STMicroelectronics AN3112 Solution for designing a fixed off-time controlled pfc pre-regulator Datasheet

AN3112
Application note
Solution for designing a fixed off-time controlled PFC pre-regulator
with the L6564
Introduction
In this document we propose a third approach to the operation of PFC pre-regulators. In
addition to the transition mode (TM) and the fixed-frequency continuous conduction mode
(FF-CCM) operation of PFC pre-regulators, an alternative approach is offered that couples
the simplicity and affordability of TM operation with the high-current capability of FF-CCM
operation. This solution is a peak current-mode control with fixed-off-time (FOT). Design
equations are given and a practical design for a 400 W board is illustrated and evaluated.
Two methods of controlling power factor corrector (PFC) pre-regulators, based on boost
topology, are currently in use: the fixed-frequency (FF) PWM and the transition mode (TM)
PWM (fixed on-time, variable frequency). The first method employs average current-mode
control, a relatively complex technique requiring sophisticated controller ICs (e.g. the
L4981A/B from STMicroelectronics) and a considerable component count. The second uses
the more simple peak current-mode control, which is implemented with cheaper controller
ICs (e.g. the L6561, L6562, L6562A and L6564 from STMicroelectronics), and much fewer
external parts making it far more cost efficient. In the first method the boost inductor works
in a continuous conduction mode (CCM), while TM makes the inductor work on the
boundary between continuous and discontinuous mode. For a given power throughput, TM
operation involves higher peak currents compared to FF-CCM (Figure 1 and Figure 2).
Figure 1.
Line, inductor, switch and diode
currents in FF-CCM PFC
Figure 2.
Line, inductor, switch and diode
currents in TM PFC
This demonstration, consistent with the above mentioned cost considerations, suggests the
use of TM in a lower power range, while FF-CCM is recommended for higher power levels.
This criterion, though always true, is sometimes difficult to apply, especially for a mid-range
power level of around 150-300 W. Assessing which approach gives the better
cost/performance trade-off needs to be done on a case-by-case basis, considering the cost
and the stress of both power semiconductors and magnetics, but also of the EMI filter. At the
same power level, the switching frequency component to be filtered out in a TM system is
twice the line current, whereas it is typically 1/3 or 1/4 in a CCM system.
February 2011
Doc ID 16820 Rev 3
1/36
www.st.com
Contents
AN3112
Contents
1
Introduction to FOT control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2
Operation of an FOT- controlled PFC pre-regulator . . . . . . . . . . . . . . . . 5
3
Implementing the line-modulated fixed-off-time . . . . . . . . . . . . . . . . . . 6
4
Designing a fixed-off-time PFC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.1
Input specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2
Operating condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.3
Power section design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.3.1
Bridge rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.3.2
Input capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3.3
Output capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3.4
Boost inductor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.3.5
Power MOSFET selection and power dissipation calculation . . . . . . . . 16
4.3.6
Boost diode selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.3.7
L6564 biasing circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5
Design example using the L6564-FOT PFC Excel® spreadsheet . . . . 31
6
Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2/36
Doc ID 16820 Rev 3
AN3112
List of figures
List of figures
Figure 1.
Line, inductor, switch and diode currents in FF-CCM PFC. . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 2.
Line, inductor, switch and diode currents in TM PFC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 3.
Basic waveforms for fixed frequency PWM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Figure 4.
Basic waveforms for fixed-off-time PWM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Figure 5.
Block diagram of an FOT-controlled PFC pre-regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 6.
Circuit implementing FOT control with the L6564 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 7.
ZCD pin signal with the fixed off-time generator circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 8.
Switching frequency fixing the line voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 9.
The effect of fixing off-time - boundary between DCM and CCM . . . . . . . . . . . . . . . . . . . . 16
Figure 10. Conduction losses and total losses in the STP12NM50FP MOSFET couples for the 400W
FOT PFC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 11. L6564 internal schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 12. Open loop transfer function-bode plot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 13. Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 14. Multiplier characteristics family for VFF =1 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 15. Multiplier characteristics family for VFF=3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 16. Switching frequency function on the peak of the sinusoid input voltage waveform and the corresponding off- time value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 17. Off-time vs. input mains voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 18. Switching frequency vs. input mains voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 19. Excel spreadsheet design specification input table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 20. Other design data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 21. Excel spreadsheet FOT PFC schematic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 22. Excel spreadsheet BOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Doc ID 16820 Rev 3
3/36
Introduction to FOT control
1
AN3112
Introduction to FOT control
In the output power range already mentioned, where the TM/CCM usability boundary is
uncertain, a third approach that couples the simplicity and affordability of TM operation with
the high-current capability of CCM operation may offer a solution to the problem. Generally
speaking, FF PWM is not the only alternative when CCM operation is desired. FF PWM
modulates both switch on and off-times (their sum is constant by definition), and a given
converter operates in either CCM or DCM depending on the input voltage and the loading
conditions. Exactly the same result can be achieved if just the on-time is modulated and the
off-time is kept constant, in which case, however, the switching frequency is no longer fixed
(Figure 3 and Figure 4). This is referred to as fixed-off-time (FOT) control. Peak-currentmode control can still be used.
Figure 3.
Basic waveforms for fixed
frequency PWM
Figure 4.
Basic waveforms for fixed-off-time
PWM
It is worth noting that FOT control does not need a specialized control IC. A simple
modification of a standard TM PFC controller operation, requiring just a few additional
passive parts and no significant extra cost, is all that is needed.
4/36
Doc ID 16820 Rev 3
AN3112
2
Operation of an FOT- controlled PFC pre-regulator
Operation of an FOT- controlled PFC pre-regulator
In Figure 5 a block diagram of an FOT-controlled PFC pre-regulator is shown. An error
amplifier (VA) compares a portion of the pre-regulator's output voltage Vout with a reference
Vref and generates an error signal VC proportional to their difference. VC, a DC voltage by
hypothesis, is fed into an input of the multiplier block and multiplied by a portion of the
rectified input voltage VMULT. At the output of the multiplier, there is a rectified sinusoid,
VCSREF, whose amplitude is proportional to that of VMULT and to VC, which represents the
sinusoidal reference for PWM modulation. VCSREF is fed into the inverting input of a
comparator that, on the non-inverting input, receives the voltage VCS on the sense resistor
Rsense, proportional to the current flowing through the M switch (typically a MOSFET) and
the L inductor during the on-time of M. When the two voltages are equal, the comparator
resets the PWM latch, and M, supposedly already on, is switched off.
Figure 5.
Block diagram of an FOT-controlled PFC pre-regulator
As a result, VCSREF determines the peak current through M and the L inductor. As VCSREF is
a rectified sinusoid, the inductor peak current is also enveloped by a rectified sinusoid. The
line current Iin is the average inductor current that is the low-frequency component of the
inductor current resulting from the low-pass filtering operated by the EMI filter. The PWM
latch output Q going high activates the timer that, after a predetermined time in which TOFF
has elapsed, sets the PWM latch, therefore turning M on and starting another switching
cycle. If TOFF is such that the inductor current does not fall to zero, the system operates in
CCM. It is apparent that FOT control requires nearly the same architecture as TM control,
the only change is the way the off-time of M is determined. It is not a difficult task to modify
externally the operation of the standard TM PFC controller so that the off-time of M is fixed.
For the controller, we refer to the L6564 [4]. For a more detailed and complex description of
the fixed off-time technique and in particular the line modulated FOT, please refer to [5].
