Renesas M37546G2-XXXHP Single-chip 8-bit cmos microcomputer Datasheet

7546 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
DESCRIPTION
•
The 7546 Group is the QzROM version of 7542 Group.
The 7546 Group has the pin-compatibilty with the 7542 Group. As
new functions, the power-on reset, the low voltage detection circuit, and the function set ROM are added.
•
•
•
FEATURES
•
•
•
•
•
•
•
•
•
•
•
Basic machine-language instructions ...................................... 71
The minimum instruction execution time ............................. 0.25 µs
(at 8 MHz oscillation frequency, double-speed mode for the
shortest instruction)
Memory size
ROM ................................ 8K, 16K bytes
RAM ............................... 384, 512 bytes
Programmable I/O ports ........................................................... 25
Interrupts ................................................. 18 sources, 16 vectors
Timers ............................................................................. 8-bit ✕ 2
...................................................................................... 16-bit ✕ 2
Output compare ............................................................ 4-channel
Input capture ................................................................ 2-channel
Serial interface ............ 8-bit ✕ 2 (UART or Clock-synchronized)
A/D converter ............................................... 10-bit ✕ 6 channels
Clock generating circuit ............................................. Built-in type
(low-power dissipation by an on-chip oscillator)
(connected to external ceramic resonator or quartz-crystal
oscillator permitting RC oscillation)
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 1 of 93
•
•
REJ03B0160-0121
Rev.1.21
Nov 15, 2006
Watchdog timer ............................................................ 16-bit ✕ 1
Power-on reset circuit ............................................... Built-in type
Low voltage detection circuit ..................................... Built-in type
Power source voltage
XIN oscillation frequency at ceramic oscillation, in double-speed mode
At 8 MHz .................................................................... 4.5 to 5.5 V
At 6.5 MHz ................................................................. 4.0 to 5.5 V
At 2 MHz .................................................................... 2.4 to 5.5 V
At 1 MHz .................................................................... 2.2 to 5.5 V
XIN oscillation frequency at ceramic oscillation, in high-speed
mode or middle-speed mode
At 8 MHz .................................................................... 4.0 to 5.5 V
At 4 MHz .................................................................... 2.4 to 5.5 V
At 2 MHz .................................................................... 2.2 to 5.5 V
XIN oscillation frequency at RC oscillation in high-speed mode or
middle-speed mode
At 4 MHz .................................................................... 4.0 to 5.5 V
At 2 MHz .................................................................... 2.4 to 5.5 V
At 1 MHz .................................................................... 2.2 to 5.5 V
XIN oscillation frequency at on-chip oscillation ......... 1.8 to 5.5 V
Power dissipation ................................................ 29.5 mW (Typ.)
Operating temperature range ................................... –20 to 85 °C
PIN CONFIGURATION (TOP VIEW)
P06(LED06)/SCLK2
P05(LED05)/TxD2
P04(LED04)/RxD2
P03(LED03)/TXOUT
P02(LED02)/CMP1
P01(LED01)/CMP0
P00(LED00)/CAP0
P37(LED17)/INT0
7546 Group
24 23 22 21 20 19 18 17
P07(LED07)/SRDY2
P10/RXD1/CAP0
P11/TXD1
P12/SCLK1
P13/SRDY1
P14/CNTR0
P20/AN0
P21/AN1
25
16
26
15
14
27
28
29
M37546Gx-XXXGP
M37546GxGP
13
12
30
11
31
10
32
9
2
3
4
5
6
7
8
P22/AN2
P23/AN3
P24/AN4
P25/AN5
VREF
RESET
CNVSS
VCC
1
P34(LED14)
P33(LED13)/INT1
P32(LED12)/CMP3
P31(LED11 )/CMP2
P30(LED10)/CAP1
VSS
XOUT
XIN
Package type: PLQP0032GB-A (32P6U-A)
Fig. 1 Pin configuration (Package type: PLQP0032GB-A)
P12/SCLK1
P13/SRDY1
P14/CNTR0
1
32
P11/TXD1
31
30
P10/RXD1/CAP0
P07(LED07)/SRDY2
P20/AN0
4
29
P06(LED06)/SCLK2
P21/AN1
P22/AN2
5
28
P23/AN3
P24/AN4
7
P05(LED05)/TxD2
P04(LED04)/RxD2
P03(LED03)/TXOUT
P02(LED02)/CMP1
P25/AN5
VREF
9
6
8
M37546Gx-XXXSP
M37546GxSP
2
3
27
26
25
24
22
P01(LED01)/CMP0
P00(LED00)/CAP0
P37(LED17)/INT0
21
P34(LED14)
13
20
14
19
P33(LED13)/INT1
P32(LED12)/CMP3
XOUT
15
18
P31(LED11 )/CMP2
VSS
16
17
P30(LED10)/CAP1
10
RESET
CNVSS
VCC
XIN
11
12
23
Package type: PRDP0032BA-A (32P4B)
Fig. 2 Pin configuration (Package type: PRDP0032BA-A)
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 2 of 93
[N.C.]
P34(LED14)
P37(LED17)/INT0
P00(LED00)/CAP0
P01(LED01)/CMP0
P02(LED02)/CMP1
P03(LED03)/TXOUT
P04(LED04)/RxD2
P05(LED05)/TxD2
7546 Group
27 26 25 24 23 22 21 20 19
P06(LED06)/SCLK2
28
18
[N.C.]
P07(LED07)/SRDY2
29
17
P33(LED13)/INT1
P10/RxD1/CAP0
30
16
P32(LED12)/CMP3
P11/TxD1
31
15
P31(LED11 )/CMP2
P12/SCLK1
32
14
P30(LED10)/CAP1
P13/SRDY1
33
13
Vss
P14/CNTR0
34
12
XOUT
P20/AN0
35
11
XIN
P21/AN1
36
10
[N.C.]
1
2
3
4
5
6
7
8
9
P22/AN2
P23/AN3
P24/AN4
P25/AN5
VREF
RESET
CNVss
Vcc
[N.C.]
M37546Gx-XXXHP
M37546GxHP
Package type: PWQN0036KA-A (36PJW-A)
Fig. 3 Pin configuration (Package type: PWQN0036KA-A)
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 3 of 93
7546 Group
Table 1 Performance overview
Parameter
Function
71
0.25 µs
(Minimum instruction, oscillation frequency 8 MHz: double-speed mode)
Oscillation frequency
8 MHz (max.)
Memory sizes
ROM
8 K to 16 K bytes
RAM
384 to 512 bytes
I/O port
P0, P1, P2, P3
•8-bit ✕ 1, 6-bit ✕ 2, 5-bit ✕ 1
Interrupts
18 sources, 16 vectors
Timer
•8-bit ✕ 2, 16-bit ✕ 2
Output compare
4 channel
Input capture
2 channel
Serial interface
8-bit ✕ 2 (UART or clock synchronous)
A/D converter
10-bit ✕ 6 channel
Watchdog timer
16-bit ✕ 1
Clock generating circuit
Built-in
(external ceramic resonator or quartz-crystal oscillator, RC oscillation available)
(Low consumption current by on-chip oscillator available)
Power source
Double-speed mode At 8MHz oscillation
4.5 to 5.5 V
voltage
At 6.5MHz oscillation 4.0 to 5.5 V
(at ceramic
At 2MHz oscillation
2.4 to 5.5 V
resonance)
At 1MHz oscillation
2.2 to 5.5 V
High-speed mode
At 8MHz oscillation
4.0 to 5.5 V
Middle-speed mode At 4MHz oscillation
2.4 to 5.5 V
At 2MHz oscillation
2.2 to 5.5 V
Power source
High-speed mode
At 4MHz oscillation
4.0 to 5.5 V
voltage
Middle-speed mode At 2MHz oscillation
2.4 to 5.5 V
(at RC oscillation)
At 1MHz oscillation
2.2 to 5.5 V
Power source voltage (at on-chip oscillation)
1.8 to 5.5 V
Power dissipation
29.5 mW (Typ.)
Operating temperature range
-20 to 85 °C
Device structure
CMOS sillicon gate
Package
32-pin plastic molded SDIP/LQFP
36-pin plastic molded WQFN
Number of basic instructions
Instruction execution time
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 4 of 93
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 5 of 93
10
X OUT
Fig. 4 Functional block diagram (Package type: PLQP0032GB-A)
5
VREF
I/O port P3
I/O port P2
4 3 2 1 32 31
Output
Compare
0
PC H
17 16 15 14 13 12
INT0 INT1
Input
Capture
ROM
P2(6)
Reset
Watchdog timer
RAM
8
11
PS
PC L
S
Y
X
A
SI/O2(8)
CPU
VCC
VSS
P3(6)
Reset
Low voltage
detection circuit
A/D
converter
(10)
Reset
Power-on reset
circuit
Clock generating circuit
9
X IN
Clock input Clock output
SI/O1(8)
P1(5)
I/O port P1
30 29 28 27 26
6
RESET
Reset input
CNTR0
Timer X (8)
Timer 1 (8)
I/O port P0
25 24 23 22 21 20 19 18
P0(8)
Timer B (16)
Timer A (16)
Prescaler X (8)
Prescaler 1 (8)
7
CNVSS
Key-on wakeup
FUNCTIONAL BLOCK DIAGRAM (Package type: PLQP0032GB-A) [7546 Group]
7546 Group
FUNCTIONAL BLOCK
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 6 of 93
Fig. 5 Functional block diagram (Package type: PRDP0032BA-A)
10
VREF
I/O port P3
I/O port P2
9 8 7 6 5 4
Output
Compare
0
PC H
22 21 20 19 18 17
INT0 INT1
Input
Capture
ROM
P2(6)
Reset
Watchdog timer
RAM
PS
PC L
S
Y
X
A
SI/O2(8)
CPU
13
16
P3(6)
Reset
Low voltage
detection circuit
A/D
converter
(10)
Reset
Power-on reset
circuit
Clock generating circuit
15
SI/O1(8)
P1(5)
I/O port P1
3 2 1 32 31
11
RESET
14
Reset input
VCC
X IN X OUT
VSS
Clock input Clock output
CNTR0
Timer X (8)
Timer 1 (8)
I/O port P0
30 29 28 27 26 25 24 23
P0(8)
Timer B (16)
Timer A (16)
Prescaler X (8)
Prescaler 1 (8)
12
CNVSS
Key-on wakeup
FUNCTIONAL BLOCK DIAGRAM (Package type: PRDP0032BA-A) [7546 Group]
7546 Group
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 7 of 93
12
11
Fig. 6 Functional block diagram (Package type: PWQN0036KA-A)
5
VREF
I/O port P3
I/O port P2
4 3 2 1 36 35
Output
Compare
0
PC H
21 20 17 16 15 14
INT0 INT1
Input
Capture
ROM
P2(6)
Reset
Watchdog timer
RAM
8
13
PS
PC L
S
Y
X
A
SI/O2(8)
CPU
VCC
VSS
P3(6)
Reset
Low voltage
detection circuit
A/D
converter
(10)
Reset
Power-on reset
circuit
Clock generating circuit
X OUT
X IN
Clock input Clock output
SI/O1(8)
P1(5)
I/O port P1
34 33 32 31 30
6
RESET
Reset input
CNTR0
Timer X (8)
Timer 1 (8)
I/O port P0
29 28 27 26 25 24 23 22
P0(8)
Timer B (16)
Timer A (16)
Prescaler X (8)
Prescaler 1 (8)
7
CNVSS
Key-on wakeup
FUNCTIONAL BLOCK DIAGRAM (Package type: PWQN0036KA-A) [7546 Group]
7546 Group
7546 Group
PIN DESCRIPTION
Table 2 Pin description
Name
Pin
Power
source
Vcc, Vss
Analog
referVREF
ence voltage
CNVss
CNVss
Reset input
RESET
Clock input
XIN
XOUT
Clock output
P00(LED00)/CAP0 I/O port P0
P01(LED01)/CMP0
P02(LED02)/CMP1
P03(LED03)/TXOUT
P04(LED04)/RxD2
P05(LED05)/TxD2
P06(LED06)/SCLK2
P07(LED07)/SRDY2
I/O port P1
P10/RxD1/CAP0
P11/TxD1
P12/SCLK1
P13/SRDY1
P14/CNTR0
P20/AN0–P25/AN5
P30(LED10)/CAP1
P31(LED11)/CMP2
P32(LED12)/CMP3
P33(LED13)/INT1
P34(LED14)
P37(LED17)/INT0
I/O port P2
I/O port P3
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
Function
Apply voltage of 1.8 to 5.5 V to Vcc, and 0 V to Vss.
•Reference voltage input pin for A/D converter.
Function expect a port function
•Chip operating mode control pin, which is always connected to Vss.
•Reset input pin for active “L”
•Input and output pins for main clock generating circuit.
•Connect a ceramic resonator or quartz crystal oscillator between the XIN and XOUT pins.
•For using RC oscillator, short between the XIN and XOUT pins, and connect the capacitor and resistor.
•If an external clock is used, connect the clock source to the XIN pin and leave the XOUT pin open.
•When the on-chip oscillator is selected as the main clock, connect X IN pin to VCC and leave XOUT open.
•8-bit I/O port.
• Capture function pin • Key-input
•I/O direction register allows each pin to be individually pro- • Compare function pin (key-on
wake up
grammed as either input or output.
•CMOS compatible input level
• Timer X function pin interrupt
•CMOS 3-state output structure
• Serial I/O2 function pin input) pin
•Whether a built-in pull-up resistor is to be used or not can be
determined by program.
• High drive capacity for LED drive port can be selected by program.
•5-bit I/O port
•I/O direction register allows each pin to be individually programmed as either input or output.
•CMOS compatible input level
•CMOS 3-state output structure
•CMOS/TTL level can be switched for P10, P12 and P13
•6-bit I/O port having almost the same function as P0
•CMOS compatible input level
•CMOS 3-state output structure
•6-bit I/O port
•I/O direction register allows each pin to be individually programmed as either input or output.
•CMOS compatible input level (CMOS/TTL level can be switched
for P37).
•CMOS 3-state output structure
•Whether a built-in pull-up resistor is to be used or not can be
determined by program.
• High drive capacity for LED drive port can be selected by program.
page 8 of 93
• Serial I/O1 function pin
• Capture function pin
• Serial I/O1 function pin
• Timer X function pin
• Input pins for A/D converter
• Capture function pin
• Compare function pin
• Interrupt input pin
• Interrupt input pin
7546 Group
GROUP EXPANSION
Memory size
ROM size ............................................................. 8 K to 16 K bytes
RAM size .............................................................. 384 to 512 bytes
Renesas plans to expand the 7546 Group as follow:
Memory type
Support for QzROM
Package
PRDP0032BA-A .................................. 32-pin plastic molded SDIP
PLQP0032GB-A .......... 0.8 mm-pitch 32-pin plastic molded LQFP
PWQN0036KA-A ........ 0.5 mm-pitch 36-pin plastic molded WQFN
ROM size
(bytes)
M37546G4
16K
8K
M37546G2
0
384
512
RAM size
(bytes)
**: Under development
Note: Products under development...the development schedule and
specification may be revised without notice.
Fig. 7 Memory expansion plan
Currently supported products are listed below.
Table 3 List of supported products
Product
ROM size (bytes)
ROM size for User ( )
RAM size
(bytes)
(Note)
M37546G2-XXXGP
Package
PLQP0032GB-A
M37546G2-XXXHP
PWQN0036KA-A
8192
M37546G2-XXXSP
384
(8062)
M37546G2GP
PLQP0032GB-A
PWQN0036KA-A
M37546G2SP
PRDP0032BA-A
M37546G4-XXXHP
M37546G4GP
PWQN0036KA-A
16384
(16254)
512
PLQP0032GB-A
PWQN0036KA-A
M37546G4SP
PRDP0032BA-A
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 9 of 93
Shipped after writing
PRDP0032BA-A
M37546G4HP
Note : ROM size includes the function set ROM.
Shipped in blank
PLQP0032GB-A
(Note)
M37546G4-XXXSP
Shipped after writing
PRDP0032BA-A
M37546G2HP
M37546G4-XXXGP
Remarks
Shipped in blank
7546 Group
FUNCTIONAL DESCRIPTION
Stack pointer (S)
The stack pointer is an 8-bit register used during subroutine calls
and interrupts. The stack is used to store the current address data
and processor status when branching to subroutines or interrupt
routines.
The lower eight bits of the stack address are determined by the
contents of the stack pointer. The upper eight bits of the stack address are determined by the Stack Page Selection Bit. If the Stack
Page Selection Bit is “0”, then the RAM in the zero page is used
as the stack area. If the Stack Page Selection Bit is “1”, then RAM
in page 1 is used as the stack area.
The Stack Page Selection Bit is located in the SFR area in the
zero page. Note that the initial value of the Stack Page Selection
Bit varies with each microcomputer type. Also some microcomputer types have no Stack Page Selection Bit and the upper eight
bits of the stack address are fixed. The operations of pushing register contents onto the stack and popping them from the stack are
shown in Fig. 9.
Central Processing Unit (CPU)
The MCU uses the standard 740 family instruction set. Refer to
the table of 740 family addressing modes and machine-language
instructions or the SERIES 740 <SOFTWARE> USER’S MANUAL
for details on each instruction set.
Machine-resident 740 family instructions are as follows:
1. The FST and SLW instructions cannot be used.
2. The MUL and DIV instructions can be used.
3. The WIT instruction can be used.
4. The STP instruction can be used.
Accumulator (A)
The accumulator is an 8-bit register. Data operations such as data
transfer, etc., are executed mainly through the accumulator.
Index register X (X), Index register Y (Y)
Both index register X and index register Y are 8-bit registers. In
the index addressing modes, the value of the OPERAND is added
to the contents of register X or register Y and specifies the real
address.
When the T flag in the processor status register is set to “1”, the
value contained in index register X becomes the address for the
second OPERAND.
b7
Program counter (PC)
The program counter is a 16-bit counter consisting of two 8-bit
registers PC H and PCL. It is used to indicate the address of the
next instruction to be executed.
b0
Accumulator
A
b7
b0
Index Register X
X
b7
b0
Index Register Y
Y
b7
b0
Stack Pointer
S
b15
b7
PCH
b0
Program Counter
PCL
b7
b0
N V T B D I Z C Processor Status Register (PS)
Carry Flag
Zero Flag
Interrupt Disable Flag
Decimal Mode Flag
Break Flag
Index X Mode Flag
Overflow Flag
Negative Flag
Fig. 8 740 Family CPU register structure
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 10 of 93
7546 Group
On-going Routine
Interrupt request
(Note)
M (S)
Execute JSR
M (S)
Store Return Address
on Stack
(S)
(PC H)
(S)
(S – 1)
M (S)
(PCL)
(S)
(S – 1)
M (S)
Subroutine
Restore Return
Address
(S + 1)
(PCL)
M (S)
(S)
(S + 1)
(PCH)
M (S)
(S – 1)
(PC L)
(S)
(S – 1)
M (S)
(PS)
(S)
(S – 1)
Interrupt
Service Routine
Execute RTS
(S)
(PC H)
Execute RTI
Note : The condition to enable the interrupt
(S)
(S + 1)
(PS)
M (S)
(S)
(S + 1)
(PC L)
M (S)
(S)
(S + 1)
(PC H)
M (S)
Store Return Address
on Stack
Store Contents of Processor
Status Register on Stack
I Flag “0” to “1”
Fetch the Jump Vector
Restore Contents of
Processor Status Register
Restore Return
Address
Interrupt enable bit is “1”
Interrupt disable flag is “0”
Fig. 9 Register push and pop at interrupt generation and subroutine call
Table 4 Push and pop instructions of accumulator or processor status register
Push instruction to stack
PHA
PHP
Accumulator
Processor status register
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 11 of 93
Pop instruction from stack
PLA
PLP
7546 Group
Processor status register (PS)
The processor status register is an 8-bit register consisting of
flags which indicate the status of the processor after an arithmetic
operation. Branch operations can be performed by testing the
Carry (C) flag, Zero (Z) flag, Overflow (V) flag, or the Negative (N)
flag. In decimal mode, the Z, V, N flags are not valid.
After reset, the Interrupt disable (I) flag is set to “1”, but all other
flags are undefined. Since the Index X mode (T) and Decimal
mode (D) flags directly affect arithmetic operations, they should
be initialized in the beginning of a program.
(1) Carry flag (C)
The C flag contains a carry or borrow generated by the arithmetic
logic unit (ALU) immediately after an arithmetic operation. It can
also be changed by a shift or rotate instruction.
(2) Zero flag (Z)
The Z flag is set if the result of an immediate arithmetic operation
or a data transfer is “0”, and cleared if the result is anything other
than “0”.
(3) Interrupt disable flag (I)
The I flag disables all interrupts except for the interrupt generated
by the BRK instruction. Interrupts are disabled when the I flag is
“1”.
When an interrupt occurs, this flag is automatically set to “1” to
prevent other interrupts from interfering until the current interrupt
is serviced.
(4) Decimal mode flag (D)
The D flag determines whether additions and subtractions are executed in binary or decimal. Binary arithmetic is executed when
this flag is “0”; decimal arithmetic is executed when it is “1”.
Decimal correction is automatic in decimal mode. Only the ADC
and SBC instructions can be used for decimal arithmetic.
(5) Break flag (B)
The B flag is used to indicate that the current interrupt was generated by the BRK instruction. The BRK flag in the processor status
register is always “0”. When the BRK instruction is used to generate an interrupt, the processor status register is pushed onto the
stack with the break flag set to “1”. The saved processor status is
the only place where the break flag is ever set.
(6) Index X mode flag (T)
When the T flag is “0”, arithmetic operations are performed between accumulator and memory, e.g. the results of an operation
between two memory locations is stored in the accumulator. When
the T flag is “1”, direct arithmetic operations and direct data transfers are enabled between memory locations, i.e. between memory
and memory, memory and I/O, and I/O and I/O. In this case, the
result of an arithmetic operation performed on data in memory location 1 and memory location 2 is stored in memory location 1.
The address of memory location 1 is specified by index register X,
and the address of memory location 2 is specified by normal addressing modes.
(7) Overflow flag (V)
The V flag is used during the addition or subtraction of one byte
of signed data. It is set if the result exceeds +127 to -128. When
the BIT instruction is executed, bit 6 of the memory location operated on by the BIT instruction is stored in the overflow flag.
(8) Negative flag (N)
The N flag is set if the result of an arithmetic operation or data
transfer is negative. When the BIT instruction is executed, bit 7 of
the memory location operated on by the BIT instruction is stored in
the negative flag.
Table 5 Set and clear instructions of each bit of processor status register
Set instruction
Clear instruction
C flag
SEC
CLC
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
Z flag
–
–
page 12 of 93
I flag
SEI
CLI
D flag
SED
CLD
B flag
–
–
T flag
SET
CLT
V flag
–
CLV
N flag
–
–
7546 Group
Memory
Special function register (SFR) area
The SFR area in the zero page contains control registers such as
I/O ports and timers.
RAM
RAM is used for data storage and for a stack area of subroutine
calls and interrupts.
ROM
The first 128 bytes and the last 2 bytes of ROM are reserved for
device testing and the rest is a user area for storing programs.
Interrupt vector area
The interrupt vector area contains reset and interrupt vectors.
Zero page
The 256 bytes from addresses 000016 to 00FF 16 are called the
zero page area. The internal RAM and the special function registers (SFR) are allocated to this area.
The zero page addressing mode can be used to specify memory
and register addresses in the zero page area. Access to this area
with only 2 bytes is possible in the zero page addressing mode.
ROM Code Protect Address (address FFDB16)
Address FFDB16, which is the reserved ROM area of QzROM, is
the ROM code protect address. “0016” is written into this address
when selecting the protect bit write by using a serial programmer
or selecting protect enabled for writing shipment by Renesas
Technology corp.. When “0016” is set to the ROM code protect address, the protect function is enabled, so that reading or writing
from/to QzROM is disabled by a serial programmer.
As for the QzROM product in blank, the ROM code is protected by
selecting the protect bit write at ROM writing with a serial programmer.
As for the QzROM product shipped after writing, “0016” (protect
enabled) or “FF16” (protect disabled) is written into the ROM code
protect address when Renesas Technology corp. performs writing.
The writing of “0016” or “FF16” can be selected as the ROM option
setup (referred to as “Mask option setup” in MM) when ordering.
■ Notes
Because the contents of RAM are indefinite at reset, set initial values before using.
Special page
The 256 bytes from addresses FF0016 to FFFF 16 are called the
special page area. The special page addressing mode can be
used to specify memory addresses in the special page area. Access to this area with only 2 bytes is possible in the special page
addressing mode.
000016
SFR area
Zero page
004016
RAM area
RAM capacity
(bytes)
384
512
address
XXXX16
RAM
010016
01BF16
023F16
XXXX16
Function set ROM consists of the followings:
- Function set ROM data to set peripheral
functions to be active immediately after system
is released from reset,
- ROM code protect to disable the reading of
the built-in PROM area by serial programmer,
- Renesas shipment test area where random
data are written in when shipment test is
performed by Renesas.
Reserved area
044016
Not used
YYYY16
Address
FFD416 Renesas shipment test area
FFD516 Renesas shipment test area
FFD616 Renesas shipment test area
Reserved ROM area
(128 bytes)
ZZZZ16
FFD716 Renesas shipment test area
FFD816 Function set ROM data 0
FFD916 Function set ROM data 1
Function set ROM data 2
FFDA16
FFDB16
ROM code protect
ROM
FF0016
FFD4 16
ROM area
ROM capacity
(bytes)
address
YYYY16
address
ZZZZ16
8192
16384
E00016
C00016
E08016
C08016
Fig. 10 Memory map diagram
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 13 of 93
FFDC16
FFFE16
FFFF16
Function set ROM function area
Interrupt vector area
Reserved ROM area
Special page
7546 Group
[CPU mode register] CPUM
The CPU mode register contains the stack page selection bit, etc..
This register is allocated at address 003B16.
Some function of the CPU mode register can be controlled by the
function set ROM data 2.
b7
Switching method of CPU mode register
Switch the CPU mode register (CPUM) at the head of program after releasing Reset in the following method.
b0
CPU mode register (Note 1)
(CPUM: address 003B16, initial value: 8016)
Control by Function set ROM data 2
(FSROM2: address FFDA16) (Note 2)
This cannot be controlled by FSROM2.
Processor mode bits
b1 b0
0 0 Single-chip mode
0 1 Not available
1 0 Not available
1 1 Not available
Stack page selection bit
0 : 0 page
1 : 1 page
This cannot be controlled by FSROM2.
On-chip oscillator oscillation control bit (Note 3)
0 : On-chip oscillator oscillation enabled
1 : On-chip oscillator oscillation stop
This bit function can be set by setting bit 4 of FSROM2. (Note 3)
Bit 4 of FSROM2 = 0: Bit 3 of CPUM is fixed to “0”.
Bit 4 of FSROM2 = 1: Bit 3 of CPUM is “0” or “1”.
XIN oscillation control bit
0 : Ceramic or RC oscillation enabled
1 : Ceramic or RC oscillation stop
This cannot be controlled by FSROM2.
This bit function can be set by setting bit 5 of FSROM2. (Note 4)
Oscillation mode selection bit (Note 1, Note 4)
Bit 5 of FSROM2 = 0: Bit 5 of CPUM is fixed to “0”.
0 : Ceramic oscillation
Bit 5 of FSROM2 = 1: Bit 5 of CPUM is “0” or “1”.
1 : RC oscillation
Clock division ratio selection bits
This cannot be controlled by FSROM2.
b7 b6
0 0 : f(φ) = f(XIN)/2 (High-speed mode)
0 1 : f(φ) = f(XIN)/8 (Middle-speed mode)
1 0 : applied from on-chip oscillator
1 1 : f(φ) = f(XIN)/1 (Double-speed mode)(Note 5)
Note 1: When the setting by the function set ROM data 2 (FSROM2) is performed, the initial value of CPUM is changed
after releasing reset since bit 5 of CPUM is fixed.
2: The setting values of FSROM2 become valid by setting “0” to bit 0 of function set ROM data 0 (FSROM0).
The setting values of FSROM2 are invalid by setting “1” to this bit.
(In order that FSROM2 is invalid, write to CPUM after releasing reset.)
3: When bit 4 of FSROM2 is set to “0”, the operation of on-chip oscillator cannot be stopped.
Since the on-chip oscillator is not stopped also in the stop mode, the dissipation current in the stop mode is increased.
4: The setting value of bit 5 of CPUM can be fixed after releasing reset by setting value of bit 5 of FSROM2.
Also, when the setting of FSROM2 is invalid, this bit can be rewritten only once after releasing reset.
After rewriting it is disable to write any data to this bit.
This bit is initialized by reset, and then, rewriting it is enabled.
5: This setting can be used only at ceramic oscillation. Do not use this at RC oscillation.
Fig. 11 Structure of CPU mode register
After releasing reset
Start with an on-chip oscillator
Switch the oscillation mode
selection bit (bit 5 of CPUM)
An initial value is set as a ceramic oscillation mode.
