Infineon ICE3AR1080VJZ Of f -line smps cur rent mode cont rol ler wi th integrated 800v Datasheet

CoolS ET ™ F3R80
ICE3AR1080VJZ
O f f - L i n e S MP S C u r r e n t Mo d e C o n t r o l l e r wi t h
i n t e g r a t e d 8 0 0 V CoolMOS™ a n d S t a r t u p c e l l
(input OVP & frequency jitter) in DIP -7
Dat a Sheet
V2.0 2014-01-20
Po wer Manag em ent & Mult im ar k et
Edition 2014-01-20
Published by Infineon Technologies AG,
81726 Munich, Germany.
© 2014 Infineon Technologies AG
All Rights Reserved.
LEGAL DISCLAIMER
THE INFORMATION GIVEN IN THIS APPLICATION NOTE IS GIVEN AS A HINT FOR THE
IMPLEMENTATION OF THE INFINEON TECHNOLOGIES COMPONENT ONLY AND SHALL NOT BE
REGARDED AS ANY DESCRIPTION OR WARRANTY OF A CERTAIN FUNCTIONALITY, CONDITION OR
QUALITY OF THE INFINEON TECHNOLOGIES COMPONENT. THE RECIPIENT OF THIS APPLICATION
NOTE MUST VERIFY ANY FUNCTION DESCRIBED HEREIN IN THE REAL APPLICATION. INFINEON
TECHNOLOGIES HEREBY DISCLAIMS ANY AND ALL WARRANTIES AND LIABILITIES OF ANY KIND
(INCLUDING WITHOUT LIMITATION WARRANTIES OF NON-INFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS OF ANY THIRD PARTY) WITH RESPECT TO ANY AND ALL INFORMATION GIVEN IN
THIS APPLICATION NOTE.
Information
For further information on technology, delivery terms and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in
question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the
failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life
support devices or systems are intended to be implanted in the human body or to support and/or maintain and
sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other
persons may be endangered.
CoolSET™ F3R80
ICE3AR1080VJZ
Trademarks of Infineon Technologies AG
AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, EconoPACK™, CoolMOS™, CoolSET™,
CORECONTROL™, CROSSAVE™, DAVE™, DI-POL™, EasyPIM™, EconoBRIDGE™, EconoDUAL™,
EconoPIM™, EconoPACK™, EiceDRIVER™, eupec™, FCOS™, HITFET™, HybridPACK™, I²RF™,
ISOFACE™, IsoPACK™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OptiMOS™, ORIGA™,
POWERCODE™; PRIMARION™, PrimePACK™, PrimeSTACK™, PRO-SIL™, PROFET™, RASIC™,
ReverSave™, SatRIC™, SIEGET™, SINDRION™, SIPMOS™, SmartLEWIS™, SOLID FLASH™,
TEMPFET™, thinQ!™, TRENCHSTOP™, TriCore™.
Other Trademarks
Advance Design System™ (ADS) of Agilent Technologies, AMBA™, ARM™, MULTI-ICE™, KEIL™,
PRIMECELL™, REALVIEW™, THUMB™, µVision™ of ARM Limited, UK. AUTOSAR™ is licensed by
AUTOSAR development partnership. Bluetooth™ of Bluetooth SIG Inc. CAT-iq™ of DECT Forum.
COLOSSUS™, FirstGPS™ of Trimble Navigation Ltd. EMV™ of EMVCo, LLC (Visa Holdings Inc.). EPCOS™
of Epcos AG. FLEXGO™ of Microsoft Corporation. FlexRay™ is licensed by FlexRay Consortium.
HYPERTERMINAL™ of Hilgraeve Incorporated. IEC™ of Commission Electrotechnique Internationale. IrDA™
of Infrared Data Association Corporation. ISO™ of INTERNATIONAL ORGANIZATION FOR
STANDARDIZATION. MATLAB™ of MathWorks, Inc. MAXIM™ of Maxim Integrated Products, Inc.
MICROTEC™, NUCLEUS™ of Mentor Graphics Corporation. MIPI™ of MIPI Alliance, Inc. MIPS™ of MIPS
Technologies, Inc., USA. muRata™ of MURATA MANUFACTURING CO., MICROWAVE OFFICE™ (MWO) of
Applied Wave Research Inc., OmniVision™ of OmniVision Technologies, Inc. Openwave™ Openwave Systems
Inc. RED HAT™ Red Hat, Inc. RFMD™ RF Micro Devices, Inc. SIRIUS™ of Sirius Satellite Radio Inc.
SOLARIS™ of Sun Microsystems, Inc. SPANSION™ of Spansion LLC Ltd. Symbian™ of Symbian Software
Limited. TAIYO YUDEN™ of Taiyo Yuden Co. TEAKLITE™ of CEVA, Inc. TEKTRONIX™ of Tektronix Inc.
TOKO™ of TOKO KABUSHIKI KAISHA TA. UNIX™ of X/Open Company Limited. VERILOG™, PALLADIUM™
of Cadence Design Systems, Inc. VLYNQ™ of Texas Instruments Incorporated. VXWORKS™, WIND RIVER™
of WIND RIVER SYSTEMS, INC. ZETEX™ of Diodes Zetex Limited.
Last Trademarks Update 2011-11-11
Data Sheet
3
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Revision History
Major changes since previous revision
Date
Version
20 Jan 2014
2.0
Changed By
Change Description
Release of first version
We Listen to Your Comments
Is there any information in this document that you feel is wrong, unclear or missing?
Your feedback will help us to continuously improve the quality of our documentation.
Please send your proposal (including a reference to this document title/number) to:
[email protected]
Data Sheet
4
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Table of Contents
Revision History .............................................................................................................................................. 4
Table of Contents ............................................................................................................................................ 5
Off-Line SMPS Current Mode Controller with integrated 800V CoolMOS™ and Startup cell (input OVP &
frequency jitter) in DIP-7................................................................................................................. 7
1
1.1
1.2
Pin Configuration and Functionality ........................................................................................... 8
Pin Configuration with PG-DIP-7 .................................................................................................... 8
Pin Functionality............................................................................................................................. 8
2
Representative Block Diagram .................................................................................................. 10
3
3.1
3.2
3.3
3.3.1
3.3.2
3.4
3.5
3.5.1
3.5.2
3.5.3
3.6
3.6.1
3.6.2
3.7
3.7.1
3.7.2
3.7.2.1
3.7.2.2
3.7.2.3
3.7.2.4
3.7.3
3.7.3.1
3.7.3.2
3.7.4
3.7.5
Functional Description............................................................................................................... 11
Introduction .................................................................................................................................. 11
Power Management ..................................................................................................................... 11
Improved Current Mode ............................................................................................................... 12
PWM-OP................................................................................................................................. 14
PWM-Comparator ................................................................................................................... 14
Startup Phase .............................................................................................................................. 14
PWM Section ............................................................................................................................... 17
Oscillator................................................................................................................................. 17
PWM-Latch FF1 ...................................................................................................................... 17
Gate Driver ............................................................................................................................. 17
Current Limiting............................................................................................................................ 18
Leading Edge Blanking ........................................................................................................... 19
Propagation Delay Compensation (patented)........................................................................... 19
Control Unit .................................................................................................................................. 20
Basic and Extendable Blanking Mode...................................................................................... 20
Active Burst Mode (patented) .................................................................................................. 21
Selectable burst entry level................................................................................................. 22
Entering Active Burst Mode ................................................................................................ 23
Working in Active Burst Mode ............................................................................................. 23
Leaving Active Burst Mode ................................................................................................. 23
Protection Modes .................................................................................................................... 24
Vcc OVP, OTP and Vcc under voltage................................................................................ 25
Over load, open loop protection .......................................................................................... 26
Input OVP Mode...................................................................................................................... 27
Action sequence at BV pin ...................................................................................................... 28
4
4.1
4.2
4.3
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
4.3.6
Electrical Characteristics........................................................................................................... 30
Absolute Maximum Ratings .......................................................................................................... 30
Operating Range.......................................................................................................................... 31
Characteristics ............................................................................................................................. 31
