TI DLPA200 15 Dlpa200 dlpâ® dmd micromirror driver9 Datasheet

Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
DLPA200
DLPS015D – APRIL 2010 – REVISED MAY 2015
DLPA200 DLP® DMD Micromirror Driver
1 Features
2 Applications
•
•
•
1
•
•
•
•
•
•
Designed for Use as a Part of a DLP Chipset
Generates the Micromirror Clocking Pulses
Required by the DLP Digital Micromirror Device
(DMD)
Generates Specialized Voltage Levels Required
for Micromirror Clocking Pulse Generation
Operates From a Single 12-V Power Supply
Provides a VBIAS Voltage Level, Used by the DMD
to Control the Array Border Mirrors
Provides a VOFFSET Voltage Level, Used by the
DMD as DMDVCC2
All Logic Inputs are LVTTL and CMOS Compatible
Packaged in an Pb-Free Thermally-Enhanced
Surface-Mount Package: 80-Pin, 0.5 mm-Pitch,
Enlarged Terminal Pitch, Thin Profile Quad Flat
Pack (HTQFP)
Block Diagram
MODE[1:0]
•
•
Industrial:
– Direct Imaging Lithography
– Laser Marking and Repair Systems
– Computer-to-Plate Printers
– Rapid Prototyping Machines and 3D Printers
– 3D Scanners for Machine Vision and Quality
Control
Medical:
– Phototherapy Devices
– Ophthalmology
– Vascular Imaging
– Hyperspectral Imaging
– 3D Scanners for Limb and Skin Measurement
– Confocal Microscopes
Display:
– 3D Imaging Microscopes
– Intelligent and Adaptive Lighting
– Augmented Reality and Information Overlay
2
SEL[1:0]
2
A[3:0]
4
STROBE
Select, Latch,
Output Logic
and
High-Voltage
Output
FET Switches
3 Description
16
OUT(00–15)
OE
The DLPA200 is a DMD micromirror driver that is one
of multiple components in a DLP chipset. A dedicated
DLP chipset provides developers easier access to the
DMD as well as high speed micromirror control.
P12V
Device Information(1)
Internal 5 V
and Ref. Supplies
V5REG
VBIAS_RAIL
VBIAS_LHI
VBIAS
Boost Converter
VBIAS_SWL
VBIAS
VRESET_RAIL (SUBSTRATE)
VRESET
Buck-Boost Converter
VRESET_SWL
PART NUMBER
DLPA200
PACKAGE
HTQFP (80)
BODY SIZE
14.00 mm × 14.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
VRESET
VOFFSET_RAIL
VOFFSET
Regulator
VOFFSET
SCPEN
SCPCK
Serial Bus
Interface
SCPDI
Power-Up Initialization
Fault Logic
IRQ
SCPDO
DEV_ID[1:0]
2
GND
RESET
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
DLPA200
DLPS015D – APRIL 2010 – REVISED MAY 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Device Configurations...........................................
Pin Configuration and Functions .........................
Specifications.........................................................
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
8
1
1
1
2
4
4
7
Absolute Maximum Ratings ...................................... 7
ESD Ratings.............................................................. 7
Recommended Operating Conditions....................... 7
Thermal Information .................................................. 8
Electrical Characteristics Control Logic .................... 8
5-V Linear Regulator................................................. 9
Bias Voltage Boost Converter................................... 9
Reset Voltage Buck-Boost Converter ..................... 10
VOFFSET/DMDVCC2 Regulator................................ 10
Switching Characteristics ...................................... 11
Detailed Description ............................................ 13
8.1 Overview ................................................................. 13
8.2 Functional Block Diagram ....................................... 14
8.3 Feature Description................................................. 15
9
Application and Implementation ........................ 18
9.1 Application Information............................................ 18
10 Power Supply Recommendations ..................... 20
10.1 Power Supply Rail Guidelines............................... 20
11 Layout................................................................... 21
11.1 Layout Guidelines ................................................. 21
11.2 Thermal Considerations ........................................ 21
12 Device and Documentation Support ................. 22
12.1
12.2
12.3
12.4
12.5
12.6
Device Support......................................................
Documentation Support ........................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
22
22
22
22
23
23
13 Mechanical, Packaging, and Orderable
Information ........................................................... 23
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision C (September 2013) to Revision D
•
Page
Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section ................................................................................................. 1
Changes from Revision B (August 2012) to Revision C
Page
•
Added DLPR4101 to DLPR410 througout document............................................................................................................. 4
•
Changed DAD2000 to DLPA200 in the Serial Communications Port (SCP) section........................................................... 17
•
Changed text From: DLPA200PFC is functionally. equivalent.. To: DLPA200PFP ............................................................ 22
Changes from Revision A (June 2010) to Revision B
Page
•
Added Applications ................................................................................................................................................................. 1
•
Changed the Description, added Table 1............................................................................................................................... 1
•
Added Device Configurations table ........................................................................................................................................ 4
•
Changed I/O type of the signals ............................................................................................................................................. 5
•
Corrected VRESET_SWL, VBIAS_RAIL and VOFFSET_RAIL signal notations ................................................................... 7
•
Added VBIAS voltage to Electrical Characteristics ................................................................................................................... 9
•
Added VRESET voltage values to Reset Voltage Buck-Boost Converter................................................................................ 10
•
Added VOFFSET voltage to Electrical Characteristics ............................................................................................................. 10
•
Added subsection Serial Communications Port (SCP) ........................................................................................................ 17
•
Deleted Driver Output Logic Block section........................................................................................................................... 17
•
Added Serial Communications Port Signal Definitions table................................................................................................ 17
•
Changed Warning to Note .................................................................................................................................................... 20
•
Changed Warning to Caution ............................................................................................................................................... 21
2
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
DLPA200
www.ti.com
DLPS015D – APRIL 2010 – REVISED MAY 2015
Changes from Original (April 2010) to Revision A
•
Page
Changed device marking to include TI internal part number................................................................................................ 22
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
3
DLPA200
DLPS015D – APRIL 2010 – REVISED MAY 2015
www.ti.com
5 Device Configurations
DMD
POWER AND MIRROR CLOCKING PULSE DRIVER
DLP9500 (0.95 1080p Type A DMD)
DIGITAL CONTROLLER
DLPA200 (x2)
DLP7000 (0.7 XGA Type A DMD)
DLPA200
DLP5500 (0.55 XGA S450 DMD)
DLPA200
DLPC410
DLPC200
Table 1. Supported DLP Chipset Configurations (1)
0.55 XGA Chipset
0.7 XGA CHIPSET
QTY
TI PART
DESCRIPTION
QTY
TI PART
1
DLP5500
0.55 XGA S450
DMD(digital micromirror
device)
1
DLP7000
DMD Controller for
DLP5500
1
DLPC410
1
1
(1)
QTY
TI PART
DESCRIPTION
0.7 XGA Type A DMD
(digital micromirror
device)
1
DLP9500
0.95 1080p Type A
DMD(digital micromirror
device)
DLP Discovery 4100
DMD Controller
1
DLPC410
DLP Discovery 4100
DMD Controller
1
DLP Discovery 4100
DLPR410
Configuration PROM
/DLPR410
1
1
DLPR410
/
DLPR410
1
DLP Discovery 4100
Configuration PROM
1
DLPA200
2
DLPA200
DMD Micromirror Driver
DLPC200
DLPA200
DMD Micromirror Driver
0.95 1080p CHIPSET
DESCRIPTION
DMD Micromirror Driver
See Overview for more information.
