Fairchild FSL176MRT Green-mode fairchild power switch (fpsâ ¢) Datasheet

FSL176MRT
Green-Mode Fairchild Power Switch (FPS™)
Features
Description
 Advanced Soft Burst-Mode Operation for
The FSL176MRT is an integrated Pulse Width
Modulation (PWM) controller and SenseFET specifically
designed for offline Switched-Mode Power Supplies
(SMPS) with minimal external components. The PWM
controller includes an integrated fixed-frequency
oscillator, Under-Voltage Lockout (UVLO), LeadingEdge Blanking (LEB), optimized gate driver, internal
soft-start, temperature-compensated precise current
sources for loop compensation, and self-protection
circuitry. Compared with a discrete MOSFET and PWM
controller solution, the FSL176MRT can reduce total
cost, component count, size, and weight; while
simultaneously increasing efficiency, productivity, and
system reliability. This device provides a basic platform
for cost-effective design of a flyback converter.
Low Standby Power and Low Audible Noise
 Random Frequency Fluctuation for Low EMI
 Pulse-by-Pulse Current Limit
 Various Protection Functions: Overload Protection
(OLP), Over-Voltage Protection (OVP), Abnormal
Over-Current Protection (AOCP), Internal Thermal
Shutdown (TSD) with Hysteresis, Output-Short
Protection (OSP), and Under-Voltage Lockout (UVLO)
with Hysteresis
 Low Operating Current (0.4mA) in Burst Mode
 Internal Startup Circuit
 Internal High-Voltage SenseFET: 650V
 Built-in Soft-Start: 15ms
 Auto-Restart Mode
Applications
 Power Supply for LCD Monitor, STB, and
DVD Combination
Ordering Information
(2)
Output Power Table
Part Number
Package
Operating
Current RDS(ON)
Junction
Limit (Max.)
Temperature
TO-220
6-Lead(1)
FSL176MRTUDTU
UForming
-40°C ~
+125°C
3.50A
1.6Ω
230VAC ±15%(3)
Adapter(4)
80W
85~265VAC
Open
Open
(4)
(5) Adapter
(5)
Frame
Frame
90W
48W
70W
Replaces
Device
FSGM0765R
Notes:
1. Pb-free package per JEDEC J-STD-020B.
2. The junction temperature can limit the maximum output power.
3. 230VAC or 100/115VAC with voltage doubler.
4. Typical continuous power in a non-ventilated enclosed adapter measured at 50C ambient temperature.
5. Maximum practical continuous power in an open-frame design at 50C ambient temperature.
© 2012 Fairchild Semiconductor Corporation
FSL176MRT • Rev. 1.0.0
www.fairchildsemi.com
FSL176MRT — Green-Mode Fairchild Power Switch (FPS™)
August 2012
FSL176MRT — Green-Mode Fairchild Power Switch (FPS™)
Application Circuit
VO
AC
IN
VSTR
Drain
GND
FB
VCC
Figure 1.
Typical Application Circuit
Internal Block Diagram
VSTR
VCC
Drain
6
3
1
ICH
VBURST
0.30V / 0.45V
Vref
Soft Burst
VCC Good
7.5V / 12V
Random
VCC
Vref
2.0µA
IDELAY
FB
OSC
90µA
IFB
Soft-Start
PWM
4
S
Q
R
Q
Gate
Driver
3R
R
N.C.
LEB (300ns)
5
tON<tOSP(1.0μs)
LPF
VAOCP
2
GND
VOSP
VSD
TSD
7.0V
VCC Good
S
Q
R
Q
VCC
VOVP
24.5V
Figure 2.
© 2012 Fairchild Semiconductor Corporation
FSL176MRT • Rev. 1.0.0
Internal Block Diagram
www.fairchildsemi.com
2
Figure 3.
Pin Configuration (Top View)
Pin Definitions
Pin #
Name
1
Drain
SenseFET Drain. High-voltage power SenseFET drain connection.
2
GND
Ground. This pin is the control ground and the SenseFET source.