Supply Section ........................................................................................................................ 31
Internal Voltage Reference ...................................................................................................... 32
PWM Section .......................................................................................................................... 32
Soft Start time ......................................................................................................................... 32
Control Unit ............................................................................................................................. 33
Current Limiting....................................................................................................................... 34
Data Sheet
5
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
4.3.7
CoolMOS™ Section ................................................................................................................ 34
5
Typical Controller Performance Characteristics ...................................................................... 35
6
CoolMOS™ Performance Characteristics ................................................................................. 36
7
Input Power Curve ..................................................................................................................... 38
8
Outline Dimension ..................................................................................................................... 39
9
Marking ....................................................................................................................................... 40
10
Schematic for recommended PCB layout ................................................................................. 41
Data Sheet
6
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Off-Line SMPS Current Mode Controller with integrated 800V CoolMOS™
and Startup cell (input OVP & frequency jitter) in DIP-7
Product Highlights
 800V avalanche rugged CoolMOS™ with startup cell
 Active Burst Mode to reach the lowest Standby Power <100mW
 Selectable entry and exit burst mode level
 Adjustable blanking Window for high load jumps
PG-DIP7
 Frequency jitter and soft driving for low EMI
 Adjustable input OVP
 Auto Restart protection for over load, over temperature and over voltage
 Low Operating temperature down to -40°C
 Pb-free lead plating, halogen free mold compound, RoHS compliant
Features
 800V avalanche rugged CoolMOS™ with Startup Cell
 Active Burst Mode for lowest Standby Power
 Selectable entry and exit burst mode level
 100kHz internally fixed switching frequency with jittering feature
 Auto Restart Protection for Over load, Open Loop, VCC Under voltage & Over voltage and Over temperature
 Over temperature protection with 50°C hysteresis
 Built-in 10ms Soft Start
 Built-in 20ms and extendable blanking time for short duration peak power
 Propagation delay compensation for both maximum load and burst mode
 Adjustable input OVP
 Overall tolerance of Current Limiting < ±5%
 BiCMOS technology for low power consumption and wide VCC voltage range
 Soft gate drive with 50Ω turn on resistor
Description
The ICE3AR1080VJZ is a modified version of ICE3ARxx80JZ (CoolSET™-F3R 800V) in DIP-7 package. It adds in
the input OVP feature but removes the brownout feature and external protection enable feature. In summary, the
ICE3AR1080VJZ is a device running at 100kHz, implemented with input OVP feature, installed with 800V MOSFET
with startup cell and housed in DIP-7 package. It provides good voltage margin of MOSFET, lowest standby power,
selectable burst level, reduced output ripple during burst mode, robust protection with input OVP feature, accurate
maximum power control for both maximum power and burst power, low EMI with frequency jittering and soft gate
drive, built-in and flexible protections, etc.
Applications
 Adapter/Charger
 Blue Ray/DVD player, Set-top Box, Digital Photo Frame
 Auxiliary power supply for Server, PC, Printer, TV, Home theater/Audio System, White Goods, etc
Typical Application
+
85 ... 270 VAC
Converter
DC Output
Snubber
CBulk
-
CVCC
VCC
Drain
Startup Cell
Power Management
PWM Controller
Current Mode
CoolMOS®
CS
Precise Low Tolerance Peak
Current Limitation
ROV1
BV
RSense
FBB
Control Unit
Active Burst Mode
Input OVP mode
Auto Restart Mode
CoolSET®- F3R80
(Input OVP & Jitter)
GND
ROV2
Figure 1:
Typical Application
Type
Package
Marking
VDS
FOSC
RDSon
ICE3AR1080VJZ
PG-DIP-7
3AR1080VJZ
800V
100kHz
1.0
1)
2)
2)
230VAC ±15%
85-265 VAC
71W
45W
1) typ @ T=25°C
2) Calculated maximum input power rating at Ta=50°C, Ti=125°C and without copper area as heat sink.
Data Sheet
7
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Pin Configuration and Functionality
1
Pin Configuration and Functionality
1.1
Pin Configuration with PG-DIP-7
Pin
Symbol
Function
1
BV
extended Blanking time & input OVP
2
FBB
Feedback & Burst entry/exit control
3
CS
Current Sense/ 800V CoolMOS™ Source
4
n.c.
not connected
5
Drain
800V CoolMOS™ Drain
6
-
(no pin)
7
VCC
Controller Supply Voltage
8
GND
Controller Ground
Figure 2:
1.2
BV
1
8
GND
FBB
2
7
VCC
CS
3
n.c.
4
5
Drain
Pin configuration PG-DIP-7(top view)
Pin Functionality
BV (extended Blanking time & input OVP)
The BV pin combines the functions of input OVP and extendable blanking time for over load protection. The input
OVP feature is to stop the switching pulse when the input line voltage is higher than the VOVP_ref after the resistor
divider (Refer to Figure 3). The extendable blanking time function is to extend the built-in 20 ms blanking time for
over load protection by adding an external capacitor to ground.
FBB (Feedback & Burst entry control)
The FBB pin combines the feedback function and the burst entry/exit control. The regulation information is
provided by the FBB pin to the internal Protection Unit and the internal PWM-Comparator to control the duty cycle.
The FBB-signal is the only control signal in case of light load at the Active Burst Mode. The burst entry/ exit control
provides an access to select the entry/exit burst mode level.
CS (Current Sense)
The Current Sense pin senses the voltage developed on the shunt resistor inserted in the source of the integrated
CoolMOS™. If CS reaches the internal threshold of the Current Limit Comparator, the Driver output is immediately
switched off. Furthermore the current information is provided for the PWM comparator to realize the Current Mode.
Data Sheet
8
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Pin Configuration and Functionality
Drain (Drain of integrated CoolMOS™)
Pin Drain is the connection to the Drain of the integrated CoolMOS™.
VCC (Power Supply)
The VCC pin is the positive supply of the IC. The operating range is between 10.5V and 25V.
GND (Ground)
The GND pin is the ground of the controller.
Data Sheet
9
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Representative Block Diagram
2
Figure 3:
Data Sheet
Representative Block Diagram
Representative Block Diagram
10
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
3
Functional Description
All values which are used in the functional description are typical values. For calculating the worst cases the
min/max values which can be found in section 4 Electrical Characteristics have to be considered.
3.1
Introduction
ICE3AR1080VJZ input OVP and jitter 800V version is the modified version of the ICE3ARxx80JZ. It is particular
good for high voltage margin low power SMPS application such as white goods, auxiliary power supply for PC and
server. The major characteristics are that the IC is developed with 800V CoolMOS™ with start up cell, having
adjustable input OVP feature, running at 100kHz switching frequency and packed in DIP-7 package.
The familiar features are BiCMOS technology to reduce power consumption and increase the Vcc voltage range,
cycle by cycle current mode control, built-in 10ms soft start to reduce the stress of switching elements during start up,
built-in 20ms and extended blanking time for short period of peak power before entering protection, active burst mode
for lowest standby power and propagation delay compensation for close power limit between high line and low line,
frequency jittering for low EMI performance, the built-in auto-restart mode protections for open loop, over load, Vcc
OVP, Vcc under voltage, etc.
Besides, it also includes narrowing the feedback voltage swing from 0.5V to 0.3V during burst mode so that the
output voltage ripple can be reduced by 40%, reduction of the fast voltage fall time of the MOSFET by increasing
the soft turn-on time and addition of 50Ω turn-on resistor, faster start up time by optimizing the Vcc capacitor to
10uF and over temperature protection with 50°C hysteresis.
Furthermore, it includes adjustable input OVP to suppress the abnormal input stress to damage the device,
selectable entry and exit burst mode for smaller entry/exit power to burst mode or even no burst mode is possible and
the propagation delay compensation for burst mode so that the entry/exit burst mode power is close between high
line and low line.
In summary, the ICE3AR1080VJZ provides good voltage margin of MOSFET, lowest standby power, flexible
burst level, reduced output ripple during burst mode, robust for abnormal input stress with input OVP feature,
accurate power limit for both maximum power and burst power, low EMI with frequency jittering and soft gate
drive, built-in and flexible protections, etc. Therefore, ICE3AR1080VJZ is a complete solution for the low power
SMPS application typically for white goods.
