NICHIA NCSW170B Built-in esd protection device Datasheet

NICHIA STS-DA1-2948C <Cat.No.150227>
NICHIA CORPORATION
SPECIFICATIONS FOR WHITE LED
NCSW170BT
● Pb-free Reflow Soldering Application
● Built-in ESD Protection Device
● RoHS Compliant
NICHIA STS-DA1-2948C <Cat.No.150227>
SPECIFICATIONS
(1) Absolute Maximum Ratings
Symbol
Absolute Maximum Rating
Unit
Forward Current
Item
IF
1200
mA
Pulse Forward Current
IFP
1500
mA
Allowable Reverse Current
IR
85
mA
Power Dissipation
PD
4.44
W
Operating Temperature
Topr
-40~125
°C
Storage Temperature
Tstg
-40~125
°C
Junction Temperature
TJ
150
°C
* Absolute Maximum Ratings at TS=25°C.
* IFP conditions with pulse width ≤10ms and duty cycle ≤10%.
(2) Initial Electrical/Optical Characteristics
Symbol
Condition
Typ
Max
Unit
Forward Voltage
Item
VF
IF=1000mA
3.4
-
V
Luminous Flux
Φv
IF=1000mA
315
-
lm
x
-
IF=1000mA
0.3292
-
-
y
-
IF=1000mA
0.3439
-
-
Chromaticity Coordinate
Thermal Resistance
RθJS_real
-
4.2
5.4
°C/W
RθJS_el
-
3.0
3.8
°C/W
* Characteristics at TS=25°C.
* Luminous Flux value as per CIE 127:2007 standard.
* Chromaticity Coordinates as per CIE 1931 Chromaticity Chart.
* RθJS_real are decided by taking into account energy conversion efficiency. Please refer to JESD51.
1
NICHIA STS-DA1-2948C <Cat.No.150227>
RANKS
Item
Forward Voltage
Luminous Flux
Rank
Min
Max
Unit
V
-
2.9
3.7
M350
350
400
M300
300
350
M250
250
300
lm
Color Ranks
Rank asw60
Rank sw50
x
0.3163
0.3138
0.3296
0.3300
x
0.3366
0.3376
0.3548
0.3515
y
0.3181
0.3381
0.3526
0.3308
y
0.3369
0.3616
0.3736
0.3487
x
0.3221
0.3207
0.3376
0.3366
y
0.3261
0.3462
0.3616
0.3369
Rank sw57
* Ranking at TS=25°C.
* Forward Voltage Tolerance: ±0.05V
* Luminous Flux Tolerance: ±7%
* Chromaticity Coordinate Tolerance: ±0.005
* LEDs from the above ranks will be shipped.
The rank combination ratio per shipment will be decided by Nichia.
2
NICHIA STS-DA1-2948C <Cat.No.150227>
CHROMATICITY DIAGRAM
0.45
黒体放射軌跡
Blac kbody Loc us
0.40
sw50
y
sw57
0.35
a sw60
0.30
4745K
5310K
6020K
0.25
0.25
0.30
0.35
0.40
0.45
x
3
NICHIA STS-DA1-2948C <Cat.No.150227>
OUTLINE DIMENSIONS
* 本製品はRoHS指令に適合しております。
This product complies with RoHS Directive.
管理番号 No.
NCSW170B
STS-DA7-5259A
(単位 Unit:±0.1)
mm)
(単位 Unit: mm, 公差 Tolerance:
1.45
(1.15)
0.75
(0.51)
1.8
(1.15)
(0.715)
(0.15)
Cathode
1.6
Anode
0.3
内容 Description
パッケージ材質
Package Materials
セラミックス
Ceramics
蛍光体板材質
Phosphor sheet
Materials
硬質ガラス(蛍光体入り)
Hard Glass (with phosphor)
封止樹脂材質
Encapsulating Resin
Materials
シリコーン樹脂
Silicone Resin
電極材質
Electrodes Materials
金メッキ
Au-plated
質量
Weight
0.0057g(TYP)
* バリは寸法に含まないものとします。
Dimensions do not include mold flash.
1.23
K
項目 Item
A
保護素子
Protection Device
4
NICHIA STS-DA1-2948C <Cat.No.150227>
SOLDERING
• Reflow Soldering Condition(Lead-free Solder)
1 to 5°C per sec
260°CMax
10sec Max
Pre-heat
180 to 200°C
60sec Max
Above 220°C
120sec Max
● Recommended Soldering Pad Pattern
1.34
0.3
0.43
1.6
R0.075
1.7
R0.075
● Recommended Metal Solder Stencil Aperture
1.21
(単位 Unit: mm)
* This LED is designed to be reflow soldered on to a PCB. If dip soldered or hand soldered,
Nichia cannot guarantee its reliability.
