Mean Well HBG-60-1400 Constant current mode output Datasheet

H B G - 6 0 series
60W Constant Current Mode LED Driver
F
■ Features
Constant Current mode output
Circular plastic housing with class II design
Built-in active PFC function
Class 2 power unit
Typical lifetime>50000 hours
5 years warranty
110
SELV
■ Applications
LED bay lighting
LED stage lighting
LED spot lighting
LED down lighting
■ Description
HBG-60 series is a 60W AC/DC LED driver featuring the circular shape design with the plastic
enclosure. It operates from 90~295VAC and offers the constant current output models with
different rated current between 1050mA and 2100mA. Thanks to the high efficiency up to 90%,
with the fanless design, the entire series is able to operate for -40 ℃ ~ +85 ℃ case temperature
under free air convection.
■ Model Encoding
HBG - 60 - 1050
Rated output current(1050mA/1400mA/2100mA)
Rated wattage
Series name
File Name:HBG-60-SPEC 2016-06-16
H B G - 6 0 series
60W Constant Current Mode LED Driver
SPECIFICATION
MODEL
RATED CURRENT
RATED POWER
CONSTANT CURRENT REGION Note.2
OUTPUT
OPEN CIRCUIT VOLTAGE(max.)
CURRENT ADJ. RANGE
CURRENT RIPPLE
Note.4
VOLTAGE RANGE
INPUT
910 ~ 1400mA
1360mA ~ 2100mA
POWER FACTOR
TOTAL HARMONIC DISTORTION
THD< 20%(@load≧65%/115VC,230VAC; @load≧75%/277VAC)
(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
EFFICIENCY (Typ.)
90%
AC CURRENT (Typ.)
0.7A/115VAC
INRUSH CURRENT (Typ.)
MAX. No. of PSUs on 16A
COLD START 45A(twidth=100μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
89%
0.4A/230VAC
89%
0.3A/277VAC
28 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC
<0.75mA / 277VAC
OVER CURRENT
Hiccup mode, recovers automatically after fault condition is removed
OVER TEMPERATURE
Shut down o/p voltage, re-power on to recover
Tcase=-40 ~ +85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
Tcase=+85℃
20 ~ 95% RH non-condensing
-40 ~ +80℃, 10 ~ 95% RH
±0.03%/℃ (0 ~ 60℃)
SAFETY STANDARDS
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
UL8750, CSA C22.2 No. 250.13-12, ENEC EN61347-1 ,EN61347-2-13 independent, E N 62384; GB19510.14, GB19510.1 approved
WITHSTAND VOLTAGE
I/P-O/P:3.75KVAC
ISOLATION RESISTANCE
I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
Compliance to EN55015, GB17743, GB17625.1, EN61000-3-2 Class C (@load≧65%) ; EN61000-3-3
Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, EN55024, light industry level( surge immunity:Line-Line:2KV )
EMC EMISSION Note.8
EMC IMMUNITY
MTBF
NOTE
19 ~ 29V
35V
47 ~ 63Hz
VIBRATION
OTHERS
28 ~ 43V
50V
60V
680 ~ 1050mA
20% max. @rated current
PF>0.97/115VAC, PF>0.95/230VAC, PF>0.9/277VAC@full load
(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
WORKING TEMP.
MAX. CASE TEMP.
WORKING HUMIDITY
ENVIRONMENT
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
EMC
37 ~ 55V
FREQUENCY RANGE
LEAKAGE CURRENT
SAFETY &
HBG-60-2100
2100mA
60.9W
500ms / 230VAC 1200ms / 115VAC
90 ~ 295VAC
127 ~ 417VDC
Note.3
(Please refer to "STATIC CHARACTERISTIC" section)
CIRCUIT BREAKER
PROTECTION
HBG-60-1400
1400mA
60.2W
±5.0%
CURRENT TOLERANCE
SET UP TIME
HBG-60-1050
1050mA
57.75W
DIMENSION
1504.1K hrs min. Telcordia SR-332 (Bellcore) ; 452Khrs min.
