TI LM8801TME-1.82/NOPB High precision 6mhz, 600 ma synchronous step-down dc-dc converter for mobile application Datasheet

LM8801
www.ti.com
SNVS597H – APRIL 2009 – REVISED MAY 2013
LM8801 High Precision 6MHz, 600 mA Synchronous Step-Down DC-DC Converter for
Mobile Applications
Check for Samples: LM8801
FEATURES
APPLICATIONS
•
•
•
•
•
•
•
•
•
•
•
•
1
2
•
•
•
•
•
•
•
•
Over 90% Efficiency at 6 MHz Operation
600 mA Maximum Load Capability
6 MHz PWM Fixed Switching Frequency (typ.)
27 µA (typ.) Quiescent Current in PFM Mode
Wide Input Voltage Range: 2.3V to 5.5V
VOUT = 1.0V to 2.9V with 50 mV steps
±1.5% DC Output Voltage Precision Over
Temperature
Best-in-Class Load Transient Response
Low Output Ripple in PFM Mode
Automatic PFM/PWM Mode Switching
Current Overload and Thermal Shutdown
Protection
Internal Soft-Start
6-bump DSBGA Package
– (1.065 x 1.265 , 0.6 mm or 0.25 mm height)
Total Solution Size < 7mm2 (works with 0402
capacitors)
UVLO
Mobile Phones
MP3 players
Wireless LAN
PDAs, Pocket PCs
Portable Hard Disk Drives
DESCRIPTION
The LM8801 step-down DC-DC converter is
optimized for powering ultra-low voltage circuits from
a single Li-Ion cell and input voltage rails from 2.3V to
5.5V. It provides up to 600 mA load current over the
entire input voltage range.
The LM8801 has a mode-control pin that allows the
user to select continuous PWM operation over the
complete load range or an auto PFM-PWM mode that
changes modes automatically depending on the load.
During PWM mode, the device operates at a fixedfrequency of 6 MHz (typ.). In Auto PFM-PWM mode,
hysteretic PFM extends the battery life through
reduction of the quiescent current during light loads
and system standby.
The LM8801 is available in a 6-bump DSBGA
package. Only three compact external surface-mount
components, an inductor and two capacitors, are
required.
Efficiency vs. Output Current
(Auto Mode, VOUT = 1.82V)
Typical Application Circuit
100
90
2.3V
2.7V
EFFICIENCY (%)
80
4.2V
70
3.6V
60
50
40
30
20
COUT = 4.7 µF, TDK
L = 0.5 µH, FDK
10
0
0.1
1
10
100
1000
OUTPUT CURRENT (mA)
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009–2013, Texas Instruments Incorporated
LM8801
SNVS597H – APRIL 2009 – REVISED MAY 2013
www.ti.com
Connection Diagram
6-Bump DSBGA Package
See package numbers YFQ0006LCA and YQA0006LCA
Pin Descriptions
Pin Number
Name
A1
Mode
Description
A2
VIN
Power supply input. Connect to the input filter capacitor (Typical Application Circuit, page 1).
B1
SW
Switching node connection to the internal PFET switch and NFET synchronous rectifier.
B2
EN
Enable pin. The device is in shutdown mode when voltage to this pin is < 0.4V and enabled
when > 1.2V. Do not leave this pin floating.
C1
FB
Feedback analog input. Connect directly to the output filter capacitor (Typical Application
Circuit, page 1).
C2
GND
Auto mode and forced PWM mode selection. Forced PWM = HIGH; Auto = LOW.
Ground pin.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Dissipation Rating Table
θJA
85°CW
(1)
2
TA ≤ 25°C
Power Rating
(1)
1176 mW
TA = 60°C
Power Rating
TA = 85°C
Power Rating
765 mW
470 mW
Junction-to-ambient thermal resistance is highly application and board-layout dependent. In applications where high power dissipation
exists, special care must be given to thermal dissipation issues in board design.
Submit Documentation Feedback
Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM8801
LM8801
www.ti.com
SNVS597H – APRIL 2009 – REVISED MAY 2013
Absolute Maximum Ratings
(1) (2)
−0.2V to 6.0V
VIN Pin to GND
−0.2V to 6.0V
EN, MODE pin to GND
FB, SW pin
(VIN
Junction Temperature (TJ-MAX)
+150°C
−65°C to +150°C
Storage Temperature Range
Continuous Power Dissipation
(GND−0.2V) to
+ 0.2V) w/ 6.0V max
(3)
Internally Limited
Maximum Lead Temperature
(Soldering, 10 sec.)
