TI1 LMV791MK/NOPB 17-mhz, low-noise, cmos input, 1.8-v operational amplifier Datasheet

Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
LMV791, LMV792
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
LMV79x 17-MHz, Low-Noise, CMOS Input, 1.8-V Operational Amplifiers With Shutdown
1 Features
3 Description
Typical 5-V Supply, Unless Otherwise Noted
1
•
•
•
•
•
•
•
•
•
Input Referred Voltage Noise 5.8 nV/√Hz
Input Bias Current 100 fA
Unity Gain Bandwidth 17 MHz
Supply Current per Channel Enable Mode
– LMV791 1.15 mA
– LMV792 1.30 mA
Supply Current per Channel in Shutdown Mode
0.02 µA
Rail-to-Rail Output Swing
– At 10-kΩ Load, 25 mV from Rail
– At 2-kΩ Load, 45 mV from Rail
Ensured 2.5-V and 5-V Performance
Total Harmonic Distortion 0.01% at1 kHz, 600 Ω
Temperature Range −40°C to 125°C
2 Applications
•
•
•
•
•
The LMV791 (single) and the LMV792 (dual) lownoise, CMOS input operational amplifiers offer a low
input voltage noise density of 5.8 nV/√Hz while
consuming only 1.15 mA (LMV791) of quiescent
current. The LMV791 and LMV792 are unity gain
stable operational amplifiers and have gain bandwidth
of 17 MHz. The LMV79x have a supply voltage range
of 1.8 V to 5.5 V and can operate from a single
supply. The LMV79x each feature a rail-to-rail output
stage capable of driving a 600-Ω load and sourcing
as much as 60 mA of current.
The LMV79x family provides optimal performance in
low-voltage and low-noise systems. A CMOS input
stage, with typical input bias currents in the range of
a few femtoamperes, and an input common-mode
voltage range which includes ground, make the
LMV791 and the LMV792 ideal for low-power sensor
applications. The LMV79x family has a built-in enable
feature which can be used to optimize power
dissipation in low power applications.
The LMV791x are manufactured using TI’s advanced
VIP50 process and are offered in a 6-pin SOT and a
10-pin VSSOP package respectively.
Photodiode Amplifiers
Active Filters and Buffers
Low-Noise Signal Processing
Medical Instrumentation
Sensor Interface Applications
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
LMV791
SOT (6)
2.90 mm × 1.60 mm
LMV792
VSSOP (10)
3.00 mm × 3.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Photodiode Transimpedance Amplifier
Low-Noise CMOS Input
CF
100
+
V = 5.5V
IIN
CCM
CD
VB
+
+
VOUT
CIN = CD + CCM
VOUT
= - RF
IIN
VOLTAGE NOISE (nV/ Hz)
RF
V+ = 2.5V
10
1
1
10
100
1k
10k
100k
FREQUENCY (Hz)
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LMV791, LMV792
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
6.7
4
4
4
4
5
6
8
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
2.5-V Electrical Characteristics ................................
5-V Electrical Characteristics ...................................
Typical Characteristics ..............................................
Detailed Description ............................................ 16
7.1 Overview ................................................................. 16
7.2 Functional Block Diagram ....................................... 16
7.3 Feature Description................................................. 16
7.4 Device Functional Modes........................................ 17
8
Application and Implementation ........................ 19
8.1 Application Information............................................ 19
8.2 Typical Applications ............................................... 19
9 Power Supply Recommendations...................... 24
10 Layout................................................................... 24
10.1 Layout Guidelines ................................................. 24
10.2 Layout Example .................................................... 24
11 Device and Documentation Support ................. 25
11.1
11.2
11.3
11.4
11.5
11.6
11.7
Device Support ....................................................
Documentation Support .......................................
Related Links ........................................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
25
25
25
25
25
25
26
12 Mechanical, Packaging, and Orderable
Information ........................................................... 26
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision F (March 2013) to Revision G
Page
•
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
•
Updated the format of the Enable and Shutdown Pin Voltage Range in the 2.5-V Electrical Characteristics table for
clarity ...................................................................................................................................................................................... 5
•
Updated the format of the Enable and Shutdown Pin Voltage Range in the 5-V Electrical Characteristics table for clarity . 7
Changes from Revision E (March 2013) to Revision F
•
2
Page
Changed layout of National Data Sheet to TI format ........................................................................................................... 23
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
LMV791, LMV792
www.ti.com
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
5 Pin Configuration and Functions
LMV791 DDC Package
6-Pin SOT
Top View
6
1
OUTPUT
+
V
5
V
-
EN
2
+
-
4
3
+IN
-IN
Pin Functions—LMV791
PIN
NAME
NO.
I/O
DESCRIPTION
EN
5
I
Enable
+IN
3
I
Noninverting Input
–IN
4
I
Inverting Input
Out
1
O
Output
V+
6
P
Positive (highest) Supply Voltage
V–
2
P
Negative (lowest) Supply Voltage
LMV792 DGS Package
10-Pin VSSOP
Top View
1
10
2
9
-
IN A-
OUT B
+
3
V
-
EN A
8
+
IN B-
-
IN A+
+
V
OUT A
4
7
5
6
IN B+
EN B
Pin Functions—LMV792
PIN
I/O
DESCRIPTION
5
I
Enable A
6
I
Enable B
IN A+
3, 7
I
Inverting Input
IN A–
NAME
NO.
EN A
EN B
2, 8
I
Noninverting Input
Out
1
O
Output B
Out B
9
O
Output B
V+
10
P
Positive (highest) Supply Voltage
V–
4
P
Negative (lowest) Supply Voltage
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
3
LMV791, LMV792
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
(1) (2)
See
MIN
VIN differential
MAX
UNIT
±0.3
V
6
V
−
+
Supply voltage (V – V )
V− − 0.3
V
150
°C
Infrared or convection (20 sec)
235
°C
Wave soldering lead temperature (10 sec)
260
°C
150
°C
V+ + 0.3
Input/Output pin voltage
Junction temperature (3)
Soldering
information
−65
Storage temperature, Tstg
(1)
(2)
(3)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
The maximum power dissipation is a function of TJ(MAX), θJA. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(MAX) - TA)/θJA. All numbers apply for packages soldered directly onto a PCB.
6.2 ESD Ratings
VALUE
Electrostatic
discharge
V(ESD)
(1)
(2)
(3)
(4)
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) (2)
±2000
Charged-device model (CDM), per JEDEC specification JESD22-C101 (3)
±1000
Machine model (4)
±200
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
Human Body Model is 1.5 kΩ in series with 100 pF.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
Machine Model is 0 Ω in series with 200 pF
6.3 Recommended Operating Conditions
MIN
MAX
UNIT
−40
125
°C
2
5.5
V
1.8
5.5
V
Temperature (1)
Supply voltage
(V+ – V−)
(1)
−40°C ≤ TJ ≤ 125°C
0°C ≤ TJ ≤ 125°C
The maximum power dissipation is a function of TJ(MAX), θJA. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(MAX) - TA)/θJA. All numbers apply for packages soldered directly onto a PCB.