Doc ID 16820 Rev 3
5/36
Implementing the line-modulated fixed-off-time
3
AN3112
Implementing the line-modulated fixed-off-time
The circuit that implements LM-FOT control with the L6564 PFC controller is shown in
Figure 6. During the on-time of the MOSFET the gate voltage VGD = 15 V is high, diode D is
forward biased and the voltage at the ZCD pin is internally clamped at VZCDclamp (5.7 V
typ.). During the MOSFET off-time VGD is low, diode D is reverse-biased and the voltage at
the pin decays with an exponential law until it reaches the triggering threshold (VZCDtrigger ~
0.7 V typ.) which causes the switch to turn on. The time needed for the ZCD voltage to go
from VZCDclamp (clamping level) to VZCDtrigger (trigger level) defines the duration of the offtime, or TOFF.
Figure 6.
Circuit implementing FOT control with the L6564
The circuit in Figure 6. makes TOFF a function of the RMS line voltage thanks to the peak
holding effect of T1 (which acts as a buffer) along with R and C whose time constant is
significantly longer than a line half-cycle. With the addition of R0 and T1, as long as the
voltage on the ZCD pin during TOFF is above Vmult+VBE, C is discharged through R and R0,
following the law:
Equation 1
t⋅(R +R 0 )
⎡
⎤ −
R
R
′ (t) = ⎢VZCDclamp −
⋅ (Vmult + VBE )⎥ ⋅ e (RR0 )⋅C +
⋅ (Vmult + VBE )
VZCD
+
R
R
R
0
0 +R
⎣
⎦
As V’ZCD(t) falls below Vmult+VBE, T1 is cut off and C is discharged through R only, so that its
evolution from that point on is described as:
Equation 2
t
−
R
′′ (t) =
VZCD
⋅ (Vmult + VBE ) ⋅ e R⋅C
R0 + R
V'ZCD(t) decreases from VZCDclamp = 5.7 V to Vmult+VBE in the following time period t':
6/36
Doc ID 16820 Rev 3
AN3112
Implementing the line-modulated fixed-off-time
Equation 3
t′ = −
⎡
⎤
(Vmult + VBE ) ⋅ R0
R ⋅ R0
⋅ C ⋅ ln⎢
⎥
R + R0
⎢⎣ VZCDclamp ⋅ (R + R0 ) − (Vmult + VBE ) ⋅ R ⎥⎦
and V''ZCD(t) decreases from Vmult+VBE to VZCDtrigger = 0.7 V (trigger level) in the following
time period t'':
Equation 4
⎡ VZCDtrigger ⎤
t′′ = −RC ⋅ ln⎢
⎥
⎣ Vmult + VBE ⎦
Figure 7 illustrates the signal on the ZCD pin with the two discharging time constants
depending on the two resistors R, R0 and the L6564 parameters, particularly the upper
clamp voltage and the triggering voltage of the ZCD pin.
Figure 7.
ZCD pin signal with the fixed off-time generator circuit
The sum of the two time periods is the off-time function:
Equation 5
⎡ R
⎤
⎡
⎛ VZCDtrigger ⎞⎤
(Vmult + VBE ) ⋅ R 0
0
⎟⎥
TOFF = −RC ⋅ ⎢
⋅ ln⎢
⎥ + ln⎜⎜
⎟
⎢⎣ R + R 0
⎢⎣ VZCDclamp ⋅ (R + R 0 ) − (Vmult + VBE ) ⋅ R ⎥⎦
⎝ (Vmult + VBE ) ⎠⎥⎦
In this way, once the multiplier operating point (that is, the Vmult /VAC ratio) is fixed, with the
proper selection of R and R0, it is possible to increase TOFF with the line voltage so that, at
maximum line voltage, it is always TON>TONmin, where TONmin is the minimum on-time of the
L6564 gate drive [4]. This is a required condition in order to avoid line distortion [5].
Doc ID 16820 Rev 3
7/36
Implementing the line-modulated fixed-off-time
AN3112
It is easy to see that TOFF is now a function of the instantaneous line voltage. We refer to this
technique as line-modulated fixed-off-time (LM-FOT) [5].
This modification, although simple, introduces profound changes in the timing relationships,
with a positive influence on the energetic relationships. From the control point of view,
modulating TOFF is a feed-forward term that modifies the gain but does not change its
characteristics. Consequently, all of the properties of the standard FOT control are
maintained. Due to the highly non-linear nature of the TOFF modulation introduced by T1
and R0, its effects are discussed only qualitatively and the quantitative aspects are provided
graphically for a specific case in [5].
As a practical rule, it is convenient to first select a capacitor and then to calculate the resistor
needed to achieve the desired TOFF (see Section 4.3.7 on page 19).
As the gate voltage VGD rises, the Rs resistor charges the C timing capacitor as quickly as
possible up to VZCDclamp, without exceeding the clamp rating (IZCDx =10 mA). Then it must
fulfill the following inequalities:
Equation 6
VGDx − VZCDclamp − VF
VGD − VZCDclamp − VF
< Rs < R ⋅
VZCDclamp
VZCDclamp
IZCDx +
R
where VGD (assume VGD = 10 V) is the voltage delivered by the gate driver, VGDx = 15 V its
maximum value, and VF the forward drop on D.
When working at high line/light load the on-time of the power switch becomes very short and
the Rs resistor alone is no longer able to charge C up to VZCDclamp. The speed-up capacitor
Cs is then used in parallel to Rs. This capacitor causes an almost instantaneous charge of C
up to a certain level, after that, Rs completes the charge up to VZCDclamp. It is important that
the steep edge caused by Cs does not reach the clamp level, otherwise the internal clamp of
the L6564 undergoes uncontrolled current spikes (limited only by the dynamic resistance of
the 1N4148 and the ESR of Cs) that could overstress the IC. Cs must then be:
Equation 7
Cs < C
8/36
VZCDclamp
VGDx − VZCDclamp − VF
Doc ID 16820 Rev 3
AN3112
Designing a fixed-off-time PFC
4
Designing a fixed-off-time PFC
4.1
Input specification
The following is a possible design procedure for a fixed-off-time mode PFC using the L6564.
This first part is a detailed specification of the operating conditions of the circuit that is
needed for the calculations in Section 4.2 on page 11. In this example a 400 W, wide-input
range mains PFC circuit is considered. Some design criteria are also given.
●
Mains voltage range (Vac rms):
VACmin = 90Vac VACmax = 265 Vac
(1)
●
Minimum mains frequency:
fl = 47Hz
(2)
●
Rated output power (W):
Pout = 400 W
(3)
Because the PFC is a boost topology the regulated output voltage depends strongly on the
maximum AC input voltage. In fact, for correct boost operation the output voltage must
always be higher than the input and therefore, as Vin max is Vpk, the output has been set at
400 Vdc as the typical value. In cases where the maximum AC input voltage VACmax is
higher than 265 V, as typical in ballast applications, the output voltage must be set higher
accordingly. As a rule of thumb the output voltage must be set 6/7% higher than the
maximum input voltage peak.
●
Regulated DC output voltage (Vdc) Vout = 400 V
(4)
The target efficiency and PF are set here at minimum input voltage and maximum load.
They are used for the following operating condition calculation of the PFC. Of course at high
input voltage there is higher efficiency.
Pout
= 90%
Pin
●
Expected efficiency (%):
η=
●
Expected power factor:
PF = 0.99
(5)
(6)
Because of the narrow loop voltage bandwidth, the PFC output may experience
overvoltages at startup or in the case of load transients. To protect from excessive output
voltages that can overstress the output components and the load, in the L6564, a device pin
(PFC_OK, pin #6) has been dedicated to monitor the output voltage with a separate resistor
divider, selected so that the voltage at the pin reaches 2.5 V if the output voltage exceeds a
preset value (Vovp) larger than the maximum Vout that can be expected, also including
worst-case load/line transients.
Doc ID 16820 Rev 3
9/36
Designing a fixed-off-time PFC
●
AN3112
Maximum. output voltage (Vdc):
VOVP = 430 V
(7)
The mains frequency generates a 2fL voltage ripple on the output voltage at full load. The
ripple amplitude determines the current flowing into the output capacitor and the ESR.