ESD Rating
260°C
(4)
Human Body Model
2 kV
Machine Model
(1)
(2)
(3)
(4)
200V
Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under
which operation of the device is specified. Operating Ratings do not imply performance limits. For performance limits and associated test
conditions, see the Electrical Characteristics tables.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office / Distributors for
availability and specifications.
Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ = 150°C (typ.) and
disengages at TJ = 130°C (typ.).
The Human Body Model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. The machine model is a 200 pF
capacitor discharged directly into each pin. MIL-STD-883–3015.7.
Operating Ratings
(1) (2)
Input Voltage Range
2.3V to 5.5V
Recommended Load Current
0 mA to 600 mA
−30°C to +125°C
Junction Temperature (TJ) Range
Ambient Temperature (TA) Range
(1)
(2)
(3)
(3)
−30°C to +85°C
Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under
which operation of the device is specified. Operating Ratings do not imply performance limits. For performance limits and associated test
conditions, see the Electrical Characteristics tables.
All voltages are with respect to the potential at the GND pin.
In applications where high power dissipation and/or poor package resistance is present, the maximum ambient temperature may have to
be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP = 125°C),
the maximum power dissipation of the device in the application (PD-MAX) and the junction-to-ambient thermal resistance of the
part/package (θJA) in the application, as given by the following equation: TA-MAX = TJ-MAX− (θJAx PD-MAX). Due to the pulsed nature of
testing the part, the temp in the Electrical Characteristic table is specified as TA = TJ.
ThermaL Characteristics
Junction-to-Ambient Thermal Resistance (θJA) (DSBGA)
(1)
(1)
85°C/W
Junction-to-ambient thermal resistance is highly application and board-layout dependent. In applications where high power dissipation
exists, special care must be given to thermal dissipation issues in board design.
Submit Documentation Feedback
Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM8801
3
LM8801
SNVS597H – APRIL 2009 – REVISED MAY 2013
Electrical Characteristics
www.ti.com
(1) (2) (3)
Limits in standard typeface are for TA = 25°C. Limits in boldface type apply over the operating ambient temperature range
(−30°C ≤ TA = TJ ≤ +85°C). Unless otherwise noted, specifications apply to the LM8801 open loop Typical Application Circuit
with VOUT = 1.82V, VIN = EN = 3.6V.
Parameter
VFB
Feedback Voltage Tolerance
Line Reg. (closed loop)
Test Conditions
PWM
Min
Typ
-1.5
2.3V ≤ VIN ≤ 5.5V;
IOUT = 10 mA (PFM)
Max
Units
+1.5
%
0.2
%/V
2.3V ≤ VIN ≤ 5.5V;
IOUT = 200 mA (PWM)
0.048
Load Reg. (closed loop)
0.1 mA ≤ IOUT ≤ 600 mA;
VIN = 3.6V (Auto)
0.0019
ISHDN
Shutdown Supply Current
EN = 0V, SW = GND
0.08
1.0
µA
IQ_PFM
Quiescent Current in PFM Mode
No load, device is not switching
27
35
µA
IQ_PWM
Quiescent Current in PWM Mode
No load, device is not switching
0.57
0.7
RDSON (P)
Pin-Pin Resistance for PFET
VIN = VGS = 3.6V
220
RDSON (N)
Pin-Pin Resistance for Sync NFET
VIN = VGS = 3.6V
ILIM
PFET Peak Current Limit
900
VIH
Logic High Input, all control pins
1.2
VIL
Logic Low Input
IEN,MODE
Pin Input Current
FOSC
Internal Oscillator Frequency
UVLO
Under-Voltage Lock Out
VOUT
(1)
(2)
(3)
4
PWM Mode
%/mA
180
5.6
1100
mA
mΩ
mΩ
1300
mA
V
0.4
V
0.01
1
µA
6.0
6.4
MHz
2.0
V
All voltages are with respect to the potential at the GND pin.
Min and Max limits are specified by design, test or statistical analysis. Typical numbers represent the most likely norm.
The parameters in the electrical characteristic table are tested under open loop conditions at VIN = 3.6V unless otherwise specified. For
performance over the input voltage range and closed loop condition, refer to the datasheet curves.