6 Pin Configuration and Functions
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
VBIAS_RAIL
OUT15
VOFFSET_RAIL
OUT14
VRESET_RAIL
VRESET_RAIL
OUT13
VOFFSET_RAIL
OUT12
VBIAS_RAIL
VBIAS_RAIL
OUT11
VOFFSET_RAIL
OUT10
VRESET_RAIL
VRESET_RAIL
OUT09
VOFFSET_RAIL
OUT08
VBIAS_RAIL
PFP Package
80-Pin HTQFP
Top View
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
GND
RESET
SCPEN
SCPDI
SCPCK
GND
NC
G
NC
NC
P12V
VOFFSET
P12V
V5REG
GND
DEV_ID1
DEV_ID0
IRQ
SCPDO
GND
VBIAS_RAIL
OUT00
VOFFSET_RAIL
OUT01
VRESET_RAIL
VRESET_RAIL
OUT02
VOFFSET_RAIL
OUT03
VBIAS_RAIL
VBIAS_RAIL
OUT04
VOFFSET_RAIL
OUT05
VRESET_RAIL
VRESET_RAIL
OUT06
VOFFSET_RAIL
OUT07
VBIAS_RAIL
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
GND
MODE1
MODE0
SEL1
SEL0
OE
GND
VBIAS_SWL
VBIAS
VBIAS_LHI
P12V
VRESET_SWL
VRESET
GND
STROBE
A3
A2
A1
A0
GND
4
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
DLPA200
www.ti.com
DLPS015D – APRIL 2010 – REVISED MAY 2015
Pin Functions
PIN
NO.
I/O
(INPUT
DEFAULT)
OUT00
22
Output
OUT01
24
Output
OUT02
27
Output
OUT03
29
Output
OUT04
32
Output
OUT05
34
Output
OUT06
37
Output
OUT07
39
Output
OUT08
62
Output
OUT09
64
Output
OUT10
67
Output
OUT11
69
Output
OUT12
72
Output
OUT13
74
Output
OUT14
77
Output
OUT15
79
Output
A0
19
Input (pull down)
A1
18
Input (pull down)
A2
17
Input (pull down)
A3
16
Input (pull down)
MODE0
3
Input (pull down)
MODE1
2
Input (pull down)
SEL0
5
Input (pull down)
SEL1
4
Input (pull down)
Output Voltage Select. Used to switch the voltage applied to the addressed OUTxx
pin.
STROBE
15
Input (pull down)
A rising edge on STROBE latches in the control signals after a tri-state delay.
OE
6
Input (pull up)
Asynchronous input controls whether the 16 OUTxx pins are active or are in a in
high-impedance state.
OE = 0 : Enabled. OE = 1 : High Z.
RESET
59
Input (pull up)
Resets the DLPA200 internal logic. Active low. Asynchronous.
SCPEN
58
Input (pull up)
Enables serial bus data transfers. Active low.
SCPDI
57
Input (pull down)
Serial bus data input. Clocked in on the falling edge of SCPCK.
SCPCK
56
Input (pull down)
Serial bus clock. Provided by chipset Controller.
SCPDO
42
Output
Serial bus data output (open drain). Clocked out on the rising edge of SCPCK.
A 1kΩ pull up resistor to the Chip-Set Controller VDD supply is recommended.
IRQ
43
Output
Interrupt request output to the chipset Controller. Active low.
A 1 kΩ pull up resistor to the Chip-Set Controller VDD supply is recommended.
DEV_ID1
45
Input (pull up)
DEV_ID0
44
Input (pull up)
VBIAS
9
Output
VBIAS_LHI
10
Input
Current limiter output for VBIAS supply. (also the VBIAS switching inductor input)
VBIAS_SWL
8
Input
Connection point for VBIAS supply switching inductor.
VBIAS_RAIL
21, 30, 31,
40, 61, 70,
71, 80
Input
The internally-used VBIAS supply rail. Internally isolated from VBIAS.
VRESET
13
Output
VRESET_SWL
12
Input
NAME
DESCRIPTION
16 micromirror clocking waveform outputs (enabled by OE = 0).
Output Address. Used to select which OUTxx pin is active at a given time.
Mode Select. Used to determine the operating mode of the DLPA200.
