TI1 ADS8860IDRCR 16-bit, 1-msps, serial interface, micropower, miniature single-ended input, sar analog-to-digital converter Datasheet

ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
16-Bit, 1-MSPS, Serial Interface, microPower, Miniature,
Single-Ended Input, SAR Analog-to-Digital Converter
Check for Samples: ADS8860
FEATURES
APPLICATIONS
• Sample Rate: 1 MHz
• No Latency Output
• Unipolar, Single-Ended Input Range:
0 to +VREF
• SPI™-Compatible Serial Interface with
Daisy-Chain Option
• Excellent AC and DC Performance:
– SNR: 93 dB, THD: –108 dB
– INL: ±1.0 LSB (typ), ±2.0 LSB (max)
– DNL: ±1.0 LSB (max), 16-Bit NMC
• Wide Operating Range:
– AVDD: 2.7 V to 3.6 V
– DVDD: 2.7 V to 3.6 V
(Independent of AVDD)
– REF: 2.5 V to 5 V (Independent of AVDD)
– Operating Temperature: –40°C to +85°C
• Low-Power Dissipation:
– 5.5 mW at 1 MSPS
– 0.55 mW at 100 kSPS
– 55 µW at 10 kSPS
• Power-Down Current (AVDD): 50 nA
• Full-Scale Step Settling to 16 Bits: 290 ns
• Packages: MSOP-10 and SON-10
•
•
•
•
1
234
2.5 V to 5 V
REF
Automatic Test Equipment (ATE)
Instrumentation and Process Controls
Precision Medical Equipment
Low-Power, Battery-Operated Instruments
DESCRIPTION
The ADS8860 is a 16-bit, 1-MSPS, single-ended
input, analog-to-digital converter (ADC). The device
operates with a 2.5-V to 5-V external reference,
offering a wide selection of signal ranges without
additional input signal scaling. The reference voltage
setting is independent of, and can exceed, the analog
supply voltage (AVDD).
The device
that also
cascading
indicator bit
easy.
offers an SPI-compatible serial interface
supports daisy-chain operation for
multiple devices. An optional busymakes synchronizing with the digital host
The device supports unipolar single-ended analog
inputs in the range of –0.1 V to VREF + 0.1 V.
Device operation is optimized for very low-power
operation. Power consumption directly scales with
speed. This feature makes the ADS8860 excellent for
lower-speed applications.
No separate LDO Required
for ADC supply
AVDD
2.7 V to 3.6 V
DVDD
0 V - VREF
DIN
AINP
ADS8860
AINM
SCLK
DOUT
Digital Host
CONVST
GND
1
2
3
4
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
TINA is a trademark of Texas Instruments Inc..
SPI is a trademark of Motorola Inc.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2013, Texas Instruments Incorporated
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
FAMILY INFORMATION (1)
(1)
(2)
THROUGHPUT
18-BIT, TRUE-DIFFERENTIAL
16-BIT, SINGLE-ENDED
16-BIT, TRUE-DIFFERENTIAL
100 kSPS
ADS8887
ADS8866
ADS8867
250 kSPS
—
—
—
400 kSPS
ADS8885
ADS8864
ADS8865
500 kSPS
—
ADS8319 (2)
ADS8318 (2)
680 kSPS
ADS8883
ADS8862
ADS8863
1 MSPS
ADS8881
ADS8860
ADS8861
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or visit the
device product folder at www.ti.com.
Pin-to-pin compatible device with AVDD = 5 V.
ABSOLUTE MAXIMUM RATINGS (1)
Over operating free-air temperature range, unless otherwise noted.
VALUE
MIN
MAX
AINP to GND or AINN to GND
–0.3
REF + 0.3
V
AVDD to GND or DVDD to GND
–0.3
4
V
REF to GND
–0.3
5.7
V
Digital input voltage to GND
–0.3
DVDD + 0.3
V
Digital output to GND
–0.3
DVDD + 0.3
V
Operating temperature range, TA
–40
+85
°C
Storage temperature range, Tstg
–65
+150
°C
(1)
UNIT
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under electrical characteristics is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
THERMAL INFORMATION
ADS8860
THERMAL METRIC
(1)
DGS
DRC
10 PINS
10 PINS
θJA
Junction-to-ambient thermal resistance
151.9
111.1
θJCtop
Junction-to-case (top) thermal resistance
45.4
46.4
θJB
Junction-to-board thermal resistance
72.2
45.9
ψJT
Junction-to-top characterization parameter
3.3
3.5
ψJB
Junction-to-board characterization parameter
70.9
45.5
θJCbot
Junction-to-case (bottom) thermal resistance
N/A
N/A
(1)
2
UNITS
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
ELECTRICAL CHARACTERISTICS
All minimum and maximum specifications are at TA = –40°C to +85°C, AVDD = 3 V, DVDD = 3 V, VREF = 5 V,
and fSAMPLE = 1 MSPS, unless otherwise noted.
Typical specifications are at TA = +25°C, AVDD = 3 V, and DVDD = 3 V.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
ANALOG INPUT
Full-scale input span (1)
Operating input range
CI
(1)
AINP – AINN
0
VREF
V
AINP
–0.1
VREF + 0.1
V
AINN
–0.1
+ 0.1
Input capacitance
AINP and AINN terminal to GND
Input leakage current
During acquisition for dc input
V
59
pF
5
nA
16
Bits
SYSTEM PERFORMANCE
Resolution
NMC
No missing codes
DNL
Differential linearity
INL
Integral linearity (3)
EO
Offset error
16
(4)
±0.6
1
LSB (2)
–2
±0.8
2
LSB (2)
±1
4
–4
Offset error drift with temperature
EG
Bits
–0.99
mV
±1.5
Gain error
–0.01
Gain error drift with temperature
±0.005
µV/°C
0.01
±0.15
CMRR
Common-mode rejection ratio
With common-mode input signal = 5 VPP at dc
PSRR
Power-supply rejection ratio
At mid-code
90
Transition noise
%FSR
ppm/°C
100
dB
80
dB
0.5
LSB
SAMPLING DYNAMICS
tconv
Conversion time
500
tACQ
Acquisition time
290
710
ns
Maximum throughput rate
with or without latency
(1)
(2)
(3)
(4)
ns
1000
kHz
Aperture delay
4
ns
Aperture jitter, RMS
5
ps
Step response
Settling to 16-bit accuracy
290
ns
Overvoltage recovery
Settling to 16-bit accuracy
290
ns
Ideal input span, does not include gain or offset error.
LSB = least significant bit.
This parameter is the endpoint INL, not best-fit.
Measured relative to actual measured reference.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
3
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
All minimum and maximum specifications are at TA = –40°C to +85°C, AVDD = 3 V, DVDD = 3 V, VREF = 5 V,
and fSAMPLE = 1 MSPS, unless otherwise noted.
Typical specifications are at TA = +25°C, AVDD = 3 V, and DVDD = 3 V.
PARAMETER
TEST CONDITIONS
MIN
TYP
90.5
MAX
UNIT
DYNAMIC CHARACTERISTICS
At 1 kHz, VREF = 5 V
SINAD
Signal-to-noise + distortion (5)
92.9
dB
At 10 kHz, VREF = 5 V
92.9
dB
At 100 kHz, VREF = 5 V
88.2
dB
93
dB
93
dB
At 100 kHz, VREF = 5 V
88.5
dB
At 1 kHz, VREF = 5 V
–108
dB
At 10 kHz, VREF = 5 V
–108
dB
At , VREF = 5 V
-101
dB
At 1 kHz, VREF = 5 V
108
dB
At 10 kHz, VREF = 5 V
108
dB
At 100 kHz, VREF = 5 V
101
dB
30
MHz
At 1 kHz, VREF = 5 V
Signal-to-noise ratio (5)
SNR
At 10 kHz, VREF = 5 V
Total harmonic distortion (5) (6)
THD
SFDR
BW–3dB
92
Spurious-free dynamic range (5)
–3-dB small-signal bandwidth
EXTERNAL REFERENCE INPUT
VREF
Input range
2.5
Reference input current
V
μA
250
nA
10
22
µF
Analog supply
2.7
3
3.6
V
Digital supply range for SCLK > 40 MHz
2.7
3
3.6
V
Digital supply range for SCLK < 40 MHz
1.65
1.8
3.6
V
1.8
2.4
mA
5.5
7.2
mW
Reference leakage current
CREF
5
300
During conversion, 1-MHz sample rate, mid-code
Decoupling capacitor at the REF
input
POWER-SUPPLY REQUIREMENTS
AVDD
Power-supply
voltage
Supply current
DVDD
AVDD
1-MHz sample rate, AVDD = 3 V
1-MHz sample rate, AVDD = 3 V
PVA
Power dissipation
100-kHz sample rate, AVDD = 3 V
10-kHz sample rate, AVDD = 3 V
IAPD
Device power-down current (7)
0.55
mW
55
μW
50
nA
DIGITAL INPUTS: LOGIC FAMILY (CMOS)
VIH
High-level input voltage
VIL
Low-level input voltage
ILK
Digital input leakage current
1.65 V < DVDD < 2.3 V
0.8 × DVDD
DVDD + 0.3
V
2.3 V < DVDD < 3.6 V
0.7 × DVDD
DVDD + 0.3
V
1.65 V < DVDD < 2.3 V
–0.3
0.2 × DVDD
V
2.3 V < DVDD < 3.6 V
–0.3
0.3 × DVDD
V
±100
nA
0.8 × DVDD
DVDD
V
0
0.2 × DVDD
V
–40
+85
°C
±10
DIGITAL OUTPUTS: LOGIC FAMILY (CMOS)
VOH
High-level output voltage
IO = 500-μA source, CLOAD = 20 pF
VOL
Low-level output voltage
IO = 500-μA sink, CLOAD = 20 pF
TEMPERATURE RANGE
TA
(5)
(6)
(7)
4
Operating free-air temperature
All specifications expressed in decibels (dB) refer to the full-scale input (FSR) and are tested with an input signal 0.5 dB below full-scale,
unless otherwise specified.
