TI1 ADS7854IPW Simultaneous-sampling, analog-to-digital converter Datasheet

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
Reference
Design
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
ADSxx54 Dual, High-Speed, 16-, 14-, and 12-Bit,
Simultaneous-Sampling, Analog-to-Digital Converters
1 Features
2 Applications
•
•
•
•
•
1
•
•
•
•
•
16-, 14-, and 12-Bit, Pin-Compatible Family
Simultaneous Sampling of Two Channels
Supports Fully-Differential Inputs
High Speed:
– ADS8354: 16 Bits, 700 kSPS
– ADS7854: 14 Bits, 1 MSPS
– ADS7254: 12 Bits, 1 MSPS
Excellent DC Performance:
– ADS8354:
– 16-Bit NMC DNL, ±2.5-LSB Max INL
– ADS7854:
– 14-Bit NMC DNL, ±1.5-LSB Max INL
– ADS7254:
– 12-Bit NMC DNL, ±1-LSB Max INL
Excellent AC Performance:
– ADS8354:
– 93-dB SNR, –100-dB THD
– ADS7854:
– 88-dB SNR, –95-dB THD
– ADS7254:
– 72-dB SNR, –90-dB THD
Dual, Programmable, and Buffered
2.5-V Internal Reference
Fully-Specified Over the Extended Industrial
Temperature Range: –40°C to 125°C
Small Footprint:
WQFN-16 (3-mm × 3-mm) and TSSOP-16
•
•
•
•
•
Motor Control:
Position Measurement Using Encoders
Optical Networking: EDFA Gain Control Loops
Protection Relays
Power Quality Measurement
Three-Phase Power Controls
Programmable Logic Controllers
3 Description
The ADS8354, ADS7854, and ADS7254 belong to a
family
of
pin-compatible,
dual,
high-speed,
simultaneous-sampling, analog-to-digital converters
(ADCs) that support fully-differential analog inputs.
Each device includes two individually programmable
reference sources that can be used for system-level
gain calibration. Also, a flexible serial interface that
can operate over a wide power-supply range enables
easy communication with a large variety of host
controllers. Power consumption for a given
throughput can be optimized by using the two lowpower modes supported by the device. All devices
are fully specified over the extended industrial
temperature range (–40°C to 125°C) and are
available in pin-compatible, WQFN-16 (3-mm ×
3-mm) and TSSOP-16 packages.
Device Information(1)
PART NUMBER
ADSxx54
PACKAGE
BODY SIZE (NOM)
TSSOP (16)
5.00 mm × 4.40 mm
WQFN (16)
3.00 mm × 3.00 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Typical Application Diagram
1K 1K AVDD
AVDD
VIN+
VREF
VCM
+
+
THS4521
+
-
10
4.7 nF
AVDD
V
AINP
+
ADSxx54
AINM
10
GND
+
VIN-
1K 1K INPUT DRIVER
ADS8354 : 16-bit, 700 kSPS
ADS7854 : 14-bit, 1 MSPS
ADS7254 : 12-bit, 1 MSPS
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Device Comparison Table.....................................
Pin Configurations and Functions .......................
Specifications.........................................................
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
7.11
7.12
7.13
7.14
1
1
1
2
3
4
5
Absolute Maximum Ratings ..................................... 5
Handling Ratings....................................................... 5
Recommended Operating Conditions....................... 5
Thermal Information .................................................. 5
Electrical Characteristics: ADS8354 ......................... 6
Electrical Characteristics: ADS7854 ......................... 7
Electrical Characteristics: ADS7254 ......................... 8
Electrical Characteristics: All Devices....................... 9
Timing Requirements: Interface Mode.................... 11
Timing Characteristics: Serial Interface ................ 11
Typical Characteristics: ADS8354 ........................ 13
Typical Characteristics: ADS7854 ........................ 17
Typical Characteristics: ADS7254 ........................ 22
Typical Characteristics: Common to ADS8354,
ADS7854, and ADS7254 ......................................... 27
8
Detailed Description ............................................ 28
8.1
8.2
8.3
8.4
8.5
9
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
Register Maps and Serial Interface.........................
28
28
29
33
33
Application and Implementation ........................ 47
9.1 Application Information............................................ 47
9.2 Typical Applications ................................................ 49
10 Power-Supply Recommendations ..................... 57
11 Layout................................................................... 58
11.1 Layout Guidelines ................................................. 58
11.2 Layout Example .................................................... 58
12 Device and Documentation Support ................. 59
12.1
12.2
12.3
12.4
12.5
Related Links ........................................................
Related Documentation.........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
59
59
59
59
59
13 Mechanical, Packaging, and Orderable
Information ........................................................... 59
4 Revision History
Changes from Revision A (July 2014) to Revision B
Page
•
Made changes to the ADS8354 preview device and moved to Production Data status ........................................................ 1
•
Changed document status from Mixed Status to Production Data ........................................................................................ 1
•
Corrected cross-reference for Figure 98 .............................................................................................................................. 46
Changes from Original (October 2013) to Revision A
•
2
Page
Made changes to product preview data sheet........................................................................................................................ 1
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
5 Device Comparison Table
PRODUCT
RESOLUTION
(Bits)
INPUT CONFIGURATION
NMC (Bits)
INL (LSB)
SNR (dB)
ADS8354
16
Fully-differential
16
±2.5
93 (typ)
ADS7854
14
Fully-differential
14
±1.5
88 (typ)
ADS7254
12
Fully-differential
12
±1
74 (typ)
ADS8353
16
Single-ended and
pseudo-differential
16
±2.5
89 (typ)
ADS7853
14
Single-ended and
pseudo-differential
14
±2
84 (typ)
ADS7253
12
Single-ended and
pseudo-differential
12
±1
73.5 (typ)
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
3
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
6 Pin Configurations and Functions
RTE Package
WQFN-16
(Top View)
AINM_A
AINP_A
AVDD
GND
16
15
14
13
PW Package
TSSOP-16
(Top View)
REFIO_A
1
12
SDO_B
REFGND_A
2
11
SDO_A
REFGND_B
3
10
SCLK
REFIO_B
4
9
CS
AINP_A
1
16
AVDD
AINM_A
2
15
GND
REFIO_A
3
14
SDO_B
REFGND_A
4
13
SDO_A
REFGND_B
5
12
SCLK
REFIO_B
6
11
CS
AINM_B
7
10
SDI
AINP_B
8
9
DVDD
8
SDI
7
DVDD
6
AINP_B
AINM_B
5
Thermal Pad
Pin Functions
PIN
NO.
NAME
TSSOP
WQFN
I/O
AINM_A
2
16
Analog input
Negative analog input, channel A
AINM_B
7
5
Analog input
Negative analog input, channel B
AINP_A
1
15
Analog input
Positive analog input, channel A
Positive analog input, channel B
AINP_B
8
6
Analog input
AVDD
16
14
Supply
CS
11
9
Digital input
DESCRIPTION
Supply voltage for ADC operation
Chip-select signal; active low
DVDD
9
7
Digital I/O supply
GND
15
13
Supply
Digital ground
REFGND_A
4
2
Supply
Reference ground potential A
REFGND_B
5
3
Supply
Reference ground potential B
REFIO_A
3
1
Analog input/output
Reference voltage input/output, channel A
REFIO_B
6
4
Analog input/output
Reference voltage input/output, channel B
SCLK
12
10
Digital input
Clock for serial communication
SDI
10
8
Digital input
Data input for serial communication
SDO_A
13
11
Digital output
Data output for serial communication, channel A and channel B
SDO_B
14
12
Digital output
Data output for serial communication, channel B
Thermal pad
—
Thermal
pad
Supply
4
Submit Documentation Feedback
Digital I/O supply
Exposed thermal pad (only for WQFN). TI recommends
connecting this pin to the printed circuit board (PCB) ground.
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
7 Specifications
7.1 Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
UNIT
–0.3
6
V
REFGND_x – 0.3
AVDD + 0.3
V
GND – 0.3
DVDD + 0.3
V
AVDD to REFGND_x or DVDD to GND
Analog (AINP_x and AINM_x) and reference input (REFIO_x) voltage with
respect to REFGND_x
Digital input voltage with respect to GND
Ground voltage difference |REFGND_x-GND|
0.3
V
Input current to any pin except supply pins
±10
mA
Maximum virtual junction temperature, TJ
150
°C
(1)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
7.2 Handling Ratings
MIN
MAX
UNIT
–65
150
°C
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all
pins (1)
–2000
2000
Charged device model (CDM), per JEDEC specification
JESD22-C101, all pins (2)
–500
500
Tstg
Storage temperature range
V(ESD)
Electrostatic discharge
(1)
(2)
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
AVDD
Analog supply voltage
DVDD
Digital supply voltage
NOM
MAX
UNIT
5
V
3.3
V
7.4 Thermal Information
ADS8354, ADS7854, ADS7254
THERMAL METRIC (1)
RTE (WQFN)
PW (TSSOP)
16 PINS
16 PINS
RθJA
Junction-to-ambient thermal resistance
33.3
86.9
RθJC(top)
Junction-to-case (top) thermal resistance
29.5
21
RθJB
Junction-to-board thermal resistance
7.3
39.1
ψJT
Junction-to-top characterization parameter
0.2
0.8
ψJB
Junction-to-board characterization parameter
7.4
38.4
RθJC(bot)
Junction-to-case (bottom) thermal resistance
0.9
N/A
(1)
UNIT
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
5
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
7.5 Electrical Characteristics: ADS8354
All minimum and maximum specifications are at TA = –40°C to 125°C, AVDD = 5 V, DVDD = 3.3 V, VREF_A = VREF_B = VREF =
2.5 V (internal), and fDATA = 700 kSPS, unless otherwise noted.
Typical values are at TA = 25°C, AVDD = 5 V, and DVDD = 3.3 V.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
RESOLUTION
Resolution
DC ACCURACY
16
Bits
(1)
NMC
No missing codes
32-clock mode
16
INL
Integral nonlinearity
32-clock mode
–2.5
±1
2.5
LSB
DNL
Differential nonlinearity
32-clock mode
–0.99
±0.7
2
LSB
EIO
Input offset error
–1
±0.5
1
mV
–1
±0.5
1
EIO match
ADC_A to ADC_B
Bits
mV
μV/°C
dEIO/dT
Input offset thermal drift
±1
EG
Gain error
Referenced to the voltage at REFIO_x
–0.1
±0.05
0.1
EG match
ADC_A to ADC_B
–0.1
±0.05
0.1
dEG/dT
Gain error thermal drift
Referenced to the voltage at REFIO_x
±1
ppm/°C
CMRR
Common-mode rejection ratio
Both ADCs, dc to 20 kHz
70
dB
VREF = 2.5 V,
±VREF input range, 32-clock mode
88.6
dB
VREF = 2.5 V,
±2 × VREF input range, 32-clock mode
88.4
dB
VREF = 5 V (external),
±VREF input range, 32-clock mode
92.2
dB
VREF = 2.5 V,
±VREF input range, 32-clock mode
89
dB
VREF = 2.5 V,
±2 × VREF input range, 32-clock mode
89
dB
VREF = 5 V (external),
±VREF input range, 32-clock mode
93
dB
VREF = 2.5 V,
±VREF input range, 32-clock mode
–99
dB
VREF = 2.5 V,
±2 × VREF input range, 32-clock mode
–97.5
dB
VREF = 5 V (external),
±VREF input range, 32-clock mode
–100
dB
VREF = 2.5 V,
±VREF input range, 32-clock mode
100
dB
99
dB
100
dB
–110
dB
%FS
%FS
AC ACCURACY (2)
SINAD
SNR
THD
SFDR
Signal-to-noise + distortion
Signal-to-noise ratio
Total harmonic distortion
Spurious-free dynamic range
VREF = 2.5 V,
±2 × VREF input range, 32-clock mode
VREF = 5 V (external),
±VREF input range, 32-clock mode
ISOXT
(1)
(2)
6
ADC-to-ADC isolation
fIN = 15 kHz at 10 %FS,
fNOISE = 25 kHz at FS
LSB = least significant bit.
All ac parameters are tested at –0.5 dBFS and a 20-kHz input frequency.
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
7.6 Electrical Characteristics: ADS7854
All minimum and maximum specifications are at TA = –40°C to 125°C, AVDD = 5 V, DVDD = 3.3 V, VREF_A = VREF_B = VREF =
2.5 V (internal), and fDATA = 1 MSPS, unless otherwise noted.
Typical values are at TA = 25°C, AVDD = 5 V, and DVDD = 3.3 V.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
RESOLUTION
Resolution
DC ACCURACY
14
Bits
32-clock mode
14
Bits
16-clock mode
13
Bits
32-clock mode
–1.5
±0.5
1.5
LSB
16-clock mode
–2
±0.8
2
LSB
32-clock mode
–0.99
±0.4
1
LSB
16-clock mode
–1
±0.7
2
LSB
–1
±0.5
1
mV
–1
±0.5
1
(1)
NMC
No missing codes
INL
Integral nonlinearity
DNL
Differential nonlinearity
EIO
Input offset error
EIO match
ADC_A to ADC_B
mV
μV/°C
dEIO/dT
Input offset thermal drift
±1
EG
Gain error
Referenced to the voltage at REFIO_x
–0.1
±0.05
0.1
EG match
ADC_A to ADC_B
–0.1
±0.05
0.1
dEG/dT
Gain error thermal drift
Referenced to the voltage at REFIO_x
±1
ppm/°C
CMRR
Common-mode rejection ratio
Both ADCs, dc to 20 kHz
70
dB
%FS
%FS
AC ACCURACY (2)
83.7
dB
16-clock mode
82.9
dB
32-clock mode
VREF = 2.5 V,
±2 × VREF input range 16-clock mode
83.7
dB
82.9
dB
VREF = 5 V (external), 32-clock mode
±VREF input range
16-clock mode
84.6
dB
84.1
dB
84
dB
16-clock mode
83.5
dB
32-clock mode
VREF = 2.5 V,
±2 × VREF input range 16-clock mode
84
dB
83.5
dB
VREF = 2.5 V,
±VREF input range
SINAD
Signal-to-noise + distortion
VREF = 2.5 V,
±VREF input range
SNR
Signal-to-noise ratio
Total harmonic distortion
ISOXT
(1)
(2)
Spurious-free dynamic range
dB
84.5
dB
32-clock mode
–95
dB
16-clock mode
–92
dB
32-clock mode
VREF = 2.5 V,
±2 × VREF input range 16-clock mode
–95
dB
–92
dB
VREF = 5 V (external), 32-clock mode
±VREF input range
16-clock mode
–98
dB
–93
dB
32-clock mode
97.5
dB
16-clock mode
95
dB
32-clock mode
VREF = 2.5 V,
±2 × VREF input range 16-clock mode
97.5
dB
95
dB
VREF = 5 V (external), 32-clock mode
±VREF input range
16-clock mode
99
dB
95
dB
–90
dB
fIN = 15 kHz at 10 %FS,
fNOISE = 25 kHz at FS
ADC-to-ADC isolation
82
85
VREF = 2.5 V,
±VREF input range
SFDR
32-clock mode
81.8
VREF = 5 V (external), 32-clock mode
±VREF input range
16-clock mode
VREF = 2.5 V,
±VREF input range
THD
32-clock mode
LSB = least significant bit.