3
VCC
Power Supply. This pin is the positive supply input, which provides the internal operating
current for both startup and steady-state operation.
4
FB
Feedback. This pin is internally connected to the inverting input of the PWM comparator.
The collector of an opto-coupler is typically tied to this pin. For stable operation, a capacitor
should be placed between this pin and GND. If the voltage of this pin reaches 7V, the overload
protection triggers, which shuts down the FPS.
5
NC
No Connection
VSTR
Startup. This pin is connected directly, or through a resistor, to the high-voltage DC link.
At startup, the internal high-voltage current source supplies internal bias and charges the
external capacitor connected to the VCC pin. Once VCC reaches 12V, the internal current
source (ICH) is disabled.
6
Description
© 2012 Fairchild Semiconductor Corporation
FSL176MRT • Rev. 1.0.0
FSL176MRT — Green-Mode Fairchild Power Switch (FPS™)
Pin Configuration
www.fairchildsemi.com
3
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability.
The absolute maximum ratings are stress ratings only.
Symbol
Parameter
Min.
Max.
Unit
VSTR
VSTR Pin Voltage
650
V
VDS
Drain Pin Voltage
650
V
VCC
VCC Pin Voltage
VFB
Feedback Pin Voltage
IDM
Drain Current Pulsed
IDS
Continuous Switching Drain Current(6)
EAS
PD
TJ
TSTG
ESD
26
V
12.0
V
12.8
A
TC=25C
6.4
A
TC=100C
4.0
A
390
mJ
-0.3
(7)
Single Pulsed Avalanche Energy
Total Power Dissipation (TC=25C)
(8)
Maximum Junction Temperature
50
W
150
C
Operating Junction Temperature(9)
-40
+125
C
Storage Temperature
-55
+150
C
Electrostatic
Discharge Capability
Human Body Model, JESD22-A114
4.5
Charged Device Model, JESD22-C101
2.0
kV
Notes:
6. Repetitive peak switching current when the inductive load is assumed: Limited by maximum duty (DMAX=0.74)
and junction temperature (see Figure 4. ).
7. L=45mH, starting TJ=25C.
8. Infinite cooling condition (refer to the SEMI G30-88).
9. Although this parameter guarantees IC operation, it does not guarantee all electrical characteristics.
Figure 4.
FSL176MRT — Green-Mode Fairchild Power Switch (FPS™)
Absolute Maximum Ratings
Repetitive Peak Switching Current
Thermal Impedance
TA=25°C unless otherwise specified.
Symbol
Parameter
(10)
Value
Unit
θJA
Junction-to-Ambient Thermal Impedance
63.5
°C/W
θJC
Junction-to-Case Thermal Impedance(11)
2.5
°C/W
Notes:
10. Free standing without heat sink under natural convection condition, per JEDEC 51-2 and 1-10.
11. Infinite cooling condition per Mil Std. 883C method 1012.1.
© 2012 Fairchild Semiconductor Corporation
FSL176MRT • Rev. 1.0.0
www.fairchildsemi.com
4
TJ = 25C unless otherwise specified.
Symbol
Parameter
Conditions
Min.
650
Typ.
Max.