Calculated on the first nine harmonics of the input frequency.
The device automatically enters a power-down state at the end of every conversion, and remains in power-down during the acquisition
phase.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
TIMING CHARACTERISTICS
3-WIRE OPERATION
1/fsample
DIN = HIGH
tconv-max
tACQ
tclkh
th-CK-DO
CONVST
tclkl
tquiet
œœ
SCLK
1
2
td-CNV-DO
D15
DOUT
3
14
15
16
D1
D0
tSCLK
œœ
D14
D13
D2
œœ
twh-CNV-min
td-CK-DO
td-CK-DOhz
Figure 1. 3-Wire Operation: CONVST Functions as Chip Select
NOTE
Figure 1 shows the timing diagram for the 3-Wire CS Mode Without a Busy Indicator
interface option. However, the timing parameters specified in Table 1 are also applicable
for the 3-Wire CS Mode With a Busy Indicator interface option, unless otherwise specified.
Refer to the Digital Interface section for specific details for each interface option.
Table 1. TIMING REQUIREMENTS: 3-Wire Operation (1)
PARAMETER
MIN
TYP
MAX
UNIT
tACQ
Acquisition time
290
tconv
Conversion time
500
1/fsample
Time between conversions
twh-CNV
Pulse duration: CONVST high
fSCLK
SCLK frequency
tSCLK
SCLK period
tclkl
SCLK low time
tclkh
SCLK high time
th-CK-DO
SCLK falling edge to current data invalid
td-CK-DO
SCLK falling edge to next data valid delay
13.4
ns
td-CNV-DO
Enable time: CONVST low to MSB valid
12.3
ns
td-CNV-DOhz
Disable time: CONVST high or last SCLK falling edge to DOUT 3-state (CS mode)
13.2
ns
tquiet
Quiet time
(1)
ns
710
1000
ns
ns
10
ns
66.6
MHz
0.45
0.55
tSCLK
0.45
0.55
tSCLK
15
ns
3
ns
20
ns
All specifications are at TA = –40°C to +85°C, AVDD = 3 V, and DVDD = 3 V, unless otherwise noted.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
5
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
4-WIRE OPERATION
1/fsample
tACQ
tconv-max
CONVST
tsu-DI-CNV
twl-CNV
DIN
œœ
SCLK
1
DOUT
D15
2
3
D14
D13
14
15
16
D1
D0
œœ
twh-DI-min
td-DI-DO
D2
œœ
td-DI-DOhz
Figure 2. 4-Wire Operation: DIN Functions as Chip Select
NOTE
Figure 2 shows the timing diagram for the 4-Wire CS Mode Without a Busy Indicator
interface option. However, the timing parameters specified in Table 2 are also applicable
for the 4-Wire CS Mode With a Busy Indicator interface option, unless otherwise specified.
Refer to the Digital Interface section for specific details for each interface option.
Table 2. TIMING REQUIREMENTS: 4-Wire Operation (1)
PARAMETER
MIN
TYP
MAX
UNIT
tACQ
Acquisition time
290
tconv
Conversion time
500
1/fsample
Time between conversions
1000
ns
twh-DI
Pulse duration: DIN high
10
ns
twl-CNV
Pulse width: CONVST low
20
td-DI-DO
Delay time: DIN low to MSB valid
td-DI-DOhz
Delay time: DIN high or last SCLK falling edge to DOUT 3-state
tsu-DI-CNV
Setup time: DIN high to CONVST rising edge
th-DI-CNV
Hold time: DIN high from CONVST rising edge (see Figure 61)
(1)
6
ns
710
ns
ns
12.3
ns
13.2
ns
7.5
ns
0
ns
All specifications are at TA = –40°C to +85°C, AVDD = 3 V, and DVDD = 3 V, unless otherwise noted.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
DAISY-CHAIN OPERATION
1/fsample
tconv-
tACQ
max
CONVST
th-CK-CNV
SCLK
DIN 1 = LOW
1
2
15
16
17
18
31
32
D15
D14
D1
D0
tsu-DI-CK
tsu-CK-CNV
DOUT 1,
DIN 2
D15
D14
D1
D0
DOUT 2
D15
D15
D1
D0
Device 2 Data
Device 1 Data
Figure 3. Daisy-Chain Operation: Two Devices
NOTE
Figure 3 shows the timing diagram for the Daisy-Chain Mode Without a Busy Indicator
interface option. However, the timing parameters specified in Table 3 are also applicable
for the Daisy-Chain Mode With a Busy Indicator interface option, unless otherwise
specified. Refer to the Digital Interface section for specific details for each interface option.
Table 3. TIMING REQUIREMENTS: Daisy-Chain (1)
PARAMETER
MIN
tACQ
Acquisition time
290
tconv
Conversion time
500
1/fsample
Time between conversions
tsu-CK-CNV
Setup time: SCLK valid to CONVST rising edge
th-CK-CNV
Hold time: SCLK valid from CONVST rising edge
tsu-DI-CNV
Setup time: DIN low to CONVST rising edge (see )
th-DI-CNV
Hold time: DIN low from CONVST rising edge (see Figure 61)
tsu-DI-CK
Setup time: DIN valid to SCLK falling edge
(1)
TYP
MAX
UNIT
ns
710
ns
1000
ns
5
ns
5
ns
7.5
ns
0
ns
1.5
ns
All specifications are at TA = –40°C to +85°C, AVDD = 3 V, and DVDD = 3 V, unless otherwise noted.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
7
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
EQUIVALENT CIRCUITS
500 µA
IOL
1.4 V
DOUT
20 pF
500 µA
IOH
Figure 4. Load Circuit for Digital Interface Timing
DIN
CONVST
SCLK
VIH
VIL
VOH
VOH
VOL
VOL
SDO
Figure 5. Voltage Levels for Timing
8
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
PIN CONFIGURATIONS
DGS PACKAGE
VSSOP-10
(TOP VIEW, Not to Scale)
DRC PACKAGE
SON-10
(TOP VIEW, Not to Scale)
REF
1
10
DVDD
AVDD
2
9
DIN
AINP
3
8
SCLK
AINN
4
7
DOUT
GND
5
6
CONVST
REF
1
10
DVDD
AVDD
2
9
DIN
AINP
3
8
SCLK
AINN
4
7
DOUT
GND
5
6
CONVST
Thermal
PAD
PIN ASSIGNMENTS
PIN NAME
PIN
NUMBER
FUNCTION
AINN
4
Analog input
Inverting analog signal input
AINP
3
Analog input
Noninverting analog signal input
AVDD
2
Analog
CONVST
6
Digital input
Convert input.
This pin also functions as the CS input in 3-wire interface mode. Refer to the
Description and Timing Characteristics sections for more details.
Serial data input.
The DIN level at the start of a conversion selects the mode of operation (such as CS
or daisy-chain mode). This pin also serves as the CS input in 4-wire interface mode.
Refer to the Description and Timing Characteristics sections for more details.
DESCRIPTION
Analog power supply.
This pin must be decoupled to GND with a 1-μF capacitor.
DIN
9
Digital input
DOUT
7
Digital output
Serial data output
DVDD
10
Power supply
Digital interface power supply.
This pin must be decoupled to GND with a 1-μF capacitor.
Device ground.
Note that this pin is a common ground pin for both the analog power supply (AVDD)
and digital I/O supply (DVDD). The reference return line is also internally connected to
this pin.
GND
5
Analog, digital
REF
1
Analog
SCLK
8
Digital input
Clock input for serial interface.
Data output (on DOUT) are synchronized with this clock.
Thermal pad
—
Thermal pad
Exposed thermal pad.
Texas Instruments recommends connecting the thermal pad to the printed circuit
board (PCB) ground.
Positive reference input.
This pin must be decoupled with a 10-μF or larger capacitor.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
9
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
TYPICAL CHARACTERISTICS
At TA = +25°C, AVDD = 3 V, DVDD = 3 V, VREF = 5 V, and fSAMPLE = 1 MSPS, unless otherwise noted.