Additionally, a certain hold-up capability in case of mains dips can be requested from the
PFC in which case the output capacitor must also be dimensioned, taking into account the
required minimum voltage value (Vout min) after the elapsed hold-up time (tHold).
●
Maximum output low frequency ripple: ∆Vout = 10 V
(8)
●
Minimum output voltage after line drop (Vdc): Vout min = 300 V
(9)
●
Hold-up capability
(ms):
tHold = 20ms
(10)
The PFC minimum switching frequency is one of the main parameters used to dimension
the boost inductor. Here we consider the switching frequency at low mains on top of the
sinusoid and at full load conditions. As a rule of thumb, it must be higher than the audio
bandwidth in order to avoid audible noise and additionally it must not interfere with the
L6564 minimum internal starter period, as given in the datasheet. Alternatively, if the
minimum frequency is set too high the circuit shows excessive losses at higher input voltage
and probably operates skipping switching cycles not only at light load. The typical minimum
frequency range is 55÷95 kHz for wide range operation.
●
Minimum switching frequency (kHz) fsw min = 80kHz
(11)
The design is done on the basis of a ripple factor (the ratio of the maximum current ripple
amplitude to the inductor peak current at minimum line voltage) kr=0.34.
●
Ripple factor
k r = 0.34
(12)
In order to properly select the power components of the PFC and dimension the heat sinks
in case they are needed, the maximum operating ambient temperature around the PFC
circuit must be known. Please note that this is not the maximum external operating
temperature of the entire equipment, but it is the local temperature at which the PFC
components are working.
●
10/36
Maximum ambient temperature (°C): Tambx = 50°C
Doc ID 16820 Rev 3
(13)
AN3112
4.2
Designing a fixed-off-time PFC
Operating condition
The first step is to define the main parameters of the circuit, using the specification points
given in Section 4.1 on page 9:
Rated DC output current:
Equation 8
Iout =
Pout
Vout
Iout =
400 W
= 1.00A
400 V
Maximum input power:
Equation 9
Pin =
Pout
400 W
Pin =
⋅ 100 = 444.44W
η
90
Referring to the main currents shown in Figure 1, the following formula expresses the
maximum value of current circulating in the boost cell which means at minimum line voltage
of the selected range:
RMS input current:
Equation 10
Iin =
Pout
400 W
Iin =
= 4.99 A
VAC min ⋅ PF
90 Vac ⋅ 0.99
It is important to define the following ratios in order to continue describing the energetic
relationships in the PFC:
Equation 11
k min = 2
VAC min
Vout
k min = 2
90 Vac
= 0.32
400 V
Equation 12
k max = 2
VAC max
265 Vac
k max = 2
= 0.94
Vout
400 V
From Equation 11 and Equation 12:
Line peak current:
Equation 13
IPK max =
2 ⋅ Pin
2 ⋅ 444.44 W
IPK max =
= 6.98 A
k min ⋅ Vout
0.32 ⋅ 400 V
Inductor Ripple-∆ILpk:
Doc ID 16820 Rev 3
11/36
Designing a fixed-off-time PFC
AN3112
Equation 14
∆IL pk =
6 ⋅ kr
6 ⋅ 0.34
⋅ IPK max ∆IL pk =
⋅ 6.98 A = 2.04 A
8 − 3 ⋅ kr
8 − 3 ⋅ 0.34
Inductor peak current:
Equation 15
IL pk max =
8
8
⋅ IPK max IL pk max =
⋅ 6.98A = 8.01A
8 − 3 ⋅ kr
8 − 3 ⋅ 0.34
It is also possible to calculate the RMS current flowing into the switch and into the diode,
needed to calculate the losses of these two elements.
RMS switch current:
Equation 16
ISWrms =
Pin
16 ⋅ k min
⋅ 2−
k min ⋅ Vout
3π
ISWrms =
400 W
16 ⋅ 0.32
⋅ 2−
= 4.22A
0.32 ⋅ 400 V
3π
RMS diode current:
Equation 17
IDrms =
Pin
16k min
400 W
16 ⋅ 0.32
⋅
IDrms =
⋅
= 2.57 A
k min ⋅ Vout
3π
0.32 ⋅ 400 V
3π
It is worth remembering that the accuracy of the approximate energetic relationships
described here is quite good at maximum load for low values of parameter k, that is, at low
line voltage, but worsens at high line and as the power throughput is reduced. Since, in the
design phase, current stress is calculated at maximum load and minimum line voltage, their
accuracy is acceptable for design purposes.
4.3
Power section design
4.3.1
Bridge rectifier
The input rectifier bridge can use standard slow recovery, low-cost devices.
Typically a 600 V device is selected in order to obtain a good margin against mains surges.
An NTC resistor, limiting the current at turn-on, is required to avoid overstress to the diode
bridge.
The rectifier bridge power dissipation can be calculated using equations
Equation 18,Equation 19,Equation 20. The threshold voltage (Vth) and dynamic resistance
(Rdiode) of a single diode bridge can be found in the component datasheet.
12/36
Doc ID 16820 Rev 3
AN3112
Designing a fixed-off-time PFC
Equation 18
Iinrms =
2 ⋅ Iin
=
2
2 ⋅ 4.99A
= 3.53A
2
Iin _ avg =
2 ⋅ Iin
=
π
2 ⋅ 4.99A
= 2.25A
π
Equation 19
The power dissipated on a D15XB60 bridge may be:
Equation 20
Pbridge = 4 ⋅ R diode ⋅ I 2 inrms + 4 ⋅ Vth ⋅ Iin _ avg
Pbridge = 4 ⋅ 0.025Ω ⋅ (3.53A )2 + 4 ⋅ 0.7V ⋅ 2.25A = 7.53W
4.3.2
Input capacitor
The input filter capacitor (Cin) is placed across the diode bridge output. This capacitor must
smooth the high-frequency ripple and must sustain the maximum instantaneous input
voltage. In a typical application an EMI filter is placed between the mains and the PFC
circuit. In this application the EMI filter is reinforced by a differential mode Pi-filter after the
bridge to reject the differential noise coming from the whole switching circuit. The design of
the EMI filter (common mode and differential mode) is not described here. The value of the
input filter capacitor can be calculated as follows, simply considering the output power that
the PFC should deliver at full load:
Equation 21
Cin = 2.5 ⋅ 10 −3 ⋅ Pout Cin = 2.5 ⋅ 10 −3 ⋅ 400 W = 1µF
The maximum value of this capacitor is limited to avoid line current distortion. The value
chosen for this design is 1 µF.
4.3.3
Output capacitor
The output bulk capacitor (Co) selection depends on the DC output voltage (4), the allowed
maximum voltage (7) and the converter output power (3).
The 100/120 Hz (twice the mains frequency) voltage ripple (Vout = peak-to-peak ripple
value) (8) is a function of the capacitor impedance and the peak capacitor current:
Equation 22
∆Vout = 2 ⋅ Iout ⋅
1
(2π ⋅ 2fl ⋅ CO )
2
+ ESR 2
With a low ESR capacitor the capacitive reactance is dominant, therefore:
Doc ID 16820 Rev 3
13/36
Designing a fixed-off-time PFC
AN3112
Equation 23
CO ≥
Iout
Pout
=
2π ⋅ fl ⋅ ∆Vout 2π ⋅ fl ⋅ Vout ⋅ ∆Vout
CO ≥
400 W
= 338µF
2π ⋅ 47Hz ⋅ 400 V ⋅ 10V
Vout is usually selected in the range of 1.5% of the output voltage. Although ESR does not
usually affect the output ripple, it should be taken into account for power loss calculations.
