Littelfuse LSP05120 Led lighting surge protection module > lsp05 Datasheet

Surge Protection Module
LED Lighting Surge Protection Module > LSP05
LSP05 Module Series
RoHS
Description
The Littelfuse LSP05 thermally protected Surge Protective
Device is a self-protected device which is specially designed
to be used in outdoor and commercial LED lighting fixtures
for transient overvoltage protection. It is constructed with
Littelfuse thermally protected varistor technology. Its built-in
thermal disconnect function provides additional protection
to prevent catastrophic failure and fire hazard even under the
extreme circumstances of varistor end-of-life or sustaining
over voltage conditions. The LSP05 facilitates customer’s
product compliance to IEEE C62.41.2 Location Category C
Low and US Dept of Energy MSSLC Model Spec.
Agency Approvals
Standard
Agency File Number
UL1449
E320116
Applications
• Outdoor and Commercial
LED Lighting
• Roadway lighting
• Traffic lighting
• Digital signage
•
•
•
•
•
Wash wall lighting
Parking garage/lot lighting
Flood lighting
Tunnel lighting
Street lighting
Additional Information
Datasheet
Resources
Samples
• Maximum Discharge
Current, 10kA, 8/20us
• Meets ANSI C82.775-2015: Location
Category CM, 10kV/5kA,
1.2/50µS-8/20µS
Combination Wave.
• Meets IEEE C62.41.2:
Location Category CLow,
6kV/3kA, 1.2/50µS-8/20µS
Combination Wave.
• Meets US Dept.
of Energy MSSLC
Model Spec.
• Parallel connected
SPD device
• Thermally protected
Varistor technology
• IP66 Water-proof
and Dust-proof
• Indication wire lead
options for Parallel
connected modules
• UL 1449 Type 4
Component Assembly
Recognition (Type 4CA)
• IEC61643-11 Class II/
EN61643-11 Type
2 Compliant1
• Compact form factor
(48x48x30mm) with
mounting tabs
• 240Vac and 277Vac
voltage ratings are
available for Class I
and Class II installation
based on IEC luminaire
protection classes
• CE - Meets the
requirements of Low
Voltage and RoHS
European Directives.
LV UltraMOV™ Series
Agency
Features
Notes:
1. Self-declared compliance.
Absolute Maximum Ratings
• For ratings of individual members of a series, see Device Ratings and Specifications chart
LSP05 Series
Units
150 to 510
V
Continous:
Steady State Applied Voltage:
Max AC Voltage Range (VM(AC)RMS)
Transient:
Maximum Discharge Current 8/20μs Waveform (Imax)
10,000
A
Nominal Discharge Current 8/20µs Waveform (In)
5,000
A
Operating Ambient Temperature Range (TA)
-45 to +85
°C
Storage Temperature Range (TSTG)
-45 to +125
°C
Isolation Voltage Capability (When the thermal disconnect opens)
Insulation Resistance
600
V
>1,000
MΩ
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of
the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 05/09/16
1
Surge Protection Module
LED Lighting Surge Protection Module > LSP05
LSP05 Series Device Ratings & Specifications
Operating
Voltage
(VAC)
MCOV/Uc
(VAC)5
Maximum
Discharge
Current
(Imax)(A)2
Nominal
Discharge
Current
(In)(A)1
LSP05120*
120
150
10,000
5,000
LSP05240*
240
275
10,000
5,000
LSP05277*
277
320
10,000
5,000
LSP05347*
347
420
10,000
5,000
LSP05480*
480
510
10,000
5,000
L-L:240
L-L:275
L-N/G:120
L-N/G:150
10,000
5,000
L-L:480
L-L:510
L-N/G:277
L-N/G:320
Part Number7
LSP05240LL*
LSP05480LL*
10,000
5,000
MLV
(V)3
Up
(V)4
L-N:680
L-G:680
N-G:630
L-N:1100
L-G:1100
N-G:1100
L-N:1270
L-G:1270
N-G:1220
L-N:1600
L-G:1600
N-G:1580
L-N:1780
L-G:1780
N-G:1730
Safety Compliance
IEC/EN 61643-116
800
UL1449
X
1200
X
X
1400
X
X
1700
X
1900
X
L-L:1100
L-L:1200
X
L-N/G:680
L-N/G:800
X
L-L:1780
L-L:1900
X
L-N/G:1270
L-N/G:1400
X
Notes:
1. Nominal Discharge Current (In)(A): The nominal discharge current is a measure of the SPDs endurance capability; 15 impulses of discharge current uses the 8/20us current waveform.
