IRF IRSM807-105MH Integrated gate drivers and bootstrap functionality Datasheet

IRSM807-105MH
Half-Bridge IPM for Small Appliance
Motor Drive Applications
10A, 500V
Description
IRSM807-105MH is a 10A, 500V half-bridge module designed for advanced appliance motor drive applications such as
energy efficient fans and pumps. IR's technology offers an extremely compact, high performance half-bridge topology in
an isolated package. This advanced IPM offers a combination of IR's low RDS(on) Trench FREDFET technology and the
industry benchmark half-bridge high voltage, rugged driver in a small PQFN package. At only 8x9mm and featuring
integrated bootstrap functionality, the compact footprint of this surface-mount package makes it suitable for applications
that are space-constrained. IRSM807-105MH functions without a heat sink.
Features
•
•
•
•
•
•
•
•
•
•
•
Integrated gate drivers and bootstrap functionality
Suitable for sinusoidal modulation applications
Low RDS(on) Trench FREDFET
Under-voltage lockout for both channels
Matched propagation delay for all channels
Optimized dV/dt for loss and EMI trade offs
3.3V input logic compatible
Active high HIN and LIN
Motor Power range 80-200W
Isolation 1500VRMS min
ROHS compliant
IRSM807-105MH
Internal Electrical Schematic
VB
IRSM807-105MH
V+
VCC
HIN
LIN
Vs
600V Half Bridge
driver with built
in bootstrap
V-
COM
Ordering Information
1
Orderable Part Number
Package Type
Form
Quantity
IRSM807-105MH
PQFN 8x9mm
Tray
1300
IRSM807-105MHTR
PQFN 8x9mm
Tape and Reel
2000
Submit Datasheet Feedback
May 18, 2014
www.irf.com © 2014 International Rectifier
IRSM807-105MH
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the module may occur. These are
not tested at manufacturing. All voltage parameters are absolute voltages referenced to VSS unless otherwise
stated in the table. The thermal resistance rating is measured under board mounted and still air conditions.
Symbol
Description
Min
Max
Unit
BVDSS
MOSFET Blocking Voltage
---
500
V
IO
DC output current per MOSFET @ TC=25°C (Note1)
---
10
A
Pd
Power dissipation per MOSFET @ TC =100°C
---
-
W
TJ (MOSFET & IC)
Maximum Operating Junction Temperature
---
150
°C
TL
Lead temperature (soldering 30 seconds)
---
260
°C
TS
Storage Temperature Range
-40
150
°C
VB
High side floating supply voltage
-0.3
VS + 20
V
VS
High side floating supply offset voltage
VB - 20
VB +0.3
V
VCC
Low Side fixed supply voltage
-0.3
20
V
VIN
Logic input voltage LIN, HIN
-0.3
VCC +0.3
V
VISO
Isolation voltage (1min) (Note2)
---
1500
VRMS
Note1: Calculated based on maximum junction temperature. Bond wires current limit is 3.5A. Note2: Characterized, not tested at
manufacturing
Reccomended Operating Conditions
Symbol
V
+
Description
Positive DC Bus Input Voltage
Min
Typ
Max
Units
---
---
400
V
(Note 3)
---
400
V
VS1,2,3
High Side Floating Supply Offset Voltage
VB1,2,3
High Side Floating Supply Voltage
VS+12
---
VS+20
V
VCC
Low Side and Logic Supply Voltage
13.5
---
16.5
V
VIN
Logic Input Voltage
COM
---
VCC
V
Fp
PWM Carrier Frequency
---
---
20
kHz
Conditions
For proper operation the module should be used within the recommended conditions. All voltages are absolute referenced to COM. The VS
offset is tested with all supplies biased at 15V differential.
Note 3: Logic operational for Vs from COM-8V to COM+500V. Logic state held for Vs from COM-8V to COM-VBS.