Unit
SenseFET Section
BVDSS
Drain-Source Breakdown Voltage
VCC = 0V, ID = 250A
IDSS
Zero-Gate-Voltage Drain Current
VDS = 520V, TA = 125C
RDS(ON)
V
250
1.6
A
Drain-Source On-State Resistance
VGS=10V, ID =1A
1.3
CISS
Input Capacitance(12)
VDS = 25V, VGS = 0V, f=1MHz
674
pF
Ω
COSS
Output Capacitance(12)
VDS = 25V, VGS = 0V, f=1MHz
93
pF
tr
Rise Time
VDS = 325V, ID = 4A, RG=25Ω
30
ns
tf
Fall Time
VDS = 325V, ID = 4A, RG=25Ω
26
ns
td(on)
Turn-On Delay
VDS = 325V, ID = 4A, RG=25Ω
16
ns
td(off)
Turn-Off Delay
VDS = 325V, ID= 4A, RG=25Ω
39
ns
Control Section
fS
fS
Switching Frequency(12)
VCC = 14V, VFB = 4V
(12)
61
67
73
kHz
±5
±10
%
67
73
%
Switching Frequency Variation
-25C < TJ < 125C
DMAX
Maximum Duty Ratio
VCC = 14V, VFB = 4V
DMIN
Minimum Duty Ratio
VCC = 14V, VFB = 0V
Feedback Source Current
VFB=0V
65
90
115
A
VFB = 0V, VCC Sweep
11
12
13
V
After Turn-On, VFB = 0V
7.0
7.5
8.0
IFB
VSTART
VSTOP
tS/S
UVLO Threshold Voltage
Internal Soft-Start Time
61
%
VSTR = 40V, VCC Sweep
15
V
FSL176MRT — Green-Mode Fairchild Power Switch (FPS™)
Electrical Characteristics
ms
Burst-Mode Section
VBURH
VBURL
Burst-Mode Voltage
VCC = 14V, VFB Sweep
0.39
0.45
0.51
V
0.26
0.30
0.34
V
VHys
150
mV
Protection Section
ILIM
Peak Drain Current Limit
VSD
IDELAY
di/dt = 300mA/s
3.15
3.50
3.85
Shutdown Feedback Voltage
VCC = 14V, VFB Sweep
6.45
7.00
7.55
V
Shutdown Delay Current
VCC = 14V, VFB = 4V
1.2
2.0
2.8
A
(12)(14)
tLEB
Leading-Edge Blanking Time
VOVP
Over-Voltage Protection
tOSP
VOSP
tOSP_FB
TSD
THys
Output-Short
Protection(12)
Threshold Time
Threshold VFB
VFB Blanking Time
Thermal Shutdown Temperature(12)
300
VCC Sweep
OSP Triggered when
tON<tOSP & VFB>VOSP
(Lasts Longer than tOSP_FB)
Shutdown Temperature
Hysteresis
A
ns
23.0
24.5
26.0
V
0.7
1.0
1.3
s
1.8
2.0
2.2
V
2.0
2.5
3.0
s
130
140
150
C
60
C
Continued on the following page…
© 2012 Fairchild Semiconductor Corporation
FSL176MRT • Rev. 1.0.0
www.fairchildsemi.com
5
TJ = 25C unless otherwise specified.
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
Total Device Section
IOP
Operating Supply Current,
(Control Part in Burst Mode)
VCC = 14V, VFB = 0V
0.3
0.4
0.5
mA
IOPS
Operating Switching Current,
(Control Part and SenseFET Part)
VCC = 14V, VFB = 2V
1.1
1.5
1.9
mA
Start Current
VCC=11V (Before VCC
Reaches VSTART)
85
120
155
A
Startup Charging Current
VCC = VFB = 0V, VSTR = 40V
0.7
1.0
1.3
mA
Minimum VSTR Supply Voltage
VCC = VFB = 0V, VSTR Sweep
ISTART
ICH
VSTR
26
V
Notes:
12. Although these parameters are guaranteed, they are not 100% tested in production.
13. Average value.
14. tLEB includes gate turn-on time.
Comparison of FSGM0765R and FSL176MRT
Function
FSGM0765R
FSL176MRT
Random Frequency Fluctuation
Operating Current
© 2012 Fairchild Semiconductor Corporation
FSL176MRT • Rev. 1.0.0
1.6mA
Advantages of FSL176MRT
Built-in
Low EMI
0.4mA
Very low standby power
FSL176MRT — Green-Mode Fairchild Power Switch (FPS™)
Electrical Characteristics (Continued)
www.fairchildsemi.com
6
1.20
1.20
1.15
1.15
1.10
1.10
1.05
1.05
Normalized
Normalized
Characteristic graphs are normalized at TA=25°C.