* Reflow soldering must not be performed more than twice.
* The reflow profile should be determined based on the recommended soldering conditions for the solder paste that is used.
* Avoid rapid cooling. Ramp down the temperature gradually from the peak temperature.
* Nitrogen reflow soldering is recommended. Air flow soldering conditions can cause optical degradation,
caused by heat and/or atmosphere.
* This product uses glass on the emitting surface; if excessive force is applied, it may cause the glass to be damaged,
chipped and/or deformed. If the glass is damaged, chipped and/or deformed, then the internal wires may be damaged
and the reliability may decrease.
Recommended conditions:
Using a nozzle designed for the LEDs is recommended. (See the nozzle drawing below)
Nozzle contact area:
(2)
The center of the phosphor sheet. (See the second figure from the right)
R0.1
2.2
0.4
1.2
(単位 Unit: mm)
If the nozzle is off-center and makes contact with the edges of the phosphor sheet,
it may cause the glass to be chipped and/or damaged. One example of this is shown in the first figure from the right.
Placement pressure ≤3.5N/mm² * max. force: 5N
Vacuum pressure ≤8N/cm²(≤0.8kgf/cm²)
5
NICHIA STS-DA1-2948C <Cat.No.150227>
* Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable,
a hot plate should be used.
It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
* When soldering, do not apply stress to the LED while the LED is hot.
* When using a pick and place machine, choose an appropriate nozzle for this product.
* The recommended soldering pad pattern is designed for attachment of the LED without problems.
When precise mounting accuracy is required, such as high-density mounting, ensure that the size and shape of the pad
are suitable for the circuit design.
* When flux is used, it should be a halogen free flux. Ensure that the manufacturing process is not designed in a manner
where the flux will come in contact with the LEDs.
* Make sure that there are no issues with the type and amount of solder that is being used.
* All of the electrode pads are on the backside of this product; solder connections will not be able to be seen nor confirmed
by a normal visual inspection. When using the product, ensure that there are no issues with the soldering conditions.
6
NICHIA STS-DA1-2948C <Cat.No.150227>
TAPE AND REEL DIMENSIONS
0.20±0.05
Nxxx170x
STS-DA7-7109
(単位 Unit: mm)
2 ±0.05
3.5 ±0.05
2±0.05
1.75 ±0.1
4±0.1
Φ1.5+0.1
-0
管理番号 No.
8 ±0.1
テーピング部 Tape
0.95±0.05
4±0.1
Φ1+0.2
-0
1.65±0.05
エンボスキャリアテープ
Embossed Carrier Tape
トレーラ部/リーダ部 Trailer and Leader
トップカバーテープ
Top Cover Tape
引き出し方向
Feed
Direction
トレーラ部最小160mm(空部)
Trailer 160mm MIN(Empty Pockets)
LED装着部
Loaded Pockets
引き出し部最小100mm(空部)
Leader with Top Cover Tape
100mm MIN(Empty Pocket)
リーダ部最小400mm
Leader without Top Cover Tape 400mm MIN
リール部 Reel
180+0
-3
11.4±1
9±0.3
* 数量は1リールにつき 3500個入りです。
Reel Size: 3500pcs
Φ
* JIS C 0806電子部品テーピングに準拠しています。
The tape packing method complies with JIS C 0806
(Packaging of Electronic Components on Continuous Tapes).
±
21
±0.2
ラベル
Label
Φ
13 ±
0.
2
f 13
.8
Φ60 +1
-0
8
0.
f2
1 ±0
* 実装作業の中断などでエンボスキャリアテープをリールに巻き取る場合、
エンボスキャリアテープを強く(10N以上)締めないで下さい。
LEDがカバーテープに貼り付く可能性があります。
When the tape is rewound due to work interruptions,
no more than 10N should be applied to
the embossed carrier tape.
The LEDs may stick to the top cover tape.
7
NICHIA STS-DA1-2948C <Cat.No.150227>
PACKAGING - TAPE & REEL
シリカゲルとともにリールをアルミ防湿袋に入れ、熱シールにより封をします。
Reels are shipped with desiccants in heat-sealed moisture-proof bags.