2
www.irf.com © 2014 International Rectifier
Submit Datasheet Feedback
May 18, 2014
IRSM807-105MH
Static Electrical Characteristics
VBIAS (VCC, VBS)=15V, TJ=25ºC, unless otherwise specified. The VIN, and IIN parameters are referenced to COM
Symbol
Description
Min
Typ
Max
Units
BVDSS
Drain-to-Source Breakdown Voltage
500
---
---
V
ILKH
Leakage Current of High Side FET’s in
Parallel
---
15
---
µA
ILKL
Leakage Current of Low Side FET’s in
Parallel Plus Gate Drive IC
---
20
---
µA
---
0.58
0.8
RDS(ON)
Drain to Source ON Resistance
1.60
---
VSD
Diode Forward Voltage
---
0.85
---
V
VHIN/LIN
Logic “1” input voltage for HIN & “0” for
LIN
2.2
---
---
V
VHIN/LIN
Logic “0” input voltage for HIN & “1” for
LIN
---
---
0.8
V
VCC and VBS Supply Under-Voltage,
Positive Going Threshold
8
8.9
9.8
V
VCCUV-, VBSUV-
VCC and VBS supply Under-Voltage,
Negative Going Threshold
7.4
8.2
9.0
V
VCCUVH, VBSUVH
VCC and VBS Supply Under-Voltage LockOut Hysteresis
---
0.7
---
V
IQBS
Quiescent VBS Supply Current VIN=0V
---
45
70
µA
IQCC
Quiescent VCC Supply Current VIN=0V
---
1100
3000
µA
IHIN+
Input Bias Current VIN=4V
---
5
20
µA
ILIN-
Input Bias Current VIN=0V
---
1
2
µA
---
200
---
Ω
Min
Typ
Max
Units
---
216
---
mJ
VCCUV+,
VBSUV+
Internal Bootstrap Equivalent Resistor
Value
Note 4: Characterized, not tested at manufacturing
RBR
TJ=25°C, ILK=3mA
TJ=25°C, VDS=500V
TJ=25°C, VDS=500V
TJ=25°C, VCC=10V, Id = 6A
Ω
---
Conditions
TJ=150°C, VCC=10V, Id = 6A
(Note 4)
TJ=25°C, VCC=10V, Id = 6A
TJ=25°C
MOSFET Avalanche Characteristics
Symbol
Description
EAS
Single Pulse Avalanche Energy
Conditions
TJ=25°C, L=3mH, VDD=100V,
IAS=12A, TO-220 package.
Dynamic Electrical Characteristics
VBIAS (VCC, VBS)=15V, TJ=25ºC, unless otherwise specified. Driver only timing unless otherwise specified.
Symbol
Description
Min
Typ
Max
Units
TON
Input to Output Propagation Turn-On
Delay Time
---
0.8
1.3
µs
TOFF
Input to Output Propagation Turn-Off
Delay Time
---
0.8
1.3
µs
TFIL,IN
Input Filter Time (HIN, LIN)
---
300
---
ns
3
www.irf.com © 2014 International Rectifier
Conditions
+
ID=1mA, V =50V
Gate Driver; VLIN=0 & VHIN=5V
with no external deadtime
Submit Datasheet Feedback
May 18, 2014
IRSM807-105MH
Thermal and Mechanical Characteristics
Symbol
Description
Min
Typ
Max
Units
Conditions
Rth(J-B)
Thermal resistance, junction to
mounting pad, each MOSFET
---
0.9
---
°C/W
Standard reflow-solder
process
Rth(J-A)
Thermal resistance, junction to
ambient, each MOSFET
---
40
---
°C/W
Mounted on 13.2cm2 of
two-layer FR4 with 36 vias
Input-Output Logic Level Table
V+
Ho
HIN
Gate
Driver
IC
Vs
Phase
Lo
LIN
HIN
LIN
Phase
HI
LO
V+
LO
HI
0
LO
LO
*
HI
HI
**
* V+ if motor current is flowing into Vs, 0 if current is flowing out of Vs into the motor winding
** Shoot-through condition
4
www.irf.com © 2014 International Rectifier
Submit Datasheet Feedback
May 18, 2014
IRSM807-105MH
Figure 1 – MOS typical output characteristics at 25°C
Figure 2 – MOS typical output characteristics at 25°C
5
www.irf.com © 2014 International Rectifier
Submit Datasheet Feedback
May 18, 2014
IRSM807-105MH
Figure 3 – MOS body diode typical characteristics at 25°C and 150°C
Figure 4 – module top surface typical thermal impedance
6
www.irf.com © 2014 International Rectifier
Submit Datasheet Feedback
May 18, 2014
IRSM807-105MH
Figure 5 – Typical switching losses at 390V
Figure 6 – typical delta temperature between case (no heat-sink) and ambient with 1oz FR4 vs. power dissipation in the
module
7
www.irf.com © 2014 International Rectifier
Submit Datasheet Feedback
May 18, 2014
IRSM807-105MH
Figure 7 – typical delta temperature between case (no heat-sink) and ambient with 2oz FR4 vs. power dissipation in the
module
Figure 8 – Typical thermal resistance vs. power dissipation in the module (no heat sink) with 1oz FR4
8
www.irf.com © 2014 International Rectifier
Submit Datasheet Feedback
May 18, 2014
IRSM807-105MH
Figure 9 – Typical thermal resistance vs. power dissipation in the module (no heat sink) with 2oz FR4
Figure 10 – Typical thermal resistance vs. area per module (no heat sink) with two layers FR4
9
www.irf.com © 2014 International Rectifier
Submit Datasheet Feedback
May 18, 2014
IRSM807-105MH
Qualification†
Industrial††
(per JEDEC JESD 47)
Qualification Level
†††
MSL3
(per IPC/JEDEC J-STD-020)
Moisture Sensitivity Level
Class 1C
(per JEDEC standard ANSI/ESDA/JEDEC JS-001)
Human Body Model
ESD
Class A
(per EIA/JEDEC standard JESD22-A115)
Machine Model
RoHS Compliant
Yes
†
Qualification standards can be found at International Rectifier’s web site http://www.irf.com/
††
Higher qualification ratings may be available should the user have such requirements. Please contact your
International Rectifier sales representative for further information.
