IDPC-65
65W Constant Current Mode LED Driver
series
SELV
(for DA-Type only)
■ Features
Constant Current mode output
Flicker free design
PCB type design
Built-in active PFC function
No load power consumption<0.5W(Blank-Type),
■ Applications
LED panel lighting
LED flood lighting
Indoor LED lighting
Standby power consumption<0.5W(DA-Type)
Function options: 2 in 1 dimming (dim-to-off);
Auxiliary DC output; DALI
3 years warranty
■ Description
IDPC-65 series is a 65W PCB type LED AC/DC driver featuring the constant current mode output
with flicker free design. IDPC-65 operates from 180~295VAC and offers models with different rated
current ranging between 700mA and 1750mA. Thanks to the efficiency up to 89%, with the fanless
design, the entire series is able to operate for -20℃~+40℃ ambient temperature under free air convection.
IDPC-65 is equipped with various function options, such as dimming methodologies, so as to provide
the optimal design flexibility for lighting system.
■ Model Encoding
IDPC - 65 A - 1400
Function options
Rated output current(700/1050/1400/1750mA)
A:Auxiliary DC output(12V@50mA)
:None
Rated wattage
Series name
{
Type
Blank
DA
Function
2 in 1 dimming (0~10VDC and 10V PWM)
DALI control technology
Note
In Stock
In Stock
Note: The DALI control model(DA Type) only for IDPC-65 Non Auxiliary DC output models.
File Name:IDPC-65-SPEC 2017-05-03
IDPC-65
65W Constant Current Mode LED Driver
series
SPECIFICATION
IDPC-65 -700
IDPC-65 -1050
IDPC-65 -1400
IDPC-65 -1750
RATED CURRENT
700mA
1050mA
1400mA
1750mA
RATED POWER
65.1W
65.1W
64.4W
63W
CONSTANT CURRENT REGION Note.2 69 ~ 93V
46 ~ 62V
34 ~ 46V
27 ~ 36V
OPEN CIRCUIT VOLTAGE(max.) 118V
82V
60V
53V
MODEL
OUTPUT
CURRENT RIPPLE
5% max. @rated current
CURRENT TOLERANCE
±7.0%
SETUP TIME
500ms / 230VAC
Note.4
AUXILIARY DC OUTPUT Note.5 Nominal 12V(deviation 11.4~12.6)@50mA for IDPC-65A only
VOLTAGE RANGE
Note.3
FREQUENCY RANGE
INPUT
180 ~ 295VAC
254 ~ 417VDC
(Please refer to "STATIC CHARACTERISTIC" section)
47 ~ 63Hz
POWER FACTOR (Typ.)
PF>0.95/230VAC, PF>0.9/277VAC@full load
(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
TOTAL HARMONIC DISTORTION
THD< 20%@load≧75%/230VAC, 277VAC
(Please refer to “TOTAL HARMONIC DISTORTION” section)
EFFICIENCY (Typ.)
89%
AC CURRENT
0.4A/230VAC
INRUSH CURRENT (Typ.)
COLD START 30A(twidth=100μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
87%
86%
86%
0.3A/277VAC
MAX. No. of PSUs on 16A
32 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC
CIRCUIT BREAKER
LEAKAGE CURRENT
<0.75mA / 277VAC
NO LOAD / STANDBY
POWER CONSUMPTION
No load power consumption <0.5W for Blank-Type, <1.2W for IDPC-65A
Standby power consumption <0.5W for DA-Type
PROTECTION SHORT CIRCUIT
Hiccup mode,auto-recovery after fault condition is removed for DA type；
Hiccup mode,re-power on to recovery for other type
WORKING TEMP.
Ta= -20 ~ +40℃ (ambient temperature)
WORKING HUMIDITY
20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT
±0.03%/℃ (0 ~ 40℃)
VIBRATION
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY STANDARDS
UL8750, CSA C22.2 NO.250.13-12; ENEC EN61347-1, EN61347-2-13, EN62384,
GB19510.1,GB19510.14 approved
DALI STANDARDS Note.7 Compliance to IEC62386-101,102 for DA-Type only
SAFETY &
WITHSTAND VOLTAGE
I/P-O/P:3.75KVAC
EMC
ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION
Compliance to EN55015, EN61000-3-2 Class C (≧75% load) ; EN61000-3-3,GB17743,GB17625.1
EMC IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level( surge immunity:Line-Line:1KV )
MTBF
380.7Khrs min.
OTHERS DIMENSION
PACKING
NOTE
MIL-HDBK-217F (25℃)
130*67.5*20.5mm(L*W*H)
0.15Kg; 81pcs/ 13Kg/ 1.46CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
2. Please refer to "DRIVING METHODS OF LED MODULE".
3. De-rating may be needed under low input voltages. Please refer to STATIC CHARACTERISTIC sections for details.
4. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time or set up failure.
