GSI GS82583ED18GK-675 8mb x 36 and 16mb x 18 organizations available Datasheet

GS82583ED18/36GK-675/625/550/500
288Mb SigmaQuad-IIIe™
Burst of 4 SRAM
260-Pin BGA
Commercial Temp
Industrial Temp
Up to 675 MHz
1.3V VDD
1.2V, 1.3V, or 1.5V VDDQ
Features
Clocking and Addressing Schemes
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The GS82583ED18/36GK SigmaQuad-IIIe SRAMs are
synchronous devices. They employ three pairs of positive and
negative input clocks; one pair of master clocks, CK and CK,
and two pairs of write data clocks, KD[1:0] and KD[1:0]. All
six input clocks are single-ended; that is, each is received by a
dedicated input buffer.
8Mb x 36 and 16Mb x 18 organizations available
675 MHz maximum operating frequency
675 MT/s peak transaction rate (in millions per second)
97 Gb/s peak data bandwidth (in x36 devices)
Separate I/O DDR Data Buses
Non-multiplexed SDR Address Bus
One operation - Read or Write - per clock cycle
Burst of 4 Read and Write operations
3 cycle Read Latency
1.3V nominal core voltage
1.2V, 1.3V, or 1.5V HSTL I/O interface
Configurable ODT (on-die termination)
ZQ pin for programmable driver impedance
ZT pin for programmable ODT impedance
IEEE 1149.1 JTAG-compliant Boundary Scan
260-pin, 14 mm x 22 mm, 1 mm ball pitch, 6/6 RoHS-
compliant BGA package
SigmaQuad-IIIe™ Family Overview
SigmaQuad-IIIe SRAMs are the Separate I/O half of the
SigmaQuad-IIIe/SigmaDDR-IIIe family of high performance
SRAMs. Although very similar to GSI's second generation of
networking SRAMs (the SigmaQuad-II/SigmaDDR-II family),
these third generation devices offer several new features that
help enable significantly higher performance.
CK and CK are used to latch address and control inputs, and to
control all output timing. KD[1:0] and KD[1:0] are used solely
to latch data inputs.
Each internal read and write operation in a SigmaQuad-IIIe B4
SRAM is four times wider than the device I/O bus. An input
data bus de-multiplexer is used to accumulate incoming data
before it is simultaneously written to the memory array. An
output data multiplexer is used to capture the data produced
from a single memory array read and then route it to the
appropriate output drivers as needed. Therefore, the address
field of a SigmaQuad-IIIe B4 SRAM is always two address
pins less than the advertised index depth (e.g. the 16M x 18 has
4M addressable index).
Parameter Synopsis
Speed Grade
Max Operating Frequency
Read Latency
VDD
-675
675 MHz
3 cycles
1.25V to 1.35V
-625
625 MHz
3 cycles
1.25V to 1.35V
-550
550 MHz
3 cycles
1.25V to 1.35V
-500
500 MHz
3 cycles
1.25V to 1.35V
Rev: 1.06 8/2017
1/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
16M x 18 Pinout (Top View)
5
6
7
8
1
2
3
4
9
10
11
12
13
A
VDD
VDDQ
VDD
VDDQ
NC
(RSVD)
MCH
(CFG)
MCL
ZQ
PZT1
VDDQ
VDD
VDDQ
VDD
B
VSS
NUO
VSS
NUI
MVQ
MCH
(B4M)
NC
(RSVD)
MCH
(SIOM)
PZT0
D0
VSS
Q0
VSS
C
Q17
VDDQ
D17
VDDQ
VSS
SA
VDD
SA
VSS
VDDQ
NUI
VDDQ
NUO
D
VSS
NUO
VSS
NUI
SA
VDDQ
SA
VDDQ
SA
D1
VSS
Q1
VSS
E
Q16
VDDQ
D16
VDD
VSS
SA
VSS
SA
VSS
VDD
NUI
VDDQ
NUO
F
VSS
NUO
VSS
NUI
SA
VDD
VDDQ
VDD
SA
D2
VSS
Q2
VSS
G
Q15
NUO
D15
NUI
VSS
SA
MZT1
SA
VSS
D3
NUI
Q3
NUO
H
Q14
VDDQ
D14
VDDQ
SA
VDDQ
W
VDDQ
SA
VDDQ
NUI
VDDQ
NUO
J
VSS
NUO
VSS
NUI
VSS
SA
VSS
SA
VSS
D4
VSS
Q4
VSS
K
CQ1
VDDQ
VREF
VDD
KD1
VDD
CK
VDD
KD0
VDD
VREF
VDDQ
CQ0
L
CQ1
VSS
QVLD1
Vss
KD1
VDDQ
CK
VDDQ
KD0
VSS
QVLD0
VSS
CQ0
M
VSS
Q13
VSS
D13
VSS
SA
VSS
SA
VSS
NUI
VSS
NUO
VSS
N
NUO
VDDQ
NUI
VDDQ
DLL
VDDQ
R
VDDQ
MCH
VDDQ
D5
VDDQ
Q5
P
NUO
Q12
NUI
D12
VSS
SA
MZT0
SA
VSS
NUI
D6
NUO
Q6
R
VSS
Q11
VSS
D11
MCH
VDD
VDDQ
VDD
RST
NUI
VSS
NUO
VSS
T
NUO
VDDQ
NUI
VDD
VSS
SA
VSS
SA
VSS
VDD
D7
VDDQ
Q7
U
VSS
Q10
VSS
D10
NC
(576 Mb)
VDDQ
NC
(RSVD)
VDDQ
NC
(1152 Mb)
NUI
VSS
NUO
VSS
V
NUO
VDDQ
NUI
VDDQ
VSS
SA
(x18)
VDD
NUI
(B2)
VSS
VDDQ
D8
VDDQ
Q8
W
VSS
Q9
VSS
D9
TCK
MCL
NC
(RSVD)
MCL
TMS
NUI
VSS
NUO
VSS
Y
VDD
VDDQ
VDD
VDDQ
TDO
ZT
NC
(RSVD)
MCL
TDI
VDDQ
VDD
VDDQ
VDD
Notes:
1. Pins 6W, 7A, 8W, and 8Y must be tied Low in this device.
2. Pins 5R and 9N must be tied High in this device.
3. Pin 6A is defined as mode pin CFG in the pinout standard. It must be tied High in this device to select x18 configuration.
4. Pin 8B is defined as mode pin SIOM in the pinout standard. It must be tied High in this device to select Separate I/O configuration.
5. Pin 6B is defined as mode pin B4M in the pinout standard. It must be tied High in this device to select Burst-of-4 configuration.
6. Pin 6V is defined as address pin SA for x18 devices. It is used in this device.
7. Pin 8V is defined as address pin SA for B2 devices. It is unused in this device, and must be left unconnected or driven Low.