The total RMS capacitor ripple current, including mains frequency and switching frequency
components, is:
Equation 24
ICrms = ID 2rms − I2out
ICrms =
(2.56A )2 − (1.0A )2
= 2.36 A
If the PFC stage must guarantee a specified hold-up time, the selection criterion of the
capacitance is different. Co has to deliver the output power for a certain time (tHold) with a
specified maximum dropout voltage (Vout min) that is the minimum output voltage value
(which takes load regulation and output ripple into account). Vout min is the minimum output
operating voltage before the 'power fail' detection and consequent stopping by the
downstream system supplied by the PFC.
Equation 25
CO =
2 ⋅ Pout ⋅ tHold
(V
out
− ∆Vout
)
2
−
2
Vout
min
CO =
2 ⋅ 400 W ⋅ 20ms
(400V − 10V )2 − (300V )2
= 242.3µF
A 20% tolerance on the electrolytic capacitors must be taken into account for correct
dimensioning.
Following the previous relationships, after selecting the commercial value of 330 µF the
actual hold-up capability and ripple voltage are recalculated.
In detail:
Equation 26
t hold
(
C O ⋅ ⎡⎢ Vout − ∆Vout
⎣
=
2 ⋅ Pout
)
2
[
]
⎤
2
2
2
− Vout
330µF ⋅ (400 V − 10 V ) − (300 V )
min ⎥
⎦ t hold =
= 22ms
2 ⋅ 400 W
Equation 27
∆Vout =
4.3.4
Iout
2 ⋅ π ⋅ fl ⋅ CO
∆Vout =
1 .0 A
= 10.2V
2 ⋅ π ⋅ 47Hz ⋅ 330µF
Boost inductor
In the continuous mode approach, the acceptable current ripple factor, Kr, is typically fixed in
the range between 10% to 35%. For this design, the maximum specified current ripple factor
is 34%.
14/36
Doc ID 16820 Rev 3
AN3112
Designing a fixed-off-time PFC
To calculate the required inductance L of the boost inductor, use the following formula with a
3.76 µs off-time set at 90 Vac (see the following ZCD pin dimensioning to find the meaning
of this value):
Equation 28
L(VAC) = (1 − k min ) ⋅
Vout
TOFF (VAC) L(VAC min ) = (1 − 0.32) ⋅ 400 V 3.76µs = 501µH
∆IL pk
2.04A
After calculating the inductor value at low mains and at high mains L(VACmax), L(VACmin)
(Equation 28) depending also on the off-time, the minimum value must be taken into
account. It becomes the maximum inductance value for the PFC dimensioning.
Figure 8 shows the switching frequency versus the θ angle calculated inverting Equation 28
with a 500 µH boost inductance and fixing the line voltage at minimum and maximum
values.
Switching frequency fixing the line voltage
Frequency modulation with the Line half period
1000
CCM
DCM
100
DCM
kHz
Figure 8.
TM
TM
10
Switching Freq.@VacMin
Switching Freq.@VacMax
1
0
θ1 0.4
0.8
1.2
1.6
2
2.4
2.8θ2
÷θ[ Line half period]
Doc ID 16820 Rev 3
15/36
Designing a fixed-off-time PFC
Figure 9.
AN3112
The effect of fixing off-time - boundary between DCM and CCM
CCM
TM
DCM
Half Line Cycle
TOFF
θ1
The effect of fixing the off-time is to generate a continuous conduction mode in the center
region of the line half-cycle between the two transition angles. Close to the zero-crossing,
the system works in discontinuous conduction mode and in transition mode at the boundary.
The inductor core size is determined assuming a peak flux density Bx ~0.25 T (depending
on the ferrite grade selected and relevant specific losses) and calculating the maximum
current according to Equation 15 as a function of the maximum current sense pin clamping
voltage and sense resistor value.
DC and AC copper losses and ferrite losses must also be calculated to determine the
maximum temperature rise of the inductor.
4.3.5
Power MOSFET selection and power dissipation calculation
The selection of the MOSFET concerns mainly its RDS(on), basically proportional to the
output power. The MOSFET breakdown voltage is selected considering the PFC nominal
output voltage (4) adding some margin (20%) to guarantee reliable operation.
Therefore, a voltage rating of 500 V (1.2 · Vout = 480 V) is selected. Using its current rating
as a rule of thumb, we can select a device having ~ 3 times the RMS switch current
(Equation 16) but, the power dissipation calculation gives the final confirmation that the
selected device is the right one for the circuit, also taking the heat sink dimensions into
account. For example, in a 400 W PFC application two parallel STP12NM50FP MOSFETs
can be selected.
The MOSFET's power dissipation depends on conduction, switching and capacitive losses.
The conduction losses at maximum load and minimum input voltage are calculated by:
Equation 29
Pcond (VAC) = RDS on ⋅ (ISWrms (VAC))
2
Because, normally in the datasheets the RDS(on) is given at an ambient temperature (25 °C),
to correctly calculate the conduction losses at 100°C (typical MOSFET junction operating
16/36
Doc ID 16820 Rev 3
AN3112
Designing a fixed-off-time PFC
temperature), a factor of 1.75 to 2 should be taken into account. The exact factor can be
found on the device datasheet.
Now, combining equations Equation 29 and Equation 16, the conduction losses referred to a
1 ΩRDS(on), at ambient temperature as a function of Pin and VAC can be calculated:
Equation 30
⎛
Pin
16 ⋅ k(VAC) ⎞⎟
′ (VAC) = 2 ⋅ (ISWrms (VAC)) = 2 ⋅ ⎜
Pcond
⋅ 2−
⎜ k(VAC) ⋅ Vout
⎟
3π
⎝
⎠
2
2
The generic switching losses due to the MOSFET commutation occurring at turn-on and
turn-off can be basically expressed by:
Equation 31
⎛t +t ⎞
Pswitch (VAC) = VMOS ⋅ IMOS ⋅ ⎜ rise fall ⎟ ⋅ fsw (VAC)
2
⎝
⎠
Because the switching frequency depends on the input line voltage and phase angle on the
sinusoidal waveform, it can be demonstrated that from Equation 31 the switching losses per
1 µs of current, rise and fall-time can be written as:
Equation 32
∆IL pk
⎛
′
Pswitch
(VAC) = Vout ⋅ ⎜⎜ IL pk max −
2
⎝
π
⎞ 1
2
⎟⋅
⎟ π (sin ϑ) ⋅ fsw (VAC, θ) ⋅ dϑ
⎠
0
∫
From the STP12NM50FP datasheet trise = tfall = 0.01 µs is the crossover time at turn-on
and off.
At turn-on the losses are due to the discharge of the total drain capacitance inside the
MOSFET itself. In general, the capacitive losses are given by:
Equation 33
Pcap (VAC) =
1
⋅ C d ⋅ V 2MOS ⋅ fsw (VAC)
2
Where Cd is the total drain capacitance including the MOSFET and the other parasitic
capacitances such as inductor etc. At the drain node, VMOS is the drain voltage at MOSFET
turn-on.
Taking into account the frequency variation with the input line voltage and the phase angle,
the capacitive losses per 1 nF of total drain capacitance can be calculated as:
Equation 34
′ (VAC) =
Pcap
1 1
⋅
2 π
π
∫ (V
out
)2 fsw (VAC, ϑ) ⋅dϑ
0
The total drain capacitance (Cd) of the two parallel MOSFETs is 0.36 nF, not including the
other component contributions, Vout is the drain voltage at MOSFET turn-on.