All ac parameters are tested at –0.5 dBFS and a 20-kHz input frequency.
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
7
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
7.7 Electrical Characteristics: ADS7254
All minimum and maximum specifications are at TA = –40°C to 125°C, AVDD = 5 V, DVDD = 3.3 V, VREF_A = VREF_B = VREF =
2.5 V (internal), and fDATA = 1 MSPS, unless otherwise noted.
Typical values are at TA = 25°C, AVDD = 5 V, and DVDD = 3.3 V.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
RESOLUTION
Resolution
DC ACCURACY
12
Bits
(1)
NMC
No missing codes
12
INL
Integral nonlinearity
–1
±0.25
1
LSB
DNL
Differential nonlinearity
–0.99
±0.25
1
LSB
EIO
Input offset error
–1
±0.5
1
mV
–1
±0.5
1
EIO match
ADC_A to ADC_B
Bits
mV
μV/°C
dEIO/dT
Input offset thermal drift
±1
EG
Gain error
Referenced to the voltage at REFIO_x
–0.1
±0.05
0.1
EG match
ADC_A to ADC_B
–0.1
±0.05
0.1
dEG/dT
Gain error thermal drift
Referenced to the voltage at REFIO_x
±1
ppm/°C
CMRR
Common-mode rejection ratio
Both ADCs, dc to 20 kHz
70
dB
73.4
dB
73.4
dB
VREF = 5 V (external),
±VREF input range
73.9
dB
VREF = 2.5 V,
±VREF input range
73.5
dB
73.5
dB
74
dB
VREF = 2.5 V,
±VREF input range
–92
dB
VREF = 2.5 V,
±2 × VREF input range
–92
dB
VREF = 5 V (external),
±VREF input range
–92
dB
VREF = 2.5 V,
±VREF input range
95
dB
VREF = 2.5 V,
±2 × VREF input range
95
dB
VREF = 5 V (external),
±VREF input range
95
dB
–100
dB
%FS
%FS
AC ACCURACY (2)
VREF = 2.5 V,
±VREF input range
SINAD
SNR
VREF = 2.5 V,
±2 × VREF input range
Signal-to-noise + distortion
72.4
VREF = 2.5 V,
±2 × VREF input range
Signal-to-noise ratio
72.5
VREF = 5 V (external),
±VREF input range
THD
SFDR
ISOXT
(1)
(2)
8
Total harmonic distortion
Spurious-free dynamic range
ADC-to-ADC isolation
fIN = 15 kHz at 10 %FS,
fNOISE = 25 kHz at FS
LSB = least significant bit.
All ac parameters are tested at –0.5 dBFS and a 20-kHz input frequency.
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
7.8 Electrical Characteristics: All Devices
All minimum and maximum specifications are at TA = –40°C to 125°C, AVDD = 5 V, DVDD = 3.3 V, VREF_A = VREF_B = VREF =
2.5 V, and fDATA = maximum, unless otherwise noted.
Typical values are at TA = 25°C, AVDD = 5 V, and DVDD = 3.3 V.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
–VREF
VREF
V
ANALOG INPUT
±VREF range
(1)
FSR
Full-scale input range
(AINP_x – AINM_x)
–2 × VREF
2 × VREF
V
±VREF range
0
VREF
V
VIN
Absolute input voltage
(AINP_x and AINM_x to
REFGND)
±2 × VREF range, AVDD ≥ 2 × VREF
0
2 × VREF
V
Common-mode voltage
range
(AINP_x + AINM_x) / 2
±VREF range
(VREF / 2) – 0.1
VREF / 2 (VREF / 2) + 0.1
V
VCM
Ci
Input capacitance
Ilkg(i)
Input leakage current
±2 × VREF range, AVDD ≥ 2 × VREF
±2 × VREF range
VREF – 0.1
In sample mode
VREF
VREF + 0.1
V
40
In hold mode
pF
4
pF
0.1
µA
INTERNAL VOLTAGE REFERENCE
VREFOUT
Reference output voltage
REFDAC_x = 1FFh (default),
at 25°C
VREF-match
VREF_A to VREF_B matching
REFDAC_x = 1FFh (default),
at 25°C
2.495
REFDAC_x resolution (2)
2.500
2.505
V
±1
mV
1.1
mV
dVREFOUT/dT
Reference voltage
temperature drift
REFDAC_x = 1FFh (default)
±10
ppm/°C
dVREFOUT/dt
Long-term stability
1000 hours
150
ppm
RO
Internal reference output
impedance
1
Ω
IREFOUT
Reference output dc
current
2
mA
CREFOUT
Recommended output
capacitor
10
µF
tREFON
Reference output settling
time
8
ms
For CREF = 10 μF
VOLTAGE REFERENCE INPUT
VREF
Reference voltage (input)
IREF
Average Reference input
current
CREF
External ceramic
reference capacitance
Ilkg(dc)
DC leakage current
±VREF range
2.4
2.5
AVDD
V
±2 × VREF range
2.4
2.5
AVDD / 2
V
Per ADC
300
μA
10
μF
±0.1
μA
SAMPLING DYNAMICS
tA
Aperture delay
tA match
tAJIT
(1)
(2)
ADC_A to ADC_B
Aperture jitter
8
ns
40
ps
50
ps
Ideal input span, does not include gain or offset error.
Refer to the Reference section for more details.
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
9
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
Electrical Characteristics: All Devices (continued)
All minimum and maximum specifications are at TA = –40°C to 125°C, AVDD = 5 V, DVDD = 3.3 V, VREF_A = VREF_B = VREF =
2.5 V, and fDATA = maximum, unless otherwise noted.
Typical values are at TA = 25°C, AVDD = 5 V, and DVDD = 3.3 V.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
DIGITAL INPUTS (3)
VIH
High-level input voltage
VIL
Low-level input voltage
DVDD > 2.3 V
0.7 DVDD
DVDD + 0.3
V
DVDD ≤ 2.3 V
0.8 DVDD
DVDD + 0.3
V
DVDD > 2.3 V
–0.3
0.3 DVDD
V
DVDD ≤ 2.3 V
–0.3
0.2 DVDD
V
Input current
±10
nA
DIGITAL OUTPUTS (3)
VOH
High-level output voltage
IOH = 500-µA source
VOL
Low-level output voltage
IOH = 500-µA sink
0.8 DVDD
DVDD
V
0
0.2 DVDD
V
POWER SUPPLY
AVDD
Analog supply voltage
(AVDD to AGND)
±VREF
range
±2 × VREF
range
DVDD
AIDD
DIDD
PD
(3)
(4)
10
Internal reference
4.5
5.0
5.5
V
External reference:
VEXT_REF < 4.5 V
4.5
5.0
5.5
V
External reference:
VEXT_REF > 4.5 V
VEXT_REF
5.0
5.5
V
5.0
5.0
5.5
V
2 × VREF_EXT
5.0
5.5
V
5.5
V
10
mA
Internal reference
External reference
Digital supply voltage
(DVDD to AGND)
Analog supply current
Digital supply current
Power dissipation
(normal operation)
1.65
AVDD = 5 V, fastest throughput
internal reference
8.5
AVDD = 5 V, fastest throughput
external reference (4)
7.5
AVDD = 5 V, no conversion
internal reference
5.5
AVDD = 5 V, no conversion
external reference (4)
4.5
mA
AVDD = 5 V, STANDBY mode
Internal Reference
2.5
mA
AVDD = 5 V, STANDBY mode
external reference (4)
1
mA
mA
7
μA
Power-down mode
10
DVDD = 3.3 V, CLOAD = 10 pF,
fastest throughput
0.5
mA
1
mA
DVDD = 5 V, CLOAD = 10 pF
fastest throughput
AVDD = 5V, fastest throughput,
internal reference
42.5
50
mA
50
mW
Specified by design; not production tested.
With internal reference powered down, CFR.B6 = 0.
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
7.9 Timing Requirements: Interface Mode (1)
PARAMETER
ASSOCIATED FIGURES
tCLK
CLOCK period
Figure 1, Figure 90, Figure 91, Figure 92, Figure 93
tACQ
Acquisition time
Figure 90, Figure 91, Figure 92, Figure 93
tCONV
Conversion time
Figure 90, Figure 91, Figure 92, Figure 93
(1)
These parameters are specific to the interface mode of operation. Refer to the Conversion Data Read section for more details.
7.10 Timing Characteristics: Serial Interface
PARAMETER
TEST CONDITIONS
ASSOCIATED FIGURES
MIN
TYP
MAX
UNIT
TIMING REQUIREMENTS
tPH_CK
CLOCK high time
tPL_CK
CLOCK low time
fCLK
CLOCK frequency
tPH_CS
CS high time
0.4
Figure 1
Figure 1
ADS8354
tPH_CS_SHRT
CS high time after frame abort
ADS7854
Figure 98
ADS7254
tSU_CSCK
Setup time: CS falling edge to
SCLK falling edge
tD_CKCS
Delay time: Last SCLK falling edge
to CS rising edge
tSU_CKDI
Setup time: DIN data valid to SCLK
falling edge
tHT_CKDI
Hold time: SCLK falling edge to
(previous) data valid on DIN
tPU_STDBY
Power-up time from STANDBY
mode
tPU_SPD
Power-up time from SPD mode
0.4
0.6
tCLK
0.6
tCLK
1 / tCLK
MHz
40
ns
150
ns
100
ns
70
ns
15
ns
15
ns
5
ns
5
ns
1
µs
3
ms
1
ms
1.425
µs
1
µs
Figure 1
Figure 95
With internal reference
With external reference
Figure 97
TIMING SPECIFICATIONS
ADS8354
tTHROUGHPUT
ADS7854
Throughput time
ADS7254
32-CLK mode
32-CLK mode
Figure 90, Figure 91
16-CLK mode
Figure 92, Figure 93
1
µs
32-CLK mode
Figure 90, Figure 91
1
µs
16-CLK mode
Figure 92, Figure 93
1
µs
Figure 90, Figure 91,
Figure 92, Figure 93
fTHROUGHPUT
Throughput
tDV_CSDO
Delay time: CS falling edge to data
enable
tDZ_CSDO
Delay time: CS rising edge to data
going to 3-state
tD_CKDO
Delay time: SCLK falling edge to
next data valid
Figure 1
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
1 / tTHROUGHPUT
kSPS
12
ns
12
ns
20
ns
Submit Documentation Feedback
11
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
Figure 1 shows the details of the serial interface between the device and the digital host controller.
CS
CS
tSU_CSCK
SCLK
1
2
1
SCLK
2
12
13
14
tSU_CKDI
tDV_CSDO
SDO
B14
B15
SDI
15
16
tHT_CKDI
B4
B3
B2
B1
Sample
N+1
Sample
N
tPH_CS
CS
SCLK
1
2
N9
tSCLK
tPL_CK
tPH_CK
N8
N7
N6
N5
N4
N3
N2
tD_CKDO
tD_CKCS
N1
N
tDZ_CSDO
SDOADS8353/4
V
V
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
SDOADS7853/4
V
V
D7
D6
D5
D4
D3
D2
D1
D0
0
0
SDOADS7253/4
V
V
D5
D4
D3
D2
D1
D0
0
0
0
0
Figure 1. Serial Interface Timing Diagram
12
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
7.11 Typical Characteristics: ADS8354
0
0
±25
±25
±50
±50
Signal Power (dB)
Signal Power (dB)
At TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (internal), and fDATA = 700 kSPS, unless otherwise noted.
±75
±100
±125
±75
±100
±125
±150
±150
±175
±175
±200
0
50
100
150
200
250
300
Input Frequency (kHz)
fIN = 20 kHz
350
±200
0
50
100
SNR = 89.5 dB
THD = –100 dB
fIN = 250 kHz
Signal-to-Noise and Distoirtion Ratio (dB)
Signal-to-Noise Ratio (dB)
89
88
87
86
85
26
59
92
C202
THD = –98 dB
88
87
86
85
±40
26
±7
59
92
125
Free-Air Temperature (oC)
C204
fIN = 2 kHz
Figure 4. SNR vs Temperature
Figure 5. SINAD vs Temperature
Signal-to-Noise and Distortion Ratio (dB)
95
Signal-to-Noise Ratio (dB)
350
89
C203
fIN = 2 kHz
94
93
92
91
90
2.5
300
90
125
Free-Air Temperature (oC)
2
250
Figure 3. Typical FFT
90
±7
200
SNR = 82.2 dB
Figure 2. Typical FFT
±40
150
Input Frequency (kHz)
C201
3
3.5
4
4.5
Reference Voltage (V)
fIN = 2 kHz
5
5.5
95
94
93
92
91
90
89
2
2.5
3
3.5
4
4.5
5
Reference Voltage (V)
C205
5.5
C206
fIN = 2 kHz
Figure 6. SNR vs Reference Voltage
Figure 7. SINAD vs Reference Voltage
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
13
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
Typical Characteristics: ADS8354 (continued)
At TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (internal), and fDATA = 700 kSPS, unless otherwise noted.
