STMicroelectronics L4931ABV52 Very low drop voltage regulators with inhibit Datasheet

L4931
SERIES
VERY LOW DROP
VOLTAGE REGULATORS WITH INHIBIT
■
■
■
■
■
■
■
■
■
■
VERY LOW DROPOUT VOLTAGE (0.4V)
VERY LOW QUIESCENT CURRENT
(TYP. 50 µA IN OFF MODE, 600µA IN ON
MODE)
OUTPUT CURRENT UP TO 250 mA
LOGIC-CONTROLLED ELECTRONIC
SHUTDOWN
OUTPUT VOLTAGES OF 1.25; 1.5; 2.5; 2.7;
3; 3.3; 3.5; 4; 4.5; 4.7; 5; 5.2; 5.5; 6; 8; 12V
INTERNAL CURRENT AND THERMAL LIMIT
ONLY 2.2µF FOR STABILITY
AVAILABLE IN ± 1% (AB) OR 2% (C)
SELECTION AT 25°C
SUPPLY VOLTAGE REJECTION: 70db TYP.
FOR 5V VERSION
TEMPERATURE RANGE: -40 TO 125°C
DESCRIPTION
The L4931 series are very Low Drop regulators
available in TO-220, SO-8, DPAK, PPAK and
TO-92 packages and in a wide range of output
voltages.
The very Low Drop voltage (0.4V) and the very
low quiescent current make them particularly
suitable for Low Noise, Low Power applications
and specially in battery powered systems.
TO-220
PPAK
TO-92
DPAK
SO-8
In PPAK and SO-8 packages a Shutdown Logic
Control function is available TTL compatible. This
means that when the device is used as a local
regulator, it is possible to put a part of the board in
standby, decreasing the total power consumption.
It requires only a 2.2 µF capacitor for stability
allowing space and cost saving.
SCHEMATIC DIAGRAM
January 2004
1/29
L4931 SERIES
ABSOLUTE MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
20
V
VI
DC Input Voltage
IO
Output Current
Internally Limited
Internally Limited
Ptot
Power Dissipation
Tstg
Storage Temperature Range
-40 to 150
°C
Top
Operating Junction Temperature Range
-40 to 125
°C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is
not implied.
THERMAL DATA
Symbol
Parameter
TO-220
SO-8
DPAK
PPAK
Rthj-case Thermal Resistance Junction-case
3
20
8
8
Rthj-amb Thermal Resistance Junction-ambient
50
55(*)
100
100
2
(*) Considering 6 cm of copper board heat-sink
CONNECTION DIAGRAM (top view)
TO-220
SO-8
DPAK
PPAK
PIN 1 = VOUT
PIN 2 = GND
PIN 3 = VIN
TO-92
BOTTOM VIEW
2/29
TO-92
Unit
°C/W
200
°C/W
L4931 SERIES
ORDERING CODES
TO-220
SO-8
PPAK
DPAK
TO-92
OUTPUT
VOLTAGE
L4931CV12 (*)
L4931ABV12 (*)
L4931CV15 (*)
L4931ABV15 (*)
L4931CV25 (*)
L4931ABV25 (*)
L4931CV27
L4931ABV27
L4931CV30
L4931ABV30
L4931CV33
L4931ABV33
L4931CV35
L4931ABV35
L4931CV40
L4931ABV40
L4931CV45 (*)
L4931ABV45 (*)
L4931CV47
L4931ABV47
L4931CV50
L4931ABV50
L4931CV52 (*)
L4931ABV52 (*)
L4931CV55 (*)
L4931ABV55 (*)
L4931CV60
L4931ABV60
L4931CV80
L4931ABV80
L4931CV120
L4931ABV120
L4931CD12 (*)
L4931ABD12 (*)
L4931CD15 (*)
L4931ABD15 (*)
L4931CD25
L4931ABD25
L4931CD27
L4931ABD27
L4931CD30
L4931ABD30
L4931CD33
L4931ABD33
L4931CD35
L4931ABD35
L4931CD40
L4931ABD40
L4931CD45 (*)
L4931ABD45 (*)
L4931CD47
L4931ABD47
L4931CD50
L4931ABD50
L4931CD52 (*)
L4931ABD52 (*)
L4931CD55 (*)
L4931ABD55 (*)
L4931CD60
L4931ABD60
L4931CD80
L4931ABD80
L4931CD120
L4931ABD120
L4931CPT12 (*)
L4931ABPT12 (*)
L4931CPT15 (*)
L4931ABPT15 (*)
L4931CPT25 (*)
L4931ABPT25 (*)
L4931CPT27
L4931ABPT27
L4931CPT30
L4931ABPT30
L4931CPT33
L4931ABPT33
L4931CPT35
L4931ABPT35
L4931CPT40
L4931ABPT40
L4931CPT45 (*)
L4931ABPT45 (*)
L4931CPT47
L4931ABPT47
L4931CPT50
L4931ABPT50
L4931CPT52 (*)
L4931ABPT52 (*)
L4931CPT55 (*)
L4931ABPT55 (*)
L4931CPT60
L4931ABPT60
L4931CPT80
L4931ABPT80
L4931CPT120
L4931ABPT120
L4931CDT12 (*)
L4931ABDT12 (*)
L4931CDT15 (*)
L4931ABDT15 (*)
L4931CDT25
L4931ABDT25
L4931CDT27
L4931ABDT27
L4931CDT30
L4931ABDT30
L4931CDT33
L4931ABDT33
L4931CDT35
L4931ABDT35
L4931CDT40
L4931ABDT40
L4931CDT45 (*)
L4931ABDT45 (*)
L4931CDT47
L4931ABDT47
L4931CDT50
L4931ABDT50
L4931CDT52 (*)
L4931ABDT52 (*)
L4931CDT55 (*)
L4931ABDT55 (*)
L4931CDT60
L4931ABDT60
L4931CDT80
L4931ABDT80
L4931CDT120
L4931ABDT120
L4931CZ12 (*)
L4931ABZ12 (*)
L4931CZ15 (*)
L4931ABZ15 (*)
L4931CZ25 (*)
L4931ABZ25 (*)
L4931CZ27
L4931ABZ27
L4931CZ30
L4931ABZ30
L4931CZ33
L4931ABZ33
L4931CZ35
L4931ABZ35
L4931CZ40
L4931ABZ40
L4931CZ45 (*)
L4931ABZ45 (*)
L4931CZ47
L4931ABZ47
L4931CZ50
L4931ABZ50
L4931CZ52 (*)
L4931ABZ52 (*)
L4931CZ55 (*)
L4931ABZ55 (*)
L4931CZ60
L4931ABZ60
L4931CZ80
L4931ABZ80
L4931CZ120
L4931ABZ120
1.25 V
1.25 V
1.5 V
1.5 V
2.5 V
2.5 V
2.7 V
2.7 V
3V
3V
3.3 V
3.3 V
3.5 V
3.5 V
4V
4V
4.5 V
4.5 V
4.75 V
4.75 V
5V
5V
5.2 V
5.2 V
5.5 V
5.5 V
6V
6V
8V
8V
12 V
12 V
(*) Available on request.
