TI1 DRV425RTJR Drv425 fluxgate magnetic-field sensor Datasheet

Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
DRV425
SBOS729 – OCTOBER 2015
DRV425 Fluxgate Magnetic-Field Sensor
1 Features
3 Description
•
The DRV425 is designed for single-axis magnetic
field-sensing applications and enables electricallyisolated, high-sensitivity, and precise dc- and ac-field
measurements. The device provides the unique and
proprietary, integrated fluxgate sensor (IFG) with an
internal compensation coil to support a high-accuracy
sensing range of ±2 mT with a measurement
bandwidth of up to 47 kHz. The low offset, offset drift,
and noise of the sensor, combined with the precise
gain, low gain drift, and very low nonlinearity provided
by the internal compensation coil, result in unrivaled
magnetic field measurement precision. The output of
the DRV425 is an analog signal proportional to the
sensed magnetic field.
1
•
•
•
•
•
High-Precision, Integrated Fluxgate Sensor:
– Offset: ±8 µT (Max)
– Offset Drift: ±5 nT/°C (Typ)
– Gain Error: 0.04% (Typ)
– Gain Drift: ±7 ppm/°C (Typ)
– Linearity: ±0.1%
– Noise: 1.5 nT/√Hz (Typ)
Sensor Range: ±2 mT (Max)
– Range and Gain Adjustable with External
Resistor
Selectable Bandwidth: 47 kHz or 32 kHz
Precision Reference:
– Accuracy: 2% (max), Drift: 50 ppm/°C (max)
– Pin-Selectable Voltage: 2.5 V or 1.65 V
– Selectable Ratiometric Mode: VDD / 2
Diagnostic Features: Overrange and Error Flags
Supply Voltage Range: 3.0 V to 5.5 V
The DRV425 offers a complete set of features,
including an internal difference amplifier, on-chip
precision reference, and diagnostic functions to
minimize component count and system-level cost.
The DRV425 is available in a thermally-enhanced,
non-magnetic, thin WQFN package with a
PowerPAD™ for optimized heat dissipation, and is
specified for operation over the extended industrial
temperature range of –40°C to +125°C.
2 Applications
•
•
•
•
Linear Position Sensing
Current Sensing in Busbars
Over-the-Trace Current Sensing
General-Purpose Magnetic-Field Sensors
Device Information
PART NUMBER
DRV425
PACKAGE
WQFN (20)
(1)
BODY SIZE (NOM)
4.00 mm × 4.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Schematic
RSHUNT
COMP1
COMP2
DRV2
DRV1 AINP
AINN
DRV425
Fluxgate
Sensor
and
Compensation
Coil
Differential
Driver
Shunt
Sense
Amplifier
Integrator
VOUT
ADC
REFIN
Fluxgate Sensor Front-End
Device Control and Diagnostic
Reference
REFOUT
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
DRV425
SBOS729 – OCTOBER 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
4
4
4
4
5
7
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
8
8.1 Application Information............................................ 24
8.2 Typical Applications ................................................ 24
9
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
Power-Supply Recommendations...................... 29
9.1 Power-Supply Decoupling....................................... 29
9.2 Power-On Start-Up and Brownout .......................... 29
9.3 Power Dissipation ................................................... 29
10 Layout................................................................... 30
10.1 Layout Guidelines ................................................. 30
10.2 Layout Example .................................................... 31
11 Device and Documentation Support ................. 32
11.1
11.2
11.3
11.4
11.5
Detailed Description ............................................ 17
7.1
7.2
7.3
7.4
Application and Implementation ........................ 24
17
17
18
23
Documentation Support .......................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
32
32
32
32
32
12 Mechanical, Packaging, and Orderable
Information ........................................................... 32
4 Revision History
2
DATE
REVISION
NOTES
October 2015
*
Initial release.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
DRV425
www.ti.com
SBOS729 – OCTOBER 2015
5 Pin Configuration and Functions
GND
ERROR
GND
COMP2
COMP1
20
19
18
17
16
RTJ Package
WQFN-20
Top View
BSEL
1
15
OR
RSEL1
2
14
AINN
RSEL0
3
13
AINP
REFOUT
4
12
DRV1
REFIN
5
11
DRV2
6
7
8
9
10
VOUT
GND
VDD
VDD
GND
(Thermal Pad)
Pin Functions
PIN
NO.
I/O
AINN
NAME
14
I
Inverting input of the shunt-sense amplifier
AINP
13
I
Noninverting input of the shunt-sense amplifier
BSEL
1
I
Filter bandwidth select input
COMP1
16
I
Internal compensation coil input 1
COMP2
17
I
Internal compensation coil input 2
DRV1
12
O
Compensation coil driver output 1
DRV2
11
O
Compensation coil driver output 2
ERROR
19
O
Error flag: open-drain, active-low output
7, 10, 18, 20
—
Ground reference
O
Shunt-sense amplifier overrange indicator: open-drain, active-low output
—
Connect the thermal pad to GND
GND
OR
15
PowerPAD
DESCRIPTION
REFIN
5
I
Common-mode reference input for the shunt-sense amplifier
REFOUT
4
O
Voltage reference output
RSEL0
3
I
Voltage reference mode selection input 0
RSEL1
2
I
Voltage reference mode selection input 1
8, 9
—
Supply voltage, 3.0 V to 5.5 V. Decouple both pins using 1-µF ceramic capacitors placed as
close as possible to the device. See the Power-Supply Decoupling and Layout sections for
further details.
6
O
Shunt-sense amplifier output
VDD
VOUT
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
3
DRV425
SBOS729 – OCTOBER 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MIN
MAX
–0.3
6.5
Input voltage, except AINP and AINN pins (2)
GND – 0.5
VDD + 0.5
Shunt-sense amplifier inputs (AINP and AINN pins) (3)
GND – 6.0
VDD + 6.0
–300
300
Supply voltage (VDD to GND)
Voltage
DRV1 and DRV2 pins (short-circuit current, IOS) (4)
Current
Temperature
(1)
(2)
(3)
(4)
Shunt-sense amplifier input pins AINP and AINN
–5
5
All remaining pins
–25
25
Junction, TJ max
–50
150
Storage, Tstg
–65
150
UNIT
V
mA
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Input pins are diode-clamped to the power-supply rails. Input signals that can swing more than 0.5 V beyond the supply rails must be
current limited, except for the differential amplifier input pins.
These inputs are not diode-clamped to the power-supply rails.
