Through Hole Lamp Product Data Sheet LTL916SYKSA Spec No.: DS20-2008-0119 Effective Date: 07/09/2011 Revision: C LITE-ON DCC RELEASE BNS-OD-FC001/A4 LITE-ON Technology Corp. / Optoelectronics No.90,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C. Tel: 886-2-2222-6181 Fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Piranha LEDs LTL916SYKSA Selection Guide Part No. Color Φv (lm) VA(deg.) λd(nm) LTL916SYKSA Yellow 10.0 40 594 Benefits Fewer LEDs Required Lower lighting System Cost Applications Automotive Lighting Signs and Signals Room Lighting Part No. : LTL916SYKSA BNS-OD-C131/A4 Page : 1 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Features High Current Operation High Flux Output Low Thermal Resistance Low Profile Uniform Light Pattern Meet SAE/ ECE/ JIS Automotive Color Requirement Tube Package for Automatic Loading and Insertion Process Description These parts are designed for high current operation and high flux output applications. In order to solve the high temperature produced by the higher current operation, the package’s design features better thermal management characteristics than other LED solutions coupled with an efficient optical design. This package design allows the lighting designer to reduce the number of LEDs required as well as the overall lighting system cost. The low profile package can be easily coupled to reflectors or lenses to efficiently distribute light and provide the desired illuminated appearance. This product family employs the world’s brightest red, red-orange, amber, blue, cyan, green, and white LED materials etc., which allow designers to match the color of popular lighting applications, such as automotive lighting and electronic signs. Devices Part No. LTL916SYKSA Part No. : LTL916SYKSA BNS-OD-C131/A4 Lens Water Clear Source Color AlInGaP Yellow Page : 2 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Package Dimensions NOTES: 1. All dimensions are in millimeters (inches). 2. Protruded resin is 1.0mm (.04") max. 3. Lead spacing is measured where the leads emerge from the package. 4. Specifications are subject change to without notice. 5. Lead frame: Copper with plating Ag. Part No. : LTL916SYKSA BNS-OD-C131/A4 Page : 3 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Absolute Maximum Ratings at TA=25°C Parameter Maximum Rating Unit Power Dissipation 238 mW DC Forward Current 70 mA 100 mA 1.125 mA /°C 10 V Peak Forward Current (1/10 Duty Cycle,10ms Pulse Width) AlInGaP Derating Linear From 60°C <Note3> Reverse Voltage (IR = 100µA) Operating Temperature Range -40°C to + 100°C Storage Temperature Range -55°C to + 100°C LED Junction Temperature 125°C Soldering Preheat Temperature Lead Soldering Temperature 100°C for 60 Seconds 260°C for 5 Seconds [2.0mm (.0787”) From Seating Plane] Notes: 1. Operation at currents below 10mA is not recommended. 2. Operation in reverse bias is not recommended. 3. Derating linear as shown in Fig. 2 Part No. : LTL916SYKSA BNS-OD-C131/A4 Page : 4 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Electrical / Optical Characteristics at TA=25°C Parameter Total Flux <Note1> Viewing Angle <Note2, Fig 5> Peak Emission Wavelength <Fig 1> Dominant Wavelength Symbol Min. Typ. Max. Unit Test Condition Øv 5.3 10.0 14.8 lm IF=70mA 2θ1/2 40 deg IF=70mA λp 596 nm IF=70mA λd 586 594 599 nm IF=70mA Forward Voltage VF 2.0 2.4 3.0 V IF=70mA Reverse Current IR 10 μA <Note 3> Thermal resistance Note: RθJ-P 125 VR=5V °C /W 1. Ø v is the total luminous flux output as measured with an integrating sphere. 2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single Wavelength which defines the color of the device. Part No. : LTL916SYKSA BNS-OD-C131/A4 Page : 5 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Typical Electrical / Optical Characteristics Curves Part No. : LTL916SYKSA BNS-OD-C131/A4 Page : 6 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Bin Table Specification Note: Tolerance of each bin limit is ±15% Note: Tolerance of each bin limit is ±0.1v Note: Tolerance of each bin limit is ±1nm Part No. : LTL916VEKSA BNS-OD-C131/A4 Page : 7 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Packing Spec 1. Tube: 65pcs Dim: 520mm x 10.1mm x 13.3mm Anti rust Bags: 11 Tubes x 1 Tubes x 65pcs = 715pcs Dim: 700mm x 130mm x Thickness 0.1mm 2. Inner carton: 11 Anti rust bags x 11 Tubes x 65pcs = 7,865 pcs Dim: 530mm x 175mm x 128mm 3. Outer carton: 4 Inner cartons x 7,865 pcs = 31,460 pcs Dim: 545mm x 370mm x 280mm Part No. : LTL916SYKSA BNS-OD-C131/A4 Page : 8 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only CAUTIONS 1. Application The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).Consult Liteon’s Sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. Storage The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity. It is recommended that LEDs out of their original packaging are used within 168 hours (7days). For extended storage out of their original packaging, it must be stored in a sealed container with appropriate desiccant or in desiccators with nitrogen ambient. Liteon lead frames are copper alloy with silver plated. The silver surface may be affected by environments which contain corrosive substances. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the LEDs be used as soon as possible. Please avoid rapid transitions in ambient temperature, especially, in high humidity environment where condensation can occur. 3. Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary. 4. Lead Forming & Assembly During lead forming, the leads should be bent at a point at least 3mm from the base of LED lens. Do not use the base of the lead frame as a fulcrum during forming. Lead forming must be done before soldering, at normal temperature. During assembly on PCB, use minimum clinch force possible to avoid excessive mechanical stress. 5. Soldering When soldering, leave a minimum of 2.0mm clearance from the base of the lens to the soldering point. Dipping the lens into the solder must be avoided. Do not apply any external stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering conditions : Soldering iron Temperature 300°C Max. Soldering time 3 sec. Max. (one time only) Wave soldering Pre-heat 100°C Max. Pre-heat time 60 sec. Max. Solder wave 260°C Max. Soldering time 5 sec. Max. Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED. IR re-flow is not suitable process for through whole type Piranha LED production. Part No. : LTL916SYKSA BNS-OD-C131/A4 Page : 9 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only The suggesting soldering conditions are listed in table which is on page 9. The wave solder temperature profile which is showed as below figure is taken on the bottom side of the PCB board. Both of the suggesting and maximum conditions are all shown in the figure as below. W a v e S o ld e r T e m p e ra tu re P ro file 280 Peak 2.5sec (Timemax=5sec) 240 235℃(Tempmax=260℃) o T e m p e ra tu re ( C ) 200 160 Preheat 30±5sec (Timemax=60sec) 120 85±15℃(Tempmax=100℃) 80 40 0 0 8 16 24 32 40 48 56 T im e (S e c ) Part No. : LTL916SYKSA BNS-OD-C131/A4 Page : 10 of 12 64 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 6. Drive Method An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each LED as shown in Circuit A below. Circuit model A LED Circuit model B LED (A) Recommended circuit (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs 7. ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage: Use a conductive wrist band or anti- electrostatic glove when handling these LEDs All devices, equipment, and machinery must be properly grounded Work tables, storage racks, etc. should be properly grounded Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic lens as a result of friction between LEDs during storage and handing ESD-damaged Leeds will exhibit abnormal characteristics such as high reverse leakage current, low forward voltage, or “no light up” at low currents. To verify for ESD damage, check for “light up” and Vf of the suspect LEDs at low currents. The Vf of “good” LEDs should be >[email protected] for InGaN product and >[email protected] for AlInGaP product. Part No. : LTL916SYKSA BNS-OD-C131/A4 Page : 11 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Suggested checking list : Training and Certification 1. Everyone working in a static-safe area is ESD-certified? 2. Training records kept and re-certification dates monitored? Static-Safe Workstation & Work Areas 1. Static-safe workstation or work-areas have ESD signs? 2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V? 3. All ionizer activated, positioned towards the units? 4. Each work surface mats grounding is good? Personnel Grounding 1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. If conductive footwear used, conductive flooring also present where operator stand or walk? 3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*? 4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DSL? 5. All wrist strap or heel strap checkers calibration up to date? Note: *50V for Blue LED. Device Handling 1. Every ESDS items identified by EIA-471 labels on item or packaging? 2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe workstation? 3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? 8. Others The appearance and specifications of the product may be modified for improvement, without prior notice. Liteon may make process or materials changes affecting the performance or other characteristics of our products. These products supplied after such changes will continue to meet published specifications, but may not be identical to products supplied as samples or under prior orders. Part No. : LTL916SYKSA BNS-OD-C131/A4 Page : 12 of 12