprocessors. The serial input/output
(I/O) is compatible with most synchronous transfer formats,
including both the Motorola SPI and Intel® SSR protocols. The
interface allows read/write access to all registers that configure
the AD9164. MSB first or LSB first transfer formats are supported.
The serial port interface can be configured as a 4-wire interface
or a 3-wire interface in which the input and output share a singlepin I/O (SDIO).
CS F12
The serial clock pin synchronizes data to and from the device
and runs the internal state machines. The maximum frequency
of SCLK is 100 MHz. All data input is registered on the rising
edge of SCLK. All data is driven out on the falling edge of SCLK.
SPI
PORT
14414-078
SCLK H10
Figure 86. Serial Port Interface Pins (169-Ball CSP_BGA)
There are two phases to a communication cycle with the AD9164.
Phase 1 is the instruction cycle (the writing of an instruction
byte into the device), coincident with the first 16 SCLK rising
edges. The instruction word provides the serial port controller
with information regarding the data transfer cycle, Phase 2 of
the communication cycle. The Phase 1 instruction word defines
whether the upcoming data transfer is a read or write, along with
the starting register address for the following data transfer.
A logic high on the CS pin followed by a logic low resets the
serial port timing to the initial state of the instruction cycle.
From this state, the next 16 rising SCLK edges represent the
instruction bits of the current I/O operation.
The remaining SCLK edges are for Phase 2 of the communication
cycle. Phase 2 is the actual data transfer between the device and
the system controller. Phase 2 of the communication cycle is a
transfer of one or more data bytes. Eight × N SCLK cycles are
needed to transfer N bytes during the transfer cycle. Registers
change immediately upon writing to the last bit of each transfer
byte, except for the FTW and NCO phase offsets, which change
only when the frequency tuning word FTW_LOAD_REQ bit is set.
DATA FORMAT
The instruction byte contains the information shown in Table 14.
Table 14. Serial Port Instruction Word
I15 (MSB)
R/W
SERIAL PORT PIN DESCRIPTIONS
Serial Clock (SCLK)
SDO G11
SDIO G10
A14 to A0, Bit I14 to Bit I0 of the instruction word, determine
the register that is accessed during the data transfer portion of
the communication cycle. For multibyte transfers, A[14:0] is the
starting address. The remaining register addresses are generated
by the device based on the address increment bit. If the address
increment bits are set high (Register 0x000, Bit 5 and Bit 2), multibyte SPI writes start on A[14:0] and increment by 1 every eight
bits sent/received. If the address increment bits are set to 0, the
address decrements by 1 every eight bits.
I[14:0]
A[14:0]
Chip Select (CS)
An active low input starts and gates a communication cycle.
CS allows more than one device to be used on the same serial
communications lines. The SDIO pin goes to a high impedance
state when this input is high. During the communication cycle,
the chip select must stay low.
Serial Data I/O (SDIO)
This pin is a bidirectional data line. In 4-wire mode, this pin
acts as the data input and SDO acts as the data output.
SERIAL PORT OPTIONS
The serial port can support both MSB first and LSB first data
formats. This functionality is controlled by the LSB first bit
(Register 0x000, Bit 6 and Bit 1). The default is MSB first (LSB
bit = 0).
When the LSB first bits = 0 (MSB first), the instruction and data
bits must be written from MSB to LSB. R/W is followed by
A[14:0] as the instruction word, and D[7:0] is the data-word.
When the LSB first bits = 1 (LSB first), the opposite is true.
A[0:14] is followed by R/W, which is subsequently followed by
D[0:7].
The serial port supports a 3-wire or 4-wire interface. When the
SDO active bits = 1 (Register 0x000, Bit 4 and Bit 3), a 4-wire
interface with a separate input pin (SDIO) and output pin (SDO) is
used. When the SDO active bits = 0, the SDO pin is unused and
the SDIO pin is used for both the input and the output.
R/W, Bit 15 of the instruction word, determines whether a read
or a write data transfer occurs after the instruction word write.
Logic 1 indicates a read operation, and Logic 0 indicates a write
operation.
Rev. A | Page 32 of 136
Data Sheet
AD9164
To prevent confusion and to ensure consistency between devices,
the chip tests the first nibble following the address phase, ignoring
the second nibble. This test is completed independently from the
LSB first bits and ensures that there are extra clock cycles following
the soft reset bits (Register 0x000, Bit 0 and Bit 7). This test of
the first nibble only applies when writing to Register 0x000.
INSTRUCTION CYCLE
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CS
SDIO
A0
A1
A2
A12 A13 A14 R/W D00 D10 D20
Figure 88. Serial Register Interface Timing, LSB First, Register 0x000, Bit 5 and
Bit 2 = 1
CS
SCLK
tDV
SDIO
DATA BIT n
DATA BIT n – 1
Figure 89. Timing Diagram for Serial Port Register Read
DATA TRANSFER CYCLE
CS
R/W A14 A13
A3
A2 A1
A0 D7N D6N D5N
14414-079
SCLK
SDIO
D30 D20 D10 D00
Figure 87. Serial Register Interface Timing, MSB First, Register 0x000, Bit 5
and Bit 2 = 0
tS
tH
CS
tPWH
tPWL
SDIO
tDH
INSTRUCTION BIT 15
INSTRUCTION BIT 14
INSTRUCTION BIT 0
Figure 90. Timing Diagram for Serial Port Register Write
Rev. A | Page 33 of 136
14414-082
SCLK
tDS
D4N D5N D6N D7N
14414-080
SCLK
14414-081
Multibyte data transfers can be performed as well by holding
the CS pin low for multiple data transfer cycles (eight SCLKs)
after the first data transfer word following the instruction cycle.
The first eight SCLKs following the instruction cycle read from
or write to the register provided in the instruction cycle. For
each additional eight SCLK cycles, the address is either incremented or decremented and the read/write occurs on the new
register. The direction of the address can be set using ADDRINC or
ADDRINC_M (Register 0x000, Bit 5 and Bit 2). When ADDRINC
or ADDRINC_M is 1, the multicycle addresses are incremented.
When ADDRINC or ADDRINC_M is 0, the addresses are decremented. A new write cycle can always be initiated by bringing
CS high and then low again.
AD9164
Data Sheet
JESD204B SERIAL DATA INTERFACE
JESD204B OVERVIEW
The various combinations of JESD204B parameters that are
supported depend solely on the number of lanes. Thus, a
unique set of parameters can be determined by selecting the
lane count to be used. In addition, the interpolation rate and
number of lanes can be used to define the rest of the configuration needed to set up the AD9164. The interpolation rate and
the number of lanes are selected in Register 0x110.
The AD9164 has eight JESD204B data ports that receive data.
The eight JESD204B ports can be configured as part of a single
JESD204B link that uses a single system reference (SYSREF±) and
device clock (CLK±).
The JESD204B serial interface hardware consists of three layers:
the physical layer, the data link layer, and the transport layer.
These sections of the hardware are described in subsequent
sections, including information for configuring every aspect of
the interface. Figure 91 shows the communication layers
implemented in the AD9164 serial data interface to recover the
clock and deserialize, descramble, and deframe the data before it
is sent to the digital signal processing section of the device.
The AD9164 has a single DAC output; however, for the purposes
of the complex signal processing on chip, the converter count is
defined as M = 2 whenever interpolation is used.
For a particular application, the number of converters to use
(M) and the DataRate variable are known. The LaneRate
variable and number of lanes (L) can be traded off as follows:
DataRate = (DACRate)/(InterpolationFactor)
LaneRate = (20 × DataRate × M)/L
The physical layer establishes a reliable channel between the
transmitter (Tx) and the receiver (Rx), the data link layer is
responsible for unpacking the data into octets and descrambling
the data. The transport layer receives the descrambled
JESD204B frames and converts them to DAC samples.
where LaneRate must be between 750 Mbps and 12.5 Gbps.
Achieving and recovering synchronization of the lanes is very
important. To simplify the interface to the transmitter, the
AD9164 designate a master synchronization signal for each
JESD204B link. The SYNCOUT± pin is used as the master signal
for all lanes. If any lane in a link loses synchronization, a
resynchronization request is sent to the transmitter via the
synchronization signal of the link. The transmitter stops sending
data and instead sends synchronization characters to all lanes in
that link until resynchronization is achieved.
A number of JESD204B parameters (L, F, K, M, N, NP, S, HD)
define how the data is packed and tell the device how to turn
the serial data into samples. These parameters are defined in
detail in the Transport Layer section. The AD9164 also has a
descrambling option (see the Descrambler section for more
information).
SYNCOUT±
PHYSICAL
LAYER
SERDIN7±
TRANSPORT
LAYER
QBD/
DESCRAMBLER
FRAME TO
SAMPLES
I DATA[15:0]
DESERIALIZER
TO DAC
DSP BLOCK
Q DATA[15:0]
DESERIALIZER
14414-083
SERDIN0±
DATA LINK
LAYER
SYSREF±
Figure 91. Functional Block Diagram of Serial Link Receiver
Table 15. Single-Link JESD204B Operating Modes
Parameter
L (Lane Count)
M (Converter Count)
F (Octets per Frame per Lane)
S (Samples per Converter per Frame)
1
1
2
4
1
2
2
2
2
1
Rev. A | Page 34 of 136
3
3
2
4
3
4
4
2
1
1
Number of Lanes (L)
6
8
6
8
2
1 (real), 2 (complex)
2
1
3
4 (real), 2 (complex)
Data Sheet
AD9164
Table 16. Data Structure per Lane for JESD204B Operating Modes1
JESD204B Parameters
L = 8, M = 1, F = 1, S = 4
L = 8, M = 2, F = 1, S = 2
L = 6, M = 2, F = 2, S = 3
L = 4, M = 2, F = 1, S = 1
L = 3, M = 2, F = 4, S = 3
L = 2, M = 2, F = 2, S = 1
L = 1, M = 2, F = 4, S = 1
1
Lane No.
Lane 0
Lane 1
Lane 2
Lane 3
Lane 4
Lane 5
Lane 6
Lane 7
Lane 0
Lane 1
Lane 2
Lane 3
Lane 4
Lane 5
Lane 6
Lane 7
Lane 0
Lane 1
Lane 2
Lane 3
Lane 4
Lane 5
Lane 0
Lane 1
Lane 2
Lane 3
Lane 0
Lane 1
Lane 2
Lane 0
Lane 1
Lane 0
Frame 0
M0S0[15:8]
M0S0[7:0]
M0S1[15:8]
M0S1[7:0]
M0S2[15:8]
M0S2[7:0]
M0S3[15:8]
M0S3[7:0]
M0S0[15:8]
M0S0[7:0]
M0S1[15:8]
M0S1[7:0]
M1S0[15:8]
M1S0[7:0]
M1S1[15:8]
M1S1[7:0]
M0S0[15:8]
M0S1[15:8]
M0S2[15:8]
M1S0[15:8]
M1S1[15:8]
M1S2[15:8]
M0S0[15:8]
M0S0[7:0]
M1S0[15:8]
M1S0[7:0]
M0S0[15:8]
M0S2[15:8]
M1S1[15:8]
M0S0[15:8]
M1S0[15:8]
M0S0[15:8]
Frame 1
Frame 2
Frame 3
M0S1[15:8]
M1S0[15:8]
M1S2[15:8]
M0S1[7:0]
M1S0[7:0]
M1S2[7:0]
M1S0[15:8]
M1S0[7:0]
M0S0[7:0]
M0S1[7:0]
M0S2[7:0]
M1S0[7:0]
M1S1[7:0]
M1S2[7:0]
M0S0[7:0]
M0S2[7:0]
M1S1[7:0]
M0S0[7:0]
M1S0[7:0]
M0S0[7:0]
Mx is the converter number and Sy is the sample number. For example, M0S0 means Converter 0, Sample 0. Blank cells are not applicable.
PHYSICAL LAYER
Interface Power-Up and Input Termination
The physical layer of the JESD204B interface, hereafter referred
to as the deserializer, has eight identical channels. Each channel
consists of the terminators, an equalizer, a clock and data recovery
(CDR) circuit, and the 1:40 demux function (see Figure 92).
Before using the JESD204B interface, it must be powered up by
setting Register 0x200, Bit 0 = 0. In addition, each physical lane
(PHY) that is not being used (SERDINx±) must be powered
down. To do so, set the corresponding Bit x for Physical Lane x in
Register 0x201 to 0 if the physical lane is being used, and to 1 if it is
not being used.
DESERIALIZER
SERDINx±
TERMINATION
EQUALIZER
CDR
1:40
14414-084
SPI
CONTROL
FROM SERDES PLL
Figure 92. Deserializer Block Diagram
JESD204B data is input to the AD9164 via the SERDINx± 1.2 V
differential input pins as per the JESD204B specification.
The AD9164 autocalibrates the input termination to 50 Ω.
Before running the termination calibration, Register 0x2A7 and
Register 0x2AE must be written as described in Table 17 to
guarantee proper calibration. The termination calibration begins
when Register 0x2A7, Bit 0 and Register 0x2AE, Bit 0 transition
from low to high. Register 0x2A7 controls autocalibration for
PHY 0, PHY 1, PHY 6, and PHY 7. Register 0x2AE controls
autocalibration for PHY 2, PHY 3, PHY 4, and PHY 5.
Rev. A | Page 35 of 136
AD9164
Data Sheet
The PHY termination autocalibration routine is as shown in
Table 17.
Table 17. PHY Termination Autocalibration Routine
Address
0x2A7
Value
0x01
0x2AE
0x01
Description
Autotune PHY 0, PHY 1, PHY 6, and
PHY 7 terminations
Autotune PHY 2, PHY 3, PHY 4, and
PHY 5 terminations
Clock Relationships
The following clocks rates are used throughout the rest of the
JESD204B section. The relationship between any of the clocks
can be derived from the following equations:
DataRate = (DACRate)/(InterpolationFactor)
LaneRate = (20 × DataRate × M)/L
ByteRate = LaneRate/10
The input termination voltage of the DAC is sourced externally
via the VTT_1P2 pins (Ball M3 and Ball M13 on the 8 mm ×
8 mm package, or Ball K3 and Ball K11 on the 11 mm × 11 mm
package). Set VTT, the termination voltage, by connecting it to
VDD_1P2. It is recommended that the JESD204B inputs be accoupled to the JESD204B transmit device using 100 nF capacitors.
This relationship comes from 8-bit/10-bit encoding, where each
byte is represented by 10 bits.
The calibration code of the termination can be read from
Bits[3:0] in Register 0x2AC (PHY 0, PHY 1, PHY 6, PHY 7)
and Register 0x2B3 (PHY 2, PHY 3, PHY 4, PHY 5). If needed,
the termination values can be adjusted or set using several
registers. The TERM_BLKx_CTRLREG1 registers (Register 0x2A8
and Register 0x2AF), can override the autocalibrated value. When
set to 0xXXX0XXXX, the termination block autocalibrates,
which is the normal, default setting. When set to 0xXXX1XXXX,
the autocalibration value is overwritten with the value in Bits[3:1]
of Register 0x2A8 and Register 0x2AF. Individual offsets from the
autocalibration value for each lane can be programmed in Bits[3:0]
of Register 0x2BB to Register 0x2C2. The value is a signed magnitude, with Bit 3 as the sign bit. The total range of the termination
resistor value is about 94 Ω to 120 Ω, with approximately 3.5%
increments across the range (for example, smaller steps at the
bottom of the range than at the top).
where F is defined as octets per frame per lane.
Receiver Eye Mask
The AD9164 complies with the JESD204B specification
regarding the receiver eye mask and is capable of capturing data
that complies with this mask. Figure 93 shows the receiver eye
mask normalized to the data rate interval with a 600 mV VTT
swing. See the JESD204B specification for more information
regarding the eye mask and permitted receiver eye opening.
LV-OIF-11G-SR RECEIVER EYE MASK
The processing clock is used for a quad-byte decoder.
FrameRate = ByteRate/F
PCLK Factor = FrameRate/PCLK Rate = 4/F
where:
M is the JESD204B parameter for converters per link.
L is the JESD204B parameter for lanes per link.
F is the JESD204B parameter for octets per frame per lane.
SERDES PLL
Functional Overview of the SERDES PLL
The independent SERDES PLL uses integer N techniques to
achieve clock synthesis. The entire SERDES PLL is integrated
on chip, including the VCO and the loop filter. The SERDES
PLL VCO operates over the range of 6 GHz to 12.5 GHz.
In the SERDES PLL, a VCO divider block divides the VCO
clock by 2 to generate a 3 GHz to 6.25 GHz quadrature clock for
the deserializer cores. This clock is the input to the clock and
data recovery block that is described in the Clock and Data
Recovery section.
The reference clock to the SERDES PLL is always running at a
frequency, fREF, that is equal to 1/40 of the lane rate (PCLK rate).
This clock is divided by a DivFactor value (set by SERDES_PLL_
DIV_FACTOR) to deliver a clock to the phase frequency detector
(PFD) block that is between 35 MHz and 80 MHz. Table 18
includes the respective SERDES_PLL_DIV_FACTOR register
settings for each of the desired PLL_REF_CLK_RATE options
available.
Table 18. SERDES PLL Divider Settings
55
0
–55
–525
0
0.35
0.5
0.65
1.00
TIME (UI)
14414-085
AMPLITUDE (mV)
525
PCLK Rate = ByteRate/4
Lane Rate
(Gbps)
0.750 to 1.5625
1.5 to 3.125
3 to 6.25
6 to 12.5
Figure 93. Receiver Eye Mask for 600 mV VTT Swing
Rev. A | Page 36 of 136
PLL_REF_CLK_RATE,
Register 0x084, Bits[5:4]
0b01 = 2×
0b00 = 1×
0b00 = 1×
0b00 = 1×
SERDES_PLL_DIV_FACTOR
Register 0x289, Bits[1:0]
0b10 = ÷1
0b10 = ÷1
0b01 = ÷2
0b00 = ÷4
Data Sheet
AD9164
Register 0x280 controls the synthesizer enable and recalibration.
To enable the SERDES PLL, first set the PLL divider register (see
Table 18). Then enable the SERDES PLL by writing Register 0x280,
Bit 0 = 1. If a recalibration is needed, write Register 0x280, Bit 2 =
0b1 and then reset the bit to 0b0. The rising edge of the bit causes a
recalibration to begin.
Confirm that the SERDES PLL is working by reading
Register 0x281. If Register 0x281, Bit 0 = 1, the SERDES PLL
has locked. If Register 0x281, Bit 3 = 1, the SERDES PLL was
successfully calibrated. If Register 0x281, Bit 4 or Bit 5 is high, the
PLL reaches the lower or upper end of its calibration band and
must be recalibrated by writing 0 and then 1 to Register 0x280,
Bit 2.
Clock and Data Recovery
The deserializer is equipped with a CDR circuit. Instead of
recovering the clock from the JESD204B serial lanes, the CDR
recovers the clocks from the SERDES PLL. The 3 GHz to
6.25 GHz output from the SERDES PLL, shown in Figure 94, is
the input to the CDR.
A CDR sampling mode must be selected to generate the lane
rate clock inside the device. If the desired lane rate is greater
than 6.25 GHz, half rate CDR operation must be used. If the
desired lane rate is less than 6.25 GHz, disable half rate operation.
If the lane rate is less than 3 GHz, disable full rate and enable 2×
oversampling to recover the appropriate lane rate clock. Table 19
lists the CDR sampling settings that must be set depending on
the LaneRate value.
Table 19. CDR Operating Modes
After configuring the CDR circuit, reset it and then release the
reset by writing 1 and then 0 to Register 0x206, Bit 0.
Power-Down Unused PHYs
Note that any unused and enabled lanes consume extra power
unnecessarily. Each lane that is not being used (SERDINx±)
must be powered off by writing a 1 to the corresponding bit of
PHY_PD (Register 0x201).
Equalization
To compensate for signal integrity distortions for each PHY
channel due to PCB trace length and impedance, the AD9164
employs an easy to use, low power equalizer on each JESD204B
channel. The AD9164 equalizers can compensate for insertion
losses far greater than required by the JESD204B specification.
The equalizers have two modes of operation that are
determined by the EQ_POWER_MODE register setting in
Register 0x268, Bits[7:6]. In low power mode (Register 0x268,
Bits[7:6] = 2b’01) and operating at the maximum lane rate of
12.5 Gbps, the equalizer can compensate for up to 11.5 dB of
insertion loss. In normal mode (Register 0x268, Bits[7:6] =
2b’00), the equalizer can compensate for up to 17.2 dB of insertion
loss. This performance is shown in Figure 95 as an overlay to the
JESD204B specification for insertion loss. Figure 95 shows the
equalization performance at 12.5 Gbps, near the maximum baud
rate for the AD9164.
SPI_DIVISION_RATE,
Register 0x230,
Bits[2:1]
10b (divide by 4)
01b (divide by 2)
00b (no divide)
00b (no divide)
SPI_ENHALFRATE
Register 0x230, Bit 5
0 (full rate)
0 (full rate)
0 (full rate)
1 (half rate)
DIVIDE (N)
20
40
80
160
MODE
HALF RATE
FULL RATE, NO DIV
FULL RATE, DIV 2
FULL RATE, DIV 4
INTERPOLATION
JESD LANES
REG 0x110
DAC CLOCK
(5GHz)
÷4
PCLK
GENERATOR
CDR OVERSAMP
REG 0x289
PLL REF CLOCK
VALID RANGE
35MHz TO 80MHz
÷4, ÷2,
OR ÷1
ENABLE HALF RATE
DIVISION RATE
REG 0x230
SAMPLE CLOCK
I, Q TO CDR
VALID RANGE
3GHz TO 6.25GHz
CP
LF
PLL_REF_CLK_RATE
1×, 2×, 4×
REG 0x084
÷2
CDR
÷N
÷8
÷6 TO ÷127,
DEFAULT: 10
Figure 94. SERDES PLL Synthesizer Block Diagram Including VCO Divider Block
Rev. A | Page 37 of 136
JESD LANE CLOCK
(SAME RATE AS PCLK)
14414-086
LaneRate
(Gbps)
0.750 to 1.5625
1.5 to 3.125
3 to 6.25
6 to 12.5
The CDR circuit synchronizes the phase used to sample the data on
each serial lane independently. This independent phase adjustment
per serial interface ensures accurate data sampling and eases the
implementation of multiple serial interfaces on a PCB.
AD9164
Data Sheet
JESD204B SPEC ALLOWED
CHANNEL LOSS
EXAMPLE OF
JESD204B
COMPLIANT
CHANNEL
4
INSERTION LOSS (dB)
10
EXAMPLE OF
AD9164
COMPATIBLE
CHANNEL (LOW
POWER MODE)
AD9164 ALLOWED
CHANNEL LOSS
(LOW POWER MODE)
12
AD9164 ALLOWED
CHANNEL LOSS
(NORMAL MODE)
14
16
20
22
6.250
14414-087
24
3.125
9.375
FREQUENCY (GHz)
Figure 95. Insertion Loss Allowed
–5
–15
–20
–25
STRIPLINE = 6"
STRIPLINE = 10"
STRIPLINE = 15"
STRIPLINE = 20"
STRIPLINE = 25"
STRIPLINE = 30"
–40
0
1
2
3
4
5
6" MICROSTRIP
10" MICROSTRIP
15" MICROSTRIP
20" MICROSTRIP
25" MICROSTRIP
30" MICROSTRIP
–30
–35
–40
0
1
2
3
4
5
6
7
8
9
FREQUENCY (GHz)
10
Figure 97. Insertion Loss of 50 Ω Microstrips on FR4
6
7
8
9
FREQUENCY (GHz)
10
14414-088
ATTENUATION (dB)
–10
–35
–25
The AD9164 decode 8-bit/10-bit control characters, allowing
marking of the start and end of the frame and alignment
between serial lanes. Each AD9164 serial interface link can issue
a synchronization request by setting its SYNCOUT± signal low.
The synchronization protocol follows Section 4.9 of the JESD204B
standard. When a stream of four consecutive /K/ symbols is
received, the AD9164 deactivates the synchronization request
by setting the SYNCOUT± signal high at the next internal
LMFC rising edge. Then, AD9164 waits for the transmitter to
issue an initial lane alignment sequence (ILAS). During the
ILAS, all lanes are aligned using the /A/ to /R/ character transition
as described in the JESD204B Serial Link Establishment section.
Elastic buffers hold early arriving lane data until the alignment
character of the latest lane arrives. At this point, the buffers for
all lanes are released and all lanes are aligned (see Figure 99).
0
–30
–20
The AD9164 can operate as a single-link high speed JESD204B
serial data interface. All eight lanes of the JESD204B interface
handle link layer communications such as code group synchronization (CGS), frame alignment, and frame synchronization.
EXAMPLE OF
AD9164
COMPATIBLE
CHANNEL
(NORMAL MODE)
18
–15
The data link layer of the AD9164 JESD204B interface accepts
the deserialized data from the PHYs and deframes, and
descrambles them so that data octets are presented to the transport
layer to be put into DAC samples. The architecture of the data
link layer is shown in Figure 98. The data link layer consists of a
synchronization FIFO for each lane, a crossbar switch, a deframer,
and a descrambler.
6
8
–10
DATA LINK LAYER
0
2
–5
14414-089
Low power mode is recommended if the insertion loss of the
JESD204B PCB channels is less than that of the most lossy
supported channel for low power mode (shown in Figure 95). If
the insertion loss is greater than that, but still less than that of
the most lossy supported channel for normal mode (shown in
Figure 95), use normal mode. At 12.5 Gbps operation, the
equalizer in normal mode consumes about 4 mW more power
per lane used than in low power equalizer mode. Note that either
mode can be used in conjunction with transmitter preemphasis
to ensure functionality and/or optimize for power.
0
ATTENUATION (dB)
Figure 96 and Figure 97 are provided as points of reference for
hardware designers and show the insertion loss for various
lengths of well laid out stripline and microstrip transmission
lines, respectively. See the Hardware Considerations section for
specific layout recommendations for the JESD204B channel.
Figure 96. Insertion Loss of 50 Ω Striplines on FR4
Rev. A | Page 38 of 136
Data Sheet
AD9164
DATA LINK LAYER
SYNCOUTx±
QUAD-BYTE
DEFRAMER
QBD
LANE 0 DESERIALIZED
AND DESCRAMBLED DATA
SERDIN0±
FIFO
CROSSBAR
SWITCH
LANE 7 DESERIALIZED
AND DESCRAMBLED DATA
SYSREF±
SERDIN7±
FIFO
LANE 7 OCTETS
SYSTEM CLOCK
PHASE DETECT
14414-090
LANE 7 DATA CLOCK
LANE 0 OCTETS
DESCRAMBLE
8-BIT/10-BIT DECODE
LANE 0 DATA CLOCK
PCLK
SPI CONTROL
Figure 98. Data Link Layer Block Diagram
L RECEIVE LANES
(EARLIEST ARRIVAL) K K K R D D
D D A R Q C
L RECEIVE LANES
(LATEST ARRIVAL) K K K K K K K R D D
C
D D A R Q C
D D A R D D
C
D D A R D D
0 CHARACTER ELASTIC BUFFER DELAY OF LATEST ARRIVAL
4 CHARACTER ELASTIC BUFFER DELAY OF EARLIEST ARRIVAL
L ALIGNED
RECEIVE LANES K K K K K K K R D D
D D A R Q C
D D A R D D
14414-091
K = K28.5 CODE GROUP SYNCHRONIZATION COMMA CHARACTER
A = K28.3 LANE ALIGNMENT SYMBOL
F = K28.7 FRAME ALIGNMENT SYMBOL
R = K28.0 START OF MULTIFRAME
Q = K28.4 START OF LINK CONFIGURATION DATA
C = JESD204x LINK CONFIGURATION PARAMETERS
D = Dx.y DATA SYMBOL
C
Figure 99. Lane Alignment During ILAS
JESD204B Serial Link Establishment
A brief summary of the high speed serial link establishment
process for Subclass 1 is provided. See Section 5.3.3 of the
JESD204B specifications document for complete details.
Step 1: Code Group Synchronization
Each receiver must locate /K/ (K28.5) characters in its input
data stream. After four consecutive /K/ characters are detected
on all link lanes, the receiver block deasserts the SYNCOUT±
signal to the transmitter block at the receiver LMFC edge.
The transmitter captures the change in the SYNCOUT± signal
and at a future transmitter LMFC rising edge starts the ILAS.
Step 2: Initial Lane Alignment Sequence
The main purposes of this phase are to align all the lanes of the
link and to verify the parameters of the link.
Before the link is established, write each of the link parameters
to the receiver device to designate how data is sent to the
receiver block.
The ILAS consists of four or more multiframes. The last character
of each multiframe is a multiframe alignment character, /A/.
The first, third, and fourth multiframes are populated with
predetermined data values. Note that Section 8.2 of the JESD204B
specifications document describes the data ramp that is expected
during ILAS. The AD9164 does not require this ramp. The
deframer uses the final /A/ of each lane to align the ends of the
multiframes within the receiver. The second multiframe contains
an /R/ (K.28.0), /Q/ (K.28.4), and then data corresponding to
the link parameters. Additional multiframes can be added to
the ILAS if needed by the receiver. By default, the AD9164 uses
four multiframes in the ILAS (this can be changed in Register
0x478). If using Subclass 1, exactly four multiframes must be used.
After the last /A/ character of the last ILAS, multiframe data
begins streaming. The receiver adjusts the position of the /A/
character such that it aligns with the internal LMFC of the
receiver at this point.
Rev. A | Page 39 of 136
AD9164
Data Sheet
Step 3: Data Streaming
Crossbar Switch
In this phase, data is streamed from the transmitter block to the
receiver block.
Register 0x308 to Register 0x30B allow arbitrary mapping of
physical lanes (SERDINx±) to logical lanes used by the SERDES
deframers.
Optionally, data can be scrambled. Scrambling does not start
until the very first octet following the ILAS.
The receiver block processes and monitors the data it receives
for errors, including the following:
•
•
•
•
•
Bad running disparity (8-bit/10-bit error)
Not in table (8-bit/10-bit error)
Unexpected control character
Bad ILAS
Interlane skew error (through character replacement)
If any of these errors exist, they are reported back to the
transmitter in one of the following ways (see the JESD204B
Error Monitoring section for details):
•
•
•
SYNCOUT± signal assertion: resynchronization
(SYNCOUT± signal pulled low) is requested at each error
for the last two errors. For the first three errors, an optional
resynchronization request can be asserted when the error
counter reaches a set error threshold.
For the first three errors, each multiframe with an error in
it causes a small pulse on SYNCOUT±.
Errors can optionally trigger an interrupt request (IRQ)
event, which can be sent to the transmitter.
For more information about the various test modes for
verifying the link integrity, see the JESD204B Test Modes
section.
Table 20. Crossbar Registers
Address
0x308
0x308
0x309
0x309
0x30A
0x30A
0x30B
0x30B
Bits
[2:0]
[5:3]
[2:0]
[5:3]
[2:0]
[5:3]
[2:0]
[5:3]
Logical Lane
SRC_LANE0
SRC_LANE1
SRC_LANE2
SRC_LANE3
SRC_LANE4
SRC_LANE5
SRC_LANE6
SRC_LANE7
Write each SRC_LANEy with the number (x) of the desired
physical lane (SERDINx±) from which to obtain data. By
default, all logical lanes use the corresponding physical lane as
their data source. For example, by default, SRC_LANE0 = 0;
therefore, Logical Lane 0 obtains data from Physical Lane 0
(SERDIN0±). To use SERDIN4± as the source for Logical Lane 0
instead, the user must write SRC_LANE0 = 4.
Lane Inversion
Register 0x334 allows inversion of desired logical lanes, which
can be used to ease routing of the SERDINx± signals. For each
Logical Lane x, set Bit x of Register 0x334 to 1 to invert it.
Deframer
Lane First In/First Out (FIFO)
The FIFOs in front of the crossbar switch and deframer synchronize the samples sent on the high speed serial data interface
with the deframer clock by adjusting the phase of the incoming
data. The FIFO absorbs timing variations between the data
source and the deframer; this allows up to two PCLK cycles of
drift from the transmitter. The FIFO_STATUS_REG_0 register
and FIFO_STATUS_REG_1 register (Register 0x30C and
Register 0x30D, respectively) can be monitored to identify
whether the FIFOs are full or empty.
Lane FIFO IRQ
An aggregate lane FIFO error bit is also available as an IRQ
event. Use Register 0x020, Bit 2 to enable the FIFO error bit,
and then use Register 0x024, Bit 2 to read back its status and
reset the IRQ signal. See the Interrupt Request Operation
section for more information.
The AD9164 consists of one quad-byte deframer (QBD). The
deframer accepts the 8-bit/10-bit encoded data from the
deserializer (via the crossbar switch), decodes it, and descrambles it
into JESD204B frames before passing it to the transport layer to be
converted to DAC samples. The deframer processes four symbols
(or octets) per processing clock (PCLK) cycle.
The deframer uses the JESD204B parameters that the user has
programmed into the register map to identify how the data is
packed, and unpacks it. The JESD204B parameters are
described in detail in the Transport Layer section; many of the
parameters are also needed in the transport layer to convert
JESD204B frames into samples.
Descrambler
The AD9164 provides an optional descrambler block using a
self synchronous descrambler with the following polynomial: 1 +
x14 + x15.
Enabling data scrambling reduces spectral peaks that are
produced when the same data octets repeat from frame to
frame. It also makes the spectrum data independent so that
possible frequency selective effects on the electrical interface do
not cause data dependent errors. Descrambling of the data is
enabled by setting the SCR bit (Register 0x453, Bit 7) to 1.
Rev. A | Page 40 of 136
Data Sheet
AD9164
Syncing LMFC Signals
SYSREF+
50Ω
50Ω
SYSREF–
SYSREF± Signal
The SYSREF± signal is a differential source synchronous input that
synchronizes the LMFC signals in both the transmitter and receiver
in a JESD204B Subclass 1 system to achieve deterministic latency.
The SYSREF± signal is a rising edge sensitive signal that is
sampled by the device clock rising edge. It is best practice that the
device clock and SYSREF± signals be generated by the same
source, such as the HMC7044 clock generator, so that the phase
alignment between the signals is fixed. When designing for
optimum deterministic latency operation, consider the timing
distribution skew of the SYSREF± signal in a multipoint link
system (multichip).
The AD9164 supports a periodic SYSREF± signal. The periodicity
can be continuous, strobed, or gapped periodic. The SYSREF±
signal can always be dc-coupled (with a common-mode voltage
of 0 V to 1.25 V). When dc-coupled, a small amount of commonmode current (<500 µA) is drawn from the SYSREF± pins. See
Figure 100 and Figure 101 for the SYSREF± internal circuit.
To avoid this common-mode current draw, use a 50% duty cycle
periodic SYSREF± signal with ac coupling capacitors. If ac-coupled,
the ac coupling capacitors combine with the resistors shown in
Figure 100 or Figure 101 to make a high-pass filter with an RC
time constant of τ = RC. Select C such that τ > 4/SYSREF±
frequency. In addition, the edge rate must be sufficiently fast to
meet the SYSREF± vs. DAC clock keep out window (KOW)
requirements.
It is possible to use ac-coupled mode without meeting the
frequency to time constant constraints (τ = RC and τ > 4/SYSREF±
frequency) by using SYSREF± hysteresis (Register 0x088 and
Register 0x089). However, using hystereis increases the DAC
clock KOW (Table 6 does not apply) by an amount depending
on the SYSREF± frequency, level of hysteresis, capacitor choice,
and edge rate.
100Ω
200Ω
19kΩ
3kΩ
Figure 101. SYSREF± Input Circuit for the 11 mm × 11 mm 169-Ball BGA
Sync Processing Modes Overview
The AD9164 supports several LMFC sync processing modes.
These modes are one shot, continuous, and monitor modes. All
sync processing modes perform a phase check to confirm that the
LMFC is phase aligned to an alignment edge. In Subclass 1, the
SYSREF± rising edge acts as the alignment edge; in Subclass 0, an
internal processing clock acts as the alignment edge.
The SYSREF± signal is sampled by a divide by 4 version of the
DAC clock. After SYSREF± is sampled, the phase of the (DAC
clock) ÷4 used to sample SYSREF± is stored in Register 0x037,
Bits[7:0] and Register 0x038, Bits[3:0] as a thermometer code. This
offset can be used by the SERDES data transmitter (for example,
FPGA) to align multiple DACs by accounting for this clock offset
when transmitting data. The sync modes are described below. See
the Sync Procedure section for details on the procedure for
syncing the LMFC signals.
One Shot Sync Mode (SYNCMODE = Register 0x03A,
Bits[1:0] = 0b10)
In one shot sync mode, a phase check occurs on only the first
alignment edge that is received after the sync machine is armed.
After the phase is aligned on the first edge, the AD9164 transitions
to monitor mode. Though an LMFC synchronization occurs only
once, the SYSREF± signal can still be continuous. In this case,
the phase is monitored and reported, but no clock phase
adjustment occurs.
Continuous Sync Mode (SYNCMODE = Register 0x03A,
Bits[1:0] = 0b01)
Continuous mode must be used in Subclass 1 only with a periodic
SYSREF± signal. In continuous mode, a phase check/alignment
occurs on every alignment edge.
Monitor Sync Mode (SYNCMODE = Register 0x03A,
Bits[1:0]) = 0b00)
14414-092
SYSREF–
19kΩ
Continuous mode differs from one shot mode in two ways.
First, no SPI cycle is required to arm the device; the alignment
edge seen after continuous mode is enabled results in a phase
check. Second, a phase check occurs on every alignment edge in
continuous mode.
200Ω
SYSREF+
3kΩ
14414-147
The first step in guaranteeing synchronization across links and
devices begins with syncing the LMFC signals. In Subclass 0,
the LMFC signal is synchronized to an internal processing
clock. In Subclass 1, LMFC signals are synchronized to an
external SYSREF± signal.
Figure 100. SYSREF± Input Circuit for the 8 mm × 8 mm 165-Ball BGA
In monitor mode, the user can monitor the phase error in real time.
Use this sync mode with a periodic SYSREF± signal. The phase is
monitored and reported, but no clock phase adjustment occurs.
Rev. A | Page 41 of 136
AD9164
Data Sheet
When an alignment request (SYSREF± edge) occurs, snapshots
of the last phase error are placed into readable registers for
reference (Register 0x037 and Register 0x038, Bits[3:0]), and the
IRQ_SYSREF_JITTER interrupt is set, if appropriate.
Sync Procedure
The procedure for enabling the sync is as follows:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Set up the DAC; the SERDES PLL locks it, and enables the
CDR (see the Start-Up Sequence section).
Set Register 0x039 (SYSREF± jitter window). A minimum
of four DAC clock cycles is recommended. See Table 22 for
settings.
Optionally, read back the SYSREF± count to check whether
the SYSREF± pulses are being received.
a. Set Register 0x036 = 0. Writing anything to
SYSREF_COUNT resets the count.
b. Set Register 0x034 = 0. Writing anything to
SYNC_LMFC_STAT0 saves the data for readback and
registers the count.
c. Read SYSREF_COUNT from the value from
Register 0x036.
Perform a one shot sync.
a. Set Register 0x03A = 0x00. Clear one shot mode if
already enabled.
b. Set Register 0x03A = 0x02. Enable one shot sync
mode. The state machine enters monitor mode after a
sync occurs.
Optionally, read back the sync SYNC_LMFC_STATx
registers to verify that sync completed correctly.
a. Set Register 0x034 = 0. Register 0x034 must be written
to read the value.
b. Read Register 0x035 and Register 0x034 to find the
value of SYNC_LMFC_STATx. It is recommended to
set SYNC_LMFC_STATx to 0 but it can be set to 4, or
a LMFC period in DAC clocks − 4, due to jitter.
Optionally, read back the sync SYSREF_PHASEx register
to identify which phase of the divide by 4 was used to
sample SYSREF±. Read Register 0x038 and Register 0x037
as thermometer code. The MSBs of Register 0x037,
Bits[7:4] normally show the thermometer code value.
Turn the link on (Register 0x300, Bit 0 = 1).
Read back Register 0x302 (dynamic link latency).
Repeat the reestablishment of the link several times (Step 1
to Step 7) and note the dynamic link latency values. Based
on the values, program the LMFC delay (Register 0x304)
and the LMFC variable (Register 0x306), and then restart
the link.
Table 21. Sync Processing Modes
Sync Processing
Mode
No synchronization
One shot
Continuous
Table 22. SYSREF± Jitter Window Tolerance
SYSREF± Jitter Window
Tolerance (DAC Clock Cycles)
±½
±4
±8
±12
±16
+20
+24
+28
1
SYSREF_JITTER_WINDOW
(Register 0x039, Bits[5:0])1
0x00
0x04
0x08
0x0C
0x10
0x14
0x18
0x1C
The two least significant digits are ignored because the SYSREF± signal is
sampled with a divide by 4 version of the DAC clock. As a result, the jitter
window is set by this divide by 4 clock rather than the DAC clock. It is
recommended that at least a four-DAC clock SYSREF± jitter window be
chosen.
Deterministic Latency
JESD204B systems contain various clock domains distributed
throughout its system. Data traversing from one clock domain
to a different clock domain can lead to ambiguous delays in the
JESD204B link. These ambiguities lead to nonrepeatable latencies
across the link from power cycle to power cycle with each new
link establishment. Section 6 of the JESD204B specification
addresses the issue of deterministic latency with mechanisms
defined as Subclass 1 and Subclass 2.
The AD9164 support JESD204B Subclass 0 and Subclass 1
operation, but not Subclass 2. Write the subclass to Register 0x458,
Bits[7:5].
Subclass 0
This mode gives deterministic latency to within 32 DAC clock
cycles. It does not require any signal on the SYSREF± pins,
which can be left disconnected.
Subclass 0 still requires that all lanes arrive within the same LMFC
cycle and the dual DACs must be synchronized to each other.
