DDK BNC75-PJ-1.5CCA-EXBV-CF 75 î© bnc style connector Datasheet

75 Ω BNC Style Connector
BNC75 Series
FEATURE
Frequency
Range
・ 75 Ω of BNC style connector
・ BNC style connectors can be mated.
・ Bayonet coupling mechanism for reliable
connection.
Characteristic
Impedance
75 Ω
Lock Type
Bayonet
APPLICATIONS
Measurement Equipment, Broadcasting, HDTV
SPECIFICATIONS
Characteristic Impedance
Rated Voltage
Dielectric Withstanding Voltage
75 Ω
500VAC(r.m.s.)
1500V AC(r.m.s.)for1 minute
Contact Resistance
3m Ω Max.
Operating Temperature
-55 〜 +85℃
Insulation Resistance
V.S.W.R.
1000M Ω Mim. at 500V DC
1.3 max. at DC to 1GHz
* The specifications are typical but may not apply to all connectors. Please check
the specifications on each item with its drawing from us when you use.
MATERIAL/FINISH
Item
Shell (Body)
Contact (Male)
RoHS
Compliant
Compliant
Material / Finish
Copper Alloy / Ni or Ag Plating
Copper Alloy / Ag or Au Plating
Contact (Female) Copper Alloy / Ag or Au Plating
Insulator
Gasket
PTFE
Silicon Rubber
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
170605
http://www.ddknet.co.jp
BNC75
Series
Unit:mm
○ Straight Cable Plug
L
12.7±0.05
30
φ11.7
30
φ11.7
φ11.7
A
30
+0.1
+0.1
4-φ3.1 0
φ11.5 0
φ15.5
φ15.5
2
33.2
12.7
+0.1
4-φ3.1 0
15.8
26.3
18
12.7
4-φ3.1
17.5
12.7
15.8
+0.1
φ11.5 0
+0.1
2.3 26.3 15.8
4-φ3.0 0
26.3
2.3
Part Number
2.3
12.7
12.7
12.7
39
4-φ3
Finish
Outer
12.7
17.5
12.7
+0.1
15.84-φ3.0 0±0.05
12.7
+0.1
26.3
+0.1
4-φ3.0 0
φ9.0 0
+0.1
+0.1
4-φ3.0 0
φ9.0 0
12.7±0.05
+0.1
φ9.0 0
18
33.2
4-φ3.1
12.7±0.05
15.8
BNC75-SP-1.5CCA-EXBV-CF L
18
33.2
5C-FB
Center
Ag
Ag
Ni
Ag
Ni
Ag
Center
15.8
BNC75-J-2.5C2W-CR10A-CF
26.3
12.7±0.05
Outer
Finish
12.7
12.7±0.05
2.5C-2W
17.5
Ni
+0.1
12.7±0.05
2
Center
Conductor Conductor
4-φ3.0 0
2
18
http://www.ddknet.co.jp
Assembly
Crimp Tool
Instruction
CR-H-1101
17.5
2.5C-XW
+0.1
0
3
4-φ3.1
Applicable
Cable
12.7±0.05
+0.1
φ9.0 0
Assembly
Instruction
17.5
12.7
φ9.0
◎ Please acknowledge that the specification etc. of this catalog might change
by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
33.2
Finish
4-φ3.1
Conductor Conductor
12.7
12.7±0.05 4-φ3.1 Ni
1.5CCA-EXBV
Au
17.5
2.3
2.3
18
12.7 37
5C-2V17.5
Applicable Cable
±0.05
32.5
2 32.5
φ15.5
+0.1
φ11.5 0
Part Number
φ14.5
φ4.0
φ15.5 φ11.7
φ11.7
φ15.5
2
Outer
Conductor Conductor
12.7
+0.1
12.7±0.05
φ11.5 0
32.5
○ Straight Cable
