TI1 ADS7815U/1K Analog-to-digital converter Datasheet

ADS7815
ADS
781
5
SBAS065B – DECEMBER 1996 – DECEMBER 2006
16-Bit 250kHz Sampling CMOS
ANALOG-to-DIGITAL CONVERTER
FEATURES
DESCRIPTION
●
●
●
●
●
●
The ADS7815 is a complete 16-bit sampling analog-todigital (A/D) converter featuring excellent AC
performance and a 250kHz throughput rate. The design
includes a 16-bit capacitor-based SAR A/D
converter with an inherent sample and hold (S/H), a precision reference, and an internal clock. Spurious-free dynamic
range with a 100kHz full-scale sinewave input is typically
greater than 100dB. The ±2.5V input range allows development of precision systems using only ±5V supplies. The
converter is available in a 28-lead SOIC package specified
for operation over the industrial –25°C to +85°C temperature range.
250kHz SAMPLING RATE
COMPLETE WITH S/H, REF, CLOCK, ETC.
96dB min SFDR WITH 100kHz INPUT
82dB min SINAD WITH 100kHz INPUT
±2.5V INPUT RANGE
28-LEAD SOIC
APPLICATIONS
●
●
●
●
WIRELESS BASE STATIONS
SPECTRUM ANALYSIS
IMAGING SYSTEMS
DATA ACQUISITION
R/C
Clock
Successive Approximation Register and Control Logic
CS
BUSY
CDAC
Output
±2.5V Input
Latches
and
Comparator
Three
Parallel
Data
Bus
State
Drivers
Buffer
5kΩ
REF Out/In
Internal
+2.5V Ref
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
Copyright © 1996-2006, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
www.ti.com
ELECTROSTATIC
DISCHARGE SENSITIVITY
ABSOLUTE MAXIMUM RATINGS
Analog Inputs: VIN ................................................................................ ±VS
REF ............................................ GND –0.3V to +VS +0.3V
CAP ............................................... Indefinite Short to GND
Momentary Short to +VS
+VS ......................................................................................................... 7V
–VS ...................................................................................................... –7V
Digital Inputs ...................................................... GND –0.3V to +VS +0.3V
Maximum Junction Temperature ................................................... +165°C
Internal Power Dissipation ............................................................. 825mW
Lead Temperature (soldering, 10s) ............................................... +300°C
PACKAGE/ORDERING INFORMATION(1)
PRODUCT
PACKAGE
PACKAGE
DESIGNATOR
TEMPERATURE
RANGE
ADS7815U
28-Pin SOIC
DW
–25°C to +85°C
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may be
more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
NOTE: (1) For the most current package and ordering information, see the
Package Option Addendum at then end of this data sheet, or see the TI website
at www.ti.com.
2
ADS7815
www.ti.com
SBAS065B
ELECTRICAL CHARACTERISTICS
At TA = –25°C to +85°C, fS = 250kHz, +VS = +5V, and –VS = –5V, using internal reference, unless otherwise specified.
ADS7815U
PARAMETER
CONDITIONS
MIN
TYP
RESOLUTION
ANALOG INPUT
Voltage Range
Impedance
Capacitance
THROUGHPUT SPEED
Conversion Cycle
Throughput Rate
DC ACCURACY
Integral Linearity Error
No Missing Codes
Transition Noise(2)
Full Scale Error(3)
Full Scale Error Drift
Bipolar Zero Error
Bipolar Zero Error Drift
Power Supply Sensitivity
AC ACCURACY
Spurious-Free Dynamic Range
Total Harmonic Distortion
Signal-to-(Noise+Distortion)
Signal-to-Noise
Usable Bandwidth(5)
Aperture Delay
REFERENCE
Internal Reference Voltage
Internal Reference Source Current
External Reference Voltage Range
External Reference Current Drain
Output Capacitance
UNITS
16
Bits
±2.5V
100
30
Acquire and Convert
V
MΩ
pF
4.0
250
±4
15
0.8
±0.1
±7
±2
±2
±6
+VS ±5%, –VS ±5%
fIN = 100kHz
fIN = 100kHz
fIN = 100kHz
–60dB Input
fIN = 100kHz
96
100
–98
–94
28
82
1
40
2.45
2.3
2.5
1
2.5
VREF = +2.5V
–0.3
+2.8
µs
kHz
LSB(1)
Bits
LSB
%
ppm/°C
mV
ppm/°C
LSB
82
DIGITAL INPUTS
Logic Levels
VIL
VIH
IIL
IIH
DIGITAL OUTPUTS
Data Format
Data Coding
VOL
VOH
Leakage Current
MAX
2.55
dB(4)
dB
dB
dB
dB
MHz
ns
2.7
100
V
µA
V
µA
+0.8
+VS +0.3V
±10
±10
V
V
µA
µA
+0.4
±5
V
V
µA
15
pF
83
83
ns
ns
+5.25
–4.75
250
V
V
mA
mA
mW
+85
+125
°C
°C
Parallel 16 bits
Binary Two’s Complement
ISINK = 1.6mA
ISOURCE = 200µA
High-Z State,
VOUT = 0V to VDIG
High-Z State
+4
DIGITAL TIMING
Bus Access Time
Bus Relinquish Time
POWER SUPPLIES
+VS
–VS
+IS
–IS
Power Dissipation
+4.75
–5.25
TEMPERATURE RANGE
Specified Performance
Storage
–25
–55
+5
–5
+30
–10
200
NOTES: (1) LSB means Least Significant Bit. For the 16-bit, ±2.5V input ADS7815, one LSB is 76µV.