Subclass 1
This mode gives deterministic latency and allows the link to be
synced to within four DAC clock periods. It requires an external
SYSREF± signal that is accurately phase aligned to the DAC clock.
Deterministic Latency Requirements
Several key factors are required for achieving deterministic
latency in a JESD204B Subclass 1 system.
•
•
•
SYNC_MODE (Register 0x03A, Bits[1:0])
0b00
0b10
0b01
Rev. A | Page 42 of 136
SYSREF± signal distribution skew within the system must
be less than the desired uncertainty.
SYSREF± setup and hold time requirements must be met
for each device in the system.
The total latency variation across all lanes, links, and
devices must be ≤10 PCLK periods, which includes both
variable delays and the variation in fixed delays from lane
to lane, link to link, and device to device in the system.
Data Sheet
AD9164
LINK DELAY = DELAYFIXED + DELAYVARIABLE
LOGIC DEVICE
(JESD204B Tx)
CHANNEL
JESD204B Rx
DSP
DAC
POWER CYCLE
VARIANCE
LMFC
ILAS
DATA
ALIGNED DATA
AT Rx OUTPUT
ILAS
DATA
FIXED DELAY
VARIABLE
DELAY
14414-095
DATA AT
Tx INPUT
Figure 102. JESD204B Link Delay = Fixed Delay + Variable Delay
Link Delay
Setting LMFCDel appropriately ensures that all the corresponding
data samples arrive in the same LMFC period. Then LMFCVar
is written into the receive buffer delay (RBD) to absorb all link
delay variation. This write ensures that all data samples have
arrived before reading. By setting these to fixed values across
runs and devices, deterministic latency is achieved.
The link delay of a JESD204B system is the sum of the fixed and
variable delays from the transmitter, channel, and receiver as
shown in Figure 102.
For proper functioning, all lanes on a link must be read during
the same LMFC period. Section 6.1 of the JESD204B specification states that the LMFC period must be larger than the maximum
link delay. For the AD9164, this is not necessarily the case;
instead, the AD9164 use a local LMFC for each link (LMFCRx)
that can be delayed from the SYSREF± aligned LMFC. Because
the LMFC is periodic, this delay can account for any amount of
fixed delay. As a result, the LMFC period must only be larger
than the variation in the link delays, and the AD9164 can achieve
proper performance with a smaller total latency. Figure 103 and
Figure 104 show a case where the link delay is greater than an
LMFC period. Note that it can be accommodated by delaying
LMFCRx.
The RBD described in the JESD204B specification takes values
from one frame clock cycle to K frame clock cycles, and the
RBD of the AD9164 takes values from 0 PCLK cycle to
10 PCLK cycles. As a result, up to 10 PCLK cycles of total delay
variation can be absorbed. LMFCVar and LMFCDel are both in
PCLK cycles. The PCLK factor, or number of frame clock cycles
per PCLK cycle, is equal to 4/F. For more information on this
relationship, see the Clock Relationships section.
Two examples follow that show how to determine LMFCVar
and LMFCDel. After they are calculated, write LMFCDel into
Register 0x304 for all devices in the system, and write LMFCVar
to Register 0x306 for all devices in the system.
POWER CYCLE
VARIANCE
Link Delay Setup Example, with Known Delays
LMFC
ILAS
DATA
EARLY ARRIVING
LMFC REFERENCE
All the known system delays can be used to calculate LMFCVar
and LMFCDel.
14414-093
ALIGNED DATA
LATE ARRIVING
LMFC REFERENCE
The example shown in Figure 105 is demonstrated in the
following steps. Note that this example is in Subclass 1 to
achieve deterministic latency, which has a PCLK factor (4/F) of
two frame clock cycles per PCLK cycle, and uses K = 32
(frames/multiframe). Because PCBFixed << PCLK Period,
PCBFixed is negligible in this example and not included in the
calculations.
Figure 103. Link Delay > LMFC Period Example
POWER CYCLE
VARIANCE
LMFC
ALIGNED DATA
ILAS
DATA
1.
LMFC_DELAY
LMFC REFERENCE FOR ALL POWER CYCLES
FRAME CLOCK
Figure 104. LMFC_DELAY_x to Compensate for Link Delay > LMFC
14414-094
LMFCRX
2.
The method to select the LMFCDel (Register 0x304) and
LMFCVar (Register 0x306) variables is described in the Link
Delay Setup Example, with Known Delays section.
Rev. A | Page 43 of 136
Find the receiver delays using Table 7.
RxFixed = 12 PCLK cycles
RxVar = 2 PCLK cycles
Find the transmitter delays. The equivalent table in the
example JESD204B core (implemented on a GTH or GTX
gigabit transceiver on a Virtex-6 FPGA) states that the
delay is 56 ± 2 byte clock cycles.
AD9164
4.
5.
Because the PCLK Rate = ByteRate/4 as described in the
Clock Relationships section, the transmitter delays in
PCLK cycles are calculated as follows:
TxFixed = 54/4 = 13.5 PCLK cycles
TxVar = 4/4 = 1 PCLK cycle
Calculate MinDelayLane as follows:
MinDelayLane = floor(RxFixed + TxFixed + PCBFixed)
= floor(12 + 13.5 + 0)
= floor(25.5)
MinDelayLane = 25
Calculate MaxDelayLane as follows:
MaxDelayLane = ceiling(RxFixed + RxVar + TxFixed +
TxVar + PCBFixed))
= ceiling(12 + 2 + 13.5 + 1 + 0)
6.
7.
8.
= ceiling(28.5)
MaxDelayLane = 29
Calculate LMFCVar as follows:
LMFCVar = (MaxDelay + 1) − (MinDelay − 1)
= (29 + 1) − (25 − 1) = 30 − 24
LMFCVar = 6 PCLK cycles
Calculate LMFCDel as follows:
LMFCDel = (MinDelay − 1) % (K/PClockFactor)
= ((30 − 1)) % (32/2)
= 29 % 16
LMFCDel = 13 PCLK cycles
Write LMFCDel to Register 0x304 for all devices in the
system. Write LMFCVar to Register 0x306 for all devices in
the system.
LMFC
PCLK
FRAME CLOCK
DATA AT Tx FRAMER
ALIGNED LANE DATA
AT Rx DEFRAMER OUTPUT
ILAS
DATA
ILAS
Tx VAR
DELAY
Rx VAR
DELAY
DATA
PCB FIXED
DELAY
LMFCRX
LMFC DELAY = 26 FRAME CLOCK CYCLES
TOTAL FIXED LATENCY = 30 PCLK CYCLES
Figure 105. LMFC Delay Calculation Example
Rev. A | Page 44 of 136
TOTAL VARIABLE
LATENCY = 4
PCLK CYCLES
14414-096
3.
Data Sheet
Data Sheet
AD9164
Link Delay Setup Example, Without Known Delay
•
•
If the system delays are not known, the AD9164 can read back
the link latency between LMFCRX for each link and the SYSREF±
aligned LMFC. This information is then used to calculate
LMFCVar and LMFCDel.
The example shown in Figure 107 is demonstrated in the
following steps. Note that this example is in Subclass 1 to
achieve deterministic latency, which has a PCLK Factor
(FrameRate ÷ PCLK Rate) of 4 and uses K = 32; therefore PCLK
cycles per multiframe = 8.
Figure 107 shows how DYN_LINK_LATENCY_0 (Register 0x302)
provides a readback showing the delay (in PCLK cycles)
between LMFCRX and the transition from ILAS to the first data
sample. By repeatedly power cycling and taking this measurement,
the minimum and maximum delays across power cycles can be
determined and used to calculate LMFCVar and LMFCDel.
1.
2.
In Figure 107, for Link A, Link B, and Link C, the system
containing the AD9164 (including the transmitter) is power
cycled and configured 20 times. The AD9164 is configured as
described in the Sync Procedure section. Because the purpose
of this exercise is to determine LMFCDel and LMFCVar, the
LMFCDel value is programmed to 0 and the DYN_LINK_
LATENCY_0 value is read from Register 0x302. The variation
in the link latency over the 20 runs is shown in Figure 107,
described as follows:
3.
4.
Link A gives readbacks of 6, 7, 0, and 1. Note that the set of
recorded delay values rolls over the edge of a multiframe at
the boundary of K/ PCLK Factor = 8. Add the number of
PCLK cycles per multiframe = 8 to the readback values of 0
and 1 because they rolled over the edge of the multiframe.
Delay values range from 6 to 9.
5.
Calculate the minimum of all delay measurements across
all power cycles, links, and devices as follows:
MinDelay = min(all Delay values) = 4
Calculate the maximum of all delay measurements across
all power cycles, links, and devices as follows:
MaxDelay = max(all Delay values) = 9
Calculate the total delay variation (with guard band) across
all power cycles, links, and devices as follows:
LMFCVar = (MaxDelay + 1) − (MinDelay − 1)
= (9 + 1) − (4 − 1) = 10 − 3 = 7 PCLK cycles
Calculate the minimum delay in PCLK cycles (with guard
band) across all power cycles, links, and devices as follows:
LMFCDel
= (MinDelay − 1) % (K/PCLK Factor)
= (4 − 1) % 32/4
= 3 % 8 = 3 PCLK cycles
Write LMFCDel to Register 0x304 for all devices in the system.
Write LMFCVar to Register 0x306 for all devices in the system.
SYSREF±
LMFCRX
ILAS
ALIGNED DATA
DATA
14414-097
DYN_LINK_LATENCY
Figure 106. DYN_LINK_LATENCY_x Illustration
LMFC
PCLK
FRAME CLOCK
DYN_LINK_LATENCY_CNT
0
1
2
ALIGNED DATA (LINK A)
ALIGNED DATA (LINK B)
ALIGNED DATA (LINK C)
3
4
5
6
7
0
1
2
3
ILAS
4
5
6
7
DATA
ILAS
DATA
ILAS
DATA
LMFCRX
DETERMINISTICALLY
DELAYED DATA
ILAS
LMFC_DELAY = 6
(FRAME CLOCK CYCLES)
DATA
LMFC_VAR = 7
(PCLK CYCLES)
Figure 107. Multilink Synchronization Settings, Derived Method Example
Rev. A | Page 45 of 136
14414-098
•
Link B gives delay values from 5 to 7.
Link C gives delay values from 4 to 7.
AD9164
Data Sheet
TRANSPORT LAYER
TRANSPORT LAYER
(QBD)
LANE 0 OCTETS
DAC A_I0[15:0]
DELAY
BUFFER 0
F2S_0
DAC A_Q0[15:0]
LANE 3 OCTETS
PCLK_0
SPI CONTROL
LANE 4 OCTETS
DAC B_I0[15:0]
DELAY
BUFFER 1
PCLK_0
TO
PCLK_1
FIFO
F2S_1
DAC B_Q0[15:0]
14414-099
LANE 7 OCTETS
PCLK_1
SPI CONTROL
Figure 108. Transport Layer Block Diagram
The transport layer receives the descrambled JESD204B frames
and converts them to DAC samples based on the programmed
JESD204B parameters shown in Table 23. The device parameters
are defined in Table 24.
Table 23. JESD204B Transport Layer Parameters
Parameter
F
K
L
M
S
Description
Number of octets per frame per lane: 1, 2, or 4
Number of frames per multiframe: K = 32
Number of lanes per converter device (per link), as
follows: 4 or 8
Number of converters per device (per link), as follows:
1 or 2 (1 is used for real data mode; 2 is used for
complex data modes)
Number of samples per converter, per frame: 1 or 2
Table 24. JESD204B Device Parameters
Parameter
CF
CS
HD
N
Nʹ (or NP)
Description
Number of control words per device clock per link.
Not supported, must be 0.
Number of control bits per conversion sample. Not
supported, must be 0.
High density user data format. Used when samples
must be split across lanes. Set to1 always, even when
F does not equal 1. Otherwise, a link configuration
error triggers and the IRQ_ILAS flag is set.
Converter resolution = 16.
Total number of bits per sample = 16.
Certain combinations of these parameters are supported by the
AD9164. See Table 27 for a list of supported interpolation rates
and the number of lanes that is supported for each rate. Table 27
lists the JESD204B parameters for each of the interpolation and
number of lanes configuration, and gives an example lane rate
for a 5 GHz DAC clock. Table 26 lists JESD204B parameters
that have fixed values. A value of yes in Table 25 means the
interpolation rate is supported for the number of lanes. A blank cell
means it is not supported.
Table 25. Interpolation Rates and Number of Lanes
Interpolation
1×
2×
3×
4×
6×
8×
12×
16×
24×
1
8
Yes1
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
6
4
3
2
1
Yes1
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes1
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
These modes restrict the maximum DAC clock rate to 5 GHz.
Table 26. JESD204B Parameters with Fixed Values
Parameter
K
N
NP
CF
HD
CS
Rev. A | Page 46 of 136
Value
32
16
16
0
1
0
Data Sheet
AD9164
Table 27. JESD204B Parameters for Interpolation Rate and Number of Lanes
Interpolation
Rate
1
2
2
3
3
4
4
4
4
6
6
6
6
8
8
8
8
8
12
12
12
12
12
16
16
16
16
16
16
24
24
24
24
24
24
1
No. of
Lanes
8
6
8
6
8
3
4
6
8
3
4
6
8
2
3
4
6
8
2
3
4
6
8
1
2
3
4
6
8
1
2
3
4
6
8
M
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
F
1
2
1
2
1
4
1
2
1
4
1
2
1
2
4
1
2
1
2
4
1
2
1
4
2
4
1
2
1
4
2
4
1
2
1
S
4
3
2
3
2
3
1
3
2
3
1
3
2
1
3
1
3
2
1
3
1
3
2
1
1
3
1
3
2
1
1
3
1
3
2
PCLK Period
(DAC Clocks)
16
12
16
18
24
12
16
24
32
18
24
36
48
16
24
32
48
64
24
36
48
72
96
16
32
48
64
96
128
24
48
72
96
144
192
LMFC Period
(DAC Clocks)
128
192
128
288
192
384
128
384
256
576
192
576
384
256
768
256
768
512
384
1152
384
1152
768
512
512
1536
512
1536
1024
768
768
2304
768
2304
1536
Maximum lane rate is 12.5 GHz. These modes must be run with the DAC rate below 3.75 GHz.
Rev. A | Page 47 of 136
Lane Rate at 5 GHz DAC Clock
(GHz)
12.5
16.661
12.5
11.11
8.33
16.661
12.5
8.33
6.25
11.11
8.33
5.55
4.16
12.5
8.33
6.25
4.16
3.12
8.33
5.55
4.16
2.77
2.08
12.5
6.25
4.16
3.12
2.08
1.56
8.33
4.16
2.77
2.08
1.38
1.04
AD9164
Data Sheet
Configuration Parameters
JESD204B TEST MODES
The AD9164 modes refer to the link configuration parameters
for L, K, M, N, NP, S, and F. Table 28 provides the description
and addresses for these settings.
PHY PRBS Testing
Table 28. Configuration Parameters
JESD204B
Setting
L−1
F−1
Description
Number of lanes minus 1.
M−1
Number of ((octets per frame) per
lane) minus 1.
Number of frames per multiframe −
1.
Number of converters minus 1.
N−1
Converter bit resolution minus 1.
NP − 1
Bit packing per sample minus 1.
S−1
Number of ((samples per
converter) per frame) minus 1.
High density format. Set to 1 if F =
1. Leave at 0 if F ≠ 1.
Device ID. Match the device ID
sent by the transmitter.
Bank ID. Match the bank ID sent by
the transmitter.
Lane ID for Lane 0. Match the Lane
ID sent by the transmitter on
Logical Lane 0.
JESD204x version. Match the
version sent by the transmitter
(0x0 = JESD204A, 0x1 = JESD204B).
K−1
HD
DID
BID
LID0
JESDV
Address
Register 0x453,
Bits[4:0]
Register 0x454,
Bits[7:0]
Register 0x455,
Bits[4:0]
Register 0x456,
Bits[7:0]
Register 0x457,
Bits[4:0]
Register 0x458,
Bits[4:0]
Register 0x459,
Bits[4:0]
Register 0x45A,
Bit 7
Register 0x450,
Bits[7:0]
Register 0x451,
Bits[7:0]
Register 0x452,
Bits[4:0]
The JESD204B receiver on the AD9164 includes a PRBS pattern
checker on the back end of its physical layer. This functionality
enables bit error rate (BER) testing of each physical lane of the
JESD204B link. The PHY PRBS pattern checker does not
require that the JESD204B link be established. It can synchronize
with a PRBS7, PRBS15, or PRBS31 data pattern. PRBS pattern
verification can be done on multiple lanes at once. The error
counts for failing lanes are reported for one JESD204B lane at a
time. The process for performing PRBS testing on the AD9164
is as follows:
1.
2.
3.
4.
5.
6.
Register 0x459,
Bits[7:5]
7.
8.
Data Flow Through the JESD204B Receiver
The link configuration parameters determine how the serial bits
on the JESD204B receiver interface are deframed and passed on
to the DACs as data samples.
9.
Deskewing and Enabling Logical Lanes
After proper configuration, the logical lanes are automatically
deskewed. All logical lanes are enabled or not based on the lane
number setting in Register 0x110, Bits[7:4]. The physical lanes
are all powered up by default.
To disable power to physical lanes that are not being used, set Bit x
in Register 0x201 to 1 to disable Physical Lane x, and keep it at 0
to enable it.
Start sending a PRBS7, PRBS15, or PRBS31 pattern from
the JESD204B transmitter.
Select and write the appropriate PRBS pattern to
Register 0x316, Bits[3:2], as shown in Table 29.
Enable the PHY test for all lanes being tested by writing to
PHY_TEST_EN (Register 0x315). Each bit of Register 0x315
enables the PRBS test for the corresponding lane. For example,
writing a 1 to Bit 0 enables the PRBS test for Physical Lane 0.
Toggle PHY_TEST_RESET (Register 0x316, Bit 0) from 0
to 1 then back to 0.
Set PHY_PRBS_TEST_THRESHOLD_xBITS (Bits[23:0],
Register 0x319 to Register 0x317) as desired.
Write a 0 and then a 1 to PHY_TEST_START (Register 0x316,
Bit 1). The rising edge of PHY_TEST_START starts the test.
a. (Optional) In some cases, it may be necessary to
repeat Step 4 at this point. Toggle PHY_TEST_RESET
(Register 0x316, Bit 0) from 0 to 1, then back to 0.
Wait 500 ms.
Stop the test by writing PHY_TEST_START
(Register 0x316, Bit 1) = 0.
Read the PRBS test results.
a. Each bit of PHY_PRBS_PASS (Register 0x31D)
corresponds to one SERDES lane (0 = fail, 1 = pass).
b. The number of PRBS errors seen on each failing lane
can be read by writing the lane number to check (0 to 7)
in PHY_SRC_ERR_CNT (Register 0x316, Bits[6:4]) and
reading the PHY_PRBS_ERR_COUNT (Register 0x31C
to Register 0x31A). The maximum error count is 224 − 1.
If all bits of Register 0x31C to Register 0x31A are high,
the maximum error count on the selected lane is
exceeded.
Table 29. PHY PRBS Pattern Selection
PHY_PRBS_PAT_SEL Setting
(Register 0x316, Bits[3:2])
0b00 (default)
0b01
0b10
Rev. A | Page 48 of 136
PRBS Pattern
PRBS7
PRBS15
PRBS31
Data Sheet
AD9164
Transport Layer Testing
The JESD204B receiver in the AD9164 supports the short
transport layer (STPL) test as described in the JESD204B
standard. This test can be used to verify the data mapping
between the JESD204B transmitter and receiver. To perform
this test, this function must be implemented in the logic device
and enabled there. Before running the test on the receiver side,
the link must be established and running without errors.
The STPL test ensures that each sample from each converter is
mapped appropriately according to the number of converters
(M) and the number of samples per converter (S). As specified
in the JESD204B standard, the converter manufacturer specifies
what test samples are transmitted. Each sample must have a
unique value. For example, if M = 2 and S = 2, four unique
samples are transmitted repeatedly until the test is stopped. The
expected sample must be programmed into the device and the
expected sample is compared to the received sample one sample
at a time until all are tested. The process for performing this test
on the AD9164 is described as follows:
1.
2.
3.
Synchronize the JESD204B link.
Enable the STPL test at the JESD204B Tx.
Depending on JESD204B case, there may be up to two
DACs, and each frame may contain up to four DAC
samples. Configure the SHORT_TPL_REF_SP_MSB bits
(Register 0x32E) and SHORT_TPL_REF_SP_LSB bits
4.
5.
6.
7.
8.
9.
(Register 0x32D) to match one of the samples for one
converter within one frame.
Set SHORT_TPL_SP_SEL (Register 0x32C, Bits[7:4]) to
select the sample within one frame for the selected
converter according to Table 30.
Set SHORT_TPL_TEST_EN (Register 0x32C, Bit 0) to 1.
Set SHORT_TPL_TEST_RESET (Register 0x32C, Bit 1) to
1, then back to 0.
Wait for the desired time. The desired time is calculated as
1/(sample rate × BER). For example, given a bit error rate
of BER = 1 × 10−10 and a sample rate = 1 GSPS, the desired
time = 10 sec. Then, set SHORT_TPL_TEST_EN to 0.
Read the test result at SHORT_TPL_FAIL (Register 0x32F,
Bit 0).
Choose another sample for the same or another converter
to continue with the test, until all samples for both
converters from one frame are verified. (Note that the
converter count is M = 2 for all interpolator modes on the
AD9164 to enable complex signal processing.)
Consult Table 30 for a guide to the test sample alignment. Note
that the sample order for 1×, eight-lane mode has Sample 1 and
Sample 2 swapped. Also, the STPL test for the three-lane and
six-lane options is not functional and always fails.
Table 30. Short TPL Test Samples Assignment1
JESD204x Mode
1× Eight-Lane (L = 8, M = 1, F = 1, S = 4)
Required Samples from JESD204x Tx
Send four samples: M0S0, M0S1, M0S2,
M0S3, and repeat
2× Eight-Lane (L = 8, M = 2, F = 1, S = 2)
3× Eight-Lane (L = 8, M = 2, F = 1, S = 2)
4× Eight-Lane (L = 8, M = 2, F = 1, S = 2)
6× Eight-Lane (L = 8, M = 2, F = 1, S = 2)
8× Eight-Lane (L = 8, M = 2, F = 1, S = 2)
12× Eight-Lane e (L = 8, M = 2, F = 1, S = 2)
16× Eight-Lane (L = 8, M = 2, F = 1, S = 2)
24× Eight-Lane (L = 8, M = 2, F = 1, S = 2)
2× Six-Lane (L = 6, M = 2, F = 2, S = 3)
3× Six-Lane (L = 6, M = 2, F = 2, S = 3)
4× Six-Lane (L = 6, M = 2, F = 2, S = 3)
6× Six-Lane (L = 6, M = 2, F = 2, S = 3)
8× Six-Lane (L = 6, M = 2, F = 2, S = 3)
12× Six-Lane (L = 6, M = 2, F = 2, S = 3)
16× Six-Lane (L = 6, M = 2, F = 2, S = 3)
24× Six-Lane (L = 6, M = 2, F = 2, S = 3)
4× Six-Lane (L = 3, M = 2, F = 4, S = 3)
6× Three-Lane (L = 3, M = 2, F = 4, S = 3)
8× Three-Lane (L = 3, M = 2, F = 4, S = 3)
12× Three-Lane (L = 3, M = 2, F = 4, S = 3)
16× Three-Lane (L = 3, M = 2, F = 4, S = 3)
24× Three-Lane (L = 3, M = 2, F = 4, S = 3)
Send four samples: M0S0, M0S1, M1S0,
M1S1, and repeat
Send six samples: M0S0, M0S1, M0S2,
M1S0, M1S1, M1S2, and repeat
Rev. A | Page 49 of 136
Samples Assignment
SP0: M0S0, SP4: M0S0, SP8: M0S0, SP12: M0S0
SP1: M0S2, SP5: M0S2, SP9: M0S2, SP13: M0S2
SP2: M0S1, SP6: M0S1, SP10: M0S1, SP14: M0S1
SP3: M0S3, SP7: M0S3, SP11: M0S3, SP15: M0S3
SP0: M0S0, SP4: M0S0, SP8: M0S0, SP12: M0S0
SP1: M1S0, SP5: M1S0, SP9: M1S0, SP13: M1S0
SP2: M0S1, SP6: M0S1, SP10: M0S1, SP14: M0S1
SP3: M1S1, SP7: M1S1, SP11: M1S1, SP15: M1S1
Test hardware is not functional; STPL always fails
AD9164
JESD204x Mode
4× Four-Lane (L = 4, M = 2, F = 1, S = 1)
6× Four-Lane (L = 4, M = 2, F = 1, S = 1)
8× Four-Lane (L = 4, M = 2, F = 1, S = 1)
12× Four-Lane (L = 4, M = 2, F = 1, S = 1)
16× Four-Lane (L = 4, M = 2, F = 1, S = 1)
24× Four-Lane (L = 4, M = 2, F = 1, S = 1)
8× Two-Lane (L = 2, M = 2, F = 2, S = 1)
12× Two-Lane (L = 2, M = 2, F = 2, S = 1)
16× Two-Lane (L = 2, M = 2, F = 2, S = 1)
24× Two-Lane (L = 2, M = 2, F = 2, S = 1)
16× One-Lane (L = 1, M = 2, F = 4, S = 1)
24× One-Lane (L = 1, M = 2, F = 4, S = 1)
1
Data Sheet
Required Samples from JESD204x Tx
Send two samples: M0S0, M1S0, repeat
Samples Assignment
SP0: M0S0, SP4: M0S0, SP8: M0S0, SP12: M0S0
SP1: M1S0, SP5: M1S0, SP9: M1S0, SP13: M1S0
SP2: M0S0, SP6: M0S0, SP10: M0S0, SP14: M0S0
SP3: M1S0, SP7: M1S0, SP11: M1S0, SP15: M1S0
Mx is the converter number and Sy is the sample number. For example, M0S0 means Converter 0, Sample 0. SPx is the sample pattern word number. For example, SP0
means Sample Pattern Word 0.
Repeated CGS and ILAS Test
As per Section 5.3.3.8.2 of the JESD204B specification, the
AD9164 can check that a constant stream of /K28.5/ characters
is being received, or that CGS followed by a constant stream of
ILAS is being received.
To run a repeated CGS test, send a constant stream of /K28.5/
characters to the AD9164 SERDES inputs. Next, set up the
device and enable the links. Ensure that the /K28.5/ characters are
being received by verifying that SYNCOUT± is deasserted and
that CGS has passed for all enabled link lanes by reading
Register 0x470.
To run the CGS followed by a repeated ILAS sequence test,
follow the procedure to set up the links, but before performing
the last write (enabling the links), enable the ILAS test mode by
writing a 1 to Register 0x477, Bit 7. Then, enable the links. When
the device recognizes four CGS characters on each lane, it
deasserts the SYNCOUT±. At this point, the transmitter starts
sending a repeated ILAS sequence.
Read Register 0x473 to verify that initial lane synchronization has
passed for all enabled link lanes.
values of the bad disparity error (BDE) count register is 1.
Reporting of disparity errors that occur at the same character
position of an NIT error is disabled. No such disabling is performed for the disparity errors in the characters after an NIT
error. Therefore, it is expected behavior that an NIT error may
result in a BDE error.
A resync is triggered when four NIT errors are injected with
Register 0x476, Bit 4 = 1. When this bit is set, the error counter
does not distinguish between a concurrent invalid symbol with
the wrong running disparity but is in the 8-bit/10-bit decoding
table, and an NIT error. Thus, a resync can be triggered when
four NIT errors are injected because they are not distinguished
from disparity errors.
Checking Error Counts
The error count can be checked for disparity errors, NIT errors,
and unexpected control character errors. The error counts are
on a per lane and per error type basis. Each error type and lane
has a register dedicated to it. To check the error count, the
following steps must be performed:
1.
JESD204B ERROR MONITORING
Disparity, Not in Table, and Unexpected Control (K)
Character Errors
As per Section 7.6 of the JESD204B specification, the AD9164
can detect disparity errors, not in table (NIT) errors, and
unexpected control character errors, and can optionally issue a
sync request and reinitialize the link when errors occur.
Note that the disparity error counter counts all characters with
invalid disparity, regardless of whether they are in the 8-bit/10-bit
decoding table. This is a minor deviation from the JESD204B
specification, which only counts disparity errors when they are
in the 8-bit/10-bit decoding table.
2.
3.
Several other interpretations of the JESD204B specification are
noted in this section. When three NIT errors are injected to one
lane and QUAL_RDERR (Register 0x476, Bit 4) = 1, the readback
Rev. A | Page 50 of 136
Choose and enable which errors to monitor by selecting
them in Register 0x480, Bits[5:3] to Register 0x487, Bits[5:3].
Unexpected K (UEK) character, BDE, and NIT error
monitoring can be selected for each lane by writing a 1 to
the appropriate bit, as described in the register map. These
bits are enabled by default.
The corresponding error counter reset bits are in
Register 0x480, Bits[2:0] to Register 0x487, Bits[2:0].
Write a 0 to the corresponding bit to reset that error
counter.
Registers 0x488, Bits[2:0] to Register 0x48F, Bits[2:0] have
the terminal count hold indicator for each error counter. If
this flag is enabled, when the terminal error count of 0xFF
is reached, the counter ceases counting and holds that
value until reset. Otherwise, it wraps to 0x00 and continues
counting. Select the desired behavior and program the
corresponding register bits per lane.
Data Sheet
AD9164
Check for Error Count Over Threshold
Table 31. Setting SYNCOUT± Error Pulse Duration
To check for the error count over threshold, follow these steps:
1.
2.
3.
Define the error counter threshold. The error counter
threshold can be set to a user defined value in Register 0x47C,
or left to the default value of 0xFF. When the error threshold is
reached, an IRQ is generated or SYNCOUT± is asserted or
both, depending on the mask register settings. This one error
threshold is used for all three types of errors (UEK, NIT,
and BDE).
Set the SYNC_ASSERT_MASK bits. The SYNCOUT±
assertion behavior is set in Register 0x47D, Bits[2:0]. By
default, when any error counter of any lane is equal to the
threshold, it asserts SYNCOUT± (Register 0x47D, Bits[2:0] =
0b111).
Read the error count reached indicator. Each error counter
has a terminal count reached indicator, per lane. This indicator is set to 1 when the terminal count of an error counter
for a particular lane has been reached. These status bits are
located in Register 0x490, Bits[2:0] to Register 0x497, Bits[2:0].
These registers also indicate whether a particular lane is
active by setting Bit 3 = 0b1.
Error Counter and IRQ Control
For error counter and IRQ control, follow these steps:
1.
2.
3.
Enable the interrupts. Enable the JESD204B interrupts. The
interrupts for the UEK, NIT, and BDE error counters are in
Register 0x4B8, Bits[7:5]. There are other interrupts to
monitor when bringing up the link, such as lane deskewing,
initial lane sync, good check sum, frame sync, code group sync
(Register 0x4B8, Bits[4:0], and configuration mismatch
(Register 0x4B9, Bit 0). These bits are off by default but can
be enabled by writing 0b1 to the corresponding bit.
Read the JESD204B interrupt status. The interrupt status
bits are in Register 0x4BA, Bits[7:0] and Register 0x4BB,
Bit 0, with the status bit position corresponding to the
enable bit position.
It is recommended to enable all interrupts that are planned
to be used prior to bringing up the JESD204B link. When
the link is up, the interrupts can be reset and then used to
monitor the link status.
F
1
2
4
1
These register settings assert the SYNCOUT± signal for two frame clock cycle
pulse widths.
Unexpected Control Character, NIT, Disparity IRQs
For UEK character, NIT, and disparity errors, error count over the
threshold events are available as IRQ events. Enable these events by
writing to Register 0x4B8, Bits[7:5]. The IRQ event status can be
read at Register 0x4BA, Bits[7:5] after the IRQs are enabled.
See the Error Counter and IRQ Control section for information on
resetting the IRQ. See the Interrupt Request Operation section for
more information on IRQs.
Errors Requiring Reinitializing
A link reinitialization automatically occurs when four invalid
disparity characters are received as per Section 7.1 of the JESD204B
specification. When a link reinitialization occurs, the resync
request is five frames and nine octets long.
The user can optionally reinitialize the link when the error
count for disparity errors, NIT errors, or UEK character errors
reaches a programmable error threshold. The process to enable
the reinitialization feature for certain error types is as follows:
1.
2.
3.
4.
Monitoring Errors via SYNCOUT±
When one or more disparity, NIT, or unexpected control
character errors occur, the error is reported on the SYNCOUT±
pin as per Section 7.6 of the JESD204B specification. The
JESD204B specification states that the SYNCOUT± signal is
asserted for exactly two frame periods when an error occurs. For
the AD9164, the width of theSYNCOUT± pulse can be
programmed to ½, 1, or 2 PCLK cycles. The settings to achieve a
SYNCOUT± pulse of two frame clock cycles are given in Table 31.
SYNC_ERR_DUR (Register 0x312,
Bits[7:4]) Setting1
0 (default)
1
2
PCLK Factor
(Frames/PCLK)
4
2
1
Choose and enable which errors to monitor by selecting
them in Register 0x480, Bits[5:3] to Register 0x487,
Bits[5:3]. UEK, BDE, and NIT error monitoring can be
selected for each lane by writing a 1 to the appropriate bit,
as described in Table 46. These are enabled by default.
Enable the sync assertion mask for each type of error by
writing to SYNC_ASSERT_MASK (Register 0x47D,
Bits[2:0]) according to Table 32.
Program the desired error counter threshold into
ERRORTHRES (Register 0x47C).
For each error type enabled in the SYNC_ASSERT_MASK
register, if the error counter on any lane reaches the
programmed threshold, SYNCOUT± falls, issuing a sync
request. Note that all error counts are reset when a link
reinitialization occurs. The IRQ does not reset and must be
reset manually.
Table 32. Sync Assertion Mask (SYNC_ASSERT_MASK)
Addr.
0x47D
Rev. A | Page 51 of 136
Bit No.
2
Bit Name
BDE
1
NIT
0
UEK
Description
Set to 1 to assert SYNCOUT± if
the disparity error count
reaches the threshold
Set to 1 to assert SYNCOUT± if
the NIT error count reaches
the threshold
Set to 1 to assert SYNCOUT± if
the UEK character error
count reaches the threshold
AD9164
Data Sheet
CGS, Frame Sync, Checksum, and ILAS Monitoring
Register 0x470 to Register 0x473 can be monitored to verify
that each stage of the JESD204B link establishment has
occurred.
Bit x of CODE_GRP_SYNC (Register 0x470) is high if Link
Lane x received at least four K28.5 characters and passed code
group synchronization.
Bit x of FRAME_SYNC (Register 0x471) is high if Link Lane x
completed initial frame synchronization.
Bit x of GOOD_CHECKSUM (Register 0x472) is high if the
checksum sent over the lane matches the sum of the JESD204B
parameters sent over the lane during ILAS for Link Lane x. The
parameters can be added either by summing the individual fields
in registers or summing the packed register. If Register 0x300,
Bit 6 = 0 (default), the calculated checksums are the lower eight
bits of the sum of the following fields: DID, BID, LID, SCR, L − 1,
F − 1, K − 1, M − 1, N − 1, SUBCLASSV, NP − 1, JESDV, S − 1,
and HD. If Register 0x300, Bit 6 = 1, the calculated checksums
are the lower eight bits of the sum of Register 0x400 to
Register 0x40C and LID.
Bits[3:0]. The IRQ event status can be read at Register 0x4BA,
Bits[3:0] after the IRQs are enabled. Write a 1 to Register 0x4BA,
Bit 0 to reset the CGS IRQ. Write a 1 to Register 0x4BA, Bit 1 to
reset the frame sync IRQ. Write a 1 to Register 0x4BA, Bit 2 to
reset the checksum IRQ. Write a 1 to Register 0x4BA, Bit 3 to
reset the ILAS IRQ.
See the Interrupt Request Operation section for more information.
Configuration Mismatch IRQ
The AD9164 has a configuration mismatch flag that is available
as an IRQ event. Use Register 0x4B9, Bit 0 to enable the mismatch
flag (it is enabled by default), and then use Register 0x4BB, Bit 0
to read back its status and reset the IRQ signal. See the Interrupt
Request Operation section for more information.
The configuration mismatch event flag is high when the link
configuration settings (in Register 0x450 to Register 0x45D) do
not match the JESD204B transmitted settings (Register 0x400 to
Register 0x40D).
Bit x of INIT_LANE_SYNC (Register 0x473) is high if Link
Lane x passed the initial lane alignment sequence.
This function is different from the good checksum flags in
Register 0x472. The good checksum flags ensure that the transmitted checksum matches a calculated checksum based on the
transmitted settings. The configuration mismatch event ensures
that the transmitted settings match the configured settings.
CGS, Frame Sync, Checksum, and ILAS IRQs
HARDWARE CONSIDERATIONS
Fail signals for CGS, frame sync, checksum, and ILAS are available
as IRQ events. Enable them by writing to Register 0x4B8,
See the Applications Information section for information on
hardware considerations.
Rev. A | Page 52 of 136
Data Sheet
AD9164
MAIN DIGITAL DATAPATH
HB
2×
HB
2×
NCO
HB
2×,
4×,
8×
HB
3×
INV
SINC
14414-104
JESD
Figure 109. Block Diagram of the Main Digital Datapath
The block diagram in Figure 109 shows the functionality of the
main digital datapath. The digital processing includes an input
interpolation block with choice of bypass 1×, 2×, or 3×
interpolation, three additional 2× half-band interpolation
filters, a final 2× NRZ mode interpolator filter, FIR85, that can
be bypassed, and a quadrature modulator that consists of a
48-bit NCO and an inverse sinc block.
All of the interpolation filters accept in-phase (I) and quadrature
(Q) data streams as a complex data stream. Similarly, the
quadrature modulator and inverse sinc function also accept
input data as a complex data stream. Thus, any use of the digital
datapath functions requires the input data to be a complex data
stream.
In bypass mode (1× interpolation), the input data stream is
expected to be real data.
Table 33. Pipeline Delay (Latency) for Various DAC Blocks
Mode
NCO only
1× (Bypass)
1× (Bypass)
2×
2×
2×
2×
2×
2×
3×
3×
4×
6×
8×
12×
16×
24×
FIR85
On
No
No
No
No
No
Yes
No
Yes
Yes
No
No
No
No
No
No
No
No
Filter
Bandwidth
N/A2
N/A2
N/A2
80%
90%
80%
80%
80%
80%
80%
90%
80%
80%
80%
80%
80%
80%
Inverse
Sinc
No
No
Yes
No
No
No
Yes
Yes
Yes
No
No
No
No
No
No
No
No
NCO
Yes
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
Pipeline Delay1
(fDAC Clocks)
48
113
137
155
176
202
185
239
279
168
202
308
332
602
674
1188
1272
The pipeline delay given is a representative number, and may vary by a cycle
or two based on the internal handoff timing conditions at startup.
2
N/A means not applicable.
1
The pipeline delay changes based on the digital datapath
functions that are selected. See Table 33 for examples of the
pipeline delay per block. These delays are in addition to the
JESD204B latency.
DATA FORMAT
The input data format for all modes on the AD9164 is 16-bit,
twos complement. The digital datapath and the DAC decoder
operate in twos complement format. The DAC is a current
steering DAC and cannot represent 0—it must either source or
sink current. As a result, when the 0 of twos complement is
represented in the DAC, it is a +1, and all the positive values
thereafter are shifted by +1. This mapping error introduces a ½ LSB
shift in the DAC output. The leakage can become apparent when
using the NCO to shift a signal that is above or below 0 Hz
when synthesized. The NCO frequency is seen as a small spur at
the NCO FTW.
To avoid the NCO frequency leakage, operate the DAC with a
slight digital backoff of one or several codes, and then add 1 to
all values in the data stream. These actions remove the NCO
frequency leakage but cause a half LSB dc offset. This small dc
offset is benign to the DAC and does not affect most applications
because the DAC output is ac-coupled through dc blocking
capacitors.
INTERPOLATION FILTERS
The main digital path contains five half-band interpolation
filters, plus a final half-band interpolation filter that is used in
2× NRZ mode. The filters are cascaded as shown in Figure 109.
The first pair of filters is a 2× (HB2) or 3× (HB3) filter. Each of
these filters has two options for bandwidth, 80% or 90%. The
80% filters are lower power than the 90%. The filters default to
the lower power 80% bandwidth. To select the filter bandwidth
as 90%, program the FILT_BW bit in the DATAPATH_CFG
register to 1 (Register 0x111, Bit 4 = 0b1).
Following the first pair of filters is a series of 2× half-band
filters, each of which halves the usable bandwidth of the
previous one. HB4 has 45%, HB5 has 22.5%, and HB6 has
11.25% of the fDATA bandwidth.
The final half-band filter, FIR85, is used in the 2× NRZ mode. It
is clocked at the 2 × fDAC rate and has a usable bandwidth of 45%
of the fDAC rate. The FIR85 filter is a complex filter, and therefore
the bandwidth is centered at 0 Hz. The FIR85 filter is used in
conjunction with the complex interpolation modes to push the
DAC update rate higher and move images further from the
desired signal.
Rev. A | Page 53 of 136
AD9164
Data Sheet
The interpolation filters interpolate between existing data in
such a way that they minimize changes in the incoming data
while suppressing the creation of interpolation images. This
datapath is shown for each filter in Figure 110.
The usable bandwidth (as shown in Table 34) is defined as the
frequency band over which the filters have a pass-band ripple of
less than ±0.001 dB and an image rejection of greater than 85 dB.
A conceptual drawing that shows the relative bandwidth of each
of the filters is shown in Figure 110. The maximum pass band
amplitude of all filters is the same; they are different in the
illustration to improve understanding.
