Delta IPM Output short circuit protection Datasheet

FEATURES

High efficiency: 93% @ 12Vin, 5V/8A out

Small size and low profile:
17.8x15.0x7.8mm (0.70”x0.59”x0.31”)

Output voltage adjustment: 0.8V~5V

Monotonic startup into normal and
pre-biased loads

Input UVLO, output OCP

Remote ON/OFF

Output short circuit protection

Fixed frequency operation

Mositure Sensitivity Level (MSL) 3

Copper pad to provide excellent thermal
performance

ISO 9001, TL 9000, ISO 14001, QS9000,
OHSAS18001 certified manufacturing

UL/cUL 60950 (US & Canada) Recognized,
and TUV (EN60950) Certified

CE mark meets 73/23/EEC and 93/68/EEC
directives
Delphi Series IPM, Non-Isolated, Integrated
Point-of-Load Power Modules: 8V~14V input,
0.8~5V and 8A Output Current
OPTIONS

The
Delphi
Series
IPM12S
non-isolated,
fully
SMD or SIP package
integrated
Point-of-Load (POL) power modules, are the latest offerings from a
world leader in power systems technology and manufacturing -Delta Electronics, Inc. This product family provides up to 8A of
output current or 40W of output power in an industry standard,
compact, IC-like, molded package. It is highly integrated and does
not require external components to provide the point-of-load
function. A copper pad on the back of the module; in close contact
with the internal heat dissipation components; provides excellent
thermal performance. The assembly process of the modules is fully
automated with no manual assembly involved. These converters
possess outstanding electrical and thermal performance, as well as
extremely high reliability under highly stressful operating conditions.
IPM12S operates from an 8V~14V source and provides a
programmable output voltage of 0.8V to 5V. The IPM product family
is available in both a SMD or SIP package. IPM family is also
available for input 3V~5.5V, please refer to IPM04S datasheet for
details.
DATASHEET
IPM12S0A0R/S08_03202007
APPLICATIONS