8. Pin 5U is reserved as address pin SA for 576 Mb devices. It is a true no connect in this device.
9. Pin 9U is reserved as address pin SA for 1152 Mb devices. It is a true no connect in this device.
Rev: 1.06 8/2017
2/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
8M x 36 Pinout (Top View)
5
6
7
8
1
2
3
4
9
10
11
12
13
A
VDD
VDDQ
VDD
VDDQ
NC
(RSVD)
MCL
(CFG)
MCL
ZQ
PZT1
VDDQ
VDD
VDDQ
VDD
B
VSS
Q35
VSS
D35
MVQ
MCH
(B4M)
NC
(RSVD)
MCH
(SIOM)
PZT0
D0
VSS
Q0
VSS
C
Q26
VDDQ
D26
VDDQ
VSS
SA
VDD
SA
VSS
VDDQ
D9
VDDQ
Q9
D
VSS
Q34
VSS
D34
SA
VDDQ
SA
VDDQ
SA
D1
VSS
Q1
VSS
E
Q25
VDDQ
D25
VDD
VSS
SA
VSS
SA
VSS
VDD
D10
VDDQ
Q10
F
VSS
Q33
VSS
D33
SA
VDD
VDDQ
VDD
SA
D2
VSS
Q2
VSS
G
Q24
Q32
D24
D32
VSS
SA
MZT1
SA
VSS
D3
D11
Q3
Q11
H
Q23
VDDQ
D23
VDDQ
SA
VDDQ
W
VDDQ
SA
VDDQ
D12
VDDQ
Q12
J
VSS
Q31
VSS
D31
VSS
SA
VSS
SA
VSS
D4
VSS
Q4
VSS
K
CQ1
VDDQ
VREF
VDD
KD1
VDD
CK
VDD
KD0
VDD
VREF
VDDQ
CQ0
L
CQ1
VSS
QVLD1
VSS
KD1
VDDQ
CK
VDDQ
KD0
VSS
QVLD0
VSS
CQ0
M
VSS
Q22
VSS
D22
VSS
SA
VSS
SA
VSS
D13
VSS
Q13
VSS
N
Q30
VDDQ
D30
VDDQ
DLL
VDDQ
R
VDDQ
MCH
VDDQ
D5
VDDQ
Q5
P
Q29
Q21
D29
D21
VSS
SA
MZT0
SA
VSS
D14
D6
Q14
Q6
R
VSS
Q20
VSS
D20
MCH
VDD
VDDQ
VDD
RST
D15
VSS
Q15
VSS
T
Q28
VDDQ
D28
VDD
VSS
SA
VSS
SA
VSS
VDD
D7
VDDQ
Q7
U
VSS
Q19
VSS
D19
NC
(576 Mb)
VDDQ
NC
(RSVD)
VDDQ
NC
(1152 Mb)
D16
VSS
Q16
VSS
V
Q27
VDDQ
D27
VDDQ
VSS
NUI
(x18)
VDD
NUI
(B2)
VSS
VDDQ
D8
VDDQ
Q8
W
VSS
Q18
VSS
D18
TCK
MCL
NC
(RSVD)
MCL
TMS
D17
VSS
Q17
VSS
Y
VDD
VDDQ
VDD
VDDQ
TDO
ZT
NC
(RSVD)
MCL
TDI
VDDQ
VDD
VDDQ
VDD
Notes:
1. Pins 6W, 7A, 8W, and 8Y must be tied Low in this device.
2. Pins 5R and 9N must be tied High in this device.
3. Pin 6A is defined as mode pin CFG in the pinout standard. It must be tied Low in this device to select x36 configuration.
4. Pin 8B is defined as mode pin SIOM in the pinout standard. It must be tied High in this device to select Separate I/O configuration.
5. Pin 6B is defined as mode pin B4M in the pinout standard. It must be tied High in this device to select Burst-of-4 configuration.
6. Pin 6V is defined as address pin SA for x18 devices. It is unused in this device, and must be left unconnected or driven Low.
7. Pin 8V is defined as address pin SA for B2 devices. It is unused in this device, and must be left unconnected or driven Low.
8. Pin 5U is reserved as address pin SA for 576 Mb devices. It is a true no connect in this device.
9. Pin 9U is reserved as address pin SA for 1152 Mb devices. It is a true no connect in this device.
Rev: 1.06 8/2017
3/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
Pin Description
Symbol
Description
Type
Address — Read or Write Address is registered on CK.
Input
D[35:0]
Write Data — Registered on KD and KD during Write operations.
D[17:0] - x18 and x36.
D[35:18] - x36 only.
Input
Q[35:0]
Read Data — Aligned with CQ and CQ during Read operations.
Q[17:0] - x18 and x36.
Q[35:18] - x36 only.
Output
Read Data Valid — Driven high one half cycle before valid Read Data.
Output
SA
QVLD[1:0]
CK, CK
Primary Input Clocks — Dual single-ended. Used for latching address and control inputs, for internal timing
control, and for output timing control.
Input
KD[1:0],
KD[1:0]
Write Data Input Clocks — Dual single-ended. Used for latching write data inputs.
KD0, KD0: latch Write Data (D[17:0] in x36, D[8:0] in x18).
KD1, KD1: latch Write Data (D[35:18] in x36, D[17:9] in x18).
Input
CQ[1:0],
CQ[1:0]
Read Data Output Clocks — Free-running output (echo) clocks, tightly aligned with read data outputs.
Facilitate source-synchronous operation.
Output
R
Read Enable — Registered on CK. R = 0 initiates a Read operation.
Input
W
Write Enable — Registered on CK. W = 0 initiates a Write operation.
Input
DLL
DLL Enable — Weakly pulled High internally.
DLL = 0: disables internal DLL.
DLL = 1: enables internal DLL.
Input
RST
Reset — Holds the device inactive and resets the device to its initial power-on state when asserted High.
Weakly pulled Low internally.
Input
ZQ
Driver Impedance Control Resistor Input — Must be connected to VSS through an external resistor RQ to
program driver impedance.
Input
ZT
ODT Impedance Control Resistor Input — Must be connected to VSS through an external resistor RT to
program ODT impedance.
Input
MZT[1:0]
ODT Mode Select — Set the ODT state globally for all input groups. Must be tied High or Low.
MZT[1:0] = 00: disables ODT on all input groups, regardless of PZT[1:0].
MZT[1:0] = 01: enables strong ODT on select input groups, as specified by PZT[1:0].
MZT[1:0] = 10: enables weak ODT on select input groups, as specified by PZT[1:0].
MZT[1:0] = 11: reserved.
Input
PZT[1:0]
ODT Configuration Select — Set the ODT state for various combinations of input groups when MZT[1:0] =
01 or 10. Must be tied High or Low.
PZT[1:0] = 00: enables ODT on write data only.
PZT[1:0] = 01: enables ODT on write data and input clocks.
PZT[1:0] = 10: enables ODT on write data, address, and control.
PZT[1:0] = 11: enables ODT on write data, input clocks, address, and control.