(2) Typical rms noise at worst case transitions and temperatures.
(3) Full scale error is the worst case of –Full Scale or +Full Scale untrimmed deviation from ideal first and last code transitions, divided by the
transition voltage (not divided by the full-scale range) and includes the effect of offset error.
(4) All specifications in dB are referred to a full-scale ±2.5V input.
(5) Full-Power Bandwidth defined as Full-Scale input frequency at which Signal-to-(Noise+Distortion) degrades to 60dB, or 10 bits of accuracy.
ADS7815
SBAS065B
www.ti.com
3
PIN CONFIGURATION
Top View
SOIC
VIN
1
28 +VS
GND
2
27 +VS
REF
3
26 BUSY
CAP
4
25 CS
GND
5
24 R/C
D15 (MSB)
6
23 –VS
D14
7
22 D0 (LSB)
ADS7815
PIN #
NAME
1
2
3
VIN
GND
REF
4
5
6
CAP
GND
D15 (MSB)
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
D14
D13
D12
D11
D10
D9
D8
GND
D7
D6
D5
D4
D3
D2
D1
D0 (LSB)
23
24
–VS
R/C
25
CS
26
BUSY
27
28
+VS
+VS
D13
8
21 D1
D12
9
20 D2
D11 10
19 D3
D10 11
18 D4
D9 12
17 D5
D8 13
16 D6
GND 14
15 D7
DESCRIPTION
Analog Input. Full-scale input range is ±2.5V.
Ground.
Reference Input/Output. Outputs internal reference of +2.5V nominal. Can also be driven by external system reference. In
both cases, connect to ground with a 0.1µF ceramic capacitor in parallel with 2.2µF tantalum capacitor.
Reference compensation capacitor. Use a parallel combination of a 0.1µF ceramic capacitor and a 2.2µF tantalum capacitor.
Ground.
Data Bit 15. Most Significant Bit (MSB) of conversion results. Hi-Z state when CS is HIGH, when R/C is LOW or when a
conversion is in progress.
Data Bit 14. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress.
Data Bit 13. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress.
Data Bit 12. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress.
Data Bit 11. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress.
Data Bit 10. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress.
Data Bit 9. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress.
Data Bit 8. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress.
Ground.
Data Bit 7. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress.
Data Bit 6. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress.
Data Bit 5. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress.
Data Bit 4. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress.
Data Bit 3. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress.
Data Bit 2. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress.
Data Bit 1. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress.
Data Bit 0. Least Significant Bit (LSB) of conversion results. Hi-Z state when CS is HIGH, when R/C is LOW or when a
conversion is in progress.
Negative supply input. Nominally –5V. Decouple to analog ground with 0.1µF ceramic and 10µF tantalum capacitors.
Read/convert input. With R/C HIGH, CS going LOW will enable the output data bits if a conversion is not in progress. With
R/C LOW, CS going LOW will start a conversion if one is not already in progress.
Chip select. With R/C LOW, CS going LOW will initiate a conversion if one is not already in progress. With R/C HIGH, CS
going LOW will enable the output data bits if a conversion is not in progress.