6.4 Thermal Information
THERMAL METRIC (1)
LMV791
LMV792
DDC (SOT-23)
DGS (VSSOP)
UNIT
6 PINS
10 PINS
RθJA
Junction-to-ambient thermal resistance (2)
191.8
179.1
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
68.1
70.5
°C/W
RθJB
Junction-to-board thermal resistance
36.9
99.7
°C/W
ψJT
Junction-to-top characterization parameter
2.2
11.6
°C/W
ψJB
Junction-to-board characterization parameter
36.5
98.2
°C/W
(1)
(2)
4
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
The maximum power dissipation is a function of TJ(MAX), θJA. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(MAX) - TA)/θJA. All numbers apply for packages soldered directly onto a PCB.
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
LMV791, LMV792
www.ti.com
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
6.5 2.5-V Electrical Characteristics
Unless otherwise specified, all limits are ensured for TJ = 25°C, V+ = 2.5 V, V− = 0 V, VCM = V+/2 = VO, VEN = V+.
PARAMETER
VOS
Input offset voltage
TC VOS
Input offset voltage temperature drift
IB
Input bias current
TEST CONDITIONS
MIN (1)
TJ = 25 °C
Input offset current
CMRR
PSRR
Common-mode rejection ratio
Power supply rejection ratio
Common-mode voltage range
LMV791 (3)
−1
LMV792 (3)
−1.8
VCM = 1 V (4)
(5)
0.05
−40°C ≤ TJ ≤ 125 °C
100
0 V ≤ VCM ≤ 1.4 V
2.0V ≤ V+ ≤ 5.5V, VCM = 0
V
TJ = 25 °C
80
−40°C ≤ TJ ≤ 125°C
75
TJ = 25 °C
80
−40°C ≤ TJ ≤ 125°C
75
fA
94
dB
80
100
dB
98
CMRR ≥ 60 dB
TJ = 25 °C
−0.3
1.5
CMRR ≥ 55 dB
−40°C ≤ TJ ≤ 125°C
−0.3
1.5
Open-loop voltage gain
LMV792
Output voltage swing high
+
RLOAD = 10 kΩ to V /2
VOUT
+
RLOAD = 2 kΩ to V /2
Output voltage swing low
RLOAD = 10 kΩ to V+/2
−
Sourcing to V
VIN = 200 mV (6)
Output current
+
Sinking to V
VIN = –200 mV (6)
Enable mode
VEN ≥ 2.1 V
Supply current per amplifier
Shutdown mode, VEN <
0.4
per channel
TJ = 25 °C
85
−40°C ≤ TJ ≤ 125°C
80
TJ = 25 °C
82
−40°C ≤ TJ ≤ 125°C
78
V
98
92
dB
TJ = 25 °C
88
−40°C ≤ TJ ≤ 125°C
84
TJ = 25 °C
110
25
−40°C ≤ TJ ≤ 125°C
20
−40°C ≤ TJ ≤ 125°C
30
−40°C ≤ TJ ≤ 125°C
15
−40°C ≤ TJ ≤ 125°C
mV from
either rail
65
67
TJ = 25 °C
35
−40°C ≤ TJ ≤ 125°C
28
LMV792
per channel
75
78
TJ = 25 °C
47
mA
7
−40°C ≤ TJ ≤ 125°C
65
71
TJ = 25 °C
TJ = 25 °C
75
82
TJ = 25 °C
LMV791
Slew rate
pA
10
RLOAD = 2 kΩ to V+/2
SR
1
25
VCM = 1 V (5)
VOUT = 0.15 V to 2.2 V,
RLOAD = 10 kΩ to V+/2
IS
UNIT
μV/°C
−40°C ≤ TJ ≤ 85 °C
LMV791
IOUT
±1.35
mV
VOUT = 0.15 V to 2.2 V,
RLOAD = 2 kΩ to V+/2
AVOL
0.1
±1.65
1.8 V ≤ V+ ≤ 5.5 V, VCM = 0 V
CMVR
MAX (1)
−40°C ≤ TJ ≤ 125°C
TJ = 25 °C
IOS
TYP (2)
15
5
TJ = 25 °C
0.95
−40°C ≤ TJ ≤ 125°C
1.3
1.65
mA
TJ = 25 °C
1.1
−40°C ≤ TJ ≤ 125°C
1.50
1.85
TJ = 25 °C
0.02
1
μA
−40°C ≤ TJ ≤ 125°C
5
AV = +1, Rising (10% to 90%)
8.5
AV = +1, Falling (90% to 10%)
10.5
V/μs
GBW
Gain bandwidth
14
MHz
en
Input referred voltage noise density
f = 1 kHz
6.2
nV/√Hz
in
Input referred current noise density
f = 1 kHz
0.01
pA/√Hz
ton
Turnon time
140
ns
toff
Turnoff time
1000
ns
Enable mode
VEN
(1)
(2)
(3)
(4)
(5)
(6)
2.1
2
Enable pin voltage range
V
Shutdown mode
0.5
0.4
Limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlations using the
statistical quality control (SQC) method.
Typical values represent the parametric norm at the time of characterization.
Offset voltage average drift is determined by dividing the change in VOS by temperature change.
Positive current corresponds to current flowing into the device.
This parameter is specified by design and/or characterization and is not tested in production.
The short circuit test is a momentary test, the short circuit duration is 1.5 ms.
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
5
LMV791, LMV792
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
www.ti.com
2.5-V Electrical Characteristics (continued)
Unless otherwise specified, all limits are ensured for TJ = 25°C, V+ = 2.5 V, V− = 0 V, VCM = V+/2 = VO, VEN = V+.
PARAMETER
IEN
Enable pin input current
THD+N
Total harmonic distortion + noise
MIN (1)
TEST CONDITIONS
Enable mode VEN = 2.5 V
(4)
Shutdown mode VEN = 0 V (4)
f = 1 kHz, AV = 1, RLOAD = 600 Ω
TYP (2)
MAX (1)
1.5
3
0.003
0.1
UNIT
μA
0.01%
6.6 5-V Electrical Characteristics
Unless otherwise specified, all limits are ensured for TJ = 25°C, V+ = 5 V, V− = 0 V, VCM = V+/2 = VO, VEN = V+.