Submit Documentation Feedback
Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM8801
LM8801
www.ti.com
SNVS597H – APRIL 2009 – REVISED MAY 2013
BLOCK DIAGRAM
EN
Reference Voltage
and Current Generator
VIN
MODE
Undervoltage
Lockout
+
-
Ref1
PFM PWM
Comparator
+
-
Ref2
+
PWM
Comparator
FB
+
Error
Amp
+
-
Control Logic
Driver
SW
-
Ramp
Generator
+
-
Oscillator
Output
Short
Protection
Thermal
Shutdown
+
-
Ref3
Ref4
GND
Simplified Functional Diagram
ORDERING INFORMATION (1) (2)
DSBGA package
Orderable
Voltage Option (V)
LM8801TME-1.2/NOPB
1.2
LM8801TMX-1.2/NOPB
LM8801TME-1.82/NOPB
LM8801TMX-1.82/NOPB
1.82
LM8801XUE-1.82/NOPB
LM8801XUX-1.82/NOPB
LM8801TME-2.9/NOPB
2.9
LM8801TMX-2.9/NOPB
(1)
(2)
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
Submit Documentation Feedback
Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM8801
5
LM8801
SNVS597H – APRIL 2009 – REVISED MAY 2013
www.ti.com
Typical Performance Characteristics
LM8801TM-1.82, Typical Application Circuit (page 1), VOUT = 1.82V, VIN = 3.6V, TA = 25°C, CIN = 2.2 µF, 0402
(JMK105BJ225MV-F), COUT = 4.7 µF, 0402, 6.3V (CL05A475MQ5NRNC), L = 0.5 µH, 2012 (MIPSZ2012D0R5), unless
otherwise noted.
Efficiency
vs.
Output Current (Auto Mode)
100
Efficiency
vs.
Output Current (PWM Mode)
100
2.3V
2.7V
2.3V
90
90
80
2.7V
EFFICIENCY (%)
EFFICIENCY (%)
80
4.2V
70
3.6V
60
50
70
60
50
40
30
3.6V
20
40
10
0
30
0.1
1
10
100
1000
4.2V
0.1
100
1000
Figure 1.
Figure 2.
Efficiency
vs.
Output Current (PWM Mode)
Efficiency
vs.
Output Current,
Auto Mode, VOUT = 1.2V
100
2.3V
VIN = 2.3V
VIN = 3.6V
90
90
2.7V
80
EFFICIENCY (%)
EFFICIENCY (%)
10
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
100
1
80
3.6V
70
60
70
60
VIN = 4.2V
50
4.2V
50
40
0
40
100
200
300
400
500
30
0.1
600
1
OUTPUT CURRENT (mA)
Output Voltage
vs.
Output Current (Auto Mode)
Output Voltage
vs.
Supply Voltage (PWM)
1.825
2.7V
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
1000
Figure 4.
1.840 PFM
1.835
1.830
3.6V
PWM
1.825 4.2V
1.823
I OUT = 600 mA
1.821
1.819
IOUT = 160 mA
1.817
1.820
I OUT = 300 mA
0
100
200
300
400
500
600
700
OUTPUT CURRENT (mA)
1.815
2.3
2.8
3.3
3.8
4.3
4.8
5.3
5.8
SUPPLY VOLTAGE (V)
Figure 5.
6
100
Figure 3.
1.845
1.815
10
OUTPUT CURRENT (mA)
Figure 6.
Submit Documentation Feedback
Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM8801
LM8801
www.ti.com
SNVS597H – APRIL 2009 – REVISED MAY 2013
Typical Performance Characteristics (continued)
LM8801TM-1.82, Typical Application Circuit (page 1), VOUT = 1.82V, VIN = 3.6V, TA = 25°C, CIN = 2.2 µF, 0402
(JMK105BJ225MV-F), COUT = 4.7 µF, 0402, 6.3V (CL05A475MQ5NRNC), L = 0.5 µH, 2012 (MIPSZ2012D0R5), unless
otherwise noted.
PFM ↔ PWM Mode Change Point
Typical Switching Waveform
(PWM Mode, IOUT = 300 mA)
160
140
PFM to PWM
LOAD (mA)
120
100
80
60
PWM to PFM
40
20
0
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VIN (V)
Figure 7.
Figure 8.
Typical Switching Waveform
(PFM Mode IOUT = 50 mA)
Load Transient Response
(0 ↔ 150 mA)
Figure 9.