Power-limited; observe maximum junction temperature.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001
Electrostatic discharge
(1)
±2000
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
±1000
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
VDD
Supply voltage range (VDD to GND)
3.0
5.0
5.5
UNIT
V
TA
Specified ambient temperature range
–40
125
°C
6.4 Thermal Information
DRV425
THERMAL METRIC
(1)
RTJ (WQFN)
UNIT
20 PINS
RθJA
Junction-to-ambient thermal resistance
34.1
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
33.1
°C/W
RθJB
Junction-to-board thermal resistance
11
°C/W
ψJT
Junction-to-top characterization parameter
0.3
°C/W
ψJB
Junction-to-board characterization parameter
11
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
2.1
°C/W
(1)
4
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
DRV425
www.ti.com
SBOS729 – OCTOBER 2015
6.5 Electrical Characteristics
All minimum and maximum specifications are at TA = 25°C, VDD = 3.0 V to 5.5 V, and IDRV1 = IDRV2 = 0 mA, unless otherwise
noted. Typical values are at VDD = 5.0 V.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
–8
±2
8
UNIT
FLUXGATE SENSOR FRONT-END
G
Offset
No magnetic field
Offset drift
No magnetic field
Gain
Current at DRV1 and DRV2 outputs
±5
12.2
Gain error
µT
nT/°C
mA/mT
±0.04%
Gain drift
Best-fit line method
±7
Linearity error
ppm/°C
0.1%
Hysteresis
Magnetic field sweep from –10 mT to 10 mT
1.4
µT
Noise
f = 0.1 Hz to 10 Hz
17
nTrms
Noise density
f = 1 kHz
Compensation range
Saturation trip level for the
ERROR pin (1)
Open-loop, uncompensated field
ERROR delay
Open-loop at B > 1.6 mT
BW
Bandwidth
IOS
Short-circuit current
1.5
–2
mT
4 to 6
µs
32
BSEL = 1, RSHUNT = 22 Ω
47
VDD = 5 V
250
VDD = 3.3 V
150
Compensation coil resistance
mT
1.6
BSEL = 0, RSHUNT = 22 Ω
Common-mode output voltage at the
DRV1 and DRV2 pins
nT/√Hz
2
kHz
mA
VREFOUT
V
100
Ω
SHUNT-SENSE AMPLIFIER
VOO
Output offset voltage
VAINP = VAINN = VREFIN, VDD = 3.0 V
Output offset voltage drift
CMRR
Common-mode rejection ratio, RTO (2)
VCM = –1 V to VDD + 1 V, VREFIN = VDD / 2
PSRRAMP
Power-supply rejection ratio, RTO (2)
VDD = 3.0 V to 5.5 V, VCM = VREFIN
VICR
Common-mode input voltage range
zid
Differential input impedance
zic
Common-mode input impedance
Gnom
Nominal gain
EG
Gain error
–0.075
±0.01
0.075
–2
±0.4
2
µV/°C
–250
±50
250
µV/V
–50
±4
50
µV/V
–1
Gain error drift
V
kΩ
20
23.5
40
50
60
4
±0.02%
0.3%
–5
±1
5
12
Voltage output swing from negative
rail (OR pin trip level) (1)
48
85
VDD = 3.0 V, IVOUT = 2.5 mA
56
100
Voltage output swing from positive rail
(OR pin trip level) (1)
VDD = 5.5 V, IVOUT = –2.5 mA
VDD – 85
VDD – 48
VDD = 3.0 V, IVOUT = –2.5 mA
VDD – 100
VDD – 56
IOS
Short-circuit current
BW–3dB
Bandwidth
SR
Slew rate
VIN = 1-V step
–18
VOUT connected to VDD
20
Large signal
ΔV = ± 2 V to 1%, no external filter
Small signal
ΔV = ± 0.4 V to 0.01%
tsa
Settling time
en
Output voltage noise density
f = 1 kHz, compensation loop disabled
VREFIN
Input voltage range at pin REFIN
Input voltage range at REFIN pin
µs
mA
2
MHz
6.5
V/µs
0.9
µs
8
170
GND
mV
mV
2.5 to 3.5
VOUT connected to GND
ppm/°C
ppm
VDD = 5.5 V, IVOUT = 2.5 mA
Signal overrange indication delay
(OR pin) (1)
kΩ
V/V
–0.3%
Linearity error
(1)
(2)
VDD + 1
16.5
VVOUT / (VAINP – VAINN)
mV
nV/√Hz
VDD
V
See the Magnetic Field Range, Overrange Indicator, and Error Flag section for details on the behavior of the ERROR and OR outputs.
Parameter value is referred-to-output (RTO).
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
5
DRV425
SBOS729 – OCTOBER 2015
www.ti.com
Electrical Characteristics (continued)
All minimum and maximum specifications are at TA = 25°C, VDD = 3.0 V to 5.5 V, and IDRV1 = IDRV2 = 0 mA, unless otherwise
noted. Typical values are at VDD = 5.0 V.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VOLTAGE REFERENCE
Reference output voltage at the
REFOUT pin
VREFOUT
PSRRREF
ΔVO(ΔIO)
IOS
RSEL[1:0] = 00, no load
2.45
2.5
2.55
RSEL[1:0] = 01, no load
1.6
1.65
1.7
RSEL[1:0] = 1x, no load
45
50
55
% of
VDD
V
Reference output voltage drift
RSEL[1:0] = 0x
–50
±10
50
ppm/°C
Voltage divider gain error drift
RSEL[1:0] = 1x
–50
±10
50
ppm/°C
Power-supply rejection ratio
RSEL[1:0] = 0x
–300
±15
300
µV/V
RSEL[1:0] = 0x, load to GND or VDD,
ΔILOAD = 0 mA to 5 mA, TA = –40°C to +125°C
0.15
0.35
RSEL[1:0] = 1x, load to GND or VDD,
ΔILOAD = 0 mA to 5 mA, TA = –40°C to +125°C
0.3
0.8
Load regulation
Short-circuit current
mV/mA
REFOUT connected to VDD
20
mA
REFOUT connected to GND
–18
mA
DIGITAL INPUTS/OUTPUTS (CMOS)
IIL
Input leakage current
VIH
High-level input voltage
TA = –40°C to +125°C
0.7 × VDD
0.01
VDD + 0.3
µA
V
VIL
Low-level input voltage
TA = –40°C to +125°C
–0.3
0.3 × VDD
V
VOH
High-level output voltage
Open-drain output
VOL
Low-level output voltage
4-mA sink current
Set by external pullup resistor
V
0.3
V
POWER SUPPLY
IQ
VPOR
6
Quiescent current
IDRV1/2 = 0 mA, 3.0 V ≤ VDD ≤ 3.6 V,
TA = –40°C to +125°C
6
8
IDRV1/2 = 0 mA, 4.5 V ≤ VDD ≤ 5.5 V,
TA = –40°C to +125°C
7
10
Power-on reset threshold
mA
2.4
Submit Documentation Feedback
V
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
DRV425
www.ti.com
SBOS729 – OCTOBER 2015
6.6 Typical Characteristics
50
40
40
D001
Offset (PT)
3
3
2
2
1
1
0
-1
8
7
6
5
4
3
2
1
-1
-2
-3
-3
5
Device 1
Device 2
Device 3
0
-2
-4
-4
-40
5.5
-25
-10
5
D003
Figure 3. Fluxgate Sensor Front-End Offset vs
Supply Voltage
20 35 50 65
Temperature (°C)
80
95
110 125
D004
Figure 4. Fluxgate Sensor Front-End Offset vs
Temperature
50
100
40
80
Devices (%)
30
20
60
40
20
10
D005
12.3
12.28
12.26
12.24
12.22
12.2
12.18
12.16
12.14
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
5
10
15
20
25
30
35
40
45
50
Offset Drift (nT/qC)
12.12
0
0
12.1
Devices (%)
0
Figure 2. Fluxgate Sensor Front-End Offset Histogram
4
Offset (PT)
Offset (PT)
Figure 1. Fluxgate Sensor Front-End Offset Histogram
4
4.5
Supply Voltage (V)
-1
VDD = 3.3 V
4
3.5
D002
Offset (PT)
VDD = 5 V
3
-2
-3
-8
8
7
6
5
4
3
2
1
0
-1
-2
-3
-4
0
-5
0
-6
10
-7
10
-4
20
-5
20
30
-6
30
-7
Devices (%)
50
-8
Devices (%)
at VDD = 5 V and TA = 25°C (unless otherwise noted)
D046
Gain (mA/mT)
VDD = 5 V
Figure 5. Fluxgate Sensor Front-End Offset Drift Histogram
Figure 6. Fluxgate Sensor Front-End Gain Histogram