2. Maximum Discharge Current (Imax)(A): The maximum discharge current is a measure of the SPDs maximum capability; single impulse of discharge current uses the 8/20us current
waveform.
3. MLV – UL1449 Measured limiting voltage; the highest value of residual voltage measurements during the application of impulses of 8/20us nominal discharge current (In); an average
voltage value of 15 impulses
4. Up – IEC 61643-11 Voltage protection level; the highest value of residual voltage measurements during the application of impulses of 8/20us nominal discharge current (In); a
rounding voltage value of maximum measurement.
5. MCOV/UC: Maximum Continuous Operating Voltage - maximum r.m.s. voltage that could be continuously applied to the SPD.
6. Part Numbers LSP05xxxPM Only.
7. * = - P or PM
8. Repetitive Surge Withstanding: 15 strikes at 5,000A (8/20us) with steady MLV/Up.
Repetitive Surge Capability for LSP05
Pulse Rating
(8x20µSec)
Strikes
Surge
1
10,000A
2
7,000A
15
5,000A
100
1,500A
1,000
700A
Figure 1
2
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 05/09/16
Surge Protection Module
LED Lighting Surge Protection Module > LSP05
Typical Dimensions (mm)
Application/Installation Schematic
Dimensions 56.0 ±0.5
Typical Dimensions (mm)
L
L
L
N
N
56.0 ±0.5
L
48.0±1.5
or
N/G
AC/DC
Power
Supply
G
+
-
LED Module
2x ø4.8±0.2
48.0±1.5
2x ø4.8±0.2
100 ±20
3 indication wires
all use the AWG22.
100 ±20
48.0 ±1.5
100 ±20
100 ±20
48.0 ±1.5
3 indication wires
all use the AWG22.
30.0 ±1.0
2.3 ±0.2
6 ±2
30.0 ±1.0
6 ±2
2.3 ±0.2 64.0 ±1.5
6 ±2
6 ±2
64.0 ±1.5
Parallel Connection
With LED indicating SPD status
- ON (green): SPD is online
- OFF: SPD needs replacement
L
L
or
N/G
R1
R2
R3
SPD
NC
LED normally on
LSP05xxxPM
L
L
N
N
R
AC/DC
Power
Supply
G
+
-
LED Module
R1
Parallel Connection
SPD
LED normally off
R2
R3
With LED indicating SPD status
LSP05xxxPM
- OFF: SPD is online
- ON (red): SPD needs replacement
R
L
L
LSP05XXXXXP
N/G
LSP05XXXXXP
or
L
L
N
N
LV UltraMOV™ Series
Notes:
1. LED indicator and associated circuitry are not included in the module.
2. R1 must be capped off by wire nut when not connected (NC).
3. R1 and R2 are AC line voltage (hot); R3 is AC neutral voltage.
4. R2 voltage is cut off when SPD needs replacement.
5. R is current limiting resistor; it resistance/wattage is determined by AC line voltage
and desired current driving LED. Example: AC line voltage 240V, LED: 1.6mA, resistor:
150Kohm/0.5W.
AC/DC
Power
+
Supply
-
LED Module
G
LSP05XXXXXPM
LSP05XXXXXPM
Notes:
1. Black: Line; White: Neutral; Green: Ground
(P/N with suffix X3333/X3316: Brown: Line; Blue: Neutral; Green-Yellow stripe: Ground)
2. Black: R1; Red: R2; Blue: R3
3. Wire Gauge: AWG14 wire Line in, AWG22 Wire for indication; Wire Length: 100mm or
customized
Part Numbering System
LSP 05 480LL P Xxxxx
Device Family
Parallel Connection
SPD
L
L
N
N
AC/DC
Power
Supply
G
+
-
LED Module
Littelfuse Surge Protection Module
Nominal Discharge
Current (In)
Operating Voltage
Connection mode
Parallel Connection
(for Class II Unearthed)
SPD
~X3316
LL: for L,L,N/G
Blank: L-N, L-G, N-G
P or PM
(P: parallel connection; PM: parallel
connection and with monitor indication wire)
Other non-standard option:
X3333: with GND wire connection, available for
240Vac and 277Vac rating with CE Marking for
Class I earthed installation
Wire Color: Line: Brown, Neutral: Blue, Ground/P:
Green with yellow stripe
© 2016 Littelfuse,
3316:Inc.
without GND wire connection option
Specifications
are Color:
subjectLine:
to change
without
notice.
Wire
Brown,
Neutral:
Blue
Revised: 05/09/16
3
Similar pages