Anaren MSK5173HL 1.5a, negative adjustable linear regulator Datasheet

MIL-PRF-38534 AND 38535 CERTIFIED FACILITY
1.5A, NEGATIVE
ADJUSTABLE
LINEAR REGULATOR
FEATURES:
5173
SMD-1
3 PAD
CERAMIC
Output Current Limit
Internal Thermal Overload Protection
Output Current to 1.5 Amps
Adjustable Output using two External Resistors
Available in 3 Lead Form Options: Straight, Up and Down (TO-257)
Electrically Isolated Package (TO-257)
Equivalent Rad Hard Device MSK5973RH
Contact MSK for MIL-PRF-38534 Qualification Status
TO-257
DESCRIPTION:
The MSK5173 is a 3-terminal negative adjustable regulator capable of supplying up to 1.5A of current. The output is
adjustable using external resistors for a range of Vref to -27V. Excellent line and load regulation characteristics ensure accurate performance. The MSK5173 has full protection with current and thermal limiting. The MSK5173 is packaged in two
space saving packages, the 3 pin power surface mount ceramic SMD-1 or the TO-257 package with 3 lead form options:
straight, up and down.
EQUIVALENT SCHEMATIC
PIN-OUT INFORMATION
TYPICAL APPLICATIONS
TO-257
System Power Supplies
Switching Power Supply Post Regulators
Constant Voltage/Current Regulators
High Efficiency Linear Regulators
1
2
3
ADJ
VIN
VOUT
SMD-1
1 ADJ
2 VOUT
3 VIN
PACKAGE=ISOLATED
1
8548-85 Rev. D 1/16
ABSOLUTE MAXIMUM RATINGS
VIN
PD
IOUT
TJ
Input Voltage (VIN-VOUT)
Power Dissipation
Output Current
Junction Temperature
8
TST
TLD
30VDC
Internally Limited
1.5A
+150°C
TC
Storage Temperature Range
Lead Temperature Range
(10 Seconds)
Case Operating Temperature
MSK5173
MSK5173H
9
-65°C to +150°C
300°C
-55°C to +125°C
-55°C to +125°C
ELECTRICAL SPECIFICATIONS
NOTES:
1 Output is decoupled to ground using 10µF low ESR tantalum capacitors and 0.1µF ceramic.
2 Guaranteed by design but not tested. Typical parameters are representative of actual device
performance but are for reference only.
3 All output parameters are tested using a low duty cycle pulse to maintain TJ = TC.
4 Industrial grade and devices shall be tested to subgroup 1 unless otherwise specified.
5 Military grade devices ("H" suffix) shall be 100% tested to subgroups 1,2 and 3.
6 Subgroup 1 TA=TC=+25°C
Subgroup 2 TA=TC=+125°C
Subgroup 3 TA=TC=-55°C
7 The output current limit function provides protection from transient overloads but it may exceed the maximum continuous rating.
Continuous operation in current limit may damage the device.
8 Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle.
9 Internal solder reflow temperature is 180°C, do not exceed.
2
8548-85 Rev. D 1/16
APPLICATION NOTES
OUTPUT VOLTAGE
LOAD REGULATION
The MSK5173 develops a nominal -1.25V reference voltage between the output and adjustment terminal. With a constant reference voltage drop across program resistor R1, a constant current
flows through the output set resistor R2. Since the current from the
adjustment terminal represents an error in the programmed output
voltage, the MSK5173 was designed to minimize IADJ and make it
very constant with line and load changes. To do this, all quiescent
operating current is returned to the output establishing a minimum
load current requirement. If there is insufficient load on the output,
the output will rise. Figure 1 shows the output voltage calculations.
The MSK5173 is capable of providing extremely good load regulation
but a few precautions are needed to obtain maximum performance.
The current set resistor connected between the adjustment terminal
and the output terminal should be tied directly to the output pin as
close to the case of the regulator as possible rather than near the
load. This eliminates package pin and trace drops from appearing
effectively in series with the reference and degrading regulation.
For example, if the regulator is set to -5V with 0.05Ω resistance
between the regulator and the current set resistor, the output will
droop 225mV at 1A due to package pin and trace resistance. The
amount of droop can be calculated as follows: (VOUT at 5mA) (1.250-(0.05Ω*IL))*(1+R2/R1). The ground of R2 can be returned
near the ground of the load to provide remote ground sensing and
improve load regulation. Figure 2A shows the effect of resistance
between the regulator and 240Ω set resistor.
FIGURE 1
INPUT VOLTAGE
FIGURE 2A
(Degraded Regulation)
The minimum required input voltage for proper operation is VOUT+
Dropout voltage. See typical performance curves for
dropout performance.