Telecom/DataCom

Wireless Networks

Optical Network Equipment

Server and Data Storage

Industrial/Test Equipment
TECHNICAL SPECIFICATIONS
TA = 25°C, airflow rate = 300 LFM, Vin = 12Vdc, nominal Vout unless otherwise noted.
PARAMETER
NOTES and CONDITIONS
IPM12S0A0R/S08FA
Min.
ABSOLUTE MAXIMUM RATINGS
Input Voltage (Continuous)
Operating Temperature
Storage Temperature
INPUT CHARACTERISTICS
Operating Input Voltage
Input Under-Voltage Lockout
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Maximum Input Current
No-Load Input Current
Off Converter Input Current
Input Reflected-Ripple Current
Input Voltage Ripple Rejection
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Adjustable Range
Output Voltage Regulation
Over Line
Over Load
Over Temperature
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
RMS
Output Current Range
Output Voltage Over-shoot at Start-up
Output DC Current-Limit Inception
DYNAMIC CHARACTERISTICS
Dynamic Load Response
Positive Step Change in Output Current
Negative Step Change in Output Current
Setting Time to 10% of Peak Devitation
Turn-On Transient
Start-Up Time, From On/Off Control
Start-Up Time, From Input
Output Voltage Rise Time
Maximum Output Startup Capacitive Load
EFFICIENCY
Vo=0.9V
Vo=1.2V
Vo=1.5V
Vo=1.8V
Vo=2.5V
Vo=3.3V
Vo=5.0V
FEATURE CHARACTERISTICS
Switching Frequency
ON/OFF Control, (Logic High-Module ON)
Logic High
Logic Low
ON/OFF Current
Leakage Current
GENERAL SPECIFICATIONS
MTBF
Weight
Refer to figure 34 for measuring point
Typ.
0
-40
-55
8
12
Max.
Units
15
+113
+125
Vdc
°C
°C
14
7.9
7.6
Vin=Vin,min to Vin,max, Io=Io,max
3
20
TBD
P-P 1µH inductor, 5Hz to 20MHz
120 Hz
Vin=12V, Io=Io,max, Ta=25℃
Vin=Vin,min to Vin,max
Io=Io,min to Io,max
Ta=Ta,min to Ta,max
Over sample load, line and temperature
5Hz to 20MHz bandwidth
Full Load, 1µF ceramic, 10µF tantalum
Full Load, 1µF ceramic, 10µF tantalum
Vo≦3.6Vdc
Vo>3.6Vdc
Vin=10V to 14V, Io=0A to 16A, Ta=25℃
0.889
0.8
0.900
0.1
0.3
0.01
-3.0
40
15
V
V
A
mA
mA
mAp-p
dB
0.911
5
Vdc
V
0.025
+3.0
% Vo,set
% Vo,set
%Vo,set/℃
% Vo,set
60
30
8
6
1
mVp-p
mV
A
A
% Vo,set
% Io
100
100
40
150
150
mVpk
mVpk
µs
25
25
15
1500
5000
ms
ms
ms
µF
µF
0
0
0
200
10µF Tan & 1µF Ceramic load cap, 2.5A/µs
50% Io, max to 100% Io, max
100% Io, max to 50% Io, max
4.5
85
10
40
V
Io=Io.max
Time for Vo to rise from 10% to 90% of Vo,set,
Full load; ESR ≧1mΩ
Full load; ESR ≧10mΩ
5
17
17
9
Vin=12V, Io=Io,max, Ta=25℃
Vin=12V, Io=Io,max, Ta=25℃
Vin=12V, Io=Io,max, Ta=25℃
Vin=12V, Io=Io,max, Ta=25℃
Vin=12V, Io=Io,max, Ta=25℃
Vin=12V, Io=Io,max, Ta=25℃
Vin=12V, Io=Io,max, Ta=25℃
73
78
80
83
86
88
91
75.0
80.5
83.0
85.0
88.5
91.0
93.0
%
%
%
%
%
%
%
485
kHz
Module On
Module Off
Ion/off at Von/off=0
Logic High, Von/off=5V
Io=80% Io,max, Ta=25℃
2.4
-0.2
0.25
20
6
Vin,max
0.8
1
50
V
V
mA
µA
M hours
grams
DS_IPM12S0A008_03202007
2
ELECTRICAL CHARACTERISTICS CURVES
90
80
EFFICIENCY(%)
EFFICIENCY(%)
90
70
Vi=14V
Vi=12V
Vi=10V
Vi=8V
60
80
Vi=14V
Vi=12V
Vi=10V
Vi=8V
70
60
50
1
2
3
4
5
6
7
8
1
9
2
3
4
6
7
8
9
LOAD (A)
LOAD (A)
Figure 1: Converter efficiency vs. output current
(0.90V output voltage)