1.00
0.95
0.90
0.85
1.00
0.95
0.90
0.85
0.80
‐40'C ‐20'C
0'C
0.80
‐40'C ‐20'C
25'C 50'C 75'C 90'C 110'C 120'C 125'C
0'C
Temperature [ °C]
Temperature [ °C]
Operating Supply Current (IOP) vs. TA
Figure 6.
1.20
1.20
1.15
1.15
1.10
1.10
1.05
1.05
Normalized
Normalized
Figure 5.
1.00
0.95
0.90
0.85
Operating Switching Current (IOPS) vs. TA
1.00
0.95
0.90
0.85
0.80
‐40'C ‐20'C
0'C
0.80
‐40'C ‐20'C
25'C 50'C 75'C 90'C 110'C 120'C 125'C
0'C
Temperature [ °C]
Startup Charging Current (ICH) vs. TA
Figure 8.
1.40
1.20
1.30
1.15
1.20
1.10
1.10
1.05
1.00
0.90
0.80
0.70
Peak Drain Current Limit (ILIM) vs. TA
1.00
0.95
0.90
0.85
0.60
‐40'C ‐20'C
0'C
0.80
‐40'C ‐20'C
25'C 50'C 75'C 90'C 110'C 120'C 125'C
Temperature [ °C]
Figure 9.
25'C 50'C 75'C 90'C 110'C 120'C 125'C
Temperature [ °C]
Normalized
Normalized
Figure 7.
25'C 50'C 75'C 90'C 110'C 120'C 125'C
FSL176MRT — Green-Mode Fairchild Power Switch (FPS™)
Typical Performance Characteristics
25'C 50'C 75'C 90'C 110'C 120'C 125'C
Temperature [ °C]
Feedback Source Current (IFB) vs. TA
© 2012 Fairchild Semiconductor Corporation
FSL176MRT • Rev. 1.0.0
0'C
Figure 10. Shutdown Delay Current (IDELAY) vs. TA
www.fairchildsemi.com
7
1.20
1.20
1.15
1.15
1.10
1.10
1.05
1.05
Normalized
Normalized
Characteristic graphs are normalized at TA=25°C.
1.00
0.95
0.90
0.85
0.80
‐40'C ‐20'C
1.00
0.95
0.90
0.85
0'C
0.80
‐40'C ‐20'C
25'C 50'C 75'C 90'C 110'C 120'C 125'C
0'C
Temperature [ °C]
Temperature [ °C]
Figure 12. UVLO Threshold Voltage (VSTOP) vs. TA
1.20
1.20
1.15
1.15
1.10
1.10
1.05
1.05
Normalized
Normalized
Figure 11. UVLO Threshold Voltage (VSTART) vs. TA
1.00
0.95
0.90
1.00
0.95
0.90
0.85
0.85
0.80
‐40'C ‐20'C
0'C
0.80
‐40'C ‐20'C
25'C 50'C 75'C 90'C 110'C 120'C 125'C
0'C
Figure 13. Shutdown Feedback Voltage (VSD) vs. TA
Figure 14. Over-Voltage Protection (VOVP) vs. TA
1.20
1.20
1.15
1.15
1.10
1.10
1.05
1.05
Normalized
Normalized
25'C 50'C 75'C 90'C 110'C 120'C 125'C
Temperature [ °C]
Temperature [ °C]
1.00
0.95
0.90
0.85
0.80
‐40'C ‐20'C
25'C 50'C 75'C 90'C 110'C 120'C 125'C
FSL176MRT — Green-Mode Fairchild Power Switch (FPS™)
Typical Performance Characteristics
1.00
0.95
0.90
0.85
0'C
0.80
‐40'C ‐20'C
25'C 50'C 75'C 90'C 110'C 120'C 125'C
Temperature [ °C]
25'C 50'C 75'C 90'C 110'C 120'C 125'C
Temperature [ °C]
Figure 15. Switching Frequency (fS) vs. TA
© 2012 Fairchild Semiconductor Corporation
FSL176MRT • Rev. 1.0.0
0'C
Figure 16. Maximum Duty Ratio (DMAX) vs. TA
www.fairchildsemi.com
8
3. Feedback Control: This device employs currentmode control, as shown in Figure 18. An opto-coupler
(such as the FOD817) and shunt regulator (such as the
KA431) are typically used to implement the feedback
network. Comparing the feedback voltage with the
voltage across the RSENSE resistor makes it possible to
control the switching duty cycle. When the reference pin
voltage of the shunt regulator exceeds the internal
reference voltage of 2.5V, the opto-coupler LED current
increases, pulling down the feedback voltage and
reducing drain current. This typically occurs when the
input voltage is increased or the output load is decreased.
