MPD MB4012S24RW Mb4000rw sery Datasheet

MB4000RW Series
Compact, 1 x 2 Inch
40W, 2:1 Input Range
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
Input
Parameter
Conditions
Min.
12 VDC Input
24 VDC Input
48 VDC Input
12 VDC Input
24 VDC Input
48 VDC Input
LC Filter
See Note 1
• 40W Output Power
• 2:1 Input Voltage Range
Input Start Voltage
• 1,500 VDC Isolation
• Single & Dual Outputs
Input Shutdown Voltage
• Efficiency to 91%
Input Filter
Start-Up Time
• Compact 1 x 2 Inch Case
• Wide Temp Operation
Max.
9.0
18.0
36.0
Units
VDC
8.3
16.5
33.0
VDC
30
mS
Output
Parameter
Conditions
• Industry Standard Pin-Out Output Voltage Accuracy
• Low Cost
Typ.
Output Voltage Balance
Line Regulation
Load Regulation, Min Load to Full Load
Cross Regulation
Ripple & Noise, See Note 3
Transient Recovery Time, See Note 4
Transient Response Deviation
Temperature Coefficient
Over Temperature Protection
Output Power Protection
Output Short Circuit, See Note 5
Min.
Dual Output , Balanced Loads
VIN = Min to Max
Single Output Models
Dual Output Models
See Note 2
3.3 & 5.0 Vout Models
12, 15 & 24 Vout Models
Dual Output Models
Typ.
100
150
150
250
±3.0
25% Load Step Change
Max.
±1.0
±2.0
±0.5
±0.5
±1.0
±5.0
±5.0
±0.02
Shutdown Temperature
110
150
Continuous (Autorecovery)
Units
%
%
%
%
%
mV P - P
mV P - P
mV P - P
µSec
%
%/°C
°C
%
General
Parameter
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
Conditions
60 Seconds
500 VDC
100 kHz, 1V
See Note 6
Min.
1,500
1,000
Typ.
Max.
1,500
320
Units
VDC
M⍀
pF
kHz
Environmental
Parameter
Operating Temperature Range,
Ambient Without Heatsink
Operating Temperature Range,
Ambient With Heatsink
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Physical
Case Size, See Note On Page 4
Case Material
Weight
Conditions
MB40xxS-03RW
MB40xxS-05RW, -12RW, -15RW, -24RW
MB40xxD-xxRW
MB40xxS-03RW
MB40xxS-05RW, -12RW, -15RW, -24RW
MB40xxD-xxRW
Case
Min.
Typ.
-40
+25
-40
+25
-50
Free Air Convection
RH, Non-condensing
Max.
+66
+46
+40
+73
+57
+52
+105
+125
Units
95
%
°C
°C
°C
°C
2.0 x 1.0 x 0.40 Inches (50.8 x 25.4 x 10.2 mm)
Metal with Non-Conductive Base
1.06 Oz (30g)
Reliability Specifications
Parameter
MTBF
Conditions
MIL HDBK 217F, 25°C, Gnd Benign
Min.
328
Typ.
Max.
Units
kHours
Conditions
12 VDC Input
24 VDC Input
48 VDC Input
1.5 mm From Case For 10 Sec
Min.
-0.7
-0.7
-0.7
Typ.
Max.
25.0
50.0
100.0
260.0
Units
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
VDC
°C
www.micropowerdirect.com
Model Selection Guide
Model
Number
MB4012S-03RW
MB4012S-05RW
MB4012S-12RW
MB4012S-15RW
MB4012S-24RW
MB4012D-12RW
MB4012D-15RW
MB4024S-03RW
MB4024S-05RW
MB4024S-12RW
MB4024S-15RW
MB4024S-24RW
MB4024D-12RW
MB4024D-15RW
MB4048S-03RW
MB4048S-05RW
MB4048S-12RW
MB4048S-15RW
MB4048S-24RW
MB4048D-12RW
MB4048D-15RW
Input
Voltage (VDC)
Current (mA)
Voltage
Nominal
Range
Full-Load No-Load (VDC)
12
9.0 - 18.0
2,470
120
3.3
12
9.0 - 18.0
3,750
160
5.0
12
9.0 - 18.0
3,750
160
12.0
12
9.0 - 18.0
3,700
150
15.0
12
9.0 - 18.0
3,670
160
24.0
12
9.0 - 18.0
3,790
70
±12.0
12
9.0 - 18.0
3,790
60
±15.0
24
18.0 - 36.0
1,220
75
3.3
24
18.0 - 36.0
1,830
80
5.0
24
18.0 - 36.0
1,830
85
12.0
24
18.0 - 36.0
1,830
75
15.0
24
18.0 - 36.0
1,835
85
24.0
24
18.0 - 36.0
1,870
50
±12.0
24
18.0 - 36.0
1,870
45
±15.0
48
36.0 - 75.0
610
40
3.3
48
36.0 - 75.0
920
50
5.0
48
36.0 - 75.0
910
50
12.0
48
36.0 - 75.0
910
50
15.0
48
36.0 - 75.0
918
50
24.0
48
36.0 - 75.0