3.2
Power Management
Drain
VCC
Startup Cell
CoolMOS®
Power Management
Undervoltage Lockout
17V
Internal Bias
10.5V
Voltage
Reference
Power-Down Reset
5.0V
Auto Restart
Mode
Soft Start block
Figure 4:
Active Burst Mode
Power Management
The Undervoltage Lockout monitors the external supply voltage VVCC. When the SMPS is plugged to the main line the
internal Startup Cell is biased and starts to charge the external capacitor CVCC which is connected to the VCC pin. This
Data Sheet
11
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
VCC charge current is controlled to 0.9mA by the Startup Cell. When the VVCC exceeds the on-threshold VCCon=17V the
bias circuit are switched on. Then the Startup Cell is switched off by the Undervoltage Lockout and therefore no power
losses present due to the connection of the Startup Cell to the Drain voltage. To avoid uncontrolled ringing at switchon, a hysteresis start up voltage is implemented. The switch-off of the controller can only take place when VVCC falls
below 10.5V after normal operation was entered. The maximum current consumption before the controller is activated
is about 200µA.
When VVCC falls below the off-threshold VCCoff=10.5V, the bias circuit is switched off and the soft start counter is
reset. Thus it ensures that at every startup cycle the soft start starts at zero.
The internal bias circuit is switched off if Auto Restart Mode is entered. The current consumption is then
reduced to 320µA.
Once the malfunction condition is removed, this block will then turn back on. The recovery from Auto Restart Mode
does not require re-cycling the AC line.
When Active Burst Mode is entered, the internal Bias is switched off most of the time but the Voltage Reference is
kept alive in order to reduce the current consumption below 620µA.
3.3
Improved Current Mode
Soft-Start Comparator
PWM-Latch
FBB
C8
R
Q
Driver
S
Q
0.6V
PWM OP
x3.25
CS
Improved
Current Mode
Figure 5:
Current Mode
Current Mode means the duty cycle is controlled by the slope of the primary current. This is done by comparing the
FBB signal with the amplified current sense signal.
Amplified Current Signal
FBB
0.6V
Driver
t
ton
t
Figure 6:
Pulse Width Modulation
In case the amplified current sense signal exceeds the FBB signal the on-time ton of the driver is finished by
resetting the PWM-Latch (Figure 6).
Data Sheet
12
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
The primary current is sensed by the external series resistor RSense inserted in the source of the integrated
CoolMOS™. By means of Current Mode regulation, the secondary output voltage is insensitive to the line variations.
The current waveform slope will change with the line variation, which controls the duty cycle.
The external RSense allows an individual adjustment of the maximum source current of the integrated
CoolMOS™.
To improve the Current Mode during light load conditions the amplified current ramp of the PWM-OP is
superimposed on a voltage ramp, which is built by the switch T2, the voltage source V1 and a resistor R1 (see
Figure 7). Every time the oscillator shuts down for maximum duty cycle limitation the switch T2 is closed by VOSC.
When the oscillator triggers the Gate Driver, T2 is opened so that the voltage ramp can start.
Soft-Start Comparator
PWM Comparator
FBB
C8
PWM-Latch
Oscillator
VOSC
time delay
circuit (156ns)
Gate Driver
0.6V
10k
X3.25
R1
T2
V1
PWM OP
Voltage Ramp
Figure 7:
Improved Current Mode
In case of light load the amplified current ramp is too small to ensure a stable regulation. In that case the
Voltage Ramp is a well defined signal for the comparison with the FBB-signal. The duty cycle is then controlled
by the slope of the Voltage Ramp.
By means of the time delay circuit which is triggered by the inverted VOSC signal, the Gate Driver is switched-off until it
reaches approximately 156ns delay time (Figure 8). It allows the duty cycle to be reduced continuously till 0% by
decreasing VFBB below that threshold.
VOSC
max.
Duty Cycle
Voltage
Ramp
t
0.6V
FBB
Gate
Driver
t
156ns time delay
t
Figure 8:
Data Sheet
Light Load Conditions
13
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
3.3.1
PWM-OP
The input of the PWM-OP is applied over the internal leading edge blanking to the external sense resistor RSense
connected to pin CS. RSense converts the source current into a sense voltage. The sense voltage is amplified with a
gain of 3.25 by PWM OP. The output of the PWM-OP is connected to the voltage source V1. The voltage ramp with
the superimposed amplified current signal is fed into the positive inputs of the PWM-Comparator C8 and the Soft-StartComparator (Figure 9).
3.3.2
PWM-Comparator
The PWM-Comparator compares the sensed current signal of the integrated CoolMOS™ with the feedback
signal VFBB (Figure 9). VFBB is created by an external optocoupler or external transistor in combination with the
internal pull-up resistor RFB and provides the load information of the feedback circuitry. When the amplified
current signal of the integrated CoolMOS™ exceeds the signal VFBB the PWM-Comparator switches off the Gate
Driver.
5V
RFB
Soft-Start Comparator
FBB
PWM-Latch
C8
PWM Comparator
0.6V
Optocoupler
PWM OP
CS
X3.25
Improved
Current Mode
Figure 9:
3.4
PWM Controlling
Startup Phase
Soft Start finish
Soft Start counter
SoftS
Soft Start
Soft Start
Soft-Start
Comparator
C7
&
Gate Driver
G7
0.6V
x3.25
CS
PWM OP
Figure 10:
Data Sheet
Soft Start
14
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
In the Startup Phase, the IC provides a Soft Start period to control the primary current by means of a duty cycle
limitation. The Soft Start function is a built-in function and it is controlled by an internal counter.
Figure 11:
Soft Start Phase
When the VVCC exceeds the on-threshold voltage, the IC starts the Soft Start mode (Figure 10).
The function is realized by an internal Soft Start resistor, a current sink and a counter. And the amplitude of the
current sink is controlled by the counter (Figure 12).
5V
RSoftS
SoftS
Soft Start 32I
Counter
Figure 12:
8I
4I
2I
I
Soft Start Circuit
After the IC is switched on, the VSoftS voltage is controlled such that the voltage is increased step-wisely (32
steps) with the increase of the counts. The Soft Start counter would send a signal to the current sink control in
every 300µs such that the current sink decrease gradually and the duty ratio of the gate drive increases
gradually. The Soft Start will be finished in 10ms (t Soft-Start) after the IC is switched on. At the end of the Soft Start
period, the current sink is switched off.
Within the soft start period, the duty cycle is increasing from zero to maximum gradually (see Figure 13).
Data Sheet
15
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
VSoftS
tSoft-Start
VSOFTS32
t
Gate
Driver
t
Figure 13:
Gate drive signal under Soft-Start Phase
In addition to Start-Up, Soft-Start is also activated at each restart attempt during Auto Restart.
VSoftS
tSoft-Start
VSOFTS32
VFB
t
4.5V
VOUT
t
VOUT
tStart-Up
t
Figure 14:
Start Up Phase
The Start-Up time tStart-Up before the converter output voltage VOUT is settled, must be shorter than the Soft-Start Phase
tSoft-Start (Figure 14). By means of Soft-Start there is an effective minimization of current and voltage stresses on the
integrated CoolMOS™, the clamp circuit and the output rectifier and it helps to prevent saturation of the transformer
during Start-Up.
Data Sheet
16
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
3.5
PWM Section
0.75
PWM Section
Oscillator
Duty Cycle
max
Clock
Frequency
Jitter
Soft Start
Block
FF1
Soft Start
Comparator
R
G8
PWM
Comparator
Gate Driver
S
1
Q
&
G9
Current
Limiting
CoolMOS®
Gate
Figure 15:
3.5.1
PWM Section Block
Oscillator
The oscillator generates a fixed frequency of 100kHz with frequency jittering of ±4% (which is ±4KHz) at a
jittering period of 4ms.
A capacitor, a current source and current sink which determine the frequency are integrated. The charging and
discharging current of the implemented oscillator capacitor are internally trimmed in order to achieve a very accurate
switching frequency. The ratio of controlled charge to discharge current is adjusted to reach a maximum duty cycle
limitation of Dmax=0.75.
Once the Soft Start period is over and when the IC goes into normal operating mode, the switching frequency of the
clock is varied by the control signal from the Soft Start block. Then the switching frequency is varied in range of
100kHz ± 4KHz at period of 4ms.