Serial bus device address:
00 = all; 01 = device 1; 10 = device 2; 11 = device 3.
One of three specialized voltages which are generated by the DLPA200.
One of three specialized voltages which are generated by the DLPA200. The
package thermal pad is tied to this voltage level.
Connection point for VRESET supply switching inductor..
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
5
DLPA200
DLPS015D – APRIL 2010 – REVISED MAY 2015
www.ti.com
Pin Functions (continued)
PIN
I/O
(INPUT
DEFAULT)
NAME
NO.
VRESET_RAIL (1)
25, 26, 35,36,
65, 66, 75,
76
Input
VOFFSET
DESCRIPTION
The internally-used VRESET supply rail. Internally isolated from VRESET. (1)
49
Output
VOFFSET_RAIL
23, 28, 33,
38, 63, 68,
73, 78
Input
The internally-used VOFFSET supply rail. Internally isolated from VOFFSET.
GND
1, 7, 14, 20,
41, 46, 53,
55, 60
GND
Common ground
V5REG
47
Output
P12V
11, 48, 50
Input
NC
51, 52, 54
No Connect
(1)
6
One of three specialized voltages which are generated by the DLPA200.
The 5-volt logic supply output.
The main power input to the DLPA200.
No connect
Exposed thermal pad is internally connected to VRESET_RAIL.
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
DLPA200
www.ti.com
DLPS015D – APRIL 2010 – REVISED MAY 2015
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MAX
UNIT
Load supply voltage, P12V
MIN
14
V
Reset supply switching inductor connection
Measured with respect to VRESET_RAIL
point, VRESET_SWL
–1
V
Internally-used VBIAS supply rail,
VBIAS_RAIL
Measured with respect to VRESET_RAIL
60
V
Internally-used VOFFSET supply rail,
VOFFSET_RAIL
Measured with respect to VRESET_RAIL
40.5
V
VIN
Logic inputs
7
V
VOUT
Open drain logic outputs
TJ
Maximum junction temperature
TA
Operating temperature
Tstg
Storage temperature
(1)
–0.3
7
V
125
°C
0
75
°C
–55
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
7.2 ESD Ratings
VALUE
V(ESD) (1)
(1)
(2)
(3)
Electrostatic
discharge
Human body model (HBM)
(2)
UNIT
±2000
Charged device model (CDM) (3)
V
800
Electrostatic discharge (ESD) to measure device sensitivity and immunity to damage caused by assembly line electrostatic discharges in
to the device.
JEDEC document JEP155 states that 500 V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250 V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
at TA = 25°C, P12V = 10.8 V to 13.2 V (unless otherwise noted) (1)
POWER
IP12V1
P12V supply current (2)
Global shadow at 50 kHz, OUT load = 39 Ω and 390
pF, V5REG = 30 mA, VBIAS = 26 V at 5 mA, VOFFSET
= 10V at 30 mA, VRESET = –26 V
Thermal shutdown temperature
With device temperature rising
Hysteresis
Delta between thermal
shutdown and thermal warning
TJTWR
(1)
(2)
NOM
Thermal warning temperature
With device temperature rising
Hysteresis
MAX
UNIT
200
Outputs disabled and no external loads, VBIAS = 19
V, VOFFSET = 4.5 V, VRESET = –19 V
IP12V2
TJTSDR
MIN
mA
22
mA
145
160
175
°C
5
10
15
°C
5
10
15
°C
125
140
155
°C
5
10
15
°C
The functional performance of the device specified in this data sheet is achieved when operating the device within the limits defined by
the Recommended Operating Conditions. No level of performance is implied when operating the device above or below the
Recommended Operating Conditions limits.
During power up the inrush power supply current can be as high as 1 A for a momentary period of time.
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
7
DLPA200
DLPS015D – APRIL 2010 – REVISED MAY 2015
www.ti.com
7.4 Thermal Information
DLPA200
THERMAL METRIC (1)
PFP (HTQFP)
UNIT
80 PINS
Thermal resistance,
VBIAS = 26 V, VRESET = -26 V, VOFFSET = 10 V,
Output load = 390 pF and 39R on each output,
Phase by one with global mode,
Channel repetition frequency = 50 kHz,
Additional external loads: IBIAS = 5 mA,
IOFFSET = 30 mA, I5REG = 30 mA
Rc-j
(1)
3
°C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
7.5 Electrical Characteristics Control Logic
TA = 25°C, P12V = 10.8 V to 13.2 V (unless otherwise noted)
PARAMETER
VIL
Low-level logic input voltage
VIH
High-level logic input voltage
TEST CONDITIONS
MIN
TYP
MAX
0.8
1.97
UNIT
V
V
IIH
High-level logic input current
VIN = 5 V, input with pulldown. See terminal
functions table.
IIL
Low-level logic input current
VIN = 0 V, input with pullup. See terminal functions
table.
IIH
High-level logic input leakage
current
VIN = 0 V, input with pulldown
–1
1
µA
IIL
Low-level logic input leakage
current
VIN = 5 V, input with pullup
–1
1
µA
VOL
Open drain logic outputs
I = 4 mA
IOL
Logic output leakage current
V = 3.3 V
8
Submit Documentation Feedback
40
–50
50
–40
µA
µA
0.4
V
1
µA
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
DLPA200
www.ti.com
DLPS015D – APRIL 2010 – REVISED MAY 2015
7.6 5-V Linear Regulator
TA = 25°C, P12V = 10.8 V to 13.2 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TYP
MAX
4.75
5
5.25
UNIT
V5REG
Output voltage
IIL
Output current: internal logic
4
20
mA
IIE
Output current: external
circuitry
0
30
mA
ICL5
Current limit
VUV5
Undervoltage threshold
VRIP
Output ripple voltage (1)
VOS5
Voltage overshoot at start up
tss
Power up
(1)
Average voltage, IOUT = 4 mA to 50 mA
MIN
V
80
IOUT = 50 mA
mA
V5REG voltage increasing, P12V
= 5.4 V
4.1
V5REG voltage falling, P12V =
5.2 V
3.9
V
Measured between 10 to 90% of V5REG
200
mVpk-pk
2
%V5REG
1
ms
Output ripple voltage relies on suitable external components being selected and good printed circuit board layout practice.