Input
Rev: 1.06 8/2017
4/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
Symbol
Description
Type
MVQ
I/O Voltage Select — Indicates what voltage is supplied to the VDDQ pins. Must be tied High or Low.
MVQ = 0: Configure for 1.2V or 1.3V nominal VDDQ.
MVQ = 1: Configure for 1.5V nominal VDDQ.
VDD
Core Power Supply
—
VDDQ
I/O Power Supply
—
VREF
Input Reference Voltage — Input buffer reference voltage.
—
VSS
Ground
—
TCK
JTAG Clock — Weakly pulled Low internally.
Input
TMS
JTAG Mode Select — Weakly pulled High internally.
Input
TDI
JTAG Data Input — Weakly pulled High internally.
Input
TDO
JTAG Data Output
MCH
Must Connect High — May be tied to VDDQ directly or via a 1k resistor.
Input
MCL
Must Connect Low — May be tied to VSS directly or via a 1k resistor.
Input
NC
No Connect — There is no internal chip connection to these pins. They may be left unconnected, or tied/
driven High or Low.
NUI
Not Used Input — There is an internal chip connection to these input pins, but they are unused by the
device. They are pulled Low internally. They may be left unconnected or tied/driven Low. They should not be
tied/driven High.
Input
NUO
Not Used Output — There is an internal chip connection to these output pins, but they are unused by the
device. The drivers are tri-stated internally. They should be left unconnected.
Output
Rev: 1.06 8/2017
Input
Output
5/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
—
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
Power-Up and Reset Requirements
For reliability purposes, power supplies must power up simultaneously, or in the following sequence:
VSS, VDD, VDDQ, VREF and inputs.
Power supplies must power down simultaneously, or in the reverse sequence.
After power supplies power up, the following start-up sequence must be followed.
Step 1 (Recommended, but not required): Assert RST High for at least 1ms.
While RST is asserted high:
• The DLL is disabled.
• The states of R, and W control inputs are ignored.
Note: If possible, RST should be asserted High before input clocks begin toggling, and remain asserted High until input clocks are
stable and toggling within specification, in order to prevent unstable, out-of-spec input clocks from causing trouble in the SRAM.
Step 2: Begin toggling input clocks.
After input clocks begin toggling, but not necessarily within specification:
• Q are placed in the non-Read state, and remain so until the first Read operation.
• QVLD are driven Low, and remain so until the first Read operation.
• CQ, CQ begin toggling, but not necessarily within specification.
Step 3: Wait until input clocks are stable and toggling within specification.
Step 4: De-assert RST Low (if asserted High).
Step 5: Wait at least 160K (163,840) cycles.
During this time:
• Driver and ODT impedances are calibrated. Can take up to 160K cycles.
Note: The DLL pin may be asserted High or de-asserted Low during this time. If asserted High, DLL synchronization begins
immediately after the driver and ODT impedances are calibrated. If de-asserted Low, DLL synchronization begins after the DLL
pin is asserted High (see Step 6). In either case, Step 7 must follow thereafter.
Step 6: Assert DLL pin High (if de-asserted Low).
Step 7: Wait at least 64K (65,536) cycles for the DLL to lock.
After the DLL has locked:
• CQ, CQ begin toggling within specification.
Step 8: Begin initiating Read and Write operations.
Reset Usage
Although not generally recommended, RST may be asserted High at any time after completion of the initial power-up sequence
described above, to reset the SRAM control logic to its initial power-on state. However, whenever RST is subsequently de-asserted
Low (as in Step 4 above), Steps 5~7 above must be followed before Read and Write operations are initiated.
Note: Memory array content may be perturbed/corrupted when RST is asserted High.
Rev: 1.06 8/2017
6/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
DLL Operation
A DLL is implemented in these devices to control all output timing. It uses the CK input clock as a source, and is enabled when all
of the following conditions are met:
1. RST is de-asserted Low, and
2. The DLL pin is asserted High, and
3. CK cycle time  tKHKH (max), as specified in the AC Timing Specifications section.
Once enabled, the DLL requires 64K stable clock cycles in order to lock/synchronize properly.
When the DLL is enabled, it aligns output clocks and read data to input clocks, and it generates all mid-cycle output timing. See the
Output Timing section for more information.
The DLL can tolerate changes in input clock frequency due to clock jitter (i.e. such jitter will not cause the DLL to lose lock/
synchronization), provided the cycle-to-cycle jitter does not exceed 200ps (see “tKJITcc” in the AC Timing Specifications section
for more information). However, the DLL must be resynchronized (i.e. disabled and then re-enabled) whenever the nominal input
clock frequency is changed.
The DLL is disabled when any of the following conditions are met:
1. RST is asserted High, or
2. The DLL pin is de-asserted Low, or
3. CK is stopped for at least 30ns, or CK cycle time  30ns.
Clock Truth Table
Previous
Operation
SA
R
W
Current Operation
(tn–1)
CK
(tn)
CK
(tn)
CK
(tn)
(tn)
KD
(tn+1)
KD
(tn+1½)
KD
(tn+2)
KD
(tn+2½)
NOP
X
1
1
NOP
X
X
—
—
0 / High-Z
—
Write
X
1
X
NOP
D3
D4
—
—
0 / High-Z
—
Read
X
X
1
NOP
X
X
—
—
NOP
V
1
0
Write
D1
D2
D3
D4
Read
V
X
0
Write
D1
D2
D3
D4
Q3
Q4
NOP
V
0
X
Read
X
X
—
—
Q1
Q2
Q3
Q4
Write
V
0
X
Read
D3
D4
—
—
Q1
Q2
Q3
Q4
D
Q
CQ
(tn+3)
Q3
CQ
(tn+3½)
CQ
(tn+4)
Q4
CQ
(tn+4½)
—
0 / High-Z
—
—
Notes:
1. 1 = High; 0 = Low; V = Valid; X = don’t care.
2. D1, D2, D3, and D4 indicate the first, second, third, and fourth pieces of Write Data transferred during Write operations.
3. Q1, Q2, Q3, and Q4 indicate the first, second, third, and fourth pieces of Read Data transferred during Read operations.
4. When D ODT is enabled, Q pins are driven Low for one cycle in response to NOP and Write commands, 3 cycles after the command is
sampled, except when preceded by a Read command. When D ODT is disabled, Q pins are tri-stated for one cycle in response to NOP
and Write commands, 3 cycles after the command is sampled, except when preceded by a Read command.
Rev: 1.06 8/2017
7/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
Input Timing
These devices utilize three pairs of positive and negative input clocks, CK & CK and KD[1:0] & KD[1:0], to latch the various
synchronous inputs. Specifically:
CK latches all address (SA) inputs.
CK latches all control (R, W) inputs.
KD[1:0] and KD[1:0] latch particular write data (D) inputs, as follows:
• KD0 and KD0 latch D[17:0] in x36, and D[8:0] in x18.