Signal-to-Noise and Distortion Ratio (dB)
Signal-to-Noise Ratio (dB)
90
88
86
84
82
80
0
50
100
150
200
250
Input Frequency (kHz)
90
88
86
84
82
80
300
0
50
Figure 8. SNR vs Input Frequency
250
300
C208
Figure 9. SINAD vs Input Frequency
±95
Total Harmonic Distortion (dB)
Total Harmonic Distortion (dB)
200
VREF = 5 V
±90
±92
±94
±96
±98
±100
±96
±97
±98
±99
±100
±40
26
±7
59
92
Free-Air Temperature (oC)
2
125
2.5
3
3.5
4
4.5
5
Reference Voltage (V)
C209
fIN = 2 kHz
5.5
C211
fIN = 2 kHz
Figure 10. THD vs Temperature
Figure 11. THD vs Reference Voltage
65536
±85
±89
49152
Number of Hits
Total Harmonic Distortion (dB)
150
Input Frequency (kHz)
VREF = 5 V
±93
±97
32768
16384
±101
0
±105
0
50
100
150
200
250
Input Frequency (kHz)
VREF = 5 V
Submit Documentation Feedback
300
-3
1
Output Code
C213
65536 data points
Figure 12. THD vs Input Frequency
14
100
C207
5
C215
VIN-DIFF = 0 V
Figure 13. DC Histogram
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
Typical Characteristics: ADS8354 (continued)
At TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (internal), and fDATA = 700 kSPS, unless otherwise noted.
10
10
IAVDD Dynamic (mA)
IAVDD Dynamic (mA)
9
9
8
7
8
7
6
5
6
4
±40
±7
26
59
92
Free-Air Temperature (oC)
125
0
100
75
75
50
50
25
0
±25
±50
18
24
30
C226
Figure 15. Analog Supply Current vs SCLK Frequency
100
Gain Error (m%)
Offset Error (uV)
12
SCLK Frequency (MHz)
Figure 14. Analog Supply Current vs Temperature
25
0
±25
±50
±75
±75
±100
±100
±40
±7
26
59
92
Free-Air Temperature (oC)
125
±40
26
±7
59
92
Free-Air Temperature (oC)
C216
Figure 16. Offset Error vs Temperature
125
C217
Figure 17. Gain Error vs Temperature
2
2
1.5
Integral Nonlinearity (LSB)
Differential Nonlinearity (LSB)
6
C224
1
0.5
0
-0.5
-1
±32768
32768
Output Code
Figure 18. Typical DNL
1
0
±1
±2
±32768
32768
Output Code
C218
C219
Figure 19. Typical INL
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
15
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
Typical Characteristics: ADS8354 (continued)
At TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (internal), and fDATA = 700 kSPS, unless otherwise noted.
2
1.5
1.5
Integral Nonlinearity (LSB)
Differential Nonlinearity (LSB)
2
Maximum
1
0.5
0
Minimum
-0.5
Maximum
1
0.5
0
-0.5
-1
Minimum
-1.5
-1
-2
±40
26
±7
59
92
125
Free-Air Temperature (oC)
±40
92
125
C221
Figure 21. INL vs Temperature
2
2
1.5
1.5
Integral Nonlinearity (LSB)
Differential Nonlinearity (LSB)
59
Free-Air Temperature (oC)
Figure 20. DNL vs Temperature
1
Maximum
0.5
0
Minimum
-0.5
Maximum
1
0.5
Minimum
0
-0.5
-1
-1.5
-1
-2
2
2.5
3
3.5
4
4.5
5
Reference Voltage (V)
Figure 22. DNL vs Reference Voltage
16
26
±7
C220
Submit Documentation Feedback
5.5
2
2.5
3
3.5
4
4.5
5
Reference Voltage (V)
C222
5.5
C223
Figure 23. INL vs Reference Voltage
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
7.12 Typical Characteristics: ADS7854
0
0
-25
-25
-50
-50
Signal Power (dB)
Signal Power (dB)
At TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (internal), and fDATA = 1 MSPS, unless otherwise noted.
-75
-100
-125
-75
-100
-125
-150
-150
-175
-175
-200
-200
0
100
200
300
400
Input Frequency (kHz)
fIN = 2 kHz
16-CLK interface
SNR = 83.8 dB
500
0
100
THD = –96.1 dB
fIN = 100 kHz
16-CLK interface
400
500
C002
THD = –93.1 dB
Figure 25. Typical FFT
0
0
±25
-25
±50
-50
Signal Power (dB)
Signal Power (dB)
300
SNR = 83.5 dB
Figure 24. Typical FFT
±75
±100
±125
-75
-100
-125
±150
-150
±175
-175
-200
±200
0
100
200
300
400
Input Frequency (kHz)
fIN = 2 kHz
32-CLK interface
SNR = 84.9 dB
0
500
100
THD = –98.7 dB
fIN = 100 kHz
32-CLK interface
Signal-to-Noise and Distortion Ratio (dB)
16 CLK Mode
84
32 CLK Mode
83
82
81
26
59
Free-Air Temperatrure
400
500
C002
THD = –95.1 dB
Figure 27. Typical FFT
85
-7
300
SNR = 84.4 dB
Figure 26. Typical FFT
-40
200
Input Frequency (kHz)
C051
86
Signal-to-Noise Ratio (dB)
200
Input Frequency (kHz)
C001
92
(oC)
fIN = 2 kHz
125
86
85.5
85
84.5
84
32 CLK Mode
83.5
83
16 CLK Mode
82.5
82
81.5
81
-40
-7
C003
26
59
Free-Air Temperature (oC)
92
125
C004
fIN = 2 kHz
Figure 28. SNR vs Temperature
Figure 29. SINAD vs Temperature
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
17
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
Typical Characteristics: ADS7854 (continued)
At TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (internal), and fDATA = 1 MSPS, unless otherwise noted.
85
Signal-to-Noise and Distortion Ratio (dB)
Signal-to-Noise Ratio (dB)
86
32 CLK Mode
84
16 CLK Mode
83
82
81
2
2.5
3
3.5
4
4.5
Reference Voltage (V)
5
86
85
32 CLK Mode
84
83
16 CLK Mode
82
81
5.5
2
fIN = 2 kHz
Signal-to-Noise and Distortion Ratio (dB)
Signal-to-Noise Ratio (dB)
85
32 CLK Mode
84
83
16 CLK Mode
82
81
50
100
150
200
Input Frequency (kHz)
250
5
5.5
C006
86
85
32 CLK Mode
84
83
82
16 CLK Mode
81
300
0
50
100
150
200
Input Frequency (kHz)
C007
VREF = 5 V
250
300
C008
VREF = 5 V
Figure 32. SNR vs Input Frequency
Figure 33. SINAD vs Input Frequency
-92
-92
-93
Total Harmonic Distortion (dB)
16 CLK Mode
Total Harmonic Distortion (dB)
3.5
4
4.5
Reference Voltage (V)
Figure 31. SINAD vs Reference Voltage
86
-94
-96
32 CLK Mode
-98
-100
-94
16 CLK Mode
-95
-96
-97
-98
32 CLK Mode
-99
-100
-101
-102
-102
-40
-7
26
59
92
Free-Air Temperature (oC)
fIN = 2 kHz
Submit Documentation Feedback
125
2
2.5
3
3.5
4
4.5
5
Reference Voltage (V)
C009
5.5
C011
fIN = 2 kHz
Figure 34. THD vs Temperature
18
3
fIN = 2 kHz
Figure 30. SNR vs Reference Voltage
0
2.5
C005
Figure 35. THD vs Reference Voltage
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
Typical Characteristics: ADS7854 (continued)
At TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (internal), and fDATA = 1 MSPS, unless otherwise noted.
10
16 CLK Mode
-92
32 CLK Mode
IAVDD Dynamic (mA)
Total Harmonic Distortion (dB)
-90
-94
-96
32 CLK Mode
-98
-100
0
50
100
150
200
250
Input Frequency (kHz)
9
16 CLK Mode
8
7
6
300
-40
-7
26
59
92
Free-Air Temperature (oC)
C013
125
C026
VREF = 5 V
Figure 37. Analog Supply Current vs Temperature
10
10
9
9
IAVDD Dynamic (mA)
IAVDD Dynamic (mA)
Figure 36. THD vs Input Frequency
8
7
6
7
6
5
5
4
4
0
4
8
12
16
SCLK Frequency (MHz)
0
20
8
16
24
32
SCLK Frequency (MHz)
C030
40
C056
32-CLK interface
16-CLK interface
Figure 39. Analog Supply Current vs SCLK Frequency
Figure 38. Analog Supply Current vs SCLK Frequency
65536
65536
49152
49152
Number of Hits
Number of Hits
8
32768
16384
32768
16384
0
0
8191
8192
8193
Output Code
16-CLK interface
65536 data points
Figure 40. DC Histogram
8191
8192
VIN-DIFF = 0 V
8193
Output Code
C015
32-CLK interface
65536 data points
C053
VIN-DIFF = 0 V
Figure 41. DC Histogram
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
19
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
Typical Characteristics: ADS7854 (continued)
At TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (internal), and fDATA = 1 MSPS, unless otherwise noted.
500
100
400
75
50
200
Gain Error (m%)
Offset Error (µV)
300
16 CLK Mode
100
0
-100
32 CLK Mode
-200
16 CLK Mode
25
0
32 CLK Mode
-25
-50
-300
-75
-400
-500
-100
-40
-7
26
59
92
Free-Air Temperature (oC)
125
-40
Figure 42. Offset Error vs Temperature
1
1
0.75
0.75
0.5
0.25
0
-0.25
-0.5
-0.75
C019
0.5
0.25
0
-0.25
-0.5
-1
-8192
8191
Output Code
8191
Output Code
C020
16-CLK interface
C021
16-CLK interface
Figure 44. Typical DNL
Figure 45. Typical INL
1
1
0.75
0.75
Integral Nonlinearity (LSB)
Differential Nonlinearity (LSB)
125
-0.75
-1
-8192
0.5
0.25
0
-0.25
-0.5
-0.75
0.5
0.25
0
-0.25
-0.5
-0.75
-1
±8192
8191
Output Code
32-CLK interface
-1
±8192
8191
Output Code
C054
C055
32-CLK interface
Figure 46. Typical DNL
20
26
59
92
Free-Air Temperature (oC)
Figure 43. Gain Error vs Temperature
Integral Nonlinearity (LSB)
Differential Nonlinearity (LSB)
-7
C018
Submit Documentation Feedback
Figure 47. Typical INL
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
Typical Characteristics: ADS7854 (continued)
At TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (internal), and fDATA = 1 MSPS, unless otherwise noted.
1
0.75
0.75
Integral Nonlinearity (LSB)
Differential Nonlinearity (LSB)
1
Maximum 16 CLK Mode
0.5
Maximum 32 CLK Mode
0.25
0
-0.25
Minimum 32 CLK Mode
-0.5
Minimum 16 CLK Mode
Maximum 16 CLK Mode
0.5
Maximum 32 CLK Mode
0.25
0
-0.25
Minimum 32 CLK Mode
-0.5
-0.75
-0.75
-1
-1
Minimum 16 CLK Mode
-40
-7
26
59
92
Free-Air Temperature (oC)
-40
125
26
59
92
125
Free-Air Temperature (oC)
Figure 48. DNL vs Temperature
C023
Figure 49. INL vs Temperature
1
1
Maximum 16 CLK Mode
0.75
Maximum 16 CLK Mode
0.75
0.5
Integral Nonlinearity (LSB)
Differential Nonlinearity (LSB)
-7
C022
Maximum 32 CLK Mode
0.25
0
Minimum 32 CLK Mode
-0.25
-0.5
-0.75
Minimum 16 CLK Mode
2.5
3
3.5
4
4.5
5
Reference Voltage (V)
Figure 50. DNL vs Reference Voltage
0.25
Maximum 32 CLK Mode
0
-0.25
Minimum 32 CLK Mode
-0.5
-0.75
-1
2
0.5
5.5
Minimum 16 CLK Mode
-1
2
2.5
C024
3
3.5
4
4.5
Reference Voltage (V)
5
5.5
C025
Figure 51. INL vs Reference Voltage
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
21
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
7.13 Typical Characteristics: ADS7254
0
0
±25
±25
±50
±50
Signal Power (dB)
Signal Power (dB)
At TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (internal), and fDATA = 1 MSPS, unless otherwise noted.
±75
±100
±125
±75
±100
±125
±150
±150
±175
±175
±200
±200
0
100
200
300
400
Input Frequency (kHz)
fIN = 2 kHz
16-CLK interface
SNR = 73.5 dB
500
0
100
THD = –91.1 dB
fIN = 250 kHz
16-CLK interface
0
±25
±25
±50
±50
Signal Power (dB)
Signal Power (dB)
400
500
C102
THD = –88.2 dB
Figure 53. Typical FFT
0
±75
±100
±125
±75
±100
±125
±150
±150
±175
±175
±200
±200
0
100
200
300
400
Input Frequency (kHz)
fIN = 2 kHz
32-CLK interface
SNR = 73.7 dB
500
0
100
THD = –92 dB
fIN = 250 kHz
32-CLK interface
Signal-to-Noise and Distortion Ratio (dB)
32 CLK Mode
16 CLK Mode
73
72
71
70
26
59
92
Free-Air Temperature (oC)
fIN = 2 kHz
500
C152
THD = –88.3 dB
125
75
32 CLK Mode
74
16 CLK Mode
73
72
71
70
±40
±7
26
59
92
Free-Air Temperature (oC)
C103
125
C104
fIN = 2 kHz
Figure 56. SNR vs Temperature
Submit Documentation Feedback
400
Figure 55. Typical FFT
74
±7
300
SNR = 73.6 dB
Figure 54. Typical FFT
±40
200
Input Frequency (kHz)
C151
75
Signal-to-Noise Ratio (dB)
300
SNR = 73.2 dB
Figure 52. Typical FFT
22
200
Input Frequency (kHz)
C101
Figure 57. SINAD vs Temperature
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
Typical Characteristics: ADS7254 (continued)
At TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (internal), and fDATA = 1 MSPS, unless otherwise noted.