Busy output. Falls when a conversion is started, and remains LOW until the conversion is completed. With CS LOW and
R/C HIGH, output data will be valid when BUSY rises, so that the rising edge can be used to latch the data. CS or R/C must
be HIGH within 250ns after BUSY rises or another conversion will start without time for signal acquisition.
Positive supply input. Nominally +5V. Connect directly to pin 28.
Positive supply input. Nominally +5V. Connect directly to pin 27. Decouple to ground with 0.1µF ceramic and 10µF
tantalum capacitors.
TABLE I. Pin Assignments.
4
ADS7815
www.ti.com
SBAS065B
BASIC OPERATION
is placed on these outputs. In the circuit shown in Figure 1,
the rising edge of BUSY latches the result into the 74HC574s.
Figure 1 shows the recommended circuit for operation of the
ADS7815. A falling edge on the convert pulse signal places
the sample and hold into the hold mode and initiates a
conversion. When the conversion is complete, the pins D15
through D0 become active and the result of the conversion
After the conversion is complete, the ADS7815 sample and
hold returns to the sample mode and begins acquiring the
input signal for the next conversion. Allowing 4µs between
falling edges of the convert pulse signal assures accurate
acquisition of the analog input.
R1
75Ω
+5V
R2
10Ω
OPA628
–5V
2.2µF
C3
2.2µF
C4
+
+
0.1µF
C5
0.1µF
C6
1
VIN
+VS 28
2
GND
+VS 27
3
REF
BUSY 26
4
CAP
CS 25
5
GND
R/C 24
6
D15
–VS 23
7
8
D14
D0 22
ADS7815
D13
D1 21
9
D12
D2 20
10
D11
D3 19
11
D10
D4 18
2
12
D9
D5 17
3
13
D8
D6 16
4
14
GND
D7 15
5
0.1µF
C1
+
+5V
10µF
C2
Convert Pulse
74HC00
–5V
100ns min
0.1µF
C7
10µF
+ C8
OC
1
10
6
7
8
9
OC
CLK
1D
1Q
2D
2Q
3D
3Q
4D
4Q
5D
5Q
6D
6Q
7D
7Q
8D
8Q
µProcessor
Bus
74HC574
1
10
2
3
4
5
6
7
8
9
OC
CLK
1D
1Q
2D
2Q
3D
3Q
4D
4Q
5D
5Q
6D
6Q
7D
7Q
8D
8Q
µProcessor
Bus
74HC574
FIGURE 1. Basic Operation.
ADS7815
SBAS065B
www.ti.com
5
TIMING
the digital outputs tri-stating while the sample and hold
transitions to the hold mode. The change in digital outputs
results in noise being coupled onto the hold capacitor.
The timing shown in Figure 2 and Table II is the recommended method of operating the ADS7815. The falling edge
of CS initiates the conversion. During the conversion, the
digital outputs are tri-stated and BUSY is LOW. Near the
end of the conversion, the digital outputs become active with
the most recent conversion result. After a brief delay (see
time t11 in Figure 2 and Table II), BUSY rises. The rising
edge of BUSY is used to latch the digital result in Figure 1.
If a conversion is not in progress or is just about to finish, the
digital outputs will be active when R/C is HIGH and CS is
LOW. This is shown in Figure 2 and Figure 3. It is possible
to return CS HIGH during the initial part of the conversion
(as is done with R/C) and prevent the digital outputs from
becoming active. At a later time, the digital results could be
read by taking CS LOW. It is also possible to leave R/C
LOW, take CS HIGH during the conversion, and read the
results at a later time by taking R/C HIGH and CS LOW.
R/C AND CS
The R/C (read/convert) and CS signals control the start of
conversion and, when a conversion is not in progress, the
status of the digital outputs D15 through D0. It is possible to
start a conversion by taking CS LOW and then taking R/C
LOW. However, this is not recommended and will result in
a significant decrease in signal-to-noise ratio. This is due to
SYMBOL
DESCRIPTION
MIN
t1
CS to R/C Delay
t2
CS to BUSY Delay
TYP
MAX
UNITS
200
ns
40
Aperture Delay
40
ns
t4
BUSY LOW
3.3
µs
R/C LOW to CS LOW
t6
BUSY HIGH to CS HIGH
100
t7
Bus Access Time
83
ns
Bus Relinquish Time
10
83
ns
t9
Throughput Time
4
µs
Conversion Time
Data Valid to BUSY HIGH
25
t12
CS to R/C Setup Time
40
t7
3.3
µs
35
ns
t8
CS
ns
t8
t10
R/C
ns
250
t11
t12
ns
t3
t5
Following a conversion, if R/C and CS are both LOW 250ns
after BUSY rises, then a new conversion will be initiated
without allowing the proper acquisition period for the sample
and hold. R/C must remain HIGH or CS must be taken
HIGH within 250ns of BUSY rising.