1
Typical Differential Nonlinearity (LSB)
Typical Integral Nonlinearity (LSB)
2
AVDD = 3 V
REF = 2.5 V
TA = 25ƒC
1.5
1
0.5
0
-0.5
-1
-1.5
AVDD = 3 V
REF = 2.5 V
TA = 25ƒC
0.75
0.5
0.25
0
-0.25
-0.5
-0.75
-2
-1
0
13107
26214
39321
52428
ADC Output Code
65535
0
13107
Figure 6. TYPICAL INL (VREF = 2.5 V)
Typical Differential Nonlinearity (LSB)
Typical Integral Nonlinearity (LSB)
65535
C002
1
AVDD = 3 V
REF = 5 V
TA = 25ƒC
1.5
1
0.5
0
-0.5
-1
-1.5
AVDD = 3 V
REF = 5 V
TA = 25ƒC
0.75
0.5
0.25
0
-0.25
-0.5
-0.75
-1
-2
0
13107
26214
39321
ADC Output Code
52428
0
65535
13107
26214
39321
52428
ADC Output Code
C003
Figure 8. TYPICAL INL (VREF = 5 V)
65535
C004
Figure 9. TYPICAL DNL (VREF = 5 V)
2
1
Differential Nonlinearity (LSB)
AVDD = 3 V
REF = 5 V
1.5
Integral Nonlinearity (LSB)
52428
Figure 7. TYPICAL DNL (VREF = 2.5 V)
2
1
0.5
0
-0.5
-1
-1.5
-2
AVDD = 3 V
REF = 5 V
0.75
0.5
0.25
0
-0.25
-0.5
-0.75
-1
-40
-15
10
35
60
Free-Air Temperature( oC)
85
-40
C00
Figure 10. INL vs TEMPERATURE
10
26214
39321
ADC Output Code
C001
Submit Documentation Feedback
-15
10
35
Free-Air Temperature (oC)
60
85
C00
Figure 11. DNL vs TEMPERATURE
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, AVDD = 3 V, DVDD = 3 V, VREF = 5 V, and fSAMPLE = 1 MSPS, unless otherwise noted.
2
1
Integral Nonlinearity (LSB)
1.5
Differential Nonlinearity (LSB)
AVDD = 3 V
TA = 25oC
1
0.5
0
-0.5
-1
-1.5
-2
AVDD = 3 V
TA = 25oC
0.75
0.5
0.25
0
-0.25
-0.5
-0.75
-1
2.5
3
3.5
4
Reference Voltage (V)
4.5
5
2.5
Figure 12. INL vs REFERENCE VOLTAGE
4.5
5
C00
100
AVDD = 3 V
REF = 2.5 V
TA = 25oC
AVDD = 3 V
REF = 5 V
TA = 25oC
80
Hits per Code (%)
50
Hits per Code (%)
3.5
4
Reference Voltage (V)
Figure 13. DNL vs REFERENCE VOLTAGE
60
40
30
20
60
40
20
10
0
32735
32736
32737
32738
32739
32740
0
32741
ADC Output Code
32750
32751
C00
Figure 14. DC INPUT HISTOGRAM (VREF = 2.5 V)
32752
32753
ADC Output Code
32754
C01
Figure 15. DC INPUT HISTOGRAM (VREF = 5 V)
0
0
AVDD = 3 V
REF = 2.5 V
TA = 25ƒC
fIN = 1 kHz
SNR = 88.7 dB
THD = ±111 dB
±40
±60
±80
AVDD = 3 V
REF = 5 V
TA = 25ƒC
fIN = 1 kHz
SNR = 93 dB
THD = ±108 dB
±20
±40
±60
Power (dB)
±20
Power (dB)
3
C00
±100
±120
±80
±100
±120
±140
±140
±160
±160
±180
±180
±200
±200
0
100
200
300
400
Input Frequency (kHz)
500
0
C001
Figure 16. TYPICAL FFT (VREF = 2.5 V)
100
200
300
Input Frequency (kHz)
400
Product Folder Links: ADS8860
C002
Figure 17. TYPICAL FFT (VREF = 5 V)
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
500
11
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, AVDD = 3 V, DVDD = 3 V, VREF = 5 V, and fSAMPLE = 1 MSPS, unless otherwise noted.
95
Signal-to-Noise and Distortion (dBFS)
Signal-to-Noise Ratio (dBFS)
95
94
93
92
91
90
89
88
fIN = 1 kHz
94
93
92
91
90
89
88
fIN = 1 kHz
87
87
2.5
3
3.5
4
Reference Voltage (V)
4.5
2.5
5
Figure 18. SNR vs REFERENCE VOLTAGE
Total Harmonic Distortion (dBFS)
Effective Number of Bits
4.5
5
C01
-105
fIN = 1 kHz
15.5
15
14.5
fIN = 1 kHz
-107
-109
-111
-113
-115
14
2.5
3
3.5
4
Reference Voltage (V)
4.5
2.5
5
3
C01
Figure 20. ENOB vs REFERENCE VOLTAGE
3.5
4
Reference Voltage (V)
4.5
5
C01
Figure 21. THD vs REFERENCE VOLTAGE
115
96
fIN = 1 kHz
fIN = 1 kHz
Signal-to-Noise Ratio (dBFS)
Spurious-Free Dynamic Range (dBFS)
3.5
4
Reference Voltage (V)
Figure 19. SINAD vs REFERENCE VOLTAGE
16
113
111
109
107
105
95
94
93
92
91
90
2.5
3
3.5
4
Reference Voltage (V)
4.5
5
-40
C01
Figure 22. SFDR vs REFERENCE VOLTAGE
12
3
C01
Submit Documentation Feedback
-15
10
35
60
Free-Air Temperature (oC)
85
C01
Figure 23. SNR vs TEMPERATURE
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, AVDD = 3 V, DVDD = 3 V, VREF = 5 V, and fSAMPLE = 1 MSPS, unless otherwise noted.
16
fIN = 1 kHz
95
Effective Number of Bits
Signal-to-Noise and Distortion (dBFS)
96
94
93
92
15
14
13
91
fIN = 1 kHz
90
12
-40
-15
10
35
Free-Air Temperature (oC)
60
85
-40
Figure 24. SINAD vs TEMPERATURE
Spurious-Free Dynamic Reange (dBFS)
Total Harmonic Distortion (dBFS)
fIN = 1 kHz
-103
-106
-109
-112
-115
-15
10
35
Free-Air Temperature (oC)
60
60
85
C02
115
fIN = 1 kHz
112
109
106
103
100
85
-40
-15
C02
Figure 26. THD vs TEMPERATURE
10
35
60
Free-Air Temperfature (oC)
85
C02
Figure 27. SFDR vs TEMPERATURE
97
Signal-to-Noise and Distortion (dB FS)
97
Signal-to-Noise Ratio (dBFS)
10
35
Free-Air Temperature (oC)
Figure 25. ENOB vs TEMPERATURE
-100
-40
-15
C01
95
93
91
89
87
85
95
93
91
89
87
85
0
20
40
60
Input Frequency (kHz)
80
100
0
C02
Figure 28. SNR vs INPUT FREQUENCY
20
40
60
Input Frequency (kHz)
80
Product Folder Links: ADS8860
C02
Figure 29. SINAD vs INPUT FREQUENCY
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
100
13
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, AVDD = 3 V, DVDD = 3 V, VREF = 5 V, and fSAMPLE = 1 MSPS, unless otherwise noted.
-90
Total Harmonic Distortion (dBFS)
Effective Number of Bits
16
15
14
13
12
-95
-100
-105
-110
-115
0
20
40
60
Input Frequency (kHz)
80
100
0
40
60
Input Frequency (kHz)
80
100
C02
Figure 31. THD vs INPUT FREQUENCY
2.4
115
2.3
Analog Supply Current (mA)
Spurious-Free Dynamic Range (dBFS)
Figure 30. ENOB vs INPUT FREQUENCY
110
105
100
95
2.2
2.1
2
1.9
1.8
1.7
1.6
90
0
20
40
60
Input Frequency (kHz)
80
-40
100
10
35
Free-Air Temperature (oC)
60
85
C02
Figure 33. SUPPLY CURRENT vs TEMPERATURE
6
2
5.9
1.8
Analog Supply Current (mA)
Power Consumption (mW)
-15
C02
Figure 32. SFDR vs INPUT FREQUENCY
5.8
5.7
5.6
5.5
5.4
5.3
5.2
5.1
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
5
-40
-15
10
35
Free-Air Temperature (oC)
60
85
0
0
200
C02
Figure 34. POWER CONSUMPTION vs TEMPERATURE
14
20
C02
400
600
Throughput (kSPS)
800
1000
C03
Figure 35. SUPPLY CURRENT vs THROUGHPUT
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, AVDD = 3 V, DVDD = 3 V, VREF = 5 V, and fSAMPLE = 1 MSPS, unless otherwise noted.