Figure 2: Converter efficiency vs. output current
(1.2V output voltage)
90
EFFICIENCY(%)
90
EFFICIENCY(%)
5
Vi=14V
Vi=12V
Vi=10V
Vi=8V
80
70
Vi=14V
Vi=12V
Vi=10V
Vi=8V
80
70
1
2
3
4
5
6
7
8
9
1
2
3
4
LOAD (A)
5
6
7
8
9
LOAD (A)
Figure 3: Converter efficiency vs. output current
(1.5V output voltage)
Figure 4: Converter efficiency vs. output current
(1.8V output voltage)
100
EFFICIENCY(%)
EFFICIENCY(%)
90
Vi=14V
Vi=12V
Vi=10V
Vi=8V
80
70
90
Vi=14V
Vi=12V
Vi=10V
Vi=8V
80
70
1
2
3
4
5
6
7
8
LOAD (A)
Figure 5: Converter efficiency vs. output current
(2.0V 0utput voltage)
9
1
2
3
4
5
6
7
8
9
LOAD (A)
Figure 6: Converter efficiency vs. output current
(2.5V output voltage)
DS_IPM12S0A008_03202007
3
ELECTRICAL CHARACTERISTICS CURVES
100
EFFICIENCY(%)
EFFICIENCY(%)
100
90
Vi=14V
Vi=12V
Vi=10V
Vi=8V
80
90
Vi=14V
Vi=12V
Vi=10V
Vi=8V
80
70
70
1
2
3
4
5
6
7
8
9
LOAD (A)
1
2
3
4
5
6
7
8
9
LOAD (A)
Figure 7: Converter efficiency vs. output current
(3.3V output voltage)
Figure 8: Converter efficiency vs. output current
(5.0V output voltage)
Figure 9: Output ripple & noise at 12Vin, 0.9V/8A out
Figure 10: Output ripple & noise at 12Vin, 2.5V/8A out
Figure 11: Output ripple & noise at 12Vin, 3.3V/8A out
Figure 12: Output ripple & noise at 12Vin, 5.0V/6A out
DS_IPM12S0A008_03202007
4
ELECTRICAL CHARACTERISTICS CURVES
Figure 13: Power on waveform at 12vin, 2.5V/8A out with
application of Vin
Figure 14: Power on waveform at 12vin, 5.0V/6A out with
application of Vin
Figure 15: Power off waveform at 12vin, 2.5V/8A out with
application of Vin
Figure 16: Power off waveform 12vin, 5.0V/8A out with
application of Vin
Figure 17: Remote turn on delay time at 12vin, 2.5V/8A out
Figure 18: Remote turn on delay time at 12vin, 5.0V/6A out
DS_IPM12S0A008_03202007
5
ELECTRICAL CHARACTERISTICS CURVES
Figure 19: Turn on delay at 12vin, 2.5V/8A out with
application of Vin
Figure 21: Typical transient response to step load change at
2.5A/μS from 100% to 50% of Io, max at 12Vin,
5.0V out (measurement with a 1uF ceramic
and a 10μF tantalum
Figure 20: Turn on delay at 12vin, 5.0V/6A out with
application of Vin
Figure 22: Typical transient response to step load change at
2.5A/μS from 50% to 100% of Io, max at 12Vin,
5.0V out (measurement with a 1uF ceramic
and a 10μF tantalu)
DS_IPM12S0A008_03202007
6
TEST CONFIGURATIONS
DESIGN CONSIDERATIONS
Input Source Impedance
L
VI(+)
2 47uF
Tantalum
BATTERY
VI(-)
Note: Input reflected-ripple current is measured with a
simulated source inductance. Current is
measured at the input of the module.
Figure 23: Input reflected-ripple current test setup
To maintain low-noise and ripple at the input voltage, it is
critical to use low ESR capacitors at the input to the
module. Figure 26 shows the input ripple voltage
(mVp-p) for various output models using 2x47 uF low
ESR tantalum capacitors (SANYO P/N:16TPB470M,
47uF/16V or equivalent) or 2x22 uF very low ESR
ceramic capacitors (TDK P/N:C3225X7S1C226MT,
22uF/16V or equivalent).
The input capacitance should be able to handle an AC
ripple current of at least:
Irms  Iout
Vout 
Vout 
1 

