FERRITE CHIP INDUCTORS L201610 SERIES 1. PART NO. EXPRESSION : L 2 0 1 6 1 0 1 R 0 M - □□ (a) Series code (d) Tolerance code : M = ± 20% (a) (b) Dimension code (e) 10: Standard (c) (d) (b) (e) (c) Inductance code : 1R0 = 1.0uH 11 ~ 99 : Internal control number 2. CONFIGURATION & DIMENSIONS : A D C B Unit:m/m B A 2.0 ± 0.15 1.6 ± 0.15 C D 0.9± 0.1 0.3~0.7 3. SCHEMATIC : 4. MATERIALS : b a Ag(100%) Ni(100%)-1.5um(min.) (a) Body : Ferrite (b) Termination : Ag/Ni/Sn Sn(100%)-3.0um(min.) 5. GENERAL SPECIFICATION : a) Operating temp. : -55° C to +125° C b) Storage condition (component in its packaging) i) Temperature : -10 to 40° C ii) Humidity : 60% NOTE : Specifications subject to change without notice. Please check our website for latest information. 30.01.2015 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 1 FERRITE CHIP INDUCTORS L201610 SERIES 6. ELECTRICAL CHARACTERISTICS : Inductance Test Frequency Rated Current DC Resistance SRF (μH) (MHz) (mA) Max (Ω) (MHz) Min L201610R47M-10 0.47 ± 20% 1 1500 0.14 ± 30% 100 L201610R68M-10 0.68 ± 20% 1 1500 0.15 ± 30% 90 L201610R82M-10 0.82 ± 20% 1 1500 0.16 ± 30% 80 Part Number L2016101R0M-10 1.0 ± 20% 1 1400 0.16 ± 30% 60 L2016101R2M-10 1.2 ± 20% 1 1400 0.16 ± 30% 60 L2016101R5M-10 1.5 ± 20% 1 1200 0.20 ± 30% 50 L2016101R8M-10 1.8 ± 20% 1 1200 0.20 ± 30% 50 L2016102R2M-10 2.2 ± 20% 1 1200 0.22 ± 30% 40 L2016103R3M-10 3.3 ± 20% 1 1100 0.24 ± 30% 30 L2016104R7M-10 4.7 ± 20% 1 1100 0.30 ± 30% 20 NOTE : Specifications subject to change without notice. Please check our website for latest information. 30.01.2015 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 2 FERRITE CHIP INDUCTORS L201610 SERIES 7. CHARACTERISTICS CURVES : L2016101R0M L2016101R5M L2016102R2M L2016103R3M L2016104R7M L2016101R0M L2016101R5M L2016102R2M L2016103R3M L2016104R7M NOTE : Specifications subject to change without notice. Please check our website for latest information. 30.01.2015 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 3 FERRITE CHIP INDUCTORS L201610 SERIES 8. SOLDERING AND MOUNTING : 8-1. Reflow soldering conditions Pre-heating should be in such a way that the temperature difference between solder and ferrite surface is limited to 150° C max. Also cooling into the solvent after soldering should be in such a way that the temperature difference is limited to 100° C max. Insufficient pre-heating may cause cracks on the ferrite, resulting in the deterioration of product quality. Products should be soldered within the following allowable range indicated by the slanted line. The excessive soldering conditions may cause the corrosion of the electrode. When soldering is repeated, allowable time is the accumulated time. A TEMPERATURE ° C main heating E 230° C Slope of temp. rise Heat time 1 to 5 ° C/sec 50 to 150 sec 120 to 180 ° C B Heat temperature 180° C pre-heating 120° C normal temperature A B C C Slope of temp. rise 1 to 5 ° C/sec D Time over 230° C 90 ~ 120 sec Peak temperature 255 ~ 260 ° C E D TIME(sec.) Peak hold time 10 max. sec No. of mounting 3 times (Melting area of solder) 8-2. Soldering Iron Products attachment with soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. Note : a) Preheat circuit and products to 150° C. b) 280° C tip temperature (max) c) Use a 30 watt max. soldering iron with tip diameter of 3.0mm d) Limit soldering time to 3 secs. 8-3. Solder Volume : Upper limit Accordingly increasing the solder volume, the mechanical stress to product is also increased. Exceeding solder volume may cause the failure of mechanical or electrical performance. Solder shall be used not to be exceed as shown in right side. t Recommendable NOTE : Specifications subject to change without notice. Please check our website for latest information. 30.01.2015 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 4 FERRITE CHIP INDUCTORS L201610 SERIES 9. PACKAGING INFORMATION : 9-1. Paper Carrier Tape Packaging Do:1.55± 0.05 Po:4± 0.1 T W:8.0± 0.1 A F:3.5± 0.05 Bo E:1.75± 0.1 P2:2± 0.05 K P1 A Section A-A Ao(mm) 1.88± 0.10 Unreeling direction Ao D1:1± 0.1 Bo(mm) K(mm) P1(mm) T(mm) 2.4± 0.10 1.23± 0.15 4.00± 0.10 0.23± 0.05 9-2. Leader And Trailer Tape Components Trailer Empty compartments Leader End Start 20 pitch or more 110mm or more 400 ~ 560mm 9-3. Configuration W1 2± 0.5 ± 0.5 A(mm) N(mm) W1(mm) W2(mm) QTY (PCS) 178± 2.0 50 Min. 10± 1.5 20 Max. 3000/Reel A N 13.0 ± 21 8 0. R1.0 W2 NOTE : Specifications subject to change without notice. Please check our website for latest information. 30.01.2015 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 5 FERRITE CHIP INDUCTORS L201610 SERIES 9-4. Tearing Off Force F 165° to 180° Peeling Strength of Cover Tape Top cover tape Cover Tape 10g ~ 100g Base tape Peel Speed : 300mm/min 9-5. Packaging 1. Reel and a bag of desiccant shall be packed in Nylon or plastic bag 2. Maximum of 5 bags shall be packed in an inner box 3. Maximum of 6 inner boxes shall be packed in an outer box Application Notice 1. Storage Conditions : To maintain the solderabililty of terminal electrodes : a) Recommended products should be used within 12 months from the time of delivery. b) The packaging material should be kept where no chlorine or sulfur exists in the air. 2. Transportation : a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils. b) The use of tweezers or vacuum pick up is strongly recommended for individual components. c) Bulk handling should ensure that abrasion and mechanical shock are minimized. NOTE : Specifications subject to change without notice. Please check our website for latest information. 30.01.2015 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 6