200
175
5
Power-Down Current (mA)
Power Consumption (mW)
6
4
3
2
1
125
100
75
50
25
0
0
0
200
400
600
Throughput (kSPS)
800
-40
1000
60
85
C03
0.0100
AVDD = 3 V
REF = 5 V
3
AVDD = 3 V
REF = 5 V
0.0075
0.0050
Gain-Error (%FS)
2
1
0
-1
-2
0.0025
0.0000
-0.0025
-0.0050
-0.0075
-3
-0.0100
-4
-40
-15
10
35
60
Free-Air Temperature (oC)
-40
85
-15
10
35
60
Free-Air Temperature (oC)
C03
Figure 38. OFFSET vs TEMPERATURE
85
C03
Figure 39. GAIN ERROR vs TEMPERATURE
2000
5000
AVDD = 3 V
REF = 2.5 V
TA = 25oC
6000 Devices
AVDD = 3 V
REF = 2.5 V
TA = 25oC
6000 Devices
1600
Frequency
Frequency
10
35
Free-Air Temperature (oC)
Figure 37. POWER-DOWN CURRENT vs TEMPERATURE
4
4000
-15
C03
Figure 36. POWER CONSUMPTION vs THROUGHPUT
Offset (mV)
150
3000
2000
1200
800
400
1000
0
0
-0.01
-0.005
0
0.005
Gain Error (% FS)
-4
0.01
Figure 40. TYPICAL DISTRIBUTION OF GAIN ERROR
-3
-2
-1
0
1
2
3
Offset (mV)
C00
4
C00
Figure 41. TYPICAL DISTRIBUTION OF OFFSET ERROR
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
15
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, AVDD = 3 V, DVDD = 3 V, VREF = 5 V, and fSAMPLE = 1 MSPS, unless otherwise noted.
4000
6000
AVDD = 3 V
REF = 2.5 V
TA = 25oC
6000 Devices
5000
AVDD = 3 V
REF = 2.5 V
TA = 25oC
6000 Devices
3000
Frequency
Frequency
4000
3000
2000
2000
1000
1000
0
0
-1
-0.5
0
0.5
Differential Nonlinearity Min and Max (LSB)
1
-2
C009
Figure 42. TYPICAL DISTRIBUTION OF DIFFERENTIAL
NONLINEARITY (Minimum and Maximum)
16
-1
0
1
Integral Nonlinearity Min and Max (LSB)
2
C010
Figure 43. TYPICAL DISTRIBUTION OF INTEGRAL
NONLINEARITY (Minimum and Maximum)
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
OVERVIEW
The ADS8860 is a high-speed, successive approximation register (SAR), analog-to-digital converter (ADC) from
a 16- and 18-bit product family. This compact device features high performance. Power consumption is
inherently low and scales linearly with sampling speed. The architecture is based on charge redistribution, which
inherently includes a sample-and-hold (S/H) function.
The ADS8860 supports a pseudo-differential analog input across two pins (INP and INN). When a conversion is
initiated, the differential input on these pins is sampled on the internal capacitor array. While a conversion is in
progress, both the INP and INN inputs are disconnected from the internal circuit.
The ADS8860 uses an internal clock to perform conversions. The device reconnects the sampling capacitors to
the INP and INN pins after conversion and then enters an acquisition phase. During the acquisition phase, the
device is powered down and the conversion result can be read.
The device digital output is available in SPI-compatible format, which makes interfacing with microprocessors,
digital signal processors (DSPs), or field-programmable gate arrays (FPGAs) easy.
ANALOG INPUT
As shown in Figure 44, the device features a pseudo-differential analog input. AINP can swing from GND – 0.1 V
to VREF + 0.1 V and AINN can swing from GND – 0.1 V to GND + 0.1 V. Both positive and negative inputs are
individually sampled on 55-pF sampling capacitors and the device converts for the voltage difference between
the two sampled values: VINP – VINN. The pseudo-differential signal range is 0 V to +VREF.
AVDD
REF
DVDD
REF
CONVST
AINP
Sample
and
Hold
AINN
SCLK
SAR
ADC
ADC
SPI
DOUT
DIN
AGND
REFM
DGND
GND
GND
Figure 44. Detailed Block Diagram
Figure 45 shows an equivalent circuit of the input sampling stage. The sampling switch is represented by a 96-Ω
resistance in series with the ideal switch. Refer to the ADC Input Driver section for more details on the
recommended driving circuits.
Device in Hold Mode
96
AINP
4 pF
55 pF
REF
4 pF
55 pF
96
GND
GND
AINN
Figure 45. Input Sampling Stage Equivalent Circuit
Figure 44 and Figure 45 illustrate electrostatic discharge (ESD) protection diodes to REF and GND from both
analog inputs. Make sure that these diodes do not turn on by keeping the analog inputs within the specified
range.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
17
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
REFERENCE
The device operates with an external reference voltage and switches binary-weighted capacitors onto the
reference terminal (REF pin) during the conversion process. The switching frequency is proportional to the
internal conversion clock frequency but the dynamic charge requirements are a function of the absolute value of
the input voltage and reference voltage. This dynamic load must be supported by a reference driver circuit
without degrading the noise and linearity performance of the device. During the acquisition process, the device
automatically powers down and does not take any dynamic current from the external reference source. The basic
circuit diagram for such a reference driver circuit for precision ADCs is shown in Figure 46. Refer to the ADC
Reference Driver section for more details on the application circuits.
RREF_FLT
Buffer
CREF_FLT
RBUF_FLT
Voltage
Reference
REF
CBUF_FLT
ADC
Figure 46. Reference Driver Schematic
CLOCK
The device uses an internal clock for conversion. Conversion duration may vary but is bounded by the minimum
and maximum value of tconv, as specified in the Timing Characteristics section. An external SCLK is only used for
a serial data read operation. Data are read after a conversion completes and when the device is in acquisition
phase for the next sample.
18
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
ADC TRANSFER FUNCTION
The ADS8860 is a unipolar, single-ended input device. The device output is in straight binary format.
Figure 47 shows ideal characteristics for the device. The full-scale range for the ADC input (AINP – AINN) is
equal to the reference input voltage to the ADC (VREF). 1 LSB is equal to [(VREF / 216)].
ADC Code (Hex)
FFFF
8000
7FFF
0001
0000
VIN
1 LSB
VREF/2
VREF
Single-Ended Analog Input
(AINP ± AINN)
Figure 47. Single-Ended Transfer Characteristics
DIGITAL INTERFACE
The ADS8860 is a low pin-count device. However, the device offers six different options for interfacing with the
digital host.
These options can be broadly classified as being either CS mode (in either a 3- or 4-wire interface) or daisychain mode. The device operates in CS mode if DIN is high at the CONVST rising edge. If DIN is low at the
CONVST rising edge, or if DIN and CONVST are connected together, the device operates in daisy-chain mode.
In both modes, the device can either operate with or without a busy indicator, where the busy indicator is a bit
preceding the output data bits that can be used to interrupt the digital host and trigger the data transfer.
The 3-wire interface in CS mode is useful for applications that need galvanic isolation on-board. The 4-wire
interface in CS mode allows the user to sample the analog input independent of the serial interface timing and,
therefore, allows easier control of an individual device while having multiple, similar devices on-board. The daisychain mode is provided to hook multiple devices in a chain similar to a shift register and is useful in reducing
component count and the number of signal traces on the board.
CS Mode
CS mode is selected if DIN is high at the CONVST rising edge. There are four different interface options
available in this mode: 3-wire CS mode without a busy indicator, 3-wire CS mode with a busy indicator, 4-wire
CS mode without a busy indicator, and 4-wire CS mode with a busy indicator. The following sections discuss
these interface options in detail.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
19
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
3-Wire CS Mode Without a Busy Indicator
This interface option is most useful when a single ADC is connected to an SPI-compatible digital host. In this
interface option, DIN can be connected to DVDD and CONVST functions as CS (as shown in Figure 48). As
shown in Figure 49, a CONVST rising edge forces DOUT to 3-state, samples the input signal, and causes the
device to enter a conversion phase. Conversion is done with the internal clock and continues regardless of the
state of CONVST. As a result, CONVST (functioning as CS) can be pulled low after the start of the conversion to
select other devices on the board. However, CONVST must return high before the minimum conversion time
(tconv-min) elapses and is held high until the maximum possible conversion time (tconv-max) elapses. A high level on
CONVST at the end of the conversion ensures the device does not generate a busy indicator.