Vin 
Vin 
Arms
400
1uF
10uF
tantalum ceramic
SCOPE
Resistive
Load
GND
Note: Use a 10μF tantalum and 1μF capacitor. Scope
measurement should be made using a BNC
connector.
Input Ripple Voltage (mVp-p)
Vo
350
300
250
200
150
100
Tantalum
Ceramic
50
0
Figure 24: Peak-peak output noise and startup transient
measurement test setup
0
1
2
3
4
5
6
Output Voltage (Vdc)
VI
Vo
GND
Figure 25: Output voltage and efficiency measurement test
setup
Note: All measurements are taken at the module
terminals. When the module is not soldered (via
socket), place Kelvin connections at module
terminals to avoid measurement errors due to
contact resistance.
(
Figure 26: Input ripple voltage for various output models,
Io = 8A (Cin = 2x47uF tantalum capacitors or
2x22uF ceramic capacitors at the input)
The power module should be connected to a low
ac-impedance input source. Highly inductive source
impedances can affect the stability of the module. An
input capacitance must be placed close to the modules
input pins to filter ripple current and ensure module
stability in the presence of inductive traces that supply
the input voltage to the module.
Vo  Io
)  100 %
Vi  Ii
DS_IPM12S0A008_03202007
7
DESIGN CONSIDERATIONS
FEATURES DESCRIPTIONS
Safety Considerations
Over-Current Protection
For safety-agency approval the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standards.
To provide protection in an output over load fault
condition, the unit is equipped with internal over-current
protection. When the over-current protection is
triggered, the unit enters hiccup mode. The units
operate normally once the fault condition is removed.
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the
input must meet SELV requirements. The power module
has extra-low voltage (ELV) outputs when all inputs are
ELV.
The input to these units is to be provided with a
maximum 10A time-delay fuse in the ungrounded lead.
Remote On/Off
The IPM series power modules have an On/Off control
pin for output voltage remote On/Off operation. The
On/Off pin is an open collector/drain logic input signal
that is referenced to ground. When On/Off control pin is
not used, leave the pin unconnected.
Pre-Bias Startup Capability
The IPM would perform the monotonic startup into the
pre-bias loads; so as to avoid a system voltage drop
occur upon application. In complex digital systems an
external voltage can sometimes be presented at the
output of the module during power on. This voltage may
be feedback through a multi-supply logic component,
such as FPGA or ASIC. Another way might be via a clamp
diode as part of a power up sequencing implementation.
The remote on/off pin is internally connected to +Vin
through an internal pull-up resistor. Figure 27 shows the
circuit configuration for applying the remote on/off pin.
The module will execute a soft start ON when the
transistor Q1 is in the off state.
The typical rise for this remote on/off pin at the output
voltage of 2.5V and 5.0V are shown in Figure 17 and 18.
Vo
Vin
IPM
On/Off
RL
Q1
GND
Figure 27: Remote on/off implementation
DS_IPM12S0A008_03202007
8
FEATURES DESCRIPTIONS (CON.)
Output Voltage Programming
The output voltage of IPM can be programmed to any
voltage between 0.8Vdc and 5Vdc by connecting one
resistor (shown as Rtrim in Figure 28, 29) between the
TRIM and GND pins of the module to trim up (0.9V ~ 5V)
and between the Trim and +Output to trim down (0.8V ~
0.9V). Without this external resistor, the output voltage of
the module is 0.9 Vdc. To calculate the value of the
resistor Rtrim for a particular output voltage Vo, please
use the following equation:
For example, to program the output voltage of a IPM
module to 3.3 Vdc, Vtrim is calculated as follows
Vtrim = 0.7439 – 0.0488 x 3.3
Vtrim = 0.5829V
Trim up
Rtrim =
3.746
Vout –0.9
- 0.261 (KΩ )
1.070
0.9 - Vout
- 5.612 (KΩ )
Trim Down
Rtrim =
Figure 28:
Trim up Circuit configuration for programming
output voltage using an external resistor
Rtrim is the external resistor in KΩ
Vout is the desired output voltage
For example: to program the output voltage of the IPM
module to 3.3Vdc, Rtrim is calculated as follows:
Vout
Rtrim
Load
Rtrim =
3.746
3.3 –0.9
Trim
- 0.261 (KΩ )
GND
Rtrim = 1.300 KΩ
Figure 29:
Trim down Circuit configuration for programming
output voltage using an external resistor
