OptoSupply OSM5XNE3E1E Xeon 3 power warm white led Datasheet

Xeon 3 Power Warm White LED
OSM5XNE3E1E
VER C.2
■Features
■Outline
●
Highest Luminous Flux
●
Super Energy Efficiency
●
Long Lifetime Operation
●
Superior ESD protection
●
Superior UV Resistance
Dimension
3.6
BackView
■Applications
Anode
●
Read lights (car, bus, aircraft)
●
Portable (flashlight, bicycle)
●
Bollards / Security / Garden
●
Traffic signaling / Beacons
●
In door / Out door Commercial lights
●
Automotive Ext
ESD Protection Diode
Unit:mm
Tolerance:±0.30mm
■Absolute Maximum Rating
Item
(Ta=25℃)
■Directivity
Symbol
Value
Unit
DC Forward Current
IF
800
mA
Pulse Forward Current*
IFP
1000
mA
Reverse Voltage
VR
5
V
Power Dissipation
PD
3200
mW
Operating Temperature
Topr
-30 ~ +85
℃
Storage Temperature
Tstg
-40~ +100
℃
Lead Soldering Temperature
Tsol
260℃/5sec
-
0
Duty ratio max 1/10
■Electrical -Optical Characteristics
Item
Symbol
DC Forward Voltage
VF
DC Reverse Current
■Forward Operating Current (DC)
(Ta=25℃)
Condition
Min.
Typ.
Max.
Unit
IF=350mA
3.0
3.3
4.0
V
IF=700mA
3.5
3.8
4.5
V
IR
VR=5V
-
-
10
µA
Luminous Flux
Φv
IF=700mA
190
210
-
lm
Color Temperature
CCT
IF=700mA
-
3000
-
K
x
IF=700mA
-
0.44
-
-
Chromaticity
Coordinates*
50% Power Angle
0
y
IF=700mA
-
0.41
-
-
2θ1/2
IF=700mA
-
140
-
deg
800
Forward Current, IF (mA)
*Pulse width Max.10ms
Cathode
700
600
500
400
300
200
100
RJ-A=30℃/W
RJ-A=25℃/W
RJ-A=20℃/W
RJ-A=15℃/W
0
0
25
50
75
100
125
Ambient Temperature, TA (℃)
Note: Don’t drive at rated current more than 5s without heat sink for Xeon 3 emitter series.
LED & Application Technologies
http://www.optosupply.com
VER C.2
Xeon 3 Power Warm White LED
OSM5XNE3E1E
VER C.2
■ Soldering Heat Reliability :
Reflow soldering Profile
· Reflow soldering should not be done more than two times.
· When soldering, do not put stress on the LEDs during heating.
· After soldering, do not warp the circuit board.
· Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable,
a double-head soldering iron should be used. It should be confirmed beforehand whether the
characteristics of the LEDs will or will not be damaged by repairing.
Solder
Average ramp-up rate = 3ºC/sec. max.
Preheat temperature: 150º~180ºC
Preheat time = 120 sec. max.
Ramp-down rate = 6ºC/sec. max.
Peak temperature = 220ºC max.
Time within 3ºC of actual
peak temperature = 25 sec. max.
Duration above 200ºC is 40 sec. max.
LED & Application Technologies
http://www.optosupply.com
VER C.2
Similar pages