3/29
L4931 SERIES
TEST CIRCUITS
ELECTRICAL CHARACTERISTICS OF L4931ABxx12 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
Parameter
VO
Output Voltage
VI
Operating Input Voltage
Test Conditions
IO = 5 mA
VI = 3.3 V
IO = 5 mA
VI = 3.3 V
TA=-25 to 85°C
IO = 250 mA
Iout
Output Current Limit
∆VO
Line Regulation
∆VO(*)
Load Regulation
VI = 2.7 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 2.7 to 20 V
IO = 0 mA
VI = 2.7 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 3.7 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Id
Control Input Logic Low
TA= -40 to 125°C
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
Unit
1.238
1.25
1.263
V
1.225
1.275
2.5
20
V
3
15
mV
3
15
mV
0.6
1
mA
IO = 0.5 mA
4
6
100
80
77
55
50
1.25
IO = 0 to 250 mA
2
µA
dB
µV
V
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
mA
50
2
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
4/29
Max.
f = 120 Hz
f = 1 KHz
f = 10 KHz
VIL
II
Typ.
300
VI = 2.5 to 20 V
VIH
CO
Min.
V
V
10
µA
10
µF
L4931 SERIES
ELECTRICAL CHARACTERISTICS OF L4931Cxx12 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 3.3 V
IO = 5 mA
VI = 3.3 V
TA=-25 to 85°C
IO = 250 mA
Min.
Typ.
Max.
Unit
1.225
1.25
1.275
V
1.2
1.3
2.5
20
300
V
mA
∆VO
Line Regulation
VI = 2.5 to 20 V
IO = 0.5 mA
3
18
mV
∆VO(*)
Load Regulation
VI = 2.7 V
IO = 0.5 to 250 mA
3
18
mV
Quiescent Current
ON MODE
VI = 2.7 to 20 V
IO = 0 mA
0.6
1
mA
VI = 2.7 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 3.7 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Id
f = 120 Hz
f = 1 KHz
f = 10 KHz
VIL
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
II
CO
4
6
50
100
80
77
55
50
1.25
dB
µV
V
0.8
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 250 mA
2
µA
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
ELECTRICAL CHARACTERISTICS OF L4931ABxx15 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 3.5 V
IO = 5 mA
VI = 3.5 V
TA=-25 to 85°C
IO = 250 mA
Min.
Typ.
Max.
Unit
1.485
1.5
1.515
V
1.47
1.53
2.5
20
300
V
mA
∆VO
Line Regulation
VI = 2.5 to 20 V
IO = 0.5 mA
3
15
mV
∆VO(*)
Load Regulation
VI = 2.7 V
IO = 0.5 to 250 mA
3
15
mV
Quiescent Current
ON MODE
VI = 2.7 to 20 V
IO = 0 mA
0.6
1
mA
VI = 2.7 to 20 V
IO = 250 mA
4
6
50
100
f = 120 Hz
f = 1 KHz
f = 10 KHz
79
76
55
50
1
Id
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 3.7 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
VIL
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
II
CO
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
µV
V
0.8
2
VC = 6 V
IO = 0 to 250 mA
2
µA
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
5/29
L4931 SERIES
ELECTRICAL CHARACTERISTICS OF L4931Cxx15 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 3.5 V
IO = 5 mA
VI = 3.5 V
TA=-25 to 85°C
IO = 250 mA
Min.
Typ.
Max.
Unit
1.47
1.5
1.53
V
1.44
1.56
2.5
20
300
V
mA
∆VO
Line Regulation
VI = 2.5 to 20 V
IO = 0.5 mA
3
18
mV
∆VO(*)
Load Regulation
VI = 2.7 V
IO = 0.5 to 250 mA
3
18
mV
Quiescent Current
ON MODE
VI = 2.7 to 20 V
IO = 0 mA
0.6
1
mA
VI = 2.7 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 3.7 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Id
f = 120 Hz
f = 1 KHz
f = 10 KHz
VIL
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
II
CO
4
6
50
100
79
76
55
50
1
dB
µV
V
0.8
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 250 mA
2
µA
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
ELECTRICAL CHARACTERISTICS OF L4931ABxx25 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 4.5 V
IO = 5 mA
VI = 4.5 V
TA=-25 to 85°C
Min.
Typ.
Max.