Figure 10.
Load Transient Response
(50 ↔ 350 mA)
Load Transient Response
(150 ↔ 400 mA)
Figure 11.
Figure 12.
Submit Documentation Feedback
Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM8801
7
LM8801
SNVS597H – APRIL 2009 – REVISED MAY 2013
www.ti.com
Typical Performance Characteristics (continued)
LM8801TM-1.82, Typical Application Circuit (page 1), VOUT = 1.82V, VIN = 3.6V, TA = 25°C, CIN = 2.2 µF, 0402
(JMK105BJ225MV-F), COUT = 4.7 µF, 0402, 6.3V (CL05A475MQ5NRNC), L = 0.5 µH, 2012 (MIPSZ2012D0R5), unless
otherwise noted.
8
Load Transient Response
(250 ↔ 600 mA)
Load Transient Response
(VOUT = 1.2V, 0 ↔ 150 mA)
Figure 13.
Figure 14.
Load Transient Response
(VOUT = 1.2V, 50 ↔ 350 mA)
Load Transient Response
(VOUT = 1.2V, 150 ↔ 400 mA)
Figure 15.
Figure 16.
Load Transient Response
(VOUT = 1.2V, 250↔ 600 mA)
Line Transient Response
(3.0 VIN ↔ 3.6 VIN, 250 mA)
Figure 17.
Figure 18.
Submit Documentation Feedback
Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM8801
LM8801
www.ti.com
SNVS597H – APRIL 2009 – REVISED MAY 2013
Typical Performance Characteristics (continued)
LM8801TM-1.82, Typical Application Circuit (page 1), VOUT = 1.82V, VIN = 3.6V, TA = 25°C, CIN = 2.2 µF, 0402
(JMK105BJ225MV-F), COUT = 4.7 µF, 0402, 6.3V (CL05A475MQ5NRNC), L = 0.5 µH, 2012 (MIPSZ2012D0R5), unless
otherwise noted.
Startup in PFM Mode (IOUT = 20 mA)
Startup in PWM Mode (IOUT = 300 mA)
Figure 19.
Figure 20.
Startup in PWM Mode
(VOUT = 1.2V, IOUT = 300 mA)
Startup in PFM Mode
(VOUT = 1.2V, IOUT = 20 mA)
Figure 21.
Figure 22.
Submit Documentation Feedback
Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM8801
9
LM8801
SNVS597H – APRIL 2009 – REVISED MAY 2013
www.ti.com
OPERATION DESCRIPTION
DEVICE INFORMATION
The LM8801, a high-efficiency, step-down DC-DC switching buck converter, delivers a constant voltage from
either a single Li-Ion or three cell NiMH/NiCd battery to portable devices such as cell phones and PDAs. Using a
voltage mode architecture with synchronous rectification, the LM8801 has the ability to deliver up to 600 mA
depending on the input voltage and output voltage, ambient temperature, and the inductor chosen.
There are three modes of operation depending on the current required - PWM (Pulse Width Modulation), PFM
(Pulse Frequency Modulation), and shutdown. The device operates in PWM mode at load currents of
approximately 80 mA or higher, having voltage precision of ±1.5% with 90% efficiency or better. Lighter output
current loads cause the device to automatically switch into PFM for reduced current consumption (IQ = 27 µA
typ.) and a longer battery life. Shutdown mode turns off the device, offering the lowest current consumption
(ISHUTDOWN = 0.08 µA typ.).
Additional features include soft-start, under voltage protection, current overload protection, and thermal shutdown
protection. As shown in the Typical Application Circuit, only three external power components are required for
implementation.
CIRCUIT OPERATION
The LM8801 operates as follows. During the first portion of each switching cycle, the control block in the LM8801
turns on the internal PFET switch. This allows current to flow from the input through the inductor to the output
filter capacitor and load. The inductor limits the current to a ramp with a slope of (VIN − VOUT)/L, by storing energy
in a magnetic field. During the second portion of each cycle, the controller turns the PFET switch off, blocking
current flow from the input, and then turns the NFET synchronous rectifier on. The inductor draws current from
ground through the NFET to the output filter capacitor and load, which ramps the inductor current down with a
slope of –VOUT/L.
The output filter capacitor stores charge when the inductor current is high, and releases it when low, smoothing
the voltage across the load.