When it is switched to an RC oscillation, its oscillation starts.
Wait by on-chip oscillator operation
until establishment of oscillator clock
When using a ceramic oscillation, wait until establlishment of
oscillation from oscillation starts.
When using an RC oscillation, wait time is not required
basically (time to execute the instruction to switch from an
on-chip oscillator meets the requirement).
Switch the clock division ratio
selection bits (bits 6 and 7 of CPUM)
Select 1/1, 1/2, 1/8 or on-chip oscillator.
Main routine
Note: After system is released from reset, an on-chip oscillator turns active automatically and system operation
is started.
Fig. 12 Switching method of CPU mode register
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 14 of 93
7546 Group
Port P0 (P0)
002016
Capture mode register (CAPM)
000116
Port P0 direction register (P0D)
002116
Compare output mode register (CMOM)
000216
Port P1 (P1)
002216
Capture/compare status register (CCSR)
000316
Port P1 direction register (P1D)
002316
Compare interrupt source set register (CISR)
000416
Port P2 (P2)
002416
Timer A (low-order) (TAL)
000516
Port P2 direction register (P2D)
002516
Timer A (high-order) (TAH)
000616
Port P3 (P3)
002616
Timer B (low-order) (TBL)
000716
Port P3 direction register (P3D)
002716
Timer B (high-order) (TBH)
000816
Reserved
002816
Prescaler 1 (PRE1)
Timer 1 (T1)
000016
000916
Reserved
002916
000A16
Interrupt source set register (INTSET)
002A16
Timer count source set register (TCSS)
000B16
Interrupt source discrimination register (INTDIS)
002B16
Timer X mode register (TXM)
000C16
Capture register 0 (low-order) (CAP0L)
002C16
Prescaler X (PREX)
000D16
Capture register 0 (high-order) (CAP0H)
002D16
Timer X (TX)
000E16
Capture register 1 (low-order) (CAP1L)
002E16
Transmit 2 / Receive 2 buffer register (TB2/RB2)
000F16
Capture register 1 (high-order) (CAP1H)
002F16
Serial I/O2 status register (SIO2STS)
001016
Compare register (low-order) (CMPL)
003016
Serial I/O2 control register (SIO2CON)
001116
Compare register (high-order) (CMPH)
003116
UART2 control register (UART2CON)
001216
Capture/compare register R/W pointer (CCRP)
003216
Baud rate generator 2 (BRG2)
001316
Capture software trigger register (CSTR)
003316
Reserved
001416
Compare register re-load register (CMPR)
003416
A/D control register (ADCON)
001516
Port P0P3 drive capacity control register (DCCR)
003516
A/D conversion register (low-order) (ADL)
001616
Pull-up control register (PULL)
003616
A/D conversion register (high-order) (ADH)
001716
Port P1P3 control register (P1P3C)
003716
On-chip oscillation division ratio selection register (RODR)
001816
Transmit 1 /Receive 1 buffer register (TB1/RB1)
003816
MISRG
001916
Serial I/O1 status register (SIO1STS)
003916
Watchdog timer control register (WDTCON)
001A16
Serial I/O1 control register (SIO1CON)
003A16
Interrupt edge selection register (INTEDGE)
001B16
UART1 control register (UART1CON)
003B16
CPU mode register (CPUM)
001C16
Baud rate generator 1 (BRG1)
003C16
Interrupt request register 1 (IREQ1)
001D16
Timer A, B mode register (TABM)
003D16
Interrupt request register 2 (IREQ2)
001E16
Capture/compare port register (CCPR)
003E16
Interrupt control register 1 (ICON1)
001F16
Timer source selection register (TMSR)
003F16
Interrupt control register 2 (ICON2)
Notes 1: Do not access to the SFR area including nothing.
Fig. 13 Memory map of special function register (SFR)
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 15 of 93
7546 Group
I/O Ports
[Direction registers] PiD
The I/O ports have direction registers which determine the input/
output direction of each pin. Each bit in a direction register corresponds to one pin, and each pin can be set to be input or output.
When “1” is set to the bit corresponding to a pin, this pin becomes
an output port. When “0” is set to the bit, the pin becomes an input port.
When data is read from a pin set to output, not the value of the pin
itself but the value of port latch is read. Pins set to input are floating, and permit reading pin values.
If a pin set to input is written to, only the port latch is written to and
the pin remains floating.
• Set bits 6 and 7 of port P2 direction register to “1”.
• Set bits 5 and 6 of port P3 direction register to “1”.
[Port P0P3 drive capacity control register] DCCR
By setting the Port P0P3 drive capacity control register (address
001516), the drive capacity of the N-channel output transistor for
the port P0 and port P3 can be selected.
b7
b0
Port P0P3 drive capacity control register
(DCCR: address 001516, initial value: 0016)
Port P00 drive capacity bit
Ports P01, P02 drive capacity bit
Ports P03–P07 drive capacity bit
Port P30 drive capacity bit
Ports P31, P32 drive capacity bit
Port P33 drive capacity bit
Ports P34 drive capacity bit
Ports P37 drive capacity bit
0 : Low
1 : High
Note: Number of LED drive port (drive capacity is HIGH) is 8-port.
Fig. 14 Structure of port P0P3 drive capacity control register
b7
b0
Pull-up control register
(PULL: address 001616, initial value: 0016)
[Pull-up control register] PULL
By setting the pull-up control register (address 001616), ports P0
and P3 can exert pull-up control by program. However, pins set to
output are disconnected from this control and cannot exert pull-up
control.
P00 pull-up control bit
P01, P02 pull-up control bit
P03–P07 pull-up control bit
P30 pull-up control bit
P31, P32 pull-up control bit
P33 pull-up control bit
[Port P1P3 control register] P1P3C
By setting the port P1P3 control register (address 0017 16), a
CMOS input level or a TTL input level can be selected for ports
P10, P12, P13, and P37 by program.
P34 pull-up control bit
0 : Pull-up Off
1 : Pull-up On
P37 pull-up control bit
Note : Pins set to output ports are disconnected from pull-up control.
Fig. 15 Structure of pull-up control register
b7
b0
Port P1P3 control register
(P1P3C: address 001716, initial value: 0016)
P37/INT0 input level selection bit
0 : CMOS level
1 : TTL level
Set “0” to this bit certainly.
P10,P12,P13 input level selection bit
0 : CMOS level
1 : TTL level
Not used
Fig. 16 Structure of port P1P3 control register
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 16 of 93
7546 Group
Table 6 I/O port function table
Pin
P00(LED00)/CAP0
Name
I/O format
P03(LED03)/TXOUT
P04(LED04)/RxD2
P05(LED05)/TxD2
P06(LED06)/SCLK2
P07(LED07)/SRDY2
I/O port P1
P11/TxD1
P12/SCLK1
P13/SRDY1
P14/CNTR0
P20/AN0–P25/AN5
P30(LED10)/CAP1
SFRs related each pin
I/O port P0 •CMOS compatible
• Capture function input
input level (Note 1)
• Key input interrupt
•CMOS 3-state output
P01(LED01)/CMP0
P02(LED02)/CMP1
P10/RxD1/CAP0
Non-port function
I/O port P2
I/O port P3
Capture/Compare port register
Interrupt edge selection register
Pull-up control register
Port P0P3 drive capacity control register
• Compare function output
Capture/Compare port register
• Key input interrupt
Pull-up control register
Port P0P3 drive capacity control register
• Timer X function output
Timer X mode register
• Key input interrupt
Pull-up control register
Port P0P3 drive capacity control register
• Serial I/O2 function input/output Serial I/O2 control register
• Key input interrupt
Interrupt edge selection register
Pull-up control register
Port P0P3 drive capacity control register
Serial I/O2 control register
Pull-up control register
Port P0P3 drive capacity control register
Serial I/O2 control register
Interrupt edge selection register
Pull-up control register
Port P0P3 drive capacity control register
Serial I/O2 control register
Pull-up control register
Port P0P3 drive capacity control register
• Serial I/O1 function input
Serial I/O1 control register
• Capture function input
Capture/Compare port register
Port P1P3 control register
• Serial I/O1 function input/output Serial I/O1 control register
Serial I/O1 control register
Port P1P3 control register
Serial I/O1 control register
Port P1P3 control register
• Timer X function input/output
Timer X mode register
• External interrupt input
• A/D conversion input
A/D control register
• Capture function input
Capture/Compare port register
P31(LED11)/CMP2
P32(LED12)/CMP3
• Compare function output
P33(LED13)/INT1
• External interrupt input
P34(LED14)
P37(LED17)/INT0
• External interrupt input
Notes 1: Ports P10, P12, P13, P37 are CMOS/TTL level.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 17 of 93
Pull-up control register
Port P0P3 drive capacity control register
Capture/Compare port register
Pull-up control register
Port P0P3 drive capacity control register
Interrupt edge selection register
Pull-up control register
Port P0P3 drive capacity control register
Pull-up control register
Port P0P3 drive capacity control register
Interrupt edge selection register
Pull-up control register
Port P0P3 drive capacity control register
Port P1P3 control register
Diagram
No.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
7546 Group
(1) Port P00
(2) Ports P01, P02
Pull-up control
Compare output control
Direction
register
Direction
register
Port latch
Data bus
Data bus
Port latch
Drive capacity
control
Capture 0 input
Capture 0 input control
To key input interrupt
generating circuit
(3) Port P03
P03/TXOUT output valid
Drive capacity
control
Compare output
To key input interrupt
generating circuit
P00 key-on wakeup
selection bit
(4) Port P04
Pull-up control
Serial I/O2 enable bit
Receive enable bit
Direction
register
Direction
register
Data bus
Port latch
Pull-up control
Port latch
Data bus
Drive capacity
control
Drive capacity
control
Timer output
Serial I/O2 input
To key input interrupt
generating circuit
To key input interrupt
generating circuit
(5) Port P05
P04 key-on wakeup
selection bit
(6) Port P06
Pull-up control
Serial I/O2 enable bit
Transmit enable bit
Direction
register
Data bus
Pull-up control
Serial I/O2 synchronous
clock selection bit
Serial I/O2 enable bit
Serial I/O2 mode selection bit
Serial I/O2 enable bit
Direction
register
Port latch
Drive capacity
control
Data bus
Pull-up control
Port latch
Drive capacity
control
Serial I/O2 output
To key input interrupt
generating circuit
Serial I/O2 clock output
Serial I/O2 clock input
To key input interrupt
generating circuit
(7) Port P07
Serial I/O2 mode selection bit
Serial I/O2 enable bit
SRDY2 output enable bit
Direction
register
Data bus
Pull-up control
Port latch
Drive capacity
control
Serial I/O2 ready output
To key input interrupt
generating circuit
Fig. 17 Block diagram of ports (1)
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 18 of 93
P06 key-on wakeup
selection bit
7546 Group
(8) Port P10
(9) Port P11
Serial I/O1 enable bit
Receive enable bit
P11/TxD1 P-channel output disable bit
Serial I/O1 enable bit
Transmit enable bit
Direction
register
Data bus
Direction
register
Port latch
P10, P12, P13
input level
selection bit
Data bus
Port latch
*
Serial I/O1 input
Capture 0 input control
Capture 0 input
Serial I/O1 output
(11) Port P13
(10) Port P12
Serial I/O1 synchronous
clock selection bit
Serial I/O1 enable bit
Serial I/O1 mode selection bit
Serial I/O1 enable bit
SRDY1 output enable bit
Serial I/O1 mode selection bit
Serial I/O1 enable bit
Direction
register
Direction
register
Port latch
Data bus
Data bus
P10, P12, P13
input level
selection bit
Port latch
P10, P12, P13
input level
selection bit
Serial I/O1 ready output
*
Serial I/O1 clock output
Serial I/O1 clock input
*
(13) Ports P20–P25
(12) Port P14
Pulse output mode
Direction
register
Data bus
Direction
register
Port latch
Data bus
Timer output
CNTR0 interrupt input
*
P10, P12, P13, and P37 input level are switched to the CMOS/TTL level by the port P1P3 control register.
When the TTL level is selected, there is no hysteresis characteristics.
Fig. 18 Block diagram of ports (2)
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 19 of 93
Port latch
A/D converter input
Analog input pin
selection bit
7546 Group
(15) Ports P31, P32
(14) Port P30
Pull-up control
Compare output control
Direction
register
Direction
register
Data bus
Data bus
Port latch
Port latch
Drive capacity
control
Drive capacity
control
Capture 1 input
Capture 1 input control
Compare output
(16) Port P33
(17) Ports P34
Pull-up control
Pull-up control
Direction
register
Data bus
Direction
register
Data bus
Port latch
Port latch
Drive capacity
control
INT1 input control
INT1 input
(18) Port P37
Pull-up control
Direction
register
Data bus
Port latch
P3 input level
selection bit
Drive capacity
control
*
INT0 input
*
Pull-up control
P10, P12, P13, and P37 input level are switched to the CMOS/TTL level by the port P1P3 control register.
When the TTL level is selected, there is no hysteresis characteristics.
Fig. 19 Block diagram of ports (3)
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 20 of 93
Drive capacity
control
7546 Group
Termination of unused pins
• Termination of common pins
I/O ports:
Select an input port or an output port and follow
each processing method.
Output ports: Open.
Input ports: If the input level become unstable, through current
flow to an input circuit, and the power supply current
may increase.
Especially, when expecting low consumption current
(at STP or WIT instruction execution etc.), pull-up or
pull-down input ports to prevent through current
(built-in resistor can be used).
We recommend processing unused pins through a
resistor which can secure IOH(avg) or IOL(avg).
Because, when an I/O port or a pin which have an
output function is selected as an input port, it may
operate as an output port by incorrect operation etc.
Table 7 Termination of unused pins
Termination 1
Termination 2
(recommend)
I/O port
When selecting CAP function,
P00/CAP0
perform termination of input port.
When selecting CMP0 function,
P01/CMP0
perform termination of output port.
When selecting CMP1 function,
P02/CMP1
perform termination of output port.
When selecting TXOUT function,
P03/TXOUT
perform termination of output port.
When selecting RxD2 function,
P04/RxD2
perform termination of input port.
When selecting TxD2 function,
P05/TxD2
perform termination of output port.
P06/SCLK2
When selecting external clock input,
perform termination of output port.
P07/SRDY2
When selecting SRDY2 function,
perform termination of output port.
P10/RxD1/CAP0
When selecting RxD1 function,
perform termination of input port.
P11/TxD1
When selecting TxD1 function,
perform termination of output port.
P12/SCLK1
When selecting external clock input,
perform termination of input port.
P13/SRDY1
When selecting SRDY1 function,
perform termination of output port.
P14/CNTR0
When selecting CNTR input function,
perform termination of input port.
P20/AN0–P25/AN5
When selecting AN function,
perform termination of input port.
P30/CAP1
When selecting CAP function,
perform termination of input port.
P31/CMP2
When selecting CMP2 function,
perform termination of output port.
P32/CMP3
When selecting CMP3 function,
perform termination of output port.
P33/INT1
When selecting INT function,
perform termination of input port.
P34
Pin
P37/INT0
VREF
When selecting INT function,
perform termination of input port.
Connect to Vss.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 21 of 93
Termination 3
Termination 4
-
When selecting key-on
wakeup function, perform
termination of input port.
When selecting internal clock output,
perform termination of output port.
When selecting CAP function, perform termination of input port.
-
-
When selecting internal clock output,
perform termination of output port.
-
-
When selecting CNTR output function,
perform termination of output port.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
7546 Group
Interrupts
Interrupts occur by 18 different sources : 6 external sources, 11 internal sources and 1 software source.
Interrupt control
All interrupts except the BRK instruction interrupt have an interrupt
request bit and an interrupt enable bit, and they are controlled by
the interrupt disable flag. When the interrupt enable bit and the interrupt request bit are set to “1” and the interrupt disable flag is set
to “0”, an interrupt is accepted.
The interrupt request bit can be cleared by program but not be set.
The interrupt enable bit can be set and cleared by program.
The reset and BRK instruction interrupt can never be disabled with
any flag or bit. All interrupts except these are disabled when the
interrupt disable flag is set.
When several interrupts occur at the same time, the interrupts are
received according to priority.
Interrupt operation
Upon acceptance of an interrupt the following operations are automatically performed:
1. The processing being executed is stopped.
2. The contents of the program counter and processor status register are automatically pushed onto the stack.
3. The interrupt disable flag is set and the corresponding interrupt
request bit is cleared.
4. Concurrently with the push operation, the interrupt destination
address is read from the vector table into the program counter.
[Interrupt source set register] INTSET
When two interrupt sources are assigned to the same interrupt
vector, the valid/invalid of each interrupt is set by this register.
When both two interrupt sources are set to be valid, which interrupt request occurs is confirmed by the next interrupt source
discrimination register.
[Interrupt source discrimination register] INTDIS
When two interrupt sources are assigned to the same interrupt
vector, which interrupt source occurs is confirmed by this register.
If an interrupt request of a key-on wakeup, UART1 bus collision
detection, A/D conversion or timer 1 occurs, an interrupt discrimination bit is set to “1” regardless of valid/invalid state by the
interrupt source set register.
However, when the interrupt valid bit of an interrupt source set
register is “0” (invalid), the interrupt request bit of an interrupt control register is not set to “1.”
Moreover, since an interrupt discrimination bit is not automatically
cleared to “0” by interrupt, please clear it by program.
An interrupt discrimination bit can be cleared to “0” by program but
not be set to “1.”
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 22 of 93
[Interrupt edge selection register] INTEDGE
The valid edge of external interrupt INT0 and INT1 can be selected
by the interrupt edge selection bit, respectively.
Set bit 2 of interrupt edge selection register to “1”.
■ Notes on use
(1) When setting the followings, the interrupt request bit may be
set to “1”.
•When switching external interrupt active edge
Related register:
Interrupt edge selection register (address 003A16)
Timer X mode register (address 002B16)
Capture mode register (address 002016)
When not requiring the interrupt occurrence synchronized with
these setting, take the following sequence.
➀ Set the corresponding interrupt enable bit to “0” (disabled).
➁ Set the interrupt edge select bit (active edge switch bit, trigger
mode bit).
➂ Set the corresponding interrupt request bit to “0” after 1 or more
instructions have been executed.
➃ Set the corresponding interrupt enable bit to “1” (enabled).
(2) Use a LDM instruction to clear an interrupt discrimination bit.
LDM #$0n, $0B
Set the following values to “n”
“0”: an interrupt discrimination bit to clear
“1”: other interrupt discrimination bits
Ex.) When a key-on wakeup interrupt discrimination bit is
cleared;
LDM #00001110B and $0B.
7546 Group
Table 8 Interrupt vector address and priority
Interrupt source Priority
Vector addresses (Note 1)
High-order
Low-order
Reset (Note 2)
Serial I/O1 receive
Serial I/O1 transmit
1
2
3
FFFD16
FFFB16
FFF916
FFFC16
FFFA16
FFF816
Serial I/O2 receive
Serial I/O2 transmit
4
5
FFF716
FFF516
FFF616
FFF416
INT0
6
FFF316
FFF216
INT1
7
FFF116
FFF016
Key-on wake-up/
UART1 bus
collision detection
8
FFEF16
FFEE16
(Note 3)
CNTR0
9
FFED16
FFEC16
Capture 0
10
FFEB16
FFEA16
Capture 1
11
FFE916
FFE816
Compare
Timer X
Timer A
Timer B
A/D conversion/
Timer 1
(Note 4)
BRK instruction
12
13
14
15
16
FFE716
FFE516
FFE316
FFE116
FFDF16
FFE616
FFE416
FFE216
FFE016
FFDE16
17
FFDD16
FFDC16
Interrupt request generating conditions
At reset input
At completion of serial I/O1 data receive
At completion of serial I/O1 transmit shift
or when transmit buffer is empty
At completion of serial I/O2 data receive
At completion of serial I/O2 transmit shift
or when transmit buffer is empty
At detection of either rising or falling edge
of INT0 input
At detection of either rising or falling edge
of INT1 input
At falling of conjunction of input logical
level for port P0 (at input)
At detection of UART1 bus collision
detection
At detection of either rising or falling edge
of CNTR0 input
Remarks
Non-maskable
Valid only when serial I/O1 is selected
Valid only when serial I/O1 is selected
Valid only when serial I/O2 is selected
Valid only when serial I/O2 is selected
External interrupt
(active edge selectable)
External interrupt
(active edge selectable)
External interrupt (valid at falling, when
key-on wakeup interrupt is enabled)
When UART1 bus collision detection
interrupt is enabled.
External interrupt
(active edge selectable)
At detection of either rising or falling edge External interrupt
(active edge selectable)
of Capture 0 input
At detection of either rising or falling edge External interrupt
(active edge selectable)
of Capture 1 input
Compare interrupt source is selected.
At compare matched
At timer X underflow
At timer A underflow
At timer B underflow
At completion of A/D conversion
At timer 1 underflow
At BRK instruction execution
When A/D conversion interrupt is enabled.
STP release timer underflow
(When Timer 1 interrupt is enabled)
Non-maskable software interrupt
Note 1: Vector addressed contain internal jump destination addresses.
2: Reset function in the same way as an interrupt with the highest priority.
3: Key-on wakeup interrupt and UART1 bus collision detection interrupt can be enabled by setting of interrupt source set register. The occurrence of
these interrupts are discriminated by interrupt source discrimination register.
4: A/D conversion interrupt and Timer 1 interrupt can be enabled by setting of interrupt source set register. The occurrence of these interrupts are discriminated by interrupt source discrimination register.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 23 of 93
7546 Group
Key-on wakeup interrupt
discrimination bit
Key-on wakeup interrupt request
Key-on wakeup interrupt valid bit
UART1 bus collision detection
interrupt request
UART1 bus
collision detection
interrupt
discrimination bit
Key-on wakeup/
UART1 bus collision
detection interrupt
request bit
UART1 bus collision detection
interrupt valid bit
A/D conversion interrupt
discrimination bit
A/D conversion interrupt request
A/D conversion interrupt valid bit
Timer 1 interrupt request
Timer 1 interrupt
discrimination bit
A/D conversion/
Timer 1 interrupt
request bit
Timer 1 interrupt valid bit
Interrupt request bit
Interrupt enable bit
Interrupt disable flag I
BRK instruction
Reset
Interrupt request
Note: For key-on wakeup, UART1 bus collision detection, A/D conversion and Timer 1 interrupt,
even if interrupt valid bit (000A16) is set “0: Invalid”,
interrupt discrimination bit (000B16) is set to “1: interrupt occurs”
when corresponding interrupt request occurs.
But corresponding interrupt request bit (003C16, 003D16) is not set to “1”.
Fig. 20 Interrupt control
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 24 of 93
7546 Group
b7
b0
Interrupt source set register
(INTSET: address 000A16, initial value: 0016)
Key-on wakeup interrupt valid bit
b7
Serial I/O1 receive interrupt request bit
Serial I/O1 transmit interrupt request bit
Serial I/O2 receive interrupt request bit
Serial I/O2 transmit interrupt request bit
INT0 interrupt request bit
INT1 interrupt request bit
Key-on wake up/UART1 bus collision detection
interrupt request bit
CNTR0 interrupt request bit
0 : No interrupt request issued
1 : Interrupt request issued
UART1 bus collision detection interrupt valid bit
A/D conversion interrupt valid bit
Timer 1 interrupt valid bit
Not used (returns “0” when read)
0: Interrupt invalid
1: Interrupt valid
b7
b0
Interrupt source discrimination register
(INTDIS: address 000B16, initial value: 0016)
Key-on wakeup interrupt discrimination bit
UART1 bus collision detection
interrupt discrimination bit
b0 Interrupt request register 1
(IREQ1 : address 003C16, initial value : 0016)
b7
b0 Interrupt request register 2
(IREQ2 : address 003D16, initial value : 0016)
A/D conversion interrupt discrimination bit
Timer 1 interrupt discrimination bit
Capture 0 interrupt request bit
Capture 1 interrupt request bit
Compare interrupt request bit
Timer X interrupt request bit
Timer A interrupt request bit
Timer B interrupt request bit
A/D conversion/Timer 1 interrupt request bit
Not used (returns “0” when read)
(Do not write “1” to this bit)
Not used (returns “0” when read)
0: Interrupt does not occur
1: Interrupt occurs
b7
b0
Interrupt edge selection register
(INTEDGE : address 003A16, initial value: 0016)
INT0 interrupt edge selection bit
0 : Falling edge active
1 : Rising edge active
INT1 interrupt edge selection bit
0 : Falling edge active
1 : Rising edge active
Set “1” to this bit certainly.
0 : No interrupt request issued
1 : Interrupt request issued
b7
b0 Interrupt control register 1
(ICON1 : address 003E16, initial value : 0016)
Not used (returns “0” when read)
Serial I/O1 receive interrupt enable bit
Serial I/O1 transmit interrupt enable bit
Serial I/O2 receive interrupt enable bit
Serial I/O2 transmit interrupt enable bit
INT0 interrupt enable bit
INT1 interrupt enable bit
Key-on wake up/UART1 bus collision
detection interrupt enable bit
CNTR0 interrupt enable bit
P00 key-on wakeup enable bit
0 : Key-on wakeup enabled
1 : Key-on wakeup disabled
P04 key-on wakeup enable bit
0 : Key-on wakeup enabled
1 : Key-on wakeup disabled
P06 key-on wakeup enable bit
0 : Key-on wakeup enabled
1 : Key-on wakeup disabled
b7
0 : Interrupts disabled
1 : Interrupts enabled
b0 Interrupt control register 2
(ICON2 : address 003F16, initial value : 0016)
Capture 0 interrupt enable bit
Capture 1 interrupt enable bit
Compare interrupt enable bit
Timer X interrupt enable bit
Timer A interrupt enable bit
Timer B interrupt enable bit
A/D conversion/Timer 1 interrupt enable bit
Not used (returns “0” when read)
(Do not write “1” to this bit)
0 : Interrupts disabled
1 : Interrupts enabled
Fig. 21 Structure of Interrupt-related registers
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 25 of 93
7546 Group
Key Input Interrupt (Key-On Wake-Up)
A key-on wake-up interrupt request is generated by applying “L”
level to any pin of port P0 that has been set to input mode.
In other words, it is generated when the AND of input level goes
from “1” to “0”. An example of using a key input interrupt is shown
in Figure 22, where an interrupt request is generated by pressing
one of the keys provided as an active-low key matrix which uses
ports P00 to P03 as input ports.
Port PXx
“L” level output
PULL register
bit 3 = “0”
*
**
P07 output
Port P07
Direction register = “1”
Key input interrupt request
Port P07
latch
Falling edge
detection
PULL register
bit 3 = “0”
*
**
P06 output
Port P06
Direction register = “1”
Port P06
latch
Falling edge
detection
Port P06 key-on wakeup
selection bit
PULL register
bit 3 = “0”
*
**
P05 output
Port P05
Direction register = “1”
Port P05
latch
Falling edge
detection
PULL register
bit 3 = “0”
*
**
P04 output
Port P04
Direction register = “1”
Port P04
latch
Falling edge
detection
Port P04 key-on wakeup
selection bit
PULL register
bit 2 = “1”
*
**
P03 input
Port P03
Direction register = “0”
Port P03
latch
Falling edge
detection
PULL register
bit 2 = “1”
*
**
P02 input
Port P02
Direction register = “0”
Port P02
latch
Falling edge
detection
PULL register
bit 1 = “1”
*
**
P01 input
Port P01
Direction register = “0”
Port P01
latch
Falling edge
detection
PULL register
bit 0 = “1”
*
**
P00 input
Port P00
Direction register = “0”
Port P00
latch
Falling edge
detection
Port P00 key-on wakeup
selection bit
* P-channel transistor for pull-up
** CMOS output buffer
Fig. 22 Connection example when using key input interrupt and port P0 block diagram
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 26 of 93
Port P0
Input read circuit
7546 Group
Timers
●Timer X
The 7546 Group has 4 timers: timer 1, timer X, timer A and timer
B.
The division ratio of every timer and prescaler is 1/(n+1) provided
that the value of the timer latch or prescaler is n.
All the timers are down count timers. When a timer reaches “0”, an
underflow occurs at the next count pulse, and the corresponding
timer latch is reloaded into the timer. When a timer underflows, the
interrupt request bit corresponding to each timer is set to “1”.
Timer X is an 8-bit timer and counts the prescaler X output.
When Timer X underflows, the timer X interrupt request bit is set
to “1”.
Prescaler X is an 8-bit prescaler and counts the signal selected by
the timer X count source selection bit.
Prescaler X and Timer X have the prescaler X latch and the timer
X latch to retain the reload value, respectively. The value of
prescaler X latch is set to Prescaler X when Prescaler X
underflows.The value of timer X latch is set to Timer X when Timer
X underflows.
When writing to Prescaler X (PREX) is executed, the value is written to both the prescaler X latch and Prescaler X.
When writing to Timer X (TX) is executed, the value is written to
both the timer X latch and Timer X.
When reading from Prescaler X (PREX) and Timer X (TX) is executed, each count value is read out.