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
7
DRV425
SBOS729 – OCTOBER 2015
www.ti.com
Typical Characteristics (continued)
12.35
12.35
12.3
12.3
12.25
12.25
Gain (mA/mT)
Gain (mA/mT)
at VDD = 5 V and TA = 25°C (unless otherwise noted)
12.2
12.15
12.1
Device 1
Device 2
Device 3
12.2
12.15
12.1
12.05
3
3.5
4
4.5
Supply Voltage (V)
5
12.05
-40
5.5
-25
-10
D008
Figure 7. Fluxgate Sensor Front-End Gain vs
Supply Voltage
5
20 35 50 65
Temperature (°C)
80
95
110 125
D009
Figure 8. Fluxgate Sensor Front-End Gain vs Temperature
50
0.2
0.175
40
Linearity (%)
Devices (%)
0.15
30
20
0.125
0.1
0.075
0.05
10
0.025
0.14
0.13
0.12
0.11
0.1
0.09
0.08
0.07
0.06
0.05
0
0
3
3.5
D057
4
4.5
Supply Voltage (V)
5
5.5
D010
Linearity (%)
VDD = 5 V
Figure 9. Fluxgate Sensor Front-End Linearity Histogram
Figure 10. Fluxgate Sensor Front-End Linearity vs
Supply Voltage
100
0.2
Device 1
Device 2
Device 3
Noise Density (nT/—Hz)
0.175
Linearity (%)
0.15
0.125
0.1
0.075
0.05
10
1
0.025
0
-40
-25
-10
5
20 35 50 65
Temperature (°C)
80
95
110 125
D011
Figure 11. Fluxgate Sensor Front-End Linearity vs
Temperature
8
0.1
0.0001
0.001
0.01
0.1
1
Noise Frequency (kHz)
10
100
D006
Figure 12. Fluxgate Sensor Front-End Noise Density vs
Noise Frequency
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
DRV425
www.ti.com
SBOS729 – OCTOBER 2015
Typical Characteristics (continued)
80
70
70
60
60
50
50
D007
Saturation Trip Level (mT)
2.1
2
1.9
1.8
1.3
2.1
2
1.9
0
1.8
0
1.7
10
1.6
10
1.5
20
1.4
20
1.7
30
1.6
30
40
1.5
40
1.4
Devices (%)
80
1.3
Devices (%)
at VDD = 5 V and TA = 25°C (unless otherwise noted)
D013
Saturation Trip Level (mT)
VDD = 5 V
VDD = 3.3 V
Figure 13. Fluxgate Sensor Saturation (ERROR Pin)
Trip Level Histogram
Figure 14. Fluxgate Sensor Saturation (ERROR Pin)
Trip Level Histogram
2
60
50
1.8
1.7
Devices (%)
1.6
1.5
40
30
20
1.4
10
1.3
114
112
110
108
D052
106
0
110 125
104
95
102
80
100
20 35 50 65
Temperature (°C)
98
5
96
-10
94
-25
90
1.2
-40
92
Saturation Trip Level (mT)
1.9
D053
Compensation Coil Resistance (:)
Figure 16. Compensation Coil Resistance Histogram
150
70
140
60
130
50
30
90
20
80
10
D054
0
50
110 125
40
95
30
80
20
20 35 50 65
Temperature (°C)
10
5
0
-10
-10
-25
-50
70
-40
-20
100
40
-30
110
-40
120
Devices (%)
Compensation Coil Resistance (:)
Figure 15. Fluxgate Sensor Saturation (ERROR Pin) Trip
Level vs Temperature
Output Offset (PV)
D015
VDD = 5 V
Figure 17. Compensation Coil Resistance vs Temperature
Figure 18. Shunt-Sense Amplifier Output Offset Histogram
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
9
DRV425
SBOS729 – OCTOBER 2015
www.ti.com
Typical Characteristics (continued)
at VDD = 5 V and TA = 25°C (unless otherwise noted)
70
75
60
50
Output Offset (PV)
Devices (%)
50
40
30
20
25
0
-25
50
40
30
20
10
0
-10
-20
-75
-30
0
-40
-50
-50
10
3
3.5
4
4.5
Supply Voltage (V)
D015
D016
Output Offset (PV)
5
5.5
D018
VDD = 3.3 V
Figure 20. Shunt-Sense Amplifier Output Offset vs
Supply Voltage
Figure 19. Shunt-Sense Amplifier Output Offset Histogram
75
50
Device 1
Device 2
Device 3
40
25
Devices (%)
Output Offset (PV)
50
0
30
20
-25
10
-50
0
-25
-10
5
20 35 50 65
Temperature (°C)
80
95
-250
-225
-200
-175
-150
-125
-100
-75
-50
-25
0
25
50
75
100
125
150
175
200
225
250
-75
-40
110 125
Common-Mode Rejection Ratio (PV/V)
D017
Figure 21. Shunt-Sense Amplifier Output Offset vs
Temperature
Figure 22. Shunt-Sense Amplifier CMRR Histogram
70
60
80
50
Devices (%)
60
40
40
30
20
20
50
40
30
20
10
0
Power-Supply Rejection Ratio (PV/V)
D020
Figure 23. Shunt-Sense Amplifier CMRR vs
Input Signal Frequency
-10
1000
-20
1
10
100
Input Signal Frequency (kHz)
-30
0
0.1
-40
0
0.01
10
-50
Common-Mode Rejection Ratio (dB)
100
10
D019
D021
Figure 24. Shunt-Sense Amplifier PSRR Histogram
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
DRV425
www.ti.com
SBOS729 – OCTOBER 2015
Typical Characteristics (continued)
100
100
80
80
Devices (%)
60
40
60
40
20
20
60
58
56
54
52
50
1000
48
100
46
1
10
Ripple Frequency (kHz)
44
0.1
42
0
0
0.01
40
Power-Supply Rejection Ratio (dB)
at VDD = 5 V and TA = 25°C (unless otherwise noted)
D023
AINP Input Impedance (k:)
D022
Figure 26. Shunt-Sense Amplifier AINP Input Impedance
Histogram
Figure 25. Shunt-Sense Amplifier PSRR vs
Ripple Frequency
50
51
40
50.6
50.4
Devices (%)
50.2
50
49.8
30
20
49.6
10
49.4
49.2
12
11.75
11
10
9.5
9
8.5
11.5
110 125
11.25
95
10.5
80
10.75
20 35 50 65
Temperature (°C)
10.25
5
9.75
-10
9.25
-25
8.75
0
8
49
-40
8.25
AINP Input Impedance (k:)
50.8
D025
AINN Input Impedance (k:)
D024
Figure 27. Shunt-Sense Amplifier AINP Input Impedance
vs Temperature
Figure 28. Shunt-Sense Amplifier AINN Input Impedance
Histogram
100
11
80
10.6
10.4
Devices (%)
AINN Input Impedance (k:)
10.8
10.2
10
9.8
60
40
9.6
20
9.4
9.2
D026
0.1
0.08
0.06
0.04
110 125
0.02
95
0
80
-0.02
20 35 50 65
Temperature (°C)
-0.04
5
-0.06
-10
-0.08
0
-25
-0.1
9
-40
D027
Gain Error (%)
Including IFG, VDD = 5 V
Figure 29. Shunt-Sense Amplifier AINN Input Impedance
vs Temperature
Figure 30. Shunt-Sense Amplifier Gain Error Histogram
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
11
DRV425
SBOS729 – OCTOBER 2015
www.ti.com
Typical Characteristics (continued)
at VDD = 5 V and TA = 25°C (unless otherwise noted)
100
0.3
0.25
0.2
80
Gain Error (%)
Devices (%)
0.15
60
40
0.1
0.05
0
-0.05
-0.1
-0.15
20
-0.2
-0.25
-0.3
-40
0.1
0.08
0.06
0.04
0.02
0
-0.02
-0.04
-0.06
-0.08
-0.1
0
-25
-10
D055
5
20 35 50 65
Temperature (°C)
80
95
110 125
D028
Gain Error (%)
Including IFG, VDD = 3.3 V
Figure 32. Shunt-Sense Amplifier Gain Error vs
Temperature
Figure 31. Shunt-Sense Amplifier Gain Error Histogram
20
40
35
Linearity Error (ppm)
Gain (dB)
15
10
5
30
25
20
15
10
5
0
0.01
0
0.1
1
10
100
Input Signal Frequency (kHz)
1000
10000
3
Figure 33. Shunt-Sense Amplifier Gain vs
Input Signal Frequency
5
5.5
D030
0.5
VDD = 5.5 V
VDD = 3.0 V
Voltage Difference to VDD or GND (V)
Voltage Difference to VDD or GND (V)
4
4.5
Supply Voltage (V)
Figure 34. Shunt-Sense Amplifier Linearity Error vs
Supply Voltage
0.5
0.4
0.3
0.2
0.1
0
0.4
0.3
0.2
0.1
0
0
1
2
3
4
5
6
7
Output Current (mA)
8
9
10
3
3.5
D031
Figure 35. OR Pin Trip Level vs Output Current
12
3.5
D029
4
4.5
Supply Voltage (V)
5
5.5
D056
Figure 36. OR Pin Trip Level vs Supply Voltage
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