†††
Higher MSL ratings may be available for the specific package types listed here. Please contact your International
Rectifier sales representative for further information.
Module Pin-Out Description
Pin
1, 4, 7, 32
2
3
5
8, 9, 10
11 – 19
20 – 28
29 – 30
31
Name
COM
VCC
HIN
LIN
VVS
V+
VS
VB
Description
Low Side Gate Drive Return
15V Gate Drive Supply
Logic Input for High Side (Active High)
Logic Input for Low Side (Active High)
Low Side Source Connection
Phase Output
DC Bus
Phase Output (-ve Bootstrap Cap Connection)
High Side Floating Supply (+ve Bootstrap Cap Connection)
7
6
5
4
3
2
1
8
31
9
30
32
10
29
11
28
12
27
13
26
14
25
15
24
16
23
17
18
19
20
21
22
Exposed pad (Pin 32) has to be connected to COM for better electrical performance
10
www.irf.com © 2014 International Rectifier
Submit Datasheet Feedback May 18, 2014
IRSM807-105MH
Package Outline IRSM807-105MH (Bottom View), 1 of 2
Dimensions in mm
11
www.irf.com © 2014 International Rectifier
Submit Datasheet Feedback May 18, 2014
IRSM807-105MH
Package Outline IRSM807-105MH (Bottom View), 2 of 2
Dimensions in mm
12
www.irf.com © 2014 International Rectifier
Submit Datasheet Feedback May 18, 2014
IRSM807-105MH
Package Outline IRSM807-105MH (Top & Side View)
Dimensions in mm
13
www.irf.com © 2014 International Rectifier
Submit Datasheet Feedback May 18, 2014
IRSM807-105MH
Top Marking
IRSM807-105MH
14
www.irf.com © 2014 International Rectifier
Submit Datasheet Feedback May 18, 2014
IRSM807-105MH
Typical Application Connection IRS807-105MH
VBUS
HVIC
UH
XTAL0
UL
VH
XTAL1
SPD-REF
AIN2
HVIC
HVIC
VCC
VB
VCC
VB
HIN
HO
VH
HIN
HO
WH
HIN
HO
LIN
VS
VL
LIN
VS
WL
LIN
VS
COM
LO
COM
LO
COM
LO
U
VCC
V
VB
W
VL
WH
WL
IRSM807-105MH
IRSM807-105MH
IRSM807-105MH
GATEKILL
IRMCK171
Power
Supply
VDD
VDDCAP
VSS
VDD
AIN1
.
CS_U+
CS_V+
Figure 1: Typical Application Connection
1. Bus capacitors should be mounted as close to the module bus terminals as possible to reduce ringing
and EMI problems. Additional high frequency ceramic capacitor mounted close to the module pins will
further improve performance.
2. In order to provide a good decoupling between VCC-VSS abd VB-VS terminals, the capaciotrs shown
connected at these terminals should be located very close to the module pins. Additional high frequency
capacitors, typically 0.1uF, are recommended.
3. Value of the boot-strap capacitors depends upon the switching frequency. Their selection should be
made based on IR Design tip DT04-4 or application note AN-1044.
15
www.irf.com © 2014 International Rectifier
Submit Datasheet Feedback May 18, 2014
IRSM807-105MH
VDS
ID
ID
VDS
90% ID
50%
HIN /LIN
90% ID
50%
VDS
HIN /LIN
50%
HIN /LIN
HIN /LIN
50%
VCE
10% ID
10% ID
tf
tr
TON
TOFF
Figure 3a. Input to Output propagation turn-on delay
time.
Figure 3b. Input to Output propagation turn-off delay
time.
IF
VDS
HIN /LIN
Irr
trr
Figure 3c. Diode Reverse Recovery
16
www.irf.com © 2014 International Rectifier
Submit Datasheet Feedback May 18, 2014
IRSM807-105MH
Data and Specifications are subject to change without notice
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105
TAC Fax: (310) 252-7903
Visit us at www.irf.com for sales contact information
17
www.irf.com © 2014 International Rectifier
Submit Datasheet Feedback May 18, 2014
Similar pages