Unit
2.475
2.5
2.525
V
2.45
2.55
IO = 250 mA
20
300
V
mA
∆VO
Line Regulation
VI = 3.2 to 20 V
IO = 0.5 mA
3
15
mV
∆VO(*)
Load Regulation
VI = 3.4 V
IO = 0.5 to 250 mA
3
15
mV
Quiescent Current
ON MODE
VI = 3.4 to 20 V
IO = 0 mA
0.6
1
mA
VI = 3.4 to 20 V
IO = 250 mA
4
6
50
100
Id
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 4.4 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
TJ= -40 to 125°C
VIL
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
II
CO
dB
0.6
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 250 mA
µA
µV
V
0.8
2
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
6/29
75
72
55
50
0.4
2
V
V
10
µA
10
µF
L4931 SERIES
ELECTRICAL CHARACTERISTICS OF L4931Cxx25 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 4.5 V
IO = 5 mA
VI = 4.5 V
TA=-25 to 85°C
Min.
Typ.
Max.
Unit
2.45
2.5
2.55
V
2.4
2.6
IO = 250 mA
20
300
V
mA
∆VO
Line Regulation
VI = 3.3 to 20 V
IO = 0.5 mA
3
18
mV
∆VO(*)
Load Regulation
VI = 3.5 V
IO = 0.5 to 250 mA
3
18
mV
Quiescent Current
ON MODE
VI = 3.5 to 20 V
IO = 0 mA
0.6
1
mA
VI = 3.5 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 4.4 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Id
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
CO
6
100
75
72
55
50
0.4
TJ= -40 to 125°C
VIL
II
4
50
dB
0.6
2
VC = 6 V
IO = 0 to 250 mA
µV
V
0.8
0.8
Output Bypass Capacitance ESR = 0.1 to 10 Ω
µA
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
ELECTRICAL CHARACTERISTICS OF L4931ABxx27 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
Parameter
VO
Output Voltage
VI
Operating Input Voltage
Test Conditions
IO = 5 mA
VI = 4.7 V
IO = 5 mA
VI = 4.7 V
TA=-25 to 85°C
Iout
Output Current Limit
Line Regulation
∆VO(*)
Load Regulation
VI = 3.6 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 3.6 to 20 V
IO = 0 mA
VI = 3.6 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 4.6 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Unit
2.673
2.7
2.727
V
2.646
IO = 0.5 mA
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
2.754
20
V
3
15
mV
3
15
mV
0.6
1
mA
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
4
6
100
74
71
55
50
0.4
dB
0.6
0.8
2
IO = 0 to 250 mA
µA
µV
V
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
mA
50
TJ= -40 to 125°C
Control Input Logic Low
CO
Max.
300
VI = 3.4 to 20 V
VIL
II
Typ.
IO = 250 mA
∆VO
Id
Min.
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
7/29
L4931 SERIES
ELECTRICAL CHARACTERISTICS OF L4931Cxx27 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified). .
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 4.7 V
IO = 5 mA
VI = 4.7 V
TA=-25 to 85°C
Min.
Typ.
2.646
2.7
2.592
Max.
Unit
2.754
V
2.808
IO = 250 mA
20
300
V
mA
∆VO
Line Regulation
VI = 3.4 to 20 V
IO = 0.5 mA
3
18
mV
∆VO(*)
Load Regulation
VI = 3.6 V
IO = 0.5 to 250 mA
3
18
mV
Quiescent Current
ON MODE
VI = 3.6 to 20 V
IO = 0 mA
0.6
1
mA
VI = 3.6 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 4.6 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Id
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
CO
6
100
74
71
55
50
0.4
TJ= -40 to 125°C
VIL
II
4
50
dB
0.6
2
VC = 6 V
IO = 0 to 250 mA
µV
V
0.8
0.8
Output Bypass Capacitance ESR = 0.1 to 10 Ω
µA
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
ELECTRICAL CHARACTERISTICS OF L4931ABxx30 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
Parameter
VO
Output Voltage
VI
Operating Input Voltage
Test Conditions
IO = 5 mA
VI = 5 V
IO = 5 mA
VI = 5 V
TA=-25 to 85°C
Iout
Output Current Limit
Line Regulation
∆VO(*)
Load Regulation
VI = 3.9 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 3.9 to 20 V
IO = 0 mA
VI = 3.9 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 4.9 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
IO = 250 mA
2.97
3
3.03
V
2.94
3.06
20
V
IO = 0.5 mA
3
15
mV
3
15
mV
0.6
1
mA
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
4
6
100
74
71
55
50
0.4
dB
0.6
0.8
2
IO = 0 to 250 mA
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
µA
µV
V
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
mA
50
TJ= -40 to 125°C
TA= -40 to 125°C
8/29
Unit
f = 120 Hz
f = 1 KHz
f = 10 KHz
Control Input Logic Low
CO
Max.
300
VI = 3.7 to 20 V
VIL
II
Typ.
IO = 250 mA
∆VO
Id
Min.
2
V
V
10
µA
10
µF
L4931 SERIES
ELECTRICAL CHARACTERISTICS OF L4931Cxx30 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 5 V
IO = 5 mA
VI = 5 V
TA=-25 to 85°C
Min.
Typ.
2.94
3
2.88
Max.
Unit
3.06
V
3.12
IO = 250 mA
20
300
V
mA
∆VO
Line Regulation
VI = 3.8 to 20 V
IO = 0.5 mA
3
18
mV
∆VO(*)
Load Regulation
VI = 4 V
IO = 0.5 to 250 mA
3
18
mV
Quiescent Current
ON MODE
VI = 4 to 20 V
IO = 0 mA
0.6
1
mA
VI = 4 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 5 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Id
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
CO
6
100
74
71
55
50
0.4
TJ= -40 to 125°C
VIL
II
4
50
dB
0.6
2
VC = 6 V
IO = 0 to 250 mA
µV
V
0.8
0.8
Output Bypass Capacitance ESR = 0.1 to 10 Ω
µA
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
ELECTRICAL CHARACTERISTICS OF L4931ABxx33 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
Parameter
VO
Output Voltage
VI
Operating Input Voltage
Test Conditions
IO = 5 mA
VI = 5.3 V
IO = 5 mA
VI = 5.3 V
TA=-25 to 85°C
Iout
Output Current Limit
Line Regulation
∆VO(*)
Load Regulation
VI = 4.2 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 4.2 to 20 V
IO = 0 mA
VI = 4.2 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 5.2 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Unit
3.267
3.3
3.333
V
3.234
IO = 0.5 mA
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
3.366
20
V
3
15
mV
3
15
mV
0.6
1
mA
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
4
6
100
73
70
55
50
0.4
dB
0.6
0.8
2
IO = 0 to 250 mA
µA
µV
V
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
mA
50
TJ= -40 to 125°C
Control Input Logic Low
CO
Max.