• KD1 and KD1 latch D[35:18] in x36, and D[17:9] in x18.
Output Timing
These devices provide two pairs of positive and negative output clocks (aka “echo clocks”), CQ[1:0] & CQ[1:0], whose timing is
tightly aligned with read data in order to enable reliable source-synchronous data transmission.
These devices utilize a DLL to control output timing. When the DLL is enabled, it generates 0 and 180 phase clocks from CK
that control read data output clock (CQ, CQ), read data (Q), and read data valid (QVLD) output timing, as follows:
• CK+0 generates CQ[1:0], CQ[1:0], Q1 active, and Q2 inactive.
• .CK+180 generates CQ[1:0], CQ[1:0], Q1 inactive, Q2 active, and QVLD active/inactive.
Note: Q1 and Q2 indicate the first and second pieces of read data transferred in any given clock cycle during Read operations.
When the DLL is enabled, CQ is aligned to CK. See the AC Timing Specifications for more information.
CQ[1:0] and CQ[1:0] align with particular Q and QVLD outputs, as follows:
• CQ0 and CQ0 align with Q[17:0], QVLD0 in x36 devices, and Q[8:0], QVLD0 in x18 devices.
• CQ1 and CQ1 align with Q[35:18], QVLD1 in x36 devices, and Q[17:9], QVLD0 in x18 devices.
Rev: 1.06 8/2017
8/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
Driver Impedance Control
Programmable Driver Impedance is implemented on the following output signals:
• CQ, CQ, Q, QVLD.
Driver impedance is programmed by connecting an external resistor RQ between the ZQ pin and VSS.
Driver impedance is set to the programmed value within 160K cycles after input clocks are operating within specification and RST
is de-asserted Low. It is updated periodically thereafter to compensate for temperature and voltage fluctuations in the system.
Output Signal
Pull-Down Impedance (ROUTL)
Pull-Up Impedance (ROUTH)
CQ, CQ, Q, QVLD
RQ*0.2  15%
RQ*0.2  15%
Notes:
1. ROUTL and ROUTH apply when 175 RQ  225.
2. The mismatch between ROUTL and ROUTH is less than 10%, guaranteed by design.
ODT Impedance Control
Programmable ODT Impedance is implemented on the following input signals:
• CK, CK, KD, KD, SA, R, W, D.
ODT impedance is programmed by connecting an external resistor RT between the ZT pin and VSS.
ODT impedance is set to the programmed value within 160K cycles after input clocks are operating within specification and RST
is de-asserted Low. It is updated periodically thereafter to compensate for temperature and voltage fluctuations in the system
Input Signal
CK, CK, KD, KD
PZT[1:0]
MZT[1:0]
Pull-Down Impedance (RINL)
Pull-Up Impedance (RINH)
X0
XX
disabled
disabled
01
RT  15%
RT  15%
10
RT*2  20%
RT*2  20%
XX
disabled
disabled
01
RT  15%
RT  15%
10
RT*2  20%
RT*2  20%
01
RT  15%
RT  15%
10
RT*2  20%
RT*2  20%
X1
0X
SA, R, W
D
1X
XX
Notes:
1. When MZT[1:0] = 00, ODT is disabled on all inputs. MZT[1:0] = 11 is reserved for future use.
2. RINL and RINH apply when 105 RT  135
3. The mismatch between RINL and RINH is less than 10%, guaranteed by design.
4. All ODT is disabled during JTAG EXTEST and SAMPLE-Z instructions.
Note: When ODT impedance is enabled on a particular input, that input should always be driven High or Low; it should never be
tri-stated (i.e., in a High- Z state). If the input is tri-stated, the ODT will pull the signal to VDDQ / 2 (i.e., to the switch point of the
diff-amp receiver), which could cause the receiver to enter a meta-stable state and consume more power than it normally would.
This could result in the device’s operating currents being higher.
Rev: 1.06 8/2017
9/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
Absolute Maximum Ratings
Parameter
Symbol
Rating
Units
Core Supply Voltage
VDD
-0.3 to +1.4
V
I/O Supply Voltage when MVQ = 0
VDDQ
-0.3 to VDD
V
I/O Supply Voltage when MVQ = 1
VDDQ
-0.3 to +1.8
Input Voltage
VIN
-0.3 to VDDQ + 0.3
V
Junction Temperature
TJ
0 to 125
C
Storage Temperature
TSTG
-55 to 125
C
Notes
Note: Permanent damage to the device may occur if the Absolute Maximum Ratings are exceeded. Operation should be restricted to Recommended Operating Conditions. Exposure to conditions exceeding the Recommended Operating Conditions for an extended period of time may
affect reliability of this component.
Recommended Operating Conditions
Parameter
Symbol
Min
Typ
Max
Units
Core Supply Voltage
VDD
1.25
1.3
1.35
V
I/O Supply Voltage when MVQ = 0
VDDQ
1.15
1.2 or 1.3
VDD
V
I/O Supply Voltage when MVQ = 1
VDDQ
1.45
1.5
1.55
V
Commercial Junction Temperature
TJC
0
—
85
C
Industrial Junction Temperature
TJI
-40
—
100
C
Notes
Note: For reliability purposes, power supplies must power up simultaneously, or in the following sequence:
VSS, VDD, VDDQ, VREF, and Inputs.
Power supplies must power down simultaneously, or in the reverse sequence.
Thermal Impedances
Package
JA (C°/W)
Airflow = 0 m/s
 JA (C°/W)
Airflow = 1 m/s
 JA (C°/W)
Airflow = 2 m/s
JB (C°/W)
 JC (C°/W)
FBGA
12.94
10.47
9.51
2.93
0.33
Rev: 1.06 8/2017
10/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
I/O Capacitance
Parameter
Symbol
Min
Max
Units
Notes
Input Capacitance
CIN
—
5.0
pF
1, 3
Output Capacitance
COUT
—
5.5
pF
2, 3
Notes:
1. VIN = VDDQ/2.
2. VOUT = VDDQ/2.
3. TA = 25C, f = 1 MHz.
Input Electrical Characteristics - 1.2V or 1.3V I/O (MVQ = 0)
Parameter
Symbol
Min
Typ
Max
Units
Notes
DC Input Reference Voltage
VREFdc
0.48 * VDDQ
0.50 * VDDQ
0.52 * VDDQ
V
—
DC Input High Voltage (HS)
VIH1dc
VREF + 0.08
0.80 * VDDQ
VDDQ + 0.15
V
1, 6
DC Input Low Voltage (HS)
VIL1dc
-0.15
0.20 * VDDQ
VREF - 0.08
V
2, 6
DC Input High Voltage (LS)
VIH2dc
0.75 * VDDQ
VDDQ
VDDQ + 0.15
V
7
DC Input Low Voltage (LS)
VIL2dc
-0.15
0
0.25 * VDDQ
V
7
AC Input Reference Voltage
VREFac
0.47 * VDDQ
0.50 * VDDQ
0.53 * VDDQ
V
3
AC Input High Voltage (HS)
VIH1ac
VREF + 0.15
0.80 * VDDQ
VDDQ + 0.25
V
1, 4~6
AC Input Low Voltage (HS)
VIL1ac
-0.25
0.20 * VDDQ
VREF - 0.15
V
2, 4~6
AC Input High Voltage (LS)
VIH2ac
VDDQ - 0.2
VDDQ
VDDQ + 0.25
V
4, 7
AC Input Low Voltage (LS)
VIL2ac
-0.25
0
0.2
V
4, 7
Notes:
1. “Typ” parameter applies when Controller ROUTH = 40 and SRAM RINH = RINL = 120.