3.5.2
PWM-Latch FF1
The output of the oscillator block provides continuous pulse to the PWM-Latch which turns on/off the integrated
CoolMOS™. After the PWM-Latch is set, it is reset by the PWM comparator, the Soft Start comparator or the
Current -Limit comparator. When it is in reset mode, the output of the driver is shut down immediately.
3.5.3
Gate Driver
VCC
PWM-Latch
1
50
Gate
CoolMOS®
Gate Driver
Figure 16:
Data Sheet
Gate Driver
17
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
The driver-stage is optimized to minimize EMI and to provide high circuit efficiency. This is done by reducing the
switch on slope when exceeding the integrated CoolMOS™ threshold. This is achieved by a slope control of the
rising edge at the driver’s output (Figure 17) and adding a 50Ω gate turn on resistor (Figure 15). Thus the leading
switch on spike is minimized.
(internal)
VGate
typ. t = 160ns
4.6V
t
Figure 17:
Gate Rising Slope
Furthermore the driver circuit is designed to eliminate cross conduction of the output stage.
During power up, when VCC is below the undervoltage lockout threshold VVCCoff, the output of the Gate Driver is set
to low in order to disable power transfer to the secondary side.
3.6
Current Limiting
PWM Latch
FF1
Current Limiting
Propagation-Delay
Compensation
Vcsth
LEB
220ns
C10
PWM-OP
LEB
180ns
&
C12
G10
S4
VCSth_burst
Propagation-Delay
Compensation-Burst
Active Burst
Mode
or
G13
VFB_burst
10k
C5
1pF
D1
CS
FBB
Figure 18:
Current Limiting Block
There is a cycle by cycle peak current limiting operation realized by the Current-Limit comparator C10. The source
current of the integrated CoolMOS™ is sensed via an external sense resistor RSense. By means of RSense the source
current is transformed to a sense voltage VSense which is fed into the pin CS. If the voltage VSense exceeds the internal
threshold voltage Vcsth, the comparator C10 immediately turns off the gate drive by resetting the PWM Latch FF1.
A Propagation Delay Compensation is added to support the immediate shut down of the integrated CoolMOS™
with very short propagation delay. Thus the influence of the AC input voltage on the maximum output power can
be reduced to minimal. This compensation applies to both the peak load and burst mode.
In order to prevent the current limit from distortions caused by leading edge spikes, a Leading Edge Blanking
(LEB) is integrated in the current sense path for the comparators C10, C12 and the PWM-OP.
The output of comparator C12 is activated by the Gate G10 if Active Burst Mode is entered. When it is activated,
the current limiting is reduced to Vcsth_burst. This voltage level determines the maximum power level in Active
Burst Mode.
Data Sheet
18
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
3.6.1
Leading Edge Blanking
VSense
Vcsth
tLEB = 220ns/180ns
t
Figure 19:
Leading Edge Blanking
Whenever the integrated CoolMOS™ is switched on, a leading edge spike is generated due to the primary-side
capacitances and reverse recovery time of the secondary-side rectifier. This spike can cause the gate drive to
switch off unintentionally. In order to avoid a premature termination of the switching pulse, this spike is blanked out
with a time constant of tLEB = 220ns for normal load and tLEB = 180ns for burst mode.
3.6.2
Propagation Delay Compensation (patented)
In case of overcurrent detection, there is always propagation delay to switch off the integrated CoolMOS™. An
overshoot of the peak current Ipeak is induced to the delay, which depends on the ratio of dI/ dt of the peak
current (Figure 20).
Signal2
Signal1
tPropagation Delay
ISense
IOvershoot2
Ipeak2
Ipeak1
ILimit
IOvershoot1
t
Figure 20:
Current Limiting
The overshoot of Signal2 is larger than of Signal1 due to the steeper rising waveform. This change in the slope
is depending on the AC input voltage. Propagation Delay Compensation is integrated to reduce the overshoot
due to dI/dt of the rising primary current. Thus the propagation delay time between exceeding the current sense
threshold Vcsth and the switching off of the integrated CoolMOS™ is compensated over temperature within a wide
input range. Current Limiting is then very accurate.
For example, Ipeak = 0.5A with RSense = 2. The current sense threshold is set to a static voltage level Vcsth=1V without
Propagation Delay Compensation. A current ramp of dI/dt = 0.4A/µs, or dVSense/dt = 0.8V/µs, and a propagation
delay time of tPropagation Delay =180ns leads to an Ipeak overshoot of 14.4%. With the propagation delay compensation,
the overshoot is only around 2% (Figure 21).
without compensation
with compensation
V
1,3
1,25
VSense
1,2
1,15
1,1
1,05
1
0,95
0,9
0
0,2
0,4
0,6
0,8
1
1,2
dVSense
dt
Figure 21:
Data Sheet
1,4
1,6
1,8
2
V
s
Overcurrent Shutdown
19
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
The Propagation Delay Compensation is realized by means of a dynamic threshold voltage Vcsth (Figure 22). In
case of a steeper slope the switch off of the driver is earlier to compensate the delay.
VOSC
max. Duty Cycle
off time
VSense
Propagation Delay
t
Vcsth
Signal1
Figure 22:
Signal2
t
Dynamic Voltage Threshold Vcsth
Similarly, the same concept of propagation delay compensation is also implemented in burst mode with reduced
level, Vcsth_burst (Figure 18). With this implementation, the entry and exit burst mode power can be very close
between low line and high line input voltage.
3.7
Control Unit
The Control Unit contains the functions for Active Burst Mode and Auto Restart Mode. The Active Burst Mode and
the Auto Restart Mode both have 20ms internal blanking time. For the over load Auto Restart Mode, the 20ms
blanking time can be further extended by adding an external capacitor at BV pin. With the blanking time, the IC
avoids entering into those two modes accidentally. That buffer time is very useful for the application which works in
short duration of peak power occasionally.
3.7.1
Basic and Extendable Blanking Mode
5.0V
Auto
Restart
Mode
Ichg_EB
S1
Spike
Blanking
30us
4.5V
ROV2
#
C11
BV
Counter
CBK
CT1
500
&
G5
C3
0.9V
S2
FBB
20ms
Blanking
Time
C4
4.5V
Figure 23:
Control Unit
Basic and Extendable Blanking Mode
There are 2 kinds of Blanking mode; basic mode and the extendable mode. The basic mode is a built-in 20ms
blanking time while the extendable mode can extend this blanking time by connecting an external capacitor to the
BV pin. For the extendable mode, the gate G5 remains blocked even though the 20ms blanking time is reached.
After reaching the 20ms blanking time the counter is activated and the switch S1 is turned on to charge the voltage
of BV pin by the constant current source, Ichg_EB. When the voltage of BV pin hits 4.5V, which is sensed by
Data Sheet
20
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
comparator C11, the counter will increase the counter by 1. Then it switches off the switch S1 and turns on the
switch S2. The voltage at BV pin will be discharged through a 500Ω resistor. When the voltage drops to 0.9V which
is sensed by comparator C3, the switch S2 will be turned off and the switch S1 will be turned on. Then the constant
current Ichg_EB will charge the CBK capacitor again. When the voltage at BV hits 4.5V which is sensed by comparator
C11, the counter will increase the count to 2. The process repeats until it reaches total count of 256 (Figure 24).
Then the counter will release a high output signal. When the AND gate G5 detects both high signals at the inputs, it
will activate the 30µs spike blanking circuit and finally the auto-restart mode will be activated.
Figure 24:
Waveform at extended blanking time
For example, if CBK=0.1µF, Ichg_EB=720µA, ROV2=15KΩ,
Ichg_EB’=Ichg_EB-(4.5V+0.9V)/(2*ROV2)=540 µA
Extended blanking time = 256*(CBK*(4.5V-0.9V)/ Ichg_EB’+ CBK*500*ln(4.5/0.9)) = 192ms
Total blanking time = 20ms+192 = 212ms
where Ichg_EB’=net charging current to CBK
Note: The above calculation does not include the effect of the input OVP circuit where there is extra biasing
current flowing from the input. That means the extended blanking time will be shortened with the line voltage
change if input OVP circuit is implemented.
3.7.2
Active Burst Mode (patented)
To increase the efficiency of the system at light load, the most effective way is to operate at burst mode. Starting from
CoolSET™™ F3, the IC has been employing the active burst mode and it can achieve the lowest standby power.