Signal-to-Noise and Distortion Ratio (dB)
75
Signal-to-Noise Ratio (dB)
32 CLK Mode
74
16 CLK Mode
73
72
71
70
2
2.5
3
3.5
4
4.5
5
Reference Voltage (V)
75
32 CLK Mode
74
16 CLK Mode
73
72
71
70
5.5
2
4
4
5
5
6
C106
fIN = 2 kHz
Figure 58. SNR vs Reference Voltage
Figure 59. SINAD vs Reference Voltage
75
Signal-to-Noise and Distortion (dB)
75
32 CLK Mode
Signal-to-Noise Ratio (dB)
3
Reference Voltage (V)
fIN = 2 kHz
74
73
16 CLK Mode
72
71
70
16 CLK Mode
74
73
32 CLK Mode
72
71
70
0
50
100
150
200
250
Input Frequency (kHz)
300
0
50
100
150
200
250
Input Frequency (kHz)
C107
VREF = 5 V
300
C108
VREF = 5 V
Figure 60. SNR vs Input Frequency
Figure 61. SINAD vs Input Frequency
±80
Total Harmonic Distortion (dB)
±80
Total Harmonic Distortion (dB)
3
C105
±84
±88
32 CLK Mode
±92
16 CLK Mode
±96
±100
±84
±88
16 CLK Mode
±92
32 CLK Mode
±96
±100
±40
±7
26
59
92
Free-Air Temperature (oC)
fIN = 2 kHz
125
2
2.5
3
3.5
4
4.5
5
Reference Voltage (V)
C109
5.5
C111
fIN = 2 kHz
Figure 62. THD vs Temperature
Figure 63. THD vs Reference Voltage
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
23
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
Typical Characteristics: ADS7254 (continued)
At TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (internal), and fDATA = 1 MSPS, unless otherwise noted.
10
32 CLK Mode
±84
IAVDD Dynamic (mA)
Total Harmonic Distortion (dB)
±80
±88
16 CLK Mode
±92
32 CLK Mode
9
16 CLK Mode
8
7
±96
6
±100
0
50
100
150
200
250
Input Frequency (kHz)
300
±40
±7
26
59
92
Free-Air Temperature (oC)
C113
125
C124
VREF = 5 V
Figure 65. Analog Supply Current vs Temperature
10
9
9
IAVDD Dynamic (mA)
IAVDD Dynamic (mA)
Figure 64. THD vs Input Frequency
10
8
7
6
6
4
4
0
4
8
12
16
SCLK Frequency (MHz)
0
20
8
16
24
32
SCLK Frequency (MHz)
C030
40
C126
32-CLK interface
16-CLK interface
Figure 67. Analog Supply Current vs SCLK Frequency
Figure 66. Analog Supply Current vs SCLK Frequency
65536
65536
49152
49152
Number of Hits
Number of Hits
7
5
5
32768
16384
32768
16384
0
0
2047
2048
2049
Output Code
16-CLK interface
65536 data points
Figure 68. DC Histogram
24
8
Submit Documentation Feedback
2047
2048
Output Code
C153
VIN-DIFF = 0 V
32-CLK interface
65536 data points
2046
C115
VIN-DIFF = 0 V
Figure 69. DC Histogram
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
Typical Characteristics: ADS7254 (continued)
At TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (internal), and fDATA = 1 MSPS, unless otherwise noted.
100
100
16 CLK Mode
75
75
50
32 CLK Mode
Gain Error (m%)
Offset Error (µV)
50
25
0
±25
25
0
±25
±50
±50
±75
±75
±100
16 CLK Mode
32 CLK Mode
±100
±40
±7
26
59
92
Free-Air Temperature (oC)
125
±40
92
125
C117
Figure 71. Gain Error vs Temperature
1
1
0.75
1
Integral Nonlinearity (LSB)
Differential Nonlinearity (LSB)
59
Free-Air Temperature (oC)
Figure 70. Offset Error vs Temperature
0.5
0.25
0
-0.25
-0.5
-0.75
1
0
0
±0
±1
±1
-1
±2048
±1
±2048
2048
Output Code
2048
Output Code
C118
16-CLK interface
C119
16-CLK interface
Figure 72. Typical DNL
Figure 73. Typical INL
1
1
0.75
0.75
Integral Nonlinearity (LSB)
Differential Nonlinearity (LSB)
26
±7
C116
0.5
0.25
0
-0.25
-0.5
-0.75
0.5
0.25
0
-0.25
-0.5
-0.75
-1
±2048
2048
Output Code
32-CLK interface
-1
±2048
2048
Output Code
C154
C155
32-CLK interface
Figure 74. Typical DNL
Figure 75. Typical INL
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
25
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
Typical Characteristics: ADS7254 (continued)
1
1
0.75
0.75
0.5
Integral Nonlinearity (LSB)
Differential Nonlinearity (LSB)
At TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (internal), and fDATA = 1 MSPS, unless otherwise noted.
Maximum 16 CLK Mode
0.25
Maximum 32 CLK Mode
0
Minimum 16 CLK Mode
-0.25
-0.5
Minimum 32 CLK Mode
-0.75
0.5
Maximum 16 CLK Mode
0.25
Maximum 32 CLK Mode
0
Minimum 32 CLK Mode
-0.25
Minimum 16 CLK Mode
-0.5
-0.75
-1
-1
±40
26
±7
59
92
125
Free-Air Temperature (oC)
±40
0.75
1
0.5
Maximum 16 CLK Mode
Maximum 32 CLK Mode
Minimum 16 CLK Mode
-0.25
Minimum 32 CLK Mode
-0.5
-0.75
125
C121
1
Maximum 32 CLK Mode
0
Maximum 16 CLK Mode
0
±0
Minimum 32 CLK Mode
±1
Minimum 16 CLK Mode
±1
-1
±1
2
2.5
3
3.5
4
4.5
5
Reference Voltage (V)
Figure 78. DNL vs Reference Voltage
26
92
Figure 77. INL vs Temperature
1
Integral Nonlinearity (LSB)
Differential Nonlinearity (LSB)
Figure 76. DNL vs Temperature
0
59
Free-Air Temperature (oC)
1
0.25
26
±7
C120
Submit Documentation Feedback
5.5
2
2.5
3
3.5
4
4.5
5
Reference Voltage (V)
C122
5.5
C123
Figure 79. INL vs Reference Voltage
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
7.14 Typical Characteristics: Common to ADS8354, ADS7854, and ADS7254
At TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (internal), and fDATA = maximum, unless otherwise noted.
200
3
IAVDD Power Down (mA)
IAVDD STANDBY (mA)
2.5
16 CLK Mode
2
1.5
32 CLK Mode
1
0.5
160
120
80
40
16 CLK Mode
-40
-7
26
59
92
Free-Air Temperature (oC)
-40
125
-7
26
59
92
Free- AirTemperature (oC)
C027
Figure 80. STANDBY Current vs Temperature
125
C028
Figure 81. Power-Down Current vs Temperature
2.55
2.6
Internal Reference Output (V)
Internal Reference Output (V)
32 CLK Mode
0
0
2.53
2.51
2.49
2.47
2.45
-40
-7
26
59
Free-Air Temperature (oC)
92
125
2.55
2.5
2.45
2.4
2.35
2.3
-5
0
C016
5
10
15
Load Current (mA)
20
25
30
C017
ROUT = 0.67 Ω
Figure 82. Internal Reference Output vs Temperature
Figure 83. Internal Reference Output Impedance
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
27
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
8 Detailed Description
8.1 Overview
These devices belong to a family of pin-compatible, dual, high-speed, simultaneous-sampling, analog-to-digital
converters (ADCs). The ADS8354, ADS7854, and ADS7254 support fully-differential input signals. The devices
provide a simple, serial interface to the host controller and operate over a wide range of analog and digital power
supplies.
These devices have two independently programmable internal references to achieve system-level gain error
correction. The Functional Block Diagram section provides a functional block diagram of the device.
8.2 Functional Block Diagram
REF_A
Comparator
S/H
CDAC
SAR
ADC_A
ADC_B
S/H
Serial
Interface
SAR
CDAC
Comparator
REF_B
28
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
8.3 Feature Description
8.3.1 Reference
The device has two simultaneous sampling ADCs (ADC_A and ADC_B). ADC_A and ADC_B operate with
reference voltages VREF_A and VREF_B present on the REFIO_A and REFIO_B pins, respectively. The REFIO_A
and REFIO_B pins should be decoupled with the REFGND_A and REFGND_B pins, respectively, with 10-µF
decoupling capacitors.
The device supports operation either with an internal or external reference source, as shown in Figure 84. The
reference voltage source is determined by setting bit 6 of the configuration register (CFR.B6). Note that this bit is
common to ADC_A and ADC_B.
AINP_A
AINM_A
ADC_A
REFGND_A
REFDAC_A
DAC_A
10 PF
REFIO_A
CFR.B6
Enable
INTREF
REFIO_B
REFDAC_B
10 PF
DAC_B
REFGND_B
AINP_B
AINM_B
ADC_B
Figure 84. Reference Configurations and Connections
When CFR.B6 is 0, the device shuts down the internal reference source (INTREF) and ADC_A and ADC_B
operate on external reference voltages provided by the user on the REFIO_A and REFIO_B pins, respectively.
When CFR.B6 is 1, the device operates with the internal reference source (INTREF) connected to REFIO_A and
REFIO_B via DAC_A and DAC_B, respectively. In this configuration, VREF_A and VREF_B can be changed
independently by writing to the respective user-programmable registers, REFDAC_A and REFDAC_B,
respectively. Refer to the REFDAC Registers (REFDAC_A and REFDAC_B) section for more details.
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
29
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
Feature Description (continued)
8.3.2 Analog Inputs
The ADS8354, ADS7854, and ADS7254 support fully-differential analog input signals on both ADC channels.
These inputs are sampled and converted simultaneously by the two ADCs, ADC_A and ADC_B. ADC_A
samples and converts (VAINP_A – VAINM_A), and ADC_B samples and converts (VAINP_B – VAINM_B).
Figure 85a and Figure 85b show equivalent circuits for the ADC_A and ADC_B analog input pins, respectively.
Series resistance, RS, represents the on-state sampling switch resistance (typically 50 Ω) and CSAMPLE is the
device sampling capacitor (typically 40 pF).
AVDD
AVDD
RS
CSAMPLE
AINP_A
RS
CSAMPLE
RS
CSAMPLE
AINP_B
GND
GND
AVDD
AVDD
RS
CSAMPLE
AINM_A
AINM_B
GND
GND
a) ADC_A
b) ADC_B
Figure 85. Equivalent Circuit for the Analog Input Pins
8.3.2.1 Analog Input: Full-Scale Range Selection
The full-scale range (FSR) supported at the analog inputs of the device is programmable with bit B9 of the
configuration register (CFR.B9). This bit is common for both ADCs (ADC_A and ADC_B). The FSR is given by
Equation 1 and Equation 2 :
For CFR.B9 = 0, FSR_ADC_A = ±VREF_A and FSR_ADC_B = ±VREF_B
For CFR.B9 = 1, FSR_ADC_A = ±2 × VREF_A and FSR_ADC_B = ±2 × VREF_B
(1)
where:
•
VREF_A and VREF_B are the reference voltages going to ADC_A and ADC_B, respectively (as described in the
Reference section).
(2)
Therefore, with appropriate settings of the REFDAC_A and REFDAC_B registers and CFR.B9, the maximum
dynamic range of the ADC can be used.
Note that while using CFR.B9 set to 1, care must be taken so that the ADC analog supply (AVDD) is as in
Equation 3 and Equation 4:
2 × VREF_A ≤ AVDD ≤ AVDD(max)
2 × VREF_B ≤ AVDD ≤ AVDD(max)
30
Submit Documentation Feedback
(3)
(4)
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
Feature Description (continued)
8.3.2.2 Analog Input: Common-Mode Voltage Range
The ADS8354, ADS7854, and ADS7254 support fully-differential input signals. Equation 5 and Equation 6
provide the common-mode voltage for the ADC_A and ADC_B differential inputs.
VCM_A = FSR_ADC_A / 2
VCM_B = FSR_ADC_B / 2
(5)
(6)
The various input configurations supported by the device are shown in Table 1.
Table 1. Input Configurations
INPUT RANGE SELECTION
INPUT COMMON-MODE
RANGE
CONNECTION DIAGRAM
VREF_x
VREF_x
REFIO_x
VREF_x / 2
AINP_x
VREF_A
CFR.B9 = 0
(FSR_ADC_A = ±VREF_A)
(FSR_ADC_B = ±VREF_B)
VCM_A =
r 0.1 V
2
0V
Device
VREF_B
VCM_B =
2
r 0.1 V
VREF_x
AINM_x
VREF_x / 2
0V
2 u VREF_x
VREF_x
REFIO_x
VREF_x
AINP_x
0V
CFR.B9 = 1
(FSR_ADC_A = ±2 × VREF_A)
(FSR_ADC_B = ±2 × VREF_B)
VCM_A = VREF_A r 0.1 V
Device
VCM_B = VREF_B r 0.1 V
2 u VREF_x
AINM_x
VREF_x
0V
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
31
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
8.3.3 Transfer Function
The device output is in twos compliment format. Device resolution for a fully-differential input is calculated by
Equation 7:
1 LSB = (2 × FSR_ADC_x) / (2N)
where:
•
•
N = 16 (ADS8354), 14 (ADS7854), or 12 (ADS7254)
FSR_ADC_x is the full-scale input range of the ADC (refer to the Analog Input section for more details)
(7)
Table 2 shows the different input voltages and the corresponding output codes from the device.
Table 2. Transfer Characteristics
INPUT VOLTAGE
(AINP_x – AINM_x),
±VREF RANGE
INPUT VOLTAGE
(AINP_x – AINM_x),
±2 × VREF RANGE
INPUT
VOLTAGE
CODE
ADS8354
OUTPUT CODE (Hex)
ADS7854
ADS7254
< – VREF_x
< –2 × VREF_x
NFSC
NFSC
8000
2000
800
–VREF_x + 1 LSB
–2 × VREF_x + 1 LSB
NFSR
NFSC + 1
8001
2001
801
–1 LSB
–1 LSB
–1 LSB
MC
FFFF
3FFF
FFF
0
0
0
PLC
0000
0000
000
> VREF_x – 1 LSB
> 2 × VREF_x – 1 LSB
PFSR – 1 LSB
PFSC
7FFF
1FFF
7FF
Figure 86 shows the ideal transfer characteristics for the device.
