TI1 INA2180A2QDGKRQ1 Automotive, low- and high-side voltage output, current-sense amplifier Datasheet

Order
Now
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
INA180-Q1, INA2180-Q1, INA4180-Q1
SLYS017 – APRIL 2018
INAx180-Q1 Automotive, Low- and High-Side Voltage Output, Current-Sense Amplifiers
1 Features
3 Description
•
The INA180-Q1, INA2180-Q1, and INA4180-Q1
(INAx180-Q1) current sense amplifiers are designed
for cost-optimized applications. These devices are
part of a family of current-sense amplifiers (also
called current-shunt monitors) that sense voltage
drops across current-sense resistors at commonmode voltages from –0.2 V to +26 V, independent of
the supply voltage. The INAx180-Q1 integrate a
matched resistor gain network in four, fixed-gain
device options: 20 V/V, 50 V/V, 100 V/V, or 200 V/V.
This matched gain resistor network minimizes gain
error and reduces the temperature drift.
1
•
•
•
•
•
•
•
AEC-Q100 Qualified for Automotive Applications
– Temperature Grade 1: –40°C ≤ TA ≤ +125°C
– HBM ESD Classification Level 2
– CDM ESD Classification Level C6
Common-Mode Range (VCM): –0.2 V to +26 V
High Bandwidth: 350 kHz (A1 Devices)
Offset Voltage:
– ±150 µV (Max) at VCM = 0 V
– ±500 µV (Max) at VCM = 12 V
Output Slew Rate: 2 V/µs
Accuracy:
– ±1% Gain Error (Max)
– 1-µV/°C Offset Drift (Max)
Gain Options:
– 20 V/V (A1 Devices)
– 50 V/V (A2 Devices)
– 100 V/V (A3 Devices)
– 200 V/V (A4 Devices)
Quiescent Current: 260 µA Max (INA180)
All these devices operate from a single 2.7-V to 5.5-V
power supply. The single-channel INA180-Q1 draws
a maximum supply current of 260 µA; whereas, the
dual-channel INA2180-Q1 draws a maximum supply
current of 500 µA, and the quad channel draws a
maximum supply current of 900 µA.
The INA180-Q1 is available in a 5-pin, SOT-23
package with two different pin configurations. The
INA2180-Q1 is available in an 8-pin, VSSOP
package. The INA4180-Q1 is available in a 14-pin,
TSSOP package. All device options are specified
over the extended operating temperature range of
–40°C to +125°C.
2 Applications
•
•
•
•
•
Device Information(1)
Motor Control
Battery Monitoring
Power Management
Lighting Control
Overcurrent Detection
PART NUMBER
PACKAGE
BODY SIZE (NOM)
INA180-Q1(2)
SOT-23 (5)
2.90 mm × 1.60 mm
INA2180-Q1
VSSOP (8)
3.00 mm × 3.00 mm
TSSOP (14)
5.00 mm × 4.40 mm
(2)
INA4180-Q1
(1) For all available packages, see the package option addendum
at the end of the datasheet.
(2) INA180-Q1 and INA4180-Q1 are preview devices.
Typical Application Circuit
Bus Voltage, VCM
Up To 26 V
Power Supply, VS
2.7 V to 5.5 V
CBYPASS
0.1 µF
RSENSE
Load
INA4180-Q1 (quad-channel)
INA2180-Q1 (dual-channel)
INA180-Q1 (single-channel)
VS
Microcontroller
IN±
±
OUT
ADC
+
IN+
GND
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. UNLESS OTHERWISE NOTED, this document contains PRODUCTION
DATA.
INA180-Q1, INA2180-Q1, INA4180-Q1
SLYS017 – APRIL 2018
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Device Comparison Table.....................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
3
5
7.1
7.2
7.3
7.4
7.5
7.6
5
5
5
5
6
7
Absolute Maximum Ratings .....................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
9
9.1 Application Information............................................ 19
9.2 Typical Application .................................................. 23
10 Power Supply Recommendations ..................... 25
10.1 Common-Mode Transients Greater Than 26 V .... 25
11 Layout................................................................... 26
11.1 Layout Guidelines ................................................. 26
11.2 Layout Examples................................................... 26
12 Device and Documentation Support ................. 29
12.1
12.2
12.3
12.4
12.5
12.6
12.7
Detailed Description ............................................ 14
8.1
8.2
8.3
8.4
Overview .................................................................
Functional Block Diagrams .....................................
Feature Description.................................................
Device Functional Modes........................................
Application and Implementation ........................ 19
14
14
16
17
Documentation Support ........................................
Related Links ........................................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
29
29
29
29
29
29
29
13 Mechanical, Packaging, and Orderable
Information ........................................................... 30
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
2
DATE
REVISION
NOTES
April 2018
*
Initial release.
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
INA180-Q1, INA2180-Q1, INA4180-Q1
www.ti.com
SLYS017 – APRIL 2018
5 Device Comparison Table
PRODUCT
NUMBER OF CHANNELS
GAIN (V/V)
INA180A1-Q1 (1)
1
20
INA180A2-Q1 (1)
1
50
(1)
1
100
INA180A4-Q1 (1)
1
200
INA180B1-Q1 (1)
1
20
INA180B2-Q1 (1)
1
50
(1)
1
100
INA180B4-Q1 (1)
1
200
INA2180A1-Q1
2
20
INA2180A2-Q1
2
50
INA2180A3-Q1
2
100
INA2180A4-Q1
2
200
INA4180A1-Q1
4
20
INA4180A2-Q1
4
50
INA4180A3-Q1
4
100
INA4180A4-Q1
4
200
INA180A3-Q1
INA180B3-Q1
(1)
INA180A devices use pinout A. INA180B devices use pinout B. See the Pin Configuration and Functions section for more information.
6 Pin Configuration and Functions
INA180-Q1: DBV Package(1)
5-Pin SOT-23 (Pinout A)
Top View
OUT
1
GND
2
IN+
3
5
4
INA180-Q1: DBV Package(1)
5-Pin SOT-23 (Pinout B)
Top View
VS
IN±
IN+
1
GND
2
IN±
3
Not to scale
(1)
5
VS
4
OUT
Not to scale
INA180-Q1 is preview device. See Package Option Addendum at the end of the data sheet for more information.
Pin Functions: INA180-Q1 (Single Channel)
PIN
NAME
SOT-23
Pinout A
SOT-23
Pinout B
TYPE
DESCRIPTION
GND
2
2
Analog
IN–
4
3
Analog input
Current-sense amplifier negative input. For high-side applications,
connect to load side of sense resistor. For low-side applications, connect
to ground side of sense resistor.
IN+
3
1
Analog input
Current-sense amplifier positive input. For high-side applications, connect
to bus-voltage side of sense resistor. For low-side applications, connect
to load side of sense resistor.