DRV425
www.ti.com
SBOS729 – OCTOBER 2015
Typical Characteristics (continued)
at VDD = 5 V and TA = 25°C (unless otherwise noted)
4
VDD = 5.5 V
VDD = 3.0 V
3.75
0.4
3.5
Trip Delay (Ps)
Voltage Difference to VDD or GND (V)
0.5
0.3
0.2
3.25
3
2.75
2.5
0.1
2.25
0
-40
-25
-10
5
20 35 50 65
Temperature (°C)
80
95
2
-40
110 125
-25
Figure 37. OR Pin Trip Level vs Temperature
20 35 50 65
Temperature (°C)
80
95
110 125
D033
40
VOUT to GND
VOUT to VDD
VOUT to GND
VOUT to VDD
30
Short-Circuit Current (mA)
30
Short-Circuit Current (mA)
5
Figure 38. OR Pin Trip Delay vs Temperature
40
20
10
0
-10
-20
-30
20
10
0
-10
-20
-30
-40
3
3.5
4
4.5
Supply Voltage (V)
5
-40
-40
5.5
-25
-10
5
D035
Figure 39. Shunt-Sense Amplifier Output Short-Circuit
Current vs Supply Voltage
20 35 50 65
Temperature (°C)
80
95
110 125
D034
Figure 40. Shunt-Sense Amplifier Output Short-Circuit
Current vs Temperature
0.25
0.25
0.2
0.2
0.15
0.15
VVOUT
VAINP - VAINN
0.1
Voltage (V)
0.1
Voltage (V)
-10
D032
0.05
0
-0.05
0.05
0
-0.05
-0.1
-0.1
-0.15
-0.15
VVOUT
VAINP - VAINN
-0.2
-0.25
-2.5
0
2.5
5
7.5
10
Time (Ps)
12.5
15
-0.2
17.5
-0.25
-2.5
D012
Rising edge
0
2.5
5
7.5
10
Time (Ps)
12.5
15
17.5
D049
Falling edge
Figure 41. Shunt-Sense Amplifier Small-Signal
Settling Time
Figure 42. Shunt-Sense Amplifier Small-Signal
Settling Time
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
13
DRV425
SBOS729 – OCTOBER 2015
www.ti.com
Typical Characteristics (continued)
at VDD = 5 V and TA = 25°C (unless otherwise noted)
1.25
1.25
1
1
0.75
0.75
0.5
Voltage (V)
0.5
0.25
0
-0.25
0.25
0
-0.25
-0.5
-0.5
-0.75
-0.75
VVOUT
VAINP - VAINN
-1
-1.25
-0.5
0
0.5
1
Time (Ps)
1.5
2
-1
-1.25
-0.5
2.5
0
0.5
Rising edge
2
2.5
D051
Figure 44. Shunt-Sense Amplifier Large-Signal
Settling Time
5
5
VAINP - VAINN
VVOUT
4
3
3
2
2
1
0
-1
1
0
-1
-2
-2
-3
-3
-4
-4
-5
-0.1
-0.075 -0.05 -0.025
0
0.025
Time (ms)
0.05
0.075
VAINP - VAINN
VVOUT
4
Voltage (V)
-5
-0.1
0.1
D036
-0.075 -0.05 -0.025
0
0.025
Time (ms)
VDD = 5 V
0.05
0.075
0.1
D037
VDD = 3.3 V
Figure 45. Shunt-Sense Amplifier Overload Recovery
Response
Figure 46. Shunt-Sense Amplifier Overload Recovery
Response
10000
70
60
50
Devices (%)
1000
100
40
30
20
10
2.505
2.504
2.503
2.502
2.501
D038
2.498
100000
2.497
1000
10000
Noise Frequency (Hz)
2.496
0
100
2.495
10
10
2.5
Voltage (V)
1.5
Falling edge
Figure 43. Shunt-Sense Amplifier Large-Signal
Settling Time
Output Voltage Noise Density (nV/—Hz)
1
Time (Ps)
D050
2.499
Voltage (V)
VVOUT
VAINP - VAINN
D039
Reference Voltge (V)
VREFOUT = 2.5 V
Figure 47. Shunt-Sense Amplifier Output Voltage Noise
Density vs Noise Frequency
14
Submit Documentation Feedback
Figure 48. Reference Voltage Histogram
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
DRV425
www.ti.com
SBOS729 – OCTOBER 2015
Typical Characteristics (continued)
at VDD = 5 V and TA = 25°C (unless otherwise noted)
3
60
2.8
Reference Voltage (V)
70
Devices (%)
50
40
30
20
2.6
2.4
2.2
2
1.8
1.655
1.654
1.653
1.652
1.651
1.65
1.649
1.4
1.648
0
1.647
1.6
1.646
10
1.645
RSEL[1:0] = 00
RSEL[1:0] = 01
3
3.5
D058
4
4.5
Supply Voltage (V)
5
5.5
D042
Reference Voltage (V)
VREFOUT = 1.65 V
Figure 50. Reference Voltage vs Supply Voltage
Figure 49. Reference Voltage Histogram
3
2.55
Device 1
Device 2
Device 3
2.54
Reference Voltage (V)
Reference Voltage (V)
2.53
RSEL[1:0] = 00
RESL[1:0] = 01
RSEL[1:0] = 1x
2.8
2.52
2.51
2.5
2.49
2.48
2.6
2.4
2.2
2
1.8
2.47
1.6
2.46
2.45
-40
-25
-10
5
20 35 50 65
Temperature (°C)
80
95
1.4
-5
110 125
Figure 51. Reference Voltage vs Temperature
-3
-2
-1
0
1
2
Referene Current (mA)
3
4
5
D043
Figure 52. Reference Voltage vs Reference Output Current
30
50
25
40
20
15
10
30
20
10
0
0
-20
-18
-16
-14
-12
-10
-8
-6
-4
-2
0
2
4
6
8
10
12
14
16
18
20
5
D041
Reference Voltage Drift (ppm/qC)
-300
-270
-240
-210
-180
-150
-120
-90
-60
-30
0
30
60
90
120
150
180
210
240
270
300
Devices (%)
Devices (%)
-4
D040
D044
Power-Supply Rejection Ratio (PV/V)
Figure 53. Reference Voltage Drift Histogram
Figure 54. Reference Voltage PSRR Histogram
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
15
DRV425
SBOS729 – OCTOBER 2015
www.ti.com
Typical Characteristics (continued)
at VDD = 5 V and TA = 25°C (unless otherwise noted)
100
30
REFOUT to GND
REFOUT to VDD
25
Short-Circuit Current (mA)
Devices (%)
80
60
40
20
20
15
10
5
0
-5
-10
-15
0.3
0.35
0.2
0.25
0.15
0.1
0
0.05
-0.1
-0.05
-0.2
-0.15
-0.25
-0.3
-0.35
0
-20
-40
-25
-10
5
20 35 50 65
Temperature (°C)
D045
80
95
110 125
D060
Load Regulation (mV/mA)
Figure 56. Reference Short-Circuit Current vs Temperature
Figure 55. Reference Voltage Load Regulation Histogram
10
10
VDD = 3.3 V
VDD = 5 V
9
Quiescent Current (mA)
Quiescent Current (mA)
9.5
8
7
9
8.5
8
7.5
7
6.5
6
6
5.5
5
-40
5
3
3.5
4
4.5
Supply Voltage (V)
5
5.5
-10
5
20 35 50 65
Temperature (°C)
80
95
110 125
D048
Figure 58. Quiescent Current vs Temperature
Figure 57. Quiescent Current vs Supply Voltage
2.55
40
VDD = 3.3 V
VDD = 5 V
35
30
Reset Threshold (V)
Supply Current (mA)
-25
D061
25
20
15
10
2.45
2.35
5
0
0
0.25
0.5
0.75
1
1.25
Magnetic Field (mT)
1.5
1.75
2.25
-40
-25
D014
Figure 59. Supply Current vs Magnetic Field
16
2
-10
5
20 35 50 65
Temperature (°C)
80
95
110 125
D047
Figure 60. Power-On Reset Threshold vs Temperature
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
DRV425
www.ti.com
SBOS729 – OCTOBER 2015
7 Detailed Description
7.1 Overview
Magnetic sensors are used in a broad range of applications (such as position, indirect ac and dc current, or
torque measurement). Hall-effect sensors are most common in magnetic field sensing, but their offset, noise,
gain variation, and nonlinearity limit the achievable resolution and accuracy of the system. Fluxgate sensors offer
significantly higher sensitivity, lower drift, lower noise, and high linearity and enable up to 1000-times better
accuracy of the measurement.
As shown in the Functional Block Diagram section, the DRV425 consists of a magnetic fluxgate sensor with the
necessary sensor conditioning and compensation coil to internally close the control loop. The fluxgate sensor is
repeatedly driven in and out of saturation and supports hysteresis-free operation with excellent accuracy. The
internal compensation coil assures stable gain and high linearity.