ADC Code (Hex)
PFSC
PLC
MC
NFSC + 1
NFSC
NFSR
1 LSB
0
VIN
PFSR ± 1 LSB
Fully-Differential Analog Input
(AINP_x ± AINM_x)
Figure 86. Ideal Transfer Characteristics for a Fully-Differential Analog Input
32
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
8.4 Device Functional Modes
The device provides three user-programmable registers: the configuration register (CFR), the REFDAC_A
register, and the REFDAC_B register. These registers support write (refer to the Write to User Programmable
Registers section) and readback (refer to the Reading User-Programmable Registers section) operations and
allow the user to customize ADC behavior for specific application requirements.
The device supports four interface modes (refer to the Conversion Data Read section), two low-power modes
(refer to the Low-Power Modes section), and short-cycling/reconversion feature (refer to the Frame Abort,
Reconversion, or Short-Cycling section).
8.5 Register Maps and Serial Interface
8.5.1 Serial Interface
The device uses the serial clock (SCLK) for synchronizing data transfers in and out of the device.
The CS signal defines one conversion and serial transfer frame. A frame starts with a CS falling edge and ends
with a CS rising edge. Between the start and end of the frame, a minimum of N SCLK falling edges must be
provided to validate the read or write operation. As shown in Table 3, N depends upon the interface mode used
to read the conversion result. When N SCLK falling edges are provided, the write operation attempted in the
frame is validated and the internal user-programmable registers are updated on the subsequent CS rising edge.
This CS rising edge also ends the frame.
Table 3. SCLK Falling Edges for a Valid Write Operation
INTERFACE MODE
MINIMUM SCLK FALLING EDGES REQUIRED TO
VALIDATE WRITE OPERATION N
32-CLK, dual-SDO mode (default). See the 32-CLK, Dual-SDO Mode section.
32
32-CLK, single-SDO mode. See the 32-CLK, Single-SDO Mode section.
48
16-CLK, dual-SDO mode. See the 16-CLK, Dual-SDO Mode section.
16
16-CLK, single SDO mode. See the 16-CLK, Single SDO Mode section.
32
If CS is brought high before providing N SCLK falling edges, the write operation attempted in the frame is not
valid. Refer to the Frame Abort, Reconversion, or Short-Cycling section for more details.
8.5.2 Write to User Programmable Registers
The device features three user-programmable registers: the configuration register (CFR), the REFDAC_A
register, and the REFDAC_B register. These registers can be written with the device SDI pin. The first 16 bits of
data on SDI are latched into the device on the first 16 SCLK falling edges. However, the new configuration takes
effect only when the read or write operation is validated. If these registers are not required to update, SDI must
remain low during the respective frames.
The first four SDI data bits (B[15:12]) determine what operation is performed (that is, either a read or write
operation or no operation), which register address the operation uses, and the function of the next 12 SDI data
bits (B[11:0]). Table 4 lists the various combinations supported for B[15:12].
Table 4. Data Write Operation
B15
B14
B13
B12
OPERATION
FUNCTION OF BITS B[11:0]
0
0
0
0
No operation is performed
These bits are ignored
0
0
0
1
REFDAC_A read
000h; see the Reading User-Programmable Registers section
0
0
1
0
REFDAC_B read
000h; see the Reading User-Programmable Registers section
0
0
1
1
CFR read
000h; see the Reading User-Programmable Registers section
1
0
0
0
CFR write
See the Configuration Register (CFR) section
1
0
0
1
REFDAC_A write
See the REFDAC_A section
1
0
1
0
REFDAC_B write
See the REFDAC_B section
1
0
1
1
No operation is performed
These bits are ignored
X
1
X
X
No operation is performed
These bits are ignored
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
33
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
8.5.2.1 Configuration Register (CFR)
The device operation configuration is controlled by the configuration register (CFR) status. Data written into the
CFR in a valid frame (F) determine the device configuration for frame (F+1). The bit functions are outlined in
Figure 87. On power-up, all bits in the CFR default to 0.
Figure 87. CFR Bit Functions
15
14
13
12
WRITE/READ
0
ADDR1
ADDR0
7
0
6
REF_SEL
5
STANDBY
4
0
11
RD_CLK_
MODE
3
0
10
RD_DATA_
LINES
2
0
9
8
INPUT_RANGE
0
1
0
0
0
Table 5. Configuration Register (CFR) Field Descriptions
Bit
Field
Type
Reset
15
WRITE/READ
W
0h
14
0
R/W
0h
13
ADDR1
R/W
0h
12
ADDR0
R/W
0h
11
10
RD_DATA_LINES
R/W
R/W
These bits select the user-programmable register.
1000 = Select this combination to write to the CFR register and
to enable bits 11:0
0h
This bit provides clock mode selection for the serial interface.
0 = Selects 32-CLK mode (default)
1 = Selects 16-CLK mode
(Note that the ADS8354 only supports 32-CLK mode. This bit is
ignored for the ADS8354.)
0h
This bit provides data line selection for the serial interface.
0 = Use SDO_A to output ADC_A data and SDO_B to output of
ADC_B data (default)
1 = Use only SDO_A to output of ADC_A data followed by
ADC_B data
INPUT_RANGE
R/W
0h
This bit selects the maximum input range for the ADC as a
function of the reference voltage provided to the ADC. See the
Analog Inputs section for more details.
0 = FSR equals ±VREF
1 = FSR equals ±2 × VREF
0
R/W
0h
This bit must be set to 0 (default)
6
REF_SEL
R/W
0h
This bit selects the ADC reference voltage source. Refer to the
Reference section for more details.
0 = Use external reference (default)
1 = Use internal reference
5
STANDBY
W
0h
This bit is used by the device to enter or exit STANDBY mode.
Refer to the STANDBY Mode section for more details.
4
0
R/W
0h
This bit must be set to 0 (default)
3:0
0
R/W
0h
These bits must be set to 0 (default)
9
8:7
34
RD_CLK_MODE
Description
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
8.5.2.2 REFDAC Registers (REFDAC_A and REFDAC_B)
The REFDAC registers, bit functions, and resolution information are described in this section.
Figure 88. REFDAC_X Bit Functions
15
WRITE/READ
7
D4
14
0
6
D3
13
ADDR1
5
D2
12
ADDR0
4
D1
11
D8
3
D0
10
D7
2
0
9
D6
1
0
8
D5
0
0
Table 6. REFDAC Registers Field Descriptions
Bit
Field
Type
Reset
Description
15
WRITE/READ
W
0h
14
0
R/W
0h
13
ADDR1
R/W
0h
12
ADDR0
R/W
0h
These bits select the configurable register address.
1001 = Select this combination to write to the REFDAC_A
register
1010 = Select this combination to write to the REFDAC_B
register
11:3
D[8:0]
R/W
0h
Data to program the individual DAC output voltage.
Note: These bits are valid only for bits 15:12 = 1001 or bits
15:12 = 1010.
Table 7 shows the relationship between the REFDAC_x
programmed value and the DAC_x output voltage.
2:0
0
R/W
0h
This bit must be set to 0 (default)
Table 7. REFDAC Settings
REFDAC_x VALUE (Bits 11:3 in Hex)
B[2:0]
Typical DAC_x OUPTUT VOLTAGE (V) (1)
1FF (default)
000
2.5000
1FE
000
2.4989
1FD
000
2.4978
—
—
—
1D7
000
2.45
—
—
—
1AE
000
2.40
—
—
—
186
000
2.35
(1)
—
—
—
15D
000
2.30
—
—
—
134
000
2.25
—
—
—
10C
000
2.20
—
—
—
0E3
000
2.15
—
—
—
0BA
000
2.10
—
—
—
091
000
2.05
—
—
—
069
000
2.00
—
—
—
064 to 000
000
Do not use
Actual output voltage may vary by a few millivolts from the specified value. To obtain the desired output voltage, TI recommends starting
with the specified register setting and then experimenting with five codes on either side of the specified register setting.
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
35
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
8.5.3 Data Read Operation
The device supports two types of read operations: reading user-programmable registers and reading conversion
results.
8.5.3.1 Reading User-Programmable Registers
The device supports a readback option for all user-programmable registers: CFR, REFDAC_A, and REFDAC_B.
Figure 89 shows a detailed timing diagram for this operation.
Frame (F)
Frame (F+1)
Frame (F+2)
Frame (F+3)
CS
SCLK
1
2
N
1
2
4
3
5
16
48
SDO-A
Valid Data
Valid data as per device configuration.
SDO-B
Valid Data
Valid data as per device configuration.
SDI
No change in device
configuration
B14 B13 B12
B15
X
X
X
1
2
R15 R14
15
16
47
R1
R0
1
48
2
N
Valid Data
Valid Data
X
No change in device
configuration
Device configuration for frame (F+3)
Note that N is a function of the device configuration, as described in Table 3.
Figure 89. Register Readback Timing
To readback the user-programmable register settings, the appropriate control word should be transmitted to the
device during frame (F+1), as shown in Table 8. Frame (F+1) must have at least 48 SCLK falling edges.
Table 8. Control Word to Readback User-Programmable Registers
CONTROL WORD TO BE PROGRAMMED IN FRAME (F+1)
USER-PROGRAMMABLE REGISTER
B[15:12] (Binary)
B[11:0] (Hex)
CFR
0011b
000h
REFDAC_A
0001b
000h
REFDAC_B
0010b
000h
Frame (F+2) must have at least 48 SCLK falling edges. During frame (F+2), SDO_A outputs the contents of the
selected user-programmable register on the first 16 SCLK falling edges (as shown in Table 9) and then outputs
0s for any subsequent SCLK falling edges. The SDO_B pin outputs 0s for all the SCLK falling edges.
Table 9. Register Data Read Back
USERPROGRAMMABLE
REGISTER
DATA READ ON SDO-A IN FRAME (F+2)
R15
R14
R13
R12
CFR
0
0
1
REFDAC_A
0
0
REFDAC_B
0
0
R11
—
R3
R2
R1
R0
1
CFG.B11
—
CFG.B3
CFG.B2
CFG.B1
CFG.B0
0
1
REFDAC_A.D8
—
1
0
REFDAC_B.D8
—
REFDAC_A.D0
0
0
0
REFDAC_B.D0
0
0
0
Register settings programmed during frame (F+2) determine the device configuration in frame (F+3).
36
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
8.5.3.2 Conversion Data Read
The device provides four different interface modes to the user for reading the conversion result. These modes
offer flexible hardware connections and firmware programming. Table 10 shows how to select one of the four
interface modes.
Table 10. Interface Mode Selection
CFR.B11
CFR.B10
INTERFACE MODE
MINIMUM SCLK FALLING EDGES
REQUIRED TO VALIDATE WRITE
OPERATION N
0
0
32-CLK, dual-SDO mode (default)
32
0
1
32-CLK, single-SDO mode
48
1
0
16-CLK, dual-SDO mode
16
1
1
16-CLK, single SDO mode
32
In the 32-CLK interface modes, the device uses an internal clock to convert the sampled analog signal. The
conversion is completed during the first 16 periods of SCLK and the conversion result can be read on the
subsequent SCLK falling edges. All devices in the family (that is, ADS8354, ADS7854, and ADS7254) support
the 32-CLK interface modes.
In addition to the 32-CLK interface modes, the ADS7854 and ADS7254 also support the 16-CLK interface
modes. By using the 16-CLK interface modes, the same throughput can be achieved at much lower SCLK
speeds.
The following sections detail the various interface modes supported by the device.
8.5.3.2.1 32-CLK, Dual-SDO Mode (CFR.B11 = 0, CFR.B10 = 0, Default)
The 32-CLK, dual-SDO mode is the default mode supported by all devices. This mode can also be selected by
writing CFR.B11 = 0 and CFR.B10 = 0.
In this mode, the SDO_A pin outputs the ADC_A conversion result and the SDO_B pin outputs the ADC_B
conversion result. Figure 90 shows a detailed timing diagram for this mode.
Sample
N
Sample
N+1
tTHROUGHPUT
tCONV
tACQ
CS
tSCLK
SCLK
1
2
14
15
16
ADS8353, ADS8354
SDO_A and SDO_B
17
18
25
26
27
D15
D14
D7
D6
D5
28
29
D4
30
31
32
D3
D2
D1
D0
D1
D0
0
0
0
0
0
0
Data From Sample N
ADS7853, ADS7854
SDO_A and SDO_B
D13
D12
D5
D4
D3
D2
Data From Sample N
ADS7253, ADS7254
SDO_A and SDO_B
D11
D10
D3
D2
D1
D0
Data From Sample N
SDI
B15
B14
B2
B1
B0
X
X
X
X
X
X
X
X
X
X
Figure 90. 32-CLK, Dual-SDO Mode Timing Diagram
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
37
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
A CS falling edge brings the serial data bus out of 3-state and also outputs a 0 on the SDO_A and SDO_B pins.
The device converts the sampled analog input during the conversion time (tCONV). SDO_A and SDO_B read 0
during this period. After completing the conversion process, the sample-and-hold circuit returns to sample mode.
The device outputs the MSBs of ADC_A and ADC_B on SDO_A and SDO_B pins, respectively, on the 16th
SCLK falling edge. The subsequent SCLK falling edges are used to shift out the rest of the bits of the conversion
result, as shown in Table 11.
Table 11. Data Launch Edge
LAUNCH EDGE
DEVICE
ADS8354
ADS7854
ADS7254
PINS
CS
SCLK
↓
↓1
—
—
↓27
↓28
↓29
↓30
↓31
↓32 ...
↑
SDO-A
0
0
—
0 D15_A
—
D4_A
D3_A
D2_A
D1_A
D0_A
0 ...
Hi-Z
SDO-B
0
0
—
0 D15_B
—
D4_B
D3_B
D2_B
D1_B
D0_B
0 ...
Hi-Z
SDO-A
0
0
—
0 D13_A
—
D2_A
D1_A
D0_A
0
0
0 ...
Hi-Z
SDO-B
0
0
—
0 D13_B
—
D2_B
D1_B
D0_B
0
0
0 ...
Hi-Z
SDO-A
0
0
—
0 D11_A
—
D0_A
0
0
0
0
0 ...
Hi-Z
SDO-B
0
0
—
0 D11_B
—
D0_B
0
0
0
0
0 ...