7.7 Bias Voltage Boost Converter
TA = 25°C, P12V = 10.8 V to 13.2 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
IRL
Output current: reset outputs
Load = 400pF, 39 Ω,
repetition frequency = 50 kHz
IQL
Output current: quiescent /
drivers
Load = 400 pF, 39 Ω,
repetition frequency = 50 kHz
IDL
Output current: DMD load
ICLFB
Current limit flag
Corresponding current on output at P12V = 10.8 V
ICLB
Current limit
Measured on input
VBIAS
Output voltage
VUVB
VBIAS undervoltage threshold
Bias voltage falling
VUVLHI
VBIAS_LHI undervoltage
threshold
VBIAS_LHI voltage increasing
RDS
Boost switch RDS(on)
TJ = 25°C
VRIP
Output ripple voltage (1)
FSW
Switching frequency
VOSB
Voltage overshoot at start up
tss
Power up
tdis
Discharge current sink
(1)
MIN
TYP
0
MAX UNIT
18
mA
3
mA
5
mA
0
30
mA
330
376
460
25.5
26
26.5
50
92
mA
V
%VBIAS
8
VBIAS_LHI voltage falling
V
6.5
V
2
Ω
200
1.35
1.5
1.65
COUT = 3.3 µF, Measured between 10 to 90% of
target VBIAS
mVpk-pk
MHz
2
%VBIAS
1
ms
400
mA
Output ripple voltage relies on suitable external components being selected and good printed circuit board layout practice.
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
9
DLPA200
DLPS015D – APRIL 2010 – REVISED MAY 2015
www.ti.com
7.8 Reset Voltage Buck-Boost Converter
TA = 25°C, P12V = 10.8 V to 13.2 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
IRL
Output current: reset outputs
Load = 400 pF, 39 Ω,
repetition frequency = 50 kHz
IQL
Output current: quiescent / drivers
Load = 400 pF, 39 Ω ,
repetition frequency = 50 kHz
ICLFR
Current limit flag
Corresponding current on output at
P12V = 10.8 V
ICLR
Current limit
Measured on input
VRESET
Output voltage
VUVR
Undervoltage threshold
Reset voltage falling
RDS
Buck-boost switch RDS(on)
TJ = 25°C
VRIP
Output ripple voltage (1)
FSW
Switching frequency
VOSR
Voltage overshoot at start up
tss
Power up
tdis
Discharge current sink
(1)
MIN
TYP
0
MAX
18
mA
3
mA
25
mA
400
–25.5
800
–26
50
–26.5
mA
V
92 %VRESET
Ω
8
1.35
UNIT
1.5
200
mVpk-pk
1.65
MHz
2 %VRESET
COUT = 3.3 µF, Measured between 10 to 90% of
target VRESET
1
400
ms
mA
Output ripple voltage relies on suitable external components being selected and good printed circuit board layout practice.
7.9 VOFFSET/DMDVCC2 Regulator
TA = 25°C, P12V = 10.8 V to 13.2 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
IRL
Output current: reset
outputs
Load = 400 pF, 39 Ω, repetition frequency = 50 kHz
IQL
Output current: quiescent /
drivers
Load = 400 pF, 39 Ω, repetition frequency = 50 kHz
IDL
Output current: DMDVCC2
ICLO
Current limit
VOFFSET
Output Voltage
VUVO
Undervoltage threshold
0
UNIT
12.2
mA
3
mA
30
mA
VOSO
Voltage overshoot at startup
tss
Power up
tdis
Discharge time constant
mA
DLP9500, DLP5500
8.25
8.5
8.75
DLP7000
7.25
7.5
7.75
VOFFSET voltage falling
50
(1)
Output ripple voltage
10
0
MAX
100
VRIP
(1)
TYP
V
92 %VOFFSET
100
mVpk-pk
2 %VOFFSET
COUT = 4.7 µF, Measured between 10 to 90% of target
VOFFSET
1
ms
100
μs
Output ripple voltage relies on suitable external components being selected and good printed circuit board layout practice.
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
DLPA200
www.ti.com
DLPS015D – APRIL 2010 – REVISED MAY 2015
7.10 Switching Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
UNIT
SERIAL COMMUNICATION PORT INTERFACE
A (1)
Setup SCPEN low to SCPCK
Reference to rising edge of SCPCK
360
ns
B (1)
Byte to byte delay
Nominally 1 SCPCK cycle, rising edge to rising edge
1.9
µs
C (1)
Setup SCPDI to SCPEN high
Last byte to slave disable
360
ns
D
(1)
SCPCK frequency
E (1)
F
(1)
(2)
0
526
1.9
SCPCK high or low time
300
ns
ns
SCPDI set-up time
Reference to falling edge of SCPCK
300
G (1)
SCPDI hold time
Reference from falling edge of SCPCK
300
H (1)
SCPDO propagation delay
Reference from rising edge of SCPCK
2
kHz
SCPCK period
µs
ns
300
SCPEN, SCPCK, SCPDI, RESET
filter (pulse reject)
150
ns
ns
OUTPUT MICROMIRROR CLOCKING PULSES
FPREP
Phased reset repetition frequency
each output pin (non-overlapping)
50
kHz
FGREP
Global reset repetition frequency all
output pins
50
kHz
IRLK
VRESET output leakage current
OE = 1, VRESET_RAIL = -28.5V
-1
-10
µA
IBLK
VBIAS output leakage current
OE = 1, VBIAS_RAIL = 28.5V
1
10
µA
IOLK
VOFFSET output leakage current
OE = 1, VOFFSET_RAIL = 10.25V
1
10
µA
OUTPUT MICROMIRROR CLOCKING PULSE CONTROLS
tSPW
STROBE pulse width
10
tSP
STROBE period
20
tOHZ
Output time to high impedance
OE Pin = High
100
ns
tOEN
Output enable time from high
impedance
OE Pin = Low
100
ns
tSUS
Set-up time
From A[3:0], MODE[1:0], and SEL[1:0] to STROBE edge
8
ns
tHOS
Hold time
From A[3:0], MODE[1:0], and SEL[1:0] to STROBE edge
8
ns
tPBR
tPRO
Propagation time
tPOB
ns
ns
From STROBE to VBIAS/VRESET edge 50% point.