管理番号 No.
Nxxxxxxx
STS-DA7-0006C
ラベル Label
リール
Reel
シリカゲル
Desiccants
XXXX LED
TYPE Nxxxxxxx
*******
LOT YMxxxx-RRR
QTY.
PCS
RoHS
NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
熱シール
Seal
アルミ防湿袋
Moisture-proof Bag
アルミ防湿袋を並べて入れ、ダンボールで仕切ります。
Moisture-proof bags are packed in cardboard boxes
with corrugated partitions.
ラベル Label
XXXX LED
TYPE Nxxxxxxx
*******
RANK RRR
PCS
QTY.
RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Nichia
LED
* 客先型名を*******で示します。
客先型名が設定されていない場合は空白です。
******* is the customer part number.
If not provided, it will not be indicated on the label.
* ロット表記方法についてはロット番号の項を
参照して下さい。
For details, see "LOT NUMBERING CODE"
in this document.
* ランク分けがない場合はランク表記はありません。
The label does not have the RANK field for
un-ranked products.
* 本製品はテーピングしたのち、輸送の衝撃から保護するためダンボールで梱包します。
Products shipped on tape and reel are packed in a moisture-proof bag.
They are shipped in cardboard boxes to protect them from external forces during transportation.
* 取り扱いに際して、落下させたり、強い衝撃を与えたりしますと、製品を損傷させる原因になりますので注意して下さい。
Do not drop or expose the box to external forces as it may damage the products.
* ダンボールには防水加工がされておりませんので、梱包箱が水に濡れないよう注意して下さい。
Do not expose to water. The box is not water-resistant.
* 輸送、運搬に際して弊社よりの梱包状態あるいは同等の梱包を行って下さい。
Using the original package material or equivalent in transit is recommended.
8
NICHIA STS-DA1-2948C <Cat.No.150227>
LOT NUMBERING CODE
Lot Number is presented by using the following alphanumeric code.
YMxxxx - RRR
Y - Year
Year
Y
2014
E
2015
F
2016
G
2017
H
2018
I
2019
J
M - Month
Month
M
Month
M
1
1
7
7
2
2
8
8
3
3
9
9
4
4
10
A
5
5
11
B
6
6
12
C
xxxx-Nichia's Product Number
RRR-Ranking by Color Coordinates, Ranking by Luminous Flux
9
NICHIA STS-DA1-2948C <Cat.No.150227>
DERATING CHARACTERISTICS
NCSx170B
管理番号 No. STS-DA7-6974A
はんだ接合部温度(カソード側)-許容順電流特性
Solder Temperature(Cathode Side) vs
Allowable Forward Current
Derating2
許容順電流
Allowable Forward Current(mA)
1500
(125, 1200)
1200
900
600
300
0
0
30
60
90
120
150
はんだ接合部温度(カソード側)
Solder Temperature(Cathode Side)(°C)
デューティー比-許容順電流特性
Duty Ratio vs
Allowable Forward Current
Duty
T A =25°C
許容順電流
Allowable Forward Current(mA)
10000
1500
1200
1000
100
1
10
100
デューティー比
Duty Ratio(%)
10
NICHIA STS-DA1-2948C <Cat.No.150227>
OPTICAL CHARACTERISTICS
NCSW170B
管理番号 No. STS-DA7-5253B
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
発光スペクトル
Spectrum
TA =25°C
IFP=1000mA
Spectrum
1.0
相対発光強度
Relative Emission Intensity(a.u.)
0.8
0.6
0.4
0.2
0.0
350
400
450
500
550
600
650
700
750
波長
Wavelength(nm)
Directivity1
指向特性
Directivity
TA =25°C
IFP=1000mA
-20°
-10°
0°
10°
20°
30°
-30°
40°
放射角度
Radiation Angle
-40°
50°
-50°
-60°
60°
-70°
70°
80°
-80°
-90°
90°
1
0.5
0
0.5
1
相対照度
Relative Illuminance(a.u.)
11
NICHIA STS-DA1-2948C <Cat.No.150227>
FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS
NCSW170B
管理番号 No. STS-DA7-5254B
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
順電圧-順電流特性
Forward Voltage vs
Forward Current
周囲温度-順電圧特性
Ambient Temperature vs
Forward Voltage
VfIf
TA =25°C
1500
1000
100
3.5
3.0
2.5
2.5
3.0
3.5
4.0
-60
-30
順電圧
Forward Voltage(V)
順電流-相対光束特性
Forward Current vs
Relative Luminous Flux
0
30
60
90
120
150
周囲温度
Ambient Temperature(°C)
周囲温度-相対光束特性
Ambient Temperature vs
Relative Luminous Flux
IfIv
TA =25°C
2.0
TaIv
IFP=1000mA
1.4
相対光束
Relative Luminous Flux(a.u.)