Doc ID 16820 Rev 3
17/36
Designing a fixed-off-time PFC
AN3112
The MOSFET total losses as a function of the input mains voltage is the sum of the three
previous losses from Equation 30, Equation 32, and Equation 34, multiplied for relevant
MOSFET parameters:
Equation 35
⎛t +t ⎞
′ (VAC) + ⎜ rise fall ⎟ ⋅ Psw
′ (VAC) + C d ⋅ Pcap
′ (VAC)
Ploss (VAC) = RDS on ⋅ Pcond
2
⎝
⎠
From Equation 35 using the data relevant to the MOSFET selected, the losses at Vitamin
and VACmax can be calculated and plotted like in Figure 10. We can observe that the
maximum total losses is 9 W and it occurs at VACmin. From this number and the given
maximum ambient temperature (13), the total maximum thermal resistance required to keep
the junction temperature below 125°C is:
Equation 36
R th =
125°C − Tambx
125°C − 50°C
°C
R th =
= 8 .1
Ploss (VAC)
9W
W
If the result of Equation 36 is lower than the junction-ambient thermal resistance given in the
MOSFET datasheet for the selected device package, a heat sink must be used.
Figure 10. Conduction losses and total losses in the STP12NM50FP MOSFET
couples for the 400W FOT PFC
MOSFETS total losses
25
Plosses(Vi)
Range Limi ts
P losses [W]
20
15
10
5
0
85
110
135
160
185
210
Vin_ac [Vr ms]
235
260
285
Figure 10 shows the trend of the total losses (Equation 35) versus the input line voltage for
two selected STP12NM50FP MOSFETs.
4.3.6
Boost diode selection
Following a similar criterion to that of the MOSFET, the output rectifier can also be selected.
A minimum breakdown voltage of 1.2·Vout (4) and a current rating higher than 3·Iout
(Equation 8) can be chosen for a rough, initial selection of the rectifier. The correct choice is
then confirmed by the thermal calculation. If the diode junction temperature works within
125°C the device has been correctly selected, otherwise a bigger device must be selected.
The switching losses can be significantly reduced if an ultra-fast diode is employed. Since
18/36
Doc ID 16820 Rev 3
AN3112
Designing a fixed-off-time PFC
this circuit operates in the continuous current mode, the MOSFET has to recover the boost
diode minority carrier charge at turn-on. Therefore, an ultrafast or a SiC rectifier must be
selected.
In this 400 W application an STTH8R06 (600 V, 8 A) can be selected. The STTH8R06 offers
the best solution for the continuous current mode operation due to its very fast reverse
recovery time, typically 25 ns. This part has a breakdown voltage rating (Vrrm) of 600 V,
average forward current rating (Ifave) of 8 A and reverse recovery time (trr) of 25 ns. The
rectifier AVG (Equation 8) and RMS (Equation 17) current values and the parameter Vth
(rectifier threshold voltage) and Rd (dynamic resistance) given in the datasheet allow the
calculation of the rectifier losses.
From the STTH8R06 datasheet, Vth is 1.16 V, Rd is 0.08 Ω, neglecting the recovery losses:
Equation 37
Pdiode = Vth ⋅ Iout + R d ⋅ ID 2rms Pdiode = 1.16V ⋅ 1.0A + 0.08Ω ⋅ (2.56A )2 = 1.69 W
From (13) and Equation 37 the maximum thermal resistance to keep the junction
temperature below 125°C is then:
Equation 38
R th =
125°C − 50°C
°C
= 44.45
1.69W
W
R th =
L6564 biasing circuitry
Following the dimensioning of the power components, the biasing circuitry for the L6564 is
also described here. For reference, the internal schematic of the L6564 is represented in
Figure 11. For more detail on the internal functions please refer to the datasheet.
Figure 11. L6564 internal schematic
=&'
9FF
=HUR&XUUHQW
'HWHFWRU
'LVDEOH
9
9
3)&B2.
9
9
9
293
9ROWDJH
UHIHUHQFHV
92/7$*(
5(*8/$725
«
9
9
89/2
,QWHUQDO6XSSO\%XV
89/2
/B293
6
5
4
*'
'5,9(5
&/$03
67$57(5
6WDUWHU
2))
&203
',6$%/(
'LVDEOH
9
08/7
4
/(%
4
293
212))&RQWURO
6
/B293
5
89/2
(UURU$PSOLILHU
*1'
,GHDOUHFWLILHU
9
08/7,3/,(5
&6
212))&RQWURO
9
9
0$,16'523
'(7(&725
,19
4.3.7
125°C − Tambx
P diode
9
'LVDEOH
9))
!-V
Doc ID 16820 Rev 3
19/36
Designing a fixed-off-time PFC
AN3112
Pin 1 (INV) is connected both to the inverting input of the E/A and to the OVP circuitry. A
resistive divider is connected between the boost regulated output voltage and this pin. The
internal reference on the non-inverting input of the E/A is 2.5 V (typ.), the output voltage
(Vout) of the PFC pre-regulator is set at its nominal value, by the resistors ratio of the
feedback output divider. RoutH and RoutL are then selected considering the desired
nominal output voltage and the desired output power dissipated on the output divider. For
example for a 50 mW output divider dissipation:
Equation 39
R outH =
(VOUT − 2.5V)2
(400 V − 2.5V)2
R outH =
= 3.160MΩ
50mW
50mW
With the commercial value selected RoutH = 3 MΩ:
Equation 40
R outH
V
R outH 400 V
= out − 1
=
− 1 = 159
R outL 2.5V
R outL
2 .5 V
Equation 41
RoutL =
RoutH
159
R outL =
3MΩ
= 18.8kΩ
159
RoutL = 62 kΩ in parallel to a 27 kΩ can be selected. Please note that for RoutH a resistor
with a suitable voltage rating (>400 V) is needed, or more resistors in series must be used.
Pin 6 (PFC_OK - feedback failure protection): The PFC_OK pin is dedicated to monitoring
the output voltage with a separate resistor divider. This divider is selected so that the voltage
at the pin reaches 2.5 V if the output voltage exceeds a preset value (Vovp), usually larger
than the maximum Vout that can be expected, also including worst-case load/line transients.
For a maximum output voltage Vout max of 430 V and selecting a 50 µA current flowing into
the divider:
Equation 42
RL =
VREF _ PFC _ OK
Idivider
RL =
2.5V
= 50kΩ
50µA
By selecting a commercial value of 51kΩ:
Equation 43
⎛ VOUT _ MAX
⎞
⎛ 430V ⎞
RH = RL ⋅ ⎜
− 1⎟ RH = 51kΩ ⋅ ⎜
− 1⎟ = 8.721MΩ
⎜V
⎟
⎝ 2 .5 V
⎠
⎝ REF _ PFC _ OK
⎠
Connecting in series, two 3.3 MΩ resistors and one 2.2 MΩ resistor, a total value of 8.8 MΩ
can be obtained.
Note that both feedback dividers connected to the L6564 pin #1 (INV) and pin #6 (PFC_OK)
can be selected without any constraints. The unique criterion is that both dividers must sink
20/36
Doc ID 16820 Rev 3
AN3112
Designing a fixed-off-time PFC
a current from the output bus which needs to be significantly higher than the current biasing
the error amplifier and PFC_OK comparator.
The OVP function described above can handle "normal" over-voltage conditions, that is,
those resulting from an abrupt load/line change or occurring at start-up. If the over-voltage is
generated by a feedback disconnection for instance, when one of the upper resistors of the
output divider fails to open, an additional circuitry detects the voltage drop of pin INV. If the
voltage on pin INV is lower than 1.66V (Typ.) and at same time the OVP is active, a feedback
failure is assumed.
Therefore, the gate drive activity is immediately stopped, the device is shut down, its
quiescent consumption is reduced to below 180 µA and the condition is latched as long as
the supply voltage of the IC is above the UVLO threshold. To restart the system it is
necessary to recycle the input power, so that the Vcc voltage of the L6564 goes below 6 V
and that one of the PWM controllers goes below its UVLO threshold. Note that this function
offers complete protection against feedback loop failures or erroneous settings, and also
against the failure of the protection itself. Either resistor of the PFC_OK divider failing short
or open or a PFC_OK pin floating may result in shutting down the IC and stopping the preregulator. In addition, the PFC_OK pin doubles its function as a not-latched IC disable: a
voltage below 0.23 V shuts down the IC, reducing its consumption below 2 mA. To restart
the IC, simply let the voltage at the pin go above 0.27 V.