ICE3AR1080VJZ adopts the same concept with some more innovative improvements to the feature. It includes the
adjustable entry burst level, close power control between high line and low line and the smaller output ripple during
burst mode.
Most of the burst mode design in the market will provide a fixed entry burst mode level which is a ratio to the
maximum power of the design. ICE3AR1080VJZ provides a more flexible level which can be selected externally. The
provision also includes not entering burst mode.
Propagation delay is the major contributor for the power control variation for DCM flyback converter. It is proved to
be effective in the maximum power control. ICE3AR1080VJZ also apply the same concept in the burst mode.
Therefore, the entry and exit burst mode power is also finely controlled during burst mode.
The feedback control swing during burst mode will affect the output ripple voltage directly. ICE3AR1080VJZ
reduces the swing from 0.5V to 0.3V. Therefore, it would have around 40% improvement for the output ripple.
Data Sheet
21
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
Current Limiting
CS
Vcsth_burst
C12
G10 & FF1
Internal
Bias
Burst detect
and adjust
VFB_burst
C5
20 ms Blanking
Time
FBB
CFB
Active Burst
Mode
C13
4.0V
3.5V
C6a
&
G11
C6b
3.2V
Figure 25:
Control Unit
Active Burst Mode
The Active Burst Mode is located in the Control Unit. Figure 24 shows the related components.
3.7.2.1
Selectable burst entry level
The burst mode entry level can be selected by changing the different capacitor CFB at FBB pin. There are 4 levels to
be selected with different capacitor which are targeted for 10%, 6.67%, 4.38% and 0% of the maximum input power.
At the same time, the exit burst levels are targeted to 20%, 13.3%, 9.6% and 0% of the maximum power accordingly.
The corresponding capacitance range is from 6.8nF to 100pF. The below table is the recommended capacitance
range for the entry and exit level with the CFB capacitor.
CFB
Entry level
% of Pin_max
VFB_burst
Exit level
% of Pin_max
Vcsth_burst
10%
1.60V
20%
0.45V
1nF~2.2nF (1%,COG)
6.67%
1.42V
13.3%
0.37V
220pF~470pF (1%,COG)
4.38%
1.27V
9.6%
0.31V
>=6.8nF (5%,X7R)
<=100pF (1%,COG)
0%
never
0%
always
The selection is at the 1st 1ms of the UVLO “ON” (Vcc > 17V) during the 1st start up but it does not detect in the
subsequent re-start due to auto-restart protection. In case there is protection triggered such as input OVP before
starts up, the detection will be held until the protection is removed. When the Vcc reaches the UVLO “ON” in the 1st
start up, the capacitor CFB at FBB pin is charged by a 5V voltage source through the RFB resistor. When the voltage
at FBB pin hits 4.5V, the FF4 will be set, the switch S9 is turned “ON” and the counter will increase by 1. Then the
CFB is discharged through a 500Ω resistor. After reaching 0.5V, the FF4 is reset and the switch S9 is turned “OFF”.
Then the CFB capacitor is charged by the 5V voltage source again until it reaches 4.5V. The process repeats until
the end of 1ms. Then the detection is ended. After that, the total number of count in the counter is compared and
the VFB-burst and the Vcs_burst are selected accordingly (Figure 26)
Data Sheet
22
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
VFB_burst
VCSth_burst
5V
Comparator
logic
counter
UVLO
RFB
4.5V
FBB
C19
S
Q
FF4
CFB
500
S9
0.5V
UVLO during
1st startup
C20
R
1ms
timer
Control Unit
Figure 26:
3.7.2.2
Entry Burst Mode detection
Entering Active Burst Mode
The FBB signal is kept monitoring by the comparator C5 (Figure 25). During normal operation, the internal
blanking time counter is reset to 0. When FBB signal falls below VFB_burst, it starts to count. When the counter reaches
20ms and FBB signal is still below VFB_burst, the system enters the Active Burst Mode. This time window prevents a sudden
entering into the Active Burst Mode due to large load jumps.
After entering Active Burst Mode, a burst flag is set and the internal bias is switched off in order to reduce the
current consumption of the IC to about 620µA.
It needs the application to enforce the VCC voltage above the Undervoltage Lockout level of 10.5V such that the
Startup Cell will not be switched on accidentally. Or otherwise the power loss will increase drastically. The
minimum VCC level during Active Burst Mode depends on the load condition and the application. The lowest
VCC level is reached at no load condition.
3.7.2.3
Working in Active Burst Mode
After entering the Active Burst Mode, the FBB voltage rises as VOUT starts to decrease, which is due to the
inactive PWM section. The comparator C6a monitors the FBB signal. If the voltage level is larger than 3.5V, the
internal circuit will be activated; the Internal Bias circuit resumes and starts to provide switching pulse. In Active
Burst Mode the gate G10 is released and the current limit is reduced to Vcsth_burst (Figure 3 and Figure 25). In one
hand, it can reduce the conduction loss and the other hand, it can reduce the audible noise. If the load at V OUT is
still kept unchanged, the FBB signal will drop to 3.2V. At this level the C6b deactivates the internal circuit again
by switching off the Internal Bias. The gate G11 is active again as the burst flag is set after entering Active Burst
Mode. In Active Burst Mode, the FBB voltage is changing like a saw tooth between 3.2V and 3.5V (Figure 27).
3.7.2.4
Leaving Active Burst Mode
The FBB voltage will increase immediately if there is a high load jump. This is observed by the comparator C13
(Figure 25). Since the current limit is reduced to 31%~45% of the maximum current during active burst mode, it
needs a certain load jump to raise the FBB signal to exceed 4.0V. At that time the comparator C5 resets the
Active Burst Mode control which in turn blocks the comparator C12 by the gate G10. The maximum current can
then be resumed to stabilize VOUT.
Data Sheet
23
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
VFBB
Entering
Active Burst
Mode
4.0V
3.5V
3.2V
Leaving Active
Burst Mode
VFB_burst
Blanking Timer
t
20ms Blanking Time
VCS
Vcsth
t
Current limit level during
Active Burst Mode
Vcsth_burst
VVCC
t
10.5V
IVCC
t
5.7mA
620uA
VOUT
t
t
Figure 27:
3.7.3
Signals in Active Burst Mode
Protection Modes
The IC provides Auto Restart mode as the major protection feature. Auto Restart mode can prevent the SMPS from
destructive states. There are 3 kinds of auto restart mode; normal auto restart mode, odd skip auto restart mode
and non switch auto restart mode. Odd skip auto restart mode is that there is no detect of fault and no switching
pulse for the odd number restart cycle. At the even number of restart cycle the fault detect and soft start switching
pulses maintained. If the fault persists, it would continue the auto-restart mode. However, if the fault is removed,
it can release to normal operation only at the even number auto restart cycle (Figure 28).
VVCC
Fault
detected
Startup and detect
No detect
No detect
17V
10.5V
VCS
t
t
Figure 28:
Data Sheet
Odd skip auto restart waveform
24
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
Non switch auto restart mode is similar to odd skip auto restart mode except the start up switching pulses are also
suppressed at the even number of the restart cycle. The detection of fault still remains at the even number of the
restart cycle. When the fault is removed, the IC will resume to normal operation at the even number of the restart
cycle (Figure 29).
Fault
detected
VVCC
Startup and detect
No detect
No detect
17V
10.5V
VCS
t
No switching
t
Figure 29:
Non switch auto restart waveform
The main purpose of the odd skip auto restart is to extend the restart time such that the power loss during auto
restart protection can be reduced. This feature is particularly good for smaller Vcc capacitor where the restart time
is shorter.
The following table lists the possible system failures and the corresponding protection modes.
VCC Over voltage (1)
Odd skip Auto Restart Mode
VCC Over voltage (2)
Odd skip Auto Restart Mode
Over load
Odd skip Auto Restart Mode
Open Loop
Odd skip Auto Restart Mode
VCC Undervoltage
Normal Auto Restart Mode
Short Optocoupler
Normal Auto Restart Mode
Over temperature
Non switch Auto Restart Mode
3.7.3.1
Vcc OVP, OTP and Vcc under voltage
Auto Restart
Mode Reset
VVCC < 10.5V
Thermal Shutdown
Tj >130°C
25.5V
C2
120μs blanking
time
Spike
Blanking
30μs
Auto Restart
mode
VCC
C1
20.5V
4.5V
C4
&
Voltage
Reference
G1
Control Unit
FBB
softs_period
Figure 30:
Vcc OVP and OTP
There are 2 types of Vcc over voltage protection; Vcc OVP (1) and Vcc OVP (2). The Vcc OVP (1) takes action
only during the soft start period. The Vcc OVP (2) takes the action in any conditions.