The output voltage is regulated by modulating the PFET switch on time to control the average current sent to the
load. The effect is identical to sending a duty-cycle modulated rectangular wave formed by the switch and
synchronous rectifier at the SW pin to a low-pass filter formed by the inductor and output filter capacitor. The
output voltage is equal to the average voltage at the SW pin.
PWM OPERATION
During PWM operation, the converter operates as a voltage-mode controller with input voltage feed forward. This
allows the converter to achieve excellent load and line regulation. The DC gain of the power stage is proportional
to the input voltage. To eliminate this dependence, feed forward inversely proportional to the input voltage is
introduced.
While in PWM mode, the output voltage is regulated by switching at a constant frequency and then modulating
the energy per cycle to control power to the load. At the beginning of each clock cycle the PFET switch is turned
on and the inductor current ramps up until the comparator trips and the control logic turns off the switch. The
current limit comparator can also turn off the switch in case the current limit of the PFET is exceeded. Then the
NFET switch is turned on and the inductor current ramps down. The next cycle is initiated by the clock turning off
the NFET and turning on the PFET.
AUTO MODE OPERATION
Setting Mode pin low places the LM8801 in Auto mode. By doing so the device will automatically switch between
PFM state and PWM (Pulse Width Modulation) state based on load demand. At light loads (less than 50 mA), the
device enters PFM mode and operates with reduced switching cycle and supply current to maintain high
efficiency. During PFM operation, the converter positions the output voltage slightly higher (+15 mV typ.) than the
nominal output voltage during PWM operation, allowing additional headroom for voltage drop during a load
transient from light to heavy load.
10
Submit Documentation Feedback
Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM8801
LM8801
www.ti.com
SNVS597H – APRIL 2009 – REVISED MAY 2013
PFM Mode at Light Load
High PFM Threshold
Load current increases
Target Output Voltage
ZA
xi
s
Low PFM Threshold
PWM Mode at Heavy Load
Zs
Axi
Figure 23. Operation in PFM Mode and Transfer to PWM Mode
INTERNAL SYNCHRONOUS RECTIFICATION
While in PWM mode, the LM8801 uses an internal NFET as a synchronous rectifier to reduce rectifier forward
voltage drop and associated power loss. Synchronous rectification provides a significant improvement in
efficiency whenever the output voltage is relatively low compared to the voltage drop across an ordinary rectifier
diode.
CURRENT LIMITING
A current limit feature allows the LM8801 to protect itself and external components during overload conditions.
PWM mode implements current limit using an internal comparator that trips at 1.1A (typ). If the output is shorted
to ground the device enters a timed current limit mode where the NFET is turned on for a longer duration until
the inductor current falls below a low threshold, ensuring inductor current has more time to decay, thereby
preventing runaway.
SHUTDOWN MODE
Setting the EN input pin low (<0.4V) places the LM8801 in shutdown mode. During shutdown the PFET switch,
NFET switch, reference, control and bias circuitry of the LM8801 are turned off. Setting EN high (>1.2V) enables
normal operation. While turning on the device with EN soft-start is activated. EN pin should be set low to turn off
the LM8801 during system power up and under-voltage conditions when the supply is less than 2.3V. Do not
leave the EN pin floating.
SOFT-START
The LM8801 has a soft-start circuit that limits in-rush current during start-up. During start-up the switch current
limit is increased in steps. Soft start is activated only if EN goes from logic low to logic high after VIN reaches
2.3V.
THERMAL SHUTDOWN PROTECTION
The LM8801 has a thermal overload protection function that operates to protect itself from short-term misuse and
overload conditions. When the junction temperature exceeds around 150°C, the device inhibits operation. Both
the PFET and the NFET are turned off. When the temperature drops below 130°C, normal operation resumes.
Prolonged operation in thermal overload conditions may damage the device and is considered bad practice.
Submit Documentation Feedback
Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM8801
11
LM8801
SNVS597H – APRIL 2009 – REVISED MAY 2013
www.ti.com
UVLO (UNDER-VOLTAGE LOCK OUT)
The LM8801 has an UVP comparator to turn the power device off in the case the input voltage or battery voltage
is too low. The typical UVP threshold is around 2V with 100 mV hysteresis.
APPLICATION INFORMATION
INDUCTOR SELECTION
There are two main considerations when choosing an inductor; the inductor should not saturate, and the inductor
current ripple is small enough to achieve the desired output voltage ripple. Different manufacturers follow
different saturation current rating specifications, so attention must be given to details. Saturation current ratings
are typically specified at 25°C so ratings at maximum ambient temperature of application should be requested
from manufacturer.