Pin 2 (COMP): This pin is the output of the E/A that is fed into one of the two inputs of the
multiplier. A feedback compensation network is placed between this pin and the INV pin
(pin#1). It must be designed with a narrow bandwidth in order to avoid the system rejecting
the output voltage ripple (100 Hz) that would cause high distortion of the input current
waveform. A theoretical criterion to define the compensation network value is to set the E/A
bandwidth (BW) from 20 to 30 Hz.
For a more complex way of compensating the FOT PFC please refer to [1], [2], [3].
A compensated two-pole feedback network for this 400 W FOT PFC can be obtained with
the following values:
C compP = 100nF C compS = 1µF R compS = 56kΩ
(14)
to which the following open-loop transfer function and its phase function correspond.
Doc ID 16820 Rev 3
21/36
Designing a fixed-off-time PFC
AN3112
Figure 12. Open loop transfer function-bode
plot
Figure 13. Phase
-100
Phase [deg]
100
Gai n [dB]
0
-150
-100
-200
-200
0. 1
1
f [Hz]
10
100
1000
0.1
1
f [Hz]
10
100
1000
The two bode plot charts are relevant to the PFC operating at the main voltage set point of
265 Vac and full load. In this condition the crossover frequency is fc = 4 Hz, the phase
margin is 50° and the third harmonic distortion is below 3%.
Pin 4 (CS): The #4 pin is the inverting input of the current sense comparator. Through this
pin, the L6564 senses the instantaneous inductor current, converted in a proportional
voltage by an external sensing resistor (Rs). As this signal crosses the threshold set by the
multiplier output, the PWM latch is reset and the power MOSFET is turned off. The
MOSFET stays in off-state until the PWM latch is set again by the ZCD signal. The pin is
equipped with 150 ns (typ.) leading-edge blanking for improved noise immunity.
The sense resistor value (Rs) can be calculated as follows. For the 400 W PFC it is:
Equation 44
Rs <
Vcs min
IL pk max
Rs <
1. 0 V
= 0.124Ω
8.01A
Where:
●
ILpk: it is the maximum peak current in the inductor, calculated as described in 4.2
●
Vcsmin = 1.0 V, it is the minimum voltage admitted on the L6564 current sense (on the
datasheet).
Because the internal current sense clamping sets the maximum current that can flow in the
inductor, the maximum peak of the inductor current may be calculated considering the
maximum voltage Vcsmax allowed on the L6564 (on datasheet):
Equation 45
IL pksat =
Vcs max
Rs
IL pksat =
1.16V
= 9.67A
0.12Ω
The calculated ILpkx is the value at which the boost inductor must not be in saturation and it
is used for calculating the inductor number of turns and air-gap length.
22/36
Doc ID 16820 Rev 3
AN3112
Designing a fixed-off-time PFC
The power dissipated by Rs is given by:
Equation 46
2
Ps = R s ⋅ ISWrms
Ps = 0.12Ω ⋅ (4.22) = 2.14W
2
According to the result, for example four parallel resistors of 0.47 Ω with 1 W of power rating
can be selected.
Pin 3 (MULT): The MULT pin is the second multiplier input. It is connected, through a
resistive divider, to the rectified mains to obtain a sinusoidal voltage reference. The multiplier
is described by the relationship:
Equation 47
VCS = VCS _ OFFSET + k m ⋅
(VCOMP − 2.5V) ⋅ VMULT
2
VFF
Where:
●
VCS (Multiplier output) is the reference for the current sense (VCS_OFFSET is its
offset).
●
k = 0.45 (Typ.) is the multiplier gain.
●
VCOMP is the voltage on pin 2 (E/A output).
●
VMULT is the voltage on pin 3.VFF is the second input to the multiplier for 1/V^2
function. It compensates the control loop gain dependence on the mains voltage. The
voltage at this pin is a DC level equal to the peak voltage on the MULT pin (#3).
Figure 14. Multiplier characteristics family for Figure 15. Multiplier characteristics family for
VFF =1 V
VFF=3 V
A complete description is given in the diagram in Figure 14 and Figure 15 which shows the
typical multiplier characteristics family. The linear operation of the multiplier is guaranteed
within the range 0 to 3 V of VMULT and the range 0 to 1.16 V (typ.) of Vcs, while the
minimum guaranteed value of the maximum slope of the characteristics family (typ.) is:
Doc ID 16820 Rev 3
23/36
Designing a fixed-off-time PFC
AN3112
Equation 48
dVCS
V
= 1.66
dVMULT
V
The voltage on the MULT pin is also used to derive the information from the RMS mains
voltage for the VFF compensation.
Before describing the correct operating point of the multiplier for the brownout function the
voltage feed forward pin and its enable-disable property is here described:
Pin 5 (voltage feed forward): The power stage gain of PFC pre-regulators varies with the
square of the RMS input voltage. As does the crossover frequency (fc) of the overall openloop gain because the gain has a single pole characteristic. This leads to large trade-offs in
the design. For example, setting the gain of the error amplifier to get fc = 20 Hz @ 264 Vac
means having fc about 4 Hz @ 88 Vac, resulting in sluggish control dynamics. Additionally,
the slow control loop causes large transient current flow during rapid line or load changes
that are limited by the dynamics of the multiplier output. This limit is considered when
selecting the sense resistor to let the full load power pass under minimum line voltage
conditions, with some margin. But a fixed current limit allows excessive power input at high
line, whereas a fixed power limit requires the current limit to vary inversely with the line
voltage.
Voltage feed-forward can compensate for the gain variation with the line voltage and allow
the overcoming of all of the above-mentioned issues. It consists of deriving a voltage
proportional to the input RMS voltage, feeding this voltage into a squarer/divider circuit (1/V2
corrector) and providing the resulting signal to the multiplier which generates the current
reference for the inner current control loop.
In this way, a change of the line voltage causes an inversely proportional change of the halfsine amplitude at the output of the multiplier (if the line voltage doubles the amplitude of the
multiplier, output is halved and vice versa), so that the current reference is adapted to the
new operating conditions with (ideally) no need for invoking the slow dynamics of the error
amplifier. Additionally, the loop gain is constant throughout the input voltage range, which
significantly improves the dynamic behavior at low line and simplifies loop design.
Actually, with another PFC embedding the voltage feed-forward, deriving a voltage
proportional to the RMS line voltage implies a form of integration, which has its own time
constant. If it is too small the voltage generated may be affected by a considerable amount
of ripple at twice the mains frequency which causes distortion to the current reference
(resulting in high THD and poor PF); if it is too large there may be a considerable delay in
setting the right amount of feed-forward, resulting in excessive overshoot and undershoot of
the pre-regulator's output voltage in response to large line voltage changes. Clearly a tradeoff was required.
The L6564 produces an innovative voltage feed-forward which, with a technique that makes
use of just two external parts, overcomes this time constant trade-off issue regardless of
which voltage change occurs on the mains, both surges and drops. A capacitor CFF and a
resistor RFF, both connected from the VFF pin (pin #5) to ground, complete an internal
peak-holding circuit that provides a DC voltage equal to the peak of the rectified sine-wave
applied on the MULT pin (pin #3). In this case the following value has been selected:
CFF = 1µF
24/36
Doc ID 16820 Rev 3
RFF = 1MΩ
(15)
AN3112
Designing a fixed-off-time PFC
In this way, in the case of a sudden line voltage rise, CFF is rapidly charged through the low
impedance of the internal diode; in case of line voltage drop, an internal mains drop detector
enables a low impedance switch which suddenly discharges CFF, avoiding long settling time
before reaching the new voltage level. Consequently an acceptably low steady-state ripple
and low current distortion can be achieved without any considerable undershoot or
overshoot on the pre-regulator's output, like in systems with no feed-forward compensation
This pin is internally connected to a comparator in order to provide the brownout (AC mains
undervoltage) protection. A voltage below 0.8 V shuts down (not latched) the IC and brings
its consumption to a considerably lower level. The IC restarts when the voltage at the pin
rises above 0.88 V. These details must be taken into account during the MULT divider
selection.