2. “Typ” parameter applies when Controller ROUTL = 40 and SRAM RINH = RINL = 120.
3. VREFac is equal to VREFdc plus noise.
4. VIH max and VIL min apply for pulse widths less than one-quarter of the cycle time.
5. Input rise and fall times must be a minimum of 1V/ns, and within 10% of each other.
6. Parameters apply to High Speed Inputs: CK, CK, KD, KD, SA, D, R, W.
7. Parameters apply to Low Speed Inputs: RST, DLL, MZT, PZT, MVQ.
Rev: 1.06 8/2017
11/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
Input Electrical Characteristics - 1.5V I/O (MVQ = 1)
Parameter
Symbol
Min
Typ
Max
Units
Notes
DC Input Reference Voltage
VREFdc
0.48 * VDDQ
0.50 * VDDQ
0.52 * VDDQ
V
—
DC Input High Voltage (HS)
VIH1dc
VREF + 0.1
0.80 * VDDQ
VDDQ + 0.15
V
1, 6
DC Input Low Voltage (HS)
VIL1dc
-0.15
0.20 * VDDQ
VREF - 0.1
V
2, 6
DC Input High Voltage (LS)
VIH2dc
0.75 * VDDQ
VDDQ
VDDQ + 0.15
V
7
DC Input Low Voltage (LS)
VIL2dc
-0.15
0
0.25 * VDDQ
V
7
AC Input Reference Voltage
VREFac
0.47 * VDDQ
0.50 * VDDQ
0.53 * VDDQ
V
3
AC Input High Voltage (HS)
VIH1ac
VREF + 0.2
0.80 * VDDQ
VDDQ + 0.25
V
1, 4~6
AC Input Low Voltage (HS)
VIL1ac
-0.25
0.20 * VDDQ
VREF - 0.2
V
2, 4~6
AC Input High Voltage (LS)
VIH2ac
VDDQ - 0.2
VDDQ
VDDQ + 0.25
V
4, 7
AC Input Low Voltage (LS)
VIL2ac
-0.25
0
0.2
V
4, 7
Notes:
1. “Typ” parameter applies when Controller ROUTH = 40 and SRAM RINH = RINL = 120.
2. “Typ” parameter applies when Controller ROUTL = 40 and SRAM RINH = RINL = 120.
3. VREFac is equal to VREFdc plus noise.
4. VIH max and VIL min apply for pulse widths less than one-quarter of the cycle time.
5. Input rise and fall times must be a minimum of 1V/ns, and within 10% of each other.
6. Parameters apply to High Speed Inputs: CK, CK, KD, KD, SA, D, R, W.
7. Parameters apply to Low Speed Inputs: RST, DLL, MZT, PZT, MVQ.
Output Electrical Characteristics
Parameter
Symbol
Min
Typ
Max
Units
Notes
DC Output High Voltage
VOHdc
—
0.80 * VDDQ
VDDQ + 0.15
V
1, 3
DC Output Low Voltage
VOLdc
-0.15
0.20 * VDDQ
—
V
2, 3
AC Output High Voltage
VOHac
—
0.80 * VDDQ
VDDQ + 0.25
V
1, 3
AC Output Low Voltage
VOLac
-0.25
0.20 * VDDQ
—
V
2, 3
Note:
1. “Typ” parameter applies when SRAM ROUTH = 40 and Controller RINH = RINL = 120.
2. “Typ” parameter applies when SRAM ROUTL = 40 and Controller RINH = RINL = 120.
3. Parameters apply to: CQ, CQ, Q, QVLD.
Rev: 1.06 8/2017
12/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
Leakage Currents
Parameter
Input Leakage Current
Output Leakage Current
Symbol
Min
Max
Units
Notes
ILI1
-2
2
uA
1, 2
ILI2
-20
2
uA
1, 3
ILI3
-2
20
uA
1, 4
ILO
-2
2
uA
5, 6
Notes:
1. VIN = VSS to VDDQ.
2. Parameters apply to CK, CK, KD, KD, SA, D, R, W when ODT is disabled.
Parameters apply to MZT, PZT, MVQ.
3. Parameters apply to DLL, TMS, TDI (weakly pulled up).
4. Parameters apply to RST, TCK (weakly pulled down).
5. VOUT = VSS to VDDQ.
6. Parameters apply to CQ, CQ, Q, QVLD, TDO.
Operating Currents
Parameter
Symbol
VDD (nom)
500 MHz
550 MHz
625 MHz
675 MHz
Units
x18 Operating Current
IDD
1.3V
1200
1300
1450
1550
mA
x36 Operating Current
IDD
1.3V
1360
1480
1660
1780
mA
Notes:
1. IOUT = 0 mA; VIN = VIH or VIL.
2. Applies at 100% alternating Reads and Writes.
Rev: 1.06 8/2017
13/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
AC Test Conditions - 1.2V I/O (MVQ = 0)
Parameter
Symbol
Conditions
Units
Core Supply Voltage
VDD
1.25 to 1.35
V
I/O Supply Voltage
VDDQ
1.15 to 1.25
V
Input Reference Voltage
VREF
0.6
V
Input High Level
VIH
0.9
V
Input Low Level
VIL
0.3
V
Input Rise and Fall Time
—
2.0
V/ns
Input and Output Reference Level
—
0.6
V
Parameter
Symbol
Conditions
Units
Core Supply Voltage
VDD
1.25 to 1.35
V
I/O Supply Voltage
VDDQ
1.45 to 1.55
V
Input Reference Voltage
VREF
0.75
V
Input High Level
VIH
1.25
V
Input Low Level
VIL
0.25
V
Input Rise and Fall Time
—
2.0
V/ns
Input and Output Reference Level
—
0.75
V
Note: Output Load Conditions RQ = 200. Refer to figure below.
AC Test Conditions - 1.5V I/O (MVQ = 1)
Note: Output Load Conditions RQ = 200. Refer to figure below.