80
200
ns
From STROBE to VRESET/VOFFSET edge 50% point.
80
200
ns
From STROBE to VOFFSET/VBIAS edge 50% point.
80
200
ns
tDEL
Edge-to-edge propagation delta
Maximum difference between the slowest and fastest
propagation times for any given reset output.
40
ns
tCHCH
Output channel-to-channel
propagation delta
Maximum difference between the slowest and fastest
propagation times for any two outputs for any given edge.
20
ns
(1)
(2)
See Figure 1
There is no minimum speed for the serial port. It can be written to statically for diagnostic purposes.
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
11
DLPA200
DLPS015D – APRIL 2010 – REVISED MAY 2015
www.ti.com
SCPEN
D
A
E
B
Clock 1
Byte 1
SCPCK
F
SCPDI
C
E
X
Clock 2
Byte 1
G
F
X
H
Clock 3
Byte 1
Clock 8
Byte 1
Clock 1
Byte 2
G
F
X
X
X
H
Clock 8
Last byte
G
X
H
SCPDO
X = Don’t care
Figure 1. Serial Interface Timing
12
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
DLPA200
www.ti.com
DLPS015D – APRIL 2010 – REVISED MAY 2015
8 Detailed Description
8.1 Overview
Reliable function and operation of the DLPA200 requires that it be used in conjunction with the other components
of the chipset. It is typical for the DMD controller to operate the DMD micromirror driver. For more information on
the chipset components, see the DLP 0.55 XGA Chipset data sheet or DLP Discovery 4100 Chipset data sheet
(Table 8).
The DLPA200 consists of three functional blocks: A High-Voltage Power Supply function, a DMD Micromirror
Clock Generation function, and a Serial Communication function.
The High-Voltage Power Supply function generates three specialized voltage levels: VBIAS (19 to 28 V), VRESET
(–19 to –28 V), and VOFFSET (4.5 to 10 V).
The Micromirror Clock Generation function uses the three voltages generated by the High-Voltage Power Supply
function to create the sixteen micromirror clock pluses (output the OUTx pins of the DLPA200).
The Serial Communication function allows the chipset Controller to control the generation of VBIAS, VRESET, and
VOFFSET; control the generation of the micromirror clock pulses; status the general operation of the DLPA200.
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
13
DLPA200
DLPS015D – APRIL 2010 – REVISED MAY 2015
www.ti.com
8.2 Functional Block Diagram
MODE[1:0]
2
SEL[1:0]
Select, Latch,
Output Logic
and
High-Voltage
Output
FET Switches
2
A[3:0]
4
STROBE
16
OUT(00–15)
OE
P12V
Internal 5 V
and Ref. Supplies
V5REG
VBIAS_RAIL
VBIAS_LHI
VBIAS
Boost Converter
VBIAS_SWL
VBIAS
VRESET_RAIL (SUBSTRATE)
VRESET
Buck-Boost Converter
VRESET_SWL
VRESET
VOFFSET_RAIL
VOFFSET
Regulator
VOFFSET
SCPEN
SCPCK
Serial Bus
Interface
SCPDI
Power-Up Initialization
Fault Logic
IRQ
SCPDO
DEV_ID[1:0]
2
GND
RESET
14
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
DLPA200
www.ti.com
DLPS015D – APRIL 2010 – REVISED MAY 2015
8.3 Feature Description
8.3.1 5-V Linear Regulator
The 5-V linear regulator supplies the 5-V requirement of the DLPA200 internal logic.
Figure 2 shows the block diagram of this module. The input decoupling capacitors are shared with other internal
DLPA200 modules. See Component Selection Guidelines for recommended component values.
5 V Linear
Regulator
P12V
V5REG
GND
Figure 2. 5-Volt Linear Regulator Block Diagram
8.3.2 Bias Voltage Boost Converter
The bias voltage converter is a switching supply that operates at 1.5 MHz. The bias switching device switches
180° out-of-phase with the reset switching device.
The converter supplies the internal bias voltage for the high voltage FET switches and the external VBIAS for the
DMD border mirrors. The VBIAS voltage level can be different for different generations of DMDs. The VBIAS voltage
level is configured by the DLP Controller chip over a serial communication interface. Four control bits select the
voltage level while a fifth bit is the on/off control. The module provides two status bits to indicate latched and
unlatched status bits for under-voltage (VUV) and current-limit (CL) conditions.
Figure 3 shows the block diagram of this module. The input decoupling capacitors are shared with other internal
DLPA200 modules. See Component Selection Guidelines for recommended component values.
Inductor
VBIAS_LHI
VBIAS_SWL
P12V
VBIAS
V5REG
BGAP REF
OSC
BIAS
STATUS
Serial Interface
and Control
BIAS
CONTROL
Bias Boost
Converter and
Current Limit
2
4
ENABLE
GND
Figure 3. Bias Voltage Boost Converter Block Diagram
8.3.3 Reset Voltage Buck-Boost Converter
The reset voltage buck-boost converter is a switching supply that operates at 1.5 MHz. The reset switching
device switches 180° out-of-phase with the bias switching device.