PARAMETER
VOS
Input offset voltage
TC VOS
Input offset voltage temperature drift
IB
Input bias current
MIN (1)
TEST CONDITIONS
TJ = 25 °C
Input offset current
CMRR
PSRR
Common-mode rejection ratio
Power supply rejection ratio
Common-mode voltage range
LMV791 (3)
−1
LMV792 (3)
−1.8
VCM = 2 V (4)
(5)
0.1
−40°C ≤ TJ ≤ 125°C
100
0 V ≤ VCM ≤ 3.7 V
2.0V ≤ V+ ≤ 5.5 V, VCM =
0V
TJ = 25 °C
80
−40°C ≤ TJ ≤ 125°C
75
TJ = 25 °C
80
−40°C ≤ TJ ≤ 125°C
75
dB
80
100
dB
98
TJ = 25 °C
−0.3
4
CMRR ≥ 55 dB
−40°C ≤ TJ ≤ 125°C
−0.3
4
Open-loop voltage gain
LMV792
RLOAD = 10 kΩ to V+/2
VOUT
Output current
+
Sinking to V
VIN = –200 mV (6)
Supply current per amplifier
Shutdown mode (VEN ≤
0.4 V)
82
−40°C ≤ TJ ≤ 125°C
78
V
97
89
dB
TJ = 25 °C
110
35
−40°C ≤ TJ ≤ 125°C
25
−40°C ≤ TJ ≤ 125°C
42
−40°C ≤ TJ ≤ 125°C
45
−40°C ≤ TJ ≤ 125°C
mV from
either rail
80
83
20
−40°C ≤ TJ ≤ 125°C
65
67
TJ = 25 °C
45
−40°C ≤ TJ ≤ 125°C
37
TJ = 25 °C
10
60
mA
−40°C ≤ TJ ≤ 125°C
21
6
TJ = 25 °C
1.15
−40°C ≤ TJ ≤ 125°C
TJ = 25 °C
1.4
1.75
mA
1.3
−40°C ≤ TJ ≤ 125°C
−40°C ≤ TJ ≤ 125°C
75
78
TJ = 25 °C
TJ = 25 °C
65
71
TJ = 25 °C
TJ = 25 °C
LMV792
per channel
75
82
TJ = 25 °C
LMV791
Enable mode
VEN ≥ 4.6 V
TJ = 25 °C
84
LMV792
Sourcing to V−
VIN = 200 mV (6)
80
88
RLOAD = 2 kΩ to V /2
RLOAD = 10 kΩ to V+/2
85
−40°C ≤ TJ ≤ 125°C
−40°C ≤ TJ ≤ 125°C
LMV791
Output voltage swing low
TJ = 25 °C
TJ = 25 °C
+
6
fA
100
CMRR ≥ 60 dB
Output voltage swing high
(2)
(3)
(4)
(5)
(6)
pA
10
RLOAD = 2 kΩ to V+/2
(1)
1
25
VCM = 2 V (5)
VOUT = 0.3V to 4.7V,
RLOAD = 10 kΩ to V+/2
IS
μV/°C
−40°C ≤ TJ ≤ 85°C
LMV791
IOUT
UNIT
mV
VOUT = 0.3V to 4.7V,
RLOAD = 2 kΩ to V+/2
AVOL
±1.35
±1.65
1.8V ≤ V+ ≤ 5.5 V, VCM = 0 V
CMVR
MAX (1)
0.1
−40°C ≤ TJ ≤ 125°C
TJ = 25 °C
IOS
TYP (2)
1.7
2.05
0.14
1
μA
5
Limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlations using the
statistical quality control (SQC) method.
Typical values represent the parametric norm at the time of characterization.
Offset voltage average drift is determined by dividing the change in VOS by temperature change.
Positive current corresponds to current flowing into the device.
This parameter is specified by design and/or characterization and is not tested in production.
The short circuit test is a momentary test, the short circuit duration is 1.5 ms.
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
LMV791, LMV792
www.ti.com
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
5-V Electrical Characteristics (continued)
Unless otherwise specified, all limits are ensured for TJ = 25°C, V+ = 5 V, V− = 0 V, VCM = V+/2 = VO, VEN = V+.
MIN (1)
TYP (2)
AV = +1, Rising (10% to 90%)
6
9.5
AV = +1, Falling (90% to 10%)
7.5
11.5
PARAMETER
SR
Slew rate
TEST CONDITIONS
MAX (1)
UNIT
V/μs
GBW
Gain bandwidth
17
MHz
en
Input referred voltage noise density
f = 1 kHz
5.8
nV/√Hz
in
Input referred current noise density
f = 1 kHz
0.01
pA/√Hz
ton
Turnon time
110
ns
toff
Turnoff time
800
ns
Enable mode
VEN
4.6
4.5
Enable pin voltage range
V
Shutdown mode
IEN
Enable pin input current
THD+N
Total harmonic distortion + noise
Enable mode VEN = 5 V
0.5
(4)
Shutdown mode VEN = 0 V (4)
f = 1 kHz, AV = 1, RLOAD = 600 Ω
0.4
5.6
10
0.005
0.2
0.01%
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
μA
7
LMV791, LMV792
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
www.ti.com
6.7 Typical Characteristics
Unless otherwise specified, TA = 25°C, V– = 0, V+ = Supply Voltage = 5V, VCM = V+/2, VEN = V+.
2
2
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
125°C
1.6
125°C
25°C
1.2
0.8
-40°C
0.4
0
1.5
2.5
3.5
4.5
1.6
25°C
1.2
-40°C
0.8
0.4
0
1.5
5.5 6.0
2.5
3.5
+
4.5
5.5
6
+
V (V)
V (V)
Figure 1. Supply Current vs Supply Voltage (LMV791)
Figure 2. Supply Current vs Supply Voltage (LMV792)
1.8
0.5
1.6
0.45
+
V = 1.8V
0.4
-40°C
1.2
VOS (mV)
SUPPLY CURRENT (PA)
125°C
1.4
1
0.8
0.6
25°C
0.35
0.3
0.4
0.2
0.2
0.15
-40°C
0
1.5
2.5
3.5
4.5
5.5
25°C
0.25
125°C
0.1
-0.3
6.0
0
0.3
+
0.55
0.5
+
125°C
-40°C
0.35
0.4
0.3
VOS (mV)
VOS (mV)
0.4
0.35
25°C
0.3
0.25
25°C
0.25
0.2
0.15
-40°C
0.2
125°C
0.1
0.15
0.05
0.4
1.1
1.8
0
-0.3
VCM (V)
0.6
1.5
2.4
3.3
4.2
VCM (V)
Figure 5. VOS vs VCM
8
+
V = 5V
0.45
0.45
0.1
-0.3
1.2
Figure 4. VOS vs VCM
V = 2.5V
0.5
0.9
VCM (V)
V (V)
Figure 3. Supply Current vs
Supply Voltage in Shutdown Mode
0.6
0.6
Figure 6. VOS vs VCM
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
LMV791, LMV792
www.ti.com
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
Typical Characteristics (continued)
Unless otherwise specified, TA = 25°C, V– = 0, V+ = Supply Voltage = 5V, VCM = V+/2, VEN = V+.