Hi-Z
↓15 ↓16
CS
In this mode, at least 32 SCLK falling edges must be given to validate the read or write frame. A CS rising edge
ends the frame and puts the serial bus into 3-state.
Refer to Table 12 for timing specifications specific to this serial interface mode.
Table 12. 32-CLK, Dual-SDO Interface Specific Timing
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
TIMING REQUIREMENTS
tCLK
CLOCK period
tACQ
Acquisition time
ADS8354
41.66
ns
ADS7854
29.4
ns
ADS7254
29.4
ns
33 × tCLK – tCONV
ns
TIMING SPECIFICATIONS
tCONV
38
Conversion time
Submit Documentation Feedback
ADS8354
640
ns
ADS7854
450
ns
ADS7254
450
ns
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
8.5.3.2.2 32-CLK, Single-SDO Mode (CFR.B11 = 0, CFR.B10 = 1)
The 32-CLK, single-SDO mode provides the option of using only one SDO pin (SDO_A) to read conversion
results from both ADCs (ADC_A and ADC_B). SDO_B remains in 3-state and can be treated as a no connect
(NC) pin.
This mode can be selected by writing CFR.B11 = 0 and CFR.B10 = 1. Figure 91 shows a detailed timing diagram
for this mode.
Sample
N
Sample
N+1
tTHROUGHPUT
tCONV
tACQ
CS
SCLK
1
2
14
15
16
17
28
18
ADS8353, ADS8354
SDO_A
D1
5-A
D1
4-A
ADS7853, ADS7854
SDO_A
D1
3-A
D1
2-A
ADS7253, ADS7254
SDO_A
D1
1-A
D1
0-A
29
D4A
31
30
D3A
D2A
33
32
34
45
44
47
46
48
D1A
D0A
D1
5-B
D4B
D3B
D2B
D1B
D0B
0
0
D1
3-B
D2B
D1B
D0B
0
0
0
0
D1
1-B
D0B
0
0
0
0
X
X
X
X
X
X
Data From Sample N
D2A
D1A
D0A
Data From Sample N
D0A
0
0
Data From Sample N
All Devices
SDO_B
SDI
B15
B14
B3
B2
B1
B0
X
X
X
X
X
X
X
Figure 91. 32-CLK, Single-SDO Mode Timing Diagram
A CS falling edge brings the serial data bus out of 3-state and also outputs a 0 on the SDO_A pin. The device
converts the sampled analog input during the conversion time (tCONV). SDO_A reads 0 during this period. After
competing the conversion process, the sample-and-hold circuit goes back into sample mode. The device outputs
the MSB of ADC_A on the SDO_A pin on the 16th SCLK falling edge. The subsequent SCLK falling edges are
used to shift out the conversion result of ADC_A followed by the conversion result of ADC_B on the SDO_A pin,
as shown in Table 13.
Table 13. Data Launch Edge
LAUNCH EDGE
DEVICE
PIN
CS
SCLK
↓
↓1
—
↓15
↓16
—
↓27
↓28
↓29
↓30
↓31
CS
↓32
—
↓43
↓44
↓45
↓46
↓47
↓48 ...
D15_B
—
↑
D4_B
D3_B
D2_B
D1_B
D0_B
0 ...
Hi-Z
ADS8354
SDO-A
0
0
—
0
D15_A
—
D4_A
D3_A
D2_A
D1_A
D0_A
ADS7854
SDO-A
0
0
—
0
D13_A
—
D2_A
D1_A
D0_A
0
0
0
—
D2_B
D1_B
D0_B
0
0
0 ...
Hi-Z
ADS7254
SDO-A
0
0
—
0
D11_A
—
D0_A
0
0
0
0
0
—
D0_B
0
0
0
0
0 ...
Hi-Z
In this mode, at least 48 SCLK falling edges must be given to validate the read or write frame. A CS rising edge
ends the frame and puts the serial bus into 3-state.
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
39
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
Refer to Table 14 for timing specifications specific to this serial interface mode.
Table 14. 32-CLK, Single-SDO Interface Specific Timing
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
TIMING REQUIREMENTS
tCLK
tACQ
CLOCK period
ADS8354
41.66
ns
ADS7854
29.4
ns
ADS7254
29.4
ns
Acquisition time
49 × tCLK – tCONV
ns
TIMING SPECIFICATIONS
tCONV
Conversion time
ADS8354
640
ns
ADS7854
450
ns
ADS7254
450
ns
8.5.3.2.3 16-CLK, Dual-SDO Mode (CFR.B11 = 1, CFR.B10 = 0)
The 16-CLK, dual-SDO mode is designed to support the maximum throughput at lower SCLK frequencies. This
interface mode is not supported by the ADS8354.
For the ADS7854 and ADS7254, this interface mode can be selected by writing CFR.B11 = 1 and CFR.B10 = 0.
In this mode, the SDO_A pin outputs the ADC_A conversion result and the SDO_B pin outputs the ADC_B
conversion result. Figure 92 shows a detailed timing diagram for this mode.
Sample
N
Sample
N+1
tTHROUGHPUT
tPH_CS
CS
tSCLK
SCLK
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
tCONV
ADS7853, ADS7854
SDO_A and SDO_B
0
0
D13
D12
D11
D10
D9
D8
tACQ
D7
D6
D5
D4
D3
D2
D1
tCONV
ADS7253, ADS7254
SDO_A and SDO_B
0
0
D11
D10
D9
D8
D7
D0
tACQ
D6
D5
D4
D3
D2
D1
D0
0
0
Data From Sample N
SDI
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
Figure 92. 16-CLK, Dual-SDO Mode Timing Diagram
40
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
A CS falling edge brings the serial data bus out of 3-state and also outputs a 0 on the SDO_A and SDO_B pins.
The subsequent SCLK falling edges are used for conversion and for data transfer using the serial interface, as
shown in Table 15.
The sample-and-hold circuit goes back into sample mode as soon as the conversion process is over.
Table 15. Data Launch Edge
LAUNCH EDGE
DEVICE
ADS7854
ADS7254
PINS
CS
SCLK
CS
↓
↓1
↓2
—
↓13
↓14
↓15
↓16 ...
↑
SDO-A
0
0
D13_A
—
D2_A
D1_A
D0_A
0 ...
Hi-Z
SDO-B
0
0
D13_B
—
D2_B
D1_B
D0_B
0 ...
Hi-Z
SDO-A
0
0
D11_A
—
D0_A
0
0
0 ...
Hi-Z
SDO-B
0
0
D11_B
—
D0_B
0
0
0 ...
Hi-Z
In this mode, at least 16 SCLK falling edges must be given to validate the read or write frame. A CS rising edge
ends the frame and puts the serial bus into 3-state.
Refer to Table 16 for timing specifications specific to this serial interface mode.
Table 16. 16-CLK, Dual-SDO Interface Specific Timing
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
TIMING REQUIREMENTS
tCLK
tACQ
CLOCK period
Acquisition time
ADS7854
55.5
ADS7254
55.5
ns
ns
ADS7854
4 × tCLK
ns
ADS7254
6 × tCLK
ns
ADS7854
14 × tCLK
ns
ADS7254
12 × tCLK
ns
TIMING SPECIFICATIONS
tCONV
Conversion time
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
41
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
8.5.3.2.4 16-CLK, Single-SDO Mode (CFR.B11 = 1, CFR.B10 = 1)
The 16-CLK, single-SDO mode provides the option of using only one SDO pin (SDO_A) and a lower-speed clock
to read the conversion results of both ADCs. This interface mode is not supported by the ADS8354.
For the ADS7854 and ADS7254, this mode can be selected by writing CFR.B11 = 1 and CFR.B10 = 1. The
SDO_A pin is used to output the conversion results of both ADCs (ADC_A and ADC_B). SDO_B remains in 3state and can be treated as a no connect (NC) pin. Figure 93 shows a detailed timing diagram for this mode.
Sample
N
Sample
N+1
tTHROUGHPUT
tPH_CS
CS
tSCLK
SCLK
1
2
3
4
5
14
13
15
16
17
18
19
20
21
D13B
D12B
tCONV
ADS7853, ADS7854
SDO_A
0
0
D13A
D12A
0
0
D11A
31
32
tACQ
D11A
D2-A
D3-A
D1-A
D0-A
0
0
tCONV
ADS7253, ADS7254
SDO_A
30
D11D2-B
B
D1-B
D0-B
D9-B D0-B
0
0
tACQ
D10A
D9-A
D0-A
D1-A
0
0
0
D11B
0
D10B
Data From Sample N
All Devices
SDO_B
SDI
B15
B14
B13
B3
B12
B2
B1
B0
X
X
X
X
X
X
X
X
Figure 93. 16-CLK, Single-SDO Mode Timing Diagram
A CS falling edge brings the serial data bus out of 3-state and also outputs a 0 on the SDO_A pin. The
subsequent SCLK falling edges are used for conversion and for data transfer using the serial interface, as shown
in Table 17.
The sample-and-hold circuit goes back into sample mode as soon as the conversion process is over.
Table 17. Data Launch Edge
LAUNCH EDGE
DEVICE
PIN
CS
SCLK
↓
↓1
↓2
—
↓13
↓14
↓15
↓16
↓17
CS
↓18
—
↓29
↓30
↓31
↓32 ...
↑
ADS7854
SDO-A
0
0
D13_A
—
D2_A
D1_A
D0_A
0
0
D13_B
—
D2_B
D1_B
D0_B
0 ...
Hi-Z
ADS7254
SDO-A
0
0
D11_A
—
D0_A
0
0
0
0
D11_B
—
D0_B
0
0
0 ...
Hi-Z
42
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
In this mode, at least 32 SCLK falling edges must be given to validate the read/write frame. A CS rising edge
ends the frame and puts the serial bus into 3-state.
Refer to Table 18 for timing specifications specific to this serial interface mode.
Table 18. 16-CLK, Single-SDO Interface Specific Timing
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
TIMING REQUIREMENTS
tCLK
CLOCK period
tACQ
Acquisition time
ADS7854
55.5
ADS7254
55.5
ns
ns
ADS7854
19 × tCLK
ns
ADS7254
21 × tCLK
ns
ADS7854
14 × tCLK
ns
ADS7254
12 × tCLK
ns
TIMING SPECIFICATIONS
tCONV
Conversion time
8.5.4 Low-Power Modes
In normal mode of operation, all internal circuits of the device are always powered up and the device is always
ready to commence a new conversion. This mode enables the device to support the rated throughput. The
device also supports two low-power modes to optimize the power consumption at lower throughputs: STANDBY
mode and software power-down (SPD) mode.
8.5.4.1 STANDBY Mode
The device supports a STANDBY mode of operation where some of the internal circuits of the device are
powered down. However, if bit 6 in configuration register is set to 1 (CFR.B6 = 1), then the internal reference is
not powered down and the contents of the REFDAC_A and REFDAC_B registers are retained to enable faster
power-up to a normal mode of operation.
As shown in Figure 94, a valid write operation in frame (F) to program the configuration register with B5 set to 1
(CFR.B5 = 1) places the device into a STANDBY mode of operation on the following CS rising edge. While in
STANDBY mode, SDO_A and SDO_B output all 1s when CS is low and remain in 3-state when CS is high.
To remain in STANDBY mode, SDI must remain low in the subsequent frames.
Device enters
STANDBY mode
Frame (F)
Frame (F+1)
Device in
STANDBY mode
CS
SCLK
1
2
3
4
SDO-A and
SDO-B
5
6
7
8
9
10
11
12
13
14
15
16
N
1
2
Valid Data as per device configuration
CFG.B[5] = 1
SDI
CFG.B[15:12] = 1000b
CFG.B[11:6]
CFG.B[4:0] = 00000b
Note that N is a function of the device configuration, as described in Table 3.
Figure 94. Enter STANDBY Mode
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
43
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
As shown in Figure 95, a valid write operation in frame (F+3) by writing the configuration register with B5 set to 0
(CFR.B5 = 0) brings the device out of STANDBY mode on the following CS rising edge. Frame (F+3) must have
at least 48 SCLK falling edges.
After exiting the STANDBY mode, a delay of tPU_STDBY must elapse for the internal circuits to fully power-up and
resume normal operation in frame (F+4). Device configuration for frame (F+4) is determined by the status of the
CFR.B[11:6] bits programmed during frame (F+3).
Frame (F+2)
CS
SCLK
Frame (F+3)
Device in
STANDBY
mode
tPU_STDBY
1
2
3
4
5
SDO-A
and
SDO-B
SDI
Frame (F+4)
Device exits
STANDBY mode
6
7
8
9
10
11
12
13
14
15
16
48
CFG.B[11:6]
2
15
16
N
Valid Data as per device configuration
These bits set device
configuration for Frame (F+4)
CFG.B[5] = 0
CFG.B[15:12] = 1000b
1
CFG.B[4:0] = 00000b
CFG settings for Frame (F+5)
Note that N is a function of the device configuration, as described in Table 3.
Figure 95. Exit STANDBY Mode
Refer to the Timing Characteristics: Serial Interface for timing specifications for this operating mode.
44
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
8.5.4.2 Software Power-Down (SPD) Mode
In software power-down (SPD) mode, all internal circuits (including the internal references) are powered down.
However, the contents of the REFDAC_A and REFDAC_B registers are retained.
As shown in Figure 96, to enter SPD mode, the device must be selected (by bringing CS low) and SDI must be
kept high for a minimum of 48 SCLK cycles during frame (F). The device goes to SPD on the CS rising edge
following frame (F). While in SPD mode, SDO_A and SDO_B go to 3-state irrespective of the status of the CS
signal.
To remain in SPD mode, SDI must remain high in subsequent frames.
Device enters SPD
mode
Frame (F)
Frame (F+1)
Device in SPD
mode
CS
SCLK
1
2
SDO-A and
SDO-B
3
47
1
48
2
Valid Data as per device configuration
SDI
Figure 96. Enter SPD Mode
As shown in Figure 97, to exit SPD mode, the device must be selected (by bringing CS low) and SDI must be
kept low for a minimum of 48 SCLK cycles during frame (F+3). The device starts powering-up on a CS rising
edge following frame (F+3). After frame (F+3), a delay of tPU_SPD must elapse before programming the
configuration register.