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
15
DLPA200
DLPS015D – APRIL 2010 – REVISED MAY 2015
www.ti.com
Feature Description (continued)
The converter supplies the internal reset voltage levels for the high voltage FET switches. The VRESET voltage
level can be different for different generations of DMDs. The VRESET voltage level is configured by the DLP
controller chip over a serial communication interface. Four control bits select the voltage level while a fifth bit is
the on/off control. The module provides two status bits to indicate latched and unlatched status bits for undervoltage (VUV) and current-limit (CL) conditions.
Figure 4 shows the block diagram of this module. The input decoupling capacitors are shared with other internal
DLPA200 modules. See Component Selection Guidelines for recommended component values.
P12V
SWL
VRESET
V5REG
BGAP REF
OSC
Serial Interface
and Control
RESET
STATUS
Reset Buck-Boost
Converter and
Current Limit
VRESET_SWL
2
RESET
CONTROL
4
Inductor
ENABLE
GND
Figure 4. Reset Voltage Buck-Boost Converter Block Diagram
8.3.4 VOFFSET/DMDVCC2 Regulator
The VOFFSET/DMDVCC2 regulator supplies the internal VOFFSET voltage for the high voltage FET switches and the
external DMDVCC2 for the DMD. The VOFFSET voltage level can be different for different generations of DMDs.
The VOFFSET voltage level is configured by the DLP Controller chip over a serial communication interface. Four
control bits select the voltage level while a fifth bit is the on/off control. The module provides 2 status bits to
indicate latched and unlatched status bits for under-voltage (VUV) and current-limit (CL) conditions.
Figure 5 shows the block diagram of this module. The input decoupling capacitors are shared with other
DLPA200 modules. See Component Selection Guidelines for recommended component values.
P12V
VOFFSET
DMDVCC2
V5REG
BGAP REF
VOFFSET Linear
Serial Interface
and Control
OFFSET
STATUS
2
Regulator and
Current Limit
OFFSET
CONTROL
4
ENABLE
GND
Figure 5. Offset Voltage Boost Convertor Block Diagram
16
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
DLPA200
www.ti.com
DLPS015D – APRIL 2010 – REVISED MAY 2015
Feature Description (continued)
8.3.5 Serial Communications Port (SCP)
The SCP is a full duplex, synchronous, character-oriented (byte) port that allows exchange of data between the
master ASIC or FPGA, and one or more slave DLPA200s (and/or other DLP devices).
Table 2. Serial Communications Port Signal Definitions
SIGNAL
SCPCK
I/O
I
FROM/TO
SCP bus master to slave
TYPE
DESCRIPTION
LVTTL compatible
SCP bus serial transfer clock. The host processor
(master) generates this clock.
SCPEN
I
SCP bus master to slave
LVTTL compatible
SCP bus access enable (low true). When high, slave
will reset to idle state, and SCPDO output will tristate. Pulling SCPEN low initiates a read or write
access. SCPEN must remain low for an entire
read/write access, and must be pulled high after the
last data cycle. To abort a read or write cycle, pull
SCPEN high at any point.
SCPDI
I
SCP bus master to slave
LVTTL compatible
SCP bus serial data input. Data bits are valid and
must be clocked in on the falling edge of SCPCK.
SCPDO
O
SCP bus slave to master
IRQ
O
SCP bus slave to master
SCP bus serial data output. Data bits must clocked
LVTTL, open drain w/tri-state out on the rising edge of SCPCK. A 1-kΩ pullup
resistor to the 3.3 volt ASIC supply is required.
LVTTL, open drain
Not part of the SCP bus definition. Asynchronous
interrupt signal from slave to request service from
master. A 1-kΩ pullup resistor to the 3.3-V ASIC
supply is required.
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
17
DLPA200
DLPS015D – APRIL 2010 – REVISED MAY 2015
www.ti.com
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
9.1.1 Component Selection Guidelines
Table 3. 5-V Regulator
COMPONENT
VALUE
TYPE OR PART
NUMBER
CONNECTION 1
CONNECTION 2
P12V filter capacitor
10 to 33 µF, 20 VDC,
1Ω max ESR
Tantalum or ceramic
Pos: P12V, pin 11
(locate near pin 11)
Neg: Ground
P12V bypass capacitor
0.1 µF, 50 VDC,
0.1Ω max ESR
Ceramic
P12V, pin 11
(locate near pin 11)
Ground
V5REG filter capacitor
0.1 (1) to 1.0 µF, 10 VDC,
2.5Ω max ESR
Tantalum or ceramic
Pos: V5REG, pin 47
(locate near pin 47)
Neg: Ground
Ceramic
V5REG, pin 47
(locate near pin 47)
Ground
(1)
V5REG bypass capacitor
(1)
0.1 µF , 16 VDC,
0.1Ω max ESR
To ensure stability of the linear regulator, the capacitance should not be less than 0.1 µF.
Table 4. Bias Voltage Boost Converter
COMPONENT
VALUE
TYPE OR PART
NUMBER
CONNECTION 1
CONNECTION 2
LHI filter capacitor
10 µF, 20 VDC,
1Ω max ESR
Tantalum or ceramic
Pos: VBIAS_LHI, pin 10
(locate near pin 10)
Neg: Ground
LHI bypass capacitor
0.1 µF, 50 VDC,
0.1Ω max ESR
Ceramic
VBIAS_LHI, pin 10
(locate near pin 10)
Ground
VBIAS filter capacitor
1 to 10 µF, 35 VDC,
1Ω max ESR;
(3.3 µF nominal value)
Tantalum or ceramic
Pos: VBIAS, pin 9
(locate near pin 9)
Neg: Ground
VBIAS bypass capacitor
0.1 µF, 50 VDC,
0.1Ω max ESR
Ceramic
VBIAS, pin 9
(locate near pin 9)
Ground
VBIAS_RAIL bypass
capacitors (2 required)
0.1 µF, 50 VDC,
0.1Ω max ESR
Ceramic
VBIAS_RAIL, pins 30 and 71
(locate near pins 30 and 71)
Ground
Resistor jumper (optional)
0-Ω normally
(1Ω for testing (1))
VBIAS, pin 9
VBIAS_RAIL,
pins 21 or 80
Inductor
22 µH, 0.5 amp,
160 mΩ ESR
Coil Craft DT1608C-223
(or equivalent)
VBIAS_LHI, pin 10
VBIAS_SWL, pin 8
0.5A, 40V (minimum)
Motorola MBR0540T1 or
STMicroelectronics
STPS0540Z, STPS0560Z
(or equivalent)
Anode:
VBIAS_SWL, pin 8
Cathode:
VBIAS, pin 9
Schottky diode
(1)
Allows for VBIAS current measurement.
