ON LB1973JA-AH Two-channel h-bridge driver Datasheet

Ordering number : ENA2014
LB1973JA
Monolithic Digital IC
Two-channel H-Bridge Driver
http://onsemi.com
Overview
The LB1973JA is a two-channel H-bridge driver that supports for low saturation draive operation. It is optimal for
H-bridge drive of stepping motors (AF and zoom) in portable equipment such as camera cell phones.
Features
• Two-channel H-bridge driver
• 2ch simultaneous connection is possible
• Parallel input interface
• 2 phase excitation, 1-2 phase excitation drive are possible
• The range of the operation voltage is wide.(1.8V to 7.5V)
• Built-in thermal protection
Specifications
Absolute Maximum Ratings at Ta = 25°C
Parameter
Maximum supply voltage
Output voltage
Symbol
Conditions
VCC max
VOUT max
Ratings
Unit
-0.3 to +8.0
V
- VSF to VCC+VSF
V
Input voltage
VIN max
-0.3 to +8.0
Spark killer Di order direction electric
ISF max
1000
Ground pin source current
Allowable power dissipation
IGND
Per channel
Pd max
*Mounted on a bord
V
mA
1000
mA
800
mW
Operating temperature
Topr
-20 to +85
°C
Storage temperature
Tstg
-40 to +150
°C
* Mounted on a Specified board : 114.3mm×76.1mm×1.6mm, glass epoxy
Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time.
Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current,
high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details.
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating
Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
Allowable Operating Ratings at Ta = 25°C
Parameter
Symbol
Conditions
Ratings
Unit
Supply voltage
VCC
High-level input voltage
VIH
RIN = 1kΩ
1.3 to 7.5
V
Low-level input voltage
VIL
RIN = 1kΩ
-0.3 to +0.5
V
Semiconductor Components Industries, LLC, 2013
June, 2013
1.8 to 7.5
V
30712 SY 20120117-S00010 No.A2014-1/5
LB1973JA
Electrical Characteristics at Ta = 25°C, VCC = 1.9V
Parameter
Source current
Output saturation voltage1
Symbol
Conditions
Ratings
min
typ
Unit
max
ICCO1
VCC = 1.9V,IN1 to IN4 = Low level
0.01
1
μA
ICCO2
VCC = 3V,IN1 to IN4 = Low level
0.01
1
μA
ICC1
IN1 = High level,IN2 to IN4 = Low level
18
25
mA
ICC2
IN1 = High level,IN2 to IN4 = Low level,
VCC = 3V
19
27.5
mA
IOUT = 270mA,VCC = 1.9V to 3.6V,
0.2
0.3
V
0.25
0.4
V
0.12
0.2
V
0.2
0.35
V
VOUT11
Ta = -20 to 85°C
(single connection)
VOUT = Upper Tr and Under Tr
IN1 = High level, IN2 to IN4 = Low level
Supplementation: Standard similar as for IN2
to IN4 = High level
VOUT12
IOUT = 350mA,VCC = 1.9V to 3.6V,
Ta = -20 to 85°C
VOUT = Upper Tr and Under Tr
IN1 = High level, IN2 to IN4 = Low level
Supplementation: Standard similar as for IN2
to IN4 = High level
Output saturation voltage2
VOUT21
IOUT = 270mA,VCC = 1.9V to 3.6V,
Ta = -20 to 85°C
(parallel connection)
VOUT = Upper Tr and Under Tr
OUT1-3,OUT2-4 short. IN1 and IN3 = High
level, IN2 and IN4 = Low level
Supplementation: Standard similar as for IN2
and IN4 = High level
VOUT22
IOUT = 500mA,VCC = 1.9V to 3.6V,
Ta = -20 to 85°C
VOUT = Upper Tr and Under Tr
OUT1-3,OUT2-4 short. IN1 and IN3 = High
level,IN2 and IN4 = Low level
Supplementation: Standard similar as for IN2
and IN4 = High level
Output electric current with the
IPA
VIN = 1.9 to 3.6V, Ta = -20 to 85°C *1
9
mA
70
μA
parasitic element
Input current
Themal shutdown operation
IIN
VIN = 1.9V
32
Ttsd
*2: Design guarantee
140
°C
∆T
*2: Design guarantee
20
°C
temperature
Temperature hysteresis width
Spark killer Diode
Reverse current
IS(leak)
Forword voltage
VSF
VCC-OUT = 8V, VIN = Low level
10
μA
ISF = 400mA, VIN = Low level
1.7
V
*1: Output electric current with the parasitic element_IPA: The current value that the off ch(-free) output is pulled at the time of one side ch drive by a parasitic
element
*2: Design guarantee value and does not measure
* VSF: The current order direction voltage true in a time
No.A2014-2/5
LB1973JA
Package Dimensions
unit : mm (typ)
3178B
Pd max -- Ta
1.0
0.5
6.4
9
4.4
16
Allowable power dissipation,Pd max - W
5.2
1
8
0.65
0.15
(0.33)
1.5max
0.22
Mounted on a specified board :
114.3mm x 76.1mm x 1.6mm
glass epoxy
0.8
0.6
0.4
0.2
0
-20
20
(1.3)
0
40
60
80 85
100
0.1
Ambient temperature, Ta -- C
SANYO : SSOP16(225mil)
9
8
NC
GND
10
7
IN2
11
6
IN1
NC
OUT2
OUT1
5
NC
12
4
IN3
13
NC
OUT3
14
3
IN4
OUT4
15
2
NC
16
1
VCC
NC
Pin Assignment
(Top View)
Truth Table
Input
IN1
Output
IN2
IN3
IN4
Low
Low
Low
Low
High
Low
Low
High
-
-
High
-
-
-
High
Low
Low
High
High
-
-
-
High
High
OUT1
OUT2
OUT3
OUT4
Off
Off
-
-
Off
Off
High
Low
Low
High
-
-
Mode
Standby mode
Channel 1, forward
Channel 1, reverse
High
Low
Channel 2, forward
Low
High
Channel 2, reverse
The logic output for the first high-level input is produced.
No.A2014-3/5
LB1973JA
Stepping motor control example
(1) Timing chart for 2-phase drive
IN1
IN2
IN3
IN4
Channel 1
output mode
Standby
Channel 2
output mode
Standby
Forward
Reverse
Forward
Forward
Reverse
Reverse
Forward
Forward
Standby
Reverse Forward
Standby
(2) Timing chart for 1-2 phase drive
IN1
IN2
IN3
IN4
Channel 1
output mode
Standby
Channel 2
output mode
Standby
Forward
OFF
Reverse
OFF
Forward
OFF
Reverse
Forward
Standby
OFF Forward
Standby
No.A2014-4/5
LB1973JA
Block Diagram
VCC
30K
OUT2
IN2
100K
30K
IN3
100K
Control Block Circuit
30K
IN1
Thermal shutdown circuit
100K
OUT1
OUT3
OUT4
30K
IN4
100K
GND
ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at
www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no
warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the
application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical
experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use
as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in
which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for
any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or
death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the
part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PS No.A2014-5/5
Similar pages