Vcc OVP (1) condition is when VVCC voltage is > 20.5V, VFBB voltage is > 4.5V and during soft start period, the IC
enters into odd skip Auto Restart Mode. This condition likely happens during start up at open loop fault (Figure 30).
Data Sheet
25
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
Vcc OVP (2) condition is when V VCC voltage is > 25.5V, the IC enters into odd skip Auto Restart Mode (Figure
30).
The over temperature protection OTP is sensed inside the controller IC. The Thermal Shutdown block keeps on
monitoring the junction temperature of the controller. After detecting a junction temperature higher than 130°C, the
IC will enter into the non switch Auto Restart mode. The ICE3AR1080VJZ has also implemented with a 50°C
hysteresis. That means the IC can only be recovered when the controller junction temperature is dropped 50 °C
lower than the over temperature trigger point (Figure 30).
The VCC undervoltage and short opto-coupler will go into the normal auto restart mode inherently.
In case of VCC undervoltage, the Vcc voltage drops indefinitely. When it drops below the Vcc under voltage lock out
“OFF” voltage (10.5V), the IC will turn off the IC and the startup cell will turn on again. Then the Vcc voltage will be
charged up to UVLO “ON” voltage (17V) and the IC turns on again provided the startup cell charge up current is not
drained by the fault. If the fault is not removed, the Vcc will continue to drop until it hits UVLO “OFF” voltage and the
restart cycle repeats.
Short Optocoupler can lead to Vcc undervoltage because once the opto-coupler (transistor side) is shorted, the
feedback voltage will drop to zero and there will be no switching pulse. Then the Vcc voltage will drop same as
the Vcc undervoltage.
3.7.3.2
Over load, open loop protection
Voltage
Reference
5.0V
Auto Restart
Mode Reset
VVCC < 10.5V
Ichg_EB
Auto
Restart
Mode
S1
ROV2 CBK
#
4.5V
BV
C11
counter
500
0.9V
C3
CT1
Spike
Blanking
30us
&
G5
S2
FBB
20ms
Blanking
Time
C4
4.5V
Figure 31:
Control Unit
Over load, open loop protection
In case of Overload or Open Loop, the FBB exceeds 4.5V which will be observed by comparator C4. Then the builtin blanking time counter starts to count. When it reaches 20ms, the extended blanking time counter CT1 is
activated. The switch S2 is turned on and the voltage at the BV pin will be discharged through 500Ω resistor. When
it drops to 0.9V, the switch S2 is turned off and the Switch S1 is turned on. Then a constant current source Ichg_EB
will start to charge up BV pin. When the voltage hits 4.5V which is monitored by comparator C11, the switch S1 is
turned off and the count will increase by 1. Then the switch S2 will turn on again and the voltage will drop to 0.9V
and rise to 4.5V again. The count will then increase by 1 again. When the total count reaches 256, the counter
CT1 will stop and it will release a high output signal. When both the input signals at AND gate G5 is high, the
odd skip Auto Restart Mode is activated after the 30µs spike blanking time (Figure 31).
The total blanking time depends on the addition of the built-in and the extended blanking time. If there is no CBK
capacitor at BV pin, the count will finish within 0.1ms and the equivalent blanking time is just the built-in time of
20ms.
Since the BV pin is a multi-function pin, it would share with different functions. The resistor ROV2 from input OVP
feature application may however affect the extendable blanking time (Figure 31). Thus it should take the ROV2
into the calculation of the extendable blanking time. For example the extended blanking time may be changed
from 181ms to 212ms for 42.2KΩ to 15KΩ ROV2 resistor. The list below shows one particular CBK, ROV2 vs
blanking time.
Data Sheet
26
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
CBK
ROV2
Extended blanking time
Overall blanking time
0.1uF
42.2KΩ
161ms
181ms
0.1uF
39.6KΩ
162ms
182ms
0.1uF
15KΩ
192ms
212ms
Another factor to affect the extended blanking time is the input voltage through the ROV1 and ROV2. It would, on the
contrary, reduce the extended blanking time.
3.7.4
Input OVP Mode
When the AC input voltage is out of the designed operating range (e.g. > 300Vac), the voltage at the input bulk
capacitor will increase at the same time. If the MOSFET keeps on switching, the drain voltage may be too high and
the MOSFET will exceed the maximum voltage rating and causes damages. The input OVP mode is to prevent this
phenomenon. The IC will sense the input voltage through the input bulk capacitor to the BV pin by 2 potential divider
resistors, ROV1 and ROV2 (Figure 32). During normal operation, the BV pin voltage is lower than VOVP_ref (1.98V). The
output of C14a is low and the output of G21 is high. Together with UVLO high signal (IC operating) the “S” input of
FF5 is low. The “Q” output of FF5 is low and the input OVP mode remains not activated. When there is an input over
voltage case, the input bulk capacitor voltage is increased and the BV voltage is increased to larger than VOVP_ref. The
output of C14a is high and the output of G21 is low. If the OVP persists for 400µs (blanking time) and the UVLO
signal is still high, the output of G20 is high. Then the “S” input of FF5 is high and the “Q” output of FF5 is high. The
input OVP mode is set. The case of UVLO signal low is not considered as it means the IC is not working.
UVLO
Q
S
G20
Vbulk
400µs Blanking
time
1.98V
ROV1
R
Q
FF5
G21
C14a
Input OVP
BV
G22
5µs Blanking
time
C14b
ROV2
1.91V
Control Unit
Figure 32:
Input OVP detection circuit
Once the system enters the input OVP mode, there will be no switching pulse and the IC keeps on monitoring the
BV signal. If the input OVP signal is not reset, there is no switching pulse in each restart cycle (Figure 33).
VBV
Input OVP
detected
Input OVP
released
1.98V
1.91V
VVCC
Switching start at the
following restart cycle
t
17V
10.5V
VCS
t
No switching
t
Figure 33:
Data Sheet
Input OVP mode waveform
27
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
The IC implemented with hysteresis voltage to leave the input OVP protection. The hysteresis voltage at BV pin is
VOVP_hys (0.07V) and the input OVP reset voltage at BV pin is VOVP_ref - VOVP_hys; i.e. 1.91V. After the input OVP
protection is triggered, the voltage at BV pin needs to drop VOVP_hys from VOVP_ref before it can be reset.
When the BV voltage drops below 1.91V, the output of C14b and G22 are high (Figure 32). The “R” input of the
FF5 is high. Then the “Q” output of FF5 is low. The input OVP is reset. The system will turn on with soft start in the
coming restart cycle when Vcc reaches the Vcc “ON” voltage at 17V.
The input OVP feature can also be applied to customer defined protection circuit by pulling up the BV pin to
larger than VOVP_ref.
The formula to calculate the ROV1 and ROV2 are as below.
Set ROV1 to a particular value.
ROV2= ROV1* VOVP_ref /(VOVP - VOVP_ref)
The formula to calculate the input OVP reset voltage is as below.
VOVP_reset=(VOVP_ref - VOVP_hys)*( ROV1+ROV2)/ROV2
where VOVP: input over voltage; VOVP_reset: input over reset voltage; VOVP_ref: IC reference voltage for OVP; VOVP_hys: IC
hysteresis voltage for OVP; ROV1 and ROV2: resistors divider from input voltage to BV pin.
For example,
VOVP_ref=1.98V, VOVP_hys=0.07V
If input OVP voltage, VOVP=424Vdc (300Vac), ROV1=9MΩ, ROV2=42.2KΩ
Input OVP reset, VOVP_reset=408Vdc (289Vac)
To disable input OVP feature, the BV pin must be connected with a resistor ROV2≥15KΩ to IC ground and
remove ROV1.