IPM can also be programmed by applying a voltage
between the TRIM and GND pins (Figure 30). The
following equation can be used to determine the value of
Vtrim needed for a desired output voltage Vo:
Vtrim = 0.7439 – 0.0488Vo
Vtrim is the external voltage in V
Vo is the desired output voltage
Figure 30: Circuit configuration for programming output voltage
using external voltage source
DS_IPM12S0A008_03202007
9
FEATURE DESCRIPTIONS (CON.)
Table 1 provides Rtrim values required for some common
output voltages, while Table 2 provides value of external
voltage source, Vtrim, for the same common output
voltages. By using a 0.5% tolerance resistor, set point
tolerance of ±2% can be achieved as specified in the
electrical specification.
Table 1
VO (V)
0.800
0.900
1.0
1.2
1.5
1.8
2.5
3.3
5.0
Rtrim (Ω)
5.09K
Open
37.2K
12.2K
5.98K
3.90K
2.08K
1.30K
653
The amount of power delivered by the module is the
voltage at the output terminals multiplied by the output
current. When using the trim feature, the output voltage
of the module can be increased, which at the same
output current would increase the power output of the
module. Care should be taken to ensure that the
maximum output power of the module must not exceed
the maximum rated power (Vo.set x Io.max ≤ P max).
Voltage Margining
Output voltage margining can be implemented in the IPM
modules by connecting a resistor, R margin-up, from the Trim
pin to the ground pin for margining-up the output voltage
and by connecting a resistor, Rmargin-down, from the Trim pin
to the output pin for margining-down. Figure 31 shows
the circuit configuration for output voltage margining. If
unused, leave the trim pin unconnected.
Table 2
VO (V)
0.80
0.90
1.2
1.5
1.8
2.5
3.3
5.0
Vtrim (V)
0.705
0.700
0.685
0.671
0.656
0.622
0.583
0.500
Vo
Vin
IPM
Rmargin-down
Q1
On/Off
Trim
Rmargin-up
Rtrim
Q2
GND
Figure 31: Circuit configuration for output voltage margining
DS_IPM12S0A008_03202007
10
THERMAL CONSIDERATIONS
THERMAL CURVES
Thermal management is an important part of the system
design. To ensure proper, reliable operation, sufficient
cooling of the power module is needed over the entire
temperature range of the module. Convection cooling is
usually the dominant mode of heat transfer.
Hence, the choice of equipment to characterize the
thermal performance of the power module is a wind
tunnel.
Thermal Testing Setup
Delta’s DC/DC power modules are characterized in
heated vertical wind tunnels that simulate the thermal
environments encountered in most electronics
equipment. This type of equipment commonly uses
vertically mounted circuit cards in cabinet racks in which
the power modules are mounted.
The following figure shows the wind tunnel
characterization setup. The power module is mounted
on a test PWB and is vertically positioned within the
wind tunnel. The height of this fan duct is constantly kept
at 25.4mm (1’’).
Figure 33: Temperature measurement location
* The allowed maximum hot spot temperature is defined at 113℃.
Output Current(A)
9
IPM12S(Standard) Output Current vs. Ambient Temperature and Air Velocity
@ Vin = 12V, Vo = 5V (Either Orientation)
8
7
Natural
Convection
6
100LFM
Thermal Derating
5
200LFM
4
Heat can be removed by increasing airflow over the
module. To enhance system reliability, the power
module should always be operated below the maximum
operating temperature. If the temperature exceeds the
maximum module temperature, reliability of the unit may
be affected.
300LFM
3
400LFM
2
500LFM
1
600LFM
0
35
PWB
FACING PWB
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (℃)
Figure 34: Output current vs. ambient temperature and air velocity
@ Vin=12V, Vo=5V
MODULE
9
Output Current(A)
IPM12S(Standard) Output Current vs. Ambient Temperature and Air Velocity
@ Vin = 12V, Vo = 3.3V (Either Orientation)
8
Natural
Convection
7
AIR VELOCITY
AND AMBIENT
TEMPERATURE
MEASURED BELOW
THE MODULE
6
100LFM
50.8 (2.0”)
5
200LFM
4
AIR FLOW
300LFM
3
400LFM
2
12.7 (0.5”)
25.4 (1.0”)
500LFM
1
0
Figure 32: Wind tunnel test setup figure
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (℃)
Figure 35: Output current vs. ambient temperature and air velocity
@ Vin=12V, Vo=3.3V
DS_IPM12S0A008_03202007
11
THERMAL CURVES (CON.)
Output Current(A)
9
IPM12S(Standard) Output Current vs. Ambient Temperature and Air Velocity