940
65
±12.0
48
36.0 - 75.0
940
65
±15.0
Output
Current
Current
(mA, Max)
(mA, Min)
8,000
8,000
3,330
2,670
1,670
±1,670
±1,330
8,000
8,000
3,330
2,670
1,670
±1,670
±1,330
8,000
8,000
3,330
2,670
1,670
±1,670
±1,330
0
0
0
0
0
±145
±110
0
0
0
0
0
±145
±110
0
0
0
0
0
±145
±110
Efficiency
(%, Typ)
Over
Fuse
Voltage Capacitive
Rating
Load
Protection (µF Max)
Slow-Blow
(VDC)
89
89
89
90
91
88
88
90
91
91
91
91
89
89
90
91
92
92
91
89
89
3.9
6.2
15.0
18.0
30.0
±15.0
±18.0
3.9
6.2
15.0
18.0
30.0
±15.0
±18.0
3.9
6.2
15.0
18.0
30.0
±15.0
±18.0
(A)
21,000
13,600
2,400
1,500
600
±1,200
±750
21,000
13,600
2,400
1,500
600
±1,200
±750
21,000
13,600
2,400
1,500
600
±1,200
±750
8.0
8.0
8.0
8.0
8.0
8.0
8.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
Notes:
For heatsink option, add suffix “H” to model number (i.e. MB4012S-05RW-H)
1. Start up time is measured at nominal input and with a constant resistive load.
2. Cross regulation is measured with the output being tested at 100% load. The second output is varied from 25% to 100% load.
3. When measuring output ripple, it is recommended that an external 1 µF capacitor and 10 µF capacitor be connected in parallel from the +VOUT to the -VOUT pins for single output units and from each output to
common for dual output units.
4. Transient recovery is measured to within a 1% error band for a load step change of 25%.
5. Short circuit protection is provided by a “hiccup mode” circuit.
6. The switching frequency for 24 VDC output models is 285 kHz.
7. Operation at no-load will not damage these units. However, they may not meet all specifications if operated below the specified minimum load.
8. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating.
External Trim
MB40xxS-03RW
Trim Down
Vout
VO x 0.99 VO x 0.98 VO x 0.97 VO x 0.96 VO x 0.95 VO x 0.94 VO x 0.93 VO x 0.92 VO x 0.91 VO x 0.90
RDOWN
72.61
32.55
19.20
12.52
8.51
5.84
3.94
2.51
1.39
0.50
Volts
k⍀
Trim Up
Vout
RUP
VO x 1.01 VO x 1.02 VO x 1.03 VO x 1.04 VO x 1.05 VO x 1.06 VO x 1.07 VO x 1.08 VO x 1.09 VO x 1.10
60.84
27.40
16.25
10.68
7.34
5.11
3.51
2.32
1.39
0.65
Volts
k⍀
MB40xxS-05RW
Trim Down
Vout
VO x 0.99 VO x 0.98 VO x 0.97 VO x 0.96 VO x 0.95 VO x 0.94 VO x 0.93 VO x 0.92 VO x 0.91 VO x 0.90
RDOWN
138.88
62.41
36.92
24.18
16.53
11.44
7.79
5.06
2.94
1.24
Volts
k⍀
Trim Up
Vout
RUP
VO x 1.01 VO x 1.02 VO x 1.03 VO x 1.04 VO x 1.05 VO x 1.06 VO x 1.07 VO x 1.08 VO x 1.09 VO x 1.10
106.87
47.76
28.06
18.21
12.30
8.36
5.55
3.44
1.79
0.48
Volts
k⍀
MB40xxS-12RW
Trim Down
Vout
VO x 0.99 VO x 0.98 VO x 0.97 VO x 0.96 VO x 0.95 VO x 0.94 VO x 0.93 VO x 0.92 VO x 0.91 VO x 0.90
RDOWN
413.55
184.55
108.22
70.05
47.15
31.88
20.98
12.80
6.44
1.35
Volts
k⍀
Trim Up
Vout
RUP
VO x 1.01 VO x 1.02 VO x 1.03 VO x 1.04 VO x 1.05 VO x 1.06 VO x 1.07 VO x 1.08 VO x 1.09 VO x 1.10
351.00
157.50
93.00
60.75
41.40
28.50
19.29
12.37
7.00
2.70
Volts
k⍀
On single output units, an external resister may be added to
adjust the converter output.
MB40xxS-15RW
Trim Down
Vout
VO x 0.99 VO x 0.98 VO x 0.97 VO x 0.96 VO x 0.95 VO x 0.94 VO x 0.93 VO x 0.92 VO x 0.91 VO x 0.90
RDOWN
530.73
238.61
141.24
92.56
63.35
43.87
29.96
19.53
11.41
4.92
Volts
k⍀
To adjust the output UP, connect a 5%, 3W resistor between
the minus output pin (5) and the Vout trim pin (6). To adjust
the output DOWN, connect a 5%, 3W resistor between the plus
output pin (4) and the Vout trim pin (6).