• Frequency divider for timer
According to the clock division selection bits (b7 and b6) of CPU
mode register (003B16), the count source of frequency divider is
set as follows;
b7b6 = “00”(high-speed), “01”(middle-speed), “11”(double-speed): XIN
b7b6 = “10”(On-chip oscillator): On-chip oscillator
●Timer 1
Timer 1 is an 8-bit timer and counts the prescaler output.
When Timer 1 underflows, the timer 1 interrupt request bit is set to
“1”.
Prescaler 1 is an 8-bit prescaler and counts the signal which is the
oscillation frequency divided by 16.
Prescaler 1 and Timer 1 have the prescaler 1 latch and the timer 1
latch to retain the reload value, respectively. The value of
prescaler 1 latch is set to Prescaler 1 when Prescaler 1
underflows. The value of timer 1 latch is set to Timer 1 when Timer
1 underflows.
When writing to Prescaler 1 (PRE1) is executed, the value is written to both the prescaler 1 latch and Prescaler 1.
When writing to Timer 1 (T1) is executed, the value is written to
both the timer 1 latch and Timer 1.
When reading from Prescaler 1 (PRE1) and Timer 1 (T1) is executed, each count value is read out.
Timer 1 always operates in the timer mode.
Prescaler 1 counts the signal which is the oscillation frequency divided by 16. Each time the count clock is input, the contents of
Prescaler 1 is decremented by 1. When the contents of Prescaler
1 reach “0016”, an underflow occurs at the next count clock, and
the prescaler 1 latch is reloaded into Prescaler 1 and count continues. The division ratio of Prescaler 1 is 1/(n+1) provided that the
value of Prescaler 1 is n.
The contents of Timer 1 is decremented by 1 each time the underflow signal of Prescaler 1 is input. When the contents of Timer 1
reach “0016”, an underflow occurs at the next count clock, and the
timer 1 latch is reloaded into Timer 1 and count continues. The division ratio of Timer 1 is 1/(m+1) provided that the value of Timer
1 is m. Accordingly, the division ratio of Prescaler 1 and Timer 1 is
1/((n+1)✕(m+1)) provided that the value of Prescaler 1 is n and
the value of Timer 1 is m.
Timer 1 cannot stop counting by software.
Timer X can be selected in one of 4 operating modes by setting
the timer X operating mode bits of the timer X mode register.
(1) Timer mode
Prescaler X counts the count source selected by the timer X count
source selection bits. Each time the count clock is input, the contents of Prescaler X is decremented by 1. When the contents of
Prescaler X reach “0016”, an underflow occurs at the next count
clock, and the prescaler X latch is reloaded into Prescaler X and
count continues. The division ratio of Prescaler X is 1/(n+1) provided that the value of Prescaler X is n.
The contents of Timer X is decremented by 1 each time the underflow signal of Prescaler X is input. When the contents of Timer X
reach “0016”, an underflow occurs at the next count clock, and the
timer X latch is reloaded into Timer X and count continues. The division ratio of Timer X is 1/(m+1) provided that the value of Timer
X is m. Accordingly, the division ratio of Prescaler X and Timer X is
1/((n+1)✕(m+1)) provided that the value of Prescaler X is n and
the value of Timer X is m.
(2) Pulse output mode
In the pulse output mode, the waveform whose polarity is inverted
each time timer X underflows is output from the CNTR0 pin.
The output level of CNTR0 pin can be selected by the CNTR0 active edge switch bit. When the CNTR0 active edge switch bit is “0”,
the output of CNTR0 pin is started at “H” level. When this bit is “1”,
the output is started at “L” level.
Also, the inverted waveform of pulse output from CNTR0 pin can
be output from TXOUT pin by setting “1” to the P03/TXOUT output
valid bit.
When using a timer in this mode, set the port P14 and P03 direction registers to output mode.
(3) Event counter mode
The timer A counts signals input from the P14/CNTR0 pin.
Except for this, the operation in event counter mode is the same
as in timer mode.
The active edge of CNTR0 pin input signal can be selected from
rising or falling by the CNTR0 active edge switch bit .
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 27 of 93
7546 Group
(4) Pulse width measurement mode
In the pulse width measurement mode, the pulse width of the signal input to P14/CNTR0 pin is measured.
The operation of Timer X can be controlled by the level of the signal input from the CNTR0 pin.
When the CNTR0 active edge switch bit is “0”, the signal selected
by the timer X count source selection bit is counted while the input
signal level of CNTR0 pin is “H”. The count is stopped while the
pin is “L”. Also, when the CNTR0 active edge switch bit is “1”, the
signal selected by the timer X count source selection bit is
counted while the input signal level of CNTR0 pin is “L”. The count
is stopped while the pin is “H”.
b7
b0
Timer X mode register
(TXM : address 002B16, initial value: 0016)
Timer X operating mode bits
b1 b0
0 0 : Timer mode
0 1 : Pulse output mode
1 0 : Event counter mode
1 1 : Pulse width measurement mode
CNTR0 active edge switch bit
0 : Interrupt at falling edge
Count at rising edge
(in event counter mode)
1 : Interrupt at rising edge
Count at falling edge
(in event counter mode)
Timer X count stop bit
0 : Count start
1 : Count stop
Timer X can stop counting by setting “1” to the timer X count stop
bit in any mode.
Also, when Timer X underflows, the timer X interrupt request bit is
set to “1”.
Note on Timer X is described below;
■ Note on Timer X
(1) CNTR0 interrupt active edge selection-1
CNTR0 interrupt active edge depends on the CNTR0 active edge
switch bit.
When this bit is “0”, the CNTR0 interrupt request bit is set to “1” at
the falling edge of CNTR0 pin input signal. When this bit is “1”, the
CNTR 0 interrupt request bit is set to “1” at the rising edge of
CNTR0 pin input signal.
(2) CNTR0 interrupt active edge selection-2
According to the setting value of CNTR0 active edge switch bit,
the interrupt request bit may be set to “1”.
When not requiring the interrupt occurrence synchronized with
these setting, take the following sequence.
➀ Set the corresponding interrupt enable bit to “0” (disabled).
➁ Set the active edge switch bit.
➂ Set the corresponding interrupt request bit to “0” after 1 or more
instructions have been executed.
➃ Set the corresponding interrupt enable bit to “1” (enabled).
P03/TXOUT output valid bit
0 : Output invalid (I/O port)
1 : Output valid (Inverted CNTR0 output)
Not used (return “0” when read)
Fig. 23 Structure of timer X mode register
b7
b0
Timer count source set register
(TCSS : address 002A16, initial value: 0016)
Timer X count source selection bits
b1 b0
0 0 : f(XIN)/16
0 1 : f(XIN)/2
1 0 : f(XIN) (Note 1)
1 1 : Not available
Timer A count source selection bits
b4 b3 b2
0 0 0 : f(XIN)/16
0 0 1 : f(XIN)/2
0 1 0 : f(XIN)/32
0 1 1 : f(XIN)/64
1 0 0 : f(XIN)/128
1 0 1 : f(XIN)/256
1 1 0 : On-chip oscillator output (Note 2)
1 1 1 : Not available
Timer B count source selection bits
b7 b6 b5
0 0 0 : f(XIN)/16
0 0 1 : f(XIN)/2
0 1 0 : f(XIN)/32
0 1 1 : f(XIN)/64
1 0 0 : f(XIN)/128
1 0 1 : f(XIN)/256
1 1 0 : Timer A underflow
1 1 1 : Not available
Notes 1: f(XIN) can be used as timer X count source when using
a ceramic resonator or on-chip oscillator.
Do not use it at RC oscillation.
2: On-chip oscillator can be used when the on-chip oscillator
is enabled by bit 3 of CPUM.
Fig. 24 Timer count source set register
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 28 of 93
7546 Group
Data bus
Prescaler 1 latch (8)
Timer 1 latch (8)
Prescaler 1 (8)
1/16
“00”
“01”
“11”
Clock
division ratio
selection bits
XIN
On-chip
“10”
oscillator
CPU mode register
Data bus
Frequency Timer X count
source selection bits
divider
1/16
1/2
1/1
Prescaler X latch (8)
Timer X latch (8)
Pulse width
measurement Timer mode
Pulse output mode
mode
Prescaler X (8)
P14/CNTR0
Timer 1 interrupt
request
Timer 1 (8)
CNTR0 active
edge switch bit
“0”
Event
counter
mode
Timer X (8)
Timer X count stop bit
CNTR0
interrupt
request bit
“1”
CNTR0 active “1”
edge switch bit
Q
Q
Port P14
latch
Port P14 direction
register
Pulse output mode
P03/TXOUT
Port P03 latch
P03/TXOUT output valid
Port P03
direction
register
Fig. 25 Block diagram of timer 1 and timer X
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 29 of 93
Timer X
interrupt
request bit
“0”
Toggle flip-flop T
R
Writing to timer X latch
Pulse output mode
7546 Group
●Timer A,B
■ Notes on Timer A, B
Timer A and Timer B are 16-bit timers and counts the signal which
is the oscillation frequency selected by setting of the timer count
source set register (TCSS). Timer A and Timer B have the same
function except of the count source clock selection.
(1) Setting of timer value
When “1: Write to only latch” is set to the timer A (B) write control
bit, written data to timer register is set to only latch even if timer is
stopped. Accordingly, in order to set the initial value for timer when
it is stopped, set “0: Write to latch and timer simultaneously” to
timer A (B) write control bit.
The count source clock of Timer A is selected from among 1/2,1/
16, 1/32, 1/64, 1/128, 1/256 of f(XIN) clock and on-chip oscillator
clock.
The count source clock of Timer B is selected from among 1/2, 1/
16, 1/32, 1/64, 1/128, 1/256 of f(XIN) clock and Timer A underflow.
Timer A (B) consists of the low-order of Timer A: TAL (Timer B:
TBL) and the high-order of Timer A: TAH (Timer B: TBH). Timer A
(B) is decremented by 1 when each time of the count clock is input. When the contents of Timer A (B) reach “0000 16 ”, an
underflow occurs at the next count clock, and the timer latch is reloaded into timer. When Timer A (B) underflows, the Timer A (B)
interrupt request bit is set to “1”.
Timer A (B) has the Timer A (B) latch to retain the load value. The
value of timer A (B) latch is set to Timer A (B) at the timing of Timer
A (B) underflow. The division ratio of Timer A (B) is 1/(n+1) provided that the value of Timer A (B) is n.
When writing to both the low-order of Timer A (B) and the high order of Timer A (B) is executed, writing to “latch only” or “latch and
timer” can be selected by the setting value of the timer A (B) write
control bit.
When reading from Timer A (B) register is executed, the count
value of Timer A (B) is read out.
Be sure to write to/read out the low-order of Timer A (B) and the
high-order of Timer A (B) in the following order;
• Read
Read the high-order of Timer A (B) first, and the low-order of Timer
A (B) next and be sure to read both high-order and low-order.
• Write
Write to the low-order of Timer A (B) first, and the high-order of
Timer A (B) next and be sure to write both low-order and high order.
Timer A and Timer B can be used for the timing timer of Input capture and Output compare function.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 30 of 93
(2) Read/write of timer A
Stop timer A to read/write its data when the system is in the following state;
• CPU operation clock source: XIN oscillation
• Timer A count source: On-chip oscillator output
(3) Read/write of timer B
Stop timer B to read/write its data when the system is in the following state;
• CPU operation clock source: XIN oscillation
• Timer B count source: Timer A underflow
• Timer A count source: On-chip oscillator output
7546 Group
b7
b0
b7
Timer A, B mode register
(TABM : address 001D16, initial value: 0016)
Timer count source set register
(TCSS : address 002A16, initial value: 0016)
Timer X count source selection bits
b1 b0
0 0 : f(XIN)/16
0 1 : f(XIN)/2
1 0 : f(XIN) (Note 1)
1 1 : Not available
Timer A write control bit
0 : Write to latch and timer simultaneously
1 : Write to only latch
Timer A count stop bit
0 : Count start
1 : Count stop
Timer A count source selection bits
b4 b3 b2
0 0 0 : f(XIN)/16
0 0 1 : f(XIN)/2
0 1 0 : f(XIN)/32
0 1 1 : f(XIN)/64
1 0 0 : f(XIN)/128
1 0 1 : f(XIN)/256
1 1 0 : On-chip oscillator output (Note 2)
1 1 1 : Not available
Timer B count source selection bits
b7 b6 b5
0 0 0 : f(XIN)/16
0 0 1 : f(XIN)/2
0 1 0 : f(XIN)/32
0 1 1 : f(XIN)/64
1 0 0 : f(XIN)/128
1 0 1 : f(XIN)/256
1 1 0 : Timer A underflow
1 1 1 : Not available
Timer B write control bit
0 : Write to latch and timer simultaneously
1 : Write to only latch
Timer B count stop bit
0 : Count start
1 : Count stop
Not used (return “0” when read)
Compare 0, 1 modulation mode bit
0: Disabled
1: Enabled
Compare 2, 3 modulation mode bit
0: Disabled
1: Enabled
Fig. 26 Structure of timer A, B mode register
b0
Notes 1: f(XIN) can be used as timer X count source when using
a ceramic resonator or on-chip oscillator.
Do not use it at RC oscillation.
2: On-chip oscillator can be used when the on-chip oscillator
is enabled by bit 3 of CPUM.
Fig. 27 Timer count source set register
Clock division
ratio selection
“00”
bits
“01”
“11”
XIN
On-chip
oscillator “10”
CPU mode register
Frequency
divider
Data bus
1/2
1/16
1/32
Timer A (low-order) latch (8)
1/64
Timer A (high-order) latch (8)
Timer A write
control bit
1/128
1/256
On-chip
oscillator
Timer A (low-order) (8)
Timer A
count source
selection bits
Timer A (high-order) (8)
Timer A count
stop bit
Frequency
divider
1/2
Timer A interrupt
request
Compare
Capture
Data bus
1/16
1/32
Timer B (low-order) latch (8)
1/64
Timer B (high-order) latch (8)
Timer B write
control bit
1/128
1/256
Timer B (low-order) (8)
Timer B count source
selection bits
Timer B count
stop bit
Fig. 28 Block diagram of timer A and timer B
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 31 of 93
Timer B (high-order) (8)
Timer B interrupt
request
Compare
Capture
7546 Group
Output compare
7546 group has 4-output compare channels. Each channel (0 to 3)
has the same function and can be used to output waveform by using count value of either Timer A or Timer B.
The source timer for each channel is selected by setting value of
the compare x (x = 0, 1, 2, 3) timer source bit. Timer A and Timer B
can be selected for the source timer to each channel, respectively.
To use each compare channel, set “1” to the compare x output
port bit and set the port direction register corresponding to compare channel to output mode.
The compare value for each channel is set to the compare register (low-order) and compare register (high-order).
Writing to the register for each channel is controlled by setting
value of compare register write pointer. Writing to each register is
in the following order;
1.Set the value of corresponded output compare channel to the
compare register write pointer.
2.Write a value to the compare register (low-order) and compare
register (high-order).
3.Set “1” to the compare latch y (y = 00, 01, 10, 11, 20, 21, 30, 31)
re-load bit.
When “1” is set to the compare latch y re-load bit, the value set
to the compare register is loaded to compare latch when the
next timer underflow.
■ Notes on Output Compare
• When the selected source timer of each compare channel is
stopped, written data to compare register is loaded to the compare latch simultaneously.
• Do not write the same data to both of compare latch x0 and x1.
• When setting value of the compare latch is larger than timer setting value, compare match signal is not generated. Accordingly,
the output waveform is fixed to “L” or “H” level.
However, when setting value of another compare latch is
smaller than timer setting value, this compare match signal is
generated. Accordingly, compare match interrupt occurs.
• When the compare x trigger enable bit is cleared to “0” (disabled), the match trigger to the waveform output circuit is
disabled, and the output waveform can be fixed to “L” or “H”
level.
However, in this case, the compare match signal is generated.
Accordingly, compare match interrupt occurs.
b7
b0
Capture/compare register R/W pointer
(CCRP : address 001216, initial value: 0016)
Compare register R/W pointer
b2 b1 b0
0 0 0 : Compare latch 00
0 0 1 : Compare latch 01
0 1 0 : Compare latch 10
0 1 1 : Compare latch 11
1 0 0 : Compare latch 20
1 0 1 : Compare latch 21
1 1 0 : Compare latch 30
1 1 1 : Compare latch 31
When count value of timer and setting value of compare latch is
matched, compare output trigger occurs.
When “1: Enabled” is set to the compare trigger x enable bit, the
output waveform from port is inverted by compare trigger.
When “0: Disabled” is set to the compare trigger x enable bit, the output waveform is not inverted, so port output can be fixed to “H” or “L”.
When “0: Positive” is set to the compare x output level latch, the
compare output waveform is turned to “H level” at compare latch
x0’s match and turned to “L level” at compare latch x1’s match.
When “1 :Negative” is set to the compare x output level latch, the
compare output waveform is turned to “L level” at compare latch
x0’s match and turned to “H level” at compare latch x1’s match.
The compare output level of each channel can be confirmed by
reading the compare x output status bit.
Compare output interrupt is available when match of each compare channel and timer count value. The interrupt request from
each channel can be disabled or enabled by setting value of compare latch y interrupt source bit.
Compare 0,1 (2,3) modulation mode
In compare modulation mode, modulation waveform can be generated by using compare channel 0 and 1, or compare channel 2 and 3.
To use this mode,
• Set “1: Enabled” to the compare 0,1 (2, 3) modulation mode bit.
• Set Timer A underflow for Timer B count source.
• Set Timer A for the timer source of compare channel 0 (2).
• Set Timer B for the timer source of compare channel 1 (3).
In this mode, AND waveform of compare 0 (1) and compare 2 (3)
is generated from Port P01 and P31, respectively. Accordingly, in
order to use this mode, set “1” to the compare 0 output port bit or
compare 2 output port bit.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 32 of 93
Not used (returns “0” when read)
Capture register 0 R/W pointer
0: Capture latch 00
1: Capture latch 01
Capture register 1 R/W pointer
0: Capture latch 10
1: Capture latch 11
Not used (returns “0” when read)
Fig. 29 Structure of capture/compare register R/W pointer
b7
b0
Compare register re-load register
(CMPR : address 001416, initial value: 0016)
Compare latch 00, 01 re-load bit
0: Re-load disabled
1: Re-load at next underflow
Compare latch 10, 11 re-load bit
0: Re-load disabled
1: Re-load at next underflow
Compare latch 20, 21 re-load bit
0: Re-load disabled
1: Re-load at next underflow
Compare latch 30, 31 re-load bit
0: Re-load disabled
1: Re-load at next underflow
Not used (returns “0” when read)
Fig. 30 Structure of compare register re-load register
7546 Group
b7
b0
Capture/Compare port register
(CCPR : address 001E16, initial value: 0016)
Capture 0 input port bits
b1 b0
0 0: Capture from P00
0 1: Capture from P10
1 0: Ring/512
1 1: Not available
b7
b0
Capture/Compare status register
(CCSR : address 002216, initial value: 0016)
Compare 0 output status bit
0: “L” level output
1: “H” level output
Compare 1 output status bit
0: “L” level output
1: “H” level output
Compare 0 output port bit
0: P01 is I/O port
1: P01 is Compare 0
Compare 2 output status bit
0: “L” level output
1: “H” level output
Compare 1 output port bit
0: P02 is I/O port
1: P02 is Compare 1
Capture 1 input port bit
0: Capture from P30
1: Ring/512
Compare 3 output status bit
0: “L” level output
1: “H” level output
Compare 2 output port bit
0: P31 is I/O port
1: P31 is Compare 2
Capture 0 status bit
0: latch 00 captured
1: latch 01 captured
Compare 3 output port bit
0: P32 is I/O port
1: P32 is Compare 3
Capture 1 status bit
0: latch 10 captured
1: latch 11 captured
Not used (returns “0” when read)
Fig. 31 Structure of capture/compare port register
b7
Not used (returns “0” when read)
Fig. 34 Structure of capture/compare status register
b0
Timer source selection register
(TMSR : address 001F16, initial value: 0016)
Compare 0 timer source bit
Compare 1 timer source bit
Compare 2 timer source bit
b7
b0
Compare interrupt source register
(CISR : address 002316, initial value: 0016)
Compare latch 00 interrupt source bit
Compare latch 01 interrupt source bit
Compare 3 timer source bit
Compare latch 10 interrupt source bit
Capture 0 timer source bit
Compare latch 11 interrupt source bit
Capture 1 timer source bit
Compare latch 20 interrupt source bit
Not used (returns “0” when read)
Compare latch 21 interrupt source bit
0: Timer A
1: Timer B
Compare latch 30 interrupt source bit
Compare latch 31 interrupt source bit
Fig. 32 Structure of timer source selection register
b7
0: Disabled
1: Enabled
b0
Compare output mode register
(CMOM : address 002116, initial value: 0016)
Compare 0 output level latch
0: Positive
1: Negative
Compare 1 output level latch
0: Positive
1: Negative
Compare 2 output level latch
0: Positive
1: Negative
Compare 3 output level latch
0: Positive
1: Negative
Compare 0 trigger enable bit
0: Disabled
1: Enabled
Compare 1 trigger enable bit
0: Disabled
1: Enabled
Compare 2 trigger enable bit
0: Disabled
1: Enabled
Compare 3 trigger enable bit
0: Disabled
1: Enabled
Fig. 33 Structure of compare output mode register
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 33 of 93
Fig. 35 Structure of compare interrupt source register
7546 Group
Compare latch 00
Compare latch 01
P01/CMP0
Timer A latch
Wave latch channel 0
Timer A counter
Compare 0 timer source bit
Timer B counter
Compare channel 0
P02/CMP1
P31/CMP2
P32/CMP3
Timer B latch
Compare channel 1
Compare channel 2
Compare channel 3
Fig. 36 Block diagram of output compare
Data bus
Compare register
write pointer
(001216, bits 0 to 2)
Compare buffer 00 (16)
Compare buffer 01 (16)
Compare latch 00, 01
re-load bit
(001416, bit 0)
Compare latch 00 (16)
Compare 0 output
port bit
(001E16, bit 2)
Compare 0 output
status bit
(002216, bit 0)
Compare 0 trigger
enable bit
(002116, bit 4)
Compare latch 01 (16)
Compare register
I/O port
Output latch
P01/CMP0
Timer A counter (16)
Compare 0 output
level latch
(002116, bit 0)
Compare interrupt
Fig. 37 Block diagram of compare channel 0
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 34 of 93
Compare latch 00
interrupt source
bit (002316, bit 0)
Compare latch 01
interrupt source
bit (002316, bit 1)
Timer B counter (16)
Compare 0 timer
source bit
(001F16, bit 0)
7546 Group
Data bus
P01/CMP0
Compare register
write pointer
(001216, bits 0 to 2)
I/O
port
Compare buffer 00 (16)
Compare buffer 01 (16)
Compare latch 00, 01
re-load bit
(001416, bit 0)
Compare 0 output
port bit
(001E16, bit 2)
Compare latch 00 (16)
Compare 0 output
status bit
(002216, bit 0)
Compare latch 01 (16)
Compare register
Compare 0 trigger
enable bit
(002116, bit 4)
Output latch
Timer A counter (16)
Compare 0 output
level latch
(002116, bit 0)
Compare 0 (1)
timer source bits
(001F16, bit 0 (bit 1)
Compare 1 output
status bit
(002216, bit 1)
Underflow
Compare 1 trigger
enable bit
(002116, bit 5)
Timer B counter (16)
Output latch
Compare 1 output
level latch
(002116, bit 1)
Compare register
Compare latch 10 (16)
Compare latch 11 (16)
Compare latch 10, 11
re-load bit
(001416, bit 1)
Compare buffer 10 (16)
Compare register
write pointer
(001216, bits 0 to 2)
Data bus
Fig. 38 Block diagram at modulation mode
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 35 of 93
Compare buffer 11 (16)
7546 Group
Timer count clock
Re-load the count value
Timer underflow
Timer count value 000C 000B 000A 0009 0008 0007 0006 0005 0004 0003 0002 0001 0000 000F 000E 000D 000C 000B
Compare latch 00
000B
Compare latch 01
0005
Compare 00 match
Compare 01 match
Compare output
Compare interrupt
Compare status bit
0
1
0
Note: Compare interrupt occurs only for the interrupt source selected by Compare interrupt source register.
Fig. 39 Output compare mode (general waveform)
Timer count clock
Re-load the count value
Timer underflow
Timer count value 000C 000B 000A 0009 0008 0007 0006 0005 0004 0003 0002 0001 0000 000F 000E 000D 000C 000B
Compare latch 00
000B
000E
Compare latch 01
0005
000C
Compare latch 00 write
Compare latch 01 write
Compare latch 00, 01 re-load bit
Compare latch 00, 01 re-load signal
Compare 00 match
Compare 01 match
Compare output
Compare interrupt
Compare status bit
0
1
Fig. 40 Output compare mode (compare register write timing)
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 36 of 93
0
1
0
7546 Group
Carrier wave generated by Compare 0
Timer A count clock
Timer A underflow
Timer A count value 0004 0003 0002 0001 0000 0007 0006 0005 0004 0003 0002 0001 0000 0007 0006 0005 0004 0003
Compare latch 00
0006
Compare latch 01
0002
Compare 00 match
Compare 01 match
Compare 0 output
Compare 0 output status bit
1
0
1
0
1
Modulation of output waveform generated by Compare 1
Timer A underflow
Compare 0 output
Timer B count value 0004 0003 0002 0001 0000 0007 0006 0005 0004 0003 0002 0001 0000 0007 0006 0005 0004 0003
Compare latch 10
0004
Compare latch 11
0001
Compare 10 match
Compare 11 match
Compare 1 output
Compare interrupt
Compare 1 output status bit
0
1
0
1
0
Port outptu wavefowm
Modulation output
Note: Compare interrupt occurs only for the interrupt source selected by Compare interrupt source register.
Fig. 41 Output compare mode (compare 0, 1 modulation mode)
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 37 of 93
1
7546 Group
1. When Compare 0 output level latch is “Positive”, Compare 1 output level latch is “Positive”.
Compare 0 output
Compare 1 output
Modulation output
2. When Compare 0 output level latch is “Negative”, Compare 1 output level latch is “Positive”.
Compare 0 output
Compare 1 output
Modulation output
3. When Compare 0 output level latch is “Positive”, Compare 1 output level latch is “Negative”.
Compare 0 output
Compare 1 output
Modulation output
4. When Compare 0 output level latch is “Negative”, Compare 1 output level latch is “Negative”.
Compare 0 output
Compare 1 output
Modulation output
Fig. 42 Output compare mode (compare 0, 1 modulation mode: effect of output level latch)
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 38 of 93
7546 Group
Input capture
■ Notes on Input Capture
7546 group has 2-input capture channels. Each channel (0 and 1)
has the same function and can be used to capture count value of
either Timer A or Timer B.
The source timer for each channel is selected by setting value of
the capture x (x = 0, 1) timer source bit. Timer A and Timer B can
be selected for the source timer to each channel, respectively.
• If the capture trigger is input while the capture register (low-order
and high-order) is in read, captured value is changed between
high-order reading and low-order reading. Accordingly, some
countermeasure by program is recommended, for example
comparing the values that twice of read.
• When CPU operation clock source is XIN oscillation and the onchip-oscillator is selected for Timer A count source, Timer A
cannot be used for the capture source timer.
Timer B cannot be used for the capture source timer when the
system is in the following state;
• CPU operation clock source: XIN oscillation
• Timer B count source: Timer A underflow
• Timer A count source: On-chip oscillator output
• When writing “1” to capture latch x0 (x1) software trigger bit of
capture latch x0 and x1 at the same time, or external trigger and
software trigger occur simultaneously, the set value of capture x
status bit is undefined.
• When setting the interrupt active edge selection bit and noise filter clock selection bit of external interrupt CAP 0 , CAP1 , the
interrupt request bit may be set to “1”.
When not requiring the interrupt occurrence synchronized with
these setting, take the following sequence.
➀ Set the corresponding interrupt enable bit to “0” (disabled).
➁ Set the interrupt edge selection bit or noise filter clock selection bit.
➂ Set the corresponding interrupt request bit to “0” after 1 or more
instructions have been executed.
➃ Set the corresponding interrupt enable bit to “1” (enabled).
• When the capture interrupt is used as the interrupt for return
from stop mode, set the capture x noise filter clock selection bits
to “00 (Filter stop)”.
To use each capture channel, set the capture x input port bits and
set the port direction register corresponding to capture channel to
input mode.
The input capture circuit retains the count value of selected timer
when external trigger is input. The timer count value is retained to
the capture latch x0 when rising edge is input and is retained to
the capture latch x1 when falling edge is input.
The count value of timer can be retained by software by capture y
(y = 00, 01, 10, 11) software trigger bit too. When “1” is set to this
bit, count value of timer is retained to the corresponded capture
latch.
When reading from the capture y software trigger bit is executed,
“0” is read out.
The latest status of capture latch can be confirmed by reading of
the capture x status bit. This bit indicates the capture latch which
latest data is in.