A valid write operation in frame (F+4) sets the device configuration for frame (F+5). Frame (F+4) must have at
least 48 SCLK falling edges. The output data in frame (F+4) should be discarded.
Frame (F+2)
Frame (F+3)
Frame (F+4)
Device exits
SPD
Frame (F+5)
tPU_SPD
CS
SCLK
Device in
SPD
1
2
47
48
1
2
SDO-A
and
SDO-B
15
16
48
Invalid Data
SDI
CFG settings for Frame (F+5)
1
2
15
16
N
Valid Data as per device configuration
CFG settings for Frame (F+6)
Note that N is a function of the device configuration, as described in Table 3.
Figure 97. Exit SPD Mode
Refer to the Timing Characteristics: Serial Interface for timing specifications for this operating mode.
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
45
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
8.5.5 Frame Abort, Reconversion, or Short-Cycling
As discussed in Figure 98, the minimum number of SCLK falling edges (N) that must be provided between the
beginning and end of the frame depends on the serial interface mode. The SCLK falling edges (N) program the
device and retrieve the conversion result. If CS is brought high before the expected number of SCLK falling
edges are provided, the current frame is aborted and the device starts sampling the new analog input signal.
If frame (F) is aborted, then the register write operation attempted in frame (F) is considered invalid and the
internal registers are not updated. The device continues to have the same configuration in frame (F+1) from
frame (F).
The output data bits latched before the CS rising edge are still valid data that correspond to sample N.
tPL_CS
tPH_CS_SHRT
CS
1
SCLK
2
SDO
Sample
N
Sample
N+1
tCONV
tACQ
tPH_CS_SHRT
CS
SCLK
1
2
SDO
13
14
15
16
17
22
23
24
V
V
V
V
V
Data From Sample N
Figure 98. Frame Abort, Reconversion, or Short-Cycling Feature
Refer to the Timing Characteristics: Serial Interface for timing specifications for this operating mode.
46
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
9 Application and Implementation
9.1 Application Information
The two primary circuits required to maximize the performance of a high-precision, successive approximation
register (SAR), analog-to-digital converter (ADC) are the input driver and the reference driver circuits. This
section details some general principles for designing these circuits, and some application circuits designed using
these devices.
The device supports operation either with an internal or external reference source. Refer to the Reference
section for details about the decoupling requirements.
The reference source to the ADC must provide low-drift and very accurate dc voltage and support the dynamic
charge requirements without affecting the noise and linearity performance of the device. The output broadband
noise (typically in the order of a few 100 μVRMS) of the reference source must be appropriately filtered by using a
low-pass filter with a cutoff frequency of a few hundred hertz. After band-limiting the noise from the reference
source, the next important step is to design a reference buffer that can drive the dynamic load posed by the
reference input of the ADC. At the start of each conversion, the reference buffer must regulate the voltage of the
reference pin within 1 LSB of the intended value. This condition necessitates the use of a large filter capacitor at
the reference pin of the ADC. The amplifier selected to drive the reference input pin must be stable while driving
this large capacitor and should have low output impedance, low offset, and temperature drift specifications. To
reduce the dynamic current requirements and crosstalk between the channels, a separate reference buffer is
recommended for driving the reference input of each ADC channel.
The input driver circuit for a high-precision ADC mainly consists of two parts: a driving amplifier and a fly-wheel
RC filter. The amplifier is used for signal conditioning of the input voltage and its low output impedance provides
a buffer between the signal source and the switched capacitor inputs of the ADC. The RC filter helps attenuate
the sampling charge injection from the switched-capacitor input stage of the ADC and functions as an antialiasing
filter to band-limit the wideband noise contributed by the front-end circuit. Careful design of the front-end circuit is
critical to meet the linearity and noise performance of a high-precision ADC.
9.1.1 Input Amplifier Selection
Selection criteria for the input amplifiers is highly dependent on the input signal type and the performance goals
of the data acquisition system. Some key amplifier specifications to consider while selecting an appropriate
amplifier to drive the inputs of the ADC are:
• Small-signal bandwidth. Select the small-signal bandwidth of the input amplifiers to be as high as possible
after meeting the power budget of the system. Higher bandwidth reduces the closed-loop output impedance
of the amplifier, thus allowing the amplifier to more easily drive the low cutoff frequency RC filter at the ADC
inputs. Higher bandwidth also minimizes the harmonic distortion at higher input frequencies. In order to
maintain the overall stability of the input driver circuit, the amplifier bandwidth should be selected as
described in Equation 8:
§
1
Unity Gain Bandwidth t 4 u ¨¨
© 2S u ( RFLT RFLT ) u C FLT
•
·
¸¸
¹
(8)
Noise. Noise contribution of the front-end amplifiers should be as low as possible to prevent any degradation
in SNR performance of the system. As a rule of thumb, to ensure that the noise performance of the data
acquisition system is not limited by the front-end circuit, the total noise contribution from the front-end circuit
should be kept below 20% of the input-referred noise of the ADC. Noise from the input driver circuit is bandlimited by designing a low cutoff frequency RC filter and is calculated by Equation 9:
2
§ V 1 _ AM P_ PP ·
S
¨
¸
NG u 2 u ¨ f
en2 _ RM S u u f3dB
¸
6.6
2
¨
¸
©
¹
d
§ SNR dB ·
¸
20
¹
¨
1 VREF
u
u 10 ©
5
2
where:
•
•
•
•
V1 / f_AMP_PP is the peak-to-peak flicker noise in µV,
en_RMS is the amplifier broadband noise density in nV/√Hz,
f–3dB is the 3-dB bandwidth of the RC filter, and
NG is the noise gain of the front-end circuit, which is equal to 1 in a buffer configuration.
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
(9)
47
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
Application Information (continued)
•
Distortion. Both the ADC and the input driver introduce nonlinearity in a data acquisition block. As a rule of
thumb, to ensure that the distortion performance of the data acquisition system is not limited by the front-end
circuit, the distortion of the input driver should be at least 10 dB lower than the distortion of the ADC, as
shown in Equation 10.
THD AMP d THD ADC 10 dB
•
(10)
Settling Time. For dc signals with fast transients that are common in a multiplexed application, the input signal
must settle to the desired accuracy at the inputs of the ADC during the acquisition time window. This
condition is critical to maintain the overall linearity performance of the ADC. Typically, the amplifier data
sheets specify the output settling performance only up to 0.1% to 0.001%, which may not be sufficient for the
desired accuracy. Therefore, the settling behavior of the input driver should always be verified by TINA™SPICE simulations before selecting the amplifier.
9.1.2 Antialiasing Filter
Converting analog-to-digital signals requires sampling an input signal at a constant rate. Any higher frequency
content in the input signal beyond half the sampling frequency is digitized and folded back into the low-frequency
spectrum. This process is called aliasing. Therefore, an analog, antialiasing filter must be used to remove the
harmonic content from the input signal before being sampled by the ADC. An antialiasing filter is designed as a
low-pass, RC filter, for which the 3-dB bandwidth is optimized based on specific application requirements. For dc
signals with fast transients (including multiplexed input signals), a high-bandwidth filter is designed to allow
accurately settling the signal at the ADC inputs during the small acquisition time window. For ac signals, the filter
bandwidth should be kept low to band-limit the noise fed into the ADC input, thereby increasing the signal-tonoise ratio (SNR) of the system.
A filter capacitor, CFLT, connected across the ADC inputs (as shown in Figure 99), filters the noise from the frontend drive circuitry, reduces the sampling charge injection and provides a charge bucket to quickly charge the
internal sample-and-hold capacitors during the acquisition process. As a rule of thumb, the value of this capacitor
should be at least 10 times the specified value of the ADC sampling capacitance. For these devices, the input
sampling capacitance is equal to 40 pF. Thus, the value of CFLT should be greater than 400 pF. The capacitor
should be a COG- or NPO-type because these capacitor types have a high-Q, low-temperature coefficient, and
stable electrical characteristics under varying voltages, frequency, and time.
Note that driving capacitive loads can degrade the phase margin of the input amplifiers, thus making the amplifier
marginally unstable. To avoid amplifier stability issues, series isolation resistors (RFLT) are used at the output of
the amplifiers. A higher value of RFLT is helpful from the amplifier stability perspective, but adds distortion as a
result of interactions with the nonlinear input impedance of the ADC. Distortion increases with source impedance,
input signal frequency, and input signal amplitude. Therefore, the selection of RFLT requires balancing the stability
and distortion of the design. For these devices, TI recommends limiting the value of RFLT to a maximum of 22 Ω
in order to avoid any significant degradation in linearity performance. The tolerance of the selected resistors can
be chosen as 1% because the use of a differential capacitor at the input balances the effects resulting from any
resistor mismatch.
RFLT ”22
f 3 dB
2S u R FLT
1
R FLT u C FLT
CFLT •400 pF
VAINP
ADS8354
+
AINM
ADS7854
ADS7254
GND
RFLT ”22
Figure 99. Antialiasing Filter
The input amplifier bandwidth should be much higher than the cutoff frequency of the antialiasing filter. TI
strongly recommends performing a SPICE simulation to confirm that the amplifier has more than 40° phase
margin with the selected filter. If an amplifier has less than a 40° phase margin with 22-Ω resistors, using a
different amplifier with higher bandwidth or reducing the filter cutoff frequency with a larger differential capacitor
is advisable.
48
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
9.2 Typical Applications
9.2.1 DAQ Circuit to Achieve Maximum SINAD for a 10-kHz Input Signal at Full Throughput
1K 1K AVDD
AVDD
VIN+
VREF
VCM
+
10
+
THS4521
+
-
AVDD
V
AINP
+
ADSxx54
4.7 nF
AINM
10
GND
COG
(NPO)
+
VIN-
1K ADS8354 : 16-bit, 700 kSPS
ADS7854 : 14-bit, 1 MSPS
ADS7254 : 11-bit, 1 MSPS
1K INPUT DRIVER
NOTE: Only one ADC channel is shown in this diagram. Replicate the same circuit for other ADC channels.
Figure 100. DAQ Circuit: Maximum SINAD for a 10-kHz Input Signal at Full Throughput, 32-CLK Interface
1K 1K AVDD
AVDD
VIN+
VREF
VCM
+
10
+
THS4521
+
-
AVDD
V
AINP
+
ADSxx54
2.2 nF
AINM
10
GND
+
VIN-
COG
(NPO)
1K 1K ADS7854 : 14-bit, 1 MSPS
ADS7254 : 12-bit, 1 MSPS
INPUT DRIVER
NOTE: Only one ADC channel is shown in this diagram. Replicate the same circuit for other ADC channels.
Figure 101. DAQ Circuit: Maximum SINAD for a 10-kHz Input Signal at Full Throughput, 16-CLK Interface
AVDD
AVDD
REF5025,
REF5040,
REF5050(1)
10 µF
REFGND-A
1k +
0.1
AVDD
1 µF
ADC_A
REFIN-A
-
VOUT
Device
AVDD
TRIM
0.22
1k +
1 µF
REFIN-B
10 µF
1 µF
-
ADC_B
0.1
REFGND-B
OPA2350
10 µF
(1) When using the REF5050, AVDD must be set to 5.5 V.
Figure 102. Reference Drive Circuit
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
49
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
Typical Applications (continued)
9.2.1.1 Design Requirements
To design an application circuit optimized to achieve target specifications listed in Table 19.
Table 19. Target Specifications
TARGET SPECIFICATIONS
TEST CONDITIONS
SNR
THD
DEVICE
INPUT SIGNAL
FREQUENCY
THROUGHPUT
INTERFACE MODE
> 88 dB
< -100 dB
ADS8354
10 kHz
Maximum supported
32-CLK, dual-SDO
> 83.5 dB
< –95 dB
ADS7854
10 kHz
Maximum supported
32-CLK, dual-SDO
> 80.5 dB
< –88 dB
ADS7854
10 kHz
Maximum supported
16-CLK, dual-SDO
> 72.5 dB
< –88 dB
ADS7254
10 kHz
Maximum supported
32-CLK, dual-SDO
> 71.5 dB
< –85 dB
ADS7254
10 kHz
Maximum supported
16-CLK, dual-SDO
9.2.1.2 Detailed Design Procedure
Best practice is for the distortion from the input driver to be at least 10 dB less than the ADC distortion. The
distortion resulting from variation in the common-mode signal is eliminated by using a fully-differential amplifier
(FDA) that establishes a fixed common-mode level at the ADC input. The low-power THS4521, used as an input
driver, provides exceptional ac performance because of its extremely low-distortion and high-bandwidth
specifications. The output common-mode voltage of the THS4521 is set by the voltage provided on its VOCM pin.
In addition, the components of the antialiasing filter are such that the noise from the front-end circuit is kept low
without adding distortion to the input signal.
The application circuit illustrated in Figure 100 is optimized to achieve the lowest distortion and lowest noise for a
10-kHz input signal fed to the ADS8354 or ADS7854 or ADS7254 operating at full throughput with the default 32CLK, dual-SDO interface mode. The input signal is processed through a high-bandwidth, low-distortion, fullydifferential amplifier and a low-pass RC filter before being fed into the device.
The ADS7854 and the ADS7254 also support 16-CLK interface modes that achieve the rated throughput rate at
much lower SCLK frequencies. However, when using the 16-CLK interface modes, the device receives less
acquisition time when compared to the 32-CLK interface modes. The application circuit illustrated in Figure 101 is
optimized to achieve the lowest distortion and lowest noise for a 10-kHz input signal fed to the ADS7854 or
ADS7254 operating at full throughput with the 16-CLK, dual-SDO interface mode. The input signal is processed
through a high-bandwidth, low-distortion, fully-differential amplifier and a low-pass RC filter before being fed into
the device.
Figure 102 illustrates the reference driver circuit when operation with an external reference is desired. The
reference voltage is generated by the high-precision, low-noise REF50xx circuit. The output broadband noise of
the reference is heavily filtered by a low-pass filter with a 3-dB cutoff frequency of 160 Hz. The decoupling
capacitor on each reference pin is selected to be 10 µF. The low output impedance, low noise, and fast settling
time makes the OPA2350 a good choice for driving this high capacitive load.
50
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
9.2.1.3 Application Curves
To minimize external components and to maximize the dynamic range of the ADC, device is configured to
operate with internal reference (CFR.B6 = 1) and ±2 x VREF_x input full scale range (CFR.B9 = 1).