300
VI = 4 to 20 V
VIL
II
Typ.
IO = 250 mA
∆VO
Id
Min.
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
9/29
L4931 SERIES
ELECTRICAL CHARACTERISTICS OF L4931Cxx33 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 5.3 V
IO = 5 mA
VI = 5.3 V
TA=-25 to 85°C
Min.
Typ.
3.234
3.3
3.168
Max.
Unit
3.366
V
3.432
IO = 250 mA
20
300
V
mA
∆VO
Line Regulation
VI = 4.1 to 20 V
IO = 0.5 mA
3
18
mV
∆VO(*)
Load Regulation
VI = 4.3 V
IO = 0.5 to 250 mA
3
18
mV
Quiescent Current
ON MODE
VI = 4.3 to 20 V
IO = 0 mA
0.6
1
mA
VI = 4.3 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 5.3 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Id
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
CO
6
100
73
70
55
50
0.4
TJ= -40 to 125°C
VIL
II
4
50
dB
0.6
2
VC = 6 V
IO = 0 to 250 mA
µV
V
0.8
0.8
Output Bypass Capacitance ESR = 0.1 to 10 Ω
µA
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
ELECTRICAL CHARACTERISTICS OF L4931ABxx35 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
Parameter
VO
Output Voltage
VI
Operating Input Voltage
Test Conditions
IO = 5 mA
VI = 5.5 V
IO = 5 mA
VI = 5.5 V
TA=-25 to 85°C
Iout
Output Current Limit
Line Regulation
∆VO(*)
Load Regulation
VI = 4.4 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 4.4 to 20 V
IO = 0 mA
VI = 4.4 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 5.4 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
IO = 250 mA
3.465
3.5
3.535
V
3.43
3.57
20
V
IO = 0.5 mA
3
15
mV
3
15
mV
0.6
1
mA
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
4
6
100
73
70
55
50
0.4
dB
0.6
0.8
2
IO = 0 to 250 mA
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
µA
µV
V
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
mA
50
TJ= -40 to 125°C
TA= -40 to 125°C
10/29
Unit
f = 120 Hz
f = 1 KHz
f = 10 KHz
Control Input Logic Low
CO
Max.
300
VI = 4.2 to 20 V
VIL
II
Typ.
IO = 250 mA
∆VO
Id
Min.
2
V
V
10
µA
10
µF
L4931 SERIES
ELECTRICAL CHARACTERISTICS OF L4931Cxx35 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 5.5 V
IO = 5 mA
VI = 5.5 V
TA=-25 to 85°C
Min.
Typ.
Max.
Unit
3.43
3.5
3.57
V
3.36
3.64
IO = 250 mA
20
300
V
mA
∆VO
Line Regulation
VI = 4.3 to 20 V
IO = 0.5 mA
3
18
mV
∆VO(*)
Load Regulation
VI = 4.5 V
IO = 0.5 to 250 mA
3
18
mV
Quiescent Current
ON MODE
VI = 4.5 to 20 V
IO = 0 mA
0.6
1
mA
VI = 4.5 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 5.5 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Id
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
CO
6
100
73
70
55
50
0.4
TJ= -40 to 125°C
VIL
II
4
50
dB
0.6
2
VC = 6 V
IO = 0 to 250 mA
µV
V
0.8
0.8
Output Bypass Capacitance ESR = 0.1 to 10 Ω
µA
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
ELECTRICAL CHARACTERISTICS OF L4931ABxx40 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
Parameter
VO
Output Voltage
VI
Operating Input Voltage
Test Conditions
IO = 5 mA
VI = 6 V
IO = 5 mA
VI = 6 V
TA=-25 to 85°C
Iout
Output Current Limit
Line Regulation
∆VO(*)
Load Regulation
VI = 4.9 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 4.9 to 20 V
IO = 0 mA
VI = 4.9 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 5.9 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Unit
3.96
4
4.04
V
3.92
IO = 0.5 mA
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
4.08
20
V
3.5
17.5
mV
3
15
mV
0.6
1
mA
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
4
6
100
72
69
55
50
0.4
dB
0.6
0.8
2
IO = 0 to 250 mA
µA
µV
V
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
mA
50
TJ= -40 to 125°C
Control Input Logic Low
CO
Max.
300
VI = 4.7 to 20 V
VIL
II
Typ.
IO = 250 mA
∆VO
Id
Min.
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
11/29
L4931 SERIES
ELECTRICAL CHARACTERISTICS OF L4931Cxx40 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 6 V
IO = 5 mA
VI = 6 V
TA=-25 to 85°C
4
3.84
Unit
4.08
V
4.16
20
Line Regulation
VI = 4.8 to 20 V
IO = 0.5 mA
Load Regulation
VI = 5 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 5 to 20 V
IO = 0 mA
VI = 5 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 6 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
21
mV
3
18
mV
0.6
1
mA
4
6
50
100
72
69
55
50
0.4
0.6
µV
V
0.8
2
VC = 6 V
IO = 0 to 250 mA
µA
dB
0.8
Output Bypass Capacitance ESR = 0.1 to 10 Ω
V
mA
3.5
TJ= -40 to 125°C
VIL
CO
3.92
Max.
300
∆VO
II
Typ.
IO = 250 mA
∆VO(*)
Id
Min.
