STMicroelectronics LD39030SJ12R Digital still camera Datasheet

LD39030SJ
300 mA low quiescent current
soft-start, low noise voltage regulator
Datasheet - production data
Applications
• Mobile phones
• Personal digital assistants (PDAs)
• Cordless phones and similar battery-powered
systems
• Digital still cameras.
Description
Flip-chip 4
Features
• Input voltage from 1.5 to 5.5 V
• Ultra low dropout voltage (200 mV typ. at 300
mA load)
• Very low quiescent current (20 μA typ. at no
load, 40 μA typ. at 300 mA load, 1 μA max. in
off mode)
• Very low noise (30 μVRMS from 1 kHz to 100
kHz at VOUT = 1.8 V)
The LD39030SJ is a low noise voltage regulator
that provides 300 mA maximum current from an
input voltage in the 1.5 V to 5.5 V range, with a
typical dropout voltage of 200 mV. It is stabilized
with a ceramic capacitor on the output. The ultra
low drop voltage, low quiescent current, and low
noise features make it suitable for low power
battery-powered applications. Power supply
rejection is typically 62 dB at low frequencies and
starts to roll off at 10 kHz. An enable logic control
function puts the LD39030SJ in shutdown mode
allowing a total current consumption lower than
1 μA. The device also includes a short-circuit
constant current limiting and thermal protection.
• Output voltage tolerance: ± 2.0 % @ 25 °C
Table 1. Device summary
• 300 mA guaranteed output current
Order codes
Output voltages
• Wide range of output voltages available on
request: 0.8 V to 4.5 V with 100 mV step
LD39030SJ10R
1V
• Logic-controlled electronic shutdown
LD39030SJ12R
1.2 V
• Compatible with ceramic capacitor COUT = 1 μF
LD39030SJ126R
1.26 V
• Internal current and thermal limit
LD39030SJ28R
2.8 V
• Flip-chip 4 bumps 0.8 x 0.8 mm pitch 0.4 mm
LD39030SJ285R
2.85 V
• Internal soft-start (typ. 100 μs)
LD39030SJ33R
3.3 V
• Temperature range: - 40 °C to 125 °C
February 2014
This is information on a product in full production.
DocID18103 Rev 5
1/18
www.st.com
Contents
LD39030SJ
Contents
1
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3
Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6
Soft-start function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7
Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
9
Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
10
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2/18
DocID18103 Rev 5
LD39030SJ
1
Block diagram
Block diagram
Figure 1. Block diagram
OUT
IN
BandGap
1.22 V
R1
Trimming
Thermal
Protection
R2
Enable
EN
GND
DocID18103 Rev 5
3/18
18
Pin configuration
2
LD39030SJ
Pin configuration
Figure 2. Pin connection (top view)
Table 2. Pin description
4/18
Pin n°
Symbol
A2
EN
A1
GND
B2
IN
B1
OUT
Function
Enable pin logic input: low = shutdown, high = active
Common ground
Input voltage of the LDO
Output voltage
DocID18103 Rev 5
LD39030SJ
3
Typical application
Typical application
Figure 3. Typical application circuit
VIN
IN
1 μF
VEN
VOUT
OUT
1 μF
EN
Load
GND
DocID18103 Rev 5
5/18
18
Maximum ratings
4
LD39030SJ
Maximum ratings
Table 3. Absolute maximum ratings
Symbol
VIN
Parameter
DC input voltage
Value
Unit
- 0.3 to 6
V
VOUT
DC output voltage
- 0.3 to VIN + 0.3
V
VEN
Enable input voltage
- 0.3 to VIN + 0.3
V
IOUT
Output current
Internally limited
mA
Power dissipation
Internally limited
mW
PD
TSTG
Storage temperature range
- 65 to 150
°C
TOP
Operating junction temperature range
- 40 to 125
°C
Note:
Absolute maximum ratings are those values beyond which damage to the device may occur.
Functional operation under these conditions is not implied. All values are referred to GND.