The valid trigger edge for capture interrupt is set by the capture x
interrupt edge selection bits. (Regardless of the setting value of
capture x interrupt edge selection bits, timer count values for both
edges are retained to the capture latch.)
Each capture input has the noise filter circuit that judges continuous 4-time same level with sampling clock to be valid. The
sampling clock of noise filter is set by the capture x noise filter
clock selection bits.
Reading from the register for each channel is controlled by setting
value of the capture register read pointer. Reading from each register is in the following order;
1.Set the value of the corresponded input capture channel to the
capture register read pointer.
2.Read from the capture register (low-order) and capture register
(high-order).
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 39 of 93
7546 Group
b7
b7
b0
b0
Capture software trigger register
(CSTR : address 001316, initial value: 0016)
Capture latch 00 software trigger bit
Capture register 0 (Low-order)
(CAP0L : address 000C16)
b7
b7
b7
Capture latch 01 software trigger bit
b0
Capture register 0 (High-order)
(CAP0H : address 000D16)
Capture latch 10 software trigger bit
Capture register 1 (Low-order)
(CAP1L : address 000E16)
Each software trigger occurs by setting “1” to
corresponding bit. (returns “0” when read)
Capture latch 11 software trigger bit
b0
Not used (returns “0” when read)
b0
Capture register 1 (High-order)
(CAP1H : address 000F16)
Fig. 43 Structure of capture software trigger register
b7
b0
Capture mode register
(CAPM : address 002016, initial value: 0016)
Capture 0 interrupt edge selection bits
b1 b0
0 0: Rising and falling edge
0 1: Rising edge
1 0: Falling edge
1 1: Not available
Capture 1 interrupt edge selection bits
b3 b2
0 0: Rising and falling edge
0 1: Rising edge
1 0: Falling edge
1 1: Not available
Capture 0 noise filter clock selection bits
b5 b4
0 0: Filter stop
0 1: f(XIN)
1 0: f(XIN)/8
1 1: f(XIN)/32
Capture 1 noise filter clock selection bits
b7 b6
0 0: Filter stop
0 1: f(XIN)
1 0: f(XIN)/8
1 1: f(XIN)/32
Fig. 44 Structure of capture software trigger register/capture
mode register
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 40 of 93
7546 Group
P00/CAP0
Trigger input channel 0
Capture latch 00
P10/CAP0
Timer A latch
Capture latch 01
Ring
/512
Timer A counter
Capture 0 timer source bit
Timer B counter
P30/CAP1 Capture channel 0
Ring
/512
Timer B latch
Capture channel 1
Fig. 45 Block diagram of input capture
Data bus
Capture register 0
read pointer
(001216, bit 4)
Capture register
Capture latch 00 (16)
Capture 0
status bit
(002216, bit 4)
Capture latch 01 (16)
Capture pointer
(001216, bits 4, 5)
Capture latch 00
software trigger bit
(001316, bit 0)
Rising
Capture 0
interrupt edge
selection bits
(002016, bits 0, 1)
Falling
Ring/512
Digital filter
P10/CAP0
P00/CAP0
Capture 0 input
port bits
(001E16, bits 0, 1)
Capture 0 noise
filter clock
selection bits
(002016, bits 4, 5)
Fig. 46 Block diagram of capture channel 0
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 41 of 93
Capture
trigger
Capture latch 0 (16)
Capture interrupt
Capture 0 timer
source bit
(001F16, bit 4)
Timer A counter (16)
Timer B counter (16)
7546 Group
Re-load the timer count value
Timer underflow
Capture input wave
Timer count value 000C 000B 000A 0009 0008 0007 0006 0005 0004 0003 0002 0001 0000 000F 000E 000D 000C 000B
Overwrite
Capture latch 00
XXXX
Capture latch 01
000A
0001
XXXX
000C
000F
0005
Capture interrupt
Capture x (x=0, 1) status bit
1
0
1
0
1
0
Fig. 47 Capture interrupt edge selection = “rising edge”
Re-load the timer count value
Timer underflow
Capture input wave
Timer count value 000C 000B 000A 0009 0008 0007 0006 0005 0004 0003 0002 0001 0000 000F 000E 000D 000C 000B
Overwrite
Capture latch 00
XXXX
000A
0001
XXXX
Capture latch 01
000C
000F
0005
Capture interrupt
Capture x (x=0, 1) status bit
1
0
Fig. 48 Capture interrupt edge selection = “rising and falling edge”
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 42 of 93
1
0
1
0
7546 Group
Serial Interface
(1) Clock Synchronous Serial I/O1 Mode
Clock synchronous serial I/O1 mode can be selected by setting
the serial I/O1 mode selection bit of the serial I/O1 control register
(bit 6) to “1”.
For clock synchronous serial I/O1, the transmitter and the receiver
must use the same clock. If an internal clock is used, transfer is
started by a write signal to the TB/RB.
The 7546 Group has Serial I/O1 and Serial I/O2. Except that Serial
I/O1 has the bus collision detection function and the TXD2 output
structure for Serial I/O2 is CMOS only, they have the same function.
●Serial I/O1
Serial I/O1 can be used as either clock synchronous or asynchronous (UART) serial I/O. A dedicated timer is also provided for
baud rate generation.
Data bus
Serial I/O1 control register
Address 001816
Receive buffer register 1
P10/RXD1/CAP0
Address 001A16
Receive buffer full flag (RBF)
Receive shift register 1
Receive interrupt request (RI)
Shift clock
Clock control circuit
P12/SCLK1
Serial I/O1 synchronous
clock selection bit
Frequency division ratio 1/(n+1)
BRG count source selection bit
XIN
Baud rate generator 1
Address 001C16
1/4
P13/SRDY1
F/F
1/4
Clock control circuit
Falling-edge detector
Shift clock
P11/TXD1
Transmit shift completion flag (TSC)
Transmit interrupt source selection bit
Transmit interrupt request (TI)
Transmit shift register 1
Transmit buffer register 1
Address 001816
Transmit buffer empty flag (TBE)
Serial I/O1 status register
Address 001916
Data bus
Fig. 49 Block diagram of clock synchronous serial I/O1
Transfer shift clock
(1/2 to 1/2048 of the internal
clock, or an external clock)
Serial output TxD1
D0
D1
D2
D3
D4
D5
D6
D7
Serial input RxD1
D0
D1
D2
D3
D4
D5
D6
D7
Receive enable signal SRDY1
Write pulse to receive/transmit
buffer register 1 (address 001816)
TBE = 0
TBE = 1
TSC = 0
RBF = 1
TSC = 1
Overrun error (OE)
detection
Notes 1: As the transmit interrupt (TI), which can be selected, either when the transmit buffer has emptied (TBE=1) or after
the transmit shift operation has ended (TSC=1), by setting the transmit interrupt source selection bit (TIC) of the
serial I/O1 control register.
2: If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial
data is output continuously from the TxD1 pin.
3: The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes “1” .
Fig. 50 Operation of clock synchronous serial I/O1 function
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 43 of 93
7546 Group
The transmit and receive shift registers each have a buffer, but the
two buffers have the same address in memory. Since the shift register cannot be written to or read from directly, transmit data is
written to the transmit buffer register, and receive data is read
from the receive buffer register.
The transmit buffer register can also hold the next data to be
transmitted, and the receive buffer register can hold a character
while the next character is being received.
(2) Asynchronous Serial I/O1 (UART) Mode
Clock asynchronous serial I/O mode (UART) can be selected by
clearing the serial I/O1 mode selection bit of the serial I/O1 control
register to “0”.
Eight serial data transfer formats can be selected, and the transfer
formats used by a transmitter and receiver must be identical.
Data bus
Address 001816
P10/RXD1/CAP0
Serial I/O1 control register Address 001A16
Receive buffer register 1
OE
Character length selection bit
ST detector
7 bits
Receive shift register 1
Receive buffer full flag (RBF)
Receive interrupt request (RI)
1/16
8 bits
PE FE
UART1 control register
Address 001B16
SP detector
Clock control circuit
Serial I/O1 synchronous clock selection bit
P12/SCLK1
XIN
BRG count source selection bit Frequency division ratio 1/(n+1)
Baud rate generator 1
Address 001C16
1/4
ST/SP/PA generator
Transmit shift completion flag (TSC)
1/16
P11/TXD1
Transmit interrupt source selection bit
Transmit interrupt request (TI)
Transmit shift register 1
Character length selection bit
Transmit buffer register 1
Address 001816
Transmit buffer empty flag (TBE)
Serial I/O1 status register Address 001916
Data bus
Fig. 51 Block diagram of UART serial I/O1
Transmit or receive clock
Transmit buffer 1
write signal
TBE=0
TSC=0
TBE=1
Serial output TXD1
TBE=0
TSC=1✽
TBE=1
ST
D0
D1
SP
ST
D0
✽
1 start bit
7 or 8 data bit
1 or 0 parity bit
1 or 2 stop bit (s)
Receive buffer 1
read signal
SP
D1
Generated at 2nd bit in 2-stop-bit mode
RBF=0
RBF=1
Serial input RXD1
ST
D0
D1
SP
RBF=1
ST
D0
D1
SP
Notes 1: Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception).
2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes “1,” can be selected to occur depending on the setting of the transmit
interrupt source selection bit (TIC) of the serial I/O1 control register.
3: The receive interrupt (RI) is set when the RBF flag becomes “1.”
4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle is necessary until changing to TSC=0.
Fig. 52 Operation of UART serial I/O1 function
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 44 of 93
7546 Group
[Transmit buffer register 1/receive buffer register 1 (TB1/
RB1)] 001816
The transmit buffer register and the receive buffer register are located at the same address. The transmit buffer is write-only and
the receive buffer is read-only. If a character bit length is 7 bits, the
MSB of data stored in the receive buffer is “0”.
[Serial I/O1 status register (SIO1STS)] 001916
The read-only serial I/O1 status register consists of seven flags
(bits 0 to 6) which indicate the operating status of the serial I/O1
function and various errors.
Three of the flags (bits 4 to 6) are valid only in UART mode.
The receive buffer full flag (bit 1) is cleared to “0” when the receive
buffer register is read.
If there is an error, it is detected at the same time that data is
transferred from the receive shift register to the receive buffer register, and the receive buffer full flag is set. A write to the serial I/O1
status register clears all the error flags OE, PE, FE, and SE (bit 3
to bit 6, respectively). Writing “0” to the serial I/O1 enable bit SIOE
(bit 7 of the serial I/O1 control register) also clears all the status
flags, including the error flags.
Bits 0 to 6 of the serial I/O1 status register are initialized to “0” at
reset, but if the transmit enable bit of the serial I/O1 control register has been set to “1”, the transmit shift completion flag (bit 2)
and the transmit buffer empty flag (bit 0) become “1”.
[Serial I/O1 control register (SIO1CON)] 001A16
The serial I/O1 control register consists of eight control bits for the
serial I/O1 function.
[UART1 control register (UART1CON)] 001B16
The UART1 control register consists of four control bits (bits 0 to
3) which are valid when asynchronous serial I/O is selected and
set the data format of an data transfer and one bit (bit 4) which is
always valid and sets the output structure of the P11/TxD1 pin.
[Baud rate generator 1 (BRG1)] 001C16
The baud rate generator determines the baud rate for serial transfer.
The baud rate generator divides the frequency of the count source
by 1/(n + 1), where n is the value written to the baud rate generator.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 45 of 93
■ Notes on Serial I/O1
• Serial I/O interrupt
When setting the transmit enable bit to “1”, the serial I/O transmit
interrupt request bit is automatically set to “1”. When not requiring
the interrupt occurrence synchronized with the transmission enabled, take the following sequence.
➀ Set the serial I/O transmit interrupt enable bit to “0” (disabled).
➁ Set the transmit enable bit to “1”.
➂ Set the serial I/O transmit interrupt request bit to “0” after 1 or
more instructions have been executed.
➃ Set the serial I/O transmit interrupt enable bit to “1” (enabled).
• I/O pin function when serial I/O1 is enabled.
The functions of P12 and P13 are switched with the setting values
of a serial I/O1 mode selection bit and a serial I/O1 synchronous
clock selection bit as follows.
(1) Serial I/O1 mode selection bit → “1” :
Clock synchronous type serial I/O is selected.
Setup of a serial I/O1 synchronous clock selection bit
“0” : P12 pin turns into an output pin of a synchronous clock.
“1” : P12 pin turns into an input pin of a synchronous clock.
Setup of a SRDY1 output enable bit (SRDY)
“0” : P13 pin can be used as a normal I/O pin.
“1” : P13 pin turns into a SRDY1 output pin.
(2) Serial I/O1 mode selection bit → “0” :
Clock asynchronous (UART) type serial I/O is selected.
Setup of a serial I/O1 synchronous clock selection bit
“0”: P12 pin can be used as a normal I/O pin.
“1”: P12 pin turns into an input pin of an external clock.
When clock asynchronous (UART) type serial I/O is selected, it is
P13 pin. It can be used as a normal I/O pin.
7546 Group
b7
b0
Serial I/O1 status register
(SIO1STS : address 001916, initial value: 8016)
Transmit buffer empty flag (TBE)
0: Buffer full
1: Buffer empty
Receive buffer full flag (RBF)
0: Buffer empty
1: Buffer full
Transmit shift completion flag (TSC)
0: Transmit shift in progress
1: Transmit shift completed
Overrun error flag (OE)
0: No error
1: Overrun error
Parity error flag (PE)
0: No error
1: Parity error
Framing error flag (FE)
0: No error
1: Framing error
Summing error flag (SE)
0: (OE) U (PE) U (FE)=0
1: (OE) U (PE) U (FE)=1
Not used (returns “1” when read)
b7
b0
Serial I/O1 control register
(SIO1CON : address 001A16, initial value: 0016)
BRG count source selection bit (CSS)
0: f(XIN)
1: f(XIN)/4
Serial I/O1 synchronous clock selection bit (SCS)
0: BRG output divided by 4 when clock synchronous
serial I/O is selected, BRG output divided by 16
when UART is selected.
1: External clock input when clock synchronous serial
I/O is selected, external clock input divided by 16
when UART is selected.
SRDY1 output enable bit (SRDY)
0: P13 pin operates as ordinary I/O pin
1: P13 pin operates as SRDY1 output pin
Transmit interrupt source selection bit (TIC)
0: Interrupt when transmit buffer has emptied
1: Interrupt when transmit shift operation is completed
Transmit enable bit (TE)
0: Transmit disabled
1: Transmit enabled
Receive enable bit (RE)
0: Receive disabled
1: Receive enabled
Serial I/O1 mode selection bit (SIOM)
0: Clock asynchronous (UART) serial I/O
1: Clock synchronous serial I/O
Serial I/O1 enable bit (SIOE)
0: Serial I/O1 disabled
(pins P10 to P13 operate as ordinary I/O pins)
1: Serial I/O1 enabled
(pins P10 to P13operate as serial I/O pins)
b7
b0
UART1 control register
(UART1CON : address 001B16, initial value: E016)
Character length selection bit (CHAS)
0: 8 bits
1: 7 bits
Parity enable bit (PARE)
0: Parity checking disabled
1: Parity checking enabled
Parity selection bit (PARS)
0: Even parity
1: Odd parity
Stop bit length selection bit (STPS)
0: 1 stop bit
1: 2 stop bits
P11/TXD1 P-channel output disable bit (POFF)
0: CMOS output (in output mode)
1: N-channel open drain output (in output mode)
Not used (return “1” when read)
Fig. 53 Structure of serial I/O1-related registers
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 46 of 93
7546 Group
Bus collision detection (SIO1)
b7
b0
Interrupt source set register
(INTSET: address 000A16, initial value: 0016)
SIO1 can detect a bus collision by setting UART1 bus collision detection interrupt enable bit.
When transmission is started in the clock synchronous or asynchronous (UART) serial I/O mode, the transmit pin TxD 1 is
compared with the receive pin RxD1 in synchronization with rising
edge of transmit shift clock. If they do not coincide with each other,
a bus collision detection interrupt request occurs.
When a transmit data collision is detected between LSB and MSB
of transmit data in the clock synchronous serial I/O mode or between the start bit and stop bit of transmit data in UART mode, a
bus collision detection can be performed by both the internal clock
and the external clock.
Key-on wakeup interrupt valid bit
UART1 bus collision detection
interrupt valid bit
A/D conversion interrupt valid bit
Timer 1 interrupt valid bit
Not used (returns “0” when read)
0: Interrupt invalid
1: Interrupt valid
b7
b0
Interrupt source discrimination register
(INTDIS: address 000B16, initial value: 0016)
Key-on wakeup interrupt discrimination bit
UART1 bus collision detection interrupt
discrimination bit
A/D conversion interrupt discrimination bit
Timer 1 interrupt discrimination bit
Not used (returns “0” when read)
A block diagram is shown in Fig. 55.
A timing diagram is shown in Fig. 56.
0: Interrupt does not occur
1: Interrupt occurs
b7
b0
Interrupt request register 1
(IREQ1 : address 003C16, initial value : 0016)
Note: Bus collision detection can be used when SIO1 is operating
at full-duplex communication. When SIO1 is operating at
half-duplex communication, set bus collision detection interrupt to be disabled.
Serial I/O1 receive interrupt request bit
Serial I/O1 transmit interrupt request bit
Serial I/O2 receive interrupt request bit
Serial I/O2 transmit interrupt request bit
INT0 interrupt request bit
INT1 interrupt request bit
Key-on wake up/UART1 bus collision
detection interrupt request bit
CNTR0 interrupt request bit
0 : No interrupt request issued
1 : Interrupt request issued
b7
b0
Interrupt control register 1
(ICON1 : address 003E16, initial value : 0016)
Serial I/O1 receive interrupt enable bit
Serial I/O1 transmit interrupt enable bit
Serial I/O2 receive interrupt enable bit
Serial I/O2 transmit interrupt enable bit
INT0 interrupt enable bit
INT1 interrupt enable bit
Key-on wake up/UART1 bus collision
detection interrupt enable bit
CNTR0 interrupt enable bit
0 : Interrupts disabled
1 : Interrupts enabled
Fig. 54 Bus collision detection circuit related registers
UART1 bus collision detection
interrupt discrimination bit
(Address 000B16, bit 1)
TxD1
RxD1
D
Q
Shift clock
Key-on wakeup/
UART1 bus collision detection
interrupt request bit
(Address 003C16, bit 6)
Key-on wakeup interrupt request
UART1 bus collision detection
interrupt valid bit
(Address 000A16, bit 1)
Fig. 55 Block diagram of bus collision detection interrupt circuit
Transmit shift clock
Bus collision detection
interrupt generation
Transmit pin TxD1
Receive pin RxD1
Data collision
Fig. 56 Timing diagram of bus collision detection interrupt
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 47 of 93
7546 Group
●Serial I/O2
(1) Clock Synchronous Serial I/O2 Mode
Clock synchronous serial I/O2 mode can be selected by setting
the serial I/O2 mode selection bit of the serial I/O2 control register
(bit 6) to “1”.
For clock synchronous serial I/O2, the transmitter and the receiver
must use the same clock. If an internal clock is used, transfer is
started by a write signal to the TB/RB.
Serial I/O2 can be used as either clock synchronous or asynchronous (UART) serial I/O. A dedicated timer is also provided for
baud rate generation.
Data bus
Serial I/O2 control register
Address 002E16
Receive buffer register 2
Receive buffer full flag (RBF)
Receive shift register 2
P04/RXD2
Shift clock
Address 003016
Receive interrupt request (RI)
Clock control circuit
P06/SCLK2
XIN
Serial I/O2 synchronous
clock selection bit
Frequency division ratio 1/(n+1)
BRG count source selection bit
Baud rate generator 2
Address 003216
1/4
P07/SRDY2
Clock control circuit
Falling-edge detector
F/F
P05/TXD2
1/4
Shift clock
Transmit shift completion flag (TSC)
Transmit shift register 2
Transmit interrupt source selection bit
Transmit interrupt request (TI)
Transmit buffer register 2
Address 002E16
Transmit buffer empty flag (TBE)
Serial I/O2 status register
Address 002F16
Data bus
Fig. 57 Block diagram of clock synchronous serial I/O2
Transfer shift clock
(1/2 to 1/2048 of the internal
clock, or an external clock)
Serial output TxD2
D0
D1
D2
D3
D4
D5
D6
D7
Serial input RxD2
D0
D1
D2
D3
D4
D5
D6
D7
Receive enable signal SRDY2
Write pulse to receive/transmit
buffer register 2 (address 002E16)
TBE = 0
TBE = 1
TSC = 0
RBF = 1
TSC = 1
Overrun error (OE)
detection
Notes 1: As the transmit interrupt (TI), which can be selected, either when the transmit buffer has emptied (TBE=1) or after
the transmit shift operation has ended (TSC=1), by setting the transmit interrupt source selection bit (TIC) of the
serial I/O2 control register.
2: If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial
data is output continuously from the TxD2 pin.
3: The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes “1” .
Fig. 58 Operation of clock synchronous serial I/O2 function
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 48 of 93
7546 Group
The transmit and receive shift registers each have a buffer, but the
two buffers have the same address in memory. Since the shift register cannot be written to or read from directly, transmit data is
written to the transmit buffer register, and receive data is read
from the receive buffer register.
The transmit buffer register can also hold the next data to be
transmitted, and the receive buffer register can hold a character
while the next character is being received.
(2) Asynchronous Serial I/O2 (UART) Mode
Clock asynchronous serial I/O mode (UART) can be selected by
clearing the serial I/O2 mode selection bit of the serial I/O2 control
register to “0”.
Eight serial data transfer formats can be selected, and the transfer
formats used by a transmitter and receiver must be identical.
Data bus
Address 002E16
P04/RXD2
Serial I/O2 control register Address 003016
Receive buffer full flag (RBF)
Receive interrupt request (RI)
Receive buffer register 2
OE
Character length selection bit
ST detector
7 bits
Receive shift register 2
1/16
8 bits
PE FE
UART2 control register
SP detector
Address 003116
Clock control circuit
Serial I/O2 synchronous clock selection bit
P06/SCLK2
XIN
BRG count source selection bit Frequency division ratio 1/(n+1)
Baud rate generator 2
Address 003216
1/4
ST/SP/PA generator
Transmit shift completion flag (TSC)
1/16
P05/TXD2
Transmit interrupt source selection bit
Transmit interrupt request (TI)
Transmit shift register 2
Character length selection bit
Transmit buffer register 2
Address 002E16
Transmit buffer empty flag (TBE)
Serial I/O2 status register Address 002F16
Data bus
Fig. 59 Block diagram of UART serial I/O2
Transmit or receive clock
Transmit buffer 2
write signal
TBE=0
TSC=0
TBE=1
Serial output TXD2
TBE=0
TSC=1✽
TBE=1
ST
D0
D1
SP
ST
D0
Receive buffer 2
read signal
SP
D1
✽
1 start bit
7 or 8 data bit
1 or 0 parity bit
1 or 2 stop bit (s)
Generated at 2nd bit in 2-stop-bit mode
RBF=0
RBF=1
Serial input RXD2
ST
D0
D1
SP
RBF=1
ST
D0
D1
SP
Notes 1: Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception).
2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes “1,” can be selected to occur depending on the setting of the transmit
interrupt source selection bit (TIC) of the serial I/O2 control register.
3: The receive interrupt (RI) is set when the RBF flag becomes “1.”
4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle is necessary until changing to TSC=0.
Fig. 60 Operation of UART serial I/O2 function
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 49 of 93
7546 Group
[Transmit buffer register 2/receive buffer register 2 (TB2/
RB2)] 002E16
The transmit buffer register and the receive buffer register are located at the same address. The transmit buffer is write-only and
the receive buffer is read-only. If a character bit length is 7 bits, the
MSB of data stored in the receive buffer is “0”.
[Serial I/O2 status register (SIO2STS)] 002F16
The read-only serial I/O2 status register consists of seven flags
(bits 0 to 6) which indicate the operating status of the serial I/O2
function and various errors.
Three of the flags (bits 4 to 6) are valid only in UART mode.
The receive buffer full flag (bit 1) is cleared to “0” when the receive
buffer register is read.
If there is an error, it is detected at the same time that data is
transferred from the receive shift register to the receive buffer register, and the receive buffer full flag is set. A write to the serial I/O1
status register clears all the error flags OE, PE, FE, and SE (bit 3
to bit 6, respectively). Writing “0” to the serial I/O2 enable bit SIOE
(bit 7 of the serial I/O2 control register) also clears all the status
flags, including the error flags.
Bits 0 to 6 of the serial I/O2 status register are initialized to “0” at
reset, but if the transmit enable bit of the serial I/O2 control register has been set to “1”, the transmit shift completion flag (bit 2)
and the transmit buffer empty flag (bit 0) become “1”.
[Serial I/O2 control register (SIO2CON)] 003016
The serial I/O2 control register consists of eight control bits for the
serial I/O2 function.
[UART2 control register (UART2CON)] 003116
The UART control register consists of four control bits (bits 0 to 3)
which are valid when asynchronous serial I/O is selected and set
the data format of an data transfer.
[Baud rate generator 2 (BRG2)] 003216
The baud rate generator determines the baud rate for serial transfer.
The baud rate generator divides the frequency of the count source
by 1/(n + 1), where n is the value written to the baud rate generator.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 50 of 93
■ Notes on Serial I/O2
• Serial I/O interrupt
When setting the transmit enable bit to “1”, the serial I/O transmit
interrupt request bit is automatically set to “1”. When not requiring
the interrupt occurrence synchronized with the transmission enabled, take the following sequence.
➀ Set the serial I/O transmit interrupt enable bit to “0” (disabled).
➁ Set the transmit enable bit to “1”.
➂ Set the serial I/O transmit interrupt request bit to “0” after 1 or
more instructions have been executed.
➄ Set the serial I/O transmit interrupt enable bit to “1” (enabled).
• I/O pin function when serial I/O2 is enabled.
The functions of P06 and P07 are switched with the setting values
of a serial I/O2 mode selection bit and a serial I/O2 synchronous
clock selection bit as follows.
(1) Serial I/O2 mode selection bit → “1” :
Clock synchronous type serial I/O is selected.
Setup of a serial I/O2 synchronous clock selection bit
“0” : P06 pin turns into an output pin of a synchronous clock.
“1” : P06 pin turns into an input pin of a synchronous clock.
Setup of a SRDY2 output enable bit (SRDY)
“0” : P07 pin can be used as a normal I/O pin.
“1” : P07 pin turns into a SRDY2 output pin.
(2) Serial I/O2 mode selection bit → “0” :
Clock asynchronous (UART) type serial I/O is selected.
Setup of a serial I/O2 synchronous clock selection bit
“0”: P06 pin can be used as a normal I/O pin.
“1”: P06 pin turns into an input pin of an external clock.
When clock asynchronous (UART) type serial I/O is selected, it is
P07 pin. It can be used as a normal I/O pin.
7546 Group
b7
b0
Serial I/O2 status register
(SIO2STS : address 002F16, initial value: 8016)
Transmit buffer empty flag (TBE)
0: Buffer full
1: Buffer empty
Receive buffer full flag (RBF)
0: Buffer empty
1: Buffer full
Transmit shift completion flag (TSC)
0: Transmit shift in progress
1: Transmit shift completed
Overrun error flag (OE)
0: No error
1: Overrun error
Parity error flag (PE)
0: No error
1: Parity error
Framing error flag (FE)
0: No error
1: Framing error
Summing error flag (SE)
0: (OE) U (PE) U (FE)=0
1: (OE) U (PE) U (FE)=1
Not used (returns “1” when read)
b7
b0
Serial I/O2 control register
(SIO2CON : address 003016, initial value: 0016)
BRG count source selection bit (CSS)
0: f(XIN)
1: f(XIN)/4
Serial I/O2 synchronous clock selection bit (SCS)
0: BRG output divided by 4 when clock synchronous
serial I/O is selected, BRG output divided by 16
when UART is selected.
1: External clock input when clock synchronous serial
I/O is selected, external clock input divided by 16
when UART is selected.
SRDY2 output enable bit (SRDY)
0: P07 pin operates as ordinary I/O pin
1: P07 pin operates as SRDY2 output pin
Transmit interrupt source selection bit (TIC)
0: Interrupt when transmit buffer has emptied
1: Interrupt when transmit shift operation is completed
Transmit enable bit (TE)
0: Transmit disabled
1: Transmit enabled
Receive enable bit (RE)
0: Receive disabled
1: Receive enabled
Serial I/O2 mode selection bit (SIOM)
0: Clock asynchronous (UART) serial I/O
1: Clock synchronous serial I/O
Serial I/O2 enable bit (SIOE)
0: Serial I/O2 disabled
(pins P04 to P07 operate as ordinary I/O pins)
1: Serial I/O2 enabled
(pins P04 to P07 operate as serial I/O pins)
b7
b0
UART2 control register
(UART2CON : address 003116, initial value: E016)
Character length selection bit (CHAS)
0: 8 bits
1: 7 bits
Parity enable bit (PARE)
0: Parity checking disabled
1: Parity checking enabled
Parity selection bit (PARS)
0: Even parity
1: Odd parity
Stop bit length selection bit (STPS)
0: 1 stop bit
1: 2 stop bits
Not used (return “0” when read)
(Do not write “1” to this bit.)