OUT
1
4
Analog output
VS
5
5
Analog
Ground
Output voltage
Power supply, 2.7 V to 5.5 V
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
3
INA180-Q1, INA2180-Q1, INA4180-Q1
SLYS017 – APRIL 2018
www.ti.com
INA4180-Q1: PW Package(1)
14-Pin TSSOP
Top View
INA2180-Q1: DGK Package
8-Pin VSSOP
Top View
OUT1
1
8
VS
IN±1
2
7
IN+1
3
GND
4
OUT1
1
14
OUT4
OUT2
IN±1
2
13
IN±4
6
IN±2
IN+1
3
12
IN+4
5
IN+2
VS
4
11
GND
IN+2
5
10
IN+3
IN±2
6
9
IN±3
OUT2
7
8
OUT3
Not to scale
Not to scale
(1)
INA4180-Q1 is preview device. See Package Option Addendum at the end of the data sheet for more information.
Pin Functions: INA2180-Q1 (Dual Channel) and INA4180-Q1 (Quad Channel)
PIN
NAME
TYPE
DESCRIPTION
INA2180-Q1
INA4180-Q1
GND
4
11
Analog
IN–1
2
2
Analog input
Current-sense amplifier negative input for channel 1. For high-side
applications, connect to load side of channel-1 sense resistor. For lowside applications, connect to ground side of channel-1 sense resistor.
IN+1
3
3
Analog input
Current-sense amplifier positive input for channel 1. For high-side
applications, connect to bus-voltage side of channel-1 sense resistor. For
low-side applications, connect to load side of channel-1 sense resistor.
IN–2
6
6
Analog input
Current-sense amplifier negative input for channel 2. For high-side
applications, connect to load side of channel-2 sense resistor. For lowside applications, connect to ground side of channel-2 sense resistor.
IN+2
5
5
Analog input
Current-sense amplifier positive input for channel 2. For high-side
applications, connect to bus-voltage side of channel-2 sense resistor. For
low-side applications, connect to load side of channel-2 sense resistor.
IN–3
—
9
Analog input
Current-sense amplifier negative input for channel 3. For high-side
applications, connect to load side of channel-3 sense resistor. For lowside applications, connect to ground side of channel-3 sense resistor.
IN+3
—
10
Analog input
Current-sense amplifier positive input for channel 3. For high-side
applications, connect to bus-voltage side of channel-3 sense resistor. For
low-side applications, connect to load side of channel-3 sense resistor.
IN–4
—
13
Analog input
Current-sense amplifier negative input for channel 4. For high-side
applications, connect to load side of channel-4 sense resistor. For lowside applications, connect to ground side of channel-4 sense resistor.
IN+4
—
12
Analog input
Current-sense amplifier positive input for channel 4. For high-side
applications, connect to bus-voltage side of channel-4 sense resistor. For
low-side applications, connect to load side of channel-4 sense resistor.
OUT1
1
1
Analog output
Channel 1 output voltage
OUT2
7
7
Analog output
Channel 2 output voltage
OUT3
—
8
Analog output
Channel 3 output voltage
OUT4
—
14
Analog output
Channel 4 output voltage
VS
8
4
Analog
4
Ground
Power supply, 2.7 V to 5.5 V
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
INA180-Q1, INA2180-Q1, INA4180-Q1
www.ti.com
SLYS017 – APRIL 2018
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MIN
MAX
UNIT
6
V
Supply voltage, VS
Analog inputs, IN+, IN– (2) (3)
Differential (VIN+) – (VIN–)
Common-mode (4)
Output voltage
–28
28
GND – 0.3
28
GND – 0.3
VS + 0.3
V
8
mA
150
°C
150
°C
150
°C
Maximum output current, IOUT
Operating free-air temperature, TA
–55
Junction temperature, TJ
Storage temperature, Tstg
(1)
(2)
(3)
(4)
–65
V
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
VIN+ and VIN– are the voltages at the IN+ and IN– pins, respectively.
Sustained operation between 26 V and 28 V for more than a few minutes may cause permanent damage to the device.
Input voltage at any pin can exceed the voltage shown if the current at that pin is limited to 5 mA.
7.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001
(1)
UNIT
±3000
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
V
±1000
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
MIN
NOM
MAX
–0.2
12
26
Operating supply voltage
2.7
5
Operating free-air temperature
–40
VCM
Common-mode input voltage (IN+ and IN–)
VS
TA
UNIT
V
5.5
V
125
°C
7.4 Thermal Information
THERMAL METRIC
(1)
INA180-Q1
(PREVIEW)
INA2180-Q1
INA4180-Q1
(PREVIEW)
DBV (SOT-23)
DGK (VSSOP)
PW (TSSOP)
UNIT
6 PINS
8 PINS
20 PINS
RθJA
Junction-to-ambient thermal resistance
197.1
177.9
115.9
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
95.8
65.6
44.3
°C/W
RθJB
Junction-to-board thermal resistance
53.1
99.3
59.2
°C/W
ψJT
Junction-to-top characterization parameter
23.4
10.5
4.7
°C/W
ψJB
Junction-to-board characterization parameter
52.7
97.9
58.6
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
N/A
N/A
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
5
INA180-Q1, INA2180-Q1, INA4180-Q1
SLYS017 – APRIL 2018
www.ti.com
7.5 Electrical Characteristics
at TA = 25°C, VS = 5 V, VIN+ = 12 V, and VSENSE = VIN+ – VIN– (unless otherwise noted)
PARAMETER
CONDITIONS
MIN
TYP
84
100
MAX
UNIT
INPUT
CMRR
Common-mode rejection ratio,
RTI (1)
VOS
Offset voltage (2), RTI
dVOS/dT
PSRR
VIN+ = 0 V to 26 V, VSENSE = 10 mV,
TA = –40°C to +125°C
dB
±100
±500
VIN+ = 0 V
±25
±150
Offset drift, RTI
TA = –40°C to +125°C
0.2
1
μV/°C
Power-supply rejection ratio, RTI
VS = 2.7 V to 5.5 V, VSENSE = 10 mV
±8
±40
μV/V
VSENSE = 0 mV, VIN+ = 0 V
0.1
VSENSE = 0 mV
80
VSENSE = 0 mV
±0.05
IIB
Input bias current
IIO
Input offset current
μV
µA
µA
OUTPUT
A1 devices
G
Gain
EG
20
A2 devices
50
A3 devices
100
A4 devices
200
Gain error
VOUT = 0.5 V to VS – 0.5 V,
TA = –40°C to +125°C
Gain error vs temperature
TA = –40°C to +125°C
Nonlinearity error
VOUT = 0.5 V to VS – 0.5 V
Maximum capacitive load
No sustained oscillation
V/V
±0.1%
±1%
1.5
20
ppm/°C
±0.01%
1
nF
VOLTAGE OUTPUT (3)
VSP
Swing to VS power-supply rail (4)
VSN
(4)
Swing to GND
RL = 10 kΩ to GND, TA = –40°C to +125°C
(VS) – 0.02
(VS) – 0.03
V
RL = 10 kΩ to GND, TA = –40°C to +125°C
(VGND) +
0.0005
(VGND) +
0.005
V
FREQUENCY RESPONSE
BW
Bandwidth
SR
Slew rate
A1 devices, CLOAD = 10 pF
350
A2 devices, CLOAD = 10 pF
210
A3 devices, CLOAD = 10 pF
150
A4 devices, CLOAD = 10 pF
105
kHz
2
V/µs
40
nV/√Hz
NOISE, RTI
Voltage noise density
POWER SUPPLY
INA180-Q1
(preview)
IQ
Quiescent current
INA2180-Q1
INA4180-Q1
(preview)
(1)
(2)
(3)
(4)
6
VSENSE = 10 mV
197
VSENSE = 10 mV, TA = –40°C to +125°C
VSENSE = 10 mV
300
355
VSENSE = 10 mV, TA = –40°C to +125°C
VSENSE = 10 mV
260
500
520
690
VSENSE = 10 mV, TA = –40°C to +125°C
µA
900
1000
RTI = referred-to-input.