Minimum value of inductance to ensure good performance is 0.3 µH at (ILIM typ.) bias current over the
ambient temperature range.
Shielded inductors radiate less noise and should be preferred. There are two methods to choose the inductor
saturation current rating.
Method 1:
The saturation current should be greater than the sum of the maximum load current and the worst case average
to peak inductor current. This can be written as:
ISAT ! IOUTMAX + IRIPPLE
where IRIPPLE =
•
•
•
•
•
•
§VIN - VOUT· x §VOUT· x § 1 ·
© 2 x L ¹ © VIN ¹ © f ¹
(1)
IRIPPLE: average to peak inductor current
IOUTMAX: maximum load current (600 mA)
VIN: maximum input voltage in application
L: minimum inductor value including worst case tolerances (30% drop can be considered for method 1)
f: minimum switching frequency (5.4 MHz)
VOUT: output voltage
Method 2:
A more conservative and recommended approach is to choose an inductor that can handle the maximum current
limit of 1300 mA.
The inductor's resistance should be less than around 0.1Ω for good efficiency. Table 1 lists suggested inductors
and suppliers.
INPUT CAPACITOR SELECTION
A ceramic input capacitor of 2.2 µF, 6.3V is sufficient for most applications. Place the input capacitor as close as
possible to the VIN pin of the device. A larger value or higher voltage rating may be used to improve input voltage
filtering. Use X7R or X5R types; do not use Y5V. DC bias characteristics of ceramic capacitors must be
considered when selecting case sizes like 0402 and 0603.
The input filter capacitor supplies current to the top switch of the LM8801 in the first half of each cycle and
reduces voltage ripple imposed on the input power source. A ceramic capacitor's low ESR provides the best
noise filtering of the input voltage spikes due to this rapidly changing current. Select an input filter capacitor with
sufficient ripple current rating.
The input current ripple can be calculated as:
12
Submit Documentation Feedback
Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM8801
LM8801
www.ti.com
SNVS597H – APRIL 2009 – REVISED MAY 2013
IRMS = IOUTMAX x
r=
VOUT
x
VIN
§1¨
©
2
VOUT
VIN
+
r
12
·
¸
¹
(VIN - VOUT) x VOUT
L x f x IOUTMAX x VIN
(2)
The worst case is when VIN = 2 x VOUT.
Table 1. Suggested Inductors and Suppliers
Model
Vendor
Dimensions LxWxH (mm)
MIPSZ2012D0R5
FDK
2.0 x 1.2 x 1.0
LQM21PNR54MG0D
Murata
2.0 x 1.2 x 0.9
HSLI-201208AG-R47
Hitachi Metals
2.0 x 1.2 x 0.8
OUTPUT CAPACITOR SELECTION
Use a 4.7 μF, 6.3V ceramic capacitor, X7R or X5R types; do not use Y5V. DC bias characteristics of ceramic
capacitors must be considered when selecting case sizes 0402 and 0603. DC bias characteristics vary from
manufacturer to manufacturer, and DC bias curves should be requested from them as part of the capacitor
selection process. Minimum output capacitance to ensure good performance is 2.2 µF (for 4.7 µF
capacitor) at 1.8V DC bias including tolerances and over ambient temp range.
The output filter capacitor smooths out current flow from the inductor to the load, helps maintain a steady output
voltage during transient load changes and reduces output voltage ripple. These capacitors must be selected with
sufficient capacitance and sufficiently low ESR to perform these functions.
The output voltage ripple is caused by the charging and discharging of the output capacitor and also due to its
RESR and can be calculated as:
Voltage peak-to-peak ripple due to capacitance =
VPP-C =
IRIPPLE
4*f*C
(3)
Voltage peak-to-peak ripple due to ESR =
VPP-ESR = (2 * IRIPPLE) * RESR
Because these two components are out of phase, the rms value can be used to get an approximate value of
peak-to-peak ripple.
Voltage peak-to-peak ripple, root mean squared =
VPP-RMS =
VPP-C2 + VPP-ESR2
(4)
Note that the output voltage ripple is dependent on the current ripple and the equivalent series resistance of the
output capacitor (RESR). The RESR is frequency dependent (as well as temperature dependent); make sure the
value used for calculations is at the switching frequency of the part.
