Kingbright APGA1602SEC Ideal for backlight and indicator Datasheet

1.6x0.2mm RIGHT ANGLE SMD CHIP LED
LAMP
Part Number: APGA1602SEC/E/KA
Hyper Red
Features
Description
z 1.6mmx0.2mm right angle SMT LED,0.2mm thickness.
The Hyper Red source color devices are made with Al-
z Low power consumption.
GaInP on GaAs substrate Light Emitting Diode.
z Wide viewing angle.
z Ideal for backlight and indicator.
z Moisture sensitivity level : level 3.
z Package :2000pcs / reel.
z Tinned pads for improved solderability.
z RoHS compliant.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.004") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAN2008
REV NO: V.2A
DATE: APR/22/2015
PAGE: 1 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Q.M.Chen
ERP: 1203013775
Selection Guide
Part No.
Dice
APGA1602SEC/E/KA
Iv (mcd) [2]
@ 20mA
Lens Type
Hyper Red (AlGaInP)
Viewing
Angle [1]
Min.
Typ.
2θ1/2
80
200
*55
*120
150°(H)
120°(V)
Water Clear
Notes:
1. θ1 / 2 is the angle from optical centerline where the luminous intensity is 1 / 2 of the optical peak value.
2. Luminous intensity / luminous Flux: + / -15%.
* Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
λpeak
Peak Wavelength
Hyper Red
λD [1]
Dominant Wavelength
Δλ1/2
Max.
Units
Test Conditions
632
nm
IF=20mA
Hyper Red
624
nm
IF=20mA
Spectral Line Half-width
Hyper Red
20
nm
IF=20mA
VF [2]
Forward Voltage
Hyper Red
2.05
2.4
V
IF=20mA
IR
Reverse Current
Hyper Red
10
uA
VR=5V
Notes:
1. Wavelength: + / -1nm.
2. Forward Voltage: + / -0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Hyper Red
Units
Power dissipation
48
mW
DC Forward Current
20
mA
Peak Forward Current [1]
100
mA
5
V
Reverse Voltage
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +100°C
Note:
1. 1 / 10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAN2008
REV NO: V.2A
DATE: APR/22/2015
PAGE: 2 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Q.M.Chen
ERP: 1203013775
Hyper Red
APGA1602SEC/E/KA
SPEC NO: DSAN2008
REV NO: V.2A
DATE: APR/22/2015
PAGE: 3 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Q.M.Chen
ERP: 1203013775
APGA1602SEC/E/KA
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAN2008
REV NO: V.2A
DATE: APR/22/2015
PAGE: 4 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Q.M.Chen
ERP: 1203013775
PACKING & LABEL SPECIFICATIONS
APGA1602SEC/E/KA
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAN2008
REV NO: V.2A
DATE: APR/22/2015
PAGE: 5 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Q.M.Chen
ERP: 1203013775
Similar pages