Offset voltage is obtained by linear extrapolation to VSENSE = 0 V with VSENSE = 10% to 90% of full-scale-range.
See Figure 19.
Swing specifications are tested with an overdriven input condition.
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
INA180-Q1, INA2180-Q1, INA4180-Q1
www.ti.com
SLYS017 – APRIL 2018
7.6 Typical Characteristics
-165
-150
-135
-120
-105
-90
-75
-60
-45
-30
-15
0
15
30
45
60
75
90
105
120
135
150
-95
-85
-75
-65
-55
-45
-35
-25
-15
-5
5
15
25
35
45
55
65
75
85
95
105
115
Population
Population
at TA = 25°C, VS = 5 V, and VIN+ = 12 V (unless otherwise noted)
D001
Input Offset Voltage (PV)
Input Offset Voltage (PV)
D002
VIN+ = 0 V
VIN+ = 0 V
Figure 2. Input Offset Voltage Production Distribution A2
-80
-70
-60
-50
-40
-30
-20
-10
0
10
20
30
40
50
60
70
80
90
100
110
120
130
Population
-80
-70
-60
-50
-40
-30
-20
-10
0
10
20
30
40
50
60
70
80
90
100
110
120
130
Population
Figure 1. Input Offset Voltage Production Distribution A1
D003
Input Offset Voltage (PV)
Input Offset Voltage (PV)
VIN+ = 0 V
D004
VIN+ = 0 V
Figure 3. Input Offset Voltage Production Distribution A3
Figure 4. Input Offset Voltage Production Distribution A4
100
A1
A2
A3
A4
Population
Offset Voltage (PV)
50
0
-100
-50
-25
0
25
50
75
Temperature (qC)
100
125
150
D005
-55
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
5
10
15
20
25
30
35
40
45
50
-50
Common-Mode Rejection Ratio (PV/V)
VIN+ = 0 V
D006
Figure 5. Offset Voltage vs Temperature
Figure 6. Common-Mode Rejection Production Distribution
A1
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
7
INA180-Q1, INA2180-Q1, INA4180-Q1
SLYS017 – APRIL 2018
www.ti.com
Typical Characteristics (continued)
-11
-10
-9
-8
-7
-6
-5
-4
-3
-2
-1
0
1
2
3
4
5
6
7
8
9
10
Population
-32
-29
-26
-23
-20
-17
-14
-11
-8
-5
-2
1
4
7
10
13
16
19
22
25
28
31
Population
at TA = 25°C, VS = 5 V, and VIN+ = 12 V (unless otherwise noted)
D007
Common-Mode Rejection Ratio (PV/V)
D008
Common-Mode Rejection Ratio (PV/V)
Figure 7. Common-Mode Rejection Production Distribution
A2
Figure 8. Common-Mode Rejection Production Distribution
A3
Population
Common-Mode Rejection Ratio (PV/V)
10
A1
A2
A3
A4
8
6
4
2
0
-2
-4
-6
-8
-10
-9
-8
-7
-6
-5
-4
-3
-2
-1
0
1
2
3
4
5
6
7
8
9
10
11
-10
-50
-25
0
25
50
75
Temperature (qC)
100
125
150
D010
D009
Common-Mode Rejection Ratio (PV/V)
Figure 10. Common-Mode Rejection Ratio vs Temperature
D011
Gain Error (%)
Gain Error (%)
D012
Figure 12. Gain Error Production Distribution A2
Figure 11. Gain Error Production Distribution A1
8
-0.11
-0.1
-0.09
-0.08
-0.07
-0.06
-0.05
-0.04
-0.03
-0.02
-0.01
0
0.01
0.02
0.03
0.04
0.05
0.06
0.07
0.08
0.09
0.1
-0.125
-0.115
-0.105
-0.095
-0.085
-0.075
-0.065
-0.055
-0.045
-0.035
-0.025
-0.015
-0.005
0.005
0.015
0.025
0.035
0.045
0.055
0.065
0.075
0.085
Population
Population
Figure 9. Common-Mode Rejection Production Distribution
A4
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
INA180-Q1, INA2180-Q1, INA4180-Q1
www.ti.com
SLYS017 – APRIL 2018
Typical Characteristics (continued)
-0.23
-0.21
-0.19
-0.17
-0.15
-0.13
-0.11
-0.09
-0.07
-0.05
-0.03
-0.01
0.01
0.03
0.05
0.07
0.09
0.11
0.13
0.15
0.17
0.19
Population
-0.12
-0.11
-0.1
-0.09
-0.08
-0.07
-0.06
-0.05
-0.04
-0.03
-0.02
-0.01
0
0.01
0.02
0.03
0.04
0.05
0.06
0.07
0.08
0.09
Population
at TA = 25°C, VS = 5 V, and VIN+ = 12 V (unless otherwise noted)
Gain Error (%)
Gain Error (%)
D013
Figure 13. Gain Error Production Distribution A3
Figure 14. Gain Error Production Distribution A4
50
0.4
A1
A2
A3
A4
0.3
0.2
A1
A2
A3
A4
40
30
0.1
Gain (dB)
Gain Error (%)
D014
0
-0.1
20
10
-0.2
0
-0.3
-0.4
-50
-25
0
25
50
75
Temperature (qC)
100
125
-10
10
150
Figure 15. Gain Error vs Temperature
10k
100k
Frequency (Hz)
1M
10M
D016
140
Common-Mode Rejection Ratio (dB)
Power-Supply Rejection Ratio (dB)
1k
Figure 16. Gain vs Frequency
120
100
80
60
40
20
0
10
100
D015
100
1k
10k
Frequency (Hz)
100k
1M
D017
Figure 17. Power-Supply Rejection Ratio vs Frequency
A1
A2
A3
A4
120
100
80
60
40
20
10
100
1k
10k
Frequency (Hz)
100k
INA2180-Q1
D018
Figure 18. Common-Mode Rejection Ratio vs Frequency
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
1M
9
INA180-Q1, INA2180-Q1, INA4180-Q1
SLYS017 – APRIL 2018
www.ti.com
Typical Characteristics (continued)
at TA = 25°C, VS = 5 V, and VIN+ = 12 V (unless otherwise noted)
VS
120
–40°C
25°C
125°C
100
Input Bias Current (PA)