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
ELECTRICAL CHARACTERISTICS OF L4931ABxx45 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
Parameter
VO
Output Voltage
VI
Operating Input Voltage
Test Conditions
IO = 5 mA
VI = 6.5 V
IO = 5 mA
VI = 6.5 V
TA=-25 to 85°C
Iout
Output Current Limit
Line Regulation
∆VO(*)
Load Regulation
VI = 5.4 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 5.4 to 20 V
IO = 0 mA
VI = 5.4 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 6.4 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
IO = 250 mA
4.455
4.5
4.545
V
4.41
4.59
20
V
IO = 0.5 mA
3.5
17.5
mV
3
15
mV
0.6
1
mA
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
4
6
100
71
68
55
50
0.4
dB
0.6
0.8
2
IO = 0 to 250 mA
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
µA
µV
V
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
mA
50
TJ= -40 to 125°C
TA= -40 to 125°C
12/29
Unit
f = 120 Hz
f = 1 KHz
f = 10 KHz
Control Input Logic Low
CO
Max.
300
VI = 5.2 to 20 V
VIL
II
Typ.
IO = 250 mA
∆VO
Id
Min.
2
V
V
10
µA
10
µF
L4931 SERIES
ELECTRICAL CHARACTERISTICS OF L4931Cxx45 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 6.5 V
IO = 5 mA
VI = 6.5 V
TA=-25 to 85°C
Unit
4.41
4.5
4.59
V
4.32
4.68
20
Line Regulation
VI = 5.3 to 20 V
IO = 0.5 mA
Load Regulation
VI = 5.5 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 5.5 to 20 V
IO = 0 mA
VI = 5.5 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 6.5 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
21
mV
3
18
mV
0.6
1
mA
4
6
50
100
71
68
55
50
0.4
0.6
µV
V
0.8
2
VC = 6 V
IO = 0 to 250 mA
µA
dB
0.8
Output Bypass Capacitance ESR = 0.1 to 10 Ω
V
mA
3.5
TJ= -40 to 125°C
VIL
CO
Max.
300
∆VO
II
Typ.
IO = 250 mA
∆VO(*)
Id
Min.
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
ELECTRICAL CHARACTERISTICS OF L4931ABxx47 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
Parameter
VO
Output Voltage
VI
Operating Input Voltage
Test Conditions
IO = 5 mA
VI = 6.7 V
IO = 5 mA
VI = 6.7 V
TA=-25 to 85°C
Iout
Output Current Limit
Line Regulation
∆VO(*)
Load Regulation
VI = 5.6 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 5.6 to 20 V
IO = 0 mA
VI = 5.6 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 6.6 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Unit
4.653
4.7
4.747
V
4.606
IO = 0.5 mA
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
4.794
20
V
3.5
17.5
mV
3
15
mV
0.6
1
mA
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
4
6
100
71
68
55
50
0.4
dB
0.6
0.8
2
IO = 0 to 250 mA
µA
µV
V
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
mA
50
TJ= -40 to 125°C
Control Input Logic Low
CO
Max.
300
VI = 5.4 to 20 V
VIL
II
Typ.
IO = 250 mA
∆VO
Id
Min.
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
13/29
L4931 SERIES
ELECTRICAL CHARACTERISTICS OF L4931Cxx47 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 6.7 V
IO = 5 mA
VI = 6.7 V
TA=-25 to 85°C
4.7
4.512
Unit
4.794
V
4.888
20
Line Regulation
VI = 5.5 to 20 V
IO = 0.5 mA
Load Regulation
VI = 5.7 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 5.7 to 20 V
IO = 0 mA
VI = 5.7 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 6.7 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
21
mV
3
18
mV
0.6
1
mA
4
6
50
100
71
68
55
50
0.4
0.6
µV
V
0.8
2
VC = 6 V
IO = 0 to 250 mA
µA
dB
0.8
Output Bypass Capacitance ESR = 0.1 to 10 Ω
V
mA
3.5
TJ= -40 to 125°C
VIL
CO
4.606
Max.
300
∆VO
II
Typ.
IO = 250 mA
∆VO(*)
Id
Min.
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
ELECTRICAL CHARACTERISTICS OF L4931ABxx50 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
Parameter
VO
Output Voltage
VI
Operating Input Voltage
Test Conditions
IO = 5 mA
VI = 7 V
IO = 5 mA
VI = 7 V
TA=-25 to 85°C
Iout
Output Current Limit
Line Regulation
∆VO(*)
Load Regulation
VI = 6 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 6 to 20 V
IO = 0 mA
VI = 6 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 7 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
IO = 250 mA
4.95
5
5.05
V
4.9
5.1
20
V
IO = 0.5 mA
3.5
17.5
mV
3
15
mV
0.6
1
mA
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
4
6
100
70
67
55
50
0.4
dB
0.6
0.8
2
IO = 0 to 250 mA
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
µA
µV
V
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
mA
50
TJ= -40 to 125°C
TA= -40 to 125°C
14/29
Unit
f = 120 Hz
f = 1 KHz
f = 10 KHz
Control Input Logic Low
CO
Max.
300
VI = 5.8 to 20 V
VIL
II
Typ.
IO = 250 mA
∆VO
Id
Min.
2
V
V
10
µA
10
µF
L4931 SERIES
ELECTRICAL CHARACTERISTICS OF L4931Cxx50 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 7 V
IO = 5 mA
VI = 7 V
TA=-25 to 85°C
5
4.8
Unit
5.1
V
5.2
20
Line Regulation
VI = 5.8 to 20 V
IO = 0.5 mA
Load Regulation
VI = 6 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 6 to 20 V
IO = 0 mA
VI = 6 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 7 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
17.5
mV
3
15
mV
0.6
1
mA
4
6
50
100
70
67
55
50
0.4
0.6
µV
V
0.8
2
VC = 6 V
IO = 0 to 250 mA
µA
dB
0.8
Output Bypass Capacitance ESR = 0.1 to 10 Ω
V
mA
3.5
TJ= -40 to 125°C
VIL
CO
4.9
Max.