0.5
13
0.45
12
0.4
VOS (mV)
SLEW RATE (V/Ps)
-40°C
0.35
0.3
0.25
25°C
0.2
0.15
11
FALLING
10
9
8
RISING
125°C
0.1
7
0.05
0
1.5
2.5
3.5
4.5
6
1.8
5.5 6.0
2.3
2.8
3.3
4.3
V (V)
2.4
+
+
125°C
V = 5V
125°C
1.1
SUPPLY CURRENT (mA)
1.3
SUPPLY CURRENT (mA)
5.3 5.5
Figure 8. Slew Rate vs Supply Voltage
V = 2.5V
25°C
0.9
-40°C
0.7
0.5
0.3
1.9
25°C
1.4
-40°C
0.9
-40°C
0.4
125°C
0.1
-0.1
-0.1
0
0.5
1
1.5
2
2.5
0
1
Figure 9. Supply Current vs Enable Pin Voltage (LMV791)
1.7
3
4
5
Figure 10. Supply Current vs Enable Pin Voltage(LMV791)
2.4
+
125°C
V = 2.5V
1.5
2
ENABLE PIN VOLTAGE (V)
ENABLE PIN VOLTAGE (V)
+
V = 5V
125°C
25°C
1.3
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
4.8
Figure 7. VOS vs Supply Voltage
V (V)
1.5
3.8
+
+
1.1
0.9
-40°C
0.7
0.5
0.3
1.9
1.4
25°C
0.9
-40°C
-40°C
25°C
0.4
125°C
0.1
-0.1
-0.1
0
0.5
1
1.5
2
2.5
0
1
2
3
4
5
ENABLE PIN VOLTAGE (V)
ENABLE PIN VOLTAGE (V)
Figure 11. Supply Current vs Enable Pin Voltage (LMV792)
Figure 12. Supply Current vs Enable Pin Voltage (LMV792)
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
9
LMV791, LMV792
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified, TA = 25°C, V– = 0, V+ = Supply Voltage = 5V, VCM = V+/2, VEN = V+.
1.5
50
+
V = 5V
-40°C
30
0.5
20
IBIAS (pA)
0
IBIAS (pA)
+
V = 5V
40
1
-0.5
25°C
-1
-1.5
125°C
10
0
85°C
-10
-20
-2
-30
-2.5
-40
-3
-50
0
1
2
3
4
0
1
2
VCM (V)
Figure 13. Input Bias Current vs VCM
35
70
30
125°C
125°C
25
-40°C
50
ISINK (mA)
ISOURCE (mA)
60
25°C
40
30
25°C
20
15
-40°C
10
20
5
10
0
0
1
2
3
4
5
6
1
2
3
4
5
6
+
V+ (V)
V (V)
Figure 15. Sourcing Current vs Supply Voltage
Figure 16. Sinking Current vs Supply Voltage
70
30
125°C
60
125°C
25
50
20
ISINK (mA)
ISOURCE (mA)
4
Figure 14. Input Bias Current vs VCM
80
-40°C
40
25°C
30
25°C
15
10
-40°C
20
5
10
0
0
0
10
3
VCM (V)
1
2
3
4
5
0
1
2
3
4
5
VOUT (V)
VOUT (V)
Figure 17. Sourcing Current vs Output Voltage
Figure 18. Sinking Current vs Output Voltage
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
LMV791, LMV792
www.ti.com
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
Typical Characteristics (continued)
Unless otherwise specified, TA = 25°C, V– = 0, V+ = Supply Voltage = 5V, VCM = V+/2, VEN = V+.
40
25
RLOAD = 10 k:
-40°C
25°C
VOUT FROM RAIL (mV)
VOUT FROM RAIL (mV)
35
30
125°C
25
25°C
20
-40°C
15
10
20
15
125°C
10
5
5
RLOAD = 10 k:
0
1.8
2.5
3.2
3.9
4.6
5.3
0
1.8
6
2.5
3.2
3.9
4.6
5.3
6
+
+
Figure 19. Positive Output Swing vs Supply Voltage
Figure 20. Negative Output Swing vs Supply Voltage
50
50
45
45
125°C
40
25°C
35
30
25
20
-40°C
15
40
35
125°C
30
25
20
15
10
10
5
-40°C
25°C
VOUT FROM RAIL (mV)
VOUT FROM RAIL (mV)
V (V)
V (V)
5
RLOAD = 2 k:
0
1.8
2.5
3.2
RLOAD = 2 k:
0
1.8
2.5
3.2
3.9
4.6
5.3
6
3.9
4.6
5.3
6
+
+
V (V)
V (V)
Figure 21. Positive Output Swing vs Supply Voltage
Figure 22. Negative Output Swing vs Supply Voltage
100
25°C
100
80
125°C
70
60
125°C
RLOAD = 600:
VOUT FROM RAIL (mV)
VOUT FROM RAIL (mV)
90
120
RLOAD = 600:
25°C
50
40
-40°C
30
20
80
-40°C
60
40
20
10
0
1.8
2.5
3.2
3.9
4.6
5.3
6
0
1.8
2.5
3.2
3.9
4.6
5.3
6
+
+
V (V)
V (V)
Figure 23. Positive Output Swing vs Supply Voltage
Figure 24. Negative Output Swing vs Supply Voltage
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
11
LMV791, LMV792
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified, TA = 25°C, V– = 0, V+ = Supply Voltage = 5V, VCM = V+/2, VEN = V+.
100
VS = ±2.5V
+
VCM = 0.0V
V+ = 2.5V
400 nV/DIV
VOLTAGE NOISE (nV/ Hz)
V = 5.5V
10
1
1
10
1k
100
10k
100k
1S/DIV
FREQUENCY (Hz)
Figure 25. Input Referred Voltage Noise vs Frequency
Figure 26. Time Domain Voltage Noise
0
60
+
V = 1.2V
US%
-
-20 V = -0.6V
AV = +2
50
-40
OS%
THD+N (dB)
OVERSHOOT AND UNDERSHOOT %
70
40
30
20
-60
RLOAD = 600:
-80
-100
10
RLOAD = 100 k:
0
20
0
40
80
60
100
-120
0.02
120
0.2
2
CLOAD (pF)
OUTPUT AMPLITUDE (V)
Figure 27. Overshoot and Undershoot vs CLOAD
Figure 28. THD+N vs Peak-to-Peak Output Voltage (VOUT)
0
0.006
+
0.005
RL = 600:
0.004
-60
THD+N (%)
THD+N (dB)
V = 2.75V
-20 V = -2.75V
AV = +2
-40
RLOAD = 600:
-80
-100
RL = 100 k:
0.003
0.002 V+ = 1.2V
-
V = 0.6V
-120
RLOAD = 100 k:
-140
0.02
0.2
2
4
0.001 VO = 0.9 VPP
AV = +2
0
10
100
OUTPUT AMPLITUDE (V)
12
1k
10k
100k
FREQUENCY (Hz)
Figure 29. THD+N vs Peak-to-Peak Output Voltage (VOUT)
Figure 30. THD+N vs Frequency
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
LMV791, LMV792
www.ti.com
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
Typical Characteristics (continued)
Unless otherwise specified, TA = 25°C, V– = 0, V+ = Supply Voltage = 5V, VCM = V+/2, VEN = V+.