8×
12×
16×
24×
FIR85
0
80
–0.1
70
–0.2
60
–0.3
50
–0.4
40
–0.5
30
IMAGE REJECTION
PASS-BAND RIPPLE
20
40
–0.6
41
42
43
44
45
BANDWIDTH (% fDATA )
Figure 111. Interpolation Filter Performance Beyond Specified Bandwidth for
the 80% Filters
FILTER RESPONSE
1×
2×
3×
4×
6×
90
MAXIMUM PASS-BAND RIPPLE (dB)
Filter Performance
Some of the interpolation filters are specified to 0.4 × fDATA (with
a pass band). The filters can be used slightly beyond this ratio at
the expense of increased pass-band ripple and decreased
interpolation image rejection.
14414-106
BWSIGNAL = BWFILT × (fDAC/InterpolationFactor)
Filter Performance Beyond Specified Bandwidth
MINIMUM INTERPOLATION IMAGE REJECTION (dB)
Table 34 shows how to select each available interpolation mode,
their usable bandwidths, and their maximum data rates. Calculate
the available signal bandwidth as the interpolator filter bandwidth,
BW, multiplied by fDAC/InterpolationFactor, as follows:
Figure 111 shows the performance of the interpolation filters
beyond 0.4 × fDATA. The ripple increases much slower than the
image rejection decreases. This means that if the application can
tolerate degraded image rejection from the interpolation filters,
more bandwidth can be used.
–1500
–500
500
1500
2500
FREQUENCY (MHz)
14414-105
Most of the filters are specified to 0.45 × fDATA (with pass band).
Figure 112 to Figure 119 show the filter response for each of the
interpolator filters on the AD9164.
Figure 110. All Band Responses of Interpolation Filters
Table 34. Interpolation Modes and Usable Bandwidth
Interpolation Mode
1× (Bypass)
2×
3×
4×
6×
8×
12×
16×
24×
2× NRZ (Register 0x111, Bit 0 = 1)
INTERP_MODE, Register 0x110, Bits[3:0]
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
Any combination3
Available Signal Bandwidth
(BW)1
fDAC/2
BW × fDATA/2
BW × fDATA/2
BW × fDATA/2
BW × fDATA/2
BW × fDATA/2
BW × fDATA/2
BW × fDATA/2
BW × fDATA/2
0.45 × fDAC4
Maximum fDATA (MHz)
fDAC2
fDAC/22
fDAC/3
fDAC/4
fDAC/6
fDAC/8
fDAC/12
fDAC/16
fDAC/24
fDAC (real) or fDAC/2 (complex)2
The data rate (fDATA) for all interpolator modes is a complex data rate, meaning each of I data and Q data run at that rate. Available signal bandwidth is the data rate
multiplied by the bandwidth of the initial 2× or 3× interpolator filters, which can be set to BW = 80% or BW = 90%. This bandwidth is centered at 0 Hz.
2
The maximum speed for 1× and 2× interpolation is limited by the JESD204B interface, and is 5000 MHz (real) in 1× or 2500 MHz (complex) in 2× interpolation mode.
3
The 2× NRZ filter, FIR85, can be used with any of the interpolator combinations.
4
The bandwidth of the FIR85 filter is centered at 0 Hz.
1
Rev. A | Page 54 of 136
Data Sheet
AD9164
20
20
0
0
–20
–40
–60
–80
–40
–60
–80
–100
–100
–120
–120
–140
–160
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
NORMALIZED FREQUENCY (Rad/Sample)
14414-158
–140
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
NORMALIZED FREQUENCY (Rad/Sample)
14414-161
MAGNITUDE (dB)
MAGNITUDE (dB)
–20
Figure 115. 3× Third-Band 90% Filter Response
Figure 112. First 2× Half-Band 80% Filter Response
20
20
0
0
–20
MAGNITUDE (dB)
–40
–60
–80
–40
–60
–80
–100
–120
–120
–140
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
NORMALIZED FREQUENCY (Rad/Sample)
–160
14414-159
–140
0
0
0
–20
–20
–40
–40
MAGNITUDE (dB)
MAGNITUDE (dB)
20
–60
–80
–120
–120
–140
–140
0.5
0.6
0.7
0.8
0.9
NORMALIZED FREQUENCY (Rad/Sample)
1.0
14414-160
–160
–160
0.4
0.5
0.6
0.7
0.8
0.9
1.0
–80
–100
0.3
0.4
–60
–100
0.2
0.3
Figure 116. Second 2× Half-Band 45% Filter Response
20
0.1
0.2
NORMALIZED FREQUENCY (Rad/Sample)
Figure 113. First 2× Half-Band 90% Filter Response
0
0.1
14414-162
–100
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
NORMALIZED FREQUENCY (Rad/Sample)
Figure 117. Third 2× Half-Band 22.5% Filter Response
Figure 114. 3× Third-Band 80% Filter Response
Rev. A | Page 55 of 136
1.0
14414-163
MAGNITUDE (dB)
–20
AD9164
Data Sheet
48-Bit Dual Modulus NCO
20
This modulation mode uses an NCO, a phase shifter, and a
complex modulator to modulate the signal by a programmable
carrier signal as shown in Figure 120. This configuration allows
output signals to be placed anywhere in the output spectrum
with very fine frequency resolution.
0
MAGNITUDE (dB)
–20
–40
–60
–80
–100
–140
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
NORMALIZED FREQUENCY (Rad/Sample)
14414-164
–120
Figure 118. Fourth 2× Half-Band 11.25% Filter Response
The NCO produces a quadrature carrier to translate the input
signal to a new center frequency. A quadrature carrier is a pair of
sinusoidal waveforms of the same frequency, offset 90° from
each other. The frequency of the quadrature carrier is set via a
FTW. The quadrature carrier is mixed with the I and Q data and
then summed into the I and Q datapaths, as shown in Figure 120.
Integer NCO Mode
The main 48-bit NCO can be used as an integer NCO by using
the following formula to create the frequency tuning word
(FTW):
20
0
−fDAC/2 ≤ fCARRIER < +fDAC/2
MAGNITUDE (dB)
–20
FTW = (fCARRIER/fDAC) × 248
–40
where FTW is a 48-bit, twos complement number.
–60
When in 2× NRZ mode (FIR85 enabled with Register 0x111,
Bit 0 = 1), the frequency tuning word is calculated as
–80
0 ≤ fCARRIER < fDAC
–120
FTW = (fCARRIER/fDAC) × 248
–140
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
NORMALIZED FREQUENCY (Rad/Sample)
1.0
14414-165
–100
Figure 119. FIR85 2× Half-Band 45% Filter Response
DIGITAL MODULATION
The AD9164 has digital modulation features to modulate the
baseband quadrature signal to the desired DAC output
frequency.
The AD9164 is equipped with several NCO modes. The default
NCO is a 48-bit, integer NCO. The A/B ratio of the dual
modulus NCO allows the output frequency to be synthesized
with very fine precision. NCO mode is selected as shown in
Table 35.
Table 35. Modulation Mode Selection
Modulation Mode
None
48-Bit Integer NCO
48-Bit Dual Modulus NCO
32-Bit FFH NCO
1
Modulation Type
Register 0x111, Register 0x111,
Bit 6
Bit 2
0b0
0b0
0b1
0b0
0b1
0b1
0b1
0b1
where FTW is a 48-bit binary number.
This method of calculation causes fCARRIER values in the second
Nyquist zone to appear to move to fDAC − fCARRIER when flipping
the FIR85 enable bit and not changing the FTW to account for
the change in number format.
The intended effect is that a sweep of the NCO from 0 Hz to
fDAC − fDAC/248 appears seamless when the FIR85 enable bit is set
to Register 0x111, Bit 0 = 0b1 prior to fCARRIER/fDAC = 0.5. As can
be seen from examination, the FTWs from 0 to less than fDAC/2
mean the same in either case, but they mean different fCARRIER
values from fDAC/2 to fDAC − fDAC/248. This effect must be considered
when constructing FTW values and using the 2× NRZ mode.
The frequency tuning word is set as shown in Table 36.
Table 36. NCO FTW Registers
Address
0x114
0x115
0x116
0x117
0x118
0x119
The FFH NCOs are enabled by writing a nonzero word to their FTW registers
when the main 48-bit NCO is enabled (see the Fast Frequency Hopping (FFH)
section). The modulus can be enabled or disabled. If the modulus is enabled,
the same modulus ratio applies to all the NCOs.
Rev. A | Page 56 of 136
Value
FTW[7:0]
FTW[15:8]
FTW[23:16]
FTW[31:24]
FTW[39:32]
FTW[47:40]
Description
8 LSBs of FTW
Next 8 bits of FTW
Next 8 bits of FTW
Next 8 bits of FTW
Next 8 bits of FTW
8 MSBs of FTW
Data Sheet
AD9164
Unlike other registers, the FTW registers are not updated immediately upon writing. Instead, the FTW registers update on the
rising edge of FTW_LOAD_REQ (Register 0x113, Bit 0). After
an update request, FTW_LOAD_ACK (Register 0x113, Bit 1) must
be high to acknowledge that the FTW has updated.
M/N = 250,000,000/2,500,000,000 = 1/10
The SEL_SIDEBAND bit (Register 0x111, Bit 1 = 0b1) is a convenience bit that can be set to use the lower sideband modulation
result, which is equivalent to flipping the sign of the FTW.
I DATA
Therefore, M = 1 and N = 10.
After calculation, X = 28147497671065, A = 3, and B = 5.
Programming these values into the registers for X, A, and B (X
is programmed in Register 0x114 to Register 0x119, B is
programmed in Register 0x124 to Register 0x129, and A is
programmed in Register 0x12A to Register 0x12F)) causes the
NCO to produce an output frequency of exactly 250 MHz given
a 2500 MHz sampling clock. For more details, refer to the AN-953
Application Note on the Analog Devices, Inc., website.
INTERPOLATION
COS(ωn + θ)
ω
π
NCO
θ
SIN(ωn + θ)
FTW[47:0]
NCO_PHASE_OFFSET
[15:0]
OUT_I
OUT_Q
–
+
NCO Reset
–1
Q DATA
0
1
14414-108
SEL_SIDEBAND
INTERPOLATION
Figure 120. NCO Modulator Block Diagram
Modulus NCO Mode (Direct Digital Synthesis (DDS))
The main 48-bit NCO can also be used in a dual modulus mode
to create fractional frequencies beyond the 48-bit accuracy. The
modulus mode is enabled by programming the MODULUS_EN bit
in the DATAPATH_CFG register to 1 (Register 0x111, Bit 2 = 0b1).
The frequency ratio for the programmable modulus direct digital
synthesis (DDS) is very similar to that of the typical accumulatorbased DDS. The only difference is that N is not required to be a
power of two for the programmable modulus, but can be an
arbitrary integer. In practice, hardware constraints place limits
on the range of values for N. As a result, the modulus extends the
use of the NCO to applications that require exact rational frequency
synthesis. The underlying function of the programmable
modulus technique is to alter the accumulator modulus.
Implementation of the programmable modulus function within
the AD9164 is such that the fraction, M/N, is expressible per
Equation 1. Note that the form of the equation implies a
compound frequency tuning word with X representing the
integer part and A/B representing the fractional part.
A
X+
f CARRIER
M
B
=
=
2 48
f DAC
N
frequency that is not a power of two submultiple of the sample
rate, namely fCARRIER = (1/10) fDAC, which is not possible with a
typical accumulator-based DDS. The frequency ratio, fCARRIER/fDAC,
leads directly to M and N, which are determined by reducing
the fraction (250,000,000/2,500,000,000) to its lowest terms, that is,
(1)
where:
X is programmed in Register 0x114 to Register 0x119.
A is programmed in Register 0x12A to Register 0x12F.
B is programmed in Register 0x124 to Register 0x129.
Programmable Modulus Example
Consider the case in which fDAC = 2500 MHz and the desired
value of fCARRIER is 250 MHz. This scenario synthesizes an output
Resetting the NCO can be useful when determining the start time
and phase of the NCO. The NCO can be reset by several different methods, including a SPI write, using the TX_ENABLE pin,
or by the SYSREF± signal. Due to internal timing variations
from device to device, these methods achieve an accuracy of
±6 DAC clock cycles.
Program Register 0x800, Bits[7:6] to 0b01 to set the NCO in phase
discontinuous switching mode via a write to the SPI port. Then,
any time the frequency tuning word is updated, the NCO phase
accumulator resets and the NCO begins counting at the new FTW.
Fast Frequency Hopping (FFH)
To support FFH, the AD9164 has several features in the NCO
block. There are two implementations of the NCO function.
The main 48-bit NCO is a general-purpose NCO and supports
some of the FFH modes, whereas the FFH NCO is specifically
designed to support several different FFH modes.
Main NCO Frequency Hopping
In the main 48-bit NCO, the mode of updating the frequency
tuning word can be changed from requiring a write to the
FTW_LOAD_REQ bit (Register 0x113, Bit 0) to an automatic
update mode. In the automatic update mode, the FTW is
updated as soon as the chosen FTW word is written.
To set the automatic FTW update mode, write the appropriate
word to the FTW_REQ_MODE bits (Register 0x113, Bits[6:4]),
choosing the particular FTW word that causes the automatic
update. For example, if relatively coarse frequency steps are
needed, it may be sufficient to write a single word to the MSB
byte of the FTW, and therefore the FTW_REQ_MODE bits can
be programmed to 110 (Register 0x113, Bits[6:4] = 0b110).
Then, each time the most significant byte, FTW5, is written, the
NCO FTW is automatically updated.
The FTW_REQ_MODE bits can be configured to use any of the
FTW words as the automatic update trigger word. This configuration provides convenience when choosing the order in which to
program the FTW registers.
Rev. A | Page 57 of 136
AD9164
Data Sheet
The speed of the SPI port write function is guaranteed, and is a
minimum of 100 MHz (see Table 4). Thus, the NCO FTW can
be updated in as little as 240 ns with a one register write in
automatic update mode.
This ensures that the phase accumulator is flushed of residual
values prior to receiving the all zeros word, which powers down
the output but not the accumulator. The accumulator is
powered down with the NCO_EN bit in Register 0x111, Bit 6.
FFH NCO
NCO Only Mode
The FFH NCO is implemented as the main 48-bit NCO with an
additional 31, 32-bit NCOs, with an associated bank of 31 FTWs.
These FTWs can be preloaded into the hopping frequency
register bank. Any of the 32 FTWs can be selected by a one
register write to the HOPF_SEL bits in the HOPF_CTRL register
(Register 0x800, Bits[4:0]). The manner in which the NCO
transitions to the new frequency is determined by the hopping
frequency change mode selection.
The AD9164 is capable of operating in a mode with only the NCO
enabled. In this mode, a single tone sine wave is generated by
the NCO engine and sent to the DAC output. All of the features
discussed in the Digital Modulation section are available in the
NCO only mode. It is not necessary to bring up the JESD204B
link in this mode. This mode is a useful option to bring up a
transmitter radio signal chain without needing a digital data
source, because the device generates the NCO data internally.
This mode can also be used in applications where a sine wave is
all that is needed, such as in a local oscillator application.
The FFH NCO supports several modes of fast frequency
hopping: phase continuous hopping, phase discontinuous
hopping, and phase coherent hopping. The hopping modes are
given in Table 37.
Table 37. NCO Frequency Change Mode
Register 0x800, Bits[7:6]
0b00
0b01
0b10
Description
Phase continuous switch
Phase discontinuous switch (reset
NCO accumulator)
Phase coherent switch
In phase continuous switching, the frequency tuning word of the
NCO is updated and the phase accumulator continues to accumulate to the new frequency. In phase discontinuous mode, the
FTW of the NCO is updated and the phase accumulator is reset,
making an instantaneous jump to the new frequency. In phase
coherent mode, the bank of additional 31 phase accumulators is
enabled, one each to shadow each FTW in the hopping
frequency register bank.
Upon enabling the phase coherent switching mode (Register 0x800,
Bits[7:6] = 0b10), all 32 NCO phase accumulators begin
counting simultaneously, and all continue counting regardless
of which individual NCO output is currently being used in the
digital datapath. In this way, the frequency of an individual
NCO can be chosen and is always phase coherent to Time 0.
Therefore, it is recommended to preload all FTWs, then select
the phase coherent switch mode to start them at the same time.
To conserve power, each of the 31 additional NCOs and phase
accumulators is enabled only when an FTW is programmed into its
register. To power down a particular NCO and phase accumulator,
program all zeros to the FTW register for a given NCO. All
NCO FTWs have a default value of 0x0. The main 48-bit NCO,
which is FTW0 in the FFH NCO, is enabled by the NCO_EN
bit in the DATAPATH_CFG register (Register 0x111, Bit 6 = 0b1).
To ensure that there is no residual power consumption or
possible residual spurious from one of the 32-bit NCOs after
powering it up and then powering it down, the suggested
method to power down the additional NCO is to first program
the FTW to 0x0001, and then program it to 0x0000.
To enable the NCO only mode, program the DC_TEST_EN bit
in Register 0x150, Bit 1 = 0b1. Then, program a dc value into
the twos complement dc test data word in Register 0x14E (MSB)
and Register 0x14F (LSB). The default value is 0x0000 (zero
amplitude), and a typical value to program is 0x7FFF for a fullscale tone. The final step is to program the interpolation value
to 1× bypass mode by selecting INTERP_MODE = 0b0000 in
Register 0x110, Bits[3:0]. This is necessary because the dc test
value is only available in the bypass path and is not accessible in
the complex datapath.
When DC_TEST_EN = 1, the data source of the digital datapath is
the dc test data word. This means that the JESD204B link can be
brought up and data can be successfully transferred to the device
over the link, but the data is not presented to the DAC when
DC_TEST_EN = 1. Connection to the SERDES data source is
only achieved when DC_TEST_EN = 0. The DC_TEST_EN bit
can be set on the fly, but because disabling the mode and
switching to the SERDES datapath normally requires the lanes
and/or interpolation mode to also be set, on the fly setting or
resetting of the DC_TEST_EN bit is normally not practical.
INVERSE SINC
The AD9164 provides a digital inverse sinc filter to compensate
the DAC roll-off over frequency. The filter is enabled by setting
the INVSINC_EN bit (Register 0x111, Bit 7) and is disabled by
default.
The inverse sinc (sinc−1) filter is a seven-tap FIR filter. Figure 121
shows the frequency response of sin(x)/x roll-off, the inverse
sinc filter, and the composite response. The composite response
has less than ±0.05 dB pass-band ripple up to a frequency of
0.4 × fDACCLK. When 2× NRZ mode is enabled, the inverse sinc
filter operates to 0.4 × f2×DACCLK. To provide the necessary
peaking at the upper end of the pass band, the inverse sinc filter
shown has an intrinsic insertion loss of about 3.8 dB.
Rev. A | Page 58 of 136
Data Sheet
AD9164
controlled function, namely to zero the input to the digital
datapath or to zero the output from the digital datapath. In
addition, the TX_ENABLE pin can also be configured to ramp
down (or up) the full-scale current of the DAC. The ramp down
reduces the output power of the DAC by about 20 dB from full
scale to the minimum output current.
1
SIN(x)/x ROLL-OFF
SINC–1 FILTER RESPONSE
COMPOSITE RESPONSE
–1
–2
The TX_ENABLE pin can also be programmed to reset the
NCO phase accumulator. See Table 38 for a description of the
settings available for the TX_ENABLE function.
–3
–4
Table 38. TX_ENABLE Settings
–5
Register
0x03F
Bit 7
0
0.05
0.10
0.15
0.20
0.25
0.30
0.35
FREQUENCY (× fDAC )
0.40
0.45
0.50
14414-109
MAGNITUDE (dB)
0
Figure 121. Responses of Sin(x)/x Roll-Off, the Sinc−1 Filter, and the
Composite of the Two
Bit 6
DOWNSTREAM PROTECTION
The AD9164 has several features designed to protect the power
amplifier (PA) of the system, as well as other downstream
blocks. They consist of a control signal from the LMFC sync
logic and a transmit enable function. The protection mechanism
in each case is the blanking of data that is passed to the DAC
decoder. The differences lie in the location in the datapath and
slight variations of functionality.
The JESD204B serial link has several flags and quality measures
to indicate the serial link is up and running error free. If any of
these measures flags an issue, a signal from the LMFC sync logic is
sent to a mux that stops data from flowing to the DAC decoder
and replaces it with 0s.
There are several transmit enable features, including a TX_
ENABLE register that can be used to squelch data at several
points in the datapath or configure the TX_ENABLE pin to do
likewise.
Transmit Enable
The transmit enable feature can be configured either as a SPI
controlled function or a pin controlled function. It can be used
for several different purposes. The SPI controlled function has
less accurate timing due to its reliance on a microcontroller to
program it; therefore, it is typically used as a preventative measure
at power-up or when configuring the device.
The SPI controlled TX_ENABLE function can be used to zero
the input to the digital datapath or to zero the output from the
digital datapath, as shown in Figure 122. If the input to the
digital datapath is zeroed, any filtering that is selected filters the
0 signal, causing a gradual ramp-down of energy in the digital
datapath. If the digital datapath is bypassed, as in 1÷ mode, the
data at the input to the DAC immediately drops to zero.
The TX_ENABLE pin can be used for more accurate timing
when enabling or disabling the DAC output. The effect of the
TX_ENABLE pin can be configured by the same TX_ENABLE
register (Register 0x03F) as is used for the SPI controlled functions, and it can be made to have the same effects as the SPI
Setting
0
1
0
1
Bits[5:4]
Bit 3
Bit 2
Bit 1
N/A1
0
1
0
1
0
1
Bit 0
0
1
1
2
Description
SPI control: zero data to the DAC
SPI control: allow data to pass to the
DAC
SPI control: zero data at input to the
datapath
SPI control: allow data to enter the
datapath
Reserved
Use SPI writes to reset the NCO2
Use TX_ENABLE to reset the NCO
Use SPI control to zero data to the DAC
Use TX_ENABLE pin to zero data to the
DAC
Use SPI control to zero data at the input
to the datapath
Use TX_ENABLE pin to zero data at
input to the datapath
Use SPI registers to control the full-scale
current
Use TX_ENABLE pin to control the fullscale current
N/A means not applicable.
Use SPI writes to reset the NCO if resetting the NCO is desired. Register 0x800,
Bits[7:6] determine whether the NCO is reset. See Table 37 for more details.
DATAPATH PRBS
The datapath PRBS can verify the AD9164 datapath receives
and correctly decodes data. The datapath PRBS verifies the
JESD204B parameters of the transmitter and receiver match, the
lanes of the receiver are mapped appropriately, the lanes are
appropriately inverted, and, if necessary, the start-up routine is
correctly implemented.
To run the datapath PRBS test, complete the following steps:
1.
2.
3.
4.
5.
6.
Rev. A | Page 59 of 136
Set up the device in the desired operating mode using the
start-up sequence.
Send PRBS7 or PRBS15 data.
Write Register 0x14B, Bit 2 = 0 for PRBS7 or 1 for PRBS15.
Write Register 0x14B, Bits[1:0] = 0b11 to enable and reset
the PRBS test.
Write Register 0x14B, Bits[1:0] = 0b01 to enable the PRBS
test and release reset.
Wait 500 ms.
AD9164
Data Sheet
7.
Check the status of the PRBS by checking the IRQ for the I
and Q path PRBS as described in the Datapath PRBS IRQ
section.
8. Read Register 0x14B, Bits[7:6]. Bit 6 is 0 if the I channel
has any errors. Bit 7 is 0 if the Q channel has any errors.
9. Read Register 0x14C to read the error count for the I channel.
10. Read Register 0x14D to read the error count for the Q
channel. The PRBS processes 32 bits at a time, and
compares the 32 new bits to the previous set of 32 bits. It
detects and reports only 1 error in every group of 32 bits;
therefore, the error count partly depends on when the
errors are seen.
For example, see the following sequence:
•
•
•
Bits: 32 good; 31 good, 1 bad; 32 good [2 errors]
Bits: 32 good; 22 good, 10 bad; 32 good [2 errors]
Bits: 32 good; 31 good, 1 bad; 31 good, 1 bad; 32 good
[3 errors]
DATAPATH PRBS IRQ
The PRBS fail signals for the I and Q path are available as IRQ
events. Use Register 0x020, Bits[1:0] to enable the fail signals,
and then use Register 0x024, Bits[1:0] to read back the status
and reset the IRQ signals. See the Interrupt Request Operation
section for more information.
DATA
TO DAC
0
0
MAIN
DIGITAL
PATH
0
FROM LMFC
SYNC LOGIC
FROM REG
0x03F[7]
FROM REG
0x03F[6]
FROM REG
0x03F[2]
FROM REG
0x03F[1]
Figure 122. Downstream Protection Block Diagram
Rev. A | Page 60 of 136
14414-110
TX_ENABLE
TX_ENABLE
Data Sheet
AD9164
INTERRUPT REQUEST OPERATION
The AD9164 provides an interrupt request output signal (IRQ)
on Ball G1 (8 mm × 8 mm CSP_BGA) or Ball G4 (11 mm ×
11 mm CSP_BGA) that can be used to notify an external host
processor of significant device events. On assertion of the
interrupt, query the device to determine the precise event that
occurred. The IRQ pin is an open-drain, active low output. Pull
the IRQ pin high, external to the device. This pin can be tied to
the interrupt pins of other devices with open-drain outputs to
wire-OR these pins together.
Figure 123 shows a simplified block diagram of how the IRQ
blocks work. If IRQ_EN is low, the INTERRUPT_SOURCE
signal is set to 0. If IRQ_EN is high, any rising edge of EVENT
causes the INTERRUPT_SOURCE signal to be set high. If any
INTERRUPT_SOURCE signal is high, the IRQ pin is pulled
low. INTERRUPT_SOURCE can be reset to 0 by either an
IRQ_RESET signal or a DEVICE_RESET signal.
Depending on the STATUS_MODE signal, the EVENT_STATUS
bit reads back an event signal or INTERRUPT_SOURCE signal.
The AD9164 has several interrupt register blocks (IRQ) that can
monitor up to 75 events (depending on device configuration).
Certain details vary by IRQ register block as described in Table 39.
Table 40 shows the source registers of the IRQ_EN, IRQ_RESET,
and STATUS_MODE signals in Figure 123, as well as the address
where EVENT_STATUS is read back.
Table 39. IRQ Register Block Details
Register Block
0x020, 0x024
Event Reported
Per chip
0x4B8 to 0x4BB;
0x470 to 0x473
Per link and lane
EVENT_STATUS
INTERRUPT_SOURCE if
IRQ is enabled; if not, it
is the event signal
INTERRUPT_SOURCE if
IRQ is enabled; if not, 0
INTERRUPT SERVICE ROUTINE
Interrupt request management starts by selecting the set of event
flags that require host intervention or monitoring. Enable the
events that require host action so that the host is notified when
they occur. For events requiring host intervention upon IRQ
activation, run the following routine to clear an interrupt request:
1.
2.
3.
4.
Read the status of the event flag bits that are being monitored.
Disable the interrupt by writing 0 to IRQ_EN.
Read the event source.
Perform any actions that may be required to clear the cause
of the event. In many cases, no specific actions may be
required.
Verify that the event source is functioning as expected.
Clear the interrupt by writing 1 to IRQ_RESET.
Enable the interrupt by writing 1 to IRQ_EN.
5.
6.
7.
0
1
EVENT_STATUS
STATUS_MODE
IRQ
IRQ_EN
EVENT
INTERRUPT_SOURCE
0
1
IRQ_EN
OTHER
INTERRUPT
SOURCES
IRQ_RESET
14414-111
DEVICE_RESET
Figure 123. Simplified Schematic of IRQ Circuitry
Table 40. IRQ Register Block Address of IRQ Signal Details
Register Block
0x020, 0x024
0x4B8 to 0x4BB
0x470 to 0x473
1
2
IRQ_EN
0x020; R/W per chip
0x4B8, 0x4B9; W per error type
0x470 to 0x473; W per error type
Address of IRQ Signals1
IRQ_RESET
STATUS_MODE2
0x024; W per chip
STATUS_MODE = IRQ_EN
0x4BA, 0x4BB; W per error type N/A, STATUS_MODE = 1
0x470 to 0x473; W per link
N/A, STATUS_MODE = 1
R is read; W is write; and R/W is read/write.
N/A means not applicable.
Rev. A | Page 61 of 136
EVENT_STATUS
0x024; R per chip
0x4BA, 0x4BB; R per chip
0x470 to 0x473; R per link
AD9164
Data Sheet
APPLICATIONS INFORMATION
HARDWARE CONSIDERATIONS
Power Sequencing
Power Supply Recommendations
The AD9164 requires power sequencing to avoid damage to the
DAC. A board design with the AD9164 must include a power
sequencer chip, such as the ADM1184, to ensure that the
domains power up in the correct order. The ADM1184 monitors
the level of power domains upon power-up. It sends an enable
signal to the next grouping of power domains. When all power
domains are powered up, a power-good signal is sent to the
system controller to indicate all power supplies are powered up.
All the AD9164 supply domains must remain as noise free as
possible for the best operation. Power supply noise has a frequency
component that affects performance, and is specified in volts rms
terms.
An LC filter on the output of the power supply is recommended
to attenuate the noise, and must be placed as close to the AD9164
as possible. The VDD12_CLK supply is the most noise sensitive
supply on the device, followed by the VDD25_DAC and
VNEG_N1P2 supplies, which are the DAC output rails. It is
highly recommended that the VDD12_CLK be supplied by
itself with an ultralow noise regulator such as the ADM7154 or
ADP1761 to achieve the best phase noise performance possible.
Noisier regulators impose phase noise onto the DAC output.
The VDD12A supply can be connected to the digital DVDD
supply with a separate filter network. All of the SERDES 1.2 V
supplies can be connected to one regulator with separate filter
networks. The IOVDD supply can be connected to the VDD25_
DAC supply with a separate filter network, or can be powered
from a system controller (for example, a microcontroller), 1.8 V
to 3.3 V supply. The power supply sequencing requirement
must be met; therefore, a switch or other solution must be used
when connected to the IOVDD supply with VDD25_DAC.
Take note of the maximum power consumption numbers given
in Table 3 to ensure the power supply design can tolerate temperature and IC process variation extremes. The amount of current
drawn is dependent on the chosen use cases, and specifications
are provided for several use cases to illustrate examples and
contributions from individual blocks, and to assist in calculating
the maximum required current per supply.
Another consideration for the power supply design is peak
current handling capability. The AD9164 draws more current in
the main digital supply when synthesizing a signal with
significant amplitude variations, such as a modulated signal, as
compared to when in idle mode or synthesizing a dc signal.
Therefore, the power supply must be able to supply current
quickly to accommodate burst signals such as GSM, TDMA, or
other signals that have an on/off time domain response. Because
the amount of current variation depends on the signals used, it
is best to perform lab testing first to establish ranges. A typical
difference can be several hundred milliamperes.
The IOVDD, VDD12A, VDD12_CLK, and DVDD domains
must be powered up first. Then, the VNEG_N1P2, VDD_1P2,
PLL_CLK_VDD12, DVDD_1P2, and SYNC_VDD_3P3 can be
powered up. The VDD25_DAC domain must be powered up
last. There is no requirement for a power-down sequence.
Power and Ground Planes
Solid ground planes are recommended to avoid ground loops
and to provide a solid, uninterrupted ground reference for the
high speed transmission lines that require controlled impedances.
It is recommended that power planes be stacked between
ground layers for high frequency filtering. Doing so adds extra
filtering and isolation between power supply domains in
addition to the decoupling capacitors.
Do not use segmented power planes as a reference for controlled
impedances unless the entire length of the controlled impedance
trace traverses across only a single segmented plane. These and
additional guidelines for the topology of high speed transmission
lines are described in the JESD204B Serial Interface Inputs
(SERDIN0± to SERDIN7±) section.
For some applications, where highest performance and higher
output frequencies are required, the choice of PCB materials
significantly impacts results. For example, materials such as
polyimide or materials from the Rogers Corporation can be
used, for example, to improve tolerance to high temperatures
and improve performance. Rogers 4350 material is used for the
top three layers in some of the evaluation board designs:
between the top signal layer and the ground layer below it,
between the ground layer and an internal signal layer, and
between that signal layer and another ground layer.
JESD204B Serial Interface Inputs (SERDIN0± to
SERDIN7±)
When considering the layout of the JESD204B serial interface
transmission lines, there are many factors to consider to
maintain optimal link performance. Among these factors are
insertion loss, return loss, signal skew, and the topology of the
differential traces.
Rev. A | Page 62 of 136
Data Sheet
AD9164
The JESD204B specification limits the amount of insertion loss
allowed in the transmission channel (see Figure 95). The AD9164
equalization circuitry allows significantly more loss in the channel
than is required by the JESD204B specification. It is still important
that the designer of the PCB minimize the amount of insertion
loss by adhering to the following guidelines:
•
•
•
Keep the differential traces short by placing the AD9164 as
near the transmitting logic device as possible and routing
the trace as directly as possible between the devices.
Route the differential pairs on a single plane using a solid
ground plane as a reference. It is recommended to route the
SERDES lanes on the same layer as the AD9164 to avoid vias
being used in the SERDES lanes.
Use a PCB material with a low dielectric constant (<4) to
minimize loss, if possible.
When choosing between the stripline and microstrip techniques,
keep in mind the following considerations: stripline has less loss
(see Figure 96 and Figure 97) and emits less EMI, but requires
the use of vias that can add complexity to the task of controlling
the impedance; whereas microstrip is easier to implement (if
the component placement and density allow routing on the top
layer) and eases the task of controlling the impedance.
If using the top layer of the PCB is problematic or the advantages
of stripline are desirable, follow these recommendations:
•
•
•
•
Minimize the number of vias.
If possible, use blind vias to eliminate via stub effects and
use microvias to minimize via inductance.
If using standard vias, use the maximum via length to
minimize the stub size. For example, on an 8-layer board,
use Layer 7 for the stripline pair (see Figure 124).
For each via pair, place a pair of ground vias adjacent to them
to minimize the impedance discontinuity (see Figure 124).
LAYER 1
ADD GROUND VIAS
y
STANDARD VIA
LAYER 5
y
DIFF+
LAYER 6
GND
LAYER 7
LAYER 8
y
DIFF–
LAYER 3
LAYER 4
GND
MINIMIZE STUB EFFECT
14414-100
LAYER 2
Figure 124. Minimizing Stub Effect and Adding Ground Vias for Differential
Stripline Traces
on a transmission line (see the Insertion Loss section). Maintain a
solid reference beneath (for microstrip) or above and below (for
stripline) the differential traces to ensure continuity in the
impedance of the transmission line. If the stripline technique is
used, follow the guidelines listed in the Insertion Loss section to
minimize impedance mismatches and stub effects.
Another primary source for impedance mismatch is at either
end of the transmission line, where care must be taken to match
the impedance of the termination to that of the transmission
line. The AD9164 handles this internally with a calibrated
termination scheme for the receiving end of the line. See the
Interface Power-Up and Input Termination section for details on
this circuit and the calibration routine.
Signal Skew
There are many sources for signal skew, but the two sources to
consider when laying out a PCB are interconnect skew within a
single JESD204B link and skew between multiple JESD204B
links. In each case, keeping the channel lengths matched to
within 12.5 mm is adequate for operating the JESD204B link at
speeds of up to 12.5 Gbps. This amount of channel length
match is equivalent to about 85% UI on the AD9164 evaluation
board. Managing the interconnect skew within a single link is
fairly straightforward. Managing multiple links across multiple
devices is more complex. However, follow the 12.5 mm
guideline for length matching. The AD9164 can handle more
skew than the 85% UI due to the six PCLK cycle buffer in the
JESD204B receiver, but matching the channel lengths as close as
possible is still recommended.
Topology
Structure the differential SERDINx± pairs to achieve 50 Ω to
ground for each half of the pair. Stripline vs. microstrip tradeoffs are described in the Insertion Loss section. In either case, it
is important to keep these transmission lines separated from
potential noise sources such as high speed digital signals and
noisy supplies. If using stripline differential traces, route them
using a coplanar method, with both traces on the same layer.
Although this method does not offer more noise immunity than
the broadside routing method (traces routed on adjacent
layers), it is easier to route and manufacture so that the
impedance continuity is maintained. An illustration of
broadside vs. coplanar is shown in Figure 125.
Tx DIFF A
Tx
DIFF A
Tx DIFF B
Return Loss
The JESD204B specification limits the amount of return loss
allowed in a converter device and a logic device, but does not
specify return loss for the channel. However, every effort must
be made to maintain a continuous impedance on the transmission line between the transmitting logic device and the AD9164.
Minimizing the use of vias, or eliminating them all together,
reduces one of the primary sources for impedance mismatches
Tx
DIFF B
Tx
ACTIVE
Tx ACTIVE
BROADSIDE DIFFERENTIAL Tx LINES
COPLANAR DIFFERENTIAL Tx LINES
Figure 125. Broadside vs. Coplanar Differential Stripline Routing Techniques
When considering the trace width vs. copper weight and
thickness, the speed of the interface must be considered. At
multigigabit speeds, the skin effect of the conducting material
confines the current flow to the surface. Maximize the surface
area of the conductor by making the trace width made wider to
Rev. A | Page 63 of 136
14414-101
Insertion Loss
AD9164
Data Sheet
reduce the losses. Additionally, loosely couple differential traces
to accommodate the wider trace widths. This coupling helps
reduce the crosstalk and minimize the impedance mismatch
when the traces must separate to accommodate components,
vias, connectors, or other routing obstacles. Tightly coupled vs.
loosely coupled differential traces are shown in Figure 126.
TIGHTLY COUPLED
DIFFERENTIAL Tx LINES
Tx
DIFF A
Tx
DIFF B
Separate the SYNCOUT± signal from other noisy signals,
because noise on the SYNCOUT± might be interpreted as a
request for /K/ characters.
LOOSELY COUPLED
DIFFERENTIAL Tx LINES
It is important to keep similar trace lengths for the CLK± and
SYSREF± signals from the clock source to each of the devices
on either end of the JESD204B links (see Figure 127). If using a
clock chip that can tightly control the phase of CLK± and
SYSREF±, the trace length matching requirements are greatly
reduced.
Figure 126. Tightly Coupled vs. Loosely Coupled Differential Traces
AC Coupling Capacitors
The AD9164 requires that the JESD204B input signals be accoupled to the source. These capacitors must be 100 nF and
placed as close as possible to the transmitting logic device. To
minimize the impedance mismatch at the pads, select the
package size of the capacitor so that the pad size on the PCB
matches the trace width as closely as possible.
LANE 0
LANE 1
Tx
DEVICE
Rx
DEVICE
LANE N – 1
LANE N
SYSREF±
DEVICE CLOCK
SYSREF±
CLOCK SOURCE
(AD9516-1, ADCLK925)
SYSREF± TRACE LENGTH
DEVICE CLOCK TRACE LENGTH
DEVICE CLOCK
SYSREF± TRACE LENGTH
DEVICE CLOCK TRACE LENGTH
Figure 127. SYSREF± Signal and Device Clock Trace Length
Rev. A | Page 64 of 136
14414-103
Tx
DIFF B
The SYNCOUT± and SYSREF± signals on the AD9164 are low
speed LVDS differential signals. Use controlled impedance traces
routed with 100 Ω differential impedance and 50 Ω to ground
when routing these signals. As with the SERDIN0± to
SERDIN7± data pairs, it is important to keep these signals separated from potential noise sources such as high speed digital
signals and noisy supplies.
14414-102
Tx
DIFF A
SYNCOUT±, SYSREF±, and CLK± Signals
Data Sheet
AD9164
ANALOG INTERFACE CONSIDERATIONS
The AD9164 uses the quad-switch architecture shown in Figure 128.
Only one pair of switches is enabled during a half-clock cycle, thus
requiring each pair to be clocked on alternative clock edges. A
key benefit of the quad-switch architecture is that it masks the code
dependent glitches that occur in the conventional two-switch
DAC architecture.
When Mix-Mode is used, the output is effectively chopped at
the DAC sample rate. This chopping has the effect of reducing
the power of the fundamental signal while increasing the power
of the images centered around the DAC sample rate, thus
improving the dynamic range of these images.
INPUT
DATA
D1
D2
D3
D4
D5
D6
D7
D8
D3
IOUTP
VG1
IOUTN
D4
–D7
D1
LATCHES V 3
G
DATA INPUT
–D8
D2
FOUR-SWITCH
DAC OUTPUT
(fS MIX-MODE)
VG2
VG1
VG2 VG3
VG4
D10
DACCLK_x
CLK±
CLK
D9
D5
–D9
–D6
–D10
t
–D5 D6
–D1
–D2
VG4
D10
–D4
D9
D7
–D3
14414-114
ANALOG MODES OF OPERATION
D8
14414-112
Figure 130. Mix-Mode Waveform
VSSA
Figure 128. Quad-Switch Architecture
In dual-switch architecture, when a switch transition occurs and
D1 and D2 are in different states, a glitch occurs. However, if D1
and D2 happen to be at the same state, the switch transitions and
no glitches occur. This code dependent glitching causes an
increased amount of distortion in the DAC. In quad-switch
architecture (no matter what the codes are), there are always
two switches that are transitioning at each half-clock cycle, thus
eliminating the code dependent glitches but, in the process,
creating a constant glitch at 2 × fDAC. For this reason, a significant
clock spur at 2 × fDAC is evident in the DAC output spectrum.
INPUT
DATA
D1
D2
D3
D4
D5
D6
D7
D8
D9
This ability to change modes provides the user the flexibility to
place a carrier anywhere in the first three Nyquist zones, depending
on the operating mode selected. Switching between baseband
and Mix-Mode reshapes the sinc roll-off inherent at the DAC
output. In baseband mode, the sinc null appears at fDACCLK because
the same sample latched on the rising clock edge is also latched
again on the falling clock edge, thus resulting in the same ubiquitous sinc response of a traditional DAC. In Mix-Mode, the
complement sample of the rising edge is latched on the falling
edge, therefore pushing the sinc null to 2 × fDACCLK. Figure 131
shows the ideal frequency response of the three modes with the
sinc roll-off included.