DVDD
DIN
CONVST
CNV
SCLK
CLK
DOUT
SDI
ADC
Digital Host
Figure 48. Connection Diagram: 3-Wire CS Mode Without a Busy Indicator (DIN = 1)
1/fsample
DIN = HIGH
CONVST = 1
CONVST
SCLK
1
DOUT
D15
2
3
D14
D13
œœ
14
15
16
D1
D0
œœ
tACQ
tconv-max
tconv-min
ADC
STATE
D2
œœ
Acquiring
Sample N
Conversion Result of Sample N Clocked-out
while Acquiring Sample N+1
Converting
Sample N
End-of-Conversion
Figure 49. Interface Timing Diagram: 3-Wire CS Mode Without a Busy Indicator (DIN = 1)
When conversion is complete, the device enters an acquisition phase and powers down. CONVST (functioning
as CS) can be brought low after the maximum conversion time (tconv-max) elapses. On the CONVST falling edge,
DOUT comes out of 3-state and the device outputs the MSB of the data. The lower data bits are output on
subsequent SCLK falling edges. Data are valid on both SCLK edges. Data are valid on both edges of SCLK and
can be captured on either edge. However, a digital host capturing data on the SCLK falling edge can achieve a
faster reading rate (provided th_CK_DO is acceptable). DOUT goes to 3-state after the 16th SCLK falling edge or
when CONVST goes high, whichever occurs first.
20
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
3-Wire CS Mode With a Busy Indicator
This interface option is most useful when a single ADC is connected to an SPI-compatible digital host and an
interrupt-driven data transfer is desired. In this interface option, DIN can be connected to DVDD and CONVST
functions as CS (as shown in Figure 50). The pull-up resistor on the DOUT pin ensures that the IRQ pin of the
digital host is held high when DOUT goes to 3-state. As shown in Figure 51, a CONVST rising edge forces
DOUT to 3-state, samples the input signal, and causes the device to enter a conversion phase. Conversion is
done with the internal clock and continues regardless of the state of CONVST. As a result, CONVST (functioning
as CS) can be pulled low after the start of the conversion to select other devices on the board. However,
CONVST must be pulled low before the minimum conversion time (tconv-min) elapses and must remain low until
the maximum possible conversion time (tconv-max) elapses. A low level on the CONVST input at the end of a
conversion ensures the device generates a busy indicator.
DVDD
CNV
CONVST
CLK
SCLK
DIN
DVDD
DOUT
SDI
ADC
IRQ
Digital Host
Figure 50. Connection Diagram: 3-Wire CS Mode With a Busy Indicator
1/fsample
DIN = DVDD
CONVST
CONVST = 0
SCLK
1
2
3
D15
D14
œœ
15
16
17
D1
D0
œœ
SDO Pulled-up
DOUT
BUSY
D2
œœ
tACQ
tconv-max
tconv-min
ADC
STATE
Acquiring
Sample N
Conversion Result of Sample N Clocked-out
while Acquiring Sample N+1
Converting
Sample N
End-of-Conversion
Figure 51. Interface Timing Diagram: 3-Wire CS Mode With a Busy Indicator (DIN = 1)
When conversion is complete, the device enters an acquisition phase and powers down, DOUT comes out of 3state, and the device outputs a busy indicator bit (low level) on the DOUT pin. This configuration provides a highto-low transition on the IRQ pin of the digital host. The data bits are clocked out, MSB first, on the subsequent
SCLK falling edges. Data are valid on both SCLK edges. Data are valid on both edges of SCLK and can be
captured on either edge. However, a digital host capturing data on the SCLK falling edge can achieve a faster
reading rate (provided th_CK_DO is acceptable). DOUT goes to 3-state after the 17th SCLK falling edge or when
CONVST goes high, whichever occurs first.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
21
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
4-Wire CS Mode Without a Busy Indicator
This interface option is useful when one or more ADCs are connected to an SPI-compatible digital host.
Figure 52 shows the connection diagram for single ADC, Figure 54 shows the connection diagram for two ADCs.
CS
CNV
DIN
CONVST
DOUT
SDI
SCLK
CLK
ADC
Digital Host
Figure 52. Connection Diagram: Single ADC with 4-Wire CS Mode Without a Busy Indicator
In this interface option, DIN is controlled by the digital host and functions as CS. As shown in Figure 53, with DIN
high, a CONVST rising edge selects CS mode, forces DOUT to 3-state, samples the input signal, and causes the
device to enter a conversion phase. In this interface option, CONVST must be held at a high level from the start
of the conversion until all data bits are read. Conversion is done with the internal clock and continues regardless
of the state of DIN. As a result, DIN (functioning as CS) can be pulled low to select other devices on the board.
However, DIN must be pulled high before the minimum conversion time (tconv-min) elapses and remains high until
the maximum possible conversion time (tconv-max) elapses. A high level on DIN at the end of the conversion
ensures the device does not generate a busy indicator.
1/fsample
tconv-max
tACQ
tconv-min
CONVST
DIN = 1
DIN
SCLK
1
2
DOUT
D15
D14
œœ
15
16
œœ
ADC
STATE
End-ofConversion
Acquiring
Sample N
D1
D0
œœ
Read Sample N
Converting
Sample N
Acquiring Sample N+1
Figure 53. Interface Timing Diagram: Single ADC with 4-Wire CS Mode Without a Busy Indicator
22
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
When conversion is complete, the device enters acquisition phase and powers down. DIN (functioning as CS)
can be brought low after the maximum conversion time (tconv-max) elapses. On the DIN falling edge, DOUT comes
out of 3-state and the device outputs the MSB of the data. The lower data bits are output on subsequent SCLK
falling edges. Data are valid on both SCLK edges. Data are valid on both edges of SCLK and can be captured
on either edge. However, a digital host capturing data on the SCLK falling edge can achieve a faster reading rate
(provided th_CK_DO is acceptable). DOUT goes to 3-state after the 16th SCLK falling edge or when DIN goes high,
whichever occurs first.
As shown in Figure 54, multiple devices can be hooked together on the same data bus. In this case, as shown in
Figure 55, the DIN of the second device (functioning as CS for the second device) can go low after the first
device data are read and the DOUT of the first device is in 3-state.
Care must be taken so that CONVST and DIN are not both low together at any time during the cycle.
CS1
CS2
CNV
CONVST
DIN
CONVST
DIN
DOUT
DOUT
SCLK
SDI
SCLK
CLK
ADC #1
ADC #2
Digital Host
Figure 54. Connection Diagram: Two ADCs with 4-Wire CS Mode Without a Busy Indicator
1/fsample
tconv-max
tACQ
tconv-min
CONVST
DIN = 1
DIN
(ADC 1)
DIN = 1
DIN
(ADC 2)
SCLK
1
2
DOUT
D15
D14
œœ
15
16
17
18
D0
D15
D14
ADC
STATE
Acquiring
Sample N
Converting
Sample N
32
œœ
œœ
End-ofConversion
œœ
31
D1
D1
D0
œœ
œœ
Read Sample N
ADC 1
Read Sample N
ADC 2
Acquiring Sample N+1
Figure 55. Interface Timing Diagram: Two ADCs with 4-Wire CS Mode Without a Busy Indicator
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
23
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
4-Wire CS Mode With a Busy Indicator
This interface option is most useful when a single ADC is connected to an SPI-compatible digital host and an
interrupt-driven data transfer is desired. In this interface option, the analog sample is least affected by clock jitter
because the CONVST signal (used to sample the input) is independent of the data read operation. In this
interface option, DIN is controlled by the digital host and functions as CS (as shown in Figure 56). The pull-up
resistor on the DOUT pin ensures that the IRQ pin of the digital host is held high when DOUT goes to 3-state. As
shown in Figure 57, when DIN is high, a CONVST rising edge selects CS mode, forces DOUT to 3-state,
samples the input signal, and causes the device to enter a conversion phase. In this interface option, CONVST
must be held high from the start of the conversion until all data bits are read. Conversion is done with the internal
clock and continues regardless of the state of DIN. As a result, DIN (acting as CS) can be pulled low to select
other devices on the board. However, DIN must be pulled low before the minimum conversion time (tconv-min)
elapses and remains low until the maximum possible conversion time (tconv-max) elapses. A low level on the DIN
input at the end of a conversion ensures the device generates a busy indicator.
CS
DIN
CNV
CONVST
CLK
SCLK
DVDD
DOUT
SDI
IRQ
ADC
Digital Host
Figure 56. Connection Diagram: 4-Wire CS Mode With a Busy Indicator
1/fsample
tACQ
tconv-max
tconv-min
CONVST
DIN =0
DIN
SCLK
1
2
3
D15
D14
œœ
15
16
17
D1
D0
œœ
DOUT
ADC
STATE
SDO Pulled-up
Acquiring
Sample N
Converting
Sample N
BUSY
D2
œœ
Conversion Result of Sample N Clocked-out
while Acquiring Sample N+1
Figure 57. Interface Timing Diagram: 4-Wire CS Mode With a Busy Indicator
When conversion is complete, the device enters an acquisition phase and powers down, DOUT comes out of 3state, and the device outputs a busy indicator bit (low level) on the DOUT pin. This configuration provides a highto-low transition on the IRQ pin of the digital host. The data bits are clocked out, MSB first, on the subsequent
SCLK falling edges. Data are valid on both SCLK edges. Data are valid on both edges of SCLK and can be
captured on either edge. However, a digital host capturing data on the SCLK falling edge can achieve a faster
reading rate (provided th_CK_DO is acceptable). DOUT goes to 3-state after the 17th SCLK falling edge or when
DIN goes high, whichever occurs first. Care must be taken so that CONVST and DIN are not both low together at
any time during the cycle.