Jack
33.2
φA
+0.1
BNC75-SP-5CFB-CF
32.5
2
L
4-φ3
17.5
4-φ3.1 0
2.3
15.8
BNC75-P-5C2W-CF
5C-2W
37
12.7
+0.1
±0.05
12.7+0.1
0
4-φ3.1
L
0
φ11.5
17.5
2.3
32.5
4-φ3
12.7
12.7
30
4-φ3
17.5
12.7
φ14.5
φ14.5
φ14.5
φ14.5
φ14.5
φ4.0
φ17.5
φ4.0
φ4.0
φ4.0
A
12.7
17.5
Cable
+0.1
4-φ3.1 0
15.8
Au
12.7
A
15.8
L
Assembly
Instruction
4-φ3
12.7
Applicable
Part Number
L
Center
Ni
+0.1
4-φ3.1 0
2.3
15.8
2.3
+0.1
φA 0
BNC75-P-5-CF 2.3
CR-H-1132
12.7
A
6.5
12.7±0.05
φ17.5
A
1
Outer
12.7
φ14.5 φ14.5
φ14.5
φ14.5
φAφ17.5
φ17.5
φ14.5
φ17.5
29
Au
12.7
12.7
12.7±0.05
14.0
2.3
CR-H-1105
Conductor Conductor
3C-2V
12.7±0.05
+0.1
φA 0
1
12.7
+0.1
12.7±0.05
BNC75-SP-3C2V-CR1-DA1
φA 0
Au
Finish
φA
Cable
+0.1
+0.1
4-φ3.1 0
φA 0
φ14.5
26.3
29
17.5
4-φ3.1
Applicable
12.7
Part Number
+0.1
L 4-φ3.1 0
12.7±0.05
12.7±0.05
12.7±0.05
±0.05
12.7
+0.1
CR-H-1100
17.5
12.7
+0.1
14.00
4-φ3.1
φA 0
Ni
Assembly
Crimp Tool
Insutruction
Au
12.7
L
17.5
12.7
12.7±0.05
φ14.5
φ14.5
φ14.5
φ14.5
φA
φA
φA
φA
29
30
7.90
+0.1
2.3
Ni
17.5
12.7
L
2.3
14.0
0
4-φ3.1
3C-2WS
29
29
6.25
12.7
14.0
3C-2W
BNC75-P-3CW-CR10B-CF
Ni
4-φ3.1
2.5C-XW
2.3
14.0
BNC75-P-2.5CW-CR10B-CF
2.5C-2W
26.3
φA
1.5C-QEW
12.7±0.05
12.7±0.05
12.7±0.05
12.7±0.05
26.3
4-φ3.1
5.50
12.7±0.05
φ14.5
φA
26.3
Center
4-φ3.1
Conductor Conductor
1.5C-2W
L
2.3
Outer
12.7±0.05
12.7±0.05
12.7±0.05
12.7±0.05
φ14.5
φ14.5
φ14.5
φA
φA
φA
26.3
φA
Cable
BNC75-P-1.5CQEW-CF
Finish
4-φ3.1
Applicable
Part Number
Au
Assembly
Instruction
Crimp Tool
CR-H-1105
30
φ11.7
12.7
4-φ3.1
BNC75
Series
○ Straight
Bulkhead Cable Jack
32.5
2.3
15.8
12.7
26.3
17.5
+0.1
4-φ3.0 0
φ15.5
Cable
+0.1
φ9.0 0
2.5C-2W
BNC75-BJ-2.5C2W-CR1-CF
2
Outer
Finish
Center
Conductor Conductor
Ni
±0.05
12.7
2.5C-QEW
18
33.2
12.7±0.05
Applicable
Part Number
Assembly
Crimp Tool
Instruction
Au
○ Straight Panel Cable Jack
Cable
φ11.7
12.7
1.5C-2V
1.5C-QEV
Conductor Conductor
CR-H-1101
33.00
4-φ3.1
Ni
Au
CR-H-1101
34.5
Ni
Ag
CR-H-1100
17.5
+0.1
+0.1
15.8φ11.5 0
12.7
17.5
+0.1
4-φ3.1 0
4-φ3
12.7±0.05
17.5
12.7±0.05
12.7
12.7
+0.1
φ11.5 0
12.7
4-φ3.1
12.7±0.05
2.3
15.8
12.7
4-φ3.1
Panel Mounting
Dimensions
26.3
+0.1
0
4-φ3.1
12.7±0.05
32.5
17.5
2.3
15.8
26.3 2
18
12.7
12.7±0.05
12.7±0.05
12.7
4-φ3.1
17.5
2.3
3
15.8
26.3
+0.1
φ9.0 0
12.7
17.5
+0.1
4-φ3.0 0
12.7±0.05
12.7±0.05
32.5
12.7
φ15.5
φ11.7
φ14.5
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without
notice.