300
∆VO
II
Typ.
IO = 250 mA
∆VO(*)
Id
Min.
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
ELECTRICAL CHARACTERISTICS OF L4931ABxx52 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
Parameter
VO
Output Voltage
VI
Operating Input Voltage
Test Conditions
IO = 5 mA
VI = 7.2 V
IO = 5 mA
VI = 7.2 V
TA=-25 to 85°C
Iout
Output Current Limit
Line Regulation
∆VO(*)
Load Regulation
VI = 6.2 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 6.2 to 20 V
IO = 0 mA
VI = 6.2 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 7.2 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Unit
5.148
5.2
5.252
V
5.096
IO = 0.5 mA
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
5.304
20
V
3.5
17.5
mV
3
15
mV
0.6
1
mA
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
4
6
100
70
67
55
50
0.4
dB
0.6
0.8
2
IO = 0 to 250 mA
µA
µV
V
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
mA
50
TJ= -40 to 125°C
Control Input Logic Low
CO
Max.
300
VI = 6 to 20 V
VIL
II
Typ.
IO = 250 mA
∆VO
Id
Min.
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
15/29
L4931 SERIES
ELECTRICAL CHARACTERISTICS OF L4931Cxx52 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 7.2 V
IO = 5 mA
VI = 7.2 V
TA=-25 to 85°C
5.2
4.992
Unit
5.304
V
5.408
20
Line Regulation
VI = 6 to 20 V
IO = 0.5 mA
Load Regulation
VI = 6.2 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 6.2 to 20 V
IO = 0 mA
VI = 6.2 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 7.2 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
21
mV
3
18
mV
0.6
1
mA
4
6
50
100
70
67
55
50
0.4
0.6
µV
V
0.8
2
VC = 6 V
IO = 0 to 250 mA
µA
dB
0.8
Output Bypass Capacitance ESR = 0.1 to 10 Ω
V
mA
3.5
TJ= -40 to 125°C
VIL
CO
5.096
Max.
300
∆VO
II
Typ.
IO = 250 mA
∆VO(*)
Id
Min.
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
ELECTRICAL CHARACTERISTICS OF L4931ABxx55 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
Parameter
VO
Output Voltage
VI
Operating Input Voltage
Test Conditions
IO = 5 mA
VI = 7.5 V
IO = 5 mA
VI = 7.5 V
TA=-25 to 85°C
Iout
Output Current Limit
Line Regulation
∆VO(*)
Load Regulation
VI = 6.5 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 6.5 to 20 V
IO = 0 mA
VI = 6.5 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 7.5 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
IO = 250 mA
5.445
5.5
5.555
V
5.39
5.61
20
V
IO = 0.5 mA
3.5
17.5
mV
3
15
mV
0.6
1
mA
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
4
6
100
70
67
55
50
0.4
dB
0.6
0.8
2
IO = 0 to 250 mA
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
µA
µV
V
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
mA
50
TJ= -40 to 125°C
TA= -40 to 125°C
16/29
Unit
f = 120 Hz
f = 1 KHz
f = 10 KHz
Control Input Logic Low
CO
Max.
300
VI = 6.3 to 20 V
VIL
II
Typ.
IO = 250 mA
∆VO
Id
Min.
2
V
V
10
µA
10
µF
L4931 SERIES
ELECTRICAL CHARACTERISTICS OF L4931Cxx55 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 7.5 V
IO = 5 mA
VI = 7.5 V
TA=-25 to 85°C
Unit
5.39
5.5
5.61
V
5.28
5.72
20
Line Regulation
VI = 6.3 to 20 V
IO = 0.5 mA
Load Regulation
VI = 6.5 V
IO = 0.5 to 250 mA
Quiescent Current
ON MODE
VI = 6.5 to 20 V
IO = 0 mA
VI = 6.5 to 20 V
IO = 250 mA
OFF MODE
VI = 6 V
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 7.5 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
21
mV
3
18
mV
0.6
1
mA
4
6
50
100
70
67
55
50
0.4
0.6
µV
V
0.8
2
VC = 6 V
IO = 0 to 250 mA
µA
dB
0.8
Output Bypass Capacitance ESR = 0.1 to 10 Ω
V
mA
3.5
TJ= -40 to 125°C
VIL
CO
Max.
300
∆VO
II
Typ.
IO = 250 mA
∆VO(*)
Id
Min.
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
ELECTRICAL CHARACTERISTICS OF L4931ABxx60 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
Parameter
VO
Output Voltage
VI
Operating Input Voltage
Test Conditions
IO = 5 mA
VI = 8 V
IO = 5 mA
VI = 8 V
TA=-25 to 85°C
Min.
Typ.
Max.
Unit
5.94
6
6.06
V
5.88
6.12
IO = 250 mA
20
V
20
mV
Iout
Output Current Limit
∆VO
Line Regulation
∆VO(*)
Load Regulation
VI = 7 V
IO = 0.5 to 250 mA
3
15
mV
Quiescent Current
ON MODE
VI = 7 to 20 V
IO = 0 mA
0.8
1.6
mA
VI = 7 to 20 V
IO = 250 mA
4.5
7
OFF MODE
VI = 6 V
70
140
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 8 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Id
300
VI = 6.8 to 20 V
IO = 250 mA
69
66
55
50
0.4
TJ= -40 to 125°C
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
CO
4
f = 120 Hz
f = 1 KHz
f = 10 KHz
VIL
II
IO = 0.5 mA
dB
0.6
0.8
2
IO = 0 to 250 mA
µA
µV
V
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
mA
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
17/29
L4931 SERIES
ELECTRICAL CHARACTERISTICS OF L4931Cxx60 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 8 V
IO = 5 mA
VI = 8 V
TA=-25 to 85°C
Min.
Typ.
5.88
6
5.76
Max.