1. Startup: At startup, an internal high-voltage current
source supplies the internal bias and charges the
external capacitor (CVcc) connected to the VCC pin, as
illustrated in Figure 17. When VCC reaches 12V, the
FSL176MRT begins switching and the internal highvoltage current source is disabled. The FSL176MRT
continues normal switching operation and the power is
supplied from the auxiliary transformer winding unless
VCC goes below the stop voltage of 7.5V.
3.1 Pulse-by-Pulse Current Limit: Because currentmode control is employed, the peak current through
the SenseFET is limited by the inverting input of the
PWM comparator (VFB*), as shown in Figure 18.
Assuming that the 90μA current source flows only
through the internal resistor (3R + R = 27kΩ), the
cathode voltage of diode D2 is about 2.5V. Since D1 is
blocked when the feedback voltage (VFB) exceeds
2.5V, the maximum voltage of the cathode of D2 is
clamped at this voltage. Therefore, the peak value of
the current through the SenseFET is limited.
Figure 17. Startup Block
3.2 Leading-Edge Blanking (LEB): At the instant the
internal SenseFET is turned on, a high-current spike
usually occurs through the SenseFET, caused by
primary-side capacitance and secondary-side rectifier
reverse recovery. Excessive voltage across the RSENSE
resistor leads to incorrect feedback operation in the
current-mode PWM control. To counter this effect, the
FSL176MRT employs a leading-edge blanking (LEB)
circuit. This circuit inhibits the PWM comparator for
tLEB (300ns) after the SenseFET is turned on.
2. Soft-Start: The internal soft-start circuit increases the
PWM comparator inverting input voltage, together with
the SenseFET current, slowly after startup. The typical
soft-start time is 15ms. The pulse width to the power
switching device is progressively increased to establish
the correct working conditions for transformers,
inductors, and capacitors. The voltage on the output
capacitors is progressively increased to smoothly
establish the required output voltage. This helps prevent
transformer saturation and reduces stress on the
secondary diode during startup.
FSL176MRT — Green-Mode Fairchild Power Switch (FPS™)
Functional Description
Figure 18. Pulse Width Modulation Circuit
© 2012 Fairchild Semiconductor Corporation
FSL176MRT • Rev. 1.0.0
www.fairchildsemi.com
9
B
B
Figure 20. Overload Protection
4.2 Abnormal Over-Current Protection (AOCP):
When the secondary rectifier diodes or the
transformer pins are shorted, a steep current with
extremely high di/dt can flow through the SenseFET
during the minimum turn-on time. Overload protection
is not enough to protect the FSL176MRT in that
abnormal case; since severe current stress is
imposed on the SenseFET until OLP is triggered. The
FSL176MRT internal AOCP circuit is shown in Figure
21. When the gate turn-on signal is applied to the
power SenseFET, the AOCP block is enabled and
monitors the current through the sensing resistor. The
voltage across the resistor is compared with a preset
AOCP level. If the sensing resistor voltage is greater
than the AOCP level, the set signal is applied to the
S-R latch, resulting in the shutdown of the SMPS.
FSL176MRT — Green-Mode Fairchild Power Switch (FPS™)
7.0V, when the switching operation is terminated, as
shown in Figure 20. The delay for shutdown is the
time required to charge CFB from 2.5V to 7.0V with
2.0µA. A 25 ~ 50ms delay is typical. This protection is
implemented in auto-restart mode.