AC Test Output Load
50
Output
50
VDDQ/2
5 pF
Rev: 1.06 8/2017
14/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
AC Timing Specifications (independent of device speed grade)
Parameter
Symbol
Min
Max
Units Notes
Input Clock Timing
Clk High Pulse Width
tKHKL
0.45
—
cycles
1
Clk Low Pulse Width
tKLKH
0.45
—
cycles
1
Clk High to Clk High
tKHKH
0.45
0.55
cycles
2
Clk High to Write Data Clk High
tKHKDH
-200
+200
ps
3
Clk Cycle-to-Cycle Jitter
tKJITcc
—
60
ps
1,4,5
DLL Lock Time
tKlock
65,536
—
cycles
6
Clk Static to DLL Reset
tKreset
30
—
ns
7,12
Output Timing
Clk High to Output Valid / Hold
tKHQV/X
-0.4
+0.4
ns
8
Clk High to Echo Clock High
tKHCQH
-0.4
+0.4
ns
9
Echo Clk High to Output Valid / Hold
tCQHQV/X
-150
+150
ps
10,12
Echo Clk High to Echo Clock High
tCQHCQH
tKHKH (min) - 100
tKHKH (max) + 100
ps
11,12
Notes:
All parameters are measured from the mid-point of the object signal to the mid-point of the reference signal.
1. Parameters apply to CK, CK, KD, KD.
2. Parameter specifiesCK CK and KD KD requirements.
3. Parameter specifies CK KD and CK KD requirements.
4. Parameter specifies Cycle-to-Cycle (C2C) Jitter (i.e. the maximum variation from clock rising edge to the next clock rising edge). 
As such, it limits Period Jitter (i.e. the maximum variation in clock cycle time from nominal) to  30ps. 
And as such, it limits Absolute Jitter (i.e. the maximum variation in clock rising edge from its nominal position) to  15ps.
5. The device can tolerated C2C Jitter greater than 60ps, up to a maximum of 200ps. However, when using a device from a particular speed
grade, tKHKH (min) of that speed grade must be derated (increased) by half the difference between the actual C2C Jitter and 60ps. For
example, if the actual C2C Jitter is 100ps, then tKHKH (min) for the -675 speed grade is derated to 1.5ns (1.48ns + 0.5*(100ps - 60ps)).
6. VDD slew rate must be < 0.1V DC per 50ns for DLL lock retention. DLL lock time begins once VDD and input clock are stable.
7. Parameter applies to CK.
8. Parameters apply to Q, and are referenced to CK.
9. Parameter specifies CK CQ timing.
10. Parameters apply to Q, QVLD and are referenced to CQ & CQ.
11. Parameter specifies CQ CQ timing.
12. Parameters are not tested. They are guaranteed by design, and verified through extensive corner-lot characterization.
Rev: 1.06 8/2017
15/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
AC Timing Specifications (variable with device speed grade)
Parameter
Symbol
–675
Min
–625
Max
Min
–550
Max
–500
Units Notes
Min
Max
Min
Max
1.8
6.0
2.0
6.0
ns
Input Clock Timing
Clk Cycle Time
tKHKH
1.48
6.0
1.6
6.0
1
Input Setup & Hold Timing
Input Valid to Clk High
tIVKH
150
—
160
—
180
—
200
—
ps
Clk High to Input Hold
tKHIX
150
—
160
—
180
—
200
—
ps
2
Notes:
All parameters are measured from the mid-point of the object signal to the mid-point of the reference signal.
1. Parameters apply to CK, CK, KD, KD.
2. Parameters apply to SA, and are referenced to CK.
Parameters apply to R, W, and are referenced to CK.
Parameters apply to D, and are referenced to KD & KD.
Rev: 1.06 8/2017
16/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
Read and Write Timing Diagram
Read
Write
Read
NOP
NOP
Write
Read
Write
Read
Write
NOP
KD
tKHKH
tKHKL tKLKH tKHKH
KD
tIVKH
D
tKHKDH
D21
D22
D23
D24
tKHIX
D41
D42
D43
D44
tIVKH
D61
D62
tKHIX
D63
D64
D81
tKHKDH
CK
tKHKH
tKHKL tKLKH tKHKH
CK
tIVKH tKHIX
SA A1
A2
A3
A4
A5
A6
A7
A8
tIVKH tKHIX
R
W
tKHQV
Q
tKHQX
Q11
Q12
Q13
Q14
Q31
Q32
Q33
Q34
Q51
Q52
Q53
QVLD
tCQHQX
tKHCQH
tCQHQV
tCQHQX
tCQHQX
tCQHQV
tCQHQV
CQ
tCQHCQH
CQ
Rev: 1.06 8/2017
17/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
JTAG Test Mode Description
These devices provide a JTAG Test Access Port (TAP) and Boundary Scan interface using a limited set of IEEE std. 1149.1
functions. This test mode is intended to provide a mechanism for testing the interconnect between master (processor, controller,
etc.), SRAM, other components, and the printed circuit board. In conformance with a subset of IEEE std. 1149.1, these devices
contain a TAP Controller and multiple TAP Registers. The TAP Registers consist of one Instruction Register and multiple Data
Registers.
The TAP consists of the following four signals:
Pin
Pin Name
I/O
Description
TCK
Test Clock
I
Induces (clocks) TAP Controller state transitions.
TMS
Test Mode Select
I
Inputs commands to the TAP Controller.
Sampled on the rising edge of TCK.
TDI
Test Data In
I
Inputs data serially to the TAP Registers.
Sampled on the rising edge of TCK.
TDO
Test Data Out
O
Outputs data serially from the TAP Registers.
Driven from the falling edge of TCK.
Concurrent TAP and Normal SRAM Operation
According to IEEE std. 1149.1, most public TAP Instructions do not disrupt normal device operation. In these devices, the only
exceptions are EXTEST and SAMPLE-Z. See the Tap Registers section for more information.
Disabling the TAP
When JTAG is not used, TCK should be tied Low to prevent clocking the SRAM. TMS and TDI should either be tied High through
a pull-up resistor or left unconnected. TDO should be left unconnected.
JTAG DC Operating Conditions
Parameter
Symbol
Min
Max
Units
Notes
JTAG Input High Voltage
VTIH
0.75 * VDDQ
VDDQ + 0.15
V
1
JTAG Input Low Voltage
VTIL
–0.15
0.25 * VDDQ
V
1
JTAG Output High Voltage
VTOH
VDDQ – 0.2
—
V
2, 3
JTAG Output Low Voltage
VTOL
—
0.2
V
2, 4
Notes:
1. Parameters apply to TCK, TMS, and TDI.
2. Parameters apply to TDO.
3. ITOH = –2.0 mA.
4. ITOL = 2.0 mA.
Rev: 1.06 8/2017
18/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
JTAG AC Timing Specifications
Parameter
Symbol
Min
Max
Units
TCK Cycle Time
tTHTH
50
—
ns
TCK High Pulse Width
tTHTL
20
—
ns
TCK Low Pulse Width
tTLTH
20
—
ns
TMS Setup Time
tMVTH
10
—
ns
TMS Hold Time
tTHMX
10
—
ns
TDI Setup Time
tDVTH
10
—
ns
TDI Hold Time
tTHDX
10
—
ns
Capture Setup Time (Address, Control, Data, Clock)
tCS
10
—
ns
Capture Hold Time (Address, Control, Data, Clock)
tCH
10
—
ns
TCK Low to TDO Valid
tTLQV
—
10
ns
TCK Low to TDO Hold
tTLQX
0
—
ns
JTAG Timing Diagram
tTHTL
tTLTH
tTHTH
TCK
tMVTH tTHMX
TMS
tDVTH tTHDX
TDI
tTLQV
tTLQX
TDO
Rev: 1.06 8/2017
19/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
TAP Controller
The TAP Controller is a 16-state state machine that controls access to the various TAP Registers and executes the operations
associated with each TAP Instruction. State transitions are controlled by TMS and occur on the rising edge of TCK.