+0.1
4-φ3.1
4-φ3.0 0
Moreover, the characteristic and the specification of the published product are the reference values.
+0.1
Please confirm the
content
with the latest delivery specifications when you use the product.
φ11.5 0
http://www.ddknet.co.jp
Assembly
Crimp Tool
Instruction
Au
L
17.5
Center
Ni4-φ3
2.5C-2V
2.3
CR-H-16776
12.7
15.8
1.5CCA-EXBV
34.5
L
+0.1
4-φ3.1 0
15.80
φ11.5
L
30
2.3
Outer
12.7
φ4.0
Cable
BNC75-PJ-2.5V-CR-Ni-CF
CR-H-1132
4-φ3
Finish
L
12.7±0.05
4-φ3
12.7
L
+0.1
2.3
Applicable
BNC75-PJ-1.5CV-CR2-CF
φ14.5
15.8
30
+0.1
Part Number
4
12.7±0.05
Panel Mounting Dimensions
12.7±0.05
φ4.0
2.3
A
Au
Ni
17.5
Crimp
Tool
17.5
+0.1
BNC75-PJ-1.5CCA-EXBV-CF
φ14.512.7±0.05
φ17.5
12.7±0.05
φ14.5
φ14.5
+0.1
φA 0
17.5
12.7
12.7
+0.1
0
4-φ3.1
12.7±0.05
A
φ14.5
12.7
φ14.5
φ17.5
14.0
Au
Assembly
Instruction
12.7
φA 0
φ14.5
φ14.5
12.7±0.05
φA
φ14.5
+0.1
14.0+0.1
φA 0
4-φ3.1 0
12.7
+0.1
φA 0
L
29
L
17.5
29
4-φ3.1 0
2.3
2.3
Ni
12.7±0.05
φ14.5
φA
φ14.5
L
11.3 30.0
+0.1
4-φ3.1
12.7
14.0
14.0 4-φ3.1
L
4-φ3.1 0
12.7
φ14.5
φA
φ14.5
2.3
φ14.5
4-φ3.1
26.3
11.8 32.6
2.3
3C-2V
Center
Conductor Conductor
3C-2WS
BNC75-PJ-3C2V-CR1-CF
Outer
12.7±0.05
26.3
Finish
L
12.7
BNC75-PJ-3CW-CR10B-CF
φA
12.7
Applicable
Part Number
12.7±0.05
φA
φ14.5
4-φ3.1
A
Series
L
○ Receptacle Jack
+0.1
30
17.5
Part Number
2.3
12.7±0.05
15.8
BNC75-R-A-CF
26.3
4-φ3.1
15.8
26.3
2
33.2
17.5
+0.1
+0.1
φ9.0 0
12.7
18
12.7
4-φ3.0 0
12.7
φ15.5
2.3
12.7±0.05
4-φ3.1
12.7±0.05
32.5
Unit:mm
12.7±0.05
12.7±0.05
φ11.5 0
φ11.7
12.7
4-φ3.1 0
+0.1
12.7±0.05
17.5
+0.1
Panel Mounting Dimensions
4-φ3.0 0
12.7±0.05
φ14.5
+0.1
φ11.5 0
+0.1
φ9.0 0
12.7
BNC75
15.8
2.3
φ14.5
φ4.0
φ14.5
12.7
4-φ3.1
12.7±0.05
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
4
Outer
Finish
Conductor
Ni
Center
Conductor
Au
BNC75
Series
○ Assembly Instruction(1)
Parts Configulration
Heat-shrinkable
tubetube Ferule
Heat-shrinkable
Ferule
①
Sleeve
Insulator
CableCable
15
Contact
Sheath
Heat-shrinkable
tube tube Sheath
Heat-shrinkable
15
Sleeve
Sleeve
Body
Body
① Insert the heat-shrinkable tube into the cable
15
OuterOuter
Conductor
Conductor
Body
Insulator
Insulator
Ferule
Ferule
②
Contact
Insulator
Insulator Contact
and cut the cable as fig.1. Please be carefule to
not damage the outer conductor.