FIRST
NYQUIST ZONE
D10
SECOND
NYQUIST ZONE
0
DACCLK_x
THIRD
NYQUIST ZONE
MIX-MODE
–5
FOUR-SWITCH
DAC OUTPUT
(NORMAL MODE) D1
D2
D3
D4
D5
t
D6
D6
D2
D3
D4
D7
D7
D8
D8
D9
D9
D10
D10
D5
–15
NORMAL
MODE
–20
–25
t
–30
Figure 129. Two-Switch and Quad-Switch DAC Waveforms
–35
0FS
As a consequence of the quad-switch architecture enabling
updates on each half-clock cycle, it is possible to operate that
DAC core at 2× the DAC clock rate if new data samples are latched
into the DAC core on both the rising and falling edge of the
DAC clock. This notion serves as the basis when operating the
AD9164 in either Mix-Mode or return to zero (RZ) mode. In
each case, the DAC core is presented with new data samples on
each clock edge: in RZ mode, the rising edge clocks data and
the falling edge clocks zero, while in Mix-Mode; the falling edge
sample is simply the complement of the rising edge sample
value.
0.25FS
0.50FS
0.75FS
1.00FS
1.25FS
1.50FS
FREQUENCY (Hz)
14414-115
D1
14414-113
TWO-SWITCH
DAC OUTPUT
AMPLITUDE (dBFS)
RZ MODE
–10
Figure 131. Sinc Roll-Off for NRZ, RZ, and Mix-Mode Operation
The quad-switch can be configured via SPI (Register 0x152,
Bits[1:0]) to operate in either NRZ mode (0b00), RZ mode
(0b10), or Mix-Mode (0b01). The AD9164 has an additional
frequency response characteristic due to the FIR85 filter. This
filter samples data on both the rising and falling edges of the
DAC clock, in essence doubling the input clock frequency. As a
result, the NRZ (normal) mode roll-off in Figure 131 is extended to
2 × fDAC in Figure 131, and follows the Mix-Mode roll-off due to
the zero-order hold at 2 × DAC clock (see Figure 132).
Rev. A | Page 65 of 136
AD9164
Data Sheet
control (Bit 6), and set the duty cycle offset (Bits[4:0]). The duty
cycle offset word is a signed magnitude word, with Bit 4 being
the sign bit (1 is negative) and Bits[3:0] the magnitude. The duty
cycle adjusts across a range of approximately ±3%. Recommended
settings for this register are listed in the Start-Up Sequence section.
–6
–9
POWER (dBc)
–12
–15
–18
–21
–24
–27
–30
–36
0
1020 2040 3060 4080 5100 6120 7140 8160 9180 10200
FREQUENCY (MHz)
14414-193
–33
Figure 132. Sinc Roll-Off with 2× NRZ Mode Added, fDAC = 5.1 GSPS
CLOCK INPUT
The AD9164 contains a low jitter, differential clock receiver that
is capable of interfacing directly to a differential or single-ended
clock source. Because the input is self biased with a nominal
impedance of 90 Ω, it is recommended that the clock source be
ac-coupled to the CLK± input pins. The nominal differential
input is 1 V p-p, but the clock receiver can operate with a span
that ranges from 250 mV p-p to 2.0 V p-p. Better phase noise
performance is achieved with a higher clock input level.
DUTY CYCLE
RESTORER
TO DAC
AND DLL
CLK+
CROSS
CONTROL
CLK–
5kΩ
5kΩ
1.25V
14414-116
16µA
40kΩ
Figure 133. Clock Input
The quality of the clock source, as well as its interface to the
AD9164 clock input, directly impacts ac performance. Select the
phase noise and spur characteristics of the clock source to meet
the target application requirements. Phase noise and spurs at a
given frequency offset on the clock source are directly translated
to the output signal. It can be shown that the phase noise
characteristics of a reconstructed output sine wave are related to
the clock source by 20 × log10 (fOUT/fCLK) when the DAC clock
path contribution is negligible.
Figure 135 shows a clock source based on the ADF4355 low phase
noise/jitter PLL. The ADF4355 can provide output frequencies
from 54 MHz up to 6.8 GHz.
The clock control registers exist at Address 0x082 through
Address 0x084. CLK_DUTY (Register 0x082) can be used to
enable duty cycle correction (Bit 7), enable duty cycle offset
The clock input has a register that adjusts the phase of the CLK+
and CLK− inputs. This register is located at Address 0x07F. The
register has a signed magnitude (1 is negative) value that adds
capacitance at 20 fF per step to either the CLK+ or the CLK−
input, according to Table 41. The CLK_PHASE_TUNE register
can be used to adjust the clock input phase for better DAC
image rejection.
Table 41. CLK± Phase Adjust Values
Register 0x07F,
Bits[5:0]
000000
000001
000010
…
011111
100000
100001
100010
…
111111
Capacitance at
CLK+
0
1 × 20 fF
2 × 20 fF
…
31 × 20 fF
0
0
0
…
0
Capacitance at
CLK−
0
0
0
…
0
0
1 × 20 fF
2 × 20 fF
…
31 × 20 fF
The improvement in performance from making these
adjustments depends on the accuracy of the balance of the clock
input balun and varies from unit to unit. Thus, if a high level of
image rejection is required, it is likely that a per unit calibration
is necessary. Performing this calibration can yield significant
improvements, as much as 20 dB additional rejection of the
image due to imbalance. Figure 134 shows the results of tuning
clock phase, duty cycle (left at default in this case), and cross
control. The improvement to performance, particularly at
higher frequencies, can be as much as 20 dB.
–20
–30
–40
PHASE 0,
CROSS 6
–50
–60
–70
PHASE 28,
CROSS 10
–80
–90
0
1000
2000
3000
fOUT (MHz)
4000
5000
6000
14414-221
NRZ MODE
2× NRZ MODE
MIX-MODE
RZ MODE
DAC OUTPUT IMAGE POWER (fS – fOUT) (dBc)
0
–3
Figure 134. Performance Improvement from Tuning the Clock Input
Rev. A | Page 66 of 136
Data Sheet
AD9164
VOUT
AD9164
ADF4355
7.4nH
100pF
CLK+
PLL
OUTPUT
STAGE
VCO
100pF
CLK–
fREF
VOUT 2GHz TO 6GHz
0dBm
14414-174
7.4nH
Figure 135. Possible Signal Chain for CLK± Input
SHUFFLE MODE
The spurious performance of the AD9164 can be improved with
a feature called shuffle mode. Shuffle mode uses proprietary
technology to spread the energy of spurious signals across the
DAC output as random noise. Shuffle mode is enabled by
programming Register 0x151, Bit 2 = 0b1. Because shuffle is
implemented with the MSBs, it is more effective when the DAC
is operated with a small amount of digital backoff.
The amount of noise rise caused by shuffle mode is directly
related to the power in the affected spurious signals. Because
the AD9164 has good spurious performance without shuffle
active, the penalty of shuffle mode to the noise spectral density
is typically about 1 dB to 3 dB. Shuffle mode reduces spurious
performance related to clock and foldback spurs, but does not
affect real harmonics of the DAC output. Examples of the
effects of shuffle mode are given in the Typical Performance
Characteristics section (see Figure 48, Figure 49, Figure 63,
Figure 64, and Figure 65).
DLL
The CLK± input goes to a high frequency DLL to ensure robust
locking of the DAC sample clock to the input clock. The DLL is
configured and enabled as part of the recommended start-up
sequence. The DLL control registers are located at Register 0x090
through Register 0x09B. The DLL settings are determined during
product characterization and are given in the recommended
start-up sequence (see the Start-Up Sequence section). It is not
normally necessary to change these values, nor is the product
characterization data valid on any settings other than the recommended ones.
VOLTAGE REFERENCE
The AD9164 output current is set by a combination of digital
control bits and the ISET reference current, as shown in Figure 136.
VREF
ISET
1µF
VSS
Note the following constraints when configuring the voltage
reference circuit:
•
•
•
•
•
Both the 9.6 kΩ resistor and 1 µF bypass capacitor are
required for proper operation.
Adjusting the DAC output full-scale current, IOUTFS, from
its default setting of 40 mA must be performed digitally.
The AD9164 is not a multiplying DAC. Modulation of the
reference current, ISET, with an ac signal is not supported.
The band gap voltage appearing at the VREF pin must be
buffered for use with an external circuitry because it has a
high output impedance.
An external reference can be used to overdrive the internal
reference by connecting it to the VREF pin.
The IOUTFS value can be adjusted digitally over an 8 mA to
40 mA range by the ANA_FULL_SCALE_CURRENT[9:0] bits
(Register 0x042, Bits[7:0] and Register 0x041, Bits[1:0]). The
following equation relates IOUTFS to the ANA_FULL_SCALE_
CURRENT[9:0] bits, which can be set from 0 to 1023.
IOUTFS = 32 mA × (ANA_FULL_SCALE_CURRENT[9:0]/1023) +
8 mA
Note that the default value of 0x3FF generates 40 mA full scale,
and this value is used for most of the characterization presented
in this data sheet, unless noted otherwise.
The AD9164 has a band gap temperature sensor for monitoring
the temperature changes of the AD9164. The temperature must
be calibrated against a known temperature to remove the device
to device variation on the band gap circuit that senses the
temperature.
DAC
–
CURRENT
SCALING
IOUTFS
ISET
VNEG_N1P2
Figure 136. Voltage Reference Circuit
14414-119
9.6kΩ
ANA_FULL_SCALE_CURRENT [9:0]
+
IOUTFS = 1.2 V/RSET × 320 (mA)
TEMPERATURE SENSOR
AD9164
VBG
1.2V
The reference current is obtained by forcing the band gap
voltage across an external 9.6 kΩ resistor from ISET (Ball A15
on the 165-ball CSP_BGA and Ball A12 on the 169-ball
CSP_BGA) to VNEG_N1P2. The 1.2 V nominal band gap
voltage (VREF) generates a 125 µA reference current, ISET, in
the 9.6 kΩ resistor, RSET. The maximum full-scale current
setting is related to the external resistor by the following
equation:
To calibrate the temperature, the user must take a reading at a
known ambient temperature for a single point calibration of the
AD9164 device. The slope for the formula is then calculated as
Rev. A | Page 67 of 136
AD9164
Data Sheet
where:
TREF is the calibrated temperature at which the temperature sensor
is read.
CODE_REF is the readback code at the measured temperature,
TREF.
To monitor temperature change,
TX = TREF + M × (CODE_X − CODE_REF)/1000
where:
CODE_X is the readback code at the unknown temperature, TX.
CODE_REF is the readback code at the calibrated temperature,
TREF.
The current that is measured at the OUTPUT+ and OUTPUT−
outputs is as follows:
OUTPUT+ = (IFIXED (mA) + (F × IOUTFS)/FMAX(mA)) ×
(RINT/(RINT + RLOAD))
OUTPUT− = (IFIXED (mA) + ((FMAX − F) ×
IOUTFS)/FMAX(mA)) ×(RINT/(RINT + RLOAD))
The IFIXED value is about 3.8 mA. It is important to note that the
AD9164 output cannot support dc coupling to the external load,
and thus must be ac-coupled through appropriately sized capacitors
for the chosen operating frequencies. Figure 138 shows the
OUTPUT+ vs. DAC code transfer function when IOUTFS is set to
40 mA.
45
To use the temperature sensor, enable the sensor by setting Register
0x135 to Register 0xA1. The user must write a 1 to Register 0x134,
Bit 0 before reading back the die temperature from Register 0x132
(LSB) and Register 0x133 (MSB).
40
OUTPUT CURRENT (mA)
35
ANALOG OUTPUTS
Equivalent DAC Output and Transfer Function
The AD9164 provides complementary current outputs, OUTPUT+
and OUTPUT−, that sink current from an external load that is
referenced to the 2.5 V VDD25_DAC supply. Figure 137 shows
an equivalent output circuit for the DAC. Compared to most
current output DACs of this type, the outputs of the AD9164
consists of a constant current (IFIXED), and a peak differential ac
current, ICS (ICS = ICSP + ICSN). These two currents combine to
form the IINTx currents shown in Figure 137. The internal
currents, IINTP and IINTN, are sent to the output pin and to an
input termination resistance equivalent to 100 Ω pulled to the
VDD25_DAC supply (RINT). This termination serves to divide the
output current based on the external termination resistors that
are pulled to VDD25_DAC.
VDD25_DAC
IOUTFS = 8mA – 40mA
100Ω
ICSP
IINTP
IFIXED
IFIXED
IINTN
OUTPUT–
100Ω
VDD25_DAC
14414-120
ICSN
OUTPUT+
Figure 137. Equivalent DAC Output Circuit
The example shown in Figure 137 can be modeled as a pair of
dc current sources that source a current of IOUT to each output.
This differential ac current source is used to model the signal
(that is, a digital code) dependent nature of the DAC output.
The polarity and signal dependency of this ac current source are
related to the digital code (F) by the following equation:
F (code) = (DACCODE – 32,768)/32,768
where:
−1 ≤ F (code) < +1.
DACCODE = 0 to 65,535 (decimal).
(2)
(3)
30
25
20
15
10
5
0
0
16384
32768
DAC CODE
49152
65536
14414-121
M = (TREF + 190)/((CODE_REF)/1000)
Figure 138. Gain Curve for ANA_FULL_SCALE_CURRENT[9:0] = 1023, DAC
Offset = 3.8 mA
Peak DAC Output Power Capability
The maximum peak power capability of a differential current
output DAC is dependent on its peak differential ac current,
IPEAK, and the equivalent load resistance it sees. In the case of a
1:1 balun with 100 Ω differential source termination, the equivalent load that is seen by the DAC ac current source is 50 Ω. If
the AD9164 is programmed for an IOUTFS = 40 mA, its ideal peak ac
current is 20 mA and its maximum power, delivered to the
equivalent load, is 10 × (RINT/(RINT + RLOAD) = 8 mW (that is, P =
I2R). Because the source and load resistance seen by the 1:1 balun
are equal, this power is shared equally. Therefore, the output load
receives 4 mW, or 6 dBm maximum power.
To calculate the rms power delivered to the load, consider the
following:
•
•
•
•
Peak to rms of the digital waveform
Any digital backoff from digital full scale
DAC sinc response and nonideal losses in the external
network
DAC analog roll-off due to switch parasitic capacitance and
load impedance
For example, a sine wave with no digital backoff ideally measures
6 dBm. If a typical balun loss of 1.2 dB is included, expect to
measure 4.8 dBm of actual power in the region where the sinc
response of the DAC has negligible influence and analog roll-off
Rev. A | Page 68 of 136
Data Sheet
AD9164
has not begun. Increasing the output power is best accomplished
by increasing IOUTFS. An example of DAC output characteristics
for several balun and board types is shown in Figure 139.
Most applications that require balanced to unbalanced conversion
from 10 MHz to 3 GHz can take advantage of several available
transformers that offer impedance ratios of both 2:1 and 1:1.
Figure 140 shows the AD9164 interfacing to the Mini-Circuits
TCM1-63AX+ and the TC1-1-43X+ transformers.
5
MINI-CIRCUITS
TCM1-63AX+
TC1-1-43X+
OUTPUT+
–5
L
50Ω
C
L
50Ω
C
–10
OUTPUT–
Figure 140. Recommended Transformer for Wideband Applications with
Upper Bandwidths of up to 5 GHz
–15
0
1
2
3
4
5
fOUT (GHz)
6
14414-123
BAL-0006
TC1-1-43X+
TCM1-63AX+
–20
14414-122
VDD25_DAC
Figure 139. Measured DAC Output Response; fDAC = 6 GSPS
Output Stage Configuration
The AD9164 is intended to serve high dynamic range
applications that require wide signal reconstruction bandwidth
(such as a DOCSIS cable modem termination system (CMTS))
and/or high IF/RF signal generation. Optimum ac performance
can be realized only when the DAC output is configured for
differential (that is, balanced) operation with its output commonmode voltage biased to a stable, low noise 2.5 V nominal analog
supply (VDD25_DAC).
The output network used to interface to the DAC provides a near
0 Ω dc bias path to VDD25_DAC. Any imbalance in the output
impedance over frequency between the OUTPUT+ and OUTPUT−
pins degrades the distortion performance (mostly even order)
and noise performance. Component selection and layout are
critical in realizing the performance potential of the AD9164.
To assist in matching the AD9164 output, an equivalent model
of the output was developed, and is shown in Figure 141. This
equivalent model includes all effects from the ideal 40 mA current
source in the die to the ball of the CSP_ BGA package, including
parasitic capacitance, trace inductance and resistance, contact
resistance of solder bumps, via inductance, and other effects.
470pH
40mA
179Ω
3.59Ω
1.14pF
470pH
OUTPUT–
248fF
3.59Ω
OUTPUT+
14414-124
OUTPUT POWER (dBm)
0
Figure 141. Equivalent Circuit Model of the DAC Output
A Smith chart is provided in Figure 142 showing the simulated
S11 of the DAC output, using the model in Figure 141. The plot
was taken using the circuit in Figure 141, with a 100 Ω
differential load instead of the balun. For the measured response
of the DAC output, see Figure 139.
Rev. A | Page 69 of 136
AD9164
Data Sheet
1.0
2.0
0.5
m1
0.2
5.0
S (1, 1)
m6
m2
0
0
m5
m3
m4
–5.0
–0.2
–0.5
–2.0
m1
FREQUENCY = 10MHz
S (1, 1) = 0.770/149.556
IMPEDANCE = Z0 × (0.140 + j0.267)
m4
FREQUENCY = 2GHz
S (1, 1) = 0.583/–148.777
IMPEDANCE = Z0 × (0.282 – j0.259)
m2
FREQUENCY = 100MHz
S (1, 1) = 0.227/163.083
IMPEDANCE = Z0 × (0.638 + j0.089)
m5
FREQUENCY = 4GHz
S (1, 1) = 0.794/–170.517
IMPEDANCE = Z0 × (0.116 – j0.082)
m3
FREQUENCY = 1GHz
S (1, 1) = 0.367/–144.722
IMPEDANCE = Z0 × (0.499 – j0.245)
m6
FREQUENCY = 6GHz
S (1, 1) = 0.779/168.448
IMPEDANCE = Z0 × (0.125 + j0.100)
14414-125
–1.0
FREQUENCY (10MHz TO 6GHz)
Figure 142. Simulated Smith Chart Showing the DAC Output Impedance
ZO = 100 Ω
Rev. A | Page 70 of 136
Data Sheet
AD9164
START-UP SEQUENCE
Several steps are required to program the AD9164 to the proper
operating state after the device is powered up. This sequence is
divided into several steps, and is listed in Table 42, Table 43, and
Table 44, along with an explanation of the purpose of each step.
Private registers are reserved but must be written for proper
operation. Blank cells in Table 42 to Table 44 mean that the value
depends on the result as described in the description column.
The AD9164 is calibrated at the factory as part of the automatic
test program. The configure DAC start-up sequence loads the
factory calibration coefficients, as well as configures some
parameters that optimize the performance of the DAC and the
DAC clock DLL (see Table 42). Run this sequence whenever the
DAC is powered down or reset.
The configure JESD204B sequence configures the SERDES
block and then brings up the links (see Table 43). First, run the
configure DAC start-up sequence, then run the configure
JESD204B sequence.
Follow the configure NCO sequence if using the NCO (see
Table 44). Note that the NCO can be used in NCO only mode
or in conjunction with synthesized data from the SERDES data
interface. Only one mode can be used at a time and this mode is
selected in the second step in Table 44. The configure DAC
start-up sequence is run first, then the configure NCO sequence.
Table 42. Configure DAC Start-Up Sequence After Power-Up
R/W
W
W
W
W
W
W
R
Value
0x18
0x52
0xD2
0x02
0x00
0x01
N/A1
R
Register
0x000
0x0D2
0x0D2
0x606
0x607
0x604
0x003, 0x004, 0x005,
0x006
0x604, Bit 1
W
W
W
W
W
W
W
R
0x058
0x090
0x080
0x040
0x020
0x09E
0x091
0x092, Bit 0
0x03
0x1E
0x00
0x00
0x0F
0x85
0xE9
0b1
W
W
0x0E8
0x152, Bits[1:0]
0x20
1
0b1
Description
Configure the device for 4-wire serial port operation (optional: leave at the default of 3-wire SPI).
Reset internal calibration registers (private).
Clear the reset bit for the internal calibration registers (private).
Configure the nonvolatile random access memory (NVRAM) (private).
Configure the NVRAM (private).
Load the NVRAM. Loads factory calibration factors from the NVRAM (private).
(Optional) read CHIP_TYPE, PROD_ID[15:0], PROD_GRADE, and DEV_REVISION from Register 0x003,
Register 0x004, Register 0x005, and Register 0x006.
(Optional) read the boot loader pass bit in Register 0x604, Bit 1 = 0b1 to indicate a successful boot
load.
Enable the band gap reference (private).
Power up the DAC clock DLL.
Enable the clock receiver.
Enable the DAC bias circuits.
Optional. Enable the interrupts.
Configure DAC analog parameters (private).
Enable the DAC clock DLL.
Check DLL_STATUS; set Register 0x092, Bit 0 = 1 to indicate the DAC clock DLL is locked to the DAC
clock input.
Enable calibration factors (private).
Configure the DAC decode mode (0b00 = NRZ, 0b01 = Mix-Mode, or 0b10 = RZ).
N/A means not applicable.
Table 43. Configure JESD204B Start-Up Sequence
R/W
W
W
W
W
W
W
W
W
W
W
W
W
Register
0x300
0x4B8
0x4B9
0x480
0x481
0x482
0x483
0x484
0x485
0x486
0x487
0x110
Value
0x00
0xFF
0x01
0x38
0x38
0x38
0x38
0x38
0x38
0x38
0x38
Description
Ensure the SERDES links are disabled before configuring them.
Enable JESD204B interrupts.
Enable JESD204B interrupts.
Enable SERDES error counters.
Enable SERDES error counters.
Enable SERDES error counters.
Enable SERDES error counters.
Enable SERDES error counters.
Enable SERDES error counters.
Enable SERDES error counters.
Enable SERDES error counters.
Configure number of lanes (Bits[7:4]) and interpolation rate (Bits[3:0]).
Rev. A | Page 71 of 136
AD9164
Data Sheet
R/W
W
Register
0x111
W
W
W
W
W
W
W
W
R
0x230
0x289,
Bits[1:0]
0x084,
Bits[5:4]
0x200
0x475
0x453, Bit 7
0x458,
Bits[7:5]
0x459,
Bits[7:5]
0x45D
0x475
0x201,
Bits[7:0]
0x2A7
0x2AE
0x29E
0x206
0x206
0x280
0x281, Bit 0
0x01
0x01
0x1F
0x00
0x01
0x03
0b1
W
R
R
R
R
W
W
W
0x300
0x470
0x471
0x472
0x473
0x024
0x4BA
0x4BB
0x01
0xFF
0xFF
0xFF
0xFF
0x1F
0xFF
0x01
W
W
W
W
W
W
W
W
W
Value
Description
Configure the datapath options for Bit 7 (INVSINC_EN), Bit 6 (NCO_EN), Bit 4 (FILT_BW), Bit 2
(MODULUS_EN), Bit 1 (SEL_SIDEBAND), and Bit 0 (FIR85_FILT_EN). See the Register Summary section for
details on the options. Set the reserved bits (Bit 5 and Bit 3) to 0b0.
Configure the CDR block according to Table 19 for both half rate enable and the divider.
Set up the SERDES PLL divider based on the conditions shown in Table 18.
Set up the PLL reference clock rate based on the conditions shown in Table 18.
0x00
0x09
0b1
Enable JESD204B block (disable master SERDES power-down).
Soft reset the JESD204B quad-byte deframer.
(Optional) Enable scrambling on SERDES lanes.
Set the subclass type: 0b000 = Subclass 0, 0b001 = Subclass 1.
0b1
Set the JESD204x version to JESD204B.
0x01
Program the calculated checksum value for Lane 0 from values in Register 0x450 to Register 0x45C.
Bring the JESD204B quad-byte deframer out of reset.
Set any bits to 1 to power down the appropriate physical lane.
(Optional) Calibrate SERDES PHY Termination Block 1 (PHY 0, PHY 1, PHY 6, PHY 7).
(Optional) Calibrate SERDES PHY Termination Block 2 (PHY 2, PHY 3, PHY 4, PHY 5).
Override defaults in the SERDES PLL settings (private).
Reset the CDR.
Enable the CDR.
Enable the SERDES PLL.
Read back Register 0x281 until Bit 0 = 1 to indicate the SERDES PLL is locked. Prior to enabling the links, be
sure that the JESD204B transmitter is enabled and ready to begin bringing up the link.
Enable SERDES links (begin bringing up the link).
Read the CGS status for all lanes.
Read the frame sync status for all lanes.
Read the good checksum status for all lanes.
Read the initial lane sync status for all lanes.
Clear the interrupts.
Clear the SERDES interrupts.
Clear the SERDES interrupt.
Table 44. Configure NCO Sequence
R/W
W
W
Register
0x110
0x111, Bit 6
W
W
W
W
W
W
W
W
W
W
W
0x150, Bit 1
0x14E
0x14F
0x113
0x119
0x118
0x117
0x116
0x115
0x114
0x113
Value
0x80
0b1
0x00
0x01
Description
(Optional). Perform this write if NCO only mode is desired.
Configure NCO_EN (Bit 6) = 0b1. Configure other datapath options for Bit 7 (INVSINC_EN), Bit 4 (FILT_BW),
Bit 2 (MODULUS_EN), Bit 1 (SEL_SIDEBAND), and Bit 0 (FIR85_FILT_EN). See the Register Summary section
for details on the options. Set the reserved bits (Bit 5 and Bit 3) to 0b0.
Configure DC_TEST_EN bit: 0b0 = NCO operation with data interface; 0b1 = NCO only mode.
Write amplitude value for tone amplitude in NCO only mode (Bits [15:8]).
Write amplitude value for tone amplitude in NCO only mode (Bits [7:0]).
Ensure the frequency tuning word write request is low.
Write FTW, Bits[47:40].
Write FTW, Bits[39:32].
Write FTW, Bits[31:24].
Write FTW, Bits[23:16].
Write FTW, Bits[15:8].
Write FTW, Bits[7:0].
Load the FTW to the NCO.
Rev. A | Page 72 of 136
Data Sheet
AD9164
REGISTER SUMMARY
Table 45. Register Summary
Reg.
Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
0x000
SPI_INTFCONFA
[7:0]
SOFTRESET_
M
LSBFIRST_M
ADDRINC_M
SDOACTIVE_ SDOACTIVE
M
Bit 3
0x001
SPI_INTFCONFB
[7:0]
SINGLEINS
CSSTALL
0x002
SPI_DEVCONF
[7:0]
0x003
SPI_CHIPTYPE
[7:0]
0x004
SPI_PRODIDL
[7:0]
PROD_ID[7:0]
0x00 R
0x005
SPI_PRODIDH
[7:0]
PROD_ID[15:8]
0x00 R
0x006
SPI_CHIPGRADE
[7:0]
0x020
IRQ_ENABLE
[7:0]
RESERVED
EN_SYSREF_
JITTER
0x024
IRQ_STATUS
[7:0]
RESERVED
IRQ_SYSREF_ IRQ_DATA_
JITTER
READY
0x031
SYNC_LMFC_
DELAY_FRAME
[7:0]
RESERVED
0x032
SYNC_LMFC_
DELAY0
[7:0]
0x033
SYNC_LMFC_
DELAY1
[7:0]
0x034
SYNC_LMFC_
STAT0
[7:0]
0x035
SYNC_LMFC_
STAT1
[7:0]
0x036
SYSREF_COUNT
[7:0]
SYSREF_COUNT
0x00 R/W
0x037
SYSREF_PHASE0
[7:0]
SYSREF_PHASE[7:0]
0x00 R/W
0x038
SYSREF_PHASE1
[7:0]
0x039
SYSREF_JITTER_
WINDOW
[7:0]
0x03A
SYNC_CTRL
[7:0]
0x03F
TX_ENABLE
[7:0]
0x040
ANA_DAC_BIAS_
PD
[7:0]
RESERVED
0x041
ANA_FSC0
[7:0]
RESERVED
0x042
ANA_FSC1
[7:0]
0x07F
CLK_PHASE_TUNE [7:0]
0x080
CLK_PD
[7:0]
0x082
CLK_DUTY
[7:0]
CLK_DUTY_
EN
0x083
CLK_CRS_CTRL
[7:0]
CLK_CRS_EN
0x084
PLL_REF_CLK_PD [7:0]
0x088
SYSREF_CTRL0
[7:0]
0x089
SYSREF_CTRL1
[7:0]
0x090
DLL_PD
[7:0]
0x091
DLL_CTRL
[7:0]
DLL_TRACK_ DLL_SEARCH_ DLL_SLOPE
ERR
ERR
0x092
DLL_STATUS
[7:0]
RESERVED
0x093
DLL_GB
[7:0]
0x094
DLL_COARSE
[7:0]
0x095
DLL_FINE
[7:0]
RESERVED
DEVSTATUS
Bit 2
Bit 1
Bit 0
Reset RW
ADDRINC
LSBFIRST
SOFTRESET
0x00 R/W
SOFTRESET1
SOFTRESET0
RESERVED
0x00 R/W
CUSTOPMODE
SYSOPMODE
CHIP_TYPE
0x00 R
PROD_GRADE
DEV_REVISION
EN_DATA_
READY
0x00 R
EN_LANE_FIFO EN_PRBSQ
EN_PRBSI
0x00 R/W
IRQ_LANE_
FIFO
IRQ_PRBSI
0x00 R/W
IRQ_PRBSQ
SYNC_LMFC_DELAY_SET_FRM
0x00 R/W
SYNC_LMFC_DELAY_SET[7:0]
0x00 R/W
RESERVED
SYNC_LMFC_DELAY_SET[11:8]
SYNC_LMFC_DELAY_STAT[7:0]
RESERVED
RESERVED
SYSREF_PHASE[11:8]
SPI_
DATAPATH_
PRE
0x00 R/W
SYNC_MODE
RESERVED
TXEN_NCO_ TXEN_
DATAPATH_
RESET
POST
TXEN_
DATAPATH_
PRE
TXEN_DAC_FSC
0xC0 R/W
ANA_DAC_
BIAS_PD1
ANA_DAC_BIAS_
PD0
0x03 R/W
ANA_FULL_SCALE_CURRENT[9:2]
0xFF R/W
CLK_PHASE_TUNE
0x00 R/W
RESERVED
DACCLK_PD
CLK_DUTY_
BOOST_EN
CLK_DUTY_PRG
RESERVED
RESERVED
PLL_REF_CLK_RATE
0x80 R/W
RESERVED
HYS_ON
PLL_REF_CLK_PD
SYSREF_RISE
HYS_CNTRL[9:8]
HYS_CNTRL[7:0]
DLL_FINE_
DC_EN
DLL_FINE_
XC_EN
DLL_COARSE_
DC_EN
DLL_COARSE_
XC_EN
DLL_MODE
DLL_FAIL
RESERVED
DLL_LOST
DLL_GUARD
DLL_COARSE
DLL_FINE
Rev. A | Page 73 of 136
0x00 R/W
0x00 R/W
0x00 R/W
DLL_SEARCH
RESERVED
0x01 R/W
0x80 R/W
CLK_CRS_ADJ
RESERVED
RESERVED
0x00 R/W
ANA_FULL_SCALE_CURRENT[1:0] 0x03 R/W
RESERVED
CLK_DUTY_
OFFSET_EN
0x00 R/W
0x00 R/W
SYSREF_JITTER_WINDOW
RESERVED
SPI_
DATAPATH_
POST
0x00 R/W
0x00 R/W
SYNC_LMFC_DELAY_STAT[11:8]
RESERVED
0x00 R/W
DLL_CLK_PD
0x1F R/W
DLL_ENABLE
0xF0 R/W
DLL_LOCKED
0x00 R/W
0x00 R/W
0x00 R/W
0x80 R/W
AD9164
Data Sheet
Reg.
Name
Bits
Bit 7
Bit 6
Bit 5
0x096
DLL_PHASE
[7:0]
RESERVED
0x097
DLL_BW
[7:0]
RESERVED
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
DLL_PHS
Reset RW
0x08 R/W
DLL_FILT_BW
DLL_WEIGHT
RESERVED
DLL_READ
0x00 R/W
0x098
DLL_READ
[7:0]
0x099
DLL_COARSE_RB
[7:0]
0x09A
DLL_FINE_RB
[7:0]
0x09B
DLL_PHASE_RB
[7:0]
0x09D
DIG_CLK_INVERT
[7:0]
0x0A0
DLL_CLK_DEBUG
[7:0]
0x110
INTERP_MODE
[7:0]
0x111
DATAPATH_CFG
[7:0]
INVSINC_EN
0x113
FTW_UPDATE
[7:0]
RESERVED
0x114
FTW0
[7:0]
FTW[7:0]
0x00 R/W
0x115
FTW1
[7:0]
FTW[15:8]
0x00 R/W
0x116
FTW2
[7:0]
FTW[23:16]
0x00 R/W
0x117
FTW3
[7:0]
FTW[31:24]
0x00 R/W
0x118
FTW4
[7:0]
FTW[39:32]
0x00 R/W
0x119
FTW5
[7:0]
FTW[47:40]
0x00 R/W
0x11C
PHASE_OFFSET0
[7:0]
NCO_PHASE_OFFSET[7:0]
0x00 R/W
0x11D
PHASE_OFFSET1
[7:0]
NCO_PHASE_OFFSET[15:8]
0x00 R/W
0x124
ACC_MODULUS0
[7:0]
ACC_MODULUS[7:0]
0x00 R/W
0x125
ACC_MODULUS1
[7:0]
ACC_MODULUS[15:8]
0x00 R/W
0x126
ACC_MODULUS2
[7:0]
ACC_MODULUS[23:16]
0x00 R/W
0x127
ACC_MODULUS3
[7:0]
ACC_MODULUS[31:24]
0x00 R/W
0x128
ACC_MODULUS4
[7:0]
ACC_MODULUS[39:32]
0x00 R/W
0x129
ACC_MODULUS5
[7:0]
ACC_MODULUS[47:40]
0x00 R/W
0x12A
ACC_DELTA0
[7:0]
ACC_DELTA[7:0]
0x00 R/W
0x12B
ACC_DELTA1
[7:0]
ACC_DELTA[15:8]
0x00 R/W
0x12C
ACC_DELTA2
[7:0]
ACC_DELTA[23:16]
0x00 R/W
RESERVED
DLL_COARSE_RB
DLL_FINE_RB
0x00 R
RESERVED
DLL_PHS_RB
RESERVED
DLL_TEST_EN
INV_DIG_CLK
0x00 R
DIG_CLK_DC_
EN
RESERVED
DIG_CLK_XC_EN
DLL_TEST_DIV
JESD_LANES
NCO_EN
INTERP_MODE
RESERVED
FILT_BW
FTW_REQ_MODE
0x00 R/W
0x00 R
0x03 R/W
0x00 R/W
0x81 R/W
RESERVED
MODULUS_EN
SEL_SIDEBAND FIR85_FILT_EN
0x00 R/W
RESERVED
FTW_LOAD_
SYSREF
FTW_LOAD_
ACK
0x00 R/W
FTW_LOAD_REQ
0x12D
ACC_DELTA3
[7:0]
ACC_DELTA[31:24]
0x00 R/W
0x12E
ACC_DELTA4
[7:0]
ACC_DELTA[39:32]
0x00 R/W
0x12F
ACC_DELTA5
[7:0]
ACC_DELTA[47:40]
0x00 R/W
0x132
TEMP_SENS_LSB
[7:0]
TEMP_SENS_OUT[7:0]
0x133
TEMP_SENS_MSB [7:0]
TEMP_SENS_OUT[15:8]
0x134
TEMP_SENS_
UPDATE
0x135
TEMP_SENS_CTRL [7:0]
TEMP_SENS_
FAST
0x14B
PRBS
[7:0]
PRBS_GOOD_ PRBS_GOOD_I RESERVED
Q
0x14C
PRBS_ERROR_I
[7:0]
PRBS_COUNT_I
0x00 R
0x14D
PRBS_ERROR_Q
[7:0]
PRBS_COUNT_Q
0x00 R
0x14E
TEST_DC_DATA1
[7:0]
DC_TEST_DATA[15:8]
0x00 R/W
0x14F
TEST_DC_DATA0
[7:0]
DC_TEST_DATA[7:0]
0x00 R/W
0x150
DIG_TEST
[7:0]
0x151
DECODE_CTRL
[7:0]
0x152
DECODE_MODE
[7:0]
0x1DF
SPI_STRENGTH
[7:0]
0x200
MASTER_PD
[7:0]
0x201
PHY_PD
[7:0]
[7:0]
R
R
RESERVED
RESERVED
PRBS_INV_Q PRBS_INV_I
PRBS_MODE
RESERVED
PRBS_RESET
SHUFFLE
RESERVED
RESERVED
0x00 R/W
TEMP_SENS_
ENABLE
R/W
PRBS_EN
DC_TEST_EN
RESERVED
TEMP_SENS_
UPDATE
RESERVED
SPI_PD_PHY
Rev. A | Page 74 of 136
0x00 R/W
RESERVED
0x01 R/W
DECODE_MODE
0x00 R/W
SPIDRV
RESERVED
0x10 R/W
0x0F R/W
SPI_PD_MASTER
0x01 R/W
0x00 R/W
Data Sheet
AD9164
Reg.
Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
0x203
GENERIC_PD
[7:0]
0x206
CDR_RESET
[7:0]
0x230
CDR_OPERATING_ [7:0]
MODE_REG_0
0x250
EQ_CONFIG_PHY_ [7:0]
0_1
SPI_EQ_CONFIG1
SPI_EQ_CONFIG0
0x88 R/W
0x251
EQ_CONFIG_PHY_ [7:0]
2_3
SPI_EQ_CONFIG3
SPI_EQ_CONFIG2
0x88 R/W
0x252
EQ_CONFIG_PHY_ [7:0]
4_5
SPI_EQ_CONFIG5
SPI_EQ_CONFIG4
0x88 R/W
0x253
EQ_CONFIG_PHY_ [7:0]
6_7
SPI_EQ_CONFIG7
SPI_EQ_CONFIG6
0x88 R/W
0x268
EQ_BIAS_REG
[7:0]
0x280
SYNTH_ENABLE_
CNTRL
[7:0]
0x281
PLL_STATUS
[7:0]
0x289
REF_CLK_
DIVIDER_LDO
[7:0]
0x2A7
TERM_BLK1_
CTRLREG0
[7:0]
0x2A8
TERM_BLK1_
CTRLREG1
[7:0]
0x2AC
TERM_BLK1_RD_
REG0
[7:0]
0x2AE
TERM_BLK2_
CTRLREG0
[7:0]
0x2AF
TERM_BLK2_
CTRLREG1
[7:0]
0x2B3
TERM_BLK2_RD_
REG0
[7:0]
0x2BB
TERM_OFFSET_0
[7:0]
RESERVED
TERM_OFFSET_0
0x00 R/W
0x2BC
TERM_OFFSET_1
[7:0]
RESERVED
TERM_OFFSET_1
0x00 R/W
RESERVED
SPI_SYNC1_PD RESERVED
RESERVED
RESERVED
SPI_
ENHALFRATE
Bit 0
RESERVED
EQ_POWER_MODE
SPI_DIVISION_RATE
RESERVED
SPI_CP_
OVER_
RANGE_
HIGH_RB
0x01 R/W
RESERVED
0x28 R/W
0x62 R/W
SPI_RECAL_
SYNTH
SPI_CP_
OVER_
RANGE_
LOW_RB
SPI_CP_
CAL_VALID_
RB
RESERVED
RESERVED
RESERVED
SPI_ENABLE_
SYNTH
RESERVED
SPI_I_TUNE_R_
CAL_TERMBLK1
SPI_I_SERIALIZER_RTRIM_TERMBLK1
0x04 R/W
0x00 R/W
0x00 R/W
SPI_O_RCAL_CODE_TERMBLK1
RESERVED
SPI_I_TUNE_R_
CAL_TERMBLK2
SPI_I_SERIALIZER_RTRIM_TERMBLK2
RESERVED
0x00 R/W
SPI_PLL_LOCK_RB 0x00 R
SERDES_PLL_DIV_FACTOR
RESERVED
0x00 R/W
SPI_CDR_RESET
RESERVED
RESERVED
Reset RW
0x00 R
0x00 R/W
0x00 R/W
SPI_O_RCAL_CODE_TERMBLK2
0x00 R
0x2BD
TERM_OFFSET_2
[7:0]
RESERVED
TERM_OFFSET_2
0x00 R/W
0x2BE
TERM_OFFSET_3
[7:0]
RESERVED
TERM_OFFSET_3
0x00 R/W
0x2BF
TERM_OFFSET_4
[7:0]
RESERVED
TERM_OFFSET_4
0x00 R/W
0x2C0
TERM_OFFSET_5
[7:0]
RESERVED
TERM_OFFSET_5
0x00 R/W
0x2C1
TERM_OFFSET_6
[7:0]
RESERVED
TERM_OFFSET_6
0x00 R/W
0x2C2
TERM_OFFSET_7
[7:0]
RESERVED
TERM_OFFSET_7
0x00 R/W
0x300
GENERAL_JRX_
CTRL_0
[7:0]
0x302
DYN_LINK_
LATENCY_0
[7:0]
RESERVED
DYN_LINK_LATENCY_0
0x304
LMFC_DELAY_0
[7:0]
RESERVED
LMFC_DELAY_0
0x306
LMFC_VAR_0
[7:0]
0x308
XBAR_LN_0_1
[7:0]
RESERVED
SRC_LANE1
SRC_LANE0
0x08 R/W
0x309
XBAR_LN_2_3
[7:0]
RESERVED
SRC_LANE3
SRC_LANE2
0x1A R/W
0x30A
XBAR_LN_4_5
[7:0]
RESERVED
SRC_LANE5
SRC_LANE4
0x2C R/W
0x30B
XBAR_LN_6_7
[7:0]
RESERVED
SRC_LANE7
SRC_LANE6
0x3E R/W
0x30C
FIFO_STATUS_
REG_0
[7:0]
LANE_FIFO_FULL
0x00 R
0x30D
FIFO_STATUS_
REG_1
[7:0]
LANE_FIFO_EMPTY
0x00 R
0x311
SYNC_GEN_0
[7:0]
RESERVED
CHECKSUM_
MODE
RESERVED
RESERVED
LINK_EN
0x00 R
0x00 R/W
LMFC_VAR_0
RESERVED
Rev. A | Page 75 of 136
0x00 R/W
0x1F R/W
EOMF_MASK_0 RESERVED
EOF_MASK_0
0x00 R/W
AD9164
Data Sheet
Reg.
Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
0x312
SYNC_GEN_1
[7:0]
0x313
SYNC_GEN_3
[7:0]
LMFC_PERIOD
0x00 R
0x315
PHY_PRBS_TEST_ [7:0]
EN
PHY_TEST_EN
0x00 R/W
0x316
PHY_PRBS_TEST_ [7:0]
CTRL
0x317
PHY_PRBS_TEST_ [7:0]
THRESHOLD_
LOBITS
PHY_PRBS_THRESHOLD_LOBITS
0x00 R/W
0x318
PHY_PRBS_TEST_ [7:0]
THRESHOLD_
MIDBITS
PHY_PRBS_THRESHOLD_MIDBITS
0x00 R/W
0x319
PHY_PRBS_TEST_ [7:0]
THRESHOLD_
HIBITS
PHY_PRBS_THRESHOLD_HIBITS
0x00 R/W
0x31A
PHY_PRBS_TEST_ [7:0]
ERRCNT_LOBITS
PHY_PRBS_ERR_CNT_LOBITS
0x00 R
0x31B
PHY_PRBS_TEST_ [7:0]
ERRCNT_MIDBITS
PHY_PRBS_ERR_CNT_MIDBITS
0x00 R
0x31C
PHY_PRBS_TEST_ [7:0]
ERRCNT_HIBITS
PHY_PRBS_ERR_CNT_HIBITS
0x00 R
0x31D
PHY_PRBS_TEST_ [7:0]
STATUS
PHY_PRBS_PASS
0xFF R
0x31E
PHY_DATA_
SNAPSHOT_CTRL
0x31F
PHY_SNAPSHOT_ [7:0]
DATA_BYTE0
PHY_SNAPSHOT_DATA_BYTE0
0x00 R
0x320
PHY_SNAPSHOT_ [7:0]
DATA_BYTE1
PHY_SNAPSHOT_DATA_BYTE1
0x00 R
0x321
PHY_SNAPSHOT_ [7:0]
DATA_BYTE2
PHY_SNAPSHOT_DATA_BYTE2
0x00 R
0x322
PHY_SNAPSHOT_ [7:0]
DATA_BYTE3
PHY_SNAPSHOT_DATA_BYTE3
0x00 R
0x323
PHY_SNAPSHOT_ [7:0]
DATA_BYTE4
PHY_SNAPSHOT_DATA_BYTE4
0x00 R
0x32C
SHORT_TPL_
TEST_0
[7:0]
0x32D
SHORT_TPL_
TEST_1
[7:0]
SHORT_TPL_REF_SP_LSB
0x00 R/W
0x32E
SHORT_TPL_
TEST_2
[7:0]
SHORT_TPL_REF_SP_MSB
0x00 R/W
0x32F
SHORT_TPL_
TEST_3
[7:0]
0x334
JESD_BIT_
INVERSE_CTRL
[7:0]
JESD_BIT_INVERSE
0x400
DID_REG
[7:0]
DID_RD
0x00 R
0x401
BID_REG
[7:0]
BID_RD
0x00 R
0x402
LID0_REG
[7:0]
RESERVED
0x403
SCR_L_REG
[7:0]
SCR_RD
0x404
F_REG
[7:0]
0x405
K_REG
[7:0]
0x406
M_REG
[7:0]
0x407
CS_N_REG
[7:0]
0x408
NP_REG
[7:0]
0x409
S_REG
[7:0]
0x40A
HD_CF_REG
[7:0]
SYNC_ERR_DUR
RESERVED
[7:0]
Bit 1
PHY_PRBS_PAT_SEL
RESERVED
PHY_TEST_
START
PHY_GRAB_LANE_SEL
SHORT_TPL_SP_SEL
PHY_GRAB_
MODE
SHORT_TPL_M_SEL
RESERVED
PHADJ_RD
RESERVED
PHY_GRAB_DATA 0x00 R/W
SHORT_TPL_TEST_ 0x00 R/W
EN
0x00 R
LL_LID0
0x00 R
L_RD
0x00 R
0x00 R
K_RD
M_RD
RESERVED
0x00 R/W
0x00 R/W
F_RD
HD_RD
PHY_TEST_RESET
SHORT_TPL_FAIL
RESERVED
CS_RD
SHORT_TPL_
TEST_RESET
Reset RW
0x00 R/W
SYNC_SYNCREQ_DUR
PHY_SRC_ERR_CNT
ADJDIR_RD
Bit 0
0x00 R
0x00 R
N_RD
0x00 R
SUBCLASSV_RD
NP_RD
0x00 R
JESDV_RD
S_RD
0x00 R
CF_RD
0x00 R
RESERVED
0x40B
RES1_REG
[7:0]
RES1_RD
0x00 R
0x40C
RES2_REG
[7:0]
RES2_RD
0x00 R
Rev. A | Page 76 of 136
Data Sheet
Reg.
Name
AD9164
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset RW
0x40D
CHECKSUM0_REG [7:0]
LL_FCHK0
0x00 R
0x40E
COMPSUM0_REG
[7:0]
LL_FCMP0
0x00 R
0x412
LID1_REG
[7:0]
0x415
CHECKSUM1_REG [7:0]
LL_FCHK1
0x00 R
0x416
COMPSUM1_REG
[7:0]
LL_FCMP1
0x00 R
0x41A
LID2_REG
[7:0]
0x41D
CHECKSUM2_REG [7:0]
LL_FCHK2
0x00 R
0x41E
COMPSUM2_REG
[7:0]
LL_FCMP2
0x00 R
0x422
LID3_REG
[7:0]
0x425
CHECKSUM3_REG [7:0]
LL_FCHK3
0x00 R
0x426
COMPSUM3_REG
[7:0]
LL_FCMP3
0x00 R
0x42A
LID4_REG
[7:0]
0x42D
CHECKSUM4_REG [7:0]
LL_FCHK4
0x00 R
0x42E
COMPSUM4_REG
[7:0]
LL_FCMP4
0x00 R
0x432
LID5_REG
[7:0]
0x435
CHECKSUM5_REG [7:0]
0x436
COMPSUM5_REG
[7:0]
0x43A
LID6_REG
[7:0]
0x43D
CHECKSUM6_REG [7:0]
0x43E
COMPSUM6_REG
[7:0]
0x442
LID7_REG
[7:0]
0x445
CHECKSUM7_REG [7:0]
LL_FCHK7
0x00 R
0x446
COMPSUM7_REG
[7:0]
LL_FCMP7
0x00 R
0x450
ILS_DID
[7:0]
DID
0x00 R/W
0x451
ILS_BID
[7:0]
BID
0x00 R/W
0x452
ILS_LID0
[7:0]
RESERVED
0x453
ILS_SCR_L
[7:0]
SCR
0x454
ILS_F
[7:0]
0x455
ILS_K
[7:0]
0x456
ILS_M
[7:0]
0x457
ILS_CS_N
[7:0]
0x458
ILS_NP
[7:0]
SUBCLASSV
NP
0x0F R/W
0x459
ILS_S
[7:0]
JESDV
S
0x01 R/W
0x45A
ILS_HD_CF
[7:0]
CF
0x80 R
0x45B
ILS_RES1
[7:0]
RES1
0x00 R/W
0x45C
ILS_RES2
[7:0]
RES2
0x00 R/W
RESERVED
LL_LID1
RESERVED
0x00 R
LL_LID2
RESERVED
0x00 R
LL_LID3
RESERVED
0x00 R
LL_LID4
RESERVED
0x00 R
LL_LID5
0x00 R
LL_FCHK5
0x00 R
LL_FCMP5
0x00 R
RESERVED
LL_LID6
0x00 R
LL_FCHK6
0x00 R
LL_FCMP6
0x00 R
RESERVED
ADJDIR
LL_LID7
PHADJ
RESERVED
0x00 R
LID0
0x00 R/W
L
0x87 R/W
F
0x00 R
RESERVED
K
0x1F R/W
M
CS
0x01 R
RESERVED
HD
N
RESERVED
0x0F R
0x45D
ILS_CHECKSUM
[7:0]
0x46C
LANE_DESKEW
[7:0]
ILD7
ILS6
ILD5
ILD4
FCHK0
ILD3
ILD2
ILD1
ILD0
0x00 R
0x46D
BAD_DISPARITY
[7:0]
BDE7
BDE6
BDE5
BDE4
BDE3
BDE2
BDE1
BDE0
0x00 R
0x46E
NOT_IN_TABLE
[7:0]
NIT7
NIT6
NIT5
NIT4
NIT3
NIT2
NIT1
NIT0
0x00 R
0x46F
UNEXPECTED_
KCHAR
[7:0]
UEK7
UEK6
UEK5
UEK4
UEK3
UEK2
UEK1
UEK0
0x00 R
0x470
CODE_GRP_SYNC [7:0]
CGS7
CGS6
CGS5
CGS4
CGS3
CGS2
CGS1
CGS0
0x00 R
0x471
FRAME_SYNC
[7:0]
FS7
FS6
FS5
FS4
FS3
FS2
FS1
FS0
0x00 R
0x472
GOOD_
CHECKSUM
[7:0]
CKS7
CKS6
CKS5
CKS4
CKS3
CKS2
CKS1
CKS0
0x00 R
0x473
INIT_LANE_SYNC
[7:0]
ILS7
ILS6
ILS5
ILS4
ILS3
ILS2
ILS1
ILS0
0x00 R
0x475
CTRLREG0
[7:0]
RX_DIS
CHAR_REPL_
DIS
SOFTRST
FORCESYNCREQ RESERVED
REPL_FRM_ENA
0x01 R/W
0x476
CTRLREG1
[7:0]
CGS_SEL
FCHK_N
0x14 R/W
RESERVED
RESERVED
QUAL_RDERR DEL_SCR
Rev. A | Page 77 of 136
0x00 R/W
NO_ILAS
AD9164
Data Sheet
Reg.
Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
0x477
CTRLREG2
[7:0]
ILS_MODE
RESERVED
REPDATATEST QUETESTERR AR_ECNTR
0x478
KVAL
[7:0]
0x47C
ERRORTHRES
[7:0]
0x47D
SYNC_ASSERT_
MASK
[7:0]
0x480
ECNT_CTRL0
[7:0]
RESERVED
0x481
ECNT_CTRL1
[7:0]
0x482
ECNT_CTRL2
[7:0]
0x483
ECNT_CTRL3
0x484
0x485
Bit 2
Bit 1
Bit 0
RESERVED
Reset RW
0x00 R/W
KSYNC
0x01 R/W
ETH
0xFF R/W
RESERVED
SYNC_ASSERT_MASK
0x07 R/W
ECNT_ENA0
ECNT_RST0
0x3F R/W
RESERVED
ECNT_ENA1
ECNT_RST1
0x3F R/W
RESERVED
ECNT_ENA2
ECNT_RST2
0x3F R/W
[7:0]
RESERVED
ECNT_ENA3
ECNT_RST3
0x3F R/W
ECNT_CTRL4
[7:0]
RESERVED
ECNT_ENA4
ECNT_RST4
0x3F R/W
ECNT_CTRL5
[7:0]
RESERVED
ECNT_ENA5
ECNT_RST5
0x3F R/W
0x486
ECNT_CTRL6
[7:0]
RESERVED
ECNT_ENA6
ECNT_RST6
0x3F R/W
0x487
ECNT_CTRL7
[7:0]
RESERVED
ECNT_RST7
0x3F R/W
0x488
ECNT_TCH0
[7:0]
RESERVED
ECNT_TCH0
0x07 R/W
0x489
ECNT_TCH1
[7:0]
RESERVED
ECNT_TCH1
0x07 R/W
0x48A
ECNT_TCH2
[7:0]
RESERVED
ECNT_TCH2
0x07 R/W
0x48B
ECNT_TCH3
[7:0]
RESERVED
ECNT_TCH3
0x07 R/W
0x48C
ECNT_TCH4
[7:0]
RESERVED
ECNT_TCH4
0x07 R/W
0x48D
ECNT_TCH5
[7:0]
RESERVED
ECNT_TCH5
0x07 R/W
0x48E
ECNT_TCH6
[7:0]
RESERVED
ECNT_TCH6
0x07 R/W
ECNT_ENA7
0x48F
ECNT_TCH7
[7:0]
ECNT_TCH7
0x07 R/W
0x490
ECNT_STAT0
[7:0]
RESERVED
RESERVED
LANE_ENA0
ECNT_TCR0
0x00 R
0x491
ECNT_STAT1
[7:0]
RESERVED
LANE_ENA1
ECNT_TCR1
0x00 R
0x492
ECNT_STAT2
[7:0]
RESERVED
LANE_ENA2
ECNT_TCR2
0x00 R
0x493
ECNT_STAT3
[7:0]
RESERVED
LANE_ENA3
ECNT_TCR3
0x00 R
0x494
ECNT_STAT4
[7:0]
RESERVED
LANE_ENA4
ECNT_TCR4
0x00 R
0x495
ECNT_STAT5
[7:0]
RESERVED
LANE_ENA5
ECNT_TCR5
0x00 R
0x496
ECNT_STAT6
[7:0]
RESERVED
LANE_ENA6
ECNT_TCR6
0x00 R
0x497
ECNT_STAT7
[7:0]
RESERVED
LANE_ENA7
ECNT_TCR7
0x00 R
0x4B0
LINK_STATUS0
[7:0]
BDE0
NIT0
UEK0
ILD0
ILS0
CKS0
FS0
CGS0
0x00 R
0x4B1
LINK_STATUS1
[7:0]
BDE1
NIT1
UEK1
ILD1
ILS1
CKS1
FS1
CGS1
0x00 R
0x4B2
LINK_STATUS2
[7:0]
BDE2
NIT2
UEK2
ILD2
ILS2
CKS2
FS2
CGS2
0x00 R
0x4B3
LINK_STATUS3
[7:0]
BDE3
NIT3
UEK3
ILD3
ILS3
CKS3
FS3
CGS3
0x00 R
0x4B4
LINK_STATUS4
[7:0]
BDE4
NIT4
UEK4
ILD4
ILS4
CKS4
FS4
CGS4
0x00 R
0x4B5
LINK_STATUS5
[7:0]
BDE5
NIT5
UEK5
ILD5
ILS5
CKS5
FS5
CGS5
0x00 R
0x4B6
LINK_STATUS6
[7:0]
BDE6
NIT6
UEK6
ILD6
ILS6
CKS6
FS6
CGS6
0x00 R
0x4B7
LINK_STATUS7
[7:0]
BDE7
NIT7
UEK7
ILD7
ILS7
CKS7
FS7
CGS7
0x00 R
0x4B8
JESD_IRQ_
ENABLEA
[7:0]
EN_BDE
EN_NIT
EN_UEK
EN_ILD
EN_ILS
EN_CKS
EN_FS
EN_CGS
0x00 R/W
0x4B9
JESD_IRQ_
ENABLEB
[7:0]
EN_ILAS
0x00 R/W
0x4BA
JESD_IRQ_
STATUSA
[7:0]
IRQ_CGS
0x00 R/W
0x4BB
JESD_IRQ_
STATUSB
[7:0]
IRQ_ILAS
0x00 R/W
0x800
HOPF_CTRL
[7:0]
0x806
HOPF_FTW1_0
[7:0]
0x807
HOPF_FTW1_1
0x808
HOPF_FTW1_2
0x809
HOPF_FTW1_3
RESERVED
IRQ_BDE
IRQ_NIT
IRQ_UEK
IRQ_ILD
IRQ_ILS
IRQ_CKS
IRQ_FS
RESERVED
HOPF_MODE
RESERVED
HOPF_SEL
0x00 R/W
HOPF_FTW1[7:0]
0x00 R/W
[7:0]
HOPF_FTW1[15:8]
0x00 R/W
[7:0]
HOPF_FTW1[23:16]
0x00 R/W
[7:0]
HOPF_FTW1[31:24]
0x00 R/W
Rev. A | Page 78 of 136
Data Sheet
Reg.
AD9164
Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset RW
0x80A
HOPF_FTW2_0
[7:0]
HOPF_FTW2[7:0]
0x00 R/W
0x80B
HOPF_FTW2_1
[7:0]
HOPF_FTW2[15:8]
0x00 R/W
0x80C
HOPF_FTW2_2
[7:0]
HOPF_FTW2[23:16]
0x00 R/W
0x80D
HOPF_FTW2_3
[7:0]
HOPF_FTW2[31:24]
0x00 R/W
0x80E
HOPF_FTW3_0
[7:0]
HOPF_FTW3[7:0]
0x00 R/W
0x80F
HOPF_FTW3_1
[7:0]
HOPF_FTW3[15:8]
0x00 R/W
0x810
HOPF_FTW3_2
[7:0]
HOPF_FTW3[23:16]
0x00 R/W
0x811
HOPF_FTW3_3
[7:0]
HOPF_FTW3[31:24]
0x00 R/W
0x812
HOPF_FTW4_0
[7:0]
HOPF_FTW4[7:0]
0x00 R/W
0x813
HOPF_FTW4_1
[7:0]
HOPF_FTW4[15:8]
0x00 R/W
0x814
HOPF_FTW4_2
[7:0]
HOPF_FTW4[23:16]
0x00 R/W
0x815
HOPF_FTW4_3
[7:0]
HOPF_FTW4[31:24]
0x00 R/W
0x816
HOPF_FTW5_0
[7:0]
HOPF_FTW5[7:0]
0x00 R/W
0x817
HOPF_FTW5_1
[7:0]
HOPF_FTW5[15:8]
0x00 R/W
0x818
HOPF_FTW5_2
[7:0]
HOPF_FTW5[23:16]
0x00 R/W
0x819
HOPF_FTW5_3
[7:0]
HOPF_FTW5[31:24]
0x00 R/W
0x81A
HOPF_FTW6_0
[7:0]
HOPF_FTW6[7:0]
0x00 R/W
0x81B
HOPF_FTW6_1
[7:0]
HOPF_FTW6[15:8]
0x00 R/W
0x81C
HOPF_FTW6_2
[7:0]
HOPF_FTW6[23:16]
0x00 R/W
0x81D
HOPF_FTW6_3
[7:0]
HOPF_FTW6[31:24]
0x00 R/W
0x81E
HOPF_FTW7_0
[7:0]
HOPF_FTW7[7:0]
0x00 R/W
0x81F
HOPF_FTW7_1
[7:0]
HOPF_FTW7[15:8]
0x00 R/W
0x820
HOPF_FTW7_2
[7:0]
HOPF_FTW7[23:16]
0x00 R/W
0x821
HOPF_FTW7_3
[7:0]
HOPF_FTW7[31:24]
0x00 R/W
0x822
HOPF_FTW8_0
[7:0]
HOPF_FTW8[7:0]
0x00 R/W
0x823
HOPF_FTW8_1
[7:0]
HOPF_FTW8[15:8]
0x00 R/W
0x824
HOPF_FTW8_2
[7:0]
HOPF_FTW8[23:16]
0x00 R/W
0x825
HOPF_FTW8_3
[7:0]
HOPF_FTW8[31:24]
0x00 R/W
0x826
HOPF_FTW9_0
[7:0]
HOPF_FTW9[7:0]
0x00 R/W
0x827
HOPF_FTW9_1
[7:0]
HOPF_FTW9[15:8]
0x00 R/W
0x828
HOPF_FTW9_2
[7:0]
HOPF_FTW9[23:16]
0x00 R/W
0x829
HOPF_FTW9_3
[7:0]
HOPF_FTW9[31:24]
0x00 R/W
0x82A
HOPF_FTW10_0
[7:0]
HOPF_FTW10[7:0]
0x00 R/W
0x82B
HOPF_FTW10_1
[7:0]
HOPF_FTW10[15:8]
0x00 R/W
0x82C
HOPF_FTW10_2
[7:0]
HOPF_FTW10[23:16]
0x00 R/W
0x82D
HOPF_FTW10_3
[7:0]
HOPF_FTW10[31:24]
0x00 R/W
0x82E
HOPF_FTW11_0
[7:0]
HOPF_FTW11[7:0]
0x00 R/W
0x82F
HOPF_FTW11_1
[7:0]
HOPF_FTW11[15:8]
0x00 R/W
0x830
HOPF_FTW11_2
[7:0]
HOPF_FTW11[23:16]
0x00 R/W
0x831
HOPF_FTW11_3
[7:0]
HOPF_FTW11[31:24]
0x00 R/W
0x832
HOPF_FTW12_0
[7:0]
HOPF_FTW12[7:0]
0x00 R/W
0x833
HOPF_FTW12_1
[7:0]
HOPF_FTW12[15:8]
0x00 R/W
0x834
HOPF_FTW12_2
[7:0]
HOPF_FTW12[23:16]
0x00 R/W
0x835
HOPF_FTW12_3
[7:0]
HOPF_FTW12[31:24]
0x00 R/W
0x836
HOPF_FTW13_0
[7:0]
HOPF_FTW13[7:0]
0x00 R/W
0x837
HOPF_FTW13_1
[7:0]
HOPF_FTW13[15:8]
0x00 R/W
0x838
HOPF_FTW13_2
[7:0]
HOPF_FTW13[23:16]
0x00 R/W
0x839
HOPF_FTW13_3
[7:0]
HOPF_FTW13[31:24]
0x00 R/W
Rev. A | Page 79 of 136
AD9164
Reg.
Data Sheet
Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset RW
0x83A
HOPF_FTW14_0
[7:0]
HOPF_FTW14[7:0]
0x00 R/W
0x83B
HOPF_FTW14_1
[7:0]
HOPF_FTW14[15:8]
0x00 R/W
0x83C
HOPF_FTW14_2
[7:0]
HOPF_FTW14[23:16]
0x00 R/W
0x83D
HOPF_FTW14_3
[7:0]
HOPF_FTW14[31:24]
0x00 R/W
0x83E
HOPF_FTW15_0
[7:0]
HOPF_FTW15[7:0]
0x00 R/W
0x83F
HOPF_FTW15_1
[7:0]
HOPF_FTW15[15:8]
0x00 R/W
0x840
HOPF_FTW15_2
[7:0]
HOPF_FTW15[23:16]
0x00 R/W
0x841
HOPF_FTW15_3
[7:0]
HOPF_FTW15[31:24]
0x00 R/W
0x842
HOPF_FTW16_0
[7:0]
HOPF_FTW16[7:0]
0x00 R/W
0x843
HOPF_FTW16_1
[7:0]
HOPF_FTW16[15:8]
0x00 R/W
0x844
HOPF_FTW16_2
[7:0]
HOPF_FTW16[23:16]
0x00 R/W
0x845
HOPF_FTW16_3
[7:0]
HOPF_FTW16[31:24]
0x00 R/W
0x846
HOPF_FTW17_0
[7:0]
HOPF_FTW17[7:0]
0x00 R/W
0x847
HOPF_FTW17_1
[7:0]
HOPF_FTW17[15:8]
0x00 R/W
0x848
HOPF_FTW17_2
[7:0]
HOPF_FTW17[23:16]
0x00 R/W
0x849
HOPF_FTW17_3
[7:0]
HOPF_FTW17[31:24]
0x00 R/W
0x84A
HOPF_FTW18_0
[7:0]
HOPF_FTW18[7:0]
0x00 R/W
0x84B
HOPF_FTW18_1
[7:0]
HOPF_FTW18[15:8]
0x00 R/W
0x84C
HOPF_FTW18_2
[7:0]
HOPF_FTW18[23:16]
0x00 R/W
0x00 R/W
0x84D
HOPF_FTW18_3
[7:0]
HOPF_FTW18[31:24]
0x84E
HOPF_FTW19_0
[7:0]
HOPF_FTW19[7:0]
0x00 R/W
0x84F
HOPF_FTW19_1
[7:0]
HOPF_FTW19[15:8]
0x00 R/W
0x850
HOPF_FTW19_2
[7:0]
HOPF_FTW19[23:16]
0x00 R/W
0x851
HOPF_FTW19_3
[7:0]
HOPF_FTW19[31:24]
0x00 R/W
0x852
HOPF_FTW20_0
[7:0]
HOPF_FTW20[7:0]
0x00 R/W
0x853
HOPF_FTW20_1
[7:0]
HOPF_FTW20[15:8]
0x00 R/W
0x854
HOPF_FTW20_2
[7:0]
HOPF_FTW20[23:16]
0x00 R/W
0x855
HOPF_FTW20_3
[7:0]
HOPF_FTW20[31:24]
0x00 R/W
0x856
HOPF_FTW21_0
[7:0]
HOPF_FTW21[7:0]
0x00 R/W
0x857
HOPF_FTW21_1
[7:0]
HOPF_FTW21[15:8]
0x00 R/W
0x858
HOPF_FTW21_2
[7:0]
HOPF_FTW21[23:16]
0x00 R/W
0x859
HOPF_FTW21_3
[7:0]
HOPF_FTW21[31:24]
0x00 R/W
0x85A
HOPF_FTW22_0
[7:0]
HOPF_FTW22[7:0]
0x00 R/W
0x85B
HOPF_FTW22_1
[7:0]
HOPF_FTW22[15:8]
0x00 R/W
0x85C
HOPF_FTW22_2
[7:0]
HOPF_FTW22[23:16]
0x00 R/W
0x85D
HOPF_FTW22_3
[7:0]
HOPF_FTW22[31:24]
0x00 R/W
0x85E
HOPF_FTW23_0
[7:0]
HOPF_FTW23[7:0]
0x00 R/W
0x85F
HOPF_FTW23_1
[7:0]
HOPF_FTW23[15:8]
0x00 R/W
0x860
HOPF_FTW23_2
[7:0]
HOPF_FTW23[23:16]
0x00 R/W
0x861
HOPF_FTW23_3
[7:0]
HOPF_FTW23[31:24]
0x00 R/W
0x862
HOPF_FTW24_0
[7:0]
HOPF_FTW24[7:0]
0x00 R/W
0x863
HOPF_FTW24_1
[7:0]
HOPF_FTW24[15:8]
0x00 R/W
0x864
HOPF_FTW24_2
[7:0]
HOPF_FTW24[23:16]
0x00 R/W
0x865
HOPF_FTW24_3
[7:0]
HOPF_FTW24[31:24]
0x00 R/W
0x866
HOPF_FTW25_0
[7:0]
HOPF_FTW25[7:0]
0x00 R/W
0x867
HOPF_FTW25_1
[7:0]
HOPF_FTW25[15:8]
0x00 R/W
0x868
HOPF_FTW25_2
[7:0]
HOPF_FTW25[23:16]
0x00 R/W
0x869
HOPF_FTW25_3
[7:0]
HOPF_FTW25[31:24]
0x00 R/W
Rev. A | Page 80 of 136
Data Sheet
Reg.
AD9164
Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset RW
0x86A
HOPF_FTW26_0
[7:0]
HOPF_FTW26[7:0]
0x00 R/W
0x86B
HOPF_FTW26_1
[7:0]
HOPF_FTW26[15:8]
0x00 R/W
0x86C
HOPF_FTW26_2
[7:0]
HOPF_FTW26[23:16]
0x00 R/W
0x86D
HOPF_FTW26_3
[7:0]
HOPF_FTW26[31:24]
0x00 R/W
0x86E
HOPF_FTW27_0
[7:0]
HOPF_FTW27[7:0]
0x00 R/W
0x86F
HOPF_FTW27_1
[7:0]
HOPF_FTW27[15:8]
0x00 R/W
0x870
HOPF_FTW27_2
[7:0]
HOPF_FTW27[23:16]
0x00 R/W
0x871
HOPF_FTW27_3
[7:0]
HOPF_FTW27[31:24]
0x00 R/W
0x872
HOPF_FTW28_0
[7:0]
HOPF_FTW28[7:0]
0x00 R/W
0x873
HOPF_FTW28_1
[7:0]
HOPF_FTW28[15:8]
0x00 R/W
0x874
HOPF_FTW28_2
[7:0]
HOPF_FTW28[23:16]
0x00 R/W
0x875
HOPF_FTW28_3
[7:0]
HOPF_FTW28[31:24]
0x00 R/W
0x876
HOPF_FTW29_0
[7:0]
HOPF_FTW29[7:0]
0x00 R/W
0x877
HOPF_FTW29_1
[7:0]
HOPF_FTW29[15:8]
0x00 R/W
0x878
HOPF_FTW29_2
[7:0]
HOPF_FTW29[23:16]
0x00 R/W
0x879
HOPF_FTW29_3
[7:0]
HOPF_FTW29[31:24]
0x00 R/W
0x87A
HOPF_FTW30_0
[7:0]
HOPF_FTW30[7:0]
0x00 R/W
0x87B
HOPF_FTW30_1
[7:0]
HOPF_FTW30[15:8]
0x00 R/W
0x87C
HOPF_FTW30_2
[7:0]
HOPF_FTW30[23:16]
0x00 R/W
0x00 R/W
0x87D
HOPF_FTW30_3
[7:0]
HOPF_FTW30[31:24]
0x87E
HOPF_FTW31_0
[7:0]
HOPF_FTW31[7:0]
0x00 R/W
0x87F
HOPF_FTW31_1
[7:0]
HOPF_FTW31[15:8]
0x00 R/W
0x880
HOPF_FTW31_2
[7:0]
HOPF_FTW31[23:16]
0x00 R/W
0x881
HOPF_FTW31_3
[7:0]
HOPF_FTW31[31:24]
0x00 R/W
Rev. A | Page 81 of 136
AD9164
Data Sheet
REGISTER DETAILS
Table 46. Register Details
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x000 SPI_INTFCONFA
7
SOFTRESET_M
Soft reset (mirror). Set this to
mirror Bit 0.
0x0
R
6
LSBFIRST_M
LSB first (mirror). Set this to
mirror Bit 1.
0x0
R
5
ADDRINC_M
Address increment (mirror). Set
this to mirror Bit 2.
0x0
R
4
SDOACTIVE_M
SDO active (mirror). Set this to
mirror Bit 3.
0x0
R
3
SDOACTIVE
SDO active. Enables 4-wire SPI
bus mode.
0x0
R/W
2
ADDRINC
0x0
R/W
1
LSBFIRST
LSB first. When set, causes input 0x0
and output data to be oriented
as LSB first. If this bit is clear, data
is oriented as MSB first.
R/W
Settings
Address increment. When set,
causes incrementing streaming
addresses; otherwise,
descending addresses are
generated.
1 Streaming addresses are
incremented.
0 Streaming addresses are
decremented.
1 Shift LSB in first.
0 Shift MSB in first.
0x001 SPI_INTFCONFB
0
SOFTRESET
Soft reset. This bit automatically
clears to 0 after performing a
reset operation. Setting this bit
initiates a reset. This bit is
autoclearing after the soft reset
is complete.
1 Pulse the soft reset line.
0 Reset the soft reset line.
0x0
R/W
7
SINGLEINS
Single instruction.
1 Perform single transfers.
0x0
R/W
6
CSSTALL
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R
0 Perform multiple transfers.
CS stalling.
0 Disable CS stalling.
1 Enable CS stalling.
[5:3] RESERVED
Reserved.
2
SOFTRESET1
1
SOFTRESET0
0
RESERVED
Soft Reset 1. This bit
automatically clears to 0 after
performing a reset operation.
1 Pulse the Soft Reset 1 line.
0 Pulse the Soft Reset 1 line.
Soft Reset 0. This bit
automatically clears to 0 after
performing a reset operation.
1 Pulse the Soft Reset 0 line.
0 Pulse the Soft Reset 0 line.
Reserved.
Rev. A | Page 82 of 136
Data Sheet
AD9164
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x002 SPI_DEVCONF
[7:4] DEVSTATUS
Device status.
0x0
R/W
[3:2] CUSTOPMODE
[1:0] SYSOPMODE
Customer operating mode.
System operating mode.
0x0
0x0
R/W
R/W
Settings
0 Normal operation.
1 Low power operation.
2 Medium power standby.
3 Low power sleep.
0x003 SPI_CHIPTYPE
[7:0] CHIP_TYPE
Chip type.
0x0
R
0x004 SPI_PRODIDL
[7:0] PROD_ID[7:0]
Product ID.
0x0
R
0x005 SPI_PRODIDH
[7:0] PROD_ID[15:8]
Product ID.
0x0
R
0x006 SPI_CHIPGRADE
[7:4] PROD_GRADE
Product grade.
0x0
R
[3:0] DEV_REVISION
Device revision.
0x0
R
[7:5] RESERVED
Reserved.
0x0
R
4
Enable SYSREF± jitter interrupt.
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x020 IRQ_ENABLE
EN_SYSREF_JITTER
0 Disable interrupt.
1 Enable interrupt.
3
EN_DATA_READY
Enable JESD204x receiver ready
(JRX_DATA_READY) low
interrupt.
0 Disable interrupt.
1 Enable interrupt.
2
EN_LANE_FIFO
Enable lane FIFO overflow/
underflow interrupt.
0 Disable interrupt.
1 Enable interrupt.
1
EN_PRBSQ
0
EN_PRBSI
Enable PRBS imaginary error
interrupt.
0 Disable interrupt.
1 Enable interrupt.
Enable PRBS real error interrupt.
0 Disable interrupt.
1 Enable interrupt.
0x024 IRQ_STATUS
[7:5] RESERVED
Reserved.
0x0
R
4
IRQ_SYSREF_JITTER
SYSREF± jitter is too big. Writing
1 clears the status.
0x0
R/W
3
IRQ_DATA_READY
JRX_DATA_READY is low. Writing 0x0
1 clears the status.
R/W
0 No warning.
1 Warning detected.
2
IRQ_LANE_FIFO
1
IRQ_PRBSQ
0
IRQ_PRBSI
Lane FIFO overflow/underflow.
Writing 1 clears the status.
0 No warning.
0x0
R/W
PRBS imaginary error. Writing 1
clears the status.
0 No warning.
1 Warning detected.
0x0
R/W
PRBS real error. Writing 1 clears
the status.
0x0
R/W
0x0
R
1 Warning detected.
0 No warning.
1 Warning detected.
0x031 SYNC_LMFC_DELAY_FRAME
[7:5] RESERVED
Reserved.
[4:0] SYNC_LMFC_DELAY_SET_FRM
Desired delay from rising edge of 0x0
SYSREF± input to rising edge of
LMFC in frames.
Rev. A | Page 83 of 136
R/W
AD9164
Data Sheet
Hex.
Addr. Name
Bits Bit Name
0x032 SYNC_LMFC_DELAY0
[7:0] SYNC_LMFC_DELAY_SET[7:0]
Desired delay from rising edge of 0x0
SYSREF± input to rising edge of
LMFC in DAC clock units.
R/W
0x033 SYNC_LMFC_DELAY1
[7:4] RESERVED
Reserved.
R
[3:0] SYNC_LMFC_DELAY_SET[11:8]
Desired delay from rising edge of 0x0
SYSREF± input to rising edge of
LMFC in DAC clock units.
R/W
0x034 SYNC_LMFC_STAT0
[7:0] SYNC_LMFC_DELAY_STAT[7:0]
Measured delay from rising edge 0x0
of SYSREF± input to rising edge
of LMFC in DAC clock units (note:
2 LSBs are always zero). A write
to SYNC_LMFC_STATx or
SYSREF_PHASEx saves the data for
readback.
R/W
0x035 SYNC_LMFC_STAT1
[7:4] RESERVED
Reserved.
R
[3:0] SYNC_LMFC_DELAY_STAT[11:8]
Measured delay from rising edge 0x0
of SYSREF± input to rising edge
of LMFC in DAC clock units (note:
2 LSBs are always zero). A write
to SYNC_LMFC_STATx or
SYSREF_PHASEx saves the data for
readback.
R/W
0x036 SYSREF_COUNT
[7:0] SYSREF_COUNT
Count of SYSREF± signals received. 0x0
A write resets the count. A write
to SYNC_LMFC_STATx or
SYSREF_PHASEx saves the data for
readback.
R/W
0x037 SYSREF_PHASE0
[7:0] SYSREF_PHASE[7:0]
Phase of measured SYSREF±
event. Thermometer encoded. A
write to SYNC_LMFC_STATx or
SYSREF_PHASEx saves the data
for readback.
0x0
R/W
0x038 SYSREF_PHASE1
[7:4] RESERVED
Reserved.
0x0
R
[3:0] SYSREF_PHASE[11:8]
Phase of measured SYSREF±
event. Thermometer encoded. A
write to SYNC_LMFC_STATx or
SYSREF_PHASEx saves the data
for readback.
0x0
R/W
[7:6] RESERVED
Reserved.
0x0
R
[5:0] SYSREF_JITTER_WINDOW
Amount of jitter allowed on the
SYSREF± input. SYSREF± jitter
variations bigger than this
triggers an interrupt. Units are in
DAC clocks. The bottom two bits
are ignored.
0x0
R/W
[7:2] RESERVED
Reserved.
0x0
R
0x0
R/W
0x039 SYSREF_JITTER_WINDOW
0x03A SYNC_CTRL
Settings
[1:0] SYNC_MODE
Description
Synchronization mode.
00 Do not perform synchronization,
monitor SYSREF± to LMFC delay
only.
01 Perform continuous synchronization of LMFC on every SYSREF±.
10 Perform a single synchronization
on the next SYSREF±, then
switch to monitor mode.
Rev. A | Page 84 of 136
Reset Access
0x0
0x0
Data Sheet
AD9164
Hex.
Addr. Name
Bits Bit Name
0x03F TX_ENABLE
7
SPI_DATAPATH_POST
6
SPI_DATAPATH_PRE
Settings
Description
Reset Access
SPI control of the data at the
0x1
output of the datapath.
0 Disable or zero the data from the
datapath into the DAC.
1 Use the data from the datapath
to drive the DAC.
SPI control of the data at the
input of the datapath.
R/W
0x1
R/W
0x0
R
0 Disable or zero the data feeding
into the datapath.
1 Use the data from the JESD204B
lanes to drive into the datapath.
[5:4] RESERVED
Reserved.
3
Allows TX_ENABLE to control the 0x0
DDS NCO reset.
TXEN_NCO_RESET
R/W
0 Use the SPI (HOPF_MODE bits to
control the DDS NCO reset.
1 Use the TX_ENABLE pin to
control the DDS NCO reset.
2
TXEN_DATAPATH_POST
Allows TX_ENABLE to control the 0x0
data at the output of the
datapath.
R/W
0 Use the SPI (Bit SPI_DATAPATH_
POST) for control.
1 Use the TX_ENABLE pin for
control.
1
TXEN_DATAPATH_PRE
0
TXEN_DAC_FSC
Allows TX_ENABLE to control the 0x0
data at the input of the datapath.
0 Use the SPI (Bit SPI_DATAPATH_
PRE) for control.
1 Use the TX_ENABLE pin for
control.
R/W
Allows TX_ENABLE to control the 0x0
DAC full-scale current.
R/W
0 Use the SPI register ANA_FSC0
and ANA_FSC1 for control.
1 Use the TX_ENABLE pin for
control.
0x040 ANA_DAC_BIAS_PD
0x041 ANA_FSC0
0x042 ANA_FSC1
[7:2] RESERVED
Reserved.
0x0
R
1
ANA_DAC_BIAS_PD1
Powers down the DAC core bias
circuits. A 1 powers down the
DAC core bias circuits.
0x1
R/W
0
ANA_DAC_BIAS_PD0
Powers down the DAC core bias
circuits. A 1 powers down the
DAC core bias circuits.
0x1
R/W
[7:2] RESERVED
Reserved.
0x0
R
[1:0] ANA_FULL_SCALE_CURRENT[1:0]
DAC full-scale current. Analog
full-scale current adjustment.
0x3
R/W
[7:0] ANA_FULL_SCALE_CURRENT[9:2]
DAC full-scale current. Analog
full-scale current adjustment.
0xFF
R/W
Rev. A | Page 85 of 136
AD9164
Data Sheet
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x07F CLK_PHASE_TUNE
[7:6] RESERVED
Reserved.
0x0
R
[5:0] CLK_PHASE_TUNE
Fine tuning of the clock input
phase balance. Adds small
capacitors to the CLK+/CLK−
inputs, ~ 20 fF per step, signed
magnitude.
0x0
R/W
0x0
R
0x1
R/W
Settings
Capacitance
0x080 CLK_PD
[7:1] RESERVED
Bits[5:0]
At CLK+
At CLK−
000000
0
0
000001
000010
…
1
2
…
0
0
…
011111
100000
31
0
0
0
100001
100010
111111
0
0
0
1
2
31
Reserved.
0
DACCLK_PD
DAC clock power-down. Powers
down the DAC clock circuitry.
0 Power up.
7
CLK_DUTY_EN
Enable duty cycle control.
0x1
R/W
6
CLK_DUTY_OFFSET_EN
Enable duty cycle offset.