120
120
PHASE
100
100
RL = 600:
0.005
CL = 20 pF
80
60
GAIN (dB)
THD+N (%)
0.004
+
0.003
V = 2.5V
-
V = 2.5V
0.002
CL = 50 pF
VO = 4 VPP
GAIN
40
CL = 20 pF
CL = 50 pF
-40
RL = 100 k:
0
10
100
1k
CL = 100 pF
-60
10k
1k
100k
10k
1M
10M
-20
-40
-60
100M
Figure 32. Open-Loop Gain and Phase With Capacitive Load
100
120
120
PHASE
80
80
60
60
40
40
GAIN
20
20
0
0
OUTPUT IMPEDANCE (:)
100
PHASE (°)
GAIN (dB)
100k
0
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 31. THD+N vs Frequency
100
40
20
20
-20
0.001
60
CL = 100 pF
0
AV = +2
80
PHASE (°)
0.006
-20
-20
10
1
0.1
-40
-40
RLOAD = 600: 10 k: 10 M:
-60
10k
100k
1M
0.01
10
-60
100M
10M
100
1k
10k 100k
1M
10M 100M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 33. Open-Loop Gain and Phase With Resistive Load
Figure 34. Closed-Loop Output Impedance vs Frequency
140
120
100
10 mV/DIV
CROSSTALK REJECTION RATION (dB)
160
80
60
40
INPUT = 20 mVPP
f = 1 MHz
20
+
V = 2.5V
0
1k
10k
100k
1M
10M
FREQUENCY (Hz)
100M
200 ns/DIV
AV = +1
Figure 35. Crosstalk Rejection
Figure 36. Small Signal Transient Response
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
13
LMV791, LMV792
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
www.ti.com
Typical Characteristics (continued)
10 mV/DIV
200 mV/DIV
Unless otherwise specified, TA = 25°C, V– = 0, V+ = Supply Voltage = 5V, VCM = V+/2, VEN = V+.
INPUT = 20 mVPP
f = 1 MHz
INPUT = 1 VPP
f = 200 kHz
+
+
V = 5V
V = 2.5V
800 ns/DIV
200 ns/DIV
AV = +1
AV = +1
Figure 37. Large Signal Transient Response
Figure 38. Small Signal Transient Response
50
RLOAD = 600:
200 mV/DIV
PHASE MARGIN (°)
40
INPUT = 1 VPP
f = 200 kHz
+
V = 5V
RLOAD = 10 k:
30
20
RLOAD = 10 M:
10
0
+
V = 2.5V
-10
10
100
1000
800 ns/DIV
CLOAD (pF)
AV = +1
Figure 39. Large Signal Transient Response
Figure 40. Phase Margin vs Capacitive Load (Stability)
0
50
RLOAD = 600:
-20
RLOAD = 10 k:
30
20
RLOAD = 10 M:
10
POSITIVE PSRR (dB)
PHASE MARGIN (°)
40
-40
-60
-80
0
1.8V
+
V = 5V
-10
10
14
5.5V
-100
100
1000
10
100
1k
10k
100k
1M
10M
CLOAD (pF)
FREQUENCY (Hz)
Figure 41. Phase Margin vs Capacitive Load (Stability)
Figure 42. Positive PSRR vs Frequency
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
LMV791, LMV792
www.ti.com
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
Typical Characteristics (continued)
Unless otherwise specified, TA = 25°C, V– = 0, V+ = Supply Voltage = 5V, VCM = V+/2, VEN = V+.
-20
120
100
+
V = 2.5V
80
-60
CMRR (dB)
NEGATIVE PSRR (dB)
-40
+
V = 1.8V
-80
+
V = 5V
60
40
-100
20
+
V = 5.5V
-120
10
100
1k
10k
100k
1M
0
10M
10
1k
100
FREQUENCY (Hz)
10k
100k
1M
FREQUENCY (Hz)
Figure 43. Negative PSRR vs Frequency
Figure 44. CMRR vs Frequency
25
+
V = 5V
CCM (pF)
20
15
10
5
0
0
1
2
3
4
VCM (V)
Figure 45. Input Common-Mode Capacitance vs VCM
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
15
LMV791, LMV792
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
www.ti.com
7 Detailed Description
7.1 Overview
The LMV79x family provides optimal performance in low-voltage and low-noise systems. A low-noise CMOS
input stage, with typical input bias currents in the range of a few femtoamperes, and an input common-mode
voltage range which includes ground make the LMV791 and the LMV792 ideal for low-power sensor applications
7.2 Functional Block Diagram
7.3 Feature Description
7.3.1 Wide Bandwidth at Low Supply Current
The LMV791 and LMV792 are high performance operational amplifiers that provide a unity gain bandwidth of 17
MHz while drawing a low supply current of 1.15 mA. This makes them ideal for providing wideband amplification
in portable applications. The shutdown feature can also be used to design more power efficient systems that
offer wide bandwidth and high performance while consuming less average power.
7.3.2 Low Input Referred Noise and Low Input Bias Current
The LMV79x have a very low input referred voltage noise density (5.8 nV/√Hz at 1 kHz). A CMOS input stage
ensures a small input bias current (100 fA) and low input referred current noise (0.01 pA/√Hz). This is very
helpful in maintaining signal fidelity, and makes the LMV791 and LMV792 ideal for audio and sensor-based
applications.
7.3.3 Low Supply Voltage
The LMV791 and the LMV792 have performance ensured at 2.5-V and 5-V supply. The LMV791 family is
ensured to be operational at all supply voltages between 2 V and 5.5 V, for ambient temperatures ranging from
−40°C to 125°C, thus using the entire battery lifetime. The LMV791 and LMV792 are also ensured to be
operational at 1.8-V supply voltage, for temperatures between 0°C and 125°C. This makes the LMV791 family
ideal for usage in low-voltage commercial applications.
7.3.4 Rail-to-Rail Output and Ground Sensing
Rail-to-rail output swing provides maximum possible dynamic range at the output. This is particularly important
when operating at low supply voltages. An innovative positive feedback scheme is used to boost the current drive
capability of the output stage. This allows the LMV791 and the LMV792 to source more than 40 mA of current at
1.8-V supply. This also limits the performance of the LMV791 family as comparators, and hence the usage of the
LMV791 and the LMV792 in an open-loop configuration is not recommended. The input common-mode range
includes the negative supply rail which allows direct sensing at ground in single supply operation.