② Insert the ferule from the end of outer
conductor to the sheath.
Spread the top of outer conductor and insert the
Outer Conductor
sleeve between insulator and outer conductor.
Sleeve
Sleeve
To push the sleeve into the cable, please refer to
the tool as fig.2. And cut the outer conductor
Inserting
Too for
Inserting
TooSleeve
for Sleeve
Insulator
along the sleeve.
20 min.
20 min.
PushPush
into sleeve
into sleeve
on this
on side
this side
7.2 7.2
3.5 3.5
Sleeve
③
③ Cut the insulator and center conductor as fig.3.
Insulator
Insulator
Cut the center conductor after pre-soldering.
Inserting Too for Sleeve
Center
Conductor
Center
Conductor
Insulator
Insulator (Pre-soldering)
(Pre-soldering)
3.5
Insulator
Soldering
Soldering
④
Center Conductor
(Pre-soldering)
Insulator
Insulator
Shave the extra solder from the contact along the
Contact
Contact
round of contact.
No gap
No gap
ring
Contact
④ Insert the insulator and solder the center
conductor and contact. Pre-solder the contact.
⑤
⑤ Inser above cable into the body . And insert the
contact.
gap
⑥ Crimping position is as fig.6.
⑥
Part Number
BNC75-P-2.5CW-CR10B-CF
BNC75-P-3CW-CR10B-CF
Heat-shrinkable
tube tube
Heat-shrinkable
Crimp Tool
CR-H-1105
CR-H-1132
⑦
⑦ Cover the heat-shrinkable tube on the root of
the connector body and heat up the tube.
Heat-shrinkable tube
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
5
BNC75
Series
Unit:mm
○ Assembly Instruction(2)
Parts Configulration
Boot
Ferule
Sleeve
Contact
Boot
Ferule
Sleeve
Contact
Body
Body
The cable length require for the double-ended cable
assembly.
L
L-12mm
L
①
Cable
15
Cable
15
① Insert the boot into the cable and cut the cable
Hole the outer
as fig.1. Please be carefule to Crimping
not damage
Boot
Sheath
Outer Conductor
Boot
Sheath
Outer Conductor
conductor.
Crimp Tool
Crimp Tool
Insulator
Ferule
②
Insulator
Ferule
Insulator
Sleeve
Insulator
Sleeve
Crimping Hole
Center Conductor
Center Conductor
4.8 3.4
② Insert the ferule toward
outer conductor.
4.8 3.4
Spread the outer conductor
and press in the
Contact
sleeve with stripper (P/N:89134).
Contact
Pull out the edge
Crimp Tool
Pull out the edge
Crimp Tool
Crimped
Crimped
Stripper
(P/N:89134)
Stripper
(P/N:89134)
③
Center Conductor
Center Conductor
Cut the insulator and center conductor
along this side
Cut the insulator and center conductor
along this side
Body
Push
crimp
tool
into outer conductor and insulator
③the
Cut
the
extra
Body
the root of body.