Output Swing (V)
VS – 1
VS – 2
GND + 2
80
60
40
20
GND + 1
0
GND
0
5
10
15
20 25 30 35 40
Output Current (mA)
45
50
55
-20
-5
60
0
5
10
15
20
Common-Mode Voltage (V)
D019
25
30
D020
Supply voltage = 5 V
Figure 19. Output Voltage Swing vs Output Current
Figure 20. Input Bias Current vs Common-Mode Voltage
120
85
84
100
Input Bias Current (PA)
Input Bias Current (PA)
83
80
60
40
20
82
81
80
79
78
77
0
-20
-5
76
0
5
10
15
20
Common-Mode Voltage (V)
25
75
-50
30
-25
0
D021
25
50
75
Temperature (qC)
100
125
150
D022
Supply voltage = 0 V
Figure 21. Input Bias Current vs Common-Mode Voltage
(Both Inputs, Shutdown)
Figure 22. Input Bias Current vs Temperature
380
210
370
Quiescent Current (PA)
Quiescent Current (PA)
375
205
200
195
365
360
355
350
345
190
-50
-25
0
25
50
75
Temperature (qC)
100
125
D023
Figure 23. Quiescent Current vs Temperature (INA180-Q1)
10
340
-50
150
-25
0
25
50
75
Temperature (qC)
100
125
150
D023
Figure 24. Quiescent Current vs Temperature (INA2180-Q1)
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
INA180-Q1, INA2180-Q1, INA4180-Q1
www.ti.com
SLYS017 – APRIL 2018
Typical Characteristics (continued)
at TA = 25°C, VS = 5 V, and VIN+ = 12 V (unless otherwise noted)
720
400
715
Quiescent Current (PA)
Quiescent Current (PA)
350
710
705
700
695
300
250
200
690
685
-50
-25
0
25
50
75
Temperature (qC)
100
125
150
-5
150
750
1450
700
1350
650
1250
600
550
500
450
400
5
10
15
20
Common-mode Voltage (V)
25
30
D031
Figure 26. Quiescent Current vs Common-Mode Voltage
(INA180-Q1)
Quiescent Current (PA)
Quiescent Current (PA)
Figure 25. Quiescent Current vs Temperature (INA4180-Q1)
1150
1050
950
850
750
650
350
300
-5
0
D038
0
5
10
15
20
Common-Mode Voltage (V)
25
550
-5
30
D031
Figure 27. Quiescent Current vs Common-Mode Voltage
for All Amplifiers (INA2180-Q1)
0
5
10
15
20
Common-Mode Voltage (V)
25
30
D039
Figure 28. Quiescent Current vs Common-Mode Voltage for
All Amplifiers (INA4180-Q1)
80
70
60
Referred-to-Input
Voltage Noise (200 nV/div)
Input-Referred Voltage Noise (nV/—Hz)
100
50
40
30
20
10
10
100
1k
10k
Frequency (Hz)
100k
Time (1 s/div)
1M
D025
D024
Figure 29. Input-Referred Voltage Noise vs Frequency
(A3 Devices)
Figure 30. 0.1-Hz to 10-Hz Voltage Noise (Referred-to-Input)
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
11
INA180-Q1, INA2180-Q1, INA4180-Q1
SLYS017 – APRIL 2018
www.ti.com
Typical Characteristics (continued)
VCM
VOUT
VOUT (100 mV/div)
Input Voltage
40 mV/div
Common-Mode Voltage (5 V/div)
Output Voltage
2 V/div
at TA = 25°C, VS = 5 V, and VIN+ = 12 V (unless otherwise noted)
Time (25 Ps/div)
Time (10 Ps/div)
D027
D026
80-mVPP input step
Figure 31. Step Response
Figure 32. Common-Mode Voltage Transient Response
Voltage (2 V/div)
Noninverting Input
Output
Voltage (2 V/div)
Inverting Input
Output
0V
0V
Time (250 Ps/div)
Time (250 Ps/div)
D028
D029
Figure 33. Inverting Differential Input Overload
Figure 34. Noninverting Differential Input Overload
Supply Voltage
Output Voltage
Voltage (1 V/div)
Voltage (1 V/div)
Supply Voltage
Output Voltage
0V
0V
Time (100 Ps/div)
Time (10 Ps/div)
D032
D030
Figure 35. Start-Up Response
12
Figure 36. Brownout Recovery
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
INA180-Q1, INA2180-Q1, INA4180-Q1
www.ti.com
SLYS017 – APRIL 2018
Typical Characteristics (continued)
at TA = 25°C, VS = 5 V, and VIN+ = 12 V (unless otherwise noted)
200
100
50
140
A1
A2
A3
A4
20
10
5
2
1
0.5
0.2
0.1
10
Ch1 onto Ch2
Ch2 onto Ch1
130
Channel Separation (dB)
Output Impedance (:)
1000
500
120
110
100
90
80
100
1k
10k
100k
Frequency (Hz)
1M
10M
D033
70
100
1k
10k
Frequency (Hz)
100k
1M
D034
Figure 38. Channel Separation vs Frequency (INA2180)
Figure 37. Output Impedance vs Frequency
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
13
INA180-Q1, INA2180-Q1, INA4180-Q1
SLYS017 – APRIL 2018
www.ti.com
8 Detailed Description
8.1 Overview
The INA180-Q1, INA2180-Q1, and INA4180-Q1 (INAx180-Q1) are automotive-grade, 26-V, common-mode,
current-sensing amplifiers used in both low-side and high-side configurations. These specially-designed, currentsensing amplifiers accurately measures voltages developed across current-sensing resistors on common-mode
voltages that far exceed the supply voltage powering the device. Current can be measured on input voltage rails
as high as 26 V, and the devices can be powered from supply voltages as low as 2.7 V.