Table 4. Thermal data
Symbol
RthJA
6/18
Parameter
Thermal resistance junction-ambient
DocID18103 Rev 5
Value
Unit
180
°C/W
LD39030SJ
5
Electrical characteristics
Electrical characteristics
TJ = 25 °C, VIN = VOUT(NOM) + 1 V, CIN = COUT = 1 μF, IOUT = 1 mA, VEN = VIN, unless
otherwise specified.
Table 5. Electrical characteristics
Symbol
Parameter
VIN
Operating input voltage
Test conditions
(1)
Min.
Typ.
1.5
Turn-on threshold
1.45
Max.
Unit
5.5
V
1.48
V
VUVLO
Turn-off threshold
VOUT
VOUT accuracy
1.30
1.35
VOUT >1.5 V, IOUT=1 mA, TJ=25 °C
-2.0
2.0
%
VOUT >1.5 V, IOUT=1 mA,
-40 °C<TJ<125 °C
-3.0
3.0
%
VOUT ≤ 1.5 V, IOUT=1 mA
±10
mV
VOUT ≤ 1.5 V, IOUT=1 mA,
-40 °C<TJ<125 °C
±30
mV
0.01
%/V
10
mVpp
0.002
%/mA
mVpp
ΔVOUT
Static line regulation
VOUT +1 V ≤ VIN ≤ 5.5 V, IOUT=1 mA
ΔVOUT
Transient line
regulation (2)
ΔVIN=+500 mV, IOUT=1 mA,
TR=TF=5 μs
ΔVOUT
Static load regulation
IOUT=1 mA to 300 mA
ΔVOUT
Transient load
regulation (2)
IOUT=1 mA to 300 mA, TR=TF=5 μs
40
VDROP
Dropout voltage (3)
IOUT=300 mA, VOUT>1.5 V
-40 °C<TJ<125 °C
200
Output noise voltage
10 Hz to 100 kHz, IOUT=10 mA
30
VIN=VOUTNOM+1 V+/-VRIPPLE
VRIPPLE=0.1 V Freq.=1 kHz
IOUT=10 mA
62
eN
SVR
Supply voltage
rejection VOUT = 1.2 V
Quiescent current
62
IOUT=0 mA
20
IOUT=0 to 300 mA
μVRMS
/V
40
μA
85
VIN input current in OFF MODE:
VEN=GND
Short-circuit current
mV
50
IOUT=0 to 300 mA, -40 °C<TJ<125 °C
ISC
300
dB
VIN=VOUTNOM+0.5 V+/-VRIPPLE
VRIPPLE=0.1 V Freq.=10 kHz
IOUT=10 mA
IOUT=0 mA, -40 °C<TJ<125 °C
IQ
mV
RL=0
0.001
400
DocID18103 Rev 5
1
mA
7/18
18
Electrical characteristics
LD39030SJ
Table 5. Electrical characteristics (continued) (1)
Symbol
Parameter
Test conditions
Enable input logic low
VIN=1.5 V to 5.5 V, -40 °C<TJ<125 °C
Enable input logic high
VIN=1.5 V to 5.5 V, -40 °C<TJ<125 °C
Min.
Typ.
Max.
0.4
VEN
IEN
TON
V
0.9
Enable pin input current VSHDN=VIN
Turn-on time
0.1
(4)
100
100
Thermal shutdown
160
Hysteresis
20
nA
μs
°C
TSHDN
COUT
Unit
Output capacitor
Capacitance (see Section 7: Typical
performance characteristics)
1
22
μF
1. For VOUT(NOM) < 1.2 V, VIN = 1.5 V.
2. All transient values are guaranteed by design, not production tested.
3. Dropout voltage is the input-to-output voltage difference at which the output voltage is 100 mV below its nominal value. This
specification does not apply for output voltages below 1.5 V.
4. Turn-on time is time measured between the enable input just exceeding VEN high value and the output voltage just
reaching 95 % of its nominal value.
8/18
DocID18103 Rev 5
LD39030SJ
6
Soft-start function
Soft-start function
The LD39030S has an internal soft-start circuit. By increasing the startup time up to 100 μs,
without the need of any external soft-start capacitor, this feature is able to reduce the
regulator inrush current to 1/3 of the original value.