18
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
DLPA200
www.ti.com
DLPS015D – APRIL 2010 – REVISED MAY 2015
Table 5. Reset Voltage Boost Converter
COMPONENT
VALUE
TYPE OR PART
NUMBER
CONNECTION 1
CONNECTION 2
VRESET filter capacitor
1 to 10 µF, 35 VDC,
1Ω max ESR;
(3.3 µF nominal value)
Tantalum or ceramic
Neg: VRESET, pin 13
(locate near pin 13)
Pos: Ground
VRESET bypass capacitor
0.1 µF, 50 VDC,
0.1Ω max ESR
Ceramic
VRESET, pin 13
(locate near pin 13)
Ground
VRESET_RAIL bypass
capacitors (2 required)
0.1 µF, 50 VDC,
0.1Ω max ESR
Ceramic
VRESET_RAIL,
pins 35 and 66
(locate near pins 35 and 66)
Ground
Resistor jumper (optional)
0-Ω normally
(1Ω for testing (1))
VRESET, pin 13
VRESET_RAIL,
pins 25 or 76
Inductor
22 µH, 0.5A,
160 mΩ
Coil Craft DT1608C-223
(or equivalent)
VRESET_SWL, pin 12
Ground
Schottky diode
0.5 A (minimum), 60 V
STMicroelectronics
STPS0560Z or
International Rectifier
10MQ060N (or equivalent)
Cathode:
VRESET_SWL, pin 12
Anode:
VRESET, pin 13
(1)
Allows for VRESET current measurement.
Table 6. Offset Voltage Regulator
(1)
(2)
(3)
(4)
COMPONENT
VALUE
TYPE OR PART
NUMBER
CONNECTION 1
CONNECTION 2
VOFFSET/VCC2
filter capacitors
(2 required)
1 (1) to 4.7 (2) µF, 35 VDC,
1Ω max ESR
Tantalum or ceramic
Pos: VOFFSET, pin 49
(1st near pin 49)
Pos: DMDVCC2 pins
(locate 2nd at DMD)
Neg: Ground at DLPA200
Neg: Ground at DMD
VOFFSET/VCC2
bypass capacitors
(5 required)
0.1 µF, 50 VDC,
0.1Ω max ESR
Ceramic
VOFFSET, pin 49
(locate 1 near pin 49)
DMD DMDVCC2 pins
(locate 4 near DMD pins)
Ground at DLPA200
Ground at DMD
VOFFSET_RAIL
bypass capacitor
(2 required)
0.1 µF, 50 VDC,
0.1Ω max ESR
Ceramic
VOFFSET_RAIL,
pins 28 and 73
(locate near pins 28 and
73)
Ground
Resistor jumper
(optional)
0-Ω normal
(1Ω for testing (3))
VOFFSET, pin 49
VOFFSET_RAIL,
pins 38 or 63
Resistor jumper
(optional)
0-ohm normal
(1Ω for testing (4))
VOFFSET, pin 49
DMDVCC2 pins
To ensure stability of the linear regulator, the absolute minimum output capacitance should not be less than 1.0 µF.
Recommended value is 3.3 µF each. Different values are acceptable, provided that the sum of the two is 6.8 µF maximum.
Allows for VOFFSET current measurement
Allows for DMDVCC2 current measurement
Table 7. Pullup Resistors
COMPONENT
VALUE
TYPE OR PART NUMBER
CONNECTION 1
CONNECTION 2
Resistor
1 kΩ
SCPDO, pin 42
Chipset controller
3.3-V VDD
Resistor
1 kΩ
IRQ, pin 43
Chipset Controller
3.3-V VDD
Resistor (optional)
1 kΩ
OE, pin 6
Chipset Controller
3.3-V VDD
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
19
DLPA200
DLPS015D – APRIL 2010 – REVISED MAY 2015
www.ti.com
10 Power Supply Recommendations
10.1 Power Supply Rail Guidelines
Table 3 through Table 7 provides discrete component selection guidelines.
The P12V filter and bypass capacitors should be distributed and connected to pin 11 and pins 48 & 50. These
capacitors should be placed as near to their respective pins as possible and if necessary, should be placed on
the bottom layer.
The V5REG filter and bypass capacitors must be placed near and connected to pin 47.
The VBIAS_RAIL etch runs should be routed in the following order: pin 40, pin 31, pin 30, pin 21, pin 80, pin 71,
pin 70, and pin 61. The etch runs should be short and direct as they must carry 35 ns current spikes of up to
0.64 amps peak. Bypass capacitors should be located near and connected to pins 30 and 71 to provide
bypassing on both sides.
The VBIAS_LHI filter and bypass capacitors must be placed near and connected to pin 10.
The VBIAS filter and bypass capacitors must be placed near and connected to pin 9. VBIAS pin 9 must also be
connected (optionally with a 0-ohm resistor) to VBIAS_RAIL at or between pins 21 and 80.