Trim Up
Vout
RUP
VO x 1.01 VO x 1.02 VO x 1.03 VO x 1.04 VO x 1.05 VO x 1.06 VO x 1.07 VO x 1.08 VO x 1.09 VO x 1.10
422.77
189.89
112.26
73.44
50.15
34.63
23.54
15.22
8.75
3.58
Volts
k⍀
MB40xxS-24RW
Trim Down
Vout
VO x 0.99 VO x 0.98 VO x 0.97 VO x 0.96 VO x 0.95 VO x 0.94 VO x 0.93 VO x 0.92 VO x 0.91 VO x 0.90
RDOWN
333.39
148.80
87.26
56.50
38.04
25.73
16.94
10.35
5.22
1.12
Volts
k⍀
Trim Up
Vout
RUP
Volts
k⍀
The trim table at right gives suggested resistor values for
this adjustment.
VO x 1.01 VO x 1.02 VO x 1.03 VO x 1.04 VO x 1.05 VO x 1.06 VO x 1.07 VO x 1.08 VO x 1.09 VO x 1.10
243.70
108.50
63.43
40.90
27.38
18.37
11.93
7.10
3.34
0.34
292 Page Street Ste D Stoughton, MA 02072
• TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]
www.micropowerdirect.com
Derating Curves
MB40xxS-03RW Without Heatsink
MB40xxS-03RW With Heatsink
MB40xxS-05RW, -12RW, -15RW, -24RW Without Heatsink
MB40xxS-05RW, -12RW, -15RW, -24RW With Heatsink
MB40xxD-12RW, MB40xxD-15RW Without Heatsink
MB40xxD-12RW, MB40xxD-15RW With Heatsink
EMC Specifications
Parameter
Radiated Emissions
Conducted Emissions
ESD
RS
EFT, See Notes
Surge, See Notes
CS
External Component Connection
Standard
EN 55022
Class A
EN 55022
Class A
EN 61000-4-2 Criteria B; ±8 kV Air, ±6 kV Contact
EN 61000-4-3
Criteria A; 10V/m
EN 61000-4-4
Criteria A; ±2 kV
EN 61000-4-5
Criteria B; ±1 kV
EN 61000-4-6
Criteria A; 10 V/m
Notes:
All units should meet EN 55022 (CE/RE) class A/B with the simple external circuit shown at right. To
meet the requirements of EN 61000-4-4 and EN 61000-4-5, the value of C1 should be changed to
330 µF/200V. Contact the factory for more information.
Standard
Model
C1
MB4012x-xxRW 10 µF/25V 1812 MLCC
EN55022 Class A MB4024x-xxRW 4.7 µF/50V 1812 MLCC
MB4048x-xxRW 2.2 µF/100V 1812 MLCC
MB40xxS-xxRW 3.3 µF/100V 1210/X7S
EN55022 Class B
MB40xxD-xxRW 3.3 µF/100V 1210/X7S
C2
------3.3 µF/100V 1210/X7S
3.3 µF/100V 1210/X7S
L1
------1 mH
1 mH
C3
------3.3 µF/100V 1210/X7S
3.3 µF/100V 1210/X7S
C4
------3.3 µF/100V 1210/X7S
3.3 µF/100V 1210/X7S
C5
C6
1,000 pF/2kV 1808 MLCC 1,000 pF/2kV 1808 MLCC
1,000 pF/2kV 1808 MLCC 1,000 pF/2kV 1808 MLCC
1,000 pF/2kV 1808 MLCC 1,000 pF/2kV 1808 MLCC
1,000 pF/2kV 1808 X7R 1,000 pF/2kV 1808 X7R
1,000 pF/2kV 1808 X7R 1,000 pF/2kV 1808 X7R
Remote On/Off
MicroPower Direct
Parameter
Min
Supply On
Supply Off
Standby Input Current
Control Common
Control Input Current (ON)
Control Input Current (OFF)
3.5
0.0
•
Typ
Max
12.0
1.2
Units
VDC
VDC
2.5
mA
Referenced to Negative Input (pin 2)
0.5
mA
-0.5
mA
292 Page Street Ste D Stoughton, MA 02072
Applying a signal to pin 3 will turn the unit ON/OFF. If the
pin is left open, the unit operates. If grounded, the unit will
shut off. The specifications for the ON/OFF function are
given in the table at left.
• TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]
www.micropowerdirect.com
Mechanical Dimensions
Pin Connections
Mechanical Dimensions: With Optional Heatsink
Pin
1
2
3
4
5
6
Single Output
+Vin
-Vin
Remote On/Off
+Vout
-Vout
Trim
Pin
1
2
3
4
5
6
Dual Output
+Vin
-Vin
Remote On/Off
+Vout
Common
-Vout
For the heatsink option, add suffix “H” to the
model number (i.e. MB4048S-24RW-H)
Notes:
MicroPower Direct
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.02 (±0.50)
• Heatsink is black, anodized aluminum
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]
Similar pages