(Remark: ROV2 must be always ≥15KΩ in all conditions, otherwise overload protection may not work)
3.7.5
Action sequence at BV pin
Since there are 2 functions at the same BV pin; input OVP and extended blanking time, the action of sequence is
whichever starts first takes the priority. When the “Extended blanking time” is triggered by OLP and follows with the
“Input OVP” triggering, then the OLP will continue to work until it ends. The IC would recheck the signal at BV pin
after one skip cycle. If the BV signal exceeds the input OVP threshold, it would go to input OVP mode.
Data Sheet
28
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Functional Description
OLP
detected
OLP
released
VFB
4.5V
Extended OLP
blanking time
Built in 20ms OLP
blanking time
VBV
4.5V
Input OVP
Input OVP fault started( but
overridden by extended blanking
OLP time)
Input OVP
detected
t
Input OVP
released
1.98V
1.91V
0.9V
t
Switching start at the
following restart cycle
VVCC
17V
10.5V
t
VCS
No switching
t
Figure 34:
Input OVP during extended blanking time
One typical case happened is that the overload happened first and it follows with the “Input OVP” feature at the 1st
20ms blanking time. Since the overload protection is still not triggered at the 1st 20ms blanking time period and the
extended blanking time is not running, the input OVP mode will trigger right away.
OLP
detected
OLP
released
VFB
4.5V
Built in 20ms OLP
blanking time
t
Input OVP
VBV
Input OVP
detected
Input OVP
released
1.98V
1.91V
VVCC
Switching start at the
following restart cycle
t
17V
10.5V
t
VCS
No switching
t
Figure 35:
Data Sheet
Input OVP during first 20ms blanking time
29
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Electrical Characteristics
4
Note:
Electrical Characteristics
All voltages are measured with respect to ground (Pin 8). The voltage levels are valid if other ratings
are not violated.
4.1
Note:
Absolute Maximum Ratings
Absolute maximum ratings are defined as ratings, which when being exceeded may lead to destruction of
the integrated circuit. For the same reason make sure, that any capacitor that will be connected to pin 7
°
(VCC) is discharged before assembling the application circuit. Ta=25 C unless otherwise specified.
Parameter
Symbol
Limit Values
Unit
min.
max.
VDS
-
800
V
ID_Puls
-
11.5
A
Avalanche energy, repetitive tAR limited
by max. Tj=150°C1)
EAR
-
0.1
mJ
Avalanche current, repetitive tAR limited
by max. Tj=150°C
IAR
-
3.5
A
Drain Source Voltage
Pulse drain current, tp limited by Tjmax
VCC Supply Voltage
VVCC
-0.3
27
V
FBB Voltage
VFBB
-0.3
5.5
V
BV Voltage
VBV
-0.3
5.5
V
CS Voltage
VCS
-0.3
5.5
Junction Temperature
Storage Temperature
-40
Tj
V
150
°
°
TS
-55
150
Thermal Resistance
Junction -Ambient
RthJA
-
96
Soldering temperature,
wavesoldering only allowed at leads
Tsold
-
260
ESD Capability (incl. Drain Pin)
VESD
-
2
Remarks
C
Controller & CoolMOS™
C
K/W
°
1.6mm (0.063in.) from
case for 10s
kV
Human body model2)
C
1) Repetitive avalanche causes additional power losses that can be calculated as PAV=EAR*f
2) According to EIA/JESD22-A114-B (discharging a 100pF capacitor through a 1.5KΩ series resistor)
Data Sheet
30
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Electrical Characteristics
4.2
Operating Range
Note: Within the operating range the IC operates as described in the functional description.
Parameter
Symbol
Limit Values
min.
max.
Unit
Remarks
V
Max value limited due to Vcc OVP
VCC Supply Voltage
VVCC
VVCCoff
25
Junction Temperature of
Controller
TjCon
-40
130
°
Junction Temperature of
CoolMOS™
TjCoolMOS
-40
150
°
4.3
Characteristics
4.3.1
Supply Section
C
Max value limited due to thermal
shut down of controller
C
Note: The electrical characteristics involve the spread of values within the specified supply voltage and
junction temperature range TJ from – 40 °C to 125 °C. Typical values represent the median values,
which are related to 25°C. If not otherwise stated, a supply voltage of VCC = 17 V is assumed.
Parameter
Symbol
Limit Values
Unit
Test Condition
min.
typ.
max.
IVCCstart
-
200
300
μA
VVCC =16V
IVCCcharge1
-
-
5.0
mA
VVCC = 0V
IVCCcharge2
0.55
0.9
1.60
mA
VVCC = 1V
IVCCcharge3
0.38
0.7
-
mA
VVCC =16V
Leakage Current of
Start Up Cell and CoolMOS™
IStartLeak
-
0.2
50
μA
Supply Current with
Inactive Gate
IVCCsup1
-
1.9
3.2
mA
Supply Current with Active Gate
IVCCsup2
-
5.7
7.8
mA
IFBB = 0A
Supply Current in
Auto Restart Mode with Inactive
Gate
IVCCrestart
-
320
-
μA
IFBB = 0A
Supply Current in Active Burst
Mode with Inactive Gate
IVCCburst1
-
620
950
μA
VFBB = 2.5V
IVCCburst2
-
620
950
μA
VVCC = 11.5V, VFBB
= 2.5V
VVCCon
VVCCoff
VVCChys
16.0
9.8
-
17.0
10.5
6.5
18.0
11.2
-
V
V
V
Start Up Current
VCC Charge Current
VCC Turn-On
ThresholdVCC Turn-Off
Threshold VCC Turn-On/Off
Hysteresis
VDrain = 650V
1)
at Tj=100°C
1) The parameter is not subjected to production test - verified by design/characterization
Data Sheet
31
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Electrical Characteristics
4.3.2
Internal Voltage Reference
Parameter
Trimmed Reference Voltage
4.3.3
Symbol
VREF
Limit Values
Unit
min.
typ.
max.
4.90
5.00
5.10
V
Test Condition
measured at pin FBB
IFBB = 0
PWM Section
Parameter
Symbol
Limit Values
Unit
Test Condition
min.
typ.
max.
fOSC1
87
100
113
kHz
fOSC2
90
100
108
kHz
Tj = 25°C
Frequency Jittering Range
fjitter
-
±4.0
-
kHz
Tj = 25°C
Frequency Jittering period
Tjitter
-
4.0
-
ms
Tj = 25°C
Max. Duty Cycle
Dmax
0.70
0.75
0.80
Min. Duty Cycle
Dmin
0
-
-
PWM-OP Gain
AV
3.05
3.25
3.45
Voltage Ramp Offset
VOffset-Ramp
-
0.60
-
V
VFBB Operating Range
Min Level
VFBmin
-
0.7
-
V
VFBB Operating Range Max
level
VFBmax
-
-
4.3
V
RFB
9.0
15.4
23.0
kΩ
Fixed Oscillator Frequency
FBB Pull-Up Resistor
VFBB < 0.3V
CS=1V, limited by
Comparator C41)
1) The parameter is not subjected to production test - verified by design/characterization
4.3.4
Soft Start time
Parameter
Soft Start time
Data Sheet
Symbol
tSS
Limit Values
Unit
min.
typ.
max.
-
10
-
32
Test Condition
ms
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Electrical Characteristics
4.3.5
Control Unit
Parameter
Symbol
Input OVP reference voltage for
comparator C14a
VOVP_ref
Input OVP hysteresis C14b
VOVP_hys
Limit Values
Unit
min.
typ.
max.