The TAP Controller enters the Test-Logic Reset state in one of two ways:
1. At power up.
2. When a logic 1 is applied to TMS for at least 5 consecutive rising edges of TCK.
The TDI input receiver is sampled only when the TAP Controller is in either the Shift-IR state or the Shift-DR state.
The TDO output driver is enabled only when the TAP Controller is in either the Shift-IR state or the Shift-DR state.
TAP Controller State Diagram
1
Test-Logic Reset
0
0
Run-Test / Idle
1
Select DR-Scan
1
Select IR-Scan
0
0
1
1
Capture-DR
Capture-IR
0
0
0
Shift-DR
1
1
Exit1-DR
Exit1-IR
0
0
0
Pause-DR
1
0
Exit2-IR
Update-DR
Rev: 1.06 8/2017
0
20/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
0
1
1
1
0
Pause-IR
1
Exit2-DR
0
Shift-IR
1
1
1
Update-IR
1
0
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
TAP Registers
TAP Registers are serial shift registers that capture serial input data (from TDI) on the rising edge of TCK, and drive serial output
data (to TDO) on the subsequent falling edge of TCK. They are divided into two groups: Instruction Registers (IR), which are
manipulated via the IR states in the TAP Controller, and Data Registers (DR), which are manipulated via the DR states in the TAP
Controller.
Instruction Register (IR - 3 bits)
The Instruction Register stores the various TAP Instructions supported by SRAM. It is loaded with the IDCODE instruction (logic
001) at power-up, and when the TAP Controller is in the Test-Logic Reset and Capture-IR states. It is inserted between TDI and
TDO when the TAP Controller is in the Shift-IR state, at which time it can be loaded with a new instruction. However, newly
loaded instructions are not executed until the TAP Controller has reached the Update-IR state.
The Instruction Register is 3 bits wide, and is encoded as follows:
Code
(2:0)
Instruction
Description
EXTEST
Loads the logic states of all signals composing the SRAM I/O ring into the Boundary Scan Register
when the TAP Controller is in the Capture-DR state, and inserts the Boundary Scan Register between
TDI and TDO when the TAP Controller is in the Shift-DR state.
Also transfers the contents of the Boundary Scan Register associated with output signals (Q, QVLD,
CQ, CQ) directly to their corresponding output pins. However, newly loaded Boundary Scan Register
contents do not appear at the output pins until the TAP Controller has reached the Update-DR state.
Also disables all ODT.
See the Boundary Scan Register description for more information.
IDCODE
Loads a predefined device- and manufacturer-specific identification code into the ID Register when the
TAP Controller is in the Capture-DR state, and inserts the ID Register between TDI and TDO when the
TAP Controller is in the Shift-DR state.
See the ID Register description for more information.
010
SAMPLE-Z
Loads the logic states of all signals composing the SRAM I/O ring into the Boundary Scan Register
when the TAP Controller is in the Capture-DR state, and inserts the Boundary Scan Register between
TDI and TDO when the TAP Controller is in the Shift-DR state.
Also disables all ODT.
Also forces Q output drivers to a High-Z state.
See the Boundary Scan Register description for more information.
011
PRIVATE
Reserved for manufacturer use only.
100
SAMPLE
Loads the logic states of all signals composing the SRAM I/O ring into the Boundary Scan Register
when the TAP Controller is in the Capture-DR state, and inserts the Boundary Scan Register between
TDI and TDO when the TAP Controller is in the Shift-DR state.
See the Boundary Scan Register description for more information.
101
PRIVATE
Reserved for manufacturer use only.
110
PRIVATE
Reserved for manufacturer use only.
111
BYPASS
Loads a logic 0 into the Bypass Register when the TAP Controller is in the Capture-DR state, and
inserts the Bypass Register between TDI and TDO when the TAP Controller is in the Shift-DR state.
See the Bypass Register description for more information.
000
001
Rev: 1.06 8/2017
21/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
Bypass Register (DR - 1 bit)
The Bypass Register is one bit wide, and provides the minimum length serial path between TDI and TDO. It is loaded with a logic
0 when the BYPASS instruction has been loaded in the Instruction Register and the TAP Controller is in the Capture-DR state. It is
inserted between TDI and TDO when the BYPASS instruction has been loaded into the Instruction Register and the TAP
Controller is in the Shift-DR state.
ID Register (DR - 32 bits)
The ID Register is loaded with a predetermined device- and manufacturer-specific identification code when the IDCODE
instruction has been loaded into the Instruction Register and the TAP Controller is in the Capture-DR state. It is inserted between
TDI and TDO when the IDCODE instruction has been loaded into the Instruction Register and the TAP Controller is in the
Shift-DR state.
The ID Register is 32 bits wide, and is encoded as follows:
See BSDL Model
(31:12)
GSI ID
(11:1)
Start Bit
(0)
XXXX XXXX XXXX XXXX XXXX
0001 1011 001
1
Bit 0 is the LSB of the ID Register, and Bit 31 is the MSB. When the ID Register is selected, TDI serially shifts data into the MSB,
and the LSB serially shifts data out through TDO.
Boundary Scan Register (DR - 129 bits)
The Boundary Scan Register is equal in length to the number of active signal connections to the SRAM (excluding the TAP pins)
plus a number of place holder locations reserved for functional and/or density upgrades. It is loaded with the logic states of all
signals composing the SRAM’s I/O ring when the EXTEST, SAMPLE, or SAMPLE-Z instruction has been loaded into the
Instruction Register and the TAP Controller is in the Capture-DR state. It is inserted between TDI and TDO when the EXTEST,
SAMPLE, or SAMPLE-Z instruction has been loaded into the Instruction Register and the TAP Controller is in the Shift-DR state.
Additionally, the contents of the Boundary Scan Register associated with the SRAM outputs (Q, QVLD, CQ, CQ) are driven
directly to the corresponding SRAM output pins when the EXTEST instruction is selected. However, after the EXTEST instruction
has been selected, any new data loaded into Boundary Scan Register when the TAP Controller is in the Shift-DR state does not
appear at the output pins until the TAP Controller has reached the Update-DR state.
