3M™ CF Card Header CompactFlash™ Type II, Surface Mount 7E50 Series • Headers mate with both CompactFlash™ Type I and Type II cards • Polarization options for top or bottom boardmount • Extended guide rails enable accurate and easy card insertion • Single row surface mount solder tails facilitate auto placement and IR soldering • Optional 2 mm board standoff enables board population • Meets CFA standards for known compatibility and reliability • See regulatory information appendix (RIA) for chemical compliance information Date Modified: November 5, 2007 TS-2082-C Sheet 1 of 3 Physical Insulation Material: High Temperature Thermoplastic Flammability: UL 94V-0 Color: Beige Contact Material: Copper Alloy Plating Underplating: 2.03 μm [ 80 μ″] Nickel Wiping Area: 0.38 μm [ 15 μ″ ] or 0.76 μm [ 30 μ″ ] Gold Solder Tails: 3.81μm [150μ″] Matte Tin or Gold Flash Marking 3M Logo Electrical Current Rating: 0.5 A Insulation Resistance: 103 MΩ at 500 VDC Withstanding Voltage: 500 VAC for 1 minute Environmental Temperature Rating: -40°C to +85°C Process Rating: Maximum 260 C (per J-STD-020C) Moisture Sensitivity Level: 1 (per J-STD-020C) CompactFlash is a registered trademark of Sandisk Corporation. 3 Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ CF Card Header CompactFlash™ Type II, Surface Mount 7E50 Series Pin Function L, Pin length Dim Pin Position Detect 3.50 [ .138 ] 25, 26 General Use 4.25 [ .167 ] All other pins Power 5.00 [ .197 ] 1, 13, 38, 50 0.635 .0250 6.13 .241 0.3175 .0125 6.13 .241 0.3175 .0125 r 0.01 [.004] 2X O 2.20 .087 2X 3.00 .118 2X 3.30 .130 0.60 .024 3.00 .118 18.00 .709 2X 18.50 .728 3M 2X 38.74 ±.05 1.525 ±.002 -D31.12 1.225 0.23 50X .009 ±.05 ±.002 l 0.20 [.008] A B-C D 0.40 ±.02 .016 ±.001 l 0.20 [.008] A B-C D 50X L 10.00 .394 26.00 1.024 LOGO 8.70 .343 44.70 1.760 PIN W PIN Y E 43.00 1.693 41.70 1.642 F PIN X PIN Z 15.24 .600 1.27 .050 1.27 .050 -A- mm [Inch] H G 2X O 0.60 .024 -C- Ordering Information 2X 46.00 1.811 .0 ± .3 mm .00 .000 ± .15 [ ] Dimensions for Reference only N7E50 - X516XX - XX - WF Plating Options: EA = 0.38 μm [ 15 μ″ ] Gold with Gold Flash tail EB = 0.76 μm [ 30 μ″ ] Gold with Gold Flash tail RA = 0.38 μm [15μ"] Gold with matte tin tail (RIA E1 & C1 apply) RB = 0.76μm [30μ"] Gold with matte tin tail (RIA E1 & C1 apply) Interconnect Solutions http://www.3M.com/interconnects/ -B- Tolerance Unless Noted 47.00 1.850 Q = CF I & II, 18.70 mm, Normal Type, Ejector not acceptable R = CF I & II, 18.70 mm, Inverse Type, Ejector not acceptable 3 1.60 .063 (RIA E1 & C1 apply) Packaging Options: Blank = Trays WF = Tape and Reel Board Standoff: 40 = None (Normal Type Only) 50 = 2.00 mm [ .079″ ] TS-2082-C Sheet 2 of 3 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ CF Card Header CompactFlash™ Type II, Surface Mount Part Number 7E50 Series E mm [ inch ] F mm [ inch ] G mm [ inch ] H mm [ inch ] N7E50-Q516XX-40 0.00 [ .000 ] 4.65 [ .183 ] 1.40 [ .055 ] 0.80 [ .031 ] N7E50-Q516XX-50 2.00 [ .079 ] 6.65 [ .262 ] 1.40 [ .055 ] N7E50-R516XX-50 2.00 [ .079 ] 6.65 [ .262 ] 0.80 [ .031 ] Pin X Pin Y Pin Z Pin 1 Pin 25 Pin 26 Pin 50 0.80 [ .031 ] Pin 1 Pin 25 Pin 26 Pin 50 1.40 [ .055 ] Pin 50 Pin 26 Pin 25 Pin 1 Pin W 38.74 ±.05 1.525 ±.002 PIN Y 2X O 30 ±.05 2.20 91 ±.002 .087 PIN Z 0.635 .0250 2X 7.50 .295 1.75 ±.03 .069 ±.001 -A- 2X O 2X 2X PIN X 31.12 1.225 PIN W 3.00 .118 18.50 ±.05 .728 ±.002 2X 4.50 .177 50X 0.40 ±.05 .016 ±.002 l 0.08 [.003] A-B A 3.50 .138 2X -B- 44.50 ±.05 1.752 ±.002 2X O 3.00 ±.05 .118 ±.002 2X 18.00 ±.10 .709 ±.004 0.90 ±.03 .035 ±.001 46.00 ±.05 1.811 ±.002 PCB LAYOUT Compact Flash Card Type 1 and 2 43.70 1.720 CARD INSERTION TS-2082-C Sheet 3 of 3 3 Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 Regulatory Information Appendix 3M Electronic Solutions Division/Interconnect EUROPE Appendix E1: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product is RoHS Compliant 2005/95/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E2: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/747/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E3: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as amended by Commission Decision 2005/618/EC. This product contains lead in the solder tail area in excess of the maximum concentration value allowed. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E4: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/717/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.product Warranty stated below. RIA-2217A-c Appendix E5: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under Item 6 of the Annex to the Directive. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. CHINA Appendix C1: China RoHS Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix C2: China RoHS Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the product Warranty stated below. RIA-2217A-c Appendix C3: China RoHS Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the product Warranty stated below. Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of 90 days from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 3M Electronics Interconnect Products 6801 River Place Blvd. Austin, TX 78726-9000 U.S.A. 1-800-225-5373 www.3m.com/interconnects Please recycle. Printed in USA. © 3M 2007. All rights reserved. RIA-2217A-c 3M is a trademark of 3M Company.