0x0
R/W
5
CLK_DUTY_BOOST_EN
Enable duty cycle range boost.
Extends range to ±5% at cost of
1 dB to 2 dB worse phase noise.
0x0
R/W
[4:0] CLK_DUTY_PRG
Program the duty cycle offset.
5-bit signed magnitude field,
with the MSB as the sign bit and
the four LSBs as the magnitude
from 0 to 15. A larger magnitude
skews duty cycle to a greater
amount. Range is ±3%.
0x0
R/W
7
Enable clock cross control
adjustment.
0x1
R/W
[6:4] RESERVED
Reserved.
0x0
R
[3:0] CLK_CRS_ADJ
Program the clock crossing
point.
0x0
R/W
[7:6] RESERVED
Reserved.
0x0
R
[5:4] PLL_REF_CLK_RATE
PLL reference clock rate
multiplier.
0x0
R/W
0x0
R
1 Power down.
0x082 CLK_DUTY
0x083 CLK_CRS_CTRL
0x084 PLL_REF_CLK_PD
CLK_CRS_EN
00 Normal rate (1×) PLL reference
clock.
01 Double rate (2×) PLL reference
clock.
10 Quadruple rate (4×) PLL
reference clock.
11 Disable the PLL reference clock.
[3:1] RESERVED
Reserved.
0
PLL reference clock power-down. 0x0
PLL_REF_CLK_PD
0 Enable the PLL reference clock.
1 Power down the PLL reference
clock.
Rev. A | Page 86 of 136
R/W
Data Sheet
AD9164
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x088 SYSREF_CTRL0
[7:4] RESERVED
Reserved.
0x0
R
3
HYS_ON
SYSREF± hysteresis enable. This
bit enables the programmable
hysteresis control for the
SYSREF± receiver.
0x0
R/W
2
SYSREF_RISE
Use SYSREF± rising edge.
Settings
0x0
R/W
[1:0] HYS_CNTRL[9:8]
Controls the amount of
0x0
hysteresis in the SYSREF±
receiver. Each of the 10 bits adds
10 mV of differential hysteresis to
the receiver input.
R/W
0x089 SYSREF_CTRL1
[7:0] HYS_CNTRL[7:0]
Controls the amount of
0x0
hysteresis in the SYSREF±
receiver. Each of the 10 bits adds
10 mV of differential hysteresis to
the receiver input.
R/W
0x090 DLL_PD
[7:5] RESERVED
Reserved.
0x0
R
4
DLL_FINE_DC_EN
Fine delay line duty cycle
correction enable.
0x1
R/W
3
DLL_FINE_XC_EN
Fine delay line cross control
enable.
0x1
R/W
2
DLL_COARSE_DC_EN
Coarse delay line duty cycle
correction enable.
0x1
R/W
1
DLL_COARSE_XC_EN
Coarse delay line cross control
enable.
0x1
R/W
0
DLL_CLK_PD
0x1
R/W
7
DLL_TRACK_ERR
0x1
R/W
0x1
R/W
0x1
R/W
0x2
R/W
0x0
R/W
0x0
R/W
Powers down DLL and digital
clock generator.
0 Power up DLL controller.
1 Power down DLL controller.
0x091 DLL_CTRL
Track error behavior.
0 Continue on error.
1 Restart on error.
6
DLL_SEARCH_ERR
Search error behavior.
0 Stop on error.
1 Retry on error.
5
DLL_SLOPE
Desired slope.
0 Negative slope.
1 Positive slope.
[4:3] DLL_SEARCH
Search direction.
00 Search down from initial point
only.
01 Search up from initial point only.
10 Search up and down from initial
point.
[2:1] DLL_MODE
Controller mode.
00 Search then track.
01 Track only.
10 Search only.
0
DLL_ENABLE
Controller enable.
0 Disable DLL controller: use static
SPI settings.
1 Enable DLL controller: use
controller with feedback loop.
0x092 DLL_STATUS
[7:3] RESERVED
Reserved.
0x0
R
2
DLL_FAIL
The DAC clock DLL failed to lock.
0x0
R
1
DLL_LOST
The DAC clock DLL has lost lock.
0x0
R/W
0
DLL_LOCKED
The DAC clock DLL has achieved
lock.
0x0
R
Rev. A | Page 87 of 136
AD9164
Data Sheet
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x093 DLL_GB
[7:4] RESERVED
Reserved.
0x0
R
[3:0] DLL_GUARD
Search guard band.
0x0
R/W
[7:6] RESERVED
Reserved.
0x0
R
[5:0] DLL_COARSE
Coarse delay line setpoint.
0x0
R/W
0x095 DLL_FINE
[7:0] DLL_FINE
Fine delay line setpoint.
0x80
R/W
0x096 DLL_PHASE
[7:5] RESERVED
Reserved.
0x0
R
[4:0] DLL_PHS
Desired phase.
0x8
R/W
0x094 DLL_COARSE
Settings
0 Minimum allowed phase.
16 Maximum allowed phase.
0x097 DLL_BW
[7:5] RESERVED
Reserved.
0x0
R
[4:2] DLL_FILT_BW
Phase measurement filter
bandwidth.
0x0
R/W
[1:0] DLL_WEIGHT
Tracking speed.
0x0
R/W
[7:1] RESERVED
Reserved.
0x0
R
0
Read request: 0 to 1 transition
updates the coarse, fine, and
phase readback values.
0x0
R/W
[7:6] RESERVED
Reserved.
0x0
R
[5:0] DLL_COARSE_RB
Coarse delay line readback.
0x0
R
0x09A DLL_FINE_RB
[7:0] DLL_FINE_RB
Fine delay line readback.
0x0
R
0x09B DLL_PHASE_RB
[7:5] RESERVED
Reserved.
0x0
R
[4:0] DLL_PHS_RB
Phase readback.
0x0
R
[7:3] RESERVED
Reserved.
0x0
R
2
Invert digital clock from DLL.
0x0
R/W
0x098 DLL_READ
0x099 DLL_COARSE_RB
0x09D DIG_CLK_INVERT
DLL_READ
INV_DIG_CLK
0 Normal polarity.
1 Inverted polarity.
0x0A0 DLL_CLK_DEBUG
0x110 INTERP_MODE
1
DIG_CLK_DC_EN
Digital clock duty cycle
correction enable.
0x1
R/W
0
DIG_CLK_XC_EN
Digital clock cross control
enable.
0x1
R/W
7
DLL_TEST_EN
DLL clock output test enable.
0x0
R/W
[6:2] RESERVED
Reserved.
0x0
R
[1:0] DLL_TEST_DIV
DLL clock output divide.
0x0
R/W
[7:4] JESD_LANES
Number of JESD204B lanes. For
0x8
proper operation of the
JESD204B data link, this signal
must only be programmed while
the QBD is held in soft reset
(Register 0x475, Bit 3), and must
not be changed during normal
operation.
R/W
[3:0] INTERP_MODE
Interpolation mode. For proper
0x1
operation of the JESD204B data
link, this signal must only be
programmed while the QBD is
held in soft reset (Register 0x475,
Bit 3), and must not be changed
during normal operation.
R/W
0000 1× (bypass).
0001 2×.
0010 3×.
0011 4×.
0100 6×.
0101 8×.
0110 12×.
0111 16×.
1000 24×.
Rev. A | Page 88 of 136
Data Sheet
AD9164
Hex.
Addr. Name
Bits Bit Name
0x111 DATAPATH_CFG
7
INVSINC_EN
Inverse sinc filter enable.
0 Disable inverse sinc filter.
1 Enable inverse sinc filter.
0x0
R/W
6
NCO_EN
Modulation enable.
0 Disable NCO.
0x0
R/W
5
RESERVED
0x0
R
4
FILT_BW
0x0
R/W
3
RESERVED
Reserved.
0x0
R
2
MODULUS_EN
Modulus DDS enable.
0x0
R/W
0x0
R/W
Settings
Description
Reset Access
1 Enable NCO.
Reserved.
Datapath filter bandwidth.
0 Filter bandwidth is 80%.
1 Filter bandwidth is 90%.
0 Disable modulus DDS.
1 Enable modulus DDS.
1
SEL_SIDEBAND
Selects upper or lower sideband
from modulation result.
0 Use upper sideband.
1 Use lower sideband = spectral
flip.
0x113 FTW_UPDATE
0
FIR85_FILT_EN
FIR85 filter enable.
0x0
R/W
7
RESERVED
Reserved.
0x0
R
Frequency tuning word
automatic update mode.
0x0
R/W
[6:4] FTW_REQ_MODE
000 No automatic requests are
generated when the FTW
registers are written.
001 Automatically generate
FTW_LOAD_REQ after FTW0 is
written.
010 Automatically generate
FTW_LOAD_REQ after FTW1 is
written.
011 Automatically generate
FTW_LOAD_REQ after FTW2 is
written.
100 Automatically generate
FTW_LOAD_REQ after FTW3 is
written.
101 Automatically generate
FTW_LOAD_REQ after FTW4 is
written.
110 Automatically generate
FTW_LOAD_REQ after FTW5 is
written.
3
RESERVED
Reserved.
0x0
R
2
FTW_LOAD_SYSREF
FTW load and reset from rising
edge of SYSREF±.
0x0
R/W
1
FTW_LOAD_ACK
0x0
R
0
FTW_LOAD_REQ
0x0
R/W
NCO frequency tuning word. This 0x0
is X in the equation fOUT = fDAC ×
(M/N) = fDAC × ((X + A/B)/248).
R/W
Frequency tuning word update
acknowledge.
0 FTW is not loaded.
1 FTW is loaded.
0x114 FTW0
[7:0] FTW[7:0]
Rev. A | Page 89 of 136
Frequency tuning word update
request from SPI.
0 Clear FTW_LOAD_ACK.
1 0 to 1 transition loads the FTW.
AD9164
Data Sheet
Hex.
Addr. Name
Bits Bit Name
0x115 FTW1
[7:0] FTW[15:8]
NCO frequency tuning word. This 0x0
is X in the equation fOUT = fDAC ×
(M/N) = fDAC × ((X + A/B)/248).
R/W
0x116 FTW2
[7:0] FTW[23:16]
NCO frequency tuning word. This 0x0
is X in the equation fOUT = fDAC ×
(M/N) = fDAC × ((X + A/B)/248).
R/W
0x117 FTW3
[7:0] FTW[31:24]
NCO frequency tuning word. This 0x0
is X in the equation fOUT = fDAC ×
(M/N) = fDAC × ((X + A/B)/248).
R/W
0x118 FTW4
[7:0] FTW[39:32]
NCO frequency tuning word. This 0x0
is X in the equation fOUT = fDAC ×
(M/N) = fDAC × ((X + A/B)/248).
R/W
0x119 FTW5
[7:0] FTW[47:40]
NCO frequency tuning word. This 0x0
is X in the equation fOUT = fDAC ×
(M/N) = fDAC × ((X + A/B)/248).
R/W
0x11C PHASE_OFFSET0
[7:0] NCO_PHASE_OFFSET[7:0]
NCO phase offset.
0x0
R/W
0x11D PHASE_OFFSET1
[7:0] NCO_PHASE_OFFSET[15:8]
NCO phase offset.
0x0
R/W
0x124 ACC_MODULUS0
[7:0] ACC_MODULUS[7:0]
DDS Modulus. This is B in the
0x0
equation fOUT = fDAC × (M/N) = fDAC ×
((X + A/B)/248). Note this modulus
value is used for all NCO FTWs.
R/W
0x125 ACC_MODULUS1
[7:0] ACC_MODULUS[15:8]
DDS Modulus. This is B in the
0x0
equation fOUT = fDAC × (M/N) = fDAC ×
((X + A/B)/248). Note this modulus
value is used for all NCO FTWs.
R/W
0x126 ACC_MODULUS2
[7:0] ACC_MODULUS[23:16]
DDS Modulus. This is B in the
equation fOUT = fDAC × (M/N) =
fDAC × ((X + A/B)/248).Note this
modulus value is used for all
NCO FTWs.
0x0
R/W
0x127 ACC_MODULUS3
[7:0] ACC_MODULUS[31:24]
DDS Modulus. This is B in the
equation fOUT = fDAC × (M/N) =
fDAC × ((X + A/B)/248). Note this
modulus value is used for all
NCO FTWs.
0x0
R/W
0x128 ACC_MODULUS4
[7:0] ACC_MODULUS[39:32]
DDS Modulus. This is B in the
equation fOUT = fDAC × (M/N) =
fDAC × ((X + A/B)/248). Note this
modulus value is used for all
NCO FTWs.
0x0
R/W
0x129 ACC_MODULUS5
[7:0] ACC_MODULUS[47:40]
DDS Modulus. This is B in the
equation fOUT = fDAC × (M/N) =
fDAC × ((X + A/B)/248). Note this
modulus value is used for all
NCO FTWs.
0x0
R/W
0x12A ACC_DELTA0
[7:0] ACC_DELTA[7:0]
DDS Delta. This is A in the
equation fOUT = fDAC × (M/N) =
fDAC × ((X + A/B)/248). Note this
modulus value is used for all
NCO FTWs. Note this delta value
is used for all NCO FTWs.
0x0
R/W
0x12B ACC_DELTA1
[7:0] ACC_DELTA[15:8]
DDS Delta. This is A in the
equation fOUT = fDAC × (M/N) =
fDAC × ((X + A/B)/248). Note this
modulus value is used for all
NCO FTWs. Note this delta value
is used for all NCO FTWs.
0x0
R/W
0x12C ACC_DELTA2
[7:0] ACC_DELTA[23:16]
DDS Delta. This is A in the
equation fOUT = fDAC × (M/N) =
fDAC × ((X + A/B)/248). Note this
modulus value is used for all
NCO FTWs. Note this delta value
is used for all NCO FTWs.
0x0
R/W
Settings
Rev. A | Page 90 of 136
Description
Reset Access
Data Sheet
AD9164
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x12D ACC_DELTA3
[7:0] ACC_DELTA[31:24]
DDS Delta. This is A in the
equation fOUT = fDAC × (M/N) =
fDAC × ((X + A/B)/248). Note this
delta value is used for all NCO
FTWs.
0x0
R/W
0x12E ACC_DELTA4
[7:0] ACC_DELTA[39:32]
DDS Delta. This is A in the
equation fOUT = fDAC × (M/N) =
fDAC × ((X + A/B)/248). Note this
modulus value is used for all
NCO FTWs. Note this delta value
is used for all NCO FTWs.
0x0
R/W
0x12F ACC_DELTA5
[7:0] ACC_DELTA[47:40]
DDS Delta. This is A in the
equation fOUT = fDAC × (M/N) =
fDAC × ((X + A/B)/248). Note this
modulus value is used for all
NCO FTWs. Note this delta value
is used for all NCO FTWs.
0x0
R/W
0x132 TEMP_SENS_LSB
[7:0] TEMP_SENS_OUT[7:0]
Output of the temperature
sensor ADC.
0x0
R
0x133 TEMP_SENS_MSB
[7:0] TEMP_SENS_OUT[15:8]
Output of the temperature
sensor ADC.
0x0
R
0x134 TEMP_SENS_UPDATE
[7:1] RESERVED
Reserved.
0x0
R
0
TEMP_SENS_UPDATE
Set to 1 to update the
0x0
temperature sensor reading with
a new value.
R/W
7
TEMP_SENS_FAST
A 1 sets the temperature sensor
digital filter bandwidth wider for
faster settling time.
0x0
R/W
[6:1] RESERVED
Reserved.
0x10
R/W
0
TEMP_SENS_ENABLE
Set to 1 to enable the
temperature sensor.
0x0
R/W
7
PRBS_GOOD_Q
Good data indicator imaginary
channel.
0x0
R
Good data indicator real channel. 0x0
0 Incorrect sequence detected.
1 Correct PRBS sequence detected.
R
0x135 TEMP_SENS_CTRL
0x14B PRBS
Settings
0 Incorrect sequence detected.
1 Correct PRBS sequence detected.
6
PRBS_GOOD_I
5
RESERVED
4
PRBS_INV_Q
3
PRBS_INV_I
Reserved.
Data inversion imaginary
channel.
0 Expect normal data.
0x0
R
0x1
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
1 Expect inverted data.
Data inversion real channel.
0 Expect normal data.
1 Expect inverted data.
2
PRBS_MODE
Polynomial select.
0 7-bit: x7 + x6 + 1.
1 15-bit: x15 + x14 + 1.
1
PRBS_RESET
0
PRBS_EN
Reset error counters.
0 Normal operation.
1 Reset counters.
Enable PRBS checker.
0 Disable.
1 Enable.
0x14C PRBS_ERROR_I
[7:0] PRBS_COUNT_I
Error count value real channel.
0x0
R
0x14D PRBS_ERROR_Q
[7:0] PRBS_COUNT_Q
Error count value imaginary
channel.
0x0
R
0x14E TEST_DC_DATA1
[7:0] DC_TEST_DATA[15:8]
DC test data.
0x0
R/W
Rev. A | Page 91 of 136
AD9164
Data Sheet
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x14F TEST_DC_DATA0
[7:0] DC_TEST_DATA[7:0]
DC test data.
0x0
R/W
0x150 DIG_TEST
[7:2] RESERVED
Reserved.
0x0
R
1
DC data test mode enable.
0x0
R/W
Settings
DC_TEST_EN
1 DC test mode enable.
0 DC test mode disable.
0
0x151 DECODE_CTRL
RESERVED
Reserved.
0x0
R/W
[7:3] RESERVED
Reserved.
0x0
R/W
0x0
R/W
2
SHUFFLE
Shuffle mode. Enables shuffle
mode for better spurious
performance.
0 Disable MSB shuffling (use
thermometer encoding).
1 Enable MSB shuffling.
0x152 DECODE_MODE
[1:0] RESERVED
Reserved.
0x0
R/W
[7:2] RESERVED
Reserved.
0x0
R
[1:0] DECODE_MODE
Decode mode.
0x0
R/W
00 Nonreturn-to-zero mode (first
Nyquist).
01 Mix-Mode (second Nyquist).
10 Return to zero.
11 Reserved.
0x1DF SPI_STRENGTH
0x200 MASTER_PD
0x201 PHY_PD
[7:4] RESERVED
Reserved.
0x0
R
[3:0] SPIDRV
Slew and drive strength for
CMOS SPI outputs. Slew =
Bits[1:0], drive = Bits[3:2].
0xF
R/W
[7:1] RESERVED
Reserved.
0x0
R
0
Powers down the entire
JESD204B Rx analog (all eight
channels and bias).
0x1
R/W
SPI override to power down the 0x0
individual PHYs.
Bit 0 controls the SERDIN0± PHY.
Bit 1 controls the SERDIN1± PHY.
R/W
SPI_PD_MASTER
[7:0] SPI_PD_PHY
Bit 2 controls the SERDIN2± PHY.
Bit 3 controls the SERDIN3± PHY.
Bit 4 controls the SERDIN4± PHY.
Bit 5 controls the SERDIN5± PHY.
Bit 6 controls the SERDIN6± PHY.
Bit 7 controls the SERDIN7± PHY.
0x203 GENERIC_PD
0x206 CDR_RESET
[7:2] RESERVED
Reserved.
0x0
R
1
SPI_SYNC1_PD
Powers down LVDS buffer for the 0x0
sync request signal, SYNCOUT.
R/W
0
RESERVED
Reserved.
0x0
R/W
[7:1] RESERVED
Reserved.
0x0
R
0
Resets the digital control logic
for all PHYs.
0x1
R/W
0x0
R/W
Enables half rate CDR operation, 0x1
must be enabled for data rates
above 6 Gbps.
0 Disables CDR half rate operation,
data rate ≤ 6 Gbps.
R/W
SPI_CDR_RESET
0 CDR logic is reset.
1 CDR logic is operational.
0x230 CDR_OPERATING_MODE_REG_0
[7:6] RESERVED
5
Reserved.
SPI_ENHALFRATE
1 Enables CDR half rate operation,
data rate > 6 Gbps.
Rev. A | Page 92 of 136
Data Sheet
Hex.
Addr. Name
AD9164
Bits Bit Name
Settings
[4:3] RESERVED
[2:1] SPI_DIVISION_RATE
0
0x250 EQ_CONFIG_PHY_0_1
RESERVED
Description
Reset Access
Reserved.
0x1
R/W
0x0
R/W
0x0
R/W
0x8
R/W
0x8
R/W
0x8
R/W
Enables oversampling of the
input data.
00 No division. Data rate > 3 Gbps.
01 Division by 2. 1.5 Gbps < data
rate ≤ 3 Gbps.
10 Division by 4. 750 Mbps < data
rate ≤ 1.5 Gbps.
Reserved.
[7:4] SPI_EQ_CONFIG1
0000 Manual mode (SPI configured
values used).
0001 Boost level = 1.
0010 Boost level = 2.
0011 Boost level = 3.
0100 Boost level = 4.
0101 Boost level = 5.
0110 Boost level = 6.
0111 Boost level = 7.
1000 Boost level = 8.
1001 Boost level = 9.
1010 Boost level = 10.
1011 Boost level = 11.
1100 Boost level = 12.
1101 Boost level = 13.
1110 Boost level = 14.
1111 Boost level = 15.
[3:0] SPI_EQ_CONFIG0
0000 Manual mode (SPI configured
values used).
0001 Boost level = 1.
0010 Boost level = 2.
0011 Boost level = 3.
0100 Boost level = 4.
0101 Boost level = 5.
0110 Boost level = 6.
0111 Boost level = 7.
1000 Boost level = 8.
1001 Boost level = 9.
1010 Boost level = 10.
1011 Boost level = 11.
1100 Boost level = 12.
1101 Boost level = 13.
1110 Boost level = 14.
1111 Boost level = 15.
0x251 EQ_CONFIG_PHY_2_3
[7:4] SPI_EQ_CONFIG3
0000 Manual mode (SPI configured
values used).
0001 Boost level = 1.
0010 Boost level = 2.
0011 Boost level = 3.
0100 Boost level = 4.
0101 Boost level = 5.
0110 Boost level = 6.
Rev. A | Page 93 of 136
AD9164
Hex.
Addr. Name
Data Sheet
Bits Bit Name
Settings
Description
Reset Access
0111 Boost level = 7.
1000 Boost level = 8.
1001 Boost level = 9.
1010 Boost level = 10.
1011 Boost level = 11.
1100 Boost level = 12.
1101 Boost level = 13.
1110 Boost level = 14.
1111 Boost level = 15.
[3:0] SPI_EQ_CONFIG2
0x8
R/W
0x8
R/W
0x8
R/W
0000 Manual mode (SPI configured
values used).
0001 Boost level = 1.
0010 Boost level = 2.
0011 Boost level = 3.
0100 Boost level = 4.
0101 Boost level = 5.
0110 Boost level = 6.
0111 Boost level = 7.
1000 Boost level = 8.
1001 Boost level = 9.
1010 Boost level = 10.
1011 Boost level = 11.
1100 Boost level = 12.
1101 Boost Level = 13.
1110 Boost level = 14.
1111 Boost level = 15.
0x252 EQ_CONFIG_PHY_4_5
[7:4] SPI_EQ_CONFIG5
0000 Manual mode (SPI configured
values used).
0001 Boost level = 1.
0010 Boost level = 2.
0011 Boost level = 3.
0100 Boost level = 4.
0101 Boost level = 5.
0110 Boost level = 6.
0111 Boost level = 7.
1000 Boost level = 8.
1001 Boost level = 9.
1010 Boost level = 10.
1011 Boost level = 11.
1100 Boost level = 12.
1101 Boost level = 13.
1110 Boost level = 14.
1111 Boost level = 15.
[3:0] SPI_EQ_CONFIG4
0000 Manual mode (SPI configured
values used).
0001 Boost level = 1.
0010 Boost level = 2.
0011 Boost level = 3.
0100 Boost level = 4.
0101 Boost level = 5.
0110 Boost level = 6.
Rev. A | Page 94 of 136
Data Sheet
Hex.
Addr. Name
AD9164
Bits Bit Name
Settings
Description
Reset Access
0111 Boost level = 7.
1000 Boost level = 8.
1001 Boost level = 9.
1010 Boost level = 10.
1011 Boost level = 11.
1100 Boost level = 12.
1101 Boost level = 13.
1110 Boost level = 14.
1111 Boost level = 15.
0x253 EQ_CONFIG_PHY_6_7
[7:4] SPI_EQ_CONFIG7
0x8
R/W
0x8
R/W
0x1
R/W
0x4
R/W
0000 Manual mode (SPI configured
values used).
0001 Boost level = 1.
0010 Boost level = 2.
0011 Boost level = 3.
0100 Boost level = 4.
0101 Boost level = 5.
0110 Boost level = 6.
0111 Boost level = 7.
1000 Boost level = 8.
1001 Boost level = 9.
1010 Boost level = 10.
1011 Boost level = 11.
1100 Boost level = 12.
1101 Boost level = 13.
1110 Boost level = 14.
1111 Boost level = 15.
[3:0] SPI_EQ_CONFIG6
0000 Manual mode (SPI configured
values used).
0001 Boost level = 1.
0010 Boost level = 2.
0011 Boost level = 3.
0100 Boost level = 4.
0101 Boost level = 5.
0110 Boost level = 6.
0111 Boost level = 7.
1000 Boost level = 8.
1001 Boost level = 9.
1010 Boost level = 10.
1011 Boost level = 11.
1100 Boost level = 12.
1101 Boost level = 13.
1110 Boost level = 14.
1111 Boost level = 15.
0x268 EQ_BIAS_REG
[7:6] EQ_POWER_MODE
Controls the equalizer power
mode/insertion loss capability.
00 Normal mode.
01 Low power mode.
[5:0] RESERVED
Reserved.
Rev. A | Page 95 of 136
AD9164
Data Sheet
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x280 SYNTH_ENABLE_CNTRL
[7:3] RESERVED
Reserved.
0x0
R
2
SPI_RECAL_SYNTH
Set this bit high to rerun all of the
SERDES PLL calibration routines.
Set this bit low again to allow
additional recalibrations. Rising
edge causes the calibration.
0x0
R/W
1
RESERVED
Reserved.
0x0
R/W
0
SPI_ENABLE_SYNTH
Enable the SERDES PLL. Setting
this bit turns on all currents and
proceeds to calibrate the PLL.
Make sure reference clock and
division ratios are correct before
enabling this bit.
0x0
R/W
Reserved.
0x0
R
0x281 PLL_STATUS
Settings
[7:6] RESERVED
5
SPI_CP_OVER_RANGE_HIGH_RB
If set, the SERDES PLL CP output
is above valid operating range.
0 Charge pump output is within
operating range.
1 Charge pump output is above
operating range.
0x0
R
4
SPI_CP_OVER_RANGE_LOW_RB
If set, the SERDES PLL CP output
is below valid operating range.
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0 Charge pump output is within
operating range.
1 Charge pump output is below
operating range.
3
SPI_CP_CAL_VALID_RB
This bit tells the user if the
charge pump calibration has
completed and is valid.
0 Charge pump calibration is not
valid.
1 Charge pump calibration is valid.
[2:1] RESERVED
0
Reserved.
SPI_PLL_LOCK_RB
If set, the SERDES synthesizer
locked.
0 PLL is not locked.
1 PLL is locked.
0x289 REF_CLK_DIVIDER_LDO
[7:2] RESERVED
Reserved.
[1:0] SERDES_PLL_DIV_FACTOR
0x2A7 TERM_BLK1_CTRLREG0
SERDES PLL reference clock
0x0
division factor. This field controls
the division of the SERDES PLL
reference clock before it is fed
into the SERDES PLL PFD. It must
be set so that fREF/DivFactor is
between 35 MHz and 80 MHz.
00 Divide by 4 for lane rate between
6 Gbps and 12.5 Gbps.
01 Divide by 2 for lane rate between
3 Gbps and 6 Gbps.
10 Divide by 1 for lane rate between
1.5 Gbps and 3 Gbps.
R/W
[7:1] RESERVED
Reserved.
0x0
R
0
Rising edge of this bit starts a
termination calibration routine.
0x0
R/W
SPI_I_TUNE_R_CAL_TERMBLK1
Rev. A | Page 96 of 136
Data Sheet
AD9164
Hex.
Addr. Name
Bits Bit Name
Settings
0x2A8 TERM_BLK1_CTRLREG1
[7:0] SPI_I_SERIALIZER_RTRIM_TERMBLK1
SPI override for termination
value for PHY 0, PHY 1, PHY 6,
and PHY 7. Value options are as
follows:
XXX0XXXX Automatically calibrate
termination value.
XXX1000X Force 000 as termination value.
XXX1001X Force 001 as termination value.
Description
Reset Access
0x0
R/W
XXX1010X Force 010 as termination value.
XXX1011X Force 011 as termination value.
XXX1100X Force 100 as termination value.
XXX1101X Force 101 as termination value.
XXX1110X Force 110 as termination value.
XXX1111X Force 111 as termination value.
XXX1000X Force 000 as termination value.
0x2AC TERM_BLK1_RD_REG0
0x2AE TERM_BLK2_CTRLREG0
0x2AF TERM_BLK2_CTRLREG1
[7:4] RESERVED
Reserved.
0x0
R
[3:0] SPI_O_RCAL_CODE_TERMBLK1
Readback of calibration code for
PHY 0, PHY 1, PHY 6, and PHY 7.
0x0
R
[7:1] RESERVED
Reserved.
0x0
R
0
Rising edge of this bit starts a
termination calibration routine.
0x0
R/W
SPI override for termination
value for PHY 2, PHY 3, PHY 4,
and PHY 5. Value options are as
follows:
XXX0XXXX Automatically calibrate
termination value.
XXX1000X Force 000 as termination value.
XXX1001X Force 001 as termination value.
0x0
R/W
SPI_I_TUNE_R_CAL_TERMBLK2
[7:0] SPI_I_SERIALIZER_RTRIM_TERMBLK2
XXX1010X Force 010 as termination value.
XXX1011X Force 011 as termination value.
XXX1100X Force 100 as termination value.
XXX1101X Force 101 as termination value.
XXX1110X Force 110 as termination value.
XXX1111X Force 111 as termination value.
XXX1000X Force 000 as termination value.
0x2B3 TERM_BLK2_RD_REG0
0x2BB TERM_OFFSET_0
0x2BC TERM_OFFSET_1
[7:4] RESERVED
Reserved.
0x0
R
[3:0] SPI_O_RCAL_CODE_TERMBLK2
Readback of calibration code for
PHY 2, PHY 3, PHY 4, and PHY 5.
0x0
R
[7:4] RESERVED
Reserved.
0x0
R
[3:0] TERM_OFFSET_0
Add or subtract from the
termination calibration value of
Physical Lane 0. 4-bit signed
magnitude value that adds to or
subtracts from the termination
value. Bit 3 is the sign bit, and
Bits[2:0] are the magnitude bits.
0x0
R/W
[7:4] RESERVED
Reserved.
0x0
R
[3:0] TERM_OFFSET_1
Add or subtract from the
termination calibration value of
Physical Lane 1. 4-bit signed
magnitude value that adds to or
subtracts from the termination
value. Bit 3 is the sign bit, and
Bits[2:0] are the magnitude bits.
0x0
R/W
Rev. A | Page 97 of 136
AD9164
Data Sheet
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x2BD TERM_OFFSET_2
[7:4] RESERVED
Reserved.
0x0
R
[3:0] TERM_OFFSET_2
Add or subtract from the
termination calibration value of
Physical Lane 2. 4-bit signed
magnitude value that adds to or
subtracts from the termination
value. Bit 3 is the sign bit, and
Bits[2:0] are the magnitude bits.
0x0
R/W
[7:4] RESERVED
Reserved.
0x0
R
[3:0] TERM_OFFSET_3
Add or subtract from the
termination calibration value of
Physical Lane 3. 4-bit signed
magnitude value that adds to or
subtracts from the termination
value. Bit 3 is the sign bit, and
Bits[2:0] are the magnitude bits.
0x0
R/W
[7:4] RESERVED
Reserved.
0x0
R
[3:0] TERM_OFFSET_4
Add or subtract from the
termination calibration value of
Physical Lane 4. 4-bit signed
magnitude value that adds to or
subtracts from the termination
value. Bit 3 is the sign bit, and
Bits[2:0] are the magnitude bits.
0x0
R/W
[7:4] RESERVED
Reserved.
0x0
R
[3:0] TERM_OFFSET_5
Add or subtract from the
termination calibration value of
Physical Lane 5. 4-bit signed
magnitude value that adds to or
subtracts from the termination
value. Bit 3 is the sign bit, and
Bits[2:0] are the magnitude bits.
0x0
R/W
[7:4] RESERVED
Reserved.
0x0
R
[3:0] TERM_OFFSET_6
Add or subtract from the
termination calibration value of
Physical Lane 6. 4-bit signed
magnitude value that adds to or
subtracts from the termination
value. Bit 3 is the sign bit, and
Bits[2:0] are the magnitude bits.
0x0
R/W
[7:4] RESERVED
Reserved.
0x0
R
[3:0] TERM_OFFSET_7
Add or subtract from the
termination calibration value of
Physical Lane 7. 4-bit signed
magnitude value that adds to or
subtracts from the termination
value. Bit 3 is the sign bit, and
Bits[2:0] are the magnitude bits.
0x0
R/W
7
RESERVED
Reserved.
0x0
R
6
CHECKSUM_MODE
0x0
R/W
0x0
R
0x2BE TERM_OFFSET_3
0x2BF TERM_OFFSET_4
0x2C0 TERM_OFFSET_5
0x2C1 TERM_OFFSET_6
0x2C2 TERM_OFFSET_7
0x300 GENERAL_JRX_CTRL_0
Settings
JESD204B link parameter
checksum calculation method.
0 Checksum is sum of fields.
1 Checksum is sum of octets.
0x302 DYN_LINK_LATENCY_0
[5:1] RESERVED
Reserved.
0
This bit brings up the JESD204B 0x0
receiver when all link parameters
are programmed and all clocks
are ready.
R/W
[7:5] RESERVED
Reserved.
0x0
R
[4:0] DYN_LINK_LATENCY_0
Measurement of the JESD204B
link delay (in PCLK units). Link 0
dynamic link latency. Latency
between current deframer LMFC
and the global LMFC.
0x0
R
LINK_EN
Rev. A | Page 98 of 136
Data Sheet
AD9164
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x304 LMFC_DELAY_0
[7:5] RESERVED
Reserved.
0x0
R
[4:0] LMFC_DELAY_0
Fixed part of the JESD204B link
delay (in PCLK units). Delay in
frame clock cycles for global
LMFC for Link 0.
0x0
R/W
[7:5] RESERVED
Reserved.
0x0
R
[4:0] LMFC_VAR_0
Variable part of the JESD204B
link delay (in PCLK units).
Location in Rx LMFC where
JESD204B words are read out
from buffer. This setting must
not be more than 10 PCLKs.
0x1F
R/W
[7:6] RESERVED
Reserved.
0x0
R
0x1
R/W
0x0
R/W
0x306 LMFC_VAR_0
0x308 XBAR_LN_0_1
Settings
[5:3] SRC_LANE1
Select data from SERDIN0±,
SERDIN1±, …, or SERDIN7± for
Logic Lane 1.
000 Data is from SERDIN0±.
001 Data is from SERDIN1±.
010 Data is from SERDIN2±.
011 Data is from SERDIN3±.
100 Data is from SERDIN4±.
101 Data is from SERDIN5±.
110 Data is from SERDIN6±.
111 Data is from SERDIN7±.
[2:0] SRC_LANE0
Select data from SERDIN0±,
SERDIN1±, …, or SERDIN7± for
Logic Lane 0.
000 Data is from SERDIN0±.
001 Data is from SERDIN1±.
010 Data is from SERDIN2±.
011 Data is from SERDIN3±.
100 Data is from SERDIN4±.
101 Data is from SERDIN5±.
110 Data is from SERDIN6±.
111 Data is from SERDIN7±.
0x309 XBAR_LN_2_3
[7:6] RESERVED
Reserved.
0x0
R
[5:3] SRC_LANE3
Select data from SERDIN0±,
SERDIN1±, …, or SERDIN7± for
Logic Lane 3.
0x3
R/W
000 Data is from SERDIN0±.
001 Data is from SERDIN1±.
010 Data is from SERDIN2±.
011 Data is from SERDIN3±.
100 Data is from SERDIN4±.
101 Data is from SERDIN5±.
110 Data is from SERDIN6±.
111 Data is from SERDIN7±.
Rev. A | Page 99 of 136
AD9164
Hex.
Addr. Name
Data Sheet
Bits Bit Name
Settings
[2:0] SRC_LANE2
Description
Reset Access
Select data from SERDIN0±,
SERDIN1±, …, or SERDIN7± for
Logic Lane 2.
0x2
R/W
000 Data is from SERDIN0±.
001 Data is from SERDIN1±.
010 Data is from SERDIN2±.
011 Data is from SERDIN3±.
100 Data is from SERDIN4±.
101 Data is from SERDIN5±.
110 Data is from SERDIN6±.
111 Data is from SERDIN7±.
0x30A XBAR_LN_4_5
[7:6] RESERVED
Reserved.
0x0
R
[5:3] SRC_LANE5
Select data from SERDIN0±,
SERDIN1±, …, or SERDIN7± for
Logic Lane 5.
0x5
R/W
0x4
R/W
0x0
R
0x7
R/W
000 Data is from SERDIN0±.
001 Data is from SERDIN1±.
010 Data is from SERDIN2±.
011 Data is from SERDIN3±.
100 Data is from SERDIN4±.
101 Data is from SERDIN5±.
110 Data is from SERDIN6±.
111 Data is from SERDIN7±.
[2:0] SRC_LANE4
Select data from SERDIN0±,
SERDIN1±, …, or SERDIN7± for
Logic Lane 4.
000 Data is from SERDIN0±.
001 Data is from SERDIN1±.
010 Data is from SERDIN2±.
011 Data is from SERDIN3±.
100 Data is from SERDIN4±.
101 Data is from SERDIN5±.
110 Data is from SERDIN6±.
111 Data is from SERDIN7±.
0x30B XBAR_LN_6_7
[7:6] RESERVED
Reserved.
[5:3] SRC_LANE7
Select data from SERDIN0±,
SERDIN1±, …, or SERDIN7± for
Logic Lane 7.
000 Data is from SERDIN0±.
001 Data is from SERDIN1±.
010 Data is from SERDIN2±.
011 Data is from SERDIN3±.
100 Data is from SERDIN4±.
101 Data is from SERDIN5±.
110 Data is from SERDIN6±.
111 Data is from SERDIN7±.
Rev. A | Page 100 of 136
Data Sheet
Hex.
Addr. Name
AD9164
Bits Bit Name
Settings
[2:0] SRC_LANE6
Description
Reset Access
Select data from SERDIN0±,
SERDIN1±, …, or SERDIN7± for
Logic Lane 6.
0x6
R/W
000 Data is from SERDIN0±.
001 Data is from SERDIN1±.
010 Data is from SERDIN2±.
011 Data is from SERDIN3±.
100 Data is from SERDIN4±.
101 Data is from SERDIN5±.
110 Data is from SERDIN6±.
111 Data is from SERDIN7±.
0x30C FIFO_STATUS_REG_0
[7:0] LANE_FIFO_FULL
Bit 0 corresponds to FIFO full flag 0x0
for data from SERDIN0±.
R
Bit 1 corresponds to FIFO full flag
for data from SERDIN1±.
Bit 2 corresponds to FIFO full flag
for data from SERDIN2±.
Bit 3 corresponds to FIFO full flag
for data from SERDIN3±.
Bit 4 corresponds to FIFO full flag
for data from SERDIN4±.
Bit 5 corresponds to FIFO full flag
for data from SERDIN5±.
Bit 6 corresponds to FIFO full flag
for data from SERDIN6±.
Bit 7 corresponds to FIFO full flag
for data from SERDIN7±.
0x30D FIFO_STATUS_REG_1
[7:0] LANE_FIFO_EMPTY
Bit 0 corresponds to FIFO empty
flag for data from SERDIN0±.
Bit 1 corresponds to FIFO empty
flag for data from SERDIN1±.
Bit 2 corresponds to FIFO empty
flag for data from SERDIN2±.
Bit 3 corresponds to FIFO empty
flag for data from SERDIN3±.
0x0
R
Bit 4 corresponds to FIFO empty
flag for data from SERDIN4±.
Bit 5 corresponds to FIFO empty
flag for data from SERDIN5±.
Bit 6 corresponds to FIFO empty
flag for data from SERDIN6±.
Bit 7 corresponds to FIFO empty
flag for data from SERDIN7±.
0x311 SYNC_GEN_0
[7:3] RESERVED
Reserved.
0x0
R
2
Mask EOMF from QBD_0. Assert
SYNCOUT based on loss of
multiframe sync.
0x0
R/W
EOMF_MASK_0
0 Do not assert SYNCOUT on loss
of multiframe.
1 Assert SYNCOUT on loss of
multiframe.
1
RESERVED
Reserved.
0x0
R/W
0
EOF_MASK_0
Mask EOF from QBD_0. Assert
0x0
SYNCOUT based on loss of frame
sync.
R/W
0 Do not assert SYNCOUT on loss
of frame.
1 Assert SYNCOUT on loss of
frame.
Rev. A | Page 101 of 136
AD9164
Data Sheet
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x312 SYNC_GEN_1
[7:4] SYNC_ERR_DUR
Duration of SYNCOUT signal low
for purpose of sync error report.
0 means half PCLK cycle. Add an
additional PCLK = 4 octets for
each increment of the value.
0x0
R/W
[3:0] SYNC_SYNCREQ_DUR
Duration of SYNCOUT signal low 0x0
for purpose of sync request. 0
means 5 frame + 9 octets. Add an
additional PCLK = 4 octets for
each increment of the value.