The suggested procedure to properly set the operating point of the multiplier is now
described. First, the maximum peak value for VMULT, VMULTmax is selected. This value,
which occurs at maximum mains voltage, should be 3 V or thereabouts in wide range mains
and less in single mains. The sense resistor selected is Rs = 0.12 Ω and it is described in
the pin 4 section. According to the L6564 datasheet and to the linearity setting of the pin, the
maximum voltage on the multiplier input is:
VMULTmax = 3V
(16)
From (16) the maximum required divider ratio is calculated as:
Equation 49
kp =
VMULT max
2 ⋅ VACmax
=
3.00V
2 ⋅ 265 Vac
= 8 ⋅ 10 − 3
Supposing a 60 µA current flowing into the multiplier divider the lower resistor value can be
calculated:
Equation 50
RmultL =
VMULT max 3.00V
=
= 50kΩ
60µA
60µA
A commercial value of 51 kΩ for the lower resistor is selected. The upper resistor value can
now be calculated:
Equation 51
RmultH =
1− k p
kp
RmultL =
1 − 8 ⋅ 10 −3
8 ⋅ 10 −3
51kΩ = 6.319MΩ
In this example a RmultH = 6.9 MΩ and a RmultL = 51 kΩ can be selected. For RmultH a
resistor with a suitable voltage rating (>400 V) is needed, or more resistors in series must be
used.
The voltage on the multiplier pin with the selected component values re-calculated at
minimum line voltage is 0.93 V and at maximum line voltage is 2.74 V. So the multiplier
works correctly within its linear region.
Doc ID 16820 Rev 3
25/36
Designing a fixed-off-time PFC
AN3112
Because the MULT divider also determines the mains input voltage at which the PFC starts
and stops (brownout function), these values are calculated using the actual divider ratio:
Equation 52
VSTART ==
0.88V RmultH + RmultL
0.88V 6.9MΩ + 51kΩ
⋅
VSTART =
⋅
= 84.8V
RmultL
51kΩ
2
2
And also the stop voltage:
Equation 53
VSTOP ==
0.80 V RmultH + RmultL
⋅
RmultL
2
VSTOP =
0.80V 6.9MΩ + 51kΩ
⋅
= 77.1V
51kΩ
2
Start and stop PFC mains voltage are compatible with the input mains voltage range (1).
In order to obtain the required startup and shutdown voltage, a reiteration may be required,
by selecting MULT resistors and checking the actual PFC start and stop mains voltage.
Pin 7 (ZCD): This is the input of the zero current detector circuit. In FOT mode, it is
connected to the line-modulated fixed-off-time circuit seen in Figure 6. Taking into account
the information in Section 3: Implementing the line-modulated fixed-off-time, the starting
point for the design of that circuit is the pair of the desired values for TOFF on the top of the
line voltage sinusoid at minimum (TOFF @VACmin) and maximum line (TOFF @VACmax)
obtained by setting the switching frequency on the peak of the sinusoid at low mains and
considering the minimum on-time of the L6564:
Equation 54
TOFF (VACmin ) =
k min
fsw min
TOFF (VACmin ) =
0.32
− 220ns = 3.76µs
80kHz
Equation 55
TOFF (VAC max ) =
TON min ⋅ k max
1 − k max
TOFF (VAC max ) =
450ns ⋅ 0.94
− 220ns = 6.1µs
1 − 0.94
Where Fswmin is the switching frequency on top of the sinusoid of the input voltage at
VACmin = 90 Vac (Figure 16) and 220 ns is a corrector factor in order to consider the delay
between the ZCD and GD signal.
Considering the ratio between Equation 55, Equation 54, we have:
Equation 56
ρx =
TOFF (VACmax )
TOFF (VACmin )
ρx =
6.1µs
= 1.63
3.76µs
In the formula, Equation 55 and Equation 54, the delay between the ZCD signal and the
gate drive signal is taken into account in order to increase the accuracy of the mathematical
model.
26/36
Doc ID 16820 Rev 3
AN3112
Designing a fixed-off-time PFC
From the theory of the line modulation fixed off-time, TOFF increases with the line voltage so
that at maximum line voltage the condition TON>TONmin [4] is always true. This is important
in order to avoid line distortion [5].
Figure 16. Switching frequency function on the peak of the sinusoid input voltage
waveform and the corresponding off- time value
Now considering the two discharging resistors R and R0 of the circuit in Figure 6, the ratio is
defined as:
Equation 57
K1 =
R
R0 + R
where 0 < K1 < 1. Through the definition of the k2 parameter the expected time constant
τ =(R//R0)C is underlined, necessary for achieving the desired TOFF@90 Vac.
Equation 58
K2 =
TOFF (VACmin )
τ
Finding a way to obtain K1 and K2 means to gain the values of R and R0 and the
discharging time constant of the capacitor C.
The following section describes the mathematical way of obtaining the two parameters K1
and K2. Combining Equation 56, Equation 57, Equation 58 with the expression of the offtime (Equation 5), the following expressions are obtained:
Doc ID 16820 Rev 3
27/36
Designing a fixed-off-time PFC
AN3112
Equation 59
1−k
⎡ ⎡
⎤ 1
⎤
⎡
VACmax
⎛
⎢ ⎢
⎥
+ VF ⎥ ⋅ (1 − k 1)
⎜
⎢Vmult min ⋅
⎢ ⎢
VZCDtrigger
VAC
⎥
min
⎦
⎣
⎜
⎢ln⎢
+
ln
⎥
⎜
VACmax
⎡
⎤⎤
⎢ ⎢⎡
VAC max
+ VF
⎜ Vmult min ⋅
+ VF ⎥ ⎥ ⋅ (k 1) ⎥
⎢ ⎢ ⎢VZCDclamp − ⎢Vmult min ⋅ VAC
VAC
⎥
min
⎝
min
⎣
⎦ ⎦⎥
⎢ ⎣ ⎣⎢
⎦
ρ(Vmult min , k 1) = ⎣
1−k
⎡ ⎡
⎤ 1
⎛ VZCDtrigger ⎞⎤⎥
[Vmult min + VF ]⋅ (1 − k1)
⎢ln⎢
⎜
⎟
+
ln
⎥
⎜V
⎟
⎢ ⎣⎢ VZCDclamp − [Vmult min + VF ] ⋅ (k 1) ⎦⎥
mult min + VF ⎠ ⎥
⎝
⎣
⎦
[
⎤
⎞⎥
⎟⎥
⎟⎥
⎟⎥
⎟⎥
⎠⎥
⎦
]
Equation 60
1−k
⎡
⎡
⎤ 1
⎛ VZCDtrigger
[
Vmult min + VF ]⋅ (1 − k 1)
−1
⎢
⋅ ln⎢
k 2 (Vmult min , k 1) =
+ ln⎜⎜
⎥
⎢1 − k 1 ⎢ VZCDclamp − [Vmult min + VF ]⋅ k 1 ⎥
⎝ Vmult min + VF
⎣
⎦
⎣
⎞⎤⎥
⎟
⎟⎥
⎠⎦
From Equation 56 and Equation 59, solving the following equation:
Equation 61
ρ(Vmult min , k 1) − ρ x = 0 K1 = 0.903
And then substituting K1 value into the Equation 60 expression, the k2 parameters are
obtained:
Equation 62
K 2 = k 2 (Vmult min , k 1) K 2 = 11.17
From the values of K1 and K2 it is possible to calculate the time constant τ =(R1//R2) C
necessary to achieve the desired TOFF@90 Vac:
Equation 63
τ=
TOFF (VACmin )
K2
τ=
3.76µs
= 336.35ns
11.17
Now, by selecting a capacitor C in the hundred picofarad range or a few nanofarads, for
example a C =220 pF, it is possible to determine the required equivalent resistance value:
Equation 64
Req =
336.35ns
τ
Req =
= 1.53kΩ
220pF
C
From Equation 57 R and R0 are found:
28/36
Doc ID 16820 Rev 3
AN3112
Designing a fixed-off-time PFC
Equation 65
R=
Req
1 − K1
R=
1.53kΩ
= 15.79kΩ
1 − 0.903
Equation 66
R0 =
R eq
K1
R0 =
1.53kΩ
= 1.5kΩ
0.903
A commercial value R = 15 kΩ and a R0 = 1.5 kΩ has been chosen.