The VRESET_RAIL etch runs should be routed in the following order: pin 36, pin 35, pin 26, pin 25, pin 76, pin
75, pin 66, and pin 65. The etch runs should be short and direct as they must carry 35 ns current spikes of up to
0.64 amps peak. Bypass capacitors should be placed near and connected to pins 35 and 66 to provide
bypassing on both sides.
The VRESET filter and bypass capacitors must be located near and connected to pin 13. VRESET pin 13 must
also be connected (optionally with a 0-ohm resistor) to VRESET_RAIL at or between pins 25 and 76.
The VOFFSET_RAIL etch runs should be routed in the following order: pin 23, pin 28, pin 33, pin 38, pin 63, pin
68, pin 73, and pin 78. The etch runs should be short and direct as they must carry 35 ns current spikes of up to
0.64 amps peak. Bypass capacitors should be placed near and connected to pins 28 and 73 to provide
bypassing on both sides.
The VOFFSET filter and bypass capacitors must be placed near and connected to pin 49. VOFFSET pin 49 must
also be connected (optionally with a 0-ohm resistor) to VOFFSET_RAIL at or between pins 38 and 63.
NOTE
Aluminum electrolytic capacitors may not be suitable for the DLPA200 application. At the
switching frequencies used in the DLPA200 (up to 1.5MHz), aluminum electrolytic
capacitors drop significantly in capacitance and increase in ESR resulting in voltage
spikes on the power supply rails, which could cause the device to shut down or perform in
an unreliable manner.
20
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
DLPA200
www.ti.com
DLPS015D – APRIL 2010 – REVISED MAY 2015
11 Layout
11.1 Layout Guidelines
CAUTION
Board layout and routing guidelines must be followed explicitly and all external
components used must be in the range of values and of the quality recommended for
proper operation of the DLPA200. Important: Thermal pad(s) must be tied to
VRESET_RAIL, do not connect to ground.
CAUTION
Thermal pads must be tied to VRESET_RAIL. Do not connect to ground.
Suitable Kelvin connections should be provided for the switching regulator feedback pins: VBIAS (pin 9) and
VRESET (pin 13).
The etch traces that connect the switching devices: VBIAS_SWL (pin 8) and VRESET_SWL (pin 12) should be
as short and wide as possible to minimize leakage inductances. The etch traces that connect the switching
converter components (inductors, flywheel diodes and filtering capacitors) should also be as short and wide as
possible. The electrical loops that these components form should be as small and compact as possible, with the
ground referenced components forming a star connection.
Due to the fast switching transitions appearing on the sixteen reset OUTx pins, it is recommended to keep these
traces as short as possible. Also, to minimize potential cross-talk between outputs, it is advisable to maintain as
much clearance between each of the output traces.
11.1.1 Grounding Guidelines
The PWB should have an internal ground plane that extends under the DLPA200. All 9 ground pins (1, 7, 14, 20,
41, 46, 53, 55, and 60) must be connected to the ground plane using the shortest possible runs and vias. All filter
and bypass capacitors must be placed near the pin being filtered or bypassed for the shortest possible runs to
the part and to the ground plane.
11.2 Thermal Considerations
The DLPA200 package should be thermally bonded or soldered to an external thermal pad on the PWB surface.
The recommended dimensions of the thermal pad are 10 × 10 mm centered under the part. The metal bottom of
the package is tied internally to the substrate at the VRESET_RAIL voltage level. Therefore, the thermal pad on
the board must be isolated from any other extraneous circuit or ground and no circuit vias are allowed inside the
pad area. Thermal pads are required on both sides of the PWB and should be connected together through an
array of 5 × 5 thermal vias, 0.5 mm in diameter. Thermal pads and the thermal vias are connected to
VRESET_RAIL and isolated from ground, or any other circuit. An internal P12V or VBB plane should be
located directly underneath the top layer and have an isolated area under the DLPA200. This isolated area must
be a minimum of 20 cm2 and connect to the thermal pad of the DLPA200 through the thermal vias. The potential
of the isolated area will also be at VRESET_RAIL. The internal ground plane should extend under the DLPA200
to help carry the heat away. Please refer to the PowerPAD Thermally Enhanced Package application report
(SLMA002) for details on thermally efficient package design considerations.
Careful consideration should be taken with respect to DLPA200 placement in the vicinity of local PWB hotspots.
Heat generated from adjacent components may impact the DLPA200 thermal characteristics.
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
21
DLPA200
DLPS015D – APRIL 2010 – REVISED MAY 2015
www.ti.com
12 Device and Documentation Support
12.1 Device Support
12.1.1 Device Nomenclature
The device marking consists of the fields shown in Figure 6.
Figure 6. Device Marking (Device Top View)
DLPA200PFP is functionally equivalent to 2506593-0005N.
12.2 Documentation Support
12.2.1 Related Documentation
Table 8. Related Links
Document
TI Literature Number
DLP 0.55 XGA Chip-Set data sheet
DLPZ004
DLP5500 0.55 XGA DMD data sheet
DLPS013
DLPC200 Digital Controller data sheet
DLPS014
DLP® Discovery™ 4100 Chipset Datasheet
DLPU008
DLP7000 0.7 XGA Type-A DMD data sheet
DLPS026
DLP9500 0.95 1080p Type-A DMD data sheet
DLPS025
DLPC410 Digital Controller data sheet
DLPS024
DLPA200 DMD Micromirror Driver data sheet
DLPS015
DLPR410 EEPROM data sheet
DLPS027
12.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
22
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
DLPA200
www.ti.com
DLPS015D – APRIL 2010 – REVISED MAY 2015
12.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DLPA200
23
PACKAGE OPTION ADDENDUM
www.ti.com
15-Dec-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
DLPA200PFP
ACTIVE
Package Type Package Pins Package
Drawing
Qty
HTQFP
PFP
80
5
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR
Op Temp (°C)
Device Marking
(4/5)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
15-Dec-2014
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
Similar pages