Push the
crimpthe
tool stripper
into
from
along the surface as fig.3.
the root of body.
Crimp Position
Crimp Position
④ Push the edge of the stripper and rotate.
Separate the insulator toward the arrow.
④
Cut the outer conductor along the surface of sleeve.
Boot
Boot
Cut off the outer conductor
Cut off the outer conductor
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
6
Ferule
ator
Contact
Sleeve
Body
BNC75
Series
○ Assembly Instruction(2)
15
⑤
Crimping Hole
Outer Conductor
⑤ Pinch the contact in the crimping hole(center
hole) and insert the center conductor of the cable.
Crimp the contact (match the side hole of contact
Crimp Tool
with the curve of crimping hole of tool.)
Insulator
Ferule
4.8
Sleeve
Center Conductor
3.4
Contact
Crimp Tool
Crimped
pper
(P/N:89134)
⑥
Center Conductor
Push the crimp tool into
the root of body.
⑥ Insert the above contact into the body until
the top of the contact is same level of the top
of insulator.
Please do not rotate the body and cable
before crimping.
Body
Crimp the root of the body as fig.6.
r
Crimp Position
⑦
⑦ Cover the boot on the body.
Boot
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
7
BNC75
Series
Unit:mm
○ Assembly Instruction(3)
Parts Configulration
Nut
Washer
Gasket
Clamp
Male Contact
Plug Shell
15
Nut
①
Washer
Gasket
Clamp
Male Contact
Plug Shell
① Cut the cable as fig.1
15
Please be carefule to not damage the outer
conductor.
② Insert the nut, washer, gasket and clamp as
②
fig.2. The clamp is holded on the sheath and pick
the outer conductor.
3
③
6
③ Cut the insulator and center conductor.
Turn down the outer conductor to the clamp and cut
the outer conductor along the clamp. Cut the
3
insulator and center conductor as fig.3.
6
Please be careful to not damage the center
conductor.
④
④ Solder up the contact to the center conductor.
Please be careful to not be swelled up the solder.
Please be careful to not gap between contact and
insulator.
Please be careful to not deform the insulator by
soldering.
⑤ Inser the above contact into the body and
screw up the nut.
⑤
Please screw up the nut by wrench.
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
8
BNC75
Series
○ Assembly Instruction(4)
Parts Configulration
Heat-shrinkable tube
Ferule
Heat-shrinkable tube
Sleeve
Ferule
Insulator
Sleeve
Insulator
Contact
Body
Contact
Body
20
①
20
Outer Conductor
Sheath
Heat-shrinkable tube
① Insert the heat-shrinkable tube into the cable
and cut the cable as fig.1.
Outer Conductor
Sheath
Heat-shrinkable tube
Cut off extra outer conductor
②
Cut off extra outer conductor
3.5
A
A
② Insert the ferule on the outer conductor.
3.5
Center Conductor
Insulator
Center Conductor
Ferule
SleeveInsulator
Ferule
Sleeve
③
Insulator
Insulator
Pick the outer conductor and spread the top of center
conductor. Insert the insulator from the outer conductor.
Cut the extra outer conductor along the sleeve.
Cut the insulator in length A. Cut the center conductor
after pre-soldering.
Part Number
Soldering
A
BNC75-J-2.5C2W-CR10A-CF
7.2mm
BNC75-PJ-3CW-CR10B-CF
6.8mm
③ Insert the insulator and solder the contact.
Soldering
Contact
④
Contact
Crimp Tool
Crimp Tool
④ Insert the above contact into the body and crimp
the body as fig.4.
Part Number
Same level
Same level
Body
Crimp Tool
BNC75-J-2.5C2W-CR10A-CF
CR-H-1105
BNC75-PJ-3CW-CR10B-CF
CR-H-1132
Body
⑤
⑤ Cover the heat-shrinkable tube on the root of
the connector body and heat up the tube.
Heat-shrinkable tube
Heat-shrinkable tube
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
9
Similar pages