ψ110mm * 60.5mm (D * H)
0.5Kg; 20pcs/ 11Kg/ 0.94CUFT
MIL-HDBK-217F (25℃)
PACKING
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
2. Please refer to "DRIVING METHODS OF LED MODULE".
3. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
4. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time.
5. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected
by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
6.To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without permanently
connected to the mains.
7. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 80℃ or less.
8. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com
File Name:HBG-60-SPEC 2016-06-16
H B G - 6 0 series
60W Constant Current Mode LED Driver
BLOCK DIAGRAM
fosc : 50KHz
I/P
EMI FILTER
&
RECTIFIERS
POWER
SWITCHING
O.L.P.
RECTIFIERS
&
FILTER
V+
V-
PWM & PFC
CONTROL
DRIVING METHODS OF LED MODULE
※ This series works in constant current mode to directly drive the LEDs.
In the constant current region, the highest voltage at the output of the driver
depends on the configuration of the end systems.
100
Vo(%)
Constant
Current area
Should there be any compatibility issues, please contact MEAN WELL.
65
(min.)
Hiccup
Protection
50
100
Io(%)
Typical output current normalized by rated current (%)
File Name:HBG-60-SPEC 2016-06-16
H B G - 6 0 series
60W Constant Current Mode LED Driver
OUTPUT LOAD vs TEMPERATURE
100
100
80
80
60
LOAD (%)
LOAD (%)
65
60
40
20
-40
-30
-25
0
15
30
50
60
70
40
20
(HORIZONTAL)
-40
-20
0
10
30
AMBIENT TEMPERATURE,Ta (℃)
50
70
85
90 (HORIZONTAL)
Tcase (℃)
STATIC CHARACTERISTIC
POWER FACTOR (PF) CHARACTERISTIC
※ Tcase at 75℃
1
100
0.95
90
0.9
80
0.85
0.8
60
277V
0.75
PF
LOAD (%)
70
230V
0.7
115V
0.65
50
0.6
40
0.55
0.5
90
100
125
135
145
155 165
175
180
200
230
295
50%
60%
70%
80%
90%
100%
(60W)
INPUT VOLTAGE (V) 60Hz
LOAD
※ De-rating is needed under low input voltage.
TOTAL HARMONIC DISTORTION (THD)
EFFICIENCY vs LOAD
HBG-60 series possess superior working efficiency that up to 90% can
be reached in field applications.
※ 1050mA Model, Tcase at 75℃
※ 1050mA Model, Tcase at 75℃
25%
90
20%
89
277VAC
15%
230VAC
10%
115VAC
5%
EFFICIENCY(%)
THD
91
88
277V
87
230V
115V
86
85
0%
50%
60%
70%
80%
90%
100%
84
50%
LOAD
60%
70%
80%
90%
100%
LOAD
File Name:HBG-60-SPEC 2016-06-16
H B G - 6 0 series
60W Constant Current Mode LED Driver
LIFE TIME
120
LIFETIME(Kh)
100
80
60
40
20
0
25
30
35
40
45
50
55
60
65
70
75
80
85
Tcase ( ℃ )
File Name:HBG-60-SPEC 2016-06-16
H B G - 6 0 series
60W Constant Current Mode LED Driver
MECHANICAL SPECIFICATION
Case No.HBG-60
Unit:mm
57.5
47.5
40
98
4
3
V+(Red)
V-(Black)
ACL(Brown)
ACN(Blue)
98
50
SVT 18AWG*2C
15
29.64
11.2
200
7.56
300
30
SJTW 18AWG*2C
ψ7 . 9
30
tc
27.36
50
ψ108
ψ110
4-ψ5.28
ψ8.36
tc
: Max. Case Temperature
Caution
※ Please inspect the appearance of the driver if the package is damaged. There should not
be any cracks.
※ Please do not drop or bump the driver.
※ All screws including the suspension screw should be paired with a spring washer and locked tight.
※ The entire luminaire, including the driver, should be limited to 5Kg or less.
※ The luminaire should be cautiously protected from damage due to shock throughout packaging and transportation.
※ Please thoroughly follow the preceding cautionary notes to prevent the luminaire from falling, leading to injuries.
File Name:HBG-60-SPEC 2016-06-16
Similar pages