Unit
6.12
V
6.24
IO = 250 mA
20
300
V
mA
∆VO
Line Regulation
VI = 6.8 to 20 V
IO = 0.5 mA
4
24
mV
∆VO(*)
Load Regulation
VI = 7 V
IO = 0.5 to 250 mA
3
18
mV
Quiescent Current
ON MODE
VI = 7 to 20 V
IO = 0 mA
0.8
1.6
mA
VI = 7 to 20 V
IO = 250 mA
4.5
7
OFF MODE
VI = 6 V
70
140
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 8 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Id
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
TJ= -40 to 125°C
VIL
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
II
CO
69
66
55
50
0.4
dB
0.6
2
VC = 6 V
IO = 0 to 250 mA
µV
V
0.8
0.8
Output Bypass Capacitance ESR = 0.1 to 10 Ω
µA
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
ELECTRICAL CHARACTERISTICS OF L4931ABxx80 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
Parameter
VO
Output Voltage
VI
Operating Input Voltage
Test Conditions
IO = 5 mA
VI = 10 V
IO = 5 mA
VI = 10 V
TA=-25 to 85°C
Min.
Typ.
Max.
Unit
7.92
8
8.08
V
7.84
8.16
IO = 250 mA
20
V
20
mV
Iout
Output Current Limit
∆VO
Line Regulation
∆VO(*)
Load Regulation
VI = 9 V
IO = 0.5 to 250 mA
3
15
mV
Quiescent Current
ON MODE
VI = 9 to 20 V
IO = 0 mA
0.8
1.6
mA
VI = 9 to 20 V
IO = 250 mA
4.5
7
OFF MODE
VI = 6 V
70
140
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 10 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Id
300
VI = 8.8 to 20 V
IO = 250 mA
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
2
IO = 0 to 250 mA
µA
dB
0.6
µV
V
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
mA
0.8
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
18/29
67
64
55
50
0.4
TJ= -40 to 125°C
Control Input Logic Low
CO
4
f = 120 Hz
f = 1 KHz
f = 10 KHz
VIL
II
IO = 0.5 mA
2
V
V
10
µA
10
µF
L4931 SERIES
ELECTRICAL CHARACTERISTICS OF L4931Cxx80 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 10 V
IO = 5 mA
VI = 10 V
TA=-25 to 85°C
Min.
Typ.
7.84
8
7.68
Max.
Unit
8.16
V
8.32
IO = 250 mA
20
300
V
mA
∆VO
Line Regulation
VI = 8.9 to 20 V
IO = 0.5 mA
4
24
mV
∆VO(*)
Load Regulation
VI = 9.1 V
IO = 0.5 to 250 mA
3
18
mV
Quiescent Current
ON MODE
VI = 9.1 to 20 V
IO = 0 mA
0.8
1.6
mA
VI = 9.1 to 20 V
IO = 250 mA
4.5
7
OFF MODE
VI = 6 V
70
140
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 10.1 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Id
IO = 250 mA
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
CO
67
64
55
50
0.4
TJ= -40 to 125°C
VIL
II
f = 120 Hz
f = 1 KHz
f = 10 KHz
dB
0.6
2
VC = 6 V
IO = 0 to 250 mA
µV
V
0.8
0.8
Output Bypass Capacitance ESR = 0.1 to 10 Ω
µA
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
ELECTRICAL CHARACTERISTICS OF L4931ABxx120 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
Parameter
VO
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
∆VO
Line Regulation
∆VO(*)
Test Conditions
IO = 5 mA
VI = 14 V
IO = 5 mA
VI = 14 V
TA=-25 to 85°C
Min.
Typ.
Max.
Unit
11.88
12
12.12
V
11.76
12.24
IO = 250 mA
20
V
20
mV
300
IO = 0.5 mA
Load Regulation
VI = 13 V
IO = 0.5 to 250 mA
3
15
mV
Quiescent Current
ON MODE
VI = 13 to 20 V
IO = 0 mA
0.8
1.6
mA
VI = 13 to 20 V
IO = 250 mA
4.5
7
OFF MODE
VI = 6 V
90
180
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 14 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Id
f = 120 Hz
f = 1 KHz
f = 10 KHz
IO = 250 mA
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
CO
64
61
55
50
0.4
TJ= -40 to 125°C
VIL
II
4
mA
VI = 12.8 to 20 V
dB
0.6
0.8
2
IO = 0 to 250 mA
µV
V
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
µA
2
V
V
10
µA
10
µF
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
19/29
L4931 SERIES
ELECTRICAL CHARACTERISTICS OF L4931Cxx120 (refer to the test circuits, TJ = 25°C,
CI = 0.1 µF, C O = 2.2 µF unless otherwise specified).
Symbol
VO
Parameter
Output Voltage
VI
Operating Input Voltage
Iout
Output Current Limit
Test Conditions
IO = 5 mA
VI = 14 V
IO = 5 mA
VI = 14 V
TA=-25 to 85°C
Min.
Typ.
11.76
12
11.52
Max.
Unit
12.24
V
12.48
IO = 250 mA
20
300
V
mA
∆VO
Line Regulation
VI = 12.9 to 20 V
IO = 0.5 mA
4
24
mV
∆VO(*)
Load Regulation
VI = 13.1 V
IO = 0.5 to 250 mA
3
18
mV
Quiescent Current
ON MODE
VI = 13.1 to 20 V
IO = 0 mA
0.8
1.6
mA
VI = 13.1 to 20 V
IO = 250 mA
4.5
7
OFF MODE
VI = 6 V
90
180
SVR
Supply Voltage Rejection
IO = 5 mA
VI = 14.1 ± 1 V
eN
Vd(*)
Output Noise Voltage
Dropout Voltage
B =10 Hz to 100 KHz
IO = 250 mA
Id
IO = 250 mA
Control Input Logic Low
TA= -40 to 125°C
VIH
Control Input Logic High
TA= -40 to 125°C
Control Input Current
VI = 6 V,
CO
0.6
2
IO = 0 to 250 mA
µV
V
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
0.8
(*) For SO-8 package the maximum limit of load regulation and dropout is increased by 20 mV.