Not used (return “1” when read)
Fig. 61 Structure of serial I/O2-related registers
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 51 of 93
7546 Group
A/D Converter
The functional blocks of the A/D converter are described below.
b7
b0
A/D control register
(ADCON : address 003416, initial value: 1016)
[A/D conversion register] AD
The A/D conversion register is a read-only register that stores the
result of A/D conversion. Do not read out this register during an A/
D conversion.
[A/D control register] ADCON
The A/D control register controls the A/D converter.
Bit 2 to 0 are analog input pin selection bits.
Bit 3 is the A/D conversion clock selection bit. When “0” is set to this
bit, the A/D conversion clock is f(XIN)/2 and the A/D conversion time
is 122 cycles of f(XIN). When “1” is set to this bit, the A/D conversion
clock is f(XIN) and the A/D conversion time is 61 cycles of f(X IN).
Bit 4 is the A/D conversion completion bit. The value of this bit remains at “0” during A/D conversion, and changes to “1” at
completion of A/D conversion.
A/D conversion is started by setting this bit to “0”.
[Comparison voltage generator]
The comparison voltage generator divides the voltage between
AVSS and VREF by 1024, and outputs the divided voltages.
[Channel selector]
The channel selector selects one of ports P25/AN5 to P2 0/AN0 ,
and inputs the voltage to the comparator.
Analog input pin selection bits
000 : P20/AN0
001 : P21/AN1
010 : P22/AN2
011 : P23/AN3
100 : P24/AN4
101 : P25/AN5
110 : Not available
111 : Not available
A/D conversion clock selection bit (Note 1)
0 : f(XIN)/2
1 : f(XIN)
A/D conversion completion bit
0 : Conversion in progress
1 : Conversion completed
Not used (returns “0” when read)
Notes 1: A/D conversion clock=f(XIN) can be used only
when ceramic oscillation or on-chip oscillator is used.
Select f(XIN)/2 when RC oscillation is used.
Fig. 62 Structure of A/D control register
Read 8-bit (Read only address 003516)
b7
(Address 003516)
b9 b8
b7
b0
b6
b5
b4
Read 10-bit (read in order address 003616, 003516)
b7
b9
■ Notes on A/D converter
As for AD translation accuracy, on the following operating conditions, accuracy may become low.
(1) Since the analog circuit inside a microcomputer becomes sensitive to noise when V REF voltage is set up lower than Vcc
voltage, accuracy may become low rather than the case
where VREF voltage and Vcc voltage are set up to the same
value..
(2) When VREF voltage is lower than [ 3.0 V ], the accuracy at the
low temperature may become extremely low compared with
that at room temperature. When the system would be used at
low temperature, the use at VREF=3.0 V or more is recommended.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 52 of 93
b7
(Address 003516)
b7 b6
b2
b0
(Address 003616)
[Comparator and control circuit]
The comparator and control circuit compares an analog input voltage with the comparison voltage and stores its result into the A/D
conversion register. When A/D conversion is completed, the control circuit sets the A/D conversion completion bit and the A/D
interrupt request bit to “1”. Because the comparator is constructed
linked to a capacitor, set f(XIN) in order that the A/D conversion
clock is 250 kHz or over during A/D conversion.
b3
b8
b0
b5
b4
b3
b2
b1
b0
Note: High-order 6-bit of address 003616 returns “0” when read.
Fig. 63 Structure of A/D conversion register
7546 Group
Data bus
b7
b0
A/D control register
(Address 003416)
3
A/D interrupt request
Channel selector
A/D control circuit
P20/AN0
P21/AN1
P22/AN2
P23/AN3
P24/AN4
P25/AN5
Comparator
A/D conversion register (high-order)
(Address 003616)
A/D conversion register (low-order)
(Address 003516)
10
Resistor ladder
f(XIN)
f(XIN)/2
VREF
Fig. 64 Block diagram of A/D converter
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 53 of 93
VSS
7546 Group
Watchdog Timer
The watchdog timer gives a means for returning to a reset status
when the program fails to run on its normal loop due to a runaway.
The watchdog timer consists of an 8-bit watchdog timer H and an
8-bit watchdog timer L, being a 16-bit counter.
● Standard operation of watchdog timer
(1) Start of watchdog timer
The watchdog timer starts operating by setting value of the function set ROM data 2 (FSROM2: address 0FFA16) or writing to the
watchdog timer control register (WDTCON: address 003916).
Set “0” to the watchdog timer start selection bit (bit 1 of FSROM2)
when operation starts by setting value of FSROM2. In this case,
the watchdog timer starts operating after releasing reset.
Write an arbitrary value to WDTCON when FSROM2 is set to be
invalid and operation starts by program. Operation by program
can start even when “1” (stop state after releasing reset) is set to
the watchdog timer start selection bit.
(2) Operation of watchdog timer
Watchdog timer L is set to “FF16”and watchdog timer H is set to
“FF16” by reset or writing an arbitrary value to WDTCON.
When the watchdog timer starts operating, the selected clock is
counted and internal reset occurs by the watchdog timer H underflow.
Accordingly, write to WDTCON before underflow by program.
When WDTCON is read, the values of the STP instruction function
selection bit, watchdog timer H count source selection bit and the
high-order 6 bits of the watchdog timer H are read.
(3) Count source clock of watchdog timer
The count source clock of the watchdog timer can be selected by
the watchdog timer source clock selection bit (bit 0 of FSROM2).
If “0” is set to the watchdog timer source clock selection bit, the
count source clock of the watchdog timer always is the on-chip oscillator output/16.
It changes by setting the clock division ratio selection bits (bit 7
and bit 6 of the CPU mode register) when “1” is set to the watchdog timer source clock selection bit or FSROM2 is set to be
invalid.
When a double-speed mode, a high-speed mode, and a middlespeed mode are selected by the clock division ratio selection bits,
the count source clock of the watchdog timer becomes f(XIN)/16.
When the supply from on-chip oscillator is selected, it becomes
the on-chip oscillator output/16.
(4) Watchdog timer H count source selection bit
The count source of watchdog timer H can be selected by
FSROM2 or program.
When “0” is set to watchdog timer H count source selection bit (bit
2 of FSROM2), the watchdog timer L underflow signal is selected
as the count source of watchdog timer H and the detection time is
131.072 ms at f(XIN) = 8 MHz.
When “1” is set to this bit, the clock selected as the count source
of watchdog timer L is input to watchdog timer H. In this case, the
detection time is 512 µs at f(XIN) =8 MHz.
When FSROM2 is set to be invalid, the count source of watchdog
timer can be set by watchdog timer H count source selection bit
(bit 7 of WDTCON).
When “0” is set to this bit, the watchdog timer L underflow signal is
selected as the count source of watchdog timer H.
When “1” is set to this bit, the clock selected as the count source
of watchdog timer L is input to watchdog timer H.
This bit is cleared to “0” after reset.
(5) STP instruction function selection bit
The function of the STP instruction can be selected by FSROM2
or program.
When “0” is set to the STP instruction function selection bit (bit 3
of FSROM2), system enters into the stop mode at the STP instruction execution.
When “1” is set to this bit, internal reset occurs at the STP instruction execution. When the function of the STP instruction is set by
FSROM2, it cannot be changed by program.
When setting value of FSROM2 is invalid, the function of the STP
instruction can be set by the STP instruction function selection bit
(bit 6 of WDTCON).
When “0” is set to this bit, system enters into the stop mode at the
STP instruction execution.
When “1” is set to this bit, internal reset occurs at the STP instruction execution.
Once this bit is set to “1”, it cannot be changed to “0” by program.
This bit is cleared to “0” after reset.
■ Notes on watchdog timer
1. The watchdog timer is operating during the wait mode. Write
data to the watchdog timer control register to prevent timer underflow.
2. The watchdog timer stops during the stop mode. However, the
watchdog timer is running during the oscillation stabilizing time
after the STP instruction is released. In order to avoid the underflow of the watchdog timer, the watchdog timer count source
selection bit (bit 7 of watchdog timer control register (address
3916)) before executing the STP instruction.
3. The STP instruction function selection bit (bit 6 of watchdog
timer control register (address 3916)) can be rewritten only once
after releasing reset. After rewriting it is disable to write any data
to this bit.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 54 of 93
7546 Group
Watchdog timer H count source
selection bit (bit 2 of FSROM2)
or bit 7 of WDTCON
Source clock selection
(auto-switch depending on setting of CPUM)
Watchdog timer L (8)
XIN clock
On-chip oscillator
Count start
(Watchdotm timer start selection bit
(bit 1 of FSROM2))
or writing arbitrary value to WDTCON
Data bus
Write “FF16” to
WDTCON
On-chip oscillator output can be
fixed by bit 0 of FSROM2
1/16
Write "FF16" to
WDTCON
“0”
Watchdog timer H (8)
“1”
STP instruction function selection bit
(bit 3 of FSROM2)
Bit 6 of WDTCON
STP Instruction
Reset pin input
Reset
circuit
Internal reset
FSROM2: Function set ROM data 2
WDTCON: Watchdog timer control register
CPUM: CPU mode register
Fig. 65 Block diagram of watchdog timer
b7
b0
Watchdog timer control register (Note 1)
(WDTCON: address 003916, initial value: 3F16)
Control by Function set ROM data 2
(FSROM2: address FFDA16) (Note 2)
Watchdog timer H (read only for high-order 6-bit)
This cannot be controlled by FSROM2.
STP instruction function selection bit
(Note 1, Note 3)
0 : System enters into the stop mode
at the STP instruction execution
1 : Internal reset occurs at the STP instruction execution
Watchdog timer H count source selection bit
(Note 1, Note 4)
0 : Watchdog timer L underflow
1 : On-chip oscillator/16 or f(XIN)/16
This bit function can be set by setting bit 3 of FSROM2.
Bit 3 of FSROM2 = 0: Bit 6 of WDTCON is fixed to “0”.
Bit 3 of FSROM2 = 1: Bit 6 of WDTCON is fixed to “1”.
The initial value of this bit is changed by setting bit 2 of
FSROM2.
Bit 2 of FSROM2 = 0:
Initial value of bit 7 of WDTCON is changed to “0”.
Bit 2 of FSROM2 = 1:
Initial value of bit 7 of WDTCON is changed to “1”.
The following setting can be available by setting bit 0 of FSROM2.
(This setting cannot be set by WDTCON)
Bit 0 of FSROM2 = 0: The source clock of watchdog timer is always
the on-chip oscillator output/16.
Bit 0 of FSROM2 = 1: The source clock of watchdog timer is the
on-chip oscillator output/16 of f(XIN)/16.
Notes 1: When the setting by the function set ROM data 2 (FSROM2) is performed, the initial value of CPUM is changed
after releasing reset since bits 6 and 7 of WDTCON are fixed.
2: The setting values of FSROM2 become valid by setting “0” to bit 0 of function set ROM data 0 (FSROM0).
The setting values of FSROM2 are invalid by setting “1” to this bit.
3:The setting value of this bit can be fixed after releasing reset by FSROM2, and then, the setting value cannot be changed by program.
Also, when the setting by program is performed, this bit can be rewritten only once after releasing reset.
After rewriting it is disable to write any data to this bit.
4: When FSROM2 is used to select the watchdog timer H count source, the initial value of this bit is changed after releasing reset.
Fig. 66 Structure of watchdog timer control register
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 55 of 93
7546 Group
Power-on Reset Circuit
Reset can be automatically performed at power on (power-on reset) by the built-in power-on reset circuit.
In order to use the power-on reset circuit effectively, the time for
the supply voltage to rise from 0 V to 1.8 V must be set to 1 ms or
less.
____________
When the built-in power-on reset circuit is used, pull-up the RESET
pin to VCC.
1 ms or les s
VCC (Note)
Power-on reset
circuit output
Low Voltage Detection Circuit
Internal reset signal
The built-in low voltage detection circuit is designed to detect a
drop in voltage and to reset the microcomputer if the power source
voltage drops below a set value (Typ.1.90 V).
The low voltage detection circuit is valid by setting “1” to bit 1 of
the function set ROM data 0.
Also, when “1” is set to bit 3 of the function set ROM data 0, the
low voltage detection circuit can be valid even in the stop mode.
The low voltage detection circuit is stopped in the stop mode by
setting “0” to this bit, so that the power dissipation is reduced.
Reset
state
Power-on
Reset released
Note: Keep the value of supply voltage to the minimum value
or more of the recommended operating conditions.
Fig. 67 Operation waveform diagram of power-on reset circuit
VCC
Reset voltage (Typ:1.90V)
Microcomputer starts operation
by the built-in on-chip oscillator.
Internal reset signal
Fig. 68 Operation waveform diagram of low voltage detection circuit
On-chip oscillator
clock RING
Internal CPU clock φ
RESET
Internal reset signal
SYNC
?
Address
Data
?
?
9 to 16 cycles of
internal CPU clock φ
Fig. 69 Timing diagram at reset
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 56 of 93
?
?
?
?
?
?
FFFC
?
FFFD
ADL
ADH,ADL
ADH
Reset address from the
vector table
7546 Group
Address
(1) Port P0 direction register (P0D)
Register contents
0016
000116
X
X
X
0
0
(2) Port P1 direction register (P1D)
000316
(3) Port P2 direction register (P2D)
000516
0016
(4) Port P3 direction register (P3D)
000716
0016
(5) Interrupt source set register (INTSET)
000A16
0016
(6) Interrupt source discrimination register (INTDIS)
000B16
0016
(7) Compare register (low-order) (CMPL)
001016
0016
(8) Compare register (high-order) (CMPH)
(9) Capture/Compare register R/W pointer (CCRP)
001116
0016
001216
0016
(10) Capture software trigger register (CSTR)
001316
0016
(11) Compare register re-load register (CMPR)
001416
0016
(12) Port P0P3 drive capacity control register (DCCR)
001516
0016
0016
(13) Pull-up control register (PULL)
001616
(14) Port P1P3 control register (P1P3C)
001716
(15) Serial I/O1 status register (SIO1STS)
001916
(16) Serial I/O1 control register (SIO1CON)
001A16
(17) UART1 control register (UART1CON)
001B16
0
0
0
0
0
0
0
0
0
0
0
0016
1
0
0
0
0
0016
1
1
1
0
0
(18) Timer A, B mode register (TABM)
001D16
0016
(19) Capture/Compare port register (CCPR)
001E16
0016
(20) Timer source selection register (TMSR)
001F16
0016
(21) Capture mode register (CAPM)
002016
0016
(22) Compare output mode register (CMOM)
002116
0016
(23) Capture/Compare status register (CCSR)
002216
0016
(24) Compare interrupt source register (CISR)
002316
002416
0016
(25) Timer A (low-order) (TAL)
(26) Timer A (high-order) (TAH)
002516
FF16
(27) Timer B (low-order) (TBL)
002616
FF16
(28) Timer B (high-order) (TBH)
002716
FF16
FF16
002816
FF16
(30) Timer 1 (T1)
002916
0116
(31) Timer count source set register (TCSS)
002A16
0016
(32) Timer X mode register (TXM)
002B16
0016
(33) Prescaler X (PREX)
002C16
FF16
(34) Timer X (TX)
002D16
(35) Serial I/O2 control register (SIO2STS)
002F16
(36) Serial I/O2 register (SIO2CON)
003016
(29) Prescaler 1 (PRE1)
0
FF16
1
0
0
0
0
0016
(37) UART2 control register (UART2CON)
003116
1
1
1
0
0
0
0
0
(38) A/D control register (ADCON)
003416
0
0
0
1
0
0
0
0
(39) On-chip oscillation division ratio selection register (RODR) 003716
003816
(40) MISRG
0
0
0
0
0
0
1
0
(41) Watchdog timer control register (WDTCON) (Note 3)
003916
0
1
1
1
(42) Interrupt edge selection register (INTEDGE)
003A16
(43) CPU mode register (CPUM) (Note 3)
003B16
0
0
0
(44) Interrupt request register 1 (IREQ1)
003C16
0016
(45) Interrupt request register 2 (IREQ2)
003D16
0016
(46) Interrupt control register 1 (ICON1)
003E16
0016
(47) Interrupt control register 2 (ICON2)
003F16
1
X
X
(48) Processor status register
(49) Program counter
(50) Watchdog timer H
(51) Watchdog timer L
(PS)
(PCH)
(PCL)
0016
0
1
1
1
0
0
0
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 57 of 93
0
0016
X
X
X
X
X
Contents of address FFFD16
Contents of address FFFC16
FF16
FF16
Notes 1: X : Undefined
2: The content of other registers is undefined when the microcomputer is reset.
The initial values must be surely set before you use it.
3: When the setting by the function set ROM data 2 (FSROM2) is performed,
the initial values of these registers at reset are changed.
Fig. 69 Internal status of microcomputer at reset
1
0016
7546 Group
Clock Generating Circuit
An oscillation circuit can be formed by connecting a resonator between XIN and XOUT, and an RC oscillation circuit can be formed
by connecting a resistor and a capacitor.
Use the circuit constants in accordance with the resonator
manufacturer's recommended values.
No external resistor is needed between X IN and XOUT since a
feed-back resistor exists on-chip. (An external feed-back resistor
may be needed depending on conditions.)
(1) On-chip oscillator operation
When the MCU operates by the on-chip oscillator for the main
clock, connect XIN pin to VCC through a resistor and leave XOUT
pin open.
The clock frequency of the on-chip oscillator depends on the supply voltage and the operation temperature range.
Be careful that variable frequencies when designing application
products.
M37546
XI N
R
Note: The clock frequency of the
on-chip oscillator depends
on the supply voltage and
the operation temperature
range.
XOUT
Be careful that variable
frequencies and obtain
Open
the sufficient margin.
Fig. 70 Processing of XIN and XOUT pins at on-chip oscillator
operation
M37546
XIN
XOUT
Rd
(2) Ceramic resonator
When the ceramic resonator is used for the main clock, connect
the ceramic resonator and the external circuit to pins XIN and
XOUT at the shortest distance. A feedback resistor is built in between pins XIN and XOUT.
(3) RC oscillation
When the RC oscillation is used for the main clock, connect the
XIN pin and XOUT pin to the external circuit of resistor R and the
capacitor C at the shortest distance.
The frequency is affected by a capacitor, a resistor and a microcomputer.
So, set the constants within the range of the frequency limits.
(4) External clock
When the external signal clock is used for the main clock, connect
the XIN pin to the clock source and leave XOUT pin open.
Select “0” (ceramic oscillation) to oscillation mode selection bit of
CPU mode register (003B16).
COUT
CI N
Note: Insert a damping resistor if required.
The resistance will vary depending on the oscillator and
the oscillation drive capacity setting.
Use the value recommended by the maker of the oscillator.
Also, if the oscillator manufacturer’s data sheet specifies
that a feedback resistor be added external to the chip
though a feedback resistor exists on-chip, insert a feedback resistor between X IN and X OUT following the
instruction.
Fig. 71 External circuit of ceramic resonator
Note: Connect the external
M37546
XIN
XOUT
circuit of resistor R
and the capacitor C at
the shortest distance.
The frequency is affected by a capacitor,
R a resistor and a microcomputer.
C So, set the constants
within the range of the
frequency limits.
Fig. 72 External circuit of RC oscillation
M37546
XIN
External oscillation
circuit
VCC
VSS
Fig. 73 External clock input circuit
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 58 of 93
XOUT
Open
7546 Group
(1) Oscillation control
• Stop mode
When the STP instruction is executed, the internal clock φ stops at
an “H” level and the XIN oscillator stops. At this time, timer 1 is set
to “0116” and prescaler 1 is set to “FF16” when the oscillation stabilization time set bit after release of the STP instruction is “0”. On
the other hand, timer 1 and prescaler 1 are not set when the
above bit is “1”. Accordingly, set the wait time fit for the oscillation
stabilization time of the oscillator to be used. f(XIN)/16 is forcibly
connected to the input of prescaler 1. When an external interrupt
is accepted, oscillation is restarted but the internal clock φ remains
at “H” until timer 1 underflows. As soon as timer 1 underflows, the
internal clock φ is supplied. This is because when a ceramic oscillator is used, some time is required until a start of oscillation. In
case oscillation is restarted by reset, no wait time is generated. So
apply an “L” level to the RESET pin while oscillation becomes
stable, or set the wait time by on-chip oscillator operation after
system is released from reset until the oscillation is stabled.
• Wait mode
If the WIT instruction is executed, the internal clock φ stops at an
“H” level, but the oscillator does not stop. The internal clock restarts if a reset occurs or when an interrupt is received. Since the
oscillator does not stop, normal operation can be started immediately after the clock is restarted. To ensure that interrupts will be
received to release the STP or WIT state, interrupt enable bits
must be set to “1” before the STP or WIT instruction is executed.
b7
■ Notes on Clock Generating Circuit
For use with the oscillation stabilization set bit after release of the
STP instruction set to “1”, set values in timer 1 and prescaler 1 after fully appreciating the oscillation stabilization time of the
oscillator to be used.
• Switch of ceramic and RC oscillations
After releasing reset the operation starts by starting an on-chip oscillator. Then, a ceramic oscillation or an RC oscillation is selected
by setting bit 5 of the CPU mode register.
• Double-speed mode
When a ceramic oscillation is selected, a double-speed mode can
be used. Do not use it when an RC oscillation is selected.
• CPU mode register
Bits 5, 1 and 0 of CPU mode register are used to select oscillation
mode and to control operation modes of the microcomputer. In order to prevent the dead-lock by error-writing (ex. program
run-away), these bits can be rewritten only once after releasing reset. After rewriting it is disable to write any data to the bit. (The
emulator MCU “M37542RSS” is excluded.)
Also, when the read-modify-write instructions (SEB, CLB) are executed to bits 2 to 4, 6 and 7, bits 5, 1 and 0 are locked.
b0
CPU mode register (Note 1)
(CPUM: address 003B16, initial value: 8016)
Processor mode bits
b1 b0
0 0 Single-chip mode
0 1 Not available
1 0 Not available
1 1 Not available
Stack page selection bit
0 : 0 page
1 : 1 page
Control by Function set ROM data 2
(FSROM2: address FFDA16) (Note 2)
This cannot be controlled by FSROM2.
This cannot be controlled by FSROM2.
On-chip oscillator oscillation control bit (Note 3)
0 : On-chip oscillator oscillation enabled
1 : On-chip oscillator oscillation stop
This bit function can be set by setting bit 4 of FSROM2. (Note 3)
Bit 4 of FSROM2 = 0: Bit 3 of CPUM is fixed to “0”.
Bit 4 of FSROM2 = 1: Bit 3 of CPUM is “0” or “1”.
XIN oscillation control bit
0 : Ceramic or RC oscillation enabled
1 : Ceramic or RC oscillation stop
This cannot be controlled by FSROM2.
This bit function can be set by setting bit 5 of FSROM2. (Note 4)
Oscillation mode selection bit (Note 1, Note 4)
Bit 5 of FSROM2 = 0: Bit 5 of CPUM is fixed to “0”.
0 : Ceramic oscillation
Bit 5 of FSROM2 = 1: Bit 5 of CPUM is “0” or “1”.
1 : RC oscillation
Clock division ratio selection bits
This cannot be controlled by FSROM2.
b7 b6
0 0 : f(φ) = f(XIN)/2 (High-speed mode)
0 1 : f(φ) = f(XIN)/8 (Middle-speed mode)
1 0 : applied from on-chip oscillator
1 1 : f(φ) = f(XIN)/1 (Double-speed mode)(Note 5)
Note 1: When the setting by the function set ROM data 2 (FSROM2) is performed, the initial value of CPUM is changed
after releasing reset since bit 5 of CPUM is fixed.
2: The setting values of FSROM2 become valid by setting “0” to bit 0 of function set ROM data 0 (FSROM0).
The setting values of FSROM2 are invalid by setting “1” to this bit.
(In order that FSROM2 is invalid, write to CPUM after releasing reset.)
3: When bit 4 of FSROM2 is set to “0”, the operation of on-chip oscillator cannot be stopped.
Since the on-chip oscillator is not stopped also in the stop mode, the dissipation current in the stop mode is increased.
4: The setting value of bit 5 of CPUM can be fixed after releasing reset by setting value of bit 5 of FSROM2.
Also, when the setting of FSROM2 is invalid, this bit can be rewritten only once after releasing reset.
After rewriting it is disable to write any data to this bit.
This bit is initialized by reset, and then, rewriting it is enabled.
5: This setting can be used only at ceramic oscillation. Do not use this at RC oscillation.
Fig. 74 Structure of CPU mode register
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 59 of 93
7546 Group
• Clock division ratio, XIN oscillation control, on-chip oscillator control
The state transition shown in Fig. 78 can be performed by setting
the clock division ratio selection bits (bits 7 and 6), XIN oscillation
control bit (bit 4), on-chip oscillator oscillation control bit (bit 3) of
CPU mode register. Be careful of notes on use in Fig. 78.
• Count source (Timer 1, Timer A, Timer B, Timer X, Serial I/O, Serial
I/O2, A/D converter, Watchdog timer)
The count sources of these functions are affected by the clock division selection bit of the CPU mode register.
The f(XIN) clock is supplied to the watchdog timer when selecting
f(XIN) as the CPU clock.
The on-chip oscillator output is supplied to these functions when selecting the on-chip oscillator output as the CPU clock.
However, the watchdog timer is also affected by the function set
ROM.
● On-chip oscillation division ratio
At on-chip oscillator mode, division ratio of on-chip oscillator for
CPU clock is selected by setting value of on-chip oscillation division ratio selection register. The division ratio of on-chip oscillation
for CPU clock is selected from among 1/1, 1/2, 1/8, 1/128. The operation clock for the peripheral function block is not changed by
setting value of this register.
■ Notes on On-chip Oscillation Division Ratio
• When system is released from reset, ROSC/8 (on-chip oscillator
middle-speed mode) is selected for CPU clock.
• When state transition from the ceramic or RC oscillation to onchip oscillator, ROSC/8 (on-chip oscillator middle-speed mode)
is selected for CPU clock.
• When the MCU operates by on-chip oscillator for the main clock
without external oscillation circuit, connect X IN pin to V CC
through a resistor and leave XOUT pin open.
Set “10010x002” (x = 0 or 1) to CPUM.
b7
b0
On-chip oscillation division ratio selection register
(RODR: address 003716, initial value: 0216)
On-chip oscillator division ratio
b1 b0
0 0: On-chip oscillator double-speed mode (ROSC/1)
0 1: On-chip oscillator high-speed mode (ROSC/2)
1 0: On-chip oscillator middle-speed mode (ROSC/8)
1 1: On-chip oscillator low-speed mode (ROSC/128)
Not used (returns “0” when read)
Fig. 75 Structure of on-chip oscillation division ratio selection register
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 60 of 93
7546 Group
XIN
XOUT
(Note)
Clock division ratio selection bits
Middle-, high-, double-speed mode
1/2
1/4
Timer 1
Prescaler 1
1/2
On-chip oscillator mode
Clock division
ratio selection bits
Middle-speed mode
Timing φ
(Internal
clock)
High-speed mode
Double-speed mode
On-chip oscillator
1/2
1/4
1/16
ROSC/128
ROSC/8
ROSC/2
ROSC/1
On-chip oscillator division
ratio selection bits
On-chip oscillator
mode
Q
S
Q S
Q
S
RESET
WIT
instruction
STP instruction
R
R
R
STP instruction
Reset
Interrupt disable flag l
Interrupt request
Note: Although a feed-back resistor exists on-chip, an external feed-back resistor
may be needed depending on conditions.
Fig. 76 Block diagram of internal clock generating circuit (for ceramic resonator)
XOUT
XIN
Clock division ratio selection bits
Middle-, high-, double-speed mode
1/2
1/4
Timer 1
Prescaler 1
1/2
On-chip
oscillator
mode
Delay
Clock division
ratio selection bits
Middle-speed mode
Timing φ
(Internal clock)
High-speed mode
Double-speed mode
RING
1/2
On-chip oscillator
1/4
1/16
On-chip oscillator division
ROSC/128 ratio selection bits
ROSC/8
ROSC/2
On-chip oscillator
mode
ROSC/1
S
Q S
R
STP instruction
WIT
instruction
R
Reset
Interrupt disable flag l
Interrupt request
Fig. 77 Block diagram of internal clock generating circuit (for RC oscillation)
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 61 of 93
Q
Q
S
RESET
R
STP instruction
7546 Group
STP mode
f(XIN) oscillation: stop
On-chip oscillator: stop
Interrupt
f(XIN) oscillation: enabled
On-chip oscillator: stop
WAIT mode 2
WIT
instruction
Interrupt
Interrupt
STP
instruction
WIT
instruction
Interrupt
STP
instruction
f(XIN) oscillation: enabled
On-chip oscillator: enabled
f(XIN) oscillation: stop
On-chip oscillator: enabled
WAIT mode 3
WAIT mode 4
Interrupt
WIT
instruction
CPUM76=102
(Note 3)
CPUM3=02
State 1
STP
instruction
Interrupt
f(XIN) oscillation: enabled
On-chip oscillator: enabled
WAIT mode 1
Interrupt
STP
instruction
State 2
MISRG1=12
MISRG1=02
WIT
instruction
State 4
CPUM4=12
MISRG1=12
(Note 4)
MISRG1=02
CPUM76=102
(Note 3)
State 2’
CPUM76=002
012
112
Interrupt
WIT
instruction
CPUM4=02
State 3
CPUM76=002
012
112
(Note 4)
CPUM3=12
Interrupt
State 3’
WIT
instruction
Reset
released
(Note 3)
RESET state
f(XIN) oscillation: enabled
On-chip oscillator: enabled
Interrupt
WAIT mode 2’
WAIT mode 3’
f(XIN) oscillation: enabled
On-chip oscillator: enabled
f(XIN) oscillation: enabled
On-chip oscillator: enabled
Oscillation stop detection circuit valid
Operation clock source: f(XIN) (Note 1)
Operation clock source: On-chip oscillator (Note 2)
Notes on switch of clock
(1) In operation clock = f(XIN), the following can be selected for the CPU clock division ratio.
f(XIN)/2 (high-speed mode)
f(XIN)/8 (middle-speed mode)
f(XIN) (double-speed mode, only at a ceramic oscillation)
(2) In operation clock = On-chip oscillator, the following can be selected for the CPU clock division ratio.