D15 - D0
DataValid
Hi-Z State
Hi-Z State
Acquire
MODE
ns
TABLE II. Conversion Timing.
FIGURE 3. Bus Timing.
t1
t5
R/C
t6
t9
CS
t2
t4
BUSY
t8
Hi-Z State
D15 - D0
DataValid
Hi-Z State
t11
t3
MODE
Acquire
Convert
Acquire
t10
FIGURE 2. ADS7815 Timing.
6
ADS7815
www.ti.com
SBAS065B
R/C and CS should remain static prior to that start of
conversion and during the later part of a conversion. To start
a conversion, R/C should be taken LOW at least 100ns
before CS is taken LOW. R/C and/or CS should be taken
HIGH during the early part of the conversion, preferably
within 200ns of the start of the conversion. If these times are
not observed, then there is risk that the transition of these
digital signals may affect the conversion result.
The three NAND gates shown in Figure 1 can be used to
generate R/C and CS signals from a single negative going
pulse.
BUSY
BUSY goes LOW when a conversion is started and remains
LOW throughout the conversion. Just prior to BUSY going
HIGH, the digital outputs become active with the conversion
result. Time t11, shown in Figure 2, should provide adequate
time for the ADS7815 to drive the digital outputs to a valid
logic state before BUSY rises. As shown in Figure 1 and 2,
the rising edge of BUSY can be used to latch the digital
result into an external component.
DIGITAL OUTPUT
The ADS7815’s digital output is in Binary Two’s Complement (BTC) format. Table III shows the relationship between the digital output word and analog input voltage under
ideal conditions.
REFERENCE
The ADS7815 can be operated with the internal 2.5V reference or an external reference. By applying an external
reference to the REF pin, the internal reference is bypassed.
The reference voltage at REF is buffered internally.
The voltage at the reference input sets the full-scale range of
the converter. With the internal 2.5V reference, the input
range is ±2.5V. Thus, the input range of the converter’s
analog input is simply ±VREF, where VREF is the voltage at
the reference input. Because of internal gain and offset error,
the input range will not be exactly ±VREF. The full-scale
error of the converter with an external reference will typically be 0.25% or less. The bipolar zero error will be similar
to that listed in the Electrical Characteristics table. The range
for the external reference is 2.3V to 2.7V.
REF PIN
The REF pin itself should be bypassed with a 0.1µF ceramic
capacitor in parallel with a 2.2µF tantalum capacitor. While
both capacitors should be physically close to the ADS7815,
it is very important that the ceramic capacitor be placed as
close as possible.
The REF voltage should not be used to drive a large load or
any load which is dynamic. A large load will reduce the
reference voltage and the corresponding input range of the
converter. A dynamic load will modulate the reference
voltage and this modulation will be present in the converter’s
output data.
DIGITAL OUTPUT
DESCRIPTION
ANALOG
INPUT
BINARY CODE
HEX CODE
2.499924V
0111 1111 1111 1111
7FFF
Full Scale Range
±2.5V
Least Significant
Bit (LSB)
76µV
+Full Scale
(2.5V – 1LSB)
Midscale
BINARY TWO’S COMPLEMENT
0V
0000 0000 0000 0000
0000
One LSB below
Midscale
–76µV
1111 1111 1111 1111
FFFF
–Full Scale
–2.5V
1000 0000 0000 0000
8000
Table III. Ideal Input Voltages and Output Codes.
CAP PIN
The voltage on the CAP pin is the output of the reference
buffer. This pin should be bypassed with a 0.1µF ceramic
capacitor in parallel with a 2.2µF tantalum capacitor. While
both capacitors should be physically close to the ADS7815,
it is very important that the ceramic capacitor be placed as
close as possible.
The CAP pin connects to the internal reference buffer and
directly to the binary weighted capacitor array of the converter. Thus, the signal at the CAP pin has high-frequency
glitches which occur at each bit decision. For this reason, the
CAP voltage should not be used to provide a reference
voltage for external circuitry.