4. Protection Circuits: The FSL176MRT has several
self-protective functions, such as Overload Protection
(OLP), Abnormal Over-Current Protection (AOCP),
Output-Short Protection (OSP), Over-Voltage Protection
(OVP), and Thermal Shutdown (TSD). All the
protections are implemented as auto-restart. Once a
fault condition is detected, switching is terminated and
the SenseFET remains off. This causes VCC to fall.
When VCC falls to the Under-Voltage Lockout (UVLO)
stop voltage of 7.5V, the protection is reset and the
startup circuit charges the VCC capacitor. When VCC
reaches the start voltage of 12.0V, the FSL176MRT
resumes normal operation. If the fault condition is not
removed, the SenseFET remains off and VCC drops to
stop voltage again. In this manner, the auto-restart can
alternately enable and disable the switching of the
power SenseFET until the fault condition is eliminated.
Because these protection circuits are fully integrated
into the IC without external components, the reliability is
improved without increasing cost.
Figure 19. Auto-Restart Protection Waveforms
4.1 Overload Protection (OLP): Overload is defined
as the load current exceeding its normal level due to
an unexpected abnormal event. In this situation, the
protection circuit should trigger to protect the SMPS.
However, when the SMPS is in normal operation, the
overload protection circuit can be triggered during
load transition. To avoid this undesired operation, the
overload protection circuit is designed to trigger only
after a specified time to determine whether it is a
transient situation or a true overload situation.
Because of the pulse-by-pulse current-limit capability,
the maximum peak current through the SenseFET is
limited and, therefore, the maximum input power is
restricted with a given input voltage. If the output
consumes more than this maximum power, the output
voltage (VOUT) decreases below the set voltage. This
reduces the current through the opto-coupler LED,
which also reduces the opto-coupler transistor
current, thus increasing the feedback voltage (VFB). If
VFB exceeds 2.5V, D1 is blocked and the 2.0µA
current source starts to charge CFB slowly up. In this
condition, VFB continues increasing until it reaches
© 2012 Fairchild Semiconductor Corporation
FSL176MRT • Rev. 1.0.0
Figure 21. Abnormal Over-Current Protection
www.fairchildsemi.com
10
Figure 22. Output-Short Protection
4.4 Over-Voltage Protection (OVP): If the
secondary-side feedback circuit malfunctions or a
solder defect causes an opening in the feedback path,
the current through the opto-coupler transistor
becomes almost zero. Then VFB climbs up in a similar
manner to the overload situation, forcing the preset
maximum current to be supplied to the SMPS until the
overload protection is triggered. Because more energy
than required is provided to the output, the output
voltage may exceed the rated voltage before the
overload protection is triggered, resulting in the
breakdown of the devices in the secondary side. To
prevent this situation, an OVP circuit is employed. In
general, the VCC is proportional to the output voltage
and the FSL176MRT uses VCC instead of directly
monitoring the output voltage. If VCC exceeds 24.5V,
an OVP circuit is triggered, resulting in the termination
of the switching operation. To avoid undesired
activation of OVP during normal operation, VCC should
be designed to be below 24.5V.
FSL176MRT — Green-Mode Fairchild Power Switch (FPS™)
5. Soft Burst-Mode Operation: To minimize power
dissipation in Standby Mode, the FSL176MRT enters
Burst-Mode operation. As the load decreases, the
feedback voltage decreases. The device automatically
enters Burst Mode when the feedback voltage drops
below VBURL (300mV), as shown in Figure 23. At this
point, switching stops and the output voltages start to
drop at a rate dependent on standby current load. This
causes the feedback voltage to rise. Once it passes
VBURH (450mV), switching resumes. The feedback
voltage then falls and the process repeats. Burst Mode
alternately enables and disables switching of the
SenseFET, reducing switching loss in Standby Mode.
4.3. Output-Short Protection (OSP): If the output is
shorted, steep current with extremely high di/dt can
flow through the SenseFET during the minimum turnon time. Such a steep current brings high-voltage
stress on the drain of the SenseFET when turned off.