ROSC/1 (On-chip oscillator double-speed mode)
ROSC/2 (On-chip oscillator high-speed mode)
ROSC/8 (On-chip oscillator middle-speed mode)
ROSC/128 (On-chip oscillator low-speed mode)
(3) After system is released from reset, and state transition of state 2 → state 3 and state transition of state 2’ → state 3’,
ROSC/8 (On-chip oscillator middle-speed mode) is selected for CPU clock.
(4) Executing the state transition state 3 to 2 or state 3’ to 2’ after stabilizing XIN oscillation.
(5) When the state 2 → state 3 → state 4 is performed, execute the NOP instruction as shown below
according to the division ratio of CPU clock.
1. CPUM76 = 102 (state 2 → state 3)
2. NOP instruction
Transition from Double-speed mode: NOP ✕ 3
Transition from High-speed mode: NOP ✕ 1
Transition from Middle-speed mode: NOP ✕ 0
3. CPU4 = 12 (state 3 → state 4)
(6) When the state 3 → state 2 → state 1 is performed, execute the NOP instruction as shown below
according to the division ratio of CPU clock.
1. CPUM76 = 002 or 012 or 112 (state 3 → state 2)
2. NOP instruction
Transition from On-chip oscillator double-speed mode: NOP ✕ 4
Transition from On-chip oscillator high-speed mode: NOP ✕ 2
Transition from On-chip oscillator middle-speed mode: NOP ✕ 0
Transition from On-chip oscillator low-speed mode: NOP ✕ 0
3. CPUM3 = 12 (state 2 → state 1)
Fig. 78 State transition
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 62 of 93
7546 Group
● Oscillation stop detection circuit
The oscillation stop detection circuit is used for reset occurrence
when a ceramic resonator or RC oscillation circuit stops by disconnection. To use this circuit, set an on-chip oscillator to be in
active.
The oscillation stop detection circuit is in active to set “1” to the
ceramic or RC oscillation stop detection function active bit. When
the oscillation stop detection circuit is in active, ceramic or RC oscillation is watched by the on-chip oscillator. When stop of ceramic
or RC oscillation is detected, the oscillation stop detection status
bit is set to “1”. While “1” is set to the oscillation stop reset bit, internal reset occurs when oscillation stop is detected.
The external reset and the oscillation stop reset can be discriminated by reading the oscillation stop detection status bit.
The oscillation stop detection status bit retains “1”, not initialized,
when the oscillation stop reset occurs. The oscillation stop detection status bit is initialized to “0” when the external reset occurs.
Accordingly, reset by oscillation stop can be confirmed by using
this flag.
■ Notes on Oscillation Stop Detection Circuit
• Do not execute the transition to “state 2’a” shown in Figure 80
because in this “state 2’a”, MCU is stopped without reset even
when XIN oscillation is stopped.
• Ceramic or RC oscillation stop detection function active bit is not
cleared by the oscillation stop internal reset. Accordingly, the
oscillation stop detection circuit is in active when system is released from internal reset cause of oscillation stop detection.
• Oscillation stop detection status bit is initialized by the following
operation.
(1) External reset
(2) Write “0” data to the ceramic or RC oscillation stop detection
function active bit.
• The oscillation stop detection circuit is not included in the emulator MCU “M37542RSS”.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 63 of 93
b7
b0
MISRG(address 003816, initial value: 0016)
Oscillation stabilization time set bit after
release of the STP instruction
0: Set “0116” in timer1, and “FF16”
in prescaler 1 automatically
1: Not set automatically
Ceramic or RC oscillation stop
detection function active bit
0: Detection function inactive
1: Detection function active
Oscillation stop reset bit
0: Oscillation stop reset disabled
1: Oscillation stop reset enabled
Oscillation stop detection status bit
0: Oscillation stop not detected
1: Oscillation stop detected
Not used (return “0” when read)
Reserved bits
(Do not write “1” to these bits)
Fig. 79 Structure of MISRG
7546 Group
CPUM76=102
(Note 4)
State 2
f(XIN) oscillation: enabled
On-chip oscillator: enabled
MISRG1=12
State 2’
MISRG1=02
(MISRG3 is cleared to “0”.)
State 3
CPUM76=002
012
112
(Note 3)
f(XIN) oscillation: enabled
On-chip oscillator: enabled
State 2’a (Note 5)
Prohibitive state
MUC will be locked when Ceramic
or RC oscillation is stopped.
MISRG2=12
State 2’b
When oscillation stop is detected;
MISRG3 is set to “1”.
Internal RESET occurs.
MISRG1=02
(MISRG3 is cleared to “0”.)
RESET state 1
f(XIN) oscillation: enabled
On-chip oscillator: enabled
Applied “L” to RESET pin
(external reset)
MISRG3 is cleared to “0”.
f(XIN) oscillation: enabled
On-chip oscillator: enabled
Oscillation stop reset disabled
CPUM76=102
CPUM76=002
012
112
MISRG2=02
Oscillation stop reset enabled
(Note 4)
State 3’a
Oscillation stop reset disabled
When oscillation stop is detected;
MISRG3 is set to “1”.
Internal RESET does not occur.
MISRG1=12
(Note 3)
State 3’
Reset
released
f(XIN) oscillation: enabled
On-chip oscillator: enabled
When oscillation stop is detected;
MISRG3 is set to “1”.
Internal RESET does not occur.
State 3’c
Release from internal reset
MISRG3 is set to “1”.
Oscillation status can be
confirmed by reading MISRG3.
MISRG2=12
CPUM76=102
(Note 4)
CPUM76=002
012
112
Reset
released
RESET state 2
(Note 4)
f(XIN) oscillation: enabled
On-chip oscillator: enabled
MISRG2=02
State 3’b
Oscillation stop reset enabled
When oscillation stop is detected;
MISRG3 is set to “1”.
Internal RESET occurs.
Oscillation stop is detected
(internal reset)
Oscillation stop detection circuit is in active. (Note 6)
Operation clock source: f(XIN) (Note 1)
Operation clock source: On-chip oscillator (Note 2)
Notes on switch of clock
(1) In operation clock = f(XIN), the following can be selected for the CPU clock division ratio.
f(XIN)/2 (High-speed mode)
f(XIN)/8 (Middle-speed mode)
f(XIN) (Double-speed mode, only at a ceramic oscillation)
(2) In operation clock = On-chip oscillator, the following can be selected for the CPU clock division ratio.
ROSC/1 (On-chip oscillator double-speed mode)
ROSC/2 (On-chip oscillator high-speed mode)
ROSC/8 (On-chip oscillator middle-speed mode)
ROSC/128 (On-chip oscillator low-speed mode)
(3) Executing the state transition state 3 to 2 or state 3 to 3’ after stabilizing XIN oscillation.
(4) After system is released from reset, and state transition of state 2 → state 3 and state transition of state 2’ → state 3’,
ROSC/8 (On-chip oscillator middle-speed mode) is selected for CPU clock.
(5) MCU cannot be returned by On-chip oscillator and its operation is stopped since internal reset does not occur at oscillation stop detected.
Accordingly, do not execute the transition to state 2'a.
(6) STP instruction cannot be used when oscillation stop detection circuit is in active.
Fig. 80 State transition 2
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 64 of 93
7546 Group
● Function set ROM
b7
Figure 82 shows the Assignment of Function set ROM area.
The random data are written to the Renesas shipment test areas
(addresses FFD416 to address FFD716).
Do not rewrite the data of these areas.
When the checksum is included in the user program, avoid assigning it to these areas.
The function set ROM data 0 to 2 (addresses FFD816 to FFDA16)
are used to set the peripheral function.
Data set to these areas become valid after releasing reset.
The ROM code protect to disable the reading of the built-in
QzROM area is assigned to address FFDB16.
[Function set ROM data] FSROM0, FSROM1, FSROM2
Function set ROM data 0 to 2 (addresses FFD816 to FFDA16) are
used to set modes of peripheral functions.
By setting values to these areas, the operation mode of each peripheral function are set after releasing reset.
Refer to the descriptions of peripheral functions for the details of
operation of peripheral functions.
- CPU mode register
- Watchdog timer
- Low voltage detection circuit
When “1” is set to bit 0 of function set ROM data 0 (address
FFD816), the written values to bit 5 to bit 0 of function set ROM
data 2 (address FFDA16) can become invalid.
When the values of bit 5 to bit 0 of function set ROM data 2 (address FFDA16) are invalid, the operation mode of the peripheral
functions can be set by setting the related registers.
b0
1 0
0 0
Function set ROM data 0
(FSROM0: address FFD816)
0
Function set ROM invalid bit (Note 1)
0: Setting of bit 5 to bit 0 of function set
ROM data 2 valid
1: Setting of bit 5 to bit 0 of function set
ROM data 2 invalid
Low voltage detection circuit valid bit
0: Low voltage detection circuit invalid
1: Low voltage detection circuit valid
Set “0” to this bit certainly.
Low voltage detection circuit valid bit
in the stop mode (Note 2)
0: Low voltage detection circuit invalid
in the stop mode
1: Low voltage detection circuit valid
in the stop mode
Set “0” to these bits.
Set “1” to this bit.
Note 1: When “1” is set to this bit, the setting values of bit 5 to bit 0 of function
set ROM data 2 become invalid, and these functions can be set by
program. (this bit does not affect on other bits than bit 5 to bit 0 of
function set ROM data 2.)
2: When the Low voltage detection circuit is set to be valid in the stop
mode, the dissipation current in the stop mode is increased.
Fig. 83 Structure of Function set ROM data 0
b7
b0
0 0 0 0 0 0 0 0
Function set ROM data 1
FSROM1 (FFD916)
Set “0” to these bits certainly.
Fig. 84 Structure of Function set ROM data 1
[ROM code protect]
By setting “0016” to ROM code protect (address FFDB16), reading
of the built-in QzROM by the serial programmer is disabled.
b7
0 0
Addres
FFD416 Renesas shipment test area
FFD5 16 Renesas shipment test area
FFD6 16 Renesas shipment test area
FFD7 16 Renesas shipment test area
FFD8 16 Function set ROM data 0
FFD9 16 Function set ROM data 1
FFDA 16 Function set ROM data 2
FFDB 16 ROM code protect
Interrupt vector area
Note: The random data are written into the
Renesas shipment test areas
(address FFD416 to address FFD716).
Do not rewrite the data of these areas.
When checksum is included in user program,
avoid assigning it to these areas.
Fig. 82 Assignment of Function set ROM area
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 65 of 93
b0
Function set ROM data 2
(FSROM2: address FFDA16)
Watchdog timer source clock
selection bit (Note 1)
0 : On-chip oscillator/16
1 : On-chip oscillator/16 or f(XIN)/16
Watchdog timer start selection bit (Note 1)
0 : Watchdog timer starts automatically after reset
1 : Watchdog timer is inactive after reset
Watchdog timer H count source
selection bit (Note 1)
0 :Watchdog timer L underflow
1 : Count source of watchdog timer L
(The clock selected by the watchdog timer
source clock selection bit (bit 0))
STP instruction function selection bit (Note 1)
0 : System enters into the stop mode
at the STP instruction execution
1 : Internal reset occurs at the STP instruction execution
On-chip oscillator control bit (Note 1)
0 : Stop of on-chip oscillator disabled
1 : Stop of on-chip oscillator enabled
Oscillation mode selection bit (Note 1)
0 : Ceramic oscillation
1 : RC oscillation
Set “0” to these bits certainly.
Note 1: These functions can be active when “0” is set to function set
ROM valid bit (bit 0 of function set ROM data 0).
Fig. 85 Structure of Function set ROM data 2
7546 Group
NOTES ON PROGRAMMING
State transition
Processor Status Register
Do not stop the clock selected as the operation clock because of
setting of CM3, 4.
The contents of the processor status register (PS) after reset are
undefined except for the interrupt disable flag I which is “1”. After
reset, initialize flags which affect program execution. In particular,
it is essential to initialize the T flag and the D flag because of their
effect on calculations.
Interrupts
The contents of the interrupt request bit do not change even if the
BBC or BBS instruction is executed immediately after they are
changed by program because this instruction is executed for the
previous contents. For executing the instruction for the changed
contents, execute one instruction before executing the BBC or
BBS instruction.
Decimal Calculations
• For calculations in decimal notation, set the decimal mode flag
D to “1”, then execute the ADC instruction or SBC instruction. In
this case, execute SEC instruction, CLC instruction or CLD instruction after executing one instruction before the ADC instruction
or SBC instruction.
• In the decimal mode, the values of the N (negative), V (overflow)
and Z (zero) flags are invalid.
Ports
• The values of the port direction registers cannot be read.
That is, it is impossible to use the LDA instruction, memory operation instruction when the T flag is “1”, addressing mode using
direction register values as qualifiers, and bit test instructions such
as BBC and BBS.
It is also impossible to use bit operation instructions such as CLB
and SEB and read/modify/write instructions of direction registers
for calculations such as ROR.
For setting direction registers, use the LDM instruction, STA instruction, etc.
A/D Conversion
Do not execute the STP instruction during A/D conversion.
Instruction Execution Timing
The instruction execution time can be obtained by multiplying the
frequency of the internal clock φ by the number of cycles mentioned in the machine-language instruction table.
The frequency of the internal clock φ is the same as that of the XIN
in double-speed mode, twice the X IN cycle in high-speed mode
and 8 times the XIN cycle in middle-speed mode.
CPU Mode Register
The oscillation mode selection bit and processor mode bits can be
rewritten only once after releasing reset. However, after rewriting it
is disable to write any value to the bit. (Emulator MCU is excluded.)
When a ceramic oscillation is selected, a double-speed mode of
the clock division ratio selection bits can be used. Do not use it
when an RC oscillation is selected.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 66 of 93
NOTES ON HARDWARE
Handling of Power Source Pin
In order to avoid a latch-up occurrence, connect a capacitor suitable for high frequencies as bypass capacitor between power
source pin (Vcc pin) and GND pin (Vss pin). Besides, connect the
capacitor to as close as possible. For bypass capacitor which
should not be located too far from the pins to be connected, a ceramic capacitor of 0.01 µF to 0.1 µF is recommended.
7546 Group
NOTES ON USE
Countermeasures against noise
1. Shortest wiring length
(1) Package
Select the smallest possible package to make the total wiring
length short.
<Reason>
The wiring length depends on a microcomputer package. Use of a
small package, for example QFP and not DIP, makes the total wiring length short to reduce influence of noise.
DIP
(3) Wiring for clock input/output pins
• Make the length of wiring which is connected to clock I/O pins as
short as possible.
• Make the length of wiring (within 20 mm) across the grounding
lead of a capacitor which is connected to an oscillator and the
VSS pin of a microcomputer as short as possible.
• Separate the VSS pattern only for oscillation from other VSS patterns.
<Reason>
If noise enters clock I/O pins, clock waveforms may be deformed.
This may cause a program failure or program runaway. Also, if a
potential difference is caused by the noise between the VSS level
of a microcomputer and the VSS level of an oscillator, the correct
clock will not be input in the microcomputer.
Noise
SDIP
SOP
QFP
Fig. 84 Selection of packages
Noise
RESET
VSS
VSS
XIN
XOUT
VSS
O.K.
N.G.
(2) Wiring for RESET pin
Make the length of wiring which is connected to the RESET pin as
short as possible. Especially, connect a capacitor across the
RESET pin and the V SS pin with the shortest possible wiring
(within 20mm).
<Reason>
The width of a pulse input into the RESET pin is determined by the
timing necessary conditions. If noise having a shorter pulse width
than the standard is input to the RESET pin, the reset is released
before the internal state of the microcomputer is completely initialized. This may cause a program runaway.
Reset
circuit
XIN
XOUT
VSS
Fig. 86 Wiring for clock I/O pins
(4) Wiring to VPP pin
Connect VPP pin to a GND pattern at the shortest distance.
The GND pattern is required to be as close as possible to the
GND supplied to VSS.
In order to improve the noise reduction, to connect a 5 kΩ resistor
serially to the VPP pin - GND line may be valid.
As well as the above-mentioned, in this case, connect to a GND
pattern at the shortest distance. The GND pattern is required to be
as close as possible to the GND supplied to VSS.
<Reason>
The VPP pin of the QzROM is the power source input pin for the
built-in QzROM. When programming in the built-in QzROM, the
impedance of the V PP pin is low to allow the electric current for
writing flow into the QzROM. Because of this, noise can enter easily. If noise enters the VPP pin, abnormal instruction codes or data
are read from the built-in QzROM, which may cause a program
runaway.
N.G.
(Note)
The shortest
CNVSS/VPP
Reset
circuit
VSS
About 5kΩ
RESET
VSS
(Note)
The shortest
VSS
Note: This indicates pin.
O.K.
Fig. 85 Wiring for the RESET pin
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 67 of 93
Fig. 87 Wiring for the VPP pin of the QzPROM
7546 Group
2. Connection of bypass capacitor across VSS line and VCC line
Connect an approximately 0.1 µF bypass capacitor across the VSS
line and the VCC line as follows:
• Connect a bypass capacitor across the VSS pin and the VCC pin
at equal length.
• Connect a bypass capacitor across the VSS pin and the VCC pin
with the shortest possible wiring.
• Use lines with a larger diameter than other signal lines for VSS
line and VCC line.
• Connect the power source wiring via a bypass capacitor to the
VSS pin and the VCC pin.
AA
AA
AA
AA
AA
VCC
VSS
N.G.
AA
AA
AA
AA
AA
VCC
VSS
3. Wiring to analog input pins
• Connect an approximately 100 Ω to 1 kΩ resistor to an analog
signal line which is connected to an analog input pin in series.
Besides, connect the resistor to the microcomputer as close as
possible.
• Connect an approximately 1000 pF capacitor across the Vss pin
and the analog input pin. Besides, connect the capacitor to the
Vss pin as close as possible. Also, connect the capacitor across
the analog input pin and the Vss pin at equal length.
<Reason>
Signals which is input in an analog input pin (such as an A/D converter/comparator input pin) are usually output signals from
sensor. The sensor which detects a change of event is installed far
from the printed circuit board with a microcomputer, the wiring to
an analog input pin is longer necessarily. This long wiring functions as an antenna which feeds noise into the microcomputer,
which causes noise to an analog input pin.
Noise
(Note)
Microcomputer
O.K.
Fig. 88 Bypass capacitor across the VSS line and the VCC line
Analog
input pin
Thermistor
N.G.
O.K.
VSS
Note : The resistor is used for dividing
resistance with a thermistor.
Fig. 89 Analog signal line and a resistor and a capacitor
• The analog input pin is connected to the capacitor of a voltage
comparator. Accordingly, sufficient accuracy may not be obtained by the charge/discharge current at the time of A/D
conversion when the analog signal source of high-impedance is
connected to an analog input pin. In order to obtain the A/D conversion result stabilized more, please lower the impedance of an
analog signal source, or add the smoothing capacitor to an analog input pin.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 68 of 93
7546 Group
4. Oscillator concerns
Take care to prevent an oscillator that generates clocks for a microcomputer operation from being affected by other signals.
(1) Keeping oscillator away from large current signal lines
Install a microcomputer (and especially an oscillator) as far as
possible from signal lines where a current larger than the tolerance of current value flows.
<Reason>
In the system using a microcomputer, there are signal lines for
controlling motors, LEDs, and thermal heads or others. When a
large current flows through those signal lines, strong noise occurs
because of mutual inductance.
(2) Installing oscillator away from signal lines where potential levels change frequently
Install an oscillator and a connecting pattern of an oscillator away
from signal lines where potential levels change frequently. Also, do
not cross such signal lines over the clock lines or the signal lines
which are sensitive to noise.
<Reason>
Signal lines where potential levels change frequently (such as the
CNTR pin signal line) may affect other lines at signal rising edge
or falling edge. If such lines cross over a clock line, clock waveforms may be deformed, which causes a microcomputer failure or
a program runaway.
(3) Oscillator protection using Vss pattern
As for a two-sided printed circuit board, print a Vss pattern on the
underside (soldering side) of the position (on the component side)
where an oscillator is mounted.
Connect the Vss pattern to the microcomputer Vss pin with the
shortest possible wiring. Besides, separate this Vss pattern from
other Vss patterns.
An example of VSS patterns on the
underside of a printed circuit board
A
AAA
A
AAA
A
A
AA
AAA
A
A
AA
Oscillator wiring
pattern example
XIN
XOUT
VSS
Separate the VSS line for oscillation from other VSS lines
Fig. 91 Vss pattern on the underside of an oscillator
➀ Keeping oscillator away from large current signal lines
Microcomputer
Mutual inductance
M
XIN
XOUT
VSS
Large
current
GND
➁ Installing oscillator away from signal lines where potential levels change frequently
N.G.
Do not cross
CNTR
XIN
XOUT
VSS
Fig. 90 Wiring for a large current signal line/Writing of signal
lines where potential levels change frequently
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 69 of 93
7546 Group
5. Setup for I/O ports
Setup I/O ports using hardware and software as follows:
<Hardware>
• Connect a resistor of 100 Ω or more to an I/O port in series.
<Software>
• As for an input port, read data several times by a program for
checking whether input levels are equal or not.
• As for an output port, since the output data may reverse because
of noise, rewrite data to its port latch at fixed periods.
• Rewrite data to direction registers and pull-up control registers at
fixed periods.
O.K.
Noise
Data bus
Noise
Direction register
N.G.
Port latch
I/O port
pins
Fig. 92 Setup for I/O ports
6. Providing of watchdog timer function by software
If a microcomputer runs away because of noise or others, it can
be detected by a software watchdog timer and the microcomputer
can be reset to normal operation. This is equal to or more effective
than program runaway detection by a hardware watchdog timer.
The following shows an example of a watchdog timer provided by
software.
In the following example, to reset a microcomputer to normal operation, the main routine detects errors of the interrupt processing
routine and the interrupt processing routine detects errors of the
main routine.
This example assumes that interrupt processing is repeated multiple times in a single main routine processing.
<The main routine>
• Assigns a single byte of RAM to a software watchdog timer
(SWDT) and writes the initial value N in the SWDT once at each
execution of the main routine. The initial value N should satisfy
the following condition:
N+1 ≥ (Counts of interrupt processing executed in each main
routine)
As the main routine execution cycle may change because of an
interrupt processing or others, the initial value N should have a
margin.
• Watches the operation of the interrupt processing routine by
comparing the SWDT contents with counts of interrupt processing after the initial value N has been set.
• Detects that the interrupt processing routine has failed and determines to branch to the program initialization routine for
recovery processing in the following case:
If the SWDT contents do not change after interrupt processing.
<The interrupt processing routine>
• Decrements the SWDT contents by 1 at each interrupt processing.
• Determines that the main routine operates normally when the
SWDT contents are reset to the initial value N at almost fixed
cycles (at the fixed interrupt processing count).
• Detects that the main routine has failed and determines to
branch to the program initialization routine for recovery processing in the following case:
If the SWDT contents are not initialized to the initial value N but
continued to decrement and if they reach 0 or less.
≠N
Main routine
Interrupt processing routine
(SWDT)← N
(SWDT) ← (SWDT)—1
CLI
Interrupt processing
Main processing
(SWDT)
≤0?
(SWDT)
=N?
N
Interrupt processing
routine errors
Fig. 93 Watchdog timer by software
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 70 of 93
≤0
>0
RTI
Return
Main routine
errors
7546 Group
ELECTRICAL CHARACTERISTICS of 7546 Group
Absolute Maximum Ratings
Absolute maximum ratings
Symbol
VCC
VI
VI
VI
VO
Pd
Topr
Tstg
Parameter
Power source voltage
Input voltage
P00–P07, P10–P14, P20–P25, P30–P34, P37, VREF
Input voltage RESET, XIN
Input voltage CNVSS
Output voltage
P00–P07, P10–P14, P20–P25, P30–P34, P37, XOUT
Power dissipation
Operating temperature
Storage temperature
Note : 200 mW for the PLQP0032GB-A package product.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 71 of 93
Conditions
All voltages are
based on VSS.
When an input
voltage is measured, output
transistors are cut
off.
Ta = 25°C
Ratings
–0.3 to 6.5
–0.3 to VCC + 0.3
Unit
V
V
–0.3 to VCC + 0.3
–0.3 to VCC + 0.3
–0.3 to VCC + 0.3
V
V
V
300 (Note)
–20 to 85
–40 to 125
mW
°C
°C
7546 Group
Recommended Operating Conditions
Recommended operating conditions (1)
(VCC = 1.8 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Symbol
VCC
Parameter
Power source voltage (Double-speed mode)
(ceramic)
f(XIN) = 8 MHz
f(XIN) = 6.5 MHz
f(XIN) = 2 MHz
f(XIN) = 1 MHz
(High-, Middle-speed mode) f(XIN) = 8 MHz
f(XIN) = 4 MHz
f(XIN) = 2 MHz
Power source voltage (High-, Middle-speed mode) f(XIN) = 4 MHz
(RC)
f(XIN) = 2 MHz
f(XIN) = 1 MHz
Power source voltage (at on-chip oscillator)
VSS
Power source voltage
VREF
Analog reference voltage
VIH
“H” input voltage
P00–P07, P10–P14, P20–P25, P30–P34, P37
VIH
“H” input voltage (TTL input level selected)
P10, P12, P13, P37 (Note 1)
VIH
“H” input voltage
RESET, XIN
VIL
“L” input voltage
P00–P07, P10–P14, P20–P25, P30–P34, P37
VIL
“L” input voltage (TTL input level selected)
P10, P12, P13, P37 (Note 1)
VIL
“L” input voltage
RESET, CNVSS
VIL
“L” input voltage
XIN
∑IOH(peak) “H” total peak output current (Note 2)
P00–P07, P10–P14, P20–P25, P30–P34, P37
∑IOL(peak) “L” total peak output current (Note 2)
P10–P14, P20–P25
∑IOL(peak) “L” total peak output current (Note 2)
P00–P07, P30–P34, P37
∑IOH(avg) “H” total average output current (Note 2)
P00–P07, P10–P14, P20–P25, P30–P34, P37
∑IOL(avg) “L” total average output current (Note 2)
P10–P14, P20–P25
∑IOL(avg) “L” total average output current (Note 2)
P00–P07, P30–P34, P37
Limits
Min.
4.5
4.0
2.4
2.2
4.0
2.4
2.2
4.0
2.4
2.2
1.8
Typ.
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
0
Max.