EXTERNAL CAPACITORS
Input bypassing with a 1uF tantalum in parallel with a 0.1uF ceramic
on the input is suitable in most applications. To maximize transient
response and minimize input supply transients more input capacitance can be added. The adjustment terminal can be bypassed to
ground on the MSK5173 to improve ripple rejection. This bypass
capacitor prevents ripple from being amplified at higher output
voltages. The impedance of the adjust pin capacitor at the ripple
frequency should be less than the value of R1. For most application
a 10µF bypass capacitor will provide sufficient ripple rejection at any
output level. Increases over 10µF do not appreciably improve the
ripple rejection at frequencies above 120Hz. Output bypassing with
10µF low ESR tantalum in parallel with a 0.1µF ceramic attached as
close to the regulator's output as possible is best. This will effectively
lower the regulator output impedance, increase transient response
and eliminate any oscillations. Any increase of the load capacitance
larger than 10µF will merely improve the loop stability and output
impedance. See Figure 3 for typical application schematic.
FIGURE 2B
(Best Case Regulation)
3
8548-85 Rev. D 1/16
APPLICATION NOTES CONT'D
PROTECTION DIODES
HEAT SINKING
When external capacitors are used with any IC regulator it is sometimes necessary to add protection diodes to prevent the capacitors
from discharging through low current points into the regulator. Most
10µF capacitors have low enough internal series resistance to deliver 20A spikes when shorted. Although the surge is short, there
is enough energy to stress MSK5173. When an output capacitor
is connected to a regulator and the input is shorted or crowbarred,
the output capacitor will discharge into the output of the regulator.
The discharge current depends on the value of the capacitor, the
output voltage of the regulator, and the rate of decrease of VIN.
Figure 3 shows an MSK5173 with protection diodes included. D2
is only required if the adjust pin has external capacitance tied to it .
To determine if a heat sink is required for your application and if so,
what type, refer to the thermal model and governing equation below.
Governing Equation: Tj = Pd x (Rθjc + Rθcs + Rθsa) + Ta
WHERE
Tj = Junction Temperature
Pd = Total Power Dissipation
Rθjc= Junction to Case Thermal Resistance
Rθcs= Case to Heat Sink Thermal Resistance
Rθsa = Heat Sink to Ambient Thermal Resistance
Tc = Case Temperature
Ta = Ambient Temperature
Ts = Heat Sink Temperature
EXAMPLE:
This example demonstrates an analysis with the output set to
-10V, where the output current is at 0.5 amp and the input is -15V.
Conditions for MSK5173:
VIN = -15V; Iout = 0.5A
1.) Assume 45° heat spreading model.
2.) Find regulator power dissipation:
Pd = (VIN - VOUT)(Iout)
Pd = (15V-10V)(0.5A)
Pd = 2.5W
FIGURE 3
3.) For conservative design, set Tj = +125°C Max.
4.) For this example, worst case Ta= +90°C.
5.) Rθjc = 6.7°C/W from the Electrical Specification Table.
6.) Rθcs= 0.15°C/W for most thermal greases.
7.) Rearrange governing equation to solve for Rθsa:
Rθsa=((Tj - Ta)/Pd) - (Rθjc) - (Rθcs)
= (125°C-90°C)/2.5W - 6.7°C/W - 0.15°C/W
= 7.2°C/W
In this case the result is 7.2°C/W. Therefore, a heat sink with a
thermal resistance of no more than 7.2°C/W must be used in this
application to maintain regulator circuit junction temperature under
125°C.
4
8548-85 Rev. D 1/16
TYPICAL PERFORMANCE CURVES
5
8548-85 Rev. D 1/16
MECHANICAL SPECIFICATIONS
ESD TRIANGLE INDICATES PIN 1
WEIGHT=3.2 GRAMS TYPICAL
MSK5173 H U
ALL DIMENSIONS ARE SPECIFIED IN INCHES
ORDERING INFORMATION
LEAD CONFIGURATIONS
S= STRAIGHT; U= BENT UP; D= BENT DOWN
SCREENING
BLANK= INDUSTRIAL; H=MIL-PRF-38534 CLASS H;
GENERAL PART NUMBER
The above example is a Class H regulator with leads bent up.
6
8548-85 Rev. D 1/16
MECHANICAL SPECIFICATIONS
ALL DIMENSIONS ARE SPECIFIED IN INCHES
WEIGHT=2.2 GRAMS TYPICAL
ORDERING INFORMATION
MSK5173 H L
3 PAD CERAMIC SMD-1 PACKAGE
SCREENING
BLANK= INDUSTRIAL; H=MIL-PRF-38534 CLASS H;
GENERAL PART NUMBER
The above example is a Class H regulator in the 3 Pad Ceramic Package.
7
8548-85 Rev. D 1/16
REVISION HISTORY
MSK
www.anaren.com/msk
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make
changes to its products or specifications without notice, however, and assumes no liability for the use of its products.
Please visit our website for the most recent revision of this datasheet.
Contact MSK for MIL-PRF-38534 qualification status.
8
8548-85 Rev. D 1/16
Similar pages