8.2 Functional Block Diagrams
VS
Single-Channel
TI Device
IN±
±
OUT
+
IN+
GND
Figure 39. INA180-Q1 Functional Block Diagram
VS
Dual-Channel
TI Device
IN±1
±
OUT1
+
IN+1
IN±2
±
OUT2
+
IN+2
GND
Figure 40. INA2180-Q1 Functional Block Diagram
14
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
INA180-Q1, INA2180-Q1, INA4180-Q1
www.ti.com
SLYS017 – APRIL 2018
Functional Block Diagrams (continued)
VS
Quad-Channel
TI Device
IN±1
±
OUT1
+
IN+1
IN±2
±
OUT2
+
IN+2
IN±3
±
OUT3
+
IN+3
IN±4
±
OUT4
+
IN+4
GND
Figure 41. INA4180-Q1 Functional Block Diagram
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
15
INA180-Q1, INA2180-Q1, INA4180-Q1
SLYS017 – APRIL 2018
www.ti.com
8.3 Feature Description
8.3.1 High Bandwidth and Slew Rate
The INAx180-Q1 support small-signal bandwidths as high as 350 kHz, and large-signal slew rates of 2 V/µs. The
ability to detect rapid changes in the sensed current, as well as the ability to quickly slew the output, make the
INAx180-Q1 a good choice for applications that require a quick response to input current changes. One
application that requires high bandwidth and slew rate is low-side motor control, where the ability to follow rapid
changing current in the motor allows for more accurate control over a wider operating range. Another application
that requires higher bandwidth and slew rates is system fault detection, where the INAx180-Q1 are used with an
external comparator and a reference to quickly detect when the sensed current is out of range.
8.3.2 Wide Input Common-Mode Voltage Range
The INAx180-Q1 support input common-mode voltages from –0.2 V to +26 V. Because of the internal topology,
the common-mode range is not restricted by the power-supply voltage (VS) as long as VS stays within the
operational range of 2.7 V to 5.5 V. The ability to operate with common-mode voltages greater or less than VS
allow the INAx180-Q1 to be used in high-side, as well as low-side, current-sensing applications, as shown in
Figure 42.
Bus Supply
±0.2 V to +26 V
Direction of Positive
Current Flow
IN+
High-Side Sensing
Common-mode voltage (VCM)
is bus-voltage dependent.
RSENSE
IN±
LOAD
Direction of Positive
Current Flow
IN+
RSENSE
Low-Side Sensing
Common-mode voltage (VCM)
is always near ground and is
isolated from bus-voltage spikes.
IN±
Figure 42. High-Side and Low-Side Sensing Connections
8.3.3 Precise Low-Side Current Sensing
When used in low-side current sensing applications the offset voltage of the INAx180-Q1 is within ±150 µV. The
low offset performance of the INAx180-Q1 has several benefits. First, the low offset allows the device to be used
in applications that must measure current over a wide dynamic range. In this case, the low offset improves the
accuracy when the sensed currents are on the low end of the measurement range. Another advantage of low
offset is the ability to sense lower voltage drop across the sense resistor accurately, thus allowing a lower-value
shunt resistor. Lower-value shunt resistors reduce power loss in the current sense circuit, and help improve the
power efficiency of the end application.
The gain error of the INAx180-Q1 is specified to be within 1% of the actual value. As the sensed voltage
becomes much larger than the offset voltage, this voltage becomes the dominant source of error in the current
sense measurement.
16
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
INA180-Q1, INA2180-Q1, INA4180-Q1
www.ti.com
SLYS017 – APRIL 2018
Feature Description (continued)
8.3.4 Rail-to-Rail Output Swing
The INAx180-Q1 allow linear current sensing operation with the output close to the supply rail and GND. The
maximum specified output swing to the positive rail is 30 mV, and the maximum specified output swing to GND is
only 5 mV. In order to compare the output swing of the INAx180-Q1 to an equivalent operational amplifier (op
amp), the inputs are overdriven to approximate the open-loop condition specified in op amp data sheets. The
current-sense amplifier is a closed-loop system; therefore, the output swing to GND can be limited by the product
of the offset voltage and amplifier gain.
For devices that have positive offset voltages, the swing to GND is limited by the larger of either the offset
voltage multiplied by the gain or the swing to GND specified in the Electrical Characteristics table.
For example, in an application where the INA180A4-Q1 (gain = 200 V/V) is used for low-side current sensing and
the device has an offset of 40 µV, the product of the device offset and gain results in a value of 8 mV, greater
than the specified negative swing value. Therefore, the swing to GND for this example is 8 mV. If the same
device has an offset of –40 µV, then the calculated zero differential signal is –8 mV. In this case, the offset helps
overdrive the swing in the negative direction, and swing performance is consistent with the value specified in the
Electrical Characteristics table.
The offset voltage is a function of the common-mode voltage as determined by the CMRR specification;
therefore, the offset voltage increases when higher common-mode voltages are present. The increase in offset
voltage limits how low the output voltage can go during a zero-current condition when operating at higher
common-mode voltages. Figure 43 shows the typical limitation of the zero-current output voltage vs commonmode voltage for each gain option.
0.06
A1
A2
A3
A4
Zero Current Output Voltage (V)
0.054
0.048
0.042
0.036
0.03
0.024
0.018
0.012
0.006
0
0
2
4
6
8 10 12 14 16 18 20 22 24 26
Common Mode Voltage (V)
D033
Figure 43. Zero-Current Output Voltage vs Common-Mode Voltage
8.4 Device Functional Modes
8.4.1 Normal Mode
The INAx180-Q1 is in normal operation when the following conditions are met:
• The power supply voltage (VS) is between 2.7 V and 5.5 V.
• The common-mode voltage (VCM) is within the specified range of –0.2 V to +26 V.
• The maximum differential input signal times gain is less than VS minus the output voltage swing to VS.
• The minimum differential input signal times gain is greater than the swing to GND (see the Rail-to-Rail Output
Swing section).
During normal operation, the device produces an output voltage that is the gained-up representation of the
difference voltage from IN+ to IN–.
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
17
INA180-Q1, INA2180-Q1, INA4180-Q1
SLYS017 – APRIL 2018
www.ti.com
Device Functional Modes (continued)
8.4.2 Input Differential Overload
If the differential input voltage (VIN+ – VIN–) times gain exceeds the voltage swing specification, the INAx180-Q1
drive the output as close as possible to the positive supply, and does not provide accurate measurement of the
differential input voltage. If this input overload occurs during normal circuit operation, then reduce the value of the
shunt resistor or use a lower-gain version with the chosen sense resistor to avoid this mode of operation. If a
differential overload occurs in a fault event, then the output of the INAx180-Q1 return to the expected value
approximately 20 µs after the fault condition is removed.
8.4.3 Shutdown Mode
Although the INAx180-Q1 do not have a shutdown pin, the low power consumption of the device allows the
output of a logic gate or transistor switch to power the INAx180-Q1. This gate or switch turns on and off the
INAx180-Q1 power-supply quiescent current.