7.3.5 Shutdown Feature
The LMV791 family is ideal for battery-powered systems. With a low supply current of 1.15 mA and a shutdown
current of 140 nA typically, the LMV791 and LMV792 allow the designer to maximize battery life. The enable pin
of the LMV791 and the LMV792 allows the operational amplifier to be turned off and reduce its supply current to
less than 1 μA. To power on the operational amplifier the enable pin should be higher than V+ – 0.5 V, where V+
is the positive supply. To disable the operational amplifier, the enable pin voltage should be less than V− + 0.5 V,
where V− is the negative supply.
16
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
LMV791, LMV792
www.ti.com
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
Feature Description (continued)
7.3.6 Small Size
The small footprint of the LMV791 and the LMV792 package saves space on printed-circuit-boards, and enables
the design of smaller electronic products, such as mobile phones, tablets, or other portable systems. Long traces
between the signal source and the operational amplifier make the signal path susceptible to noise. By using a
physically smaller LMV791 and LMV792 package, the operational amplifier can be placed closer to the signal
source, reducing noise pick-up and increasing signal integrity.
7.4 Device Functional Modes
7.4.1 Capacitive Load Tolerance
The LMV791 and LMV792 can directly drive up to 120 pF in unity gain without oscillation. The unity gain follower
is the most sensitive configuration to capacitive loading. Direct capacitive loading reduces the phase margin of
amplifiers. The combination of the output impedance of the amplifier and the capacitive load induces phase lag.
This results in either an underdamped pulse response or oscillation. To drive a heavier capacitive load, the circuit
in Figure 46 can be used.
In Figure 46, the isolation resistor RISO and the load capacitor CL form a pole to increase stability by adding more
phase margin to the overall system. The desired performance depends on the value of RISO. The bigger the RISO
resistor value, the more stable VOUT will be. Increased RISO would, however, result in a reduced output swing and
short circuit current.
Figure 46. Isolation of CL to Improve Stability
7.4.2 Input Capacitance and Feedback Circuit Elements
The LMV791 family has a very low input bias current (100 fA) and a low 1/f noise corner frequency (400 Hz),
which makes it ideal for sensor applications. However, to obtain this performance a large CMOS input stage is
used, which adds to the input capacitance of the operational amplifier, CIN. Though this does not affect the DC
and low frequency performance, at higher frequencies the input capacitance interacts with the input and the
feedback impedances to create a pole, which results in lower phase margin and gain peaking. This can be
controlled by being selective in the use of feedback resistors, as well as by using a feedback capacitance, CF.
For example, in the inverting amplifier shown in Figure 47, if CIN and CF are ignored and the open-loop gain of
the operational amplifier is considered infinite then the gain of the circuit is −R2/R1. An operational amplifier,
however, usually has a dominant pole, which causes its gain to drop with frequency. Hence, this gain is only
valid for DC and low frequency. To understand the effect of the input capacitance coupled with the non-ideal gain
of the operational amplifier, the circuit needs to be analyzed in the frequency domain using a Laplace transform.
CF
R2
R1
+
VIN
CIN
+
+
-
-
AV = -
VOUT
VIN
=-
VOUT
R2
R1
Figure 47. Inverting Amplifier
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
17
LMV791, LMV792
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
www.ti.com
Device Functional Modes (continued)
For simplicity, the operational amplifier is modeled as an ideal integrator with a unity gain frequency of A0.
Hence, its transfer function (or gain) in the frequency domain is A0/s. Solving the circuit equations in the
frequency domain, ignoring CF for the moment, results in an expression for the gain shown in Equation 1.
-R2/R1
(s) =
1+
s2
s
+
§ A0 R 1
§ A0
¨
¨C R
© R1 + R2
© IN 2
§
¨
©
VIN
§
¨
©
VOUT
(1)
It can be inferred from the denominator of the transfer function that it has two poles, whose expressions can be
obtained by solving for the roots of the denominator and are shown in Equation 2.
-1
2CIN
1
1
+
r
R1
R2
§1
1
+
¨
R2
© R1
§
¨
©
P1,2 =
2
-
4 A0CIN
R2
(2)
Equation 2 shows that as the values of R1 and R2 are increased, the magnitude of the poles, and hence the
bandwidth of the amplifier, is reduced. This theory is verified by using different values of R1 and R2 in the circuit
shown in Figure 46 and by comparing their frequency responses. In Figure 48 the frequency responses for three
different values of R1 and R2 are shown. When both R1 and R2 are 1 kΩ, the response is flattest and widest;
whereas, it narrows and peaks significantly when both their values are changed to 10 kΩ or 30 kΩ. So it is
advisable to use lower values of R1 and R2 to obtain a wider and flatter response. Lower resistances also help in
high-sensitivity circuits because they add less noise.
A way of reducing the gain peaking is by adding a feedback capacitance CF in parallel with R2. This introduces
another pole in the system and prevents the formation of pairs of complex conjugate poles which cause the gain
to peak. Figure 49 shows the effect of CF on the frequency response of the circuit. Adding a capacitance of 2 pF
removes the peak, while a capacitance of 5 pF creates a much lower pole and reduces the bandwidth
excessively.
15
20
R1, R2 = 30 k:
AV = -1
10
10
CF = 0 pF
AV = -1
0
0
GAIN (dB)
GAIN (dB)
5
-5
R1, R2 = 30 k:
-10
CF = 5 pF
-10
CF = 2 pF
-20
R1, R2 = 10 k:
-15
R1, R2 = 1 k:
-30
-20
-25
10k
100k
1M
10M
100M
-40
10k
FREQUENCY (Hz)
1M
10M
FREQUENCY (Hz)
Figure 48. Gain Peaking Caused by Large R1, R2
18
100k
Figure 49. Gain Peaking Eliminated by CF
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
LMV791, LMV792
www.ti.com
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LMV791 and LMV792 family of amplifiers is specified for operation from 1.8 V to 5.5 V. Parameters that can
exhibit significant variance with regard to operating voltage or temperature are presented in the Typical
Characteristics section.
8.2 Typical Applications
These application examples highlight a few of the circuits where the LMV791 and LMV792 may be used.
8.2.1 Transimpedance Amplifier
CMOS input operational amplifiers are often used in transimpedance applications as they have an extremely high
input impedance. A transimpedance amplifier converts a small input current into a voltage. This current is usually
generated by a photodiode. The transimpedance gain, measured as the ratio of the output voltage to the input
current, is expected to be large and wide-band. Because the circuit deals with currents in the range of a few nA,
low-noise performance is essential. The LMV79x are CMOS input operational amplifiers providing wide
bandwidth and low noise performance, and are hence ideal for transimpedance applications.
CF
RF
IIN
CCM
CD
VB
+
+
VOUT
CIN = CD + CCM
VOUT
= - RF
IIN
Figure 50. Photodiode Transimpedance Amplifier
8.2.1.1 Design Requirements
Usually, a transimpedance amplifier is designed on the basis of the current source driving the input. A
photodiode is a very common capacitive current source, which requires transimpedance gain for transforming its
miniscule current into easily-detectable voltages. The photodiode and gain of the amplifier are selected with
respect to the speed and accuracy required of the circuit. A faster circuit would require a photodiode with lesser
capacitance and a faster amplifier. A more sensitive circuit would require a sensitive photodiode and a high gain.