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
Unit
1.8
0.8VCC
VCC
VCC
V
V
V
V
V
V
V
V
V
V
V
V
V
V
2.0
VCC
V
0.8VCC
VCC
V
0
0.2VCC
V
0
0.8
V
0
0.2VCC
V
0
0.16VCC
V
–80
mA
80
mA
80
mA
–40
mA
40
mA
40
mA
Note 1: Vcc = 4.0 to 5.5V
2: The total output current is the sum of all the currents flowing through all the applicable ports. The total average current is an average value measured
over 100 ms. The total peak current is the peak value of all the currents.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 72 of 93
7546 Group
Recommended operating conditions (2)
(VCC = 1.8 to 5.5V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Symbol
Parameter
IOH(peak)
IOL(peak)
“H” peak output current (Note 1)
“L” peak output current (Note 1)
P00–P07, P10–P14, P20–P25, P30–P34, P37
P00–P07, P30–P34, P37 (Drive capacity = “L”)
P10–P14, P20–P25
IOL(peak)
IOH(avg)
IOL(avg)
“L” peak output current (Note 1)
“H” average output current (Note 2)
“L” average output current (Note 2)
IOL(avg)
f(XIN)
P00–P07, P30–P34, P37 (Drive capacity = “H”)
P00–P07, P10–P14, P20–P25, P30–P34, P37
P00–P07, P30–P34, P37 (Drive capacity = “L”)
P10–P14, P20–P25
P00–P07, P30–P34, P37 (Drive capacity = “H”)
“L” average output current (Note 2)
Oscillation frequency (Note 3)
at ceramic oscillation or external clock input
(VCC = 4.5 V to 5.5 V) Double-speed mode
Oscillation frequency (Note 3)
at ceramic oscillation or external clock input
(VCC = 4.0 V to 5.5 V) Double-speed mode
Oscillation frequency (Note 3)
at ceramic oscillation or external clock input
(VCC = 2.4 V to 5.5 V) Double-speed mode
Oscillation frequency (Note 3)
at ceramic oscillation or external clock input
(VCC = 2.2 V to 5.5 V) Double-speed mode
Oscillation frequency (Note 3)
at ceramic oscillation or external clock input
(VCC = 4.0 V to 5.5 V) High-, Middle-speed mode
Oscillation frequency (Note 3)
at ceramic oscillation or external clock input
(VCC = 2.4 V to 5.5 V) High-, Middle-speed mode
Oscillation frequency (Note 3)
at ceramic oscillation or external clock input
(VCC = 2.2 V to 5.5 V) High-, Middle-speed mode
Oscillation frequency (Note 3)
at RC oscillation
(VCC = 4.0 V to 5.5 V) High-, Middle-speed mode
Oscillation frequency (Note 3)
at RC oscillation
(VCC = 2.4 V to 5.5 V) High-, Middle-speed mode
Oscillation frequency (Note 3)
at RC oscillation
(VCC = 2.2 V to 5.5 V) High-, Middle-speed mode
Notes 1: The peak output current is the peak current flowing in each port.
2: The average output current IOL (avg), IOH (avg) in an average value measured over 100 ms.
3: When the oscillation frequency has a duty cycle of 50 %.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 73 of 93
Min.
Typ.
Unit
Max.
–10
10
mA
mA
30
–5
5
mA
mA
mA
15
8
mA
MHz
6.5
MHz
2
MHz
1
MHz
8
MHz
4
MHz
2
MHz
4
MHz
2
MHz
1
MHz
7546 Group
Electrical Characteristics
Electrical characteristics (1)
(VCC = 1.8 to 5.5V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Symbol
VOH
VOL
VOL
Parameter
“H” output voltage
P00–P07, P10–P14, P20–P25,
P30–P34, P37 (Note 1)
“L” output voltage
P00–P07, P30–P34, P37 (Drive capacity = “L”)
P10–P14, P20–P25
“L” output voltage
P00–P07, P30–P34, P37 (Drive capacity = “H”)
VT+–VT– Hysteresis
CNTR0, INT0, INT1, CAP0, CAP1 (Note 2)
P00–P07 (Note 3)
VT+–VT– Hysteresis
RXD0, SCLK0, RXD1, SCLK1
VT+–VT– Hysteresis
RESET
IIH
“H” input current
P00–P07, P10–P14, P20–P25, P30–P34, P37
IIH
IIH
IIL
IIL
IIL
IIL
VRAM
ROSC
DOSC
“H” input current
RESET
“H” input current
XIN
“L” input current
P00–P07, P10–P14, P20–P25, P30–P34, P37
“L” input current
RESET
“L” input current
XIN
“L” input current
P00–P07, P30–P34, P37
RAM hold voltage
On-chip oscillator oscillation frequency
Oscillation stop detection circuit detection frequency
Test conditions
IOH = –5 mA
VCC = 4.0 to 5.5 V
IOH = –1.0 mA
VCC = 1.8 to 5.5 V
IOL = 5 mA
VCC = 4.0 to 5.5 V
IOL = 1.5 mA
VCC = 4.0 to 5.5 V
IOL = 1.0 mA
VCC = 1.8 to 5.5 V
IOL = 15 mA
VCC = 4.0 to 5.5 V
IOL = 1.5 mA
VCC = 4.0 to 5.5 V
IOL = 1.0 mA
VCC = 1.8 to 5.5 V
Min.
Typ.
page 74 of 93
Unit
VCC–1.5
V
VCC–1.0
V
1.5
V
0.3
V
1.0
V
2.0
V
0.3
V
1.0
V
0.4
V
0.5
V
0.5
V
VI = VCC
(Pin floating. Pull up transistors
“off”)
VI = VCC
5.0
µA
5.0
µA
µA
4.0
VI = VCC
VI = VSS
(Pin floating. Pull up transistors
“off”)
VI = VSS
–5.0
µA
–5.0
µA
µA
VI = VSS
–4.0
VI = VSS
(Pull up transistors “on”)
When clock stopped
VCC = 5.0 V, Ta = 25 °C
VCC = 5.0 V, Ta = 25 °C
–0.2
–0.5
mA
2000
125
5.5
3000
187.5
V
kHz
kHz
1.6
1000
62.5
Notes1: P11 is measured when the P11/TXD1 P-channel output disable bit of the UART1 control register (bit 4 of address 001B16) is “0”.
P05 is measured when the P05/TXD2 P-channel output disable bit of the UART2 control register (bit 4 of address 003116) is “0”.
2: RXD1, SCLK1 and INT0 have hysteresises only when bits 0 to 2 of the port P1P3 control register are set to “0” (CMOS level).
3: It is available only when operating key-on wake up.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
Max.
7546 Group
Electrical characteristics (2)
(VCC = 1.8 to 5.5V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Symbol
ICC
Parameter
Test conditions
Power source f(XIN) = 8 MHz
current
Output transistors “off”
*LVD is valid
(except at STP) f(XIN) = 2 MHz,
VCC = 2.2 V
Output transistors “off”
On-chip oscillator
operation mode,
Output transistors “off”
Output transistors “off”
Low voltage detection
circuit self consumption
current
Max.
Double-speed mode
High-speed mode
Middle-speed mode
High-speed mode
5.9
3.9
2.4
0.45
9.5
7.0
5.5
1.25
mA
mA
mA
mA
Frequency/1
Frequency/2
Frequency/8
Frequency/128
1.55
0.95
0.4
0.25
2.0
3.3
2.3
1.1
0.7
3.5
mA
mA
mA
mA
mA
Ta = 25 °C
VCC = 5 V
Note: Increment when A/D conversion is executed includes the reference power source input current (IVREF).
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 75 of 93
Unit
Typ.
f(XIN) = 8 MHz (in WIT state),
functions except timer 1 disabled,
Output transistors “off”
f(XIN) = 2 MHz, VCC = 2.2 V
(in WIT state),
functions except timer 1 disabled,
Output transistors “off”
On-chip oscillator operation mode,
(in WIT state),
functions except timer 1 disabled,
Output transistors “off”
Increment when A/D conversion is executed
f(XIN) = 8 MHz, VCC = 5 V
Ta = 25 °C
All oscillation stopped
Ta = 85 °C
(in STP state)
Min.
mA
0.25
0.25
0.7
mA
0.5
0.1
70
mA
1.0
10
µA
µA
µA
7546 Group
A/D Converter Characteristics
A/D Converter characteristics
(VCC = 2.7 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Symbol
Parameter
—
—
Resolution
Absolute accuracy
tCONV
Conversion time
RLADDER Ladder resistor
IVREF
Reference power source input current
II(AD)
A/D port input current
Test conditions
Limits
Min.
Typ.
Ta = 25 °C
VCC = VREF = 2.7 to 5.5 V
AD conversion clock = f(XIN)/2
AD conversion clock = f(XIN)
VREF = 5.0 V
VREF = 3.0 V
50
30
55
150
90
Max.
10
±3
Bits
LSB
122
61
tc(XIN)
200
120
5.0
Note: AD conversion accuracy may be low under the following conditions;
(1) When the VREF voltage is set to be lower than the VCC voltage, an analog circuit in this microcomputer is affected by noise.
The accuracy is lower than the case the VREF voltage is the same as VCC voltage.
(2) When the VREF voltage is 3.0 V or less at the low temperature, the AD conversion accuracy may be very lower than at room temperature.
When system is used at low temperature, that VREF is 3.0 V or more is recommended.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 76 of 93
Unit
kΩ
µA
µA
7546 Group
Power-on reset circuit characteristics
Power-on reset circuit characteristics
(VCC = 1.8 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Symbol
Parameter
VPOR
TW(VPOR)
TW(VPOR-VDET)
Test conditions
Valid start voltage of power-on reset circuit (Note)
VPOR hold time
Limits
Min.
Typ.
Max.
0
10
20
TW(VPOR) > 10 s
Rising time of valid power source of power-on reset circuit
Unit
mV
s
ms
Note: VPOR is the start voltage level of Vcc for the built-in power-on reset circuit to operate normally.
Keep VPOR to be lower than the Vcc voltage before rising of the Vcc power source to use the built-in power-on reset circuit.
Set the built-in low voltage detection circuit to be valid when the built-in power-on reset is used.
Low voltage detection circuit characteristics
Low voltage detection circuit characteristics
(VCC = 1.8 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Symbol
Parameter
VLVD
TW(VLVD)
TW(VLVD-VDET)
VDET-
Test conditions
Valid start voltage of low voltage detection circuit (Note)
VLVD hold time
Rising time of valid power source of low voltage detection circuit TW(VLVD) > 10 s
Detection voltage of low voltage detection circuit
Ta = 0 to 50 °C
Ta = –20 to 85 °C
V(VDET+–VDET-) Detection voltage Hysteresis (when hysteresis is valid)
Ta = –20 to 85 °C
TDET
Detection time of low 5voltage detection circuit
Limits
Min.
1.0
Typ.
1.85
1.8
1.95
1.95
0.1
20
Max.
0
10
10
2.05
2.1
Unit
V
s
s
V
V
V
µs
Note: VLVD is the start voltage level of Vcc for the built-in low voltage detection circuit to operate normally.
If the Vcc power source becomes lower than VLVD, first set the Vcc voltage to be lower than VPOR. Next, according to the electrical characteristics of
the power-on reset circuit, perform the rising of Vcc.
VDET+
VDET-
Vcc power source
waveform
Note
VPOR
VPOR
0V
TW(VPOR)
T(VPON-VDET)
TDET
TW(VLVD)
T(VLVD-VDET)
Internal reset signal
Power-on reset circuit
characteristics
Low voltage detection circuit
characteristics
Note: If schmitt of the voltage drop detection circuit is set to be invalid, system is released from reset at the timing of rising to
power source voltage VDET-.
Fig. 94 Electrical characteristics of power-on reset circuit and voltage drop detection circuit
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 77 of 93
7546 Group
Timing Requirements
Table 22 Timing requirements (1)
(VCC = 4.0 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Symbol
tW(RESET)
tC(XIN)
tWH(XIN)
tWL(XIN)
tC(CNTR0)
tWH(CNTR0)
tWL(CNTR0)
tC(SCLK1)
tWH(SCLK1)
tWL(SCLK1)
tsu(RxD1–SCLK1)
th(SCLK1–RxD1)
Limits
Parameter
Reset input “L” pulse width
External clock input cycle time
External clock input “H” pulse width
External clock input “L” pulse width
CNTR0 input cycle time
CNTR0, INT0, INT1, CAP0, CAP1 input “H” pulse width (Note 1)
CNTR0, INT0, INT1, CAP0, CAP1 input “L” pulse width (Note 1)
Serial I/O1, serial I/O2 clock input cycle time (Note 2)
Serial I/O1, serial I/O2 clock input “H” pulse width (Note 2)
Serial I/O1, serial I/O2 clock input “L” pulse width (Note 2)
Serial I/O1, serial I/O2 input set up time
Serial I/O1, serial I/O2 input hold time
Min.
2
125
50
50
200
80
80
800
370
370
220
100
Typ.
Unit
Max.
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Notes 1: As for CAP0, CAP1, it is the value when noise filter is not used.
2: In this time, bit 6 of the serial I/O1 control register (address 001A16) is set to “1” (clock synchronous serial I/O is selected).
When bit 6 of the serial I/O1 control register is “0” (clock asynchronous serial I/O is selected), the rating values are divided by 4.
In this time, bit 6 of the serial I/O2 control register (address 003016) is set to “1” (clock synchronous serial I/O is selected).
When bit 6 of the serial I/O2 control register is “0” (clock asynchronous serial I/O is selected), the rating values are divided by 4.
Table 23 Timing requirements (2)
(VCC = 2.4 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Symbol
tW(RESET)
tC(XIN)
tWH(XIN)
tWL(XIN)
tC(CNTR0)
tWH(CNTR0)
tWL(CNTR0)
tC(SCLK1)
tWH(SCLK1)
tWL(SCLK1)
tsu(RxD1–SCLK1)
th(SCLK1–RxD1)
Limits
Parameter
Reset input “L” pulse width
External clock input cycle time
External clock input “H” pulse width
External clock input “L” pulse width
CNTR0 input cycle time
CNTR0, INT0, INT1, CAP0, CAP1 input “H” pulse width (Note 1)
CNTR0, INT0, INT1, CAP0, CAP1 input “L” pulse width (Note 1)
Serial I/O1, serial I/O2 clock input cycle time (Note 2)
Serial I/O1, serial I/O2 clock input “H” pulse width (Note 2)
Serial I/O1, serial I/O2 clock input “L” pulse width (Note 2)
Serial I/O1, serial I/O2 input set up time
Serial I/O1, serial I/O2 input hold time
Min.
2
250
100
100
500
230
230
2000
950
950
400
200
Typ.
Notes 1: As for CAP0, CAP1, it is the value when noise filter is not used.
2: In this time, bit 6 of the serial I/O1 control register (address 001A16) is set to “1” (clock synchronous serial I/O is selected).
When bit 6 of the serial I/O1 control register is “0” (clock asynchronous serial I/O1 is selected), the rating values are divided by 4.
In this time, bit 6 of the serial I/O2 control register (address 003016) is set to “1” (clock synchronous serial I/O is selected).
When bit 6 of the serial I/O2 control register is “0” (clock asynchronous serial I/O is selected), the rating values are divided by 4.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 78 of 93
Unit
Max.
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
7546 Group
Table 24 Timing requirements (3)
(VCC = 2.2 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Symbol
tW(RESET)
tC(XIN)
tWH(XIN)
tWL(XIN)
tC(CNTR0)
tWH(CNTR0)
tWL(CNTR0)
tC(SCLK1)
tWH(SCLK1)
tWL(SCLK1)
tsu(RxD1–SCLK1)
th(SCLK1–RxD1)
Limits
Parameter
Reset input “L” pulse width
External clock input cycle time
External clock input “H” pulse width
External clock input “L” pulse width
CNTR0 input cycle time
CNTR0, INT0, INT1, CAP0, CAP1 input “H” pulse width (Note 1)
CNTR0, INT0, INT1, CAP0, CAP1 input “L” pulse width (Note 1)
Serial I/O1, serial I/O2 clock input cycle time (Note 2)
Serial I/O1, serial I/O2 clock input “H” pulse width (Note 2)
Serial I/O1, serial I/O2 clock input “L” pulse width (Note 2)
Serial I/O1, serial I/O2 input set up time
Serial I/O1, serial I/O2 input hold time
Min.
2
500
200
200
1000
460
460
4000
1900
1900
800
400
Typ.
Notes 1: As for CAP0, CAP1, it is the value when noise filter is not used.
2: In this time, bit 6 of the serial I/O1 control register (address 001A16) is set to “1” (clock synchronous serial I/O is selected).
When bit 6 of the serial I/O1 control register is “0” (clock asynchronous serial I/O1 is selected), the rating values are divided by 4.
In this time, bit 6 of the serial I/O2 control register (address 003016) is set to “1” (clock synchronous serial I/O is selected).
When bit 6 of the serial I/O2 control register is “0” (clock asynchronous serial I/O is selected), the rating values are divided by 4.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 79 of 93
Unit
Max.
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
7546 Group
Switching Characteristics
Table 25 Switching characteristics (1)
(VCC = 4.0 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Symbol
tWH(SCLK1)
tWL(SCLK1)
td(SCLK1–TxD1)
tv(SCLK1–TxD1)
tr(SCLK1)
tf(SCLK1)
tr(CMOS)
tf(CMOS)
Parameter
Serial I/O1, serial I/O2 clock output “H” pulse width
Serial I/O1, serial I/O2 clock output “L” pulse width
Serial I/O1, serial I/O2 output delay time
Serial I/O1, serial I/O2 output valid time
Serial I/O1, serial I/O2 clock output rising time
Serial I/O1, serial I/O2 clock output falling time
CMOS output rising time (Note 1)
CMOS output falling time (Note 1)
Limits
Min.
Typ.
Max.
tC(SCLK1)/2–30
tC(SCLK1)/2–30
140
–30
10
10
30
30
30
30
Typ.
Max.
Unit
ns
ns
ns
ns
ns
ns
ns
ns
Note 1: Pin XOUT is excluded.
Table 26 Switching characteristics (2)
(VCC = 2.4 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Symbol
tWH(SCLK1)
tWL(SCLK1)
td(SCLK1–TxD1)
tv(SCLK1–TxD1)
tr(SCLK1)
tf(SCLK1)
tr(CMOS)
tf(CMOS)
Parameter
Serial I/O1, serial I/O2 clock output “H” pulse width
Serial I/O1, serial I/O2 clock output “L” pulse width
Serial I/O1, serial I/O2 output delay time
Serial I/O1, serial I/O2 output valid time
Serial I/O1, serial I/O2 clock output rising time
Serial I/O1, serial I/O2 clock output falling time
CMOS output rising time (Note 1)
CMOS output falling time (Note 1)
Limits
Min.
tC(SCLK1)/2–50
tC(SCLK1)/2–50
350
–30
20
20
50
50
50
50
Typ.
Max.
Unit
ns
ns
ns
ns
ns
ns
ns
ns
Note 1: Pin XOUT is excluded.
Table 27 Switching characteristics (3)
(VCC = 2.2 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Symbol
tWH(SCLK1)
tWL(SCLK1)
td(SCLK1–TxD1)
tv(SCLK1–TxD1)
tr(SCLK1)
tf(SCLK1)
tr(CMOS)
tf(CMOS)
Parameter
Serial I/O1, serial I/O2 clock output “H” pulse width
Serial I/O1, serial I/O2 clock output “L” pulse width
Serial I/O1, serial I/O2 output delay time
Serial I/O1, serial I/O2 output valid time
Serial I/O1, serial I/O2 clock output rising time
Serial I/O1, serial I/O2 clock output falling time
CMOS output rising time (Note 1)
CMOS output falling time (Note 1)
Note 1: Pin XOUT is excluded.
Measured
output pin
100 pF
///
CMOS output
Fig. 95 Switching characteristics measurement circuit diagram
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 80 of 93
Limits
Min.
tC(SCLK1)/2–70
tC(SCLK1)/2–70
450
–30
25
25
70
70
70
70
Unit
ns
ns
ns
ns
ns
ns
ns
ns
7546 Group
tC(CNTR0)
tWL(CNTR0)
tWH(CNTR0)
0.8VCC
CNTR0
0.2VCC
tWL(INT0)
tWH(INT0)
INT0, INT1
CAP0, CAP1
0.8VCC
0.2VCC
tW(RESET)
RESET
0.8
VCC
0.2VCC
tC(XIN)
tWL(XIN)
tWH(XIN)
0.8VCC
XIN
0.2VCC
tC(SCLK1)
tf
SCLK1
tWL(SCLK1)
tWH(SCLK1)
0.8VCC
0.2VCC
tsu(RxD1-SCLK1)
th(SCLK1-RxD1)
0.8VCC
0.2
VCC
RXD1 (at receive)
td(SCLK1-TxD1)
TXD1 (at transmit)
Fig. 95 Timing chart
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
tr
page 81 of 93
tv(SCLK1-TxD1)
7546 Group
PACKAGE OUTLINE
JEITA Package Code
RENESAS Code
Previous Code
MASS[Typ.]
P-LQFP32-7x7-0.80
PLQP0032GB-A
32P6U-A
0.2g
HD
*1
D
24
17
NOTE)
1. DIMENSIONS "*1" AND "*2"
DO NOT INCLUDE MOLD FLASH.
2. DIMENSION "*3" DOES NOT
INCLUDE TRIM OFFSET.
16
25
bp
c
c1
HE
*2
E
b1
Reference
Symbol
Terminal cross section
32
1
ZE
9
Nom
D
6.9
7.0
7.1
E
6.9
7.0
7.1
A2
8
ZD
Dimension in Millimeters
Min
1.4
HD
8.8
9.0
9.2
HE
8.8
9.0
9.2
A1
0
0.1
0.2
bp
0.32
0.37
0.42
0.09
0.145
A
c
A
F
A2
Index mark
A1
1.7
0.35
b1
c
L
0°
e
y
*3
e
bp
x
x
0.20
y
0.10
0.7
0.7
ZE
L
0.3
Previous Code
MASS[Typ.]
PRDP0032BA-A
32P4B
2.2g
17
1
16
D
L
A1
A
A2
*2
c
*1
E
32
0.7
e1
RENESAS Code
0.5
1.0
L1
JEITA Package Code
8°
0.8
ZD
P-SDIP32-8.9x28-1.78
0.20
0.125
c1
L1
Detail F
Max
NOTE)
1. DIMENSIONS "*1" AND "*2"
DO NOT INCLUDE MOLD FLASH.
2. DIMENSION "*3" DOES NOT
INCLUDE TRIM OFFSET.
Reference
Symbol
Dimension in Millimeters
Min
Nom
Max
e1
9.86
10.16
10.46
D
27.8
28.0
28.2
E
8.75
8.9
SEATING PLANE
e
*3 b
3
bp
*3
A1
b2
0.51
3.8
A2
bp
0.35
0.45
0.55
b2
0.63
0.73
1.03
b3
0.9
1.0
1.3
c
0.22
0.27
0.34
e
1.528
1.778
2.028
L
3.0
0°
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 82 of 93
9.05
5.08
A
15°
7546 Group
JEITA Package Code
RENESAS Code
Previous Code
MASS[Typ.]
P-HWQFN36-6x6-0.50
PWQN0036KA-A
36PJW-A
0.07g
D
27
19
28
27
19
18
28
18
E1
E
D2
Lp
10
36
10
9
1
36
9
1
e
bp
Reference
Symbol
F
Dimension in Millimeters
Min
Nom
D
5.9
6.0
6.1
E
5.9
6.0
6.1
x
A2
0.75
A
A2
A
0.8
A1
0
bp
0.15
e
Lp
A1
y
Detail F
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 83 of 93
Max
0
0.05
0.2
0.25
0.5
0.5
0.6
x
0.7
0.05
y
0.05
D2
4.26
E1
4.26
7546 Group
APPENDIX
NOTES ON PROGRAMMING
1. Processor Status Register
(1) Initializing of processor status register
Flags which affect program execution must be initialized after a reset.
In particular, it is essential to initialize the T and D flags because
they have an important effect on calculations.
<Reason>
After a reset, the contents of the processor status register (PS) are
undefined except for the I flag which is “1”.
Reset
↓
Initializing of flags
↓
Main program
Fig. 1 Initialization of processor status register
(2) How to reference the processor status register
To reference the contents of the processor status register (PS), execute the PHP instruction once then read the contents of (S+1). If
necessary, execute the PLP instruction to return the PS to its original status.
PLP instruction execution
Fig. 2 Sequence of PLP instruction execution
(S)
(S)+1
Set D flag to “1”
↓
ADC or SBC instruction
↓
NOP instruction
↓
SEC, CLC, or CLD instruction
Fig. 4 Status flag at decimal calculations
3. JMP instruction
When using the JMP instruction in indirect addressing mode, do
not specify the last address on a page as an indirect address.
4. Multiplication and Division Instructions
(1) The index X mode (T) and the decimal mode (D) flags do not
affect the MUL and DIV instruction.
(2) The execution of these instructions does not change the contents of the processor status register.
5. Read-modify-write instruction
Do not execute a read-modify-write instruction to the read invalid
address (SFR).
The read-modify-write instruction operates in the following sequence: read one-byte of data from memory, modify the data,
write the data back to original memory. The following instructions
are classified as the read-modify-write instructions in the 740
Family.
(1) Bit management instructions: CLB, SEB
(2) Shift and rotate instructions: ASL, LSR, ROL, ROR, RRF
(3) Add and subtract instructions: DEC, INC
(4) Logical operation instructions (1’s complement): COM
Stored PS
Fig. 3 Stack memory contents after PHP instruction execution
2. Decimal calculations
(1) Execution of decimal calculations
The ADC and SBC are the only instructions which will yield proper
decimal notation, set the decimal mode flag (D) to “1” with the
SED instruction. After executing the ADC or SBC instruction, execute another instruction before executing the SEC, CLC, or CLD
instruction.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
(2) Notes on status flag in decimal mode
When decimal mode is selected, the values of three of the flags in
the status register (the N, V, and Z flags) are invalid after a ADC or
SBC instruction is executed.
The carry flag (C) is set to “1” if a carry is generated as a result of
the calculation, or is cleared to “0” if a borrow is generated. To determine whether a calculation has generated a carry, the C flag
must be initialized to “0” before each calculation. To check for a
borrow, the C flag must be initialized to “1” before each calculation.
page 84 of 93
Add and subtract/logical operation instructions (ADC, SBC, AND,
EOR, and ORA) when T flag = “1” operate in the way as the readmodify-write instruction. Do not execute the read invalid SFR.
<Reason>
When the read-modify-write instruction is executed to read invalid
SFR, the instruction may cause the following consequence: the instruction reads unspecified data from the area due to the read
invalid condition. Then the instruction modifies this unspecified
data and writes the data to the area. The result will be random
data written to the area or some unexpected event.
7546 Group
NOTES ON PERIPHERAL FUNCTIONS
Notes on I/O Ports
1.Port direction register
• Set bits 6 and 7 of port P2 direction register to “1”.
• Set bits 5 and 6 of port P3 direction register to “1”.
2.Interrupt edge selection register
Set bit 2 of interrupt edge selection register to “1”.
3.Be sure to set bit 1 of port P1P3 control register (address 17 16)
to “0”.
4. Port P0P3 drive capacity control register
The number of LED drive port (drive capacity is HIGH) is 8.
5. Pull-up control register
When using each port which built in pull-up resistor as an output
port, the pull-up control bit of corresponding port becomes invalid,
and pull-up resistor is not connected.
<Reason>
Pull-up control is effective only when each direction register is set
to the input mode.
6. Notes in stand-by state
In stand-by state*1 for low-power dissipation, do not make input
levels of an input port and an I/O port “undefined”.
Pull-up (connect the port to Vcc) or pull-down (connect the port to
Vss) these ports through a resistor.
When determining a resistance value, note the following points:
• External circuit
• Variation of output levels during the ordinary operation
When using a built-in pull-up resistor, note on varied current values:
• When setting as an input port : Fix its input level
• When setting as an output port : Prevent current from flowing out
to external.
<Reason>
The output transistor becomes the OFF state, which causes the
ports to be the high-impedance state. Note that the level becomes
“undefined” depending on external circuits.
Accordingly, the potential which is input to the input buffer in a microcomputer is unstable in the state that input levels of an input
port and an I/O port are “undefined”. This may cause power
source current.
*1 stand-by state : the stop mode by executing the STP instruction
the wait mode by executing the WIT instruction
7. Modifying output data with bit managing instruction
When the port latch of an I/O port is modified with the bit managing instruction*2, the value of the unspecified bit may be changed.
<Reason>
The bit managing instructions are read-modify-write form instructions for reading and writing data by a byte unit. Accordingly, when
these instructions are executed on a bit of the port latch of an I/O
port, the following is executed to all bits of the port latch.
• As for a bit which is set for an input port :
The pin state is read in the CPU, and is written to this bit after bit
managing.
• As for a bit which is set for an output port :
The bit value of the port latch is read in the CPU, and is written to
this bit after bit managing.
Note the following :
• Even when a port which is set as an output port is changed for
an input port, its port latch holds the output data.
• As for a bit of the port latch which is set for an input port, its
value may be changed even when not specified with a bit managing instruction in case where the pin state differs from its port
latch contents.
*2 bit managing instructions : SEB, and CLB instructions
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 85 of 93
7546 Group
8. Direction register
The values of the port direction registers cannot be read.
That is, it is impossible to use the LDA instruction, memory operation instruction when the T flag is “1”, addressing mode using
direction register values as qualifiers, and bit test instructions such
as BBC and BBS.
It is also impossible to use bit operation instructions such as CLB
and SEB and read-modify-write instructions of direction registers
for calculations such as ROR.
For setting direction registers, use the LDM instruction, STA instruction, etc.
Termination of Unused Pins
1. Terminate unused pins
Perform the following wiring at the shortest possible distance (20
mm or less) from microcomputer pins.
(1) I/O ports
Set the I/O ports for the input mode and connect each pin to VCC
or VSS through each resistor of 1 kΩ to 10 kΩ. The port which can
select a built-in pull-up resistor can also use the built-in pull-up resistor.
When using the I/O ports as the output mode, open them at “L” or
“H”.
• When opening them in the output mode, the input mode of the
initial status remains until the mode of the ports is switched over
to the output mode by the program after reset. Thus, the potential at these pins is undefined and the power source current may
increase in the input mode. With regard to an effects on the system, thoroughly perform system evaluation on the user side.