To protect the device from this abnormal condition,
OSP is included. It is comprised of detecting VFB and
SenseFET turn-on time. When the VFB is higher than
2.0V and the SenseFET turn-on time is lower than
1.0μs, the FSL176MRT recognizes this condition as
an abnormal error and shuts down PWM switching
until VCC reaches VSTART again. An abnormal condition
output short is shown in Figure 22.
Figure 23. Burst-Mode Operation
6. Random Frequency Fluctuation (RFF): Fluctuating
switching frequency of an SMPS can reduce EMI by
spreading the energy over a wide frequency range. The
amount of EMI reduction is directly related to the
switching frequency variation, which is limited internally.
The switching frequency is determined randomly by the
external feedback voltage and an internal free-running
oscillator at every switching instant. This random
frequency fluctuation scatters the EMI noise around
typical switching frequency (67kHz) effectively and can
reduce the cost of the input filter included to meet the
EMI requirements (e.g. EN55022).
4.5 Thermal Shutdown (TSD): The SenseFET and
the control IC on a die in one package makes it easier
for the control IC to detect high temperature of the
SenseFET. If the temperature exceeds ~140C, the
thermal shutdown is triggered and stops operation.
The FSL176MRT operates in auto-restart mode until
the temperature decreases to around 75C, when
normal operation resumes.
Figure 24. Random Frequency Fluctuation
© 2012 Fairchild Semiconductor Corporation
FSL176MRT • Rev. 1.0.0
www.fairchildsemi.com
11
Application
LCD Monitor
Power Supply
Input Voltage
Rated Output
5.0V (3A)
85 ~ 265VAC
14.0V (3.5A)
Rated Power
64W
Key Design Notes:
1.
The delay for overload protection (OLP) is designed to be about 30ms with C105 (8.2nF). OLP time between
39ms (12nF) and 46ms (15nF) is recommended.
2.
The SMD-type capacitor (C106) must be placed as close as possible to the VCC pin to avoid malfunction by
abrupt pulsating noises and to improve ESD and surge immunity. Capacitance between 100nF and 220nF
is recommended.
FSL176MRT — Green-Mode Fairchild Power Switch (FPS™)
Typical Application Circuit
Figure 25. Schematic
© 2012 Fairchild Semiconductor Corporation
FSL176MRT • Rev. 1.0.0
www.fairchildsemi.com
12

Core: EER3019 (Ae=134 mm2)

Bobbin: EER3019
Figure 26. Transformer Specification
Table 1.
Winding Specification
Np /2(BOT)
Pin (S → F)
Wire
Turns
Winding Method
3→2
0.4φ×1
18
Barrier Tape
TOP
BOT
Ts
Solenoid Winding
2.0mm
1
3
Solenoid Winding
3.0mm
1
8
Solenoid Winding
3.0mm
1
3
Solenoid Winding
3.0mm
1
5
Solenoid Winding
18
Solenoid Winding
Insulation: Polyester Tape t = 0.025mm, 2 Layers
N5V
7→6
0.4φ×3 (TIW)
FSL176MRT — Green-Mode Fairchild Power Switch (FPS™)
Transformer Specification
Insulation: Polyester Tape t = 0.025mm, 2 Layers
Na
4→5
0.20φ×1
4.0mm
Insulation: Polyester Tape t = 0.025mm, 2 Layers
N5V
8→6
0.4φ×3 (TIW)
Insulation: Polyester Tape t = 0.025mm, 2 Layers
N14V
10 → 8
0.4φ×3 (TIW)
1
Insulation: Polyester Tape t = 0.025mm, 2 Layers
Np/2(TOP)
2→1
0.4φ×1
2.0mm
1
Insulation: Polyester Tape t = 0.025mm, 2 Layers
Table 2.