A typical transimpedance amplifier is shown in Figure 50. The output voltage of the amplifier is given by the
equation VOUT = −IINRF. Because the output swing of the amplifier is limited, RF should be selected such that all
possible values of IIN can be detected.
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
19
LMV791, LMV792
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
www.ti.com
Typical Applications (continued)
8.2.1.2 Detailed Design Procedure
The LMV79x have a large gain-bandwidth product (17 MHz), which enables high gains at wide bandwidths. A
rail-to-rail output swing at 5.5-V supply allows detection and amplification of a wide range of input currents. A
CMOS input stage with negligible input current noise and low input voltage noise allows the LMV79x to provide
high-fidelity amplification for wide bandwidths. These properties make the LMV79x ideal for systems requiring
wide-band transimpedance amplification.
As mentioned earlier, the following parameters are used to design a transimpedance amplifier: the amplifier gainbandwidth product, A0; the amplifier input capacitance, CCM; the photodiode capacitance, CD; the
transimpedance gain required, RF; and the amplifier output swing. Once a feasible RF is selected using the
amplifier output swing, these numbers can be used to design an amplifier with the desired transimpedance gain
and a maximally flat frequency response.
An essential component for obtaining a maximally flat response is the feedback capacitor, CF. The capacitance
seen at the input of the amplifier, CIN, combined with the feedback capacitor, RF, generate a phase lag which
causes gain-peaking and can destabilize the circuit. CIN is usually just the sum of CD and CCM. The feedback
capacitor CF creates a pole, fP in the noise gain of the circuit, which neutralizes the zero in the noise gain, fZ,
created by the combination of RF and CIN. If properly positioned, the noise gain pole created by CF can ensure
that the slope of the gain remains at 20 dB/decade till the unity gain frequency of the amplifier is reached, thus
ensuring stability. As shown in Figure 51, fP is positioned such that it coincides with the point where the noise
gain intersects the open-loop gain of the operational amplifier. In this case, fP is also the overall 3-dB frequency
of the transimpedance amplifier. The value of CF needed to make it so is given by Equation 3. A larger value of
CF causes excessive reduction of bandwidth, while a smaller value fails to prevent gain peaking and instability.
CF =
1 + 1 + 4SRFCINA0
2SRFA0
(3)
GAIN
OP AMP
OPEN LOOP
GAIN
fZ =
fP =
NOISE GAIN WITH NO CF
1
2S RFCIN
NOISE GAIN WITH CF
A0
2S RF(CIN+CF)
fZ
fP
A0
FREQUENCY
Figure 51. CF Selection for Stability
Calculating CF from Equation 3 can sometimes return unreasonably small values (<1 pF), especially for highspeed applications. In these cases, its often more practical to use the circuit shown in Figure 52 in order to allow
more reasonable values. In this circuit, the capacitance CF′ is (1+ RB/RA) time the effective feedback capacitance,
CF. A larger capacitor can now be used in this circuit to obtain a smaller effective capacitance.
For example, if a CF of 0.5 pF is needed, while only a 5-pF capacitor is available, RB and RA can be selected
such that RB/RA = 9. This would convert a CF′ of 5 pF into a CF of 0.5 pF. This relationship holds as long as RA <
RF.
20
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
LMV791, LMV792
www.ti.com
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
Typical Applications (continued)
RB
RA
CFc
RF
+
IF RA < < RF
RB
§
CF
CFc = ¨1 +
RA
©
§
¨
©
Figure 52. Obtaining Small CF from large CF′
8.2.2 Application Curves
The LMV791 was used to design a number of amplifiers with varying transimpedance gains and source
capacitances. The gains, bandwidths and feedback capacitances of the circuits created are summarized in
Table 1. The frequency responses are presented in Figure 53 and Figure 54. The feedback capacitances are
slightly different from the formula in Equation 3, because the parasitic capacitance of the board and the feedback
resistor RF had to be accounted for.
Table 1. Frequency Response Results
Transimpedance, ATI
CIN
CF
3-dB Frequency
470000
50 pF
1.5 pF
350 kHz
470000
100 pF
2.0 pF
250 kHz
470000
200 pF
3.0 pF
150 kHz
47000
50 pF
4.5 pF
1.5 MHz
47000
100 pF
6.0 pF
1 MHz
47000
200 pF
9.0 pF
700 kHz
130
100
120
CIN = 50 pF, CF = 4.5 pF
95
CIN = 50 pF, CF = 1.5 pF
90
110
GAIN (dB)
GAIN (dB)
85
100
90
CIN = 100 pF, CF = 2 pF
80
70
CIN = 100 pF, CF = 6 pF
75
70
CIN = 200 pF, CF = 9 pF
65
CIN = 200 pF, CF = 3 pF
60
60
50
10k
80
55
100k
1M
10M
50
10k
100k
1M
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 53. Frequency Response for ATI = 470000
Figure 54. Frequency Response for ATI = 47000
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
21
LMV791, LMV792
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
www.ti.com
8.2.3 High-Gain, Wideband Transimpedance Amplifier Using the LMV792
The LMV792, dual, low-noise, wide-bandwidth, CMOS input operational amplifier IC can be used for compact,
robust and integrated solutions for sensing and amplifying wide-band signals obtained from sensitive
photodiodes. One of the two operational amplifiers available can be used to obtain transimpedance gain while
the other can be used for amplifying the output voltage to further enhance the transimpedance gain. The wide
bandwidth of the operational amplifiers (17 MHz) ensures that they are capable of providing high gain for a wide
range of frequencies. The low input referred noise (5.8 nV/√Hz) allows the amplifier to deliver an output with a
high SNR (signal to noise ratio). The small VSSOP-10 footprint saves space on printed-circuit-boards and allows
ease of design in portable products.
The circuit shown in Figure 55, has the first operational amplifier acting as a transimpedance amplifier with a gain
of 47000, while the second stage provides a voltage gain of 10. This provides a total transimpedance gain of
470000 with a −3-dB bandwidth of about 1.5 MHz, for a total input capacitance of 50 pF. The frequency
response for the circuit is shown in Figure 56
4.5 pF
47 k:
10 k:
IIN
-
-
792A
+
CIN = 50 pF
1 k:
792B
+
0.1 PF
+
VOUT
-
ATI =
VOUT
IIN
= 470,000
Figure 55. 1.5-MHz Transimpedance Amplifier, With ATI = 470000
120
110
GAIN (dB)
100
90
80
70
CIN = 50 pF
CF = 4.5 pF
60
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 56. 1.5-MHz Transimpedance Amplifier Frequency Response
8.2.4 Audio Preamplifier With Bandpass Filtering
With low input referred voltage noise, low supply voltage and low supply current, and a low harmonic distortion,
the LMV791 family is ideal for audio applications. Its wide unity gain bandwidth allows it to provide large gain for
a wide range of frequencies and it can be used to design a preamplifier to drive a load of as low as 600 Ω with
less than 0.01% distortion. Two amplifier circuits are shown in Figure 57 and Figure 58. Figure 57 is an inverting
amplifier, with a 10-kΩ feedback resistor, R2, and a 1-kΩ input resistor, R1, and hence provides a gain of −10.