• Since the direction register setup may be changed because of a
program runaway or noise, set direction registers by program
periodically to increase the reliability of program.
2. Termination remarks
(1) I/O ports setting as input mode
[1] Do not open in the input mode.
<Reason>
• The power source current may increase depending on the firststage circuit.
• An effect due to noise may be easily produced as compared with
proper termination (1) shown on the above “1. Terminate unused
pins”.
[2] Do not connect to VCC or VSS directly.
<Reason>
If the direction register setup changes for the output mode because of a program runaway or noise, a short circuit may occur.
[3] Do not connect multiple ports in a lump to VCC or VSS through
a resistor.
<Reason>
If the direction register setup changes for the output mode because of a program runaway or noise, a short circuit may occur
between ports.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 86 of 93
Notes on Interrupts
1. Change of relevant register settings
When not requiring for the interrupt occurrence synchronous with
the following case, take the sequence shown in Figure 5.
• When switching external interrupt active edge
• When switching interrupt sources of an interrupt vector address
where two or more interrupt sources are allocated
Set the corresponding interrupt enable bit to “0” (disabled) .
↓
Set the interrupt edge selection bit, active edge switch bit, or
the interrupt source selection bit.
↓
NOP (One or more instructions)
↓
Set the corresponding interrupt request bit to “0”
(no interrupt request issued).
↓
Set the corresponding interrupt enable bit to “1” (enabled).
Fig. 5 Sequence of changing relevant register
<Reason>
When setting the followings, the interrupt request bit of the corresponding interrupt may be set to “1”.
• When switching external interrupt active edge
INT0 interrupt edge selection bit
(bit 0 of Interrupt edge selection register (address 3A16))
INT1 interrupt edge selection bit
(bit 1 of Interrupt edge selection register)
CNTR0 active edge switch bit
(bit 2 of timer X mode register (address 2B16))
Capture 0 interrupt edge selection bit
(bits 1 and 0 of capture mode register (address 2016))
Capture 1 interrupt edge selection bit
(bits 3 and 2 of capture mode register)
2. Check of interrupt request bit
When executing the BBC or BBS instruction to determine an interrupt request bit immediately after this bit is set to “0”, take the
following sequence.
<Reason>
If the BBC or BBS instruction is executed immediately after an interrupt request bit is cleared to “0”, the value of the interrupt
request bit before being cleared to “0” is read.
Set the interrupt request bit to “0” (no interrupt issued)
↓
NOP (one or more instructions)
↓
Execute the BBC or BBS instruction
Fig. 6 Sequence of check of interrupt request bit
7546 Group
3. Interrupt discrimination bit
Use an LDM instruction to clear to “0” an interrupt discrimination
bit.
LDM #%0000XXXX, $0B
Set the following values to “X”
“0”: an interrupt discrimination bit to clear
“1”: other interrupt discrimination bits
Ex.) When a key-on wakeup interrupt discrimination bit is cleared;
LDM #%00001110 and $0B.
4. Interrupt discrimination bit and interrupt request bit
For key-on wakeup, UART1 bus collision detection, A/D conversion and Timer 1 interrupt, even if each interrupt valid bit (interrupt
source set register (address 0A16)) is set “0: Invalid”, each interrupt discrimination bit (interrupt source discrimination register
(address 0B16)) is set to “1: interrupt occurs” when corresponding
interrupt request occurs.
But corresponding interrupt request bit (interrupt request registers
1, 2 (addresses 3C16, 3D16) is not affected.
Notes on Timers
1. When n (0 to 255) is written to a timer latch, the frequency division ratio is 1/(n+1).
2. When a count source of timer X, timer A or timer B is switched,
stop a count of the timer.
Notes on Timer X
1. CNTR0 interrupt active edge selection
CNTR0 interrupt active edge depends on the CNTR0 active edge
switch bit (bit 2 of timer X mode register (address 2B16)).
When this bit is “0”, the CNTR0 interrupt request bit is set to “1” at
the falling edge of CNTR0 pin input signal. When this bit is “1”, the
CNTR0 interrupt request bit is set to “1” at the rising edge of
CNTR0 pin input signal.
2. Timer X count source selection
The f(XIN) (frequency not divided) can be selected by the timer X
count source selection bits (bits 1 and 0 of timer count source set
register (address 2A16)) only when the ceramic oscillation or the
on-chip oscillator is selected.
Do not select it for the timer X count source at the RC oscillation.
3. Pulse output mode
Set the direction register of port P14, which is also used as CNTR0
pin, to output.
When the TXOUT pin is used, set the direction register of port P03,
which is also used as TXOUT pin, to output.
4. Pulse width measurement mode
Set the direction register of port P14, which is also used as CNTR0
pin, to input.
Notes on Timer A, B
1. Setting of timer value
When “1: Write to only latch” is set to the timer A (B) write control
bit (bit 0 (bit 2) of timer X mode register (address 1D16)), written
data to timer register is set to only latch even if timer is stopped or
operating. Accordingly, in order to set the initial value for timer
when it is stopped, set “0: Write to latch and timer simultaneously”
to timer A (B) write control bit.
2. Read/write of timer A
Stop timer A to read/write its data in the following state;
XIN oscillation selected by clock division ratio selection bits (bits 7
and 6 of CPU mode register (address 3B16)), and the on-chip oscillator output is selected as the timer A count source.
3. Read/write of timer B
Stop timer B to read/write its data in the following state;
XIN oscillation selected by clock division ratio selection bits, the
timer A underflow is selected as the timer B count source, and the
on-chip oscillator output is selected as the timer A count source.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 87 of 93
7546 Group
Notes on Output Compare
Notes on Input Capture
1. When the selected source timer of each compare channel is
stopped, written data to compare register is loaded to the compare latch simultaneously.
1. If the capture trigger is input while the capture register (low-order and high-order) is in read, captured value is changed
between high-order reading and low-order reading. Accordingly,
some countermeasure by program is recommended, for example comparing the values that twice of read.
2. Do not write the same data to both of compare latch x0 (x=0, 1,
2, 3) and x1.
3. When setting value of the compare register is larger than timer
setting value, compare match signal is not generated. Accordingly, the output waveform is fixed to “L” or “H” level.
However, when setting value of another compare register is
smaller than timer setting value, this compare match signal is
generated. Accordingly, if the corresponding compare latch y
(y=00, 01, 10, 11, 20, 21, 30, 31) interrupt source bit is set to “1”
(valid), compare match interrupt request occurs.
4. When the compare x trigger enable bit is cleared to “0” (disabled), the match trigger to the waveform output circuit is
disabled. Accordingly, the output waveform can be fixed to “L”
or “H” level.
However, in this case, the compare match signal is generated.
Accordingly, if the corresponding compare latch y (y=00, 01, 10,
11, 20, 21, 30, 31) interrupt source bit is set to “1”
(valid),compare match interrupt request occurs.
2. Timer A cannot be used for the capture source timer in the following state;
• XIN oscillation selected by clock division ratio selection bits
(bits 7 and 6 of CPU mode register (address 3B16))
• Timer A count source: On-chip oscillator output.
Timer B cannot be used for the capture source timer in the following state;
• XIN oscillation selected by clock division ratio selection bits
• Timer B count source: Timer A underflow
• Timer A count source: On-chip oscillator output.
3. As shown below, when the capture input is performed to both
capture latch 00 and 01 at the same time, the value of capture
0 status bit (bit 4 of capture/compare status register (address
2216)) is undefined (same as capture 1).
• When “1” is written to capture latch 00 software trigger bit (bit 0
of capture software trigger register (address 1316)) and capture
latch 01 software trigger bit (bit 1 of capture software trigger register) at the same time
• When external trigger of capture latch 00 and software trigger of
capture latch 01 occur at the same time
• When external trigger of capture latch 01 and software trigger of
capture latch 00 occur at the same time
4. When the capture interrupt is used as the interrupt for return
from stop mode, set the capture 0 noise filter clock selection
bits (bits 5 and 4 of capture mode register (address 2016)) to
“00 (Filter stop)” (same as capture 1).
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 88 of 93
7546 Group
Notes on Serial I/Oi (i=1, 2)
1. Clock synchronous serial I/O
(1) When the transmit operation is stopped, clear the serial I/Oi
enable bit and the transmit enable bit to “0” (serial I/Oi and
transmit disabled).
<Reason>
Since transmission is not stopped and the transmission circuit is
not initialized even if only the serial I/Oi enable bit is cleared to “0”
(serial I/Oi disabled), the internal transmission is running (in this
case, since pins TxD i , RxD i , S CLKi , and S RDYi function as I/O
ports, the transmission data is not output). When data is written to
the transmit buffer register in this state, data starts to be shifted to
the transmit shift register. When the serial I/Oi enable bit is set to
“1” at this time, the data during internally shifting is output to the
TxDi pin and an operation failure occurs.
3. Notes common to clock synchronous serial I/O and UART
(1) Set the serial I/Oi (i=1, 2) control register again after the transmission and the reception circuits are reset by clearing both
the transmit enable bit and the receive enable bit to “0.”
Clear both the transmit enable bit (TE)
and the receive enable bit (RE) to “0”
Set the bits 0 to 3 and bit 6 of the
serial I/Oi control register
Set both the transmit enable bit (TE)
and the receive enable bit (RE), or
one of them to “1”
Can be set
with the LDM
instruction at
the same time
Fig. 7 Sequence of setting serial I/Oi control register again
(2) When the receive operation is stopped, clear the receive enable bit to “0” (receive disabled), or clear the serial I/Oi enable
bit to “0” (serial I/Oi disabled).
(3) When the transmit/receive operation is stopped, clear both the
transmit enable bit and receive enable bit to “0” (transmit and
receive disabled) simultaneously. (any one of data transmission and reception cannot be stopped.)
<Reason>
In the clock synchronous serial I/O mode, the same clock is used
for transmission and reception.
If any one of transmission and reception is disabled, a bit error occurs because transmission and reception cannot be synchronized.
In this mode, the clock circuit of the transmission circuit also operates for data reception. Accordingly, the transmission circuit does
not stop by clearing only the transmit enable bit to “0” (transmit
disabled). Also, the transmission circuit cannot be initialized even
if the serial I/Oi enable bit is cleared to “0” (serial I/Oi disabled)
(same as (1)).
(4) When signals are output from the S RDYi pin on the reception
side by using an external clock, set all of the receive enable
bit, the SRDYi output enable bit, and the transmit enable bit to
“1”.
(5) When the SRDYi signal input is used, set the using pin to the input mode before data is written to the transmit/receive buffer
register.
2. UART
When the transmit operation is stopped, clear the transmit enable
bit to “0” (transmit disabled).
<Reason>
Same as (1) shown on the above “1. Clock synchronous serial I/O“.
When the receive operation is stopped, clear the receive enable
bit to “0” (receive disabled).
When the transmit/receive operation is stopped, clear the transmit
enable bit to “0” (transmit disabled) and receive enable bit to “0”
(receive disabled).
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 89 of 93
(2) The transmit shift completion flag changes from “1” to “0” with
a delay of 0.5 to 1.5 shift clocks. When data transmission is
controlled with referring to the flag after writing the data to the
transmit buffer register, note the delay.
(3) When data transmission is executed at the state that an external clock input is selected as the synchronous clock, set “1” to
the transmit enable bit while the SCLKi is “H” state. Also, write
to the transmit buffer register while the SCLKi is “H” state.
(4) When the transmit interrupt is used, set as the following sequence.
➀ Serial I/Oi transmit interrupt enable bit is set to “0” (disabled).
➁ Serial I/Oi transmit enable bit is set to “1”.
➂ Serial I/Oi transmit interrupt request bit is set to “0” after 1 or
more instructions have been executed.
➃ Serial I/Oi transmit interrupt enable bit is set to “1” (enabled).
<Reason>
When the transmit enable bit is set to “1”, the transmit buffer
empty flag and transmit shift completion flag are set to “1”.
Accordingly, even if the timing when any of the above flags is set
to “1” is selected for the transmit interrupt source, interrupt request
occurs and the transmit interrupt request bit is set.
(5) Write to the baud rate generator (BRGi) while the transmit/receive operation is stopped.
7546 Group
Notes on Serial I/O1
Notes on Serial I/O2
1. I/O pin function when serial I/O1 is enabled.
The pin functions of P12/SCLK1 and P13/SRDY1 are switched to as
follows according to the setting values of a serial I/O1 mode selection bit (bit 6 of serial I/O1 control register (address 1A16)) and a
serial I/O1 synchronous clock selection bit (bit 1 of serial I/O1 control register).
(1) Serial I/O1 mode selection bit → “1” :
Clock synchronous type serial I/O is selected.
• Setup of a serial I/O1 synchronous clock selection bit
“0” : P12 pin turns into an output pin of a synchronous clock.
“1” : P12 pin turns into an input pin of a synchronous clock.
• Setup of a SRDY1 output enable bit (SRDY)
“0” : P13 pin can be used as a normal I/O pin.
“1” : P13 pin turns into a SRDY1 output pin.
1. I/O pin function when serial I/O2 is enabled
The pin functions of P06/SCLK2 and P07/SRDY2 are switched to as
follows according to the setting values of a serial I/O2 mode selection bit (bit 6 of serial I/O2 control register (address 3016)) and a
serial I/O2 synchronous clock selection bit (bit 2 of serial I/O2 control register).
(2) Serial I/O1 mode selection bit → “0” :
Clock asynchronous (UART) type serial I/O is selected.
• Setup of a serial I/O1 synchronous clock selection bit
“0”: P12 pin can be used as a normal I/O pin.
“1”: P12 pin turns into an input pin of an external clock.
• When clock asynchronous (UART) type serial I/O is selected, it
functions P13 pin. It can be used as a normal I/O pin.
Note on Bus Collision Detection
When serial I/O1 is operating at half-duplex communication, set
bus collision detection interrupt to be disabled.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 90 of 93
(1) Serial I/O2 mode selection bit → “1” :
Clock synchronous type serial I/O is selected.
• Setup of a serial I/O2 synchronous clock selection bit
“0” : P06 pin turns into an output pin of a synchronous clock.
“1” : P06 pin turns into an input pin of a synchronous clock.
• Setup of a SRDY2 output enable bit (SRDY)
“0” : P07 pin can be used as a normal I/O pin.
“1” : P07 pin turns into a SRDY2 output pin.
(2) Serial I/O2 mode selection bit → “0” :
Clock asynchronous (UART) type serial I/O is selected.
• Setup of a serial I/O2 synchronous clock selection bit
“0”: P06 pin can be used as a normal I/O pin.
“1”: P06 pin turns into an input pin of an external clock.
• When clock asynchronous (UART) type serial I/O is selected, it
functions P07 pin. It can be used as a normal I/O pin.
7546 Group
Notes on A/D conversion
1. Analog input pin
Make the signal source impedance for analog input low, or equip
an analog input pin with an external capacitor of 0.01µF to 1µF.
Further, be sure to verify the operation of application products on
the user side.
<Reason>
An analog input pin includes the capacitor for analog voltage comparison. Accordingly, when signals from signal source with high
impedance are input to an analog input pin, charge and discharge
noise generates. This may cause the A/D conversion/comparison
precision to be worse.
2. Clock frequency during A/D conversion
The comparator consists of a capacity coupling, and a charge of
the capacity will be lost if the clock frequency is too low. This may
cause the A/D conversion precision to be worse. Accordingly, set
f(XIN ) in order that the A/D conversion clock is 250 kHz or over
during A/D conversion.
3. A/D conversion clock selection
Select f(XIN)/2 as an A/D conversion clock by setting the A/D conversion clock selection bit (bit 3 of A/D control register (address
3416)) when RC oscillation is used.
The f(XIN) can be also used as an A/D conversion clock only when
ceramic oscillation or on-chip oscillator is used.
4. Read A/D conversion register
• 8-bit read
Read only the A/D conversion low-order register (address 3516).
•10-bit read
Read the A/D conversion high-ordrer register (address 3616) first,
and then, read the A/D conversion low-order register (address
3516).
In this case, the high-order 6 bits of address 36 16 returns “0”
when read.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 91 of 93
5. A/D conversion accuracy
As for AD translation accuracy, on the following operating conditions, accuracy may become low.
(1) Since the analog circuit inside a microcomputer becomes sensitive to noise when V REF voltage is set up lower than Vcc
voltage, accuracy may become low rather than the case
where VREF voltage and Vcc voltage are set up to the same
value..
(2) When VREF voltage is lower than [ 3.0 V ], the accuracy at the
low temperature may become extremely low compared with
that at room temperature. When the system would be used at
low temperature, the use at V REF =3.0 V or more is recommended.
Notes on Watchdog Timer
1. The watchdog timer is operating during the wait mode. Write
data to the watchdog timer control register to prevent timer underflow.
2. The watchdog timer stops during the stop mode. However, the
watchdog timer is running during the oscillation stabilizing time
after the STP instruction is released. In order to avoid the underflow of the watchdog timer, the watchdog timer count source
selection bit (bit 7 of watchdog timer control register (address
3916)) before executing the STP instruction.
3. The STP instruction function selection bit (bit 6 of watchdog
timer control register (address 3916)) can be rewritten only once
after releasing reset. After rewriting it is disable to write any
data to this bit.
Notes on RESET pin
1. Connecting capacitor
In case where the RESET signal rise time is long, connect a ceramic capacitor or others across the RESET pin and the Vss pin.
And use a 1000 pF or more capacitor for high frequency use.
When connecting the capacitor, note the following :
• Make the length of the wiring which is connected to a capacitor
as short as possible.
• Be sure to verify the operation of application products on the
user side.
<Reason>
If the several nanosecond or several ten nanosecond impulse
noise enters the RESET pin, it may cause a microcomputer failure.
7546 Group
Notes on Clock Generating Circuit
1. Switch of ceramic and RC oscillations
After releasing reset, the oscillation mode selection bit (bit 5 of
CPU mode register (address 3B16)) is “0” (ceramic oscillation selected). When the RC oscillation is used, after releasing reset, set
this bit to “1”.
2. Double-speed mode
The double-speed mode can be used only when a ceramic oscillation is selected. Do not use it when an RC oscillation is selected.
3. CPU mode register
Oscillation mode selection bit (bit 5), processor mode bits (bits 1
and 0) of CPU mode register (address 3B16) are used to select oscillation mode and to control operation modes of the
microcomputer. In order to prevent the dead-lock by erroneously
writing (ex. program run-away), these bits can be rewritten only
once after releasing reset. After rewriting, it is disabled to write any
data to the bit. (The emulator MCU “M37542RSS” is excluded.)
Also, when the read-modify-write instructions (SEB, CLB, etc.) are
executed to bits 2 to 4, 6 and 7, bits 5, 1 and 0 are locked.
4. Clock division ratio, X IN oscillation control, on-chip oscillator
control
The state transition shown in Fig. 78 can be performed by setting
the clock division ratio selection bits (bits 7 and 6), XIN oscillation
control bit (bit 4), on-chip oscillator oscillation control bit (bit 3) of
CPU mode register. Be careful of notes on use in Fig. 78.
5. On-chip oscillator operation
When the MCU operates by the on-chip oscillator for the main
clock, connect XIN pin to VCC through a 1 kΩ to 10 kΩ resistor and
leave XOUT pin open.
The clock frequency of the on-chip oscillator depends on the supply voltage and the operation temperature range.
Be careful that this margin of frequencies when designing application products.
6. Ceramic resonator
When the ceramic resonator is used for the main clock, connect
the ceramic resonator and the external circuit to pins XIN and
XOUT at the shortest distance. Externally connect a damping resistor Rd depending on the oscillation frequency. A feedback resistor
is built-in.
Use the resonator manufacturer’s recommended value because
constants such as capacitance depend on the resonator.
7. RC oscillation
When the RC oscillation is used for the main clock, connect the
XIN pin and XOUT pin to the external circuit of resistor R and the
capacitor C at the shortest distance.
The frequency is affected by a capacitor, a resistor and a microcomputer.
So, set the constants within the range of the frequency limits.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 92 of 93
8. External clock
When the external signal clock is used for the main clock, connect
the XIN pin to the clock source and leave XOUT pin open.
Select “0” (ceramic oscillation) to oscillation mode selection bit.
9. Count source (Timer 1, Timer A, Timer B, Timer X, Serial I/O,
Serial I/O2, A/D converter, Watchdog timer)
The count sources of these functions are affected by the clock division selection bit of the CPU mode register.
The f(XIN) clock is supplied to the watchdog timer when selecting
f(XIN) as the CPU clock.
The on-chip oscillator output is supplied to these functions when
selecting the on-chip oscillator output as the CPU clock.
However, the watchdog timer is also affected by the function set
ROM.
Notes on Oscillation Control
1. Oscillation stop detection circuit
(1) When the stop mode is used, set the oscillation stop detection
function to “invalid”.
(2) When the ceramic or RC oscillation is stopped by the XIN oscillation control bit (bit 4 of CPU mode register (address 3B16)),
set the oscillation stop detection function to “invalid”.
2. Stop mode
(1) When the stop mode is used, set the oscillation stop detection
function to “invalid”.
(2) When the stop mode is used, set “0” (STP instruction enabled)
to the STP instruction function selection bit of the watchdog
timer control register (bit 6 of watchdog timer control register
(address 3916)).
(3) The oscillation stabilizing time after release of STP instruction
can be selected from “set automatically ”/“not set automatically” by the oscillation stabilizing time set bit after release of
the STP instruction (bit 0 of MISRG (address 3816)). When “0”
is set to this bit, “01 16” is set to timer 1 and “FF16 ” is set to
prescaler 1 automatically at the execution of the STP instruction. When “1” is set to this bit, set the wait time to timer 1 and
prescaler 1 according to the oscillation stabilizing time of the
oscillation. Also, when timer 1 is used, set values again to
timer 1 and prescaler 1 after system is returned from the stop
mode.
(4) Do not execute the STP instruction during the A/D conversion.
7546 Group
Notes on On-chip Oscillation Division Ratio
• When the clock division ratio is switched from f(XIN) to on-chip
oscillator by the clock division ratio selection bits (bits 7 and 6 of
CPU mode register (address 3B16)), the on-chip oscillator division ratio (bits 1 and 0 of on-chip oscillation division ratio
selection register (address 37 16)) is “10 2 ” (on-chip oscillator
middle-speed mode (ROSC/8)).
Notes on Oscillation Stop Detection Circuit
1. After the reset by the oscillation stop detection, the value of following bits are retained, not initialized.
• Ceramic or RC oscillation stop detection function active bit
Bit 1 of MISRG (address 3B16)
• Oscillation stop detection status bit
Bit 3 of MISRG
2. Oscillation stop detection status bit is initialized (“0”) by the following operation.
• External reset
• Write “0” data to the ceramic or RC oscillation stop detection
function active bit.
3. The oscillation stop detection circuit is not included in the emulator MCU “M37542RSS”.
Note on Power Source Voltage
When the power source voltage value of a microcomputer is less
than the value which is indicated as the recommended operating
conditions, the microcomputer does not operate normally and may
perform unstable operation.
In a system where the power source voltage drops slowly when
the power source voltage drops or the power supply is turned off,
reset a microcomputer when the supply voltage is less than the
recommended operating conditions and design a system not to
cause errors to the system by this unstable operation.
NOTES ON HARDWARE
Handling of Power Source Pin
In order to avoid a latch-up occurrence, connect a capacitor suitable for high frequencies as bypass capacitor between power
source pin (Vcc pin) and GND pin (Vss pin). Besides, connect the
capacitor to as close as possible. For bypass capacitor which
should not be located too far from the pins to be connected, a ceramic capacitor of 0.01 µF to 0.1 µF is recommended.
NOTES ON QzROM
Notes On QzROM Writing Orders
When ordering the QzROM product shipped after writing, submit
the mask file (extension: .mask) which is made by the mask file
converter MM.
Be sure to set the ROM option ("MASK option" written in the mask
file converter) setup when making the mask file by using the mask
file converter MM.
Notes On ROM Code Protect
(QzROM product shipped after writing)
As for the QzROM product shipped after writing, the ROM code
protect is specified according to the ROM option setup data in the
mask file which is submitted at ordering.
Renesas Technology corp. write the value of the ROM option
setup data in the ROM code protect address (address FFDB 16)
when writing to the QzROM. As a result, in the contents of the
ROM code protect address the ordered value may differ from the
actual written value.
The ROM option setup data in the mask file is “0016” for protect
enabled or “FF16” for protect disabled. Therefore, the contents of
the ROM code protect address (other than the user ROM area) of
the QzROM product shipped after writing is “0016” or “FF16”.
Note that the mask file which has nothing at the ROM option data
or has the data other than “0016” and “FF16” can not be accepted.
Product shipped in blank
As for the product shipped in blank, Renesas does not perform the
writing test to user ROM area after the assembly process though
the QzROM writing test is performed enough before the assembly
process. Therefore, a writing error of approx.0.1 % may occur.
Moreover, please note the contact of cables and foreign bodies on
a socket, etc. because a writing environment may cause some
writing errors.
Rev.1.21 Nov 15, 2006
REJ03B0160-0121
page 93 of 93
DATA REQUIRED FOR QzROM WRITING
ORDERS
The following are necessary when ordering a QzROM product
shipped after writing:
1. QzROM Writing Confirmation Form*
2. Mark Specification Form*
3. ROM data...........Mask file
* For the QzROM writing confirmation form and the mark specification form, refer to the “Renesas Technology Corp.” Homepage
(http://www.renesas.com/homepage.jsp).
Note that we cannot deal with special font marking (customer's
trademark etc.) in QzROM microcomputer.
7546 Group Datasheet
REVISION HISTORY
Rev.
Date
Description
Summary
Page
1.00 Oct 14, 2005
1.10 Jun 05, 2006
–
–
1
2, 3
4
9
22
39
41
56
62
67
74
75
76
1.20 Aug 30, 2006
77
78, 79
80
81
84
9
54, 91
59, 92
70
75
77
1.21 Nov 15, 2006
91
73
First Edition issued
“Preliminary” eliminated.
Power dissipation added.
Fig.1, Fig.2 and Fig.3: part numbers added.
Power source voltage (at on-chip oscillator) and power dissipation added.
Memory expansion plan: “Under development” eliminated.
Notes on use (2): $0Bn → $0B
Notes on Input Capture; 2nd note: some description added.
Block diagram of capture channel 0: address of capture pointer revised.
Low Voltage Detection Circuit: bit number of the function set ROM data 0 revised.
State transition: (4) revised.
Wiring for the VPP pin of the QzPROM revised.
Electrical characteristics (1) VRAM Min. value is added.
Electrical characteristics (2)
- Parameter
The condition is added.
- Limits
Typ. and Max. values are changed.
A/D Converter characteristics
- Absolute accuracy
Max. value is revised.
Power-on reset circuit characteristics and Low voltage detection circuit added.
Timing requirements is added.
Switching characteristics is added.
Timing chart added.
BRK instruction eliminated.
Table 3: ROM size revised and note added.
Notes on watchdog timer: note 3 revised.
Notes on clock generating circuit: note added.
5. Setup for I/O ports: Note eliminated.
Electrical characteristics (2)
- Low voltage detection circuit self consumption current added.
Low voltage detection circuit characteristics.
- Unit of VLVD
mV → V
(1) Analog input pin: description revised.
All f(XIN): VCC condition added.
A-1
Sales Strategic Planning Div.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Notes:
1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes
warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property
rights or any other rights of Renesas or any third party with respect to the information in this document.
2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including,
but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples.
3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass
destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws
and regulations, and procedures required by such laws and regulations.
4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this
document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document,
please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be
disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com )
5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a
result of errors or omissions in the information included in this document.
6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability
of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular
application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products.
7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications
or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality
and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or
undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall
have no liability for damages arising out of the uses set forth above.
8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below:
(1) artificial life support devices or systems
(2) surgical implantations
(3) healthcare intervention (e.g., excision, administration of medication, etc.)
(4) any other purposes that pose a direct threat to human life
Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing
applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all
damages arising out of such applications.
9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range,
movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages
arising out of the use of Renesas products beyond such specified ranges.
10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain
rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage
caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and
malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software
alone is very difficult, please evaluate the safety of the final products or system manufactured by you.
11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as
swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products.
Renesas shall have no liability for damages arising out of such detachment.
12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas.
13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have
any other inquiries.
http://www.renesas.com
RENESAS SALES OFFICES
Refer to "http://www.renesas.com/en/network" for the latest and detailed information.
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501
Renesas Technology Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900
Renesas Technology (Shanghai) Co., Ltd.
Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120
Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898
Renesas Technology Hong Kong Ltd.
7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2730-6071
Renesas Technology Taiwan Co., Ltd.
10th Floor, No.99, Fushing North Road, Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999
Renesas Technology Singapore Pte. Ltd.
1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
Renesas Technology Korea Co., Ltd.
Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea
Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145
Renesas Technology Malaysia Sdn. Bhd
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: <603> 7955-9390, Fax: <603> 7955-9510
© 2006. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .7.0
Similar pages