However, in current shunt monitoring applications, there is also a concern for how much current is drained from
the shunt circuit in shutdown conditions. Evaluating this current drain involves considering the simplified
schematic of the INAx180-Q1 in shutdown mode, as shown in Figure 44.
VS
2.7 V to 5.5 V
RPULL-UP
10 k
Bus Voltage
±0.2 V to +26 V
Shutdown
RSENSE
Load
CBYPASS
0.1 µF
Single-Channel
TI Device
VS
IN±
OUT
±
Output
+
IN+
GND
Figure 44. Basic Circuit to Shut Down the INxA180-Q1
There is typically more than 500 kΩ of impedance (from the combination of 500-kΩ feedback and
input gain set resistors) from each input of the INAx180-Q1 to the OUT pin and to the GND pin. The amount of
current flowing through these pins depends on the voltage at the connection.
Regarding the 500-kΩ path to the output pin, the output stage of a disabled INAx180-Q1 does constitute a good
path to ground. Consequently, this current is directly proportional to a shunt common-mode voltage present
across a 500-kΩ resistor.
As a final note, as long as the shunt common-mode voltage is greater than VS when the device is powered up,
there is an additional and well-matched 55-µA typical current that flows in each of the inputs. If less than VS, the
common-mode input currents are negligible, and the only current effects are the result of the 500-kΩ resistors.
18
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
INA180-Q1, INA2180-Q1, INA4180-Q1
www.ti.com
SLYS017 – APRIL 2018
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The INAx180-Q1 amplify the voltage developed across a current-sensing resistor as current flows through the
resistor to the load or ground.
9.1.1 Basic Connections
Figure 45 shows the basic connections of the INA180-Q1. Connect the input pins (IN+ and IN–) as closely as
possible to the shunt resistor to minimize any resistance in series with the shunt resistor.
Bus Voltage
±0.2 V to +26 V
Power Supply, VS
2.7 V to 5.5 V
CBYPASS
0.1 µF
RSENSE
Load
VS
Single-Channel
TI Device
IN±
Microcontroller
OUT
±
ADC
+
IN+
GND
NOTE: For best measurement accuracy, connect analog-to-digital converter (ADC) reference or microcontroller
ground as closely as possible to the INAx180-Q1 GND pin, and add an RC filter between the output of the INAx180Q1 and the ADC. See Closed-Loop Analysis of Load-Induced Amplifier Stability Issues Using ZOUT for more details.
Figure 45. Basic Connections for the INA180
A power-supply bypass capacitor of at least 0.1 µF is required for proper operation. Applications with noisy or
high-impedance power supplies may require additional decoupling capacitors to reject power-supply noise.
Connect bypass capacitors close to the device pins.
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
19
INA180-Q1, INA2180-Q1, INA4180-Q1
SLYS017 – APRIL 2018
www.ti.com
Application Information (continued)
9.1.2 RSENSE and Device Gain Selection
The accuracy of the INAx180-Q1 is maximized by choosing the current-sense resistor to be as large as possible.
A large sense resistor maximizes the differential input signal for a given amount of current flow and reduces the
error contribution of the offset voltage. However, there are practical limits as to how large the current-sense
resistor can be in a given application. The INAx180-Q1 have a typical input bias currents of 80 µA for each input
when operated at a 12-V common-mode voltage input. When large current-sense resistors are used, these bias
currents cause increased offset error and reduced common-mode rejection. Therefore, using current-sense
resistors larger than a few ohms is generally not recommended for applications that require current-monitoring
accuracy. A second common restriction on the value of the current-sense resistor is the maximum allowable
power dissipation that is budgeted for the resistor. Equation 1 gives the maximum value for the current sense
resistor for a given power dissipation budget:
PDMAX
RSENSE
IMAX2
where:
•
•
PDMAX is the maximum allowable power dissipation in RSENSE.
IMAX is the maximum current that will flow through RSENSE.
(1)
An additional limitation on the size of the current-sense resistor and device gain is due to the power-supply
voltage, VS, and device swing to rail limitations. In order to make sure that the current-sense signal is properly
passed to the output, both positive and negative output swing limitations must be examined. Equation 2 provides
the maximum values of RSENSE and GAIN to keep the device from hitting the positive swing limitation.
IMAX u RSENSE u GAIN VSP
where:
•
•
•
IMAX is the maximum current that will flow through RSENSE.
GAIN is the gain of the current sense-amplifier.
VSP is the positive output swing as specified in the data sheet.
(2)
To avoid positive output swing limitations when selecting the value of RSENSE, there is always a trade-off between
the value of the sense resistor and the gain of the device under consideration. If the sense resistor selected for
the maximum power dissipation is too large, then it is possible to select a lower-gain device in order to avoid
positive swing limitations.
The negative swing limitation places a limit on how small of a sense resistor can be used in a given application.
Equation 3 provides the limit on the minimum size of the sense resistor.
IMIN u RSENSE u GAIN > VSN
where:
•
•
•
20
IMIN is the minimum current that will flow through RSENSE.
GAIN is the gain of the current sense amplifier.
VSN is the negative output swing of the device (see Rail-to-Rail Output Swing).
Submit Documentation Feedback
(3)
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
INA180-Q1, INA2180-Q1, INA4180-Q1
www.ti.com
SLYS017 – APRIL 2018
Application Information (continued)
9.1.3 Signal Filtering
Provided that the INAx180-Q1 output is connected to a high impedance input, the best location to filter is at the
device output using a simple RC network from OUT to GND. Filtering at the output attenuates high-frequency
disturbances in the common-mode voltage, differential input signal, and INAx180-Q1 power-supply voltage. If
filtering at the output is not possible, or filtering of only the differential input signal is required, it is possible to
apply a filter at the input pins of the device. Figure 46 provides an example of how a filter can be used on the
input pins of the device.
Bus Voltage
±0.2 V to +26 V
RSENSE
VS
2.7 V to 5.5 V
Load
f
1
3dB
2S(RF
Single-Channel
TI Device
VS
RF )CF
RF < 10
RINT
IN±
f±3dB
CF
±
OUT VOUT
Bias
+
RF < 10
IN+
RINT
GND
Figure 46. Filter at Input Pins
The addition of external series resistance creates an additional error in the measurement; therefore, the value of
these series resistors must be kept to 10 Ω (or less, if possible) to reduce impact to accuracy. The internal bias
network shown in Figure 46 present at the input pins creates a mismatch in input bias currents when a
differential voltage is applied between the input pins. If additional external series filter resistors are added to the
circuit, the mismatch in bias currents results in a mismatch of voltage drops across the filter resistors. This
mismatch creates a differential error voltage that subtracts from the voltage developed across the shunt resistor.
This error results in a voltage at the device input pins that is different than the voltage developed across the
shunt resistor. Without the additional series resistance, the mismatch in input bias currents has little effect on
device operation. The amount of error these external filter resistors add to the measurement can be calculated
using Equation 5, where the gain error factor is calculated using Equation 4.
