Panasonic MN101E16 Buzzer output. high-current drive port Datasheet

MN101E16 Series
MN101E16K
Type
MN101E16Y
256K
ROM (byte)
RAM (byte)
Package (Lead-free)
Minimum Instruction
Execution Time
MN101EF16K
Mask ROM
Internal ROM type
MN101EF16Z
FLASH
384K
260K
512K
12K
20K
16K
30K
LQFP100-P-1414,
LQFP100-P-1414,
QFP100-P-1818B
QFP100-P-1818B
QFP100-P-1818B
QFP100-P-1818B
0.0588 µs (at 2.7 V to 3.6 V, 17 MHz, at internal 2, 4, 8 times oscillation))
0.1 µs (at 2.7 V to 3.6 V, 20 MHz)
30.6 µs (at 2.7 V to 3.6 V, 32.768 kHz)
 Interrupts
RESET. Watchdog. External 0 to 5. Timer 0 to 3. Timer 6. Timer 7 (2 systems). Timer A to E.Time base. Serial 0 (2 systems). Serial 1 (2
systems). Serial 2. Serial 3 (2 systems). Serial 4 (2 systems). Automatic transfer finish (2 systems). A/D conversion finish. Key interrupt
 Timer Counter
8-bit timer × 10
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Real time output control
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event. Pulse width measurement. Real time
output control. Serial baud rate timer
Timer 3 ..................Square-wave output. Event count. Serial baud rate timer
Timer 6 ..................8-bit freerun timer. Time base timer
Timer A, B, C, D, E
Timer 0, 1 can be cascade-connected
Timer 0, 1, 2 can be cascade-connected
Timer 2, 3 can be cascade-connected
Timer 0, 1, 2, 3 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output event. Pulse
width measurement. Input capture
Time base timer: One-minute count setting
Watchdog timer × 1
 Serial interface
Synchronous type/UART (full-duplex) × 3: Serial 0, 1, 4
Synchronous type/Single-master I2C × 1: Serial 2
Synchronous type/I2C × 1: Serial 3
 DMA controller
Number of channels: 2 channels
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer
 I/O Pins
I/O
22 : (5 V I/F port) Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
62 : (3 V I/F port) Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
1 : (3 V I/F port) Common use
 A/D converter
10-bit × 8 channels (with S/H)
 Special Ports
Buzzer output. High-current drive port
 ROM Correction
Correcting address designation: Up to 7 addresses possible
MAD00046LEM
MN101E16K, MN101E16Y, MN101EF16K, MN101EF16Z
 Pin Assignment
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
P43
P42, SBT4
P41, SBI4, RXD4
P40, SBO4, TXD4
P87, LED7, D7
P86, LED6, D6
P85, LED5, D5
P84, LED4, D4
P83, LED3, D3
P82, LED2, D2
P81, LED1, D1
P80, LED0, D0
VSS
P77, SD7, NDK
P76, SD6, NWE
P75, SD5, NRE
P74, SD4, NCS
P73, SD3, A19
P72, SD2, A18
P71, SD1, A17
P70, SD0, A16
P67, KEY7, A15
P66, KEY6, A14
P65, KEY5, A13
P64, KEY4, A12
LQFP100-P-1414, QFP100-P-1818B
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
SBO0A, TXD0A, P00
SBI0A, RXD0A, P01
SBT0A, P02
SBO2A, SDA2A, P03
SBI2A, P04
SBT2A, SCL2A, P05
BUZZER, P06
TM0IO, P10
TM1IO, P11
TM2IO, P12
MMOD
OSC2
OSC1
VSS
XI
XO
VDD33
VDD18
NRST, P27
TM3IO, P13
TM7IOA, P14
TM7OB, P15
TM7OC, P16
SYSCLK, P17
IRQ0A, P20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
SBO0B, TXD0B, P90
SBI0B, RXD0B, P91
SBT0B, P92
SBO3B, SDA3B, P93
SBI3B, P94
SBT3B, SCL3B, P95
SBO2B, SDA2B, PD0
SBI2B, PD1
SBT2B, SCL2B, PD2
IRQ0B, PD3
IRQ1B, PD4
IRQ2B, PD5
IRQ3B, PD6
VDD5
PD7
VSS
AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5
AN6, PA6
AN7, PA7
VREF+
MAD00046LEM
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
P63, KEY3, A11
P62, KEY2, A10
P61, KEY1, A9
P60, KEY0, A8
P57, A7
P56, A6
P55, A5
P54, A4
P53, A3
P52, A2
P51, A1
VSS
P50, A0
VDD18
P35, SBT3A, SCL3A
P34, SBI3A
P33, SBO3A, SDA3A
P32, SBT1
P31, SBI1, RXD1
P30, SBO1, TXD1
P25, IRQ5
P24, IRQ4
P23, IRQ3A
P22, IRQ2A
P21, IRQ1A
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any
other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any
other company which may arise as a result of the use of technical information described in this book.
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
– Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body.
– Any applications other than the standard applications intended.
(4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company.
20080805
Similar pages