@ Vin = 12V, Vo = 2.5V (Either Orientation)
Output Current(A)
9
IPM12S(Standard) Output Current vs. Ambient Temperature and Air Velocity
@ Vin = 12V, Vo = 1.2V (Either Orientation)
8
8
Natural
Convection
7
Natural
Convection
7
6
6
100LFM
5
100LFM
5
4
4
200LFM
200LFM
3
3
300LFM
2
2
300LFM
1
1
400LFM
0
0
35
40
45
50
55
60
65
70
75
Figure 36: Output current vs. ambient temperature and air velocity
@ Vin=12V, Vo=2.5V
9
35
80
85
Ambient Temperature (℃)
9
50
55
60
65
70
75
80
85
Ambient Temperature (℃)
IPM12S(Standard) Output Current vs. Ambient Temperature and Air Velocity
@ Vin = 12V, Vo = 1.0V (Either Orientation)
Output Current(A)
8
8
Natural
Convection
7
Natural
Convection
7
6
6
100LFM
100LFM
5
5
4
4
200LFM
200LFM
3
3
2
2
300LFM
1
300LFM
1
0
0
35
40
45
50
55
60
65
70
75
Output Current(A)
35
80
85
Ambient Temperature (℃)
Figure 37: Output current vs. ambient temperature and air velocity
@ Vin=12V, Vo=1.8V
9
45
Figure 39: Output current vs. ambient temperature and air velocity
@ Vin=12V, Vo=1.2V
IPM12S(Standard) Output Current vs. Ambient Temperature and Air Velocity
@ Vin = 12V, Vo = 1.8V (Either Orientation)
Output Current(A)
40
IPM12S(Standard) Output Current vs. Ambient Temperature and Air Velocity
@ Vin = 12V, Vo = 1.5V (Either Orientation)
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (℃)
Figure 40: Output current vs. ambient temperature and air velocity
@ Vin=12V, Vo=1.0V
9
Output Current(A)
IPM12S(Standard) Output Current vs. Ambient Temperature and Air Velocity
@ Vin = 12V, Vo = 0.9V (Either Orientation)
8
8
Natural
Convection
7
Natural
Convection
7
6
6
100LFM
5
100LFM
5
4
4
200LFM
3
200LFM
3
2
2
300LFM
300LFM
1
1
0
0
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (℃)
Figure 38: Output current vs. ambient temperature and air velocity
@ Vin=12V, Vo=1.5V
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (℃)
Figure 41: Output current vs. ambient temperature and air velocity
@ Vin=12V, Vo=0.9V
DS_IPM12S0A008_03202007
12
PICK AND PLACE LOCATION
SURFACE- MOUNT TAPE & REEL
All dimensions are in millimeters (inches)
All dimensions are in millimeters (inches)
LEAD FREE PROCESS RECOMMEND TEMP. PROFILE
Temp.
20 ~ 40sec.
Peak Temp. 240 ~ 245 0 C
217 0 C
Ramp down
max. 6.0 0 C/sec
200 0 C
150 0 C
Preheat time
60 ~ 180 sec.
Time 60 ~ 150 sec.
Above 217 0 C
Ramp up
max. 3.0 0 C/sec
25 0 C
Time
Note: All temperature refers to topside of the package, measured on the package body surface.
DS_IPM12S0A008_03202007
13
MECHANICAL DRAWING
SMD PACKAGE
SIP PACKAGE
1 2 3 4 5
RECOMMEND PWB PAD LAYOUT
RECOMMEND PWB HOLE LAYOUT
Note: The copper pad is recommended to connect to the ground.
7
6
1 2 3 4 5
1 2 3 4 5
Note: All dimension are in millimeters (inches) standard dimension tolerance is± 0.10(0.004”)
DS_IPM12S0A008_03202007
14
PART NUMBERING SYSTEM
IPM
12
S
0A0
R
08
Product
Family
Input Voltage
Number of
Outputs
Output Voltage
Package
Output
Current
0A0 - programmable
output
R - SIP
S - SMD
08 - 8A
10 - 10A
Integrated POL 04 - 3V ~ 5.5V
Module
12 - 8V ~ 14V
S - Single
F
A
Option Code
F- RoHS 6/6
A - Standard Function
(Lead Free)
MODEL LIST
Packaging
Input Voltage
Output Voltage
Output Current
Efficiency (Typical @
full load)
IPM12S0A0R08FA
SIP
8V ~ 14V
0.8V ~ 5V
8A
93%
IPM12S0A0S08FA
SMD
8V ~ 14V
0.8V ~ 5V
8A
93%
IPM04S0A0R10FA
SIP
3V ~ 5.5V
0.8V ~ 3.3V
10A
94%
IPM04S0A0S10FA
SMD
3V ~ 5.5V
0.8V ~ 3.3V
10A
94%
Model Name
CONTACT: www.deltaww.com/dcdc
USA:
Telephone:
East Coast: 978-656-3993
West Coast: 510-668-5100
Fax: (978) 656 3964
Email: [email protected]
Europe:
Telephone: +31-20-655-0967
Fax: +31-20-655-0999
Email: [email protected]
Asia & the rest of world:
Telephone: +886 3 4526107 x6220~6224
Fax: +886 3 4513485
Email: [email protected]
WARRANTY
Delta offers a two (2) year limited warranty. Complete warranty information is listed on our web site or is available upon
request from Delta.
Information furnished by Delta is believed to be accurate and reliable. However, no responsibility is assumed by Delta
for its use, nor for any infringements of patents or other rights of third parties, which may result from its use. No license
is granted by implication or otherwise under any patent or patent rights of Delta. Delta reserves the right to revise these
specifications at any time, without notice.
DS_IPM12S0A008_03202007
15
Similar pages