相対光束
Relative Luminous Flux(a.u.)
IFP=1000mA
4.0
順電圧
Forward Voltage(V)
順電流
Forward Current(mA)
10000
TaVf
1.5
1.0
0.5
1.2
1.0
0.8
0.6
0.0
0
300
600
900
1200
順電流
Forward Current(mA)
1500
1800
-60
-30
0
30
60
90
120
150
周囲温度
Ambient Temperature(°C)
12
NICHIA STS-DA1-2948C <Cat.No.150227>
FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS
NCSW170B
管理番号 No. STS-DA7-5255B
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
順電流-色度 特性
Forward Current vs
Chromaticity Coordinate
Ifxy
TA =25°C
0.37
0.36
y
100mA
350mA
0.35
0.34
1000mA
1200mA
1500mA
0.33
0.31
0.32
0.33
0.34
0.35
x
周囲温度-色度 特性
Ambient Temperature vs
Chromaticity Coordinate
Taxy
IFP= 1000mA
0.37
y
0.36
0.35
25°C
125°C
0°C
0.34
-40°C
0.33
0.31
0.32
0.33
0.34
0.35
x
13
NICHIA STS-DA1-2948C <Cat.No.150227>
RELIABILITY
(1) Tests and Results
Reference
Test
Standard
Resistance to
Test
Test Conditions
Duration
JEITA ED-4701
Tsld=260°C, 10sec, 2reflows,
300 301
Precondition: 30°C, 70%RH, 168hr
Solderability
JEITA ED-4701
Tsld=245±5°C, 5sec,
(Reflow Soldering)
303 303A
Lead-free Solder(Sn-3.0Ag-0.5Cu)
Soldering Heat
(Reflow Soldering)
JEITA ED-4701
Thermal Shock
300 307
#2
0/10
100cycles
#1
0/50
100cycles
#1
0/10
10cycles
#1
0/10
TA=125°C
1000hours
#1
0/10
TA=85°C, RH=85%
1000hours
#1
0/10
TA=-40°C
1000hours
#1
0/10
TA=25°C, IF=1200mA
1000hours
#1
0/10
TA=125°C, IF=540mA
1000hours
#1
0/10
85°C, RH=85%, IF=1000mA
1000hours
#1
0/10
TA=-40°C, IF=1200mA
1000hours
#1
0/10
1time
#1
0/10
48minutes
#1
0/10
#1
0/10
-40°C to 125°C, 1min dwell,
10sec transfer,
Precondition: 30°C, 70%RH, 168hr
-40°C(30min)~25°C(5min)~
125°C(30min)~25°C(5min)
Moisture Resistance
JEITA ED-4701
25°C~65°C~-10°C, 90%RH,
(Cyclic)
200 203
24hr per cycle
High Temperature
JEITA ED-4701
Storage
200 201
Temperature Humidity
JEITA ED-4701
Storage
100 103
Low Temperature
JEITA ED-4701
Storage
200 202
Room Temperature
Operating Life
High Temperature
Operating Life
Temperature Humidity
Operating Life
Low Temperature
Operating Life
Vibration
Electrostatic Discharges
Failed/Tested
0/10
100 105
Permanence of Marking
#
Units
#1
JEITA ED-4701
Temperature Cycle
Failure
Criteria
JEITA ED-4701
Isopropyl Alcohol, 23±5°C,
500 501
Dipping Time: 5min
JEITA ED-4701
200m/s2, 100~2000~100Hz,
400 403
4cycles, 4min, each X, Y, Z
JEITA ED-4701
HBM, 2kV, 1.5kΩ, 100pF, 3pulses,
300 304
alternately positive or negative
NOTES:
1) RθJA≈13.0°C/W
2) Measurements are performed after allowing the LEDs to return to room temperature.