The magnetic field (B) is detected by the internal fluxgate sensor in the DRV425. The device integrates the
sensor output to assure high-loop gain. The integrator output connects to the built-in differential driver that drives
an opposing compensation current through the internal compensation coil. The compensation coil generates an
opposite magnetic field that brings the original magnetic field at the sensor back to zero.
The compensation current is proportional to the external magnetic field and its value is 12.2 mA/mT. This
compensation current generates a voltage drop across an external shunt resistor, RSHUNT. An integrated
difference amplifier with a fixed gain of 4 V/V measures this voltage and generates an output voltage that is
referenced to REFIN and is proportional to the magnetic field. The value of the output voltage at the VOUT pin
(VVOUT) is calculated using Equation 1:
VVOUT [V] = B × G × RSHUNT × GAMP = B [mT] × 12.2 mA/mT × RSHUNT [Ω] × 4 [V/V]
(1)
7.2 Functional Block Diagram
RSHUNT
COMP1
COMP2
DRV2
Fluxgate Sensor Front-End
Compensation
Coil
Integrator
Fluxgate
Sensor
DRV1
AINP
AINN
Shunt
Sense
Amplifier
Differential
Driver
VOUT
REFIN
Device Control
OR
ERROR BSEL
DRV425
Voltage Reference
RSEL0
REFOUT
RSEL1
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
17
DRV425
SBOS729 – OCTOBER 2015
www.ti.com
7.3 Feature Description
7.3.1 Fluxgate Sensor Front-End
The following sections describe the functional blocks and features of the integrated fluxgate sensor front-end.
7.3.1.1 Fluxgate Sensor
The fluxgate sensor of the DRV425 is uniquely suited for high-performance magnetic-field sensors because of
the high sensitivity, low noise, and low offset of the sensor. The fluxgate principle relies on repeatedly driving the
sensor in and out of saturation; therefore, the sensor is free of any significant magnetic hysteresis. The feedback
loop accurately drives a compensation current through the integrated compensation coil and drives the magnetic
field at the sensor back to zero. This approach supports excellent gain stability and high linearity of the
measurement.
The DRV425 package is free of any ferromagnetic materials in order to prevent magnetization by external fields
and to obtain accurate and hysteresis-free operation. Select non-magnetizable materials for the printed circuit
board (PCB) and passive components in the direct vicinity of the DRV425; see the Layout Guidelines section for
more details.
The orientation and the sensitivity axis of the fluxgate sensor is indicated by a dashed line on the top of the
package, as shown in Figure 61. Figure 61 also shows the location of the sensor inside the package.
Sensitivity Axis Indication
(Top View)
Sensor Location
(Top View)
Sensor Location
(Side View)
>
0.4 mm ± 0.025 mm
Top
DRV425
TI Date
Code
Bottom
Figure 61. Magnetic Sensitivity Direction of the Integrated Fluxgate Sensor
The sensitivity of the fluxgate sensor is a vector function of its sensitivity axis and the magnetic field orientation.
Figure 62 shows the output of the DRV425 in dependency of the orientation of the device to a constant magnetic
field.
2.65
2.6
VVOUT (V)
2.55
2.5
2.45
2.4
2.35
0
30
60
90 120 150 180 210 240 270 300 330 360
Angle (q)
D063
Figure 62. DRV425 Output vs Magnetic Field Orientation
18
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
DRV425
www.ti.com
SBOS729 – OCTOBER 2015
Feature Description (continued)
7.3.1.2 Bandwidth
The small-signal bandwidth of the DRV425 is determined by the behavior of the compensation loop versus
frequency. The implemented integrator limits the bandwidth of the loop to provide stable response. Use the
digital input pin BSEL to select the bandwidth. For a shunt resistor of 22 Ω and BSEL = 0, the bandwidth is
32 kHz; for BSEL = 1, the bandwidth is 47 kHz.
Bandwidth can be reduced by increasing the value of the shunt resistor because the shunt resistor and the
compensation coil resistance form a voltage divider. The reduced bandwidth (BW) can be calculated using
Equation 2:
RCOIL 22 :
122 :
u BW22 :
u BW22 :
BW
RCOIL RSHUNT
100 : RSHUNT
where
•
•
•
RCOIL = internal compensation coil resistance (100 Ω),
RSHUNT = external shunt resistance, and
BW22Ω = sensor bandwidth with RSHUNT = 22 Ω (depending on the BSEL setting)
(2)
The bandwidth for a given shunt resistor value can also be calculated using the DRV425 System Parameter
Calculator, SLOC331. For large magnetic fields (B > 500 μT), the effective bandwidth of the sensor is limited by
fluxgate saturation effects. For a magnetic signal with a 2-mT amplitude, the large-signal bandwidth is 10 kHz
with BSEL = 0 or 15 kHz with BSEL = 1.
Although the analog output responds slowly to large fields, a magnetic field with a magnitude of 1.6 mT (or
higher) beyond the measurement range of the DRV425 triggers the ERROR pin within 4 µs to 6 µs. See the
Magnetic Field Range, Overrange Indicator, and Error Flag section for more details.
7.3.1.3 Differential Driver for the Internal Compensation Coil
The differential compensation coil driver provides the current for the internal compensation coil at the DRV1 and
DRV2 pins. The driver is capable of sourcing up to ±250 mA with a 5-V supply or up to ±150 mA in 3.3-V mode.
The current capability is not internally limited. The actual value of the compensation coil current depends on the
magnetic field strength and is limited by the sum of the resistance of the internal compensation coil and the
external shunt resistor value. The internal compensation coil resistance depends on temperature (see Figure 17)
and must be taken into account when dimensioning the system. Select the value of the shunt resistor to avoid
OR pin trip levels in normal operation.
The common-mode voltage of the compensation coil driver outputs is set by the RSEL pins (see the Voltage
Reference section). Thus, the common-mode voltage of the shunt-sense amplifier is matched if the internal
reference is used.
Consider the polarity of the compensation coil connection to the output of the compensation coil driver. If the
polarity is incorrect, then the driver output drives to the power-supply rails, even at low primary-current levels. In
this case, interchange the connection of the DRV1 and DRV2 pins to the compensation coil.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
19
DRV425
SBOS729 – OCTOBER 2015
www.ti.com
Feature Description (continued)
7.3.1.4 Magnetic Field Range, Overrange Indicator, and Error Flag
The measurement range of the DRV425 is determined by the amount of current driven into the compensation coil
and the output voltage range of the shunt-sense amplifier. The maximum compensation current is limited by the
supply voltage and the series resistance of the compensation coil and the shunt.
The magnetic field range is adjusted with the external shunt resistor. The DRV425 System Parameter Calculator,
SLOC331 provides the maximum shunt resistor values depending on the supply voltage (VDD) and the selected
reference voltage (VREFIN) for various magnetic field ranges.
For proper operation at a maximum field (BMAX), choose a shunt resistor (RSHUNT) using Equation 3
RSHUNT d
min VDD VREFIN ,VREFIN 0.085 V
BMAX u 12.2 A/T u 4 V/V
where
•
•
•
VDD = minimum supply voltage of the DRV425 (V),
VREFIN = common-mode voltage of the shunt-sense amplifier (V), and
BMAX = desired magnetic field range (T)
(3)
Alternatively, to adjust the output voltage of the DRV425 for a desired maximum voltage (VVOUTMAX), use
Equation 4:
VVOUTMAX VREFIN
RSHUNT d
BMAX u 12.2 A/T u 4 V/V
where
•
•
VVOUTMAX = desired maximum output voltage at VOUT pin (V), and
BMAX = desired magnetic field range (T)
(4)
To avoid railing of the compensation coil driver, assure that Equation 5 is fulfilled:
BMAX u (RCOIL RSHUNT ) u 12.2A / T
0.1V d min VDD VREFIN ,VREFIN
2
where
•
•
•
•
BMAX = desired magnetic field range (T),
RCOIL = compensation coil resistance (Ω),
VDD = minimum supply voltage of the DRV425 (V), and
VREFIN = selected internal reference voltage value (V)
(5)
The DRV425 System Parameter Calculator, SLOC331 is designed to assist with selecting the system
parameters.
The DRV425 offers two diagnostic output pins to detect large fields that exceed the measurement range of the
sensor: the overrange indicator (OR) and the ERROR flag.