The value captured in the boundary scan register for NU pins is determined by the external pin state. The value captured in the
boundary scan register for NC pins is 0 regardless of the external pin state. The value captured in the Internal Cell (Bit 129) is 1.
Output Driver State During EXTEST
EXTEST allows the Internal Cell (Bit 129) in the Boundary Scan Register to control the state of Q drivers. That is, when Bit 129 =
1, Q drivers are enabled (i.e., driving High or Low), and when Bit 129 = 0, Q drivers are disabled (i.e., forced to High-Z state). See
the Boundary Scan Register section for more information.
ODT State During EXTEST and SAMPLE-Z
ODT on all inputs is disabled during EXTEST and SAMPLE-Z.
Rev: 1.06 8/2017
22/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
Boundary Scan Register Bit Order Assignment
The table below depicts the order in which the bits are arranged in the Boundary Scan Register. Bit 1 is the LSB and Bit 129 is the
MSB. When the Boundary Scan Register is selected, TDI serially shifts data into the MSB, and the LSB serially shifts data out
through TDO.
Bit
Pad
Bit
Pad
Bit
Pad
Bit
Pad
Bit
Pad
1
7L
29
12F
57
12W
85
1T
113
1C
2
7K
30
11G
58
10W
86
4R
114
3C
3
9L
31
13G
59
8V
87
2R
115
2B
4
9K
32
10G
60
9U
88
3P
116
4B
5
8J
33
12G
61
8T
89
1P
117
5A
6
7H
34
11H
62
9R
90
4P
118
6A
7
9H
35
13H
63
8P
91
2P
119
6B
8
7G
36
10J
64
9N
92
3N
120
6C
9
8G
37
12J
65
8M
93
1N
121
5D
10
9F
38
13K
66
6M
94
4M
122
6E
11
8E
39
13L
67
7N
95
2M
123
5F
12
7D
40
11L
68
5N
96
3L
124
6G
13
9D
41
12M
69
7P
97
1L
125
5H
14
8C
42
10M
70
6P
98
1K
126
6J
15
7B
43
13N
71
5R
99
2J
127
5K
16
8B
44
11N
72
6T
100
4J
128
5L
17
9B
45
12P
73
7U
101
1H
129
Internal
18
7A
46
10P
74
5U
102
3H
19
9A
47
13P
75
6V
103
2G
20
10B
48
11P
76
6W
104
4G
21
12B
49
12R
77
7Y
105
1G
22
11C
50
10R
78
4W
106
3G
23
13C
51
13T
79
2W
107
2F
24
10D
52
11T
80
3V
108
4F
25
12D
53
12U
81
1V
109
1E
26
11E
54
10U
82
4U
110
3E
27
13E
55
13V
83
2U
111
2D
28
10F
56
11V
84
3T
112
4D
Rev: 1.06 8/2017
23/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
260-Pin BGA Package Drawing (Package GK)
0.08 S C
0.22 S C A S B S
Ø
Ø
Ø
0.50~Ø0.70(260x)
13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
19.00
17.40  0.05
22.00  0.05
1.00
PIN #1 CORNER
13.20  0.05
B
A
1.00
14.00  0.05
12.00
Rev: 1.06 8/2017
C
0.15
0.05
SEATING PLANE
0.40~0.60
0.51 REF
C
4–R0.5 (MAX)
0.50 + 0.03
0.10
HEAT SPREADER
//
1.09 REF
C
2.10 + 0.2/–0.3
0.06
0.05(4X)
Ball Pitch:
1.00 Substrate Thickness:
Ball Diameter:
0.60 Mold Thickness:
0.51
—
24/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
Ordering Information — GSI SigmaQuad-IIIe SRAM
Org
Part Number
Type
Package
Speed
(MHz)
TA
16M x 18
GS82583ED18GK-675
SigmaQuad-IIIe B4
ROHS-Compliant 260-Pin BGA
675
C
16M x 18
GS82583ED18GK-625
SigmaQuad-IIIe B4
ROHS-Compliant 260-Pin BGA
625
C
16M x 18
GS82583ED18GK-550
SigmaQuad-IIIe B4
ROHS-Compliant 260-Pin BGA
550
C
16M x 18
GS82583ED18GK-500
SigmaQuad-IIIe B4
ROHS-Compliant 260-Pin BGA
500
C
16M x 18
GS82583ED18GK-675I
SigmaQuad-IIIe B4
ROHS-Compliant 260-Pin BGA
675
I
16M x 18
GS82583ED18GK-625I
SigmaQuad-IIIe B4
ROHS-Compliant 260-Pin BGA
625
I
16M x 18
GS82583ED18GK-550I
SigmaQuad-IIIe B4
ROHS-Compliant 260-Pin BGA
550
I
16M x 18
GS82583ED18GK-500I
SigmaQuad-IIIe B4
ROHS-Compliant 260-Pin BGA
500
I
8M x 36
GS82583ED36GK-675
SigmaQuad-IIIe B4
ROHS-Compliant 260-Pin BGA
675
C
8M x 36
GS82583ED36GK-625
SigmaQuad-IIIe B4
ROHS-Compliant 260-Pin BGA
625
C
8M x 36
GS82583ED36GK-550
SigmaQuad-IIIe B4
ROHS-Compliant 260-Pin BGA
550
C
8M x 36
GS82583ED36GK-500
SigmaQuad-IIIe B4
ROHS-Compliant 260-Pin BGA
500
C
8M x 36
GS82583ED36GK-675I
SigmaQuad-IIIe B4
ROHS-Compliant 260-Pin BGA
675
I
8M x 36
GS82583ED36GK-625I
SigmaQuad-IIIe B4
ROHS-Compliant 260-Pin BGA
625
I
8M x 36
GS82583ED36GK-550I
SigmaQuad-IIIe B4
ROHS-Compliant 260-Pin BGA
550
I
8M x 36
GS82583ED36GK-500I
SigmaQuad-IIIe B4
ROHS-Compliant 260-Pin BGA
500
I
Note: C = Commercial Temperature Range. I = Industrial Temperature Range.
Rev: 1.06 8/2017
25/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
GS82583ED18/36GK-675/625/550/500
Revision History
Rev. Code
Types of Changes
Format or Content
GS82583ED1836GK_r1_01
—
GS82583ED1836GK_r1_02
Content
• Removed leaded BGA package support.
GS82583ED1836GK_r1_03
Content
• Miscellaneous cleanup.
• Corrected write data input latency.
GS82583ED1836GK_r1_04
Content
• Changed VDD spec to 1.3V  50mV.
• Added package thermal impedances.
• Revised tCQHCQH specs.
GS82583ED1836GK_r1_05
Content
• Removed Preliminary banner.
• Added IDD specs.
GS82583ED1836GK_r1_06
Content
• Removed ECCRAM references.
Rev: 1.06 8/2017
Revisions
• Initial public release.
26/26
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2014, GSI Technology
Similar pages