24
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
DAISY-CHAIN MODE
Daisy-chain mode is selected if DIN is low at the time of a CONVST rising edge or if DIN and CONVST are
connected together. Similar to CS mode, this mode features operation with or without a busy indicator. The
following sections discuss these interface modes in detail.
Daisy-Chain Mode Without a Busy Indicator
This interface option is most useful in applications where multiple ADC devices are used but the digital host has
limited interfacing capability. Figure 58 shows a connection diagram with N ADCs connected in the daisy-chain.
The CONVST pins of all ADCs in the chain are connected together and are controlled by a single pin of the
digital host. Similarly, the SCLK pins of all ADCs in the chain are connected together and are controlled by a
single pin of the digital host. The DIN pin for ADC 1 is connected to GND. The DOUT pin of ADC 1 is connected
to the DIN pin of ADC 2, and so on. The DOUT pin of the last ADC in the chain (ADC N) is connected to the SDI
pin of the digital host.
CNV
CONVST
DIN
DOUT
SCLK
CONVST
DIN
CONVST
DOUT
}
DIN
SCLK
CONVST
DOUT
DIN
SCLK
SDI
DOUT
SCLK
CLK
ADC 1
ADC 2
}
ADC N
ADC N1
Digital Host
Figure 58. Connection Diagram: Daisy-Chain Mode Without a Busy Indicator (DIN = 0)
As shown in Figure 59, the device DOUT pin is driven low when DIN and CONVST are low together. With DIN
low, a CONVST rising edge selects daisy-chain mode, samples the analog input, and causes the device to enter
a conversion phase. In this interface option, CONVST must remain high from the start of the conversion until all
data bits are read. When started, the conversion continues regardless of the state of SCLK, however SCLK must
be low at the CONVST rising edge so that the device does not generate a busy indicator at the end of the
conversion.
tconv-min
1/fsample
tconv-max
tACQ
CONVST
SCLK
1
2
œœ
15
16
17
18
D15
D14
œœ
31
32
DIN 1 = LOW
œœ
DOUT 1
DIN 2
D15
D14
D1
D0
D1
D0
œœ
œœ
D15
DOUT 2
œœ
œœ
End-ofConversion
ADC
STATE
D14
Acquiring
Sample N
Converting
Sample N
D1
D0
œœ
Read Sample N
ADC 2
Read Sample N
ADC 1
Acquiring Sample N+1
Figure 59. Interface Timing Diagram: For Two Devices in Daisy-Chain Mode Without a Busy Indicator
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
25
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
At the end of conversion, every ADC in the chain loads its own conversion result into the internal, 16-bit, shift
register and also outputs the MSB bit of this conversion result on its own DOUT pin. All ADCs enter an
acquisition phase and power-down. On every subsequent SCLK falling edge, the internal shift register of each
ADC latches the data available on its DIN pin and shifts out the next bit of data on its DOUT pin. Therefore, the
digital host receives the data of ADC N, followed by the data of ADC N–1, and so on (in MSB-first fashion). A
total of 16 x N SCLK falling edges are required to capture the outputs of all N devices in the chain. Data are valid
on both SCLK edges. Data are valid on both edges of SCLK and can be captured on either edge. However, a
digital host capturing data on the SCLK falling edge can achieve a faster reading rate (provided th_CK_DO is
acceptable).
Daisy-Chain Mode With a Busy Indicator
This interface option is most useful in applications where multiple ADC devices are used but the digital host has
limited interfacing capability and an interrupt-driven data transfer is desired. Figure 60 shows a connection
diagram with N ADCs connected in the daisy-chain. The CONVST pins of all ADCs in the chain are connected
together and are controlled by a single pin of the digital host. Similarly, the SCLK pins of all ADCs in the chain
are connected together and are controlled by a single pin of the digital host. The DIN pin for ADC 1 is connected
to its CONVST. The DOUT pin of ADC 1 is connected to the DIN pin of ADC 2, and so on. The DOUT pin of the
last ADC in the chain (ADC N) is connected to the SDI and IRQ pins of the digital host.
CNV
CONVST
DIN
DOUT
CONVST
DIN
DOUT
SCLK
SCLK
ADC 1
ADC 2
CONVST
}
DIN
DOUT
CONVST
DIN
DOUT
SCLK
SCLK
ADC N1
ADC N
IRQ
SDI
CLK
}
Digital Host
Figure 60. Connection Diagram: Daisy-Chain Mode With a Busy Indicator (DIN = 0)
26
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
As shown in Figure 61, the device DOUT pin is driven low when DIN and CONVST are low together. A CONVST
rising edge selects daisy-chain mode, samples the analog input, and causes the device to enter a conversion
phase. In this interface option, CONVST must remain high from the start of the conversion until all data bits are
read. When started, the conversion continues regardless of the state of SCLK, however SCLK must be high at
the CONVST rising edge so that the device generates a busy indicator at the end of the conversion.
tconv-min
1/fsample
tconv-max
tACQ
CONVST
SCLK
2
1
th-DI-CNV
œœ
16
17
18
19
D15
D14
œœ
32
33
DIN 1 =
CONVST
œœ
DOUT 1
DIN 2
BUSY
D15
D1
D0
D1
D0
œœ
œœ
BUSY
DOUT 2
œœ
œœ
End-ofConversion
ADC
STATE
D15
Acquiring
Sample N
Read Sample N
ADC 2
Converting
Sample N
D1
D0
œœ
Read Sample N
ADC 1
Acquiring Sample N+1
Figure 61. Interface Timing Diagram: For Two Devices in Daisy-Chain Mode With a Busy Indicator
At the end of conversion, every ADC in the chain loads its own conversion result into the internal, 16-bit, shift
register and also forces its DOUT pin high, thereby providing a low-to-high transition on the IRQ pin of the digital
host. All ADCs enter an acquisition phase and power-down. On every subsequent SCLK falling edge, the internal
shift register of each ADC latches the data available on its DIN pin and shifts out the next bit of data on its DOUT
pin. Therefore, the digital host receives the interrupt signal followed by the data of ADC N followed by the data of
ADC N–1, and so on (in MSB-first fashion). A total of (16 x N) + 1 SCLK falling edges are required to capture the
outputs of all N devices in the chain. Data are valid on both edges of SCLK and can be captured on either edge.
However, a digital host capturing data on the SCLK falling edge can achieve a faster reading rate (provided
th_CK_DO is acceptable). Note that the busy indicator bits of ADC 1 to ADC N–1 do not propagate to the next
device in the chain.
POWER SUPPLY
The device has two separate power supplies: AVDD and DVDD. The internal circuits of the device operate on
AVDD; DVDD is used for the digital interface. AVDD and DVDD can be independently set to any value within the
permissible range.
Decouple the AVDD and DVDD pins with GND, using individual 1-µF decoupling capacitors placed in close
proximity to the pin, as shown in Figure 62.
Digital
Supply
REF
Analog
Supply
AVDD
1 µF
DVDD
DIN
AINP
SCLK
AINN
DOUT
GND
CONVST
1 µF
Figure 62. Supply Decoupling
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
27
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
POWER SAVING
The device has an auto power-down feature that powers down the internal circuitry at the end of every
conversion. Referring to Figure 63, the input signal is acquired on the sampling capacitors when the device is in
a power-down state (tacq); at the same time, the result for the previous conversion is available for reading. The
device powers up on the start of the next conversion. During conversion phase (tconv), the device also consumes
current from the reference source (connected to pin REF).
tTHROUGHPUT
Device Phase
tCONV
tACQ
œœ
IREF
tACQ
~50000X
~50000X
œœ
IAVDD
tCONV
2 * tTHROUGHPUT
~1200X
~1200X
~2X
IAVG(AVDD+REF)
Figure 63. Power Scaling with Throughput
The conversion time, tconv, is independent of the SCLK frequency. When operating the device at speeds lower
than the maximum rated throughput, the conversion time, tconv, does not change; the device spends more time in
power-down state. Therefore, as shown in Figure 64, the device power consumption from the AVDD supply and
the external reference source is directly proportional to the speed of operation. Extremely low AVDD power-down
current (50 nA, typical) and extremely low external reference leakage current (250 nA, typical), make this device
ideal for very low throughput applications (such as pulsed measurements).
Power Consumption (mW)
6
5
4
3
2
1
0
0
200
400
600
Throughput (kSPS)
800
1000
C03
Figure 64. Power Scaling with Throughput
28
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
APPLICATION INFORMATION
The two primary circuits required to maximize the performance of a high-precision, successive approximation
register (SAR), analog-to-digital converter (ADC) are the input driver and the reference driver circuits. This
section details some general principles for designing these circuits, followed by some application circuits
designed using the ADS8860.
