ETC2 CXL10GP1Z High performance, 1-axis and 3-axis accelerometer Datasheet

CXL-GP Series
RoHS
COMPLIANT
General Purpose ACCELEROMETER
• High Performance, 1-Axis
and 3-Axis Accelerometers
• Small, Low-Cost
• Reliable Packaging with
Screw-Down Mounting
• Factory Calibrated
Applications
• Automotive Testing
• Instrumentation
• Equipment Monitoring
GP Series
The GP Series accelerometers are low
cost, general purpose, linear acceleration and/or vibration sensors available
in ranges of ±4g, ±10g, and ±25g.
Common applications are automotive testing, instrumentation, and
equipment monitoring. The GP Series
sensing element is a silicon micro-machined capacitive beam. The capacitive
beam is held in force balance for full
scale non-linearity of less than 0.2%.
The GP Series offers wide dynamic
r a n g e , h a s e x c e l l e n t f re q u e n c y
response, operates on a single 4.9 to
5.5 VDC power supply, and is easy to
interface to standard data acquisition
systems. The 3-axis version (GP3) can
be specified with an internal regulator
(-R option) for use with a 5.5 to 36 V
unregulated power supply.
The GP Series sensors provide a direct
high-level analog voltage output.
The output requires no external
signal conditioning electronics and
may be directly interfaced to an A/D
or other data acquisition hardware.
Compared to traditional piezoelectric and piezoresistive accelerometer
technologies, the silicon micromachined
sensors offer equivalent performance
at a significantly lower cost.
The GP Series is offered with a standard
5-pin female connector. The highly
flexible, low-mass cable prevents
disruption of the measurement.
Standard Package Dimensions
Phone: 408.964.9700
Fax: 408.854.7702
E-mail: [email protected]
w w w. m e m s i c . c o m
CXL04GP1
CXL04GP1Z
CXL04GP3
CXL10GP1
CXL10GP1Z
CXL10GP3
CXL25GP1
CXL25GP1Z
CXL25GP3
Remarks
Input Range (g)
±4
± 10
± 25
± 5%
Zero g Drift (g)
± 0.1
± 0.3
± 0.5
0°C to 70°C
Sensitivity (mV/g)
500 ± 15
200 ± 5
80 ± 2
Transverse Sensitivity (% Span)
±5
±5
±5
Non-Linearity (% FS)
± 0.2
± 0.2
± 0.2
typical
Pin
Color
Function
Alignment Error (deg)
±2
±2
±2
typical
1
Red
Power In
Noise (mg rms)
10
35
35
typical
2
Black
Ground
Bandwidth (Hz) 1
DC -100
DC -100
DC -100
3
White
X-axis Out
4
Yellow
Y-axis Out
5
Green
Z-axis Out
Specifications
Performance
Environment
Operating Temp. Range (°C)
-40 to +85
-40 to +85
-40 to +85
Operating Temp. Range - AL (°C)
-40 to +105
-40 to +105
-40 to +105
Shock (g)
2000
2000
2000
Supply Voltage (Volts)
+ 4.9 to 5.5
+ 4.9 to 5.5
+ 4.9 to 5.5
Supply Voltage -R option (Volts)
+ 5.5 to 36
+ 5.5 to 36
+ 5.5 to 36
Supply Current (mA)
1/axis
3/axis
3/axis
typical
Zero g Output (Volts)
+ 2.375 ± 0.1
+ 2.375 ± 0.1
+ 2.375 ± 0.1
@25°C
Span Output (Volts)
± 2.0 ± 0.1
± 2.0 ± 0.1
± 2.0 ± 0.1
Output Loading
> 2.0 < 2 nF
> 2.0 < 2 nF
> 2.0 < 2 nF
Size (in)
0.78 x 1.75 x 1.07
0.78 x 1.75 x 1.07
0.78 x 1.75 x 1.07
(cm)
1.98 x 4.45 x 2.72
1.98 x 4.45 x 2.72
1.98 x 4.45 x 2.72
Weight
1.62 oz (46 gm)
1.62 oz (46 gm)
1.62 oz (46 gm)
Size (in)
0.95 x 2.00 x 1.20
0.95 x 2.00 x 1.20
0.95 x 2.00 x 1.20
(cm)
2.41 x 5.08 x 3.05
2.41 x 5.08 x 3.05
2.41 x 5.08 x 3.05
Weight
2.40 oz (68 gm)
2.40 oz (68 gm)
2.40 oz (68 gm)
Pin Diagram
Electrical
Physical
Standard package
Aluminum package (-AL option)
Notes
1
-3dB, DC coupled sensor
Non-linearity is the deviation from a best fit straight line at full scale. Transverse sensitivity is error measured in the primary axis output created
by forces induced in the orthogonal axis. Transverse sensitivity error is primarily due to the effects of misalignment. Zero g drift is specified as the
typical change in 0 g level from its initial value at +25°C to its worst case value at Tmin or Tmax. Specifications subject to change without notice.
High Temperature Package Dimensions
Ordering Information
Model
Axes
Span
(g)
Sensitivity Noise (mg
(m V/g)
rms)
Bandwidth
(Hz)
CXL04GP1
X
±4
500
10
DC-100
CXL04GP1Z
Z
±4
500
10
DC-100
CXL04GP3
TRI
±4
500
10
DC-100
CXL10GP1
X
± 10
200
25
DC-100
CXL10GP1Z
Z
± 10
200
25
DC-100
CXL10GP3
TRI
± 10
200
25
DC-100
CXL25GP1
X
± 25
80
25
DC-100
CXL25GP1Z
Z
± 25
80
25
DC-100
CXL25GP3
TRI
± 25
80
25
DC-100
OPTIONS
-R
Voltage Regulator, 5.5 – 36 VDC input. (Available in GP3 models only.)
-AL
High Temperature Package. Operating Temperature Range (°C): -40 to +105.
(Available in GP3 models only.)
High Temperature Package
MEMSIC Inc.
San Jose, California
w w w. m e m s i c . c o m
6020-0114-03 Rev B
Similar pages