The amount of variance in the differential voltage present at the device input relative to the voltage developed at
the shunt resistor is based both on the external series resistance (RF) value as well as internal input resistor RINT,
as shown in Figure 46. The reduction of the shunt voltage reaching the device input pins appears as a gain error
when comparing the output voltage relative to the voltage across the shunt resistor. A factor can be calculated to
determine the amount of gain error that is introduced by the addition of external series resistance. Calculate the
expected deviation from the shunt voltage to what is measured at the device input pins is given using Equation 4:
1250 u RINT
Gain Error Factor
(1250 u RF ) (1250 u RINT ) (RF u RINT )
where:
•
•
RINT is the internal input resistor.
RF is the external series resistance.
(4)
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
21
INA180-Q1, INA2180-Q1, INA4180-Q1
SLYS017 – APRIL 2018
www.ti.com
Application Information (continued)
With the adjustment factor from Equation 4, including the device internal input resistance, this factor varies with
each gain version, as shown in Table 1. Each individual device gain error factor is shown in Table 2.
Table 1. Input Resistance
PRODUCT
GAIN
RINT (kΩ)
INAx180A1-Q1
20
25
INAx180A2-Q1
50
10
INAx180A3-Q1
100
5
INAx180A4-Q1
200
2.5
Table 2. Device Gain Error Factor
PRODUCT
SIMPLIFIED GAIN ERROR FACTOR
INAx180A1-Q1
25000
(21u RF ) 25000
INAx180A2-Q1
10000
(9 u RF ) 10000
INAx180A3-Q1
1000
RF 1000
INAx180A4-Q1
2500
(3 u RF ) 2500
The gain error that can be expected from the addition of the external series resistors can then be calculated
based on Equation 5:
Gain Error (%) = 100 - (100 ´ Gain Error Factor)
(5)
For example, using an INA180A2-Q1 and the corresponding gain error equation from Table 2, a series
resistance
of
10 Ω results in a gain error factor of 0.991. The corresponding gain error is then calculated using Equation 5,
resulting in an additional gain error of approximately 0.89% solely because of the external 10-Ω series resistors.
22
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
INA180-Q1, INA2180-Q1, INA4180-Q1
www.ti.com
SLYS017 – APRIL 2018
9.2 Typical Application
Power Supply, VS
2.7 V to 5.5 V
CBYPASS
0.1 µF
Load
Supply
RSENSE
Load
Single-Channel
TI Device
VS
IN±
OUT
±
VOUT
+
IN+
GND
Figure 47. Low-Side Sensing
9.2.1 Design Requirements
The design requirements for the circuit shown in Figure 47, are listed in Table 3
Table 3. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
Power-supply voltage, VS
5V
Low-side current sensing
VCM = 0 V
RSENSE power loss
< 900 mW
Maximum sense current, IMAX
40 A
Current sensing error
Less than 1.5% at maximum current, TJ = 25°C
Small-signal bandwidth
> 80 kHz
9.2.2 Detailed Design Procedure
The maximum value of the current sense resistor is calculated based on the maximum power loss requirement.
By applying Equation 1, the maximum value of the current-sense resistor is calculated to be 0.563 mΩ. This is
the maximum value for sense resistor RSENSE; therefore, select RSENSE to be 0.5 mΩ because it is the closest
standard resistor value that meets the power-loss requirement.
The next step is to select the appropriate gain and reduce RSENSE, if needed, to keep the output signal swing
within the VS range. Using Equation 2, and given that IMAX = 40 A and RSENSE = 0.5 mΩ, the maximum currentsense gain calculated to avoid the positive swing-to-rail limitations on the output is 248.5. To maximize the output
signal range, the INA180A4-Q1 (gain = 200) device is selected for this application.
To calculate the accuracy at peak current, the two factors that must be determined are the gain error and the
offset error. The gain error of the INAx180-Q1 is specified to be a maximum of 1%. The error due to the offset is
constant, and is specified to be 125 µV (maximum) for the conditions where VCM = 0 V and VS = 5 V. Using
Equation 6, the percentage error contribution of the offset voltage is calculated to be 0.75%, with total offset error
= 150 µV, RSENSE = 0.5 mΩ, and ISENSE = 40 A.
Total Offset Error (V)
Total Offset Error (%) =
u 100%
ISENSE u RSENSE
(6)
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
23
INA180-Q1, INA2180-Q1, INA4180-Q1
SLYS017 – APRIL 2018
www.ti.com
One method of calculating the total error is to add the gain error to the percentage contribution of the offset error.
However, in this case, the gain error and the offset error do not have an influence or correlation to each other. A
more statistically accurate method of calculating the total error is to use the RSS sum of the errors, as shown in
Equation 7:
Total Error (%) = Total Gain Error (%)2 + Total Offset Error (%)2
(7)
After applying Equation 7, the total current sense error at maximum current is calculated to be 1.25%, and that is
less than the design example requirement of 1.5%.
The INA180A4-Q1 (gain = 200) also has a bandwidth of 105 kHz that meets the small-signal bandwidth
requirement of 80 kHz. If higher bandwidth is required, lower-gain devices can be used at the expense of either
reduced output voltage range or an increased value of RSENSE.
9.2.3 Application Curve
Output Voltage (1 V/div)
Figure 48 shows an example output response of a unidirectional configuration. The device output swing is limited
by ground; therefore, the output is biased to this zero output level. The output rises above ground for positive
differential input signals, but cannot fall below ground for negative differential input signals.
0V
Output
Ground
Time (500 µs/div)
Figure 48. Output Response
24
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
INA180-Q1, INA2180-Q1, INA4180-Q1
www.ti.com
SLYS017 – APRIL 2018
10 Power Supply Recommendations
The input circuitry of the INAx180-Q1 accurately measures beyond the power-supply voltage, VS. For example,
VS can be 5 V, whereas the bus supply voltage at IN+ and IN– can be as high as 26 V. However, the output
voltage range of the OUT pin is limited by the voltages on the VS pin. The INAx180-Q1 also withstand the full
differential input signal range up to 26 V at the IN+ and IN– input pins, regardless of whether or not the device
has power applied at the VS pin.
10.1 Common-Mode Transients Greater Than 26 V
With a small amount of additional circuitry, the INAx180-Q1 can be used in circuits subject to transients higher
than 26 V, such as automotive applications. Use only Zener diodes or Zener-type transient absorbers
(sometimes referred to as transzorbs)—any other type of transient absorber has an unacceptable time delay.
Start by adding a pair of resistors as a working impedance for the Zener diode, as shown Figure 49. Keep these
resistors as small as possible; most often, around 10 Ω. Larger values can be used with an effect on gain that is
discussed in the Signal Filtering section. This circuit limits only short-term transients; therefore, many applications
are satisfied with a 10-Ω resistor along with conventional Zener diodes of the lowest acceptable power rating.