ADC REFERENCE DRIVER
The external reference source to the device must provide low-drift and very accurate voltage for the ADC
reference input and support the dynamic charge requirements without affecting the noise and linearity
performance of the device. The output broadband noise of most references can be in the order of a few 100
μVRMS. Therefore, in order to prevent any degradation in the noise performance of the ADC, the output of the
voltage reference must be appropriately filtered by using a low-pass filter with a cutoff frequency of a few
hundred Hertz.
After band-limiting the noise of the reference circuit, the next important step is to design a reference buffer that
can drive the dynamic load posed by the reference input of the ADC. The reference buffer must regulate the
voltage at the reference pin such that the value of VREF stays within the 1-LSB error at the start of each
conversion. This condition necessitates the use of a large capacitor, CBUF_FLT (refer to Figure 46) for regulating
the voltage at the reference input of the ADC. The amplifier selected to drive the reference pin should have an
extremely low offset and temperature drift with a low output impedance to drive the capacitor at the ADC
reference pin without any stability issues.
Reference Driver Circuit for VREF = 4 V
The application circuit in Figure 65 shows the schematic of a complete reference driver circuit that generates a
voltage of 4 V dc using a single 5-V supply. This circuit is suitable to drive the reference of the ADS8860 at
higher sampling rates up to 1 MSPS. The reference voltage of 4 V in this design is generated by the highprecision, low-noise REF3240 circuit. The output broadband noise of the reference is heavily filtered by a lowpass filter with a 3-dB cutoff frequency of 16 Hz.
AVDD
20 k
1 µF
REF3240
ENABLE
-
IN
-
Gnd_S
Out_S
Gnd_F
Out_F
+
10 k
+
1 µF
1k
+
OPA333
AVDD
+
THS4281
1 µF
0.2
AVDD
AVDD
REF AVDD
10 µF
AINP
V+
CONVST
ADS8860
AINM
GND
Figure 65. Reference Driver Circuit Schematic with VREF = 4 V
The reference buffer is designed with the THS4281 and OPA333 in a composite architecture to achieve superior
dc and ac performance at a reduced power consumption, compared to using a single high-performance amplifier.
The THS4281 is a high-bandwidth amplifier with a very low output impedance of 1 Ω at a frequency of 1 MHz.
The low output impedance makes the THS4281 a good choice for driving a high capacitive load to regulate the
voltage at the reference input of the ADC. The high offset and drift specifications of the THS4281 are corrected
by using a dc-correcting amplifier (OPA333) inside the feedback loop. The composite scheme inherits the
extremely low offset and temperature drift specifications of the OPA333.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
29
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
Reference Driver Circuit for VREF = 3 V in Ultralow Power, Lower Throughput Applications
The application circuit in Figure 66 shows the schematic of a complete reference driver circuit that generates a
voltage of 3 V dc using a single 3.3-V supply. This ultralow power reference block is suitable to drive the
ADS8860 for power-sensitive applications at a relatively lower throughput. This design uses the high-precision
REF3330 circuit that provides an accurate 3-V reference voltage at an extremely low quiescent current of 5 µA.
The output broadband noise of the reference is heavily filtered by a low-pass filter with a 3-dB cutoff frequency of
16 Hz.
1k AVDD
+ +
OPA333
GND
1 µF
AVDD
REF AVDD
100 nF
AVDD
10 k OUT
100 nF
IN
47 µF
REF3330
2.2 k AINP
V+
CONVST
ADS8860
AINM
10
GND
Figure 66. Reference Driver Circuit Schematic with VREF = 3 V
The reference buffer is designed with the low-power OPA333 that can operate from a 3.3-V supply at an
extremely low quiescent current of 28 µA. The AOL of amplifier interacting with a 47-µF capacitor, a 10-Ω ESR
(of a capacitor), and a 2.2-kΩ additional open-look output impedance limit the wideband noise contribution from
the amplifier to 3 kHz bandwidth. These three components are critical for good stability and maintaining the
amplifier with more than a 50° phase margin. In addition, the two 0.1-µF capacitors decouple the high-frequency
currents produced by the ADC reference input during conversions.
30
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
ADC INPUT DRIVER
The input driver circuit for a high-precision ADC mainly consists of two parts: a driving amplifier and a fly-wheel
RC filter. The amplifier is used for signal conditioning of the input voltage and its low output impedance provides
a buffer between the signal source and the switched capacitor inputs of the ADC. The RC filter helps attenuate
the sampling charge injection from the switched-capacitor input stage of the ADC and functions as an antialiasing
filter to band-limit the wideband noise contributed by the front-end circuit. Careful design of the front-end circuit is
critical to meet the linearity and noise performance of a high-precision, 16-bit ADC such as the ADS8860.
Input Amplifier Selection
Selection criteria for the input amplifiers is highly dependent on the input signal type and the performance goals
of the data acquisition system. Some key amplifier specifications to consider while selecting an appropriate
amplifier to drive the inputs of the ADC are:
• Small-signal bandwidth. Select the small-signal bandwidth of the input amplifiers to be as high as possible
after meeting the power budget of the system. Higher bandwidth reduces the closed-loop output impedance
of the amplifier, thus allowing the amplifier to more easily drive the low cutoff frequency RC filter (refer to the
Antialiasing Filter section) at the ADC inputs. Higher bandwidth also minimizes the harmonic distortion at
higher input frequencies. In order to maintain the overall stability of the input driver circuit, the amplifier
bandwidth should be selected as described in Equation 1:
•
§
·
1
¸¸
Unity Gain Bandwidth t 4 u ¨¨
© 2S u RFLT u CFLT ¹
(1)
Noise. Noise contribution of the front-end amplifiers should be as low as possible to prevent any degradation
in SNR performance of the system. As a rule of thumb, to ensure that the noise performance of the data
acquisition system is not limited by the front-end circuit, the total noise contribution from the front-end circuit
should be kept below 20% of the input-referred noise of the ADC. Noise from the input driver circuit is bandlimited by designing a low cutoff frequency RC filter, as explained in Equation 2.
2
§ V 1 _ AM P_ PP ·
S
¨
¸
NG u 2 u ¨ f
en2 _ RM S u u f3dB
¸
6
.
6
2
¨
¸
©
¹
d
§ SNR dB ·
¸
20
¹
¨
1 VREF
u
u 10 ©
5
2
where:
•
•
•
•
•
V1 / f_AMP_PP is the peak-to-peak flicker noise in µVRMS,
en_RMS is the amplifier broadband noise density in nV/√Hz,
f–3dB is the 3-dB bandwidth of the RC filter, and
NG is the noise gain of the front-end circuit, which is equal to '1' in a buffer configuration.
THD AMP d THD ADC 10 dB
•
(2)
Distortion. Both the ADC and the input driver introduce nonlinearity in a data acquisition block. As a rule of
thumb, to ensure that the distortion performance of the data acquisition system is not limited by the front-end
circuit, the distortion of the input driver should be at least 10 dB lower than the distortion of the ADC, as
shown in Equation 3.
(3)
Settling Time. For dc signals with fast transients that are common in a multiplexed application, the input signal
must settle within a 16-bit accuracy at the inputs of the ADS8860 during the acquisition time window. This
condition is critical to maintain the overall linearity performance of the ADC. Typically, the amplifier data
sheets specify the output settling performance only up to 0.1% to 0.001%, which may not be sufficient for the
desired 16-bit accuracy. Therefore, the settling behavior of the input driver should always be verified by
TINA™-SPICE simulations before selecting the amplifier.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
31
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
Antialiasing Filter
Converting analog-to-digital signals requires sampling an input signal at a constant rate. Any higher frequency
content in the input signal beyond half the sampling frequency is digitized and folded back into the low-frequency
spectrum. This process is called aliasing. Therefore, an analog, antialiasing filter must be used to remove the
harmonic content from the input signal before being sampled by the ADC. An antialiasing filter is designed as a
low-pass, RC filter, for which the 3-dB bandwidth is optimized based on specific application requirements. For dc
signals with fast transients (including multiplexed input signals), a high-bandwidth filter is designed to allow
accurately settling the signal at the ADC inputs during the small acquisition time window. For ac signals, the filter
bandwidth should be kept low to band-limit the noise fed into the ADC input, thereby increasing the signal-tonoise ratio (SNR) of the system.
Besides filtering the noise from the front-end drive circuitry, the RC filter also helps attenuate the sampling
charge injection from the switched-capacitor input stage of the ADC. A filter capacitor, CFLT, is connected across
the ADC inputs (as shown in Figure 67). This capacitor helps reduce the sampling charge injection and provides
a charge bucket to quickly charge the internal sample-and-hold capacitors during the acquisition process. As a
rule of thumb, the value of this capacitor should be at least 10 times the specified value of the ADC sampling
capacitance. For the ADS8860, the input sampling capacitance is equal to 59 pF. Thus, the value of CFLT should
be greater than 590 pF. The capacitor should be a COG- or NPO-type because these capacitor types have a
high-Q, low-temperature coefficient, and stable electrical characteristics under varying voltages, frequency, and
time.