(2) Failure Criteria
Criteria #
#1
#2
Items
Conditions
Failure Criteria
Forward Voltage(VF)
IF=1000mA
>U.S.L.×1.1
Luminous Flux(ΦV)
IF=1000mA
<L.S.L.×0.7
Solderability
-
Less than 95% solder coverage
U.S.L. : Upper Specification Limit
L.S.L. : Lower Specification Limit
14
NICHIA STS-DA1-2948C <Cat.No.150227>
CAUTIONS
(1) Storage
Conditions
Storage
Temperature
Humidity
Time
Before Opening Aluminum Bag
≤30°C
≤90%RH
Within 1 Year from Delivery Date
After Opening Aluminum Bag
≤30°C
≤70%RH
≤168hours
65±5°C
-
≥24hours
Baking
● Product complies with JEDEC MSL 3 or equivalent. See IPC/JEDEC STD-020 for moisture-sensitivity details.
● Absorbed moisture in LED packages can vaporize and expand during soldering, which can cause interface delamination
and result in optical performance degradation. Products are packed in moisture-proof aluminum bags
to minimize moisture absorption during transportation and storage.
Included silica gel desiccants change from blue to red if moisture had penetrated bags.
● After opening the moisture-proof aluminum bag, the products should go through the soldering process
within the range of the conditions stated above. Unused remaining LEDs should be stored with silica gel desiccants
in a hermetically sealed container, preferably the original moisture-proof bags for storage.
● After the “Period After Opening” storage time has been exceeded or silica gel desiccants are no longer blue,
the products should be baked. Baking should only be done once.
● Although the leads or electrode pads (anode and cathode) of the product are plated with gold,
prolonged exposure to a corrosive environment might cause the gold plated the leads or electrode pads to tarnish,
and thus leading to difficulties in soldering. If unused LEDs remain, they must be stored in a hermetically sealed container.
Nichia recommends using the original moisture-proof bag for storage.
● Do not use sulfur-containing materials in commercial products. Some materials, such as seals and adhesives, may contain sulfur.
The contaminated plating of LEDs might cause an open circuit. Silicone rubber is recommended as a material for seals.
Bear in mind, the use of silicones may lead to silicone contamination of electrical contacts inside the products,
caused by low molecular weight volatile siloxane.
● To prevent water condensation, please avoid large temperature and humidity fluctuations for the storage conditions.
● Do not store the LEDs in a dusty environment.
● Do not expose the LEDs to direct sunlight and/or an environment where the temperature is higher than
normal room temperature.
(2) Directions for Use
● When designing a circuit, the current through each LED must not exceed the Absolute Maximum Rating.
Operating at a constant current per LED is recommended. In case of operating at a constant voltage, Circuit B is recommended.
If the LEDs are operated with constant voltage using Circuit A, the current through the LEDs may vary due to the variation
in Forward Voltage characteristics of the LEDs.
(A)
(B)
...
...
● This product should be operated using forward current. Ensure that the product is not subjected to
either forward or reverse voltage while it is not in use. In particular, subjecting it to continuous reverse voltage
may cause migration, which may cause damage to the LED die. When used in displays that are not used for a long time,
the main power supply should be switched off for safety.
● It is recommended to operate the LEDs at a current greater than 10% of the sorting current to stabilize the LED characteristics.
● Ensure that excessive voltages such as lightning surges are not applied to the LEDs.
● For outdoor use, necessary measures should be taken to prevent water, moisture and salt air damage.
15
NICHIA STS-DA1-2948C <Cat.No.150227>
(3) Handling Precautions
● Do not handle the LEDs with bare hands as it will contaminate the LED surface and may affect the optical characteristics:
it might cause the LED to be deformed and/or the bump to break, which will cause the LED not to illuminate.
● When handling the product with tweezers, be careful not to apply excessive force to the resin.
Otherwise, The resin can be cut, chipped, delaminate or deformed, causing bump-bond breaks and catastrophic failures.
● Dropping the product may cause damage.
● Do not stack assembled PCBs together. Failure to comply can cause the resin portion of the product to be cut, chipped,
delaminated and/or deformed. It may cause bump to break, leading to catastrophic failures.
(4) Design Consideration
● PCB warpage after mounting the products onto a PCB can cause the package to break.
The LED should be placed in a way to minimize the stress on the LEDs due to PCB bow and twist.
● The position and orientation of the LEDs affect how much mechanical stress is exerted on the LEDs placed near the score lines.
The LED should be placed in a way to minimize the stress on the LEDs due to board flexing.
● Board separation must be performed using special jigs, not using hands.
● When using an aluminum base PCB, verify that the PCB will not cause any malfunctions to the LED.
Thermal stress during use can cause the solder joints to crack.