ADS7815
SBAS065B
www.ti.com
7
LAYOUT
The layout of the ADS7815 and accompanying components
will be critical for optimum performance. Use of an analog
ground plane is essential. Use of +5V and –5V power planes
is not critical as long as the supplies are well bypassed, and
the traces connecting +5V and –5V to the power connector
are not too long or too thin.
The two +VS power pins of the ADS7815 must be tied
together. The voltage source for these pins should also
power the input buffer and the 74HC00 shown in Figure 1.
This supply should separate from the positive +5V supply
for the system’s digital logic
Three ground pins are present on the ADS7815: pin 2, pin 5,
and pin 14. These should all be tied to the analog ground
plane. The analog ground plane should extend underneath
all analog signal conditioning components and up to the
74HC574s (or equivalent components) shown in Figure 1.
The 74HC574s should not be located more than several
inches from the ADS7815.
The ground for the 74HC574s should be connected to the
digital ground. The analog ground plane should extend up to
the 74HC574s but should be kept at least 1/4" (6mm) distant
from the digital ground plane (if present). The analog and
digital grounds planes should not overlap at any point.
INTERMEDIATE LATCHES
The 74HC574s shown in Figure 1 isolate the ADS7815 from
digital signals on a microprocessor, digital signal processor
(DSP), or microcontroller bus. This is necessary because of
the precision needed within the ADS7815. The weight of a
8
single LSB in the ADS7815 is 76µV, and the comparator
must be able to resolve differences in voltage to this level.
External digital signals which transition during the conversion can easily couple onto the substrate and produce voltages larger than this.
In place of the 74HC574s, it might be possible to use a FIFO
or similar type of memory device. For the majority of
systems, it will be difficult to go directly from the ADS7815
into a microcontroller or DSP even if the ADS7815 is not
connected to shared bus. The reason for this is that during a
conversion, the ADS7815 outputs are tri-stated. The only
chance to read the outputs are during the acquisition period.
And, this is not recommended if the data will be read just
prior to the converter going into the hold mode.
SIGNAL CONDITIONING
The ADS7815 input essentially consists of a switch and a
capacitor. In the acquisition or sample mode, the switch is
closed and the input signal drives the capacitor directly.
When a conversion is started, the switch is opened capturing
the input signal at that moment. This voltage is held on the
capacitor for the remainder of the conversion.
While this provides for a wide bandwidth sample and hold
function and results in excellent AC performance, this architecture requires a high bandwidth, precision op amp to drive
the analog input. The op amp and configuration shown in
Figure 1 is highly recommended. The amplifier should be
placed within 1 to 2 inches (25 to 50mm) of the ADS7815,
and the layout guidelines in the OPA628 data sheet should
be strictly followed.
ADS7815
www.ti.com
SBAS065B
Revision History
DATE
REVISION
12/06
B
11/06
PAGE
SECTION
1
Features
—
Entire Document
3
Electrical Characteristics
DESCRIPTION
Changed from "84dB min SINAD" to "82dB min SINAD WITH 100kHz INPUT"
Updated document format to current standard; some page layout changed.
Changed Total Harmonic Distortion max value from –96 to –94.
A
Changed Signal-to-(Noise+Distortion) min value from 84 to 82.
Changed Signal-to-Noise min value from 84 to 82.
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
ADS7815
SBAS065B
www.ti.com
9
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
ADS7815U
ACTIVE
SOIC
DW
28
20
Green (RoHS
& no Sb/Br)
CU NIPDAU-DCC
Level-3-260C-168 HR
-25 to 85
ADS7815U
ADS7815U/1K
ACTIVE
SOIC
DW
28
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU-DCC
Level-3-260C-168 HR
-25 to 85
ADS7815U
ADS7815UE4
ACTIVE
SOIC
DW
28
20
Green (RoHS
& no Sb/Br)
CU NIPDAU-DCC
Level-3-260C-168 HR
-25 to 85
ADS7815U
ADS7815UG4
ACTIVE
SOIC
DW
28
20
Green (RoHS
& no Sb/Br)
CU NIPDAU-DCC
Level-3-260C-168 HR
-25 to 85
ADS7815U
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2015
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
ADS7815U/1K
Package Package Pins
Type Drawing
SOIC
DW
28
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
1000
330.0
32.4
Pack Materials-Page 1
11.35
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
18.67
3.1
16.0
32.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ADS7815U/1K
SOIC
DW
28
1000
367.0
367.0
55.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
Similar pages