Figure 58 is a noninverting amplifier, using the same values of R1and R2, and provides a gain of 11. In either of
these circuits, the coupling capacitor CC1 decides the lower frequency at which the circuit starts providing gain,
while the feedback capacitor CF decides the frequency at which the gain starts dropping off. Figure 59 shows the
frequency response of the inverting amplifier with different values of CF.
22
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
LMV791, LMV792
www.ti.com
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
+
CF
CC1
R1
1 k:
R2
10 k:
+
VIN
-
RB1
V
V
CC2
+
CC2
+
VIN
-
RB2
-
+
+
RB1
VOUT
RB2
R1
1 k:
AV = -
R2
= -10
R1
CC1
Figure 57. Inverting Audio Preamplifier
+
-
+
R2
10 k:
-
VOUT
CF
AV = 1 +
R2
R1
= 11
Figure 58. Noninverting Audio Preamplifier
25
CF = 10 pF
20
15
CF = 1 nF
GAIN (dB)
10
CF = 100 pF
5
0
-5
-10
-15
-20
1
100
10
1k
100k
10k
1M
FREQUENCY (Hz)
Figure 59. Frequency Response of the Inverting Audio Preamplifier
8.2.5 Sensor Interfaces
The low input bias current and low input referred noise of the LMV791 and LMV792 make them ideal for sensor
interfaces. These circuits are required to sense voltages of the order of a few μV, and currents amounting to less
than a nA, and hence the operational amplifier needs to have low voltage noise and low input bias current.
Typical applications include infrared (IR) thermometry, thermocouple amplifiers and pH electrode buffers.
Figure 60 is an example of a typical circuit used for measuring IR radiation intensity, often used for estimating the
temperature of an object from a distance. The IR sensor generates a voltage proportional to I, which is the
intensity of the IR radiation falling on it. As shown in Figure 60, K is the constant of proportionality relating the
voltage across the IR sensor (VIN) to the radiation intensity, I. The resistances RA and RB are selected to provide
a high gain to amplify this voltage, while CF is added to filter out the high-frequency noise.
+
IR SENSOR
+
VIN = KI
-
IR RADIATION
INTENSITY, I
RB
+
VOUT
RA
CF
VOUT RA
I=
K(RA + RB)
Figure 60. IR Radiation Sensor
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
23
LMV791, LMV792
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
www.ti.com
9 Power Supply Recommendations
For proper operation, the power supplies must be properly decoupled. For decoupling the supply lines, TI
recommends that 10-nF capacitors be placed as close as possible to the operational amplifier power supply pins.
For single-supply, place a capacitor between V+ and V– supply leads. For dual supplies, place one capacitor
between V+ and ground, and one capacitor between V– and ground.
10 Layout
10.1 Layout Guidelines
Connect low-ESR, 0.1-μF ceramic bypass capacitors between each supply pin and ground, placed as close to
the device as possible. A single bypass capacitor from V+ to ground is applicable for single-supply applications.
Noise can propagate into analog circuitry through the power pins of the circuit as a whole and operational
amplifier itself. Bypass capacitors are used to reduce the coupled noise by providing low-impedance power
sources local to the analog circuitry.
Separate grounding for analog and digital portions of circuitry is one of the simplest and most-effective methods
of noise suppression. One or more layers on multilayer PCBs are usually devoted to ground planes. A ground
plane helps distribute heat and reduces EMI noise pickup. Make sure to physically separate digital and analog
grounds, paying attention to the flow of the ground current.
The ground pin should be connected to the PCB ground plane at the pin of the device.
The feedback components should be placed as close to the device as possible minimizing strays.
10.2 Layout Example
Figure 61. Typical SOT Layout
24
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
LMV791, LMV792
www.ti.com
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
11 Device and Documentation Support
11.1 Device Support
11.1.1 Development Support
For developmental support, see the following:
• LMV791 PSPICE Model, SNOM056
• LMV792 PSPICE Model, SNOM057
• TINA-TI SPICE-Based Analog Simulation Program, http://www.ti.com/tool/tina-ti
• DIP Adapter Evaluation Module, http://www.ti.com/tool/dip-adapter-evm
• TI Universal Operational Amplifier Evaluation Module, http://www.ti.com/tool/opampevm
• TI Filterpro Software, http://www.ti.com/tool/filterpro
11.2 Documentation Support
11.2.1 Related Documentation
For related documentation, see the following:
• AN-31 Op Amp Circuit Collection, SNLA140
• Feedback Plots Define Op Amp AC Performance, SBOA015 (AB-028)
• Circuit Board Layout Techniques, SLOA089
• Op Amps for Everyone, SLOD006
• Capacitive Load Drive Solution using an Isolation Resistor, TIPD128
• Handbook of Operational Amplifier Applications, SBOA092
11.3 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 2. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
LMV791
Click here
Click here
Click here
Click here
Click here
LMV792
Click here
Click here
Click here
Click here
Click here
11.4 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.5 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.6 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
25
LMV791, LMV792
SNOSAG6G – SEPTEMBER 2005 – REVISED OCTOBER 2015
www.ti.com
11.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
26
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LMV791 LMV792
PACKAGE OPTION ADDENDUM
www.ti.com
10-Aug-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LMV791MK/NOPB
ACTIVE
SOT
DDC
6
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AS1A
LMV791MKX/NOPB
ACTIVE
SOT
DDC
6
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AS1A
LMV792MM/NOPB
ACTIVE
VSSOP
DGS
10
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AX2A
LMV792MMX/NOPB
ACTIVE
VSSOP
DGS
10
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
AX2A
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
10-Aug-2015
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Aug-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
LMV791MK/NOPB
Package Package Pins
Type Drawing
SOT
DDC
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
6
1000
178.0
B0
(mm)
K0
(mm)
P1
(mm)
8.4
3.2
3.2
1.4
4.0
W
Pin1
(mm) Quadrant
8.0
Q3
LMV791MKX/NOPB
SOT
DDC
6
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LMV792MM/NOPB
VSSOP
DGS
10
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LMV792MMX/NOPB
VSSOP
DGS
10
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Aug-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LMV791MK/NOPB
SOT
DDC
6
1000
210.0
185.0
35.0
LMV791MKX/NOPB
SOT
DDC
6
3000
210.0
185.0
35.0
LMV792MM/NOPB
VSSOP
DGS
10
1000
210.0
185.0
35.0
LMV792MMX/NOPB
VSSOP
DGS
10
3500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
Similar pages