Figure 4. Soft-start function
V
EN
V
IN
V
I
OUT
IN
VIN = 1.8 V, VEN = 1.8 V, CIN = 1 μF, COUT = 1 μF.
DocID18103 Rev 5
9/18
18
Typical performance characteristics
7
LD39030SJ
Typical performance characteristics
CIN = COUT = 1 μF, VEN to VIN.
Figure 5. Output voltage vs. temperature
Figure 6. Output voltage vs. input voltage
1.3
1.4
CIN = C OUT = 1 μF; VEN to VIN IOUT = 1 mA
VIN = VEN = 2.2 V ; IOUT = 1 mA
125
1.28
1.2
85
1.26
25
VOUT [V]
1.22
VOUT [V]
55
1
1.24
1.2
1.18
0.8
0
1.16
0.6
-25
0.4
-40
1.14
0.2
VOUT = 1.2 V
1.12
VOUT = 1.2 V
0
1.1
0
-75
-50
-25
0
25
50
75
100
125
150
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
175
VIN [V]
T [°C]
Figure 7. Line regulation vs. temperature
Figure 8. Load regulation vs. temperature
0.006
0.05
VIN = 2.2 V; IOUT = from 1 to 300 mA
VIN = from 2.3 V to 5.5 V; IOUT = 1 mA
0.004
Load [%/mA]
0.04
Line [%/V]
0.03
0.02
0.01
0
0.002
0
-0.002
-0.004
VOUT = 1.2 V
VOUT = 1.2 V
-0.01
-0.006
-75
-50
-25
0
25
50
75
100
125
150
175
-75
-50
-25
0
25
50
75
100
125
150
175
T [°C]
T [°C]
Figure 9. Short-circuit current vs. drop voltage
Figure 10. Quiescent current vs. input voltage
0.8
35
IOUT = 1 mA
0.7
30
0.6
25
IQ [μA]
ISC [A]
0.5
0.4
20
15
0.3
10
0.2
CIN = 1 μF (+100 μF electrolytic)
5
0.1
COUT = 1 μF (+10 μF electrolytic)
VOUT = 1.2 V
0
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
0
10/18
1
2
3
VIN [V]
DROP [V]
DocID18103 Rev 5
4
5
6
LD39030SJ
Typical performance characteristics
Figure 11. Enable threshold vs. temperature
Figure 12. Quiescent current vs. temperature
90
1
VIN = 2.2 V; IOUT = 0.3 A
80
0.8
70
0.7
60
IQ [μA]
VEN [V]
VIN = 2.2 V; IOUT = 1 mA
0.9
0.6
0.5
50
40
0.4
30
0.3
20
0.2
10
0.1
VOUT = 1.2 V
VOUT = 1.2 V
0
0
-75
-50
-25
0
25
50
75
100 125
-75
150 175
-50
-25
TEMPERATURE [°C]
0
25
50
75
100
125
150
175
TEMPERATURE [°C]
Figure 13. Supply voltage rejection vs.
temperature (Freq. = 1 kHz)
Figure 14. Supply voltage rejection vs.
frequency (VIN = 1.6 V to 1.8 V)
80
100
IOUT = 10 mA
VIN from 1.6 V to 1.8 V, IOUT = 10 mA
VIN from 2.1 V to 2.3 V, Freq. = 1 kHz
90
75
70
SVR [dB]
SVR [dB]
80
70
65
60
50
40
60
30
20
55
10
VOUT = 1.2 V
VOUT = 1.2 V
0
50
-75
-50
-25
0
25
50
75
100
125
150
0
175
20
40
60
80
100
120
Frequency [kHz]
T [°C]
Figure 15. Supply voltage rejection vs.
temperature (Freq. = 10 kHz)
Figure 16. Supply voltage rejection vs.