R/W
0x313 SYNC_GEN_3
[7:0] LMFC_PERIOD
LMFC period in PCLK cycle. This
is to report the global LMFC
period based on PCLK.
0x0
R
0x315 PHY_PRBS_TEST_EN
[7:0] PHY_TEST_EN
0x0
R/W
0x316 PHY_PRBS_TEST_CTRL
7
0x0
R
0x0
R/W
0x0
R/W
Start and stop the PHY PRBS test. 0x0
0 Test not started.
R/W
Settings
RESERVED
Enable PHY BER by ungating the
clocks.
1 PHY test enable.
0 PHY test disable.
Reserved.
[6:4] PHY_SRC_ERR_CNT
000 Report Lane 0 error count.
001 Report Lane 1 error count.
010 Report Lane 2 error count.
011 Report Lane 3 error count.
100 Report Lane 4 error count.
101 Report Lane 5 error count.
110 Report Lane 6 error count.
111 Report Lane 7 error count.
[3:2] PHY_PRBS_PAT_SEL
Select PRBS pattern for PHY BER
test.
00 PRBS7.
01 PRBS15.
10 PRBS31.
11 Not used.
1
PHY_TEST_START
0
PHY_TEST_RESET
1 Test started.
Reset PHY PRBS test state
machine and error counters.
0x0
R/W
Bits[7:0] of the 24-bit threshold
value set the error flag for PHY
PRBS test.
0x0
R/W
0x318 PHY_PRBS_TEST_THRESHOLD_MIDBITS [7:0] PHY_PRBS_THRESHOLD_MIDBITS
Bits[15:8] of the 24-bit threshold
value set the error flag for PHY
PRBS test.
0x0
R/W
0x319 PHY_PRBS_TEST_THRESHOLD_HIBITS
[7:0] PHY_PRBS_THRESHOLD_HIBITS
Bits[23:16] of the 24-bit
threshold value set the error flag
for PHY PRBS test.
0x0
R/W
0x31A PHY_PRBS_TEST_ERRCNT_LOBITS
[7:0] PHY_PRBS_ERR_CNT_LOBITS
Bits[7:0] of the 24-bit reported
PHY BER test error count from
selected lane.
0x0
R
0x31B PHY_PRBS_TEST_ERRCNT_MIDBITS
[7:0] PHY_PRBS_ERR_CNT_MIDBITS
Bits[15:8] of the 24-bit reported
PHY BER test error count from
selected lane.
0x0
R
0x31C PHY_PRBS_TEST_ERRCNT_HIBITS
[7:0] PHY_PRBS_ERR_CNT_HIBITS
Bits[23:16] of the 24-bit reported
PHY BER test error count from
selected lane.
0x0
R
0 Not reset.
1 Reset.
0x317 PHY_PRBS_TEST_THRESHOLD_LOBITS
[7:0] PHY_PRBS_THRESHOLD_LOBITS
Rev. A | Page 102 of 136
Data Sheet
AD9164
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x31D PHY_PRBS_TEST_STATUS
[7:0] PHY_PRBS_PASS
Each bit is for the corresponding
lane. Report PHY BER test
pass/fail for each lane.
0xFF
R
0x31E PHY_DATA_SNAPSHOT_CTRL
[7:5] RESERVED
Reserved.
0x0
R
[4:2] PHY_GRAB_LANE_SEL
Select which lane to grab data.
0x0
R/W
0x0
R/W
0x0
R/W
Settings
000 Grab data from Lane 0.
001 Grab data from Lane 1.
010 Grab data from Lane 2.
011 Grab data from Lane 3.
100 Grab data from Lane 4.
101 Grab data from Lane 5.
110 Grab data from Lane 6.
111 Grab data from Lane 7.
1
PHY_GRAB_MODE
0
PHY_GRAB_DATA
Use error trigger to grab data.
0 Grab data when
PHY_GRAB_DATA is set.
1 Grab data upon bit error.
Transition from 0 to 1 causes
logic to store current receive
data from one lane.
0x31F PHY_SNAPSHOT_DATA_BYTE0
[7:0] PHY_SNAPSHOT_DATA_BYTE0
Current data received represents 0x0
PHY_SNAPSHOT_DATA[7:0].
R
0x320 PHY_SNAPSHOT_DATA_BYTE1
[7:0] PHY_SNAPSHOT_DATA_BYTE1
Current data received represents 0x0
PHY_SNAPSHOT_DATA[15:8].
R
0x321 PHY_SNAPSHOT_DATA_BYTE2
[7:0] PHY_SNAPSHOT_DATA_BYTE2
Current data received represents 0x0
PHY_SNAPSHOT_DATA[23:16].
R
0x322 PHY_SNAPSHOT_DATA_BYTE3
[7:0] PHY_SNAPSHOT_DATA_BYTE3
Current data received represents 0x0
PHY_SNAPSHOT_DATA[31:24].
R
0x323 PHY_SNAPSHOT_DATA_BYTE4
[7:0] PHY_SNAPSHOT_DATA_BYTE4
Current data received represents 0x0
PHY_SNAPSHOT_DATA[39:32].
R
0x32C SHORT_TPL_TEST_0
[7:4] SHORT_TPL_SP_SEL
Short transport layer sample
0x0
selection. Select which sample to
check from a specific DAC.
R/W
0000 Sample 0.
0001 Sample 1.
0010 Sample 2.
0011 Sample 3.
0100 Sample 4.
0101 Sample 5.
0110 Sample 6.
0111 Sample 7.
1000 Sample 8.
1001 Sample 9.
1010 Sample 10.
1011 Sample 11.
1100 Sample 12.
1101 Sample 13.
1110 Sample 14.
1111 Sample 15.
[3:2] SHORT_TPL_M_SEL
Short transport layer test DAC
selection. Select which DAC to
check.
00 DAC 0.
01 DAC 1.
10 DAC 2.
11 DAC 3.
Rev. A | Page 103 of 136
0x0
R/W
AD9164
Hex.
Addr. Name
Data Sheet
Bits Bit Name
1
Settings
SHORT_TPL_TEST_RESET
Description
Reset Access
Short transport layer test reset.
Resets the result of short
transport layer test.
0x0
R/W
Short transport layer test enable. 0x0
Enable short transport layer test.
0 Disable.
R/W
0 Not reset.
1 Reset.
0
SHORT_TPL_TEST_EN
1 Enable.
0x32D SHORT_TPL_TEST_1
[7:0] SHORT_TPL_REF_SP_LSB
Short transport layer reference
sample LSB. This is the lower
eight bits of expected DAC
sample. It is used to compare
with the received DAC sample at
the output of JESD204B Rx.
0x0
R/W
0x32E SHORT_TPL_TEST_2
[7:0] SHORT_TPL_REF_SP_MSB
Short transport layer test
0x0
reference sample MSB. This is the
upper eight bits of expected
DAC sample. It is used to
compare with the received
sample at JESD204B Rx output.
R/W
0x32F SHORT_TPL_TEST_3
[7:1] RESERVED
Reserved.
0x0
R
0x0
R
0
SHORT_TPL_FAIL
Short transport layer test fail.
This bit shows if the selected
DAC sample matches the
reference sample. If they match,
the test passes; otherwise, the
test fails.
0 Test pass.
1 Test fail.
0x334 JESD_BIT_INVERSE_CTRL
[7:0] JESD_BIT_INVERSE
Each bit of this byte inverses the 0x0
JESD204B deserialized data from
one specific JESD204B Rx PHY.
The bit order matches the logical
lane order. For example, Bit 0
controls Lane 0, Bit 1 controls
Lane 1.
R/W
0x400 DID_REG
[7:0] DID_RD
Received ILAS configuration on
0x0
Lane 0. DID is the device ID
number. Link information
received on Lane 0 as specified in
Section 8.3 of JESD204B.
R
0x401 BID_REG
[7:0] BID_RD
Received ILAS configuration on
Lane 0. BID is the bank ID,
extension to DID. Link
information received on Lane 0
as specified in Section 8.3 of
JESD204B.
0x0
R
0x402 LID0_REG
7
RESERVED
Reserved.
0x0
R
6
ADJDIR_RD
Received ILAS configuration on
0x0
Lane 0. ADJDIR is the direction to
adjust the DAC LMFC. Link
information received on Lane 0
as specified in Section 8.3 of
JESD204B.
R
5
PHADJ_RD
Received ILAS configuration on
Lane 0. PHADJ is the phase
adjustment request to DAC. Link
information received on Lane 0
as specified in Section 8.3 of
JESD204B.
R
Rev. A | Page 104 of 136
0x0
Data Sheet
Hex.
Addr. Name
AD9164
Bits Bit Name
Settings
[4:0] LL_LID0
0x403 SCR_L_REG
7
SCR_RD
[6:5] RESERVED
Description
Reset Access
Received ILAS LID configuration
on Lane 0. LID0 is the lane
identification for Lane 0. Link
information received on Lane 0
as specified in Section 8.3 of
JESD204B.
0x0
R
Received ILAS configuration on
Lane 0. SCR is the Tx scrambling
status. Link information received
on Lane 0 as specified in
Section 8.3 of JESD204B.
0 Scrambling is disabled.
1 Scrambling is enabled.
0x0
R
0x0
R
0x0
R
0x0
R
Reserved.
[4:0] L_RD
Received ILAS configuration on
Lane 0. L is the number of lanes
per converter device. Link
information received on Lane 0
as specified in Section 8.3 of
JESD204B.
00000 1 lane per converter device.
00001 2 lanes per converter device.
00011 4 lanes per converter device.
00111 8 lanes per converter device.
0x404 F_REG
[7:0] F_RD
Received ILAS configuration on
Lane 0. F is the number of octets
per frame. Settings of 1, 2, and 4
are valid (value in register is F −
1). Link information received on
Lane 0 as specified in Section 8.3
of JESD204B.
0 1 octet per frame.
1 2 octets per frame.
11 4 octets per frame.
0x405 K_REG
[7:5] RESERVED
Reserved.
0x0
R
[4:0] K_RD
Received ILAS configuration on
0x0
Lane 0. K is the number of frames
per multiframe. Settings of 16 or
32 are valid. On this device, all
modes use K = 32 (value in
register is K − 1). Link
information received on Lane 0
as specified in Section 8.3 of
JESD204B.
R
01111 16 frames per multiframe.
11111 32 frames per multiframe.
0x406 M_REG
[7:0] M_RD
Received ILAS configuration on
Lane 0. M is the number of
converters per device. Link
information received on Lane 0
as specified in Section 8.3 of
JESD204B. M is 1 for real
interface and 2 for complex
interface (value in register is M −
1).
0x0
R
0x407 CS_N_REG
[7:6] CS_RD
Received ILAS configuration on
Lane 0. CS is the number of
control bits per sample. Link
information received on Lane 0
as specified in Section 8.3 of
JESD204B. CS is always 0 on this
device.
0x0
R
5
Reserved.
0x0
R
RESERVED
Rev. A | Page 105 of 136
AD9164
Hex.
Addr. Name
0x408 NP_REG
Data Sheet
Bits Bit Name
Settings
Description
Reset Access
[4:0] N_RD
Received ILAS configuration on
0x0
Lane 0. N is the converter resolution. Value in register is N − 1 (for
example, 16 bits = 0b01111).
R
[7:5] SUBCLASSV_RD
Received ILAS configuration on
Lane 0. SUBCLASSV is the device
subclass version. Link
information received on Lane 0
as specified in Section 8.3 of
JESD204B.
0x0
R
[4:0] NP_RD
Received ILAS configuration on
0x0
Lane 0. NP is the total number of
bits per sample. Link information
received on Lane 0 as specified in
Section 8.3 of JESD204B. Value in
register is NP − 1, for example,
16 bits per sample = 0b01111.
R
[7:5] JESDV_RD
Received ILAS configuration on
0x0
Lane 0. JESDV is the JESD204x
version. Link information
received on Lane 0 as specified in
Section 8.3 of JESD204B.
R
000 Subclass 0.
001 Subclass 1.
0x409 S_REG
000 JESD204A.
001 JESD204B.
[4:0] S_RD
0x40A HD_CF_REG
7
Received ILAS configuration on
Lane 0. S is the number of
samples per converter per frame
cycle. Link information received
on Lane 0 as specified in Section
8.3 of JESD204B. Value in register
is S − 1.
HD_RD
Received ILAS configuration on
Lane 0. HD is the high density
format. Refer to Section 5.1.3 of
JESD204B standard. Link
information received on Lane 0
as specified in Section 8.3 of
JESD204B.
0 Low density mode.
0x0
R
0x0
R
1 High density mode.
[6:5] RESERVED
Reserved.
0x0
R
[4:0] CF_RD
Received ILAS configuration on
0x0
Lane 0. CF is the number of
control words per frame clock
period per link. Link information
received on Lane 0 as specified in
Section 8.3 of JESD204B. CF is
always 0 on this device.
R
0x40B RES1_REG
[7:0] RES1_RD
Received ILAS configuration on
Lane 0. Reserved Field 1. Link
information received on Lane 0
as specified in Section 8.3 of
JESD204B.
0x0
R
0x40C RES2_REG
[7:0] RES2_RD
Received ILAS configuration on
Lane 0. Reserved Field 2. Link
information received on Lane 0
as specified in Section 8.3 of
JESD204B.
0x0
R
0x40D CHECKSUM0_REG
[7:0] LL_FCHK0
Received checksum during ILAS
on Lane 0. Checksum for Lane 0.
Link information received on
Lane 0 as specified in Section 8.3
of JESD204B.
0x0
R
Rev. A | Page 106 of 136
Data Sheet
AD9164
Hex.
Addr. Name
Bits Bit Name
0x40E COMPSUM0_REG
[7:0] LL_FCMP0
Computed checksum on Lane 0. 0x0
Computed checksum for Lane 0.
The JESD204B Rx computes the
checksum of the link information
received on Lane 0 as specified in
Section 8.3 of JESD204B. The
computation method is set by
the CHECKSUM_MODE bit
(Register 0x300, Bit 6) and must
match the likewise calculated
checksum in Register 0x40D.
R
0x412 LID1_REG
[7:5] RESERVED
Reserved.
0x0
R
[4:0] LL_LID1
Received ILAS LID configuration 0x0
on Lane 1. Lane identification for
Lane 1. Link information received
on Lane 0 as specified in
Section 8.3 of JESD204B.
R
0x415 CHECKSUM1_REG
[7:0] LL_FCHK1
Received checksum during ILAS
on lane 1. Checksum for Lane 1.
Link information received on
Lane 0 as specified in Section 8.3
of JESD204B.
0x0
R
0x416 COMPSUM1_REG
[7:0] LL_FCMP1
Computed checksum on Lane 1. 0x0
Computed checksum for Lane 1
(see description for Register 0x40E).
R
0x41A LID2_REG
[7:5] RESERVED
Reserved.
0x0
R
[4:0] LL_LID2
Received ILAS LID configuration 0x0
on Lane 2. Lane identification for
Lane 2.
R
0x41D CHECKSUM2_REG
[7:0] LL_FCHK2
Received checksum during ILAS
on Lane 2. Checksum for Lane 2.
0x0
R
0x41E COMPSUM2_REG
[7:0] LL_FCMP2
Computed checksum on Lane 2. 0x0
Computed checksum for Lane 2
(see description for Register 0x40E).
R
0x422 LID3_REG
[7:5] RESERVED
Reserved.
0x0
R
[4:0] LL_LID3
Received ILAS LID configuration 0x0
on Lane 3. Lane identification for
Lane 3.
R
0x425 CHECKSUM3_REG
[7:0] LL_FCHK3
Received checksum during ILAS
on Lane 3. Checksum for Lane 3.
0x0
R
0x426 COMPSUM3_REG
[7:0] LL_FCMP3
Computed checksum on Lane 3. 0x0
Computed checksum for Lane 3
(see description for Register 0x40E).
R
0x42A LID4_REG
[7:5] RESERVED
Reserved.
0x0
R
[4:0] LL_LID4
Received ILAS LID configuration 0x0
on Lane 4. Lane identification for
Lane 4.
R
0x42D CHECKSUM4_REG
[7:0] LL_FCHK4
Received checksum during ILAS
on Lane 4. Checksum for Lane 4.
0x0
R
0x42E COMPSUM4_REG
[7:0] LL_FCMP4
Computed checksum on Lane 4. 0x0
Computed checksum for Lane 4
(see description for Register 0x40E).
R
0x432 LID5_REG
[7:5] RESERVED
Reserved.
0x0
R
[4:0] LL_LID5
Received ILAS LID configuration 0x0
on Lane 5. Lane identification for
Lane 5.
R
0x435 CHECKSUM5_REG
[7:0] LL_FCHK5
Received checksum during ILAS
on lane 5. Checksum for Lane 5.
0x0
R
0x436 COMPSUM5_REG
[7:0] LL_FCMP5
Computed checksum on Lane 5. 0x0
Computed checksum for Lane 5
(see description for Register 0x40E).
R
Settings
Rev. A | Page 107 of 136
Description
Reset Access
AD9164
Data Sheet
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x43A LID6_REG
[7:5] RESERVED
Reserved.
0x0
R
[4:0] LL_LID6
Received ILAS LID configuration 0x0
on Lane 6. Lane identification for
Lane 6.
R
0x43D CHECKSUM6_REG
[7:0] LL_FCHK6
Received checksum during ILAS
on Lane 6. Checksum for Lane 6.
0x0
R
0x43E COMPSUM6_REG
[7:0] LL_FCMP6
Computed checksum on Lane 6. 0x0
Computed checksum for Lane 6
(see description for Register 0x40E).
R
0x442 LID7_REG
[7:5] RESERVED
Reserved.
0x0
R
[4:0] LL_LID7
Received ILAS LID configuration 0x0
on Lane 7. Lane identification for
Lane 7.
R
0x445 CHECKSUM7_REG
[7:0] LL_FCHK7
Received checksum during ILAS
on Lane 7. Checksum for Lane 7.
0x0
R
0x446 COMPSUM7_REG
[7:0] LL_FCMP7
Computed checksum on Lane 5. 0x0
Computed checksum for Lane 7
(see description for Register 0x40E).
R
0x450 ILS_DID
[7:0] DID
Device ( link) identification number. 0x0
DID is the device ID number. Link
information received on Lane 0
as specified in Section 8.3 of
JESD204B. Must be set to the
value read in Register 0x400. This
signal must only be programmed
while the QBD is held in soft
reset (Register 0x475, Bit 3), and
must not be changed during
normal operation.
R/W
0x451 ILS_BID
[7:0] BID
Bank ID, extension to DID. This
0x0
signal must only be programmed
while the QBD is held in soft
reset (Register 0x475, Bit 3), and
must not be changed during
normal operation.
R/W
0x452 ILS_LID0
7
RESERVED
Reserved.
R
6
ADJDIR
Direction to adjust DAC LMFC
0x0
(Subclass 2 only). ADJDIR is the
direction to adjust DAC LMFC. Link
information received on Lane 0
as specified in Section 8.3 of
JESD204B. This signal must only
be programmed while the QBD is
held in soft reset (Register 0x475,
Bit 3), and must not be changed
during normal operation.
R/W
5
PHADJ
Phase adjustment to DAC
0x0
(Subclass 2 only). PHADJ is the
phase adjustment request to the
DAC. Link information received on
Lane 0 as specified in Section 8.3
of JESD204B. This signal must only
be programmed while the QBD is
held in soft reset (Register 0x475,
Bit 3), and must not be changed
during normal operation.
R/W
Lane identification number
0x0
(within link). LID0 is the lane
identification for Lane 0. Link
information received on Lane 0
as specified in Section 8.3 of
JESD204B. This signal must only
be programmed while the QBD is
held in soft reset (Register 0x475,
Bit 3), and must not be changed
during normal operation.
R/W
Settings
[4:0] LID0
Rev. A | Page 108 of 136
0x0
Data Sheet
AD9164
Hex.
Addr. Name
Bits Bit Name
0x453 ILS_SCR_L
7
Settings
SCR
Description
Reset Access
Scramble enable. SCR is the Rx
0x1
descrambling enable. This signal
must only be programmed while
the QBD is held in soft reset
(Register 0x475, Bit 3), and must
not be changed during normal
operation.
0 Descrambling is disabled.
R/W
1 Descrambling is enabled.
[6:5] RESERVED
Reserved.
0x0
R
[4:0] L
Number of lanes per converter
(minus 1). L is the number of lanes
per converter device. Settings of
1, 2, 3, 4, 6, and 8 are valid. Refer
to Table 15 and Table 16.
0x7
R
0x454 ILS_F
[7:0] F
Number of octets per frame
0x0
(minus 1). This value of F is not
used to soft configure the QBD.
Register CTRLREG1 is used to soft
configure the QBD.
R
0x455 ILS_K
[7:5] RESERVED
Reserved.
R
[4:0] K
Number of frames per
0x1F
multiframe (minus 1). K is the
number of frames per
multiframe. On this device, all
modes use K = 32 (value in
register is K − 1). This signal must
only be programmed while the
QBD is held in soft reset (Register
0x475, Bit 3), and must not be
changed during normal
operation.
0x0
R/W
01111 16 frames per multiframe.
11111 32 frames per multiframe.
0x456 ILS_M
[7:0] M
Number of converters per device 0x1
(minus 1). M is the number of
converters/device. Settings of 1
and 2 are valid. Refer to Table 15
and Table 16.
R
0x457 ILS_CS_N
[7:6] CS
Number of control bits per
sample. CS is the number of
control bits per sample. Must be
set to 0. Control bits are not
supported.
0x0
R
5
Reserved.
0x0
R
Converter resolution (minus 1). N 0xF
is the converter resolution. Must
be set to 16 (0x0F).
R
RESERVED
[4:0] N
0x458 ILS_NP
[7:5] SUBCLASSV
Device subclass version.
0x0
SUBCLASSV is the device subclass
version. This signal must only be
programmed while the QBD is
held in soft reset (Register 0x475,
Bit 3), and must not be changed
during normal operation.
000 Subclass 0.
R/W
001 Subclass 1.
010 Subclass 2 (not supported).
[4:0] NP
Total number of bits per sample 0xF
(minus 1) NP is the total number
of bits per sample. Must be set to
16 (0x0F). Refer to Table 15 and
Table 16.
Rev. A | Page 109 of 136
R
AD9164
Data Sheet
Hex.
Addr. Name
Bits Bit Name
0x459 ILS_S
[7:5] JESDV
Settings
Description
JESD204x version. JESDV is the
JESD204x version. This signal
must only be programmed while
the QBD is held in soft reset
(Register 0x475, Bit 3), and must
not be changed during normal
operation.
000 JESD204A.
Reset Access
0x0
R/W
001 JESD204B.
[4:0] S
0x45A ILS_HD_CF
7
Number of samples per
0x1
converter per frame cycle (minus
1). S is the number of samples
per converter per frame cycle.
Settings of 1 and 2 are valid.
Refer to Table 15 and Table 16.
HD
High density format. HD is the
high density mode. Refer to
Section 5.1.3 of JESD204B
standard.
0 Low density mode.
R
0x1
R
1 High density mode.
[6:5] RESERVED
Reserved.
0x0
R
[4:0] CF
Number of control bits per
sample. CF is the number of
control words per frame clock
period per link. Must be set to 0.
Control bits are not supported.
0x0
R
0x45B ILS_RES1
[7:0] RES1
Reserved. Reserved Field 1. This 0x0
signal must only be programmed
while the QBD is held in soft
reset (Register 0x475, Bit 3), and
must not be changed during
normal operation.
R/W
0x45C ILS_RES2
[7:0] RES2
Reserved. Reserved Field 2. This 0x0
signal must only be programmed
while the QBD is held in soft
reset (Register 0x475, Bit 3), and
must not be changed during
normal operation.
R/W
0x45D ILS_CHECKSUM
[7:0] FCHK0
Link configuration checksum.
0x0
Checksum for Lane 0. The checksum for the values programmed
into Register 0x450 to
Register 0x45C must be calculated
according to Section 8.3 of the
JESD204B specification and written
to this register (SUM(Register 0x450
to Register 0x45C) % 256). This
signal must only be programmed
while the QBD is held in soft
reset (Register 0x475, Bit 3), and
must not be changed during
normal operation.
R/W
0x46C LANE_DESKEW
7
Interlane deskew status for
Lane 7 (ignore this output when
NO_ILAS = 1).
0x0
R
0x0
R
ILD7
0 Deskew failed.
1 Deskew achieved.
6
ILS6
Initial lane synchronization
status for Lane 6 (ignore this
output when NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
Rev. A | Page 110 of 136
Data Sheet
Hex.
Addr. Name
AD9164
Bits Bit Name
5
Settings
ILD5
Description
Reset Access
Interlane deskew status for
Lane 5 (ignore this output when
NO_ILAS = 1).
0x0
R
0x0
R
0 Deskew failed.
1 Deskew achieved.
4
ILD4
Interlane deskew status for
Lane 4 (ignore this output when
NO_ILAS = 1).
0 Deskew failed.
1 Deskew achieved.
3
ILD3
Interlane deskew status for
Lane 3 (ignore this output when
NO_ILAS = 1).
0 Deskew failed.
1 Deskew achieved.
0x0
R
2
ILD2
Interlane deskew status for
Lane 2 (ignore this output when
NO_ILAS = 1).
0 Deskew failed.
1 Deskew achieved.
0x0
R
1
ILD1
Interlane deskew status for
Lane 1 (ignore this output when
NO_ILAS = 1).
0 Deskew failed.
0x0
R
0
ILD0
0x0
R
7
BDE7
Bad disparity error status for Lane 7. 0x0
R
1 Deskew achieved.
Interlane deskew status for Lane 0
(ignore this output when
NO_ILAS = 1).
0 Deskew failed.
1 Deskew achieved.
0x46D BAD_DISPARITY
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
6
BDE6
Bad disparity error status for Lane 6. 0x0
R
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
5
BDE5
Bad disparity errors status for
Lane 5.
0x0
R
Bad disparity error status for Lane 4. 0x0
R
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
4
BDE4
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
3
BDE3
2
BDE2
Bad disparity error status for Lane 3. 0x0
0 Error count < ETH[7:0] value.
R
1 Error count ≥ ETH[7:0] value.
Bad disparity error status for Lane 2. 0x0
0 Error count < ETH[7:0] value.
R
1 Error count ≥ ETH[7:0] value.
1
BDE1
Bad disparity error status for Lane 1. 0x0
R
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
0
BDE0
Bad disparity error status for Lane 0. 0x0
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
Rev. A | Page 111 of 136
R
AD9164
Data Sheet
Hex.
Addr. Name
Bits Bit Name
0x46E NOT_IN_TABLE
7
NIT7
Not in table error status for Lane 7.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
0x0
R
6
NIT6
Not in table error status for Lane 6.
0 Error count < ETH[7:0] value.
0x0
R
5
NIT5
Not in table errors status for Lane 5. 0x0
0 Error count < ETH[7:0] value.
R
4
NIT4
Settings
Description
Reset Access
1 Error count ≥ ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
Not in table error status for Lane 4.
0x0
R
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
3
NIT3
Not in table error status for Lane 3.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
0x0
R
2
NIT2
Not in table error status for Lane 2.
0 Error count < ETH[7:0] value.
0x0
R
1
NIT1
0x0
R
1 Error count ≥ ETH[7:0] value.
Not in table error status for Lane 1.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
0x46F UNEXPECTED_KCHAR
0
NIT0
Not in table error status for Lane 0.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
0x0
R
7
UEK7
Unexpected K character error
status for Lane 7.
0x0
R
0x0
R
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
6
UEK6
Unexpected K character error
status for Lane 6.
0 Error count < ETH[7:0] value.
5
UEK5
Unexpected K character error
status for Lane 5.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
0x0
R
4
UEK4
Unexpected K character error
status for Lane 4.
0x0
R
0x0
R
0x0
R
0x0
R
1 Error count ≥ ETH[7:0] value.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
3
UEK3
Unexpected K character error
status for Lane 3.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
2
UEK2
1
UEK1
Unexpected K character error
status for Lane 2.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
Unexpected K character error
status for Lane 1.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
Rev. A | Page 112 of 136
Data Sheet
Hex.
Addr. Name
AD9164
Bits Bit Name
0
UEK0
7
CGS7
6
CGS6
Settings
Description
Unexpected K character error
status for Lane 0.
0 Error count < ETH[7:0] value.
Reset Access
0x0
R
Code group sync status for
Lane 7.
0 Synchronization lost.
1 Synchronization achieved.
0x0
R
Code group sync status for
Lane 6.
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
1 Error count ≥ ETH[7:0] value.
0x470 CODE_GRP_SYNC
0 Synchronization lost.
1 Synchronization achieved.
5
CGS5
4
CGS4
3
CGS3
Code group sync status for
Lane 5.
0 Synchronization lost.
1 Synchronization achieved.
Code group sync status for
Lane 4.
0 Synchronization lost.
1 Synchronization achieved.
Code group sync status for
Lane 3.
0 Synchronization lost.
1 Synchronization achieved.
2
CGS2
Code group sync status for
Lane 2.
0 Synchronization lost.
1 Synchronization achieved.
1
CGS1
Code group sync status for
Lane 1.
0 Synchronization lost.
0
CGS0
Code group sync status for
Lane 0.
0 Synchronization lost.
1 Synchronization achieved.
0x0
R
7
FS7
Frame sync status for Lane 7
(ignore this output when
NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
0x0
R
6
FS6
Frame sync status for Lane 6
(ignore this output when
NO_ILAS = 1).
0 Synchronization lost.
0x0
R
5
FS5
0x0
R
4
FS4
0x0
R
1 Synchronization achieved.
0x471 FRAME_SYNC
1 Synchronization achieved.
Frame sync status for Lane 5
(ignore this output when
NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
Frame sync status for Lane 4
(ignore this output when
NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
Rev. A | Page 113 of 136
AD9164
Hex.
Addr. Name
Data Sheet
Bits Bit Name
3
Settings
FS3
Description
Reset Access
Frame sync status for Lane 3
(ignore this output when
NO_ILAS = 1).
0x0
R
0x0
R
0 Synchronization lost.
1 Synchronization achieved.
2
FS2
Frame sync status for Lane 2
(ignore this output when
NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
0x472 GOOD_CHECKSUM
1
FS1
Frame sync status for Lane 1
(ignore this output when
NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
0x0
R
0
FS0
Frame sync status for Lane 0
(ignore this output when
NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
0x0
R
7
CKS7
Computed checksum status for
Lane 7 (ignore this output when
NO_ILAS = 1).
0 Checksum is incorrect.
0x0
R
6
CKS6
0x0
R
5
CKS5
0x0
R
4
CKS4
0x0
R
3
CKS3
0x0
R
0x0
R
0x0
R
1 Checksum is correct.
Computed checksum status for
Lane 6 (ignore this output when
NO_ILAS = 1).
0 Checksum is incorrect.
1 Checksum is correct.
Computed checksum status for
Lane 5 (ignore this output when
NO_ILAS = 1).
0 Checksum is incorrect.
1 Checksum is correct.
Computed checksum status for
Lane 4 (ignore this output when
NO_ILAS = 1).
0 Checksum is incorrect.
1 Checksum is correct.
Computed checksum status for
Lane 3 (ignore this output when
NO_ILAS = 1).
0 Checksum is incorrect.
1 Checksum is correct.
2
CKS2
Computed checksum status for
Lane 2 (ignore this output when
NO_ILAS = 1).
0 Checksum is incorrect.
1 Checksum is correct.
1
CKS1
Computed checksum status for
Lane 1 (ignore this output when
NO_ILAS = 1).
0 Checksum is incorrect.
1 Checksum is correct.
Rev. A | Page 114 of 136
Data Sheet
Hex.
Addr. Name
AD9164
Bits Bit Name
0
Settings
CKS0
Description
Reset Access
Computed checksum status for
Lane 0 (ignore this output when
NO_ILAS = 1).
0x0
R
0x0
R
0 Checksum is incorrect.
1 Checksum is correct.
0x473 INIT_LANE_SYNC
7
ILS7
Initial lane synchronization
status for Lane 7 (ignore this
output when NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
6
ILS6
Initial lane synchronization
status for Lane 6 (ignore this
output when NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
0x0
R
5
ILS5
Initial lane synchronization
status for Lane 5 (ignore this
output when NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
0x0
R
4
ILS4
Initial lane synchronization
status for Lane 4 (ignore this
output when NO_ILAS = 1).
0 Synchronization lost.
0x0
R
3
ILS3
0x0
R
2
ILS2
0x0
R
1
ILS1
0x0
R
0
ILS0
0x0
R
1 Synchronization achieved.
Initial lane synchronization
status for Lane 3 (ignore this
output when NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
Initial lane synchronization
status for Lane 2 (ignore this
output when NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
Initial lane synchronization
status for Lane 1 (ignore this
output when NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
Initial lane synchronization
status for Lane 0 (ignore this
output when NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
0x475 CTRLREG0
7
RX_DIS
Level input: disable deframer
0x0
receiver when this input = 1. This
signal must only be programmed
while the QBD is held in soft
reset (Register 0x475, Bit 3), and
must not be changed during
normal operation.
1 Disable character replacement of
/A/ and /F/ control characters at
the end of received frames and
multiframes.
0 Enables the substitution.
Rev. A | Page 115 of 136
R/W
AD9164
Hex.
Addr. Name
Data Sheet
Bits Bit Name
6
Settings
CHAR_REPL_DIS
Description
Reset Access
When this input = 1, character
0x0
replacement at the end of
frame/multiframe is disabled.
This signal must only be
programmed while the QBD is
held in soft reset (Register 0x475,
Bit 3), and must not be changed
during normal operation.
R/W
[5:4] RESERVED
Reserved.
0x0
R
3
Soft reset. Active high
synchronous reset. Resets all
hardware to power-on state.
0x0
R/W
SOFTRST
1 Disables the deframer reception.
0 Enable deframer logic.
0x476 CTRLREG1
2
FORCESYNCREQ
Command from application to
0x0
assert a sync request (SYNCOUT).
Active high.
R/W
1
RESERVED
Reserved.
R
0
REPL_FRM_ENA
When this level input is set, it
0x1
enables replacement of frames
received in error. This signal
must only be programmed while
the QBD is held in soft reset
(Register 0x475, Bit 3), and must
not be changed during normal
operation.
R/W
Reserved.
R
[7:5] RESERVED
4
QUAL_RDERR
0x0
0x0
Error reporting behavior for
0x1
concurrent NIT and RD errors.
This signal must only be
programmed while the QBD is
held in soft reset (Register 0x475,
Bit 3), and must not be changed
during normal operation.
0 NIT has no effect on RD error.
R/W
1 NIT error masks concurrent RD
error.
3
DEL_SCR
Alternative descrambler enable. 0x0
(see JESD204B Section 5.2.4) This
signal must only be programmed
while the QBD is held in soft
reset (Register 0x475, Bit 3), and
must not be changed during
normal operation.
1 Descrambling begins at Octet 2
of user data.
0 Descrambling begins at Octet 0
of user data. This is the common
usage.
R/W
2
CGS_SEL
Determines the QBD behavior
0x1
after code group sync has been
achieved. This signal must only
be programmed while the QBD is
held in soft reset (Register 0x475,
Bit 3), and must not be changed
during normal operation.
0 After code group sync is achieved,
the QBD asserts SYNCOUT only if
there are sufficient disparity errors
as per the JESD204B standard.
1 After code group sync is achieved,
if a /K/ is followed by any character
other than an /R/ or another /K/,
QBD asserts SYNCOUT.
R/W
Rev. A | Page 116 of 136
Data Sheet
Hex.
Addr. Name
AD9164
Bits Bit Name
1
Settings
NO_ILAS
Description
Reset Access
This signal must only be
0x0
programmed while the QBD is
held in soft reset (Register 0x475,
Bit 3), and must not be changed
during normal operation.
R/W
1 For single-lane operation, ILAS is
omitted. Code group sync is
followed by user data.
0 Code group sync is followed by
ILAS. For multilane operation,
NO_ILAS must always be set to 0.
0
FCHK_N
Checksum calculation method.
0x0
This signal must only be
programmed while the QBD is
held in soft reset (Register 0x475,
Register 3), and must not be
changed during normal
operation.
R/W
0 Calculate checksum by summing
individual fields (this more
closely matches the definition of
the checksum field in the
JESD204B standard.
1 Calculate checksum by summing
the registers containing the
packed fields (this setting is
provided in case the framer of
another vendor performs the
calculation with this method).
0x477 CTRLREG2
7
ILS_MODE
Data link layer test mode. This
0x0
signal must only be programmed
while the QBD is held in soft
reset (Register 0x475, Bit 3), and
must not be changed during
normal operation.
0 Normal mode.
1 Code group sync pattern is
followed by a perpetual ILAS
sequence.
6
RESERVED
Reserved.
5
REPDATATEST
Repetitive data test enable, using 0x0
JTSPAT pattern. To enable the
test, ILS_MODE must = 0. This
signal must only be programmed
while the QBD is held in soft
reset (Register 0x475, Bit 3), and
must not be changed during
normal operation.
R/W
4
QUETESTERR
Queue test error mode. This
0x0
signal must only be programmed
while the QBD is held in soft
reset (Register 0x475, Bit 3), and
must not be changed during
normal operation.
R/W
0 Simultaneous errors on multiple
lanes are reported as one error.
1 Detected errors from all lanes are
trapped in a counter and
sequentially signaled on
SYNCOUT.
Rev. A | Page 117 of 136
0x0
R/W
R
AD9164
Hex.
Addr. Name
Data Sheet
Bits Bit Name
3
Settings
AR_ECNTR
Description
Reset Access
Automatic reset of error counter. 0x0
The error counter that causes
assertion of SYNCOUT is automatically reset to 0 when AR_ECNTR =
1. All other counters are
unaffected. This signal must only
be programmed while the QBD is
held in soft reset (Register 0x475,
Bit 3), and must not be changed
during normal operation.
R/W
R
[2:0] RESERVED
Reserved.
0x478 KVAL
[7:0] KSYNC
Number of 4 × K multiframes
0x1
during ILS. F is the number of
octets per frame. Settings of 1, 2,
and 4 are valid. Refer to Table 15
and Table 16. This signal must
only be programmed while the
QBD is held in soft reset (Register
0x475, Bit 3), and must not be
changed during normal
operation.
0x0
R/W
0x47C ERRORTHRES
[7:0] ETH
0xFF
Error threshold value. Bad
disparity, NIT disparity, and
unexpected K character errors
are counted and compared to
the error threshold value. When
the count is equal, either an IRQ
is generated or SYNCOUT± is
asserted per the mask register
settings or both. Function is
performed in all lanes. This signal
must only be programmed while
the QBD is held in soft reset
(Register 0x475, Bit 3), and must
not be changed during normal
operation.
R/W
0x47D SYNC_ASSERT_MASK
[7:3] RESERVED
Reserved.
0x0
R
[2:0] SYNC_ASSERT_MASK
SYNCOUT assertion enable mask
for BD, NIT, and UEK error
conditions. Active high,
SYNCOUT assertion enable mask
for BD, NIT, and UEK error
conditions, respectively. When
an error counter, in any lane, has
reached the error threshold
count, ETH[7:0], and the
corresponding SYNC_ASSERT_
MASK bit is set, SYNCOUT is
asserted. The mask bits are as
follows. Note that the bit
sequence is reversed with
respect to the other error count
controls and the error counters.
0x7
R/W
Bit 2 = bad disparity error (BDE).
Bit 1 = not in table error (NIT).
Bit 0 = unexpected K (UEK)
character error.
0x480 ECNT_CTRL0
[7:6] RESERVED
Reserved.
0x0
R
[5:3] ECNT_ENA0
Error counter enable for Lane 0.
Counters of each lane are
addressed as follows:
0x7
R/W
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
Rev. A | Page 118 of 136
Data Sheet
Hex.
Addr. Name
AD9164
Bits Bit Name
Settings
[2:0] ECNT_RST0
Description
Reset Access
Error counters enable for Lane 0,
active high. Counters of each
lane are addressed as follows:
0x7
R/W
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
0x481 ECNT_CTRL1
[7:6] RESERVED
Reserved.
0x0
R
[5:3] ECNT_ENA1
Error counters enable for Lane 1,
active high. Counters of each
lane are addressed as follows:
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
0x7
R/W
[2:0] ECNT_RST1
Error counters enable for Lane 1,
active high. Counters of each
lane are addressed as follows:
Bit 2 = unexpected K (UEK)
character error.
0x7
R/W
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
0x482 ECNT_CTRL2
[7:6] RESERVED
Reserved.
0x0
R
[5:3] ECNT_ENA2
Error counters enable for Lane 2,
active high. Counters of each
lane are addressed as follows:
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
0x7
R/W
0x7
R/W
Bit 0 = bad disparity error (BDE).
[2:0] ECNT_RST2
Error counters enable for Lane 2,
active high. Counters of each
lane are addressed as follows:
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
0x483 ECNT_CTRL3
[7:6] RESERVED
Reserved.
0x0
R
[5:3] ECNT_ENA3
Error counters enable for Lane 3,
active high. Counters of each
lane are addressed as follows:
0x7
R/W
0x7
R/W
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
[2:0] ECNT_RST3
Error counters enable for Lane 3,
active high. Counters of each
lane are addressed as follows:
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
Rev. A | Page 119 of 136
AD9164
Data Sheet
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x484 ECNT_CTRL4
[7:6] RESERVED
Reserved.
0x0
R
[5:3] ECNT_ENA4
Error counters enable for Lane 4,
active high. Counters of each
lane are addressed as follows:
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
0x7
R/W
[2:0] ECNT_RST4
Error counters enable for Lane 4,
active high. Counters of each
lane are addressed as follows:
Bit 2 = unexpected K (UEK)
character error.
0x7
R/W
Settings
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
0x485 ECNT_CTRL5
[7:6] RESERVED
Reserved.