20/29
64
61
55
50
0.4
TJ= -40 to 125°C
VIL
II
f = 120 Hz
f = 1 KHz
f = 10 KHz
µA
2
V
V
10
µA
10
µF
L4931 SERIES
Figure 1 : Supply Current vs Output Current
Figure 4 : Supply Current vs Temperature
Figure 2 : Dropout Voltage vs Temperature
Figure 5 : Short Circuit Current vs Dropout
Voltage
Figure 3 : Supply Current vs Input Voltage
Figure 6 : S.V.R. vs Input Voltage Signal
Frequency
21/29
L4931 SERIES
TO-220 MECHANICAL DATA
DIM.
mm.
MIN.
TYP
inch
MAX.
MIN.
TYP.
MAX.
A
4.40
4.60
0.173
0.181
C
1.23
1.32
0.048
0.051
D
2.40
2.72
0.094
0.107
D1
1.27
0.050
E
0.49
0.70
0.019
0.027
F
0.61
0.88
0.024
0.034
F1
1.14
1.70
0.044
0.067
F2
1.14
1.70
0.044
0.067
G
4.95
5.15
0.194
0.203
G1
2.4
2.7
0.094
0.106
H2
10.0
10.40
0.393
0.409
L2
16.4
0.645
L4
13.0
14.0
0.511
0.551
L5
2.65
2.95
0.104
0.116
L6
15.25
15.75
0.600
0.620
L7
6.2
6.6
0.244
0.260
L9
3.5
3.93
0.137
0.154
DIA.
3.75
3.85
0.147
0.151
P011C
22/29
L4931 SERIES
TO-92 MECHANICA DATA
mm.
mils
DIM.
MIN.
TYP
MAX.
MIN.
TYP.
MAX.
A
4.32
4.95
170.1
194.9
b
0.36
0.51
14.2
20.1
D
4.45
4.95
175.2
194.9
E
3.30
3.94
129.9
155.1
e
2.41
2.67
94.9
105.1
e1
1.14
1.40
44.9
55.1
L
12.7
15.49
500.0
609.8
R
2.16
2.41
85.0
94.9
S1
0.92
1.52
36.2
59.8
W
0.41
0.56
16.1
22.0
0102782/C
23/29
L4931 SERIES
SO-8 MECHANICAL DATA
DIM.
mm.
MIN.
TYP
inch
MAX.
MIN.
TYP.
MAX.
A
1.35
1.75
0.053
0.069
A1
0.10
0.25
0.04
0.010
A2
1.10
1.65
0.043
0.065
B
0.33
0.51
0.013
0.020
C
0.19
0.25
0.007
0.010
D
4.80
5.00
0.189
0.197
E
3.80
4.00
0.150
0.157
e
1.27
0.050
H
5.80
6.20
0.228
0.244
h
0.25
0.50
0.010
0.020
L
0.40
1.27
0.016
0.050
k
ddd
8˚ (max.)
0.1
0.04
0016023/C
24/29
L4931 SERIES
DPAK MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
MAX.
MIN.
TYP.
MAX.
A
2.2
2.4
0.086
A1
0.9
1.1
0.035
0.094
0.043
A2
0.03
0.23
0.001
0.009
B
0.64
0.9
0.025
0.035
B2
5.2
5.4
0.204
0.212
C
0.45
0.6
0.017
0.023
C2
0.48
0.6
0.019
0.023
D
6
6.2
0.236
D1
E
5.1
6.4
0.244
0.200
6.6
0.252
0.260
E1
4.7
0.185
e
2.28
0.090
e1
4.4
4.6
0.173
0.181
H
9.35
10.1
0.368
0.397
L
(L1)
L2
L4
1
0.039
2.8
0.110
0.8
0.6
0.031
1
0.023
0.039
0068772-F
25/29
L4931 SERIES
PPAK MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
MAX.
MIN.
TYP.
MAX.
A
2.2
2.4
0.086
0.094
A1
0.9
1.1
0.035
0.043
A2
0.03
0.23
0.001
0.009
B
0.4
0.6
0.015
0.023
B2
5.2
5.4
0.204
0.212
C
0.45
0.6
0.017
0.023
C2
0.48
0.6
0.019
0.023
D
6
6.2
0.236
0.244
E
6.4
6.6
0.252
0.260
G
4.9
5.25
0.193
0.206
G1
2.38
2.7
0.093
0.106
H
9.35
10.1
0.368
0.397
L2
L4
0.8
0.6
0.031
1
0.023
0.039
0078180-B
26/29
L4931 SERIES
Tape & Reel DPAK-PPAK MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
A
MAX.
MIN.
TYP.
330
13.0
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
13.2
MAX.
0.504
0.512
22.4
0.519
0.882
Ao
6.80
6.90
7.00
0.268
0.272
0.2.76
Bo
10.40
10.50
10.60
0.409
0.413
0.417
Ko
2.55
2.65
2.75
0.100
0.104
0.105
Po
3.9
4.0
4.1
0.153
0.157
0.161
P
7.9
8.0
8.1
0.311
0.315
0.319
27/29
L4931 SERIES
Tape & Reel SO-8 MECHANICAL DATA
mm.
inch
DIM.
MIN.
A
MAX.
MIN.
330
13.2
TYP.
MAX.
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
28/29
TYP
0.504
22.4
0.519
0.882
Ao
8.1
8.5
0.319
0.335
Bo
5.5
5.9
0.216
0.232
Ko
2.1
2.3
0.082
0.090
Po
3.9
4.1
0.153
0.161
P
7.9
8.1
0.311
0.319
L4931 SERIES
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from
its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications
mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information
previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or
systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics
All other names are the property of their respective owners
© 2004 STMicroelectronics - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States.
http://www.st.com
29/29
Similar pages