Table 2 lists suggested capacitors and suppliers.
Table 2. Suggested Capacitors and Suppliers
Vendor
Case Size
Inch (mm)
GRM155R60J225ME15 (CIN)
Murata
0402 (1005)
JMK105BJ225MV-F (CIN)
Taiyo Yuden
0402 (1005)
CL05A475MQ5NRNC (CIN or COUT)
Samsung
0402 (1005)
Model
Submit Documentation Feedback
Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM8801
13
LM8801
SNVS597H – APRIL 2009 – REVISED MAY 2013
www.ti.com
DSBGA PACKAGE ASSEMBLY AND USE
Use of the DSBGA package requires specialized board layout, precision mounting and careful re-flow
techniques, as detailed in Application Note 1112. Refer to the section Surface Mount Technology (SMD)
Assembly Considerations. For best results in assembly, alignment ordinals on the PC board should be used to
facilitate placement of the device.
The pad style used with DSBGA package must be the NSMD (Non-Solder Mask Defined) type. This means that
the solder-mask opening is larger than the pad size. This prevents a lip that otherwise forms if the solder-mask
and pad overlap, from holding the device off the surface of the board and interfering with mounting. See
Application Note 1112 for specific instructions how to do this.
BOARD LAYOUT CONSIDERATIONS
PC board layout is an important part of DC-DC converter design. Poor board layout can disrupt the performance
of a DC-DC converter and surrounding circuitry by contributing to EMI, ground bounce, and resistive voltage loss
in the traces. These can send erroneous signals to the DC-DC converter IC, resulting in poor regulation or
instability. Poor layout can also result in re-flow problems leading to poor solder joints between the DSBGA
package and board pads. Poor solder joints can result in erratic or degraded performance.
Good layout for the LM8801 can be implemented by following a few simple design rules, as illustrated in
Figure 24.
Input Capacitor
Enable Pin=0, part off
Enable Pin=1, part on
Output Capacitor
Inductor
Mode Pin=0, Auto mode
Mode Pin=1, PWM mode
Figure 24. LM8801 Board Layout (Top View)
1. Place the LM8801 on 8.26 mil pads. As a thermal relief, connect each pad with a 7 mil wide, approximately 7
mil long trace, and then incrementally increase each trace to its optimal width. The important criterion is
symmetry to ensure the solder bumps re-flow evenly. See AN-1112 DSBGA Wafer Level Chip Scale
Package (SNVA009).
2. Place the LM8801, inductor and filter capacitors close together and make the traces short. The traces
between these components carry relatively high switching currents and act as antennas. Following this rule
reduces radiated noise. Special care must be given to place the input filter capacitor very close to the VIN
and GND pin.
3. Arrange the components so that the switching current loops curl in the same direction. During the first half of
each cycle, current flows from the input filter capacitor, through the LM8801 and inductor to the output filter
capacitor and back through ground, forming a current loop. In the second half of each cycle, current is pulled
up from ground, through the LM8801 by the inductor, to the output filter capacitor and then back through
ground, forming a second current loop. Routing these loops so the current curls in the same direction
prevents magnetic field reversal between the two half-cycles and reduces radiated noise.
4. Connect the ground pins of the LM8801, and filter capacitors together using generous component-side
copper fill as a pseudo-ground plane. Then connect this to the ground-plane (if one is used) with several
vias. This reduces ground-plane noise by preventing the switching currents from circulating through the
ground plane. It also reduces ground bounce at the LM8801 by giving it a low-impedance ground connection.
5. Use wide traces between the power components and for power connections to the DC-DC converter circuit.
This reduces voltage errors caused by resistive losses across the traces.
14
Submit Documentation Feedback
Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM8801
LM8801
www.ti.com
SNVS597H – APRIL 2009 – REVISED MAY 2013
6. Route noise sensitive traces such as the voltage feedback path away from noisy traces between the power
components. The voltage feedback trace must remain close to the LM8801 circuit and should be routed
directly from FB to VOUT at the output capacitor and should be routed opposite to noise components. This
reduces EMI radiated onto the DC-DC converter’s own voltage feedback trace.
7. Place noise sensitive circuitry, such as radio IF blocks, away from the DC-DC converter, CMOS digital blocks
and other noisy circuitry. Interference with noise-sensitive circuitry in the system can be reduced through
distance.