This combination uses the least amount of board space. These diodes can be found in packages as small as
SOT-523 or SOD-523.
VS
2.7 V to 5.5 V
Bus Supply
±0.2 V to +26 V
CBYPASS
0.1 µF
RSENSE
Load
Single-Channel
TI Device
VS
IN±
±
RPROTECT
< 10
OUT
Output
+
IN+
GND
Figure 49. Transient Protection Using Dual Zener Diodes
In the event that low-power Zener diodes do not have sufficient transient absorption capability, a higher-power
transzorb must be used. The most package-efficient solution involves using a single transzorb and back-to-back
diodes between the device inputs, as shown in Figure 50. The most space-efficient solutions are dual, seriesconnected diodes in a single SOT-523 or SOD-523 package. In either of the examples shown in Figure 49 and
Figure 50, the total board area required by the INAx180-Q1 with all protective components is less than that of an
SO-8 package, and only slightly greater than that of an MSOP-8 package.
VS
2.7 V to 5.5 V
Bus Supply
±0.2 V to +26 V
CBYPASS
0.1 µF
RSENSE
Load
Single-Channel
TI Device
< 10
VS
IN±
±
Transorb
OUT
Output
+
< 10
IN+
GND
Figure 50. Transient Protection Using a Single Transzorb and Input Clamps
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
25
INA180-Q1, INA2180-Q1, INA4180-Q1
SLYS017 – APRIL 2018
www.ti.com
Common-Mode Transients Greater Than 26 V (continued)
For a reference design example, see Current Shunt Monitor With Transient Robustness Reference Design.
11 Layout
11.1 Layout Guidelines
•
•
•
Connect the input pins to the sensing resistor using a Kelvin or 4-wire connection. This connection technique
makes sure that only the current-sensing resistor impedance is detected between the input pins. Poor routing
of the current-sensing resistor commonly results in additional resistance present between the input pins.
Given the very low ohmic value of the current resistor, any additional high-current carrying impedance can
cause significant measurement errors.
Place the power-supply bypass capacitor as close as possible to the device power supply and ground pins.
The recommended value of this bypass capacitor is 0.1 µF. Additional decoupling capacitance can be added
to compensate for noisy or high-impedance power supplies.
When routing the connections from the current sense resistor to the device, keep the trace lengths as close
as possible in order to minimize any impedance mismatch.
11.2 Layout Examples
Directio n Curr ent Flow
RSHU NT
IN- 4
3 IN+
2 GND
VS 5
1 OUT
Curren t
Sen se
VIA to Gro und
Plan e
CBYPASS
VS: 2.7 V to 5.5 V
Figure 51. Single-Channel Recommended Layout
26
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
INA180-Q1, INA2180-Q1, INA4180-Q1
www.ti.com
SLYS017 – APRIL 2018
Layout Examples (continued)
Bus Voltage:
-0.2V to 26V
VIA to Gro und
Plan e
Directio n o f
Curren t Flo w
RSHU NT2
IN+2 5
4 GND
IN-2 6
3 IN+2
OUT2 7
2 IN-1
VS 8
Curren t Sense
Output 2
RSHU NT1
Directio n o f
Curren t Flo w
1 OUT1
CBYPASS
Curren t Sense
Output 1
VS: 2.7 V to 5.5 V
Loa d2
Loa d1
Figure 52. Dual-Channel Recommended Layout
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
27
INA180-Q1, INA2180-Q1, INA4180-Q1
SLYS017 – APRIL 2018
www.ti.com
Layout Examples (continued)
Loa d2
Loa d3
Curren t Sense
Output 3
Curren t Sense
Output 2
OUT3 8
Directio n o f
Curren t Flo w
RSHU NT3
VIA to
Gro und
Plan e
Bus Voltage3:
-0.2 V to 26 V
7 OUT2
IN-3 9
6 IN-2
IN+3 10
5 IN+2
GND 11
4 VS
IN+4 12
3 IN+1
IN-4 13
2 IN-1
OUT4 14
R SHU NT2
Directio n o f
Curren t Flo w
C BYPASS
Bus Voltage2:
-0.2 V to 26 V
1 OUT1
VIA to
Curren t Sense
Gro und
Output 1
Plan e
Curren t Sense
Output 4
Loa d1
Bus Voltage4:
-0.2 V to 26 V
RSHU NT4
VS: 2.7 V to 5.5 V
Bus Voltage1:
-0.2 V to 26 V
RSHU NT1
Directio n o f
Curren t Flo w
Directio n o f
Curren t Flo w
Loa d4
Loa d1
Figure 53. Quad-Channel Recommended Layout
28
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
INA180-Q1, INA2180-Q1, INA4180-Q1
www.ti.com
SLYS017 – APRIL 2018
12 Device and Documentation Support
12.1 Documentation Support
12.1.1 Related Documentation
For related documentation see the following:
• INA180-181EVM User's Guide
• INA2180-2181EVM User's Guide
• INA4180-4181EVM User's Guide
12.2 Related Links
Table 4 lists quick access links. Categories include technical documents, support and community resources,
tools and software, and quick access to order now.
Table 4. Related Links
PARTS
PRODUCT FOLDER
ORDER NOW
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
INA180-Q1 (preview)
N/A
N/A
N/A
N/A
N/A
INA2180-Q1
Click here
Click here
Click here
Click here
Click here
INA4180-Q1 (preview)
N/A
N/A
N/A
N/A
N/A
12.3 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.4 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.5 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
12.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
29
INA180-Q1, INA2180-Q1, INA4180-Q1
SLYS017 – APRIL 2018
www.ti.com
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
30
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
INA2180-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
19-May-2018
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
INA2180A1QDGKRQ1
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 125
1O16
INA2180A2QDGKRQ1
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 125
1O26
INA2180A3QDGKRQ1
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 125
1O36
INA2180A4QDGKRQ1
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 125
1D26
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
19-May-2018
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF INA2180-Q1 :
• Catalog: INA2180
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
18-May-2018
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
INA2180A1QDGKRQ1
VSSOP
DGK
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
INA2180A2QDGKRQ1
VSSOP
DGK
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
INA2180A3QDGKRQ1
VSSOP
DGK
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
INA2180A4QDGKRQ1
VSSOP
DGK
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
18-May-2018
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
INA2180A1QDGKRQ1
VSSOP
DGK
8
2500
366.0
364.0
50.0
INA2180A2QDGKRQ1
VSSOP
DGK
8
2500
366.0
364.0
50.0
INA2180A3QDGKRQ1
VSSOP
DGK
8
2500
366.0
364.0
50.0
INA2180A4QDGKRQ1
VSSOP
DGK
8
2500
366.0
364.0
50.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
Similar pages