In normal operation, the DRV425 sensor feedback loop compensates the magnetic field inside the fluxgate to
zero. Therefore, a large field inside the fluxgate indicates that the feedback loop is not properly working and the
sensor output is invalid. To detect this condition, the ERROR pin is pulled low if the internal field exceeds 1.6
mT. The ERROR output is suppressed for 4 µs to 6 µs to prevent an undesired reaction to transients or noise.
For static and slowly varying ambient fields, the ERROR pin triggers when the ambient field exceeds the sensor
measurement range by more than 1.6 mT. For dynamic magnetic fields that exceed the sensor bandwidth as
specified in the Specifications section, the feedback loop response is too slow to accurately compensate the
internal field to zero. Therefore, high-frequency fields can trigger the ERROR pin, even if the ambient field does
not exceed the measurement range by 1.6 mT.
In addition, the low-active overrange pin (OR) indicates railing of the output of the shunt-sense amplifier. The OR
output is suppressed for 2.5 µs to 3.5 µs to prevent an undesired reaction to transients or noise. The OR pin trip
level refers to the output voltage value of the shunt-sense amplifier as specified in the Specifications section. Use
Equation 3 and Equation 4 to adjust the OR pin behavior to the specific system-level requirements.
20
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
DRV425
www.ti.com
SBOS729 – OCTOBER 2015
Feature Description (continued)
Both the ERROR and OR pins are open-drain outputs that require an external pullup resistor. Connect both pins
together with a single pullup resistor to provide a single diagnostic flag, if desired.
Based on the DRV425 System Parameter Calculator, SLOC331, for a design for a ±2-mT magnetic field input
range with a supply of 5 V (±5%), a shunt resistor value of 22 Ω is selected and Figure 63 shows the status of
the diagnostic flags in the resulting three operation ranges.
Sensor Saturation: B > 3.6 mT
(OR = 0, ERROR = 0)
4
Magnetic Field B (mT)
3
Magnetic Overrange: 2 mT < %”3.6 mT
(OR = 0, ERROR = 1)
2
1
0
Designated Operating Range: 2 P7”%”2 mT
(OR = 1, ERROR = 1)
1
2
3
Magnetic Overrange: 3.6 P7”%< 2 mT
(OR = 0, ERROR = 1)
4
Sensor Saturation: B < 3.6 mT
(OR = 0, ERROR = 0)
Figure 63. Magnetic Field Range of the DRV421 (VDD = 5 V and RSHUNT = 22 Ω)
With the proper RSHUNT value, the differential amplifier output rails and activates the overrange flag (OR = 0)
when the magnetic field exceeds the designated operating range. For fields that exceed the measurement range
of the DRV425 by ≥ 1.6 mT, the fluxgate is permanently saturated and the ERROR pin is pulled low. In this
condition, the fluxgate sensor does not provide a valid output value and, therefore, the output VOUT of the
DRV425 must be ignored. In applications where the ERROR pin cannot be separately monitored, combining the
VOUT and ERROR outputs is recommended (as shown in Figure 64) to indicate a magnetic field outside of the
sensor range by pulling the output of the DRV425 to ground.
BSEL
RSEL0
RSEL1
5V
1 k:
VOUT
REFIN
REFOUT
OR
ERROR
VDD
VDD
GND
Device
GND
RSHUNT
DRV2
DRV1
AINP
AINN
COMP1
COMP2
1 µF
1 µF
5V
Figure 64. Field Overrange Detection Using a Combined VOUT and ERROR Pin
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
21
DRV425
SBOS729 – OCTOBER 2015
www.ti.com
Feature Description (continued)
7.3.2 Shunt-Sense Amplifier
The compensation coil current creates a voltage drop across the external shunt resistor, RSHUNT. The internal
differential amplifier senses this voltage drop. This differential amplifier offers wide bandwidth and a high slew
rate. Excellent dc stability and accuracy result from a chopping technique. The voltage gain is 4 V/V, set by
precisely-matched and thermally-stable internal resistors.
Both the AINN and AINP differential amplifier inputs are connected to the external shunt resistor. This shunt
resistor, in series with the internal 10-kΩ input resistors of the shunt sense amplifier, causes an additional gain
error. Therefore, for best common-mode rejection performance, place a dummy shunt resistor (R5) with a value
higher than the shunt resistor in series with the REFIN pin to restore the matching of both resistor dividers, as
shown in Figure 65.
Device
DRV2
DRV1
AINP
R1
10 k R2
40 k _
RSHUNT
Shunt-Sense
Amplifier
Optional
RF
500 VOUT
ADC
CF
10 nF
+
AINN
R3
10 k R4
40 k REFIN
REFIN (Compensated)
R5
(Dummy Shunt)
ICOMP1
ICOMP2
Figure 65. Internal Difference Amplifier with an Example of a Decoupling Filter
For an overall gain of 4 V/V, calculate the value of R5 using Equation 6:
R 4 + R5
R
4= 2 =
R1
RSHUNT + R3
where:
•
•
R2 / R1 = R4 / R3 = 4,
R5 = RSHUNT × 4
(6)
If the input signal is large, the amplifier output drives close to the supply rails. The amplifier output is able to drive
the input of a successive approximation register (SAR) analog-to-digital converter (ADC). For best performance,
add an RC low-pass filter stage between the shunt-sense amplifier output and the ADC input. This filter limits the
noise bandwidth and decouples the high-frequency sampling noise of the ADC input from the amplifier output.
For filter resistor RF and filter capacitor CF values, see the specific converter recommendations in the respective
product data sheet.
The shunt-sense amplifier output drives 100 pF directly and shows a 50% overshoot with a 1-nF capacitance.
Filter resistor RF extends the capacitive load range. Note that with an RF of only 20 Ω, the load capacitor must be
either less than 1 nF or more than 33 nF to avoid overshoot; with an RF of 50 Ω, this transient area is avoided.
22
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
DRV425
www.ti.com
SBOS729 – OCTOBER 2015
Feature Description (continued)
Reference input REFIN is the common-mode voltage node for the output signal VOUT. Use the internal voltage
reference of the DRV425 by connecting the REFIN pin to the reference output REFOUT. To avoid mismatch
errors, use the same reference voltage for REFIN and the ADC. Alternatively, use an ADC with a pseudodifferential input, with the positive input of the ADC connected to VOUT and the negative input connected to
REFIN of the DRV425.
7.3.3 Voltage Reference
The internal precision voltage reference circuit offers low-drift performance at the REFOUT output pin and is
used for internal biasing. The reference output is intended to be the common-mode voltage of the output (the
VOUT pin) to provide a bipolar signal swing. This low-impedance output tolerates sink and source currents of
±5 mA. However, fast load transients can generate ringing on this line. A small series resistor of a few ohms
improves the response, particularly for capacitive loads equal to or greater than 1 μF.
Adjust the value of the voltage reference output to the power supply of the DRV425 using mode selection pins
RSEL0 and RSEL1, as shown in Table 1.
Table 1. Reference Output Voltage Selection
MODE
RSEL1
RSEL0
VREFOUT = 2.5 V
0
0
Use with a sensor module supply of 5 V
DESCRIPTION
VREFOUT = 1.65 V
0
1
Use with a sensor module supply of 3.3 V
Ratiometric output
1
x
Provides an output centered on VDD / 2
In ratiometric output mode, an internal resistor divider divides the power-supply voltage by a factor of two.
7.3.4 Low-Power Operation of the DRV425
In applications with low-bandwidth or low sample-rate requirements, the average power dissipation of the
DRV425 can be significantly reduced by powering the device down between measurements. The DRV425
requires 300 μs to fully settle the analog output VOUT, as shown in Figure 66. To minimize power dissipation,
the device can be powered down immediately after acquiring the sample by the ADC.
startup
VDD
VOUT
Settling time:
300 µs
Figure 66. Settling Time of the DRV425 Output VOUT
7.4 Device Functional Modes
The DRV425 is operational when the power supply VDD is applied, as specified in the Specifications section.
The DRV425 has no additional functional modes.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
23
DRV425
SBOS729 – OCTOBER 2015
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The DRV425 is a high-sensitivity and high-performance magnetic-field sensor. The analog output of the DRV425
can be processed by a 12- to 16-bit analog to digital converter (ADC). The following sections show examples of
DRV425-based applications.