Ensure an insulating layer with a low modulus of elasticity is used for the insulating layer of the aluminum base PCB.
● Ensure that the chosen land pattern has a solder mask which does not cover the copper pads
that the LED will be attached to or the area underneath the LED.
(Non Solder Mask Defined [NSMD] pads are recommended, see the figure below.)
製品実装後
製品実装前
After Mounting Before Mounting
the LED
the LED
NSMD(推奨 Recommended)
ソルダーレジスト 銅箔パッド
Solder Mask Copper Pad
SMD(参考 Reference)
ソルダーレジスト 銅箔パッド
Solder Mask Copper Pad
基材
Base Material
はんだペースト
Solder Paste
製品
LED
基材
Base Material
はんだペースト
Solder Paste
製品
LED
(5) Electrostatic Discharge (ESD)
● The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability.
When handling the products, the following measures against electrostatic discharge are strongly recommended:
Eliminating the charge
Grounded wrist strap, ESD footwear, clothes, and floors
Grounded workstation equipment and tools
ESD table/shelf mat made of conductive materials
● Ensure that tools, jigs and machines that are being used are properly grounded and
that proper grounding techniques are used in work areas. For devices/equipment that mount the LEDs,
protection against surge voltages should also be used.
● If tools or equipment contain insulating materials such as glass or plastic,
the following measures against electrostatic discharge are strongly recommended:
Dissipating static charge with conductive materials
Preventing charge generation with moisture
Neutralizing the charge with ionizers
● The customer is advised to check if the LEDs are damaged by ESD
when performing the characteristics inspection of the LEDs in the application.
Damage can be detected with a forward voltage measurement or a light-up test at low current (≤1mA).
● ESD damaged LEDs may have current flow at a low voltage or no longer illuminate at a low current.
Failure Criteria: VF<2.0V at IF=0.5mA
16
NICHIA STS-DA1-2948C <Cat.No.150227>
(6) Thermal Management
● Proper thermal management is an important when designing products with LEDs. LED die temperature is affected
by PCB thermal resistance and LED spacing on the board. Please design products in a way that the LED die temperature
does not exceed the maximum Junction Temperature (TJ).
● Drive current should be determined for the surrounding ambient temperature (TA) to dissipate the heat from the product.
(7) Cleaning
● The LEDs should not be cleaned with water, benzine, and/or thinner.
● If required, isopropyl alcohol (IPA) should be used. Other solvents may cause premature failure to the LEDs
due to the damage to the resin portion. The effects of such solvents should be verified prior to use.
In addition, the use of CFCs such as Freon is heavily regulated.
● When dust and/or dirt adheres to the LEDs, soak a cloth with Isopropyl alcohol (IPA), then squeeze it before wiping the LEDs.
● Ultrasonic cleaning is not recommended since it may have adverse effects on the LEDs
depending on the ultrasonic power and how LED is assembled.
If ultrasonic cleaning must be used, the customer is advised to make sure the LEDs will not be damaged prior to cleaning.
(8) Eye Safety
● In 2006, the International Electrical Commission (IEC) published IEC 62471:2006 Photobiological safety of lamps
and lamp systems, which added LEDs in its scope.
On the other hand, the IEC 60825-1:2007 laser safety standard removed LEDs from its scope.
However, please be advised that some countries and regions have adopted standards
based on the IEC laser safety standard IEC 60825-1:20112001, which still includes LEDs in its scope.
Most of Nichia's LEDs can be classified as belonging into either the Exempt Group or Risk Group 1.
High-power LEDs, that emit light containing blue wavelengths, may be classified as Risk Group 2.
Please proceed with caution when viewing directly any LEDs driven at high current, or viewing LEDs
with optical instruments which may greatly increase the damages to your eyes.
● Viewing a flashing light may cause eye discomfort. When incorporating the LED into your product,
please be careful to avoid adverse effects on the human body caused by light stimulation.
(9) Others
● The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment,
communications equipment, measurement instruments and household appliances).
Consult Nichia's sales staff in advance for information on the applications in which exceptional quality
and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or
health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control system, automobiles,
traffic control equipment, life support systems and safety devices).
● The customer shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent
from Nichia. When defective LEDs are found, the customer shall inform Nichia directly before disassembling or analysis.
● The specifications and appearance of this product may change without notice;
Nichia does not guarantee the contents of this specification. Both the customer and Nichia
will agree on the official specifications of supplied products before the volume production of a program begins.
17
Similar pages