0x0
R
[5:3] ECNT_ENA5
Error counters enable for Lane 5,
active high. Counters of each
lane are addressed as follows:
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
0x7
R/W
0x7
R/W
Bit 0 = bad disparity error (BDE).
[2:0] ECNT_RST5
Error counters enable for Lane 5,
active high. Counters of each
lane are addressed as follows:
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
0x486 ECNT_CTRL6
[7:6] RESERVED
Reserved.
0x0
R
[5:3] ECNT_ENA6
Error counters enable for Lane 6,
active high. Counters of each
lane are addressed as follows:
0x7
R/W
0x7
R/W
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
[2:0] ECNT_RST6
Error counters enable for Lane 6,
active high. Counters of each
lane are addressed as follows:
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
0x487 ECNT_CTRL7
[7:6] RESERVED
Reserved.
0x0
R
[5:3] ECNT_ENA7
Error counters enable for Lane 7,
active high. Counters of each
lane are addressed as follows:
Bit 2 = unexpected K (UEK)
character error.
0x7
R/W
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
Rev. A | Page 120 of 136
Data Sheet
Hex.
Addr. Name
AD9164
Bits Bit Name
Settings
[2:0] ECNT_RST7
Description
Reset Access
Reset error counters for Lane 7,
active high. Counters of each
lane are addressed as follows:
0x7
R/W
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
0x488 ECNT_TCH0
[7:3] RESERVED
Reserved.
0x0
R
[2:0] ECNT_TCH0
Terminal count hold enable of
error counters for Lane 0. When
set, the designated counter is to
hold the terminal count value of
0xFF when it is reached until the
counter is reset by the user. Otherwise, the designated counter
rolls over. Counters of each lane
are addressed as follows:
0x7
R/W
0x0
R
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
This signal must only be
programmed while the QBD is
held in soft reset (Register 0x475,
Bit 3), and must not be changed
during normal operation.
0x489 ECNT_TCH1
[7:3] RESERVED
Reserved.
[2:0] ECNT_TCH1
Terminal count hold enable of error 0x7
counters for Lane 1. When set, the
designated counter is to hold the
terminal count value of 0xFF when
it is reached until the counter is
reset by the user. Otherwise, the
designated counter rolls over.
Counters of each lane are
addressed as follows:
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
R/W
Bit 0 = bad disparity error (BDE).
This signal must only be
programmed while the QBD is held
in soft reset (Register 0x475, Bit 3),
and must not be changed during
normal operation.
0x48A ECNT_TCH2
[7:3] RESERVED
Reserved.
[2:0] ECNT_TCH2
Terminal count hold enable of
0x7
error counters for Lane 2. When set,
the designated counter is to hold
the terminal count value of 0xFF
when it is reached until the counter
is reset by the user. Otherwise, the
designated counter rolls over.
Counters of each lane are
addressed as follows:
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
Rev. A | Page 121 of 136
0x0
R
R/W
AD9164
Hex.
Addr. Name
Data Sheet
Bits Bit Name
Settings
Description
Reset Access
This signal must only be programmed while the QBD is held in
soft reset (Register 0x475, Bit 3),
and must not be changed during
normal operation.
0x48B ECNT_TCH3
[7:3] RESERVED
Reserved.
[2:0] ECNT_TCH3
Terminal count hold enable of
0x7
error counters for Lane 3. When
set, the designated counter is to
hold the terminal count value of
0xFF when it is reached until the
counter is reset by the user.
Otherwise, the designated counter
rolls over. Counters of each lane are
addressed as follows:
0x0
R
R/W
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
This signal must only be
programmed while the QBD is
held in soft reset (Register 0x475,
Bit 3), and must not be changed
during normal operation.
0x48C ECNT_TCH4
[7:3] RESERVED
Reserved.
[2:0] ECNT_TCH4
Terminal count hold enable of
0x7
error counters for Lane 4. When
set, the designated counter is to
hold the terminal count value of
0xFF when it is reached until the
counter is reset by the user.
Otherwise, the designated counter
rolls over. Counters of each lane are
addressed as follows:
0x0
R
R/W
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
This signal must only be
programmed while the QBD is
held in soft reset (Register 0x475,
Bit 3), and must not be changed
during normal operation.
0x48D ECNT_TCH5
[7:3] RESERVED
Reserved.
[2:0] ECNT_TCH5
Terminal count hold enable of
0x7
error counters for Lane 5. When
set, the designated counter is to
hold the terminal count value of
0xFF when it is reached until the
counter is reset by the user.
Otherwise, the designated counter
rolls over. Counters of each lane are
addressed as follows:
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
This signal must only be
programmed while the QBD is
held in soft reset (Register 0x475,
Bit 3), and must not be changed
during normal operation.
Rev. A | Page 122 of 136
0x0
R
R/W
Data Sheet
AD9164
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x48E ECNT_TCH6
[7:3] RESERVED
Reserved.
0x0
R
[2:0] ECNT_TCH6
Terminal count hold enable of
error counters for Lane 6. When
set, the designated counter is to
hold the terminal count value of
0xFF when it is reached until the
counter is reset by the user.
Otherwise, the designated
counter rolls over. Counters of
each lane are addressed as
follows:
Bit 2 = unexpected K (UEK)
character error.
0x7
R/W
Settings
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
This signal must only be
programmed while the QBD is
held in soft reset (Register 0x475,
Bit 3), and must not be changed
during normal operation.
0x48F ECNT_TCH7
[7:3] RESERVED
Reserved.
0x0
R
[2:0] ECNT_TCH7
Terminal count hold enable of
error counters for Lane 7. When
set, the designated counter is to
hold the terminal count value of
0xFF when it is reached until the
counter is reset by the user.
Otherwise, the designated
counter rolls over. Counters of
each lane are addressed as
follows:
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
0x7
R/W
0x0
R
0x0
R
Terminal count reached indicator 0x0
of error counters for Lane 0. Set
to 1 when the corresponding
counter terminal count value of
0xFF has been reached. Counters
of each lane are addressed as
follows.
Bit 2 = unexpected K (UEK)
character error.
R
This signal must only be
programmed while the QBD is
held in soft reset (Register 0x475,
Bit 3), and must not be changed
during normal operation.
0x490 ECNT_STAT0
[7:4] RESERVED
3
Reserved.
LANE_ENA0
This output indicates if Lane 0 is
enabled.
0 Lane 0 is held in soft reset.
1 Lane 0 is enabled.
[2:0] ECNT_TCR0
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
0x491 ECNT_STAT1
[7:4] RESERVED
Reserved.
0x0
R
3
This output indicates if Lane 1 is
enabled.
0x0
R
LANE_ENA1
0 Lane 1 is held in soft reset.
1 Lane 1 is enabled.
Rev. A | Page 123 of 136
AD9164
Hex.
Addr. Name
Data Sheet
Bits Bit Name
Settings
[2:0] ECNT_TCR1
Description
Reset Access
Terminal count reached indicator 0x0
of error counters for Lane 1. Set
to 1 when the corresponding
counter terminal count value of
0xFF has been reached. Counters
of each lane are addressed as
follows.
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
R
Bit 0 = bad disparity error (BDE).
0x492 ECNT_STAT2
[7:4] RESERVED
0x0
R
0x0
R
[2:0] ECNT_TCR2
Terminal count reached indicator 0x0
of error counters for Lane 2. Set
to 1 when the corresponding
counter terminal count value of
0xFF has been reached. Counters
of each lane are addressed as
follows.
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
R
[7:4] RESERVED
Reserved.
0x0
R
0x0
R
Terminal count reached indicator 0x0
of error counters for Lane 3. Set
to 1 when the corresponding
counter terminal count value of
0xFF has been reached. Counters
of each lane are addressed as
follows:
R
3
Reserved.
LANE_ENA2
This output indicates if Lane 2 is
enabled.
0 Lane 2 is held in soft reset.
1 Lane 2 is enabled.
0x493 ECNT_STAT3
3
LANE_ENA3
This output indicates if Lane 3 is
enabled.
0 Lane 3 is held in soft reset.
1 Lane 3 is enabled.
[2:0] ECNT_TCR3
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
0x494 ECNT_STAT4
[7:4] RESERVED
3
Reserved.
LANE_ENA4
[2:0] ECNT_TCR4
0x0
R
0x0
R
Terminal count reached indicator 0x0
of error counters for Lane 4. Set
to 1 when the corresponding
counter terminal count value of
0xFF has been reached. Counters
of each lane are addressed as
follows:
R
This output indicates if Lane 4 is
enabled.
0 Lane 4 is held in soft reset.
1 Lane 4 is enabled.
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
Rev. A | Page 124 of 136
Data Sheet
AD9164
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x495 ECNT_STAT5
[7:4] RESERVED
Reserved.
0x0
R
3
This output indicates if Lane 5 is
enabled.
0x0
R
Terminal count reached indicator 0x0
of error counters for Lane 5. Set
to 1 when the corresponding
counter terminal count value of
0xFF has been reached. Counters
of each lane are addressed as
follows:
R
Settings
LANE_ENA5
0 Lane 5 is held in soft reset.
1 Lane 5 is enabled.
[2:0] ECNT_TCR5
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
0x496 ECNT_STAT6
[7:4] RESERVED
Reserved.
0x0
R
3
This output indicates if Lane 6 is
enabled.
0x0
R
Terminal count reached indicator 0x0
of error counters for Lane 6. Set
to 1 when the corresponding
counter terminal count value of
0xFF has been reached. Counters
of each lane are addressed as
follows:
Bit 2 = unexpected K (UEK)
character error.
Bit 1 = not in table error (NIT).
R
LANE_ENA6
0 Lane 6 is held in soft reset.
1 Lane 6 is enabled.
[2:0] ECNT_TCR6
Bit 0 = bad disparity error (BDE).
0x497 ECNT_STAT7
[7:4] RESERVED
3
Reserved.
LANE_ENA7
0x0
R
0x0
R
Terminal count reached indicator 0x0
of error counters for Lane 7. Set
to 1 when the corresponding
counter terminal count value of
0xFF has been reached. Counters
of each lane are addressed as
follows:
Bit 2 = unexpected K (UEK)
character error.
R
This output indicates if Lane 7 is
enabled.
0 Lane 7 is held in soft reset.
1 Lane 7 is enabled.
[2:0] ECNT_TCR7
Bit 1 = not in table error (NIT).
Bit 0 = bad disparity error (BDE).
0x4B0 LINK_STATUS0
7
BDE0
6
NIT0
5
UEK0
Bad disparity errors status for
Lane 0.
0 Error count < ETH[7:0] value.
0x0
R
0x0
R
0x0
R
1 Error count ≥ ETH[7:0] value.
Not in table errors status for
Lane 0.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
Unexpected K character errors
status for Lane 0.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
Rev. A | Page 125 of 136
AD9164
Hex.
Addr. Name
Data Sheet
Bits Bit Name
4
Settings
ILD0
Description
Reset Access
Interlane deskew status for
Lane 0 (ignore this output when
NO_ILAS = 1).
0x0
R
0x0
R
0 Deskew failed.
1 Deskew achieved.
3
ILS0
Initial lane synchronization
status for Lane 0 (ignore this
output when NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
2
CKS0
Computed checksum status for
Lane 0 (ignore this output when
NO_ILAS = 1).
0 Checksum is incorrect.
1 Checksum is correct.
0x0
R
1
FS0
Frame sync status for Lane 0
(ignore this output when
NO_ILAS = 1).
0 Synchronization lost.
0x0
R
0
CGS0
0x0
R
0x0
R
0x0
R
0x0
R
1 Synchronization achieved.
Code group sync status for
Lane 0.
0 Synchronization lost.
1 Synchronization achieved.
0x4B1 LINK_STATUS1
7
BDE1
Bad Disparity errors status for
Lane 1.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
6
NIT1
Not in table errors status for
Lane 1.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
5
UEK1
Unexpected K character errors
status for Lane 1.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
4
ILD1
Interlane deskew status for
Lane 1 (ignore this output when
NO_ILAS = 1).
0 Deskew failed.
1 Deskew achieved.
0x0
R
3
ILS1
Initial lane synchronization
status for Lane 1 (ignore this
output when NO_ILAS = 1).
0 Synchronization lost.
0x0
R
2
CKS1
0x0
R
1
FS1
0x0
R
1 Synchronization achieved.
Computed checksum status for
Lane 1 (ignore this output when
NO_ILAS = 1).
0 Checksum is incorrect.
1 Checksum is correct.
Frame sync status for Lane 1
(ignore this output when
NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
Rev. A | Page 126 of 136
Data Sheet
Hex.
Addr. Name
AD9164
Bits Bit Name
0
CGS1
7
BDE2
6
NIT2
Settings
Description
Code group sync status for
Lane 1.
0 Synchronization lost.
Reset Access
0x0
R
Bad Disparity errors status for
Lane 2.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
0x0
R
Not in table errors status for
Lane 2.
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
1 Synchronization achieved.
0x4B2 LINK_STATUS2
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
5
UEK2
4
ILD2
Unexpected K character errors
status for Lane 2.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
Interlane deskew status for
Lane 2 (ignore this output when
NO_ILAS = 1).
0 Deskew failed.
1 Deskew achieved.
3
ILS2
Initial lane synchronization
status for Lane 2 (ignore this
output when NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
2
CKS2
Computed checksum status for
Lane 2 (ignore this output when
NO_ILAS = 1).
0 Checksum is incorrect.
1 Checksum is correct.
1
FS2
Frame sync status for Lane 2
(ignore this output when
NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
0
CGS2
Code group sync status for
Lane 2.
0 Synchronization lost.
1 Synchronization achieved.
0x4B3 LINK_STATUS3
7
BDE3
6
NIT3
5
UEK3
Bad Disparity errors status for
Lane 3.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
Not in table errors status for
Lane 3.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
Unexpected K character errors
status for Lane 3.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
4
ILD3
Interlane deskew status for
Lane 3 (ignore this output when
NO_ILAS = 1).
0 Deskew failed.
1 Deskew achieved.
Rev. A | Page 127 of 136
AD9164
Hex.
Addr. Name
Data Sheet
Bits Bit Name
3
Settings
ILS3
Description
Reset Access
Initial lane synchronization
status for Lane 3 (ignore this
output when NO_ILAS = 1).
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0 Synchronization lost.
1 Synchronization achieved.
2
CKS3
Computed checksum status for
Lane 3 (ignore this output when
NO_ILAS = 1).
0 Checksum is incorrect.
1 Checksum is correct.
1
FS3
0
CGS3
Frame sync status for Lane 3
(ignore this output when
NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
Code group sync status for
Lane 3.
0 Synchronization lost.
1 Synchronization achieved.
0x4B4 LINK_STATUS4
7
BDE4
Bad Disparity errors status for
Lane 4.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
6
NIT4
5
UEK4
Not in table errors status for
Lane 4.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
Unexpected K character errors
status for Lane 4.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
4
ILD4
Interlane deskew status for
Lane 4 (ignore this output when
NO_ILAS = 1).
0 Deskew failed.
1 Deskew achieved.
3
ILS4
Initial lane synchronization
status for Lane 4 (ignore this
output when NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
0x0
R
2
CKS4
Computed checksum status for
Lane 4 (ignore this output when
NO_ILAS = 1).
0 Checksum is incorrect.
0x0
R
1
FS4
0x0
R
0
CGS4
0x0
R
1 Checksum is correct.
Frame sync status for Lane 4
(ignore this output when
NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
Code group sync status for
Lane 4.
0 Synchronization lost.
1 Synchronization achieved.
Rev. A | Page 128 of 136
Data Sheet
AD9164
Hex.
Addr. Name
Bits Bit Name
0x4B5 LINK_STATUS5
7
BDE5
6
NIT5
5
UEK5
Settings
Description
Bad disparity errors status for
Lane 5.
0 Error count < ETH[7:0] value.
Reset Access
0x0
R
0x0
R
0x0
R
0x0
R
1 Error count ≥ ETH[7:0] value.
Not in table errors status for
Lane 5.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
Unexpected K character errors
status for Lane 5.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
4
ILD5
Interlane deskew status for
Lane 5 (ignore this output when
NO_ILAS = 1).
0 Deskew failed.
1 Deskew achieved.
3
ILS5
Initial lane synchronization
status for Lane 5 (ignore this
output when NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
0x0
R
2
CKS5
Computed checksum status for
Lane 5 (ignore this output when
NO_ILAS = 1).
0 Checksum is incorrect.
1 Checksum is correct.
0x0
R
1
FS5
Frame sync status for Lane 5
(ignore this output when
NO_ILAS = 1).
0 Synchronization lost.
0x0
R
0
CGS5
0x0
R
0x0
R
0x0
R
1 Synchronization achieved.
Code group sync status for
Lane 5.
0 Synchronization lost.
1 Synchronization achieved.
0x4B6 LINK_STATUS6
7
BDE6
6
NIT6
Bad Disparity errors status for
Lane 6.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
Not in table errors status for
Lane 6.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
5
UEK6
Unexpected K character errors
status for Lane 6.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
0x0
R
4
ILD6
Interlane deskew status for Lane 6
(ignore this output when
NO_ILAS = 1).
0 Deskew failed.
1 Deskew achieved.
0x0
R
3
ILS6
Initial lane synchronization
status for Lane 6 (ignore this
output when NO_ILAS = 1).
0 Synchronization lost.
0x0
R
1 Synchronization achieved.
Rev. A | Page 129 of 136
AD9164
Hex.
Addr. Name
Data Sheet
Bits Bit Name
2
Settings
CKS6
Description
Reset Access
Computed checksum status for
Lane 6 (ignore this output when
NO_ILAS = 1).
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0x0
R
0 Checksum is incorrect.
1 Checksum is correct.
1
FS6
Frame sync status for Lane 6
(ignore this output when
NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
0
CGS6
Code group sync status for
Lane 6.
0 Synchronization lost.
1 Synchronization achieved.
0x4B7 LINK_STATUS7
7
BDE7
6
NIT7
5
UEK7
Bad Disparity errors status for
Lane 7.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
Not in table errors status for
Lane 7.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
Unexpected K character errors
status for Lane 7.
0 Error count < ETH[7:0] value.
1 Error count ≥ ETH[7:0] value.
4
ILD7
Interlane deskew status for
Lane 7 (ignore this output when
NO_ILAS = 1).
0 Deskew failed.
1 Deskew achieved.
3
ILS7
Initial lane synchronization
status for Lane 7 (ignore this
output when NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
2
CKS7
Computed checksum status for
Lane 7 (ignore this output when
NO_ILAS = 1).
0 Checksum is incorrect.
1 Checksum is correct.
1
FS7
0
CGS7
Frame sync status for Lane 7
(ignore this output when
NO_ILAS = 1).
0 Synchronization lost.
1 Synchronization achieved.
Code group sync status for
Lane 7.
0 Synchronization lost.
1 Synchronization achieved.
0x4B8 JESD_IRQ_ENABLEA
7
EN_BDE
Bad disparity error counter.
0x0
R/W
6
EN_NIT
Not in table error counter.
0x0
R/W
5
EN_UEK
Unexpected K error counter.
0x0
R/W
4
EN_ILD
Interlane deskew.
0x0
R/W
3
EN_ILS
Initial lane sync.
0x0
R/W
Rev. A | Page 130 of 136
Data Sheet
Hex.
Addr. Name
0x4B9 JESD_IRQ_ENABLEB
0x4BA JESD_IRQ_STATUSA
0x4BB JESD_IRQ_STATUSB
0x800 HOPF_CTRL
AD9164
Bits Bit Name
Settings
Description
Reset Access
2
EN_CKS
Good checksum. This is an
0x0
interrupt that compares two
checksums: the checksum that
the transmitter sent over the link
during the ILAS, and the
checksum that the receiver
calculated from the ILAS data
that the transmitter sent over the
link. Note that the checksum IRQ
never at any time looks at the
checksum that is programmed
over the SPI into Register 0x45D.
The checksum IRQ only looks at
the data sent by the transmitter,
and never looks at any data
programmed via the SPI.
R/W
1
EN_FS
Frame sync.
0x0
R/W
0
EN_CGS
Code group sync.
0x0
R/W
[7:1] RESERVED
Reserved.
0x0
R
0
EN_ILAS
Configuration mismatch
0x0
(checked for Lane 0 only). The
ILAS IRQ compares the two sets
of ILAS data that the receiver has:
the ILAS data sent over the
JESD204B link by the transmitter,
and the ILAS data programmed
into the receiver via the SPI
(Register 0x450 to Register 0x45D).
If the data differs, the IRQ is
triggered. Note that all of the
ILAS data (including the
checksum) is compared.
R/W
7
IRQ_BDE
Bad disparity error counter.
0x0
R/W
6
IRQ_NIT
Not in table error counter.
0x0
R/W
5
IRQ_UEK
Unexpected K error counter.
0x0
R/W
4
IRQ_ILD
Interlane deskew.
0x0
R/W
3
IRQ_ILS
Initial lane sync.
0x0
R/W
2
IRQ_CKS
Good checksum.
0x0
R/W
1
IRQ_FS
Frame sync.
0x0
R/W
0
IRQ_CGS
Code group sync.
0x0
R/W
[7:1] RESERVED
Reserved.
0x0
R
0
Configuration mismatch
(checked for Lane 0 only).
0x0
R/W
Frequency switch mode.
0x0
00 Phase continuous switch.
Changes frequency tuning word,
and the phase accumulator
continues to accumulate to the
new FTW.
01 Phase discontinuous switch.
Changes the frequency tuning
word and resets the phase
accumulator.
10 Reserved.
R/W
IRQ_ILAS
[7:6] HOPF_MODE
5
RESERVED
Reserved.
0x0
R
[4:0] HOPF_SEL
Hopping frequency selection
control. Enter the number of the
FTW to select the output of that
NCO.
0x0
R/W
0x806 HOPF_FTW1_0
[7:0] HOPF_FTW1[7:0]
Hopping frequency FTW1.
0x0
R/W
0x807 HOPF_FTW1_1
[7:0] HOPF_FTW1[15:8]
Hopping frequency FTW1.
0x0
R/W
Rev. A | Page 131 of 136
AD9164
Data Sheet
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x808 HOPF_FTW1_2
[7:0] HOPF_FTW1[23:16]
Hopping frequency FTW1
0x0
R/W
0x809 HOPF_FTW1_3
[7:0] HOPF_FTW1[31:24]
Hopping frequency FTW1
0x0
R/W
0x80A HOPF_FTW2_0
[7:0] HOPF_FTW2[7:0]
Hopping frequency FTW2
0x0
R/W
0x80B HOPF_FTW2_1
[7:0] HOPF_FTW2[15:8]
Hopping frequency FTW2
0x0
R/W
0x80C HOPF_FTW2_2
[7:0] HOPF_FTW2[23:16]
Hopping frequency FTW2
0x0
R/W
0x80D HOPF_FTW2_3
[7:0] HOPF_FTW2[31:24]
Hopping frequency FTW2
0x0
R/W
0x80E HOPF_FTW3_0
[7:0] HOPF_FTW3[7:0]
Hopping frequency FTW3
0x0
R/W
Settings
0x80F HOPF_FTW3_1
[7:0] HOPF_FTW3[15:8]
Hopping frequency FTW3
0x0
R/W
0x810 HOPF_FTW3_2
[7:0] HOPF_FTW3[23:16]
Hopping frequency FTW3
0x0
R/W
0x811 HOPF_FTW3_3
[7:0] HOPF_FTW3[31:24]
Hopping frequency FTW3
0x0
R/W
0x812 HOPF_FTW4_0
[7:0] HOPF_FTW4[7:0]
Hopping frequency FTW4
0x0
R/W
0x813 HOPF_FTW4_1
[7:0] HOPF_FTW4[15:8]
Hopping frequency FTW4
0x0
R/W
0x814 HOPF_FTW4_2
[7:0] HOPF_FTW4[23:16]
Hopping frequency FTW4
0x0
R/W
0x815 HOPF_FTW4_3
[7:0] HOPF_FTW4[31:24]
Hopping frequency FTW4
0x0
R/W
0x816 HOPF_FTW5_0
[7:0] HOPF_FTW5[7:0]
Hopping frequency FTW5
0x0
R/W
0x817 HOPF_FTW5_1
[7:0] HOPF_FTW5[15:8]
Hopping frequency FTW5
0x0
R/W
0x818 HOPF_FTW5_2
[7:0] HOPF_FTW5[23:16]
Hopping frequency FTW5
0x0
R/W
0x819 HOPF_FTW5_3
[7:0] HOPF_FTW5[31:24]
Hopping frequency FTW5
0x0
R/W
0x81A HOPF_FTW6_0
[7:0] HOPF_FTW6[7:0]
Hopping frequency FTW6
0x0
R/W
0x81B HOPF_FTW6_1
[7:0] HOPF_FTW6[15:8]
Hopping frequency FTW6
0x0
R/W
0x81C HOPF_FTW6_2
[7:0] HOPF_FTW6[23:16]
Hopping frequency FTW6
0x0
R/W
0x81D HOPF_FTW6_3
[7:0] HOPF_FTW6[31:24]
Hopping frequency FTW6
0x0
R/W
0x81E HOPF_FTW7_0
[7:0] HOPF_FTW7[7:0]
Hopping frequency FTW7
0x0
R/W
0x81F HOPF_FTW7_1
[7:0] HOPF_FTW7[15:8]
Hopping frequency FTW7
0x0
R/W
0x820 HOPF_FTW7_2
[7:0] HOPF_FTW7[23:16]
Hopping frequency FTW7
0x0
R/W
0x821 HOPF_FTW7_3
[7:0] HOPF_FTW7[31:24]
Hopping frequency FTW7
0x0
R/W
0x822 HOPF_FTW8_0
[7:0] HOPF_FTW8[7:0]
Hopping frequency FTW8
0x0
R/W
0x823 HOPF_FTW8_1
[7:0] HOPF_FTW8[15:8]
Hopping frequency FTW8
0x0
R/W
0x824 HOPF_FTW8_2
[7:0] HOPF_FTW8[23:16]
Hopping frequency FTW8
0x0
R/W
0x825 HOPF_FTW8_3
[7:0] HOPF_FTW8[31:24]
Hopping frequency FTW8
0x0
R/W
0x826 HOPF_FTW9_0
[7:0] HOPF_FTW9[7:0]
Hopping frequency FTW9
0x0
R/W
0x827 HOPF_FTW9_1
[7:0] HOPF_FTW9[15:8]
Hopping frequency FTW9
0x0
R/W
0x828 HOPF_FTW9_2
[7:0] HOPF_FTW9[23:16]
Hopping frequency FTW9
0x0
R/W
0x829 HOPF_FTW9_3
[7:0] HOPF_FTW9[31:24]
Hopping frequency FTW9
0x0
R/W
0x82A HOPF_FTW10_0
[7:0] HOPF_FTW10[7:0]
Hopping frequency FTW10
0x0
R/W
0x82B HOPF_FTW10_1
[7:0] HOPF_FTW10[15:8]
Hopping frequency FTW10
0x0
R/W
0x82C HOPF_FTW10_2
[7:0] HOPF_FTW10[23:16]
Hopping frequency FTW10
0x0
R/W
0x82D HOPF_FTW10_3
[7:0] HOPF_FTW10[31:24]
Hopping frequency FTW10
0x0
R/W
0x82E HOPF_FTW11_0
[7:0] HOPF_FTW11[7:0]
Hopping frequency FTW11
0x0
R/W
0x82F HOPF_FTW11_1
[7:0] HOPF_FTW11[15:8]
Hopping frequency FTW11
0x0
R/W
0x830 HOPF_FTW11_2
[7:0] HOPF_FTW11[23:16]
Hopping frequency FTW11
0x0
R/W
0x831 HOPF_FTW11_3
[7:0] HOPF_FTW11[31:24]
Hopping frequency FTW11
0x0
R/W
0x832 HOPF_FTW12_0
[7:0] HOPF_FTW12[7:0]
Hopping frequency FTW12
0x0
R/W
0x833 HOPF_FTW12_1
[7:0] HOPF_FTW12[15:8]
Hopping frequency FTW12
0x0
R/W
Rev. A | Page 132 of 136
Data Sheet
AD9164
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x834 HOPF_FTW12_2
[7:0] HOPF_FTW12[23:16]
Hopping frequency FTW12
0x0
R/W
0x835 HOPF_FTW12_3
[7:0] HOPF_FTW12[31:24]
Hopping frequency FTW12
0x0
R/W
0x836 HOPF_FTW13_0
[7:0] HOPF_FTW13[7:0]
Hopping frequency FTW13
0x0
R/W
0x837 HOPF_FTW13_1
[7:0] HOPF_FTW13[15:8]
Hopping frequency FTW13
0x0
R/W
0x838 HOPF_FTW13_2
[7:0] HOPF_FTW13[23:16]
Hopping frequency FTW13
0x0
R/W
0x839 HOPF_FTW13_3
[7:0] HOPF_FTW13[31:24]
Hopping frequency FTW13
0x0
R/W
0x83A HOPF_FTW14_0
[7:0] HOPF_FTW14[7:0]
Hopping frequency FTW14
0x0
R/W
0x83B HOPF_FTW14_1
[7:0] HOPF_FTW14[15:8]
Hopping frequency FTW14
0x0
R/W
0x83C HOPF_FTW14_2
[7:0] HOPF_FTW14[23:16]
Hopping frequency FTW14
0x0
R/W
0x83D HOPF_FTW14_3
[7:0] HOPF_FTW14[31:24]
Hopping frequency FTW14
0x0
R/W
Settings
0x83E HOPF_FTW15_0
[7:0] HOPF_FTW15[7:0]
Hopping frequency FTW15
0x0
R/W
0x83F HOPF_FTW15_1
[7:0] HOPF_FTW15[15:8]
Hopping frequency FTW15
0x0
R/W
0x840 HOPF_FTW15_2
[7:0] HOPF_FTW15[23:16]
Hopping frequency FTW15
0x0
R/W
0x841 HOPF_FTW15_3
[7:0] HOPF_FTW15[31:24]
Hopping frequency FTW15
0x0
R/W
0x842 HOPF_FTW16_0
[7:0] HOPF_FTW16[7:0]
Hopping frequency FTW16
0x0
R/W
0x843 HOPF_FTW16_1
[7:0] HOPF_FTW16[15:8]
Hopping frequency FTW16
0x0
R/W
0x844 HOPF_FTW16_2
[7:0] HOPF_FTW16[23:16]
Hopping frequency FTW16
0x0
R/W
0x845 HOPF_FTW16_3
[7:0] HOPF_FTW16[31:24]
Hopping frequency FTW16
0x0
R/W
0x846 HOPF_FTW17_0
[7:0] HOPF_FTW17[7:0]
Hopping frequency FTW17
0x0
R/W
0x847 HOPF_FTW17_1
[7:0] HOPF_FTW17[15:8]
Hopping frequency FTW17
0x0
R/W
0x848 HOPF_FTW17_2
[7:0] HOPF_FTW17[23:16]
Hopping frequency FTW17
0x0
R/W
0x849 HOPF_FTW17_3
[7:0] HOPF_FTW17[31:24]
Hopping frequency FTW17
0x0
R/W
0x84A HOPF_FTW18_0
[7:0] HOPF_FTW18[7:0]
Hopping frequency FTW18
0x0
R/W
0x84B HOPF_FTW18_1
[7:0] HOPF_FTW18[15:8]
Hopping frequency FTW18
0x0
R/W
0x84C HOPF_FTW18_2
[7:0] HOPF_FTW18[23:16]
Hopping frequency FTW18
0x0
R/W
0x84D HOPF_FTW18_3
[7:0] HOPF_FTW18[31:24]
Hopping frequency FTW18
0x0
R/W
0x84E HOPF_FTW19_0
[7:0] HOPF_FTW19[7:0]
Hopping frequency FTW19
0x0
R/W
0x84F HOPF_FTW19_1
[7:0] HOPF_FTW19[15:8]
Hopping frequency FTW19
0x0
R/W
0x850 HOPF_FTW19_2
[7:0] HOPF_FTW19[23:16]
Hopping frequency FTW19
0x0
R/W
0x851 HOPF_FTW19_3
[7:0] HOPF_FTW19[31:24]
Hopping frequency FTW19
0x0
R/W
0x852 HOPF_FTW20_0
[7:0] HOPF_FTW20[7:0]
Hopping frequency FTW20
0x0
R/W
0x853 HOPF_FTW20_1
[7:0] HOPF_FTW20[15:8]
Hopping frequency FTW20
0x0
R/W
0x854 HOPF_FTW20_2
[7:0] HOPF_FTW20[23:16]
Hopping frequency FTW20
0x0
R/W
0x855 HOPF_FTW20_3
[7:0] HOPF_FTW20[31:24]
Hopping frequency FTW20
0x0
R/W
0x856 HOPF_FTW21_0
[7:0] HOPF_FTW21[7:0]
Hopping frequency FTW21
0x0
R/W
0x857 HOPF_FTW21_1
[7:0] HOPF_FTW21[15:8]
Hopping frequency FTW21
0x0
R/W
0x858 HOPF_FTW21_2
[7:0] HOPF_FTW21[23:16]
Hopping frequency FTW21
0x0
R/W
0x859 HOPF_FTW21_3
[7:0] HOPF_FTW21[31:24]
Hopping frequency FTW21
0x0
R/W
0x85A HOPF_FTW22_0
[7:0] HOPF_FTW22[7:0]
Hopping frequency FTW22
0x0
R/W
0x85B HOPF_FTW22_1
[7:0] HOPF_FTW22[15:8]
Hopping frequency FTW22
0x0
R/W
0x85C HOPF_FTW22_2
[7:0] HOPF_FTW22[23:16]
Hopping frequency FTW22
0x0
R/W
0x85D HOPF_FTW22_3
[7:0] HOPF_FTW22[31:24]
Hopping frequency FTW22
0x0
R/W
0x85E HOPF_FTW23_0
[7:0] HOPF_FTW23[7:0]
Hopping frequency FTW23
0x0
R/W
0x85F HOPF_FTW23_1
[7:0] HOPF_FTW23[15:8]
Hopping frequency FTW23
0x0
R/W
Rev. A | Page 133 of 136
AD9164
Data Sheet
Hex.
Addr. Name
Bits Bit Name
Description
Reset Access
0x860 HOPF_FTW23_2
[7:0] HOPF_FTW23[23:16]
Hopping frequency FTW23
0x0
R/W
0x861 HOPF_FTW23_3
[7:0] HOPF_FTW23[31:24]
Hopping frequency FTW23
0x0
R/W
0x862 HOPF_FTW24_0
[7:0] HOPF_FTW24[7:0]
Hopping frequency FTW24
0x0
R/W
0x863 HOPF_FTW24_1
[7:0] HOPF_FTW24[15:8]
Hopping frequency FTW24
0x0
R/W
0x864 HOPF_FTW24_2
[7:0] HOPF_FTW24[23:16]
Hopping frequency FTW24
0x0
R/W
0x865 HOPF_FTW24_3
[7:0] HOPF_FTW24[31:24]
Hopping frequency FTW24
0x0
R/W
0x866 HOPF_FTW25_0
[7:0] HOPF_FTW25[7:0]
Hopping frequency FTW25
0x0
R/W
0x867 HOPF_FTW25_1
[7:0] HOPF_FTW25[15:8]
Hopping frequency FTW25
0x0
R/W
0x868 HOPF_FTW25_2
[7:0] HOPF_FTW25[23:16]
Hopping frequency FTW25
0x0
R/W
0x869 HOPF_FTW25_3
[7:0] HOPF_FTW25[31:24]
Hopping frequency FTW25
0x0
R/W
Settings
0x86A HOPF_FTW26_0
[7:0] HOPF_FTW26[7:0]
Hopping frequency FTW26
0x0
R/W
0x86B HOPF_FTW26_1
[7:0] HOPF_FTW26[15:8]
Hopping frequency FTW26
0x0
R/W
0x86C HOPF_FTW26_2
[7:0] HOPF_FTW26[23:16]
Hopping frequency FTW26
0x0
R/W
0x86D HOPF_FTW26_3
[7:0] HOPF_FTW26[31:24]
Hopping frequency FTW26
0x0
R/W
0x86E HOPF_FTW27_0
[7:0] HOPF_FTW27[7:0]
Hopping frequency FTW27
0x0
R/W
0x86F HOPF_FTW27_1
[7:0] HOPF_FTW27[15:8]
Hopping frequency FTW27
0x0
R/W
0x870 HOPF_FTW27_2
[7:0] HOPF_FTW27[23:16]
Hopping frequency FTW27
0x0
R/W
0x871 HOPF_FTW27_3
[7:0] HOPF_FTW27[31:24]
Hopping frequency FTW27
0x0
R/W
0x872 HOPF_FTW28_0
[7:0] HOPF_FTW28[7:0]
Hopping frequency FTW28
0x0
R/W
0x873 HOPF_FTW28_1
[7:0] HOPF_FTW28[15:8]
Hopping frequency FTW28
0x0
R/W
0x874 HOPF_FTW28_2
[7:0] HOPF_FTW28[23:16]
Hopping frequency FTW28
0x0
R/W
0x875 HOPF_FTW28_3
[7:0] HOPF_FTW28[31:24]
Hopping frequency FTW28
0x0
R/W
0x876 HOPF_FTW29_0
[7:0] HOPF_FTW29[7:0]
Hopping frequency FTW29
0x0
R/W
0x877 HOPF_FTW29_1
[7:0] HOPF_FTW29[15:8]
Hopping frequency FTW29
0x0
R/W
0x878 HOPF_FTW29_2
[7:0] HOPF_FTW29[23:16]
Hopping frequency FTW29
0x0
R/W
0x879 HOPF_FTW29_3
[7:0] HOPF_FTW29[31:24]
Hopping frequency FTW29
0x0
R/W
0x87A HOPF_FTW30_0
[7:0] HOPF_FTW30[7:0]
Hopping frequency FTW30
0x0
R/W
0x87B HOPF_FTW30_1
[7:0] HOPF_FTW30[15:8]
Hopping frequency FTW30
0x0
R/W
0x87C HOPF_FTW30_2
[7:0] HOPF_FTW30[23:16]
Hopping frequency FTW30
0x0
R/W
0x87D HOPF_FTW30_3
[7:0] HOPF_FTW30[31:24]
Hopping frequency FTW30
0x0
R/W
0x87E HOPF_FTW31_0
[7:0] HOPF_FTW31[7:0]
Hopping frequency FTW31
0x0
R/W
0x87F HOPF_FTW31_1
[7:0] HOPF_FTW31[15:8]
Hopping frequency FTW31
0x0
R/W
0x880 HOPF_FTW31_2
[7:0] HOPF_FTW31[23:16]
Hopping frequency FTW31
0x0
R/W
0x881 HOPF_FTW31_3
[7:0] HOPF_FTW31[31:24]
Hopping frequency FTW31
0x0
R/W
Rev. A | Page 134 of 136
Data Sheet
AD9164
OUTLINE DIMENSIONS
8.05
8.00 SQ
7.95
5.85
BSC
A1 BALL
CORNER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
A1 BALL
CORNER
1
A
B
C
D
E
7.00
REF SQ
F
G
H
5.895
BSC
J
0.50
BSC
K
L
M
N
P
R
0.50
REF
TOP VIEW
DETAIL A
0.35
0.30
0.25
DETAIL A
0.24
REF
0.22 NOM
0.15 MIN
0.35
COPLANARITY
0.30
0.08
0.25
BALL DIAMETER
PKG-004576
SEATING
PLANE
10-28-2014-A
0.86 MAX
0.76 MOM
BOTTOM VIEW
Figure 143. 165-Ball Chip Scale Package Ball Grid Array [CSP_BGA]
(BC-165-1)
Dimensions shown in millimeters
A1 BALL
CORNER
11.05
11.00 SQ
10.95
A1 BALL
PAD CORNER
1.285
BSC
13 12 11 10 9 8 7 6 5 4 3 2 1
A
5.935
BSC
B
C
D
E
F
G
H
J
K
L
M
N
9.60
REF SQ
0.80
BSC
TOP VIEW
2.405 BSC
BOTTOM VIEW
0.70
REF
5.890 BSC
DETAIL A
*0.95 MAX
PKG-004675
SEATING
PLANE
DETAIL A
0.45
0.40
0.35
BALL DIAMETER
0.31 NOM
0.21 MIN
COPLANARITY
0.12
*COMPLIANT TO JEDEC STANDARDS MO-275-FFAC-1 WITH THE
EXCEPTION OF PACKAGE HEIGHT AND THICKNESS.
Figure 144. 169-Ball Chip Scale Package Ball Grid Array [CSP_BGA]
(BC-169-2)
Dimensions shown in millimeters
Rev. A | Page 135 of 136
07-10-2015-A
0.35
0.30
0.25
AD9164
Data Sheet
ORDERING GUIDE
Model1
AD9164BBCZ
AD9164BBCZRL
AD9164BBCAZ
AD9164BBCAZRL
AD9164BBCA
AD9164BBCARL
AD9164-FMC-EBZ
AD9164-FMCB-EBZ
AD9164-FMCC-EBZ
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
165-Ball Chip Scale Package Ball Grid Array [CSP_BGA]
165-Ball Chip Scale Package Ball Grid Array [CSP_BGA]
169-Ball Chip Scale Package Ball Grid Array [CSP_BGA]
169-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
169-Ball Chip Scale Package Ball Grid Array [CSP_BGA]
169-Ball Chip Scale Package Ball Grid Array [CSP_BGA]
Evaluation Board For 8 × 8 mm Package with High Accuracy Balance Balun
Evaluation Board For 8 × 8 mm Package with Balun and Match
Optimized For Wider Output Bandwidth
Evaluation Board
Z = RoHS Compliant Part.
©2016–2017 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D14414-0-1/17(A)
Rev. A | Page 136 of 136
Package Option
BC-165-1
BC-165-1
BC-169-2
BC-169-2
BC-169-2
BC-169-2
Similar pages