RFLT ”22
f 3 dB
2S u R FLT
1
R FLT u C FLT
V
AINP
+
ADS8860
CFLT •590 pF
AINM
GND
RFLT ”22
Figure 67. Antialiasing Filter
Note that driving capacitive loads can degrade the phase margin of the input amplifiers, thus making the amplifier
marginally unstable. To avoid amplifier stability issues, series isolation resistors (RFLT) are used at the output of
the amplifiers. A higher value of RFLT is helpful from the amplifier stability perspective, but adds distortion as a
result of interactions with the nonlinear input impedance of the ADC. Distortion increases with source impedance,
input signal frequency, and input signal amplitude. Therefore, the selection of RFLT requires balancing the stability
and distortion of the design. For the ADS8860, TI recommends limiting the value of RFLT to a maximum of 22 Ω
in order to avoid any significant degradation in linearity performance. The tolerance of the selected resistors can
be chosen as 1% because the use of a differential capacitor at the input balances the effects resulting from any
resistor mismatch.
The input amplifier bandwidth should be much higher than the cutoff frequency of the antialiasing filter. TI
strongly recommends performing a SPICE simulation to confirm that the amplifier has more than a 40° phase
margin with the selected filter. Simulation is critical because even with high-bandwidth amplifiers, some amplifiers
might require more bandwidth than others to drive similar filters. If an amplifier has less than a 40° phase margin
with 22-Ω resistors, using a different amplifier with higher bandwidth or reducing the filter cutoff frequency with a
larger differential capacitor is advisable.
32
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
APPLICATION CIRCUIT EXAMPLES
This section describes some common application circuits using the ADS8860. These data acquisition (DAQ)
blocks are optimized for specific input types and performance requirements of the system. For simplicity, powersupply decoupling capacitors are not shown in these circuit diagrams; refer to the Power Supply section for
suggested guidelines.
DAQ Circuit for a 1-µs, Full-Scale Step Response
The application circuit shown in Figure 68 is optimized for using the ADS8860 at the maximum-specified
throughput of 1 MSPS for a full-scale step input voltage. Such step input signals are common in multiplexed
applications when switching between different channels.
In such applications, the primary design requirement is to ensure that the full-scale step input signal settles to a
16-bit accuracy at the ADC inputs. This condition is critical to achieve the excellent linearity specifications of the
ADC. Therefore, the bandwidth of the antialiasing RC filter should be large enough to allow optimal settling of the
input signal during the ADC acquisition time. The filter capacitor helps reduce the sampling charge injection at
the ADC inputs, but degrades the phase margin of the driving amplifier, thereby leading to stability issues.
Amplifier stability is maintained by the series isolation resistor. Therefore, the component values of the
antialiasing filter should be carefully selected to meet the settling requirements of the system and to maintain the
stability of the input driving amplifiers.
For the input driving amplifiers, key specifications include rail-to-rail input and output swing, high bandwidth, high
slew rate, and fast settling time. The OPA320 CMOS amplifier meets all these specification requirements for this
circuit with a single supply and low quiescent current.
REFERENCE DRIVE CIRCUIT
20 k 1 µF
THS4281
+
0.2
-
1k +
AVDD
OPA333
1 µF
+
1k +
REF3240
Vout
Vin
AVDD
AVDD
10 µF
Temp
1 µF
Trim
Gnd
1 µF
AVDD
+
VIN
AVDD
+
OPA320
15
-
REF AVDD
AINP
V+
1 nF
CONVST
ADS8860
AINM
GND
15
CONVST
INPUT DRIVER
16-Bit 1MSPS
SAR ADC
Figure 68. DAQ Circuit for a 1-µs, Full-Scale Step Response
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
33
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
DAQ Circuit for Lowest Distortion and Noise Performance at 1 MSPS
This section describes an application circuit (Figure 69) optimized for using the ADS8860 with lowest distortion
and noise performance at a throughput of 1 MSPS. The input signal is processed through a high-bandwidth, lowdistortion amplifier in an inverting gain configuration and a low-pass RC filter before being fed into the ADC.
As a rule of thumb, the distortion from the input driver should be at least 10 dB less than the ADC distortion. The
distortion resulting from variation in the common-mode signal is eliminated by using the amplifier in an inverting
gain configuration that establishes a fixed common-mode level for the circuit. This configuration also eliminates
the requirement of a rail-to-rail swing at the input of the amplifier. Therefore, the circuit uses the low-power
OPA836 as an input driver, which provides exceptional ac performance because of its extremely low-distortion,
high-bandwidth specifications.
In addition, the components of the antialiasing filter are such that the noise from the front-end circuit is kept low
without adding distortion to the input signal.
REFERENCE DRIVE CIRCUIT
20 k
1 µF
THS4281
+
-
1k
+
AVDD
OPA333
0.2
1 µF
+
1k
+
REF3240
Vout
Vin
AVDD
AVDD
10 µF
Temp
1 µF
Trim
Gnd
1 µF
1K
1K
AVDD
AVDD
VIN
+
OPA836
+
VCM
4.7
REF AVDD
V
+
AINP
10 nF
CONVST
ADS8860
AINM
4.7
GND
INPUT DRIVER
CONVST
16-Bit 1MSPS
SAR ADC
Figure 69. Differential Input DAQ Circuit for Lowest Distortion and Noise at 1 MSPS
34
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
ADS8860
www.ti.com
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
Ultralow-Power DAQ Circuit at 10 kSPS
The data acquisition circuit shown in Figure 70 is optimized for using the ADS8860 at a reduced throughput of 10
kSPS with ultralow-power consumption (< 300 µW) targeted at portable and battery-powered applications.
In order to save power, this circuit is operated on a single 3.3-V supply. The circuit uses the OPA333 with a
maximum quiescent current of 28 µA in order to drive the ADC input. The input amplifier is configured in a
modified unity-gain buffer configuration. The filter capacitor at the ADC inputs attenuates the sampling chargeinjection noise from the ADC but effects the stability of the input amplifiers by degrading the phase margin. This
attenuation requires a series isolation resistor to maintain amplifier stability. The value of the series resistor is
directly proportional to the open-loop output impedance of the driving amplifier to maintain stability, which is high
(in the order of kΩ) in the case of low-power amplifiers such as the OPA333. Therefore, a high value of 1 kΩ is
selected for the series resistor at the ADC inputs. However, this series resistor creates an additional voltage drop
in the signal path, thereby leading to linearity and distortion issues. The dual-feedback configuration used in
Figure 70 corrects for this additional voltage drop and maintains system performance at ultralow-power
consumption.
REFERENCE DRIVE CIRCUIT
1k
REF3330
IN
10 k
+ +
OUT
2.2 k
OPA333
100 nF
100 nF
3.3 V
10
3.3 V
47 µF
1 µF
GND
INPUT DRIVER
3.3V
20 k
2.4 nF
REF
-
1k
AVDD
CONVST
AINP
OPA333
3.3 V
ADS8860
2.4 nF
+ +
VIN
CONVST
AINM
GND
16-Bit 1MSPS
SAR ADC
Figure 70. Ultralow-Power DAQ Circuit at 10 kSPS
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
35
ADS8860
SBAS569A – MAY 2013 – REVISED DECEMBER 2013
www.ti.com
REVISION HISTORY
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Original (May 2013) to Revision A
Page
•
Changed sub-bullets of AC and DC Performance Features bullet ....................................................................................... 1
•
Changed Full-Scale Step Settling Features bullet ................................................................................................................ 1
•
Deleted last two Applications bullets .................................................................................................................................... 1
•
Changed Description section ................................................................................................................................................ 1
•
Changed front page graphic ................................................................................................................................................. 1
•
Added Family Information, Absolute Maximum Ratings, and Thermal Information tables ................................................... 2
•
Added Electrical Characteristics table .................................................................................................................................. 3
•
Added Timing Characteristics section .................................................................................................................................. 5
•
Added Pin Configurations section ......................................................................................................................................... 9
•
Added Typical Characteristics section ................................................................................................................................ 10
•
Added Overview section ..................................................................................................................................................... 17
•
Added Application Information section ............................................................................................................................... 29
36
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: ADS8860
PACKAGE OPTION ADDENDUM
www.ti.com
15-Jan-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
ADS8860IDGS
ACTIVE
VSSOP
DGS
10
80
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
8860
ADS8860IDGSR
ACTIVE
VSSOP
DGS
10
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
8860
ADS8860IDRCR
ACTIVE
SON
DRC
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
8860
ADS8860IDRCT
ACTIVE
SON
DRC
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
8860
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
15-Jan-2014
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
31-Dec-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
ADS8860IDGSR
Package Package Pins
Type Drawing
VSSOP
DGS
10
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2500
330.0
12.4
Pack Materials-Page 1
5.3
B0
(mm)
K0
(mm)
P1
(mm)
3.4
1.4
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
31-Dec-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ADS8860IDGSR
VSSOP
DGS
10
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
ADS8860IDRCR ADS8860IDRCT ADS8860IDGS ADS8860IDGSR
Similar pages