In mobile phones, for example, a common practice is to place the DC-DC converter on one corner of the board,
arrange the CMOS digital circuitry around it (since this also generates noise), and then place sensitive
preamplifiers and IF stages on the diagonally opposing corner. Often, the sensitive circuitry is shielded with a
metal pan and power to it is post-regulated to reduce conducted noise, using low-dropout linear regulators.
Submit Documentation Feedback
Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM8801
15
LM8801
SNVS597H – APRIL 2009 – REVISED MAY 2013
www.ti.com
REVISION HISTORY
Changes from Revision G (May 2013) to Revision H
•
16
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 15
Submit Documentation Feedback
Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM8801
PACKAGE OPTION ADDENDUM
www.ti.com
13-Sep-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM8801TME-1.2/NOPB
ACTIVE
DSBGA
YFQ
6
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
J
LM8801TME-1.82/NOPB
ACTIVE
DSBGA
YFQ
6
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
LM8801TME-2.9/NOPB
ACTIVE
DSBGA
YFQ
6
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
S
LM8801TMX-1.2/NOPB
ACTIVE
DSBGA
YFQ
6
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
J
LM8801TMX-1.82/NOPB
ACTIVE
DSBGA
YFQ
6
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
LM8801TMX-2.9/NOPB
ACTIVE
DSBGA
YFQ
6
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
S
LM8801XUE-1.82/NOPB
ACTIVE
DSBGA
YQA
6
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
L
LM8801XUX-1.82/NOPB
ACTIVE
DSBGA
YQA
6
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
L
-30 to 85
-30 to 85
E
E
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
(4)
13-Sep-2014
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
8-May-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
LM8801TME-1.2/NOPB
DSBGA
YFQ
6
250
178.0
8.4
LM8801TME-1.82/NOPB
DSBGA
YFQ
6
250
178.0
LM8801TME-2.9/NOPB
DSBGA
YFQ
6
250
178.0
LM8801TMX-1.2/NOPB
DSBGA
YFQ
6
3000
LM8801TMX-1.82/NOPB
DSBGA
YFQ
6
W
Pin1
(mm) Quadrant
1.14
1.47
0.76
4.0
8.0
Q1
8.4
1.14
1.47
0.76
4.0
8.0
Q1
8.4
1.14
1.47
0.76
4.0
8.0
Q1
178.0
8.4
1.14
1.47
0.76
4.0
8.0
Q1
3000
178.0
8.4
1.14
1.47
0.76
4.0
8.0
Q1
LM8801TMX-2.9/NOPB
DSBGA
YFQ
6
3000
178.0
8.4
1.14
1.47
0.76
4.0
8.0
Q1
LM8801XUE-1.82/NOPB
DSBGA
YQA
6
250
178.0
8.4
1.15
1.35
0.4
4.0
8.0
Q1
LM8801XUX-1.82/NOPB
DSBGA
YQA
6
3000
178.0
8.4
1.15
1.35
0.4
4.0
8.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
8-May-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM8801TME-1.2/NOPB
DSBGA
YFQ
6
250
210.0
185.0
35.0
LM8801TME-1.82/NOPB
DSBGA
YFQ
6
250
210.0
185.0
35.0
LM8801TME-2.9/NOPB
DSBGA
YFQ
6
250
210.0
185.0
35.0
LM8801TMX-1.2/NOPB
DSBGA
YFQ
6
3000
210.0
185.0
35.0
LM8801TMX-1.82/NOPB
DSBGA
YFQ
6
3000
210.0
185.0
35.0
LM8801TMX-2.9/NOPB
DSBGA
YFQ
6
3000
210.0
185.0
35.0
LM8801XUE-1.82/NOPB
DSBGA
YQA
6
250
210.0
185.0
35.0
LM8801XUX-1.82/NOPB
DSBGA
YQA
6
3000
210.0
185.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
YFQ0006xxx
D
0.600±0.075
E
TMD06XXX (Rev B)
D: Max = 1.29 mm, Min = 1.23 mm
E: Max = 1.09 mm, Min = 1.03 mm
4215075/A
NOTES:
A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
www.ti.com
12/12
MECHANICAL DATA
YQA0006xxx
D
0.250±0.045
E
XUD06XXX (Rev A)
D: Max = 1.29 mm, Min = 1.23 mm
E: Max = 1.09 mm, Min = 1.03 mm
4215207/A
NOTES:
A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
www.ti.com
12/12
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
Similar pages