Figure 17 and Figure 18 show the trend of the off-time and the switching frequency vs the
input mains voltage. The PFC inner current loop works in the range of 80 kHz-150 kHz.
Due to the tolerance of the capacitor selected (C) and the two discharging resistors, it is
important to take into account a variation on the switching frequency in a real board of about
± 10%.
Figure 17. Off-time vs. input mains voltage
Figure 18. Switching frequency vs. input
mains voltage
Finally the Rs limiting resistor should be selected according to the inequalities (Equation 6):
Equation 67
10V − 5.7V − 0.6V
15V − 5.7V − 0.6V
< Rs < 1.53kΩ ⋅
5. 7 V
5 .7 V
10mA +
1.53kΩ
and the speed-up capacitor Cs using Equation 7.
Equation 68
Cs < 220pF ⋅
5 .7 V
15V − 5.7V − 0.6V
This means that after calculations:
Doc ID 16820 Rev 3
29/36
Designing a fixed-off-time PFC
AN3112
Equation 69
726Ω < Rs < 1kΩ
Equation 70
Cs < 144pF
For example, a commercial value of the limiting resistor of 1 kΩ and a speed-up capacitor of
100 pF can be selected for this application.
Pin 8 (GND) acts as the current return both for the signal internal circuitry and for the gate
drive current. When laying out the printed circuit board, these two paths should run
separately.
Pin 9 (GD) is the output of the driver. The pin is able to drive an external MOSFET with
600 mA source and 800 mA sink capability.
The high-level voltage of this pin is clamped at about 12 V to avoid excessive gate voltages
if the pin is supplied with a high Vcc. To avoid undesired switch-on of the external MOSFET
because of some leakage current when the supply of the L6564 is below the UVLO
threshold, an internal pull-down circuit holds the pin low. The circuit guarantees 1.1 V
maximum on the pin (@ Isink = 2 mA), with VCC > VCC_ON. This allows the omitting of the
bleeder-resistor connected between the gate and the source of the external MOSFET used
to this purpose.
Pin 10 (Vcc) is the supply of the device which is externally connected to the start-up circuit
(usually, one resistor connected to the rectified mains) and to the self-supply circuit.
Whatever the configuration of the self-supply system, a capacitor is connected between this
pin and ground.
To start the L6564, the voltage must exceed the start-up threshold (12 V typ.). Below this
value the device does not
and consumes less than 90 µA (typ.) from Vcc. This allows the use of high value start-up
resistors (in the hundreds kΩ), which reduces power consumption and optimizes system
efficiency at low load, especially in wide range mains applications.
When operating, the current consumption (of the device only, not considering the gate drive
current) rises to a value depending on the operating conditions but never exceeding 6 mA.
The device continues to work as long as the supply voltage is over the UVLO threshold (13
V max). If the Vcc voltage exceeds 22.5 V an internal zener diode, 20 mA rated, is activated
in order to clamp the voltage. Please remember that during normal operation the internal
zener doesn’t have to clamp the voltage, because in this case the power consumption of the
device increases considerably and its junction temperature also increases. The suggested
operating condition, for safe operation of the device, is below the minimum clamping voltage
of the pin.
30/36
Doc ID 16820 Rev 3
Design example using the L6564-FOT PFC Excel® spreadsheet
AN3112
5
Design example using the L6564-FOT PFC Excel®
spreadsheet
An Excel spreadsheet has been developed to allow a quick and easy design of a boost PFC
pre-regulator using the STMicroelectronics L6564 controller, operating in fixed-off-time.
Figure 21 shows the first sheet precompiled with the input design data used in Section 4:
Designing a fixed-off-time PFC.
Figure 19. Excel spreadsheet design specification input table
Figure 20. Other design data
The tool is able to generate a complete parts list of the PFC schematic represented in
Figure 21, including the power dissipation calculation of the main components.
Doc ID 16820 Rev 3
31/36
Design example using the L6564-FOT PFC Excel® spreadsheet
AN3112
Figure 21. Excel spreadsheet FOT PFC schematic
The bill of material in Figure 21 is automatically compiled by the Excel spreadsheet.
It summarizes all the selected components and some salient data.
32/36
Doc ID 16820 Rev 3
Design example using the L6564-FOT PFC Excel® spreadsheet
AN3112
Figure 22. Excel spreadsheet BOM
400 W FOT PFC BASED ON L6564
BILL OF MATERIAL
Selected
Value
Unit
[]
µH
BRIDGE RECTIFIER
D15XB60
MOSFET P/N
2 x STP12NM50PF
DIODE P/N
STTH8R06
Inductor
Max peak Inductor current
L
Ilpkx
500
9.67
Sense resistor
Power dissipation
Rsx
Ps
0.12
2.14
W
INPUT Capacitor
Cin
1
µF
OUTPUT Capacitor
Cout
330
µF
Pin3 - MULT Divider
Rmult L
Rmult H
51
6900
kΩ
kΩ
ZCD FOT circuit
Rzcd1
Rzcd2
Rzcd3
Czcd1
Czcd2
15
1
1.5
220
100
kΩ
kΩ
kΩ
pF
pF
Diode P/N
pnp-BJT P/N
1N4148
BC857C
Feedback Divider
RoutH
RoutL
3000
18.8
kΩ
kΩ
RL
RH
51
8800
kΩ
kΩ
Compensation Network
CcompP
CcompS
RcompS
100
1000
56
nF
nF
kΩ
Voltage Feedforward
CFF
RFF
1000
1000
nF
kΩ
IC Controller
L6564
Output divider for
PFC_OK
Doc ID 16820 Rev 3
A
Ω
33/36
Reference
6
AN3112
Reference
1.
2.
3.
4.
5.
6.
7.
34/36
A new continuous-time model for current-mode control with constant frequency,
constant on-time and constant off-time, in CCM and DCM”, IEEE power electronics
specialists conference record, San Antonio, Texas, pp. 382-389, 1990
“Current mode control”, venable technical paper #5, www.venableind.com
“Fixed-off-time control of PFC pre-regulators”, 10th European conference on power
electronics and applications, EPE2003, Toulouse, France, paper 382
“L6564, transition-mode PFC controller”, datasheet, www.st.com
“Design fixed-off-time-controlled PFC pre-regulators with the L6562”, AN1792
“400W FOT-controlled PFC pre-regulator with the L6563”, AN2485
“A systematic approach to frequency compensation of the voltage loop in boost PFC
pre-regulator”, abstract
Doc ID 16820 Rev 3
AN3112
7
Revision history
Revision history
Table 1.
Document revision history
Date
Revision
Changes
03-May-2010
1
Initial release.
02-Dec-2010
2
Updated: Section 4.3.7 on page 19.
09-Feb-2011
3
Updated: Figure 11 on page 19.
Doc ID 16820 Rev 3
35/36
AN3112
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2011 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
36/36
Doc ID 16820 Rev 3