Figure 103, Figure 104, and Figure 105, show the FFT plots and test results obtained with the ADS8354,
ADS7854, and ADS7254, respectively, operating at full throughput with a 32-CLK interface and the circuit
configuration of Figure 100.
0
0
±20
±30
±60
Power (dB)
Signal Power (dB)
±40
±80
±100
±120
±60
±90
±140
±160
±120
±180
±200
0
70
140
210
280
Input Frequency (kHz)
SNR = 88.2 dB
THD = –101.4 dB
±150
350
0
100
200
300
400
Input Frequency (kHz)
C302
fIN = 10.1 kHz
SNR = 84.2 dB
Figure 103. ADS8354 in 32-CLK Interface Mode
THD = –98.4 dB
500
C003
fIN = 10.1 kHz
Figure 104. ADS7854 in 32-CLK Interface Mode
0
Power (dB)
±30
±60
±90
±120
±150
0
100
200
300
400
Input Frequency (kHz)
SNR = 73.3 dB
THD = –89.4 dB
500
C001
fIN = 10.1 kHz
Figure 105. ADS7254 in 32-CLK Interface Mode
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
51
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
0
0
±30
±30
Power (dB)
Power (dB)
Figure 106 and Figure 107 show the FFT plots and test results obtained with the ADS7854 and ADS7254,
respectively, operating at full throughput with 16-CLK interface and the circuit configuration of Figure 101.
±60
±90
±120
±90
±120
±150
±150
0
100
200
300
400
Input Frequency (kHz)
SNR = 81.1 dB
THD = –91.5 dB
Submit Documentation Feedback
500
0
100
fIN = 10.1 kHz
200
300
400
500
Input Frequency (kHz)
C004
Figure 106. ADS7854 in 16-CLK Interface Mode
52
±60
SNR = 72.8 dB
THD = –90.4 dB
C002
fIN = 10.1 kHz
Figure 107. ADS7254 in 16-CLK Interface Mode
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
9.2.2 DAQ Circuit to Achieve Maximum SINAD for a 100-kHz Input Signal at Full Throughput
(1)
330pF
1K 1K AVDD
AVDD
VIN+
FSR/2
VCM
+
10
+
AVDD
V
+
AINP
THS4521
+
-
820 pF
ADSxx54
AINM
10
GND
+
VIN-
1K 1K 330pF
ADS8354 : 16-bit, 700 kSPS
ADS7854 : 14-bit, 1 MSPS
ADS7254 : 12-bit, 1 MSPS
(1)
INPUT DRIVER
NOTE: Only one ADC channel is shown in this diagram. Replicate the same circuit for other ADC channels.
(1) The 330 pF capacitors are not required for ADS7854 and ADS7254.
Figure 108. DAQ Circuit: Maximum SINAD for a 100-kHz Input Signal at Full Throughput
AVDD
AVDD
REF5025,
REF5040,
REF5050(1)
10 µF
REFGND-A
1k +
0.1
AVDD
1 µF
ADC_A
REFIN-A
-
VOUT
Device
AVDD
TRIM
0.22
1k +
1 µF
REFIN-B
10 µF
1 µF
-
ADC_B
0.1
REFGND-B
OPA2350
10 µF
(1) When using the REF5050, AVDD must be set to 5.5 V.
Figure 109. Reference Drive Circuit
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
53
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
9.2.2.1 Design Requirements
To design an application circuit optimized to achieve target specifications listed in Table 20.
Table 20. Target Specifications
TARGET SPECIFICATIONS
TEST CONDITIONS
SNR
THD
DEVICE
INPUT SIGNAL
FREQUENCY
> 86 dB
< -95 dB
ADS8354
100 kHz
Maximum supported
32-CLK, dual-SDO
> 81.5 dB
< –90 dB
ADS7854
100 kHz
Maximum supported
32-CLK, dual-SDO
> 79.5 dB
< –88 dB
ADS7854
100 kHz
Maximum supported
16-CLK, dual-SDO
> 72 dB
< –88 dB
ADS7254
100 kHz
Maximum supported
32-CLK, dual-SDO
> 71 dB
< –85 dB
ADS7254
100 kHz
Maximum supported
16-CLK, dual-SDO
THROUGHPUT
INTERFACE MODE
9.2.2.2 Detailed Design Procedure
Best practice is for the distortion from the input driver to be at least 10 dB less than the ADC distortion. The
distortion resulting from variation in the common-mode signal is eliminated by using a fully-differential amplifier
(FDA) that establishes a fixed common-mode level at the ADC input. The low-power THS4521, used as an input
driver, provides exceptional ac performance because of its extremely low-distortion and high-bandwidth
specifications. The output common-mode voltage of the THS4521 is set by the voltage provided on its VOCM pin.
In addition, the components of the antialiasing filter are such that the noise from the front-end circuit is kept low
without adding distortion to the input signal.
The application circuit illustrated in Figure 108 is optimized to achieve the lowest distortion and lowest noise for a
100-kHz input signal fed to the ADS8354 or ADS7854 or ADS7254 operating at full throughput. The input signal
is processed through a high-bandwidth, low-distortion, fully-differential amplifier and a low-pass RC filter before
being fed into the device.
Figure 102 illustrates the reference driver circuit when operation with an external reference is desired. The
reference voltage is generated by the high-precision, low-noise REF50xx circuit. The output broadband noise of
the reference is heavily filtered by a low-pass filter with a 3-dB cutoff frequency of 160 Hz. The decoupling
capacitor on each reference pin is selected to be 10 µF. The low output impedance, low noise, and fast settling
time makes the OPA2350 a good choice for driving this high capacitive load.
54
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
9.2.2.3 Application Curves
To minimize external components and to maximize the dynamic range of the ADC, device is configured to
operate with internal reference (CFR.B6 = 1) and ±2 x VREF_x input full scale range (CFR.B9 = 1).
Figure 110, Figure 111, and Figure 112 show the FFT plots and test results obtained with the ADS8354,
ADS7854 and ADS7254, respectively, operating at full throughput with a 32-CLK interface and the circuit
configuration of Figure 108.
0
0
±20
±30
±60
Power (dB)
Signal Power (dB)
±40
±80
±100
±120
±60
±90
±140
±160
±120
±180
±200
0
70
140
210
280
Input Frequency (kHz)
SNR = 86.2 dB
THD = –97.5 dB
±150
350
0
100
C304
200
300
400
Input Frequency (kHz)
fIN = 100.2 kHz
SNR = 82.6 dB
Figure 110. ADS8354 in 32-CLK Interface Mode
THD = –93.1 dB
500
C007
fIN = 100.2 kHz
Figure 111. ADS7854 in 32-CLK Interface Mode
0
Power (dB)
±30
±60
±90
±120
±150
0
100
200
300
400
Input Frequency (kHz)
SNR = 72.9 dB
THD = –90.1 dB
500
C005
fIN = 100.2 kHz
Figure 112. ADS7254 in 32-CLK Interface Mode
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
55
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
0
0
±30
±30
Power (dB)
Power (dB)
Figure 113 and Figure 114 show the FFT plots and test results obtained with the ADS7854 and ADS7254,
respectively, operating with a 16-CLK interface and the circuit configuration of Figure 108.
±60
±90
±120
±90
±120
±150
±150
0
100
200
300
400
Input Frequency (kHz)
SNR = 80.3 dB
THD = –90.4 dB
Submit Documentation Feedback
500
0
100
fIN = 100.2 kHz
200
300
400
Input Frequency (kHz)
C008
Figure 113. ADS7854 in 16-CLK Interface Mode
56
±60
SNR = 72.5 dB
THD = –88.7 dB
500
C006
fIN = 100.2 kHz
Figure 114. ADS7254 in 16-CLK Interface Mode
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
10 Power-Supply Recommendations
The devices have two separate power supplies: AVDD and DVDD. The device operates on AVDD; DVDD is
used for the interface circuits. AVDD and DVDD can be independently set to any value within the permissible
ranges.
When using the device with ±2 × VREF input range (CFR.B9 = 1), the AVDD supply voltage value defines the
permissible voltage swing on the analog input pins. To avoid saturation of output codes, and to use the full
dynamic range on the analog input pins, AVDD must be set as shown in Equation 11, Equation 12, and
Equation 13:
AVDD ≥ 2 × VREF_A
AVDD ≥ 2 × VREF_B
4.75 V ≤ AVDD ≤ 5.25 V
(11)
(12)
(13)
Decouple the AVDD and DVDD pins with the GND pin using individual 10-µF decoupling capacitors, as shown in
Figure 115.
AVDD
AVDD (pin 14)
10 PF
GND (pin 13)
10 PF
DVDD
DVDD (pin 7)
Figure 115. Power-Supply Decoupling
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
57
ADS8354, ADS7854, ADS7254
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
www.ti.com
11 Layout
11.1 Layout Guidelines
Figure 116 shows a board layout example for the ADS8354, ADS7854, and ADS7254 with the WQFN package.
Use a ground plane underneath the device and partition the PCB into analog and digital sections. Avoid crossing
digital lines with the analog signal path and keep the analog input signals and the reference input signals away
from noise sources. As shown in Figure 116, the analog input and reference signals are routed on the left side of
the board and the digital connections are routed on the right side of the device.
The power sources to the device must be clean and well-bypassed. Use 10-μF, ceramic bypass capacitors in
close proximity to the analog (AVDD) and digital (DVDD) power-supply pins. Avoid placing vias between the
AVDD and DVDD pins and the bypass capacitors. Connect all ground pins to the ground plane using short, low
impedance paths.
The REFIO-A and REFIO-B reference inputs and outputs are bypassed with 10-μF, X7R-grade, 0805-size, 16-V
rated ceramic capacitors (CREF-x). Place the reference bypass capacitors as close as possible to the reference
REFIO-x pins and connect the bypass capacitors using short, low-inductance connections. Avoid placing vias
between the REFIO-x pins and the bypass capacitors. Small 0.1-Ω to 0.2-Ω resistors (RREF-x) are used in series
with the reference bypass capacitors to improve stability.
The fly-wheel RC filters are placed immediately next to the input pins. Among ceramic surface-mount capacitors,
COG (NPO) ceramic capacitors provide the best capacitance precision. The type of dielectric used in COG
(NPO) ceramic capacitors provides the most stable electrical properties over voltage, frequency, and temperature
changes. Figure 116 shows CIN-A and CIN-B filter capacitors placed across the analog input pins of the device.
11.2 Layout Example
CREF-A
AVDD
CIN-A
GND
GND
AVDD
AINP-A
AINM-A
RREF-A
CAVDD
GND
SDO-A
REFIO-A
CIN-B
/CS
SDI
AINM-B
RREF-B
CREF-B
SCLK
GND
REFIO-B
GND
SDO-B
REFGND-B
DVDD
GND
REFGND-A
AINP-B
GND
CDVDD
DVDD
GND
GND
Figure 116. Recommended Layout
58
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
ADS8354, ADS7854, ADS7254
www.ti.com
SBAS556B – OCTOBER 2013 – REVISED AUGUST 2014
12 Device and Documentation Support
12.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 21. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
ADS8354
Click here
Click here
Click here
Click here
Click here
ADS7854
Click here
Click here
Click here
Click here
Click here
ADS7254
Click here
Click here
Click here
Click here
Click here
12.2 Related Documentation
•
•
•
•
TIPD117 Verified Design Reference Guide: 12 Bit 1 MSPS Single Supply Dual Channel Data Acquisition
System for Optical Encoders in Motor Control Application Reference Design, SLAU517.
REF5050 Data Sheet, SBOS410.
OPA2350 Data Sheet, SBOS099.
THS4521 Data Sheet, SBOS458.
12.3 Trademarks
TINA is a trademark of Texas Instruments Inc..
All other trademarks are the property of their respective owners.
12.4 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
12.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: ADS8354 ADS7854 ADS7254
Submit Documentation Feedback
59
PACKAGE OPTION ADDENDUM
www.ti.com
7-Sep-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
ADS7254IPW
ACTIVE
TSSOP
PW
16
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
ADS7254
ADS7254IPWR
ACTIVE
TSSOP
PW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
ADS7254
ADS7254IRTER
ACTIVE
WQFN
RTE
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
7254
ADS7254IRTET
ACTIVE
WQFN
RTE
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
7254
ADS7854IPW
ACTIVE
TSSOP
PW
16
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
ADS7854
ADS7854IPWR
ACTIVE
TSSOP
PW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
ADS7854
ADS7854IRTER
ACTIVE
WQFN
RTE
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
7854
ADS7854IRTET
ACTIVE
WQFN
RTE
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
7854
ADS8354IPW
ACTIVE
TSSOP
PW
16
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
ADS8354
ADS8354IPWR
ACTIVE
TSSOP
PW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
ADS8354
ADS8354IRTER
ACTIVE
WQFN
RTE
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8354
ADS8354IRTET
ACTIVE
WQFN
RTE
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8354
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
7-Sep-2014
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Mar-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
ADS7254IPWR
TSSOP
PW
16
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
ADS7254IRTER
WQFN
RTE
16
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
ADS7254IRTET
WQFN
RTE
16
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
ADS7854IPWR
TSSOP
PW
16
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
ADS7854IRTER
WQFN
RTE
16
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
ADS7854IRTET
WQFN
RTE
16
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
ADS8354IPWR
TSSOP
PW
16
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
ADS8354IRTER
WQFN
RTE
16
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
ADS8354IRTET
WQFN
RTE
16
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Mar-2016
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ADS7254IPWR
ADS7254IRTER
TSSOP
PW
16
2000
367.0
367.0
35.0
WQFN
RTE
16
3000
367.0
367.0
35.0
ADS7254IRTET
WQFN
RTE
16
250
210.0
185.0
35.0
ADS7854IPWR
TSSOP
PW
16
2000
367.0
367.0
35.0
ADS7854IRTER
WQFN
RTE
16
3000
367.0
367.0
35.0
ADS7854IRTET
WQFN
RTE
16
250
210.0
185.0
35.0
ADS8354IPWR
TSSOP
PW
16
2000
367.0
367.0
35.0
ADS8354IRTER
WQFN
RTE
16
3000
367.0
367.0
35.0
ADS8354IRTET
WQFN
RTE
16
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated