TI NX5032GA-12 This data sheet provides reference information for the tm4c123be6pz microcontroller, describing Datasheet

TE X AS I NS TRUM E NTS - P RO DUCTION D ATA
Tiva™ TM4C123BE6PZ Microcontroller
(identical to LM4F212E5QC)
D ATA SH E E T
D S -T M 4C 123BE 6 P Z - 1 5 0 3 3 . 2 6 7 2
S P M S 366B
C o p yri g h t © 2 0 07-2013
Te xa s In stru me n ts In co rporated
Copyright
Copyright © 2007-2013 Texas Instruments Incorporated All rights reserved. Tiva and TivaWare are trademarks of Texas Instruments Incorporated. ARM
and Thumb are registered trademarks and Cortex is a trademark of ARM Limited. Other names and brands may be claimed as the property of others.
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard
warranty. Production processing does not necessarily include testing of all parameters.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor
products and disclaimers thereto appears at the end of this data sheet.
Texas Instruments Incorporated
108 Wild Basin, Suite 350
Austin, TX 78746
http://www.ti.com/tm4c
http://www-k.ext.ti.com/sc/technical-support/product-information-centers.htm
2
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Table of Contents
Revision History ............................................................................................................................. 34
About This Document .................................................................................................................... 36
Audience ..............................................................................................................................................
About This Manual ................................................................................................................................
Related Documents ...............................................................................................................................
Documentation Conventions ..................................................................................................................
36
36
36
37
1
Architectural Overview .......................................................................................... 39
1.1
1.2
1.3
1.3.1
1.3.2
1.3.3
1.3.4
1.3.5
1.3.6
1.3.7
1.3.8
1.4
1.5
1.6
Tiva™ C Series Overview .............................................................................................. 39
TM4C123BE6PZ Microcontroller Overview ..................................................................... 40
TM4C123BE6PZ Microcontroller Features ...................................................................... 42
ARM Cortex-M4F Processor Core .................................................................................. 42
On-Chip Memory ........................................................................................................... 44
Serial Communications Peripherals ................................................................................ 46
System Integration ........................................................................................................ 49
Advanced Motion Control ............................................................................................... 55
Analog .......................................................................................................................... 58
JTAG and ARM Serial Wire Debug ................................................................................ 59
Packaging and Temperature .......................................................................................... 60
TM4C123BE6PZ Microcontroller Hardware Details .......................................................... 60
Kits .............................................................................................................................. 60
Support Information ....................................................................................................... 60
2
The Cortex-M4F Processor ................................................................................... 61
2.1
2.2
2.2.1
2.2.2
2.2.3
2.2.4
2.3
2.3.1
2.3.2
2.3.3
2.3.4
2.3.5
2.3.6
2.4
2.4.1
2.4.2
2.4.3
2.4.4
2.4.5
2.4.6
2.4.7
2.5
2.5.1
Block Diagram .............................................................................................................. 62
Overview ...................................................................................................................... 63
System-Level Interface .................................................................................................. 63
Integrated Configurable Debug ...................................................................................... 63
Trace Port Interface Unit (TPIU) ..................................................................................... 64
Cortex-M4F System Component Details ......................................................................... 64
Programming Model ...................................................................................................... 65
Processor Mode and Privilege Levels for Software Execution ........................................... 65
Stacks .......................................................................................................................... 66
Register Map ................................................................................................................ 66
Register Descriptions .................................................................................................... 68
Exceptions and Interrupts .............................................................................................. 84
Data Types ................................................................................................................... 84
Memory Model .............................................................................................................. 84
Memory Regions, Types and Attributes ........................................................................... 87
Memory System Ordering of Memory Accesses .............................................................. 87
Behavior of Memory Accesses ....................................................................................... 87
Software Ordering of Memory Accesses ......................................................................... 88
Bit-Banding ................................................................................................................... 89
Data Storage ................................................................................................................ 91
Synchronization Primitives ............................................................................................. 92
Exception Model ........................................................................................................... 93
Exception States ........................................................................................................... 94
July 17, 2013
3
Texas Instruments-Production Data
Table of Contents
2.5.2
2.5.3
2.5.4
2.5.5
2.5.6
2.5.7
2.6
2.6.1
2.6.2
2.6.3
2.6.4
2.7
2.7.1
2.7.2
2.8
Exception Types ............................................................................................................ 94
Exception Handlers ....................................................................................................... 98
Vector Table .................................................................................................................. 99
Exception Priorities ....................................................................................................... 99
Interrupt Priority Grouping ............................................................................................ 100
Exception Entry and Return ......................................................................................... 100
Fault Handling ............................................................................................................. 103
Fault Types ................................................................................................................. 104
Fault Escalation and Hard Faults .................................................................................. 104
Fault Status Registers and Fault Address Registers ...................................................... 105
Lockup ....................................................................................................................... 105
Power Management .................................................................................................... 106
Entering Sleep Modes ................................................................................................. 106
Wake Up from Sleep Mode .......................................................................................... 106
Instruction Set Summary .............................................................................................. 107
3
Cortex-M4 Peripherals ......................................................................................... 114
3.1
3.1.1
3.1.2
3.1.3
3.1.4
3.1.5
3.2
3.3
3.4
3.5
3.6
3.7
Functional Description ................................................................................................. 114
System Timer (SysTick) ............................................................................................... 115
Nested Vectored Interrupt Controller (NVIC) .................................................................. 116
System Control Block (SCB) ........................................................................................ 117
Memory Protection Unit (MPU) ..................................................................................... 117
Floating-Point Unit (FPU) ............................................................................................. 122
Register Map .............................................................................................................. 126
System Timer (SysTick) Register Descriptions .............................................................. 129
NVIC Register Descriptions .......................................................................................... 133
System Control Block (SCB) Register Descriptions ........................................................ 148
Memory Protection Unit (MPU) Register Descriptions .................................................... 177
Floating-Point Unit (FPU) Register Descriptions ............................................................ 186
4
JTAG Interface ...................................................................................................... 192
4.1
4.2
4.3
4.3.1
4.3.2
4.3.3
4.3.4
4.4
4.5
4.5.1
4.5.2
Block Diagram ............................................................................................................
Signal Description .......................................................................................................
Functional Description .................................................................................................
JTAG Interface Pins .....................................................................................................
JTAG TAP Controller ...................................................................................................
Shift Registers ............................................................................................................
Operational Considerations ..........................................................................................
Initialization and Configuration .....................................................................................
Register Descriptions ..................................................................................................
Instruction Register (IR) ...............................................................................................
Data Registers ............................................................................................................
193
193
194
194
196
196
197
199
200
200
202
5
System Control ..................................................................................................... 204
5.1
5.2
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
Signal Description .......................................................................................................
Functional Description .................................................................................................
Device Identification ....................................................................................................
Reset Control ..............................................................................................................
Non-Maskable Interrupt ...............................................................................................
Power Control .............................................................................................................
Clock Control ..............................................................................................................
4
204
204
204
205
210
210
211
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
5.2.6
5.3
5.4
5.5
5.6
System Control ...........................................................................................................
Initialization and Configuration .....................................................................................
Register Map ..............................................................................................................
System Control Register Descriptions ...........................................................................
System Control Legacy Register Descriptions ...............................................................
218
222
223
228
414
6
System Exception Module ................................................................................... 478
6.1
6.2
6.3
Functional Description ................................................................................................. 478
Register Map .............................................................................................................. 478
Register Descriptions .................................................................................................. 478
7
Hibernation Module .............................................................................................. 486
7.1
7.2
7.3
7.3.1
7.3.2
7.3.3
7.3.4
7.3.5
7.3.6
7.3.7
7.3.8
7.3.9
7.3.10
7.3.11
7.3.12
7.4
7.4.1
7.4.2
7.4.3
7.4.4
7.4.5
7.5
7.6
Block Diagram ............................................................................................................
Signal Description .......................................................................................................
Functional Description .................................................................................................
Register Access Timing ...............................................................................................
Hibernation Clock Source ............................................................................................
System Implementation ...............................................................................................
Battery Management ...................................................................................................
Real-Time Clock ..........................................................................................................
Battery-Backed Memory ..............................................................................................
Power Control Using HIB .............................................................................................
Power Control Using VDD3ON Mode ...........................................................................
Initiating Hibernate ......................................................................................................
Waking from Hibernate ................................................................................................
Arbitrary Power Removal .............................................................................................
Interrupts and Status ...................................................................................................
Initialization and Configuration .....................................................................................
Initialization .................................................................................................................
RTC Match Functionality (No Hibernation) ....................................................................
RTC Match/Wake-Up from Hibernation .........................................................................
External Wake-Up from Hibernation ..............................................................................
RTC or External Wake-Up from Hibernation ..................................................................
Register Map ..............................................................................................................
Register Descriptions ..................................................................................................
487
487
488
488
489
490
491
492
494
494
494
494
495
495
495
496
496
497
497
497
498
498
499
8
Internal Memory ................................................................................................... 517
8.1
8.2
8.2.1
8.2.2
8.2.3
8.2.4
8.3
8.4
8.5
8.6
Block Diagram ............................................................................................................ 517
Functional Description ................................................................................................. 518
SRAM ........................................................................................................................ 518
ROM .......................................................................................................................... 519
Flash Memory ............................................................................................................. 521
EEPROM .................................................................................................................... 526
Register Map .............................................................................................................. 532
Flash Memory Register Descriptions (Flash Control Offset) ............................................ 533
EEPROM Register Descriptions (EEPROM Offset) ........................................................ 551
Memory Register Descriptions (System Control Offset) .................................................. 568
9
Micro Direct Memory Access (μDMA) ................................................................ 576
9.1
9.2
Block Diagram ............................................................................................................ 577
Functional Description ................................................................................................. 577
July 17, 2013
5
Texas Instruments-Production Data
Table of Contents
9.2.1
9.2.2
9.2.3
9.2.4
9.2.5
9.2.6
9.2.7
9.2.8
9.2.9
9.2.10
9.3
9.3.1
9.3.2
9.3.3
9.3.4
9.3.5
9.4
9.5
9.6
Channel Assignments .................................................................................................. 578
Priority ........................................................................................................................ 579
Arbitration Size ............................................................................................................ 579
Request Types ............................................................................................................ 579
Channel Configuration ................................................................................................. 580
Transfer Modes ........................................................................................................... 582
Transfer Size and Increment ........................................................................................ 590
Peripheral Interface ..................................................................................................... 590
Software Request ........................................................................................................ 590
Interrupts and Errors .................................................................................................... 591
Initialization and Configuration ..................................................................................... 591
Module Initialization ..................................................................................................... 591
Configuring a Memory-to-Memory Transfer ................................................................... 592
Configuring a Peripheral for Simple Transmit ................................................................ 593
Configuring a Peripheral for Ping-Pong Receive ............................................................ 595
Configuring Channel Assignments ................................................................................ 597
Register Map .............................................................................................................. 597
μDMA Channel Control Structure ................................................................................. 599
μDMA Register Descriptions ........................................................................................ 606
10
General-Purpose Input/Outputs (GPIOs) ........................................................... 640
10.1
10.2
10.2.1
10.2.2
10.2.3
10.2.4
10.2.5
10.2.6
10.3
10.4
10.5
Signal Description ....................................................................................................... 640
Functional Description ................................................................................................. 643
Data Control ............................................................................................................... 645
Interrupt Control .......................................................................................................... 646
Mode Control .............................................................................................................. 647
Commit Control ........................................................................................................... 648
Pad Control ................................................................................................................. 648
Identification ............................................................................................................... 648
Initialization and Configuration ..................................................................................... 648
Register Map .............................................................................................................. 650
Register Descriptions .................................................................................................. 653
11
General-Purpose Timers ...................................................................................... 698
11.1
11.2
11.3
11.3.1
11.3.2
11.3.3
11.3.4
11.3.5
11.3.6
11.3.7
11.4
11.4.1
11.4.2
11.4.3
11.4.4
11.4.5
Block Diagram ............................................................................................................ 699
Signal Description ....................................................................................................... 700
Functional Description ................................................................................................. 702
GPTM Reset Conditions .............................................................................................. 702
Timer Modes ............................................................................................................... 703
Wait-for-Trigger Mode .................................................................................................. 712
Synchronizing GP Timer Blocks ................................................................................... 713
DMA Operation ........................................................................................................... 713
Accessing Concatenated 16/32-Bit GPTM Register Values ............................................ 714
Accessing Concatenated 32/64-Bit Wide GPTM Register Values .................................... 714
Initialization and Configuration ..................................................................................... 716
One-Shot/Periodic Timer Mode .................................................................................... 716
Real-Time Clock (RTC) Mode ...................................................................................... 717
Input Edge-Count Mode ............................................................................................... 717
Input Edge Timing Mode .............................................................................................. 718
PWM Mode ................................................................................................................. 718
6
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
11.5
11.6
Register Map .............................................................................................................. 719
Register Descriptions .................................................................................................. 720
12
Watchdog Timers ................................................................................................. 768
12.1
12.2
12.2.1
12.3
12.4
12.5
Block Diagram ............................................................................................................
Functional Description .................................................................................................
Register Access Timing ...............................................................................................
Initialization and Configuration .....................................................................................
Register Map ..............................................................................................................
Register Descriptions ..................................................................................................
769
769
770
770
770
771
13
Analog-to-Digital Converter (ADC) ..................................................................... 793
13.1
13.2
13.3
13.3.1
13.3.2
13.3.3
13.3.4
13.3.5
13.3.6
13.3.7
13.4
13.4.1
13.4.2
13.5
13.6
Block Diagram ............................................................................................................ 794
Signal Description ....................................................................................................... 795
Functional Description ................................................................................................. 796
Sample Sequencers .................................................................................................... 796
Module Control ............................................................................................................ 797
Hardware Sample Averaging Circuit ............................................................................. 801
Analog-to-Digital Converter .......................................................................................... 801
Differential Sampling ................................................................................................... 804
Internal Temperature Sensor ........................................................................................ 806
Digital Comparator Unit ............................................................................................... 807
Initialization and Configuration ..................................................................................... 811
Module Initialization ..................................................................................................... 811
Sample Sequencer Configuration ................................................................................. 812
Register Map .............................................................................................................. 812
Register Descriptions .................................................................................................. 814
14
Universal Asynchronous Receivers/Transmitters (UARTs) ............................. 892
14.1
Block Diagram ............................................................................................................
14.2
Signal Description .......................................................................................................
14.3
Functional Description .................................................................................................
14.3.1 Transmit/Receive Logic ...............................................................................................
14.3.2 Baud-Rate Generation .................................................................................................
14.3.3 Data Transmission ......................................................................................................
14.3.4 Serial IR (SIR) .............................................................................................................
14.3.5 ISO 7816 Support .......................................................................................................
14.3.6 Modem Handshake Support .........................................................................................
14.3.7 9-Bit UART Mode ........................................................................................................
14.3.8 FIFO Operation ...........................................................................................................
14.3.9 Interrupts ....................................................................................................................
14.3.10 Loopback Operation ....................................................................................................
14.3.11 DMA Operation ...........................................................................................................
14.4
Initialization and Configuration .....................................................................................
14.5
Register Map ..............................................................................................................
14.6
Register Descriptions ..................................................................................................
893
893
894
895
895
896
896
897
898
899
900
900
901
901
902
903
904
15
Synchronous Serial Interface (SSI) .................................................................... 952
15.1
15.2
15.3
Block Diagram ............................................................................................................ 953
Signal Description ....................................................................................................... 953
Functional Description ................................................................................................. 954
July 17, 2013
7
Texas Instruments-Production Data
Table of Contents
15.3.1
15.3.2
15.3.3
15.3.4
15.3.5
15.4
15.5
15.6
Bit Rate Generation .....................................................................................................
FIFO Operation ...........................................................................................................
Interrupts ....................................................................................................................
Frame Formats ...........................................................................................................
DMA Operation ...........................................................................................................
Initialization and Configuration .....................................................................................
Register Map ..............................................................................................................
Register Descriptions ..................................................................................................
955
955
955
956
964
964
966
967
16
Inter-Integrated Circuit (I2C) Interface ................................................................ 996
16.1
16.2
16.3
16.3.1
16.3.2
16.3.3
16.3.4
16.3.5
16.4
16.5
16.6
16.7
16.8
Block Diagram ............................................................................................................ 997
Signal Description ....................................................................................................... 997
Functional Description ................................................................................................. 998
I2C Bus Functional Overview ........................................................................................ 998
Available Speed Modes ............................................................................................. 1003
Interrupts .................................................................................................................. 1005
Loopback Operation .................................................................................................. 1006
Command Sequence Flow Charts .............................................................................. 1006
Initialization and Configuration .................................................................................... 1014
Register Map ............................................................................................................ 1016
Register Descriptions (I2C Master) .............................................................................. 1017
Register Descriptions (I2C Slave) ............................................................................... 1034
Register Descriptions (I2C Status and Control) ............................................................ 1044
17
Controller Area Network (CAN) Module ........................................................... 1047
17.1
Block Diagram ........................................................................................................... 1048
17.2
Signal Description ..................................................................................................... 1048
17.3
Functional Description ............................................................................................... 1049
17.3.1 Initialization ............................................................................................................... 1050
17.3.2 Operation .................................................................................................................. 1051
17.3.3 Transmitting Message Objects ................................................................................... 1052
17.3.4 Configuring a Transmit Message Object ...................................................................... 1052
17.3.5 Updating a Transmit Message Object ......................................................................... 1053
17.3.6 Accepting Received Message Objects ........................................................................ 1054
17.3.7 Receiving a Data Frame ............................................................................................ 1054
17.3.8 Receiving a Remote Frame ........................................................................................ 1054
17.3.9 Receive/Transmit Priority ........................................................................................... 1055
17.3.10 Configuring a Receive Message Object ...................................................................... 1055
17.3.11 Handling of Received Message Objects ...................................................................... 1056
17.3.12 Handling of Interrupts ................................................................................................ 1058
17.3.13 Test Mode ................................................................................................................. 1059
17.3.14 Bit Timing Configuration Error Considerations ............................................................. 1061
17.3.15 Bit Time and Bit Rate ................................................................................................. 1061
17.3.16 Calculating the Bit Timing Parameters ........................................................................ 1063
17.4
Register Map ............................................................................................................ 1066
17.5
CAN Register Descriptions ......................................................................................... 1067
18
Analog Comparators .......................................................................................... 1098
18.1
18.2
Block Diagram ........................................................................................................... 1099
Signal Description ..................................................................................................... 1099
8
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
18.3
18.3.1
18.4
18.5
18.6
Functional Description ...............................................................................................
Internal Reference Programming ................................................................................
Initialization and Configuration ....................................................................................
Register Map ............................................................................................................
Register Descriptions .................................................................................................
1100
1101
1103
1104
1104
19
Pulse Width Modulator (PWM) .......................................................................... 1114
19.1
19.2
19.3
19.3.1
19.3.2
19.3.3
19.3.4
19.3.5
19.3.6
19.3.7
19.3.8
19.3.9
19.4
19.5
19.6
Block Diagram ........................................................................................................... 1115
Signal Description ..................................................................................................... 1117
Functional Description ............................................................................................... 1118
Clock Configuration ................................................................................................... 1118
PWM Timer ............................................................................................................... 1118
PWM Comparators .................................................................................................... 1119
PWM Signal Generator .............................................................................................. 1120
Dead-Band Generator ............................................................................................... 1121
Interrupt/ADC-Trigger Selector ................................................................................... 1121
Synchronization Methods .......................................................................................... 1122
Fault Conditions ........................................................................................................ 1123
Output Control Block .................................................................................................. 1123
Initialization and Configuration .................................................................................... 1124
Register Map ............................................................................................................ 1125
Register Descriptions ................................................................................................. 1128
20
Quadrature Encoder Interface (QEI) ................................................................. 1193
20.1
20.2
20.3
20.4
20.5
20.6
Block Diagram ...........................................................................................................
Signal Description .....................................................................................................
Functional Description ...............................................................................................
Initialization and Configuration ....................................................................................
Register Map ............................................................................................................
Register Descriptions .................................................................................................
21
Pin Diagram ........................................................................................................ 1216
1193
1195
1196
1198
1199
1199
22
Signal Tables ...................................................................................................... 1217
22.1
22.2
22.3
22.4
22.5
22.6
Signals by Pin Number ..............................................................................................
Signals by Signal Name .............................................................................................
Signals by Function, Except for GPIO .........................................................................
GPIO Pins and Alternate Functions ............................................................................
Possible Pin Assignments for Alternate Functions .......................................................
Connections for Unused Signals .................................................................................
1218
1228
1238
1247
1249
1252
23
Electrical Characteristics .................................................................................. 1254
23.1
23.2
23.3
23.4
23.5
23.6
23.6.1
23.6.2
23.6.3
23.6.4
Maximum Ratings ......................................................................................................
Operating Characteristics ...........................................................................................
Recommended Operating Conditions .........................................................................
Load Conditions ........................................................................................................
JTAG and Boundary Scan ..........................................................................................
Power and Brown-Out ...............................................................................................
VDDA Levels ............................................................................................................
VDD Levels ...............................................................................................................
VDDC Levels ............................................................................................................
VDD Glitches ............................................................................................................
July 17, 2013
1254
1255
1256
1258
1259
1261
1261
1262
1263
1264
9
Texas Instruments-Production Data
Table of Contents
23.6.5 VDD Droop Response ............................................................................................... 1264
23.7
Reset ........................................................................................................................ 1266
23.8
On-Chip Low Drop-Out (LDO) Regulator ..................................................................... 1268
23.9
Clocks ...................................................................................................................... 1269
23.9.1 PLL Specifications ..................................................................................................... 1269
23.9.2 PIOSC Specifications ................................................................................................ 1270
23.9.3 Low-Frequency Internal Oscillator (LFIOSC) Specifications .......................................... 1270
23.9.4 Hibernation Clock Source Specifications ..................................................................... 1270
23.9.5 Main Oscillator Specifications ..................................................................................... 1271
23.9.6 System Clock Specification with ADC Operation .......................................................... 1274
23.10 Sleep Modes ............................................................................................................. 1275
23.11 Hibernation Module ................................................................................................... 1277
23.12 Flash Memory and EEPROM ..................................................................................... 1278
23.13 Input/Output Pin Characteristics ................................................................................. 1279
23.13.1 GPIO Module Characteristics ..................................................................................... 1279
23.13.2 Types of I/O Pins and ESD Protection ......................................................................... 1279
23.14 Analog-to-Digital Converter (ADC) .............................................................................. 1283
23.15 Synchronous Serial Interface (SSI) ............................................................................. 1287
23.16 Inter-Integrated Circuit (I2C) Interface ......................................................................... 1290
23.17 Analog Comparator ................................................................................................... 1291
23.18 Current Consumption ................................................................................................. 1293
A
Package Information .......................................................................................... 1296
A.1
A.2
A.3
Orderable Devices ..................................................................................................... 1296
Part Markings ............................................................................................................ 1297
Packaging Diagram ................................................................................................... 1298
10
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
List of Figures
Figure 1-1.
Figure 2-1.
Figure 2-2.
Figure 2-3.
Figure 2-4.
Figure 2-5.
Figure 2-6.
Figure 2-7.
Figure 3-1.
Figure 3-2.
Figure 4-1.
Figure 4-2.
Figure 4-3.
Figure 4-4.
Figure 4-5.
Figure 5-1.
Figure 5-2.
Figure 5-3.
Figure 5-4.
Figure 5-5.
Figure 5-6.
Figure 7-1.
Figure 7-2.
Figure 7-3.
Figure 7-4.
Figure 8-1.
Figure 8-2.
Figure 9-1.
Figure 9-2.
Figure 9-3.
Figure 9-4.
Figure 9-5.
Figure 9-6.
Figure 10-1.
Figure 10-2.
Figure 10-3.
Figure 10-4.
Figure 11-1.
Figure 11-2.
Figure 11-3.
Figure 11-4.
Figure 11-5.
Figure 11-6.
Figure 11-7.
Figure 11-8.
Tiva™ TM4C123BE6PZ Microcontroller High-Level Block Diagram .......................... 41
CPU Block Diagram ............................................................................................. 63
TPIU Block Diagram ............................................................................................ 64
Cortex-M4F Register Set ...................................................................................... 67
Bit-Band Mapping ................................................................................................ 91
Data Storage ....................................................................................................... 92
Vector Table ........................................................................................................ 99
Exception Stack Frame ...................................................................................... 102
SRD Use Example ............................................................................................. 120
FPU Register Bank ............................................................................................ 123
JTAG Module Block Diagram .............................................................................. 193
Test Access Port State Machine ......................................................................... 196
IDCODE Register Format ................................................................................... 202
BYPASS Register Format ................................................................................... 202
Boundary Scan Register Format ......................................................................... 203
Basic RST Configuration .................................................................................... 207
External Circuitry to Extend Power-On Reset ....................................................... 207
Reset Circuit Controlled by Switch ...................................................................... 208
Power Architecture ............................................................................................ 211
Main Clock Tree ................................................................................................ 214
Module Clock Selection ...................................................................................... 220
Hibernation Module Block Diagram ..................................................................... 487
Using a Crystal as the Hibernation Clock Source with a Single Battery Source ...... 489
Using a Dedicated Oscillator as the Hibernation Clock Source with VDD3ON
Mode ................................................................................................................ 490
Using a Regulator for Both VDD and VBAT ............................................................ 491
Internal Memory Block Diagram .......................................................................... 517
EEPROM Block Diagram ................................................................................... 518
μDMA Block Diagram ......................................................................................... 577
Example of Ping-Pong μDMA Transaction ........................................................... 583
Memory Scatter-Gather, Setup and Configuration ................................................ 585
Memory Scatter-Gather, μDMA Copy Sequence .................................................. 586
Peripheral Scatter-Gather, Setup and Configuration ............................................. 588
Peripheral Scatter-Gather, μDMA Copy Sequence ............................................... 589
Digital I/O Pads ................................................................................................. 644
Analog/Digital I/O Pads ...................................................................................... 645
GPIODATA Write Example ................................................................................. 646
GPIODATA Read Example ................................................................................. 646
GPTM Module Block Diagram ............................................................................ 699
Reading the RTC Value ...................................................................................... 706
Input Edge-Count Mode Example, Counting Down ............................................... 708
16-Bit Input Edge-Time Mode Example ............................................................... 709
16-Bit PWM Mode Example ................................................................................ 711
CCP Output, GPTMTnMATCHR > GPTMTnILR ................................................... 711
CCP Output, GPTMTnMATCHR = GPTMTnILR ................................................... 712
CCP Output, GPTMTnILR > GPTMTnMATCHR ................................................... 712
July 17, 2013
11
Texas Instruments-Production Data
Table of Contents
Figure 11-9.
Figure 12-1.
Figure 13-1.
Figure 13-2.
Figure 13-3.
Figure 13-4.
Figure 13-5.
Figure 13-6.
Figure 13-7.
Figure 13-8.
Figure 13-9.
Figure 13-10.
Figure 13-11.
Figure 13-12.
Figure 13-13.
Figure 13-14.
Figure 14-1.
Figure 14-2.
Figure 14-3.
Figure 15-1.
Figure 15-2.
Figure 15-3.
Figure 15-4.
Figure 15-5.
Figure 15-6.
Figure 15-7.
Figure 15-8.
Figure 15-9.
Figure 15-10.
Figure 15-11.
Figure 15-12.
Figure 16-1.
Figure 16-2.
Figure 16-3.
Figure 16-4.
Figure 16-5.
Figure 16-6.
Figure 16-7.
Figure 16-8.
Figure 16-9.
Figure 16-10.
Figure 16-11.
Figure 16-12.
Figure 16-13.
Figure 16-14.
Figure 16-15.
Figure 17-1.
Figure 17-2.
Timer Daisy Chain ............................................................................................. 713
WDT Module Block Diagram .............................................................................. 769
Implementation of Two ADC Blocks .................................................................... 794
ADC Module Block Diagram ............................................................................... 795
ADC Sample Phases ......................................................................................... 799
Doubling the ADC Sample Rate .......................................................................... 799
Skewed Sampling .............................................................................................. 800
Sample Averaging Example ............................................................................... 801
ADC Input Equivalency Diagram ......................................................................... 802
ADC Voltage Reference ..................................................................................... 803
ADC Conversion Result ..................................................................................... 804
Differential Voltage Representation ..................................................................... 806
Internal Temperature Sensor Characteristic ......................................................... 807
Low-Band Operation (CIC=0x0 and/or CTC=0x0) ................................................ 809
Mid-Band Operation (CIC=0x1 and/or CTC=0x1) ................................................. 810
High-Band Operation (CIC=0x3 and/or CTC=0x3) ................................................ 811
UART Module Block Diagram ............................................................................. 893
UART Character Frame ..................................................................................... 895
IrDA Data Modulation ......................................................................................... 897
SSI Module Block Diagram ................................................................................. 953
TI Synchronous Serial Frame Format (Single Transfer) ........................................ 957
TI Synchronous Serial Frame Format (Continuous Transfer) ................................ 958
Freescale SPI Format (Single Transfer) with SPO=0 and SPH=0 .......................... 958
Freescale SPI Format (Continuous Transfer) with SPO=0 and SPH=0 .................. 959
Freescale SPI Frame Format with SPO=0 and SPH=1 ......................................... 960
Freescale SPI Frame Format (Single Transfer) with SPO=1 and SPH=0 ............... 960
Freescale SPI Frame Format (Continuous Transfer) with SPO=1 and SPH=0 ........ 961
Freescale SPI Frame Format with SPO=1 and SPH=1 ......................................... 962
MICROWIRE Frame Format (Single Frame) ........................................................ 962
MICROWIRE Frame Format (Continuous Transfer) ............................................. 963
MICROWIRE Frame Format, SSIFss Input Setup and Hold Requirements ............ 964
I2C Block Diagram ............................................................................................. 997
I2C Bus Configuration ........................................................................................ 998
START and STOP Conditions ............................................................................. 999
Complete Data Transfer with a 7-Bit Address ....................................................... 999
R/S Bit in First Byte .......................................................................................... 1000
Data Validity During Bit Transfer on the I2C Bus ................................................. 1000
High-Speed Data Format .................................................................................. 1005
Master Single TRANSMIT ................................................................................ 1007
Master Single RECEIVE ................................................................................... 1008
Master TRANSMIT of Multiple Data Bytes ......................................................... 1009
Master RECEIVE of Multiple Data Bytes ............................................................ 1010
Master RECEIVE with Repeated START after Master TRANSMIT ....................... 1011
Master TRANSMIT with Repeated START after Master RECEIVE ....................... 1012
Standard High Speed Mode Master Transmit ..................................................... 1013
Slave Command Sequence .............................................................................. 1014
CAN Controller Block Diagram .......................................................................... 1048
CAN Data/Remote Frame ................................................................................. 1050
12
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Figure 17-3.
Figure 17-4.
Figure 18-1.
Figure 18-2.
Figure 18-3.
Figure 19-1.
Figure 19-2.
Figure 19-3.
Figure 19-4.
Figure 19-5.
Figure 19-6.
Figure 20-1.
Figure 20-2.
Figure 20-3.
Figure 21-1.
Figure 23-1.
Figure 23-2.
Figure 23-3.
Figure 23-4.
Figure 23-5.
Figure 23-6.
Figure 23-7.
Figure 23-8.
Figure 23-9.
Figure 23-10.
Figure 23-11.
Figure 23-12.
Figure 23-13.
Figure 23-14.
Figure 23-15.
Figure 23-16.
Figure 23-17.
Figure 23-18.
Figure 23-19.
Figure 23-20.
Figure 23-21.
Figure 23-22.
Figure 23-23.
Figure 23-24.
Figure A-1.
Figure A-2.
Message Objects in a FIFO Buffer .................................................................... 1058
CAN Bit Time ................................................................................................... 1062
Analog Comparator Module Block Diagram ....................................................... 1099
Structure of Comparator Unit ............................................................................ 1100
Comparator Internal Reference Structure .......................................................... 1101
PWM Module Diagram ..................................................................................... 1116
PWM Generator Block Diagram ........................................................................ 1116
PWM Count-Down Mode .................................................................................. 1120
PWM Count-Up/Down Mode ............................................................................. 1120
PWM Generation Example In Count-Up/Down Mode .......................................... 1121
PWM Dead-Band Generator ............................................................................. 1121
QEI Block Diagram .......................................................................................... 1194
QEI Input Signal Logic ...................................................................................... 1195
Quadrature Encoder and Velocity Predivider Operation ...................................... 1197
100-Pin LQFP Package Pin Diagram ................................................................ 1216
Load Conditions ............................................................................................... 1258
JTAG Test Clock Input Timing ........................................................................... 1259
JTAG Test Access Port (TAP) Timing ................................................................ 1260
Power Assertions versus VDDA Levels ............................................................. 1262
Power and Brown-Out Assertions versus VDD Levels ........................................ 1263
POK assertion vs VDDC ................................................................................... 1264
POR-BOR0-BOR1 VDD Glitch Response .......................................................... 1264
POR-BOR0-BOR1 VDD Droop Response ......................................................... 1265
Digital Power-On Reset Timing ......................................................................... 1266
Brown-Out Reset Timing .................................................................................. 1266
External Reset Timing (RST) ............................................................................ 1267
Software Reset Timing ..................................................................................... 1267
Watchdog Reset Timing ................................................................................... 1267
MOSC Failure Reset Timing ............................................................................. 1267
Hibernation Module Timing ............................................................................... 1277
ESD Protection on Fail-Safe Pins ...................................................................... 1280
ESD Protection on Non-Fail-Safe Pins .............................................................. 1281
ADC External Reference Filtering ..................................................................... 1285
ADC Input Equivalency Diagram ....................................................................... 1286
SSI Timing for TI Frame Format (FRF=01), Single Transfer Timing
Measurement .................................................................................................. 1288
SSI Timing for MICROWIRE Frame Format (FRF=10), Single Transfer ............... 1288
Master Mode SSI Timing for SPI Frame Format (FRF=00), with SPH=1 .............. 1289
Slave Mode SSI Timing for SPI Frame Format (FRF=00), with SPH=1 ................ 1289
I2C Timing ....................................................................................................... 1290
Key to Part Numbers ........................................................................................ 1296
TM4C123BE6PZ 100-Pin LQFP Package Diagram ............................................ 1298
July 17, 2013
13
Texas Instruments-Production Data
Table of Contents
List of Tables
Table 1.
Table 2.
Table 1-1.
Table 2-1.
Table 2-2.
Table 2-3.
Table 2-4.
Table 2-5.
Table 2-6.
Table 2-7.
Table 2-8.
Table 2-9.
Table 2-10.
Table 2-11.
Table 2-12.
Table 2-13.
Table 3-1.
Table 3-2.
Table 3-3.
Table 3-4.
Table 3-5.
Table 3-6.
Table 3-7.
Table 3-8.
Table 3-9.
Table 3-10.
Table 4-1.
Table 4-2.
Table 4-3.
Table 5-1.
Table 5-2.
Table 5-3.
Table 5-4.
Table 5-5.
Table 5-6.
Table 5-7.
Table 5-8.
Table 6-1.
Table 7-1.
Table 7-2.
Table 7-3.
Table 7-4.
Table 7-5.
Table 8-1.
Table 8-2.
Table 8-3.
Revision History .................................................................................................. 34
Documentation Conventions ................................................................................ 37
TM4C123BE6PZ Microcontroller Features ............................................................ 40
Summary of Processor Mode, Privilege Level, and Stack Use ................................ 66
Processor Register Map ....................................................................................... 67
PSR Register Combinations ................................................................................. 73
Memory Map ....................................................................................................... 84
Memory Access Behavior ..................................................................................... 88
SRAM Memory Bit-Banding Regions .................................................................... 90
Peripheral Memory Bit-Banding Regions ............................................................... 90
Exception Types .................................................................................................. 95
Interrupts ............................................................................................................ 96
Exception Return Behavior ................................................................................. 103
Faults ............................................................................................................... 104
Fault Status and Fault Address Registers ............................................................ 105
Cortex-M4F Instruction Summary ....................................................................... 107
Core Peripheral Register Regions ....................................................................... 114
Memory Attributes Summary .............................................................................. 118
TEX, S, C, and B Bit Field Encoding ................................................................... 120
Cache Policy for Memory Attribute Encoding ....................................................... 121
AP Bit Field Encoding ........................................................................................ 121
Memory Region Attributes for Tiva™ C Series Microcontrollers ............................. 122
QNaN and SNaN Handling ................................................................................. 125
Peripherals Register Map ................................................................................... 126
Interrupt Priority Levels ...................................................................................... 156
Example SIZE Field Values ................................................................................ 184
JTAG_SWD_SWO Signals (100LQFP) ................................................................ 193
JTAG Port Pins State after Power-On Reset or RST assertion .............................. 194
JTAG Instruction Register Commands ................................................................. 200
System Control & Clocks Signals (100LQFP) ...................................................... 204
Reset Sources ................................................................................................... 205
Clock Source Options ........................................................................................ 212
Possible System Clock Frequencies Using the SYSDIV Field ............................... 215
Examples of Possible System Clock Frequencies Using the SYSDIV2 Field .......... 215
Examples of Possible System Clock Frequencies with DIV400=1 ......................... 216
System Control Register Map ............................................................................. 223
RCC2 Fields that Override RCC Fields ............................................................... 251
System Exception Register Map ......................................................................... 478
Hibernate Signals (100LQFP) ............................................................................. 487
Counter Behavior with a TRIM Value of 0x8003 ................................................... 493
Counter Behavior with a TRIM Value of 0x7FFC .................................................. 494
Hibernation Module Clock Operation ................................................................... 497
Hibernation Module Register Map ....................................................................... 498
Flash Memory Protection Policy Combinations .................................................... 522
User-Programmable Flash Memory Resident Registers ....................................... 526
Flash Register Map ............................................................................................ 532
14
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Table 9-1.
Table 9-2.
Table 9-3.
Table 9-4.
Table 9-5.
Table 9-6.
Table 9-7.
Table 9-8.
Table 9-9.
Table 9-10.
Table 9-11.
Table 9-12.
μDMA Channel Assignments .............................................................................. 578
Request Type Support ....................................................................................... 580
Control Structure Memory Map ........................................................................... 581
Channel Control Structure .................................................................................. 581
μDMA Read Example: 8-Bit Peripheral ................................................................ 590
μDMA Interrupt Assignments .............................................................................. 591
Channel Control Structure Offsets for Channel 30 ................................................ 592
Channel Control Word Configuration for Memory Transfer Example ...................... 592
Channel Control Structure Offsets for Channel 7 .................................................. 593
Channel Control Word Configuration for Peripheral Transmit Example .................. 594
Primary and Alternate Channel Control Structure Offsets for Channel 8 ................. 595
Channel Control Word Configuration for Peripheral Ping-Pong Receive
Example ............................................................................................................ 596
Table 9-13.
μDMA Register Map .......................................................................................... 598
Table 10-1.
GPIO Pins With Non-Zero Reset Values .............................................................. 641
Table 10-2.
GPIO Pins and Alternate Functions (100LQFP) ................................................... 641
Table 10-3.
GPIO Pad Configuration Examples ..................................................................... 649
Table 10-4.
GPIO Interrupt Configuration Example ................................................................ 650
Table 10-5.
GPIO Pins With Non-Zero Reset Values .............................................................. 651
Table 10-6.
GPIO Register Map ........................................................................................... 651
Table 10-7.
GPIO Pins With Non-Zero Reset Values .............................................................. 664
Table 10-8.
GPIO Pins With Non-Zero Reset Values .............................................................. 670
Table 10-9.
GPIO Pins With Non-Zero Reset Values .............................................................. 672
Table 10-10. GPIO Pins With Non-Zero Reset Values .............................................................. 675
Table 10-11. GPIO Pins With Non-Zero Reset Values .............................................................. 682
Table 11-1.
Available CCP Pins ............................................................................................ 700
Table 11-2.
General-Purpose Timers Signals (100LQFP) ....................................................... 700
Table 11-3.
General-Purpose Timer Capabilities .................................................................... 702
Table 11-4.
Counter Values When the Timer is Enabled in Periodic or One-Shot Modes .......... 703
Table 11-5.
16-Bit Timer With Prescaler Configurations ......................................................... 705
Table 11-6.
32-Bit Timer (configured in 32/64-bit mode) With Prescaler Configurations ............ 705
Table 11-7.
Counter Values When the Timer is Enabled in RTC Mode .................................... 705
Table 11-8.
Counter Values When the Timer is Enabled in Input Edge-Count Mode ................. 707
Table 11-9.
Counter Values When the Timer is Enabled in Input Event-Count Mode ................ 708
Table 11-10. Counter Values When the Timer is Enabled in PWM Mode ................................... 710
Table 11-11. Timeout Actions for GPTM Modes ...................................................................... 713
Table 11-12. Timers Register Map .......................................................................................... 720
Table 12-1.
Watchdog Timers Register Map .......................................................................... 771
Table 13-1.
ADC Signals (100LQFP) .................................................................................... 795
Table 13-2.
Samples and FIFO Depth of Sequencers ............................................................ 797
Table 13-3.
Differential Sampling Pairs ................................................................................. 804
Table 13-4.
ADC Register Map ............................................................................................. 812
Table 14-1.
UART Signals (100LQFP) .................................................................................. 894
Table 14-2.
Flow Control Mode ............................................................................................. 899
Table 14-3.
UART Register Map ........................................................................................... 903
Table 15-1.
SSI Signals (100LQFP) ...................................................................................... 954
Table 15-2.
SSI Register Map .............................................................................................. 966
Table 16-1.
I2C Signals (100LQFP) ...................................................................................... 997
July 17, 2013
15
Texas Instruments-Production Data
Table of Contents
Table 16-2.
Table 16-3.
Table 16-4.
Table 16-5.
Table 17-1.
Table 17-2.
Table 17-3.
Table 17-4.
Table 17-5.
Table 18-1.
Table 18-2.
Table 18-3.
Table 18-4.
Table 18-5.
Table 19-1.
Table 19-2.
Table 20-1.
Table 20-2.
Table 22-1.
Table 22-2.
Table 22-3.
Table 22-4.
Table 22-5.
Table 22-6.
Table 22-7.
Table 23-1.
Table 23-2.
Table 23-3.
Table 23-4.
Table 23-5.
Table 23-6.
Table 23-7.
Table 23-8.
Table 23-9.
Table 23-10.
Table 23-11.
Table 23-12.
Table 23-13.
Table 23-14.
Table 23-15.
Table 23-16.
Table 23-17.
Table 23-18.
Table 23-19.
Table 23-20.
Table 23-21.
Examples of I2C Master Timer Period versus Speed Mode ................................. 1003
Examples of I2C Master Timer Period in High-Speed Mode ................................ 1004
Inter-Integrated Circuit (I2C) Interface Register Map ........................................... 1016
Write Field Decoding for I2CMCS[3:0] Field ....................................................... 1022
Controller Area Network Signals (100LQFP) ...................................................... 1049
Message Object Configurations ........................................................................ 1055
CAN Protocol Ranges ...................................................................................... 1062
CANBIT Register Values .................................................................................. 1062
CAN Register Map ........................................................................................... 1066
Analog Comparators Signals (100LQFP) ........................................................... 1099
Internal Reference Voltage and ACREFCTL Field Values ................................... 1101
Analog Comparator Voltage Reference Characteristics, VDDA = 3.3V, EN= 1, and
RNG = 0 .......................................................................................................... 1102
Analog Comparator Voltage Reference Characteristics, VDDA = 3.3V, EN= 1, and
RNG = 1 .......................................................................................................... 1103
Analog Comparators Register Map ................................................................... 1104
PWM Signals (100LQFP) ................................................................................. 1117
PWM Register Map .......................................................................................... 1125
QEI Signals (100LQFP) .................................................................................... 1195
QEI Register Map ............................................................................................ 1199
GPIO Pins With Default Alternate Functions ...................................................... 1217
Signals by Pin Number ..................................................................................... 1218
Signals by Signal Name ................................................................................... 1228
Signals by Function, Except for GPIO ............................................................... 1238
GPIO Pins and Alternate Functions ................................................................... 1247
Possible Pin Assignments for Alternate Functions .............................................. 1249
Connections for Unused Signals (100-Pin LQFP) ............................................... 1253
Maximum Ratings ............................................................................................ 1254
ESD Absolute Maximum Ratings ...................................................................... 1254
Temperature Characteristics ............................................................................. 1255
Thermal Characteristics ................................................................................... 1255
Recommended DC Operating Conditions .......................................................... 1256
Recommended GPIO Pad Operating Conditions ................................................ 1256
GPIO Current Restrictions ................................................................................ 1256
GPIO Package Side Assignments ..................................................................... 1257
JTAG Characteristics ....................................................................................... 1259
Power-On and Brown-Out Levels ...................................................................... 1261
Reset Characteristics ....................................................................................... 1266
LDO Regulator Characteristics ......................................................................... 1268
Phase Locked Loop (PLL) Characteristics ......................................................... 1269
Actual PLL Frequency ...................................................................................... 1269
PIOSC Clock Characteristics ............................................................................ 1270
Low-Frequency internal Oscillator Characteristics .............................................. 1270
Hibernation Oscillator Input Characteristics ........................................................ 1270
Main Oscillator Input Characteristics ................................................................. 1271
Crystal Parameters .......................................................................................... 1272
Supported MOSC Crystal Frequencies .............................................................. 1273
System Clock Characteristics with ADC Operation ............................................. 1274
16
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Table 23-22.
Table 23-23.
Table 23-24.
Table 23-25.
Table 23-26.
Table 23-27.
Table 23-28.
Table 23-29.
Table 23-30.
Table 23-31.
Table 23-32.
Table 23-33.
Table 23-34.
Table 23-35.
Table 23-36.
Table 23-37.
Sleep Modes AC Characteristics ....................................................................... 1275
Time to Wake with Respect to Low-Power Modes .............................................. 1275
Hibernation Module Battery Characteristics ....................................................... 1277
Hibernation Module AC Characteristics ............................................................. 1277
Flash Memory Characteristics ........................................................................... 1278
EEPROM Characteristics ................................................................................. 1278
GPIO Module Characteristics ............................................................................ 1279
Pad Voltage/Current Characteristics for Fail-Safe Pins ....................................... 1280
Fail-Safe GPIOs that Require an External Pull-up .............................................. 1281
Non-Fail-Safe I/O Pad Voltage/Current Characteristics ....................................... 1281
ADC Electrical Characteristics .......................................................................... 1283
SSI Characteristics .......................................................................................... 1287
I2C Characteristics ........................................................................................... 1290
Analog Comparator Characteristics ................................................................... 1291
Analog Comparator Voltage Reference Characteristics ...................................... 1291
Analog Comparator Voltage Reference Characteristics, VDDA = 3.3V, EN= 1, and
RNG = 0 .......................................................................................................... 1291
Table 23-38. Analog Comparator Voltage Reference Characteristics, VDDA = 3.3V, EN= 1, and
RNG = 1 .......................................................................................................... 1292
Table 23-39. Current Consumption ....................................................................................... 1293
Table A-1.
Orderable Part Numbers .................................................................................. 1296
July 17, 2013
17
Texas Instruments-Production Data
Table of Contents
List of Registers
The Cortex-M4F Processor ........................................................................................................... 61
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Cortex General-Purpose Register 0 (R0) ........................................................................... 69
Cortex General-Purpose Register 1 (R1) ........................................................................... 69
Cortex General-Purpose Register 2 (R2) ........................................................................... 69
Cortex General-Purpose Register 3 (R3) ........................................................................... 69
Cortex General-Purpose Register 4 (R4) ........................................................................... 69
Cortex General-Purpose Register 5 (R5) ........................................................................... 69
Cortex General-Purpose Register 6 (R6) ........................................................................... 69
Cortex General-Purpose Register 7 (R7) ........................................................................... 69
Cortex General-Purpose Register 8 (R8) ........................................................................... 69
Cortex General-Purpose Register 9 (R9) ........................................................................... 69
Cortex General-Purpose Register 10 (R10) ....................................................................... 69
Cortex General-Purpose Register 11 (R11) ........................................................................ 69
Cortex General-Purpose Register 12 (R12) ....................................................................... 69
Stack Pointer (SP) ........................................................................................................... 70
Link Register (LR) ............................................................................................................ 71
Program Counter (PC) ..................................................................................................... 72
Program Status Register (PSR) ........................................................................................ 73
Priority Mask Register (PRIMASK) .................................................................................... 77
Fault Mask Register (FAULTMASK) .................................................................................. 78
Base Priority Mask Register (BASEPRI) ............................................................................ 79
Control Register (CONTROL) ........................................................................................... 80
Floating-Point Status Control (FPSC) ................................................................................ 82
Cortex-M4 Peripherals ................................................................................................................. 114
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
SysTick Control and Status Register (STCTRL), offset 0x010 ........................................... 130
SysTick Reload Value Register (STRELOAD), offset 0x014 .............................................. 132
SysTick Current Value Register (STCURRENT), offset 0x018 ........................................... 133
Interrupt 0-31 Set Enable (EN0), offset 0x100 .................................................................. 134
Interrupt 32-63 Set Enable (EN1), offset 0x104 ................................................................ 134
Interrupt 64-95 Set Enable (EN2), offset 0x108 ................................................................ 134
Interrupt 96-127 Set Enable (EN3), offset 0x10C ............................................................. 134
Interrupt 128-138 Set Enable (EN4), offset 0x110 ............................................................ 135
Interrupt 0-31 Clear Enable (DIS0), offset 0x180 .............................................................. 136
Interrupt 32-63 Clear Enable (DIS1), offset 0x184 ............................................................ 136
Interrupt 64-95 Clear Enable (DIS2), offset 0x188 ............................................................ 136
Interrupt 96-127 Clear Enable (DIS3), offset 0x18C .......................................................... 136
Interrupt 128-138 Clear Enable (DIS4), offset 0x190 ........................................................ 137
Interrupt 0-31 Set Pending (PEND0), offset 0x200 ........................................................... 138
Interrupt 32-63 Set Pending (PEND1), offset 0x204 ......................................................... 138
Interrupt 64-95 Set Pending (PEND2), offset 0x208 ......................................................... 138
Interrupt 96-127 Set Pending (PEND3), offset 0x20C ....................................................... 138
Interrupt 128-138 Set Pending (PEND4), offset 0x210 ...................................................... 139
Interrupt 0-31 Clear Pending (UNPEND0), offset 0x280 ................................................... 140
Interrupt 32-63 Clear Pending (UNPEND1), offset 0x284 .................................................. 140
Interrupt 64-95 Clear Pending (UNPEND2), offset 0x288 .................................................. 140
18
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
Register 31:
Register 32:
Register 33:
Register 34:
Register 35:
Register 36:
Register 37:
Register 38:
Register 39:
Register 40:
Register 41:
Register 42:
Register 43:
Register 44:
Register 45:
Register 46:
Register 47:
Register 48:
Register 49:
Register 50:
Register 51:
Register 52:
Register 53:
Register 54:
Register 55:
Register 56:
Register 57:
Register 58:
Register 59:
Register 60:
Register 61:
Register 62:
Register 63:
Register 64:
Register 65:
Register 66:
Register 67:
Register 68:
Register 69:
Interrupt 96-127 Clear Pending (UNPEND3), offset 0x28C ............................................... 140
Interrupt 128-138 Clear Pending (UNPEND4), offset 0x290 .............................................. 141
Interrupt 0-31 Active Bit (ACTIVE0), offset 0x300 ............................................................. 142
Interrupt 32-63 Active Bit (ACTIVE1), offset 0x304 ........................................................... 142
Interrupt 64-95 Active Bit (ACTIVE2), offset 0x308 ........................................................... 142
Interrupt 96-127 Active Bit (ACTIVE3), offset 0x30C ........................................................ 142
Interrupt 128-138 Active Bit (ACTIVE4), offset 0x310 ....................................................... 143
Interrupt 0-3 Priority (PRI0), offset 0x400 ......................................................................... 144
Interrupt 4-7 Priority (PRI1), offset 0x404 ......................................................................... 144
Interrupt 8-11 Priority (PRI2), offset 0x408 ....................................................................... 144
Interrupt 12-15 Priority (PRI3), offset 0x40C .................................................................... 144
Interrupt 16-19 Priority (PRI4), offset 0x410 ..................................................................... 144
Interrupt 20-23 Priority (PRI5), offset 0x414 ..................................................................... 144
Interrupt 24-27 Priority (PRI6), offset 0x418 ..................................................................... 144
Interrupt 28-31 Priority (PRI7), offset 0x41C .................................................................... 144
Interrupt 32-35 Priority (PRI8), offset 0x420 ..................................................................... 144
Interrupt 36-39 Priority (PRI9), offset 0x424 ..................................................................... 144
Interrupt 40-43 Priority (PRI10), offset 0x428 ................................................................... 144
Interrupt 44-47 Priority (PRI11), offset 0x42C ................................................................... 144
Interrupt 48-51 Priority (PRI12), offset 0x430 ................................................................... 144
Interrupt 52-55 Priority (PRI13), offset 0x434 ................................................................... 144
Interrupt 56-59 Priority (PRI14), offset 0x438 ................................................................... 144
Interrupt 60-63 Priority (PRI15), offset 0x43C .................................................................. 144
Interrupt 64-67 Priority (PRI16), offset 0x440 ................................................................... 146
Interrupt 68-71 Priority (PRI17), offset 0x444 ................................................................... 146
Interrupt 72-75 Priority (PRI18), offset 0x448 ................................................................... 146
Interrupt 76-79 Priority (PRI19), offset 0x44C .................................................................. 146
Interrupt 80-83 Priority (PRI20), offset 0x450 ................................................................... 146
Interrupt 84-87 Priority (PRI21), offset 0x454 ................................................................... 146
Interrupt 88-91 Priority (PRI22), offset 0x458 ................................................................... 146
Interrupt 92-95 Priority (PRI23), offset 0x45C .................................................................. 146
Interrupt 96-99 Priority (PRI24), offset 0x460 ................................................................... 146
Interrupt 100-103 Priority (PRI25), offset 0x464 ............................................................... 146
Interrupt 104-107 Priority (PRI26), offset 0x468 ............................................................... 146
Interrupt 108-111 Priority (PRI27), offset 0x46C ............................................................... 146
Interrupt 112-115 Priority (PRI28), offset 0x470 ................................................................ 146
Interrupt 116-119 Priority (PRI29), offset 0x474 ................................................................ 146
Interrupt 120-123 Priority (PRI30), offset 0x478 ............................................................... 146
Interrupt 124-127 Priority (PRI31), offset 0x47C ............................................................... 146
Interrupt 128-131 Priority (PRI32), offset 0x480 ............................................................... 146
Interrupt 132-135 Priority (PRI33), offset 0x484 ............................................................... 146
Interrupt 136-138 Priority (PRI34), offset 0x488 ............................................................... 146
Software Trigger Interrupt (SWTRIG), offset 0xF00 .......................................................... 148
Auxiliary Control (ACTLR), offset 0x008 .......................................................................... 149
CPU ID Base (CPUID), offset 0xD00 ............................................................................... 151
Interrupt Control and State (INTCTRL), offset 0xD04 ........................................................ 152
Vector Table Offset (VTABLE), offset 0xD08 .................................................................... 155
Application Interrupt and Reset Control (APINT), offset 0xD0C ......................................... 156
July 17, 2013
19
Texas Instruments-Production Data
Table of Contents
Register 70:
Register 71:
Register 72:
Register 73:
Register 74:
Register 75:
Register 76:
Register 77:
Register 78:
Register 79:
Register 80:
Register 81:
Register 82:
Register 83:
Register 84:
Register 85:
Register 86:
Register 87:
Register 88:
Register 89:
Register 90:
Register 91:
Register 92:
Register 93:
Register 94:
System Control (SYSCTRL), offset 0xD10 ....................................................................... 158
Configuration and Control (CFGCTRL), offset 0xD14 ....................................................... 160
System Handler Priority 1 (SYSPRI1), offset 0xD18 ......................................................... 162
System Handler Priority 2 (SYSPRI2), offset 0xD1C ........................................................ 163
System Handler Priority 3 (SYSPRI3), offset 0xD20 ......................................................... 164
System Handler Control and State (SYSHNDCTRL), offset 0xD24 .................................... 165
Configurable Fault Status (FAULTSTAT), offset 0xD28 ..................................................... 169
Hard Fault Status (HFAULTSTAT), offset 0xD2C .............................................................. 175
Memory Management Fault Address (MMADDR), offset 0xD34 ........................................ 176
Bus Fault Address (FAULTADDR), offset 0xD38 .............................................................. 177
MPU Type (MPUTYPE), offset 0xD90 ............................................................................. 178
MPU Control (MPUCTRL), offset 0xD94 .......................................................................... 179
MPU Region Number (MPUNUMBER), offset 0xD98 ....................................................... 181
MPU Region Base Address (MPUBASE), offset 0xD9C ................................................... 182
MPU Region Base Address Alias 1 (MPUBASE1), offset 0xDA4 ....................................... 182
MPU Region Base Address Alias 2 (MPUBASE2), offset 0xDAC ...................................... 182
MPU Region Base Address Alias 3 (MPUBASE3), offset 0xDB4 ....................................... 182
MPU Region Attribute and Size (MPUATTR), offset 0xDA0 ............................................... 184
MPU Region Attribute and Size Alias 1 (MPUATTR1), offset 0xDA8 .................................. 184
MPU Region Attribute and Size Alias 2 (MPUATTR2), offset 0xDB0 .................................. 184
MPU Region Attribute and Size Alias 3 (MPUATTR3), offset 0xDB8 .................................. 184
Coprocessor Access Control (CPAC), offset 0xD88 .......................................................... 187
Floating-Point Context Control (FPCC), offset 0xF34 ........................................................ 188
Floating-Point Context Address (FPCA), offset 0xF38 ...................................................... 190
Floating-Point Default Status Control (FPDSC), offset 0xF3C ........................................... 191
System Control ............................................................................................................................ 204
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Device Identification 0 (DID0), offset 0x000 ..................................................................... 229
Device Identification 1 (DID1), offset 0x004 ..................................................................... 231
Brown-Out Reset Control (PBORCTL), offset 0x030 ........................................................ 234
Raw Interrupt Status (RIS), offset 0x050 .......................................................................... 235
Interrupt Mask Control (IMC), offset 0x054 ...................................................................... 237
Masked Interrupt Status and Clear (MISC), offset 0x058 .................................................. 239
Reset Cause (RESC), offset 0x05C ................................................................................ 242
Run-Mode Clock Configuration (RCC), offset 0x060 ......................................................... 244
GPIO High-Performance Bus Control (GPIOHBCTL), offset 0x06C ................................... 248
Run-Mode Clock Configuration 2 (RCC2), offset 0x070 .................................................... 251
Main Oscillator Control (MOSCCTL), offset 0x07C ........................................................... 254
Deep Sleep Clock Configuration (DSLPCLKCFG), offset 0x144 ........................................ 255
System Properties (SYSPROP), offset 0x14C .................................................................. 257
Precision Internal Oscillator Calibration (PIOSCCAL), offset 0x150 ................................... 259
Precision Internal Oscillator Statistics (PIOSCSTAT), offset 0x154 .................................... 261
PLL Frequency 0 (PLLFREQ0), offset 0x160 ................................................................... 262
PLL Frequency 1 (PLLFREQ1), offset 0x164 ................................................................... 263
PLL Status (PLLSTAT), offset 0x168 ............................................................................... 264
Sleep Power Configuration (SLPPWRCFG), offset 0x188 ................................................. 265
Deep-Sleep Power Configuration (DSLPPWRCFG), offset 0x18C ..................................... 267
LDO Sleep Power Control (LDOSPCTL), offset 0x1B4 ..................................................... 269
LDO Sleep Power Calibration (LDOSPCAL), offset 0x1B8 ................................................ 271
20
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
Register 31:
Register 32:
Register 33:
Register 34:
Register 35:
Register 36:
Register 37:
Register 38:
Register 39:
Register 40:
Register 41:
Register 42:
Register 43:
Register 44:
Register 45:
Register 46:
Register 47:
Register 48:
Register 49:
Register 50:
Register 51:
Register 52:
Register 53:
Register 54:
Register 55:
Register 56:
Register 57:
Register 58:
Register 59:
Register 60:
Register 61:
Register 62:
Register 63:
Register 64:
Register 65:
LDO Deep-Sleep Power Control (LDODPCTL), offset 0x1BC ........................................... 272
LDO Deep-Sleep Power Calibration (LDODPCAL), offset 0x1C0 ...................................... 274
Sleep / Deep-Sleep Power Mode Status (SDPMST), offset 0x1CC .................................... 275
Watchdog Timer Peripheral Present (PPWD), offset 0x300 ............................................... 278
16/32-Bit General-Purpose Timer Peripheral Present (PPTIMER), offset 0x304 ................. 279
General-Purpose Input/Output Peripheral Present (PPGPIO), offset 0x308 ........................ 281
Micro Direct Memory Access Peripheral Present (PPDMA), offset 0x30C .......................... 284
Hibernation Peripheral Present (PPHIB), offset 0x314 ...................................................... 285
Universal Asynchronous Receiver/Transmitter Peripheral Present (PPUART), offset
0x318 ........................................................................................................................... 286
Synchronous Serial Interface Peripheral Present (PPSSI), offset 0x31C ............................ 288
Inter-Integrated Circuit Peripheral Present (PPI2C), offset 0x320 ...................................... 290
Universal Serial Bus Peripheral Present (PPUSB), offset 0x328 ........................................ 292
Controller Area Network Peripheral Present (PPCAN), offset 0x334 .................................. 293
Analog-to-Digital Converter Peripheral Present (PPADC), offset 0x338 ............................. 294
Analog Comparator Peripheral Present (PPACMP), offset 0x33C ...................................... 295
Pulse Width Modulator Peripheral Present (PPPWM), offset 0x340 ................................... 296
Quadrature Encoder Interface Peripheral Present (PPQEI), offset 0x344 ........................... 297
EEPROM Peripheral Present (PPEEPROM), offset 0x358 ................................................ 298
32/64-Bit Wide General-Purpose Timer Peripheral Present (PPWTIMER), offset 0x35C ..... 299
Watchdog Timer Software Reset (SRWD), offset 0x500 ................................................... 301
16/32-Bit General-Purpose Timer Software Reset (SRTIMER), offset 0x504 ...................... 303
General-Purpose Input/Output Software Reset (SRGPIO), offset 0x508 ............................ 305
Micro Direct Memory Access Software Reset (SRDMA), offset 0x50C ............................... 308
Hibernation Software Reset (SRHIB), offset 0x514 ........................................................... 309
Universal Asynchronous Receiver/Transmitter Software Reset (SRUART), offset 0x518 .... 310
Synchronous Serial Interface Software Reset (SRSSI), offset 0x51C ................................ 312
Inter-Integrated Circuit Software Reset (SRI2C), offset 0x520 ........................................... 314
Controller Area Network Software Reset (SRCAN), offset 0x534 ....................................... 316
Analog-to-Digital Converter Software Reset (SRADC), offset 0x538 .................................. 318
Analog Comparator Software Reset (SRACMP), offset 0x53C .......................................... 320
Pulse Width Modulator Software Reset (SRPWM), offset 0x540 ....................................... 321
Quadrature Encoder Interface Software Reset (SRQEI), offset 0x544 ............................... 323
EEPROM Software Reset (SREEPROM), offset 0x558 .................................................... 325
32/64-Bit Wide General-Purpose Timer Software Reset (SRWTIMER), offset 0x55C .......... 326
Watchdog Timer Run Mode Clock Gating Control (RCGCWD), offset 0x600 ...................... 328
16/32-Bit General-Purpose Timer Run Mode Clock Gating Control (RCGCTIMER), offset
0x604 ........................................................................................................................... 329
General-Purpose Input/Output Run Mode Clock Gating Control (RCGCGPIO), offset
0x608 ........................................................................................................................... 331
Micro Direct Memory Access Run Mode Clock Gating Control (RCGCDMA), offset
0x60C ........................................................................................................................... 334
Hibernation Run Mode Clock Gating Control (RCGCHIB), offset 0x614 ............................. 335
Universal Asynchronous Receiver/Transmitter Run Mode Clock Gating Control (RCGCUART),
offset 0x618 .................................................................................................................. 336
Synchronous Serial Interface Run Mode Clock Gating Control (RCGCSSI), offset
0x61C ........................................................................................................................... 338
Inter-Integrated Circuit Run Mode Clock Gating Control (RCGCI2C), offset 0x620 ............. 340
Controller Area Network Run Mode Clock Gating Control (RCGCCAN), offset 0x634 ......... 342
July 17, 2013
21
Texas Instruments-Production Data
Table of Contents
Register 66:
Register 67:
Register 68:
Register 69:
Register 70:
Register 71:
Register 72:
Register 73:
Register 74:
Register 75:
Register 76:
Register 77:
Register 78:
Register 79:
Register 80:
Register 81:
Register 82:
Register 83:
Register 84:
Register 85:
Register 86:
Register 87:
Register 88:
Register 89:
Register 90:
Register 91:
Register 92:
Register 93:
Register 94:
Register 95:
Register 96:
Analog-to-Digital Converter Run Mode Clock Gating Control (RCGCADC), offset 0x638 .... 343
Analog Comparator Run Mode Clock Gating Control (RCGCACMP), offset 0x63C ............. 344
Pulse Width Modulator Run Mode Clock Gating Control (RCGCPWM), offset 0x640 .......... 345
Quadrature Encoder Interface Run Mode Clock Gating Control (RCGCQEI), offset
0x644 ........................................................................................................................... 346
EEPROM Run Mode Clock Gating Control (RCGCEEPROM), offset 0x658 ....................... 347
32/64-Bit Wide General-Purpose Timer Run Mode Clock Gating Control (RCGCWTIMER),
offset 0x65C .................................................................................................................. 348
Watchdog Timer Sleep Mode Clock Gating Control (SCGCWD), offset 0x700 .................... 350
16/32-Bit General-Purpose Timer Sleep Mode Clock Gating Control (SCGCTIMER), offset
0x704 ........................................................................................................................... 351
General-Purpose Input/Output Sleep Mode Clock Gating Control (SCGCGPIO), offset
0x708 ........................................................................................................................... 353
Micro Direct Memory Access Sleep Mode Clock Gating Control (SCGCDMA), offset
0x70C ........................................................................................................................... 356
Hibernation Sleep Mode Clock Gating Control (SCGCHIB), offset 0x714 ........................... 357
Universal Asynchronous Receiver/Transmitter Sleep Mode Clock Gating Control
(SCGCUART), offset 0x718 ............................................................................................ 358
Synchronous Serial Interface Sleep Mode Clock Gating Control (SCGCSSI), offset
0x71C ........................................................................................................................... 360
Inter-Integrated Circuit Sleep Mode Clock Gating Control (SCGCI2C), offset 0x720 ........... 362
Controller Area Network Sleep Mode Clock Gating Control (SCGCCAN), offset 0x734 ....... 364
Analog-to-Digital Converter Sleep Mode Clock Gating Control (SCGCADC), offset
0x738 ........................................................................................................................... 365
Analog Comparator Sleep Mode Clock Gating Control (SCGCACMP), offset 0x73C .......... 366
Pulse Width Modulator Sleep Mode Clock Gating Control (SCGCPWM), offset 0x740 ........ 367
Quadrature Encoder Interface Sleep Mode Clock Gating Control (SCGCQEI), offset
0x744 ........................................................................................................................... 368
EEPROM Sleep Mode Clock Gating Control (SCGCEEPROM), offset 0x758 ..................... 369
32/64-Bit Wide General-Purpose Timer Sleep Mode Clock Gating Control (SCGCWTIMER),
offset 0x75C .................................................................................................................. 370
Watchdog Timer Deep-Sleep Mode Clock Gating Control (DCGCWD), offset 0x800 .......... 372
16/32-Bit General-Purpose Timer Deep-Sleep Mode Clock Gating Control (DCGCTIMER),
offset 0x804 .................................................................................................................. 373
General-Purpose Input/Output Deep-Sleep Mode Clock Gating Control (DCGCGPIO), offset
0x808 ........................................................................................................................... 375
Micro Direct Memory Access Deep-Sleep Mode Clock Gating Control (DCGCDMA), offset
0x80C ........................................................................................................................... 378
Hibernation Deep-Sleep Mode Clock Gating Control (DCGCHIB), offset 0x814 .................. 379
Universal Asynchronous Receiver/Transmitter Deep-Sleep Mode Clock Gating Control
(DCGCUART), offset 0x818 ............................................................................................ 380
Synchronous Serial Interface Deep-Sleep Mode Clock Gating Control (DCGCSSI), offset
0x81C ........................................................................................................................... 382
Inter-Integrated Circuit Deep-Sleep Mode Clock Gating Control (DCGCI2C), offset
0x820 ........................................................................................................................... 384
Controller Area Network Deep-Sleep Mode Clock Gating Control (DCGCCAN), offset
0x834 ........................................................................................................................... 386
Analog-to-Digital Converter Deep-Sleep Mode Clock Gating Control (DCGCADC), offset
0x838 ........................................................................................................................... 387
22
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 97:
Register 98:
Register 99:
Register 100:
Register 101:
Register 102:
Register 103:
Register 104:
Register 105:
Register 106:
Register 107:
Register 108:
Register 109:
Register 110:
Register 111:
Register 112:
Register 113:
Register 114:
Register 115:
Register 116:
Register 117:
Register 118:
Register 119:
Register 120:
Register 121:
Register 122:
Register 123:
Register 124:
Register 125:
Register 126:
Register 127:
Register 128:
Register 129:
Register 130:
Register 131:
Register 132:
Register 133:
Register 134:
Register 135:
Register 136:
Register 137:
Register 138:
Register 139:
Analog Comparator Deep-Sleep Mode Clock Gating Control (DCGCACMP), offset
0x83C ........................................................................................................................... 388
Pulse Width Modulator Deep-Sleep Mode Clock Gating Control (DCGCPWM), offset
0x840 ........................................................................................................................... 389
Quadrature Encoder Interface Deep-Sleep Mode Clock Gating Control (DCGCQEI), offset
0x844 ........................................................................................................................... 390
EEPROM Deep-Sleep Mode Clock Gating Control (DCGCEEPROM), offset 0x858 ........... 391
32/64-Bit Wide General-Purpose Timer Deep-Sleep Mode Clock Gating Control
(DCGCWTIMER), offset 0x85C ...................................................................................... 392
Watchdog Timer Peripheral Ready (PRWD), offset 0xA00 ................................................ 394
16/32-Bit General-Purpose Timer Peripheral Ready (PRTIMER), offset 0xA04 ................... 395
General-Purpose Input/Output Peripheral Ready (PRGPIO), offset 0xA08 ......................... 397
Micro Direct Memory Access Peripheral Ready (PRDMA), offset 0xA0C ........................... 399
Hibernation Peripheral Ready (PRHIB), offset 0xA14 ....................................................... 400
Universal Asynchronous Receiver/Transmitter Peripheral Ready (PRUART), offset
0xA18 ........................................................................................................................... 401
Synchronous Serial Interface Peripheral Ready (PRSSI), offset 0xA1C ............................. 403
Inter-Integrated Circuit Peripheral Ready (PRI2C), offset 0xA20 ....................................... 405
Controller Area Network Peripheral Ready (PRCAN), offset 0xA34 ................................... 407
Analog-to-Digital Converter Peripheral Ready (PRADC), offset 0xA38 ............................... 408
Analog Comparator Peripheral Ready (PRACMP), offset 0xA3C ....................................... 409
Pulse Width Modulator Peripheral Ready (PRPWM), offset 0xA40 .................................... 410
Quadrature Encoder Interface Peripheral Ready (PRQEI), offset 0xA44 ............................ 411
EEPROM Peripheral Ready (PREEPROM), offset 0xA58 ................................................. 412
32/64-Bit Wide General-Purpose Timer Peripheral Ready (PRWTIMER), offset 0xA5C ...... 413
Device Capabilities 0 (DC0), offset 0x008 ........................................................................ 415
Device Capabilities 1 (DC1), offset 0x010 ........................................................................ 417
Device Capabilities 2 (DC2), offset 0x014 ........................................................................ 420
Device Capabilities 3 (DC3), offset 0x018 ........................................................................ 423
Device Capabilities 4 (DC4), offset 0x01C ....................................................................... 427
Device Capabilities 5 (DC5), offset 0x020 ........................................................................ 430
Device Capabilities 6 (DC6), offset 0x024 ........................................................................ 432
Device Capabilities 7 (DC7), offset 0x028 ........................................................................ 433
Device Capabilities 8 (DC8), offset 0x02C ....................................................................... 436
Software Reset Control 0 (SRCR0), offset 0x040 ............................................................. 439
Software Reset Control 1 (SRCR1), offset 0x044 ............................................................. 441
Software Reset Control 2 (SRCR2), offset 0x048 ............................................................. 444
Run Mode Clock Gating Control Register 0 (RCGC0), offset 0x100 ................................... 446
Run Mode Clock Gating Control Register 1 (RCGC1), offset 0x104 ................................... 450
Run Mode Clock Gating Control Register 2 (RCGC2), offset 0x108 ................................... 454
Sleep Mode Clock Gating Control Register 0 (SCGC0), offset 0x110 ................................. 457
Sleep Mode Clock Gating Control Register 1 (SCGC1), offset 0x114 ................................. 460
Sleep Mode Clock Gating Control Register 2 (SCGC2), offset 0x118 ................................. 464
Deep Sleep Mode Clock Gating Control Register 0 (DCGC0), offset 0x120 ....................... 466
Deep-Sleep Mode Clock Gating Control Register 1 (DCGC1), offset 0x124 ....................... 469
Deep Sleep Mode Clock Gating Control Register 2 (DCGC2), offset 0x128 ....................... 473
Device Capabilities 9 (DC9), offset 0x190 ........................................................................ 475
Non-Volatile Memory Information (NVMSTAT), offset 0x1A0 ............................................. 477
July 17, 2013
23
Texas Instruments-Production Data
Table of Contents
System Exception Module .......................................................................................................... 478
Register 1:
Register 2:
Register 3:
Register 4:
System Exception Raw Interrupt Status (SYSEXCRIS), offset 0x000 ................................
System Exception Interrupt Mask (SYSEXCIM), offset 0x004 ...........................................
System Exception Masked Interrupt Status (SYSEXCMIS), offset 0x008 ...........................
System Exception Interrupt Clear (SYSEXCIC), offset 0x00C ...........................................
479
481
483
485
Hibernation Module ..................................................................................................................... 486
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Hibernation RTC Counter (HIBRTCC), offset 0x000 .........................................................
Hibernation RTC Match 0 (HIBRTCM0), offset 0x004 .......................................................
Hibernation RTC Load (HIBRTCLD), offset 0x00C ...........................................................
Hibernation Control (HIBCTL), offset 0x010 .....................................................................
Hibernation Interrupt Mask (HIBIM), offset 0x014 .............................................................
Hibernation Raw Interrupt Status (HIBRIS), offset 0x018 ..................................................
Hibernation Masked Interrupt Status (HIBMIS), offset 0x01C ............................................
Hibernation Interrupt Clear (HIBIC), offset 0x020 .............................................................
Hibernation RTC Trim (HIBRTCT), offset 0x024 ...............................................................
Hibernation RTC Sub Seconds (HIBRTCSS), offset 0x028 ...............................................
Hibernation Data (HIBDATA), offset 0x030-0x06F ............................................................
500
501
502
503
507
509
511
513
514
515
516
Internal Memory ........................................................................................................................... 517
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
Flash Memory Address (FMA), offset 0x000 .................................................................... 534
Flash Memory Data (FMD), offset 0x004 ......................................................................... 535
Flash Memory Control (FMC), offset 0x008 ..................................................................... 536
Flash Controller Raw Interrupt Status (FCRIS), offset 0x00C ............................................ 538
Flash Controller Interrupt Mask (FCIM), offset 0x010 ........................................................ 541
Flash Controller Masked Interrupt Status and Clear (FCMISC), offset 0x014 ..................... 543
Flash Memory Control 2 (FMC2), offset 0x020 ................................................................. 546
Flash Write Buffer Valid (FWBVAL), offset 0x030 ............................................................. 547
Flash Write Buffer n (FWBn), offset 0x100 - 0x17C .......................................................... 548
Flash Size (FSIZE), offset 0xFC0 .................................................................................... 549
SRAM Size (SSIZE), offset 0xFC4 .................................................................................. 550
ROM Software Map (ROMSWMAP), offset 0xFCC ........................................................... 551
EEPROM Size Information (EESIZE), offset 0x000 .......................................................... 552
EEPROM Current Block (EEBLOCK), offset 0x004 .......................................................... 553
EEPROM Current Offset (EEOFFSET), offset 0x008 ........................................................ 554
EEPROM Read-Write (EERDWR), offset 0x010 .............................................................. 555
EEPROM Read-Write with Increment (EERDWRINC), offset 0x014 .................................. 556
EEPROM Done Status (EEDONE), offset 0x018 .............................................................. 557
EEPROM Support Control and Status (EESUPP), offset 0x01C ........................................ 559
EEPROM Unlock (EEUNLOCK), offset 0x020 .................................................................. 561
EEPROM Protection (EEPROT), offset 0x030 ................................................................. 562
EEPROM Password (EEPASS0), offset 0x034 ................................................................. 564
EEPROM Password (EEPASS1), offset 0x038 ................................................................. 564
EEPROM Password (EEPASS2), offset 0x03C ................................................................ 564
EEPROM Interrupt (EEINT), offset 0x040 ........................................................................ 565
EEPROM Block Hide (EEHIDE), offset 0x050 .................................................................. 566
EEPROM Debug Mass Erase (EEDBGME), offset 0x080 ................................................. 567
EEPROM Peripheral Properties (EEPROMPP), offset 0xFC0 ........................................... 568
ROM Control (RMCTL), offset 0x0F0 .............................................................................. 569
Flash Memory Protection Read Enable 0 (FMPRE0), offset 0x130 and 0x200 ................... 570
24
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 31:
Register 32:
Register 33:
Register 34:
Register 35:
Register 36:
Register 37:
Register 38:
Flash Memory Protection Read Enable 1 (FMPRE1), offset 0x204 .................................... 570
Flash Memory Protection Program Enable 0 (FMPPE0), offset 0x134 and 0x400 ............... 571
Flash Memory Protection Program Enable 1 (FMPPE1), offset 0x404 ............................... 571
Boot Configuration (BOOTCFG), offset 0x1D0 ................................................................. 572
User Register 0 (USER_REG0), offset 0x1E0 .................................................................. 575
User Register 1 (USER_REG1), offset 0x1E4 .................................................................. 575
User Register 2 (USER_REG2), offset 0x1E8 .................................................................. 575
User Register 3 (USER_REG3), offset 0x1EC ................................................................. 575
Micro Direct Memory Access (μDMA) ........................................................................................ 576
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
Register 31:
Register 32:
Register 33:
Register 34:
Register 35:
DMA Channel Source Address End Pointer (DMASRCENDP), offset 0x000 ...................... 600
DMA Channel Destination Address End Pointer (DMADSTENDP), offset 0x004 ................ 601
DMA Channel Control Word (DMACHCTL), offset 0x008 .................................................. 602
DMA Status (DMASTAT), offset 0x000 ............................................................................ 607
DMA Configuration (DMACFG), offset 0x004 ................................................................... 609
DMA Channel Control Base Pointer (DMACTLBASE), offset 0x008 .................................. 610
DMA Alternate Channel Control Base Pointer (DMAALTBASE), offset 0x00C .................... 611
DMA Channel Wait-on-Request Status (DMAWAITSTAT), offset 0x010 ............................. 612
DMA Channel Software Request (DMASWREQ), offset 0x014 ......................................... 613
DMA Channel Useburst Set (DMAUSEBURSTSET), offset 0x018 .................................... 614
DMA Channel Useburst Clear (DMAUSEBURSTCLR), offset 0x01C ................................. 615
DMA Channel Request Mask Set (DMAREQMASKSET), offset 0x020 .............................. 616
DMA Channel Request Mask Clear (DMAREQMASKCLR), offset 0x024 ........................... 617
DMA Channel Enable Set (DMAENASET), offset 0x028 ................................................... 618
DMA Channel Enable Clear (DMAENACLR), offset 0x02C ............................................... 619
DMA Channel Primary Alternate Set (DMAALTSET), offset 0x030 .................................... 620
DMA Channel Primary Alternate Clear (DMAALTCLR), offset 0x034 ................................. 621
DMA Channel Priority Set (DMAPRIOSET), offset 0x038 ................................................. 622
DMA Channel Priority Clear (DMAPRIOCLR), offset 0x03C .............................................. 623
DMA Bus Error Clear (DMAERRCLR), offset 0x04C ........................................................ 624
DMA Channel Assignment (DMACHASGN), offset 0x500 ................................................. 625
DMA Channel Interrupt Status (DMACHIS), offset 0x504 .................................................. 626
DMA Channel Map Select 0 (DMACHMAP0), offset 0x510 ............................................... 627
DMA Channel Map Select 1 (DMACHMAP1), offset 0x514 ............................................... 628
DMA Channel Map Select 2 (DMACHMAP2), offset 0x518 ............................................... 629
DMA Channel Map Select 3 (DMACHMAP3), offset 0x51C .............................................. 630
DMA Peripheral Identification 0 (DMAPeriphID0), offset 0xFE0 ......................................... 631
DMA Peripheral Identification 1 (DMAPeriphID1), offset 0xFE4 ......................................... 632
DMA Peripheral Identification 2 (DMAPeriphID2), offset 0xFE8 ......................................... 633
DMA Peripheral Identification 3 (DMAPeriphID3), offset 0xFEC ........................................ 634
DMA Peripheral Identification 4 (DMAPeriphID4), offset 0xFD0 ......................................... 635
DMA PrimeCell Identification 0 (DMAPCellID0), offset 0xFF0 ........................................... 636
DMA PrimeCell Identification 1 (DMAPCellID1), offset 0xFF4 ........................................... 637
DMA PrimeCell Identification 2 (DMAPCellID2), offset 0xFF8 ........................................... 638
DMA PrimeCell Identification 3 (DMAPCellID3), offset 0xFFC ........................................... 639
General-Purpose Input/Outputs (GPIOs) ................................................................................... 640
Register 1:
Register 2:
Register 3:
GPIO Data (GPIODATA), offset 0x000 ............................................................................ 654
GPIO Direction (GPIODIR), offset 0x400 ......................................................................... 656
GPIO Interrupt Sense (GPIOIS), offset 0x404 .................................................................. 657
July 17, 2013
25
Texas Instruments-Production Data
Table of Contents
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
Register 31:
Register 32:
Register 33:
Register 34:
Register 35:
Register 36:
GPIO Interrupt Both Edges (GPIOIBE), offset 0x408 ........................................................ 658
GPIO Interrupt Event (GPIOIEV), offset 0x40C ................................................................ 659
GPIO Interrupt Mask (GPIOIM), offset 0x410 ................................................................... 660
GPIO Raw Interrupt Status (GPIORIS), offset 0x414 ........................................................ 661
GPIO Masked Interrupt Status (GPIOMIS), offset 0x418 ................................................... 662
GPIO Interrupt Clear (GPIOICR), offset 0x41C ................................................................ 663
GPIO Alternate Function Select (GPIOAFSEL), offset 0x420 ............................................ 664
GPIO 2-mA Drive Select (GPIODR2R), offset 0x500 ........................................................ 666
GPIO 4-mA Drive Select (GPIODR4R), offset 0x504 ........................................................ 667
GPIO 8-mA Drive Select (GPIODR8R), offset 0x508 ........................................................ 668
GPIO Open Drain Select (GPIOODR), offset 0x50C ......................................................... 669
GPIO Pull-Up Select (GPIOPUR), offset 0x510 ................................................................ 670
GPIO Pull-Down Select (GPIOPDR), offset 0x514 ........................................................... 672
GPIO Slew Rate Control Select (GPIOSLR), offset 0x518 ................................................ 674
GPIO Digital Enable (GPIODEN), offset 0x51C ................................................................ 675
GPIO Lock (GPIOLOCK), offset 0x520 ............................................................................ 677
GPIO Commit (GPIOCR), offset 0x524 ............................................................................ 678
GPIO Analog Mode Select (GPIOAMSEL), offset 0x528 ................................................... 680
GPIO Port Control (GPIOPCTL), offset 0x52C ................................................................. 682
GPIO ADC Control (GPIOADCCTL), offset 0x530 ............................................................ 684
GPIO DMA Control (GPIODMACTL), offset 0x534 ........................................................... 685
GPIO Peripheral Identification 4 (GPIOPeriphID4), offset 0xFD0 ....................................... 686
GPIO Peripheral Identification 5 (GPIOPeriphID5), offset 0xFD4 ....................................... 687
GPIO Peripheral Identification 6 (GPIOPeriphID6), offset 0xFD8 ....................................... 688
GPIO Peripheral Identification 7 (GPIOPeriphID7), offset 0xFDC ...................................... 689
GPIO Peripheral Identification 0 (GPIOPeriphID0), offset 0xFE0 ....................................... 690
GPIO Peripheral Identification 1 (GPIOPeriphID1), offset 0xFE4 ....................................... 691
GPIO Peripheral Identification 2 (GPIOPeriphID2), offset 0xFE8 ....................................... 692
GPIO Peripheral Identification 3 (GPIOPeriphID3), offset 0xFEC ...................................... 693
GPIO PrimeCell Identification 0 (GPIOPCellID0), offset 0xFF0 .......................................... 694
GPIO PrimeCell Identification 1 (GPIOPCellID1), offset 0xFF4 .......................................... 695
GPIO PrimeCell Identification 2 (GPIOPCellID2), offset 0xFF8 .......................................... 696
GPIO PrimeCell Identification 3 (GPIOPCellID3), offset 0xFFC ......................................... 697
General-Purpose Timers ............................................................................................................. 698
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
GPTM Configuration (GPTMCFG), offset 0x000 .............................................................. 721
GPTM Timer A Mode (GPTMTAMR), offset 0x004 ........................................................... 723
GPTM Timer B Mode (GPTMTBMR), offset 0x008 ........................................................... 727
GPTM Control (GPTMCTL), offset 0x00C ........................................................................ 731
GPTM Synchronize (GPTMSYNC), offset 0x010 .............................................................. 735
GPTM Interrupt Mask (GPTMIMR), offset 0x018 .............................................................. 739
GPTM Raw Interrupt Status (GPTMRIS), offset 0x01C ..................................................... 742
GPTM Masked Interrupt Status (GPTMMIS), offset 0x020 ................................................ 745
GPTM Interrupt Clear (GPTMICR), offset 0x024 .............................................................. 748
GPTM Timer A Interval Load (GPTMTAILR), offset 0x028 ................................................ 750
GPTM Timer B Interval Load (GPTMTBILR), offset 0x02C ................................................ 751
GPTM Timer A Match (GPTMTAMATCHR), offset 0x030 .................................................. 752
GPTM Timer B Match (GPTMTBMATCHR), offset 0x034 ................................................. 753
GPTM Timer A Prescale (GPTMTAPR), offset 0x038 ....................................................... 754
26
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
GPTM Timer B Prescale (GPTMTBPR), offset 0x03C ...................................................... 755
GPTM TimerA Prescale Match (GPTMTAPMR), offset 0x040 ........................................... 756
GPTM TimerB Prescale Match (GPTMTBPMR), offset 0x044 ........................................... 757
GPTM Timer A (GPTMTAR), offset 0x048 ....................................................................... 758
GPTM Timer B (GPTMTBR), offset 0x04C ....................................................................... 759
GPTM Timer A Value (GPTMTAV), offset 0x050 ............................................................... 760
GPTM Timer B Value (GPTMTBV), offset 0x054 .............................................................. 761
GPTM RTC Predivide (GPTMRTCPD), offset 0x058 ........................................................ 762
GPTM Timer A Prescale Snapshot (GPTMTAPS), offset 0x05C ........................................ 763
GPTM Timer B Prescale Snapshot (GPTMTBPS), offset 0x060 ........................................ 764
GPTM Timer A Prescale Value (GPTMTAPV), offset 0x064 .............................................. 765
GPTM Timer B Prescale Value (GPTMTBPV), offset 0x068 .............................................. 766
GPTM Peripheral Properties (GPTMPP), offset 0xFC0 ..................................................... 767
Watchdog Timers ......................................................................................................................... 768
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Watchdog Load (WDTLOAD), offset 0x000 ...................................................................... 772
Watchdog Value (WDTVALUE), offset 0x004 ................................................................... 773
Watchdog Control (WDTCTL), offset 0x008 ..................................................................... 774
Watchdog Interrupt Clear (WDTICR), offset 0x00C .......................................................... 776
Watchdog Raw Interrupt Status (WDTRIS), offset 0x010 .................................................. 777
Watchdog Masked Interrupt Status (WDTMIS), offset 0x014 ............................................. 778
Watchdog Test (WDTTEST), offset 0x418 ....................................................................... 779
Watchdog Lock (WDTLOCK), offset 0xC00 ..................................................................... 780
Watchdog Peripheral Identification 4 (WDTPeriphID4), offset 0xFD0 ................................. 781
Watchdog Peripheral Identification 5 (WDTPeriphID5), offset 0xFD4 ................................. 782
Watchdog Peripheral Identification 6 (WDTPeriphID6), offset 0xFD8 ................................. 783
Watchdog Peripheral Identification 7 (WDTPeriphID7), offset 0xFDC ................................ 784
Watchdog Peripheral Identification 0 (WDTPeriphID0), offset 0xFE0 ................................. 785
Watchdog Peripheral Identification 1 (WDTPeriphID1), offset 0xFE4 ................................. 786
Watchdog Peripheral Identification 2 (WDTPeriphID2), offset 0xFE8 ................................. 787
Watchdog Peripheral Identification 3 (WDTPeriphID3), offset 0xFEC ................................. 788
Watchdog PrimeCell Identification 0 (WDTPCellID0), offset 0xFF0 .................................... 789
Watchdog PrimeCell Identification 1 (WDTPCellID1), offset 0xFF4 .................................... 790
Watchdog PrimeCell Identification 2 (WDTPCellID2), offset 0xFF8 .................................... 791
Watchdog PrimeCell Identification 3 (WDTPCellID3 ), offset 0xFFC .................................. 792
Analog-to-Digital Converter (ADC) ............................................................................................. 793
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
ADC Active Sample Sequencer (ADCACTSS), offset 0x000 ............................................. 815
ADC Raw Interrupt Status (ADCRIS), offset 0x004 ........................................................... 817
ADC Interrupt Mask (ADCIM), offset 0x008 ..................................................................... 819
ADC Interrupt Status and Clear (ADCISC), offset 0x00C .................................................. 822
ADC Overflow Status (ADCOSTAT), offset 0x010 ............................................................ 825
ADC Event Multiplexer Select (ADCEMUX), offset 0x014 ................................................. 827
ADC Underflow Status (ADCUSTAT), offset 0x018 ........................................................... 832
ADC Trigger Source Select (ADCTSSEL), offset 0x01C ................................................... 833
ADC Sample Sequencer Priority (ADCSSPRI), offset 0x020 ............................................. 835
ADC Sample Phase Control (ADCSPC), offset 0x024 ...................................................... 837
ADC Processor Sample Sequence Initiate (ADCPSSI), offset 0x028 ................................. 839
ADC Sample Averaging Control (ADCSAC), offset 0x030 ................................................. 841
ADC Digital Comparator Interrupt Status and Clear (ADCDCISC), offset 0x034 ................. 842
July 17, 2013
27
Texas Instruments-Production Data
Table of Contents
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
Register 31:
Register 32:
Register 33:
Register 34:
Register 35:
Register 36:
Register 37:
Register 38:
Register 39:
Register 40:
Register 41:
Register 42:
Register 43:
Register 44:
Register 45:
Register 46:
Register 47:
Register 48:
Register 49:
Register 50:
Register 51:
Register 52:
Register 53:
Register 54:
Register 55:
Register 56:
Register 57:
Register 58:
ADC Control (ADCCTL), offset 0x038 ............................................................................. 844
ADC Sample Sequence Input Multiplexer Select 0 (ADCSSMUX0), offset 0x040 ............... 845
ADC Sample Sequence Control 0 (ADCSSCTL0), offset 0x044 ........................................ 847
ADC Sample Sequence Result FIFO 0 (ADCSSFIFO0), offset 0x048 ................................ 854
ADC Sample Sequence Result FIFO 1 (ADCSSFIFO1), offset 0x068 ................................ 854
ADC Sample Sequence Result FIFO 2 (ADCSSFIFO2), offset 0x088 ................................ 854
ADC Sample Sequence Result FIFO 3 (ADCSSFIFO3), offset 0x0A8 ............................... 854
ADC Sample Sequence FIFO 0 Status (ADCSSFSTAT0), offset 0x04C ............................. 855
ADC Sample Sequence FIFO 1 Status (ADCSSFSTAT1), offset 0x06C ............................. 855
ADC Sample Sequence FIFO 2 Status (ADCSSFSTAT2), offset 0x08C ............................ 855
ADC Sample Sequence FIFO 3 Status (ADCSSFSTAT3), offset 0x0AC ............................ 855
ADC Sample Sequence 0 Operation (ADCSSOP0), offset 0x050 ...................................... 857
ADC Sample Sequence 0 Digital Comparator Select (ADCSSDC0), offset 0x054 .............. 859
ADC Sample Sequence Extended Input Multiplexer Select 0 (ADCSSEMUX0), offset
0x058 ........................................................................................................................... 861
ADC Sample Sequence Input Multiplexer Select 1 (ADCSSMUX1), offset 0x060 ............... 863
ADC Sample Sequence Input Multiplexer Select 2 (ADCSSMUX2), offset 0x080 ............... 863
ADC Sample Sequence Control 1 (ADCSSCTL1), offset 0x064 ........................................ 864
ADC Sample Sequence Control 2 (ADCSSCTL2), offset 0x084 ........................................ 864
ADC Sample Sequence 1 Operation (ADCSSOP1), offset 0x070 ...................................... 868
ADC Sample Sequence 2 Operation (ADCSSOP2), offset 0x090 ..................................... 868
ADC Sample Sequence 1 Digital Comparator Select (ADCSSDC1), offset 0x074 .............. 869
ADC Sample Sequence 2 Digital Comparator Select (ADCSSDC2), offset 0x094 .............. 869
ADC Sample Sequence Extended Input Multiplexer Select 1 (ADCSSEMUX1), offset
0x078 ........................................................................................................................... 871
ADC Sample Sequence Extended Input Multiplexer Select 2 (ADCSSEMUX2), offset 0x098
..................................................................................................................................... 871
ADC Sample Sequence Input Multiplexer Select 3 (ADCSSMUX3), offset 0x0A0 ............... 873
ADC Sample Sequence Control 3 (ADCSSCTL3), offset 0x0A4 ........................................ 874
ADC Sample Sequence 3 Operation (ADCSSOP3), offset 0x0B0 ..................................... 876
ADC Sample Sequence 3 Digital Comparator Select (ADCSSDC3), offset 0x0B4 .............. 877
ADC Sample Sequence Extended Input Multiplexer Select 3 (ADCSSEMUX3), offset
0x0B8 ........................................................................................................................... 878
ADC Digital Comparator Reset Initial Conditions (ADCDCRIC), offset 0xD00 ..................... 879
ADC Digital Comparator Control 0 (ADCDCCTL0), offset 0xE00 ....................................... 884
ADC Digital Comparator Control 1 (ADCDCCTL1), offset 0xE04 ....................................... 884
ADC Digital Comparator Control 2 (ADCDCCTL2), offset 0xE08 ....................................... 884
ADC Digital Comparator Control 3 (ADCDCCTL3), offset 0xE0C ...................................... 884
ADC Digital Comparator Control 4 (ADCDCCTL4), offset 0xE10 ....................................... 884
ADC Digital Comparator Control 5 (ADCDCCTL5), offset 0xE14 ....................................... 884
ADC Digital Comparator Control 6 (ADCDCCTL6), offset 0xE18 ....................................... 884
ADC Digital Comparator Control 7 (ADCDCCTL7), offset 0xE1C ...................................... 884
ADC Digital Comparator Range 0 (ADCDCCMP0), offset 0xE40 ....................................... 887
ADC Digital Comparator Range 1 (ADCDCCMP1), offset 0xE44 ....................................... 887
ADC Digital Comparator Range 2 (ADCDCCMP2), offset 0xE48 ....................................... 887
ADC Digital Comparator Range 3 (ADCDCCMP3), offset 0xE4C ...................................... 887
ADC Digital Comparator Range 4 (ADCDCCMP4), offset 0xE50 ....................................... 887
ADC Digital Comparator Range 5 (ADCDCCMP5), offset 0xE54 ....................................... 887
ADC Digital Comparator Range 6 (ADCDCCMP6), offset 0xE58 ....................................... 887
28
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 59:
Register 60:
Register 61:
Register 62:
ADC Digital Comparator Range 7 (ADCDCCMP7), offset 0xE5C ......................................
ADC Peripheral Properties (ADCPP), offset 0xFC0 ..........................................................
ADC Peripheral Configuration (ADCPC), offset 0xFC4 .....................................................
ADC Clock Configuration (ADCCC), offset 0xFC8 ............................................................
887
888
890
891
Universal Asynchronous Receivers/Transmitters (UARTs) ..................................................... 892
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
UART Data (UARTDR), offset 0x000 ............................................................................... 905
UART Receive Status/Error Clear (UARTRSR/UARTECR), offset 0x004 ........................... 907
UART Flag (UARTFR), offset 0x018 ................................................................................ 910
UART IrDA Low-Power Register (UARTILPR), offset 0x020 ............................................. 913
UART Integer Baud-Rate Divisor (UARTIBRD), offset 0x024 ............................................ 914
UART Fractional Baud-Rate Divisor (UARTFBRD), offset 0x028 ....................................... 915
UART Line Control (UARTLCRH), offset 0x02C ............................................................... 916
UART Control (UARTCTL), offset 0x030 ......................................................................... 918
UART Interrupt FIFO Level Select (UARTIFLS), offset 0x034 ........................................... 922
UART Interrupt Mask (UARTIM), offset 0x038 ................................................................. 924
UART Raw Interrupt Status (UARTRIS), offset 0x03C ...................................................... 927
UART Masked Interrupt Status (UARTMIS), offset 0x040 ................................................. 930
UART Interrupt Clear (UARTICR), offset 0x044 ............................................................... 933
UART DMA Control (UARTDMACTL), offset 0x048 .......................................................... 935
UART 9-Bit Self Address (UART9BITADDR), offset 0x0A4 ............................................... 936
UART 9-Bit Self Address Mask (UART9BITAMASK), offset 0x0A8 .................................... 937
UART Peripheral Properties (UARTPP), offset 0xFC0 ...................................................... 938
UART Clock Configuration (UARTCC), offset 0xFC8 ........................................................ 939
UART Peripheral Identification 4 (UARTPeriphID4), offset 0xFD0 ..................................... 940
UART Peripheral Identification 5 (UARTPeriphID5), offset 0xFD4 ..................................... 941
UART Peripheral Identification 6 (UARTPeriphID6), offset 0xFD8 ..................................... 942
UART Peripheral Identification 7 (UARTPeriphID7), offset 0xFDC ..................................... 943
UART Peripheral Identification 0 (UARTPeriphID0), offset 0xFE0 ...................................... 944
UART Peripheral Identification 1 (UARTPeriphID1), offset 0xFE4 ...................................... 945
UART Peripheral Identification 2 (UARTPeriphID2), offset 0xFE8 ...................................... 946
UART Peripheral Identification 3 (UARTPeriphID3), offset 0xFEC ..................................... 947
UART PrimeCell Identification 0 (UARTPCellID0), offset 0xFF0 ........................................ 948
UART PrimeCell Identification 1 (UARTPCellID1), offset 0xFF4 ........................................ 949
UART PrimeCell Identification 2 (UARTPCellID2), offset 0xFF8 ........................................ 950
UART PrimeCell Identification 3 (UARTPCellID3), offset 0xFFC ........................................ 951
Synchronous Serial Interface (SSI) ............................................................................................ 952
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
SSI Control 0 (SSICR0), offset 0x000 .............................................................................. 968
SSI Control 1 (SSICR1), offset 0x004 .............................................................................. 970
SSI Data (SSIDR), offset 0x008 ...................................................................................... 972
SSI Status (SSISR), offset 0x00C ................................................................................... 973
SSI Clock Prescale (SSICPSR), offset 0x010 .................................................................. 975
SSI Interrupt Mask (SSIIM), offset 0x014 ......................................................................... 976
SSI Raw Interrupt Status (SSIRIS), offset 0x018 .............................................................. 977
SSI Masked Interrupt Status (SSIMIS), offset 0x01C ........................................................ 979
SSI Interrupt Clear (SSIICR), offset 0x020 ....................................................................... 981
SSI DMA Control (SSIDMACTL), offset 0x024 ................................................................. 982
SSI Clock Configuration (SSICC), offset 0xFC8 ............................................................... 983
SSI Peripheral Identification 4 (SSIPeriphID4), offset 0xFD0 ............................................. 984
July 17, 2013
29
Texas Instruments-Production Data
Table of Contents
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
SSI Peripheral Identification 5 (SSIPeriphID5), offset 0xFD4 .............................................
SSI Peripheral Identification 6 (SSIPeriphID6), offset 0xFD8 .............................................
SSI Peripheral Identification 7 (SSIPeriphID7), offset 0xFDC ............................................
SSI Peripheral Identification 0 (SSIPeriphID0), offset 0xFE0 .............................................
SSI Peripheral Identification 1 (SSIPeriphID1), offset 0xFE4 .............................................
SSI Peripheral Identification 2 (SSIPeriphID2), offset 0xFE8 .............................................
SSI Peripheral Identification 3 (SSIPeriphID3), offset 0xFEC ............................................
SSI PrimeCell Identification 0 (SSIPCellID0), offset 0xFF0 ...............................................
SSI PrimeCell Identification 1 (SSIPCellID1), offset 0xFF4 ...............................................
SSI PrimeCell Identification 2 (SSIPCellID2), offset 0xFF8 ...............................................
SSI PrimeCell Identification 3 (SSIPCellID3), offset 0xFFC ...............................................
985
986
987
988
989
990
991
992
993
994
995
Inter-Integrated Circuit (I2C) Interface ........................................................................................ 996
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
I2C Master Slave Address (I2CMSA), offset 0x000 ......................................................... 1018
I2C Master Control/Status (I2CMCS), offset 0x004 ......................................................... 1019
I2C Master Data (I2CMDR), offset 0x008 ....................................................................... 1024
I2C Master Timer Period (I2CMTPR), offset 0x00C ......................................................... 1025
I2C Master Interrupt Mask (I2CMIMR), offset 0x010 ....................................................... 1026
I2C Master Raw Interrupt Status (I2CMRIS), offset 0x014 ............................................... 1027
I2C Master Masked Interrupt Status (I2CMMIS), offset 0x018 .......................................... 1028
I2C Master Interrupt Clear (I2CMICR), offset 0x01C ....................................................... 1029
I2C Master Configuration (I2CMCR), offset 0x020 .......................................................... 1030
I2C Master Clock Low Timeout Count (I2CMCLKOCNT), offset 0x024 ............................. 1032
I2C Master Bus Monitor (I2CMBMON), offset 0x02C ....................................................... 1033
I2C Master Configuration 2 (I2CMCR2), offset 0x038 ...................................................... 1034
I2C Slave Own Address (I2CSOAR), offset 0x800 .......................................................... 1035
I2C Slave Control/Status (I2CSCSR), offset 0x804 ......................................................... 1036
I2C Slave Data (I2CSDR), offset 0x808 ......................................................................... 1038
I2C Slave Interrupt Mask (I2CSIMR), offset 0x80C ......................................................... 1039
I2C Slave Raw Interrupt Status (I2CSRIS), offset 0x810 ................................................. 1040
I2C Slave Masked Interrupt Status (I2CSMIS), offset 0x814 ............................................ 1041
I2C Slave Interrupt Clear (I2CSICR), offset 0x818 .......................................................... 1042
I2C Slave Own Address 2 (I2CSOAR2), offset 0x81C ..................................................... 1043
I2C Slave ACK Control (I2CSACKCTL), offset 0x820 ...................................................... 1044
I2C Peripheral Properties (I2CPP), offset 0xFC0 ............................................................ 1045
I2C Peripheral Configuration (I2CPC), offset 0xFC4 ....................................................... 1046
Controller Area Network (CAN) Module ................................................................................... 1047
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
CAN Control (CANCTL), offset 0x000 ............................................................................ 1069
CAN Status (CANSTS), offset 0x004 ............................................................................. 1071
CAN Error Counter (CANERR), offset 0x008 ................................................................. 1074
CAN Bit Timing (CANBIT), offset 0x00C ........................................................................ 1075
CAN Interrupt (CANINT), offset 0x010 ........................................................................... 1076
CAN Test (CANTST), offset 0x014 ................................................................................ 1077
CAN Baud Rate Prescaler Extension (CANBRPE), offset 0x018 ..................................... 1079
CAN IF1 Command Request (CANIF1CRQ), offset 0x020 .............................................. 1080
CAN IF2 Command Request (CANIF2CRQ), offset 0x080 .............................................. 1080
CAN IF1 Command Mask (CANIF1CMSK), offset 0x024 ................................................ 1081
CAN IF2 Command Mask (CANIF2CMSK), offset 0x084 ................................................ 1081
30
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
Register 31:
Register 32:
Register 33:
Register 34:
Register 35:
Register 36:
Register 37:
CAN IF1 Mask 1 (CANIF1MSK1), offset 0x028 .............................................................. 1084
CAN IF2 Mask 1 (CANIF2MSK1), offset 0x088 .............................................................. 1084
CAN IF1 Mask 2 (CANIF1MSK2), offset 0x02C .............................................................. 1085
CAN IF2 Mask 2 (CANIF2MSK2), offset 0x08C .............................................................. 1085
CAN IF1 Arbitration 1 (CANIF1ARB1), offset 0x030 ....................................................... 1087
CAN IF2 Arbitration 1 (CANIF2ARB1), offset 0x090 ....................................................... 1087
CAN IF1 Arbitration 2 (CANIF1ARB2), offset 0x034 ....................................................... 1088
CAN IF2 Arbitration 2 (CANIF2ARB2), offset 0x094 ....................................................... 1088
CAN IF1 Message Control (CANIF1MCTL), offset 0x038 ................................................ 1090
CAN IF2 Message Control (CANIF2MCTL), offset 0x098 ................................................ 1090
CAN IF1 Data A1 (CANIF1DA1), offset 0x03C ............................................................... 1093
CAN IF1 Data A2 (CANIF1DA2), offset 0x040 ................................................................ 1093
CAN IF1 Data B1 (CANIF1DB1), offset 0x044 ................................................................ 1093
CAN IF1 Data B2 (CANIF1DB2), offset 0x048 ................................................................ 1093
CAN IF2 Data A1 (CANIF2DA1), offset 0x09C ............................................................... 1093
CAN IF2 Data A2 (CANIF2DA2), offset 0x0A0 ............................................................... 1093
CAN IF2 Data B1 (CANIF2DB1), offset 0x0A4 ............................................................... 1093
CAN IF2 Data B2 (CANIF2DB2), offset 0x0A8 ............................................................... 1093
CAN Transmission Request 1 (CANTXRQ1), offset 0x100 .............................................. 1094
CAN Transmission Request 2 (CANTXRQ2), offset 0x104 .............................................. 1094
CAN New Data 1 (CANNWDA1), offset 0x120 ............................................................... 1095
CAN New Data 2 (CANNWDA2), offset 0x124 ............................................................... 1095
CAN Message 1 Interrupt Pending (CANMSG1INT), offset 0x140 ................................... 1096
CAN Message 2 Interrupt Pending (CANMSG2INT), offset 0x144 ................................... 1096
CAN Message 1 Valid (CANMSG1VAL), offset 0x160 ..................................................... 1097
CAN Message 2 Valid (CANMSG2VAL), offset 0x164 ..................................................... 1097
Analog Comparators ................................................................................................................. 1098
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Analog Comparator Masked Interrupt Status (ACMIS), offset 0x000 ................................ 1105
Analog Comparator Raw Interrupt Status (ACRIS), offset 0x004 ..................................... 1106
Analog Comparator Interrupt Enable (ACINTEN), offset 0x008 ....................................... 1107
Analog Comparator Reference Voltage Control (ACREFCTL), offset 0x010 ..................... 1108
Analog Comparator Status 0 (ACSTAT0), offset 0x020 ................................................... 1109
Analog Comparator Status 1 (ACSTAT1), offset 0x040 ................................................... 1109
Analog Comparator Status 2 (ACSTAT2), offset 0x060 ................................................... 1109
Analog Comparator Control 0 (ACCTL0), offset 0x024 ................................................... 1110
Analog Comparator Control 1 (ACCTL1), offset 0x044 ................................................... 1110
Analog Comparator Control 2 (ACCTL2), offset 0x064 ................................................... 1110
Analog Comparator Peripheral Properties (ACMPPP), offset 0xFC0 ................................ 1112
Pulse Width Modulator (PWM) .................................................................................................. 1114
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
PWM Master Control (PWMCTL), offset 0x000 ..............................................................
PWM Time Base Sync (PWMSYNC), offset 0x004 .........................................................
PWM Output Enable (PWMENABLE), offset 0x008 ........................................................
PWM Output Inversion (PWMINVERT), offset 0x00C .....................................................
PWM Output Fault (PWMFAULT), offset 0x010 ..............................................................
PWM Interrupt Enable (PWMINTEN), offset 0x014 .........................................................
PWM Raw Interrupt Status (PWMRIS), offset 0x018 ......................................................
PWM Interrupt Status and Clear (PWMISC), offset 0x01C ..............................................
PWM Status (PWMSTATUS), offset 0x020 ....................................................................
July 17, 2013
1129
1131
1132
1134
1136
1138
1140
1143
1146
31
Texas Instruments-Production Data
Table of Contents
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
Register 31:
Register 32:
Register 33:
Register 34:
Register 35:
Register 36:
Register 37:
Register 38:
Register 39:
Register 40:
Register 41:
Register 42:
Register 43:
Register 44:
Register 45:
Register 46:
Register 47:
Register 48:
Register 49:
Register 50:
Register 51:
Register 52:
Register 53:
Register 54:
Register 55:
Register 56:
Register 57:
PWM Fault Condition Value (PWMFAULTVAL), offset 0x024 ........................................... 1148
PWM Enable Update (PWMENUPD), offset 0x028 ......................................................... 1150
PWM0 Control (PWM0CTL), offset 0x040 ...................................................................... 1154
PWM1 Control (PWM1CTL), offset 0x080 ...................................................................... 1154
PWM2 Control (PWM2CTL), offset 0x0C0 ..................................................................... 1154
PWM3 Control (PWM3CTL), offset 0x100 ...................................................................... 1154
PWM0 Interrupt and Trigger Enable (PWM0INTEN), offset 0x044 ................................... 1159
PWM1 Interrupt and Trigger Enable (PWM1INTEN), offset 0x084 ................................... 1159
PWM2 Interrupt and Trigger Enable (PWM2INTEN), offset 0x0C4 ................................... 1159
PWM3 Interrupt and Trigger Enable (PWM3INTEN), offset 0x104 ................................... 1159
PWM0 Raw Interrupt Status (PWM0RIS), offset 0x048 ................................................... 1162
PWM1 Raw Interrupt Status (PWM1RIS), offset 0x088 ................................................... 1162
PWM2 Raw Interrupt Status (PWM2RIS), offset 0x0C8 .................................................. 1162
PWM3 Raw Interrupt Status (PWM3RIS), offset 0x108 ................................................... 1162
PWM0 Interrupt Status and Clear (PWM0ISC), offset 0x04C .......................................... 1164
PWM1 Interrupt Status and Clear (PWM1ISC), offset 0x08C .......................................... 1164
PWM2 Interrupt Status and Clear (PWM2ISC), offset 0x0CC .......................................... 1164
PWM3 Interrupt Status and Clear (PWM3ISC), offset 0x10C .......................................... 1164
PWM0 Load (PWM0LOAD), offset 0x050 ...................................................................... 1166
PWM1 Load (PWM1LOAD), offset 0x090 ...................................................................... 1166
PWM2 Load (PWM2LOAD), offset 0x0D0 ...................................................................... 1166
PWM3 Load (PWM3LOAD), offset 0x110 ...................................................................... 1166
PWM0 Counter (PWM0COUNT), offset 0x054 ............................................................... 1167
PWM1 Counter (PWM1COUNT), offset 0x094 ............................................................... 1167
PWM2 Counter (PWM2COUNT), offset 0x0D4 .............................................................. 1167
PWM3 Counter (PWM3COUNT), offset 0x114 ............................................................... 1167
PWM0 Compare A (PWM0CMPA), offset 0x058 ............................................................ 1168
PWM1 Compare A (PWM1CMPA), offset 0x098 ............................................................ 1168
PWM2 Compare A (PWM2CMPA), offset 0x0D8 ............................................................ 1168
PWM3 Compare A (PWM3CMPA), offset 0x118 ............................................................. 1168
PWM0 Compare B (PWM0CMPB), offset 0x05C ............................................................ 1169
PWM1 Compare B (PWM1CMPB), offset 0x09C ............................................................ 1169
PWM2 Compare B (PWM2CMPB), offset 0x0DC ........................................................... 1169
PWM3 Compare B (PWM3CMPB), offset 0x11C ............................................................ 1169
PWM0 Generator A Control (PWM0GENA), offset 0x060 ............................................... 1170
PWM1 Generator A Control (PWM1GENA), offset 0x0A0 ............................................... 1170
PWM2 Generator A Control (PWM2GENA), offset 0x0E0 ............................................... 1170
PWM3 Generator A Control (PWM3GENA), offset 0x120 ............................................... 1170
PWM0 Generator B Control (PWM0GENB), offset 0x064 ............................................... 1173
PWM1 Generator B Control (PWM1GENB), offset 0x0A4 ............................................... 1173
PWM2 Generator B Control (PWM2GENB), offset 0x0E4 ............................................... 1173
PWM3 Generator B Control (PWM3GENB), offset 0x124 ............................................... 1173
PWM0 Dead-Band Control (PWM0DBCTL), offset 0x068 ............................................... 1176
PWM1 Dead-Band Control (PWM1DBCTL), offset 0x0A8 ............................................... 1176
PWM2 Dead-Band Control (PWM2DBCTL), offset 0x0E8 ............................................... 1176
PWM3 Dead-Band Control (PWM3DBCTL), offset 0x128 ............................................... 1176
PWM0 Dead-Band Rising-Edge Delay (PWM0DBRISE), offset 0x06C ............................ 1177
PWM1 Dead-Band Rising-Edge Delay (PWM1DBRISE), offset 0x0AC ............................ 1177
32
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 58:
Register 59:
Register 60:
Register 61:
Register 62:
Register 63:
Register 64:
Register 65:
Register 66:
Register 67:
Register 68:
Register 69:
Register 70:
Register 71:
Register 72:
Register 73:
Register 74:
Register 75:
Register 76:
Register 77:
Register 78:
Register 79:
Register 80:
Register 81:
Register 82:
Register 83:
Register 84:
Register 85:
Register 86:
Register 87:
Register 88:
PWM2 Dead-Band Rising-Edge Delay (PWM2DBRISE), offset 0x0EC ............................ 1177
PWM3 Dead-Band Rising-Edge Delay (PWM3DBRISE), offset 0x12C ............................ 1177
PWM0 Dead-Band Falling-Edge-Delay (PWM0DBFALL), offset 0x070 ............................ 1178
PWM1 Dead-Band Falling-Edge-Delay (PWM1DBFALL), offset 0x0B0 ............................ 1178
PWM2 Dead-Band Falling-Edge-Delay (PWM2DBFALL), offset 0x0F0 ............................ 1178
PWM3 Dead-Band Falling-Edge-Delay (PWM3DBFALL), offset 0x130 ............................ 1178
PWM0 Fault Source 0 (PWM0FLTSRC0), offset 0x074 .................................................. 1179
PWM1 Fault Source 0 (PWM1FLTSRC0), offset 0x0B4 .................................................. 1179
PWM2 Fault Source 0 (PWM2FLTSRC0), offset 0x0F4 .................................................. 1179
PWM3 Fault Source 0 (PWM3FLTSRC0), offset 0x134 .................................................. 1179
PWM0 Fault Source 1 (PWM0FLTSRC1), offset 0x078 .................................................. 1181
PWM1 Fault Source 1 (PWM1FLTSRC1), offset 0x0B8 .................................................. 1181
PWM2 Fault Source 1 (PWM2FLTSRC1), offset 0x0F8 .................................................. 1181
PWM3 Fault Source 1 (PWM3FLTSRC1), offset 0x138 .................................................. 1181
PWM0 Minimum Fault Period (PWM0MINFLTPER), offset 0x07C ................................... 1184
PWM1 Minimum Fault Period (PWM1MINFLTPER), offset 0x0BC ................................... 1184
PWM2 Minimum Fault Period (PWM2MINFLTPER), offset 0x0FC ................................... 1184
PWM3 Minimum Fault Period (PWM3MINFLTPER), offset 0x13C ................................... 1184
PWM0 Fault Pin Logic Sense (PWM0FLTSEN), offset 0x800 .......................................... 1185
PWM1 Fault Pin Logic Sense (PWM1FLTSEN), offset 0x880 .......................................... 1185
PWM2 Fault Pin Logic Sense (PWM2FLTSEN), offset 0x900 .......................................... 1185
PWM3 Fault Pin Logic Sense (PWM3FLTSEN), offset 0x980 .......................................... 1185
PWM0 Fault Status 0 (PWM0FLTSTAT0), offset 0x804 ................................................... 1186
PWM1 Fault Status 0 (PWM1FLTSTAT0), offset 0x884 ................................................... 1186
PWM2 Fault Status 0 (PWM2FLTSTAT0), offset 0x904 ................................................... 1186
PWM3 Fault Status 0 (PWM3FLTSTAT0), offset 0x984 ................................................... 1186
PWM0 Fault Status 1 (PWM0FLTSTAT1), offset 0x808 ................................................... 1188
PWM1 Fault Status 1 (PWM1FLTSTAT1), offset 0x888 ................................................... 1188
PWM2 Fault Status 1 (PWM2FLTSTAT1), offset 0x908 ................................................... 1188
PWM3 Fault Status 1 (PWM3FLTSTAT1), offset 0x988 ................................................... 1188
PWM Peripheral Properties (PWMPP), offset 0xFC0 ...................................................... 1191
Quadrature Encoder Interface (QEI) ........................................................................................ 1193
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
QEI Control (QEICTL), offset 0x000 ..............................................................................
QEI Status (QEISTAT), offset 0x004 ..............................................................................
QEI Position (QEIPOS), offset 0x008 ............................................................................
QEI Maximum Position (QEIMAXPOS), offset 0x00C .....................................................
QEI Timer Load (QEILOAD), offset 0x010 .....................................................................
QEI Timer (QEITIME), offset 0x014 ...............................................................................
QEI Velocity Counter (QEICOUNT), offset 0x018 ...........................................................
QEI Velocity (QEISPEED), offset 0x01C ........................................................................
QEI Interrupt Enable (QEIINTEN), offset 0x020 .............................................................
QEI Raw Interrupt Status (QEIRIS), offset 0x024 ...........................................................
QEI Interrupt Status and Clear (QEIISC), offset 0x028 ...................................................
July 17, 2013
1200
1203
1204
1205
1206
1207
1208
1209
1210
1212
1214
33
Texas Instruments-Production Data
Revision History
Revision History
The revision history table notes changes made between the indicated revisions of the
TM4C123BE6PZ data sheet.
Table 1. Revision History
Date
July 16, 2013
Revision
Description
15033.2672 ■
■
July 2013
14995.2667 ■
In the Electrical Characteristics chapter:
–
Added maximum junction temperature to Maximum Ratings table. Also moved Unpowered
storage temperature range parameter to this table.
–
In SSI Characteristics table, corrected values for TRXDMS, TRXDMH, and TRXDSSU. Also clarified
footnotes to table.
–
Corrected parameter numbers in figures "Master Mode SSI Timing for SPI Frame Format
(FRF=00), with SPH=1" and "Slave Mode SSI Timing for SPI Frame Format (FRF=00), with
SPH=1".
Additional minor data sheet clarifications and corrections.
Deleted erroneous references to the PWM Peripheral Configuration (PWMPC) register.
■
In the System Control chapter, corrected resets for bits [7:4] in System Properties (SYSPROP)
register.
■
In the Hibernation Module chapter:
–
Corrected figures "Using a Crystal as the Hibernation Clock Source with a Single Battery Source"
and "Using a Dedicated Oscillator as the Hibernation Clock Source with VDD3ON Mode".
–
Clarified when the Hibernation module can generate interrupts.
■
In the Internal Memory chapter, removed the INVPL bit from the EEPROM Done Status (EEDONE)
register.
■
In the uDMA chapter, in the µDMA Channel Assignments table, corrected names of timers 6-11 to
wide timers 0-5.
■
In the Timers chapter:
–
Clarified that the timer must be configured for one-shot or periodic time-out mode to produce
an ADC trigger assertion and that the GPTM does not generate triggers for match, compare
events or compare match events.
–
Added a step in the RTC Mode initialization and configuration: If the timer has been operating
in a different mode prior to this, clear any residual set bits in the GPTM Timer n Mode
(GPTMTnMR) register before reconfiguring.
■
In the Watchdog Timer chapter, added a note that locking the watchdog registers using the
WDTLOCK register does not affect the WDTICR register and allows interrupts to always be serviced.
■
In the SSI chapter, clarified note in Bit Rate Generation section to indicate that the System Clock
or the PIOSC can be used as the source for SSIClk. Also corrected to indicate maximum SSIClk
limit in SSI slave mode as well as the fact that SYSCLK has to be at least 12 times that of SSICLk.
■
In the PWM chapter, clarified that the PWM has two clock sources, selected by the USPWMDIV bit
in the Run-Mode Clock Configuration (RCC) register.
■
In the QEI chapter, noted that the INTERROR bit is only applicable when the QEI is operating in
quadrature phase mode (SIGMODE=0) and should be masked when SIGMODE=1. Similarly, the
34
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Table 1. Revision History (continued)
Date
Revision
Description
INTDIR bit is only applicable when the QEI is operating in clock/direction mode (SIGMODE=1) and
should be masked when SIGMODE=0.
■
In the Electrical Characteristics chapter:
–
Moved Maximum Ratings and ESD Absolute Maximum Ratings to the front of the chapter.
–
Added VBATRMP parameter to Maximum Ratings and Hibernation Module Battery Characteristics
tables.
–
Added ambient and junction temperatures to Temperature Characteristics table and clarified
values in Thermal Characteristics table.
–
Added clarifying footnote to VVDD_POK parameter in Power-On and Brown-Out Levels table.
–
Corrected GPIO Package Side Assignments table.
–
In the Flash Memory and EEPROM Characteristics tables, added a parameter for page/mass
erase times for 10k cycles and corrected existing values for all page and mass erase parameters.
–
Corrected DNL max value in ADC Electrical Characteristics table.
–
In the SSI Characteristics table, changed parameter names for S7-S14, provided a max number
instead of a min for S7, and corrected values for S9-S14.
–
Replaced figure "SSI Timing for SPI Frame Format (FRF=00), with SPH=1" with two figures,
one for Master Mode and one for Slave Mode.
–
Updated and added values to the table Table 23-39 on page 1293.
■
In the Package Information appendix, moved orderable devices table from addendum to appendix,
clarified part markings and moved packaging diagram from addendum to appendix.
■
Additional minor data sheet clarifications and corrections.
July 17, 2013
35
Texas Instruments-Production Data
About This Document
About This Document
This data sheet provides reference information for the TM4C123BE6PZ microcontroller, describing
the functional blocks of the system-on-chip (SoC) device designed around the ARM® Cortex™-M4F
core.
Audience
This manual is intended for system software developers, hardware designers, and application
developers.
About This Manual
This document is organized into sections that correspond to each major feature.
Related Documents
The following related documents are available on the Tiva™ C Series web site at
http://www.ti.com/tiva-c:
■ TM4C123BE6PZ Errata
■ ARM® Cortex™-M4 Errata
■ TivaWare™ Boot Loader for C Series User's Guide (literature number SPMU301)
■ TivaWare™ Graphics Library for C Series User's Guide (literature number SPMU300)
■ TivaWare™ Peripheral Driver Library for C Series User's Guide (literature number SPMU298)
■ TivaWare™ USB Library for C Series User's Guide (literature number SPMU297)
■ TM4C123BE6PZ ROM User’s Guide
The following related documents may also be useful:
■ Cortex™-M4 instruction set chapter in the ARM® Cortex™-M4 Devices Generic User Guide
(literature number ARM DUI 0553A)
■ ARM® Debug Interface V5 Architecture Specification
■ ARM® Embedded Trace Macrocell Architecture Specification
■ IEEE Standard 1149.1-Test Access Port and Boundary-Scan Architecture
This documentation list was current as of publication date. Please check the web site for additional
documentation, including application notes and white papers.
36
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Documentation Conventions
This document uses the conventions shown in Table 2 on page 37.
Table 2. Documentation Conventions
Notation
Meaning
General Register Notation
REGISTER
APB registers are indicated in uppercase bold. For example, PBORCTL is the Power-On and
Brown-Out Reset Control register. If a register name contains a lowercase n, it represents more
than one register. For example, SRCRn represents any (or all) of the three Software Reset Control
registers: SRCR0, SRCR1 , and SRCR2.
bit
A single bit in a register.
bit field
Two or more consecutive and related bits.
offset 0xnnn
A hexadecimal increment to a register's address, relative to that module's base address as specified
in Table 2-4 on page 84.
Register N
Registers are numbered consecutively throughout the document to aid in referencing them. The
register number has no meaning to software.
reserved
Register bits marked reserved are reserved for future use. In most cases, reserved bits are set to
0; however, user software should not rely on the value of a reserved bit. To provide software
compatibility with future products, the value of a reserved bit should be preserved across a
read-modify-write operation.
yy:xx
The range of register bits inclusive from xx to yy. For example, 31:15 means bits 15 through 31 in
that register.
Register Bit/Field
Types
This value in the register bit diagram indicates whether software running on the controller can
change the value of the bit field.
RC
Software can read this field. The bit or field is cleared by hardware after reading the bit/field.
RO
Software can read this field. Always write the chip reset value.
R/W
Software can read or write this field.
R/WC
Software can read or write this field. Writing to it with any value clears the register.
R/W1C
Software can read or write this field. A write of a 0 to a W1C bit does not affect the bit value in the
register. A write of a 1 clears the value of the bit in the register; the remaining bits remain unchanged.
This register type is primarily used for clearing interrupt status bits where the read operation
provides the interrupt status and the write of the read value clears only the interrupts being reported
at the time the register was read.
R/W1S
Software can read or write a 1 to this field. A write of a 0 to a R/W1S bit does not affect the bit
value in the register.
W1C
Software can write this field. A write of a 0 to a W1C bit does not affect the bit value in the register.
A write of a 1 clears the value of the bit in the register; the remaining bits remain unchanged. A
read of the register returns no meaningful data.
This register is typically used to clear the corresponding bit in an interrupt register.
WO
Only a write by software is valid; a read of the register returns no meaningful data.
Register Bit/Field
Reset Value
This value in the register bit diagram shows the bit/field value after any reset, unless noted.
0
Bit cleared to 0 on chip reset.
1
Bit set to 1 on chip reset.
-
Nondeterministic.
Pin/Signal Notation
[]
Pin alternate function; a pin defaults to the signal without the brackets.
pin
Refers to the physical connection on the package.
signal
Refers to the electrical signal encoding of a pin.
July 17, 2013
37
Texas Instruments-Production Data
About This Document
Table 2. Documentation Conventions (continued)
Notation
Meaning
assert a signal
Change the value of the signal from the logically False state to the logically True state. For active
High signals, the asserted signal value is 1 (High); for active Low signals, the asserted signal value
is 0 (Low). The active polarity (High or Low) is defined by the signal name (see SIGNAL and SIGNAL
below).
deassert a signal
Change the value of the signal from the logically True state to the logically False state.
SIGNAL
Signal names are in uppercase and in the Courier font. An overbar on a signal name indicates that
it is active Low. To assert SIGNAL is to drive it Low; to deassert SIGNAL is to drive it High.
SIGNAL
Signal names are in uppercase and in the Courier font. An active High signal has no overbar. To
assert SIGNAL is to drive it High; to deassert SIGNAL is to drive it Low.
Numbers
X
An uppercase X indicates any of several values is allowed, where X can be any legal pattern. For
example, a binary value of 0X00 can be either 0100 or 0000, a hex value of 0xX is 0x0 or 0x1, and
so on.
0x
Hexadecimal numbers have a prefix of 0x. For example, 0x00FF is the hexadecimal number FF.
All other numbers within register tables are assumed to be binary. Within conceptual information,
binary numbers are indicated with a b suffix, for example, 1011b, and decimal numbers are written
without a prefix or suffix.
38
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
1
Architectural Overview
®
Texas Instrument's Tiva™ C Series microcontrollers provide designers a high-performance ARM
Cortex™-M-based architecture with a broad set of integration capabilities and a strong ecosystem
of software and development tools. Targeting performance and flexibility, the Tiva™ C Series
architecture offers a 80 MHz Cortex-M with FPU, a variety of integrated memories and multiple
programmable GPIO. Tiva™ C Series devices offer consumers compelling cost-effective solutions
by integrating application-specific peripherals and providing a comprehensive library of software
tools which minimize board costs and design-cycle time. Offering quicker time-to-market and cost
savings, the Tiva™ C Series microcontrollers are the leading choice in high-performance 32-bit
applications.
This chapter contains an overview of the Tiva™ C Series microcontrollers as well as details on the
TM4C123BE6PZ microcontroller:
■ “Tiva™ C Series Overview” on page 39
■ “TM4C123BE6PZ Microcontroller Overview” on page 40
■ “TM4C123BE6PZ Microcontroller Features” on page 42
■ “TM4C123BE6PZ Microcontroller Hardware Details” on page 60
1.1
Tiva™ C Series Overview
The Tiva™ C Series ARM Cortex-M4 microcontrollers provide top performance and advanced
integration. The product family is positioned for cost-conscious applications requiring significant
control processing and connectivity capabilities such as:
■
■
■
■
■
■
■
■
■
■
■
Low power, hand-held smart devices
Gaming equipment
Home and commercial site monitoring and control
Motion control
Medical instrumentation
Test and measurement equipment
Factory automation
Fire and security
Smart Energy/Smart Grid solutions
Intelligent lighting control
Transportation
For applications requiring extreme conservation of power, the TM4C123BE6PZ microcontroller
features a battery-backed Hibernation module to efficiently power down the TM4C123BE6PZ to a
low-power state during extended periods of inactivity. With a power-up/power-down sequencer, a
continuous time counter (RTC), multiple wake-from-hibernate options, a high-speed interface to the
system bus, and dedicated battery-backed memory, the Hibernation module positions the
TM4C123BE6PZ microcontroller perfectly for battery applications.
In addition, the TM4C123BE6PZ microcontroller offers the advantages of ARM's widely available
development tools, System-on-Chip (SoC) infrastructure IP applications, and a large user community.
Additionally, the microcontroller uses ARM's Thumb®-compatible Thumb-2 instruction set to reduce
memory requirements and, thereby, cost. Finally, the TM4C123BE6PZ microcontroller is
code-compatible to all members of the extensive Tiva™ C Series; providing flexibility to fit precise
needs.
July 17, 2013
39
Texas Instruments-Production Data
Architectural Overview
Texas Instruments offers a complete solution to get to market quickly, with evaluation and
development boards, white papers and application notes, an easy-to-use peripheral driver library,
and a strong support, sales, and distributor network.
1.2
TM4C123BE6PZ Microcontroller Overview
The TM4C123BE6PZ microcontroller combines complex integration and high performance with the
features shown in Table 1-1.
Table 1-1. TM4C123BE6PZ Microcontroller Features
Feature
Description
Core
ARM Cortex-M4F processor core
Performance
80-MHz operation; 100 DMIPS performance
Flash
128 KB single-cycle Flash memory
System SRAM
32 KB single-cycle SRAM
EEPROM
2KB of EEPROM
Internal ROM
Internal ROM loaded with TivaWare™ for C Series software
Communication Interfaces
Universal Asynchronous Receivers/Transmitter (UART) Eight UARTs
Synchronous Serial Interface (SSI)
Inter-Integrated Circuit
(I2C)
Four SSI modules
Six I2C modules with four transmission speeds including high-speed
mode
Controller Area Network (CAN)
Two CAN 2.0 A/B controllers
System Integration
Micro Direct Memory Access (µDMA)
ARM® PrimeCell® 32-channel configurable μDMA controller
General-Purpose Timer (GPTM)
Six 16/32-bit GPTM blocks and six 32/64-bit Wide GPTM blocks
Watchdog Timer (WDT)
Two watchdog timers
Hibernation Module (HIB)
Low-power battery-backed Hibernation module
General-Purpose Input/Output (GPIO)
10 physical GPIO blocks
Advanced Motion Control
Pulse Width Modulator (PWM)
Two PWM modules, each with four PWM generator blocks and a
control block, for a total of 16 PWM outputs.
Quadrature Encoder Interface (QEI)
Two QEI modules
Analog Support
Analog-to-Digital Converter (ADC)
Two 12-bit ADC modules with a maximum sample rate of one million
samples/second
Analog Comparator Controller
Three independent integrated analog comparators
Digital Comparator
16 digital comparators
JTAG and Serial Wire Debug (SWD)
One JTAG module with integrated ARM SWD
Package
100-pin LQFP
Operating Range (Ambient)
Industrial (-40°C to 85°C) temperature range
Figure 1-1 on page 41 shows the features on the TM4C123BE6PZ microcontroller. Note that there
are two on-chip buses that connect the core to the peripherals. The Advanced Peripheral Bus (APB)
bus is the legacy bus. The Advanced High-Performance Bus (AHB) bus provides better back-to-back
access performance than the APB bus.
40
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Figure 1-1. Tiva™ TM4C123BE6PZ Microcontroller High-Level Block Diagram
JTAG/SWD
ARM®
Cortex™-M4F
ROM
(80MHz)
System
Control and
Clocks
(w/ Precis. Osc.)
ETM
FPU
NVIC
MPU
DCode bus
Boot Loader
DriverLib
AES & CRC
Flash
(128KB)
ICode bus
System Bus
TM4C123BE6PZ
Bus Matrix
SRAM
(32KB)
SYSTEM PERIPHERALS
EEPROM
(2K)
Hibernation
Module
GPIOs
(69)
GeneralPurpose
Timer (12)
I2C
(6)
CAN
Controller
(2)
Analog
Comparator
(3)
Advanced Peripheral Bus (APB)
Watchdog
Timer
(2)
Advanced High-Performance Bus (AHB)
DMA
SERIAL PERIPHERALS
UART
(8)
SSI
(4)
ANALOG PERIPHERALS
12- Bit ADC
Channels
(22)
MOTION CONTROL PERIPHERALS
PWM
(16)
QEI
(2)
July 17, 2013
41
Texas Instruments-Production Data
Architectural Overview
1.3
TM4C123BE6PZ Microcontroller Features
The TM4C123BE6PZ microcontroller component features and general function are discussed in
more detail in the following section.
1.3.1
ARM Cortex-M4F Processor Core
All members of the Tiva™ C Series, including the TM4C123BE6PZ microcontroller, are designed
around an ARM Cortex-M processor core. The ARM Cortex-M processor provides the core for a
high-performance, low-cost platform that meets the needs of minimal memory implementation,
reduced pin count, and low power consumption, while delivering outstanding computational
performance and exceptional system response to interrupts.
1.3.1.1
Processor Core (see page 61)
■ 32-bit ARM Cortex-M4F architecture optimized for small-footprint embedded applications
■ 80-MHz operation; 100 DMIPS performance
■ Outstanding processing performance combined with fast interrupt handling
■ Thumb-2 mixed 16-/32-bit instruction set delivers the high performance expected of a 32-bit
ARM core in a compact memory size usually associated with 8- and 16-bit devices, typically in
the range of a few kilobytes of memory for microcontroller-class applications
– Single-cycle multiply instruction and hardware divide
– Atomic bit manipulation (bit-banding), delivering maximum memory utilization and streamlined
peripheral control
– Unaligned data access, enabling data to be efficiently packed into memory
■ IEEE754-compliant single-precision Floating-Point Unit (FPU)
■ 16-bit SIMD vector processing unit
■ Fast code execution permits slower processor clock or increases sleep mode time
■ Harvard architecture characterized by separate buses for instruction and data
■ Efficient processor core, system and memories
■ Hardware division and fast digital-signal-processing orientated multiply accumulate
■ Saturating arithmetic for signal processing
■ Deterministic, high-performance interrupt handling for time-critical applications
■ Memory protection unit (MPU) to provide a privileged mode for protected operating system
functionality
■ Enhanced system debug with extensive breakpoint and trace capabilities
■ Serial Wire Debug and Serial Wire Trace reduce the number of pins required for debugging and
tracing
42
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
■ Migration from the ARM7™ processor family for better performance and power efficiency
■ Optimized for single-cycle Flash memory usage up to specific frequencies; see “Internal
Memory” on page 517 for more information.
■ Ultra-low power consumption with integrated sleep modes
1.3.1.2
System Timer (SysTick) (see page 115)
ARM Cortex-M4F includes an integrated system timer, SysTick. SysTick provides a simple, 24-bit,
clear-on-write, decrementing, wrap-on-zero counter with a flexible control mechanism. The counter
can be used in several different ways, for example:
■ An RTOS tick timer that fires at a programmable rate (for example, 100 Hz) and invokes a SysTick
routine
■ A high-speed alarm timer using the system clock
■ A variable rate alarm or signal timer—the duration is range-dependent on the reference clock
used and the dynamic range of the counter
■ A simple counter used to measure time to completion and time used
■ An internal clock-source control based on missing/meeting durations
1.3.1.3
Nested Vectored Interrupt Controller (NVIC) (see page 116)
The TM4C123BE6PZ controller includes the ARM Nested Vectored Interrupt Controller (NVIC). The
NVIC and Cortex-M4F prioritize and handle all exceptions in Handler Mode. The processor state is
automatically stored to the stack on an exception and automatically restored from the stack at the
end of the Interrupt Service Routine (ISR). The interrupt vector is fetched in parallel to the state
saving, enabling efficient interrupt entry. The processor supports tail-chaining, meaning that
back-to-back interrupts can be performed without the overhead of state saving and restoration.
Software can set eight priority levels on 7 exceptions (system handlers) and 84 interrupts.
■ Deterministic, fast interrupt processing: always 12 cycles, or just 6 cycles with tail-chaining (these
values reflect no FPU stacking)
■ External non-maskable interrupt signal (NMI) available for immediate execution of NMI handler
for safety critical applications
■ Dynamically reprioritizable interrupts
■ Exceptional interrupt handling via hardware implementation of required register manipulations
1.3.1.4
System Control Block (SCB) (see page 117)
The SCB provides system implementation information and system control, including configuration,
control, and reporting of system exceptions.
1.3.1.5
Memory Protection Unit (MPU) (see page 117)
The MPU supports the standard ARM7 Protected Memory System Architecture (PMSA) model. The
MPU provides full support for protection regions, overlapping protection regions, access permissions,
and exporting memory attributes to the system.
July 17, 2013
43
Texas Instruments-Production Data
Architectural Overview
1.3.1.6
Floating-Point Unit (FPU) (see page 122)
The FPU fully supports single-precision add, subtract, multiply, divide, multiply and accumulate,
and square root operations. It also provides conversions between fixed-point and floating-point data
formats, and floating-point constant instructions.
■ 32-bit instructions for single-precision (C float) data-processing operations
■ Combined multiply and accumulate instructions for increased precision (Fused MAC)
■ Hardware support for conversion, addition, subtraction, multiplication with optional accumulate,
division, and square-root
■ Hardware support for denormals and all IEEE rounding modes
■ 32 dedicated 32-bit single-precision registers, also addressable as 16 double-word registers
■ Decoupled three stage pipeline
1.3.2
On-Chip Memory
The TM4C123BE6PZ microcontroller is integrated with the following set of on-chip memory and
features:
■ 32 KB single-cycle SRAM
■ 128 KB Flash memory
■ 2KB EEPROM
■ Internal ROM loaded with TivaWare™ for C Series software:
– TivaWare™ Peripheral Driver Library
– TivaWare Boot Loader
– Advanced Encryption Standard (AES) cryptography tables
– Cyclic Redundancy Check (CRC) error detection functionality
1.3.2.1
SRAM (see page 518)
The TM4C123BE6PZ microcontroller provides 32 KB of single-cycle on-chip SRAM. The internal
SRAM of the device is located at offset 0x2000.0000 of the device memory map.
Because read-modify-write (RMW) operations are very time consuming, ARM has introduced
bit-banding technology in the Cortex-M4F processor. With a bit-band-enabled processor, certain
regions in the memory map (SRAM and peripheral space) can use address aliases to access
individual bits in a single, atomic operation.
Data can be transferred to and from the SRAM using the Micro Direct Memory Access Controller
(µDMA).
1.3.2.2
Flash Memory (see page 521)
The TM4C123BE6PZ microcontroller provides 128 KB of single-cycle on-chip Flash memory. The
Flash memory is organized as a set of 1-KB blocks that can be individually erased. Erasing a block
causes the entire contents of the block to be reset to all 1s. These blocks are paired into a set of
2-KB blocks that can be individually protected. The blocks can be marked as read-only or
execute-only, providing different levels of code protection. Read-only blocks cannot be erased or
programmed, protecting the contents of those blocks from being modified. Execute-only blocks
44
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
cannot be erased or programmed, and can only be read by the controller instruction fetch mechanism,
protecting the contents of those blocks from being read by either the controller or by a debugger.
1.3.2.3
ROM (see page 519)
The TM4C123BE6PZ ROM is preprogrammed with the following software and programs:
■ TivaWare Peripheral Driver Library
■ TivaWare Boot Loader
■ Advanced Encryption Standard (AES) cryptography tables
■ Cyclic Redundancy Check (CRC) error-detection functionality
The TivaWare Peripheral Driver Library is a royalty-free software library for controlling on-chip
peripherals with a boot-loader capability. The library performs both peripheral initialization and
control functions, with a choice of polled or interrupt-driven peripheral support. In addition, the library
is designed to take full advantage of the stellar interrupt performance of the ARM Cortex-M4F core.
No special pragmas or custom assembly code prologue/epilogue functions are required. For
applications that require in-field programmability, the royalty-free TivaWare Boot Loader can act as
an application loader and support in-field firmware updates.
The Advanced Encryption Standard (AES) is a publicly defined encryption standard used by the
U.S. Government. AES is a strong encryption method with reasonable performance and size. In
addition, it is fast in both hardware and software, is fairly easy to implement, and requires little
memory. The Texas Instruments encryption package is available with full source code, and is based
on lesser general public license (LGPL) source. An LGPL means that the code can be used within
an application without any copyleft implications for the application (the code does not automatically
become open source). Modifications to the package source, however, must be open source.
CRC (Cyclic Redundancy Check) is a technique to validate a span of data has the same contents
as when previously checked. This technique can be used to validate correct receipt of messages
(nothing lost or modified in transit), to validate data after decompression, to validate that Flash
memory contents have not been changed, and for other cases where the data needs to be validated.
A CRC is preferred over a simple checksum (e.g. XOR all bits) because it catches changes more
readily.
1.3.2.4
EEPROM (see page 526)
The TM4C123BE6PZ microcontroller includes an EEPROM with the following features:
■ 2Kbytes of memory accessible as 512 32-bit words
■ 32 blocks of 16 words (64 bytes) each
■ Built-in wear leveling
■ Access protection per block
■ Lock protection option for the whole peripheral as well as per block using 32-bit to 96-bit unlock
codes (application selectable)
■ Interrupt support for write completion to avoid polling
July 17, 2013
45
Texas Instruments-Production Data
Architectural Overview
■ Endurance of 500K writes (when writing at fixed offset in every alternate page in circular fashion)
to 15M operations (when cycling through two pages ) per each 2-page block.
1.3.3
Serial Communications Peripherals
The TM4C123BE6PZ controller supports both asynchronous and synchronous serial communications
with:
■ Two CAN 2.0 A/B controllers
■ Eight UARTs with IrDA, 9-bit and ISO 7816 support.
– UART1 (modem flow control and modem status)
■ Six I2C modules with four transmission speeds including high-speed mode
■ Four Synchronous Serial Interface modules (SSI)
The following sections provide more detail on each of these communications functions.
1.3.3.1
Controller Area Network (CAN) (see page 1047)
Controller Area Network (CAN) is a multicast shared serial-bus standard for connecting electronic
control units (ECUs). CAN was specifically designed to be robust in electromagnetically noisy
environments and can utilize a differential balanced line like RS-485 or twisted-pair wire. Originally
created for automotive purposes, it is now used in many embedded control applications (for example,
industrial or medical). Bit rates up to 1 Mbps are possible at network lengths below 40 meters.
Decreased bit rates allow longer network distances (for example, 125 Kbps at 500m).
A transmitter sends a message to all CAN nodes (broadcasting). Each node decides on the basis
of the identifier received whether it should process the message. The identifier also determines the
priority that the message enjoys in competition for bus access. Each CAN message can transmit
from 0 to 8 bytes of user information.
The TM4C123BE6PZ microcontroller includes two CAN units with the following features:
■ CAN protocol version 2.0 part A/B
■ Bit rates up to 1 Mbps
■ 32 message objects with individual identifier masks
■ Maskable interrupt
■ Disable Automatic Retransmission mode for Time-Triggered CAN (TTCAN) applications
■ Programmable loopback mode for self-test operation
■ Programmable FIFO mode enables storage of multiple message objects
■ Gluelessly attaches to an external CAN transceiver through the CANnTX and CANnRX signals
1.3.3.2
UART (see page 892)
A Universal Asynchronous Receiver/Transmitter (UART) is an integrated circuit used for RS-232C
serial communications, containing a transmitter (parallel-to-serial converter) and a receiver
(serial-to-parallel converter), each clocked separately.
46
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
The TM4C123BE6PZ microcontroller includes eight fully programmable 16C550-type UARTs.
Although the functionality is similar to a 16C550 UART, this UART design is not register compatible.
The UART can generate individually masked interrupts from the Rx, Tx, modem flow control, modem
status, and error conditions. The module generates a single combined interrupt when any of the
interrupts are asserted and are unmasked.
The eight UARTs have the following features:
■ Programmable baud-rate generator allowing speeds up to 5 Mbps for regular speed (divide by
16) and 10 Mbps for high speed (divide by 8)
■ Separate 16x8 transmit (TX) and receive (RX) FIFOs to reduce CPU interrupt service loading
■ Programmable FIFO length, including 1-byte deep operation providing conventional
double-buffered interface
■ FIFO trigger levels of 1/8, 1/4, 1/2, 3/4, and 7/8
■ Standard asynchronous communication bits for start, stop, and parity
■ Line-break generation and detection
■ Fully programmable serial interface characteristics
– 5, 6, 7, or 8 data bits
– Even, odd, stick, or no-parity bit generation/detection
– 1 or 2 stop bit generation
■ IrDA serial-IR (SIR) encoder/decoder providing
– Programmable use of IrDA Serial Infrared (SIR) or UART input/output
– Support of IrDA SIR encoder/decoder functions for data rates up to 115.2 Kbps half-duplex
– Support of normal 3/16 and low-power (1.41-2.23 μs) bit durations
– Programmable internal clock generator enabling division of reference clock by 1 to 256 for
low-power mode bit duration
■ Support for communication with ISO 7816 smart cards
■ Modem flow control and status (on UART1)
■ EIA-485 9-bit support
■ Standard FIFO-level and End-of-Transmission interrupts
■ Efficient transfers using Micro Direct Memory Access Controller (µDMA)
– Separate channels for transmit and receive
– Receive single request asserted when data is in the FIFO; burst request asserted at
programmed FIFO level
July 17, 2013
47
Texas Instruments-Production Data
Architectural Overview
– Transmit single request asserted when there is space in the FIFO; burst request asserted at
programmed FIFO level
1.3.3.3
I2C (see page 996)
The Inter-Integrated Circuit (I2C) bus provides bi-directional data transfer through a two-wire design
(a serial data line SDA and a serial clock line SCL). The I2C bus interfaces to external I2C devices
such as serial memory (RAMs and ROMs), networking devices, LCDs, tone generators, and so on.
The I2C bus may also be used for system testing and diagnostic purposes in product development
and manufacture.
Each device on the I2C bus can be designated as either a master or a slave. I2C module supports
both sending and receiving data as either a master or a slave and can operate simultaneously as
both a master and a slave. Both the I2C master and slave can generate interrupts.
The TM4C123BE6PZ microcontroller includes six I2C modules with the following features:
■ Devices on the I2C bus can be designated as either a master or a slave
– Supports both transmitting and receiving data as either a master or a slave
– Supports simultaneous master and slave operation
■ Four I2C modes
– Master transmit
– Master receive
– Slave transmit
– Slave receive
■ Four transmission speeds:
– Standard (100 Kbps)
– Fast-mode (400 Kbps)
– Fast-mode plus (1 Mbps)
– High-speed mode (3.33 Mbps)
■ Clock low timeout interrupt
■ Dual slave address capability
■ Glitch suppression
■ Master and slave interrupt generation
– Master generates interrupts when a transmit or receive operation completes (or aborts due
to an error)
– Slave generates interrupts when data has been transferred or requested by a master or when
a START or STOP condition is detected
48
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
■ Master with arbitration and clock synchronization, multimaster support, and 7-bit addressing
mode
1.3.3.4
SSI (see page 952)
Synchronous Serial Interface (SSI) is a four-wire bi-directional communications interface that converts
data between parallel and serial. The SSI module performs serial-to-parallel conversion on data
received from a peripheral device, and parallel-to-serial conversion on data transmitted to a peripheral
device. The SSI module can be configured as either a master or slave device. As a slave device,
the SSI module can also be configured to disable its output, which allows a master device to be
coupled with multiple slave devices. The TX and RX paths are buffered with separate internal FIFOs.
The SSI module also includes a programmable bit rate clock divider and prescaler to generate the
output serial clock derived from the SSI module's input clock. Bit rates are generated based on the
input clock and the maximum bit rate is determined by the connected peripheral.
The TM4C123BE6PZ microcontroller includes four SSI modules with the following features:
■ Programmable interface operation for Freescale SPI, MICROWIRE, or Texas Instruments
synchronous serial interfaces
■ Master or slave operation
■ Programmable clock bit rate and prescaler
■ Separate transmit and receive FIFOs, each 16 bits wide and 8 locations deep
■ Programmable data frame size from 4 to 16 bits
■ Internal loopback test mode for diagnostic/debug testing
■ Standard FIFO-based interrupts and End-of-Transmission interrupt
■ Efficient transfers using Micro Direct Memory Access Controller (µDMA)
– Separate channels for transmit and receive
– Receive single request asserted when data is in the FIFO; burst request asserted when FIFO
contains 4 entries
– Transmit single request asserted when there is space in the FIFO; burst request asserted
when four or more entries are available to be written in the FIFO
1.3.4
System Integration
The TM4C123BE6PZ microcontroller provides a variety of standard system functions integrated
into the device, including:
■ Direct Memory Access Controller (DMA)
■ System control and clocks including on-chip precision 16-MHz oscillator
■ Six 32-bit timers (up to twelve 16-bit)
■ Six wide 64-bit timers (up to twelve 32-bit)
■ Twelve 32/64-bit Capture Compare PWM (CCP) pins
July 17, 2013
49
Texas Instruments-Production Data
Architectural Overview
■ Lower-power battery-backed Hibernation module
■ Real-Time Clock in Hibernation module
■ Two Watchdog Timers
– One timer runs off the main oscillator
– One timer runs off the precision internal oscillator
■ Up to 69 GPIOs, depending on configuration
– Highly flexible pin muxing allows use as GPIO or one of several peripheral functions
– Independently configurable to 2-, 4- or 8-mA drive capability
– Up to 4 GPIOs can have 18-mA drive capability
The following sections provide more detail on each of these functions.
1.3.4.1
Direct Memory Access (see page 576)
The TM4C123BE6PZ microcontroller includes a Direct Memory Access (DMA) controller, known
as micro-DMA (μDMA). The μDMA controller provides a way to offload data transfer tasks from the
Cortex-M4F processor, allowing for more efficient use of the processor and the available bus
bandwidth. The μDMA controller can perform transfers between memory and peripherals. It has
dedicated channels for each supported on-chip module and can be programmed to automatically
perform transfers between peripherals and memory as the peripheral is ready to transfer more data.
The μDMA controller provides the following features:
®
■ ARM PrimeCell 32-channel configurable µDMA controller
■ Support for memory-to-memory, memory-to-peripheral, and peripheral-to-memory in multiple
transfer modes
– Basic for simple transfer scenarios
– Ping-pong for continuous data flow
– Scatter-gather for a programmable list of up to 256 arbitrary transfers initiated from a single
request
■ Highly flexible and configurable channel operation
– Independently configured and operated channels
– Dedicated channels for supported on-chip modules
– Flexible channel assignments
– One channel each for receive and transmit path for bidirectional modules
– Dedicated channel for software-initiated transfers
– Per-channel configurable priority scheme
– Optional software-initiated requests for any channel
■ Two levels of priority
50
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
■ Design optimizations for improved bus access performance between µDMA controller and the
processor core
– µDMA controller access is subordinate to core access
– RAM striping
– Peripheral bus segmentation
■ Data sizes of 8, 16, and 32 bits
■ Transfer size is programmable in binary steps from 1 to 1024
■ Source and destination address increment size of byte, half-word, word, or no increment
■ Maskable peripheral requests
■ Interrupt on transfer completion, with a separate interrupt per channel
1.3.4.2
System Control and Clocks (see page 204)
System control determines the overall operation of the device. It provides information about the
device, controls power-saving features, controls the clocking of the device and individual peripherals,
and handles reset detection and reporting.
■ Device identification information: version, part number, SRAM size, Flash memory size, and so
on
■ Power control
– On-chip fixed Low Drop-Out (LDO) voltage regulator
– Hibernation module handles the power-up/down 3.3 V sequencing and control for the core
digital logic and analog circuits
– Low-power options for microcontroller: Sleep and Deep-sleep modes with clock gating
– Low-power options for on-chip modules: software controls shutdown of individual peripherals
and memory
– 3.3-V supply brown-out detection and reporting via interrupt or reset
■ Multiple clock sources for microcontroller system clock
– Precision Oscillator (PIOSC): On-chip resource providing a 16 MHz ±1% frequency at room
temperature
• 16 MHz ±3% across temperature
• Can be recalibrated with 7-bit trim resolution
• Software power down control for low power modes
– Main Oscillator (MOSC): A frequency-accurate clock source by one of two means: an external
single-ended clock source is connected to the OSC0 input pin, or an external crystal is
connected across the OSC0 input and OSC1 output pins.
• External crystal used with or without on-chip PLL: select supported frequencies from 4
MHz to 25 MHz.
• External oscillator: from DC to maximum device speed
July 17, 2013
51
Texas Instruments-Production Data
Architectural Overview
– Low Frequency Internal Oscillator (LFIOSC): On-chip resource used during power-saving
modes
– Hibernate RTC oscillator clock that can be configured to be the 32.768-kHz external oscillator
source from the Hibernation (HIB) module or the HIB Low Frequency clock source (HIB
LFIOSC), which is located within the Hibernation Module.
■ Flexible reset sources
– Power-on reset (POR)
– Reset pin assertion
– Brown-out reset (BOR) detector alerts to system power drops
– Software reset
– Watchdog timer reset
– MOSC failure
1.3.4.3
Programmable Timers (see page 698)
Programmable timers can be used to count or time external events that drive the Timer input pins.
Each 16/32-bit GPTM block provides two 16-bit timers/counters that can be configured to operate
independently as timers or event counters, or configured to operate as one 32-bit timer or one 32-bit
Real-Time Clock (RTC). Each 32/64-bit Wide GPTM block provides two 32-bit timers/counters that
can be configured to operate independently as timersor event counters, or configured to operate
as one 64-bit timer or one 64-bit Real-Time Clock (RTC). Timers can also be used to trigger
analog-to-digital (ADC) conversions and DMA transfers.
The General-Purpose Timer Module (GPTM) contains six 16/32-bit GPTM blocks and six 32/64-bit
Wide GPTM blocks with the following functional options:
■ 16/32-bit operating modes:
– 16- or 32-bit programmable one-shot timer
– 16- or 32-bit programmable periodic timer
– 16-bit general-purpose timer with an 8-bit prescaler
– 32-bit Real-Time Clock (RTC) when using an external 32.768-KHz clock as the input
– 16-bit input-edge count- or time-capture modes with an 8-bit prescaler
– 16-bit PWM mode with an 8-bit prescaler and software-programmable output inversion of the
PWM signal
■ 32/64-bit operating modes:
– 32- or 64-bit programmable one-shot timer
– 32- or 64-bit programmable periodic timer
– 32-bit general-purpose timer with a 16-bit prescaler
52
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
– 64-bit Real-Time Clock (RTC) when using an external 32.768-KHz clock as the input
– 32-bit input-edge count- or time-capture modes with a16-bit prescaler
– 32-bit PWM mode with a 16-bit prescaler and software-programmable output inversion of the
PWM signal
■ Count up or down
■ Twelve 16/32-bit Capture Compare PWM pins (CCP)
■ Twelve 32/64-bit Capture Compare PWM pins (CCP)
■ Daisy chaining of timer modules to allow a single timer to initiate multiple timing events
■ Timer synchronization allows selected timers to start counting on the same clock cycle
■ ADC event trigger
■ User-enabled stalling when the microcontroller asserts CPU Halt flag during debug (excluding
RTC mode)
■ Ability to determine the elapsed time between the assertion of the timer interrupt and entry into
the interrupt service routine
■ Efficient transfers using Micro Direct Memory Access Controller (µDMA)
– Dedicated channel for each timer
– Burst request generated on timer interrupt
1.3.4.4
CCP Pins (see page 707)
Capture Compare PWM pins (CCP) can be used by the General-Purpose Timer Module to time/count
external events using the CCP pin as an input. Alternatively, the GPTM can generate a simple PWM
output on the CCP pin.
The TM4C123BE6PZ microcontroller includes twelve 16/32-bit CCP pins that can be programmed
to operate in the following modes:
■ Capture: The GP Timer is incremented/decremented by programmed events on the CCP input.
The GP Timer captures and stores the current timer value when a programmed event occurs.
■ Compare: The GP Timer is incremented/decremented by programmed events on the CCP input.
The GP Timer compares the current value with a stored value and generates an interrupt when
a match occurs.
■ PWM: The GP Timer is incremented/decremented by the system clock. A PWM signal is generated
based on a match between the counter value and a value stored in a match register and is output
on the CCP pin.
1.3.4.5
Hibernation Module (HIB) (see page 486)
The Hibernation module provides logic to switch power off to the main processor and peripherals
and to wake on external or time-based events. The Hibernation module includes power-sequencing
logic and has the following features:
July 17, 2013
53
Texas Instruments-Production Data
Architectural Overview
■ 32-bit real-time seconds counter (RTC) with 1/32,768 second resolution and a 15-bit sub-seconds
counter
– 32-bit RTC seconds match register and a 15-bit sub seconds match for timed wake-up and
interrupt generation with 1/32,768 second resolution
– RTC predivider trim for making fine adjustments to the clock rate
■ Two mechanisms for power control
– System power control using discrete external regulator
– On-chip power control using internal switches under register control
■ Dedicated pin for waking using an external signal
■ RTC operational and hibernation memory valid as long as VDD or VBAT is valid
■ Low-battery detection, signaling, and interrupt generation, with optional wake on low battery
■ GPIO pin state can be retained during hibernation
■ Clock source from a 32.768-kHz external crystal or oscillator
■ Sixteen 32-bit words of battery-backed memory to save state during hibernation
■ Programmable interrupts for:
– RTC match
– External wake
– Low battery
1.3.4.6
Watchdog Timers (see page 768)
A watchdog timer is used to regain control when a system has failed due to a software error or to
the failure of an external device to respond in the expected way. The TM4C123BE6PZ Watchdog
Timer can generate an interrupt, a non-maskable interrupt, or a reset when a time-out value is
reached. In addition, the Watchdog Timer is ARM FiRM-compliant and can be configured to generate
an interrupt to the microcontroller on its first time-out, and to generate a reset signal on its second
timeout. Once the Watchdog Timer has been configured, the lock register can be written to prevent
the timer configuration from being inadvertently altered.
The TM4C123BE6PZ microcontroller has two Watchdog Timer modules: Watchdog Timer 0 uses
the system clock for its timer clock; Watchdog Timer 1 uses the PIOSC as its timer clock. The
Watchdog Timer module has the following features:
■ 32-bit down counter with a programmable load register
■ Separate watchdog clock with an enable
■ Programmable interrupt generation logic with interrupt masking and optional NMI function
■ Lock register protection from runaway software
■ Reset generation logic with an enable/disable
54
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
■ User-enabled stalling when the microcontroller asserts the CPU Halt flag during debug
1.3.4.7
Programmable GPIOs (see page 640)
General-purpose input/output (GPIO) pins offer flexibility for a variety of connections. The
TM4C123BE6PZ GPIO module is comprised of ten physical GPIO blocks, each corresponding to
an individual GPIO port. The GPIO module is FiRM-compliant (compliant to the ARM Foundation
IP for Real-Time Microcontrollers specification) and supports 0-69 programmable input/output pins.
The number of GPIOs available depends on the peripherals being used (see “Signal
Tables” on page 1217 for the signals available to each GPIO pin).
■ Up to 69 GPIOs, depending on configuration
■ Highly flexible pin muxing allows use as GPIO or one of several peripheral functions
■ 5-V-tolerant in input configuration
■ Fast toggle capable of a change every clock cycle for ports on AHB, every two clock cycles for
ports on APB
■ Programmable control for GPIO interrupts
– Interrupt generation masking
– Edge-triggered on rising, falling, or both
– Level-sensitive on High or Low values
■ Bit masking in both read and write operations through address lines
■ Can be used to initiate an ADC sample sequence or a μDMA transfer
■ Pin state can be retained during Hibernation mode
■ Pins configured as digital inputs are Schmitt-triggered
■ Programmable control for GPIO pad configuration
– Weak pull-up or pull-down resistors
– 2-mA, 4-mA, and 8-mA pad drive for digital communication; up to four pads can sink 18-mA
for high-current applications
– Slew rate control for 8-mA pad drive
– Open drain enables
– Digital input enables
1.3.5
Advanced Motion Control
The TM4C123BE6PZ microcontroller provides motion control functions integrated into the device,
including:
■ Two PWM modules, with a total of 16 advanced PWM outputs for motion and energy applications
■ Eight fault inputs to promote low-latency shutdown
July 17, 2013
55
Texas Instruments-Production Data
Architectural Overview
■ Two Quadrature Encoder Inputs (QEI)
The following provides more detail on these motion control functions.
1.3.5.1
PWM (see page 1114)
The TM4C123BE6PZ microcontroller contains two PWM modules, each with four PWM generator
blocks and a control block, for a total of 16 PWM outputs. Pulse width modulation (PWM) is a
powerful technique for digitally encoding analog signal levels. High-resolution counters are used to
generate a square wave, and the duty cycle of the square wave is modulated to encode an analog
signal. Typical applications include switching power supplies and motor control. Each
TM4C123BE6PZ PWM module consists of four PWM generator block and a control block. Each
PWM generator block contains one timer (16-bit down or up/down counter), two comparators, a
PWM signal generator, a dead-band generator, and an interrupt/ADC-trigger selector. Each PWM
generator block produces two PWM signals that can either be independent signals or a single pair
of complementary signals with dead-band delays inserted.
Each PWM generator has the following features:
■ Four fault-condition handling inputs to quickly provide low-latency shutdown and prevent damage
to the motor being controlled, for a total of eight inputs
■ One 16-bit counter
– Runs in Down or Up/Down mode
– Output frequency controlled by a 16-bit load value
– Load value updates can be synchronized
– Produces output signals at zero and load value
■ Two PWM comparators
– Comparator value updates can be synchronized
– Produces output signals on match
■ PWM signal generator
– Output PWM signal is constructed based on actions taken as a result of the counter and
PWM comparator output signals
– Produces two independent PWM signals
■ Dead-band generator
– Produces two PWM signals with programmable dead-band delays suitable for driving a half-H
bridge
– Can be bypassed, leaving input PWM signals unmodified
■ Can initiate an ADC sample sequence
56
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
The control block determines the polarity of the PWM signals and which signals are passed through
to the pins. The output of the PWM generation blocks are managed by the output control block
before being passed to the device pins. The PWM control block has the following options:
■ PWM output enable of each PWM signal
■ Optional output inversion of each PWM signal (polarity control)
■ Optional fault handling for each PWM signal
■ Synchronization of timers in the PWM generator blocks
■ Synchronization of timer/comparator updates across the PWM generator blocks
■ Extended PWM synchronization of timer/comparator updates across the PWM generator blocks
■ Interrupt status summary of the PWM generator blocks
■ Extended PWM fault handling, with multiple fault signals, programmable polarities, and filtering
■ PWM generators can be operated independently or synchronized with other generators
1.3.5.2
QEI (see page 1193)
A quadrature encoder, also known as a 2-channel incremental encoder, converts linear displacement
into a pulse signal. By monitoring both the number of pulses and the relative phase of the two signals,
the position, direction of rotation, and speed can be tracked. In addition, a third channel, or index
signal, can be used to reset the position counter. The TM4C123BE6PZ quadrature encoder with
index (QEI) module interprets the code produced by a quadrature encoder wheel to integrate position
over time and determine direction of rotation. In addition, it can capture a running estimate of the
velocity of the encoder wheel. The input frequency of the QEI inputs may be as high as 1/4 of the
processor frequency (for example, 20 MHz for a 80-MHz system).
The TM4C123BE6PZ microcontroller includes two QEI modules providing control of two motors at
the same time with the following features:
■ Position integrator that tracks the encoder position
■ Programmable noise filter on the inputs
■ Velocity capture using built-in timer
■ The input frequency of the QEI inputs may be as high as 1/4 of the processor frequency (for
example, 12.5 MHz for a 50-MHz system)
■ Interrupt generation on:
– Index pulse
– Velocity-timer expiration
– Direction change
– Quadrature error detection
July 17, 2013
57
Texas Instruments-Production Data
Architectural Overview
1.3.6
Analog
The TM4C123BE6PZ microcontroller provides analog functions integrated into the device, including:
■ Two 12-bit Analog-to-Digital Converters (ADC) with 22 analog input channels and a sample rate
of one million samples/second
■ Three analog comparators
■ 16 digital comparators
■ On-chip voltage regulator
The following provides more detail on these analog functions.
1.3.6.1
ADC (see page 793)
An analog-to-digital converter (ADC) is a peripheral that converts a continuous analog voltage to a
discrete digital number. The TM4C123BE6PZ ADC module features 12-bit conversion resolution
and supports 22 input channels plus an internal temperature sensor. Four buffered sample
sequencers allow rapid sampling of up to 22 analog input sources without controller intervention.
Each sample sequencer provides flexible programming with fully configurable input source, trigger
events, interrupt generation, and sequencer priority. Each ADC module has a digital comparator
function that allows the conversion value to be diverted to a comparison unit that provides eight
digital comparators.
The TM4C123BE6PZ microcontroller provides two ADC modules with the following features:
■ 22 shared analog input channels
■ 12-bit precision ADC
■ Single-ended and differential-input configurations
■ On-chip internal temperature sensor
■ Maximum sample rate of one million samples/second
■ Optional phase shift in sample time programmable from 22.5º to 337.5º
■ Four programmable sample conversion sequencers from one to eight entries long, with
corresponding conversion result FIFOs
■ Flexible trigger control
– Controller (software)
– Timers
– Analog Comparators
– PWM
– GPIO
■ Hardware averaging of up to 64 samples
58
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
■ Digital comparison unit providing eight digital comparators
■ Converter uses two external reference signals or VDDA and GNDA as the voltage reference
■ Power and ground for the analog circuitry is separate from the digital power and ground
■ Efficient transfers using Micro Direct Memory Access Controller (µDMA)
– Dedicated channel for each sample sequencer
– ADC module uses burst requests for DMA
1.3.6.2
Analog Comparators (see page 1098)
An analog comparator is a peripheral that compares two analog voltages and provides a logical
output that signals the comparison result. The TM4C123BE6PZ microcontroller provides three
independent integrated analog comparators that can be configured to drive an output or generate
an interrupt or ADC event.
The comparator can provide its output to a device pin, acting as a replacement for an analog
comparator on the board, or it can be used to signal the application via interrupts or triggers to the
ADC to cause it to start capturing a sample sequence. The interrupt generation and ADC triggering
logic is separate. This means, for example, that an interrupt can be generated on a rising edge and
the ADC triggered on a falling edge.
The TM4C123BE6PZ microcontroller provides three independent integrated analog comparators
with the following functions:
■ Compare external pin input to external pin input or to internal programmable voltage reference
■ Compare a test voltage against any one of the following voltages:
– An individual external reference voltage
– A shared single external reference voltage
– A shared internal reference voltage
1.3.7
JTAG and ARM Serial Wire Debug (see page 192)
The Joint Test Action Group (JTAG) port is an IEEE standard that defines a Test Access Port and
Boundary Scan Architecture for digital integrated circuits and provides a standardized serial interface
for controlling the associated test logic. The TAP, Instruction Register (IR), and Data Registers (DR)
can be used to test the interconnections of assembled printed circuit boards and obtain manufacturing
information on the components. The JTAG Port also provides a means of accessing and controlling
design-for-test features such as I/O pin observation and control, scan testing, and debugging. Texas
Instruments replaces the ARM SW-DP and JTAG-DP with the ARM Serial Wire JTAG Debug Port
(SWJ-DP) interface. The SWJ-DP interface combines the SWD and JTAG debug ports into one
module providing all the normal JTAG debug and test functionality plus real-time access to system
memory without halting the core or requiring any target resident code. The SWJ-DP interface has
the following features:
■ IEEE 1149.1-1990 compatible Test Access Port (TAP) controller
■ Four-bit Instruction Register (IR) chain for storing JTAG instructions
■ IEEE standard instructions: BYPASS, IDCODE, SAMPLE/PRELOAD, and EXTEST
July 17, 2013
59
Texas Instruments-Production Data
Architectural Overview
■ ARM additional instructions: APACC, DPACC and ABORT
■ Integrated ARM Serial Wire Debug (SWD)
– Serial Wire JTAG Debug Port (SWJ-DP)
– Flash Patch and Breakpoint (FPB) unit for implementing breakpoints
– Data Watchpoint and Trace (DWT) unit for implementing watchpoints, trigger resources, and
system profiling
– Instrumentation Trace Macrocell (ITM) for support of printf style debugging
– Embedded Trace Macrocell (ETM) for instruction trace capture
– Trace Port Interface Unit (TPIU) for bridging to a Trace Port Analyzer
1.3.8
Packaging and Temperature
■ 100-pin RoHS-compliant LQFP package
■ Industrial (-40°C to 85°C) ambient temperature range
1.4
TM4C123BE6PZ Microcontroller Hardware Details
Details on the pins and package can be found in the following sections:
■ “Pin Diagram” on page 1216
■ “Signal Tables” on page 1217
■ “Electrical Characteristics” on page 1254
■ “Package Information” on page 1296
1.5
Kits
The Tiva™ C Series provides the hardware and software tools that engineers need to begin
development quickly.
■ Reference Design Kits accelerate product development by providing ready-to-run hardware and
comprehensive documentation including hardware design files
■ Evaluation Kits provide a low-cost and effective means of evaluating TM4C123BE6PZ
microcontrollers before purchase
■ Development Kits provide you with all the tools you need to develop and prototype embedded
applications right out of the box
See the Tiva series website at http://www.ti.com/tiva-c for the latest tools available, or ask your
distributor.
1.6
Support Information
For support on Tiva™ C Series products, contact the TI Worldwide Product Information Center
nearest you.
60
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
2
The Cortex-M4F Processor
The ARM® Cortex™-M4F processor provides a high-performance, low-cost platform that meets the
system requirements of minimal memory implementation, reduced pin count, and low power
consumption, while delivering outstanding computational performance and exceptional system
response to interrupts. Features include:
®
■ 32-bit ARM Cortex™-M4F architecture optimized for small-footprint embedded applications
■ 80-MHz operation; 100 DMIPS performance
■ Outstanding processing performance combined with fast interrupt handling
■ Thumb-2 mixed 16-/32-bit instruction set delivers the high performance expected of a 32-bit
ARM core in a compact memory size usually associated with 8- and 16-bit devices, typically in
the range of a few kilobytes of memory for microcontroller-class applications
– Single-cycle multiply instruction and hardware divide
– Atomic bit manipulation (bit-banding), delivering maximum memory utilization and streamlined
peripheral control
– Unaligned data access, enabling data to be efficiently packed into memory
■ IEEE754-compliant single-precision Floating-Point Unit (FPU)
■ 16-bit SIMD vector processing unit
■ Fast code execution permits slower processor clock or increases sleep mode time
■ Harvard architecture characterized by separate buses for instruction and data
■ Efficient processor core, system and memories
■ Hardware division and fast digital-signal-processing orientated multiply accumulate
■ Saturating arithmetic for signal processing
■ Deterministic, high-performance interrupt handling for time-critical applications
■ Memory protection unit (MPU) to provide a privileged mode for protected operating system
functionality
■ Enhanced system debug with extensive breakpoint and trace capabilities
■ Serial Wire Debug and Serial Wire Trace reduce the number of pins required for debugging and
tracing
■ Migration from the ARM7™ processor family for better performance and power efficiency
■ Optimized for single-cycle Flash memory usage up to specific frequencies; see “Internal
Memory” on page 517 for more information.
■ Ultra-low power consumption with integrated sleep modes
July 17, 2013
61
Texas Instruments-Production Data
The Cortex-M4F Processor
The Tiva™ C Series microcontrollers builds on this core to bring high-performance 32-bit computing
to
This chapter provides information on the Tiva™ C Series implementation of the Cortex-M4F
processor, including the programming model, the memory model, the exception model, fault handling,
and power management.
For technical details on the instruction set, see the Cortex™-M4 instruction set chapter in the ARM®
Cortex™-M4 Devices Generic User Guide (literature number ARM DUI 0553A).
2.1
Block Diagram
The Cortex-M4F processor is built on a high-performance processor core, with a 3-stage pipeline
Harvard architecture, making it ideal for demanding embedded applications. The processor delivers
exceptional power efficiency through an efficient instruction set and extensively optimized design,
providing high-end processing hardware including IEEE754-compliant single-precision floating-point
computation, a range of single-cycle and SIMD multiplication and multiply-with-accumulate
capabilities, saturating arithmetic and dedicated hardware division.
To facilitate the design of cost-sensitive devices, the Cortex-M4F processor implements tightly
coupled system components that reduce processor area while significantly improving interrupt
handling and system debug capabilities. The Cortex-M4F processor implements a version of the
Thumb® instruction set based on Thumb-2 technology, ensuring high code density and reduced
program memory requirements. The Cortex-M4F instruction set provides the exceptional performance
expected of a modern 32-bit architecture, with the high code density of 8-bit and 16-bit
microcontrollers.
The Cortex-M4F processor closely integrates a nested interrupt controller (NVIC), to deliver
industry-leading interrupt performance. The TM4C123BE6PZ NVIC includes a non-maskable interrupt
(NMI) and provides eight interrupt priority levels. The tight integration of the processor core and
NVIC provides fast execution of interrupt service routines (ISRs), dramatically reducing interrupt
latency. The hardware stacking of registers and the ability to suspend load-multiple and store-multiple
operations further reduce interrupt latency. Interrupt handlers do not require any assembler stubs
which removes code overhead from the ISRs. Tail-chaining optimization also significantly reduces
the overhead when switching from one ISR to another. To optimize low-power designs, the NVIC
integrates with the sleep modes, including Deep-sleep mode, which enables the entire device to be
rapidly powered down.
62
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Figure 2-1. CPU Block Diagram
Nested
Vectored
Interrupt
Controller
FPU
Interrupts
Sleep
ARM
Cortex-M4F
CM4 Core
Debug
Instructions
Data
Embedded
Trace
Macrocell
Memory
Protection
Unit
Flash
Patch and
Breakpoint
Instrumentation
Data
Watchpoint Trace Macrocell
and Trace
ROM
Table
Private Peripheral
Bus
(internal)
Adv. Peripheral
Bus
Bus
Matrix
Serial Wire JTAG
Debug Port
Debug
Access Port
2.2
Overview
2.2.1
System-Level Interface
Trace
Port
Interface
Unit
Serial
Wire
Output
Trace
Port
(SWO)
I-code bus
D-code bus
System bus
The Cortex-M4F processor provides multiple interfaces using AMBA® technology to provide
high-speed, low-latency memory accesses. The core supports unaligned data accesses and
implements atomic bit manipulation that enables faster peripheral controls, system spinlocks, and
thread-safe Boolean data handling.
The Cortex-M4F processor has a memory protection unit (MPU) that provides fine-grain memory
control, enabling applications to implement security privilege levels and separate code, data and
stack on a task-by-task basis.
2.2.2
Integrated Configurable Debug
The Cortex-M4F processor implements a complete hardware debug solution, providing high system
visibility of the processor and memory through either a traditional JTAG port or a 2-pin Serial Wire
Debug (SWD) port that is ideal for microcontrollers and other small package devices. The Tiva™
C Series implementation replaces the ARM SW-DP and JTAG-DP with the ARM
CoreSight™-compliant Serial Wire JTAG Debug Port (SWJ-DP) interface. The SWJ-DP interface
combines the SWD and JTAG debug ports into one module. See the ARM® Debug Interface V5
Architecture Specification for details on SWJ-DP.
For system trace, the processor integrates an Instrumentation Trace Macrocell (ITM) alongside data
watchpoints and a profiling unit. To enable simple and cost-effective profiling of the system trace
events, a Serial Wire Viewer (SWV) can export a stream of software-generated messages, data
trace, and profiling information through a single pin.
July 17, 2013
63
Texas Instruments-Production Data
The Cortex-M4F Processor
The Embedded Trace Macrocell (ETM) delivers unrivaled instruction trace capture in an area smaller
than traditional trace units, enabling full instruction trace. For more details on the ARM ETM, see
the ARM® Embedded Trace Macrocell Architecture Specification.
The Flash Patch and Breakpoint Unit (FPB) provides up to eight hardware breakpoint comparators
that debuggers can use. The comparators in the FPB also provide remap functions for up to eight
words of program code in the code memory region. This FPB enables applications stored in a
read-only area of Flash memory to be patched in another area of on-chip SRAM or Flash memory.
If a patch is required, the application programs the FPB to remap a number of addresses. When
those addresses are accessed, the accesses are redirected to a remap table specified in the FPB
configuration.
For more information on the Cortex-M4F debug capabilities, see theARM® Debug Interface V5
Architecture Specification.
2.2.3
Trace Port Interface Unit (TPIU)
The TPIU acts as a bridge between the Cortex-M4F trace data from the ITM, and an off-chip Trace
Port Analyzer, as shown in Figure 2-2 on page 64.
Figure 2-2. TPIU Block Diagram
2.2.4
Debug
ATB
Slave
Port
ARM® Trace
Bus (ATB)
Interface
APB
Slave
Port
Advance
Peripheral
Bus (APB)
Interface
Asynchronous FIFO
Trace Out
(serializer)
Serial Wire
Trace Port
(SWO)
Cortex-M4F System Component Details
The Cortex-M4F includes the following system components:
■ SysTick
A 24-bit count-down timer that can be used as a Real-Time Operating System (RTOS) tick timer
or as a simple counter (see “System Timer (SysTick)” on page 115).
■ Nested Vectored Interrupt Controller (NVIC)
64
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
An embedded interrupt controller that supports low latency interrupt processing (see “Nested
Vectored Interrupt Controller (NVIC)” on page 116).
■ System Control Block (SCB)
The programming model interface to the processor. The SCB provides system implementation
information and system control, including configuration, control, and reporting of system exceptions
(see “System Control Block (SCB)” on page 117).
■ Memory Protection Unit (MPU)
Improves system reliability by defining the memory attributes for different memory regions. The
MPU provides up to eight different regions and an optional predefined background region (see
“Memory Protection Unit (MPU)” on page 117).
■ Floating-Point Unit (FPU)
Fully supports single-precision add, subtract, multiply, divide, multiply and accumulate, and
square-root operations. It also provides conversions between fixed-point and floating-point data
formats, and floating-point constant instructions (see “Floating-Point Unit (FPU)” on page 122).
2.3
Programming Model
This section describes the Cortex-M4F programming model. In addition to the individual core register
descriptions, information about the processor modes and privilege levels for software execution and
stacks is included.
2.3.1
Processor Mode and Privilege Levels for Software Execution
The Cortex-M4F has two modes of operation:
■ Thread mode
Used to execute application software. The processor enters Thread mode when it comes out of
reset.
■ Handler mode
Used to handle exceptions. When the processor has finished exception processing, it returns to
Thread mode.
In addition, the Cortex-M4F has two privilege levels:
■ Unprivileged
In this mode, software has the following restrictions:
– Limited access to the MSR and MRS instructions and no use of the CPS instruction
– No access to the system timer, NVIC, or system control block
– Possibly restricted access to memory or peripherals
■ Privileged
In this mode, software can use all the instructions and has access to all resources.
In Thread mode, the CONTROL register (see page 80) controls whether software execution is
privileged or unprivileged. In Handler mode, software execution is always privileged.
July 17, 2013
65
Texas Instruments-Production Data
The Cortex-M4F Processor
Only privileged software can write to the CONTROL register to change the privilege level for software
execution in Thread mode. Unprivileged software can use the SVC instruction to make a supervisor
call to transfer control to privileged software.
2.3.2
Stacks
The processor uses a full descending stack, meaning that the stack pointer indicates the last stacked
item on the memory. When the processor pushes a new item onto the stack, it decrements the stack
pointer and then writes the item to the new memory location. The processor implements two stacks:
the main stack and the process stack, with a pointer for each held in independent registers (see the
SP register on page 70).
In Thread mode, the CONTROL register (see page 80) controls whether the processor uses the
main stack or the process stack. In Handler mode, the processor always uses the main stack. The
options for processor operations are shown in Table 2-1 on page 66.
Table 2-1. Summary of Processor Mode, Privilege Level, and Stack Use
Processor Mode
Use
Privilege Level
Thread
Applications
Privileged or unprivileged
Handler
Exception handlers
Always privileged
Stack Used
a
Main stack or process stack
a
Main stack
a. See CONTROL (page 80).
2.3.3
Register Map
Figure 2-3 on page 67 shows the Cortex-M4F register set. Table 2-2 on page 67 lists the Core
registers. The core registers are not memory mapped and are accessed by register name, so the
base address is n/a (not applicable) and there is no offset.
66
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Figure 2-3. Cortex-M4F Register Set
R0
R1
R2
R3
Low registers
R4
R5
General-purpose registers
R6
R7
R8
R9
High registers
R10
R11
R12
Stack Pointer
SP (R13)
Link Register
LR (R14)
Program Counter
PC (R15)
PSP‡
PSR
MSP‡
‡
Banked version of SP
Program status register
PRIMASK
FAULTMASK
Exception mask registers
Special registers
BASEPRI
CONTROL
CONTROL register
Table 2-2. Processor Register Map
Offset
Description
See
page
Name
Type
Reset
-
R0
R/W
-
Cortex General-Purpose Register 0
69
-
R1
R/W
-
Cortex General-Purpose Register 1
69
-
R2
R/W
-
Cortex General-Purpose Register 2
69
-
R3
R/W
-
Cortex General-Purpose Register 3
69
-
R4
R/W
-
Cortex General-Purpose Register 4
69
-
R5
R/W
-
Cortex General-Purpose Register 5
69
-
R6
R/W
-
Cortex General-Purpose Register 6
69
-
R7
R/W
-
Cortex General-Purpose Register 7
69
-
R8
R/W
-
Cortex General-Purpose Register 8
69
-
R9
R/W
-
Cortex General-Purpose Register 9
69
-
R10
R/W
-
Cortex General-Purpose Register 10
69
-
R11
R/W
-
Cortex General-Purpose Register 11
69
July 17, 2013
67
Texas Instruments-Production Data
The Cortex-M4F Processor
Table 2-2. Processor Register Map (continued)
Offset
Type
Reset
-
R12
R/W
-
Cortex General-Purpose Register 12
69
-
SP
R/W
-
Stack Pointer
70
-
LR
R/W
0xFFFF.FFFF
Link Register
71
-
PC
R/W
-
Program Counter
72
-
PSR
R/W
0x0100.0000
Program Status Register
73
-
PRIMASK
R/W
0x0000.0000
Priority Mask Register
77
-
FAULTMASK
R/W
0x0000.0000
Fault Mask Register
78
-
BASEPRI
R/W
0x0000.0000
Base Priority Mask Register
79
-
CONTROL
R/W
0x0000.0000
Control Register
80
-
FPSC
R/W
-
Floating-Point Status Control
82
2.3.4
Description
See
page
Name
Register Descriptions
This section lists and describes the Cortex-M4F registers, in the order shown in Figure
2-3 on page 67. The core registers are not memory mapped and are accessed by register name
rather than offset.
Note:
The register type shown in the register descriptions refers to type during program execution
in Thread mode and Handler mode. Debug access can differ.
68
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 1: Cortex General-Purpose Register 0 (R0)
Register 2: Cortex General-Purpose Register 1 (R1)
Register 3: Cortex General-Purpose Register 2 (R2)
Register 4: Cortex General-Purpose Register 3 (R3)
Register 5: Cortex General-Purpose Register 4 (R4)
Register 6: Cortex General-Purpose Register 5 (R5)
Register 7: Cortex General-Purpose Register 6 (R6)
Register 8: Cortex General-Purpose Register 7 (R7)
Register 9: Cortex General-Purpose Register 8 (R8)
Register 10: Cortex General-Purpose Register 9 (R9)
Register 11: Cortex General-Purpose Register 10 (R10)
Register 12: Cortex General-Purpose Register 11 (R11)
Register 13: Cortex General-Purpose Register 12 (R12)
The Rn registers are 32-bit general-purpose registers for data operations and can be accessed
from either privileged or unprivileged mode.
Cortex General-Purpose Register 0 (R0)
Type R/W, reset 31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
DATA
Type
Reset
DATA
Type
Reset
Bit/Field
Name
Type
Reset
31:0
DATA
R/W
-
Description
Register data.
July 17, 2013
69
Texas Instruments-Production Data
The Cortex-M4F Processor
Register 14: Stack Pointer (SP)
The Stack Pointer (SP) is register R13. In Thread mode, the function of this register changes
depending on the ASP bit in the Control Register (CONTROL) register. When the ASP bit is clear,
this register is the Main Stack Pointer (MSP). When the ASP bit is set, this register is the Process
Stack Pointer (PSP). On reset, the ASP bit is clear, and the processor loads the MSP with the value
from address 0x0000.0000. The MSP can only be accessed in privileged mode; the PSP can be
accessed in either privileged or unprivileged mode.
Stack Pointer (SP)
Type R/W, reset 31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
SP
Type
Reset
SP
Type
Reset
Bit/Field
Name
Type
Reset
31:0
SP
R/W
-
Description
This field is the address of the stack pointer.
70
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 15: Link Register (LR)
The Link Register (LR) is register R14, and it stores the return information for subroutines, function
calls, and exceptions. The Link Register can be accessed from either privileged or unprivileged
mode.
EXC_RETURN is loaded into the LR on exception entry. See Table 2-10 on page 103 for the values
and description.
Link Register (LR)
Type R/W, reset 0xFFFF.FFFF
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
7
6
5
4
3
2
1
0
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
LINK
Type
Reset
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
15
14
13
12
11
10
9
8
LINK
Type
Reset
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
Bit/Field
Name
Type
31:0
LINK
R/W
R/W
1
Reset
R/W
1
Description
0xFFFF.FFFF This field is the return address.
July 17, 2013
71
Texas Instruments-Production Data
The Cortex-M4F Processor
Register 16: Program Counter (PC)
The Program Counter (PC) is register R15, and it contains the current program address. On reset,
the processor loads the PC with the value of the reset vector, which is at address 0x0000.0004. Bit
0 of the reset vector is loaded into the THUMB bit of the EPSR at reset and must be 1. The PC register
can be accessed in either privileged or unprivileged mode.
Program Counter (PC)
Type R/W, reset 31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
PC
Type
Reset
PC
Type
Reset
Bit/Field
Name
Type
Reset
31:0
PC
R/W
-
Description
This field is the current program address.
72
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 17: Program Status Register (PSR)
Note:
This register is also referred to as xPSR.
The Program Status Register (PSR) has three functions, and the register bits are assigned to the
different functions:
■ Application Program Status Register (APSR), bits 31:27, bits 19:16
■ Execution Program Status Register (EPSR), bits 26:24, 15:10
■ Interrupt Program Status Register (IPSR), bits 7:0
The PSR, IPSR, and EPSR registers can only be accessed in privileged mode; the APSR register
can be accessed in either privileged or unprivileged mode.
APSR contains the current state of the condition flags from previous instruction executions.
EPSR contains the Thumb state bit and the execution state bits for the If-Then (IT) instruction or
the Interruptible-Continuable Instruction (ICI) field for an interrupted load multiple or store multiple
instruction. Attempts to read the EPSR directly through application software using the MSR instruction
always return zero. Attempts to write the EPSR using the MSR instruction in application software
are always ignored. Fault handlers can examine the EPSR value in the stacked PSR to determine
the operation that faulted (see “Exception Entry and Return” on page 100).
IPSR contains the exception type number of the current Interrupt Service Routine (ISR).
These registers can be accessed individually or as a combination of any two or all three registers,
using the register name as an argument to the MSR or MRS instructions. For example, all of the
registers can be read using PSR with the MRS instruction, or APSR only can be written to using
APSR with the MSR instruction. page 73 shows the possible register combinations for the PSR. See
the MRS and MSR instruction descriptions in the Cortex™-M4 instruction set chapter in the ARM®
Cortex™-M4 Devices Generic User Guide (literature number ARM DUI 0553A) for more information
about how to access the program status registers.
Table 2-3. PSR Register Combinations
Register
Type
PSR
R/W
Combination
APSR, EPSR, and IPSR
IEPSR
RO
EPSR and IPSR
a, b
a
APSR and IPSR
b
APSR and EPSR
IAPSR
R/W
EAPSR
R/W
a. The processor ignores writes to the IPSR bits.
b. Reads of the EPSR bits return zero, and the processor ignores writes to these bits.
Program Status Register (PSR)
Type R/W, reset 0x0100.0000
Type
Reset
31
30
29
28
27
N
Z
C
V
Q
26
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
RO
0
RO
0
RO
1
RO
0
RO
0
RO
0
RO
0
R/W
0
15
14
13
12
11
10
9
8
7
6
5
4
ICI / IT
Type
Reset
RO
0
RO
0
RO
0
25
ICI / IT
24
23
22
THUMB
21
RO
0
RO
0
RO
0
RO
0
19
18
17
16
R/W
0
R/W
0
R/W
0
3
2
1
0
RO
0
RO
0
RO
0
RO
0
GE
reserved
RO
0
20
reserved
ISRNUM
RO
0
RO
0
July 17, 2013
RO
0
RO
0
73
Texas Instruments-Production Data
The Cortex-M4F Processor
Bit/Field
Name
Type
Reset
31
N
R/W
0
Description
APSR Negative or Less Flag
Value Description
1
The previous operation result was negative or less than.
0
The previous operation result was positive, zero, greater than,
or equal.
The value of this bit is only meaningful when accessing PSR or APSR.
30
Z
R/W
0
APSR Zero Flag
Value Description
1
The previous operation result was zero.
0
The previous operation result was non-zero.
The value of this bit is only meaningful when accessing PSR or APSR.
29
C
R/W
0
APSR Carry or Borrow Flag
Value Description
1
The previous add operation resulted in a carry bit or the previous
subtract operation did not result in a borrow bit.
0
The previous add operation did not result in a carry bit or the
previous subtract operation resulted in a borrow bit.
The value of this bit is only meaningful when accessing PSR or APSR.
28
V
R/W
0
APSR Overflow Flag
Value Description
1
The previous operation resulted in an overflow.
0
The previous operation did not result in an overflow.
The value of this bit is only meaningful when accessing PSR or APSR.
27
Q
R/W
0
APSR DSP Overflow and Saturation Flag
Value Description
1
DSP Overflow or saturation has occurred when using a SIMD
instruction.
0
DSP overflow or saturation has not occurred since reset or since
the bit was last cleared.
The value of this bit is only meaningful when accessing PSR or APSR.
This bit is cleared by software using an MRS instruction.
74
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
26:25
ICI / IT
RO
0x0
Description
EPSR ICI / IT status
These bits, along with bits 15:10, contain the Interruptible-Continuable
Instruction (ICI) field for an interrupted load multiple or store multiple
instruction or the execution state bits of the IT instruction.
When EPSR holds the ICI execution state, bits 26:25 are zero.
The If-Then block contains up to four instructions following an IT
instruction. Each instruction in the block is conditional. The conditions
for the instructions are either all the same, or some can be the inverse
of others. See the Cortex™-M4 instruction set chapter in the ARM®
Cortex™-M4 Devices Generic User Guide (literature number ARM DUI
0553A) for more information.
The value of this field is only meaningful when accessing PSR or EPSR.
Note that these EPSR bits cannot be accessed using MRS and MSR
instructions but the definitions are provided to allow the stacked (E)PSR
value to be decoded within an exception handler.
24
THUMB
RO
1
EPSR Thumb State
This bit indicates the Thumb state and should always be set.
The following can clear the THUMB bit:
■
The BLX, BX and POP{PC} instructions
■
Restoration from the stacked xPSR value on an exception return
■
Bit 0 of the vector value on an exception entry or reset
Attempting to execute instructions when this bit is clear results in a fault
or lockup. See “Lockup” on page 105 for more information.
The value of this bit is only meaningful when accessing PSR or EPSR.
23:20
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
19:16
GE
R/W
0x0
Greater Than or Equal Flags
See the description of the SEL instruction in the Cortex™-M4 instruction
set chapter in the ARM® Cortex™-M4 Devices Generic User Guide
(literature number ARM DUI 0553A) for more information.
The value of this field is only meaningful when accessing PSR or APSR.
July 17, 2013
75
Texas Instruments-Production Data
The Cortex-M4F Processor
Bit/Field
Name
Type
Reset
15:10
ICI / IT
RO
0x0
Description
EPSR ICI / IT status
These bits, along with bits 26:25, contain the Interruptible-Continuable
Instruction (ICI) field for an interrupted load multiple or store multiple
instruction or the execution state bits of the IT instruction.
When an interrupt occurs during the execution of an LDM, STM, PUSH
POP, VLDM, VSTM, VPUSH, or VPOP instruction, the processor stops the
load multiple or store multiple instruction operation temporarily and
stores the next register operand in the multiple operation to bits 15:12.
After servicing the interrupt, the processor returns to the register pointed
to by bits 15:12 and resumes execution of the multiple load or store
instruction. When EPSR holds the ICI execution state, bits 11:10 are
zero.
The If-Then block contains up to four instructions following a 16-bit IT
instruction. Each instruction in the block is conditional. The conditions
for the instructions are either all the same, or some can be the inverse
of others. See the Cortex™-M4 instruction set chapter in the ARM®
Cortex™-M4 Devices Generic User Guide (literature number ARM DUI
0553A) for more information.
The value of this field is only meaningful when accessing PSR or EPSR.
9:8
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7:0
ISRNUM
RO
0x00
IPSR ISR Number
This field contains the exception type number of the current Interrupt
Service Routine (ISR).
Value
Description
0x00
Thread mode
0x01
Reserved
0x02
NMI
0x03
Hard fault
0x04
Memory management fault
0x05
Bus fault
0x06
Usage fault
0x07-0x0A Reserved
0x0B
SVCall
0x0C
Reserved for Debug
0x0D
Reserved
0x0E
PendSV
0x0F
SysTick
0x10
Interrupt Vector 0
0x11
Interrupt Vector 1
...
...
0x9A
Interrupt Vector 138
See “Exception Types” on page 94 for more information.
The value of this field is only meaningful when accessing PSR or IPSR.
76
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 18: Priority Mask Register (PRIMASK)
The PRIMASK register prevents activation of all exceptions with programmable priority. Reset,
non-maskable interrupt (NMI), and hard fault are the only exceptions with fixed priority. Exceptions
should be disabled when they might impact the timing of critical tasks. This register is only accessible
in privileged mode. The MSR and MRS instructions are used to access the PRIMASK register, and
the CPS instruction may be used to change the value of the PRIMASK register. See the Cortex™-M4
instruction set chapter in the ARM® Cortex™-M4 Devices Generic User Guide (literature number
ARM DUI 0553A) for more information on these instructions. For more information on exception
priority levels, see “Exception Types” on page 94.
Priority Mask Register (PRIMASK)
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0x0000.000
0
PRIMASK
R/W
0
RO
0
PRIMASK
R/W
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Priority Mask
Value Description
1
Prevents the activation of all exceptions with configurable
priority.
0
No effect.
July 17, 2013
77
Texas Instruments-Production Data
The Cortex-M4F Processor
Register 19: Fault Mask Register (FAULTMASK)
The FAULTMASK register prevents activation of all exceptions except for the Non-Maskable Interrupt
(NMI). Exceptions should be disabled when they might impact the timing of critical tasks. This register
is only accessible in privileged mode. The MSR and MRS instructions are used to access the
FAULTMASK register, and the CPS instruction may be used to change the value of the FAULTMASK
register. See the Cortex™-M4 instruction set chapter in the ARM® Cortex™-M4 Devices Generic
User Guide (literature number ARM DUI 0553A) for more information on these instructions. For
more information on exception priority levels, see “Exception Types” on page 94.
Fault Mask Register (FAULTMASK)
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0x0000.000
0
FAULTMASK
R/W
0
RO
0
FAULTMASK
R/W
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Fault Mask
Value Description
1
Prevents the activation of all exceptions except for NMI.
0
No effect.
The processor clears the FAULTMASK bit on exit from any exception
handler except the NMI handler.
78
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 20: Base Priority Mask Register (BASEPRI)
The BASEPRI register defines the minimum priority for exception processing. When BASEPRI is
set to a nonzero value, it prevents the activation of all exceptions with the same or lower priority
level as the BASEPRI value. Exceptions should be disabled when they might impact the timing of
critical tasks. This register is only accessible in privileged mode. For more information on exception
priority levels, see “Exception Types” on page 94.
Base Priority Mask Register (BASEPRI)
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RO
0
R/W
0
R/W
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
BASEPRI
RO
0
Bit/Field
Name
Type
Reset
31:8
reserved
RO
0x0000.00
7:5
BASEPRI
R/W
0x0
R/W
0
reserved
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Base Priority
Any exception that has a programmable priority level with the same or
lower priority as the value of this field is masked. The PRIMASK register
can be used to mask all exceptions with programmable priority levels.
Higher priority exceptions have lower priority levels.
Value Description
4:0
reserved
RO
0x0
0x0
All exceptions are unmasked.
0x1
All exceptions with priority level 1-7 are masked.
0x2
All exceptions with priority level 2-7 are masked.
0x3
All exceptions with priority level 3-7 are masked.
0x4
All exceptions with priority level 4-7 are masked.
0x5
All exceptions with priority level 5-7 are masked.
0x6
All exceptions with priority level 6-7 are masked.
0x7
All exceptions with priority level 7 are masked.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
79
Texas Instruments-Production Data
The Cortex-M4F Processor
Register 21: Control Register (CONTROL)
The CONTROL register controls the stack used and the privilege level for software execution when
the processor is in Thread mode, and indicates whether the FPU state is active. This register is only
accessible in privileged mode.
Handler mode always uses the MSP, so the processor ignores explicit writes to the ASP bit of the
CONTROL register when in Handler mode. The exception entry and return mechanisms automatically
update the CONTROL register based on the EXC_RETURN value (see Table 2-10 on page 103).
In an OS environment, threads running in Thread mode should use the process stack and the kernel
and exception handlers should use the main stack. By default, Thread mode uses the MSP. To
switch the stack pointer used in Thread mode to the PSP, either use the MSR instruction to set the
ASP bit, as detailed in the Cortex™-M4 instruction set chapter in the ARM® Cortex™-M4 Devices
Generic User Guide (literature number ARM DUI 0553A), or perform an exception return to Thread
mode with the appropriate EXC_RETURN value, as shown in Table 2-10 on page 103.
Note:
When changing the stack pointer, software must use an ISB instruction immediately after
the MSR instruction, ensuring that instructions after the ISB execute use the new stack
pointer. See the Cortex™-M4 instruction set chapter in the ARM® Cortex™-M4 Devices
Generic User Guide (literature number ARM DUI 0553A).
Control Register (CONTROL)
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
FPCA
ASP
TMPL
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
31:3
reserved
RO
0x0000.000
2
FPCA
R/W
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Floating-Point Context Active
Value Description
1
Floating-point context active
0
No floating-point context active
The Cortex-M4F uses this bit to determine whether to preserve
floating-point state when processing an exception.
Important:
Two bits control when FPCA can be enabled: the ASPEN
bit in the Floating-Point Context Control (FPCC)
register and the DISFPCA bit in the Auxiliary Control
(ACTLR) register.
80
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
1
ASP
R/W
0
Description
Active Stack Pointer
Value Description
1
The PSP is the current stack pointer.
0
The MSP is the current stack pointer
In Handler mode, this bit reads as zero and ignores writes. The
Cortex-M4F updates this bit automatically on exception return.
0
TMPL
R/W
0
Thread Mode Privilege Level
Value Description
1
Unprivileged software can be executed in Thread mode.
0
Only privileged software can be executed in Thread mode.
July 17, 2013
81
Texas Instruments-Production Data
The Cortex-M4F Processor
Register 22: Floating-Point Status Control (FPSC)
The FPSC register provides all necessary user-level control of the floating-point system.
Floating-Point Status Control (FPSC)
Type R/W, reset 31
Type
Reset
30
29
28
27
26
25
24
22
21
20
19
RMODE
18
17
16
N
Z
C
V
reserved
AHP
DN
FZ
R/W
-
R/W
-
R/W
-
R/W
-
RO
0
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
IXC
UFC
OFC
DZC
IOC
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
-
RO
0
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
reserved
Type
Reset
23
IDC
RO
0
Bit/Field
Name
Type
Reset
31
N
R/W
-
reserved
reserved
RO
0
Description
Negative Condition Code Flag
Floating-point comparison operations update this condition code flag.
30
Z
R/W
-
Zero Condition Code Flag
Floating-point comparison operations update this condition code flag.
29
C
R/W
-
Carry Condition Code Flag
Floating-point comparison operations update this condition code flag.
28
V
R/W
-
Overflow Condition Code Flag
Floating-point comparison operations update this condition code flag.
27
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
26
AHP
R/W
-
Alternative Half-Precision
When set, alternative half-precision format is selected. When clear,
IEEE half-precision format is selected.
The AHP bit in the FPDSC register holds the default value for this bit.
25
DN
R/W
-
Default NaN Mode
When set, any operation involving one or more NaNs returns the Default
NaN. When clear, NaN operands propagate through to the output of a
floating-point operation.
The DN bit in the FPDSC register holds the default value for this bit.
24
FZ
R/W
-
Flush-to-Zero Mode
When set, Flush-to-Zero mode is enabled. When clear, Flush-to-Zero
mode is disabled and the behavior of the floating-point system is fully
compliant with the IEEE 754 standard.
The FZ bit in the FPDSC register holds the default value for this bit.
82
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
23:22
RMODE
R/W
-
Description
Rounding Mode
The specified rounding mode is used by almost all floating-point
instructions.
The RMODE bit in the FPDSC register holds the default value for this bit.
Value Description
21:8
reserved
RO
0x0
7
IDC
R/W
-
0x0
Round to Nearest (RN) mode
0x1
Round towards Plus Infinity (RP) mode
0x2
Round towards Minus Infinity (RM) mode
0x3
Round towards Zero (RZ) mode
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Input Denormal Cumulative Exception
When set, indicates this exception has occurred since 0 was last written
to this bit.
6:5
reserved
RO
0x0
4
IXC
R/W
-
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Inexact Cumulative Exception
When set, indicates this exception has occurred since 0 was last written
to this bit.
3
UFC
R/W
-
Underflow Cumulative Exception
When set, indicates this exception has occurred since 0 was last written
to this bit.
2
OFC
R/W
-
Overflow Cumulative Exception
When set, indicates this exception has occurred since 0 was last written
to this bit.
1
DZC
R/W
-
Division by Zero Cumulative Exception
When set, indicates this exception has occurred since 0 was last written
to this bit.
0
IOC
R/W
-
Invalid Operation Cumulative Exception
When set, indicates this exception has occurred since 0 was last written
to this bit.
July 17, 2013
83
Texas Instruments-Production Data
The Cortex-M4F Processor
2.3.5
Exceptions and Interrupts
The Cortex-M4F processor supports interrupts and system exceptions. The processor and the
Nested Vectored Interrupt Controller (NVIC) prioritize and handle all exceptions. An exception
changes the normal flow of software control. The processor uses Handler mode to handle all
exceptions except for reset. See “Exception Entry and Return” on page 100 for more information.
The NVIC registers control interrupt handling. See “Nested Vectored Interrupt Controller
(NVIC)” on page 116 for more information.
2.3.6
Data Types
The Cortex-M4F supports 32-bit words, 16-bit halfwords, and 8-bit bytes. The processor also supports
64-bit data transfer instructions. All instruction and data memory accesses are little endian. See
“Memory Regions, Types and Attributes” on page 87 for more information.
2.4
Memory Model
This section describes the processor memory map, the behavior of memory accesses, and the
bit-banding features. The processor has a fixed memory map that provides up to 4 GB of addressable
memory.
The memory map for the TM4C123BE6PZ controller is provided in Table 2-4 on page 84. In this
manual, register addresses are given as a hexadecimal increment, relative to the module’s base
address as shown in the memory map.
The regions for SRAM and peripherals include bit-band regions. Bit-banding provides atomic
operations to bit data (see “Bit-Banding” on page 89).
The processor reserves regions of the Private peripheral bus (PPB) address range for core peripheral
registers (see “Cortex-M4 Peripherals” on page 114).
Note:
Within the memory map, attempts to read or write addresses in reserved spaces result in
a bus fault. In addition, attempts to write addresses in the flash range also result in a bus
fault.
Table 2-4. Memory Map
Start
End
Description
For details,
see page ...
0x0000.0000
0x0001.FFFF
On-chip Flash
533
0x0002.0000
0x00FF.FFFF
Reserved
-
0x0100.0000
0x1FFF.FFFF
Reserved for ROM
519
0x2000.0000
0x2000.7FFF
Bit-banded on-chip SRAM
518
0x2000.8000
0x21FF.FFFF
Reserved
-
0x2200.0000
0x220F.FFFF
Bit-band alias of bit-banded on-chip SRAM starting at
0x2000.0000
518
0x2210.0000
0x3FFF.FFFF
Reserved
-
0x4000.0000
0x4000.0FFF
Watchdog timer 0
771
0x4000.1000
0x4000.1FFF
Watchdog timer 1
771
0x4000.2000
0x4000.3FFF
Reserved
-
0x4000.4000
0x4000.4FFF
GPIO Port A
653
Memory
Peripherals
84
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Table 2-4. Memory Map (continued)
Start
End
Description
For details,
see page ...
0x4000.5000
0x4000.5FFF
GPIO Port B
653
0x4000.6000
0x4000.6FFF
GPIO Port C
653
0x4000.7000
0x4000.7FFF
GPIO Port D
653
0x4000.8000
0x4000.8FFF
SSI0
967
0x4000.9000
0x4000.9FFF
SSI1
967
0x4000.A000
0x4000.AFFF
SSI2
967
0x4000.B000
0x4000.BFFF
SSI3
967
0x4000.C000
0x4000.CFFF
UART0
904
0x4000.D000
0x4000.DFFF
UART1
904
0x4000.E000
0x4000.EFFF
UART2
904
0x4000.F000
0x4000.FFFF
UART3
904
0x4001.0000
0x4001.0FFF
UART4
904
0x4001.1000
0x4001.1FFF
UART5
904
0x4001.2000
0x4001.2FFF
UART6
904
0x4001.3000
0x4001.3FFF
UART7
904
0x4001.4000
0x4001.FFFF
Reserved
-
0x4002.0000
0x4002.0FFF
I2C 0
1017
0x4002.1000
0x4002.1FFF
I2C 1
1017
0x4002.2FFF
I2C
2
1017
0x4002.3000
0x4002.3FFF
I2C
3
1017
0x4002.4000
0x4002.4FFF
GPIO Port E
653
0x4002.5000
0x4002.5FFF
GPIO Port F
653
0x4002.6000
0x4002.6FFF
GPIO Port G
653
0x4002.7000
0x4002.7FFF
GPIO Port H
653
0x4002.8000
0x4002.8FFF
PWM 0
1128
0x4002.9000
0x4002.9FFF
PWM 1
1128
0x4002.A000
0x4002.BFFF
Reserved
-
0x4002.C000
0x4002.CFFF
QEI0
1199
0x4002.D000
0x4002.DFFF
QEI1
1199
0x4002.E000
0x4002.FFFF
Reserved
-
0x4003.0000
0x4003.0FFF
16/32-bit Timer 0
720
0x4003.1000
0x4003.1FFF
16/32-bit Timer 1
720
0x4003.2000
0x4003.2FFF
16/32-bit Timer 2
720
0x4003.3000
0x4003.3FFF
16/32-bit Timer 3
720
0x4003.4000
0x4003.4FFF
16/32-bit Timer 4
720
0x4003.5000
0x4003.5FFF
16/32-bit Timer 5
720
0x4003.6000
0x4003.6FFF
32/64-bit Timer 0
720
0x4003.7000
0x4003.7FFF
32/64-bit Timer 1
720
0x4003.8000
0x4003.8FFF
ADC0
814
0x4003.9000
0x4003.9FFF
ADC1
814
Peripherals
0x4002.2000
July 17, 2013
85
Texas Instruments-Production Data
The Cortex-M4F Processor
Table 2-4. Memory Map (continued)
Start
End
Description
For details,
see page ...
0x4003.A000
0x4003.BFFF
Reserved
-
0x4003.C000
0x4003.CFFF
Analog Comparators
1098
0x4003.D000
0x4003.DFFF
GPIO Port J
653
0x4003.E000
0x4003.FFFF
Reserved
-
0x4004.0000
0x4004.0FFF
CAN0 Controller
1067
0x4004.1000
0x4004.1FFF
CAN1 Controller
1067
0x4004.2000
0x4004.BFFF
Reserved
-
0x4004.C000
0x4004.CFFF
32/64-bit Timer 2
720
0x4004.D000
0x4004.DFFF
32/64-bit Timer 3
720
0x4004.E000
0x4004.EFFF
32/64-bit Timer 4
720
0x4004.F000
0x4004.FFFF
32/64-bit Timer 5
720
0x4005.0000
0x4005.7FFF
Reserved
-
0x4005.8000
0x4005.8FFF
GPIO Port A (AHB aperture)
653
0x4005.9000
0x4005.9FFF
GPIO Port B (AHB aperture)
653
0x4005.A000
0x4005.AFFF
GPIO Port C (AHB aperture)
653
0x4005.B000
0x4005.BFFF
GPIO Port D (AHB aperture)
653
0x4005.C000
0x4005.CFFF
GPIO Port E (AHB aperture)
653
0x4005.D000
0x4005.DFFF
GPIO Port F (AHB aperture)
653
0x4005.E000
0x4005.EFFF
GPIO Port G (AHB aperture)
653
0x4005.F000
0x4005.FFFF
GPIO Port H (AHB aperture)
653
0x4006.0000
0x4006.0FFF
GPIO Port J (AHB aperture)
653
0x4006.1000
0x4006.1FFF
GPIO Port K (AHB aperture)
653
0x4006.2000
0x400A.EFFF
Reserved
-
0x400A.F000
0x400A.FFFF
EEPROM and Key Locker
551
0x400B.0000
0x400B.FFFF
Reserved
-
0x400C.0000
0x400C.0FFF
I2C 4
1017
0x400C.1000
0x400C.1FFF
I2C
1017
0x400C.2000
0x400F.8FFF
Reserved
-
0x400F.9000
0x400F.9FFF
System Exception Module
478
0x400F.A000
0x400F.BFFF
Reserved
-
0x400F.C000
0x400F.CFFF
Hibernation Module
499
0x400F.D000
0x400F.DFFF
Flash memory control
533
0x400F.E000
0x400F.EFFF
System control
228
0x400F.F000
0x400F.FFFF
µDMA
597
0x4010.0000
0x41FF.FFFF
Reserved
-
0x4200.0000
0x43FF.FFFF
Bit-banded alias of 0x4000.0000 through 0x400F.FFFF
-
0x4400.0000
0xDFFF.FFFF
Reserved
-
0xE000.0000
0xE000.0FFF
Instrumentation Trace Macrocell (ITM)
63
0xE000.1000
0xE000.1FFF
Data Watchpoint and Trace (DWT)
63
0xE000.2000
0xE000.2FFF
Flash Patch and Breakpoint (FPB)
63
5
Private Peripheral Bus
86
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Table 2-4. Memory Map (continued)
Start
End
Description
For details,
see page ...
0xE000.3000
0xE000.DFFF
Reserved
-
0xE000.E000
0xE000.EFFF
Cortex-M4F Peripherals (SysTick, NVIC, MPU, FPU and SCB) 126
0xE000.F000
0xE003.FFFF
Reserved
-
0xE004.0000
0xE004.0FFF
Trace Port Interface Unit (TPIU)
64
0xE004.1000
0xE004.1FFF
Embedded Trace Macrocell (ETM)
63
0xE004.2000
0xFFFF.FFFF
Reserved
-
2.4.1
Memory Regions, Types and Attributes
The memory map and the programming of the MPU split the memory map into regions. Each region
has a defined memory type, and some regions have additional memory attributes. The memory
type and attributes determine the behavior of accesses to the region.
The memory types are:
■ Normal: The processor can re-order transactions for efficiency and perform speculative reads.
■ Device: The processor preserves transaction order relative to other transactions to Device or
Strongly Ordered memory.
■ Strongly Ordered: The processor preserves transaction order relative to all other transactions.
The different ordering requirements for Device and Strongly Ordered memory mean that the memory
system can buffer a write to Device memory but must not buffer a write to Strongly Ordered memory.
An additional memory attribute is Execute Never (XN), which means the processor prevents
instruction accesses. A fault exception is generated only on execution of an instruction executed
from an XN region.
2.4.2
Memory System Ordering of Memory Accesses
For most memory accesses caused by explicit memory access instructions, the memory system
does not guarantee that the order in which the accesses complete matches the program order of
the instructions, providing the order does not affect the behavior of the instruction sequence. Normally,
if correct program execution depends on two memory accesses completing in program order,
software must insert a memory barrier instruction between the memory access instructions (see
“Software Ordering of Memory Accesses” on page 88).
However, the memory system does guarantee ordering of accesses to Device and Strongly Ordered
memory. For two memory access instructions A1 and A2, if both A1 and A2 are accesses to either
Device or Strongly Ordered memory, and if A1 occurs before A2 in program order, A1 is always
observed before A2.
2.4.3
Behavior of Memory Accesses
Table 2-5 on page 88 shows the behavior of accesses to each region in the memory map. See
“Memory Regions, Types and Attributes” on page 87 for more information on memory types and
the XN attribute. Tiva™ C Series devices may have reserved memory areas within the address
ranges shown below (refer to Table 2-4 on page 84 for more information).
July 17, 2013
87
Texas Instruments-Production Data
The Cortex-M4F Processor
Table 2-5. Memory Access Behavior
Address Range
Memory Region
Memory Type
Execute
Never
(XN)
Description
0x0000.0000 - 0x1FFF.FFFF Code
Normal
-
This executable region is for program code.
Data can also be stored here.
0x2000.0000 - 0x3FFF.FFFF SRAM
Normal
-
This executable region is for data. Code
can also be stored here. This region
includes bit band and bit band alias areas
(see Table 2-6 on page 90).
0x4000.0000 - 0x5FFF.FFFF Peripheral
Device
XN
This region includes bit band and bit band
alias areas (see Table 2-7 on page 90).
0x6000.0000 - 0x9FFF.FFFF External RAM
Normal
-
This executable region is for data.
0xA000.0000 - 0xDFFF.FFFF External device
Device
XN
This region is for external device memory.
0xE000.0000- 0xE00F.FFFF Private peripheral
bus
Strongly
Ordered
XN
This region includes the NVIC, system
timer, and system control block.
0xE010.0000- 0xFFFF.FFFF Reserved
-
-
-
The Code, SRAM, and external RAM regions can hold programs. However, it is recommended that
programs always use the Code region because the Cortex-M4F has separate buses that can perform
instruction fetches and data accesses simultaneously.
The MPU can override the default memory access behavior described in this section. For more
information, see “Memory Protection Unit (MPU)” on page 117.
The Cortex-M4F prefetches instructions ahead of execution and speculatively prefetches from
branch target addresses.
2.4.4
Software Ordering of Memory Accesses
The order of instructions in the program flow does not always guarantee the order of the
corresponding memory transactions for the following reasons:
■ The processor can reorder some memory accesses to improve efficiency, providing this does
not affect the behavior of the instruction sequence.
■ The processor has multiple bus interfaces.
■ Memory or devices in the memory map have different wait states.
■ Some memory accesses are buffered or speculative.
“Memory System Ordering of Memory Accesses” on page 87 describes the cases where the memory
system guarantees the order of memory accesses. Otherwise, if the order of memory accesses is
critical, software must include memory barrier instructions to force that ordering. The Cortex-M4F
has the following memory barrier instructions:
■ The Data Memory Barrier (DMB) instruction ensures that outstanding memory transactions
complete before subsequent memory transactions.
■ The Data Synchronization Barrier (DSB) instruction ensures that outstanding memory transactions
complete before subsequent instructions execute.
■ The Instruction Synchronization Barrier (ISB) instruction ensures that the effect of all completed
memory transactions is recognizable by subsequent instructions.
88
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Memory barrier instructions can be used in the following situations:
■ MPU programming
– If the MPU settings are changed and the change must be effective on the very next instruction,
use a DSB instruction to ensure the effect of the MPU takes place immediately at the end of
context switching.
– Use an ISB instruction to ensure the new MPU setting takes effect immediately after
programming the MPU region or regions, if the MPU configuration code was accessed using
a branch or call. If the MPU configuration code is entered using exception mechanisms, then
an ISB instruction is not required.
■ Vector table
If the program changes an entry in the vector table and then enables the corresponding exception,
use a DMB instruction between the operations. The DMB instruction ensures that if the exception
is taken immediately after being enabled, the processor uses the new exception vector.
■ Self-modifying code
If a program contains self-modifying code, use an ISB instruction immediately after the code
modification in the program. The ISB instruction ensures subsequent instruction execution uses
the updated program.
■ Memory map switching
If the system contains a memory map switching mechanism, use a DSB instruction after switching
the memory map in the program. The DSB instruction ensures subsequent instruction execution
uses the updated memory map.
■ Dynamic exception priority change
When an exception priority has to change when the exception is pending or active, use DSB
instructions after the change. The change then takes effect on completion of the DSB instruction.
Memory accesses to Strongly Ordered memory, such as the System Control Block, do not require
the use of DMB instructions.
For more information on the memory barrier instructions, see the Cortex™-M4 instruction set chapter
in the ARM® Cortex™-M4 Devices Generic User Guide (literature number ARM DUI 0553A).
2.4.5
Bit-Banding
A bit-band region maps each word in a bit-band alias region to a single bit in the bit-band region.
The bit-band regions occupy the lowest 1 MB of the SRAM and peripheral memory regions. Accesses
to the 32-MB SRAM alias region map to the 1-MB SRAM bit-band region, as shown in Table
2-6 on page 90. Accesses to the 32-MB peripheral alias region map to the 1-MB peripheral bit-band
region, as shown in Table 2-7 on page 90. For the specific address range of the bit-band regions,
see Table 2-4 on page 84.
Note:
A word access to the SRAM or the peripheral bit-band alias region maps to a single bit in
the SRAM or peripheral bit-band region.
A word access to a bit band address results in a word access to the underlying memory,
and similarly for halfword and byte accesses. This allows bit band accesses to match the
access requirements of the underlying peripheral.
July 17, 2013
89
Texas Instruments-Production Data
The Cortex-M4F Processor
Table 2-6. SRAM Memory Bit-Banding Regions
Address Range
Memory Region
Instruction and Data Accesses
Start
End
0x2000.0000
0x2000.7FFF
SRAM bit-band region Direct accesses to this memory range behave as SRAM
memory accesses, but this region is also bit addressable
through bit-band alias.
0x2200.0000
0x220F.FFFF
SRAM bit-band alias
Data accesses to this region are remapped to bit band
region. A write operation is performed as
read-modify-write. Instruction accesses are not remapped.
Table 2-7. Peripheral Memory Bit-Banding Regions
Address Range
Memory Region
Instruction and Data Accesses
0x400F.FFFF
Peripheral bit-band
region
Direct accesses to this memory range behave as
peripheral memory accesses, but this region is also bit
addressable through bit-band alias.
0x43FF.FFFF
Peripheral bit-band alias Data accesses to this region are remapped to bit band
region. A write operation is performed as
read-modify-write. Instruction accesses are not permitted.
Start
End
0x4000.0000
0x4200.0000
The following formula shows how the alias region maps onto the bit-band region:
bit_word_offset = (byte_offset x 32) + (bit_number x 4)
bit_word_addr = bit_band_base + bit_word_offset
where:
bit_word_offset
The position of the target bit in the bit-band memory region.
bit_word_addr
The address of the word in the alias memory region that maps to the targeted bit.
bit_band_base
The starting address of the alias region.
byte_offset
The number of the byte in the bit-band region that contains the targeted bit.
bit_number
The bit position, 0-7, of the targeted bit.
Figure 2-4 on page 91 shows examples of bit-band mapping between the SRAM bit-band alias
region and the SRAM bit-band region:
■ The alias word at 0x23FF.FFE0 maps to bit 0 of the bit-band byte at 0x200F.FFFF:
0x23FF.FFE0 = 0x2200.0000 + (0x000F.FFFF*32) + (0*4)
■ The alias word at 0x23FF.FFFC maps to bit 7 of the bit-band byte at 0x200F.FFFF:
0x23FF.FFFC = 0x2200.0000 + (0x000F.FFFF*32) + (7*4)
90
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
■ The alias word at 0x2200.0000 maps to bit 0 of the bit-band byte at 0x2000.0000:
0x2200.0000 = 0x2200.0000 + (0*32) + (0*4)
■ The alias word at 0x2200.001C maps to bit 7 of the bit-band byte at 0x2000.0000:
0x2200.001C = 0x2200.0000+ (0*32) + (7*4)
Figure 2-4. Bit-Band Mapping
32-MB Alias Region
0x23FF.FFFC
0x23FF.FFF8
0x23FF.FFF4
0x23FF.FFF0
0x23FF.FFEC
0x23FF.FFE8
0x23FF.FFE4
0x23FF.FFE0
0x2200.001C
0x2200.0018
0x2200.0014
0x2200.0010
0x2200.000C
0x2200.0008
0x2200.0004
0x2200.0000
7
3
1-MB SRAM Bit-Band Region
7
6
5
4
3
2
1
0
7
6
0x200F.FFFF
7
6
5
4
3
2
0x2000.0003
2.4.5.1
5
4
3
2
1
0
7
6
0x200F.FFFE
1
0
7
6
5
4
3
2
5
4
3
2
1
0
6
0x200F.FFFD
1
0
0x2000.0002
7
6
5
4
3
2
0x2000.0001
5
4
2
1
0
1
0
0x200F.FFFC
1
0
7
6
5
4
3
2
0x2000.0000
Directly Accessing an Alias Region
Writing to a word in the alias region updates a single bit in the bit-band region.
Bit 0 of the value written to a word in the alias region determines the value written to the targeted
bit in the bit-band region. Writing a value with bit 0 set writes a 1 to the bit-band bit, and writing a
value with bit 0 clear writes a 0 to the bit-band bit.
Bits 31:1 of the alias word have no effect on the bit-band bit. Writing 0x01 has the same effect as
writing 0xFF. Writing 0x00 has the same effect as writing 0x0E.
When reading a word in the alias region, 0x0000.0000 indicates that the targeted bit in the bit-band
region is clear and 0x0000.0001 indicates that the targeted bit in the bit-band region is set.
2.4.5.2
Directly Accessing a Bit-Band Region
“Behavior of Memory Accesses” on page 87 describes the behavior of direct byte, halfword, or word
accesses to the bit-band regions.
2.4.6
Data Storage
The processor views memory as a linear collection of bytes numbered in ascending order from zero.
For example, bytes 0-3 hold the first stored word, and bytes 4-7 hold the second stored word. Data
is stored in little-endian format, with the least-significant byte (lsbyte) of a word stored at the
July 17, 2013
91
Texas Instruments-Production Data
The Cortex-M4F Processor
lowest-numbered byte, and the most-significant byte (msbyte) stored at the highest-numbered byte.
Figure 2-5 on page 92 illustrates how data is stored.
Figure 2-5. Data Storage
Memory
7
Register
0
31
2.4.7
Address A
B0
A+1
B1
A+2
B2
A+3
B3
lsbyte
24 23
B3
16 15
B2
8 7
B1
0
B0
msbyte
Synchronization Primitives
The Cortex-M4F instruction set includes pairs of synchronization primitives which provide a
non-blocking mechanism that a thread or process can use to obtain exclusive access to a memory
location. Software can use these primitives to perform a guaranteed read-modify-write memory
update sequence or for a semaphore mechanism.
A pair of synchronization primitives consists of:
■ A Load-Exclusive instruction, which is used to read the value of a memory location and requests
exclusive access to that location.
■ A Store-Exclusive instruction, which is used to attempt to write to the same memory location and
returns a status bit to a register. If this status bit is clear, it indicates that the thread or process
gained exclusive access to the memory and the write succeeds; if this status bit is set, it indicates
that the thread or process did not gain exclusive access to the memory and no write was
performed.
The pairs of Load-Exclusive and Store-Exclusive instructions are:
■ The word instructions LDREX and STREX
■ The halfword instructions LDREXH and STREXH
■ The byte instructions LDREXB and STREXB
Software must use a Load-Exclusive instruction with the corresponding Store-Exclusive instruction.
To perform an exclusive read-modify-write of a memory location, software must:
1. Use a Load-Exclusive instruction to read the value of the location.
2. Modify the value, as required.
3. Use a Store-Exclusive instruction to attempt to write the new value back to the memory location.
4. Test the returned status bit.
92
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
If the status bit is clear, the read-modify-write completed successfully. If the status bit is set, no
write was performed, which indicates that the value returned at step 1 might be out of date. The
software must retry the entire read-modify-write sequence.
Software can use the synchronization primitives to implement a semaphore as follows:
1. Use a Load-Exclusive instruction to read from the semaphore address to check whether the
semaphore is free.
2. If the semaphore is free, use a Store-Exclusive to write the claim value to the semaphore
address.
3. If the returned status bit from step 2 indicates that the Store-Exclusive succeeded, then the
software has claimed the semaphore. However, if the Store-Exclusive failed, another process
might have claimed the semaphore after the software performed step 1.
The Cortex-M4F includes an exclusive access monitor that tags the fact that the processor has
executed a Load-Exclusive instruction. The processor removes its exclusive access tag if:
■ It executes a CLREX instruction.
■ It executes a Store-Exclusive instruction, regardless of whether the write succeeds.
■ An exception occurs, which means the processor can resolve semaphore conflicts between
different threads.
For more information about the synchronization primitive instructions, see the Cortex™-M4 instruction
set chapter in the ARM® Cortex™-M4 Devices Generic User Guide (literature number ARM DUI
0553A).
2.5
Exception Model
The ARM Cortex-M4F processor and the Nested Vectored Interrupt Controller (NVIC) prioritize and
handle all exceptions in Handler Mode. The processor state is automatically stored to the stack on
an exception and automatically restored from the stack at the end of the Interrupt Service Routine
(ISR). The vector is fetched in parallel to the state saving, enabling efficient interrupt entry. The
processor supports tail-chaining, which enables back-to-back interrupts to be performed without the
overhead of state saving and restoration.
Table 2-8 on page 95 lists all exception types. Software can set eight priority levels on seven of
these exceptions (system handlers) as well as on 84 interrupts (listed in Table 2-9 on page 96).
Priorities on the system handlers are set with the NVIC System Handler Priority n (SYSPRIn)
registers. Interrupts are enabled through the NVIC Interrupt Set Enable n (ENn) register and
prioritized with the NVIC Interrupt Priority n (PRIn) registers. Priorities can be grouped by splitting
priority levels into preemption priorities and subpriorities. All the interrupt registers are described in
“Nested Vectored Interrupt Controller (NVIC)” on page 116.
Internally, the highest user-programmable priority (0) is treated as fourth priority, after a Reset,
Non-Maskable Interrupt (NMI), and a Hard Fault, in that order. Note that 0 is the default priority for
all the programmable priorities.
Important: After a write to clear an interrupt source, it may take several processor cycles for the
NVIC to see the interrupt source de-assert. Thus if the interrupt clear is done as the
last action in an interrupt handler, it is possible for the interrupt handler to complete
July 17, 2013
93
Texas Instruments-Production Data
The Cortex-M4F Processor
while the NVIC sees the interrupt as still asserted, causing the interrupt handler to be
re-entered errantly. This situation can be avoided by either clearing the interrupt source
at the beginning of the interrupt handler or by performing a read or write after the write
to clear the interrupt source (and flush the write buffer).
See “Nested Vectored Interrupt Controller (NVIC)” on page 116 for more information on exceptions
and interrupts.
2.5.1
Exception States
Each exception is in one of the following states:
■ Inactive. The exception is not active and not pending.
■ Pending. The exception is waiting to be serviced by the processor. An interrupt request from a
peripheral or from software can change the state of the corresponding interrupt to pending.
■ Active. An exception that is being serviced by the processor but has not completed.
Note:
An exception handler can interrupt the execution of another exception handler. In this
case, both exceptions are in the active state.
■ Active and Pending. The exception is being serviced by the processor, and there is a pending
exception from the same source.
2.5.2
Exception Types
The exception types are:
■ Reset. Reset is invoked on power up or a warm reset. The exception model treats reset as a
special form of exception. When reset is asserted, the operation of the processor stops, potentially
at any point in an instruction. When reset is deasserted, execution restarts from the address
provided by the reset entry in the vector table. Execution restarts as privileged execution in
Thread mode.
■ NMI. A non-maskable Interrupt (NMI) can be signaled using the NMI signal or triggered by
software using the Interrupt Control and State (INTCTRL) register. This exception has the
highest priority other than reset. NMI is permanently enabled and has a fixed priority of -2. NMIs
cannot be masked or prevented from activation by any other exception or preempted by any
exception other than reset.
■ Hard Fault. A hard fault is an exception that occurs because of an error during exception
processing, or because an exception cannot be managed by any other exception mechanism.
Hard faults have a fixed priority of -1, meaning they have higher priority than any exception with
configurable priority.
■ Memory Management Fault. A memory management fault is an exception that occurs because
of a memory protection related fault, including access violation and no match. The MPU or the
fixed memory protection constraints determine this fault, for both instruction and data memory
transactions. This fault is used to abort instruction accesses to Execute Never (XN) memory
regions, even if the MPU is disabled.
■ Bus Fault. A bus fault is an exception that occurs because of a memory-related fault for an
instruction or data memory transaction such as a prefetch fault or a memory access fault. This
fault can be enabled or disabled.
94
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
■ Usage Fault. A usage fault is an exception that occurs because of a fault related to instruction
execution, such as:
– An undefined instruction
– An illegal unaligned access
– Invalid state on instruction execution
– An error on exception return
An unaligned address on a word or halfword memory access or division by zero can cause a
usage fault when the core is properly configured.
■ SVCall. A supervisor call (SVC) is an exception that is triggered by the SVC instruction. In an
OS environment, applications can use SVC instructions to access OS kernel functions and device
drivers.
■ Debug Monitor. This exception is caused by the debug monitor (when not halting). This exception
is only active when enabled. This exception does not activate if it is a lower priority than the
current activation.
■ PendSV. PendSV is a pendable, interrupt-driven request for system-level service. In an OS
environment, use PendSV for context switching when no other exception is active. PendSV is
triggered using the Interrupt Control and State (INTCTRL) register.
■ SysTick. A SysTick exception is an exception that the system timer generates when it reaches
zero when it is enabled to generate an interrupt. Software can also generate a SysTick exception
using the Interrupt Control and State (INTCTRL) register. In an OS environment, the processor
can use this exception as system tick.
■ Interrupt (IRQ). An interrupt, or IRQ, is an exception signaled by a peripheral or generated by
a software request and fed through the NVIC (prioritized). All interrupts are asynchronous to
instruction execution. In the system, peripherals use interrupts to communicate with the processor.
Table 2-9 on page 96 lists the interrupts on the TM4C123BE6PZ controller.
For an asynchronous exception, other than reset, the processor can execute another instruction
between when the exception is triggered and when the processor enters the exception handler.
Privileged software can disable the exceptions that Table 2-8 on page 95 shows as having
configurable priority (see the SYSHNDCTRL register on page 165 and the DIS0 register on page 136).
For more information about hard faults, memory management faults, bus faults, and usage faults,
see “Fault Handling” on page 103.
Table 2-8. Exception Types
Exception Type
a
Vector
Number
Priority
Vector Address or
b
Offset
-
0
-
0x0000.0000
Stack top is loaded from the first
entry of the vector table on reset.
Reset
1
-3 (highest)
0x0000.0004
Asynchronous
Non-Maskable Interrupt
(NMI)
2
-2
0x0000.0008
Asynchronous
Hard Fault
3
-1
0x0000.000C
-
0x0000.0010
Synchronous
Memory Management
4
c
programmable
July 17, 2013
Activation
95
Texas Instruments-Production Data
The Cortex-M4F Processor
Table 2-8. Exception Types (continued)
Exception Type
a
Vector
Number
Priority
Bus Fault
5
programmable
Usage Fault
6
7-10
-
Vector Address or
b
Offset
Activation
c
0x0000.0014
Synchronous when precise and
asynchronous when imprecise
programmable
c
0x0000.0018
Synchronous
-
c
c
Reserved
SVCall
11
programmable
0x0000.002C
Synchronous
Debug Monitor
12
programmable
0x0000.0030
Synchronous
-
13
-
0x0000.0038
Asynchronous
c
0x0000.003C
Asynchronous
PendSV
14
programmable
SysTick
15
programmable
Interrupts
16 and above
Reserved
c
d
programmable
0x0000.0040 and above Asynchronous
a. 0 is the default priority for all the programmable priorities.
b. See “Vector Table” on page 99.
c. See SYSPRI1 on page 162.
d. See PRIn registers on page 144.
Table 2-9. Interrupts
Vector Number
Interrupt Number (Bit
in Interrupt Registers)
Vector Address or
Offset
Description
0-15
-
0x0000.0000 0x0000.003C
16
0
0x0000.0040
GPIO Port A
17
1
0x0000.0044
GPIO Port B
18
2
0x0000.0048
GPIO Port C
19
3
0x0000.004C
GPIO Port D
20
4
0x0000.0050
GPIO Port E
21
5
0x0000.0054
UART0
22
6
0x0000.0058
UART1
23
7
0x0000.005C
SSI0
24
8
0x0000.0060
I2C0
25
9
0x0000.0064
PWM0 Fault
26
10
0x0000.0068
PWM0 Generator 0
27
11
0x0000.006C
PWM0 Generator 1
28
12
0x0000.0070
PWM0 Generator 2
29
13
0x0000.0074
QEI0
30
14
0x0000.0078
ADC0 Sequence 0
31
15
0x0000.007C
ADC0 Sequence 1
32
16
0x0000.0080
ADC0 Sequence 2
33
17
0x0000.0084
ADC0 Sequence 3
34
18
0x0000.0088
Watchdog Timers 0 and 1
35
19
0x0000.008C
16/32-Bit Timer 0A
36
20
0x0000.0090
16/32-Bit Timer 0B
37
21
0x0000.0094
16/32-Bit Timer 1A
Processor exceptions
96
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Table 2-9. Interrupts (continued)
Vector Number
Interrupt Number (Bit
in Interrupt Registers)
Vector Address or
Offset
Description
38
22
0x0000.0098
16/32-Bit Timer 1B
39
23
0x0000.009C
16/32-Bit Timer 2A
40
24
0x0000.00A0
16/32-Bit Timer 2B
41
25
0x0000.00A4
Analog Comparator 0
42
26
0x0000.00A8
Analog Comparator 1
43
27
0x0000.00AC
Analog Comparator 2
44
28
0x0000.00B0
System Control
45
29
0x0000.00B4
Flash Memory Control and EEPROM Control
46
30
0x0000.00B8
GPIO Port F
47
31
0x0000.00BC
GPIO Port G
48
32
0x0000.00C0
GPIO Port H
49
33
0x0000.00C4
UART2
50
34
0x0000.00C8
SSI1
51
35
0x0000.00CC
16/32-Bit Timer 3A
52
36
0x0000.00D0
16/32-Bit Timer 3B
53
37
0x0000.00D4
I2C1
54
38
0x0000.00D8
QEI1
55
39
0x0000.00DC
CAN0
56
40
0x0000.00E0
CAN1
57-58
41-42
-
59
43
0x0000.00EC
60
44
-
61
45
0x0000.00F4
PWM Generator 3
62
46
0x0000.00F8
µDMA Software
63
47
0x0000.00FC
µDMA Error
64
48
0x0000.0100
ADC1 Sequence 0
65
49
0x0000.0104
ADC1 Sequence 1
66
50
0x0000.0108
ADC1 Sequence 2
67
51
0x0000.010C
ADC1 Sequence 3
68-69
52-53
-
70
54
0x0000.0118
GPIO Port J
71
55
0x0000.011C
GPIO Port K
72
56
-
73
57
0x0000.0124
SSI2
74
58
0x0000.0128
SSI3
75
59
0x0000.012C
UART3
76
60
0x0000.0130
UART4
77
61
0x0000.0134
UART5
78
62
0x0000.0138
UART6
79
63
0x0000.013C
UART7
Reserved
Hibernation Module
Reserved
Reserved
Reserved
July 17, 2013
97
Texas Instruments-Production Data
The Cortex-M4F Processor
Table 2-9. Interrupts (continued)
2.5.3
Vector Number
Interrupt Number (Bit
in Interrupt Registers)
Vector Address or
Offset
Description
80-83
64-67
0x0000.0140 0x0000.014C
84
68
0x0000.0150
I2C2
85
69
0x0000.0154
I2C3
86
70
0x0000.0158
16/32-Bit Timer 4A
87
71
0x0000.015C
16/32-Bit Timer 4B
88-107
72-91
0x0000.0160 0x0000.01AC
Reserved
108
92
0x0000.01B0
16/32-Bit Timer 5A
109
93
0x0000.01B4
16/32-Bit Timer 5B
110
94
0x0000.01B8
32/64-Bit Timer 0A
111
95
0x0000.01BC
32/64-Bit Timer 0B
112
96
0x0000.01C0
32/64-Bit Timer 1A
113
97
0x0000.01C4
32/64-Bit Timer 1B
114
98
0x0000.01C8
32/64-Bit Timer 2A
115
99
0x0000.01CC
32/64-Bit Timer 2B
116
100
0x0000.01D0
32/64-Bit Timer 3A
117
101
0x0000.01D4
32/64-Bit Timer 3B
118
102
0x0000.01D8
32/64-Bit Timer 4A
119
103
0x0000.01DC
32/64-Bit Timer 4B
120
104
0x0000.01E0
32/64-Bit Timer 5A
121
105
0x0000.01E4
32/64-Bit Timer 5B
System Exception (imprecise)
Reserved
122
106
0x0000.01E8
123-124
107-108
-
125
109
0x0000.01F4
I2C4
126
110
0x0000.01F8
I2C5
127-149
111-133
-
150
134
0x0000.0258
PWM1 Generator 0
151
135
0x0000.025C
PWM1 Generator 1
152
136
0x0000.0260
PWM1 Generator 2
153
137
0x0000.0264
PWM1 Generator 3
154
138
0x0000.0268
PWM1 Fault
Reserved
Reserved
Exception Handlers
The processor handles exceptions using:
■ Interrupt Service Routines (ISRs). Interrupts (IRQx) are the exceptions handled by ISRs.
■ Fault Handlers. Hard fault, memory management fault, usage fault, and bus fault are fault
exceptions handled by the fault handlers.
■ System Handlers. NMI, PendSV, SVCall, SysTick, and the fault exceptions are all system
exceptions that are handled by system handlers.
98
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
2.5.4
Vector Table
The vector table contains the reset value of the stack pointer and the start addresses, also called
exception vectors, for all exception handlers. The vector table is constructed using the vector address
or offset shown in Table 2-8 on page 95. Figure 2-6 on page 99 shows the order of the exception
vectors in the vector table. The least-significant bit of each vector must be 1, indicating that the
exception handler is Thumb code
Figure 2-6. Vector Table
Exception number IRQ number
154
138
.
.
.
18
2
17
1
16
0
15
-1
14
-2
13
Offset
0x0268
.
.
.
0x004C
0x0048
0x0044
0x0040
0x003C
0x0038
12
11
Vector
IRQ131
.
.
.
IRQ2
IRQ1
IRQ0
Systick
PendSV
Reserved
Reserved for Debug
-5
10
0x002C
9
SVCall
Reserved
8
7
6
-10
5
-11
4
-12
3
-13
2
-14
1
0x0018
0x0014
0x0010
0x000C
0x0008
0x0004
0x0000
Usage fault
Bus fault
Memory management fault
Hard fault
NMI
Reset
Initial SP value
On system reset, the vector table is fixed at address 0x0000.0000. Privileged software can write to
the Vector Table Offset (VTABLE) register to relocate the vector table start address to a different
memory location, in the range 0x0000.0400 to 0x3FFF.FC00 (see “Vector Table” on page 99). Note
that when configuring the VTABLE register, the offset must be aligned on a 1024-byte boundary.
2.5.5
Exception Priorities
As Table 2-8 on page 95 shows, all exceptions have an associated priority, with a lower priority
value indicating a higher priority and configurable priorities for all exceptions except Reset, Hard
fault, and NMI. If software does not configure any priorities, then all exceptions with a configurable
priority have a priority of 0. For information about configuring exception priorities, see page 162 and
page 144.
July 17, 2013
99
Texas Instruments-Production Data
The Cortex-M4F Processor
Note:
Configurable priority values for the Tiva™ C Series implementation are in the range 0-7.
This means that the Reset, Hard fault, and NMI exceptions, with fixed negative priority
values, always have higher priority than any other exception.
For example, assigning a higher priority value to IRQ[0] and a lower priority value to IRQ[1] means
that IRQ[1] has higher priority than IRQ[0]. If both IRQ[1] and IRQ[0] are asserted, IRQ[1] is processed
before IRQ[0].
If multiple pending exceptions have the same priority, the pending exception with the lowest exception
number takes precedence. For example, if both IRQ[0] and IRQ[1] are pending and have the same
priority, then IRQ[0] is processed before IRQ[1].
When the processor is executing an exception handler, the exception handler is preempted if a
higher priority exception occurs. If an exception occurs with the same priority as the exception being
handled, the handler is not preempted, irrespective of the exception number. However, the status
of the new interrupt changes to pending.
2.5.6
Interrupt Priority Grouping
To increase priority control in systems with interrupts, the NVIC supports priority grouping. This
grouping divides each interrupt priority register entry into two fields:
■ An upper field that defines the group priority
■ A lower field that defines a subpriority within the group
Only the group priority determines preemption of interrupt exceptions. When the processor is
executing an interrupt exception handler, another interrupt with the same group priority as the
interrupt being handled does not preempt the handler.
If multiple pending interrupts have the same group priority, the subpriority field determines the order
in which they are processed. If multiple pending interrupts have the same group priority and
subpriority, the interrupt with the lowest IRQ number is processed first.
For information about splitting the interrupt priority fields into group priority and subpriority, see
page 156.
2.5.7
Exception Entry and Return
Descriptions of exception handling use the following terms:
■ Preemption. When the processor is executing an exception handler, an exception can preempt
the exception handler if its priority is higher than the priority of the exception being handled. See
“Interrupt Priority Grouping” on page 100 for more information about preemption by an interrupt.
When one exception preempts another, the exceptions are called nested exceptions. See
“Exception Entry” on page 101 more information.
■ Return. Return occurs when the exception handler is completed, and there is no pending
exception with sufficient priority to be serviced and the completed exception handler was not
handling a late-arriving exception. The processor pops the stack and restores the processor
state to the state it had before the interrupt occurred. See “Exception Return” on page 102 for
more information.
■ Tail-Chaining. This mechanism speeds up exception servicing. On completion of an exception
handler, if there is a pending exception that meets the requirements for exception entry, the
stack pop is skipped and control transfers to the new exception handler.
100
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
■ Late-Arriving. This mechanism speeds up preemption. If a higher priority exception occurs
during state saving for a previous exception, the processor switches to handle the higher priority
exception and initiates the vector fetch for that exception. State saving is not affected by late
arrival because the state saved is the same for both exceptions. Therefore, the state saving
continues uninterrupted. The processor can accept a late arriving exception until the first instruction
of the exception handler of the original exception enters the execute stage of the processor. On
return from the exception handler of the late-arriving exception, the normal tail-chaining rules
apply.
2.5.7.1
Exception Entry
Exception entry occurs when there is a pending exception with sufficient priority and either the
processor is in Thread mode or the new exception is of higher priority than the exception being
handled, in which case the new exception preempts the original exception.
When one exception preempts another, the exceptions are nested.
Sufficient priority means the exception has more priority than any limits set by the mask registers
(see PRIMASK on page 77, FAULTMASK on page 78, and BASEPRI on page 79). An exception
with less priority than this is pending but is not handled by the processor.
When the processor takes an exception, unless the exception is a tail-chained or a late-arriving
exception, the processor pushes information onto the current stack. This operation is referred to as
stacking and the structure of eight data words is referred to as stack frame.
When using floating-point routines, the Cortex-M4F processor automatically stacks the architected
floating-point state on exception entry. Figure 2-7 on page 102 shows the Cortex-M4F stack frame
layout when floating-point state is preserved on the stack as the result of an interrupt or an exception.
Note:
Where stack space for floating-point state is not allocated, the stack frame is the same as
that of ARMv7-M implementations without an FPU. Figure 2-7 on page 102 shows this stack
frame also.
July 17, 2013
101
Texas Instruments-Production Data
The Cortex-M4F Processor
Figure 2-7. Exception Stack Frame
...
{aligner}
FPSCR
S15
S14
S13
S12
S11
S10
S9
S8
S7
S6
S5
S4
S3
S2
S1
S0
xPSR
PC
LR
R12
R3
R2
R1
R0
Exception frame with
floating-point storage
Pre-IRQ top of stack
Decreasing
memory
address
IRQ top of stack
...
{aligner}
xPSR
PC
LR
R12
R3
R2
R1
R0
Pre-IRQ top of stack
IRQ top of stack
Exception frame without
floating-point storage
Immediately after stacking, the stack pointer indicates the lowest address in the stack frame.
The stack frame includes the return address, which is the address of the next instruction in the
interrupted program. This value is restored to the PC at exception return so that the interrupted
program resumes.
In parallel with the stacking operation, the processor performs a vector fetch that reads the exception
handler start address from the vector table. When stacking is complete, the processor starts executing
the exception handler. At the same time, the processor writes an EXC_RETURN value to the LR,
indicating which stack pointer corresponds to the stack frame and what operation mode the processor
was in before the entry occurred.
If no higher-priority exception occurs during exception entry, the processor starts executing the
exception handler and automatically changes the status of the corresponding pending interrupt to
active.
If another higher-priority exception occurs during exception entry, known as late arrival, the processor
starts executing the exception handler for this exception and does not change the pending status
of the earlier exception.
2.5.7.2
Exception Return
Exception return occurs when the processor is in Handler mode and executes one of the following
instructions to load the EXC_RETURN value into the PC:
102
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
■ An LDM or POP instruction that loads the PC
■ A BX instruction using any register
■ An LDR instruction with the PC as the destination
EXC_RETURN is the value loaded into the LR on exception entry. The exception mechanism relies
on this value to detect when the processor has completed an exception handler. The lowest five
bits of this value provide information on the return stack and processor mode. Table 2-10 on page 103
shows the EXC_RETURN values with a description of the exception return behavior.
EXC_RETURN bits 31:5 are all set. When this value is loaded into the PC, it indicates to the processor
that the exception is complete, and the processor initiates the appropriate exception return sequence.
Table 2-10. Exception Return Behavior
EXC_RETURN[31:0]
Description
0xFFFF.FFE0
Reserved
0xFFFF.FFE1
Return to Handler mode.
Exception return uses floating-point state from MSP.
Execution uses MSP after return.
0xFFFF.FFE2 - 0xFFFF.FFE8
Reserved
0xFFFF.FFE9
Return to Thread mode.
Exception return uses floating-point state from MSP.
Execution uses MSP after return.
0xFFFF.FFEA - 0xFFFF.FFEC
Reserved
0xFFFF.FFED
Return to Thread mode.
Exception return uses floating-point state from PSP.
Execution uses PSP after return.
0xFFFF.FFEE - 0xFFFF.FFF0
Reserved
0xFFFF.FFF1
Return to Handler mode.
Exception return uses non-floating-point state from MSP.
Execution uses MSP after return.
0xFFFF.FFF2 - 0xFFFF.FFF8
Reserved
0xFFFF.FFF9
Return to Thread mode.
Exception return uses non-floating-point state from MSP.
Execution uses MSP after return.
0xFFFF.FFFA - 0xFFFF.FFFC
Reserved
0xFFFF.FFFD
Return to Thread mode.
Exception return uses non-floating-point state from PSP.
Execution uses PSP after return.
0xFFFF.FFFE - 0xFFFF.FFFF
2.6
Reserved
Fault Handling
Faults are a subset of the exceptions (see “Exception Model” on page 93). The following conditions
generate a fault:
■ A bus error on an instruction fetch or vector table load or a data access.
July 17, 2013
103
Texas Instruments-Production Data
The Cortex-M4F Processor
■ An internally detected error such as an undefined instruction or an attempt to change state with
a BX instruction.
■ Attempting to execute an instruction from a memory region marked as Non-Executable (XN).
■ An MPU fault because of a privilege violation or an attempt to access an unmanaged region.
2.6.1
Fault Types
Table 2-11 on page 104 shows the types of fault, the handler used for the fault, the corresponding
fault status register, and the register bit that indicates the fault has occurred. See page 169 for more
information about the fault status registers.
Table 2-11. Faults
Fault
Handler
Fault Status Register
Bit Name
Bus error on a vector read
Hard fault
Hard Fault Status (HFAULTSTAT)
VECT
Fault escalated to a hard fault
Hard fault
Hard Fault Status (HFAULTSTAT)
FORCED
MPU or default memory mismatch on
instruction access
Memory management
fault
Memory Management Fault Status
(MFAULTSTAT)
IERR
MPU or default memory mismatch on
data access
Memory management
fault
Memory Management Fault Status
(MFAULTSTAT)
DERR
MPU or default memory mismatch on
exception stacking
Memory management
fault
Memory Management Fault Status
(MFAULTSTAT)
MSTKE
MPU or default memory mismatch on
exception unstacking
Memory management
fault
Memory Management Fault Status
(MFAULTSTAT)
MUSTKE
MPU or default memory mismatch
during lazy floating-point state
preservation
Memory management
fault
Memory Management Fault Status
(MFAULTSTAT)
MLSPERR
Bus error during exception stacking
Bus fault
Bus Fault Status (BFAULTSTAT)
BSTKE
Bus error during exception unstacking Bus fault
Bus Fault Status (BFAULTSTAT)
BUSTKE
Bus error during instruction prefetch
Bus fault
Bus Fault Status (BFAULTSTAT)
IBUS
Bus error during lazy floating-point state Bus fault
preservation
Bus Fault Status (BFAULTSTAT)
BLSPE
Precise data bus error
Bus fault
Bus Fault Status (BFAULTSTAT)
PRECISE
Imprecise data bus error
Bus fault
Bus Fault Status (BFAULTSTAT)
IMPRE
Attempt to access a coprocessor
Usage fault
Usage Fault Status (UFAULTSTAT)
NOCP
Undefined instruction
Usage fault
Usage Fault Status (UFAULTSTAT)
UNDEF
Attempt to enter an invalid instruction
b
set state
Usage fault
Usage Fault Status (UFAULTSTAT)
INVSTAT
Invalid EXC_RETURN value
Usage fault
Usage Fault Status (UFAULTSTAT)
INVPC
Illegal unaligned load or store
Usage fault
Usage Fault Status (UFAULTSTAT)
UNALIGN
Divide by 0
Usage fault
Usage Fault Status (UFAULTSTAT)
DIV0
a
a. Occurs on an access to an XN region even if the MPU is disabled.
b. Attempting to use an instruction set other than the Thumb instruction set, or returning to a non load-store-multiple instruction
with ICI continuation.
2.6.2
Fault Escalation and Hard Faults
All fault exceptions except for hard fault have configurable exception priority (see SYSPRI1 on
page 162). Software can disable execution of the handlers for these faults (see SYSHNDCTRL on
page 165).
104
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Usually, the exception priority, together with the values of the exception mask registers, determines
whether the processor enters the fault handler, and whether a fault handler can preempt another
fault handler as described in “Exception Model” on page 93.
In some situations, a fault with configurable priority is treated as a hard fault. This process is called
priority escalation, and the fault is described as escalated to hard fault. Escalation to hard fault
occurs when:
■ A fault handler causes the same kind of fault as the one it is servicing. This escalation to hard
fault occurs because a fault handler cannot preempt itself because it must have the same priority
as the current priority level.
■ A fault handler causes a fault with the same or lower priority as the fault it is servicing. This
situation happens because the handler for the new fault cannot preempt the currently executing
fault handler.
■ An exception handler causes a fault for which the priority is the same as or lower than the currently
executing exception.
■ A fault occurs and the handler for that fault is not enabled.
If a bus fault occurs during a stack push when entering a bus fault handler, the bus fault does not
escalate to a hard fault. Thus if a corrupted stack causes a fault, the fault handler executes even
though the stack push for the handler failed. The fault handler operates but the stack contents are
corrupted.
Note:
2.6.3
Only Reset and NMI can preempt the fixed priority hard fault. A hard fault can preempt any
exception other than Reset, NMI, or another hard fault.
Fault Status Registers and Fault Address Registers
The fault status registers indicate the cause of a fault. For bus faults and memory management
faults, the fault address register indicates the address accessed by the operation that caused the
fault, as shown in Table 2-12 on page 105.
Table 2-12. Fault Status and Fault Address Registers
Handler
Status Register Name
Address Register Name
Register Description
Hard fault
Hard Fault Status (HFAULTSTAT)
-
page 175
Memory management Memory Management Fault Status
fault
(MFAULTSTAT)
Memory Management Fault
Address (MMADDR)
page 169
Bus fault
Bus Fault Address
(FAULTADDR)
page 169
-
page 169
Bus Fault Status (BFAULTSTAT)
Usage fault
2.6.4
Usage Fault Status (UFAULTSTAT)
page 176
page 177
Lockup
The processor enters a lockup state if a hard fault occurs when executing the NMI or hard fault
handlers. When the processor is in the lockup state, it does not execute any instructions. The
processor remains in lockup state until it is reset, an NMI occurs, or it is halted by a debugger.
Note:
If the lockup state occurs from the NMI handler, a subsequent NMI does not cause the
processor to leave the lockup state.
July 17, 2013
105
Texas Instruments-Production Data
The Cortex-M4F Processor
2.7
Power Management
The Cortex-M4F processor sleep modes reduce power consumption:
■ Sleep mode stops the processor clock.
■ Deep-sleep mode stops the system clock and switches off the PLL and Flash memory.
The SLEEPDEEP bit of the System Control (SYSCTRL) register selects which sleep mode is used
(see page 158). For more information about the behavior of the sleep modes, see “System
Control” on page 218.
This section describes the mechanisms for entering sleep mode and the conditions for waking up
from sleep mode, both of which apply to Sleep mode and Deep-sleep mode.
2.7.1
Entering Sleep Modes
This section describes the mechanisms software can use to put the processor into one of the sleep
modes.
The system can generate spurious wake-up events, for example a debug operation wakes up the
processor. Therefore, software must be able to put the processor back into sleep mode after such
an event. A program might have an idle loop to put the processor back to sleep mode.
2.7.1.1
Wait for Interrupt
The wait for interrupt instruction, WFI, causes immediate entry to sleep mode unless the wake-up
condition is true (see “Wake Up from WFI or Sleep-on-Exit” on page 107). When the processor
executes a WFI instruction, it stops executing instructions and enters sleep mode. See the
Cortex™-M4 instruction set chapter in the ARM® Cortex™-M4 Devices Generic User Guide (literature
number ARM DUI 0553A) for more information.
2.7.1.2
Wait for Event
The wait for event instruction, WFE, causes entry to sleep mode conditional on the value of a one-bit
event register. When the processor executes a WFE instruction, it checks the event register. If the
register is 0, the processor stops executing instructions and enters sleep mode. If the register is 1,
the processor clears the register and continues executing instructions without entering sleep mode.
If the event register is 1, the processor must not enter sleep mode on execution of a WFE instruction.
Typically, this situation occurs if an SEV instruction has been executed. Software cannot access
this register directly.
See the Cortex™-M4 instruction set chapter in the ARM® Cortex™-M4 Devices Generic User Guide
(literature number ARM DUI 0553A) for more information.
2.7.1.3
Sleep-on-Exit
If the SLEEPEXIT bit of the SYSCTRL register is set, when the processor completes the execution
of all exception handlers, it returns to Thread mode and immediately enters sleep mode. This
mechanism can be used in applications that only require the processor to run when an exception
occurs.
2.7.2
Wake Up from Sleep Mode
The conditions for the processor to wake up depend on the mechanism that caused it to enter sleep
mode.
106
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
2.7.2.1
Wake Up from WFI or Sleep-on-Exit
Normally, the processor wakes up only when the NVIC detects an exception with sufficient priority
to cause exception entry. Some embedded systems might have to execute system restore tasks
after the processor wakes up and before executing an interrupt handler. Entry to the interrupt handler
can be delayed by setting the PRIMASK bit and clearing the FAULTMASK bit. If an interrupt arrives
that is enabled and has a higher priority than current exception priority, the processor wakes up but
does not execute the interrupt handler until the processor clears PRIMASK. For more information
about PRIMASK and FAULTMASK, see page 77 and page 78.
2.7.2.2
Wake Up from WFE
The processor wakes up if it detects an exception with sufficient priority to cause exception entry.
In addition, if the SEVONPEND bit in the SYSCTRL register is set, any new pending interrupt triggers
an event and wakes up the processor, even if the interrupt is disabled or has insufficient priority to
cause exception entry. For more information about SYSCTRL, see page 158.
2.8
Instruction Set Summary
The processor implements a version of the Thumb instruction set. Table 2-13 on page 107 lists the
supported instructions.
Note:
In Table 2-13 on page 107:
■
■
■
■
■
Angle brackets, <>, enclose alternative forms of the operand
Braces, {}, enclose optional operands
The Operands column is not exhaustive
Op2 is a flexible second operand that can be either a register or a constant
Most instructions can use an optional condition code suffix
For more information on the instructions and operands, see the instruction descriptions in
the ARM® Cortex™-M4 Technical Reference Manual.
Table 2-13. Cortex-M4F Instruction Summary
Mnemonic
Operands
Brief Description
Flags
ADC, ADCS
{Rd,} Rn, Op2
Add with carry
N,Z,C,V
ADD, ADDS
{Rd,} Rn, Op2
Add
N,Z,C,V
ADD, ADDW
{Rd,} Rn , #imm12
Add
-
ADR
Rd, label
Load PC-relative address
-
AND, ANDS
{Rd,} Rn, Op2
Logical AND
N,Z,C
ASR, ASRS
Rd, Rm, <Rs|#n>
Arithmetic shift right
N,Z,C
B
label
Branch
-
BFC
Rd, #lsb, #width
Bit field clear
-
BFI
Rd, Rn, #lsb, #width
Bit field insert
-
BIC, BICS
{Rd,} Rn, Op2
Bit clear
N,Z,C
BKPT
#imm
Breakpoint
-
BL
label
Branch with link
-
BLX
Rm
Branch indirect with link
-
BX
Rm
Branch indirect
-
CBNZ
Rn, label
Compare and branch if non-zero
-
July 17, 2013
107
Texas Instruments-Production Data
The Cortex-M4F Processor
Table 2-13. Cortex-M4F Instruction Summary (continued)
Mnemonic
Operands
Brief Description
Flags
CBZ
Rn, label
Compare and branch if zero
-
CLREX
-
Clear exclusive
-
CLZ
Rd, Rm
Count leading zeros
-
CMN
Rn, Op2
Compare negative
N,Z,C,V
CMP
Rn, Op2
Compare
N,Z,C,V
CPSID
i
Change processor state, disable
interrupts
-
CPSIE
i
Change processor state, enable
interrupts
-
DMB
-
Data memory barrier
-
DSB
-
Data synchronization barrier
-
EOR, EORS
{Rd,} Rn, Op2
Exclusive OR
N,Z,C
ISB
-
Instruction synchronization barrier
-
IT
-
If-Then condition block
-
LDM
Rn{!}, reglist
Load multiple registers, increment after -
LDMDB, LDMEA
Rn{!}, reglist
Load multiple registers, decrement
before
LDMFD, LDMIA
Rn{!}, reglist
Load multiple registers, increment after -
LDR
Rt, [Rn, #offset]
Load register with word
-
LDRB, LDRBT
Rt, [Rn, #offset]
Load register with byte
-
LDRD
Rt, Rt2, [Rn, #offset]
Load register with two bytes
-
LDREX
Rt, [Rn, #offset]
Load register exclusive
-
LDREXB
Rt, [Rn]
Load register exclusive with byte
-
LDREXH
Rt, [Rn]
Load register exclusive with halfword
-
LDRH, LDRHT
Rt, [Rn, #offset]
Load register with halfword
-
LDRSB, LDRSBT
Rt, [Rn, #offset]
Load register with signed byte
-
LDRSH, LDRSHT
Rt, [Rn, #offset]
Load register with signed halfword
-
LDRT
Rt, [Rn, #offset]
Load register with word
-
LSL, LSLS
Rd, Rm, <Rs|#n>
Logical shift left
N,Z,C
LSR, LSRS
Rd, Rm, <Rs|#n>
Logical shift right
N,Z,C
MLA
Rd, Rn, Rm, Ra
Multiply with accumulate, 32-bit result
-
MLS
Rd, Rn, Rm, Ra
Multiply and subtract, 32-bit result
-
MOV, MOVS
Rd, Op2
Move
N,Z,C
MOV, MOVW
Rd, #imm16
Move 16-bit constant
N,Z,C
MOVT
Rd, #imm16
Move top
-
MRS
Rd, spec_reg
Move from special register to general
register
-
MSR
spec_reg, Rm
Move from general register to special
register
N,Z,C,V
MUL, MULS
{Rd,} Rn, Rm
Multiply, 32-bit result
N,Z
MVN, MVNS
Rd, Op2
Move NOT
N,Z,C
NOP
-
No operation
-
ORN, ORNS
{Rd,} Rn, Op2
Logical OR NOT
N,Z,C
108
-
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Table 2-13. Cortex-M4F Instruction Summary (continued)
Mnemonic
Operands
Brief Description
Flags
ORR, ORRS
{Rd,} Rn, Op2
Logical OR
N,Z,C
PKHTB, PKHBT
{Rd,} Rn, Rm, Op2
Pack halfword
-
POP
reglist
Pop registers from stack
-
PUSH
reglist
Push registers onto stack
-
QADD
{Rd,} Rn, Rm
Saturating add
Q
QADD16
{Rd,} Rn, Rm
Saturating add 16
-
QADD8
{Rd,} Rn, Rm
Saturating add 8
-
QASX
{Rd,} Rn, Rm
Saturating add and subtract with
exchange
-
QDADD
{Rd,} Rn, Rm
Saturating double and add
Q
QDSUB
{Rd,} Rn, Rm
Saturating double and subtract
Q
QSAX
{Rd,} Rn, Rm
Saturating subtract and add with
exchange
-
QSUB
{Rd,} Rn, Rm
Saturating subtract
Q
QSUB16
{Rd,} Rn, Rm
Saturating subtract 16
-
QSUB8
{Rd,} Rn, Rm
Saturating subtract 8
-
RBIT
Rd, Rn
Reverse bits
-
REV
Rd, Rn
Reverse byte order in a word
-
REV16
Rd, Rn
Reverse byte order in each halfword
-
REVSH
Rd, Rn
Reverse byte order in bottom halfword
and sign extend
-
ROR, RORS
Rd, Rm, <Rs|#n>
Rotate right
N,Z,C
RRX, RRXS
Rd, Rm
Rotate right with extend
N,Z,C
RSB, RSBS
{Rd,} Rn, Op2
Reverse subtract
N,Z,C,V
SADD16
{Rd,} Rn, Rm
Signed add 16
GE
SADD8
{Rd,} Rn, Rm
Signed add 8
GE
SASX
{Rd,} Rn, Rm
Signed add and subtract with exchange GE
SBC, SBCS
{Rd,} Rn, Op2
Subtract with carry
N,Z,C,V
SBFX
Rd, Rn, #lsb, #width
Signed bit field extract
-
SDIV
{Rd,} Rn, Rm
Signed divide
-
SEL
{Rd,} Rn, Rm
Select bytes
-
SEV
-
Send event
-
SHADD16
{Rd,} Rn, Rm
Signed halving add 16
-
SHADD8
{Rd,} Rn, Rm
Signed halving add 8
-
SHASX
{Rd,} Rn, Rm
Signed halving add and subtract with
exchange
-
SHSAX
{Rd,} Rn, Rm
Signed halving add and subtract with
exchange
-
SHSUB16
{Rd,} Rn, Rm
Signed halving subtract 16
-
SHSUB8
{Rd,} Rn, Rm
Signed halving subtract 8
-
July 17, 2013
109
Texas Instruments-Production Data
The Cortex-M4F Processor
Table 2-13. Cortex-M4F Instruction Summary (continued)
Mnemonic
Operands
Brief Description
Flags
SMLABB,
Rd, Rn, Rm, Ra
Signed multiply accumulate long
(halfwords)
Q
Rd, Rn, Rm, Ra
Signed multiply accumulate dual
Q
SMLAL
RdLo, RdHi, Rn, Rm
Signed multiply with accumulate
(32x32+64), 64-bit result
-
SMLALBB,
RdLo, RdHi, Rn, Rm
Signed multiply accumulate long
(halfwords)
-
SMLALD, SMLALDX
RdLo, RdHi, Rn, Rm
Signed multiply accumulate long dual
-
SMLAWB,SMLAWT
Rd, Rn, Rm, Ra
Signed multiply accumulate, word by
halfword
Q
SMLSD
Rd, Rn, Rm, Ra
Signed multiply subtract dual
Q
RdLo, RdHi, Rn, Rm
Signed multiply subtract long dual
SMMLA
Rd, Rn, Rm, Ra
Signed most significant word multiply
accumulate
-
SMMLS,
Rd, Rn, Rm, Ra
Signed most significant word multiply
subtract
-
{Rd,} Rn, Rm
Signed most significant word multiply
-
{Rd,} Rn, Rm
Signed dual multiply add
Q
{Rd,} Rn, Rm
Signed multiply halfwords
-
SMULL
RdLo, RdHi, Rn, Rm
Signed multiply (32x32), 64-bit result
-
SMULWB,
{Rd,} Rn, Rm
Signed multiply by halfword
-
{Rd,} Rn, Rm
Signed dual multiply subtract
-
SSAT
Rd, #n, Rm {,shift #s}
Signed saturate
Q
SSAT16
Rd, #n, Rm
Signed saturate 16
Q
SSAX
{Rd,} Rn, Rm
Saturating subtract and add with
exchange
GE
SSUB16
{Rd,} Rn, Rm
Signed subtract 16
-
SSUB8
{Rd,} Rn, Rm
Signed subtract 8
-
STM
Rn{!}, reglist
Store multiple registers, increment after -
SMLABT,
SMLATB,
SMLATT
SMLAD,
SMLADX
SMLALBT,
SMLALTB,
SMLALTT
SMLSDX
SMLSLD
SMLSLDX
SMMLR
SMMUL,
SMMULR
SMUAD
SMUADX
SMULBB,
SMULBT,
SMULTB,
SMULTT
SMULWT
SMUSD,
SMUSDX
110
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Table 2-13. Cortex-M4F Instruction Summary (continued)
Mnemonic
Operands
Brief Description
Flags
STMDB, STMEA
Rn{!}, reglist
Store multiple registers, decrement
before
-
STMFD, STMIA
Rn{!}, reglist
Store multiple registers, increment after -
STR
Rt, [Rn {, #offset}]
Store register word
-
STRB, STRBT
Rt, [Rn {, #offset}]
Store register byte
-
STRD
Rt, Rt2, [Rn {, #offset}]
Store register two words
-
STREX
Rt, Rt, [Rn {, #offset}]
Store register exclusive
-
STREXB
Rd, Rt, [Rn]
Store register exclusive byte
-
STREXH
Rd, Rt, [Rn]
Store register exclusive halfword
-
STRH, STRHT
Rt, [Rn {, #offset}]
Store register halfword
-
STRSB, STRSBT
Rt, [Rn {, #offset}]
Store register signed byte
-
STRSH, STRSHT
Rt, [Rn {, #offset}]
Store register signed halfword
-
STRT
Rt, [Rn {, #offset}]
Store register word
-
SUB, SUBS
{Rd,} Rn, Op2
Subtract
N,Z,C,V
SUB, SUBW
{Rd,} Rn, #imm12
Subtract 12-bit constant
N,Z,C,V
SVC
#imm
Supervisor call
-
SXTAB
{Rd,} Rn, Rm, {,ROR #}
Extend 8 bits to 32 and add
-
SXTAB16
{Rd,} Rn, Rm,{,ROR #}
Dual extend 8 bits to 16 and add
-
SXTAH
{Rd,} Rn, Rm,{,ROR #}
Extend 16 bits to 32 and add
-
SXTB16
{Rd,} Rm {,ROR #n}
Signed extend byte 16
-
SXTB
{Rd,} Rm {,ROR #n}
Sign extend a byte
-
SXTH
{Rd,} Rm {,ROR #n}
Sign extend a halfword
-
TBB
[Rn, Rm]
Table branch byte
-
TBH
[Rn, Rm, LSL #1]
Table branch halfword
-
TEQ
Rn, Op2
Test equivalence
N,Z,C
TST
Rn, Op2
Test
N,Z,C
UADD16
{Rd,} Rn, Rm
Unsigned add 16
GE
UADD8
{Rd,} Rn, Rm
Unsigned add 8
GE
UASX
{Rd,} Rn, Rm
Unsigned add and subtract with
exchange
GE
UHADD16
{Rd,} Rn, Rm
Unsigned halving add 16
-
UHADD8
{Rd,} Rn, Rm
Unsigned halving add 8
-
UHASX
{Rd,} Rn, Rm
Unsigned halving add and subtract with exchange
UHSAX
{Rd,} Rn, Rm
Unsigned halving subtract and add with exchange
UHSUB16
{Rd,} Rn, Rm
Unsigned halving subtract 16
-
UHSUB8
{Rd,} Rn, Rm
Unsigned halving subtract 8
-
UBFX
Rd, Rn, #lsb, #width
Unsigned bit field extract
-
UDIV
{Rd,} Rn, Rm
Unsigned divide
-
UMAAL
RdLo, RdHi, Rn, Rm
Unsigned multiply accumulate
accumulate long (32x32+64), 64-bit
result
-
July 17, 2013
111
Texas Instruments-Production Data
The Cortex-M4F Processor
Table 2-13. Cortex-M4F Instruction Summary (continued)
Mnemonic
Operands
Brief Description
Flags
UMLAL
RdLo, RdHi, Rn, Rm
Unsigned multiply with accumulate
(32x32+32+32), 64-bit result
-
UMULL
RdLo, RdHi, Rn, Rm
Unsigned multiply (32x 2), 64-bit result -
UQADD16
{Rd,} Rn, Rm
Unsigned Saturating Add 16
-
UQADD8
{Rd,} Rn, Rm
Unsigned Saturating Add 8
-
UQASX
{Rd,} Rn, Rm
Unsigned Saturating Add and Subtract with Exchange
UQSAX
{Rd,} Rn, Rm
Unsigned Saturating Subtract and Add with Exchange
UQSUB16
{Rd,} Rn, Rm
Unsigned Saturating Subtract 16
-
UQSUB8
{Rd,} Rn, Rm
Unsigned Saturating Subtract 8
-
USAD8
{Rd,} Rn, Rm
Unsigned Sum of Absolute Differences -
USADA8
{Rd,} Rn, Rm, Ra
Unsigned Sum of Absolute Differences and Accumulate
USAT
Rd, #n, Rm {,shift #s}
Unsigned Saturate
Q
USAT16
Rd, #n, Rm
Unsigned Saturate 16
Q
USAX
{Rd,} Rn, Rm
Unsigned Subtract and add with
Exchange
GE
USUB16
{Rd,} Rn, Rm
Unsigned Subtract 16
GE
USUB8
{Rd,} Rn, Rm
Unsigned Subtract 8
GE
UXTAB
{Rd,} Rn, Rm, {,ROR #}
Rotate, extend 8 bits to 32 and Add
-
UXTAB16
{Rd,} Rn, Rm, {,ROR #}
Rotate, dual extend 8 bits to 16 and Add -
UXTAH
{Rd,} Rn, Rm, {,ROR #}
Rotate, unsigned extend and Add
Halfword
-
UXTB
{Rd,} Rm, {,ROR #n}
Zero extend a Byte
-
UXTB16
{Rd,} Rm, {,ROR #n}
Unsigned Extend Byte 16
-
UXTH
{Rd,} Rm, {,ROR #n}
Zero extend a Halfword
-
VABS.F32
Sd, Sm
Floating-point Absolute
-
VADD.F32
{Sd,} Sn, Sm
Floating-point Add
-
VCMP.F32
Sd, <Sm | #0.0>
Compare two floating-point registers, or FPSCR
one floating-point register and zero
VCMPE.F32
Sd, <Sm | #0.0>
Compare two floating-point registers, or FPSCR
one floating-point register and zero with
Invalid Operation check
VCVT.S32.F32
Sd, Sm
Convert between floating-point and
integer
VCVT.S16.F32
Sd, Sd, #fbits
Convert between floating-point and fixed point
VCVTR.S32.F32
Sd, Sm
Convert between floating-point and
integer with rounding
-
VCVT<B|H>.F32.F16
Sd, Sm
Converts half-precision value to
single-precision
-
VCVTT<B|T>.F32.F16
Sd, Sm
Converts single-precision register to
half-precision
-
VDIV.F32
{Sd,} Sn, Sm
Floating-point Divide
-
VFMA.F32
{Sd,} Sn, Sm
Floating-point Fused Multiply Accumulate -
112
-
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Table 2-13. Cortex-M4F Instruction Summary (continued)
Mnemonic
Operands
Brief Description
Flags
VFNMA.F32
{Sd,} Sn, Sm
Floating-point Fused Negate Multiply
Accumulate
-
VFMS.F32
{Sd,} Sn, Sm
Floating-point Fused Multiply Subtract
-
VFNMS.F32
{Sd,} Sn, Sm
Floating-point Fused Negate Multiply
Subtract
-
VLDM.F<32|64>
Rn{!}, list
Load Multiple extension registers
-
VLDR.F<32|64>
<Dd|Sd>, [Rn]
Load an extension register from memory -
VLMA.F32
{Sd,} Sn, Sm
Floating-point Multiply Accumulate
-
VLMS.F32
{Sd,} Sn, Sm
Floating-point Multiply Subtract
-
VMOV.F32
Sd, #imm
Floating-point Move immediate
-
VMOV
Sd, Sm
Floating-point Move register
-
VMOV
Sn, Rt
Copy ARM core register to single
precision
-
VMOV
Sm, Sm1, Rt, Rt2
Copy 2 ARM core registers to 2 single
precision
-
VMOV
Dd[x], Rt
Copy ARM core register to scalar
-
VMOV
Rt, Dn[x]
Copy scalar to ARM core register
-
VMRS
Rt, FPSCR
Move FPSCR to ARM core register or
APSR
N,Z,C,V
VMSR
FPSCR, Rt
Move to FPSCR from ARM Core register FPSCR
VMUL.F32
{Sd,} Sn, Sm
Floating-point Multiply
-
VNEG.F32
Sd, Sm
Floating-point Negate
-
VNMLA.F32
{Sd,} Sn, Sm
Floating-point Multiply and Add
-
VNMLS.F32
{Sd,} Sn, Sm
Floating-point Multiply and Subtract
-
VNMUL
{Sd,} Sn, Sm
Floating-point Multiply
-
VPOP
list
Pop extension registers
-
VPUSH
list
Push extension registers
-
VSQRT.F32
Sd, Sm
Calculates floating-point Square Root
-
VSTM
Rn{!}, list
Floating-point register Store Multiple
-
VSTR.F3<32|64>
Sd, [Rn]
Stores an extension register to memory -
VSUB.F<32|64>
{Sd,} Sn, Sm
Floating-point Subtract
-
WFE
-
Wait for event
-
WFI
-
Wait for interrupt
-
July 17, 2013
113
Texas Instruments-Production Data
Cortex-M4 Peripherals
3
Cortex-M4 Peripherals
This chapter provides information on the Tiva™ C Series implementation of the Cortex-M4 processor
peripherals, including:
■ SysTick (see page 115)
Provides a simple, 24-bit clear-on-write, decrementing, wrap-on-zero counter with a flexible
control mechanism.
■ Nested Vectored Interrupt Controller (NVIC) (see page 116)
– Facilitates low-latency exception and interrupt handling
– Controls power management
– Implements system control registers
■ System Control Block (SCB) (see page 117)
Provides system implementation information and system control, including configuration, control,
and reporting of system exceptions.
■ Memory Protection Unit (MPU) (see page 117)
Supports the standard ARMv7 Protected Memory System Architecture (PMSA) model. The MPU
provides full support for protection regions, overlapping protection regions, access permissions,
and exporting memory attributes to the system.
■ Floating-Point Unit (FPU) (see page 122)
Fully supports single-precision add, subtract, multiply, divide, multiply and accumulate, and
square root operations. It also provides conversions between fixed-point and floating-point data
formats, and floating-point constant instructions.
Table 3-1 on page 114 shows the address map of the Private Peripheral Bus (PPB). Some peripheral
register regions are split into two address regions, as indicated by two addresses listed.
Table 3-1. Core Peripheral Register Regions
Address
Core Peripheral
Description (see page ...)
0xE000.E010-0xE000.E01F
System Timer
115
0xE000.E100-0xE000.E4EF
Nested Vectored Interrupt Controller
116
System Control Block
117
0xE000.ED90-0xE000.EDB8
Memory Protection Unit
117
0xE000.EF30-0xE000.EF44
Floating Point Unit
122
0xE000.EF00-0xE000.EF03
0xE000.E008-0xE000.E00F
0xE000.ED00-0xE000.ED3F
3.1
Functional Description
This chapter provides information on the Tiva™ C Series implementation of the Cortex-M4 processor
peripherals: SysTick, NVIC, SCB and MPU.
114
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
3.1.1
System Timer (SysTick)
Cortex-M4 includes an integrated system timer, SysTick, which provides a simple, 24-bit
clear-on-write, decrementing, wrap-on-zero counter with a flexible control mechanism. The counter
can be used in several different ways, for example as:
■ An RTOS tick timer that fires at a programmable rate (for example, 100 Hz) and invokes a SysTick
routine.
■ A high-speed alarm timer using the system clock.
■ A variable rate alarm or signal timer—the duration is range-dependent on the reference clock
used and the dynamic range of the counter.
■ A simple counter used to measure time to completion and time used.
■ An internal clock source control based on missing/meeting durations. The COUNT bit in the
STCTRL control and status register can be used to determine if an action completed within a
set duration, as part of a dynamic clock management control loop.
The timer consists of three registers:
■ SysTick Control and Status (STCTRL): A control and status counter to configure its clock,
enable the counter, enable the SysTick interrupt, and determine counter status.
■ SysTick Reload Value (STRELOAD): The reload value for the counter, used to provide the
counter's wrap value.
■ SysTick Current Value (STCURRENT): The current value of the counter.
When enabled, the timer counts down on each clock from the reload value to zero, reloads (wraps)
to the value in the STRELOAD register on the next clock edge, then decrements on subsequent
clocks. Clearing the STRELOAD register disables the counter on the next wrap. When the counter
reaches zero, the COUNT status bit is set. The COUNT bit clears on reads.
Writing to the STCURRENT register clears the register and the COUNT status bit. The write does
not trigger the SysTick exception logic. On a read, the current value is the value of the register at
the time the register is accessed.
The SysTick counter runs on either the system clock or the precision internal oscillator (PIOSC)
divided by 4. If this clock signal is stopped for low power mode, the SysTick counter stops. SysTick
can be kept running during Deep-sleep mode by setting the CLK_SRC bit in the SysTick Control
and Status Register (STCTRL) register and ensuring that the PIOSCPD bit in the Deep Sleep
Clock Configuration (DSLPCLKCFG) register is clear. Ensure software uses aligned word accesses
to access the SysTick registers.
The SysTick counter reload and current value are undefined at reset; the correct initialization
sequence for the SysTick counter is:
1. Program the value in the STRELOAD register.
2. Clear the STCURRENT register by writing to it with any value.
3. Configure the STCTRL register for the required operation.
Note:
When the processor is halted for debugging, the counter does not decrement.
July 17, 2013
115
Texas Instruments-Production Data
Cortex-M4 Peripherals
3.1.2
Nested Vectored Interrupt Controller (NVIC)
This section describes the Nested Vectored Interrupt Controller (NVIC) and the registers it uses.
The NVIC supports:
■ 84 interrupts.
■ A programmable priority level of 0-7 for each interrupt. A higher level corresponds to a lower
priority, so level 0 is the highest interrupt priority.
■ Low-latency exception and interrupt handling.
■ Level and pulse detection of interrupt signals.
■ Dynamic reprioritization of interrupts.
■ Grouping of priority values into group priority and subpriority fields.
■ Interrupt tail-chaining.
■ An external Non-maskable interrupt (NMI).
The processor automatically stacks its state on exception entry and unstacks this state on exception
exit, with no instruction overhead, providing low latency exception handling.
3.1.2.1
Level-Sensitive and Pulse Interrupts
The processor supports both level-sensitive and pulse interrupts. Pulse interrupts are also described
as edge-triggered interrupts.
A level-sensitive interrupt is held asserted until the peripheral deasserts the interrupt signal. Typically
this happens because the ISR accesses the peripheral, causing it to clear the interrupt request. A
pulse interrupt is an interrupt signal sampled synchronously on the rising edge of the processor
clock. To ensure the NVIC detects the interrupt, the peripheral must assert the interrupt signal for
at least one clock cycle, during which the NVIC detects the pulse and latches the interrupt.
When the processor enters the ISR, it automatically removes the pending state from the interrupt
(see “Hardware and Software Control of Interrupts” on page 116 for more information). For a
level-sensitive interrupt, if the signal is not deasserted before the processor returns from the ISR,
the interrupt becomes pending again, and the processor must execute its ISR again. As a result,
the peripheral can hold the interrupt signal asserted until it no longer needs servicing.
3.1.2.2
Hardware and Software Control of Interrupts
The Cortex-M4 latches all interrupts. A peripheral interrupt becomes pending for one of the following
reasons:
■ The NVIC detects that the interrupt signal is High and the interrupt is not active.
■ The NVIC detects a rising edge on the interrupt signal.
■ Software writes to the corresponding interrupt set-pending register bit, or to the Software Trigger
Interrupt (SWTRIG) register to make a Software-Generated Interrupt pending. See the INT bit
in the PEND0 register on page 138 or SWTRIG on page 148.
A pending interrupt remains pending until one of the following:
116
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
■ The processor enters the ISR for the interrupt, changing the state of the interrupt from pending
to active. Then:
– For a level-sensitive interrupt, when the processor returns from the ISR, the NVIC samples
the interrupt signal. If the signal is asserted, the state of the interrupt changes to pending,
which might cause the processor to immediately re-enter the ISR. Otherwise, the state of the
interrupt changes to inactive.
– For a pulse interrupt, the NVIC continues to monitor the interrupt signal, and if this is pulsed
the state of the interrupt changes to pending and active. In this case, when the processor
returns from the ISR the state of the interrupt changes to pending, which might cause the
processor to immediately re-enter the ISR.
If the interrupt signal is not pulsed while the processor is in the ISR, when the processor
returns from the ISR the state of the interrupt changes to inactive.
■ Software writes to the corresponding interrupt clear-pending register bit
– For a level-sensitive interrupt, if the interrupt signal is still asserted, the state of the interrupt
does not change. Otherwise, the state of the interrupt changes to inactive.
– For a pulse interrupt, the state of the interrupt changes to inactive, if the state was pending
or to active, if the state was active and pending.
3.1.3
System Control Block (SCB)
The System Control Block (SCB) provides system implementation information and system control,
including configuration, control, and reporting of the system exceptions.
3.1.4
Memory Protection Unit (MPU)
This section describes the Memory protection unit (MPU). The MPU divides the memory map into
a number of regions and defines the location, size, access permissions, and memory attributes of
each region. The MPU supports independent attribute settings for each region, overlapping regions,
and export of memory attributes to the system.
The memory attributes affect the behavior of memory accesses to the region. The Cortex-M4 MPU
defines eight separate memory regions, 0-7, and a background region.
When memory regions overlap, a memory access is affected by the attributes of the region with the
highest number. For example, the attributes for region 7 take precedence over the attributes of any
region that overlaps region 7.
The background region has the same memory access attributes as the default memory map, but is
accessible from privileged software only.
The Cortex-M4 MPU memory map is unified, meaning that instruction accesses and data accesses
have the same region settings.
If a program accesses a memory location that is prohibited by the MPU, the processor generates
a memory management fault, causing a fault exception and possibly causing termination of the
process in an OS environment. In an OS environment, the kernel can update the MPU region setting
dynamically based on the process to be executed. Typically, an embedded OS uses the MPU for
memory protection.
Configuration of MPU regions is based on memory types (see “Memory Regions, Types and
Attributes” on page 87 for more information).
July 17, 2013
117
Texas Instruments-Production Data
Cortex-M4 Peripherals
Table 3-2 on page 118 shows the possible MPU region attributes. See the section called “MPU
Configuration for a Tiva™ C Series Microcontroller” on page 122 for guidelines for programming a
microcontroller implementation.
Table 3-2. Memory Attributes Summary
Memory Type
Description
Strongly Ordered
All accesses to Strongly Ordered memory occur in program order.
Device
Memory-mapped peripherals
Normal
Normal memory
To avoid unexpected behavior, disable the interrupts before updating the attributes of a region that
the interrupt handlers might access.
Ensure software uses aligned accesses of the correct size to access MPU registers:
■ Except for the MPU Region Attribute and Size (MPUATTR) register, all MPU registers must
be accessed with aligned word accesses.
■ The MPUATTR register can be accessed with byte or aligned halfword or word accesses.
The processor does not support unaligned accesses to MPU registers.
When setting up the MPU, and if the MPU has previously been programmed, disable unused regions
to prevent any previous region settings from affecting the new MPU setup.
3.1.4.1
Updating an MPU Region
To update the attributes for an MPU region, the MPU Region Number (MPUNUMBER), MPU
Region Base Address (MPUBASE) and MPUATTR registers must be updated. Each register can
be programmed separately or with a multiple-word write to program all of these registers. You can
use the MPUBASEx and MPUATTRx aliases to program up to four regions simultaneously using
an STM instruction.
Updating an MPU Region Using Separate Words
This example simple code configures one region:
; R1 = region number
; R2 = size/enable
; R3 = attributes
; R4 = address
LDR R0,=MPUNUMBER
STR R1, [R0, #0x0]
STR R4, [R0, #0x4]
STRH R2, [R0, #0x8]
STRH R3, [R0, #0xA]
;
;
;
;
;
0xE000ED98, MPU region number register
Region Number
Region Base Address
Region Size and Enable
Region Attribute
Disable a region before writing new region settings to the MPU if you have previously enabled the
region being changed. For example:
; R1 = region number
; R2 = size/enable
; R3 = attributes
; R4 = address
LDR R0,=MPUNUMBER
; 0xE000ED98, MPU region number register
118
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
STR R1, [R0, #0x0]
BIC R2, R2, #1
STRH R2, [R0, #0x8]
STR R4, [R0, #0x4]
STRH R3, [R0, #0xA]
ORR R2, #1
STRH R2, [R0, #0x8]
;
;
;
;
;
;
;
Region Number
Disable
Region Size and Enable
Region Base Address
Region Attribute
Enable
Region Size and Enable
Software must use memory barrier instructions:
■ Before MPU setup, if there might be outstanding memory transfers, such as buffered writes, that
might be affected by the change in MPU settings.
■ After MPU setup, if it includes memory transfers that must use the new MPU settings.
However, memory barrier instructions are not required if the MPU setup process starts by entering
an exception handler, or is followed by an exception return, because the exception entry and
exception return mechanism cause memory barrier behavior.
Software does not need any memory barrier instructions during MPU setup, because it accesses
the MPU through the Private Peripheral Bus (PPB), which is a Strongly Ordered memory region.
For example, if all of the memory access behavior is intended to take effect immediately after the
programming sequence, then a DSB instruction and an ISB instruction should be used. A DSB is
required after changing MPU settings, such as at the end of context switch. An ISB is required if
the code that programs the MPU region or regions is entered using a branch or call. If the
programming sequence is entered using a return from exception, or by taking an exception, then
an ISB is not required.
Updating an MPU Region Using Multi-Word Writes
The MPU can be programmed directly using multi-word writes, depending how the information is
divided. Consider the following reprogramming:
; R1 = region number
; R2 = address
; R3 = size, attributes in one
LDR R0, =MPUNUMBER ; 0xE000ED98, MPU region number register
STR R1, [R0, #0x0] ; Region Number
STR R2, [R0, #0x4] ; Region Base Address
STR R3, [R0, #0x8] ; Region Attribute, Size and Enable
An STM instruction can be used to optimize this:
; R1 = region number
; R2 = address
; R3 = size, attributes in one
LDR R0, =MPUNUMBER ; 0xE000ED98, MPU region number register
STM R0, {R1-R3}
; Region number, address, attribute, size and enable
This operation can be done in two words for pre-packed information, meaning that the MPU Region
Base Address (MPUBASE) register (see page 182) contains the required region number and has
the VALID bit set. This method can be used when the data is statically packed, for example in a
boot loader:
July 17, 2013
119
Texas Instruments-Production Data
Cortex-M4 Peripherals
; R1 = address and region number in one
; R2 = size and attributes in one
LDR R0, =MPUBASE
; 0xE000ED9C, MPU Region Base register
STR R1, [R0, #0x0] ; Region base address and region number combined
; with VALID (bit 4) set
STR R2, [R0, #0x4] ; Region Attribute, Size and Enable
Subregions
Regions of 256 bytes or more are divided into eight equal-sized subregions. Set the corresponding
bit in the SRD field of the MPU Region Attribute and Size (MPUATTR) register (see page 184) to
disable a subregion. The least-significant bit of the SRD field controls the first subregion, and the
most-significant bit controls the last subregion. Disabling a subregion means another region
overlapping the disabled range matches instead. If no other enabled region overlaps the disabled
subregion, the MPU issues a fault.
Regions of 32, 64, and 128 bytes do not support subregions. With regions of these sizes, the SRD
field must be configured to 0x00, otherwise the MPU behavior is unpredictable.
Example of SRD Use
Two regions with the same base address overlap. Region one is 128 KB, and region two is 512 KB.
To ensure the attributes from region one apply to the first 128 KB region, configure the SRD field for
region two to 0x03 to disable the first two subregions, as Figure 3-1 on page 120 shows.
Figure 3-1. SRD Use Example
Region 2, with
subregions
Region 1
Base address of both regions
3.1.4.2
Offset from
base address
512KB
448KB
384KB
320KB
256KB
192KB
128KB
Disabled subregion
64KB
Disabled subregion
0
MPU Access Permission Attributes
The access permission bits, TEX, S, C, B, AP, and XN of the MPUATTR register, control access to
the corresponding memory region. If an access is made to an area of memory without the required
permissions, then the MPU generates a permission fault.
Table 3-3 on page 120 shows the encodings for the TEX, C, B, and S access permission bits. All
encodings are shown for completeness, however the current implementation of the Cortex-M4 does
not support the concept of cacheability or shareability. Refer to the section called “MPU Configuration
for a Tiva™ C Series Microcontroller” on page 122 for information on programming the MPU for
TM4C123BE6PZ implementations.
Table 3-3. TEX, S, C, and B Bit Field Encoding
TEX
S
000b
x
000
B
Memory Type
Shareability
Other Attributes
0
0
Strongly Ordered
Shareable
-
a
0
1
Device
Shareable
-
x
C
a
120
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Table 3-3. TEX, S, C, and B Bit Field Encoding (continued)
TEX
S
C
B
Memory Type
Shareability
Other Attributes
000
0
1
0
Normal
Not shareable
000
1
1
0
Normal
Shareable
000
0
1
1
Normal
Not shareable
000
1
1
1
Normal
Shareable
001
0
0
0
Normal
Not shareable
001
1
0
0
Normal
Shareable
Outer and inner
noncacheable.
001
x
a
0
1
Reserved encoding
-
-
a
Outer and inner
write-through. No write
allocate.
001
x
1
0
Reserved encoding
-
-
001
0
1
1
Normal
Not shareable
001
1
1
1
Normal
Shareable
Outer and inner
write-back. Write and
read allocate.
010
x
a
0
0
Device
Not shareable
Nonshared Device.
a
a
010
x
0
1
Reserved encoding
-
-
010
x
1
x
Reserved encoding
-
-
1BB
0
A
A
Normal
Not shareable
1BB
1
A
A
Normal
Shareable
Cached memory (BB =
outer policy, AA = inner
policy).
a
See Table 3-4 for the
encoding of the AA and
BB bits.
a. The MPU ignores the value of this bit.
Table 3-4 on page 121 shows the cache policy for memory attribute encodings with a TEX value in
the range of 0x4-0x7.
Table 3-4. Cache Policy for Memory Attribute Encoding
Encoding, AA or BB
Corresponding Cache Policy
00
Non-cacheable
01
Write back, write and read allocate
10
Write through, no write allocate
11
Write back, no write allocate
Table 3-5 on page 121 shows the AP encodings in the MPUATTR register that define the access
permissions for privileged and unprivileged software.
Table 3-5. AP Bit Field Encoding
AP Bit Field
Privileged
Permissions
Unprivileged
Permissions
Description
000
No access
No access
All accesses generate a permission fault.
001
R/W
No access
Access from privileged software only.
010
R/W
RO
Writes by unprivileged software generate a
permission fault.
011
R/W
R/W
Full access.
100
Unpredictable
Unpredictable
Reserved.
101
RO
No access
Reads by privileged software only.
July 17, 2013
121
Texas Instruments-Production Data
Cortex-M4 Peripherals
Table 3-5. AP Bit Field Encoding (continued)
AP Bit Field
Privileged
Permissions
Unprivileged
Permissions
Description
110
RO
RO
Read-only, by privileged or unprivileged software.
111
RO
RO
Read-only, by privileged or unprivileged software.
MPU Configuration for a Tiva™ C Series Microcontroller
Tiva™ C Series microcontrollers have only a single processor and no caches. As a result, the MPU
should be programmed as shown in Table 3-6 on page 122.
Table 3-6. Memory Region Attributes for Tiva™ C Series Microcontrollers
Memory Region
TEX
S
C
B
Memory Type and Attributes
Flash memory
000b
0
1
0
Normal memory, non-shareable, write-through
Internal SRAM
000b
1
1
0
Normal memory, shareable, write-through
External SRAM
000b
1
1
1
Normal memory, shareable, write-back,
write-allocate
Peripherals
000b
1
0
1
Device memory, shareable
In current Tiva™ C Series microcontroller implementations, the shareability and cache policy
attributes do not affect the system behavior. However, using these settings for the MPU regions
can make the application code more portable. The values given are for typical situations.
3.1.4.3
MPU Mismatch
When an access violates the MPU permissions, the processor generates a memory management
fault (see “Exceptions and Interrupts” on page 84 for more information). The MFAULTSTAT register
indicates the cause of the fault. See page 169 for more information.
3.1.5
Floating-Point Unit (FPU)
This section describes the Floating-Point Unit (FPU) and the registers it uses. The FPU provides:
■ 32-bit instructions for single-precision (C float) data-processing operations
■ Combined multiply and accumulate instructions for increased precision (Fused MAC)
■ Hardware support for conversion, addition, subtraction, multiplication with optional accumulate,
division, and square-root
■ Hardware support for denormals and all IEEE rounding modes
■ 32 dedicated 32-bit single-precision registers, also addressable as 16 double-word registers
■ Decoupled three stage pipeline
The Cortex-M4F FPU fully supports single-precision add, subtract, multiply, divide, multiply and
accumulate, and square root operations. It also provides conversions between fixed-point and
floating-point data formats, and floating-point constant instructions. The FPU provides floating-point
computation functionality that is compliant with the ANSI/IEEE Std 754-2008, IEEE Standard for
Binary Floating-Point Arithmetic, referred to as the IEEE 754 standard. The FPU's single-precision
extension registers can also be accessed as 16 doubleword registers for load, store, and move
operations.
122
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
3.1.5.1
FPU Views of the Register Bank
The FPU provides an extension register file containing 32 single-precision registers. These can be
viewed as:
■ Sixteen 64-bit doubleword registers, D0-D15
■ Thirty-two 32-bit single-word registers, S0-S31
■ A combination of registers from the above views
Figure 3-2. FPU Register Bank
S0
S1
S2
S3
S4
S5
S6
S7
...
S28
S29
S30
S31
D0
D1
D2
D3
...
D14
D15
The mapping between the registers is as follows:
■ S<2n> maps to the least significant half of D<n>
■ S<2n+1> maps to the most significant half of D<n>
For example, you can access the least significant half of the value in D6 by accessing S12, and the
most significant half of the elements by accessing S13.
3.1.5.2
Modes of Operation
The FPU provides three modes of operation to accommodate a variety of applications.
Full-Compliance mode. In Full-Compliance mode, the FPU processes all operations according to
the IEEE 754 standard in hardware.
Flush-to-Zero mode. Setting the FZ bit of the Floating-Point Status and Control (FPSC) register
enables Flush-to-Zero mode. In this mode, the FPU treats all subnormal input operands of arithmetic
CDP operations as zeros in the operation. Exceptions that result from a zero operand are signalled
appropriately. VABS, VNEG, and VMOV are not considered arithmetic CDP operations and are not
affected by Flush-to-Zero mode. A result that is tiny, as described in the IEEE 754 standard, where
the destination precision is smaller in magnitude than the minimum normal value before rounding,
is replaced with a zero. The IDC bit in FPSC indicates when an input flush occurs. The UFC bit in
FPSC indicates when a result flush occurs.
Default NaN mode. Setting the DN bit in the FPSC register enables default NaN mode. In this mode,
the result of any arithmetic data processing operation that involves an input NaN, or that generates
a NaN result, returns the default NaN. Propagation of the fraction bits is maintained only by VABS,
July 17, 2013
123
Texas Instruments-Production Data
Cortex-M4 Peripherals
VNEG, and VMOV operations. All other CDP operations ignore any information in the fraction bits
of an input NaN.
3.1.5.3
Compliance with the IEEE 754 standard
When Default NaN (DN) and Flush-to-Zero (FZ) modes are disabled, FPv4 functionality is compliant
with the IEEE 754 standard in hardware. No support code is required to achieve this compliance.
3.1.5.4
Complete Implementation of the IEEE 754 standard
The Cortex-M4F floating point instruction set does not support all operations defined in the IEEE
754-2008 standard. Unsupported operations include, but are not limited to the following:
■ Remainder
■ Round floating-point number to integer-valued floating-point number
■ Binary-to-decimal conversions
■ Decimal-to-binary conversions
■ Direct comparison of single-precision and double-precision values
The Cortex-M4 FPU supports fused MAC operations as described in the IEEE standard. For complete
implementation of the IEEE 754-2008 standard, floating-point functionality must be augmented with
library functions.
3.1.5.5
IEEE 754 standard implementation choices
NaN handling
All single-precision values with the maximum exponent field value and a nonzero fraction field are
valid NaNs. A most-significant fraction bit of zero indicates a Signaling NaN (SNaN). A one indicates
a Quiet NaN (QNaN). Two NaN values are treated as different NaNs if they differ in any bit. The
below table shows the default NaN values.
Sign
Fraction
Fraction
0
0xFF
bit [22] = 1, bits [21:0] are all zeros
Processing of input NaNs for ARM floating-point functionality and libraries is defined as follows:
■ In full-compliance mode, NaNs are handled as described in the ARM Architecture Reference
Manual. The hardware processes the NaNs directly for arithmetic CDP instructions. For data
transfer operations, NaNs are transferred without raising the Invalid Operation exception. For
the non-arithmetic CDP instructions, VABS, VNEG, and VMOV, NaNs are copied, with a change
of sign if specified in the instructions, without causing the Invalid Operation exception.
■ In default NaN mode, arithmetic CDP instructions involving NaN operands return the default
NaN regardless of the fractions of any NaN operands. SNaNs in an arithmetic CDP operation
set the IOC flag, FPSCR[0]. NaN handling by data transfer and non-arithmetic CDP instructions
is the same as in full-compliance mode.
124
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Table 3-7. QNaN and SNaN Handling
Instruction Type
Default NaN
Mode
With QNaN Operand
With SNaN Operand
Off
The QNaN or one of the QNaN operands,
if there is more than one, is returned
according to the rules given in the ARM
Architecture Reference Manual.
IOC set. The SNaN is quieted and the
result NaN is determined by the rules
given in the ARM Architecture Reference
Manual.
On
Default NaN returns.
IOC set. Default NaN returns.
Arithmetic CDP
Non-arithmetic CDP Off/On
a
a
NaN passes to destination with sign changed as appropriate.
FCMP(Z)
-
Unordered compare.
IOC set. Unordered compare.
FCMPE(Z)
-
IOC set. Unordered compare.
IOC set. Unordered compare.
Load/store
Off/On
All NaNs transferred.
a. IOC is the Invalid Operation exception flag, FPSCR[0].
Comparisons
Comparison results modify the flags in the FPSCR. You can use the MVRS APSR_nzcv instruction
(formerly FMSTAT) to transfer the current flags from the FPSCR to the APSR. See the ARM
Architecture Reference Manual for mapping of IEEE 754-2008 standard predicates to ARM conditions.
The flags used are chosen so that subsequent conditional execution of ARM instructions can test
the predicates defined in the IEEE standard.
Underflow
The Cortex-M4F FPU uses the before rounding form of tininess and the inexact result form of loss
of accuracy as described in the IEEE 754-2008 standard to generate Underflow exceptions.
In flush-to-zero mode, results that are tiny before rounding, as described in the IEEE standard, are
flushed to a zero, and the UFC flag, FPSCR[3], is set. See the ARM Architecture Reference Manual
for information on flush-to-zero mode.
When the FPU is not in flush-to-zero mode, operations are performed on subnormal operands. If
the operation does not produce a tiny result, it returns the computed result, and the UFC flag,
FPSCR[3], is not set. The IXC flag, FPSCR[4], is set if the operation is inexact. If the operation
produces a tiny result, the result is a subnormal or zero value, and the UFC flag, FPSCR[3], is set
if the result was also inexact.
3.1.5.6
Exceptions
The FPU sets the cumulative exception status flag in the FPSCR register as required for each
instruction, in accordance with the FPv4 architecture. The FPU does not support user-mode traps.
The exception enable bits in the FPSCR read-as-zero, and writes are ignored. The processor also
has six output pins, FPIXC, FPUFC, FPOFC, FPDZC, FPIDC, and FPIOC, that each reflect the
status of one of the cumulative exception flags. For a description of these outputs, see the ARM
Cortex-M4 Integration and Implementation Manual (ARM DII 0239, available from ARM).
The processor can reduce the exception latency by using lazy stacking. See Auxiliary Control
Register, ACTLR on page 4-5. This means that the processor reserves space on the stack for the
FP state, but does not save that state information to the stack. See the ARMv7-M Architecture
Reference Manual (available from ARM) for more information.
3.1.5.7
Enabling the FPU
The FPU is disabled from reset. You must enable it before you can use any floating-point instructions.
The processor must be in privileged mode to read from and write to the Coprocessor Access
July 17, 2013
125
Texas Instruments-Production Data
Cortex-M4 Peripherals
Control (CPAC) register. The below example code sequence enables the FPU in both privileged
and user modes.
; CPACR is located at address 0xE000ED88
LDR.W R0, =0xE000ED88
; Read CPACR
LDR R1, [R0]
; Set bits 20-23 to enable CP10 and CP11 coprocessors
ORR R1, R1, #(0xF << 20)
; Write back the modified value to the CPACR
STR R1, [R0]; wait for store to complete
DSB
;reset pipeline now the FPU is enabled
ISB
3.2
Register Map
Table 3-8 on page 126 lists the Cortex-M4 Peripheral SysTick, NVIC, MPU, FPU and SCB registers.
The offset listed is a hexadecimal increment to the register's address, relative to the Core Peripherals
base address of 0xE000.E000.
Note:
Register spaces that are not used are reserved for future or internal use. Software should
not modify any reserved memory address.
Table 3-8. Peripherals Register Map
Offset
Name
Type
Reset
Description
See
page
System Timer (SysTick) Registers
0x010
STCTRL
R/W
0x0000.0004
SysTick Control and Status Register
130
0x014
STRELOAD
R/W
-
SysTick Reload Value Register
132
0x018
STCURRENT
R/WC
-
SysTick Current Value Register
133
Nested Vectored Interrupt Controller (NVIC) Registers
0x100
EN0
R/W
0x0000.0000
Interrupt 0-31 Set Enable
134
0x104
EN1
R/W
0x0000.0000
Interrupt 32-63 Set Enable
134
0x108
EN2
R/W
0x0000.0000
Interrupt 64-95 Set Enable
134
0x10C
EN3
R/W
0x0000.0000
Interrupt 96-127 Set Enable
134
0x110
EN4
R/W
0x0000.0000
Interrupt 128-138 Set Enable
135
0x180
DIS0
R/W
0x0000.0000
Interrupt 0-31 Clear Enable
136
0x184
DIS1
R/W
0x0000.0000
Interrupt 32-63 Clear Enable
136
0x188
DIS2
R/W
0x0000.0000
Interrupt 64-95 Clear Enable
136
0x18C
DIS3
R/W
0x0000.0000
Interrupt 96-127 Clear Enable
136
0x190
DIS4
R/W
0x0000.0000
Interrupt 128-138 Clear Enable
137
0x200
PEND0
R/W
0x0000.0000
Interrupt 0-31 Set Pending
138
0x204
PEND1
R/W
0x0000.0000
Interrupt 32-63 Set Pending
138
126
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Table 3-8. Peripherals Register Map (continued)
Description
See
page
Offset
Name
Type
Reset
0x208
PEND2
R/W
0x0000.0000
Interrupt 64-95 Set Pending
138
0x20C
PEND3
R/W
0x0000.0000
Interrupt 96-127 Set Pending
138
0x210
PEND4
R/W
0x0000.0000
Interrupt 128-138 Set Pending
139
0x280
UNPEND0
R/W
0x0000.0000
Interrupt 0-31 Clear Pending
140
0x284
UNPEND1
R/W
0x0000.0000
Interrupt 32-63 Clear Pending
140
0x288
UNPEND2
R/W
0x0000.0000
Interrupt 64-95 Clear Pending
140
0x28C
UNPEND3
R/W
0x0000.0000
Interrupt 96-127 Clear Pending
140
0x290
UNPEND4
R/W
0x0000.0000
Interrupt 128-138 Clear Pending
141
0x300
ACTIVE0
RO
0x0000.0000
Interrupt 0-31 Active Bit
142
0x304
ACTIVE1
RO
0x0000.0000
Interrupt 32-63 Active Bit
142
0x308
ACTIVE2
RO
0x0000.0000
Interrupt 64-95 Active Bit
142
0x30C
ACTIVE3
RO
0x0000.0000
Interrupt 96-127 Active Bit
142
0x310
ACTIVE4
RO
0x0000.0000
Interrupt 128-138 Active Bit
143
0x400
PRI0
R/W
0x0000.0000
Interrupt 0-3 Priority
144
0x404
PRI1
R/W
0x0000.0000
Interrupt 4-7 Priority
144
0x408
PRI2
R/W
0x0000.0000
Interrupt 8-11 Priority
144
0x40C
PRI3
R/W
0x0000.0000
Interrupt 12-15 Priority
144
0x410
PRI4
R/W
0x0000.0000
Interrupt 16-19 Priority
144
0x414
PRI5
R/W
0x0000.0000
Interrupt 20-23 Priority
144
0x418
PRI6
R/W
0x0000.0000
Interrupt 24-27 Priority
144
0x41C
PRI7
R/W
0x0000.0000
Interrupt 28-31 Priority
144
0x420
PRI8
R/W
0x0000.0000
Interrupt 32-35 Priority
144
0x424
PRI9
R/W
0x0000.0000
Interrupt 36-39 Priority
144
0x428
PRI10
R/W
0x0000.0000
Interrupt 40-43 Priority
144
0x42C
PRI11
R/W
0x0000.0000
Interrupt 44-47 Priority
144
0x430
PRI12
R/W
0x0000.0000
Interrupt 48-51 Priority
144
0x434
PRI13
R/W
0x0000.0000
Interrupt 52-55 Priority
144
0x438
PRI14
R/W
0x0000.0000
Interrupt 56-59 Priority
144
0x43C
PRI15
R/W
0x0000.0000
Interrupt 60-63 Priority
144
0x440
PRI16
R/W
0x0000.0000
Interrupt 64-67 Priority
146
0x444
PRI17
R/W
0x0000.0000
Interrupt 68-71 Priority
146
0x448
PRI18
R/W
0x0000.0000
Interrupt 72-75 Priority
146
July 17, 2013
127
Texas Instruments-Production Data
Cortex-M4 Peripherals
Table 3-8. Peripherals Register Map (continued)
Description
See
page
Offset
Name
Type
Reset
0x44C
PRI19
R/W
0x0000.0000
Interrupt 76-79 Priority
146
0x450
PRI20
R/W
0x0000.0000
Interrupt 80-83 Priority
146
0x454
PRI21
R/W
0x0000.0000
Interrupt 84-87 Priority
146
0x458
PRI22
R/W
0x0000.0000
Interrupt 88-91 Priority
146
0x45C
PRI23
R/W
0x0000.0000
Interrupt 92-95 Priority
146
0x460
PRI24
R/W
0x0000.0000
Interrupt 96-99 Priority
146
0x464
PRI25
R/W
0x0000.0000
Interrupt 100-103 Priority
146
0x468
PRI26
R/W
0x0000.0000
Interrupt 104-107 Priority
146
0x46C
PRI27
R/W
0x0000.0000
Interrupt 108-111 Priority
146
0x470
PRI28
R/W
0x0000.0000
Interrupt 112-115 Priority
146
0x474
PRI29
R/W
0x0000.0000
Interrupt 116-119 Priority
146
0x478
PRI30
R/W
0x0000.0000
Interrupt 120-123 Priority
146
0x47C
PRI31
R/W
0x0000.0000
Interrupt 124-127 Priority
146
0x480
PRI32
R/W
0x0000.0000
Interrupt 128-131 Priority
146
0x484
PRI33
R/W
0x0000.0000
Interrupt 132-135 Priority
146
0x488
PRI34
R/W
0x0000.0000
Interrupt 136-138 Priority
146
0xF00
SWTRIG
WO
0x0000.0000
Software Trigger Interrupt
148
System Control Block (SCB) Registers
0x008
ACTLR
R/W
0x0000.0000
Auxiliary Control
149
0xD00
CPUID
RO
0x410F.C241
CPU ID Base
151
0xD04
INTCTRL
R/W
0x0000.0000
Interrupt Control and State
152
0xD08
VTABLE
R/W
0x0000.0000
Vector Table Offset
155
0xD0C
APINT
R/W
0xFA05.0000
Application Interrupt and Reset Control
156
0xD10
SYSCTRL
R/W
0x0000.0000
System Control
158
0xD14
CFGCTRL
R/W
0x0000.0200
Configuration and Control
160
0xD18
SYSPRI1
R/W
0x0000.0000
System Handler Priority 1
162
0xD1C
SYSPRI2
R/W
0x0000.0000
System Handler Priority 2
163
0xD20
SYSPRI3
R/W
0x0000.0000
System Handler Priority 3
164
0xD24
SYSHNDCTRL
R/W
0x0000.0000
System Handler Control and State
165
0xD28
FAULTSTAT
R/W1C
0x0000.0000
Configurable Fault Status
169
0xD2C
HFAULTSTAT
R/W1C
0x0000.0000
Hard Fault Status
175
0xD34
MMADDR
R/W
-
Memory Management Fault Address
176
128
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Table 3-8. Peripherals Register Map (continued)
Offset
Name
Type
Reset
0xD38
FAULTADDR
R/W
-
Description
See
page
Bus Fault Address
177
Memory Protection Unit (MPU) Registers
0xD90
MPUTYPE
RO
0x0000.0800
MPU Type
178
0xD94
MPUCTRL
R/W
0x0000.0000
MPU Control
179
0xD98
MPUNUMBER
R/W
0x0000.0000
MPU Region Number
181
0xD9C
MPUBASE
R/W
0x0000.0000
MPU Region Base Address
182
0xDA0
MPUATTR
R/W
0x0000.0000
MPU Region Attribute and Size
184
0xDA4
MPUBASE1
R/W
0x0000.0000
MPU Region Base Address Alias 1
182
0xDA8
MPUATTR1
R/W
0x0000.0000
MPU Region Attribute and Size Alias 1
184
0xDAC
MPUBASE2
R/W
0x0000.0000
MPU Region Base Address Alias 2
182
0xDB0
MPUATTR2
R/W
0x0000.0000
MPU Region Attribute and Size Alias 2
184
0xDB4
MPUBASE3
R/W
0x0000.0000
MPU Region Base Address Alias 3
182
0xDB8
MPUATTR3
R/W
0x0000.0000
MPU Region Attribute and Size Alias 3
184
Floating-Point Unit (FPU) Registers
0xD88
CPAC
R/W
0x0000.0000
Coprocessor Access Control
187
0xF34
FPCC
R/W
0xC000.0000
Floating-Point Context Control
188
0xF38
FPCA
R/W
-
Floating-Point Context Address
190
0xF3C
FPDSC
R/W
0x0000.0000
Floating-Point Default Status Control
191
3.3
System Timer (SysTick) Register Descriptions
This section lists and describes the System Timer registers, in numerical order by address offset.
July 17, 2013
129
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 1: SysTick Control and Status Register (STCTRL), offset 0x010
Note:
This register can only be accessed from privileged mode.
The SysTick STCTRL register enables the SysTick features.
SysTick Control and Status Register (STCTRL)
Base 0xE000.E000
Offset 0x010
Type R/W, reset 0x0000.0004
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
4
3
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
16
COUNT
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
2
1
0
CLK_SRC
INTEN
ENABLE
R/W
1
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:17
reserved
RO
0x000
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
16
COUNT
RO
0
Count Flag
Value
Description
0
The SysTick timer has not counted to 0 since the last time
this bit was read.
1
The SysTick timer has counted to 0 since the last time
this bit was read.
This bit is cleared by a read of the register or if the STCURRENT register
is written with any value.
If read by the debugger using the DAP, this bit is cleared only if the
MasterType bit in the AHB-AP Control Register is clear. Otherwise,
the COUNT bit is not changed by the debugger read. See the ARM®
Debug Interface V5 Architecture Specification for more information on
MasterType.
15:3
reserved
RO
0x000
2
CLK_SRC
R/W
1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Clock Source
Value Description
0
Precision internal oscillator (PIOSC) divided by 4
1
System clock
130
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
1
INTEN
R/W
0
0
ENABLE
R/W
0
Description
Interrupt Enable
Value
Description
0
Interrupt generation is disabled. Software can use the
COUNT bit to determine if the counter has ever reached 0.
1
An interrupt is generated to the NVIC when SysTick counts
to 0.
Enable
Value
Description
0
The counter is disabled.
1
Enables SysTick to operate in a multi-shot way. That is, the
counter loads the RELOAD value and begins counting down.
On reaching 0, the COUNT bit is set and an interrupt is
generated if enabled by INTEN. The counter then loads the
RELOAD value again and begins counting.
July 17, 2013
131
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 2: SysTick Reload Value Register (STRELOAD), offset 0x014
Note:
This register can only be accessed from privileged mode.
The STRELOAD register specifies the start value to load into the SysTick Current Value
(STCURRENT) register when the counter reaches 0. The start value can be between 0x1 and
0x00FF.FFFF. A start value of 0 is possible but has no effect because the SysTick interrupt and the
COUNT bit are activated when counting from 1 to 0.
SysTick can be configured as a multi-shot timer, repeated over and over, firing every N+1 clock
pulses, where N is any value from 1 to 0x00FF.FFFF. For example, if a tick interrupt is required
every 100 clock pulses, 99 must be written into the RELOAD field.
Note that in order to access this register correctly, the system clock must be faster than 8 MHz.
SysTick Reload Value Register (STRELOAD)
Base 0xE000.E000
Offset 0x014
Type R/W, reset 31
30
29
28
27
26
25
24
23
22
21
20
reserved
Type
Reset
19
18
17
16
RELOAD
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
RELOAD
Type
Reset
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:24
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23:0
RELOAD
R/W
0x00.0000
Reload Value
Value to load into the SysTick Current Value (STCURRENT) register
when the counter reaches 0.
132
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 3: SysTick Current Value Register (STCURRENT), offset 0x018
Note:
This register can only be accessed from privileged mode.
The STCURRENT register contains the current value of the SysTick counter.
SysTick Current Value Register (STCURRENT)
Base 0xE000.E000
Offset 0x018
Type R/WC, reset 31
30
29
28
27
26
25
24
23
22
21
reserved
Type
Reset
20
19
18
17
16
CURRENT
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/WC
0
R/WC
0
R/WC
0
R/WC
0
R/WC
0
R/WC
0
R/WC
0
R/WC
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R/WC
0
R/WC
0
R/WC
0
R/WC
0
R/WC
0
R/WC
0
R/WC
0
CURRENT
Type
Reset
R/WC
0
R/WC
0
R/WC
0
R/WC
0
R/WC
0
R/WC
0
R/WC
0
R/WC
0
R/WC
0
Bit/Field
Name
Type
Reset
Description
31:24
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23:0
CURRENT
R/WC
0x00.0000
Current Value
This field contains the current value at the time the register is accessed.
No read-modify-write protection is provided, so change with care.
This register is write-clear. Writing to it with any value clears the register.
Clearing this register also clears the COUNT bit of the STCTRL register.
3.4
NVIC Register Descriptions
This section lists and describes the NVIC registers, in numerical order by address offset.
The NVIC registers can only be fully accessed from privileged mode, but interrupts can be pended
while in unprivileged mode by enabling the Configuration and Control (CFGCTRL) register. Any
other unprivileged mode access causes a bus fault.
Ensure software uses correctly aligned register accesses. The processor does not support unaligned
accesses to NVIC registers.
An interrupt can enter the pending state even if it is disabled.
Before programming the VTABLE register to relocate the vector table, ensure the vector table
entries of the new vector table are set up for fault handlers, NMI, and all enabled exceptions such
as interrupts. For more information, see page 155.
July 17, 2013
133
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 4: Interrupt 0-31 Set Enable (EN0), offset 0x100
Register 5: Interrupt 32-63 Set Enable (EN1), offset 0x104
Register 6: Interrupt 64-95 Set Enable (EN2), offset 0x108
Register 7: Interrupt 96-127 Set Enable (EN3), offset 0x10C
Note:
This register can only be accessed from privileged mode.
The ENn registers enable interrupts and show which interrupts are enabled. Bit 0 of EN0 corresponds
to Interrupt 0; bit 31 corresponds to Interrupt 31. Bit 0 of EN1 corresponds to Interrupt 32; bit 31
corresponds to Interrupt 63. Bit 0 of EN2 corresponds to Interrupt 64; bit 31 corresponds to Interrupt
95. Bit 0 of EN3 corresponds to Interrupt 96; bit 31 corresponds to Interrupt 127. Bit 0 of EN4 (see
page 135) corresponds to Interrupt 128; bit 10 corresponds to Interrupt 138.
See Table 2-9 on page 96 for interrupt assignments.
If a pending interrupt is enabled, the NVIC activates the interrupt based on its priority. If an interrupt
is not enabled, asserting its interrupt signal changes the interrupt state to pending, but the NVIC
never activates the interrupt, regardless of its priority.
Interrupt 0-31 Set Enable (EN0)
Base 0xE000.E000
Offset 0x100
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
7
6
5
4
3
2
1
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
INT
Type
Reset
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
15
14
13
12
11
10
9
8
INT
Type
Reset
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit/Field
Name
Type
31:0
INT
R/W
R/W
0
Reset
R/W
0
Description
0x0000.0000 Interrupt Enable
Value
Description
0
On a read, indicates the interrupt is disabled.
On a write, no effect.
1
On a read, indicates the interrupt is enabled.
On a write, enables the interrupt.
A bit can only be cleared by setting the corresponding INT[n] bit in
the DISn register.
134
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 8: Interrupt 128-138 Set Enable (EN4), offset 0x110
Note:
This register can only be accessed from privileged mode.
The EN4 register enables interrupts and shows which interrupts are enabled. Bit 0 corresponds to
Interrupt 128; bit 10 corresponds to Interrupt 138. See Table 2-9 on page 96 for interrupt assignments.
If a pending interrupt is enabled, the NVIC activates the interrupt based on its priority. If an interrupt
is not enabled, asserting its interrupt signal changes the interrupt state to pending, but the NVIC
never activates the interrupt, regardless of its priority.
Interrupt 128-138 Set Enable (EN4)
Base 0xE000.E000
Offset 0x110
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
INT
Bit/Field
Name
Type
Reset
31:11
reserved
RO
0x0000.000
10:0
INT
R/W
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Interrupt Enable
Value
Description
0
On a read, indicates the interrupt is disabled.
On a write, no effect.
1
On a read, indicates the interrupt is enabled.
On a write, enables the interrupt.
A bit can only be cleared by setting the corresponding INT[n] bit in
the DIS4 register.
July 17, 2013
135
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 9: Interrupt 0-31 Clear Enable (DIS0), offset 0x180
Register 10: Interrupt 32-63 Clear Enable (DIS1), offset 0x184
Register 11: Interrupt 64-95 Clear Enable (DIS2), offset 0x188
Register 12: Interrupt 96-127 Clear Enable (DIS3), offset 0x18C
Note:
This register can only be accessed from privileged mode.
The DISn registers disable interrupts. Bit 0 of DIS0 corresponds to Interrupt 0; bit 31 corresponds
to Interrupt 31. Bit 0 of DIS1 corresponds to Interrupt 32; bit 31 corresponds to Interrupt 63. Bit 0 of
DIS2 corresponds to Interrupt 64; bit 31 corresponds to Interrupt 95. Bit 0 of DIS3 corresponds to
Interrupt 96; bit 31 corresponds to Interrupt 127. Bit 0 of DIS4 (see page 137) corresponds to Interrupt
128; bit 10 corresponds to Interrupt 138.
See Table 2-9 on page 96 for interrupt assignments.
Interrupt 0-31 Clear Enable (DIS0)
Base 0xE000.E000
Offset 0x180
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
INT
Type
Reset
INT
Type
Reset
Bit/Field
Name
Type
31:0
INT
R/W
Reset
Description
0x0000.0000 Interrupt Disable
Value Description
0
On a read, indicates the interrupt is disabled.
On a write, no effect.
1
On a read, indicates the interrupt is enabled.
On a write, clears the corresponding INT[n] bit in the EN0
register, disabling interrupt [n].
136
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 13: Interrupt 128-138 Clear Enable (DIS4), offset 0x190
Note:
This register can only be accessed from privileged mode.
The DIS4 register disables interrupts. Bit 0 corresponds to Interrupt 128; bit 10 corresponds to
Interrupt 138. See Table 2-9 on page 96 for interrupt assignments.
Interrupt 128-138 Clear Enable (DIS4)
Base 0xE000.E000
Offset 0x190
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
RO
0
RO
0
15
14
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
INT
RO
0
RO
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
31:11
reserved
RO
0x0000.000
10:0
INT
R/W
0x0
R/W
0
R/W
0
R/W
0
R/W
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Interrupt Disable
Value Description
0
On a read, indicates the interrupt is disabled.
On a write, no effect.
1
On a read, indicates the interrupt is enabled.
On a write, clears the corresponding INT[n] bit in the EN4
register, disabling interrupt [n].
July 17, 2013
137
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 14: Interrupt 0-31 Set Pending (PEND0), offset 0x200
Register 15: Interrupt 32-63 Set Pending (PEND1), offset 0x204
Register 16: Interrupt 64-95 Set Pending (PEND2), offset 0x208
Register 17: Interrupt 96-127 Set Pending (PEND3), offset 0x20C
Note:
This register can only be accessed from privileged mode.
The PENDn registers force interrupts into the pending state and show which interrupts are pending.
Bit 0 of PEND0 corresponds to Interrupt 0; bit 31 corresponds to Interrupt 31. Bit 0 of PEND1
corresponds to Interrupt 32; bit 31 corresponds to Interrupt 63. Bit 0 of PEND2 corresponds to
Interrupt 64; bit 31 corresponds to Interrupt 95. Bit 0 of PEND3 corresponds to Interrupt 96; bit 31
corresponds to Interrupt 127. Bit 0 of PEND4 (see page 139) corresponds to Interrupt 128; bit 10
corresponds to Interrupt 138.
See Table 2-9 on page 96 for interrupt assignments.
Interrupt 0-31 Set Pending (PEND0)
Base 0xE000.E000
Offset 0x200
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
INT
Type
Reset
INT
Type
Reset
Bit/Field
Name
Type
31:0
INT
R/W
Reset
Description
0x0000.0000 Interrupt Set Pending
Value
Description
0
On a read, indicates that the interrupt is not pending.
On a write, no effect.
1
On a read, indicates that the interrupt is pending.
On a write, the corresponding interrupt is set to pending
even if it is disabled.
If the corresponding interrupt is already pending, setting a bit has no
effect.
A bit can only be cleared by setting the corresponding INT[n] bit in
the UNPEND0 register.
138
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 18: Interrupt 128-138 Set Pending (PEND4), offset 0x210
Note:
This register can only be accessed from privileged mode.
The PEND4 register forces interrupts into the pending state and shows which interrupts are pending.
Bit 0 corresponds to Interrupt 128; bit 10 corresponds to Interrupt 138. See Table 2-9 on page 96
for interrupt assignments.
Interrupt 128-138 Set Pending (PEND4)
Base 0xE000.E000
Offset 0x210
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
RO
0
RO
0
15
14
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
INT
RO
0
RO
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
31:11
reserved
RO
0x0000.000
10:0
INT
R/W
0x0
R/W
0
R/W
0
R/W
0
R/W
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Interrupt Set Pending
Value
Description
0
On a read, indicates that the interrupt is not pending.
On a write, no effect.
1
On a read, indicates that the interrupt is pending.
On a write, the corresponding interrupt is set to pending
even if it is disabled.
If the corresponding interrupt is already pending, setting a bit has no
effect.
A bit can only be cleared by setting the corresponding INT[n] bit in
the UNPEND4 register.
July 17, 2013
139
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 19: Interrupt 0-31 Clear Pending (UNPEND0), offset 0x280
Register 20: Interrupt 32-63 Clear Pending (UNPEND1), offset 0x284
Register 21: Interrupt 64-95 Clear Pending (UNPEND2), offset 0x288
Register 22: Interrupt 96-127 Clear Pending (UNPEND3), offset 0x28C
Note:
This register can only be accessed from privileged mode.
The UNPENDn registers show which interrupts are pending and remove the pending state from
interrupts. Bit 0 of UNPEND0 corresponds to Interrupt 0; bit 31 corresponds to Interrupt 31. Bit 0 of
UNPEND1 corresponds to Interrupt 32; bit 31 corresponds to Interrupt 63. Bit 0 of UNPEND2
corresponds to Interrupt 64; bit 31 corresponds to Interrupt 95. Bit 0 of UNPEND3 corresponds to
Interrupt 96; bit 31 corresponds to Interrupt 127. Bit 0 of UNPEND4 (see page 141) corresponds to
Interrupt 128; bit 10 corresponds to Interrupt 138.
See Table 2-9 on page 96 for interrupt assignments.
Interrupt 0-31 Clear Pending (UNPEND0)
Base 0xE000.E000
Offset 0x280
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
INT
Type
Reset
INT
Type
Reset
Bit/Field
Name
Type
31:0
INT
R/W
Reset
Description
0x0000.0000 Interrupt Clear Pending
Value Description
0
On a read, indicates that the interrupt is not pending.
On a write, no effect.
1
On a read, indicates that the interrupt is pending.
On a write, clears the corresponding INT[n] bit in the PEND0
register, so that interrupt [n] is no longer pending.
Setting a bit does not affect the active state of the corresponding
interrupt.
140
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 23: Interrupt 128-138 Clear Pending (UNPEND4), offset 0x290
Note:
This register can only be accessed from privileged mode.
The UNPEND4 register shows which interrupts are pending and removes the pending state from
interrupts. Bit 0 corresponds to Interrupt 128; bit 10 corresponds to Interrupt 138. See Table
2-9 on page 96 for interrupt assignments.
Interrupt 128-138 Clear Pending (UNPEND4)
Base 0xE000.E000
Offset 0x290
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
RO
0
RO
0
15
14
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
INT
RO
0
RO
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
31:11
reserved
RO
0x0000.000
10:0
INT
R/W
0x0
R/W
0
R/W
0
R/W
0
R/W
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Interrupt Clear Pending
Value Description
0
On a read, indicates that the interrupt is not pending.
On a write, no effect.
1
On a read, indicates that the interrupt is pending.
On a write, clears the corresponding INT[n] bit in the PEND4
register, so that interrupt [n] is no longer pending.
Setting a bit does not affect the active state of the corresponding
interrupt.
July 17, 2013
141
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 24: Interrupt 0-31 Active Bit (ACTIVE0), offset 0x300
Register 25: Interrupt 32-63 Active Bit (ACTIVE1), offset 0x304
Register 26: Interrupt 64-95 Active Bit (ACTIVE2), offset 0x308
Register 27: Interrupt 96-127 Active Bit (ACTIVE3), offset 0x30C
Note:
This register can only be accessed from privileged mode.
The UNPENDn registers indicate which interrupts are active. Bit 0 of ACTIVE0 corresponds to
Interrupt 0; bit 31 corresponds to Interrupt 31. Bit 0 of ACTIVE1 corresponds to Interrupt 32; bit 31
corresponds to Interrupt 63. Bit 0 of ACTIVE2 corresponds to Interrupt 64; bit 31 corresponds to
Interrupt 95. Bit 0 of ACTIVE3 corresponds to Interrupt 96; bit 31 corresponds to Interrupt 127. Bit
0 of ACTIVE4 (see page 143) corresponds to Interrupt 128; bit 10 corresponds to Interrupt 138.
See Table 2-9 on page 96 for interrupt assignments.
Caution – Do not manually set or clear the bits in this register.
Interrupt 0-31 Active Bit (ACTIVE0)
Base 0xE000.E000
Offset 0x300
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
INT
Type
Reset
INT
Type
Reset
Bit/Field
Name
Type
31:0
INT
RO
Reset
Description
0x0000.0000 Interrupt Active
Value Description
0
The corresponding interrupt is not active.
1
The corresponding interrupt is active, or active and pending.
142
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 28: Interrupt 128-138 Active Bit (ACTIVE4), offset 0x310
Note:
This register can only be accessed from privileged mode.
The ACTIVE4 register indicates which interrupts are active. Bit 0 corresponds to Interrupt 128; bit
10 corresponds to Interrupt 131. See Table 2-9 on page 96 for interrupt assignments.
Caution – Do not manually set or clear the bits in this register.
Interrupt 128-138 Active Bit (ACTIVE4)
Base 0xE000.E000
Offset 0x310
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
15
14
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
INT
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:11
reserved
RO
0x0000.000
10:0
INT
RO
0x0
RO
0
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Interrupt Active
Value Description
0
The corresponding interrupt is not active.
1
The corresponding interrupt is active, or active and pending.
July 17, 2013
143
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 29: Interrupt 0-3 Priority (PRI0), offset 0x400
Register 30: Interrupt 4-7 Priority (PRI1), offset 0x404
Register 31: Interrupt 8-11 Priority (PRI2), offset 0x408
Register 32: Interrupt 12-15 Priority (PRI3), offset 0x40C
Register 33: Interrupt 16-19 Priority (PRI4), offset 0x410
Register 34: Interrupt 20-23 Priority (PRI5), offset 0x414
Register 35: Interrupt 24-27 Priority (PRI6), offset 0x418
Register 36: Interrupt 28-31 Priority (PRI7), offset 0x41C
Register 37: Interrupt 32-35 Priority (PRI8), offset 0x420
Register 38: Interrupt 36-39 Priority (PRI9), offset 0x424
Register 39: Interrupt 40-43 Priority (PRI10), offset 0x428
Register 40: Interrupt 44-47 Priority (PRI11), offset 0x42C
Register 41: Interrupt 48-51 Priority (PRI12), offset 0x430
Register 42: Interrupt 52-55 Priority (PRI13), offset 0x434
Register 43: Interrupt 56-59 Priority (PRI14), offset 0x438
Register 44: Interrupt 60-63 Priority (PRI15), offset 0x43C
Note:
This register can only be accessed from privileged mode.
The PRIn registers (see also page 146) provide 3-bit priority fields for each interrupt. These registers
are byte accessible. Each register holds four priority fields that are assigned to interrupts as follows:
PRIn Register Bit Field
Interrupt
Bits 31:29
Interrupt [4n+3]
Bits 23:21
Interrupt [4n+2]
Bits 15:13
Interrupt [4n+1]
Bits 7:5
Interrupt [4n]
See Table 2-9 on page 96 for interrupt assignments.
Each priority level can be split into separate group priority and subpriority fields. The PRIGROUP
field in the Application Interrupt and Reset Control (APINT) register (see page 156) indicates the
position of the binary point that splits the priority and subpriority fields.
These registers can only be accessed from privileged mode.
144
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Interrupt 0-3 Priority (PRI0)
Base 0xE000.E000
Offset 0x400
Type R/W, reset 0x0000.0000
31
30
29
28
27
INTD
Type
Reset
25
24
23
reserved
22
21
20
19
INTC
18
17
16
reserved
R/W
0
R/W
0
R/W
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
R/W
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R/W
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
RO
0
RO
0
RO
0
RO
0
INTB
Type
Reset
26
R/W
0
R/W
0
reserved
RO
0
INTA
Bit/Field
Name
Type
Reset
31:29
INTD
R/W
0x0
R/W
0
reserved
RO
0
Description
Interrupt Priority for Interrupt [4n+3]
This field holds a priority value, 0-7, for the interrupt with the number
[4n+3], where n is the number of the Interrupt Priority register (n=0 for
PRI0, and so on). The lower the value, the greater the priority of the
corresponding interrupt.
28:24
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23:21
INTC
R/W
0x0
Interrupt Priority for Interrupt [4n+2]
This field holds a priority value, 0-7, for the interrupt with the number
[4n+2], where n is the number of the Interrupt Priority register (n=0 for
PRI0, and so on). The lower the value, the greater the priority of the
corresponding interrupt.
20:16
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
15:13
INTB
R/W
0x0
Interrupt Priority for Interrupt [4n+1]
This field holds a priority value, 0-7, for the interrupt with the number
[4n+1], where n is the number of the Interrupt Priority register (n=0 for
PRI0, and so on). The lower the value, the greater the priority of the
corresponding interrupt.
12:8
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7:5
INTA
R/W
0x0
Interrupt Priority for Interrupt [4n]
This field holds a priority value, 0-7, for the interrupt with the number
[4n], where n is the number of the Interrupt Priority register (n=0 for
PRI0, and so on). The lower the value, the greater the priority of the
corresponding interrupt.
4:0
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
145
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 45: Interrupt 64-67 Priority (PRI16), offset 0x440
Register 46: Interrupt 68-71 Priority (PRI17), offset 0x444
Register 47: Interrupt 72-75 Priority (PRI18), offset 0x448
Register 48: Interrupt 76-79 Priority (PRI19), offset 0x44C
Register 49: Interrupt 80-83 Priority (PRI20), offset 0x450
Register 50: Interrupt 84-87 Priority (PRI21), offset 0x454
Register 51: Interrupt 88-91 Priority (PRI22), offset 0x458
Register 52: Interrupt 92-95 Priority (PRI23), offset 0x45C
Register 53: Interrupt 96-99 Priority (PRI24), offset 0x460
Register 54: Interrupt 100-103 Priority (PRI25), offset 0x464
Register 55: Interrupt 104-107 Priority (PRI26), offset 0x468
Register 56: Interrupt 108-111 Priority (PRI27), offset 0x46C
Register 57: Interrupt 112-115 Priority (PRI28), offset 0x470
Register 58: Interrupt 116-119 Priority (PRI29), offset 0x474
Register 59: Interrupt 120-123 Priority (PRI30), offset 0x478
Register 60: Interrupt 124-127 Priority (PRI31), offset 0x47C
Register 61: Interrupt 128-131 Priority (PRI32), offset 0x480
Register 62: Interrupt 132-135 Priority (PRI33), offset 0x484
Register 63: Interrupt 136-138 Priority (PRI34), offset 0x488
Note:
This register can only be accessed from privileged mode.
The PRIn registers (see also page 144) provide 3-bit priority fields for each interrupt. These registers
are byte accessible. Each register holds four priority fields that are assigned to interrupts as follows:
PRIn Register Bit Field
Interrupt
Bits 31:29
Interrupt [4n+3]
Bits 23:21
Interrupt [4n+2]
Bits 15:13
Interrupt [4n+1]
Bits 7:5
Interrupt [4n]
See Table 2-9 on page 96 for interrupt assignments.
Each priority level can be split into separate group priority and subpriority fields. The PRIGROUP
field in the Application Interrupt and Reset Control (APINT) register (see page 156) indicates the
position of the binary point that splits the priority and subpriority fields .
These registers can only be accessed from privileged mode.
146
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Interrupt 64-67 Priority (PRI16)
Base 0xE000.E000
Offset 0x440
Type R/W, reset 0x0000.0000
31
30
29
28
27
INTD
Type
Reset
25
24
23
reserved
22
21
20
19
INTC
18
17
16
reserved
R/W
0
R/W
0
R/W
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
R/W
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R/W
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
RO
0
RO
0
RO
0
RO
0
INTB
Type
Reset
26
R/W
0
R/W
0
reserved
RO
0
INTA
Bit/Field
Name
Type
Reset
31:29
INTD
R/W
0x0
R/W
0
reserved
RO
0
Description
Interrupt Priority for Interrupt [4n+3]
This field holds a priority value, 0-7, for the interrupt with the number
[4n+3], where n is the number of the Interrupt Priority register (n=0 for
PRI0, and so on). The lower the value, the greater the priority of the
corresponding interrupt.
28:24
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23:21
INTC
R/W
0x0
Interrupt Priority for Interrupt [4n+2]
This field holds a priority value, 0-7, for the interrupt with the number
[4n+2], where n is the number of the Interrupt Priority register (n=0 for
PRI0, and so on). The lower the value, the greater the priority of the
corresponding interrupt.
20:16
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
15:13
INTB
R/W
0x0
Interrupt Priority for Interrupt [4n+1]
This field holds a priority value, 0-7, for the interrupt with the number
[4n+1], where n is the number of the Interrupt Priority register (n=0 for
PRI0, and so on). The lower the value, the greater the priority of the
corresponding interrupt.
12:8
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7:5
INTA
R/W
0x0
Interrupt Priority for Interrupt [4n]
This field holds a priority value, 0-7, for the interrupt with the number
[4n], where n is the number of the Interrupt Priority register (n=0 for
PRI0, and so on). The lower the value, the greater the priority of the
corresponding interrupt.
4:0
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
147
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 64: Software Trigger Interrupt (SWTRIG), offset 0xF00
Note:
Only privileged software can enable unprivileged access to the SWTRIG register.
Writing an interrupt number to the SWTRIG register generates a Software Generated Interrupt (SGI).
See Table 2-9 on page 96 for interrupt assignments.
When the MAINPEND bit in the Configuration and Control (CFGCTRL) register (see page 160) is
set, unprivileged software can access the SWTRIG register.
Software Trigger Interrupt (SWTRIG)
Base 0xE000.E000
Offset 0xF00
Type WO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RO
0
WO
0
WO
0
WO
0
WO
0
WO
0
WO
0
WO
0
WO
0
reserved
Type
Reset
reserved
Type
Reset
INTID
RO
0
Bit/Field
Name
Type
Reset
31:8
reserved
RO
0x0000.00
7:0
INTID
WO
0x00
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Interrupt ID
This field holds the interrupt ID of the required SGI. For example, a value
of 0x3 generates an interrupt on IRQ3.
3.5
System Control Block (SCB) Register Descriptions
This section lists and describes the System Control Block (SCB) registers, in numerical order by
address offset. The SCB registers can only be accessed from privileged mode.
All registers must be accessed with aligned word accesses except for the FAULTSTAT and
SYSPRI1-SYSPRI3 registers, which can be accessed with byte or aligned halfword or word accesses.
The processor does not support unaligned accesses to system control block registers.
148
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 65: Auxiliary Control (ACTLR), offset 0x008
Note:
This register can only be accessed from privileged mode.
The ACTLR register provides disable bits for IT folding, write buffer use for accesses to the default
memory map, and interruption of multi-cycle instructions. By default, this register is set to provide
optimum performance from the Cortex-M4 processor and does not normally require modification.
Auxiliary Control (ACTLR)
Base 0xE000.E000
Offset 0x008
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
DISOOFP DISFPCA
RO
0
RO
0
R/W
0
R/W
0
reserved
RO
0
RO
0
RO
0
DISFOLD DISWBUF DISMCYC
RO
0
RO
0
R/W
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:10
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
9
DISOOFP
R/W
0
Disable Out-Of-Order Floating Point
Disables floating-point instructions completing out of order with respect
to integer instructions.
8
DISFPCA
R/W
0
Disable CONTROL.FPCA
Disable automatic update of the FPCA bit in the CONTROL register.
Important:
7:3
reserved
RO
0x00
2
DISFOLD
R/W
0
Two bits control when FPCA can be enabled: the ASPEN
bit in the Floating-Point Context Control (FPCC)
register and the DISFPCA bit in the Auxiliary Control
(ACTLR) register.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Disable IT Folding
Value Description
0
No effect.
1
Disables IT folding.
In some situations, the processor can start executing the first instruction
in an IT block while it is still executing the IT instruction. This behavior
is called IT folding, and improves performance, However, IT folding can
cause jitter in looping. If a task must avoid jitter, set the DISFOLD bit
before executing the task, to disable IT folding.
July 17, 2013
149
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
1
DISWBUF
R/W
0
Description
Disable Write Buffer
Value Description
0
No effect.
1
Disables write buffer use during default memory map accesses.
In this situation, all bus faults are precise bus faults but
performance is decreased because any store to memory must
complete before the processor can execute the next instruction.
Note:
0
DISMCYC
R/W
0
This bit only affects write buffers implemented in the
Cortex-M4 processor.
Disable Interrupts of Multiple Cycle Instructions
Value Description
0
No effect.
1
Disables interruption of load multiple and store multiple
instructions. In this situation, the interrupt latency of the
processor is increased because any LDM or STM must complete
before the processor can stack the current state and enter the
interrupt handler.
150
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 66: CPU ID Base (CPUID), offset 0xD00
Note:
This register can only be accessed from privileged mode.
The CPUID register contains the ARM® Cortex™-M4 processor part number, version, and
implementation information.
CPU ID Base (CPUID)
Base 0xE000.E000
Offset 0xD00
Type RO, reset 0x410F.C241
31
30
29
28
27
26
25
24
23
22
IMP
Type
Reset
21
20
19
18
VAR
RO
0
RO
1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
15
14
13
12
11
10
9
8
7
6
5
4
3
2
PARTNO
Type
Reset
RO
1
RO
1
RO
0
RO
0
RO
0
RO
0
RO
1
17
16
RO
1
RO
1
1
0
RO
0
RO
1
CON
REV
RO
0
RO
0
RO
1
Bit/Field
Name
Type
Reset
Description
31:24
IMP
RO
0x41
Implementer Code
RO
0
RO
0
RO
0
RO
0
Value Description
0x41 ARM
23:20
VAR
RO
0x0
Variant Number
Value Description
0x0
19:16
CON
RO
0xF
The rn value in the rnpn product revision identifier, for example,
the 0 in r0p0.
Constant
Value Description
0xF
15:4
PARTNO
RO
0xC24
Always reads as 0xF.
Part Number
Value Description
0xC24 Cortex-M4 processor.
3:0
REV
RO
0x1
Revision Number
Value Description
0x1
The pn value in the rnpn product revision identifier, for example,
the 1 in r0p1.
July 17, 2013
151
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 67: Interrupt Control and State (INTCTRL), offset 0xD04
Note:
This register can only be accessed from privileged mode.
The INCTRL register provides a set-pending bit for the NMI exception, and set-pending and
clear-pending bits for the PendSV and SysTick exceptions. In addition, bits in this register indicate
the exception number of the exception being processed, whether there are preempted active
exceptions, the exception number of the highest priority pending exception, and whether any interrupts
are pending.
When writing to INCTRL, the effect is unpredictable when writing a 1 to both the PENDSV and
UNPENDSV bits, or writing a 1 to both the PENDSTSET and PENDSTCLR bits.
Interrupt Control and State (INTCTRL)
Base 0xE000.E000
Offset 0xD04
Type R/W, reset 0x0000.0000
31
NMISET
Type
Reset
30
29
reserved
28
26
PENDSV UNPENDSV
25
PENDSTSET PENDSTCLR
24
reserved
23
22
21
ISRPRE ISRPEND
20
19
18
reserved
17
16
VECPEND
R/W
0
RO
0
RO
0
R/W
0
WO
0
R/W
0
WO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
VECPEND
Type
Reset
27
RO
0
RETBASE
RO
0
reserved
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31
NMISET
R/W
0
VECACT
Description
NMI Set Pending
Value Description
0
On a read, indicates an NMI exception is not pending.
On a write, no effect.
1
On a read, indicates an NMI exception is pending.
On a write, changes the NMI exception state to pending.
Because NMI is the highest-priority exception, normally the processor
enters the NMI exception handler as soon as it registers the setting of
this bit, and clears this bit on entering the interrupt handler. A read of
this bit by the NMI exception handler returns 1 only if the NMI signal is
reasserted while the processor is executing that handler.
30:29
reserved
RO
0x0
28
PENDSV
R/W
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PendSV Set Pending
Value Description
0
On a read, indicates a PendSV exception is not pending.
On a write, no effect.
1
On a read, indicates a PendSV exception is pending.
On a write, changes the PendSV exception state to pending.
Setting this bit is the only way to set the PendSV exception state to
pending. This bit is cleared by writing a 1 to the UNPENDSV bit.
152
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
27
UNPENDSV
WO
0
Description
PendSV Clear Pending
Value Description
0
On a write, no effect.
1
On a write, removes the pending state from the PendSV
exception.
This bit is write only; on a register read, its value is unknown.
26
PENDSTSET
R/W
0
SysTick Set Pending
Value Description
0
On a read, indicates a SysTick exception is not pending.
On a write, no effect.
1
On a read, indicates a SysTick exception is pending.
On a write, changes the SysTick exception state to pending.
This bit is cleared by writing a 1 to the PENDSTCLR bit.
25
PENDSTCLR
WO
0
SysTick Clear Pending
Value Description
0
On a write, no effect.
1
On a write, removes the pending state from the SysTick
exception.
This bit is write only; on a register read, its value is unknown.
24
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23
ISRPRE
RO
0
Debug Interrupt Handling
Value Description
0
The release from halt does not take an interrupt.
1
The release from halt takes an interrupt.
This bit is only meaningful in Debug mode and reads as zero when the
processor is not in Debug mode.
22
ISRPEND
RO
0
Interrupt Pending
Value Description
0
No interrupt is pending.
1
An interrupt is pending.
This bit provides status for all interrupts excluding NMI and Faults.
21:20
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
153
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
Description
19:12
VECPEND
RO
0x00
Interrupt Pending Vector Number
This field contains the exception number of the highest priority pending
enabled exception. The value indicated by this field includes the effect
of the BASEPRI and FAULTMASK registers, but not any effect of the
PRIMASK register.
Value
Description
0x00
No exceptions are pending
0x01
Reserved
0x02
NMI
0x03
Hard fault
0x04
Memory management fault
0x05
Bus fault
0x06
Usage fault
0x07-0x0A Reserved
11
RETBASE
RO
0
0x0B
SVCall
0x0C
Reserved for Debug
0x0D
Reserved
0x0E
PendSV
0x0F
SysTick
0x10
Interrupt Vector 0
0x11
Interrupt Vector 1
...
...
0x9A
Interrupt Vector 138
Return to Base
Value Description
0
There are preempted active exceptions to execute.
1
There are no active exceptions, or the currently executing
exception is the only active exception.
This bit provides status for all interrupts excluding NMI and Faults. This
bit only has meaning if the processor is currently executing an ISR (the
Interrupt Program Status (IPSR) register is non-zero).
10:8
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7:0
VECACT
RO
0x00
Interrupt Pending Vector Number
This field contains the active exception number. The exception numbers
can be found in the description for the VECPEND field. If this field is clear,
the processor is in Thread mode. This field contains the same value as
the ISRNUM field in the IPSR register.
Subtract 16 from this value to obtain the IRQ number required to index
into the Interrupt Set Enable (ENn), Interrupt Clear Enable (DISn),
Interrupt Set Pending (PENDn), Interrupt Clear Pending (UNPENDn),
and Interrupt Priority (PRIn) registers (see page 73).
154
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 68: Vector Table Offset (VTABLE), offset 0xD08
Note:
This register can only be accessed from privileged mode.
The VTABLE register indicates the offset of the vector table base address from memory address
0x0000.0000.
Vector Table Offset (VTABLE)
Base 0xE000.E000
Offset 0xD08
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
OFFSET
Type
Reset
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
OFFSET
Type
Reset
R/W
0
R/W
0
R/W
0
R/W
0
reserved
R/W
0
R/W
0
RO
0
Bit/Field
Name
Type
Reset
31:10
OFFSET
R/W
0x000.00
RO
0
RO
0
RO
0
RO
0
Description
Vector Table Offset
When configuring the OFFSET field, the offset must be aligned to the
number of exception entries in the vector table. Because there are 138
interrupts, the offset must be aligned on a 1024-byte boundary.
9:0
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
155
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 69: Application Interrupt and Reset Control (APINT), offset 0xD0C
Note:
This register can only be accessed from privileged mode.
The APINT register provides priority grouping control for the exception model, endian status for
data accesses, and reset control of the system. To write to this register, 0x05FA must be written to
the VECTKEY field, otherwise the write is ignored.
The PRIGROUP field indicates the position of the binary point that splits the INTx fields in the
Interrupt Priority (PRIx) registers into separate group priority and subpriority fields. Table
3-9 on page 156 shows how the PRIGROUP value controls this split. The bit numbers in the Group
Priority Field and Subpriority Field columns in the table refer to the bits in the INTA field. For the
INTB field, the corresponding bits are 15:13; for INTC, 23:21; and for INTD, 31:29.
Note:
Determining preemption of an exception uses only the group priority field.
Table 3-9. Interrupt Priority Levels
a
PRIGROUP Bit Field
Binary Point
Group Priority Field Subpriority Field
Group
Priorities
Subpriorities
0x0 - 0x4
bxxx.
[7:5]
None
8
1
0x5
bxx.y
[7:6]
[5]
4
2
0x6
bx.yy
[7]
[6:5]
2
4
0x7
b.yyy
None
[7:5]
1
8
a. INTx field showing the binary point. An x denotes a group priority field bit, and a y denotes a subpriority field bit.
Application Interrupt and Reset Control (APINT)
Base 0xE000.E000
Offset 0xD0C
Type R/W, reset 0xFA05.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R/W
0
R/W
0
R/W
0
R/W
1
R/W
0
R/W
1
5
4
3
2
1
0
VECTKEY
Type
Reset
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
0
15
14
13
12
11
10
reserved
ENDIANESS
Type
Reset
RO
0
RO
0
RO
0
RO
0
R/W
1
R/W
0
R/W
0
R/W
0
9
8
7
6
PRIGROUP
RO
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
31:16
VECTKEY
R/W
0xFA05
reserved
R/W
0
RO
0
RO
0
RO
0
SYSRESREQ VECTCLRACT VECTRESET
RO
0
RO
0
WO
0
WO
0
WO
0
Description
Register Key
This field is used to guard against accidental writes to this register.
0x05FA must be written to this field in order to change the bits in this
register. On a read, 0xFA05 is returned.
15
ENDIANESS
RO
0
Data Endianess
The Tiva™ C Series implementation uses only little-endian mode so
this is cleared to 0.
14:11
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
156
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
10:8
PRIGROUP
R/W
0x0
Description
Interrupt Priority Grouping
This field determines the split of group priority from subpriority (see
Table 3-9 on page 156 for more information).
7:3
reserved
RO
0x0
2
SYSRESREQ
WO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
System Reset Request
Value Description
0
No effect.
1
Resets the core and all on-chip peripherals except the Debug
interface.
This bit is automatically cleared during the reset of the core and reads
as 0.
1
VECTCLRACT
WO
0
Clear Active NMI / Fault
This bit is reserved for Debug use and reads as 0. This bit must be
written as a 0, otherwise behavior is unpredictable.
0
VECTRESET
WO
0
System Reset
This bit is reserved for Debug use and reads as 0. This bit must be
written as a 0, otherwise behavior is unpredictable.
July 17, 2013
157
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 70: System Control (SYSCTRL), offset 0xD10
Note:
This register can only be accessed from privileged mode.
The SYSCTRL register controls features of entry to and exit from low-power state.
System Control (SYSCTRL)
Base 0xE000.E000
Offset 0xD10
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
10
9
8
7
6
5
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:5
reserved
RO
0x0000.00
4
SEVONPEND
R/W
0
RO
0
RO
0
RO
0
RO
0
4
3
SEVONPEND
reserved
R/W
0
RO
0
SLEEPDEEP SLEEPEXIT
R/W
0
R/W
0
0
reserved
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Wake Up on Pending
Value Description
0
Only enabled interrupts or events can wake up the processor;
disabled interrupts are excluded.
1
Enabled events and all interrupts, including disabled interrupts,
can wake up the processor.
When an event or interrupt enters the pending state, the event signal
wakes up the processor from WFE. If the processor is not waiting for an
event, the event is registered and affects the next WFE.
The processor also wakes up on execution of a SEV instruction or an
external event.
3
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
2
SLEEPDEEP
R/W
0
Deep Sleep Enable
Value Description
0
Use Sleep mode as the low power mode.
1
Use Deep-sleep mode as the low power mode.
158
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
1
SLEEPEXIT
R/W
0
Description
Sleep on ISR Exit
Value Description
0
When returning from Handler mode to Thread mode, do not
sleep when returning to Thread mode.
1
When returning from Handler mode to Thread mode, enter sleep
or deep sleep on return from an ISR.
Setting this bit enables an interrupt-driven application to avoid returning
to an empty main application.
0
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
159
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 71: Configuration and Control (CFGCTRL), offset 0xD14
Note:
This register can only be accessed from privileged mode.
The CFGCTRL register controls entry to Thread mode and enables: the handlers for NMI, hard fault
and faults escalated by the FAULTMASK register to ignore bus faults; trapping of divide by zero
and unaligned accesses; and access to the SWTRIG register by unprivileged software (see page 148).
Configuration and Control (CFGCTRL)
Base 0xE000.E000
Offset 0xD14
Type R/W, reset 0x0000.0200
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
6
5
2
1
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
reserved
STKALIGN BFHFNMIGN
RO
0
RO
0
R/W
1
Bit/Field
Name
Type
Reset
31:10
reserved
RO
0x0000.00
9
STKALIGN
R/W
1
R/W
0
RO
0
RO
0
RO
0
4
3
DIV0
UNALIGNED
R/W
0
R/W
0
reserved MAINPEND BASETHR
RO
0
R/W
0
R/W
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Stack Alignment on Exception Entry
Value Description
0
The stack is 4-byte aligned.
1
The stack is 8-byte aligned.
On exception entry, the processor uses bit 9 of the stacked PSR to
indicate the stack alignment. On return from the exception, it uses this
stacked bit to restore the correct stack alignment.
8
BFHFNMIGN
R/W
0
Ignore Bus Fault in NMI and Fault
This bit enables handlers with priority -1 or -2 to ignore data bus faults
caused by load and store instructions. The setting of this bit applies to
the hard fault, NMI, and FAULTMASK escalated handlers.
Value Description
0
Data bus faults caused by load and store instructions cause a
lock-up.
1
Handlers running at priority -1 and -2 ignore data bus faults
caused by load and store instructions.
Set this bit only when the handler and its data are in absolutely safe
memory. The normal use of this bit is to probe system devices and
bridges to detect control path problems and fix them.
7:5
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
160
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
4
DIV0
R/W
0
Description
Trap on Divide by 0
This bit enables faulting or halting when the processor executes an
SDIV or UDIV instruction with a divisor of 0.
Value Description
3
UNALIGNED
R/W
0
0
Do not trap on divide by 0. A divide by zero returns a quotient
of 0.
1
Trap on divide by 0.
Trap on Unaligned Access
Value Description
0
Do not trap on unaligned halfword and word accesses.
1
Trap on unaligned halfword and word accesses. An unaligned
access generates a usage fault.
Unaligned LDM, STM, LDRD, and STRD instructions always fault
regardless of whether UNALIGNED is set.
2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
MAINPEND
R/W
0
Allow Main Interrupt Trigger
Value Description
0
BASETHR
R/W
0
0
Disables unprivileged software access to the SWTRIG register.
1
Enables unprivileged software access to the SWTRIG register
(see page 148).
Thread State Control
Value Description
0
The processor can enter Thread mode only when no exception
is active.
1
The processor can enter Thread mode from any level under the
control of an EXC_RETURN value (see “Exception
Return” on page 102 for more information).
July 17, 2013
161
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 72: System Handler Priority 1 (SYSPRI1), offset 0xD18
Note:
This register can only be accessed from privileged mode.
The SYSPRI1 register configures the priority level, 0 to 7 of the usage fault, bus fault, and memory
management fault exception handlers. This register is byte-accessible.
System Handler Priority 1 (SYSPRI1)
Base 0xE000.E000
Offset 0xD18
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
reserved
Type
Reset
RO
0
15
RO
0
RO
0
RO
0
RO
0
14
13
12
11
BUS
Type
Reset
R/W
0
R/W
0
RO
0
RO
0
RO
0
R/W
0
10
9
8
7
reserved
R/W
0
RO
0
22
21
20
19
USAGE
RO
0
RO
0
R/W
0
R/W
0
RO
0
RO
0
6
5
4
3
MEM
RO
0
RO
0
R/W
0
R/W
0
18
17
16
RO
0
RO
0
RO
0
2
1
0
RO
0
RO
0
reserved
reserved
R/W
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:24
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23:21
USAGE
R/W
0x0
Usage Fault Priority
This field configures the priority level of the usage fault. Configurable
priority values are in the range 0-7, with lower values having higher
priority.
20:16
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
15:13
BUS
R/W
0x0
Bus Fault Priority
This field configures the priority level of the bus fault. Configurable priority
values are in the range 0-7, with lower values having higher priority.
12:8
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7:5
MEM
R/W
0x0
Memory Management Fault Priority
This field configures the priority level of the memory management fault.
Configurable priority values are in the range 0-7, with lower values
having higher priority.
4:0
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
162
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 73: System Handler Priority 2 (SYSPRI2), offset 0xD1C
Note:
This register can only be accessed from privileged mode.
The SYSPRI2 register configures the priority level, 0 to 7 of the SVCall handler. This register is
byte-accessible.
System Handler Priority 2 (SYSPRI2)
Base 0xE000.E000
Offset 0xD1C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
SVC
Type
Reset
22
21
20
19
18
17
16
reserved
R/W
0
R/W
0
R/W
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:29
SVC
R/W
0x0
RO
0
Description
SVCall Priority
This field configures the priority level of SVCall. Configurable priority
values are in the range 0-7, with lower values having higher priority.
28:0
reserved
RO
0x000.0000
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
163
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 74: System Handler Priority 3 (SYSPRI3), offset 0xD20
Note:
This register can only be accessed from privileged mode.
The SYSPRI3 register configures the priority level, 0 to 7 of the SysTick exception and PendSV
handlers. This register is byte-accessible.
System Handler Priority 3 (SYSPRI3)
Base 0xE000.E000
Offset 0xD20
Type R/W, reset 0x0000.0000
31
30
29
28
27
TICK
Type
Reset
26
25
24
23
reserved
R/W
0
R/W
0
R/W
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
15
14
13
12
11
10
9
8
7
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
22
21
20
19
PENDSV
R/W
0
R/W
0
RO
0
RO
0
6
5
4
3
DEBUG
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:29
TICK
R/W
0x0
RO
0
R/W
0
R/W
0
18
17
16
RO
0
RO
0
RO
0
2
1
0
RO
0
RO
0
reserved
reserved
R/W
0
RO
0
RO
0
RO
0
Description
SysTick Exception Priority
This field configures the priority level of the SysTick exception.
Configurable priority values are in the range 0-7, with lower values
having higher priority.
28:24
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23:21
PENDSV
R/W
0x0
PendSV Priority
This field configures the priority level of PendSV. Configurable priority
values are in the range 0-7, with lower values having higher priority.
20:8
reserved
RO
0x000
7:5
DEBUG
R/W
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Debug Priority
This field configures the priority level of Debug. Configurable priority
values are in the range 0-7, with lower values having higher priority.
4:0
reserved
RO
0x0.0000
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
164
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 75: System Handler Control and State (SYSHNDCTRL), offset 0xD24
Note:
This register can only be accessed from privileged mode.
The SYSHNDCTRL register enables the system handlers, and indicates the pending status of the
usage fault, bus fault, memory management fault, and SVC exceptions as well as the active status
of the system handlers.
If a system handler is disabled and the corresponding fault occurs, the processor treats the fault as
a hard fault.
This register can be modified to change the pending or active status of system exceptions. An OS
kernel can write to the active bits to perform a context switch that changes the current exception
type.
Caution – Software that changes the value of an active bit in this register without correct adjustment
to the stacked content can cause the processor to generate a fault exception. Ensure software that writes
to this register retains and subsequently restores the current active status.
If the value of a bit in this register must be modified after enabling the system handlers, a
read-modify-write procedure must be used to ensure that only the required bit is modified.
System Handler Control and State (SYSHNDCTRL)
Base 0xE000.E000
Offset 0xD24
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
SVC
BUSP
MEMP
USAGEP
R/W
0
R/W
0
R/W
0
R/W
0
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
USAGE
BUS
MEM
R/W
0
R/W
0
R/W
0
10
9
8
7
6
5
4
3
2
1
0
TICK
PNDSV
reserved
MON
SVCA
R/W
0
R/W
0
RO
0
R/W
0
R/W
0
USGA
reserved
BUSA
MEMA
R/W
0
RO
0
R/W
0
R/W
0
reserved
Type
Reset
Type
Reset
reserved
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:19
reserved
RO
0x000
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
18
USAGE
R/W
0
Usage Fault Enable
Value Description
17
BUS
R/W
0
0
Disables the usage fault exception.
1
Enables the usage fault exception.
Bus Fault Enable
Value Description
0
Disables the bus fault exception.
1
Enables the bus fault exception.
July 17, 2013
165
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
16
MEM
R/W
0
Description
Memory Management Fault Enable
Value Description
15
SVC
R/W
0
0
Disables the memory management fault exception.
1
Enables the memory management fault exception.
SVC Call Pending
Value Description
0
An SVC call exception is not pending.
1
An SVC call exception is pending.
This bit can be modified to change the pending status of the SVC call
exception.
14
BUSP
R/W
0
Bus Fault Pending
Value Description
0
A bus fault exception is not pending.
1
A bus fault exception is pending.
This bit can be modified to change the pending status of the bus fault
exception.
13
MEMP
R/W
0
Memory Management Fault Pending
Value Description
0
A memory management fault exception is not pending.
1
A memory management fault exception is pending.
This bit can be modified to change the pending status of the memory
management fault exception.
12
USAGEP
R/W
0
Usage Fault Pending
Value Description
0
A usage fault exception is not pending.
1
A usage fault exception is pending.
This bit can be modified to change the pending status of the usage fault
exception.
11
TICK
R/W
0
SysTick Exception Active
Value Description
0
A SysTick exception is not active.
1
A SysTick exception is active.
This bit can be modified to change the active status of the SysTick
exception, however, see the Caution above before setting this bit.
166
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
10
PNDSV
R/W
0
Description
PendSV Exception Active
Value Description
0
A PendSV exception is not active.
1
A PendSV exception is active.
This bit can be modified to change the active status of the PendSV
exception, however, see the Caution above before setting this bit.
9
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
8
MON
R/W
0
Debug Monitor Active
Value Description
7
SVCA
R/W
0
0
The Debug monitor is not active.
1
The Debug monitor is active.
SVC Call Active
Value Description
0
SVC call is not active.
1
SVC call is active.
This bit can be modified to change the active status of the SVC call
exception, however, see the Caution above before setting this bit.
6:4
reserved
RO
0x0
3
USGA
R/W
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Usage Fault Active
Value Description
0
Usage fault is not active.
1
Usage fault is active.
This bit can be modified to change the active status of the usage fault
exception, however, see the Caution above before setting this bit.
2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
BUSA
R/W
0
Bus Fault Active
Value Description
0
Bus fault is not active.
1
Bus fault is active.
This bit can be modified to change the active status of the bus fault
exception, however, see the Caution above before setting this bit.
July 17, 2013
167
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
0
MEMA
R/W
0
Description
Memory Management Fault Active
Value Description
0
Memory management fault is not active.
1
Memory management fault is active.
This bit can be modified to change the active status of the memory
management fault exception, however, see the Caution above before
setting this bit.
168
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 76: Configurable Fault Status (FAULTSTAT), offset 0xD28
Note:
This register can only be accessed from privileged mode.
The FAULTSTAT register indicates the cause of a memory management fault, bus fault, or usage
fault. Each of these functions is assigned to a subregister as follows:
■ Usage Fault Status (UFAULTSTAT), bits 31:16
■ Bus Fault Status (BFAULTSTAT), bits 15:8
■ Memory Management Fault Status (MFAULTSTAT), bits 7:0
FAULTSTAT is byte accessible. FAULTSTAT or its subregisters can be accessed as follows:
■
■
■
■
■
The complete FAULTSTAT register, with a word access to offset 0xD28
The MFAULTSTAT, with a byte access to offset 0xD28
The MFAULTSTAT and BFAULTSTAT, with a halfword access to offset 0xD28
The BFAULTSTAT, with a byte access to offset 0xD29
The UFAULTSTAT, with a halfword access to offset 0xD2A
Bits are cleared by writing a 1 to them.
In a fault handler, the true faulting address can be determined by:
1. Read and save the Memory Management Fault Address (MMADDR) or Bus Fault Address
(FAULTADDR) value.
2. Read the MMARV bit in MFAULTSTAT, or the BFARV bit in BFAULTSTAT to determine if the
MMADDR or FAULTADDR contents are valid.
Software must follow this sequence because another higher priority exception might change the
MMADDR or FAULTADDR value. For example, if a higher priority handler preempts the current
fault handler, the other fault might change the MMADDR or FAULTADDR value.
Configurable Fault Status (FAULTSTAT)
Base 0xE000.E000
Offset 0xD28
Type R/W1C, reset 0x0000.0000
31
30
29
28
27
26
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
14
13
12
15
BFARV
Type
Reset
R/W1C
0
reserved BLSPERR BSTKE
RO
0
R/W1C
0
R/W1C
0
RO
0
RO
0
25
24
DIV0
UNALIGN
R/W1C
0
R/W1C
0
23
22
21
20
reserved
RO
0
11
10
9
8
7
BUSTKE
IMPRE
PRECISE
IBUS
MMARV
R/W1C
0
R/W1C
0
R/W1C
0
R/W1C
0
R/W1C
0
RO
0
RO
0
RO
0
6
5
4
reserved MLSPERR MSTKE
RO
0
R/W1C
0
R/W1C
0
19
18
17
16
NOCP
INVPC
INVSTAT
UNDEF
R/W1C
0
R/W1C
0
R/W1C
0
R/W1C
0
3
2
MUSTKE reserved
R/W1C
0
RO
0
1
0
DERR
IERR
R/W1C
0
R/W1C
0
Bit/Field
Name
Type
Reset
Description
31:26
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
169
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
25
DIV0
R/W1C
0
Description
Divide-by-Zero Usage Fault
Value Description
0
No divide-by-zero fault has occurred, or divide-by-zero trapping
is not enabled.
1
The processor has executed an SDIV or UDIV instruction with
a divisor of 0.
When this bit is set, the PC value stacked for the exception return points
to the instruction that performed the divide by zero.
Trapping on divide-by-zero is enabled by setting the DIV0 bit in the
Configuration and Control (CFGCTRL) register (see page 160).
This bit is cleared by writing a 1 to it.
24
UNALIGN
R/W1C
0
Unaligned Access Usage Fault
Value Description
0
No unaligned access fault has occurred, or unaligned access
trapping is not enabled.
1
The processor has made an unaligned memory access.
Unaligned LDM, STM, LDRD, and STRD instructions always fault
regardless of the configuration of this bit.
Trapping on unaligned access is enabled by setting the UNALIGNED bit
in the CFGCTRL register (see page 160).
This bit is cleared by writing a 1 to it.
23:20
reserved
RO
0x00
19
NOCP
R/W1C
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
No Coprocessor Usage Fault
Value Description
0
A usage fault has not been caused by attempting to access a
coprocessor.
1
The processor has attempted to access a coprocessor.
This bit is cleared by writing a 1 to it.
18
INVPC
R/W1C
0
Invalid PC Load Usage Fault
Value Description
0
A usage fault has not been caused by attempting to load an
invalid PC value.
1
The processor has attempted an illegal load of EXC_RETURN
to the PC as a result of an invalid context or an invalid
EXC_RETURN value.
When this bit is set, the PC value stacked for the exception return points
to the instruction that tried to perform the illegal load of the PC.
This bit is cleared by writing a 1 to it.
170
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
17
INVSTAT
R/W1C
0
Description
Invalid State Usage Fault
Value Description
0
A usage fault has not been caused by an invalid state.
1
The processor has attempted to execute an instruction that
makes illegal use of the EPSR register.
When this bit is set, the PC value stacked for the exception return points
to the instruction that attempted the illegal use of the Execution
Program Status Register (EPSR) register.
This bit is not set if an undefined instruction uses the EPSR register.
This bit is cleared by writing a 1 to it.
16
UNDEF
R/W1C
0
Undefined Instruction Usage Fault
Value Description
0
A usage fault has not been caused by an undefined instruction.
1
The processor has attempted to execute an undefined
instruction.
When this bit is set, the PC value stacked for the exception return points
to the undefined instruction.
An undefined instruction is an instruction that the processor cannot
decode.
This bit is cleared by writing a 1 to it.
15
BFARV
R/W1C
0
Bus Fault Address Register Valid
Value Description
0
The value in the Bus Fault Address (FAULTADDR) register
is not a valid fault address.
1
The FAULTADDR register is holding a valid fault address.
This bit is set after a bus fault, where the address is known. Other faults
can clear this bit, such as a memory management fault occurring later.
If a bus fault occurs and is escalated to a hard fault because of priority,
the hard fault handler must clear this bit. This action prevents problems
if returning to a stacked active bus fault handler whose FAULTADDR
register value has been overwritten.
This bit is cleared by writing a 1 to it.
14
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
13
BLSPERR
R/W1C
0
Bus Fault on Floating-Point Lazy State Preservation
Value Description
0
No bus fault has occurred during floating-point lazy state
preservation.
1
A bus fault has occurred during floating-point lazy state
preservation.
This bit is cleared by writing a 1 to it.
July 17, 2013
171
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
12
BSTKE
R/W1C
0
Description
Stack Bus Fault
Value Description
0
No bus fault has occurred on stacking for exception entry.
1
Stacking for an exception entry has caused one or more bus
faults.
When this bit is set, the SP is still adjusted but the values in the context
area on the stack might be incorrect. A fault address is not written to
the FAULTADDR register.
This bit is cleared by writing a 1 to it.
11
BUSTKE
R/W1C
0
Unstack Bus Fault
Value Description
0
No bus fault has occurred on unstacking for a return from
exception.
1
Unstacking for a return from exception has caused one or more
bus faults.
This fault is chained to the handler. Thus, when this bit is set, the original
return stack is still present. The SP is not adjusted from the failing return,
a new save is not performed, and a fault address is not written to the
FAULTADDR register.
This bit is cleared by writing a 1 to it.
10
IMPRE
R/W1C
0
Imprecise Data Bus Error
Value Description
0
An imprecise data bus error has not occurred.
1
A data bus error has occurred, but the return address in the
stack frame is not related to the instruction that caused the error.
When this bit is set, a fault address is not written to the FAULTADDR
register.
This fault is asynchronous. Therefore, if the fault is detected when the
priority of the current process is higher than the bus fault priority, the
bus fault becomes pending and becomes active only when the processor
returns from all higher-priority processes. If a precise fault occurs before
the processor enters the handler for the imprecise bus fault, the handler
detects that both the IMPRE bit is set and one of the precise fault status
bits is set.
This bit is cleared by writing a 1 to it.
9
PRECISE
R/W1C
0
Precise Data Bus Error
Value Description
0
A precise data bus error has not occurred.
1
A data bus error has occurred, and the PC value stacked for
the exception return points to the instruction that caused the
fault.
When this bit is set, the fault address is written to the FAULTADDR
register.
This bit is cleared by writing a 1 to it.
172
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
8
IBUS
R/W1C
0
Description
Instruction Bus Error
Value Description
0
An instruction bus error has not occurred.
1
An instruction bus error has occurred.
The processor detects the instruction bus error on prefetching an
instruction, but sets this bit only if it attempts to issue the faulting
instruction.
When this bit is set, a fault address is not written to the FAULTADDR
register.
This bit is cleared by writing a 1 to it.
7
MMARV
R/W1C
0
Memory Management Fault Address Register Valid
Value Description
0
The value in the Memory Management Fault Address
(MMADDR) register is not a valid fault address.
1
The MMADDR register is holding a valid fault address.
If a memory management fault occurs and is escalated to a hard fault
because of priority, the hard fault handler must clear this bit. This action
prevents problems if returning to a stacked active memory management
fault handler whose MMADDR register value has been overwritten.
This bit is cleared by writing a 1 to it.
6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
MLSPERR
R/W1C
0
Memory Management Fault on Floating-Point Lazy State Preservation
Value Description
0
No memory management fault has occurred during floating-point
lazy state preservation.
1
No memory management fault has occurred during floating-point
lazy state preservation.
This bit is cleared by writing a 1 to it.
4
MSTKE
R/W1C
0
Stack Access Violation
Value Description
0
No memory management fault has occurred on stacking for
exception entry.
1
Stacking for an exception entry has caused one or more access
violations.
When this bit is set, the SP is still adjusted but the values in the context
area on the stack might be incorrect. A fault address is not written to
the MMADDR register.
This bit is cleared by writing a 1 to it.
July 17, 2013
173
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
3
MUSTKE
R/W1C
0
Description
Unstack Access Violation
Value Description
0
No memory management fault has occurred on unstacking for
a return from exception.
1
Unstacking for a return from exception has caused one or more
access violations.
This fault is chained to the handler. Thus, when this bit is set, the original
return stack is still present. The SP is not adjusted from the failing return,
a new save is not performed, and a fault address is not written to the
MMADDR register.
This bit is cleared by writing a 1 to it.
2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
DERR
R/W1C
0
Data Access Violation
Value Description
0
A data access violation has not occurred.
1
The processor attempted a load or store at a location that does
not permit the operation.
When this bit is set, the PC value stacked for the exception return points
to the faulting instruction and the address of the attempted access is
written to the MMADDR register.
This bit is cleared by writing a 1 to it.
0
IERR
R/W1C
0
Instruction Access Violation
Value Description
0
An instruction access violation has not occurred.
1
The processor attempted an instruction fetch from a location
that does not permit execution.
This fault occurs on any access to an XN region, even when the MPU
is disabled or not present.
When this bit is set, the PC value stacked for the exception return points
to the faulting instruction and the address of the attempted access is
not written to the MMADDR register.
This bit is cleared by writing a 1 to it.
174
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 77: Hard Fault Status (HFAULTSTAT), offset 0xD2C
Note:
This register can only be accessed from privileged mode.
The HFAULTSTAT register gives information about events that activate the hard fault handler.
Bits are cleared by writing a 1 to them.
Hard Fault Status (HFAULTSTAT)
Base 0xE000.E000
Offset 0xD2C
Type R/W1C, reset 0x0000.0000
Type
Reset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
DBG
FORCED
R/W1C
0
R/W1C
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
VECT
reserved
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W1C
0
RO
0
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31
DBG
R/W1C
0
Description
Debug Event
This bit is reserved for Debug use. This bit must be written as a 0,
otherwise behavior is unpredictable.
30
FORCED
R/W1C
0
Forced Hard Fault
Value Description
0
No forced hard fault has occurred.
1
A forced hard fault has been generated by escalation of a fault
with configurable priority that cannot be handled, either because
of priority or because it is disabled.
When this bit is set, the hard fault handler must read the other fault
status registers to find the cause of the fault.
This bit is cleared by writing a 1 to it.
29:2
reserved
RO
0x00
1
VECT
R/W1C
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Vector Table Read Fault
Value Description
0
No bus fault has occurred on a vector table read.
1
A bus fault occurred on a vector table read.
This error is always handled by the hard fault handler.
When this bit is set, the PC value stacked for the exception return points
to the instruction that was preempted by the exception.
This bit is cleared by writing a 1 to it.
0
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
175
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 78: Memory Management Fault Address (MMADDR), offset 0xD34
Note:
This register can only be accessed from privileged mode.
The MMADDR register contains the address of the location that generated a memory management
fault. When an unaligned access faults, the address in the MMADDR register is the actual address
that faulted. Because a single read or write instruction can be split into multiple aligned accesses,
the fault address can be any address in the range of the requested access size. Bits in the Memory
Management Fault Status (MFAULTSTAT) register indicate the cause of the fault and whether
the value in the MMADDR register is valid (see page 169).
Memory Management Fault Address (MMADDR)
Base 0xE000.E000
Offset 0xD34
Type R/W, reset 31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
7
6
5
4
3
2
1
0
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
ADDR
Type
Reset
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
15
14
13
12
11
10
9
8
ADDR
Type
Reset
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
Bit/Field
Name
Type
Reset
31:0
ADDR
R/W
-
R/W
-
Description
Fault Address
When the MMARV bit of MFAULTSTAT is set, this field holds the address
of the location that generated the memory management fault.
176
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 79: Bus Fault Address (FAULTADDR), offset 0xD38
Note:
This register can only be accessed from privileged mode.
The FAULTADDR register contains the address of the location that generated a bus fault. When
an unaligned access faults, the address in the FAULTADDR register is the one requested by the
instruction, even if it is not the address of the fault. Bits in the Bus Fault Status (BFAULTSTAT)
register indicate the cause of the fault and whether the value in the FAULTADDR register is valid
(see page 169).
Bus Fault Address (FAULTADDR)
Base 0xE000.E000
Offset 0xD38
Type R/W, reset 31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
7
6
5
4
3
2
1
0
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
ADDR
Type
Reset
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
15
14
13
12
11
10
9
8
ADDR
Type
Reset
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
Bit/Field
Name
Type
Reset
31:0
ADDR
R/W
-
R/W
-
Description
Fault Address
When the FAULTADDRV bit of BFAULTSTAT is set, this field holds the
address of the location that generated the bus fault.
3.6
Memory Protection Unit (MPU) Register Descriptions
This section lists and describes the Memory Protection Unit (MPU) registers, in numerical order by
address offset.
The MPU registers can only be accessed from privileged mode.
July 17, 2013
177
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 80: MPU Type (MPUTYPE), offset 0xD90
Note:
This register can only be accessed from privileged mode.
The MPUTYPE register indicates whether the MPU is present, and if so, how many regions it
supports.
MPU Type (MPUTYPE)
Base 0xE000.E000
Offset 0xD90
Type RO, reset 0x0000.0800
31
30
29
28
27
26
25
24
23
22
21
20
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
DREGION
Type
Reset
RO
0
RO
0
RO
0
RO
0
19
18
17
16
RO
0
IREGION
RO
0
RO
0
RO
0
RO
0
4
3
2
1
reserved
RO
1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
0
SEPARATE
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:24
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23:16
IREGION
RO
0x00
Number of I Regions
This field indicates the number of supported MPU instruction regions.
This field always contains 0x00. The MPU memory map is unified and
is described by the DREGION field.
15:8
DREGION
RO
0x08
Number of D Regions
Value Description
0x08 Indicates there are eight supported MPU data regions.
7:1
reserved
RO
0x00
0
SEPARATE
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Separate or Unified MPU
Value Description
0
Indicates the MPU is unified.
178
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 81: MPU Control (MPUCTRL), offset 0xD94
Note:
This register can only be accessed from privileged mode.
The MPUCTRL register enables the MPU, enables the default memory map background region,
and enables use of the MPU when in the hard fault, Non-maskable Interrupt (NMI), and Fault Mask
Register (FAULTMASK) escalated handlers.
When the ENABLE and PRIVDEFEN bits are both set:
■ For privileged accesses, the default memory map is as described in “Memory Model” on page 84.
Any access by privileged software that does not address an enabled memory region behaves
as defined by the default memory map.
■ Any access by unprivileged software that does not address an enabled memory region causes
a memory management fault.
Execute Never (XN) and Strongly Ordered rules always apply to the System Control Space regardless
of the value of the ENABLE bit.
When the ENABLE bit is set, at least one region of the memory map must be enabled for the system
to function unless the PRIVDEFEN bit is set. If the PRIVDEFEN bit is set and no regions are enabled,
then only privileged software can operate.
When the ENABLE bit is clear, the system uses the default memory map, which has the same
memory attributes as if the MPU is not implemented (see Table 2-5 on page 88 for more information).
The default memory map applies to accesses from both privileged and unprivileged software.
When the MPU is enabled, accesses to the System Control Space and vector table are always
permitted. Other areas are accessible based on regions and whether PRIVDEFEN is set.
Unless HFNMIENA is set, the MPU is not enabled when the processor is executing the handler for
an exception with priority –1 or –2. These priorities are only possible when handling a hard fault or
NMI exception or when FAULTMASK is enabled. Setting the HFNMIENA bit enables the MPU when
operating with these two priorities.
MPU Control (MPUCTRL)
Base 0xE000.E000
Offset 0xD94
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
31:3
reserved
RO
0x0000.000
PRIVDEFEN HFNMIENA
R/W
0
R/W
0
ENABLE
R/W
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
179
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
2
PRIVDEFEN
R/W
0
Description
MPU Default Region
This bit enables privileged software access to the default memory map.
Value Description
0
If the MPU is enabled, this bit disables use of the default memory
map. Any memory access to a location not covered by any
enabled region causes a fault.
1
If the MPU is enabled, this bit enables use of the default memory
map as a background region for privileged software accesses.
When this bit is set, the background region acts as if it is region number
-1. Any region that is defined and enabled has priority over this default
map.
If the MPU is disabled, the processor ignores this bit.
1
HFNMIENA
R/W
0
MPU Enabled During Faults
This bit controls the operation of the MPU during hard fault, NMI, and
FAULTMASK handlers.
Value Description
0
The MPU is disabled during hard fault, NMI, and FAULTMASK
handlers, regardless of the value of the ENABLE bit.
1
The MPU is enabled during hard fault, NMI, and FAULTMASK
handlers.
When the MPU is disabled and this bit is set, the resulting behavior is
unpredictable.
0
ENABLE
R/W
0
MPU Enable
Value Description
0
The MPU is disabled.
1
The MPU is enabled.
When the MPU is disabled and the HFNMIENA bit is set, the resulting
behavior is unpredictable.
180
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 82: MPU Region Number (MPUNUMBER), offset 0xD98
Note:
This register can only be accessed from privileged mode.
The MPUNUMBER register selects which memory region is referenced by the MPU Region Base
Address (MPUBASE) and MPU Region Attribute and Size (MPUATTR) registers. Normally, the
required region number should be written to this register before accessing the MPUBASE or the
MPUATTR register. However, the region number can be changed by writing to the MPUBASE
register with the VALID bit set (see page 182). This write updates the value of the REGION field.
MPU Region Number (MPUNUMBER)
Base 0xE000.E000
Offset 0xD98
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
1
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:3
reserved
RO
0x0000.000
2:0
NUMBER
R/W
0x0
NUMBER
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
R/W
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
MPU Region to Access
This field indicates the MPU region referenced by the MPUBASE and
MPUATTR registers. The MPU supports eight memory regions.
July 17, 2013
181
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 83: MPU Region Base Address (MPUBASE), offset 0xD9C
Register 84: MPU Region Base Address Alias 1 (MPUBASE1), offset 0xDA4
Register 85: MPU Region Base Address Alias 2 (MPUBASE2), offset 0xDAC
Register 86: MPU Region Base Address Alias 3 (MPUBASE3), offset 0xDB4
Note:
This register can only be accessed from privileged mode.
The MPUBASE register defines the base address of the MPU region selected by the MPU Region
Number (MPUNUMBER) register and can update the value of the MPUNUMBER register. To
change the current region number and update the MPUNUMBER register, write the MPUBASE
register with the VALID bit set.
The ADDR field is bits 31:N of the MPUBASE register. Bits (N-1):5 are reserved. The region size,
as specified by the SIZE field in the MPU Region Attribute and Size (MPUATTR) register, defines
the value of N where:
N = Log2(Region size in bytes)
If the region size is configured to 4 GB in the MPUATTR register, there is no valid ADDR field. In
this case, the region occupies the complete memory map, and the base address is 0x0000.0000.
The base address is aligned to the size of the region. For example, a 64-KB region must be aligned
on a multiple of 64 KB, for example, at 0x0001.0000 or 0x0002.0000.
MPU Region Base Address (MPUBASE)
Base 0xE000.E000
Offset 0xD9C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
VALID
reserved
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
WO
0
RO
0
ADDR
Type
Reset
ADDR
Type
Reset
R/W
0
Bit/Field
Name
Type
Reset
31:5
ADDR
R/W
0x0000.000
REGION
R/W
0
R/W
0
R/W
0
Description
Base Address Mask
Bits 31:N in this field contain the region base address. The value of N
depends on the region size, as shown above. The remaining bits (N-1):5
are reserved.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
182
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
4
VALID
WO
0
Description
Region Number Valid
Value Description
0
The MPUNUMBER register is not changed and the processor
updates the base address for the region specified in the
MPUNUMBER register and ignores the value of the REGION
field.
1
The MPUNUMBER register is updated with the value of the
REGION field and the base address is updated for the region
specified in the REGION field.
This bit is always read as 0.
3
reserved
RO
0
2:0
REGION
R/W
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Region Number
On a write, contains the value to be written to the MPUNUMBER register.
On a read, returns the current region number in the MPUNUMBER
register.
July 17, 2013
183
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 87: MPU Region Attribute and Size (MPUATTR), offset 0xDA0
Register 88: MPU Region Attribute and Size Alias 1 (MPUATTR1), offset 0xDA8
Register 89: MPU Region Attribute and Size Alias 2 (MPUATTR2), offset 0xDB0
Register 90: MPU Region Attribute and Size Alias 3 (MPUATTR3), offset 0xDB8
Note:
This register can only be accessed from privileged mode.
The MPUATTR register defines the region size and memory attributes of the MPU region specified
by the MPU Region Number (MPUNUMBER) register and enables that region and any subregions.
The MPUATTR register is accessible using word or halfword accesses with the most-significant
halfword holding the region attributes and the least-significant halfword holds the region size and
the region and subregion enable bits.
The MPU access permission attribute bits, XN, AP, TEX, S, C, and B, control access to the
corresponding memory region. If an access is made to an area of memory without the required
permissions, then the MPU generates a permission fault.
The SIZE field defines the size of the MPU memory region specified by the MPUNUMBER register
as follows:
(Region size in bytes) = 2(SIZE+1)
The smallest permitted region size is 32 bytes, corresponding to a SIZE value of 4. Table
3-10 on page 184 gives example SIZE values with the corresponding region size and value of N in
the MPU Region Base Address (MPUBASE) register.
Table 3-10. Example SIZE Field Values
a
SIZE Encoding
Region Size
Value of N
Note
00100b (0x4)
32 B
5
Minimum permitted size
01001b (0x9)
1 KB
10
-
10011b (0x13)
1 MB
20
-
11101b (0x1D)
1 GB
30
-
11111b (0x1F)
4 GB
No valid ADDR field in MPUBASE; the Maximum possible size
region occupies the complete
memory map.
a. Refers to the N parameter in the MPUBASE register (see page 182).
MPU Region Attribute and Size (MPUATTR)
Base 0xE000.E000
Offset 0xDA0
Type R/W, reset 0x0000.0000
31
30
29
28
27
reserved
Type
Reset
26
25
24
23
AP
21
reserved
20
19
18
TEX
17
16
XN
reserved
S
C
B
RO
0
RO
0
RO
0
R/W
0
RO
0
R/W
0
R/W
0
R/W
0
RO
0
RO
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
RO
0
RO
0
R/W
0
R/W
0
R/W
0
R/W
0
SRD
Type
Reset
22
reserved
SIZE
184
R/W
0
ENABLE
R/W
0
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
Description
31:29
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
28
XN
R/W
0
Instruction Access Disable
Value Description
0
Instruction fetches are enabled.
1
Instruction fetches are disabled.
27
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
26:24
AP
R/W
0
Access Privilege
For information on using this bit field, see Table 3-5 on page 121.
23:22
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
21:19
TEX
R/W
0x0
Type Extension Mask
For information on using this bit field, see Table 3-3 on page 120.
18
S
R/W
0
Shareable
For information on using this bit, see Table 3-3 on page 120.
17
C
R/W
0
Cacheable
For information on using this bit, see Table 3-3 on page 120.
16
B
R/W
0
Bufferable
For information on using this bit, see Table 3-3 on page 120.
15:8
SRD
R/W
0x00
Subregion Disable Bits
Value Description
0
The corresponding subregion is enabled.
1
The corresponding subregion is disabled.
Region sizes of 128 bytes and less do not support subregions. When
writing the attributes for such a region, configure the SRD field as 0x00.
See the section called “Subregions” on page 120 for more information.
7:6
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5:1
SIZE
R/W
0x0
Region Size Mask
The SIZE field defines the size of the MPU memory region specified by
the MPUNUMBER register. Refer to Table 3-10 on page 184 for more
information.
July 17, 2013
185
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
0
ENABLE
R/W
0
Description
Region Enable
Value Description
3.7
0
The region is disabled.
1
The region is enabled.
Floating-Point Unit (FPU) Register Descriptions
This section lists and describes the Floating-Point Unit (FPU) registers, in numerical order by address
offset.
186
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 91: Coprocessor Access Control (CPAC), offset 0xD88
The CPAC register specifies the access privileges for coprocessors.
Coprocessor Access Control (CPAC)
Base 0xE000.E000
Offset 0xD88
Type R/W, reset 0x0000.0000
31
30
29
28
RO
0
RO
0
RO
0
RO
0
15
14
13
RO
0
RO
0
RO
0
27
26
25
24
23
22
21
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
12
11
10
9
8
7
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
20
19
18
R/W
0
R/W
0
RO
0
RO
0
RO
0
RO
0
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
CP11
CP10
17
16
reserved
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:24
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23:22
CP11
R/W
0x00
CP11 Coprocessor Access Privilege
Value Description
0x0
Access Denied
Any attempted access generates a NOCP Usage Fault.
0x1
Privileged Access Only
An unprivileged access generates a NOCP fault.
0x2
Reserved
The result of any access is unpredictable.
0x3
21:20
CP10
R/W
0x00
Full Access
CP10 Coprocessor Access Privilege
Value Description
0x0
Access Denied
Any attempted access generates a NOCP Usage Fault.
0x1
Privileged Access Only
An unprivileged access generates a NOCP fault.
0x2
Reserved
The result of any access is unpredictable.
0x3
19:0
reserved
RO
0x00
Full Access
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
187
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 92: Floating-Point Context Control (FPCC), offset 0xF34
The FPCC register sets or returns FPU control data.
Floating-Point Context Control (FPCC)
Base 0xE000.E000
Offset 0xF34
Type R/W, reset 0xC000.0000
Type
Reset
31
30
29
28
27
26
25
24
23
ASPEN
LSPEN
R/W
1
R/W
1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
6
5
4
3
2
1
0
BFRDY
MMRDY
HFRDY
USER
LSPACT
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
reserved
Type
Reset
22
RO
0
MONRDY reserved
Bit/Field
Name
Type
Reset
31
ASPEN
R/W
1
R/W
0
RO
0
THREAD reserved
R/W
0
RO
0
Description
Automatic State Preservation Enable
When set, enables the use of the FRACTV bit in the CONTROL register
on execution of a floating-point instruction. This results in automatic
hardware state preservation and restoration, for floating-point context,
on exception entry and exit.
Important:
30
LSPEN
R/W
1
Two bits control when FPCA can be enabled: the ASPEN
bit in the Floating-Point Context Control (FPCC)
register and the DISFPCA bit in the Auxiliary Control
(ACTLR) register.
Lazy State Preservation Enable
When set, enables automatic lazy state preservation for floating-point
context.
29:9
reserved
RO
0x00
8
MONRDY
R/W
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Monitor Ready
When set, DebugMonitor is enabled and priority permits setting
MON_PEND when the floating-point stack frame was allocated.
7
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
6
BFRDY
R/W
0
Bus Fault Ready
When set, BusFault is enabled and priority permitted setting the BusFault
handler to the pending state when the floating-point stack frame was
allocated.
5
MMRDY
R/W
0
Memory Management Fault Ready
When set, MemManage is enabled and priority permitted setting the
MemManage handler to the pending state when the floating-point stack
frame was allocated.
188
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
4
HFRDY
R/W
0
Description
Hard Fault Ready
When set, priority permitted setting the HardFault handler to the pending
state when the floating-point stack frame was allocated.
3
THREAD
R/W
0
Thread Mode
When set, mode was Thread Mode when the floating-point stack frame
was allocated.
2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
USER
R/W
0
User Privilege Level
When set, privilege level was user when the floating-point stack frame
was allocated.
0
LSPACT
R/W
0
Lazy State Preservation Active
When set, Lazy State preservation is active. Floating-point stack frame
has been allocated but saving state to it has been deferred.
July 17, 2013
189
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 93: Floating-Point Context Address (FPCA), offset 0xF38
The FPCA register holds the location of the unpopulated floating-point register space allocated on
an exception stack frame.
Floating-Point Context Address (FPCA)
Base 0xE000.E000
Offset 0xF38
Type R/W, reset 31
30
29
28
27
26
25
24
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
15
14
13
12
11
10
9
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
23
22
21
20
19
18
17
16
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
8
7
6
5
4
3
2
1
0
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
RO
0
ADDRESS
Type
Reset
ADDRESS
Type
Reset
R/W
-
Bit/Field
Name
Type
Reset
31:3
ADDRESS
R/W
-
reserved
RO
0
RO
0
Description
Address
The location of the unpopulated floating-point register space allocated
on an exception stack frame.
2:0
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
190
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 94: Floating-Point Default Status Control (FPDSC), offset 0xF3C
The FPDSC register holds the default values for the Floating-Point Status Control (FPSC) register.
Floating-Point Default Status Control (FPDSC)
Base 0xE000.E000
Offset 0xF3C
Type R/W, reset 0x0000.0000
31
30
RO
0
RO
0
15
RO
0
29
28
27
26
AHP
DN
FZ
RO
0
RO
0
RO
0
R/W
-
R/W
-
R/W
-
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
25
24
23
22
21
20
19
R/W
-
17
16
R/W
-
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RMODE
18
reserved
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:27
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
26
AHP
R/W
-
AHP Bit Default
This bit holds the default value for the AHP bit in the FPSC register.
25
DN
R/W
-
DN Bit Default
This bit holds the default value for the DN bit in the FPSC register.
24
FZ
R/W
-
FZ Bit Default
This bit holds the default value for the FZ bit in the FPSC register.
23:22
RMODE
R/W
-
RMODE Bit Default
This bit holds the default value for the RMODE bit field in the FPSC
register.
Value Description
21:0
reserved
RO
0x00
0x0
Round to Nearest (RN) mode
0x1
Round towards Plus Infinity (RP) mode
0x2
Round towards Minus Infinity (RM) mode
0x3
Round towards Zero (RZ) mode
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
191
Texas Instruments-Production Data
JTAG Interface
4
JTAG Interface
The Joint Test Action Group (JTAG) port is an IEEE standard that defines a Test Access Port and
Boundary Scan Architecture for digital integrated circuits and provides a standardized serial interface
for controlling the associated test logic. The TAP, Instruction Register (IR), and Data Registers (DR)
can be used to test the interconnections of assembled printed circuit boards and obtain manufacturing
information on the components. The JTAG Port also provides a means of accessing and controlling
design-for-test features such as I/O pin observation and control, scan testing, and debugging.
The JTAG port is comprised of four pins: TCK, TMS, TDI, and TDO. Data is transmitted serially into
the controller on TDI and out of the controller on TDO. The interpretation of this data is dependent
on the current state of the TAP controller. For detailed information on the operation of the JTAG
port and TAP controller, please refer to the IEEE Standard 1149.1-Test Access Port and
Boundary-Scan Architecture.
The TM4C123BE6PZ JTAG controller works with the ARM JTAG controller built into the Cortex-M4F
core by multiplexing the TDO outputs from both JTAG controllers. ARM JTAG instructions select the
ARM TDO output while JTAG instructions select the TDO output. The multiplexer is controlled by the
JTAG controller, which has comprehensive programming for the ARM, Tiva™ C Series
microcontroller, and unimplemented JTAG instructions.
The TM4C123BE6PZ JTAG module has the following features:
■ IEEE 1149.1-1990 compatible Test Access Port (TAP) controller
■ Four-bit Instruction Register (IR) chain for storing JTAG instructions
■ IEEE standard instructions: BYPASS, IDCODE, SAMPLE/PRELOAD, and EXTEST
■ ARM additional instructions: APACC, DPACC and ABORT
■ Integrated ARM Serial Wire Debug (SWD)
– Serial Wire JTAG Debug Port (SWJ-DP)
– Flash Patch and Breakpoint (FPB) unit for implementing breakpoints
– Data Watchpoint and Trace (DWT) unit for implementing watchpoints, trigger resources, and
system profiling
– Instrumentation Trace Macrocell (ITM) for support of printf style debugging
– Embedded Trace Macrocell (ETM) for instruction trace capture
– Trace Port Interface Unit (TPIU) for bridging to a Trace Port Analyzer
See the ARM® Debug Interface V5 Architecture Specification for more information on the ARM
JTAG controller.
192
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
4.1
Block Diagram
Figure 4-1. JTAG Module Block Diagram
TCK
TMS
TAP Controller
TDI
Instruction Register (IR)
BYPASS Data Register
TDO
Boundary Scan Data Register
IDCODE Data Register
ABORT Data Register
DPACC Data Register
APACC Data Register
Cortex-M4F
Debug
Port
4.2
Signal Description
The following table lists the external signals of the JTAG/SWD controller and describes the function
of each. The JTAG/SWD controller signals are alternate functions for some GPIO signals, however
note that the reset state of the pins is for the JTAG/SWD function. The JTAG/SWD controller signals
are under commit protection and require a special process to be configured as GPIOs, see “Commit
Control” on page 648. The column in the table below titled "Pin Mux/Pin Assignment" lists the GPIO
pin placement for the JTAG/SWD controller signals. The AFSEL bit in the GPIO Alternate Function
Select (GPIOAFSEL) register (page 664) is set to choose the JTAG/SWD function. The number in
parentheses is the encoding that must be programmed into the PMCn field in the GPIO Port Control
(GPIOPCTL) register (page 682) to assign the JTAG/SWD controller signals to the specified GPIO
port pin. For more information on configuring GPIOs, see “General-Purpose Input/Outputs
(GPIOs)” on page 640.
Table 4-1. JTAG_SWD_SWO Signals (100LQFP)
Pin Name
Pin Number Pin Mux / Pin
Assignment
a
Pin Type
Buffer Type
Description
SWCLK
85
PC0 (1)
I
TTL
JTAG/SWD CLK.
SWDIO
84
PC1 (1)
I/O
TTL
JTAG TMS and SWDIO.
SWO
82
PC3 (1)
O
TTL
JTAG TDO and SWO.
TCK
85
PC0 (1)
I
TTL
JTAG/SWD CLK.
TDI
83
PC2 (1)
I
TTL
JTAG TDI.
TDO
82
PC3 (1)
O
TTL
JTAG TDO and SWO.
July 17, 2013
193
Texas Instruments-Production Data
JTAG Interface
Table 4-1. JTAG_SWD_SWO Signals (100LQFP) (continued)
Pin Name
Pin Number Pin Mux / Pin
Assignment
84
TMS
PC1 (1)
a
Pin Type
Buffer Type
I
TTL
Description
JTAG TMS and SWDIO.
a. The TTL designation indicates the pin has TTL-compatible voltage levels.
4.3
Functional Description
A high-level conceptual drawing of the JTAG module is shown in Figure 4-1 on page 193. The JTAG
module is composed of the Test Access Port (TAP) controller and serial shift chains with parallel
update registers. The TAP controller is a simple state machine controlled by the TCK and TMS inputs.
The current state of the TAP controller depends on the sequence of values captured on TMS at the
rising edge of TCK. The TAP controller determines when the serial shift chains capture new data,
shift data from TDI towards TDO, and update the parallel load registers. The current state of the
TAP controller also determines whether the Instruction Register (IR) chain or one of the Data Register
(DR) chains is being accessed.
The serial shift chains with parallel load registers are comprised of a single Instruction Register (IR)
chain and multiple Data Register (DR) chains. The current instruction loaded in the parallel load
register determines which DR chain is captured, shifted, or updated during the sequencing of the
TAP controller.
Some instructions, like EXTEST, operate on data currently in a DR chain and do not capture, shift,
or update any of the chains. Instructions that are not implemented decode to the BYPASS instruction
to ensure that the serial path between TDI and TDO is always connected (see Table 4-3 on page 200
for a list of implemented instructions).
See “JTAG and Boundary Scan” on page 1259 for JTAG timing diagrams.
Note:
4.3.1
Of all the possible reset sources, only Power-On reset (POR) and the assertion of the RST
input have any effect on the JTAG module. The pin configurations are reset by both the
RST input and POR, whereas the internal JTAG logic is only reset with POR. See “Reset
Sources” on page 205 for more information on reset.
JTAG Interface Pins
The JTAG interface consists of four standard pins: TCK, TMS, TDI, and TDO. These pins and their
associated state after a power-on reset or reset caused by the RST input are given in Table 4-2.
Detailed information on each pin follows.
Note:
The following pins are configured as JTAG port pins out of reset. Refer to “General-Purpose
Input/Outputs (GPIOs)” on page 640 for information on how to reprogram the configuration
of these pins.
Table 4-2. JTAG Port Pins State after Power-On Reset or RST assertion
Pin Name
Data Direction
Internal Pull-Up
Internal Pull-Down
Drive Strength
Drive Value
TCK
Input
Enabled
Disabled
N/A
N/A
TMS
Input
Enabled
Disabled
N/A
N/A
TDI
Input
Enabled
Disabled
N/A
N/A
TDO
Output
Enabled
Disabled
2-mA driver
High-Z
194
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
4.3.1.1
Test Clock Input (TCK)
The TCK pin is the clock for the JTAG module. This clock is provided so the test logic can operate
independently of any other system clocks and to ensure that multiple JTAG TAP controllers that
are daisy-chained together can synchronously communicate serial test data between components.
During normal operation, TCK is driven by a free-running clock with a nominal 50% duty cycle. When
necessary, TCK can be stopped at 0 or 1 for extended periods of time. While TCK is stopped at 0
or 1, the state of the TAP controller does not change and data in the JTAG Instruction and Data
Registers is not lost.
By default, the internal pull-up resistor on the TCK pin is enabled after reset, assuring that no clocking
occurs if the pin is not driven from an external source. The internal pull-up and pull-down resistors
can be turned off to save internal power as long as the TCK pin is constantly being driven by an
external source (see page 670 and page 672).
4.3.1.2
Test Mode Select (TMS)
The TMS pin selects the next state of the JTAG TAP controller. TMS is sampled on the rising edge
of TCK. Depending on the current TAP state and the sampled value of TMS, the next state may be
entered. Because the TMS pin is sampled on the rising edge of TCK, the IEEE Standard 1149.1
expects the value on TMS to change on the falling edge of TCK.
Holding TMS high for five consecutive TCK cycles drives the TAP controller state machine to the
Test-Logic-Reset state. When the TAP controller enters the Test-Logic-Reset state, the JTAG
module and associated registers are reset to their default values. This procedure should be performed
to initialize the JTAG controller. The JTAG Test Access Port state machine can be seen in its entirety
in Figure 4-2 on page 196.
By default, the internal pull-up resistor on the TMS pin is enabled after reset. Changes to the pull-up
resistor settings on GPIO Port C should ensure that the internal pull-up resistor remains enabled
on PC1/TMS; otherwise JTAG communication could be lost (see page 670).
4.3.1.3
Test Data Input (TDI)
The TDI pin provides a stream of serial information to the IR chain and the DR chains. TDI is
sampled on the rising edge of TCK and, depending on the current TAP state and the current
instruction, may present this data to the proper shift register chain. Because the TDI pin is sampled
on the rising edge of TCK, the IEEE Standard 1149.1 expects the value on TDI to change on the
falling edge of TCK.
By default, the internal pull-up resistor on the TDI pin is enabled after reset. Changes to the pull-up
resistor settings on GPIO Port C should ensure that the internal pull-up resistor remains enabled
on PC2/TDI; otherwise JTAG communication could be lost (see page 670).
4.3.1.4
Test Data Output (TDO)
The TDO pin provides an output stream of serial information from the IR chain or the DR chains.
The value of TDO depends on the current TAP state, the current instruction, and the data in the
chain being accessed. In order to save power when the JTAG port is not being used, the TDO pin
is placed in an inactive drive state when not actively shifting out data. Because TDO can be connected
to the TDI of another controller in a daisy-chain configuration, the IEEE Standard 1149.1 expects
the value on TDO to change on the falling edge of TCK.
By default, the internal pull-up resistor on the TDO pin is enabled after reset, assuring that the pin
remains at a constant logic level when the JTAG port is not being used. The internal pull-up and
July 17, 2013
195
Texas Instruments-Production Data
JTAG Interface
pull-down resistors can be turned off to save internal power if a High-Z output value is acceptable
during certain TAP controller states (see page 670 and page 672).
4.3.2
JTAG TAP Controller
The JTAG TAP controller state machine is shown in Figure 4-2. The TAP controller state machine
is reset to the Test-Logic-Reset state on the assertion of a Power-On-Reset (POR). In order to reset
the JTAG module after the microcontroller has been powered on, the TMS input must be held HIGH
for five TCK clock cycles, resetting the TAP controller and all associated JTAG chains. Asserting
the correct sequence on the TMS pin allows the JTAG module to shift in new instructions, shift in
data, or idle during extended testing sequences. For detailed information on the function of the TAP
controller and the operations that occur in each state, please refer to IEEE Standard 1149.1.
Figure 4-2. Test Access Port State Machine
Test Logic Reset
1
0
Run Test Idle
0
Select DR Scan
1
Select IR Scan
1
0
1
Capture DR
1
Capture IR
0
0
Shift DR
Shift IR
0
1
Exit 1 DR
Exit 1 IR
1
Pause IR
0
1
Exit 2 DR
0
1
0
Exit 2 IR
1
1
Update DR
4.3.3
1
0
Pause DR
1
0
1
0
0
1
0
0
Update IR
1
0
Shift Registers
The Shift Registers consist of a serial shift register chain and a parallel load register. The serial shift
register chain samples specific information during the TAP controller’s CAPTURE states and allows
this information to be shifted out on TDO during the TAP controller’s SHIFT states. While the sampled
data is being shifted out of the chain on TDO, new data is being shifted into the serial shift register
on TDI. This new data is stored in the parallel load register during the TAP controller’s UPDATE
states. Each of the shift registers is discussed in detail in “Register Descriptions” on page 200.
196
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
4.3.4
Operational Considerations
Certain operational parameters must be considered when using the JTAG module. Because the
JTAG pins can be programmed to be GPIOs, board configuration and reset conditions on these
pins must be considered. In addition, because the JTAG module has integrated ARM Serial Wire
Debug, the method for switching between these two operational modes is described below.
4.3.4.1
GPIO Functionality
When the microcontroller is reset with either a POR or RST, the JTAG/SWD port pins default to their
JTAG/SWD configurations. The default configuration includes enabling digital functionality (DEN[3:0]
set in the Port C GPIO Digital Enable (GPIODEN) register), enabling the pull-up resistors (PUE[3:0]
set in the Port C GPIO Pull-Up Select (GPIOPUR) register), disabling the pull-down resistors
(PDE[3:0] cleared in the Port C GPIO Pull-Down Select (GPIOPDR) register) and enabling the
alternate hardware function (AFSEL[3:0] set in the Port C GPIO Alternate Function Select
(GPIOAFSEL) register) on the JTAG/SWD pins. See page 664, page 670, page 672, and page 675.
It is possible for software to configure these pins as GPIOs after reset by clearing AFSEL[3:0] in
the Port C GPIOAFSEL register. If the user does not require the JTAG/SWD port for debugging or
board-level testing, this provides four more GPIOs for use in the design.
Caution – It is possible to create a software sequence that prevents the debugger from connecting to
the TM4C123BE6PZ microcontroller. If the program code loaded into flash immediately changes the
JTAG pins to their GPIO functionality, the debugger may not have enough time to connect and halt
the controller before the JTAG pin functionality switches. As a result, the debugger may be locked out
of the part. This issue can be avoided with a software routine that restores JTAG functionality based
on an external or software trigger. In the case that the software routine is not implemented and the
device is locked out of the part, this issue can be solved by using the TM4C123BE6PZ Flash Programmer
"Unlock" feature. Please refer to LMFLASHPROGRAMMER on the TI web for more information.
The GPIO commit control registers provide a layer of protection against accidental programming of
critical hardware peripherals. Protection is provided for the GPIO pins that can be used as the four
JTAG/SWD pins (PC[3:0])and the NMI pin (PD7 and PF0). Writes to protected bits of the GPIO
Alternate Function Select (GPIOAFSEL) register (see page 664), GPIO Pull Up Select (GPIOPUR)
register (see page 670), GPIO Pull-Down Select (GPIOPDR) register (see page 672), and GPIO
Digital Enable (GPIODEN) register (see page 675) are not committed to storage unless the GPIO
Lock (GPIOLOCK) register (see page 677) has been unlocked and the appropriate bits of the GPIO
Commit (GPIOCR) register (see page 678) have been set.
4.3.4.2
Communication with JTAG/SWD
Because the debug clock and the system clock can be running at different frequencies, care must
be taken to maintain reliable communication with the JTAG/SWD interface. In the Capture-DR state,
the result of the previous transaction, if any, is returned, together with a 3-bit ACK response. Software
should check the ACK response to see if the previous operation has completed before initiating a
new transaction. Alternatively, if the system clock is at least 8 times faster than the debug clock
(TCK or SWCLK), the previous operation has enough time to complete and the ACK bits do not have
to be checked.
4.3.4.3
Recovering a "Locked" Microcontroller
Note:
Performing the sequence below restores the non-volatile registers discussed in “Non-Volatile
Register Programming” on page 525 to their factory default values. The mass erase of the
Flash memory caused by the sequence below occurs prior to the non-volatile registers
being restored.
July 17, 2013
197
Texas Instruments-Production Data
JTAG Interface
In addition, the EEPROM is erased and its wear-leveling counters are returned to factory
default values when performing the sequence below.
If software configures any of the JTAG/SWD pins as GPIO and loses the ability to communicate
with the debugger, there is a debug port unlock sequence that can be used to recover the
microcontroller. Performing a total of ten JTAG-to-SWD and SWD-to-JTAG switch sequences while
holding the microcontroller in reset mass erases the Flash memory. The debug port unlock sequence
is:
1. Assert and hold the RST signal.
2. Apply power to the device.
3. Perform steps 1 and 2 of the JTAG-to-SWD switch sequence on the section called “JTAG-to-SWD
Switching” on page 199.
4. Perform steps 1 and 2 of the SWD-to-JTAG switch sequence on the section called “SWD-to-JTAG
Switching” on page 199.
5. Perform steps 1 and 2 of the JTAG-to-SWD switch sequence.
6. Perform steps 1 and 2 of the SWD-to-JTAG switch sequence.
7. Perform steps 1 and 2 of the JTAG-to-SWD switch sequence.
8. Perform steps 1 and 2 of the SWD-to-JTAG switch sequence.
9. Perform steps 1 and 2 of the JTAG-to-SWD switch sequence.
10. Perform steps 1 and 2 of the SWD-to-JTAG switch sequence.
11. Perform steps 1 and 2 of the JTAG-to-SWD switch sequence.
12. Perform steps 1 and 2 of the SWD-to-JTAG switch sequence.
13. Release the RST signal.
14. Wait 400 ms.
15. Power-cycle the microcontroller.
4.3.4.4
ARM Serial Wire Debug (SWD)
In order to seamlessly integrate the ARM Serial Wire Debug (SWD) functionality, a serial-wire
debugger must be able to connect to the Cortex-M4F core without having to perform, or have any
knowledge of, JTAG cycles. This integration is accomplished with a SWD preamble that is issued
before the SWD session begins.
The switching preamble used to enable the SWD interface of the SWJ-DP module starts with the
TAP controller in the Test-Logic-Reset state. From here, the preamble sequences the TAP controller
through the following states: Run Test Idle, Select DR, Select IR, Test Logic Reset, Test Logic
Reset, Run Test Idle, Run Test Idle, Select DR, Select IR, Test Logic Reset, Test Logic Reset, Run
Test Idle, Run Test Idle, Select DR, Select IR, and Test Logic Reset states.
Stepping through this sequence of the TAP state machine enables the SWD interface and disables
the JTAG interface. For more information on this operation and the SWD interface, see the ARM®
Debug Interface V5 Architecture Specification.
198
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Because this sequence is a valid series of JTAG operations that could be issued, the ARM JTAG
TAP controller is not fully compliant to the IEEE Standard 1149.1. This instance is the only one
where the ARM JTAG TAP controller does not meet full compliance with the specification. Due to
the low probability of this sequence occurring during normal operation of the TAP controller, it should
not affect normal performance of the JTAG interface.
JTAG-to-SWD Switching
To switch the operating mode of the Debug Access Port (DAP) from JTAG to SWD mode, the
external debug hardware must send the switching preamble to the microcontroller. The 16-bit
TMS/SWDIO command for switching to SWD mode is defined as b1110.0111.1001.1110, transmitted
LSB first. This command can also be represented as 0xE79E when transmitted LSB first. The
complete switch sequence should consist of the following transactions on the TCK/SWCLK and
TMS/SWDIO signals:
1. Send at least 50 TCK/SWCLK cycles with TMS/SWDIO High to ensure that both JTAG and SWD
are in their reset states.
2. Send the 16-bit JTAG-to-SWD switch command, 0xE79E, on TMS/SWDIO.
3. Send at least 50 TCK/SWCLK cycles with TMS/SWDIO High to ensure that if SWJ-DP was already
in SWD mode before sending the switch sequence, the SWD goes into the line reset state.
To verify that the Debug Access Port (DAP) has switched to the Serial Wire Debug (SWD) operating
mode, perform a SWD READID operation. The ID value can be compared against the device’s
known ID to verify the switch.
SWD-to-JTAG Switching
To switch the operating mode of the Debug Access Port (DAP) from SWD to JTAG mode, the
external debug hardware must send a switch command to the microcontroller. The 16-bit TMS/SWDIO
command for switching to JTAG mode is defined as b1110.0111.0011.1100, transmitted LSB first.
This command can also be represented as 0xE73C when transmitted LSB first. The complete switch
sequence should consist of the following transactions on the TCK/SWCLK and TMS/SWDIO signals:
1. Send at least 50 TCK/SWCLK cycles with TMS/SWDIO High to ensure that both JTAG and SWD
are in their reset states.
2. Send the 16-bit SWD-to-JTAG switch command, 0xE73C, on TMS/SWDIO.
3. Send at least 50 TCK/SWCLK cycles with TMS/SWDIO High to ensure that if SWJ-DP was already
in JTAG mode before sending the switch sequence, the JTAG goes into the Test Logic Reset
state.
To verify that the Debug Access Port (DAP) has switched to the JTAG operating mode, set the
JTAG Instruction Register (IR) to the IDCODE instruction and shift out the Data Register (DR). The
DR value can be compared against the device’s known IDCODE to verify the switch.
4.4
Initialization and Configuration
After a Power-On-Reset or an external reset (RST), the JTAG pins are automatically configured for
JTAG communication. No user-defined initialization or configuration is needed. However, if the user
application changes these pins to their GPIO function, they must be configured back to their JTAG
functionality before JTAG communication can be restored. To return the pins to their JTAG functions,
enable the four JTAG pins (PC[3:0]) for their alternate function using the GPIOAFSEL register.
July 17, 2013
199
Texas Instruments-Production Data
JTAG Interface
In addition to enabling the alternate functions, any other changes to the GPIO pad configurations
on the four JTAG pins (PC[3:0]) should be returned to their default settings.
4.5
Register Descriptions
The registers in the JTAG TAP Controller or Shift Register chains are not memory mapped and are
not accessible through the on-chip Advanced Peripheral Bus (APB). Instead, the registers within
the JTAG controller are all accessed serially through the TAP Controller. These registers include
the Instruction Register and the six Data Registers.
4.5.1
Instruction Register (IR)
The JTAG TAP Instruction Register (IR) is a four-bit serial scan chain connected between the JTAG
TDI and TDO pins with a parallel load register. When the TAP Controller is placed in the correct
states, bits can be shifted into the IR. Once these bits have been shifted into the chain and updated,
they are interpreted as the current instruction. The decode of the IR bits is shown in Table 4-3. A
detailed explanation of each instruction, along with its associated Data Register, follows.
Table 4-3. JTAG Instruction Register Commands
4.5.1.1
IR[3:0]
Instruction
0x0
EXTEST
0x2
SAMPLE / PRELOAD
Description
Drives the values preloaded into the Boundary Scan Chain by the
SAMPLE/PRELOAD instruction onto the pads.
Captures the current I/O values and shifts the sampled values out of the
Boundary Scan Chain while new preload data is shifted in.
0x8
ABORT
Shifts data into the ARM Debug Port Abort Register.
0xA
DPACC
Shifts data into and out of the ARM DP Access Register.
0xB
APACC
Shifts data into and out of the ARM AC Access Register.
0xE
IDCODE
Loads manufacturing information defined by the IEEE Standard 1149.1 into
the IDCODE chain and shifts it out.
0xF
BYPASS
Connects TDI to TDO through a single Shift Register chain.
All Others
Reserved
Defaults to the BYPASS instruction to ensure that TDI is always connected
to TDO.
EXTEST Instruction
The EXTEST instruction is not associated with its own Data Register chain. Instead, the EXTEST
instruction uses the data that has been preloaded into the Boundary Scan Data Register using the
SAMPLE/PRELOAD instruction. When the EXTEST instruction is present in the Instruction Register,
the preloaded data in the Boundary Scan Data Register associated with the outputs and output
enables are used to drive the GPIO pads rather than the signals coming from the core. With tests
that drive known values out of the controller, this instruction can be used to verify connectivity. While
the EXTEST instruction is present in the Instruction Register, the Boundary Scan Data Register can
be accessed to sample and shift out the current data and load new data into the Boundary Scan
Data Register.
4.5.1.2
SAMPLE/PRELOAD Instruction
The SAMPLE/PRELOAD instruction connects the Boundary Scan Data Register chain between
TDI and TDO. This instruction samples the current state of the pad pins for observation and preloads
new test data. Each GPIO pad has an associated input, output, and output enable signal. When the
TAP controller enters the Capture DR state during this instruction, the input, output, and output-enable
signals to each of the GPIO pads are captured. These samples are serially shifted out on TDO while
200
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
the TAP controller is in the Shift DR state and can be used for observation or comparison in various
tests.
While these samples of the inputs, outputs, and output enables are being shifted out of the Boundary
Scan Data Register, new data is being shifted into the Boundary Scan Data Register from TDI.
Once the new data has been shifted into the Boundary Scan Data Register, the data is saved in the
parallel load registers when the TAP controller enters the Update DR state. This update of the
parallel load register preloads data into the Boundary Scan Data Register that is associated with
each input, output, and output enable. This preloaded data can be used with the EXTEST instruction
to drive data into or out of the controller. See “Boundary Scan Data Register” on page 202 for more
information.
4.5.1.3
ABORT Instruction
The ABORT instruction connects the associated ABORT Data Register chain between TDI and
TDO. This instruction provides read and write access to the ABORT Register of the ARM Debug
Access Port (DAP). Shifting the proper data into this Data Register clears various error bits or initiates
a DAP abort of a previous request. See the “ABORT Data Register” on page 203 for more information.
4.5.1.4
DPACC Instruction
The DPACC instruction connects the associated DPACC Data Register chain between TDI and
TDO. This instruction provides read and write access to the DPACC Register of the ARM Debug
Access Port (DAP). Shifting the proper data into this register and reading the data output from this
register allows read and write access to the ARM debug and status registers. See “DPACC Data
Register” on page 203 for more information.
4.5.1.5
APACC Instruction
The APACC instruction connects the associated APACC Data Register chain between TDI and
TDO. This instruction provides read and write access to the APACC Register of the ARM Debug
Access Port (DAP). Shifting the proper data into this register and reading the data output from this
register allows read and write access to internal components and buses through the Debug Port.
See “APACC Data Register” on page 203 for more information.
4.5.1.6
IDCODE Instruction
The IDCODE instruction connects the associated IDCODE Data Register chain between TDI and
TDO. This instruction provides information on the manufacturer, part number, and version of the
ARM core. This information can be used by testing equipment and debuggers to automatically
configure input and output data streams. IDCODE is the default instruction loaded into the JTAG
Instruction Register when a Power-On-Reset (POR) is asserted, or the Test-Logic-Reset state is
entered. See “IDCODE Data Register” on page 202 for more information.
4.5.1.7
BYPASS Instruction
The BYPASS instruction connects the associated BYPASS Data Register chain between TDI and
TDO. This instruction is used to create a minimum length serial path between the TDI and TDO ports.
The BYPASS Data Register is a single-bit shift register. This instruction improves test efficiency by
allowing components that are not needed for a specific test to be bypassed in the JTAG scan chain
by loading them with the BYPASS instruction. See “BYPASS Data Register” on page 202 for more
information.
July 17, 2013
201
Texas Instruments-Production Data
JTAG Interface
4.5.2
Data Registers
The JTAG module contains six Data Registers. These serial Data Register chains include: IDCODE,
BYPASS, Boundary Scan, APACC, DPACC, and ABORT and are discussed in the following sections.
4.5.2.1
IDCODE Data Register
The format for the 32-bit IDCODE Data Register defined by the IEEE Standard 1149.1 is shown in
Figure 4-3. The standard requires that every JTAG-compliant microcontroller implement either the
IDCODE instruction or the BYPASS instruction as the default instruction. The LSB of the IDCODE
Data Register is defined to be a 1 to distinguish it from the BYPASS instruction, which has an LSB
of 0. This definition allows auto-configuration test tools to determine which instruction is the default
instruction.
The major uses of the JTAG port are for manufacturer testing of component assembly and program
development and debug. To facilitate the use of auto-configuration debug tools, the IDCODE
instruction outputs a value of 0x4BA0.0477. This value allows the debuggers to automatically
configure themselves to work correctly with the Cortex-M4F during debug.
Figure 4-3. IDCODE Register Format
31
TDI
4.5.2.2
28 27
12 11
Version
Part Number
1 0
Manufacturer ID
1
TDO
BYPASS Data Register
The format for the 1-bit BYPASS Data Register defined by the IEEE Standard 1149.1 is shown in
Figure 4-4. The standard requires that every JTAG-compliant microcontroller implement either the
BYPASS instruction or the IDCODE instruction as the default instruction. The LSB of the BYPASS
Data Register is defined to be a 0 to distinguish it from the IDCODE instruction, which has an LSB
of 1. This definition allows auto-configuration test tools to determine which instruction is the default
instruction.
Figure 4-4. BYPASS Register Format
0
TDI
4.5.2.3
0
TDO
Boundary Scan Data Register
The format of the Boundary Scan Data Register is shown in Figure 4-5. Each GPIO pin, starting
with a GPIO pin next to the JTAG port pins, is included in the Boundary Scan Data Register. Each
GPIO pin has three associated digital signals that are included in the chain. These signals are input,
output, and output enable, and are arranged in that order as shown in the figure.
When the Boundary Scan Data Register is accessed with the SAMPLE/PRELOAD instruction, the
input, output, and output enable from each digital pad are sampled and then shifted out of the chain
to be verified. The sampling of these values occurs on the rising edge of TCK in the Capture DR
state of the TAP controller. While the sampled data is being shifted out of the Boundary Scan chain
in the Shift DR state of the TAP controller, new data can be preloaded into the chain for use with
the EXTEST instruction. The EXTEST instruction forces data out of the controller.
202
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Figure 4-5. Boundary Scan Register Format
TDI
I
N
O
U
T
O
E
...
1st GPIO
4.5.2.4
I
N
O
U
T
mth GPIO
O
E
I
N
O
U
T
(m+1)th GPIO
O
E
...
I
N
O
U
T
O
E
TDO
GPIO nth
APACC Data Register
The format for the 35-bit APACC Data Register defined by ARM is described in the ARM® Debug
Interface V5 Architecture Specification.
4.5.2.5
DPACC Data Register
The format for the 35-bit DPACC Data Register defined by ARM is described in the ARM® Debug
Interface V5 Architecture Specification.
4.5.2.6
ABORT Data Register
The format for the 35-bit ABORT Data Register defined by ARM is described in the ARM® Debug
Interface V5 Architecture Specification.
July 17, 2013
203
Texas Instruments-Production Data
System Control
5
System Control
System control configures the overall operation of the device and provides information about the
device. Configurable features include reset control, NMI operation, power control, clock control, and
low-power modes.
5.1
Signal Description
The following table lists the external signals of the System Control module and describes the function
of each. The NMI signal is the alternate function for two GPIO signals and functions as a GPIO after
reset. PD7 and PF0 are under commit protection and require a special process to be configured as
any alternate function or to subsequently return to the GPIO function, see “Commit
Control” on page 648. The column in the table below titled "Pin Mux/Pin Assignment" lists the GPIO
pin placement for the NMI signal. The AFSEL bit in the GPIO Alternate Function Select
(GPIOAFSEL) register (page 664) should be set to choose the NMI function. The number in
parentheses is the encoding that must be programmed into the PMCn field in the GPIO Port Control
(GPIOPCTL) register (page 682) to assign the NMI signal to the specified GPIO port pin. For more
information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 640. The
remaining signals (with the word "fixed" in the Pin Mux/Pin Assignment column) have a fixed pin
assignment and function.
Table 5-1. System Control & Clocks Signals (100LQFP)
Pin Name
Pin Number Pin Mux / Pin
Assignment
a
Pin Type
Buffer Type
Description
NMI
40
100
PF0 (8)
PD7 (8)
I
TTL
Non-maskable interrupt.
OSC0
65
fixed
I
Analog
Main oscillator crystal input or an external clock
reference input.
OSC1
66
fixed
O
Analog
Main oscillator crystal output. Leave unconnected
when using a single-ended clock source.
RST
63
fixed
I
TTL
System reset input.
a. The TTL designation indicates the pin has TTL-compatible voltage levels.
5.2
Functional Description
The System Control module provides the following capabilities:
■ Device identification, see “Device Identification” on page 204
■ Local control, such as reset (see “Reset Control” on page 205), power (see “Power
Control” on page 210) and clock control (see “Clock Control” on page 211)
■ System control (Run, Sleep, and Deep-Sleep modes), see “System Control” on page 218
5.2.1
Device Identification
Several read-only registers provide software with information on the microcontroller, such as version,
part number, memory sizes, and peripherals present on the device. The Device Identification 0
(DID0) (page 229) and Device Identification 1 (DID1) (page 231) registers provide details about the
device's version, package, temperature range, and so on. The Peripheral Present registers starting
at System Control offset 0x300, such as the Watchdog Timer Peripheral Present (PPWD) register,
provide information on how many of each type of module are included on the device. Finally,
204
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
information about the capabilities of the on-chip peripherals are provided at offset 0xFC0 in each
peripheral's register space in the Peripheral Properties registers, such as the GPTM Peripheral
Properties (GPTMPP) register. Previous devices used the Device Capabilities (DC0-DC9) registers
for information about the peripherals and their capabilities. These registers are present on this device
for backward software capability, but provide no information about peripherals that were not available
on older devices.
5.2.2
Reset Control
This section discusses aspects of hardware functions during reset as well as system software
requirements following the reset sequence.
5.2.2.1
Reset Sources
The TM4C123BE6PZ microcontroller has six sources of reset:
1. Power-on reset (POR) (see page 206).
2. External reset input pin (RST) assertion (see page 207).
3. A brown-out detection that can be caused by any of the following events: (see page 208).
■ V DD under BOR0. The trigger value is the highest VDD voltage level for BOR0.
■ VDD under BOR1. The trigger value is the highest VDD voltage level for BOR1.
4. Software-initiated reset (with the software reset registers) (see page 209).
5. A watchdog timer reset condition violation (see page 209).
6. MOSC failure (see page 210).
Table 5-2 provides a summary of results of the various reset operations.
Table 5-2. Reset Sources
Core Reset?
JTAG Reset?
On-Chip Peripherals Reset?
Power-On Reset
Reset Source
Yes
Yes
Yes
RST
Yes
Pin Config Only
Yes
Brown-Out Reset
Yes
Pin Config Only
Yes
Software System Request
Reset using the SYSRESREQ
bit in the APINT register.
Yes
Pin Config Only
Yes
Software System Request
Reset using the VECTRESET
bit in the APINT register.
Yes
Pin Config Only
No
Software Peripheral Reset
No
Pin Config Only
Yes
Watchdog Reset
Yes
Pin Config Only
Yes
MOSC Failure Reset
Yes
Pin Config Only
Yes
a
a. Programmable on a module-by-module basis using the Software Reset Control Registers.
After a reset, the Reset Cause (RESC) register is set with the reset cause. The bits in this register
are sticky and maintain their state across multiple reset sequences, except when an internal POR
July 17, 2013
205
Texas Instruments-Production Data
System Control
is the cause, in which case, all the bits in the RESC register are cleared except for the POR indicator.
A bit in the RESC register can be cleared by writing a 0.
At any reset that resets the core, the user has the opportunity to direct the core to execute the ROM
Boot Loader or the application in Flash memory by using any GPIO signal as configured in the Boot
Configuration (BOOTCFG) register.
At reset, the following sequence is performed:
1. The BOOTCFG register is read. If the EN bit is clear, the ROM Boot Loader is executed.
2. In the ROM Boot Loader, the status of the specified GPIO pin is compared with the specified
polarity. If the status matches the specified polarity, the ROM is mapped to address 0x0000.0000
and execution continues out of the ROM Boot Loader.
3. f then EN bit is set or the status doesn't match the specified polarity, the data at address
0x0000.0004 is read, and if the data at this address is 0xFFFF.FFFF, the ROM is mapped to
address 0x0000.0000 and execution continues out of the ROM Boot Loader.
4. If there is data at address 0x0000.0004 that is not 0xFFFF.FFFF, the stack pointer (SP) is loaded
from Flash memory at address 0x0000.0000 and the program counter (PC) is loaded from
address 0x0000.0004. The user application begins executing.
For example, if the BOOTCFG register is written and committed with the value of 0x0000.3C01,
then PB7 is examined at reset to determine if the ROM Boot Loader should be executed. If PB7 is
Low, the core unconditionally begins executing the ROM boot loader. If PB7 is High, then the
application in Flash memory is executed if the reset vector at location 0x0000.0004 is not
0xFFFF.FFFF. Otherwise, the ROM boot loader is executed.
5.2.2.2
Power-On Reset (POR)
Note:
The JTAG controller can only be reset by the power-on reset.
The internal Power-On Reset (POR) circuit monitors the power supply voltage (VDD) and generates
a reset signal to all of the internal logic including JTAG when the power supply ramp reaches a
threshold value (VVDD_POK). The microcontroller must be operating within the specified operating
parameters when the on-chip power-on reset pulse is complete (see “Power and
Brown-Out” on page 1261). For applications that require the use of an external reset signal to hold
the microcontroller in reset longer than the internal POR, the RST input may be used as discussed
in “External RST Pin” on page 207.
The Power-On Reset sequence is as follows:
1. The microcontroller waits for internal POR to go inactive.
2. The internal reset is released and the core loads from memory the initial stack pointer, the initial
program counter, and the first instruction designated by the program counter, and then begins
execution.
The internal POR is only active on the initial power-up of the microcontroller and when the
microcontroller wakes from hibernation. The Power-On Reset timing is shown in “Power and
Brown-Out” on page 1261.
206
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
5.2.2.3
External RST Pin
Note:
It is recommended that the trace for the RST signal must be kept as short as possible. Be
sure to place any components connected to the RST signal as close to the microcontroller
as possible.
If the application only uses the internal POR circuit, the RST input must be connected to the power
supply (VDD) through an optional pull-up resistor (0 to 100K Ω) as shown in Figure 5-1 on page 207.
The RST input has filtering which requires a minimum pulse width in order for the reset pulse to be
recognized, see Table 23-11 on page 1266.
Figure 5-1. Basic RST Configuration
VDD
Tiva™
Microcontroller
RPU
RST
RPU = 0 to 100 kΩ
The external reset pin (RST) resets the microcontroller including the core and all the on-chip
peripherals. The external reset sequence is as follows:
1. The external reset pin (RST) is asserted for the duration specified by TMIN and then de-asserted
(see “Reset” on page 1266).
2. The internal reset is released and the core loads from memory the initial stack pointer, the initial
program counter, and the first instruction designated by the program counter, and then begins
execution.
To improve noise immunity and/or to delay reset at power up, the RST input may be connected to
an RC network as shown in Figure 5-2 on page 207.
Figure 5-2. External Circuitry to Extend Power-On Reset
VDD
Tiva™
Microcontroller
RPU
RST
C1
RPU = 1 kΩ to 100 kΩ
C1 = 1 nF to 10 µF
July 17, 2013
207
Texas Instruments-Production Data
System Control
If the application requires the use of an external reset switch, Figure 5-3 on page 208 shows the
proper circuitry to use.
Figure 5-3. Reset Circuit Controlled by Switch
VDD
Tiva™
Microcontroller
RPU
RST
C1
RS
Typical RPU = 10 kΩ
Typical RS = 470 Ω
C1 = 10 nF
The RPU and C1 components define the power-on delay.
The external reset timing is shown in Figure 23-11 on page 1267.
5.2.2.4
Brown-Out Reset (BOR)
The microcontroller provides a brown-out detection circuit that triggers if any of the following occur:
■ VDD under BOR0. The external VDD supply voltage is below the specified VDD BOR0 value. The
trigger value is the highest VDD voltage level for BOR0.
■ VDD under BOR1. The external VDD supply voltage is below the specified VDD BOR1 value. The
trigger value is the highest VDD voltage level for BOR1.
The application can identify that a BOR event caused a reset by reading the Reset Cause (RESC)
register. When a brown-out condition is detected, the default condition is to generate a reset. The
BOR events can also be programmed to generate an interrupt by clearing the BOR0 bit or BOR1 bit
in the Power-On and Brown-Out Reset Control (PBORCTL) register.
The brown-out reset sequence is as follows:
1. When VDD drops below VBORnTH, an internal BOR condition is set. Please refer to “Power and
Brown-Out” on page 1261 for VBORnTH value.
2. If the BOR condition exists, an internal reset is asserted.
3. The internal reset is released and the microcontroller fetches and loads the initial stack pointer,
the initial program counter, the first instruction designated by the program counter, and begins
execution.
The result of a brown-out reset is equivalent to that of an assertion of the external RST input, and
the reset is held active until the proper VDD level is restored. The RESC register can be examined
in the reset interrupt handler to determine if a Brown-Out condition was the cause of the reset, thus
allowing software to determine what actions are required to recover.
208
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
The internal Brown-Out Reset timing is shown in “Power and Brown-Out” on page 1261.
5.2.2.5
Software Reset
Software can reset a specific peripheral or generate a reset to the entire microcontroller.
Peripherals can be individually reset by software via peripheral-specific reset registers available
beginning at System Control offset 0x500 (for example the Watchdog Timer Software Reset
(SRWD) register). If the bit position corresponding to a peripheral is set and subsequently cleared,
the peripheral is reset.
The entire microcontroller, including the core, can be reset by software by setting the SYSRESREQ
bit in the Application Interrupt and Reset Control (APINT) register. The software-initiated system
reset sequence is as follows:
1. A software microcontroller reset is initiated by setting the SYSRESREQ bit.
2. An internal reset is asserted.
3. The internal reset is deasserted and the microcontroller loads from memory the initial stack
pointer, the initial program counter, and the first instruction designated by the program counter,
and then begins execution.
The core only can be reset by software by setting the VECTRESET bit in the APINT register. The
software-initiated core reset sequence is as follows:
1. A core reset is initiated by setting the VECTRESET bit.
2. An internal reset is asserted.
3. The internal reset is deasserted and the microcontroller loads from memory the initial stack
pointer, the initial program counter, and the first instruction designated by the program counter,
and then begins execution.
The software-initiated system reset timing is shown in Figure 23-12 on page 1267.
5.2.2.6
Watchdog Timer Reset
The Watchdog Timer module's function is to prevent system hangs. The TM4C123BE6PZ
microcontroller has two Watchdog Timer modules in case one watchdog clock source fails. One
watchdog is run off the system clock and the other is run off the Precision Internal Oscillator (PIOSC).
Each module operates in the same manner except that because the PIOSC watchdog timer module
is in a different clock domain, register accesses must have a time delay between them. The watchdog
timer can be configured to generate an interrupt or a non-maskable interrupt to the microcontroller
on its first time-out and to generate a reset on its second time-out.
After the watchdog's first time-out event, the 32-bit watchdog counter is reloaded with the value of
the Watchdog Timer Load (WDTLOAD) register and resumes counting down from that value. If
the timer counts down to zero again before the first time-out interrupt is cleared, and the reset signal
has been enabled, the watchdog timer asserts its reset signal to the microcontroller. The watchdog
timer reset sequence is as follows:
1. The watchdog timer times out for the second time without being serviced.
2. An internal reset is asserted.
July 17, 2013
209
Texas Instruments-Production Data
System Control
3. The internal reset is released and the microcontroller loads from memory the initial stack pointer,
the initial program counter, and the first instruction designated by the program counter, and
then begins execution.
For more information on the Watchdog Timer module, see “Watchdog Timers” on page 768.
The watchdog reset timing is shown in Figure 23-13 on page 1267.
5.2.3
Non-Maskable Interrupt
The microcontroller has four sources of non-maskable interrupt (NMI):
■ The assertion of the NMI signal
■ A main oscillator verification error
■ The NMISET bit in the Interrupt Control and State (INTCTRL) register in the Cortex™-M4F (see
page 152).
■ The Watchdog module time-out interrupt when the INTTYPE bit in the Watchdog Control
(WDTCTL) register is set (see page 774).
Software must check the cause of the interrupt in order to distinguish among the sources.
5.2.3.1
NMI Pin
The NMI signal is an alternate function for either GPIO port pin PD7 or PF0. The alternate function
must be enabled in the GPIO for the signal to be used as an interrupt, as described in
“General-Purpose Input/Outputs (GPIOs)” on page 640. Note that enabling the NMI alternate function
requires the use of the GPIO lock and commit function just like the GPIO port pins associated with
JTAG/SWD functionality, see page 678. The active sense of the NMI signal is High; asserting the
enabled NMI signal above VIH initiates the NMI interrupt sequence.
5.2.3.2
Main Oscillator Verification Failure
The TM4C123BE6PZ microcontroller provides a main oscillator verification circuit that generates
an error condition if the oscillator is running too fast or too slow. If the main oscillator verification
circuit is enabled and a failure occurs, either a power-on reset is generated and control is transferred
to the NMI handler, or an interrupt is generated. The MOSCIM bit in the MOSCCTL register determines
which action occurs. In either case, the system clock source is automatically switched to the PIOSC.
If a MOSC failure reset occurs, the NMI handler is used to address the main oscillator verification
failure because the necessary code can be removed from the general reset handler, speeding up
reset processing. The detection circuit is enabled by setting the CVAL bit in the Main Oscillator
Control (MOSCCTL) register. The main oscillator verification error is indicated in the main oscillator
fail status (MOSCFAIL) bit in the Reset Cause (RESC) register. The main oscillator verification circuit
action is described in more detail in “Main Oscillator Verification Circuit” on page 218.
5.2.4
Power Control
The TM4C123BE6PZ microcontroller provides an integrated LDO regulator that is used to provide
power to the majority of the microcontroller's internal logic. Figure 5-4 shows the power architecture.
An external LDO may not be used.
Note:
VDDA must be supplied with a voltage that meets the specification in Table 23-5 on page 1256,
or the microcontroller does not function properly. VDDA is the supply for all of the analog
circuitry on the device, including the clock circuitry.
210
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Figure 5-4. Power Architecture
VDDC
Internal
Logic and PLL
VDDC
GND
GND
LDO Voltage
Regulator
+3.3V
VDD
GND
I/O Buffers
VDD
GND
GNDA
VDDA
Analog Circuits
VDDA
5.2.5
GNDA
Clock Control
System control determines the control of clocks in this part.
5.2.5.1
Fundamental Clock Sources
There are multiple clock sources for use in the microcontroller:
■ Precision Internal Oscillator (PIOSC). The precision internal oscillator is an on-chip clock
source that is the clock source the microcontroller uses during and following POR. It does not
require the use of any external components and provides a clock that is 16 MHz ±1% at room
temperature and ±3% across temperature. The PIOSC allows for a reduced system cost in
applications that require an accurate clock source. If the main oscillator is required, software
must enable the main oscillator following reset and allow the main oscillator to stabilize before
changing the clock reference. If the Hibernation Module clock source is a 32.768-kHz oscillator,
the precision internal oscillator can be trimmed by software based on a reference clock for
increased accuracy. Regardless of whether or not the PIOSC is the source for the system clock,
the PIOSC can be configured to be the source for the ADC clock as well as the baud clock for
the UART and SSI, see “System Control” on page 218.
■ Main Oscillator (MOSC). The main oscillator provides a frequency-accurate clock source by
one of two means: an external single-ended clock source is connected to the OSC0 input pin, or
July 17, 2013
211
Texas Instruments-Production Data
System Control
an external crystal is connected across the OSC0 input and OSC1 output pins. If the PLL is being
used, the crystal value must be one of the supported frequencies between 5 MHz to 25 MHz
(inclusive). If the PLL is not being used, the crystal may be any one of the supported frequencies
between 4 MHz to 25 MHz. The single-ended clock source range is as specified in Table
23-13 on page 1269. The supported crystals are listed in the XTAL bit field in the RCC register
(see page 244).
■ Low-Frequency Internal Oscillator (LFIOSC). The low-frequency internal oscillator is intended
for use during Deep-Sleep power-saving modes. The frequency can have wide variations; refer
to “Low-Frequency Internal Oscillator (LFIOSC) Specifications” on page 1270 for more details. This
power-savings mode benefits from reduced internal switching and also allows the MOSC to be
powered down. In addition, the PIOSC can be powered down while in Deep-Sleep mode.
■ Hibernation Module Clock Source. The Hibernation module is clocked by a 32.768-kHz oscillator
connected to the XOSC0 pin. The 32.768-kHz oscillator can be used for the system clock, thus
eliminating the need for an additional crystal or oscillator. The Hibernation module clock source
is intended to provide the system with a real-time clock source and may also provide an accurate
source of Deep-Sleep or Hibernate mode power savings.
The internal system clock (SysClk), is derived from any of the above sources plus two others: the
output of the main internal PLL and the precision internal oscillator divided by four (4 MHz ± 1%).
The frequency of the PLL clock reference must be in the range of 5 MHz to 25 MHz (inclusive).
Table 5-3 on page 212 shows how the various clock sources can be used in a system.
Table 5-3. Clock Source Options
5.2.5.2
Clock Source
Drive PLL?
Precision Internal Oscillator
Yes
BYPASS = 0,
OSCSRC = 0x1
Used as SysClk?
Yes
BYPASS = 1, OSCSRC = 0x1
Precision Internal Oscillator divide by
4 (4 MHz ± 1%)
No
-
Yes
BYPASS = 1, OSCSRC = 0x2
Main Oscillator
Yes
BYPASS = 0,
OSCSRC = 0x0
Yes
BYPASS = 1, OSCSRC = 0x0
Low-Frequency Internal Oscillator
(LFIOSC)
No
-
Yes
BYPASS = 1, OSCSRC = 0x3
Hibernation Module 32.768-kHz
Oscillator
No
-
Yes
BYPASS = 1, OSCSRC2 = 0x7
Clock Configuration
The Run-Mode Clock Configuration (RCC) and Run-Mode Clock Configuration 2 (RCC2)
registers provide control for the system clock. The RCC2 register is provided to extend fields that
offer additional encodings over the RCC register. When used, the RCC2 register field values are
used by the logic over the corresponding field in the RCC register. In particular, RCC2 provides for
a larger assortment of clock configuration options. These registers control the following clock
functionality:
■ Source of clocks in sleep and deep-sleep modes
■ System clock derived from PLL or other clock source
■ Enabling/disabling of oscillators and PLL
■ Clock divisors
212
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
■ Crystal input selection
Important: Write the RCC register prior to writing the RCC2 register. If a subsequent write to the
RCC register is required, include another register access after writing the RCC register
and before writing the RCC2 register.
When transitioning the system clock configuration to use the MOSC as the fundamental
clock source, the MOSCDIS bit must be set prior to reselecting the MOSC or an undefined
system clock configuration can sporadically occur.
The configuration of the system clock must not be changed while an EEPROM operation
is in process. Software must wait until the WORKING bit in the EEPROM Done Status
(EEDONE) register is clear before making any changes to the system clock.
Figure 5-5 shows the logic for the main clock tree. The peripheral blocks are driven by the system
clock signal and can be individually enabled/disabled. The ADC clock signal can be selected from
the PIOSC, the system clock if the PLL is disabled, or the PLL output divided down to 16 MHz if the
PLL is enabled. The PWM clock signal is a synchronous divide of the system clock to provide the
PWM circuit with more range (set with PWMDIV in RCC).
Note:
If the ADC module is not using the PIOSC as the clock source, the system clock must be
at least 16 MHz.
July 17, 2013
213
Texas Instruments-Production Data
System Control
Figure 5-5. Main Clock Tree
USEPWMDIV a
PWMDW a
PWM Clock
XTALa
PWRDN b
CS f
MOSCDIS a
PLL
(400 MHz)
Main OSC
DIV400 c
BYPASS b,d
USESYSDIV a,d
UART Baud Clock
÷2
IOSCDIS a
System Clock
Precision
Internal OSC
(16 MHz)
÷ SYSDIV
÷4
e
CS f
BYPASS b,d
PWRDN
Internal OSC
(30 kHz)
SSI Baud Clock
÷ 25
Hibernation
OSC
(32.768 kHz)
OSCSRC b,d
CS f
ADC Clock
Note:
a.
b.
c.
d.
e.
f.
Control provided by RCC register bit/field.
Control provided by RCC register bit/field or RCC2 register bit/field, if overridden with RCC2 register bit
USERCC2.
Control provided by RCC2 register bit/field.
Also may be controlled by DSLPCLKCFG when in deep sleep mode.
Control provided by RCC register SYSDIV field, RCC2 register SYSDIV2 field if overridden with USERCC2
bit, or [SYSDIV2,SYSDIV2LSB] if both USERCC2 and DIV400 bits are set.
Control provided by UARTCC, SSICC, and ADCCC register field.
Communication Clock Sources
In addition to the main clock tree described above, the UART, and SSI modules all have a Clock
Control register in the peripheral's register map at offset 0xFC8 that can be used to select the clock
source for the module's baud clock. Users can choose between the system clock, which is the
default source for the baud clock, and the PIOSC. Note that there may be special considerations
when using the PIOSC as the baud clock. For more information, see the Clock Control register
description in the chapter describing the operation of the module.
Using the SYSDIV and SYSDIV2 Fields
In the RCC register, the SYSDIV field specifies which divisor is used to generate the system clock
from either the PLL output or the oscillator source (depending on how the BYPASS bit in this register
is configured). When using the PLL, the VCO frequency of 400 MHz is predivided by 2 before the
divisor is applied. Table 5-4 shows how the SYSDIV encoding affects the system clock frequency,
depending on whether the PLL is used (BYPASS=0) or another clock source is used (BYPASS=1).
214
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
The divisor is equivalent to the SYSDIV encoding plus 1. For a list of possible clock sources, see
Table 5-3 on page 212.
Table 5-4. Possible System Clock Frequencies Using the SYSDIV Field
SYSDIV
Divisor
a
Frequency (BYPASS=0) Frequency (BYPASS=1)
TivaWare™ Parameter
0x0
/1
reserved
Clock source frequency/1
SYSCTL_SYSDIV_1
0x1
/2
reserved
Clock source frequency/2
SYSCTL_SYSDIV_2
0x2
/3
66.67 MHz
Clock source frequency/3
SYSCTL_SYSDIV_3
0x3
/4
50 MHz
Clock source frequency/4
SYSCTL_SYSDIV_4
0x4
/5
40 MHz
Clock source frequency/5
SYSCTL_SYSDIV_5
0x5
/6
33.33 MHz
Clock source frequency/6
SYSCTL_SYSDIV_6
0x6
/7
28.57 MHz
Clock source frequency/7
SYSCTL_SYSDIV_7
0x7
/8
25 MHz
Clock source frequency/8
SYSCTL_SYSDIV_8
0x8
/9
22.22 MHz
Clock source frequency/9
SYSCTL_SYSDIV_9
0x9
/10
20 MHz
Clock source frequency/10
SYSCTL_SYSDIV_10
0xA
/11
18.18 MHz
Clock source frequency/11
SYSCTL_SYSDIV_11
0xB
/12
16.67 MHz
Clock source frequency/12
SYSCTL_SYSDIV_12
0xC
/13
15.38 MHz
Clock source frequency/13
SYSCTL_SYSDIV_13
0xD
/14
14.29 MHz
Clock source frequency/14
SYSCTL_SYSDIV_14
0xE
/15
13.33 MHz
Clock source frequency/15
SYSCTL_SYSDIV_15
0xF
/16
12.5 MHz (default)
Clock source frequency/16
SYSCTL_SYSDIV_16
a. This parameter is used in functions such as SysCtlClockSet() in the TivaWare Peripheral Driver Library.
The SYSDIV2 field in the RCC2 register is 2 bits wider than the SYSDIV field in the RCC register
so that additional larger divisors up to /64 are possible, allowing a lower system clock frequency for
improved Deep Sleep power consumption. When using the PLL, the VCO frequency of 400 MHz is
predivided by 2 before the divisor is applied. The divisor is equivalent to the SYSDIV2 encoding
plus 1. Table 5-5 shows how the SYSDIV2 encoding affects the system clock frequency, depending
on whether the PLL is used (BYPASS2=0) or another clock source is used (BYPASS2=1). For a list
of possible clock sources, see Table 5-3 on page 212.
Table 5-5. Examples of Possible System Clock Frequencies Using the SYSDIV2 Field
SYSDIV2
0x00
Divisor
/1
a
Frequency
(BYPASS2=0)
Frequency (BYPASS2=1)
TivaWare Parameter
reserved
Clock source frequency/1
SYSCTL_SYSDIV_1
0x01
/2
reserved
Clock source frequency/2
SYSCTL_SYSDIV_2
0x02
/3
66.67 MHz
Clock source frequency/3
SYSCTL_SYSDIV_3
0x03
/4
50 MHz
Clock source frequency/4
SYSCTL_SYSDIV_4
0x04
/5
40 MHz
Clock source frequency/5
SYSCTL_SYSDIV_5
...
...
...
...
...
0x09
/10
20 MHz
Clock source frequency/10
SYSCTL_SYSDIV_10
...
...
...
...
...
0x3F
/64
3.125 MHz
Clock source frequency/64
SYSCTL_SYSDIV_64
a. This parameter is used in functions such as SysCtlClockSet() in the TivaWare Peripheral Driver Library.
To allow for additional frequency choices when using the PLL, the DIV400 bit is provided along
with the SYSDIV2LSB bit. When the DIV400 bit is set, bit 22 becomes the LSB for SYSDIV2. In
July 17, 2013
215
Texas Instruments-Production Data
System Control
this situation, the divisor is equivalent to the (SYSDIV2 encoding with SYSDIV2LSB appended) plus
one. Table 5-6 shows the frequency choices when DIV400 is set. When the DIV400 bit is clear,
SYSDIV2LSB is ignored, and the system clock frequency is determined as shown in Table
5-5 on page 215.
Table 5-6. Examples of Possible System Clock Frequencies with DIV400=1
/2
reserved
-
0
/3
reserved
-
1
/4
reserved
-
0
/5
80 MHz
SYSCTL_SYSDIV_2_5
1
/6
66.67 MHz
SYSCTL_SYSDIV_3
0
/7
reserved
-
1
/8
50 MHz
SYSCTL_SYSDIV_4
0
/9
44.44 MHz
SYSCTL_SYSDIV_4_5
1
/10
40 MHz
SYSCTL_SYSDIV_5
...
...
...
...
0
/127
3.15 MHz
SYSCTL_SYSDIV_63_5
1
/128
3.125 MHz
SYSCTL_SYSDIV_64
0x00
reserved
0x01
0x02
0x03
0x04
...
0x3F
b
TivaWare Parameter
SYSDIV2LSB
Divisor
a
Frequency (BYPASS2=0)
SYSDIV2
a. Note that DIV400 and SYSDIV2LSB are only valid when BYPASS2=0.
b. This parameter is used in functions such as SysCtlClockSet() in the TivaWare Peripheral Driver Library.
5.2.5.3
Precision Internal Oscillator Operation (PIOSC)
The microcontroller powers up with the PIOSC running. If another clock source is desired, the PIOSC
must remain enabled as it is used for internal functions. The PIOSC can only be disabled during
Deep-Sleep mode. It can be powered down by setting the PIOSCPD bit in the DSLPCLKCFG register.
The PIOSC generates a 16-MHz clock with a ±1% accuracy at room temperatures. Across the
extended temperature range, the accuracy is ±3%. At the factory, the PIOSC is set to 16 MHz at
room temperature, however, the frequency can be trimmed for other voltage or temperature conditions
using software in one of three ways:
■ Default calibration: clear the UTEN bit and set the UPDATE bit in the Precision Internal Oscillator
Calibration (PIOSCCAL) register.
■ User-defined calibration: The user can program the UT value to adjust the PIOSC frequency. As
the UT value increases, the generated period increases. To commit a new UT value, first set the
UTEN bit, then program the UT field, and then set the UPDATE bit. The adjustment finishes within
a few clock periods and is glitch free.
■ Automatic calibration using the Hibernation module with a functioning 32.768-kHz clock source:
Set the CAL bit in the PIOSCCAL register; the results of the calibration are shown in the RESULT
field in the Precision Internal Oscillator Statistic (PIOSCSTAT) register. After calibration is
complete, the PIOSC is trimmed using the trimmed value returned in the CT field.
5.2.5.4
Crystal Configuration for the Main Oscillator (MOSC)
The main oscillator supports the use of a select number of crystals from 4 to 25 MHz.
The XTAL bit in the RCC register (see page 244) describes the available crystal choices and default
programming values.
216
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Software configures the RCC register XTAL field with the crystal number. If the PLL is used in the
design, the XTAL field value is internally translated to the PLL settings.
5.2.5.5
Main PLL Frequency Configuration
The main PLL is disabled by default during power-on reset and is enabled later by software if
required. Software specifies the output divisor to set the system clock frequency and enables the
main PLL to drive the output. The PLL operates at 400 MHz, but is divided by two prior to the
application of the output divisor, unless the DIV400 bit in the RCC2 register is set.
To configure the PIOSC to be the clock source for the main PLL, program the OSCRC2 field in the
Run-Mode Clock Configuration 2 (RCC2) register to be 0x1.
If the main oscillator provides the clock reference to the main PLL, the translation provided by
hardware and used to program the PLL is available for software in the PLL Frequency n
(PLLFREQn) registers (see page 262). The internal translation provides a translation within ± 1% of
the targeted PLL VCO frequency. Table 23-14 on page 1269 shows the actual PLL frequency and
error for a given crystal choice.
The Crystal Value field (XTAL) in the Run-Mode Clock Configuration (RCC) register (see page 244)
describes the available crystal choices and default programming of the PLLFREQn registers. Any
time the XTAL field changes, the new settings are translated and the internal PLL settings are
updated.
5.2.5.6
PLL Modes
■ Normal: The PLL multiplies the input clock reference and drives the output.
■ Power-Down: Most of the PLL internal circuitry is disabled and the PLL does not drive the output.
The modes are programmed using the RCC/RCC2 register fields (see page 244 and page 251).
5.2.5.7
PLL Operation
If a PLL configuration is changed, the PLL output frequency is unstable until it reconverges (relocks)
to the new setting. The time between the configuration change and relock is TREADY (see Table
23-13 on page 1269). During the relock time, the affected PLL is not usable as a clock reference.
Software can poll the LOCK bit in the PLL Status (PLLSTAT) register to determine when the PLL
has locked.
The PLL is changed by one of the following:
■ Change to the XTAL value in the RCC register—writes of the same value do not cause a relock.
■ Change in the PLL from Power-Down to Normal mode.
A counter clocked by the system clock is used to measure the TREADY requirement. The down
counter is set to 0x200 if the PLL is powering up. If the M or N values in the PLLFREQn registers
are changed, the counter is set to 0xC0. Hardware is provided to keep the PLL from being used as
a system clock until the TREADY condition is met after one of the two changes above. It is the user's
responsibility to have a stable clock source (like the main oscillator) before the RCC/RCC2 register
is switched to use the PLL.
If the main PLL is enabled and the system clock is switched to use the PLL in one step, the system
control hardware continues to clock the microcontroller from the oscillator selected by the RCC/RCC2
register until the main PLL is stable (TREADY time met), after which it changes to the PLL. Software
can use many methods to ensure that the system is clocked from the main PLL, including periodically
July 17, 2013
217
Texas Instruments-Production Data
System Control
polling the PLLLRIS bit in the Raw Interrupt Status (RIS) register, and enabling the PLL Lock
interrupt.
5.2.5.8
Main Oscillator Verification Circuit
The clock control includes circuitry to ensure that the main oscillator is running at the appropriate
frequency. The circuit monitors the main oscillator frequency and signals if the frequency is outside
of the allowable band of attached crystals.
The detection circuit is enabled using the CVAL bit in the Main Oscillator Control (MOSCCTL)
register. If this circuit is enabled and detects an error, and if the MOSCIM bit in the MOSCCTL register
is clear, then the following sequence is performed by the hardware:
1. The MOSCFAIL bit in the Reset Cause (RESC) register is set.
2. The system clock is switched from the main oscillator to the PIOSC.
3. An internal power-on reset is initiated.
4. Reset is de-asserted and the processor is directed to the NMI handler during the reset sequence.
if the MOSCIM bit in the MOSCCTL register is set, then the following sequence is performed by the
hardware:
1. The system clock is switched from the main oscillator to the PIOSC.
2. The MOFRIS bit in the RIS register is set to indicate a MOSC failure.
5.2.6
System Control
For power-savings purposes, the peripheral-specific RCGCx, SCGCx, and DCGCx registers (for
example, RCGCWD) control the clock gating logic for that peripheral or block in the system while
the microcontroller is in Run, Sleep, and Deep-Sleep mode, respectively. These registers are located
in the System Control register map starting at offsets 0x600, 0x700, and 0x800, respectively. There
must be a delay of 3 system clocks after a peripheral module clock is enabled in the RCGC register
before any module registers are accessed.
Important: To support legacy software, the RCGCn, SCGCn, and DCGCn registers are available
at offsets 0x100 - 0x128. A write to any of these legacy registers also writes the
corresponding bit in the peripheral-specific RCGCx, SCGCx, and DCGCx registers.
Software must use the peripheral-specific registers to support modules that are not
present in the legacy registers. It is recommended that new software use the new
registers and not rely on legacy operation.
If software uses a peripheral-specific register to write a legacy peripheral (such as
TIMER0), the write causes proper operation, but the value of that bit is not reflected in
the legacy register. Any bits that are changed by writing to a legacy register can be
read back correctly with a read of the legacy register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
There are four levels of operation for the microcontroller defined as:
■ Run mode
218
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
■ Sleep mode
■ Deep-Sleep mode
■ Hibernate mode
The following sections describe the different modes in detail.
Caution – If the Cortex-M4F Debug Access Port (DAP) has been enabled, and the device wakes from
a low power sleep or deep-sleep mode, the core may start executing code before all clocks to peripherals
have been restored to their Run mode configuration. The DAP is usually enabled by software tools
accessing the JTAG or SWD interface when debugging or flash programming. If this condition occurs,
a Hard Fault is triggered when software accesses a peripheral with an invalid clock.
A software delay loop can be used at the beginning of the interrupt routine that is used to wake up a
system from a WFI (Wait For Interrupt) instruction. This stalls the execution of any code that accesses
a peripheral register that might cause a fault. This loop can be removed for production software as the
DAP is most likely not enabled during normal execution.
Because the DAP is disabled by default (power on reset), the user can also power cycle the device. The
DAP is not enabled unless it is enabled through the JTAG or SWD interface.
5.2.6.1
Run Mode
In Run mode, the microcontroller actively executes code. Run mode provides normal operation of
the processor and all of the peripherals that are currently enabled by the the peripheral-specific
RCGC registers. The system clock can be any of the available clock sources including the PLL.
5.2.6.2
Sleep Mode
In Sleep mode, the clock frequency of the active peripherals is unchanged, but the processor and
the memory subsystem are not clocked and therefore no longer execute code. Sleep mode is entered
by the Cortex-M4F core executing a WFI (Wait for Interrupt) instruction. Any properly configured
interrupt event in the system brings the processor back into Run mode. See “Power
Management” on page 106 for more details.
Peripherals are clocked that are enabled in the peripheral-specific SCGC registers when auto-clock
gating is enabled (see the RCC register) or the the peripheral-specific RCGC registers when the
auto-clock gating is disabled. The system clock has the same source and frequency as that during
Run mode.
Additional sleep modes are available that lower the power consumption of the SRAM and Flash
memory. However, the lower power consumption modes have slower sleep and wake-up times,
see “Dynamic Power Management” on page 221 for more information.
Important: Before executing the WFI instruction, software must confirm that the EEPROM is not
busy by checking to see that the WORKING bit in the EEPROM Done Status (EEDONE)
register is clear.
5.2.6.3
Deep-Sleep Mode
In Deep-Sleep mode, the clock frequency of the active peripherals may change (depending on the
Deep-Sleep mode clock configuration) in addition to the processor clock being stopped. An interrupt
returns the microcontroller to Run mode from one of the sleep modes; the sleep modes are entered
on request from the code. Deep-Sleep mode is entered by first setting the SLEEPDEEP bit in the
System Control (SYSCTRL) register (see page 158) and then executing a WFI instruction. Any
July 17, 2013
219
Texas Instruments-Production Data
System Control
properly configured interrupt event in the system brings the processor back into Run mode. See
“Power Management” on page 106 for more details.
The Cortex-M4F processor core and the memory subsystem are not clocked in Deep-Sleep mode.
Peripherals are clocked that are enabled in the the peripheral-specific DCGC registers when
auto-clock gating is enabled (see the RCC register) or the peripheral-specific RCGC registers when
auto-clock gating is disabled. The system clock source is specified in the DSLPCLKCFG register.
When the DSLPCLKCFG register is used, the internal oscillator source is powered up, if necessary,
and other clocks are powered down. If the PLL is running at the time of the WFI instruction, hardware
powers the PLL down and overrides the SYSDIV field of the active RCC/RCC2 register, to be
determined by the DSDIVORIDE setting in the DSLPCLKCFG register, up to /16 or /64 respectively.
USB PLL is not powered down by execution of WFI instruction. When the Deep-Sleep exit event
occurs, hardware brings the system clock back to the source and frequency it had at the onset of
Deep-Sleep mode before enabling the clocks that had been stopped during the Deep-Sleep duration.
If the PIOSC is used as the PLL reference clock source, it may continue to provide the clock during
Deep-Sleep. See page 255.
Important: Before executing the WFI instruction, software must confirm that the EEPROM is not
busy by checking to see that the WORKING bit in the EEPROM Done Status (EEDONE)
register is clear.
To provide the lowest possible Deep-Sleep power consumption as well the ability to wake the
processor from a peripheral without reconfiguring the peripheral for a change in clock, some of the
communications modules have a Clock Control register at offset 0xFC8 in the module register space.
The CS field in the Clock Control register allows the user to select the PIOSC as the clock source
for the module's baud clock. When the microcontroller enters Deep-Sleep mode, the PIOSC becomes
the source for the module clock as well, which allows the transmit and receive FIFOs to continue
operation while the part is in Deep-Sleep. Figure 5-6 on page 220 shows how the clocks are selected.
Figure 5-6. Module Clock Selection
Clock Control Register
PIOSC
1
Baud Clock
0
Deep Sleep
1
Module Clock
System Clock
0
Additional deep-sleep modes are available that lower the power consumption of the SRAM and
Flash memory. However, the lower power consumption modes have slower deep-sleep and wake-up
times, see “Dynamic Power Management” on page 221 for more information.
220
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
5.2.6.4
Dynamic Power Management
In addition to the Sleep and Deep-Sleep modes and the clock gating for the on-chip modules, there
are several additional power mode options that allow the LDO, Flash memory, and SRAM into
different levels of power savings while in Sleep or Deep-Sleep modes. Note that these features may
not be available on all devices; the System Properties (SYSPROP) register provides information
on whether a mode is supported on a given MCU. The following registers provides these capabilities:
■ LDO Sleep Power Control (LDOSPCTL): controls the LDO value in Sleep mode
■ LDO Deep-Sleep Power Control (LDODPCTL): controls the LDO value in Deep-Sleep mode
■ LDO Sleep Power Calibration (LDOSPCAL): provides factory recommendations for the LDO
value in Sleep mode
■ LDO Deep-Sleep Power Calibration (LDODPCAL): provides factory recommendations for the
LDO value in Deep-Sleep mode
■ Sleep Power Configuration (SLPPWRCFG): controls the power saving modes for Flash memory
and SRAM in Sleep mode
■ Deep-Sleep Power Configuration (DSLPPWRCFG): controls the power saving modes for Flash
memory and SRAM in Deep-sleep mode
■ Deep-Sleep Clock Configuration (DSLPCLKCFG): controls the clocking in Deep-sleep mode
■ Sleep / Deep-Sleep Power Mode Status (SDPMST): provides status information on the various
power saving events
LDO Power Control
Note:
While the device is connected through JTAG, the LDO control settings for Sleep or
Deep-Sleep are not available and will not be applied.
The user can dynamically request to raise or lower the LDO voltage level to trade-off
power/performance using either the LDOSPCTL register (see page 269) or the LDODPCTL register
(see page 272). When lowering the LDO level, software must configure the system clock for the lower
LDO value in RCC/RCC2 for Sleep mode and in DSLPCLKCFG for Deep-Sleep mode before
requesting the LDO to lower.
The LDO Power Calibration registers, LDOSPCAL and LDODPCAL, provide suggested values for
the LDO in the various modes. If software requests an LDO value that is too low or too high, the
value is not accepted and an error is reported in the SDPMST register.
The table below shows the maximum system clock frequency and PIOSC frequency with respect
to the configured LDO voltage.
Operating Voltage (LDO)
Maximum System Clock Frequency
PIOSC
1.2
80 MHz
16 MHz
0.9
20 MHz
16 MHz
Flash Memory and SRAM Power Control
During Sleep or Deep-Sleep mode, Flash memory can be in either the default active mode or the
low power mode; SRAM can be in the default active mode, standby mode, or low power mode. The
active mode in each case provides the fastest times to sleep and wake up, but consumes more
July 17, 2013
221
Texas Instruments-Production Data
System Control
power. Low power mode provides the lowest power consumption, but takes longer to sleep and
wake up.
The SRAM can be programmed to prohibit any power management by configuring the SRAMSM bit
in the System Properties (SYSPROP) register. This configuration operates in the same way that
®
legacy Stellaris devices operate and provides the fastest sleep and wake-up times, but consumes
the most power while in Sleep and Deep-Sleep mode. Other power options are retention mode, and
retention mode with lower SRAM voltage. The SRAM retention mode with lower SRAM voltage
provides the lowest power consumption, but has the longest sleep and wake-up times. These modes
can be independently configured for Flash memory and SRAM using the SLPPWRCFG and
DSLPPWRCFG registers.
The following power saving options are available in Sleep and Deep-Sleep modes:
■ The clocks can be gated according to the settings in the the peripheral-specific SCGC or DCGC
registers.
■ In Deep-Sleep mode, the clock source can be changed and the PIOSC can be powered off (if
no active peripheral requires it) using the DSLPCLKCFG register. These options are not available
for Sleep mode.
■ The LDO voltage can be changed using the LDOSPCTL or LDODPCTL register.
■ The Flash memory can be put into low power mode.
■ The SRAM can be put into standby or low power mode.
The SDPMST register provides results on the Dynamic Power Management command issued. It
also has some real time status that can be viewed by a debugger or the core if it is running. These
events do not trigger an interrupt and are meant to provide information to help tune software for
power management. The status register gets written at the beginning of every Dynamic Power
Management event request that provides error checking. There is no mechanism to clear the bits;
they are overwritten on the next event. The real time data is real time and there is no event to register
that information.
5.2.6.5
Hibernate Mode
In this mode, the power supplies are turned off to the main part of the microcontroller and only the
Hibernation module's circuitry is active. An external wake event or RTC event is required to bring
the microcontroller back to Run mode. The Cortex-M4F processor and peripherals outside of the
Hibernation module see a normal "power on" sequence and the processor starts running code.
Software can determine if the microcontroller has been restarted from Hibernate mode by inspecting
the Hibernation module registers. For more information on the operation of Hibernate mode, see
“Hibernation Module” on page 486.
5.3
Initialization and Configuration
The PLL is configured using direct register writes to the RCC/RCC2 register. If the RCC2 register
is being used, the USERCC2 bit must be set and the appropriate RCC2 bit/field is used. The steps
required to successfully change the PLL-based system clock are:
1. Bypass the PLL and system clock divider by setting the BYPASS bit and clearing the USESYS
bit in the RCC register, thereby configuring the microcontroller to run off a "raw" clock source
and allowing for the new PLL configuration to be validated before switching the system clock
to the PLL.
222
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
2. Select the crystal value (XTAL) and oscillator source (OSCSRC), and clear the PWRDN bit in
RCC/RCC2. Setting the XTAL field automatically pulls valid PLL configuration data for the
appropriate crystal, and clearing the PWRDN bit powers and enables the PLL and its output.
3. Select the desired system divider (SYSDIV) in RCC/RCC2 and set the USESYS bit in RCC. The
SYSDIV field determines the system frequency for the microcontroller.
4. Wait for the PLL to lock by polling the PLLLRIS bit in the Raw Interrupt Status (RIS) register.
5. Enable use of the PLL by clearing the BYPASS bit in RCC/RCC2.
5.4
Register Map
Table 5-7 on page 223 lists the System Control registers, grouped by function. The offset listed is a
hexadecimal increment to the register's address, relative to the System Control base address of
0x400F.E000.
Note:
Spaces in the System Control register space that are not used are reserved for future or
internal use. Software should not modify any reserved memory address.
Additional Flash and ROM registers defined in the System Control register space are
described in the “Internal Memory” on page 517.