Electrical Characteristics
Pin
Specification
Remark
Inductance
1-3
465H ±6%
67kHz, 1V
Leakage
1-3
10H Maximum
Short all other pins
© 2012 Fairchild Semiconductor Corporation
FSL176MRT • Rev. 1.0.0
www.fairchildsemi.com
13
Bill of Materials
Part #
Value
F101
250V 3.15A
Note
Part #
Value
C101
220nF / 275V
Box (Pilkor)
C102
150nF/275V
Box (Pilkor)
C103
120µF / 400V
Electrolytic (SamYoung)
C104
3.3nF/630V
Film (Sehwa)
Fuse
Capacitor
NTC
NTC101
5D-11
Note
DSC
Resistor
R101
1.5MΩ, J
1W
C105
12nF / 100V
Film (Sehwa)
R103
43kΩ, J
1W
C106
220nF
SMD (2012)
R201
1kΩ, F
1/4W, 1%
C107
47µF / 50V
Electrolytic (SamYoung)
R202
1.2kΩ, F
1/4W, 1%
C201
1000µF / 25V
Electrolytic (SamYoung)
R203
18kΩ, F
1/4W, 1%
C202
1000µF / 25V
Electrolytic (SamYoung)
R204
8kΩ, F
1/4W, 1%
C203
1000µF / 25V
Electrolytic (SamYoung)
R205
8kΩ, F
1/4W, 1%
C204
2200µF / 10V
Electrolytic (SamYoung)
C205
1000µF / 16V
Electrolytic (SamYoung)
C206
1000µF / 16V
Electrolytic (SamYoung)
C207
100nF
SMD (2012)
C208
100nF
SMD (2012)
C301
4.7nF / Y2
Y-cap (Samhwa)
LF101
20mH
Line Filter 0.5Ø
L201
5µH
5A Rating
L202
5µH
5A Rating
IC
SMPS
FSL176MRT
Fairchild Semiconductor
IC201
KA431LZ
Fairchild Semiconductor
IC301
FOD817B
Fairchild Semiconductor
Inductor
Diode
D101
1N4007
Vishay
D102
UF4004
Vishay
ZD101
1N4750
Vishay
D201
MBR20150CT
Fairchild Semiconductor
D202
FYPF2006DN
Fairchild Semiconductor
BD101
G3SBA60
Vishay
© 2012 Fairchild Semiconductor Corporation
FSL176MRT • Rev. 1.0.0
FSL176MRT — Green-Mode Fairchild Power Switch (FPS™)
Table 3.
Transformer
T101
465µH
www.fairchildsemi.com
14
10.36
9.96
B
2.74
2.34
(7.00)
A
(0.70)
Ø3.28
3.08
5.18
4.98
3.40
3.20
(5.40)
6.88
6.48
16.07
15.67
19.97 18.94
18.97 17.94
13.05
R0.55
8.13
7.13
R0.55
R0.55
(0.88)
1.40
1.20
0.80 5PLCS
0.70
#1
3.06
2.46
#6
24.00
23.00
(0.48)
#1,6
#2,4
7.15
#3,5
0.70 5PLCS
0.50
2.19
0.60
0.45
1.75
1.27
FSL176MRT — Green-Mode Fairchild Power Switch (FPS™)
Physical Dimensions
0.20
3.48
2.88
A B
(3.81)
3.81
7.29
6.69
5°
5°
NOTES:
A) NO PACKAGE STANDARD APPLIES.
B) DIMENSIONS ARE EXCLUSIVE OF BURRS,
MOLD FLASH, AND TIE BAR EXTRUSIONS.
C) DIMENSIONS ARE IN MILLIMETERS.
D) DRAWING FILENAME : MKT-TO220F06REV2
4.80
4.40
Figure 28. 6-Lead, TO220, Fullpack, U-Forming, 2 DAP
Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner
without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or
obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the
warranty therein, which covers Fairchild products.
Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:
http://www.fairchildsemi.com/packaging/.
© 2012 Fairchild Semiconductor Corporation
FSL176MRT • Rev. 1.0.0
www.fairchildsemi.com
15
FSL176MRT — Green-Mode Fairchild Power Switch (FPS™)
© 2012 Fairchild Semiconductor Corporation
FSL176MRT • Rev. 1.0.0
www.fairchildsemi.com
16
Similar pages