5. There is no design of short circuit protection for the Auxiliary DC output; this function can not be used when dimming input terminals(DIM+,DIM-)
are short circuit or when it is no load or short circuit at output(Vo+,Vo-).
6. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be
affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
7.The DALI version driver does not support the bit 1: Lamp failure in the Command 144 Query status of the DALI standard.
File Name:IDPC-65-SPEC 2017-05-03
IDPC-65
65W Constant Current Mode LED Driver
series
BLOCK DIAGRAM
fosc : 70KHz
AUX+(for IDPC-65A )
AUX- (for IDPC-65A )
RECTIFIERS
I/P
EMI FILTER
&
RECTIFIERS
RECTIFIERS
&
FILTER
POWER
SWITCHING
O.L.P.
PWM&PFC
CONTROL
CURRENT
LIMIT
Vo+
VoDIM+(DA+)
DIM-(DA-)
DETECTION
CIRCUIT
DRIVING METHODS OF LED MODULE
※ This series works in constant current mode to directly drive the LEDs.
In the constant current region, the highest voltage at the output of the driver
depends on the configuration of the end systems.
100
Vo(%)
Constant
Current area
Should there be any compatibility issues, please contact MEAN WELL.
75
(min.)
Hiccup
Protection
50
100
Io(%)
Typical output current normalized by rated current (%)
File Name:IDPC-65-SPEC 2017-05-03
IDPC-65
65W Constant Current Mode LED Driver
series
ACL
ACL
ACN
ACN
TB1
FS1
-
DIMMING OPERATION
P
P
+
S
DIM+(DA+)
DIM-(DA-)
Vo+
Vo-
HS2
HS1
TB2
S
※ 2 in 1 dimming function
Output constant current level can be adjusted by applying one of the two methodologies between DIM+ and DIM-:
0 ~ 10VDC, or 10V PWM signal.
Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers.
◎ Applying additive 0 ~ 10VDC
100%
90%
Vo-
+
+
-
-
DIM+
+
Output current (%)
80%
Vo+
70%
60%
50%
40%
30%
Additive Voltage
-
20%
DIM-
10%
“DO NOT connect "DIM- to Vo- ”
0%
0V 1V
2V 3V 4V 5V 6V 7V 8V 9V 10V
Dimming input: Additive voltage
◎ Applying additive 10V PWM signal (frequency range 300Hz ~ 3KHz):
100%
90%
Vo-
+
+
-
-
DIM+
Additive PWM signal
Output current (%)
80%
Vo+
70%
60%
50%
40%
30%
20%
DIM“DO NOT connect "DIM- to Vo- ”
10%
0%
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
Duty cycle of additive 10V PWM signal dimming input
Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< I out<8%.
2. The output current could drop down to 0% when dimming input is about 0Vdc or 10V PWM signal with 0% duty cycle.
※ DALI Interface (primary side; for DA-Type)
Apply DALI signal between DA+ and DA-.
DALI protocol comprises 16 groups and 64 addresses.
First step is fixed at 8% of output.
File Name:IDPC-65-SPEC 2017-05-03
1
0.95
0.9
0.85
277V
0.8
230V
0.75
0.7
50%
60%
70%
INPUT VOLTAGE (V)
80%
90%
100%
LOAD
91
18
88
16
14
85
12
10
277VAC
8
230VAC
6
82
277V
79
230V
76
4
73
2
0
50%
60%
70%
80%
90%
100%
70
10%
20%
30%
40%
50%
60%
70%
80%
90% 100%
File Name:IDPC-65-SPEC 2017-05-03
IDPC-65
65W Constant Current Mode LED Driver
series
MECHANICAL SPECIFICATION
Unit:mm
130
122
-
4 *ψ
FS1
1
2
3
+
S
59.5
TB1
67.5
P
P
4
3. 5
S
1
2
3
4
5
6
20.5
HS2
HS1
TB2
Terminal Pin No. Assignment(TB1)
Pin No.
1
2
3
4
Assignment
ACL
ACL
ACN
ACN
IDPC-65
Terminal Pin No. Assignment(TB2)
Pin No.
1
2
3
4
Assignment
DIM+ (DA+)
DIM- (DA-)
Vo+
Vo-
IDPC-65A
Terminal Pin No. Assignment(TB2)
Pin No.
1
2
3
Assignment
DIM+
DIMVo+
Pin No.
4
5
6
Assignment
VoAUX+
AUX-
INSTALLATION MANUAL
Please refer to :http://www.meanwell.com/manual.html
File Name:IDPC-65-SPEC 2017-05-03