Table 5-7. System Control Register Map
Offset
Name
Type
Reset
Description
See
page
System Control Registers
0x000
DID0
RO
-
Device Identification 0
229
0x004
DID1
RO
-
Device Identification 1
231
0x030
PBORCTL
R/W
0x0000.7FFF
Brown-Out Reset Control
234
0x050
RIS
RO
0x0000.0000
Raw Interrupt Status
235
0x054
IMC
R/W
0x0000.0000
Interrupt Mask Control
237
0x058
MISC
R/W1C
0x0000.0000
Masked Interrupt Status and Clear
239
0x05C
RESC
R/W
-
Reset Cause
242
0x060
RCC
R/W
0x078E.3AD1
Run-Mode Clock Configuration
244
0x06C
GPIOHBCTL
R/W
0x0000.7E00
GPIO High-Performance Bus Control
248
0x070
RCC2
R/W
0x07C0.6810
Run-Mode Clock Configuration 2
251
0x07C
MOSCCTL
R/W
0x0000.0000
Main Oscillator Control
254
0x144
DSLPCLKCFG
R/W
0x0780.0000
Deep Sleep Clock Configuration
255
0x14C
SYSPROP
RO
0x0000.1D31
System Properties
257
0x150
PIOSCCAL
R/W
0x0000.0000
Precision Internal Oscillator Calibration
259
0x154
PIOSCSTAT
RO
0x0000.0040
Precision Internal Oscillator Statistics
261
0x160
PLLFREQ0
RO
0x0000.0032
PLL Frequency 0
262
0x164
PLLFREQ1
RO
0x0000.0001
PLL Frequency 1
263
July 17, 2013
223
Texas Instruments-Production Data
System Control
Table 5-7. System Control Register Map (continued)
Offset
Name
0x168
See
page
Type
Reset
Description
PLLSTAT
RO
0x0000.0000
PLL Status
264
0x188
SLPPWRCFG
R/W
0x0000.0000
Sleep Power Configuration
265
0x18C
DSLPPWRCFG
R/W
0x0000.0000
Deep-Sleep Power Configuration
267
0x1B4
LDOSPCTL
R/W
0x0000.0018
LDO Sleep Power Control
269
0x1B8
LDOSPCAL
RO
0x0000.1818
LDO Sleep Power Calibration
271
0x1BC
LDODPCTL
R/W
0x0000.0012
LDO Deep-Sleep Power Control
272
0x1C0
LDODPCAL
RO
0x0000.1212
LDO Deep-Sleep Power Calibration
274
0x1CC
SDPMST
RO
0x0000.0000
Sleep / Deep-Sleep Power Mode Status
275
0x300
PPWD
RO
0x0000.0003
Watchdog Timer Peripheral Present
278
0x304
PPTIMER
RO
0x0000.003F
16/32-Bit General-Purpose Timer Peripheral Present
279
0x308
PPGPIO
RO
0x0000.03FF
General-Purpose Input/Output Peripheral Present
281
0x30C
PPDMA
RO
0x0000.0001
Micro Direct Memory Access Peripheral Present
284
0x314
PPHIB
RO
0x0000.0001
Hibernation Peripheral Present
285
0x318
PPUART
RO
0x0000.00FF
Universal Asynchronous Receiver/Transmitter Peripheral
Present
286
0x31C
PPSSI
RO
0x0000.000F
Synchronous Serial Interface Peripheral Present
288
0x320
PPI2C
RO
0x0000.003F
Inter-Integrated Circuit Peripheral Present
290
0x328
PPUSB
RO
0x0000.0000
Universal Serial Bus Peripheral Present
292
0x334
PPCAN
RO
0x0000.0003
Controller Area Network Peripheral Present
293
0x338
PPADC
RO
0x0000.0003
Analog-to-Digital Converter Peripheral Present
294
0x33C
PPACMP
RO
0x0000.0001
Analog Comparator Peripheral Present
295
0x340
PPPWM
RO
0x0000.0003
Pulse Width Modulator Peripheral Present
296
0x344
PPQEI
RO
0x0000.0003
Quadrature Encoder Interface Peripheral Present
297
0x358
PPEEPROM
RO
0x0000.0001
EEPROM Peripheral Present
298
0x35C
PPWTIMER
RO
0x0000.003F
32/64-Bit Wide General-Purpose Timer Peripheral
Present
299
0x500
SRWD
R/W
0x0000.0000
Watchdog Timer Software Reset
301
0x504
SRTIMER
R/W
0x0000.0000
16/32-Bit General-Purpose Timer Software Reset
303
0x508
SRGPIO
R/W
0x0000.0000
General-Purpose Input/Output Software Reset
305
0x50C
SRDMA
R/W
0x0000.0000
Micro Direct Memory Access Software Reset
308
0x514
SRHIB
R/W
0x0000.0000
Hibernation Software Reset
309
0x518
SRUART
R/W
0x0000.0000
Universal Asynchronous Receiver/Transmitter Software
Reset
310
224
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Table 5-7. System Control Register Map (continued)
Description
See
page
Offset
Name
Type
Reset
0x51C
SRSSI
R/W
0x0000.0000
Synchronous Serial Interface Software Reset
312
0x520
SRI2C
R/W
0x0000.0000
Inter-Integrated Circuit Software Reset
314
0x534
SRCAN
R/W
0x0000.0000
Controller Area Network Software Reset
316
0x538
SRADC
R/W
0x0000.0000
Analog-to-Digital Converter Software Reset
318
0x53C
SRACMP
R/W
0x0000.0000
Analog Comparator Software Reset
320
0x540
SRPWM
R/W
0x0000.0000
Pulse Width Modulator Software Reset
321
0x544
SRQEI
R/W
0x0000.0000
Quadrature Encoder Interface Software Reset
323
0x558
SREEPROM
R/W
0x0000.0000
EEPROM Software Reset
325
0x55C
SRWTIMER
R/W
0x0000.0000
32/64-Bit Wide General-Purpose Timer Software Reset
326
0x600
RCGCWD
R/W
0x0000.0000
Watchdog Timer Run Mode Clock Gating Control
328
0x604
RCGCTIMER
R/W
0x0000.0000
16/32-Bit General-Purpose Timer Run Mode Clock Gating
Control
329
0x608
RCGCGPIO
R/W
0x0000.0000
General-Purpose Input/Output Run Mode Clock Gating
Control
331
0x60C
RCGCDMA
R/W
0x0000.0000
Micro Direct Memory Access Run Mode Clock Gating
Control
334
0x614
RCGCHIB
R/W
0x0000.0001
Hibernation Run Mode Clock Gating Control
335
0x618
RCGCUART
R/W
0x0000.0000
Universal Asynchronous Receiver/Transmitter Run Mode
Clock Gating Control
336
0x61C
RCGCSSI
R/W
0x0000.0000
Synchronous Serial Interface Run Mode Clock Gating
Control
338
0x620
RCGCI2C
R/W
0x0000.0000
Inter-Integrated Circuit Run Mode Clock Gating Control
340
0x634
RCGCCAN
R/W
0x0000.0000
Controller Area Network Run Mode Clock Gating Control
342
0x638
RCGCADC
R/W
0x0000.0000
Analog-to-Digital Converter Run Mode Clock Gating
Control
343
0x63C
RCGCACMP
R/W
0x0000.0000
Analog Comparator Run Mode Clock Gating Control
344
0x640
RCGCPWM
R/W
0x0000.0000
Pulse Width Modulator Run Mode Clock Gating Control
345
0x644
RCGCQEI
R/W
0x0000.0000
Quadrature Encoder Interface Run Mode Clock Gating
Control
346
0x658
RCGCEEPROM
R/W
0x0000.0000
EEPROM Run Mode Clock Gating Control
347
0x65C
RCGCWTIMER
R/W
0x0000.0000
32/64-Bit Wide General-Purpose Timer Run Mode Clock
Gating Control
348
0x700
SCGCWD
R/W
0x0000.0000
Watchdog Timer Sleep Mode Clock Gating Control
350
0x704
SCGCTIMER
R/W
0x0000.0000
16/32-Bit General-Purpose Timer Sleep Mode Clock
Gating Control
351
July 17, 2013
225
Texas Instruments-Production Data
System Control
Table 5-7. System Control Register Map (continued)
See
page
Offset
Name
Type
Reset
Description
0x708
SCGCGPIO
R/W
0x0000.0000
General-Purpose Input/Output Sleep Mode Clock Gating
Control
353
0x70C
SCGCDMA
R/W
0x0000.0000
Micro Direct Memory Access Sleep Mode Clock Gating
Control
356
0x714
SCGCHIB
R/W
0x0000.0001
Hibernation Sleep Mode Clock Gating Control
357
0x718
SCGCUART
R/W
0x0000.0000
Universal Asynchronous Receiver/Transmitter Sleep
Mode Clock Gating Control
358
0x71C
SCGCSSI
R/W
0x0000.0000
Synchronous Serial Interface Sleep Mode Clock Gating
Control
360
0x720
SCGCI2C
R/W
0x0000.0000
Inter-Integrated Circuit Sleep Mode Clock Gating Control
362
0x734
SCGCCAN
R/W
0x0000.0000
Controller Area Network Sleep Mode Clock Gating
Control
364
0x738
SCGCADC
R/W
0x0000.0000
Analog-to-Digital Converter Sleep Mode Clock Gating
Control
365
0x73C
SCGCACMP
R/W
0x0000.0000
Analog Comparator Sleep Mode Clock Gating Control
366
0x740
SCGCPWM
R/W
0x0000.0000
Pulse Width Modulator Sleep Mode Clock Gating Control
367
0x744
SCGCQEI
R/W
0x0000.0000
Quadrature Encoder Interface Sleep Mode Clock Gating
Control
368
0x758
SCGCEEPROM
R/W
0x0000.0000
EEPROM Sleep Mode Clock Gating Control
369
0x75C
SCGCWTIMER
R/W
0x0000.0000
32/64-Bit Wide General-Purpose Timer Sleep Mode Clock
Gating Control
370
0x800
DCGCWD
R/W
0x0000.0000
Watchdog Timer Deep-Sleep Mode Clock Gating Control
372
0x804
DCGCTIMER
R/W
0x0000.0000
16/32-Bit General-Purpose Timer Deep-Sleep Mode
Clock Gating Control
373
0x808
DCGCGPIO
R/W
0x0000.0000
General-Purpose Input/Output Deep-Sleep Mode Clock
Gating Control
375
0x80C
DCGCDMA
R/W
0x0000.0000
Micro Direct Memory Access Deep-Sleep Mode Clock
Gating Control
378
0x814
DCGCHIB
R/W
0x0000.0001
Hibernation Deep-Sleep Mode Clock Gating Control
379
0x818
DCGCUART
R/W
0x0000.0000
Universal Asynchronous Receiver/Transmitter
Deep-Sleep Mode Clock Gating Control
380
0x81C
DCGCSSI
R/W
0x0000.0000
Synchronous Serial Interface Deep-Sleep Mode Clock
Gating Control
382
0x820
DCGCI2C
R/W
0x0000.0000
Inter-Integrated Circuit Deep-Sleep Mode Clock Gating
Control
384
0x834
DCGCCAN
R/W
0x0000.0000
Controller Area Network Deep-Sleep Mode Clock Gating
Control
386
0x838
DCGCADC
R/W
0x0000.0000
Analog-to-Digital Converter Deep-Sleep Mode Clock
Gating Control
387
226
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Table 5-7. System Control Register Map (continued)
Description
See
page
Offset
Name
Type
Reset
0x83C
DCGCACMP
R/W
0x0000.0000
Analog Comparator Deep-Sleep Mode Clock Gating
Control
388
0x840
DCGCPWM
R/W
0x0000.0000
Pulse Width Modulator Deep-Sleep Mode Clock Gating
Control
389
0x844
DCGCQEI
R/W
0x0000.0000
Quadrature Encoder Interface Deep-Sleep Mode Clock
Gating Control
390
0x858
DCGCEEPROM
R/W
0x0000.0000
EEPROM Deep-Sleep Mode Clock Gating Control
391
0x85C
DCGCWTIMER
R/W
0x0000.0000
32/64-Bit Wide General-Purpose Timer Deep-Sleep Mode
Clock Gating Control
392
0xA00
PRWD
RO
0x0000.0000
Watchdog Timer Peripheral Ready
394
0xA04
PRTIMER
RO
0x0000.0000
16/32-Bit General-Purpose Timer Peripheral Ready
395
0xA08
PRGPIO
RO
0x0000.0000
General-Purpose Input/Output Peripheral Ready
397
0xA0C
PRDMA
RO
0x0000.0000
Micro Direct Memory Access Peripheral Ready
399
0xA14
PRHIB
RO
0x0000.0001
Hibernation Peripheral Ready
400
0xA18
PRUART
RO
0x0000.0000
Universal Asynchronous Receiver/Transmitter Peripheral
Ready
401
0xA1C
PRSSI
RO
0x0000.0000
Synchronous Serial Interface Peripheral Ready
403
0xA20
PRI2C
RO
0x0000.0000
Inter-Integrated Circuit Peripheral Ready
405
0xA34
PRCAN
RO
0x0000.0000
Controller Area Network Peripheral Ready
407
0xA38
PRADC
RO
0x0000.0000
Analog-to-Digital Converter Peripheral Ready
408
0xA3C
PRACMP
RO
0x0000.0000
Analog Comparator Peripheral Ready
409
0xA40
PRPWM
RO
0x0000.0000
Pulse Width Modulator Peripheral Ready
410
0xA44
PRQEI
RO
0x0000.0000
Quadrature Encoder Interface Peripheral Ready
411
0xA58
PREEPROM
RO
0x0000.0000
EEPROM Peripheral Ready
412
0xA5C
PRWTIMER
RO
0x0000.0000
32/64-Bit Wide General-Purpose Timer Peripheral Ready
413
System Control Legacy Registers
0x008
DC0
RO
0x007F.003F
Device Capabilities 0
415
0x010
DC1
RO
0x1333.2FFF
Device Capabilities 1
417
0x014
DC2
RO
0x070F.F337
Device Capabilities 2
420
0x018
DC3
RO
0xBFFF.FFFF
Device Capabilities 3
423
0x01C
DC4
RO
0x0004.F1FF
Device Capabilities 4
427
0x020
DC5
RO
0x0F30.00FF
Device Capabilities 5
430
0x024
DC6
RO
0x0000.0000
Device Capabilities 6
432
0x028
DC7
RO
0xFFFF.FFFF
Device Capabilities 7
433
July 17, 2013
227
Texas Instruments-Production Data
System Control
Table 5-7. System Control Register Map (continued)
Offset
Name
0x02C
Reset
DC8
RO
0xFFFF.FFFF
Device Capabilities 8
436
0x040
SRCR0
RO
0x0000.0000
Software Reset Control 0
439
0x044
SRCR1
RO
0x0000.0000
Software Reset Control 1
441
0x048
SRCR2
RO
0x0000.0000
Software Reset Control 2
444
0x100
RCGC0
RO
0x0000.0040
Run Mode Clock Gating Control Register 0
446
0x104
RCGC1
RO
0x0000.0000
Run Mode Clock Gating Control Register 1
450
0x108
RCGC2
RO
0x0000.0000
Run Mode Clock Gating Control Register 2
454
0x110
SCGC0
RO
0x0000.0040
Sleep Mode Clock Gating Control Register 0
457
0x114
SCGC1
RO
0x0000.0000
Sleep Mode Clock Gating Control Register 1
460
0x118
SCGC2
RO
0x0000.0000
Sleep Mode Clock Gating Control Register 2
464
0x120
DCGC0
RO
0x0000.0040
Deep Sleep Mode Clock Gating Control Register 0
466
0x124
DCGC1
RO
0x0000.0000
Deep-Sleep Mode Clock Gating Control Register 1
469
0x128
DCGC2
RO
0x0000.0000
Deep Sleep Mode Clock Gating Control Register 2
473
0x190
DC9
RO
0x00FF.00FF
Device Capabilities 9
475
0x1A0
NVMSTAT
RO
0x0000.0001
Non-Volatile Memory Information
477
5.5
Description
See
page
Type
System Control Register Descriptions
All addresses given are relative to the System Control base address of 0x400F.E000. Registers
provided for legacy software support only are listed in “System Control Legacy Register
Descriptions” on page 414.
228
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 1: Device Identification 0 (DID0), offset 0x000
This register identifies the version of the microcontroller. Each microcontroller is uniquely identified
by the combined values of the CLASS field in the DID0 register and the PARTNO field in the DID1
register. The MAJOR and MINOR bit fields indicate the die revision number. Combined, the MAJOR
and MINOR bit fields indicate the part revision number.
MAJOR Bitfield Value
MINOR Bitfield Value
Die Revision
Part Revision
0x0
0x0
A0
1
0x0
0x1
A1
2
0x0
0x2
A2
3
0x0
0x3
A3
4
0x1
0x0
B0
5
0x1
0x1
B1
6
Device Identification 0 (DID0)
Base 0x400F.E000
Offset 0x000
Type RO, reset 31
30
reserved
Type
Reset
29
28
27
26
VER
25
24
23
22
21
20
reserved
RO
0
RO
0
RO
0
RO
1
RO
1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
MAJOR
Type
Reset
RO
-
RO
-
RO
-
RO
-
19
18
17
16
RO
0
RO
1
RO
0
RO
1
3
2
1
0
RO
-
RO
-
RO
-
RO
-
CLASS
MINOR
RO
-
RO
-
RO
-
Bit/Field
Name
Type
Reset
31
reserved
RO
0
30:28
VER
RO
0x01
RO
-
RO
-
RO
-
RO
-
RO
-
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
DID0 Version
This field defines the DID0 register format version. The version number
is numeric. The value of the VER field is encoded as follows (all other
encodings are reserved):
Value Description
0x1
27:24
reserved
RO
0x08
Second version of the DID0 register format.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
229
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
Description
23:16
CLASS
RO
0x05
Device Class
The CLASS field value identifies the internal design from which all mask
sets are generated for all microcontrollers in a particular product line.
The CLASS field value is changed for new product lines, for changes in
fab process (for example, a remap or shrink), or any case where the
MAJOR or MINOR fields require differentiation from prior microcontrollers.
The value of the CLASS field is encoded as follows (all other encodings
are reserved):
Value Description
0x05 Tiva™ TM4C123x microcontrollers
15:8
MAJOR
RO
-
Major Die Revision
This field specifies the major revision number of the microcontroller.
The major revision reflects changes to base layers of the design. This
field is encoded as follows:
Value Description
0x0
Revision A (initial device)
0x1
Revision B (first base layer revision)
0x2
Revision C (second base layer revision)
and so on.
7:0
MINOR
RO
-
Minor Die Revision
This field specifies the minor revision number of the microcontroller.
The minor revision reflects changes to the metal layers of the design.
The MINOR field value is reset when the MAJOR field is changed. This
field is numeric and is encoded as follows:
Value Description
0x0
Initial device, or a major revision update.
0x1
First metal layer change.
0x2
Second metal layer change.
and so on.
230
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 2: Device Identification 1 (DID1), offset 0x004
This register identifies the device family, part number, temperature range, pin count, and package
type. Each microcontroller is uniquely identified by the combined values of the CLASS field in the
DID0 register and the PARTNO field in the DID1 register.
Device Identification 1 (DID1)
Base 0x400F.E000
Offset 0x004
Type RO, reset 31
30
29
28
27
26
RO
0
15
25
24
23
22
21
20
RO
0
RO
0
RO
1
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
RO
0
RO
0
14
13
12
11
10
9
8
7
6
5
4
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
0
VER
Type
Reset
FAM
PINCOUNT
Type
Reset
RO
0
RO
1
18
17
16
RO
0
RO
0
RO
1
RO
1
3
2
1
0
PARTNO
reserved
RO
0
19
TEMP
Bit/Field
Name
Type
Reset
31:28
VER
RO
0x1
RO
0
PKG
ROHS
RO
1
RO
1
QUAL
RO
-
RO
-
Description
DID1 Version
This field defines the DID1 register format version. The version number
is numeric. The value of the VER field is encoded as follows (all other
encodings are reserved):
Value Description
27:24
FAM
RO
0x0
0x0
Initial DID1 register format definition, indicating a Stellaris
LM3Snnn device.
0x1
Second version of the DID1 register format.
Family
This field provides the family identification of the device within the product
portfolio. The value is encoded as follows (all other encodings are
reserved):
Value Description
0x0
23:16
PARTNO
RO
0xC3
Tiva™ C Series microcontrollers and legacy Stellaris
microcontrollers, that is, all devices with external part numbers
starting with TM4C, LM4F or LM3S.
Part Number
This field provides the part number of the device within the family. The
reset value shown indicates the TM4C123BE6PZ microcontroller.
July 17, 2013
231
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
15:13
PINCOUNT
RO
0x2
Description
Package Pin Count
This field specifies the number of pins on the device package. The value
is encoded as follows (all other encodings are reserved):
Value Description
12:8
reserved
RO
0
7:5
TEMP
RO
0x1
0x0
reserved
0x1
reserved
0x2
100-pin package
0x3
64-pin package
0x4
144-pin package
0x5
157-pin package
0x6
168-pin package
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Temperature Range
This field specifies the temperature rating of the device. The value is
encoded as follows (all other encodings are reserved):
Value Description
4:3
PKG
RO
0x1
0x0
Reserved
0x1
Industrial temperature range (-40°C to 85°C)
0x2
Extended temperature range (-40°C to 105°C)
0x3
Available in both industrial temperature range (-40°C to 85°C)
and extended temperature range (-40°C to 105°C) devices. See
“Package Information” on page 1296 for specific order numbers.
Package Type
This field specifies the package type. The value is encoded as follows
(all other encodings are reserved):
Value Description
2
ROHS
RO
0x1
0x0
Reserved
0x1
LQFP package
0x2
BGA package
RoHS-Compliance
This bit specifies whether the device is RoHS-compliant. A 1 indicates
the part is RoHS-compliant.
232
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
1:0
QUAL
RO
-
Description
Qualification Status
This field specifies the qualification status of the device. The value is
encoded as follows (all other encodings are reserved):
Value Description
0x0
Engineering Sample (unqualified)
0x1
Pilot Production (unqualified)
0x2
Fully Qualified
July 17, 2013
233
Texas Instruments-Production Data
System Control
Register 3: Brown-Out Reset Control (PBORCTL), offset 0x030
This register is responsible for controlling reset conditions after initial power-on reset.
Note:
The BOR voltage values and center points are based on simulation only. These values are
yet to be characterized and are subject to change.
Brown-Out Reset Control (PBORCTL)
Base 0x400F.E000
Offset 0x030
Type R/W, reset 0x0000.7FFF
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
4
3
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
2
1
0
BOR0
BOR1
reserved
R/W
1
R/W
1
RO
0
Bit/Field
Name
Type
Reset
Description
31:3
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
2
BOR0
R/W
1
VDD under BOR0 Event Action
The VDD BOR0 trip value is 3.02V +/- 90mv.
Value Description
1
BOR1
R/W
1
0
A BOR0 event causes an interrupt to be generated in the
interrupt controller.
1
A BOR0 event causes a reset of the microcontroller.
VDD under BOR1 Event Action
The VDD BOR1 trip value is 2.88V +/- 90mv.
Value Description
0
reserved
RO
0
0
A BOR1 event causes an interrupt to be generated to the
interrupt controller.
1
A BOR1 event causes a reset of the microcontroller.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
234
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 4: Raw Interrupt Status (RIS), offset 0x050
This register indicates the status for system control raw interrupts. An interrupt is sent to the interrupt
controller if the corresponding bit in the Interrupt Mask Control (IMC) register is set. Writing a 1
to the corresponding bit in the Masked Interrupt Status and Clear (MISC) register clears an interrupt
status bit.
Raw Interrupt Status (RIS)
Base 0x400F.E000
Offset 0x050
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
reserved
Type
Reset
reserved
Type
Reset
BOR0RIS VDDARIS reserved
RO
0
RO
0
RO
0
RO
0
MOSCPUPRIS
RO
0
Bit/Field
Name
Type
Reset
31:12
reserved
RO
0x0000.00
11
BOR0RIS
RO
0
RO
0
reserved PLLLRIS
RO
0
RO
0
reserved
RO
0
MOFRIS
RO
0
RO
0
reserved BOR1RIS reserved
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
VDD under BOR0 Raw Interrupt Status
Value Description
1
A VDD BOR0 condition is currently active.
0
A VDD BOR0 condition is not currently active.
Note the BOR0 bit in the PBORCTL register must be cleared to cause
an interrupt due to a BOR0 Event.
This bit is cleared by writing a 1 to the BOR0MIS bit in the MISC register.
10
VDDARIS
RO
0
VDDA Power OK Event Raw Interrupt Status
Value Description
1
VDDA is at an appropriate functional voltage.
0
VDDA power is not at its appropriate functional voltage.
This bit is cleared by writing a 1 to the VDDAMIS bit in the MISC register.
9
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
235
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
8
MOSCPUPRIS
RO
0
Description
MOSC Power Up Raw Interrupt Status
Value Description
1
Sufficient time has passed for the MOSC to reach the expected
frequency. The value for this power-up time is indicated by
TMOSC_START.
0
Sufficient time has not passed for the MOSC to reach the
expected frequency.
This bit is cleared by writing a 1 to the MOSCPUPMIS bit in the MISC
register.
7
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
6
PLLLRIS
RO
0
PLL Lock Raw Interrupt Status
Value Description
1
The PLL timer has reached TREADY indicating that sufficient time
has passed for the PLL to lock.
0
The PLL timer has not reached TREADY.
This bit is cleared by writing a 1 to the PLLLMIS bit in the MISC register.
5:4
reserved
RO
0x0
3
MOFRIS
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Main Oscillator Failure Raw Interrupt Status
Value Description
1
The MOSCIM bit in the MOSCCTL register is set and the main
oscillator has failed.
0
The main oscillator has not failed.
This bit is cleared by writing a 1 to the MOFMIS bit in the MISC register.
2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
BOR1RIS
RO
0
VDD under BOR1 Raw Interrupt Status
Value Description
1
A VDDS BOR1 condition is currently active.
0
A VDDS BOR1 condition is not currently active.
Note the BOR1 bit in the PBORCTL register must be cleared to cause
an interrupt due to a BOR1 Event.
This bit is cleared by writing a 1 to the BOR1MIS bit in the MISC register.
0
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
236
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 5: Interrupt Mask Control (IMC), offset 0x054
This register contains the mask bits for system control raw interrupts. A raw interrupt, indicated by
a bit being set in the Raw Interrupt Status (RIS) register, is sent to the interrupt controller if the
corresponding bit in this register is set.
Interrupt Mask Control (IMC)
Base 0x400F.E000
Offset 0x054
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
BOR0IM
VDDAIM
RO
0
RO
0
R/W
0
R/W
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
reserved
MOSCPUPIM
reserved
PLLLIM
MOFIM
reserved
BOR1IM
reserved
RO
0
R/W
0
RO
0
R/W
0
R/W
0
RO
0
R/W
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:12
reserved
RO
0x0000.00
11
BOR0IM
R/W
0
reserved
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
VDD under BOR0 Interrupt Mask
Value Description
10
VDDAIM
R/W
0
1
An interrupt is sent to the interrupt controller when the BOR0RIS
bit in the RIS register is set.
0
The BOR0RIS interrupt is suppressed and not sent to the
interrupt controller.
VDDA Power OK Interrupt Mask
Value Description
1
An interrupt is sent to the interrupt controller when the VDDARIS
bit in the RIS register is set.
0
The VDDARIS interrupt is suppressed and not sent to the
interrupt controller.
9
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
8
MOSCPUPIM
R/W
0
MOSC Power Up Interrupt Mask
Value Description
1
An interrupt is sent to the interrupt controller when the
MOSCPUPRIS bit in the RIS register is set.
0
The MOSCPUPRIS interrupt is suppressed and not sent to the
interrupt controller.
July 17, 2013
237
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
Description
7
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
6
PLLLIM
R/W
0
PLL Lock Interrupt Mask
Value Description
5:4
reserved
RO
0x0
3
MOFIM
R/W
0
1
An interrupt is sent to the interrupt controller when the PLLLRIS
bit in the RIS register is set.
0
The PLLLRIS interrupt is suppressed and not sent to the
interrupt controller.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Main Oscillator Failure Interrupt Mask
Value Description
1
An interrupt is sent to the interrupt controller when the MOFRIS
bit in the RIS register is set.
0
The MOFRIS interrupt is suppressed and not sent to the interrupt
controller.
2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
BOR1IM
R/W
0
VDD under BOR1 Interrupt Mask
Value Description
0
reserved
RO
0
1
An interrupt is sent to the interrupt controller when the BOR1RIS
bit in the RIS register is set.
0
The BOR1RIS interrupt is suppressed and not sent to the
interrupt controller.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
238
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 6: Masked Interrupt Status and Clear (MISC), offset 0x058
On a read, this register gives the current masked status value of the corresponding interrupt in the
Raw Interrupt Status (RIS) register. All of the bits are R/W1C, thus writing a 1 to a bit clears the
corresponding raw interrupt bit in the RIS register (see page 235).
Masked Interrupt Status and Clear (MISC)
Base 0x400F.E000
Offset 0x058
Type R/W1C, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
reserved
Type
Reset
reserved
Type
Reset
BOR0MIS VDDAMIS reserved
RO
0
RO
0
R/W1C
0
R/W1C
0
MOSCPUPMIS
RO
0
Bit/Field
Name
Type
Reset
31:12
reserved
RO
0x0000.00
11
BOR0MIS
R/W1C
0
R/W1C
0
reserved PLLLMIS
RO
0
R/W1C
0
reserved
RO
0
RO
0
MOFMIS reserved BOR1MIS reserved
RO
0
RO
0
R/W1C
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
VDD under BOR0 Masked Interrupt Status
Value Description
1
When read, a 1 indicates that an unmasked interrupt was
signaled because of a BOR0 condition.
Writing a 1 to this bit clears it and also the BOR0RIS bit in the
RIS register.
0
When read, a 0 indicates that a BOR0 condition has not
occurred.
A write of 0 has no effect on the state of this bit.
10
VDDAMIS
R/W1C
0
VDDA Power OK Masked Interrupt Status
Value Description
1
When read, a 1 indicates that an unmasked interrupt was
signaled because VDDA was below the proper functioning
voltage.
Writing a 1 to this bit clears it and also the VDDARIS bit in the
RIS register.
0
When read, a 0 indicates that VDDA power is good.
A write of 0 has no effect on the state of this bit.
9
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
239
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
8
MOSCPUPMIS
R/W1C
0
Description
MOSC Power Up Masked Interrupt Status
Value Description
1
When read, a 1 indicates that an unmasked interrupt was
signaled because sufficient time has passed for the MOSC PLL
to lock.
Writing a 1 to this bit clears it and also the MOSCPUPRIS bit in
the RIS register.
0
When read, a 0 indicates that sufficient time has not passed for
the MOSC PLL to lock.
A write of 0 has no effect on the state of this bit.
7
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
6
PLLLMIS
R/W1C
0
PLL Lock Masked Interrupt Status
Value Description
1
When read, a 1 indicates that an unmasked interrupt was
signaled because sufficient time has passed for the PLL to lock.
Writing a 1 to this bit clears it and also the PLLLRIS bit in the
RIS register.
0
When read, a 0 indicates that sufficient time has not passed for
the PLL to lock.
A write of 0 has no effect on the state of this bit.
5:4
reserved
RO
0x0
3
MOFMIS
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Main Oscillator Failure Masked Interrupt Status
Value Description
1
When read, a 1 indicates that an unmasked interrupt was
signaled because the main oscillator failed.
Writing a 1 to this bit clears it and also the MOFRIS bit in the
RIS register.
0
When read, a 0 indicates that the main oscillator has not failed.
A write of 0 has no effect on the state of this bit.
2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
240
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
1
BOR1MIS
R/W1C
0
Description
VDD under BOR1 Masked Interrupt Status
Value Description
1
When read, a 1 indicates that an unmasked interrupt was
signaled because of a BOR1 condition.
Writing a 1 to this bit clears it and also the BOR1RIS bit in the
RIS register.
0
When read, a 0 indicates that a BOR1 condition has not
occurred.
A write of 0 has no effect on the state of this bit.
0
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
241
Texas Instruments-Production Data
System Control
Register 7: Reset Cause (RESC), offset 0x05C
This register is set with the reset cause after reset. The bits in this register are sticky and maintain
their state across multiple reset sequences, except when an power-on reset is the cause, in which
case, all bits other than POR in the RESC register are cleared.
Reset Cause (RESC)
Base 0x400F.E000
Offset 0x05C
Type R/W, reset 31
30
29
28
27
26
25
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
RO
0
RO
0
RO
0
RO
0
RO
0
24
23
22
21
20
19
18
17
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
-
9
8
7
6
5
4
3
2
1
0
WDT1
SW
WDT0
BOR
POR
EXT
RO
0
RO
0
RO
0
RO
0
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
R/W
-
reserved
Type
Reset
MOSCFAIL
reserved
Type
Reset
RO
0
16
Bit/Field
Name
Type
Reset
Description
31:17
reserved
RO
0x000
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
16
MOSCFAIL
R/W
-
MOSC Failure Reset
Value Description
1
When read, this bit indicates that the MOSC circuit was enabled
for clock validation and failed while the MOSCIM bit in the
MOSCCTL register is clear, generating a reset event.
0
When read, this bit indicates that a MOSC failure has not
generated a reset since the previous power-on reset.
Writing a 0 to this bit clears it.
15:6
reserved
RO
0x00
5
WDT1
R/W
-
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Watchdog Timer 1 Reset
Value Description
1
When read, this bit indicates that Watchdog Timer 1 timed out
and generated a reset.
0
When read, this bit indicates that Watchdog Timer 1 has not
generated a reset since the previous power-on reset.
Writing a 0 to this bit clears it.
242
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
4
SW
R/W
-
Description
Software Reset
Value Description
1
When read, this bit indicates that a software reset has caused
a reset event.
0
When read, this bit indicates that a software reset has not
generated a reset since the previous power-on reset.
Writing a 0 to this bit clears it.
3
WDT0
R/W
-
Watchdog Timer 0 Reset
Value Description
1
When read, this bit indicates that Watchdog Timer 0 timed out
and generated a reset.
0
When read, this bit indicates that Watchdog Timer 0 has not
generated a reset since the previous power-on reset.
Writing a 0 to this bit clears it.
2
BOR
R/W
-
Brown-Out Reset
Value Description
1
When read, this bit indicates that a brown-out (BOR0 or BOR1)
reset has caused a reset event.
0
When read, this bit indicates that a brown-out (BOR0 or BOR1)
reset has not generated a reset since the previous power-on
reset.
Writing a 0 to this bit clears it.
1
POR
R/W
-
Power-On Reset
Value Description
1
When read, this bit indicates that a power-on reset has caused
a reset event.
0
When read, this bit indicates that a power-on reset has not
generated a reset.
Writing a 0 to this bit clears it.
0
EXT
R/W
-
External Reset
Value Description
1
When read, this bit indicates that an external reset (RST
assertion) has caused a reset event.
0
When read, this bit indicates that an external reset (RST
assertion) has not caused a reset event since the previous
power-on reset.
Writing a 0 to this bit clears it.
July 17, 2013
243
Texas Instruments-Production Data
System Control
Register 8: Run-Mode Clock Configuration (RCC), offset 0x060
The bits in this register configure the system clock and oscillators.
Important: Write the RCC register prior to writing the RCC2 register. If a subsequent write to the
RCC register is required, include another register access after writing the RCC register
and before writing the RCC2 register.
Run-Mode Clock Configuration (RCC)
Base 0x400F.E000
Offset 0x060
Type R/W, reset 0x078E.3AD1
31
30
29
28
RO
0
RO
0
RO
0
RO
0
15
14
13
12
reserved
Type
Reset
reserved
Type
Reset
RO
0
RO
0
27
26
25
24
23
R/W
0
R/W
1
R/W
1
R/W
1
R/W
1
11
10
9
8
R/W
0
R/W
1
ACG
PWRDN
RO
1
21
20
USESYSDIV
reserved
USEPWMDIV
R/W
0
RO
0
R/W
0
R/W
1
R/W
1
R/W
1
RO
0
7
6
5
4
3
2
1
0
R/W
1
R/W
1
R/W
0
R/W
1
RO
0
SYSDIV
reserved BYPASS
R/W
1
22
XTAL
R/W
1
Bit/Field
Name
Type
Reset
31:28
reserved
RO
0x0
27
ACG
R/W
0
R/W
0
19
18
17
PWMDIV
OSCSRC
reserved
reserved
RO
0
16
MOSCDIS
RO
0
R/W
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Auto Clock Gating
This bit specifies whether the system uses the Sleep-Mode Clock
Gating Control (SCGCn) registers and Deep-Sleep-Mode Clock
Gating Control (DCGCn) registers if the microcontroller enters a Sleep
or Deep-Sleep mode (respectively).
Value Description
1
The SCGCn or DCGCn registers are used to control the clocks
distributed to the peripherals when the microcontroller is in a
sleep mode. The SCGCn and DCGCn registers allow unused
peripherals to consume less power when the microcontroller is
in a sleep mode.
0
The Run-Mode Clock Gating Control (RCGCn) registers are
used when the microcontroller enters a sleep mode.
The RCGCn registers are always used to control the clocks in Run
mode.
26:23
SYSDIV
R/W
0xF
System Clock Divisor
Specifies which divisor is used to generate the system clock from either
the PLL output or the oscillator source (depending on how the BYPASS
bit in this register is configured). See Table 5-4 on page 215 for bit
encodings.
If the SYSDIV value is less than MINSYSDIV (see page 417), and the
PLL is being used, then the MINSYSDIV value is used as the divisor.
If the PLL is not being used, the SYSDIV value can be less than
MINSYSDIV.
244
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
22
USESYSDIV
R/W
0
Description
Enable System Clock Divider
Value Description
1
The system clock divider is the source for the system clock. The
system clock divider is forced to be used when the PLL is
selected as the source.
If the USERCC2 bit in the RCC2 register is set, then the SYSDIV2
field in the RCC2 register is used as the system clock divider
rather than the SYSDIV field in this register.
0
The system clock is used undivided.
21
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
20
USEPWMDIV
R/W
0
Enable PWM Clock Divisor
Value Description
1
The PWM clock divider is the source for the PWM clock.
0
The system clock is the source for the PWM clock.
Note that when the PWM divisor is used, it is applied to the clock for
both PWM modules.
19:17
PWMDIV
R/W
0x7
PWM Unit Clock Divisor
This field specifies the binary divisor used to predivide the system clock
down for use as the timing reference for the PWM module. The rising
edge of this clock is synchronous with the system clock.
Value Divisor
16:14
reserved
RO
0x0
13
PWRDN
R/W
1
0x0
/2
0x1
/4
0x2
/8
0x3
/16
0x4
/32
0x5
/64
0x6
/64
0x7
/64 (default)
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PLL Power Down
Value Description
1
The PLL is powered down. Care must be taken to ensure that
another clock source is functioning and that the BYPASS bit is
set before setting this bit.
0
The PLL is operating normally.
July 17, 2013
245
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
Description
12
reserved
RO
1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
11
BYPASS
R/W
1
PLL Bypass
Value Description
1
The system clock is derived from the OSC source and divided
by the divisor specified by SYSDIV.
0
The system clock is the PLL output clock divided by the divisor
specified by SYSDIV.
See Table 5-4 on page 215 for programming guidelines.
Note:
10:6
XTAL
R/W
0x0B
The ADC must be clocked from the PLL or directly from a
16-MHz clock source to operate properly.
Crystal Value
This field specifies the crystal value attached to the main oscillator. The
encoding for this field is provided below.
Value
Crystal Frequency (MHz) Not
Using the PLL
0x00-0x5
0x06
Crystal Frequency (MHz)
Using the PLL
reserved
4 MHz
reserved
0x07
4.096 MHz
reserved
0x08
4.9152 MHz
reserved
0x09
5 MHz
0x0A
5.12 MHz
0x0B
6 MHz
0x0C
6.144 MHz
0x0D
7.3728 MHz
0x0E
8 MHz
0x0F
8.192 MHz
0x10
10.0 MHz
0x11
12.0 MHz
0x12
12.288 MHz
0x13
13.56 MHz
0x14
14.31818 MHz
0x15
16.0 MHz
0x16
16.384 MHz
0x17
18.0 MHz
0x18
20.0 MHz
0x19
24.0 MHz
0x1A
25.0 MHz
246
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
5:4
OSCSRC
R/W
0x1
Description
Oscillator Source
Selects the input source for the OSC. The values are:
Value Input Source
0x0
MOSC
Main oscillator
0x1
PIOSC
Precision internal oscillator
(default)
0x2
PIOSC/4
Precision internal oscillator / 4
0x3
LFIOSC
Low-frequency internal oscillator
For additional oscillator sources, see the RCC2 register.
3:1
reserved
RO
0x0
0
MOSCDIS
R/W
1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Main Oscillator Disable
Value Description
1
The main oscillator is disabled (default).
0
The main oscillator is enabled.
July 17, 2013
247
Texas Instruments-Production Data
System Control
Register 9: GPIO High-Performance Bus Control (GPIOHBCTL), offset 0x06C
This register controls which internal bus is used to access each GPIO port. When a bit is clear, the
corresponding GPIO port is accessed across the legacy Advanced Peripheral Bus (APB) bus and
through the APB memory aperture. When a bit is set, the corresponding port is accessed across
the Advanced High-Performance Bus (AHB) bus and through the AHB memory aperture. Each
GPIO port can be individually configured to use AHB or APB, but may be accessed only through
one aperture. The AHB bus provides better back-to-back access performance than the APB bus.
The address aperture in the memory map changes for the ports that are enabled for AHB access
(see Table 10-6 on page 651).
Important: Ports K-N and P-Q are only available on the AHB bus, and therefore the corresponding
bits reset to 1. If one of these bits is cleared, the corresponding port is disabled. If any
of these ports is in use, read-modify-write operations should be used to change the
value of this register so that these ports remain enabled.
GPIO High-Performance Bus Control (GPIOHBCTL)
Base 0x400F.E000
Offset 0x06C
Type R/W, reset 0x0000.7E00
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
PORTK
PORTJ
PORTH
PORTG
PORTF
PORTE
PORTD
PORTC
PORTB
PORTA
R/W
1
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
31:10
reserved
RO
0x0000.0
9
PORTK
R/W
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Port K Advanced High-Performance Bus
This bit defines the memory aperture for Port K.
Value Description
8
PORTJ
R/W
0
1
Advanced High-Performance Bus (AHB)
0
Port K is disabled.
Port J Advanced High-Performance Bus
This bit defines the memory aperture for Port J.
Value Description
1
Advanced High-Performance Bus (AHB)
0
Advanced Peripheral Bus (APB). This bus is the legacy bus.
248
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
7
PORTH
R/W
0
Description
Port H Advanced High-Performance Bus
This bit defines the memory aperture for Port H.
Value Description
6
PORTG
R/W
0
1
Advanced High-Performance Bus (AHB)
0
Advanced Peripheral Bus (APB). This bus is the legacy bus.
Port G Advanced High-Performance Bus
This bit defines the memory aperture for Port G.
Value Description
5
PORTF
R/W
0
1
Advanced High-Performance Bus (AHB)
0
Advanced Peripheral Bus (APB). This bus is the legacy bus.
Port F Advanced High-Performance Bus
This bit defines the memory aperture for Port F.
Value Description
4
PORTE
R/W
0
1
Advanced High-Performance Bus (AHB)
0
Advanced Peripheral Bus (APB). This bus is the legacy bus.
Port E Advanced High-Performance Bus
This bit defines the memory aperture for Port E.
Value Description
3
PORTD
R/W
0
1
Advanced High-Performance Bus (AHB)
0
Advanced Peripheral Bus (APB). This bus is the legacy bus.
Port D Advanced High-Performance Bus
This bit defines the memory aperture for Port D.
Value Description
2
PORTC
R/W
0
1
Advanced High-Performance Bus (AHB)
0
Advanced Peripheral Bus (APB). This bus is the legacy bus.
Port C Advanced High-Performance Bus
This bit defines the memory aperture for Port C.
Value Description
1
Advanced High-Performance Bus (AHB)
0
Advanced Peripheral Bus (APB). This bus is the legacy bus.
July 17, 2013
249
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
1
PORTB
R/W
0
Description
Port B Advanced High-Performance Bus
This bit defines the memory aperture for Port B.
Value Description
0
PORTA
R/W
0
1
Advanced High-Performance Bus (AHB)
0
Advanced Peripheral Bus (APB). This bus is the legacy bus.
Port A Advanced High-Performance Bus
This bit defines the memory aperture for Port A.
Value Description
1
Advanced High-Performance Bus (AHB)
0
Advanced Peripheral Bus (APB). This bus is the legacy bus.
250
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 10: Run-Mode Clock Configuration 2 (RCC2), offset 0x070
This register overrides the RCC equivalent register fields, as shown in Table 5-8, when the USERCC2
bit is set, allowing the extended capabilities of the RCC2 register to be used while also providing a
means to be backward-compatible to previous parts. Each RCC2 field that supersedes an RCC
field is located at the same LSB bit position; however, some RCC2 fields are larger than the
corresponding RCC field.
Table 5-8. RCC2 Fields that Override RCC Fields
RCC2 Field...
Overrides RCC Field
SYSDIV2, bits[28:23]
SYSDIV, bits[26:23]
PWRDN2, bit[13]
PWRDN, bit[13]
BYPASS2, bit[11]
BYPASS, bit[11]
OSCSRC2, bits[6:4]
OSCSRC, bits[5:4]
Important: Write the RCC register prior to writing the RCC2 register. If a subsequent write to the
RCC register is required, include another register access after writing the RCC register
and before writing the RCC2 register.
Run-Mode Clock Configuration 2 (RCC2)
Base 0x400F.E000
Offset 0x070
Type R/W, reset 0x07C0.6810
31
30
USERCC2 DIV400
Type
Reset
R/W
0
R/W
0
15
14
reserved
Type
Reset
RO
0
RO
0
29
28
27
26
reserved
25
24
23
SYSDIV2
22
RO
0
R/W
0
R/W
0
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
13
12
11
10
9
8
7
6
PWRDN2 reserved BYPASS2
R/W
1
RO
0
reserved
R/W
1
RO
0
21
20
19
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31
USERCC2
R/W
0
Use RCC2
R/W
0
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
RO
0
RO
0
OSCSRC2
RO
0
18
reserved
SYSDIV2LSB
R/W
0
reserved
R/W
1
RO
0
RO
0
Value Description
30
DIV400
R/W
0
1
The RCC2 register fields override the RCC register fields.
0
The RCC register fields are used, and the fields in RCC2 are
ignored.
Divide PLL as 400 MHz vs. 200 MHz
This bit, along with the SYSDIV2LSB bit, allows additional frequency
choices.
Value Description
1
Append the SYSDIV2LSB bit to the SYSDIV2 field to create a
7 bit divisor using the 400 MHz PLL output, see Table
5-6 on page 216.
0
Use SYSDIV2 as is and apply to 200 MHz predivided PLL
output. See Table 5-5 on page 215 for programming guidelines.
July 17, 2013
251
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
29
reserved
RO
0x0
28:23
SYSDIV2
R/W
0x0F
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
System Clock Divisor 2
Specifies which divisor is used to generate the system clock from either
the PLL output or the oscillator source (depending on how the BYPASS2
bit is configured). SYSDIV2 is used for the divisor when both the
USESYSDIV bit in the RCC register and the USERCC2 bit in this register
are set. See Table 5-5 on page 215 for programming guidelines.
22
SYSDIV2LSB
R/W
1
Additional LSB for SYSDIV2
When DIV400 is set, this bit becomes the LSB of SYSDIV2. If DIV400
is clear, this bit is not used. See Table 5-5 on page 215 for programming
guidelines.
This bit can only be set or cleared when DIV400 is set.
21:14
reserved
RO
0x0
13
PWRDN2
R/W
1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Power-Down PLL 2
Value Description
1
The PLL is powered down.
0
The PLL operates normally.
12
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
11
BYPASS2
R/W
1
PLL Bypass 2
Value Description
1
The system clock is derived from the OSC source and divided
by the divisor specified by SYSDIV2.
0
The system clock is the PLL output clock divided by the divisor
specified by SYSDIV2.
See Table 5-5 on page 215 for programming guidelines.
Note:
10:7
reserved
RO
0x0
The ADC must be clocked from the PLL or directly from a
16-MHz clock source to operate properly.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
252
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
6:4
OSCSRC2
R/W
0x1
Description
Oscillator Source 2
Selects the input source for the OSC. The values are:
Value
Description
0x0
MOSC
Main oscillator
0x1
PIOSC
Precision internal oscillator
0x2
PIOSC/4
Precision internal oscillator / 4
0x3
LFIOSC
Low-frequency internal oscillator
0x4-0x6 Reserved
0x7
32.768 kHz
32.768-kHz external oscillator
3:0
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
253
Texas Instruments-Production Data
System Control
Register 11: Main Oscillator Control (MOSCCTL), offset 0x07C
This register provides control over the features of the main oscillator, including the ability to enable
the MOSC clock verification circuit, what action to take when the MOSC fails, and whether or not a
crystal is connected. When enabled, this circuit monitors the frequency of the MOSC to verify that
the oscillator is operating within specified limits. If the clock goes invalid after being enabled, the
microcontroller issues a power-on reset and reboots to the NMI handler or generates an interrupt.
Main Oscillator Control (MOSCCTL)
Base 0x400F.E000
Offset 0x07C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
31:3
reserved
RO
0x0000.000
2
NOXTAL
R/W
0
NOXTAL MOSCIM
R/W
0
R/W
0
CVAL
R/W
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
No Crystal Connected
Value Description
1
MOSCIM
R/W
0
1
This bit should be set when a crystal or external oscillator is not
connected to the OSC0 and OSC1 inputs to reduce power
consumption.
0
This bit should be cleared when a crystal or oscillator is
connected to the OSC0 and OSC1 inputs, regardless of whether
or not the MOSC is used or powered down.
MOSC Failure Action
Value Description
1
If the MOSC fails, an interrupt is generated as indicated by the
MOFRIS bit in the RIS register..
0
If the MOSC fails, a MOSC failure reset is generated and reboots
to the NMI handler.
Regardless of the action taken, if the MOSC fails, the oscillator source
is switched to the PIOSC automatically.
0
CVAL
R/W
0
Clock Validation for MOSC
Value Description
1
The MOSC monitor circuit is enabled.
0
The MOSC monitor circuit is disabled.
254
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 12: Deep Sleep Clock Configuration (DSLPCLKCFG), offset 0x144
This register provides configuration information for the hardware control of Deep Sleep Mode.
Deep Sleep Clock Configuration (DSLPCLKCFG)
Base 0x400F.E000
Offset 0x144
Type R/W, reset 0x0780.0000
31
30
29
28
27
26
reserved
Type
Reset
25
24
23
22
21
20
DSDIVORIDE
18
17
16
reserved
RO
0
RO
0
RO
0
R/W
0
R/W
0
R/W
1
R/W
1
R/W
1
R/W
1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
RO
0
reserved
Type
Reset
19
DSOSCSRC
RO
0
Bit/Field
Name
Type
Reset
31:29
reserved
RO
0x0
28:23
DSDIVORIDE
R/W
0x0F
R/W
0
reserved
RO
0
PIOSCPD reserved
R/W
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Divider Field Override
If Deep-Sleep mode is enabled when the PLL is running, the PLL is
disabled. This 6-bit field contains a system divider field that overrides
the SYSDIV field in the RCC register or the SYSDIV2 field in the RCC2
register during Deep Sleep. This divider is applied to the source selected
by the DSOSCSRC field.
Value Description
0x0
/1
0x1
/2
0x2
/3
0x3
/4
...
...
0x3F /64
22:7
reserved
RO
0x000
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
255
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
6:4
DSOSCSRC
R/W
0x0
Description
Clock Source
Specifies the clock source during Deep-Sleep mode.
Value
Description
0x0
MOSC
Use the main oscillator as the source. To use the MOSC as
the Deep-Sleep mode clock source, the MOSC must also be
configured as the Run mode clock source in the Run-Mode
Clock Configuration (RCC) register.
Note:
0x1
If the PIOSC is being used as the clock reference
for the PLL, the PIOSC is the clock source instead
of MOSC in Deep-Sleep mode.
PIOSC
Use the precision internal 16-MHz oscillator as the source.
0x2
Reserved
0x3
LFIOSC
Use the low-frequency internal oscillator as the source.
0x4-0x6 Reserved
0x7
32.768 kHz
Use the Hibernation module 32.768-kHz external oscillator
as the source.
3:2
reserved
RO
0x0
1
PIOSCPD
R/W
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PIOSC Power Down Request
Allows software to request the PIOSC to be powered-down in
Deep-Sleep mode. If the PIOSC is needed by an enabled peripheral
during Deep-Sleep, the PIOSC is powered down, but a warning is
generated using the PPDW bit in the SDPMST register. If it is not possible
to power down the PIOSC, an error is reported using the PPDERR bit in
the SDPMST register.
This bit can only be used to power down the PIOSC when the PIOSCPDE
bit in the SYSPROP register is set.
Value Description
0
reserved
RO
0
0
No action.
1
Software requests that the PIOSC is powered down during
Deep-Sleep mode.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
256
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 13: System Properties (SYSPROP), offset 0x14C
This register provides information on whether certain System Control properties are present on the
microcontroller.
System Properties (SYSPROP)
Base 0x400F.E000
Offset 0x14C
Type RO, reset 0x0000.1D31
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
1
RO
1
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
RO
0
PIOSCPDE
RO
0
RO
1
SRAMSM SRAMLPM reserved FLASHLPM
RO
1
RO
1
RO
0
RO
1
reserved
RO
0
reserved
reserved
RO
0
FPU
RO
0
RO
1
Bit/Field
Name
Type
Reset
Description
31:13
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
12
PIOSCPDE
RO
0x1
PIOSC Power Down Present
This bit determines whether the PIOSCPD bit in the DSLPCLKCFG
register can be set to power down the PIOSC in Deep-sleep mode.
Value Description
11
SRAMSM
RO
0x1
0
The status of the PIOSCPD bit is ignored.
1
The PIOSCPD bit can be set to power down the PIOSC in
Deep-sleep mode.
SRAM Sleep/Deep-sleep Standby Mode Present
This bit determines whether the SRAMPM field in the SLPPWRCFG and
DSLPPWRCFG registers can be configured to put the SRAM into
Standby mode while in Sleep or Deep-sleep mode.
Value Description
10
SRAMLPM
RO
0x1
0
A value of 0x1 in the SRAMPM fields is ignored.
1
The SRAMPM fields can be configured to put the SRAM into
Standby mode while in Sleep or Deep-sleep mode.
SRAM Sleep/Deep-sleep Low Power Mode Present
This bit determines whether the SRAMPM field in the SLPPWRCFG and
DSLPPWRCFG registers can be configured to put the SRAM into Low
Power mode while in Sleep or Deep-sleep mode.
Value Description
0
A value of 0x3 in the SRAMPM fields is ignored.
1
The SRAMPM fields can be configured to put the SRAM into Low
Power mode while in Sleep or Deep-sleep mode.
July 17, 2013
257
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
9
reserved
RO
0
8
FLASHLPM
RO
0x1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Flash Memory Sleep/Deep-sleep Low Power Mode Present
This bit determines whether the FLASHPM field in the SLPPWRCFG
and DSLPPWRCFG registers can be configured to put the Flash memory
into Low Power mode while in Sleep or Deep-sleep mode.
Value Description
0
A value of 0x2 in the FLASHPM fields is ignored.
1
The FLASHPM fields can be configured to put the Flash memory
into Low Power mode while in Sleep or Deep-sleep mode.
7:6
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5:4
reserved
RO
0x3
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
FPU
RO
0x1
FPU Present
This bit indicates if the FPU is present in the Cortex-M4 core.
Value Description
0
FPU is not present.
1
FPU is present.
258
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 14: Precision Internal Oscillator Calibration (PIOSCCAL), offset 0x150
This register provides the ability to update or recalibrate the precision internal oscillator. Note that
a 32.768-kHz oscillator must be used as the Hibernation module clock source for the user to be
able to calibrate the PIOSC.
Precision Internal Oscillator Calibration (PIOSCCAL)
Base 0x400F.E000
Offset 0x150
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
R/W
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
UTEN
Type
Reset
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
reserved
Type
Reset
23
RO
0
CAL
R/W
0
Bit/Field
Name
Type
Reset
31
UTEN
R/W
0
UPDATE reserved
R/W
0
RO
0
UT
Description
Use User Trim Value
Value Description
30:10
reserved
RO
0x0000
9
CAL
R/W
0
1
The trim value in bits[6:0] of this register are used for any update
trim operation.
0
The factory calibration value is used for an update trim operation.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Start Calibration
Value Description
1
Starts a new calibration of the PIOSC. Results are in the
PIOSCSTAT register. The resulting trim value from the operation
is active in the PIOSC after the calibration completes. The result
overrides any previous update trim operation whether the
calibration passes or fails.
0
No action.
This bit is auto-cleared after it is set.
8
UPDATE
R/W
0
Update Trim
Value Description
1
Updates the PIOSC trim value with the UT bit or the DT bit in
the PIOSCSTAT register. Used with UTEN.
0
No action.
This bit is auto-cleared after the update.
7
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
259
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
6:0
UT
R/W
0x0
Description
User Trim Value
User trim value that can be loaded into the PIOSC.
Refer to “Main PLL Frequency Configuration” on page 217 for more
information on calibrating the PIOSC.
260
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 15: Precision Internal Oscillator Statistics (PIOSCSTAT), offset 0x154
This register provides the user information on the PIOSC calibration. Note that a 32.768-kHz oscillator
must be used as the Hibernation module clock source for the user to be able to calibrate the PIOSC.
Precision Internal Oscillator Statistics (PIOSCSTAT)
Base 0x400F.E000
Offset 0x154
Type RO, reset 0x0000.0040
31
30
29
28
RO
0
RO
0
RO
0
RO
0
15
14
13
12
RO
0
RO
0
RO
0
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
-
RO
-
RO
-
RO
-
RO
-
RO
-
RO
-
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
DT
reserved
Type
Reset
RO
0
RESULT
reserved
RO
0
RO
0
CT
Bit/Field
Name
Type
Reset
Description
31:23
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
22:16
DT
RO
-
Default Trim Value
This field contains the default trim value. This value is loaded into the
PIOSC after every full power-up.
15:10
reserved
RO
0x0
9:8
RESULT
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Calibration Result
Value Description
7
reserved
RO
0
6:0
CT
RO
0x40
0x0
Calibration has not been attempted.
0x1
The last calibration operation completed to meet 1% accuracy.
0x2
The last calibration operation failed to meet 1% accuracy.
0x3
Reserved
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Calibration Trim Value
This field contains the trim value from the last calibration operation. After
factory calibration CT and DT are the same.
July 17, 2013
261
Texas Instruments-Production Data
System Control
Register 16: PLL Frequency 0 (PLLFREQ0), offset 0x160
This register always contains the current M value presented to the system PLL.
The PLL frequency can be calculated using the following equation:
PLL frequency = (XTAL frequency * MDIV) / ((Q + 1) * (N + 1))
where
MDIV = MINT + (MFRAC / 1024)
The Q and N values are shown in the PLLFREQ1 register. Table 23-14 on page 1269 shows the M,
Q, and N values as well as the resulting PLL frequency for the various XTAL configurations.
PLL Frequency 0 (PLLFREQ0)
Base 0x400F.E000
Offset 0x160
Type RO, reset 0x0000.0032
31
30
29
28
27
26
25
24
23
22
21
20
19
18
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
MFRAC
Type
Reset
RO
1
RO
1
RO
0
RO
0
17
16
MFRAC
RO
0
RO
0
RO
0
RO
0
RO
0
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
MINT
RO
1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:20
reserved
RO
0x000
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
19:10
MFRAC
RO
0x32
PLL M Fractional Value
This field contains the integer value of the PLL M value.
9:0
MINT
RO
0x00
PLL M Integer Value
This field contains the integer value of the PLL M value.
262
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 17: PLL Frequency 1 (PLLFREQ1), offset 0x164
This register always contains the current Q and N values presented to the system PLL.
The M value is shown in the PLLFREQ0 register. Table 23-14 on page 1269 shows the M, Q, and N
values as well as the resulting PLL frequency for the various XTAL configurations.
PLL Frequency 1 (PLLFREQ1)
Base 0x400F.E000
Offset 0x164
Type RO, reset 0x0000.0001
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
6
5
4
3
2
1
0
RO
0
RO
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
14
13
12
11
10
9
8
7
15
reserved
Type
Reset
RO
0
RO
0
Q
RO
0
RO
0
RO
0
RO
0
reserved
RO
0
Bit/Field
Name
Type
Reset
31:13
reserved
RO
0x0000.0
12:8
Q
RO
0x0
RO
0
RO
0
RO
0
N
RO
0
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PLL Q Value
This field contains the PLL Q value.
7:5
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
4:0
N
RO
0x1
PLL N Value
This field contains the PLL N value.
July 17, 2013
263
Texas Instruments-Production Data
System Control
Register 18: PLL Status (PLLSTAT), offset 0x168
This register shows the direct status of the PLL lock.
PLL Status (PLLSTAT)
Base 0x400F.E000
Offset 0x168
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0x0000.000
0
LOCK
RO
0x0
RO
0
LOCK
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PLL Lock
Value Description
1
The PLL powered and locked.
0
The PLL is unpowered or is not yet locked.
264
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 19: Sleep Power Configuration (SLPPWRCFG), offset 0x188
This register provides configuration information for the power control of the SRAM and Flash memory
while in Sleep mode.
Sleep Power Configuration (SLPPWRCFG)
Base 0x400F.E000
Offset 0x188
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
R/W
0
RO
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
FLASHPM
Bit/Field
Name
Type
Reset
31:6
reserved
RO
0x0000.00
5:4
FLASHPM
R/W
0x0
R/W
0
reserved
RO
0
SRAMPM
R/W
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Flash Power Modes
Value Description
0x0
Active Mode
Flash memory is not placed in a lower power mode. This mode
provides the fastest time to sleep and wakeup but the highest
power consumption while the microcontroller is in Sleep mode.
0x1
Reserved
0x2
Low Power Mode
Flash memory is placed in low power mode. This mode provides
the lowers power consumption but requires more time to come
out of Sleep mode.
0x3
3:2
reserved
RO
0x0
Reserved
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
265
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
1:0
SRAMPM
R/W
0x0
Description
SRAM Power Modes
This field controls the low power modes of the on-chip SRAM while the
microcontroller is in Deep-Sleep mode.
Value Description
0x0
Active Mode
SRAM is not placed in a lower power mode. This mode provides
the fastest time to sleep and wakeup but the highest power
consumption while the microcontroller is in Sleep mode.
0x1
Standby Mode
SRAM is place in standby mode while in Sleep mode.
0x2
Reserved
0x3
Low Power Mode
SRAM is placed in low power mode. This mode provides the
slowest time to sleep and wakeup but the lowest power
consumption while in Sleep mode.
266
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 20: Deep-Sleep Power Configuration (DSLPPWRCFG), offset 0x18C
This register provides configuration information for the power control of the SRAM and Flash memory
while in Deep-Sleep mode.
Deep-Sleep Power Configuration (DSLPPWRCFG)
Base 0x400F.E000
Offset 0x18C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
R/W
0
RO
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
FLASHPM
Bit/Field
Name
Type
Reset
31:6
reserved
RO
0x0000.00
5:4
FLASHPM
R/W
0x0
R/W
0
reserved
RO
0
SRAMPM
R/W
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Flash Power Modes
Value Description
0x0
Active Mode
Flash memory is not placed in a lower power mode. This mode
provides the fastest time to sleep and wakeup but the highest
power consumption while the microcontroller is in Deep-Sleep
mode.
0x1
Reserved
0x2
Low Power Mode
Flash memory is placed in low power mode. This mode provides
the lowers power consumption but requires more time to come
out of Deep-Sleep mode.
0x3
3:2
reserved
RO
0x0
Reserved
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
267
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
1:0
SRAMPM
R/W
0x0
Description
SRAM Power Modes
This field controls the low power modes of the on-chip SRAM while the
microcontroller is in Deep-Sleep mode.
Value Description
0x0
Active Mode
SRAM is not placed in a lower power mode. This mode provides
the fastest time to sleep and wakeup but the highest power
consumption while the microcontroller is in Deep-Sleep mode.
0x1
Standby Mode
SRAM is place in standby mode while in Deep-Sleep mode.
0x2
Reserved
0x3
Low Power Mode
SRAM is placed in low power mode. This mode provides the
slowest time to sleep and wakeup but the lowest power
consumption while in Deep-Sleep mode.
268
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 21: LDO Sleep Power Control (LDOSPCTL), offset 0x1B4
This register specifies the LDO output voltage while in Sleep mode. Writes to the VLDO bit field have
no effect on the LDO output voltage, regardless of what is specified for the VADJEN bit. The LDO
output voltage is fixed at the recommended factory reset value.
The table below shows the maximum system clock frequency and PIOSC frequency with respect
to the configured LDO voltage.
Operating Voltage (LDO)
Maximum System Clock Frequency
PIOSC
1.2
80 MHz
16 MHz
0.9
20 MHz
16 MHz
Note:
■ The LDO will not automatically adjust in Sleep/Deepsleep mode if a debugger has been
connected since the last power-on reset.
■ If the LDO voltage is adjusted, it will take an extra 4 us to wake up from Sleep or
Deep-sleep mode.
LDO Sleep Power Control (LDOSPCTL)
Base 0x400F.E000
Offset 0x1B4
Type R/W, reset 0x0000.0018
31
30
29
28
27
26
25
24
22
21
20
19
18
17
16
R/W
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
R/W
0
R/W
1
R/W
1
R/W
0
R/W
0
R/W
0
VADJEN
Type
Reset
23
reserved
reserved
Type
Reset
VLDO
RO
0
Bit/Field
Name
Type
Reset
31
VADJEN
R/W
0
Description
Voltage Adjust Enable
This bit enables the value of the VLDO field to be used to specify the
output voltage of the LDO in Sleep mode.
Value Description
30:8
reserved
RO
0x000.00
0
The LDO output voltage is set to the factory default value in
Sleep mode. The value of the VLDO field does not affect the
LDO operation.
1
The LDO output value in Sleep mode is configured by the value
in the VLDO field.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
269
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
Description
7:0
VLDO
R/W
0x18
LDO Output Voltage
This field provides program control of the LDO output voltage in Run
mode. The value of the field is only used for the LDO voltage when the
VADJEN bit is set.
For lowest power in Sleep mode, it is recommended to configure an
LDO output voltage that is equal to or lower than the default value of
1.2 V.
Value
Description
0x12
0.90 V
0x13
0.95 V
0x14
1.00 V
0x15
1.05 V
0x16
1.10 V
0x17
1.15 V
0x18
1.20 V
0x19 - 0xFF reserved
270
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 22: LDO Sleep Power Calibration (LDOSPCAL), offset 0x1B8
This register provides factory determined values that are recommended for the VLDO field in the
LDOSPCTL register while in Sleep mode.
LDO Sleep Power Calibration (LDOSPCAL)
Base 0x400F.E000
Offset 0x1B8
Type RO, reset 0x0000.1818
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
1
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
RO
0
RO
0
RO
0
reserved
Type
Reset
WITHPLL
Type
Reset
NOPLL
RO
1
Bit/Field
Name
Type
Reset
Description
31:16
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
15:8
WITHPLL
RO
0x18
Sleep with PLL
The value in this field is the suggested value for the VLDO field in the
LDOSPCTL register when using the PLL. This value provides the lowest
recommended LDO output voltage for use with the PLL at the maximum
specified value.
7:0
NOPLL
RO
0x18
Sleep without PLL
The value in this field is the suggested value for the VLDO field in the
LDOSPCTL register when not using the PLL. This value provides the
lowest recommended LDO output voltage for use without the PLL.
July 17, 2013
271
Texas Instruments-Production Data
System Control
Register 23: LDO Deep-Sleep Power Control (LDODPCTL), offset 0x1BC
This register specifies the LDO output voltage while in Deep-Sleep mode. Writes to the VLDO bit
field have no effect on the LDO output voltage, regardless of what is specified for the VADJEN bit.
The LDO output voltage is fixed at the recommended factory reset value.
The table below shows the maximum system clock frequency and PIOSC frequency with respect
to the configured LDO voltage.
Operating Voltage (LDO)
Maximum System Clock Frequency
PIOSC
1.2
80 MHz
16 MHz
0.9
20 MHz
16 MHz
Note:
■ The LDO will not automatically adjust in Sleep/Deepsleep mode if a debugger has been
connected since the last power-on reset.
■ If the LDO voltage is adjusted, it will take an extra 4 us to wake up from Sleep or
Deep-sleep mode.
LDO Deep-Sleep Power Control (LDODPCTL)
Base 0x400F.E000
Offset 0x1BC
Type R/W, reset 0x0000.0012
31
30
29
28
27
26
25
24
22
21
20
19
18
17
16
R/W
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
R/W
0
R/W
1
R/W
0
R/W
0
R/W
1
R/W
0
VADJEN
Type
Reset
23
reserved
reserved
Type
Reset
VLDO
RO
0
Bit/Field
Name
Type
Reset
31
VADJEN
R/W
0
Description
Voltage Adjust Enable
This bit enables the value of the VLDO field to be used to specify the
output voltage of the LDO in Deep-Sleep mode.
Value Description
30:8
reserved
RO
0x000.00
0
The LDO output voltage is set to the factory default value in
Deep-Sleep mode. The value of the VLDO field does not affect
the LDO operation.
1
The LDO output value in Deep-Sleep mode is configured by the
value in the VLDO field.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
272
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
Description
7:0
VLDO
R/W
0x12
LDO Output Voltage
This field provides program control of the LDO output voltage in Run
mode. The value of the field is only used for the LDO voltage when the
VADJEN bit is set.
For lowest power in Deep-sleep mode, it is recommended to configure
the LDO output voltage to the default value of 0.90 V.
Value
Description
0x12
0.90 V
0x13
0.95 V
0x14
1.00 V
0x15
1.05 V
0x16
1.10 V
0x17
1.15 V
0x18
1.20 V
0x19 - 0xFF reserved
July 17, 2013
273
Texas Instruments-Production Data
System Control
Register 24: LDO Deep-Sleep Power Calibration (LDODPCAL), offset 0x1C0
This register provides factory determined values that are recommended for the VLDO field in the
LDODPCTL register while in Deep-Sleep mode.
LDO Deep-Sleep Power Calibration (LDODPCAL)
Base 0x400F.E000
Offset 0x1C0
Type RO, reset 0x0000.1212
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
1
RO
0
RO
0
RO
1
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
0
RO
0
RO
1
RO
0
reserved
Type
Reset
NOPLL
Type
Reset
30KHZ
Bit/Field
Name
Type
Reset
Description
31:16
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
15:8
NOPLL
RO
0x12
Deep-Sleep without PLL
The value in this field is the suggested value for the VLDO field in the
LDODPCTL register when not using the PLL. This value provides the
lowest recommended LDO output voltage for use with the system clock.
7:0
30KHZ
RO
0x12
Deep-Sleep with IOSC
The value in this field is the suggested value for the VLDO field in the
LDODPCTL register when not using the PLL. This value provides the
lowest recommended LDO output voltage for use with the low-frequency
internal oscillator.
274
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 25: Sleep / Deep-Sleep Power Mode Status (SDPMST), offset 0x1CC
This register provides status information on the Sleep and Deep-Sleep power modes as well as
some real time status that can be viewed by a debugger or the core if it is running. These events
do not trigger an interrupt and are meant to provide information that can help tune software for power
management. The status register gets written at the beginning of every Dynamic Power Management
event request with the results of any error checking. There is no mechanism to clear the bits; they
are overwritten on the next event. The LDOUA, FLASHLP, LOWPWR, PRACT bits provide real time
data and there are no events to register that information.
Sleep / Deep-Sleep Power Mode Status (SDPMST)
Base 0x400F.E000
Offset 0x1CC
Type RO, reset 0x0000.0000
31
30
29
28
27
26
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
RO
0
RO
0
RO
0
RO
0
25
24
23
22
21
20
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
reserved
Type
Reset
PPDW
RO
0
18
17
16
LDOUA FLASHLP LOWPWR PRACT
reserved
Type
Reset
19
RO
0
LMAXERR reserved LSMINERR LDMINERR PPDERR FPDERR SPDERR
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:20
reserved
RO
0x000
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
19
LDOUA
RO
0
LDO Update Active
Value Description
18
FLASHLP
RO
0
1
The LDO voltage level is changing.
0
The LDO voltage level is not changing.
Flash Memory in Low Power State
Value Description
17
LOWPWR
RO
0
1
The Flash memory is currently in the low power state as
programmed in the SLPPWRCFG or DSLPPWRCFG register.
0
The Flash memory is currently in the active state.
Sleep or Deep-Sleep Mode
Value Description
1
The microcontroller is currently in Sleep or Deep-Sleep mode
and is waiting for an interrupt or is in the process of powering
up. The status of this bit is not affected by the power state of
the Flash memory or SRAM.
0
The microcontroller is currently in Run mode.
July 17, 2013
275
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
16
PRACT
RO
0
Description
Sleep or Deep-Sleep Power Request Active
Value Description
15:8
reserved
RO
0x00
7
PPDW
RO
0
1
The microcontroller is currently in Deep-sleep mode or is in
Sleep mode and a request to put the SRAM and/or Flash
memory into a lower power mode is currently active as
configured by the the SLPPWRCFG register.
0
A power request is not active.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PIOSC Power Down Request Warning
Value Description
6
LMAXERR
RO
0
1
A warning has occurred because software has requested that
the PIOSC be powered down during Deep-Sleep using the
PIOSCPD bit in the DSLPCLKCFG register and a peripheral
requires that it be active in Deep-Sleep. The PIOSC is powered
down regardless of the warning.
0
No error.
VLDO Value Above Maximum Error
Value Description
1
An error has occurred because software has requested that the
LDO voltage be above the maximum value allowed using the
VLDO bit in the LDOSPCTL or LDODPCTL register.
In this situation, the LDO is set to the factory default value.
0
No error.
5
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
4
LSMINERR
RO
0
VLDO Value Below Minimum Error in Sleep Mode
Value Description
1
An error has occurred because software has requested that the
LDO voltage be below the minimum value allowed using the
VLDO bit in the LDOSPCTL register.
In this situation, the LDO voltage is not changed when entering
Sleep mode.
0
No error.
276
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
3
LDMINERR
RO
0
Description
VLDO Value Below Minimum Error in Deep-Sleep Mode
Value Description
1
An error has occurred because software has requested that the
LDO voltage be below the minimum value allowed using the
VLDO bit in the LDODPCTL register.
In this situation, the LDO voltage is not changed when entering
Deep-sleep mode.
0
2
PPDERR
RO
0
No error.
PIOSC Power Down Request Error
Value Description
1
An error has occurred because software has requested that the
PIOSC be powered down during Deep-Sleep and it is not
possible to power down the PIOSC.
In this situation, the PIOSC is not powered down when entering
Deep-sleep mode.
0
1
FPDERR
RO
0
No error.
Flash Memory Power Down Request Error
Value Description
0
SPDERR
RO
0
1
An error has occurred because software has requested a Flash
memory power down mode that is not available using the
FLASHPM field in the SLPPWRCFG or the DSLPPWRCFG
register.
0
No error.
SRAM Power Down Request Error
Value Description
1
An error has occurred because software has requested an
SRAM power down mode that is not available using the SRAMPM
field in the SLPPWRCFG or the DSLPPWRCFG register.
0
No error.
July 17, 2013
277
Texas Instruments-Production Data
System Control
Register 26: Watchdog Timer Peripheral Present (PPWD), offset 0x300
The PPWD register provides software information regarding the watchdog modules.
Important: This register should be used to determine which watchdog timers are implemented on
this microcontroller. However, to support legacy software, the DC1 register is available.
A read of the DC1 register correctly identifies if a legacy module is present.
Watchdog Timer Peripheral Present (PPWD)
Base 0x400F.E000
Offset 0x300
Type RO, reset 0x0000.0003
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
P1
P0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:2
reserved
RO
0
1
P1
RO
0x1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Watchdog Timer 1 Present
Value Description
0
P0
RO
0x1
1
Watchdog module 1 is present.
0
Watchdog module 1 is not present.
Watchdog Timer 0 Present
Value Description
1
Watchdog module 0 is present.
0
Watchdog module 0 is not present.
278
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 27: 16/32-Bit General-Purpose Timer Peripheral Present (PPTIMER),
offset 0x304
The PPTIMER register provides software information regarding the 16/32-bit general-purpose timer
modules.
Important: This register should be used to determine which timers are implemented on this
microcontroller. However, to support legacy software, the DC2 register is available. A
read of the DC2 register correctly identifies if a legacy module is present. Software must
use this register to determine if a module that is not supported by the DC2 register is
present.
16/32-Bit General-Purpose Timer Peripheral Present (PPTIMER)
Base 0x400F.E000
Offset 0x304
Type RO, reset 0x0000.003F
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:6
reserved
RO
0
5
P5
RO
0x1
RO
0
RO
0
RO
0
5
4
3
2
1
0
P5
P4
P3
P2
P1
P0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
16/32-Bit General-Purpose Timer 5 Present
Value Description
4
P4
RO
0x1
1
16/32-bit general-purpose timer module 5 is present.
0
16/32-bit general-purpose timer module 6 is not present.
16/32-Bit General-Purpose Timer 4 Present
Value Description
3
P3
RO
0x1
1
16/32-bit general-purpose timer module 4 is present.
0
16/32-bit general-purpose timer module 4 is not present.
16/32-Bit General-Purpose Timer 3 Present
Value Description
1
16/32-bit general-purpose timer module 3 is present.
0
16/32-bit general-purpose timer module 3 is not present.
July 17, 2013
279
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
2
P2
RO
0x1
Description
16/32-Bit General-Purpose Timer 2 Present
Value Description
1
P1
RO
0x1
1
16/32-bit general-purpose timer module 2 is present.
0
16/32-bit general-purpose timer module 2 is not present.
16/32-Bit General-Purpose Timer 1 Present
Value Description
0
P0
RO
0x1
1
16/32-bit general-purpose timer module 1 is present.
0
16/32-bit general-purpose timer module 1 is not present.
16/32-Bit General-Purpose Timer 0 Present
Value Description
1
16/32-bit general-purpose timer module 0 is present.
0
16/32-bit general-purpose timer module 0 is not present.
280
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 28: General-Purpose Input/Output Peripheral Present (PPGPIO),
offset 0x308
The PPGPIO register provides software information regarding the general-purpose input/output
modules.
Important: This register should be used to determine which GPIO ports are implemented on this
microcontroller. However, to support legacy software, the DC4 register is available. A
read of the DC4 register correctly identifies if a legacy module is present. Software must
use this register to determine if a module that is not supported by the DC4 register is
present.
General-Purpose Input/Output Peripheral Present (PPGPIO)
Base 0x400F.E000
Offset 0x308
Type RO, reset 0x0000.03FF
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
reserved
P14
P13
P12
P11
P10
P9
P8
P7
P6
P5
P4
P3
P2
P1
P0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Bit/Field
Name
Type
Reset
31:15
reserved
RO
0
14
P14
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
GPIO Port Q Present
Value Description
13
P13
RO
0x0
1
GPIO Port Q is present.
0
GPIO Port Q is not present.
GPIO Port P Present
Value Description
12
P12
RO
0x0
1
GPIO Port P is present.
0
GPIO Port P is not present.
GPIO Port N Present
Value Description
1
GPIO Port N is present.
0
GPIO Port N is not present.
July 17, 2013
281
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
11
P11
RO
0x0
Description
GPIO Port M Present
Value Description
10
P10
RO
0x0
1
GPIO Port M is present.
0
GPIO Port M is not present.
GPIO Port L Present
Value Description
9
P9
RO
0x1
1
GPIO Port L is present.
0
GPIO Port L is not present.
GPIO Port K Present
Value Description
8
P8
RO
0x1
1
GPIO Port K is present.
0
GPIO Port K is not present.
GPIO Port J Present
Value Description
7
P7
RO
0x1
1
GPIO Port J is present.
0
GPIO Port J is not present.
GPIO Port H Present
Value Description
6
P6
RO
0x1
1
GPIO Port H is present.
0
GPIO Port H is not present.
GPIO Port G Present
Value Description
5
P5
RO
0x1
1
GPIO Port G is present.
0
GPIO Port G is not present.
GPIO Port F Present
Value Description
1
GPIO Port F is present.
0
GPIO Port F is not present.
282
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
4
P4
RO
0x1
Description
GPIO Port E Present
Value Description
3
P3
RO
0x1
1
GPIO Port E is present.
0
GPIO Port E is not present.
GPIO Port D Present
Value Description
2
P2
RO
0x1
1
GPIO Port D is present.
0
GPIO Port D is not present.
GPIO Port C Present
Value Description
1
P1
RO
0x1
1
GPIO Port C is present.
0
GPIO Port C is not present.
GPIO Port B Present
Value Description
0
P0
RO
0x1
1
GPIO Port B is present.
0
GPIO Port B is not present.
GPIO Port A Present
Value Description
1
GPIO Port A is present.
0
GPIO Port A is not present.
July 17, 2013
283
Texas Instruments-Production Data
System Control
Register 29: Micro Direct Memory Access Peripheral Present (PPDMA), offset
0x30C
The PPDMA register provides software information regarding the μDMA module.
Important: This register should be used to determine if the μDMA module is implemented on this
microcontroller. However, to support legacy software, the DC7 register is available. A
read of the DC7 register correctly identifies if the μDMA module is present.
Micro Direct Memory Access Peripheral Present (PPDMA)
Base 0x400F.E000
Offset 0x30C
Type RO, reset 0x0000.0001
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0
0
P0
RO
0x1
RO
0
0
P0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
μDMA Module Present
Value Description
1
μDMA module is present.
0
μDMA module is not present.
284
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 30: Hibernation Peripheral Present (PPHIB), offset 0x314
The PPHIB register provides software information regarding the Hibernation module.
Important: This register should be used to determine if the Hibernation module is implemented on
this microcontroller. However, to support legacy software, the DC1 register is available.
A read of the DC1 register correctly identifies if the Hibernation module is present.
Hibernation Peripheral Present (PPHIB)
Base 0x400F.E000
Offset 0x314
Type RO, reset 0x0000.0001
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0
0
P0
RO
0x1
RO
0
P0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Hibernation Module Present
Value Description
1
Hibernation module is present.
0
Hibernation module is not present.
July 17, 2013
285
Texas Instruments-Production Data
System Control
Register 31: Universal Asynchronous Receiver/Transmitter Peripheral Present
(PPUART), offset 0x318
The PPUART register provides software information regarding the UART modules.
Important: This register should be used to determine which UART modules are implemented on
this microcontroller. However, to support legacy software, the DC2 register is available.
A read of the DC2 register correctly identifies if a legacy UART module is present.
Software must use this register to determine if a module that is not supported by the
DC2 register is present.
Universal Asynchronous Receiver/Transmitter Peripheral Present (PPUART)
Base 0x400F.E000
Offset 0x318
Type RO, reset 0x0000.00FF
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:8
reserved
RO
0
7
P7
RO
0x1
RO
0
RO
0
7
6
5
4
3
2
1
0
P7
P6
P5
P4
P3
P2
P1
P0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
UART Module 7 Present
Value Description
6
P6
RO
0x1
1
UART module 7 is present.
0
UART module 7 is not present.
UART Module 6 Present
Value Description
5
P5
RO
0x1
1
UART module 6 is present.
0
UART module 6 is not present.
UART Module 5 Present
Value Description
1
UART module 5 is present.
0
UART module 5 is not present.
286
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
4
P4
RO
0x1
Description
UART Module 4 Present
Value Description
3
P3
RO
0x1
1
UART module 4 is present.
0
UART module 4 is not present.
UART Module 3 Present
Value Description
2
P2
RO
0x1
1
UART module 3 is present.
0
UART module 3 is not present.
UART Module 2 Present
Value Description
1
P1
RO
0x1
1
UART module 2 is present.
0
UART module 2 is not present.
UART Module 1 Present
Value Description
0
P0
RO
0x1
1
UART module 1 is present.
0
UART module 1 is not present.
UART Module 0 Present
Value Description
1
UART module 0 is present.
0
UART module 0 is not present.
July 17, 2013
287
Texas Instruments-Production Data
System Control
Register 32: Synchronous Serial Interface Peripheral Present (PPSSI), offset
0x31C
The PPSSI register provides software information regarding the SSI modules.
Important: This register should be used to determine which SSI modules are implemented on this
microcontroller. However, to support legacy software, the DC2 register is available. A
read of the DC2 register correctly identifies if a legacy SSI module is present. Software
must use this register to determine if a module that is not supported by the DC2 register
is present.
Synchronous Serial Interface Peripheral Present (PPSSI)
Base 0x400F.E000
Offset 0x31C
Type RO, reset 0x0000.000F
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:4
reserved
RO
0
3
P3
RO
0x1
RO
0
RO
0
RO
0
RO
0
RO
0
3
2
1
0
P3
P2
P1
P0
RO
1
RO
1
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
SSI Module 3 Present
Value Description
2
P2
RO
0x1
1
SSI module 3 is present.
0
SSI module 3 is not present.
SSI Module 2 Present
Value Description
1
P1
RO
0x1
1
SSI module 2 is present.
0
SSI module 2 is not present.
SSI Module 1 Present
Value Description
1
SSI module 1 is present.
0
SSI module 1 is not present.
288
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
0
P0
RO
0x1
Description
SSI Module 0 Present
Value Description
1
SSI module 0 is present.
0
SSI module 0 is not present.
July 17, 2013
289
Texas Instruments-Production Data
System Control
Register 33: Inter-Integrated Circuit Peripheral Present (PPI2C), offset 0x320
The PPI2C register provides software information regarding the I2C modules.
Important: This register should be used to determine which I2C modules are implemented on this
microcontroller. However, to support legacy software, the DC2 register is available. A
read of the DC2 register correctly identifies if a legacy I2C module is present. Software
must use this register to determine if a module that is not supported by the DC2 register
is present.
Inter-Integrated Circuit Peripheral Present (PPI2C)
Base 0x400F.E000
Offset 0x320
Type RO, reset 0x0000.003F
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:6
reserved
RO
0
5
P5
RO
0x1
RO
0
RO
0
RO
0
5
4
3
2
1
0
P5
P4
P3
P2
P1
P0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2C Module 5 Present
Value Description
4
P4
RO
0x1
1
I2C module 5 is present.
0
I2C module 5 is not present.
I2C Module 4 Present
Value Description
3
P3
RO
0x1
1
I2C module 4 is present.
0
I2C module 4 is not present.
I2C Module 3 Present
Value Description
1
I2C module 3 is present.
0
I2C module 3 is not present.
290
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
2
P2
RO
0x1
Description
I2C Module 2 Present
Value Description
1
P1
RO
0x1
1
I2C module 2 is present.
0
I2C module 2 is not present.
I2C Module 1 Present
Value Description
0
P0
RO
0x1
1
I2C module 1 is present.
0
I2C module 1 is not present.
I2C Module 0 Present
Value Description
1
I2C module 0 is present.
0
I2C module 0 is not present.
July 17, 2013
291
Texas Instruments-Production Data
System Control
Register 34: Universal Serial Bus Peripheral Present (PPUSB), offset 0x328
The PPUSB register provides software information regarding the USB module.
Important: This register should be used to determine if the USB module is implemented on this
microcontroller. However, to support legacy software, the DC6 register is available. A
read of the DC6 register correctly identifies if the USB module is present.
Universal Serial Bus Peripheral Present (PPUSB)
Base 0x400F.E000
Offset 0x328
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0
0
P0
RO
0x0
RO
0
P0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
USB Module Present
Value Description
1
USB module is present.
0
USB module is not present.