8.2 Typical Applications
8.2.1 Linear Position Sensing
The high sensitivity of the fluxgate sensor, combined with the high linearity of the compensation loop and low
noise of the DRV425, make the device suitable for high-performance linear-position sense applications. A typical
schematic of such a 5-V application using an internal 2.5-V reference is shown in Figure 67.
BSEL
RSEL0
RSEL1
5V
Device
VOUT
REFIN
REFOUT
OR
ERROR
VDD
VDD
10 k:
1 µF
ADC
GPIO0
GPIO1
GND
DRV2
DRV1
AINP
AINN
COMP1
COMP2
GND
RSHUNT
MCU
1 µF
10 k:
5V
Figure 67. Simplified Schematic of a DRV425-Based Linear-Position Sensing Application
8.2.1.1 Design Requirements
For the example shown in Figure 67, use the parameters listed in Table 2 as a starting point of the design.
Table 2. Design Parameters
DESIGN PARAMETER
Magnetic field range
VDD = 5 V: ±2 mT (max)
VDD = 3.3 V: ±1.3 mT (max)
Supply voltage, VDD
3.0 V to 5.5 V
Reference voltage, VREFIN
Shunt resistor, RSHUNT
24
EXAMPLE VALUE
Range: GND to VDD
If an internal reference is used: 2.5 V, 1.65 V, or VDD / 2
Depends on the desired magnetic field range, reference, and supply voltage; see the
DRV425 System Parameter Calculator, SLOC331 for details.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
DRV425
www.ti.com
SBOS729 – OCTOBER 2015
8.2.1.2 Detailed Design Procedure
Use the following procedure to design a solution for a linear-position sensor based on the DRV425:
•
•
•
•
•
Select the proper supply voltage VDD to support the desired magnetic field range (see Table 2 for reference).
Select the proper reference voltage VREFIN to support the desired magnetic field range and to match the input
voltage specifications of the desired ADC.
Use the DRV425 System Parameter Calculator, SLOC331 (RangeCalculator tab) to select the proper shunt
resistor value of RSHUNT.
The sensitivity drift performance of a DRV425-based linear position sensor is dominated by the temperature
coefficient of the external shunt resistor. Select a low-drift shunt resistor for best sensor performance.
Use the DRV425 System Parameter Calculator, SLOC331 (Problems Detected Table in DRV425 System
Parameters tab) to verify the system response.
The amplitude of the magnetic field is a function of distance to and the shape of the magnet, as shown in
Figure 69. If the magnetic field to be measured exceeds 3.6 mT, see the datasheet of the magnet to calculate
the appropriate minimum distance to the DRV425 to avoid saturating the fluxgate sensor.
The high sensitivity of the DRV425 may require shielding of the sensing area to avoid influence of undesired
magnetic field sources (such as the earth magnetic field). Alternatively, an additional DRV425 can be used to
perform difference measurement to cancel the influence of a static magnetic field source, as shown in Figure 68.
Figure 70 shows the differential voltage generated by two DRV425 devices in such a circuit.
DRV425-2
DRV425-1
Direction of Linear
Movement
>
>
REFOUT
REFIN
VOUT
REFOUT
REFIN
VOUT
ADC
Figure 68. Differential Linear-Position Sensing Using Two DRV425 Devices
2.6
2.4
2.2
2
1.8
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0
VVOUTDRV425-1 - VVOUTDRV425-2 (mV)
VVOUT (V)
8.2.1.3 Application Curves
0
50
100
150
200 250 300
Distance (mm)
350
400
450
500
1500
1400
1300
1200
1100
1000
900
800
700
600
500
400
300
200
100
0
0
D064
Figure 69. Analog Output Voltage of the DRV425 vs
Distance to the Magnet
20
40
60
80 100 120
Distance (mm)
140
160
180
200
D065
Figure 70. Difference Between Two DRV425 Outputs vs
Distance to the Magnet
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
25
DRV425
SBOS729 – OCTOBER 2015
www.ti.com
8.2.2 Current Sensing in Busbars
In existing applications that use busbars for power distribution, closed-loop current modules are usually used to
accurately measure and control the current. These modules are usually bulky because of the required large
magnetic core. Additionally, because the compensation current generated inside the module is proportional to the
usually high busbar current, the power dissipation of this solution is usually as high as several watts.
Figure 71 shows an alternative approach with two DRV425 devices. If a hole is drilled in the middle of the
busbar, the current is split in two equal parts that generate magnetic field gradients with opposite directions
inside the hole. These magnetic fields are termed BR and BL in Figure 72. The opposite fields cancel each other
out in the middle of the hole. The high sensitivity and linearity of two DRV425 devices positioned at the same
distance from the middle of the hole allow the small opposite fields to be sensed and the current measured with
high-accuracy levels. The differential measurement rejects outside fields that generate a common-mode error
that is subtracted at the output.
Busbar
(Top View)
I/2
Hole
DRV425-1
I
I
DRV425-2
PCB
I/2
Figure 71. DRV425-Based Busbar Current Sensing
I
Axis of
cross-section
I/2
I/2
Cross-section
PCB
DRV425 - 1
BR
I/2
I/2
Y-Axis
BL
DRV425 - 2
Figure 72. Magnetic Field Distribution Inside a Busbar Hole
26
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
DRV425
www.ti.com
SBOS729 – OCTOBER 2015
8.2.2.1 Design Requirements
In order to measure the field gradient in the busbar, two DRV425 sensors are placed inside the hole at a welldefined distance by mounting them on opposite sides of a PCB that is inserted in the hole. The measurement
range and resolution of this solution depends on the following factors:
• Busbar geometry: a wider busbar means a larger measurement range and lower resolution.
• Size of the hole: a larger diameter means a larger measurement range and lower resolution.
• Distance between the two DRV425 sensors: a smaller distance increases the measurement range and
resolution.
Each of these factors can be optimized to create the desired measurement range for a particular application.
Measurement ranges of ±250 A to ±1500 A are achievable with this approach. Larger currents are supported
with large busbar structures and minimized distance between the two DRV425 sensors. Use the parameters
listed in Table 3 as a starting point of the design.
Table 3. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
Current range
Up to ±1500 A
Supply voltage, VDD
3.0 V to 5.5 V
Reference voltage, VREFIN
VDD / 2
8.2.2.2 Detailed Design Procedure
Figure 73 shows the schematic diagram of a differential gradient field measurement circuit.
BSEL
RSEL0
RSEL1
1 µF
GND
VDD
VDD
1 µF
DRV2
DRV1
AINP
AINN
COMP1
COMP2
VCM
U2
DRV425
1 µF
VDD
R1
5.1 :
VOUT
REFIN
REFOUT
OR
ERROR
VDIFF
GND
VOUT
REFIN
REFOUT
OR
ERROR
GND
U1
DRV425
GND
DRV2
DRV1
AINP
AINN
COMP1
COMP2
VDD
VDD
BSEL
RSEL0
RSEL1
VDD
1 µF
VDD
R2
5.1 :
VDD
10 k:
R3
10 :
1 µF
+
U3
OPA320
VREF
10 k:
±
Figure 73. Schematic of a DRV425-Based Busbar Current-Sensing Circuit
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
27
DRV425
SBOS729 – OCTOBER 2015
www.ti.com
In Figure 73, the feedback loops of both DRV425 sensors are combined to directly produce a differential output
VDIFF that is proportional to the sensed magnetic field difference inside the busbar hole. Both compensation coils
are connected in series and are driven from a single side of the compensation coil driver (the DRV1 pins of each
DRV425). Therefore, both driver stages ensure that a current proportional to the magnetic fields BR and BL is
driven through the respective compensation coil. The difference in current through both compensation coils, and
thus the difference field between the sensors, flows through resistor R3 and is sensed by the shunt-sense
amplifier of U2. The current proportional to the common-mode field inside the busbar hole flows through R1 and
R2 and is sensed by the shunt-sense amplifier of U1.
Use the output VCM to verify that the sensors are correctly positioned in the busbar hole with the following steps:
1. Measure VCM with no current flow through the busbar and the PCB in the middle of the busbar hole. This
value is the offset voltage VOFFSET. The value of VOFFSET only depends on stray fields and varies little with the
absolute position of the sensors.
2. Apply current through the busbar and move the PCB along the y-axis in the busbar hole, as shown in
Figure 72. The PCB is in the center of the hole if VCM = VOFFSET.