1.90
1.98
2.06
0.07
Test Condition
V
Tj = 25°C
V
Tj = 25°C
Blanking time voltage lower limit
for Comparator C3
VBKC3
0.80
0.90
1.00
V
Blanking time voltage upper limit
for Comparator C11
VBKC11
4.28
4.50
4.72
V
Over Load Limit for Comparator C4
VFBC4
4.28
4.50
4.72
V
Entry Burst select High level for
Comparator C19
VFBC19
4.28
4.50
4.72
V
Entry Burst select Low level for
Comparator C20
VFBC20
0.40
0.50
0.60
V
10% Pin_max
VFB_burst1
1.51
1.60
1.69
V
< 7 counts
6.67% Pin_max
VFB_burst2
1.34
1.42
1.50
V
8 ~ 39 counts
4.38% Pin_max
VFB_burst3
1.20
1.27
1.34
V
40 ~ 191 counts
Active Burst Mode High Level for
Comparator C6a
VFBC6a
3.35
3.50
3.65
V
In Active Burst Mode
Active Burst Mode Low Level for
Comparator C6b
VFBC6b
3.06
3.20
3.34
V
Active Burst Mode Level for
Comparator C13
VFBC13
3.85
4.00
4.15
V
Overvoltage Detection Limit for
Comparator C1
VVCCOVP1
19.5
20.5
21.5
V
Overvoltage Detection Limit for
Comparator C2
VVCCOVP2
25.0
25.5
26.3
V
Ichg_EB
460
720
864
μA
TjSD
130
140
150
°
Active Burst Mode
Entry Level for
Comparator C5
Charging current for extended
blanking time
Thermal Shutdown1)
C
TjSD_hys
-
50
-
°
tBK
-
20
-
ms
Timer for entry burst select
tEBS
-
1
-
ms
Spike Blanking Time for Auto-Restart
Protection
tSpike
-
30
-
μs
Hysteresis for thermal Shutdown1)
Built-in Blanking Time for Overload
Protection or enter Active Burst Mode
1)
VFBB = 5V, during soft
start
Controller
C
The parameter is not subjected to production test - verified by design/characterization. The thermal shutdown temperature refers to the
junction temperature of the controller.
Note:
The trend of all the voltage levels in the Control Unit is the same regarding the deviation except
VVCCOVP and VVCCPD
Data Sheet
33
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Electrical Characteristics
4.3.6
Current Limiting
Parameter
Symbol
Peak Current Limitation
(incl. Propagation Delay)
Peak Current
20% Pin_max
Limitation during
Active Burst Mode 13.3% Pin_max
9.6% Pin_max
Leading Edge
Blanking
Vcsth
Unit
min.
typ.
max.
0.98
1.06
1.13
V
Test Condition
dVsense / dt = 0.6V/µs
(Figure 21)
Vcsth_burst1
0.37
0.45
0.51
V
< 7 counts
Vcsth_burst2
0.30
0.37
0.44
V
8 ~ 39 counts
Vcsth_burst3
0.23
0.31
0.37
V
40 ~ 191 counts
Normal mode
tLEB_normal
-
220
-
ns
Burst mode
tLEB_burst
-
180
-
ns
ICSbias
-1.5
-0.2
-
μA
CS Input Bias Current
4.3.7
Limit Values
VCS =0V
CoolMOS™ Section
Parameter
Symbol
Limit Values
Unit
Test Condition
min.
typ.
max.
V(BR)DSS
800
870
Drain Source On-Resistance
RDSon
-
1.00
2.24
1.11
2.46
V
V


Tj = 25°C
Tj = 110°C1)
Tj = 25°C
Tj=125°C1)
at ID = 1.35A
Effective output capacitance, energy
related
Co(er)
-
24
-
pF
VDS = 0V to 480V
Rise Time
trise
-
302)
-
ns
Drain Source Breakdown Voltage
2)
30
ns
tfall
1) The parameter is not subjected to production test - verified by design/characterization
Fall Time
2) Measured in a Typical Flyback Converter Application
Data Sheet
34
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Typical Controller Performance Characteristics
5
Typical Controller Performance Characteristics
Characterisrtic graphs are normalized at Ta=25°C
Figure 36:
Line OVP (VOVP_ref) vs. T a
Figure 37:
Hystersis of Line OVP (VOVP_hys) vs. T a
Data Sheet
35
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
CoolMOS™ Performance Characteristics
6
CoolMOS™ Performance Characteristics
Figure 38:
Safe Operating Area (SOA) curve for ICE3AR1080VJZ
Figure 39:
SOA temperature derating coefficient curve
Data Sheet
36
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
CoolMOS™ Performance Characteristics
Figure 40:
Power dissipation; P tot=f(T a)
Figure 41:
Drain-source breakdown voltage; VBR(DSS)=f(Tj), ID=0.25mA
Data Sheet
37
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Input Power Curve
7
Input Power Curve
Two input power curves giving the typical input power versus ambient temperature are showed below;
Vin=85Vac~265Vac (Figure 42) and Vin=230Vac+/-15% (Figure 43). The curves are derived based on a typical
discontinuous mode flyback model which considers either 50% maximum duty ratio or 100V maximum
secondary to primary reflected voltage (higher priority). The calculation is based on no copper area as heatsink
for the device. The input power already includes the power loss at input common mode choke, bridge rectifier
and the CoolMOS™. The device saturation current (ID_Puls @ Tj=125°C) is also considered.
To estimate the output power of the device, it is simply multiplying the input power at a particular operating ambient
temperature with the estimated efficiency for the application. For example, a wide range input voltage (Figure 42),
operating temperature is 50°C, estimated efficiency is 85%, then the estimated output power is 38W (45W * 85%).
Figure 42:
Input power curve Vin=85~265Vac; Pin=f(T a)
Figure 43:
Input power curve Vin=230Vac; Pin=f(Ta)
Data Sheet
38
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Outline Dimension
8
Figure 44:
Data Sheet
Outline Dimension
PG-DIP-7 (Pb-free lead plating Plastic Dual-in-Line Outline)
39
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Marking
9
Figure 45:
Data Sheet
Marking
Marking for ICE3AR1080VJZ
40
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Schematic for recommended PCB layout
10
Figure 46:
Schematic for recommended PCB layout
Schematic for recommended PCB layout
General guideline for PCB layout design using F3 CoolSET™ (refer to Figure 46):
1. “Star Ground “at bulk capacitor ground, C11:
“Star Ground “means all primary DC grounds should be connected to the ground of bulk capacitor C11
separately in one point. It can reduce the switching noise going into the sensitive pins of the CoolSET™
device effectively. The primary DC grounds include the followings.
a. DC ground of the primary auxiliary winding in power transformer, TR1, and ground of C16 and Z11.
b. DC ground of the current sense resistor, R12
c. DC ground of the CoolSET™ device, GND pin of IC11; the signal grounds from C13, C14, C15 and collector
of IC12 should be connected to the GND pin of IC11 and then “star “connect to the bulk capacitor ground.
d. DC ground from bridge rectifier, BR1
e. DC ground from the bridging Y-capacitor, C4
2. High voltage traces clearance:
High voltage traces should keep enough spacing to the nearby traces. Otherwise, arcing would incur.
a. 400V traces (positive rail of bulk capacitor C11) to nearby trace: > 2.0mm
b. 600V traces (drain voltage of CoolSET™ IC11) to nearby trace: > 2.5mm
3. Filter capacitor close to the controller ground:
Filter capacitors, C13, C14 and C15 should be placed as close to the controller ground and the controller
pin as possible so as to reduce the switching noise coupled into the controller.
Data Sheet
41
V2.0, 2014-01-20
CoolSET™ F3R80
ICE3AR1080VJZ
Schematic for recommended PCB layout
Guideline for PCB layout design when >3KV lightning surge test applied (refer to Figure 46):
1. Add spark gap
Spark gap is a pair of saw-tooth like copper plate facing each other which can discharge the accumulated
charge during surge test through the sharp point of the saw-tooth plate.
a. Spark Gap 3 and Spark Gap 4, input common mode choke,
L1: Gap separation is around 1.5mm (no safety concern)
b. Spark Gap 1 and Spark Gap 2, Live / Neutral to GROUND:
These 2 Spark Gaps can be used when the lightning surge requirement is>6KV.
230Vac input voltage application, the gap separation is around 5.5mm
115Vac input voltage application, the gap separation is around 3mm
2. Add Y-capacitor (C2 and C3) in the Live and Neutral to ground even though it is a 2-pin input
3. Add negative pulse clamping diode, D11 to the Current sense resistor, R12:
The negative pulse clamping diode can reduce the negative pulse going into the CS pin of the CoolSET™
and reduce the abnormal behavior of the CoolSET™. The diode can be a fast speed diode such as 1N4148.
The principle behind is to drain the high surge voltage from Live/Neutral to Ground without passing through
the sensitive components such as the primary controller, IC11.
Data Sheet
42
V2.0, 2014-01-20
w w w . i nf i n eo n. com
Published by Infineon Technologies AG
Similar pages