frequency (VIN = 2.1 V to 2.3 V)
100
80
VIN from 2.1 V to 2.3 V, IOUT = 10 mA
IOUT = 10 mA
VIN from 1.6 V to 1.8 V, Freq. = 10 kHz
90
75
80
70
SVR [dB]
SVR [dB]
70
65
60
50
40
60
30
20
55
10
VOUT = 1.2 V
VOUT = 1.2 V
50
0
-75
-50
-25
0
25
50
75
100
125
150
175
0
T [°C]
20
40
60
80
100
120
Frequency [kHz]
DocID18103 Rev 5
11/18
18
Typical performance characteristics
LD39030SJ
Figure 17. Line transient
Figure 18. Load transient
VIN
IOUT
VOUT
VOUT
VOUT = 1.2 V
VOUT = 1.2 V
VIN from 2.2 V to 2.7 V, VEN to VIN, IOUT = 1 mA,
COUT = 1 μF, No CIN, tRISE/FALL = 5 μs
VIN = 2.3 V, VEN to VIN, IOUT = from 1 to 300 mA,
CIN = COUT = 1 μF, tRISE/FALL = 5 μs
Figure 19. Enable transient
Figure 20. Startup transient
VEN
VIN
VOUT
VOUT
VOUT = 1.2 V
VOUT = 1.2 V
VIN from 0 to 5.5 V, VEN to VIN, IOUT = 1 mA, COUT = 1 μF,
No CIN, tRISE = 60 μs
VIN = 2.2 V, VEN from 0 to 2 V, IOUT = 1 mA,
CIN = COUT = 1 μF, tRISE = 8 μs
Figure 21. ESR required for stability with
ceramic capacitors
2.25
2
UNSTABLE ZONE
ESR @ 100 kHz [Ω]
1.75
1.5
1.25
1
0.75
STABLE ZONE
0.5
0.25
0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22
COUT [μF] (nominal value)
VIN = VEN = from 2.3 V to 5.5 V, IOUT = from 1 mA to
300 mA, CIN = 1 μF (ceramic)
12/18
DocID18103 Rev 5
LD39030SJ
8
Package mechanical data
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions, and product status are available at: www.st.com.
ECOPACK is an ST registered trademark.
Figure 22. Flip-chip 4 package drawing (dimensions are in mm.)
7504896_M
DocID18103 Rev 5
13/18
18
Package mechanical data
LD39030SJ
Table 6. Flip-chip 4 package mechanical data
mm.
Dim.
Min.
Typ.
Max.
A
0.52
0.56
0.60
A1
0.17
0.20
0.23
A2
0.35
0.36
0.37
b
0.23
0.25
0.29
D
0.758
0.788
0.818
D1
E
0.4
0.758
E1
0.788
0.4
SD
0.18
0.2
0.22
SE
0.18
0.2
0.22
f
0.199
ccc
0.075
Figure 23. Footprint data
14/18
0.818
DocID18103 Rev 5
LD39030SJ
9
Packaging mechanical data
Packaging mechanical data
Figure 24. Flip-chip 4 tape and reel drawing
DocID18103 Rev 5
15/18
18
Packaging mechanical data
LD39030SJ
Table 7. Flip-chip 4 tape and reel mechanical data
mm
Dim.
Min.
Typ.
A
178
C
12.8
D
20.2
N
59
13.2
60
T
16/18
Max.
61
8.4
Ao
0.82
0.87
0.92
Bo
0.82
0.87
0.92
Ko
0.64
0.69
0.74
Po
3.9
4.0
4.1
P
3.9
4.0
4.1
DocID18103 Rev 5
LD39030SJ
10
Revision history
Revision history
Table 8. Document revision history
Date
Revision
14-Oct-2010
1
First release.
10-Jul-2012
2
Added new order code LD39030SJ33R Table 1 on page 1.
Updated Flip-chip 4 mechanical data Table 6 on page 14 and
Figure 22 on page 13.
25-Oct-2012
3
Added new order code LD39030SJ126R Table 1 on page 1.
Document status promoted from preliminary data to production data.
08-Feb-2013
4
Added Table 7: Options available on request on page 15.
5
Part number LD39030SJxx changed to LD39030SJ.
Updated Table 1: Device summary, Section 8: Package mechanical
data and Section 9: Packaging mechanical data.
Minor text changes.
06-Feb-2014
Changes
DocID18103 Rev 5
17/18
18
LD39030SJ
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2014 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
18/18
DocID18103 Rev 5