The sensitivity drift performance of the circuit shown in Figure 73 is dominated by the temperature coefficient of
the external resistors R1, R2, and R3. Select low-drift resistors for best sensor performance. For overall system
error calculation, also consider the affect of thermal expansion on the PCB and busbar.
The internal voltage reference of the DRV425 cannot be used in this application because of its limited driver
capability. The OPA320 (U3) is a low-noise operational amplifier with a short-circuit current capability of ±65 mA
and is used to support the required compensation current.
The advantage of this solution is its simplicity: the currents are subtracted by the two DRV425 devices without
additional components. The series connection of the compensation coils halves the voltage swing and reduces
the measurement range of the sensors also by 50%. If a larger sensing range is required, operate the two
sensors independently and use a differential amplifier or ADC to subtract both voltage outputs (VOUT).
Use the ERROR outputs for fast overcurrent detection on the system level.
8.2.2.3 Application Curves
Figure 74 and Figure 75 show the measurement results on a 16-mm wide and 6-mm thick copper busbar with a
12-mm hole diameter using the circuit shown in Figure 73. The two DRV425 devices are placed at a distance of
1 mm from each other on opposite sides of the PCB. The measurement range is ±500 A; measurement results
are limited by test setup. Independent operation of the two DRV425 sensors increases the measurement range
to ±1000 A with the same busbar geometry.
400
0.5
350
0.4
0.3
Linearity Error (%FS)
VDIFF - VREF (mV)
300
250
200
150
100
0.2
0.1
0
-0.1
-0.2
-0.3
50
-0.4
0
-0.5
0
20
40
60
80 100 120 140
Busbar Current (A)
160
180
0
20
D066
Figure 74. Analog Output Voltage vs
Busbar Current
28
200
40
60
80 100 120 140
Busbar Current (A)
160
180
200
D067
Figure 75. Linearity Error vs Busbar Current
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
DRV425
www.ti.com
SBOS729 – OCTOBER 2015
9 Power-Supply Recommendations
9.1 Power-Supply Decoupling
Decouple both VDD pins of the DRV425 with 1-µF, X7R-type ceramic capacitors to the adjacent GND pin as
illustrated in Figure 76. For best performance, place both decoupling capacitors as close to the related powersupply pins as possible. Connect these capacitors to the power-supply source in a way that allows the current to
flow through the pads of the decoupling capacitors.
9.2 Power-On Start-Up and Brownout
Power-on is detected when the supply voltage exceeds 2.4 V at the VDD pin. At this point, the DRV425 initiates
the following start-up sequence:
1. Digital logic starts up and waits for 26 μs for the supply to settle.
2. The fluxgate sensor powers up.
3. The compensation loop is active 70 μs after the supply voltage exceeds 2.4 V.
During this startup sequence, the DRV1 and DRV2 outputs are pulled low to prevent undesired signals on the
compensation coil and the ERROR pin is asserted low.
The DRV425 tests for low supply voltages with a brownout voltage level of 2.4 V. Use a power-supply source
capable of supporting large current pulses driven by the DRV425, and low-ESR bypass capacitors for a stable
supply voltage in the system. A supply drop below 2.4 V that lasts longer than 20 μs generates a power-on reset;
the device ignores shorter voltage drops. A voltage drop on the VDD pin to below 1.8 V immediately initiates a
power-on reset. After the power supply returns to 2.4 V, the device initiates a start-up cycle.
9.3 Power Dissipation
The thermally-enhanced, PowerPAD, WQFN package reduces the thermal impedance from junction to case.
This package has a downset lead frame that the die is mounted to. The lead frame has an exposed thermal pad
(PowerPAD) on the underside of the package, and provides a good thermal path for heat dissipation.
The power dissipation on both linear outputs DRV1 and DRV2 is calculated with Equation 7:
PD(DRV) = IDRV × (VDRV – VSUPPLY)
where
•
•
•
IDRV = supply current as shown in Figure 59,
VDRV = voltage potential on the DRV1 or DRV2 output pin, and
VSUPPLY = voltage potential closer to VDRV: VDD or GND
(7)
9.3.1 Thermal Pad
Packages with an exposed thermal pad are specifically designed to provide excellent power dissipation, but
board layout greatly influences the overall heat dissipation. Technical details are described in application report
PowerPad Thermally Enhanced Package, SLMA002, available for download at www.ti.com.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
29
DRV425
SBOS729 – OCTOBER 2015
www.ti.com
10 Layout
10.1 Layout Guidelines
The unique, integrated fluxgate of the DRV425 has a very high sensitivity to enable designing a closed-loop
magnetic-field sensor with best-in-class precision and linearity. Observe proper PCB layout techniques because
any current-conducting wire in the direct vicinity of the DRV425 generates a magnetic field that can distort
measurements. Common passive components and some PCB plating materials contain ferromagnetic materials
that are magnetizable. For best performance, use the following layout guidelines:
• Route current-conducting wires in pairs: route a wire with an incoming supply current next to, or on top of, its
return current path. The opposite magnetic field polarity of these connections cancel each other. To facilitate
this layout approach, the DRV425 positive and negative supply pins are located next to each other.
• Route the compensation coil connections close to each other as a pair to reduce coupling effects.
• Minimize the length of the compensation coil connections between the DRV1/2 and COMP1/2 pins.
• Route currents parallel to the fluxgate sensor sensitivity axis as illustrated in Figure 76. As a result, magnetic
fields are perpendicular to the fluxgate sensitivity and have limited affect.
• Vertical current flow (for example, through vias) generates a field in the fluxgate-sensitive direction. Minimize
the number of vias in the vicinity of the DRV425.
• Use nonmagnetic passive components (for example, decoupling capacitors and the shunt resistor) to prevent
magnetizing effects near the DRV425.
• Do not use PCB trace finishes with nickel-gold plating because of the potential for magnetization.
• Connect all GND pins to a local ground plane.
Ferrite beads in series to the power-supply connection reduce interaction with other circuits powered from the
same supply voltage source. However, to prevent influence of the magnetic fields if ferrite beads are used, do
not place them next to the DRV425.
The reference output (the REFOUT pin) refers to GND. Use a low-impedance and star-type connection to reduce
the driver current and the fluxgate sensor current modulating the voltage drop on the ground track. The REFOUT
and VOUT outputs are able to drive some capacitive load, but avoid large direct capacitive loading because of
increased internal pulse currents. Given the wide bandwidth of the shunt-sense amplifier, isolate large capacitive
loads with a small series resistor.
Solder the exposed PowerPAD on the bottom of the package to the ground layer because the PowerPAD is
internally connected to the substrate that must be connected to the most-negative potential.
Figure 76 illustrates a generic layout example that highlights the placement of components that are critical to the
DRV425 performance. For specific layout examples, see the DRV425EVM Users Guide, SLOU410.
30
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
DRV425
www.ti.com
SBOS729 – OCTOBER 2015
10.2 Layout Example
Fluxgate sensor sensitivity axis
Keep this area free of components
creating magnetic fields.
COMP1
COMP2
GND
ERROR
GND
To MCU
To MCU
BSEL
OR
RSEL1
AINN
RSEL0
AINP
RSHUNT
1206
LEGEND
VDD
VDD
GND
X7R
0603
1 µF
X7R
0603
DRV2
GND
REFIN
1 µF
DRV1
VOUT
REFOUT
To ADC
Top Layer:
Copper Pour and Traces
Via to Ground Plane
Via to Supply Plane
Figure 76. Generic Layout Example (Top View)
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
31
DRV425
SBOS729 – OCTOBER 2015
www.ti.com
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
OPA320 Data Sheet, SBOS513
DRV425EVM Users Guide, SLOU410
DRV425 System Parameter Calculator, SLOC331
Application Report PowerPad Thermally Enhanced Package, SLMA002
11.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.3 Trademarks
PowerPAD, E2E are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
11.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
32
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: DRV425
PACKAGE OPTION ADDENDUM
www.ti.com
20-Nov-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
DRV425RTJR
ACTIVE
QFN
RTJ
20
3000
Green (RoHS
& no Sb/Br)
CU
Level-3-260C-168 HR
-40 to 125
----->
DRV425
DRV425RTJT
ACTIVE
QFN
RTJ
20
250
Green (RoHS
& no Sb/Br)
CU
Level-3-260C-168 HR
-40 to 125
----->
DRV425
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
20-Nov-2015
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
Similar pages