292
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 35: Controller Area Network Peripheral Present (PPCAN), offset 0x334
The PPCAN register provides software information regarding the CAN modules.
Important: This register should be used to determine which CAN modules are implemented on
this microcontroller. However, to support legacy software, the DC1 register is available.
A read of the DC1 register correctly identifies if a legacy CAN module is present.
Controller Area Network Peripheral Present (PPCAN)
Base 0x400F.E000
Offset 0x334
Type RO, reset 0x0000.0003
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
P1
P0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:2
reserved
RO
0
1
P1
RO
0x1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
CAN Module 1 Present
Value Description
0
P0
RO
0x1
1
CAN module 1 is present.
0
CAN module 1 is not present.
CAN Module 0 Present
Value Description
1
CAN module 0 is present.
0
CAN module 0 is not present.
July 17, 2013
293
Texas Instruments-Production Data
System Control
Register 36: Analog-to-Digital Converter Peripheral Present (PPADC), offset
0x338
The PPADC register provides software information regarding the ADC modules.
Important: This register should be used to determine which ADC modules are implemented on
this microcontroller. However, to support legacy software, the DC1 register is available.
A read of the DC1 register correctly identifies if a legacy ADC module is present.
Analog-to-Digital Converter Peripheral Present (PPADC)
Base 0x400F.E000
Offset 0x338
Type RO, reset 0x0000.0003
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:2
reserved
RO
0
1
P1
RO
0x1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
P1
P0
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
ADC Module 1 Present
Value Description
0
P0
RO
0x1
1
ADC module 1 is present.
0
ADC module 1 is not present.
ADC Module 0 Present
Value Description
1
ADC module 0 is present.
0
ADC module 0 is not present.
294
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 37: Analog Comparator Peripheral Present (PPACMP), offset 0x33C
The PPACMP register provides software information regarding the analog comparator module.
Important: This register should be used to determine if the analog comparator module is
implemented on this microcontroller. However, to support legacy software, the DC2
register is available. A read of the DC2 register correctly identifies if the analog
comparator module is present.
Note that the Analog Comparator Peripheral Properties (ACMPPP) register indicates
how many analog comparator blocks are included in the module.
Analog Comparator Peripheral Present (PPACMP)
Base 0x400F.E000
Offset 0x33C
Type RO, reset 0x0000.0001
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0
0
P0
RO
0x1
RO
0
0
P0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Analog Comparator Module Present
Value Description
1
Analog comparator module is present.
0
Analog comparator module is not present.
July 17, 2013
295
Texas Instruments-Production Data
System Control
Register 38: Pulse Width Modulator Peripheral Present (PPPWM), offset 0x340
The PPPWM register provides software information regarding the PWM modules.
Important: This register should be used to determine which PWM modules are implemented on
this microcontroller. However, to support legacy software, the DC1 register is available.
A read of the DC1 register correctly identifies if the legacy PWM module is present.
Software must use this register to determine if a module that is not supported by the
DC1 register is present.
Pulse Width Modulator Peripheral Present (PPPWM)
Base 0x400F.E000
Offset 0x340
Type RO, reset 0x0000.0003
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
P1
P0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:2
reserved
RO
0
1
P1
RO
0x1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PWM Module 1 Present
Value Description
0
P0
RO
0x1
1
PWM module 1 is present.
0
PWM module 1 is not present.
PWM Module 0 Present
Value Description
1
PWM module 0 is present.
0
PWM module 0 is not present.
296
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 39: Quadrature Encoder Interface Peripheral Present (PPQEI), offset
0x344
The PPQEI register provides software information regarding the QEI modules.
Important: This register should be used to determine which QEI modules are implemented on this
microcontroller. However, to support legacy software, the DC2 register is available. A
read of the DC2 register correctly identifies if a legacy QEI module is present.
Quadrature Encoder Interface Peripheral Present (PPQEI)
Base 0x400F.E000
Offset 0x344
Type RO, reset 0x0000.0003
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:2
reserved
RO
0
1
P1
RO
0x1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
P1
P0
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
QEI Module 1 Present
Value Description
0
P0
RO
0x1
1
QEI module 1 is present.
0
QEI module 1 is not present.
QEI Module 0 Present
Value Description
1
QEI module 0 is present.
0
QEI module 0 is not present.
July 17, 2013
297
Texas Instruments-Production Data
System Control
Register 40: EEPROM Peripheral Present (PPEEPROM), offset 0x358
The PPEEPROM register provides software information regarding the EEPROM module.
EEPROM Peripheral Present (PPEEPROM)
Base 0x400F.E000
Offset 0x358
Type RO, reset 0x0000.0001
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0
0
P0
RO
0x1
RO
0
P0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
EEPROM Module Present
Value Description
1
EEPROM module is present.
0
EEPROM module is not present.
298
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 41: 32/64-Bit Wide General-Purpose Timer Peripheral Present
(PPWTIMER), offset 0x35C
The PPWTIMER register provides software information regarding the 32/64-bit wide general-purpose
timer modules.
32/64-Bit Wide General-Purpose Timer Peripheral Present (PPWTIMER)
Base 0x400F.E000
Offset 0x35C
Type RO, reset 0x0000.003F
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:6
reserved
RO
0
5
P5
RO
0x1
RO
0
RO
0
RO
0
5
4
3
2
1
0
P5
P4
P3
P2
P1
P0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
32/64-Bit Wide General-Purpose Timer 5 Present
Value Description
4
P4
RO
0x1
1
32/64-bit wide general-purpose timer module 5 is present.
0
32/64-bit wide general-purpose timer module 5 is not present.
32/64-Bit Wide General-Purpose Timer 4 Present
Value Description
3
P3
RO
0x1
1
32/64-bit wide general-purpose timer module 4 is present.
0
32/64-bit wide general-purpose timer module 4 is not present.
32/64-Bit Wide General-Purpose Timer 3 Present
Value Description
2
P2
RO
0x1
1
32/64-bit wide general-purpose timer module 3 is present.
0
32/64-bit wide general-purpose timer module 3 is not present.
32/64-Bit Wide General-Purpose Timer 2 Present
Value Description
1
32/64-bit wide general-purpose timer module 2 is present.
0
32/64-bit wide general-purpose timer module 2 is not present.
July 17, 2013
299
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
1
P1
RO
0x1
Description
32/64-Bit Wide General-Purpose Timer 1 Present
Value Description
0
P0
RO
0x1
1
32/64-bit wide general-purpose timer module 1 is present.
0
32/64-bit wide general-purpose timer module 1 is not present.
32/64-Bit Wide General-Purpose Timer 0 Present
Value Description
1
32/64-bit wide general-purpose timer module 0 is present.
0
32/64-bit wide general-purpose timer module 0 is not present.
300
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 42: Watchdog Timer Software Reset (SRWD), offset 0x500
The SRWD register provides software the capability to reset the available watchdog modules. This
register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the watchdog modules and has the same bit polarity as the corresponding SRCRn
bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRWD register. While the SRWD bit is 1, the peripheral is
held in reset.
2. Software completes the reset process by clearing the SRWD bit.
There may be latency from the clearing of the SRWD bit to when the peripheral is ready for use.
Software can check the corresponding PRWD bit to be sure.
Important: This register should be used to reset the watchdog modules. To support legacy software,
the SRCR0 register is available. Setting a bit in the SRCR0 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR0 register can
be read back correctly when reading the SRCR0 register. If software uses this register
to reset a legacy peripheral (such as Watchdog 1), the write causes proper operation,
but the value of that bit is not reflected in the SRCR0 register. If software uses both
legacy and peripheral-specific register accesses, the peripheral-specific registers must
be accessed by read-modify-write operations that affect only peripherals that are not
present in the legacy registers. In this manner, both the peripheral-specific and legacy
registers have coherent information.
Watchdog Timer Software Reset (SRWD)
Base 0x400F.E000
Offset 0x500
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
R/W
0
Watchdog Timer 1 Software Reset
Value Description
1
Watchdog module 1 is reset.
0
Watchdog module 1 is not reset.
July 17, 2013
301
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
0
R0
R/W
0
Description
Watchdog Timer 0 Software Reset
Value Description
1
Watchdog module 0 is reset.
0
Watchdog module 0 is not reset.
302
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 43: 16/32-Bit General-Purpose Timer Software Reset (SRTIMER),
offset 0x504
The SRTIMER register provides software the capability to reset the available 16/32-bit timer modules.
This register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the timer modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRTIMER register. While the SRTIMER bit is 1, the peripheral
is held in reset.
2. Software completes the reset process by clearing the SRTIMER bit.
There may be latency from the clearing of the SRTIMER bit to when the peripheral is ready for use.
Software can check the corresponding PRTIMER bit to be sure.
Important: This register should be used to reset the timer modules. To support legacy software,
the SRCR1 register is available. Setting a bit in the SRCR1 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR1 register can
be read back correctly when reading the SRCR1 register. Software must use this register
to reset modules that are not present in the legacy registers. If software uses this register
to reset a legacy peripheral (such as Timer 1), the write causes proper operation, but
the value of that bit is not reflected in the SRCR1 register. If software uses both legacy
and peripheral-specific register accesses, the peripheral-specific registers must be
accessed by read-modify-write operations that affect only peripherals that are not present
in the legacy registers. In this manner, both the peripheral-specific and legacy registers
have coherent information.
16/32-Bit General-Purpose Timer Software Reset (SRTIMER)
Base 0x400F.E000
Offset 0x504
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
R/W
0
16/32-Bit General-Purpose Timer 5 Software Reset
Value Description
1
16/32-bit general-purpose timer module 5 is reset.
0
16/32-bit general-purpose timer module 5 is not reset.
July 17, 2013
303
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
4
R4
R/W
0
Description
16/32-Bit General-Purpose Timer 4 Software Reset
Value Description
3
R3
R/W
0
1
16/32-bit general-purpose timer module 4 is reset.
0
16/32-bit general-purpose timer module 4 is not reset.
16/32-Bit General-Purpose Timer 3 Software Reset
Value Description
2
R2
R/W
0
1
16/32-bit general-purpose timer module 3 is reset.
0
16/32-bit general-purpose timer module 3 is not reset.
16/32-Bit General-Purpose Timer 2 Software Reset
Value Description
1
R1
R/W
0
1
16/32-bit general-purpose timer module 2 is reset.
0
16/32-bit general-purpose timer module 2 is not reset.
16/32-Bit General-Purpose Timer 1 Software Reset
Value Description
0
R0
R/W
0
1
16/32-bit general-purpose timer module 1 is reset.
0
16/32-bit general-purpose timer module 1 is not reset.
16/32-Bit General-Purpose Timer 0 Software Reset
Value Description
1
16/32-bit general-purpose timer module 0 is reset.
0
16/32-bit general-purpose timer module 0 is not reset.
304
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 44: General-Purpose Input/Output Software Reset (SRGPIO), offset
0x508
The SRGPIO register provides software the capability to reset the available GPIO modules. This
register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the GPIO modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRGPIO register. While the SRGPIO bit is 1, the peripheral
is held in reset.
2. Software completes the reset process by clearing the SRGPIO bit.
There may be latency from the clearing of the SRGPIO bit to when the peripheral is ready for use.
Software can check the corresponding PRGPIO bit to be sure.
Important: This register should be used to reset the GPIO modules. To support legacy software,
the SRCR2 register is available. Setting a bit in the SRCR2 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR2 register can
be read back correctly when reading the SRCR2 register. Software must use this register
to reset modules that are not present in the legacy registers. If software uses this register
to reset a legacy peripheral (such as GPIO A), the write causes proper operation, but
the value of that bit is not reflected in the SRCR2 register. If software uses both legacy
and peripheral-specific register accesses, the peripheral-specific registers must be
accessed by read-modify-write operations that affect only peripherals that are not present
in the legacy registers. In this manner, both the peripheral-specific and legacy registers
have coherent information.
General-Purpose Input/Output Software Reset (SRGPIO)
Base 0x400F.E000
Offset 0x508
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
4
3
2
1
0
R9
R8
R7
R6
R5
R4
R3
R2
R1
R0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:10
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
9
R9
R/W
0
GPIO Port K Software Reset
Value Description
1
GPIO Port K is reset.
0
GPIO Port K is not reset.
July 17, 2013
305
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
8
R8
R/W
0
Description
GPIO Port J Software Reset
Value Description
7
R7
R/W
0
1
GPIO Port J is reset.
0
GPIO Port J is not reset.
GPIO Port H Software Reset
Value Description
6
R6
R/W
0
1
GPIO Port H is reset.
0
GPIO Port H is not reset.
GPIO Port G Software Reset
Value Description
5
R5
R/W
0
1
GPIO Port G is reset.
0
GPIO Port G is not reset.
GPIO Port F Software Reset
Value Description
4
R4
R/W
0
1
GPIO Port F is reset.
0
GPIO Port F is not reset.
GPIO Port E Software Reset
Value Description
3
R3
R/W
0
1
GPIO Port E is reset.
0
GPIO Port E is not reset.
GPIO Port D Software Reset
Value Description
2
R2
R/W
0
1
GPIO Port D is reset.
0
GPIO Port D is not reset.
GPIO Port C Software Reset
Value Description
1
GPIO Port C is reset.
0
GPIO Port C is not reset.
306
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
1
R1
R/W
0
Description
GPIO Port B Software Reset
Value Description
0
R0
R/W
0
1
GPIO Port B is reset.
0
GPIO Port B is not reset.
GPIO Port A Software Reset
Value Description
1
GPIO Port A is reset.
0
GPIO Port A is not reset.
July 17, 2013
307
Texas Instruments-Production Data
System Control
Register 45: Micro Direct Memory Access Software Reset (SRDMA), offset
0x50C
The SRDMA register provides software the capability to reset the available μDMA module. This
register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the μDMA module and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRDMA register. While the SRDMA bit is 1, the peripheral is
held in reset.
2. Software completes the reset process by clearing the SRDMA bit.
There may be latency from the clearing of the SRDMA bit to when the peripheral is ready for use.
Software can check the corresponding PRDMA bit to be sure.
Important: This register should be used to reset the μDMA module. To support legacy software,
the SRCR2 register is available. Setting the UDMA bit in the SRCR2 register also resets
the μDMA module. If the UDMA bit is set by writing to the SRCR2 register, it can be read
back correctly when reading the SRCR2 register. If software uses this register to reset
the μDMA module, the write causes proper operation, but the value of the UDMA bit is
not reflected in the SRCR2 register. If software uses both legacy and peripheral-specific
register accesses, the peripheral-specific registers must be accessed by
read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Micro Direct Memory Access Software Reset (SRDMA)
Base 0x400F.E000
Offset 0x50C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
0
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
R/W
0
μDMA Module Software Reset
Value Description
1
μDMA module is reset.
0
μDMA module is not reset.
308
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 46: Hibernation Software Reset (SRHIB), offset 0x514
The SRHIB register provides software the capability to reset the available Hibernation module. This
register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the Hibernation module and has the same bit polarity as the corresponding SRCRn
bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRHIB register. While the SRHIB bit is 1, the peripheral is
held in reset.
2. Software completes the reset process by clearing the SRHIB bit.
There may be latency from the clearing of the SRHIB bit to when the peripheral is ready for use.
Software can check the corresponding PRHIB bit to be sure.
Important: This register should be used to reset the Hibernation module. To support legacy software,
the SRCR0 register is available. Setting the HIB bit in the SRCR0 register also resets
the Hibernation module. If the HIB bit is set by writing to the SRCR0 register, it can be
read back correctly when reading the SRCR0 register. If software uses this register to
reset the Hibernation module, the write causes proper operation, but the value of the
HIB bit is not reflected in the SRCR0 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Hibernation Software Reset (SRHIB)
Base 0x400F.E000
Offset 0x514
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
R0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
R/W
0
Hibernation Module Software Reset
Value Description
1
Hibernation module is reset.
0
Hibernation module is not reset.
July 17, 2013
309
Texas Instruments-Production Data
System Control
Register 47: Universal Asynchronous Receiver/Transmitter Software Reset
(SRUART), offset 0x518
The SRUART register provides software the capability to reset the available UART modules. This
register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the UART modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRUART register. While the SRUART bit is 1, the peripheral
is held in reset.
2. Software completes the reset process by clearing the SRUART bit.
There may be latency from the clearing of the SRUART bit to when the peripheral is ready for use.
Software can check the corresponding PRUART bit to be sure.
Important: This register should be used to reset the UART modules. To support legacy software,
the SRCR1 register is available. Setting a bit in the SRCR1 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR1 register can
be read back correctly when reading the SRCR1 register. Software must use this register
to reset modules that are not present in the legacy registers. If software uses this register
to reset a legacy peripheral (such as UART0), the write causes proper operation, but
the value of that bit is not reflected in the SRCR1 register. If software uses both legacy
and peripheral-specific register accesses, the peripheral-specific registers must be
accessed by read-modify-write operations that affect only peripherals that are not present
in the legacy registers. In this manner, both the peripheral-specific and legacy registers
have coherent information.
Universal Asynchronous Receiver/Transmitter Software Reset (SRUART)
Base 0x400F.E000
Offset 0x518
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
R7
R6
R5
R4
R3
R2
R1
R0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:8
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7
R7
R/W
0
UART Module 7 Software Reset
Value Description
1
UART module 7 is reset.
0
UART module 7 is not reset.
310
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
6
R6
R/W
0
Description
UART Module 6 Software Reset
Value Description
5
R5
R/W
0
1
UART module 6 is reset.
0
UART module 6 is not reset.
UART Module 5 Software Reset
Value Description
4
R4
R/W
0
1
UART module 5 is reset.
0
UART module 5 is not reset.
UART Module 4 Software Reset
Value Description
3
R3
R/W
0
1
UART module 4 is reset.
0
UART module 4 is not reset.
UART Module 3 Software Reset
Value Description
2
R2
R/W
0
1
UART module 3 is reset.
0
UART module 3 is not reset.
UART Module 2 Software Reset
Value Description
1
R1
R/W
0
1
UART module 2 is reset.
0
UART module 2 is not reset.
UART Module 1 Software Reset
Value Description
0
R0
R/W
0
1
UART module 1 is reset.
0
UART module 1 is not reset.
UART Module 0 Software Reset
Value Description
1
UART module 0 is reset.
0
UART module 0 is not reset.
July 17, 2013
311
Texas Instruments-Production Data
System Control
Register 48: Synchronous Serial Interface Software Reset (SRSSI), offset
0x51C
The SRSSI register provides software the capability to reset the available SSI modules. This register
provides the same capability as the legacy Software Reset Control n SRCRn registers specifically
for the SSI modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRSSI register. While the SRSSI bit is 1, the peripheral is
held in reset.
2. Software completes the reset process by clearing the SRSSI bit.
There may be latency from the clearing of the SRSSI bit to when the peripheral is ready for use.
Software can check the corresponding PRSSI bit to be sure.
Important: This register should be used to reset the SSI modules. To support legacy software, the
SRCR1 register is available. Setting a bit in the SRCR1 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR1 register can
be read back correctly when reading the SRCR1 register. Software must use this register
to reset modules that are not present in the legacy registers. If software uses this register
to reset a legacy peripheral (such as SSI0), the write causes proper operation, but the
value of that bit is not reflected in the SRCR1 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Synchronous Serial Interface Software Reset (SRSSI)
Base 0x400F.E000
Offset 0x51C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
3
2
1
0
R3
R2
R1
R0
R/W
0
R/W
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3
R3
R/W
0
SSI Module 3 Software Reset
Value Description
1
SSI module 3 is reset.
0
SSI module 3 is not reset.
312
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
2
R2
R/W
0
Description
SSI Module 2 Software Reset
Value Description
1
R1
R/W
0
1
SSI module 2 is reset.
0
SSI module 2 is not reset.
SSI Module 1 Software Reset
Value Description
0
R0
R/W
0
1
SSI module 1 is reset.
0
SSI module 1 is not reset.
SSI Module 0 Software Reset
Value Description
1
SSI module 0 is reset.
0
SSI module 0 is not reset.
July 17, 2013
313
Texas Instruments-Production Data
System Control
Register 49: Inter-Integrated Circuit Software Reset (SRI2C), offset 0x520
The SRI2C register provides software the capability to reset the available I2C modules. This register
provides the same capability as the legacy Software Reset Control n SRCRn registers specifically
for the I2C modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRI2C register. While the SRI2C bit is 1, the peripheral is
held in reset.
2. Software completes the reset process by clearing the SRI2C bit.
There may be latency from the clearing of the SRI2C bit to when the peripheral is ready for use.
Software can check the corresponding PRI2C bit to be sure.
Important: This register should be used to reset the I2C modules. To support legacy software, the
SRCR1 register is available. Setting a bit in the SRCR1 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR1 register can
be read back correctly when reading the SRCR1 register. Software must use this register
to reset modules that are not present in the legacy registers. If software uses this register
to reset a legacy peripheral (such as I2C0), the write causes proper operation, but the
value of that bit is not reflected in the SRCR1 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Inter-Integrated Circuit Software Reset (SRI2C)
Base 0x400F.E000
Offset 0x520
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
R/W
0
I2C Module 5 Software Reset
Value Description
1
I2C module 5 is reset.
0
I2C module 5 is not reset.
314
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
4
R4
R/W
0
Description
I2C Module 4 Software Reset
Value Description
3
R3
R/W
0
1
I2C module 4 is reset.
0
I2C module 4 is not reset.
I2C Module 3 Software Reset
Value Description
2
R2
R/W
0
1
I2C module 3 is reset.
0
I2C module 3 is not reset.
I2C Module 2 Software Reset
Value Description
1
R1
R/W
0
1
I2C module 2 is reset.
0
I2C module 2 is not reset.
I2C Module 1 Software Reset
Value Description
0
R0
R/W
0
1
I2C module 1 is reset.
0
I2C module 1 is not reset.
I2C Module 0 Software Reset
Value Description
1
I2C module 0 is reset.
0
I2C module 0 is not reset.
July 17, 2013
315
Texas Instruments-Production Data
System Control
Register 50: Controller Area Network Software Reset (SRCAN), offset 0x534
The SRCAN register provides software the capability to reset the available CAN modules. This
register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the CAN modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRCAN register. While the SRCAN bit is 1, the peripheral is
held in reset.
2. Software completes the reset process by clearing the SRCAN bit.
There may be latency from the clearing of the SRCAN bit to when the peripheral is ready for use.
Software can check the corresponding PRCAN bit to be sure.
Important: This register should be used to reset the CAN modules. To support legacy software,
the SRCR0 register is available. Setting a bit in the SRCR0 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR0 register can
be read back correctly when reading the SRCR0 register. If software uses this register
to reset a legacy peripheral (such as CAN0), the write causes proper operation, but the
value of that bit is not reflected in the SRCR0 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Controller Area Network Software Reset (SRCAN)
Base 0x400F.E000
Offset 0x534
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
R/W
0
CAN Module 1 Software Reset
Value Description
1
CAN module 1 is reset.
0
CAN module 1 is not reset.
316
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
0
R0
R/W
0
Description
CAN Module 0 Software Reset
Value Description
1
CAN module 0 is reset.
0
CAN module 0 is not reset.
July 17, 2013
317
Texas Instruments-Production Data
System Control
Register 51: Analog-to-Digital Converter Software Reset (SRADC), offset 0x538
The SRADC register provides software the capability to reset the available ADC modules. This
register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the ADC modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRADC register. While the SRADC bit is 1, the peripheral is
held in reset.
2. Software completes the reset process by clearing the SRADC bit.
There may be latency from the clearing of the SRADC bit to when the peripheral is ready for use.
Software can check the corresponding PRADC bit to be sure.
Important: This register should be used to reset the ADC modules. To support legacy software,
the SRCR0 register is available. Setting a bit in the SRCR0 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR0 register can
be read back correctly when reading the SRCR0 register. If software uses this register
to reset a legacy peripheral (such as ADC0), the write causes proper operation, but the
value of that bit is not reflected in the SRCR0 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Analog-to-Digital Converter Software Reset (SRADC)
Base 0x400F.E000
Offset 0x538
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
R/W
0
ADC Module 1 Software Reset
Value Description
1
ADC module 1 is reset.
0
ADC module 1 is not reset.
318
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
0
R0
R/W
0
Description
ADC Module 0 Software Reset
Value Description
1
ADC module 0 is reset.
0
ADC module 0 is not reset.
July 17, 2013
319
Texas Instruments-Production Data
System Control
Register 52: Analog Comparator Software Reset (SRACMP), offset 0x53C
The SRACMP register provides software the capability to reset the available analog comparator
module. This register provides the same capability as the legacy Software Reset Control n SRCRn
registers specifically for the analog comparator module and has the same bit polarity as the
corresponding SRCRn bits.
A block is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRACMP register. While the SRACMP bit is 1, the module
is held in reset.
2. Software completes the reset process by clearing the SRACMP bit.
There may be latency from the clearing of the SRACMP bit to when the module is ready for use.
Software can check the corresponding PRACMP bit to be sure.
Important: This register should be used to reset the analog comparator module. To support legacy
software, the SRCR1 register is available. Setting any of the COMPn bits in the SRCR0
register also resets the analog comparator module. If any of the COMPn bits are set by
writing to the SRCR1 register, it can be read back correctly when reading the SRCR0
register. If software uses this register to reset the analog comparator module, the write
causes proper operation, but the value of R0 is not reflected by the COMPn bits in the
SRCR1 register. If software uses both legacy and peripheral-specific register accesses,
the peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Analog Comparator Software Reset (SRACMP)
Base 0x400F.E000
Offset 0x53C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
R0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
R/W
0
Analog Comparator Module 0 Software Reset
Value Description
1
Analog comparator module is reset.
0
Analog comparator module is not reset.
320
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 53: Pulse Width Modulator Software Reset (SRPWM), offset 0x540
The SRPWM register provides software the capability to reset the available PWM modules. This
register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the PWM modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRPWM register. While the SRPWM bit is 1, the peripheral
is held in reset.
2. Software completes the reset process by clearing the SRPWM bit.
There may be latency from the clearing of the SRPWM bit to when the peripheral is ready for use.
Software can check the corresponding PRPWM bit to be sure.
Important: This register should be used to reset the PWM modules. To support legacy software,
the SRCR0 register is available. Setting the PWM bit in the SRCR0 register also resets
the PWM0 module. If the PWM bit is changed by writing to the SRCR0 register, it can
be read back correctly when reading the SRCR0 register. Software must use this register
to reset PWM1, which is not present in the legacy registers. If software uses this register
to reset PWM0, the write causes proper operation, but the value of that bit is not reflected
in the SRCR0 register. If software uses both legacy and peripheral-specific register
accesses, the peripheral-specific registers must be accessed by read-modify-write
operations that affect only peripherals that are not present in the legacy registers. In
this manner, both the peripheral-specific and legacy registers have coherent information.
Pulse Width Modulator Software Reset (SRPWM)
Base 0x400F.E000
Offset 0x540
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
R/W
0
PWM Module 1 Software Reset
Value Description
1
PWM module 1 is reset.
0
PWM module 1 is not reset.
July 17, 2013
321
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
0
R0
R/W
0
Description
PWM Module 0 Software Reset
Value Description
1
PWM module 0 is reset.
0
PWM module 0 is not reset.
322
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 54: Quadrature Encoder Interface Software Reset (SRQEI), offset
0x544
The SRQEI register provides software the capability to reset the available QEI modules. This register
provides the same capability as the legacy Software Reset Control n SRCRn registers specifically
for the QEI modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRQEI register. While the SRQEI bit is 1, the peripheral is
held in reset.
2. Software completes the reset process by clearing the SRQEI bit.
There may be latency from the clearing of the SRQEI bit to when the peripheral is ready for use.
Software can check the corresponding PRQEI bit to be sure.
Important: This register should be used to reset the QEI modules. To support legacy software, the
SRCR1 register is available. Setting a bit in the SRCR1 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR1 register can
be read back correctly when reading the SRCR1 register. If software uses this register
to reset a legacy peripheral (such as QEI0), the write causes proper operation, but the
value of that bit is not reflected in the SRCR1 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Quadrature Encoder Interface Software Reset (SRQEI)
Base 0x400F.E000
Offset 0x544
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
R1
R0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
R/W
0
QEI Module 1 Software Reset
Value Description
1
QEI module 1 is reset.
0
QEI module 1 is not reset.
July 17, 2013
323
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
0
R0
R/W
0
Description
QEI Module 0 Software Reset
Value Description
1
QEI module 0 is reset.
0
QEI module 0 is not reset.
324
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 55: EEPROM Software Reset (SREEPROM), offset 0x558
The SREEPROM register provides software the capability to reset the available EEPROM module.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SREEPROM register. While the SREEPROM bit is 1, the
peripheral is held in reset.
2. Software completes the reset process by clearing the SREEPROM bit.
There may be latency from the clearing of the SREEPROM bit to when the peripheral is ready for
use. Software can check the corresponding PREEPROM bit to be sure.
EEPROM Software Reset (SREEPROM)
Base 0x400F.E000
Offset 0x558
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
R0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
R/W
0
EEPROM Module Software Reset
Value Description
1
EEPROM module is reset.
0
EEPROM module is not reset.
July 17, 2013
325
Texas Instruments-Production Data
System Control
Register 56: 32/64-Bit Wide General-Purpose Timer Software Reset
(SRWTIMER), offset 0x55C
The SRWTIMER register provides software the capability to reset the available 32/64-bit wide timer
modules.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRWTIMER register. While the SRWTIMER bit is 1, the
peripheral is held in reset.
2. Software completes the reset process by clearing the SRWTIMER bit.
There may be latency from the clearing of the SRWTIMER bit to when the peripheral is ready for
use. Software can check the corresponding PRWTIMER bit to be sure.
32/64-Bit Wide General-Purpose Timer Software Reset (SRWTIMER)
Base 0x400F.E000
Offset 0x55C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
R/W
0
32/64-Bit Wide General-Purpose Timer 5 Software Reset
Value Description
4
R4
R/W
0
1
32/64-bit wide general-purpose timer module 5 is reset.
0
32/64-bit wide general-purpose timer module 5 is not reset.
32/64-Bit Wide General-Purpose Timer 4 Software Reset
Value Description
3
R3
R/W
0
1
32/64-bit wide general-purpose timer module 4 is reset.
0
32/64-bit wide general-purpose timer module 4 is not reset.
32/64-Bit Wide General-Purpose Timer 3 Software Reset
Value Description
1
32/64-bit wide general-purpose timer module 3 is reset.
0
32/64-bit wide general-purpose timer module 3 is not reset.
326
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
2
R2
R/W
0
Description
32/64-Bit Wide General-Purpose Timer 2 Software Reset
Value Description
1
R1
R/W
0
1
32/64-bit wide general-purpose timer module 2 is reset.
0
32/64-bit wide general-purpose timer module 2 is not reset.
32/64-Bit Wide General-Purpose Timer 1 Software Reset
Value Description
0
R0
R/W
0
1
32/64-bit wide general-purpose timer module 1 is reset.
0
32/64-bit wide general-purpose timer module 1 is not reset.
32/64-Bit Wide General-Purpose Timer 0 Software Reset
Value Description
1
32/64-bit wide general-purpose timer module 0 is reset.
0
32/64-bit wide general-purpose timer module 0 is not reset.
July 17, 2013
327
Texas Instruments-Production Data
System Control
Register 57: Watchdog Timer Run Mode Clock Gating Control (RCGCWD),
offset 0x600
The RCGCWD register provides software the capability to enable and disable watchdog modules
in Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the watchdog modules. To
support legacy software, the RCGC0 register is available. A write to the RCGC0 register
also writes the corresponding bit in this register. Any bits that are changed by writing
to the RCGC0 register can be read back correctly with a read of the RCGC0 register.
If software uses this register to write a legacy peripheral (such as Watchdog 0), the
write causes proper operation, but the value of that bit is not reflected in the RCGC0
register. If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Watchdog Timer Run Mode Clock Gating Control (RCGCWD)
Base 0x400F.E000
Offset 0x600
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
R1
R0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
R/W
0
Watchdog Timer 1 Run Mode Clock Gating Control
Value Description
0
R0
R/W
0
1
Enable and provide a clock to Watchdog module 1 in Run mode.
0
Watchdog module 1 is disabled.
Watchdog Timer 0 Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to Watchdog module 0 in Run mode.
0
Watchdog module 0 is disabled.
328
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 58: 16/32-Bit General-Purpose Timer Run Mode Clock Gating Control
(RCGCTIMER), offset 0x604
The RCGCTIMER register provides software the capability to enable and disable 16/32-bit timer
modules in Run mode. When enabled, a module is provided a clock and accesses to module registers
are allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the timer modules and has the same
bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the timer modules. To support
legacy software, the RCGC1 register is available. A write to the RCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
RCGC1 register can be read back correctly with a read of the RCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as Timer 0), the write
causes proper operation, but the value of that bit is not reflected in the RCGC1 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
16/32-Bit General-Purpose Timer Run Mode Clock Gating Control (RCGCTIMER)
Base 0x400F.E000
Offset 0x604
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
R/W
0
16/32-Bit General-Purpose Timer 5 Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 5 in Run mode.
0
16/32-bit general-purpose timer module 5 is disabled.
July 17, 2013
329
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
4
R4
R/W
0
Description
16/32-Bit General-Purpose Timer 4 Run Mode Clock Gating Control
Value Description
3
R3
R/W
0
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 4 in Run mode.
0
16/32-bit general-purpose timer module 4 is disabled.
16/32-Bit General-Purpose Timer 3 Run Mode Clock Gating Control
Value Description
2
R2
R/W
0
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 3 in Run mode.
0
16/32-bit general-purpose timer module 3 is disabled.
16/32-Bit General-Purpose Timer 2 Run Mode Clock Gating Control
Value Description
1
R1
R/W
0
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 2 in Run mode.
0
16/32-bit general-purpose timer module 2 is disabled.
16/32-Bit General-Purpose Timer 1 Run Mode Clock Gating Control
Value Description
0
R0
R/W
0
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 1 in Run mode.
0
16/32-bit general-purpose timer module 1 is disabled.
16/32-Bit General-Purpose Timer 0 Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 0 in Run mode.
0
16/32-bit general-purpose timer module 0 is disabled.
330
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 59: General-Purpose Input/Output Run Mode Clock Gating Control
(RCGCGPIO), offset 0x608
The RCGCGPIO register provides software the capability to enable and disable GPIO modules in
Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the GPIO modules. To support
legacy software, the RCGC2 register is available. A write to the RCGC2 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
RCGC2 register can be read back correctly with a read of the RCGC2 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as GPIO A), the write
causes proper operation, but the value of that bit is not reflected in the RCGC2 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
General-Purpose Input/Output Run Mode Clock Gating Control (RCGCGPIO)
Base 0x400F.E000
Offset 0x608
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
4
3
2
1
0
R9
R8
R7
R6
R5
R4
R3
R2
R1
R0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:10
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
9
R9
R/W
0
GPIO Port K Run Mode Clock Gating Control
Value Description
8
R8
R/W
0
1
Enable and provide a clock to GPIO Port K in Run mode.
0
GPIO Port K is disabled.
GPIO Port J Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to GPIO Port J in Run mode.
0
GPIO Port J is disabled.
July 17, 2013
331
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
7
R7
R/W
0
Description
GPIO Port H Run Mode Clock Gating Control
Value Description
6
R6
R/W
0
1
Enable and provide a clock to GPIO Port H in Run mode.
0
GPIO Port H is disabled.
GPIO Port G Run Mode Clock Gating Control
Value Description
5
R5
R/W
0
1
Enable and provide a clock to GPIO Port G in Run mode.
0
GPIO Port G is disabled.
GPIO Port F Run Mode Clock Gating Control
Value Description
4
R4
R/W
0
1
Enable and provide a clock to GPIO Port F in Run mode.
0
GPIO Port F is disabled.
GPIO Port E Run Mode Clock Gating Control
Value Description
3
R3
R/W
0
1
Enable and provide a clock to GPIO Port E in Run mode.
0
GPIO Port E is disabled.
GPIO Port D Run Mode Clock Gating Control
Value Description
2
R2
R/W
0
1
Enable and provide a clock to GPIO Port D in Run mode.
0
GPIO Port D is disabled.
GPIO Port C Run Mode Clock Gating Control
Value Description
1
R1
R/W
0
1
Enable and provide a clock to GPIO Port C in Run mode.
0
GPIO Port C is disabled.
GPIO Port B Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to GPIO Port B in Run mode.
0
GPIO Port B is disabled.
332
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
0
R0
R/W
0
Description
GPIO Port A Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to GPIO Port A in Run mode.
0
GPIO Port A is disabled.
July 17, 2013
333
Texas Instruments-Production Data
System Control
Register 60: Micro Direct Memory Access Run Mode Clock Gating Control
(RCGCDMA), offset 0x60C
The RCGCDMA register provides software the capability to enable and disable the μDMA module
in Run mode. When enabled, the module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the μDMA module. To support
legacy software, the RCGC2 register is available. A write to the UDMA bit in the RCGC2
register also writes the R0 bit in this register. If the UDMA bit is changed by writing to the
RCGC2 register, it can be read back correctly with a read of the RCGC2 register. If
software uses this register to control the clock for the μDMA module, the write causes
proper operation, but the UDMA bit in the RCGC2 register does not reflect the value of
the R0 bit. If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Micro Direct Memory Access Run Mode Clock Gating Control (RCGCDMA)
Base 0x400F.E000
Offset 0x60C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
R0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
R/W
0
μDMA Module Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to the μDMA module in Run mode.
0
μDMA module is disabled.
334
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 61: Hibernation Run Mode Clock Gating Control (RCGCHIB), offset
0x614
The RCGCHIB register provides software the capability to enable and disable the Hibernation
module in Run mode. When enabled, the module is provided a clock and accesses to module
registers are allowed. When disabled, the clock is disabled to save power and accesses to module
registers generate a bus fault. This register provides the same capability as the legacy Run Mode
Clock Gating Control Register n RCGCn registers specifically for the watchdog modules and has
the same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the Hibernation module. To
support legacy software, the RCGC0 register is available. A write to the HIB bit in the
RCGC0 register also writes the R0 bit in this register. If the HIB bit is changed by writing
to the RCGC0 register, it can be read back correctly with a read of the RCGC0 register.
If software uses this register to control the clock for the Hibernation module, the write
causes proper operation, but the HIB bit in the RCGC0 register does not reflect the
value of the R0 bit. If software uses both legacy and peripheral-specific register accesses,
the peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Hibernation Run Mode Clock Gating Control (RCGCHIB)
Base 0x400F.E000
Offset 0x614
Type R/W, reset 0x0000.0001
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
1
reserved
Type
Reset
reserved
Type
Reset
RO
0
R0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
R/W
1
Hibernation Module Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to the Hibernation module in Run
mode.
0
Hibernation module is disabled.
July 17, 2013
335
Texas Instruments-Production Data
System Control
Register 62: Universal Asynchronous Receiver/Transmitter Run Mode Clock
Gating Control (RCGCUART), offset 0x618
The RCGCUART register provides software the capability to enable and disable the UART modules
in Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the UART modules. To support
legacy software, the RCGC1 register is available. A write to the RCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
RCGC1 register can be read back correctly with a read of the RCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as UART0), the write
causes proper operation, but the value of that bit is not reflected in the RCGC1 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Universal Asynchronous Receiver/Transmitter Run Mode Clock Gating Control (RCGCUART)
Base 0x400F.E000
Offset 0x618
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
R7
R6
R5
R4
R3
R2
R1
R0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:8
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7
R7
R/W
0
UART Module 7 Run Mode Clock Gating Control
Value Description
6
R6
R/W
0
1
Enable and provide a clock to UART module 7 in Run mode.
0
UART module 7 is disabled.
UART Module 6 Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to UART module 6 in Run mode.
0
UART module 6 is disabled.
336
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
5
R5
R/W
0
Description
UART Module 5 Run Mode Clock Gating Control
Value Description
4
R4
R/W
0
1
Enable and provide a clock to UART module 5 in Run mode.
0
UART module 5 is disabled.
UART Module 4 Run Mode Clock Gating Control
Value Description
3
R3
R/W
0
1
Enable and provide a clock to UART module 4 in Run mode.
0
UART module 4 is disabled.
UART Module 3 Run Mode Clock Gating Control
Value Description
2
R2
R/W
0
1
Enable and provide a clock to UART module 3 in Run mode.
0
UART module 3 is disabled.
UART Module 2 Run Mode Clock Gating Control
Value Description
1
R1
R/W
0
1
Enable and provide a clock to UART module 2 in Run mode.
0
UART module 2 is disabled.
UART Module 1 Run Mode Clock Gating Control
Value Description
0
R0
R/W
0
1
Enable and provide a clock to UART module 1 in Run mode.
0
UART module 1 is disabled.
UART Module 0 Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to UART module 0 in Run mode.
0
UART module 0 is disabled.
July 17, 2013
337
Texas Instruments-Production Data
System Control
Register 63: Synchronous Serial Interface Run Mode Clock Gating Control
(RCGCSSI), offset 0x61C
The RCGCSSI register provides software the capability to enable and disable the SSI modules in
Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the SSI modules. To support
legacy software, the RCGC1 register is available. A write to the RCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
RCGC1 register can be read back correctly with a read of the RCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as SSI0), the write causes
proper operation, but the value of that bit is not reflected in the RCGC1 register. If
software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Synchronous Serial Interface Run Mode Clock Gating Control (RCGCSSI)
Base 0x400F.E000
Offset 0x61C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
3
2
1
0
R3
R2
R1
R0
R/W
0
R/W
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3
R3
R/W
0
SSI Module 3 Run Mode Clock Gating Control
Value Description
2
R2
R/W
0
1
Enable and provide a clock to SSI module 3 in Run mode.
0
SSI module 3 is disabled.
SSI Module 2 Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to SSI module 2 in Run mode.
0
SSI module 2 is disabled.
338
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
1
R1
R/W
0
Description
SSI Module 1 Run Mode Clock Gating Control
Value Description
0
R0
R/W
0
1
Enable and provide a clock to SSI module 1 in Run mode.
0
SSI module 1 is disabled.
SSI Module 0 Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to SSI module 0 in Run mode.
0
SSI module 0 is disabled.
July 17, 2013
339
Texas Instruments-Production Data
System Control
Register 64: Inter-Integrated Circuit Run Mode Clock Gating Control
(RCGCI2C), offset 0x620
The RCGCI2C register provides software the capability to enable and disable the I2C modules in
Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the I2C modules. To support
legacy software, the RCGC1 register is available. A write to the RCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
RCGC1 register can be read back correctly with a read of the RCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as I2C0), the write causes
proper operation, but the value of that bit is not reflected in the RCGC1 register. If
software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Inter-Integrated Circuit Run Mode Clock Gating Control (RCGCI2C)
Base 0x400F.E000
Offset 0x620
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
RO
0
RO
0
RO
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
R/W
0
I2C Module 5 Run Mode Clock Gating Control
Value Description
4
R4
R/W
0
1
Enable and provide a clock to I2C module 5 in Run mode.
0
I2C module 5 is disabled.
I2C Module 4 Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to I2C module 4 in Run mode.
0
I2C module 4 is disabled.
340
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
3
R3
R/W
0
Description
I2C Module 3 Run Mode Clock Gating Control
Value Description
2
R2
R/W
0
1
Enable and provide a clock to I2C module 3 in Run mode.
0
I2C module 3 is disabled.
I2C Module 2 Run Mode Clock Gating Control
Value Description
1
R1
R/W
0
1
Enable and provide a clock to I2C module 2 in Run mode.
0
I2C module 2 is disabled.
I2C Module 1 Run Mode Clock Gating Control
Value Description
0
R0
R/W
0
1
Enable and provide a clock to I2C module 1 in Run mode.
0
I2C module 1 is disabled.
I2C Module 0 Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to I2C module 0 in Run mode.
0
I2C module 0 is disabled.
July 17, 2013
341
Texas Instruments-Production Data
System Control
Register 65: Controller Area Network Run Mode Clock Gating Control
(RCGCCAN), offset 0x634
The RCGCCAN register provides software the capability to enable and disable the CAN modules
in Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the CAN modules. To support
legacy software, the RCGC0 register is available. A write to the RCGC0 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
RCGC0 register can be read back correctly with a read of the RCGC0 register. If software
uses this register to write a legacy peripheral (such as CAN0), the write causes proper
operation, but the value of that bit is not reflected in the RCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Controller Area Network Run Mode Clock Gating Control (RCGCCAN)
Base 0x400F.E000
Offset 0x634
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
R1
R0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
R/W
0
CAN Module 1 Run Mode Clock Gating Control
Value Description
0
R0
R/W
0
1
Enable and provide a clock to CAN module 1 in Run mode.
0
CAN module 1 is disabled.
CAN Module 0 Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to CAN module 0 in Run mode.
0
CAN module 0 is disabled.
342
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 66: Analog-to-Digital Converter Run Mode Clock Gating Control
(RCGCADC), offset 0x638
The RCGCADC register provides software the capability to enable and disable the ADC modules
in Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the ADC modules. To support
legacy software, the RCGC0 register is available. A write to the RCGC0 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
RCGC0 register can be read back correctly with a read of the RCGC0 register. If software
uses this register to write a legacy peripheral (such as ADC0), the write causes proper
operation, but the value of that bit is not reflected in the RCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Analog-to-Digital Converter Run Mode Clock Gating Control (RCGCADC)
Base 0x400F.E000
Offset 0x638
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
R1
R0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
R/W
0
ADC Module 1 Run Mode Clock Gating Control
Value Description
0
R0
R/W
0
1
Enable and provide a clock to ADC module 1 in Run mode.
0
ADC module 1 is disabled.
ADC Module 0 Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to ADC module 0 in Run mode.
0
ADC module 0 is disabled.
July 17, 2013
343
Texas Instruments-Production Data
System Control
Register 67: Analog Comparator Run Mode Clock Gating Control
(RCGCACMP), offset 0x63C
The RCGCACMP register provides software the capability to enable and disable the analog
comparator module in Run mode. When enabled, the module is provided a clock and accesses to
module registers are allowed. When disabled, the clock is disabled to save power and accesses to
module registers generate a bus fault. This register provides the same capability as the legacy Run
Mode Clock Gating Control Register n RCGCn registers specifically for the watchdog modules
and has the same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the analog comparator module.
To support legacy software, the RCGC1 register is available. Setting any of the COMPn
bits in the RCGC1 register also sets the R0 bit in this register. If any of the COMPn bits
are set by writing to the RCGC1 register, it can be read back correctly when reading
the RCGC1 register. If software uses this register to change the clocking for the analog
comparator module, the write causes proper operation, but the value R0 is not reflected
by the COMPn bits in the RCGC1 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Analog Comparator Run Mode Clock Gating Control (RCGCACMP)
Base 0x400F.E000
Offset 0x63C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
R0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
R/W
0
Analog Comparator Module 0 Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to the analog comparator module
in Run mode.
0
Analog comparator module is disabled.
344
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 68: Pulse Width Modulator Run Mode Clock Gating Control
(RCGCPWM), offset 0x640
The RCGCPWM register provides software the capability to enable and disable the PWM modules
in Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the PWM modules. To support
legacy software, the RCGC0 register is available. A write to the PWM bit in the RCGC0
register also writes the R0 bit in this register. If the PWM bit is changed by writing to the
RCGC0 register, it can be read back correctly with a read of the RCGC0 register.
Software must use this register to support modules that are not present in the legacy
registers. If software uses this register to write to R0, the write causes proper operation,
but the value of that bit is not reflected in the PWM bit in the RCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Pulse Width Modulator Run Mode Clock Gating Control (RCGCPWM)
Base 0x400F.E000
Offset 0x640
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
R/W
0
PWM Module 1 Run Mode Clock Gating Control
Value Description
0
R0
R/W
0
1
Enable and provide a clock to PWM module 1 in Run mode.
0
PWM module 1 is disabled.
PWM Module 0 Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to PWM module 0 in Run mode.
0
PWM module 0 is disabled.
July 17, 2013
345
Texas Instruments-Production Data
System Control
Register 69: Quadrature Encoder Interface Run Mode Clock Gating Control
(RCGCQEI), offset 0x644
The RCGCQEI register provides software the capability to enable and disable the QEI modules in
Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the QEI modules. To support
legacy software, the RCGC1 register is available. A write to the RCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
RCGC1 register can be read back correctly with a read of the RCGC1 register. If software
uses this register to write a legacy peripheral (such as QEI0), the write causes proper
operation, but the value of that bit is not reflected in the RCGC1 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Quadrature Encoder Interface Run Mode Clock Gating Control (RCGCQEI)
Base 0x400F.E000
Offset 0x644
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
R1
R0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
R/W
0
QEI Module 1 Run Mode Clock Gating Control
Value Description
0
R0
R/W
0
1
Enable and provide a clock to QEI module 1 in Run mode.
0
QEI module 1 is disabled.
QEI Module 0 Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to QEI module 0 in Run mode.
0
QEI module 0 is disabled.
346
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 70: EEPROM Run Mode Clock Gating Control (RCGCEEPROM), offset
0x658
The RCGCEEPROM register provides software the capability to enable and disable the EEPROM
module in Run mode. When enabled, the module is provided a clock and accesses to module
registers are allowed. When disabled, the clock is disabled to save power and accesses to module
registers generate a bus fault.
EEPROM Run Mode Clock Gating Control (RCGCEEPROM)
Base 0x400F.E000
Offset 0x658
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
0
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
R/W
0
EEPROM Module Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to the EEPROM module in Run
mode.
0
EEPROM module is disabled.
July 17, 2013
347
Texas Instruments-Production Data
System Control
Register 71: 32/64-Bit Wide General-Purpose Timer Run Mode Clock Gating
Control (RCGCWTIMER), offset 0x65C
The RCGCWTIMER register provides software the capability to enable and disable 3264-bit timer
modules in Run mode. When enabled, a module is provided a clock and accesses to module registers
are allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the timer modules and has the same
bit polarity as the corresponding RCGCn bits.
32/64-Bit Wide General-Purpose Timer Run Mode Clock Gating Control (RCGCWTIMER)
Base 0x400F.E000
Offset 0x65C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
R/W
0
32/64-Bit Wide General-Purpose Timer 5 Run Mode Clock Gating Control
Value Description
4
R4
R/W
0
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 5 in Run mode.
0
32/64-bit wide general-purpose timer module 5 is disabled.
32/64-Bit Wide General-Purpose Timer 4 Run Mode Clock Gating Control
Value Description
3
R3
R/W
0
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 4 in Run mode.
0
32/64-bit wide general-purpose timer module 4 is disabled.
32/64-Bit Wide General-Purpose Timer 3 Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 3 in Run mode.
0
32/64-bit wide general-purpose timer module 3 is disabled.
348
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
2
R2
R/W
0
Description
32/64-Bit Wide General-Purpose Timer 2 Run Mode Clock Gating Control
Value Description
1
R1
R/W
0
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 2 in Run mode.
0
32/64-bit wide general-purpose timer module 2 is disabled.
32/64-Bit Wide General-Purpose Timer 1 Run Mode Clock Gating Control
Value Description
0
R0
R/W
0
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 1 in Run mode.
0
32/64-bit wide general-purpose timer module 1 is disabled.
32/64-Bit Wide General-Purpose Timer 0 Run Mode Clock Gating Control
Value Description
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 0 in Run mode.
0
32/64-bit wide general-purpose timer module 0 is disabled.
July 17, 2013
349
Texas Instruments-Production Data
System Control
Register 72: Watchdog Timer Sleep Mode Clock Gating Control (SCGCWD),
offset 0x700
The SCGCWD register provides software the capability to enable and disable watchdog modules
in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the watchdog modules. To
support legacy software, the SCGC0 register is available. A write to the SCGC0 register
also writes the corresponding bit in this register. Any bits that are changed by writing
to the SCGC0 register can be read back correctly with a read of the SCGC0 register.
If software uses this register to write a legacy peripheral (such as Watchdog 0), the
write causes proper operation, but the value of that bit is not reflected in the SCGC0
register. If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Watchdog Timer Sleep Mode Clock Gating Control (SCGCWD)
Base 0x400F.E000
Offset 0x700
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
S1
S0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
S1
R/W
0
Watchdog Timer 1 Sleep Mode Clock Gating Control
Value Description
0
S0
R/W
0
1
Enable and provide a clock to Watchdog module 1 in sleep
mode.
0
Watchdog module 1 is disabled.
Watchdog Timer 0 Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to Watchdog module 0 in sleep
mode.
0
Watchdog module 0 is disabled.
350
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 73: 16/32-Bit General-Purpose Timer Sleep Mode Clock Gating Control
(SCGCTIMER), offset 0x704
The SCGCTIMER register provides software the capability to enable and disable 16/32-bit timer
modules in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power. This register provides the same capability as the legacy Sleep Mode Clock
Gating Control Register n SCGCn registers specifically for the timer modules and has the same
bit polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the timer modules. To support
legacy software, the SCGC1 register is available. A write to the SCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
SCGC1 register can be read back correctly with a read of the SCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as Timer 0), the write
causes proper operation, but the value of that bit is not reflected in the SCGC1 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
16/32-Bit General-Purpose Timer Sleep Mode Clock Gating Control (SCGCTIMER)
Base 0x400F.E000
Offset 0x704
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
S5
S4
S3
S2
S1
S0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
S5
R/W
0
16/32-Bit General-Purpose Timer 5 Sleep Mode Clock Gating Control
Value Description
4
S4
R/W
0
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 5 in sleep mode.
0
16/32-bit general-purpose timer module 5 is disabled.
16/32-Bit General-Purpose Timer 4 Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 4 in sleep mode.
0
16/32-bit general-purpose timer module 4 is disabled.
July 17, 2013
351
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
3
S3
R/W
0
Description
16/32-Bit General-Purpose Timer 3 Sleep Mode Clock Gating Control
Value Description
2
S2
R/W
0
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 3 in sleep mode.
0
16/32-bit general-purpose timer module 3 is disabled.
16/32-Bit General-Purpose Timer 2 Sleep Mode Clock Gating Control
Value Description
1
S1
R/W
0
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 2 in sleep mode.
0
16/32-bit general-purpose timer module 2 is disabled.
16/32-Bit General-Purpose Timer 1 Sleep Mode Clock Gating Control
Value Description
0
S0
R/W
0
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 1 in sleep mode.
0
16/32-bit general-purpose timer module 1 is disabled.
16/32-Bit General-Purpose Timer 0 Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 0 in sleep mode.
0
16/32-bit general-purpose timer module 0 is disabled.
352
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 74: General-Purpose Input/Output Sleep Mode Clock Gating Control
(SCGCGPIO), offset 0x708
The SCGCGPIO register provides software the capability to enable and disable GPIO modules in
sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled to
save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the GPIO modules. To support
legacy software, the SCGC2 register is available. A write to the SCGC2 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
SCGC2 register can be read back correctly with a read of the SCGC2 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as GPIO A), the write
causes proper operation, but the value of that bit is not reflected in the SCGC2 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
General-Purpose Input/Output Sleep Mode Clock Gating Control (SCGCGPIO)
Base 0x400F.E000
Offset 0x708
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
4
3
2
1
0
S9
S8
S7
S6
S5
S4
S3
S2
S1
S0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:10
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
9
S9
R/W
0
GPIO Port K Sleep Mode Clock Gating Control
Value Description
8
S8
R/W
0
1
Enable and provide a clock to GPIO Port K in sleep mode.
0
GPIO Port K is disabled.
GPIO Port J Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to GPIO Port J in sleep mode.
0
GPIO Port J is disabled.
July 17, 2013
353
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
7
S7
R/W
0
Description
GPIO Port H Sleep Mode Clock Gating Control
Value Description
6
S6
R/W
0
1
Enable and provide a clock to GPIO Port H in sleep mode.
0
GPIO Port H is disabled.
GPIO Port G Sleep Mode Clock Gating Control
Value Description
5
S5
R/W
0
1
Enable and provide a clock to GPIO Port G in sleep mode.
0
GPIO Port G is disabled.
GPIO Port F Sleep Mode Clock Gating Control
Value Description
4
S4
R/W
0
1
Enable and provide a clock to GPIO Port F in sleep mode.
0
GPIO Port F is disabled.
GPIO Port E Sleep Mode Clock Gating Control
Value Description
3
S3
R/W
0
1
Enable and provide a clock to GPIO Port E in sleep mode.
0
GPIO Port E is disabled.
GPIO Port D Sleep Mode Clock Gating Control
Value Description
2
S2
R/W
0
1
Enable and provide a clock to GPIO Port D in sleep mode.
0
GPIO Port D is disabled.
GPIO Port C Sleep Mode Clock Gating Control
Value Description
1
S1
R/W
0
1
Enable and provide a clock to GPIO Port C in sleep mode.
0
GPIO Port C is disabled.
GPIO Port B Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to GPIO Port B in sleep mode.
0
GPIO Port B is disabled.
354
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
0
S0
R/W
0
Description
GPIO Port A Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to GPIO Port A in sleep mode.
0
GPIO Port A is disabled.
July 17, 2013
355
Texas Instruments-Production Data
System Control
Register 75: Micro Direct Memory Access Sleep Mode Clock Gating Control
(SCGCDMA), offset 0x70C
The SCGCDMA register provides software the capability to enable and disable the μDMA module
in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the μDMA module. To support
legacy software, the SCGC2 register is available. A write to the UDMA bit in the SCGC2
register also writes the S0 bit in this register. If the UDMA bit is changed by writing to the
SCGC2 register, it can be read back correctly with a read of the SCGC2 register. If
software uses this register to control the clock for the μDMA module, the write causes
proper operation, but the UDMA bit in the SCGC2 register does not reflect the value of
the S0 bit. If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Micro Direct Memory Access Sleep Mode Clock Gating Control (SCGCDMA)
Base 0x400F.E000
Offset 0x70C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
S0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
S0
R/W
0
μDMA Module Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to the μDMA module in sleep mode.
0
μDMA module is disabled.
356
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 76: Hibernation Sleep Mode Clock Gating Control (SCGCHIB), offset
0x714
The SCGCHIB register provides software the capability to enable and disable the Hibernation module
in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the Hibernation module. To
support legacy software, the SCGC0 register is available. A write to the HIB bit in the
SCGC0 register also writes the S0 bit in this register. If the HIB bit is changed by writing
to the SCGC0 register, it can be read back correctly with a read of the SCGC0 register.
If software uses this register to control the clock for the Hibernation module, the write
causes proper operation, but the HIB bit in the SCGC0 register does not reflect the
value of the S0 bit. If software uses both legacy and peripheral-specific register accesses,
the peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Hibernation Sleep Mode Clock Gating Control (SCGCHIB)
Base 0x400F.E000
Offset 0x714
Type R/W, reset 0x0000.0001
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
1
reserved
Type
Reset
reserved
Type
Reset
RO
0
S0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
S0
R/W
1
Hibernation Module Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to the Hibernation module in sleep
mode.
0
Hibernation module is disabled.
July 17, 2013
357
Texas Instruments-Production Data
System Control
Register 77: Universal Asynchronous Receiver/Transmitter Sleep Mode Clock
Gating Control (SCGCUART), offset 0x718
The SCGCUART register provides software the capability to enable and disable the UART modules
in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the UART modules. To support
legacy software, the SCGC1 register is available. A write to the SCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
SCGC1 register can be read back correctly with a read of the SCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as UART0), the write
causes proper operation, but the value of that bit is not reflected in the SCGC1 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Universal Asynchronous Receiver/Transmitter Sleep Mode Clock Gating Control (SCGCUART)
Base 0x400F.E000
Offset 0x718
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
S7
S6
S5
S4
S3
S2
S1
S0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:8
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7
S7
R/W
0
UART Module 7 Sleep Mode Clock Gating Control
Value Description
6
S6
R/W
0
1
Enable and provide a clock to UART module 7 in sleep mode.
0
UART module 7 is disabled.
UART Module 6 Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to UART module 6 in sleep mode.
0
UART module 6 is disabled.
358
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
5
S5
R/W
0
Description
UART Module 5 Sleep Mode Clock Gating Control
Value Description
4
S4
R/W
0
1
Enable and provide a clock to UART module 5 in sleep mode.
0
UART module 5 is disabled.
UART Module 4 Sleep Mode Clock Gating Control
Value Description
3
S3
R/W
0
1
Enable and provide a clock to UART module 4 in sleep mode.
0
UART module 4 is disabled.
UART Module 3 Sleep Mode Clock Gating Control
Value Description
2
S2
R/W
0
1
Enable and provide a clock to UART module 3 in sleep mode.
0
UART module 3 is disabled.
UART Module 2 Sleep Mode Clock Gating Control
Value Description
1
S1
R/W
0
1
Enable and provide a clock to UART module 2 in sleep mode.
0
UART module 2 is disabled.
UART Module 1 Sleep Mode Clock Gating Control
Value Description
0
S0
R/W
0
1
Enable and provide a clock to UART module 1 in sleep mode.
0
UART module 1 is disabled.
UART Module 0 Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to UART module 0 in sleep mode.
0
UART module 0 is disabled.
July 17, 2013
359
Texas Instruments-Production Data
System Control
Register 78: Synchronous Serial Interface Sleep Mode Clock Gating Control
(SCGCSSI), offset 0x71C
The SCGCSSI register provides software the capability to enable and disable the SSI modules in
sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled to
save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the SSI modules. To support
legacy software, the SCGC1 register is available. A write to the SCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
SCGC1 register can be read back correctly with a read of the SCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as SSI0), the write causes
proper operation, but the value of that bit is not reflected in the SCGC1 register. If
software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Synchronous Serial Interface Sleep Mode Clock Gating Control (SCGCSSI)
Base 0x400F.E000
Offset 0x71C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
3
2
1
0
S3
S2
S1
S0
R/W
0
R/W
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3
S3
R/W
0
SSI Module 3 Sleep Mode Clock Gating Control
Value Description
2
S2
R/W
0
1
Enable and provide a clock to SSI module 3 in sleep mode.
0
SSI module 3 is disabled.
SSI Module 2 Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to SSI module 2 in sleep mode.
0
SSI module 2 is disabled.
360
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
1
S1
R/W
0
Description
SSI Module 1 Sleep Mode Clock Gating Control
Value Description
0
S0
R/W
0
1
Enable and provide a clock to SSI module 1 in sleep mode.
0
SSI module 1 is disabled.
SSI Module 0 Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to SSI module 0 in sleep mode.
0
SSI module 0 is disabled.
July 17, 2013
361
Texas Instruments-Production Data
System Control
Register 79: Inter-Integrated Circuit Sleep Mode Clock Gating Control
(SCGCI2C), offset 0x720
The SCGCI2C register provides software the capability to enable and disable the I2C modules in
sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled to
save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the I2C modules. To support
legacy software, the SCGC1 register is available. A write to the SCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
SCGC1 register can be read back correctly with a read of the SCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as I2C0), the write causes
proper operation, but the value of that bit is not reflected in the SCGC1 register. If
software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Inter-Integrated Circuit Sleep Mode Clock Gating Control (SCGCI2C)
Base 0x400F.E000
Offset 0x720
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
S5
S4
S3
S2
S1
S0
RO
0
RO
0
RO
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
S5
R/W
0
I2C Module 5 Sleep Mode Clock Gating Control
Value Description
4
S4
R/W
0
1
Enable and provide a clock to I2C module 5 in sleep mode.
0
I2C module 5 is disabled.
I2C Module 4 Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to I2C module 4 in sleep mode.
0
I2C module 4 is disabled.
362
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
3
S3
R/W
0
Description
I2C Module 3 Sleep Mode Clock Gating Control
Value Description
2
S2
R/W
0
1
Enable and provide a clock to I2C module 3 in sleep mode.
0
I2C module 3 is disabled.
I2C Module 2 Sleep Mode Clock Gating Control
Value Description
1
S1
R/W
0
1
Enable and provide a clock to I2C module 2 in sleep mode.
0
I2C module 2 is disabled.
I2C Module 1 Sleep Mode Clock Gating Control
Value Description
0
S0
R/W
0
1
Enable and provide a clock to I2C module 1 in sleep mode.
0
I2C module 1 is disabled.
I2C Module 0 Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to I2C module 0 in sleep mode.
0
I2C module 0 is disabled.
July 17, 2013
363
Texas Instruments-Production Data
System Control
Register 80: Controller Area Network Sleep Mode Clock Gating Control
(SCGCCAN), offset 0x734
The SCGCCAN register provides software the capability to enable and disable the CAN modules
in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the CAN modules. To support
legacy software, the SCGC0 register is available. A write to the SCGC0 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
SCGC0 register can be read back correctly with a read of the SCGC0 register. If software
uses this register to write a legacy peripheral (such as CAN0), the write causes proper
operation, but the value of that bit is not reflected in the SCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Controller Area Network Sleep Mode Clock Gating Control (SCGCCAN)
Base 0x400F.E000
Offset 0x734
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
S1
S0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
S1
R/W
0
CAN Module 1 Sleep Mode Clock Gating Control
Value Description
0
S0
R/W
0
1
Enable and provide a clock to CAN module 1 in sleep mode.
0
CAN module 1 is disabled.
CAN Module 0 Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to CAN module 0 in sleep mode.
0
CAN module 0 is disabled.
364
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 81: Analog-to-Digital Converter Sleep Mode Clock Gating Control
(SCGCADC), offset 0x738
The SCGCADC register provides software the capability to enable and disable the ADC modules
in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the ADC modules. To support
legacy software, the SCGC0 register is available. A write to the SCGC0 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
SCGC0 register can be read back correctly with a read of the SCGC0 register. If software
uses this register to write a legacy peripheral (such as ADC0), the write causes proper
operation, but the value of that bit is not reflected in the SCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Analog-to-Digital Converter Sleep Mode Clock Gating Control (SCGCADC)
Base 0x400F.E000
Offset 0x738
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
S1
S0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
S1
R/W
0
ADC Module 1 Sleep Mode Clock Gating Control
Value Description
0
S0
R/W
0
1
Enable and provide a clock to ADC module 1 in sleep mode.
0
ADC module 1 is disabled.
ADC Module 0 Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to ADC module 0 in sleep mode.
0
ADC module 0 is disabled.
July 17, 2013
365
Texas Instruments-Production Data
System Control
Register 82: Analog Comparator Sleep Mode Clock Gating Control
(SCGCACMP), offset 0x73C
The SCGCACMP register provides software the capability to enable and disable the analog
comparator module in sleep mode. When enabled, a module is provided a clock. When disabled,
the clock is disabled to save power. This register provides the same capability as the legacy Sleep
Mode Clock Gating Control Register n SCGCn registers specifically for the watchdog modules
and has the same bit polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the analog comparator module.
To support legacy software, the SCGC1 register is available. Setting any of the COMPn
bits in the SCGC1 register also sets the S0 bit in this register. If any of the COMPn bits
are set by writing to the SCGC1 register, it can be read back correctly when reading
the SCGC1 register. If software uses this register to change the clocking for the analog
comparator module, the write causes proper operation, but the value S0 is not reflected
by the COMPn bits in the SCGC1 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Analog Comparator Sleep Mode Clock Gating Control (SCGCACMP)
Base 0x400F.E000
Offset 0x73C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
S0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
S0
R/W
0
Analog Comparator Module 0 Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to the analog comparator module
in sleep mode.
0
Analog comparator module is disabled.
366
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 83: Pulse Width Modulator Sleep Mode Clock Gating Control
(SCGCPWM), offset 0x740
The SCGCPWM register provides software the capability to enable and disable the PWM modules
in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the PWM modules. To support
legacy software, the SCGC0 register is available. A write to the PWM bit in the SCGC0
register also writes the S0 bit in this register. If the PWM bit is changed by writing to the
SCGC0 register, it can be read back correctly with a read of the SCGC0 register.
Software must use this register to support modules that are not present in the legacy
registers. If software uses this register to write to S0, the write causes proper operation,
but the value of that bit is not reflected in the PWM bit in the SCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Pulse Width Modulator Sleep Mode Clock Gating Control (SCGCPWM)
Base 0x400F.E000
Offset 0x740
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
S1
S0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
S1
R/W
0
PWM Module 1 Sleep Mode Clock Gating Control
Value Description
0
S0
R/W
0
1
Enable and provide a clock to PWM module 1 in sleep mode.
0
PWM module 1 is disabled.
PWM Module 0 Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to PWM module 0 in sleep mode.
0
PWM module 0 is disabled.
July 17, 2013
367
Texas Instruments-Production Data
System Control
Register 84: Quadrature Encoder Interface Sleep Mode Clock Gating Control
(SCGCQEI), offset 0x744
The SCGCQEI register provides software the capability to enable and disable the QEI modules in
sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled to
save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the QEI modules. To support
legacy software, the SCGC1 register is available. A write to the SCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
SCGC1 register can be read back correctly with a read of the SCGC1 register. If software
uses this register to write a legacy peripheral (such as QEI0), the write causes proper
operation, but the value of that bit is not reflected in the SCGC1 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Quadrature Encoder Interface Sleep Mode Clock Gating Control (SCGCQEI)
Base 0x400F.E000
Offset 0x744
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
S1
S0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
S1
R/W
0
QEI Module 1 Sleep Mode Clock Gating Control
Value Description
0
S0
R/W
0
1
Enable and provide a clock to QEI module 1 in sleep mode.
0
QEI module 1 is disabled.
QEI Module 0 Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to QEI module 0 in sleep mode.
0
QEI module 0 is disabled.
368
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 85: EEPROM Sleep Mode Clock Gating Control (SCGCEEPROM),
offset 0x758
The SCGCEEPROM register provides software the capability to enable and disable the EEPROM
module in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power.
EEPROM Sleep Mode Clock Gating Control (SCGCEEPROM)
Base 0x400F.E000
Offset 0x758
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
0
S0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
S0
R/W
0
EEPROM Module Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to the EEPROM module in sleep
mode.
0
EEPROM module is disabled.
July 17, 2013
369
Texas Instruments-Production Data
System Control
Register 86: 32/64-Bit Wide General-Purpose Timer Sleep Mode Clock Gating
Control (SCGCWTIMER), offset 0x75C
The SCGCWTIMER register provides software the capability to enable and disable 3264-bit timer
modules in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power. This register provides the same capability as the legacy Sleep Mode Clock
Gating Control Register n SCGCn registers specifically for the timer modules and has the same
bit polarity as the corresponding SCGCn bits.
32/64-Bit Wide General-Purpose Timer Sleep Mode Clock Gating Control (SCGCWTIMER)
Base 0x400F.E000
Offset 0x75C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
S5
S4
S3
S2
S1
S0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
S5
R/W
0
32/64-Bit Wide General-Purpose Timer 5 Sleep Mode Clock Gating
Control
Value Description
4
S4
R/W
0
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 5 in sleep mode.
0
32/64-bit wide general-purpose timer module 5 is disabled.
32/64-Bit Wide General-Purpose Timer 4 Sleep Mode Clock Gating
Control
Value Description
3
S3
R/W
0
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 4 in sleep mode.
0
32/64-bit wide general-purpose timer module 4 is disabled.
32/64-Bit Wide General-Purpose Timer 3 Sleep Mode Clock Gating
Control
Value Description
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 3 in sleep mode.
0
32/64-bit wide general-purpose timer module 3 is disabled.
370
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
2
S2
R/W
0
Description
32/64-Bit Wide General-Purpose Timer 2 Sleep Mode Clock Gating
Control
Value Description
1
S1
R/W
0
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 2 in sleep mode.
0
32/64-bit wide general-purpose timer module 2 is disabled.
32/64-Bit Wide General-Purpose Timer 1 Sleep Mode Clock Gating
Control
Value Description
0
S0
R/W
0
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 1 in sleep mode.
0
32/64-bit wide general-purpose timer module 1 is disabled.
32/64-Bit Wide General-Purpose Timer 0 Sleep Mode Clock Gating
Control
Value Description
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 0 in sleep mode.
0
32/64-bit wide general-purpose timer module 0 is disabled.
July 17, 2013
371
Texas Instruments-Production Data
System Control
Register 87: Watchdog Timer Deep-Sleep Mode Clock Gating Control
(DCGCWD), offset 0x800
The DCGCWD register provides software the capability to enable and disable watchdog modules
in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power. This register provides the same capability as the legacy Deep-Sleep Mode
Clock Gating Control Register n DCGCn registers specifically for the watchdog modules and has
the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the watchdog modules. To
support legacy software, the DCGC0 register is available. A write to the DCGC0 register
also writes the corresponding bit in this register. Any bits that are changed by writing
to the DCGC0 register can be read back correctly with a read of the DCGC0 register.
If software uses this register to write a legacy peripheral (such as Watchdog 0), the
write causes proper operation, but the value of that bit is not reflected in the DCGC0
register. If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Watchdog Timer Deep-Sleep Mode Clock Gating Control (DCGCWD)
Base 0x400F.E000
Offset 0x800
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
D1
D0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
D1
R/W
0
Watchdog Timer 1 Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
R/W
0
1
Enable and provide a clock to Watchdog module 1 in deep-sleep
mode.
0
Watchdog module 1 is disabled.
Watchdog Timer 0 Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to Watchdog module 0 in deep-sleep
mode.
0
Watchdog module 0 is disabled.
372
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 88: 16/32-Bit General-Purpose Timer Deep-Sleep Mode Clock Gating
Control (DCGCTIMER), offset 0x804
The DCGCTIMER register provides software the capability to enable and disable 16/32-bit timer
modules in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the
clock is disabled to save power. This register provides the same capability as the legacy Deep-Sleep
Mode Clock Gating Control Register n DCGCn registers specifically for the timer modules and
has the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the timer modules. To support
legacy software, the DCGC1 register is available. A write to the DCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
DCGC1 register can be read back correctly with a read of the DCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as Timer 0), the write
causes proper operation, but the value of that bit is not reflected in the DCGC1 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
16/32-Bit General-Purpose Timer Deep-Sleep Mode Clock Gating Control (DCGCTIMER)
Base 0x400F.E000
Offset 0x804
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
D5
D4
D3
D2
D1
D0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
D5
R/W
0
16/32-Bit General-Purpose Timer 5 Deep-Sleep Mode Clock Gating
Control
Value Description
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 5 in deep-sleep mode.
0
16/32-bit general-purpose timer module 5 is disabled.
July 17, 2013
373
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
4
D4
R/W
0
Description
16/32-Bit General-Purpose Timer 4 Deep-Sleep Mode Clock Gating
Control
Value Description
3
D3
R/W
0
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 4 in deep-sleep mode.
0
16/32-bit general-purpose timer module 4 is disabled.
16/32-Bit General-Purpose Timer 3 Deep-Sleep Mode Clock Gating
Control
Value Description
2
D2
R/W
0
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 3 in deep-sleep mode.
0
16/32-bit general-purpose timer module 3 is disabled.
16/32-Bit General-Purpose Timer 2 Deep-Sleep Mode Clock Gating
Control
Value Description
1
D1
R/W
0
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 2 in deep-sleep mode.
0
16/32-bit general-purpose timer module 2 is disabled.
16/32-Bit General-Purpose Timer 1 Deep-Sleep Mode Clock Gating
Control
Value Description
0
D0
R/W
0
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 1 in deep-sleep mode.
0
16/32-bit general-purpose timer module 1 is disabled.
16/32-Bit General-Purpose Timer 0 Deep-Sleep Mode Clock Gating
Control
Value Description
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 0 in deep-sleep mode.
0
16/32-bit general-purpose timer module 0 is disabled.
374
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 89: General-Purpose Input/Output Deep-Sleep Mode Clock Gating
Control (DCGCGPIO), offset 0x808
The DCGCGPIO register provides software the capability to enable and disable GPIO modules in
deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Deep-Sleep Mode Clock
Gating Control Register n DCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the GPIO modules. To support
legacy software, the DCGC2 register is available. A write to the DCGC2 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
DCGC2 register can be read back correctly with a read of the DCGC2 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as GPIO A), the write
causes proper operation, but the value of that bit is not reflected in the DCGC2 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
General-Purpose Input/Output Deep-Sleep Mode Clock Gating Control (DCGCGPIO)
Base 0x400F.E000
Offset 0x808
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
4
3
2
1
0
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:10
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
9
D9
R/W
0
GPIO Port K Deep-Sleep Mode Clock Gating Control
Value Description
8
D8
R/W
0
1
Enable and provide a clock to GPIO Port K in deep-sleep mode.
0
GPIO Port K is disabled.
GPIO Port J Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to GPIO Port J in deep-sleep mode.
0
GPIO Port J is disabled.
July 17, 2013
375
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
7
D7
R/W
0
Description
GPIO Port H Deep-Sleep Mode Clock Gating Control
Value Description
6
D6
R/W
0
1
Enable and provide a clock to GPIO Port H in deep-sleep mode.
0
GPIO Port H is disabled.
GPIO Port G Deep-Sleep Mode Clock Gating Control
Value Description
5
D5
R/W
0
1
Enable and provide a clock to GPIO Port G in deep-sleep mode.
0
GPIO Port G is disabled.
GPIO Port F Deep-Sleep Mode Clock Gating Control
Value Description
4
D4
R/W
0
1
Enable and provide a clock to GPIO Port F in deep-sleep mode.
0
GPIO Port F is disabled.
GPIO Port E Deep-Sleep Mode Clock Gating Control
Value Description
3
D3
R/W
0
1
Enable and provide a clock to GPIO Port E in deep-sleep mode.
0
GPIO Port E is disabled.
GPIO Port D Deep-Sleep Mode Clock Gating Control
Value Description
2
D2
R/W
0
1
Enable and provide a clock to GPIO Port D in deep-sleep mode.
0
GPIO Port D is disabled.
GPIO Port C Deep-Sleep Mode Clock Gating Control
Value Description
1
D1
R/W
0
1
Enable and provide a clock to GPIO Port C in deep-sleep mode.
0
GPIO Port C is disabled.
GPIO Port B Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to GPIO Port B in deep-sleep mode.
0
GPIO Port B is disabled.
376
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
0
D0
R/W
0
Description
GPIO Port A Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to GPIO Port A in deep-sleep mode.
0
GPIO Port A is disabled.
July 17, 2013
377
Texas Instruments-Production Data
System Control
Register 90: Micro Direct Memory Access Deep-Sleep Mode Clock Gating
Control (DCGCDMA), offset 0x80C
The DCGCDMA register provides software the capability to enable and disable the μDMA module
in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power. This register provides the same capability as the legacy Deep-Sleep Mode
Clock Gating Control Register n DCGCn registers specifically for the watchdog modules and has
the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the μDMA module. To support
legacy software, the DCGC2 register is available. A write to the UDMA bit in the DCGC2
register also writes the D0 bit in this register. If the UDMA bit is changed by writing to the
DCGC2 register, it can be read back correctly with a read of the DCGC2 register. If
software uses this register to control the clock for the μDMA module, the write causes
proper operation, but the UDMA bit in the DCGC2 register does not reflect the value of
the D0 bit. If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Micro Direct Memory Access Deep-Sleep Mode Clock Gating Control (DCGCDMA)
Base 0x400F.E000
Offset 0x80C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
D0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
D0
R/W
0
μDMA Module Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to the μDMA module in deep-sleep
mode.
0
μDMA module is disabled.
378
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 91: Hibernation Deep-Sleep Mode Clock Gating Control (DCGCHIB),
offset 0x814
The DCGCHIB register provides software the capability to enable and disable the Hibernation
module in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock
is disabled to save power. This register provides the same capability as the legacy Deep-Sleep
Mode Clock Gating Control Register n DCGCn registers specifically for the watchdog modules
and has the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the Hibernation module. To
support legacy software, the DCGC0 register is available. A write to the HIB bit in the
DCGC0 register also writes the D0 bit in this register. If the HIB bit is changed by writing
to the DCGC0 register, it can be read back correctly with a read of the DCGC0 register.
If software uses this register to control the clock for the Hibernation module, the write
causes proper operation, but the HIB bit in the DCGC0 register does not reflect the
value of the D0 bit. If software uses both legacy and peripheral-specific register accesses,
the peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Hibernation Deep-Sleep Mode Clock Gating Control (DCGCHIB)
Base 0x400F.E000
Offset 0x814
Type R/W, reset 0x0000.0001
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
1
reserved
Type
Reset
reserved
Type
Reset
RO
0
D0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
D0
R/W
1
Hibernation Module Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to the Hibernation module in
deep-sleep mode.
0
Hibernation module is disabled.
July 17, 2013
379
Texas Instruments-Production Data
System Control
Register 92: Universal Asynchronous Receiver/Transmitter Deep-Sleep Mode
Clock Gating Control (DCGCUART), offset 0x818
The DCGCUART register provides software the capability to enable and disable the UART modules
in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power. This register provides the same capability as the legacy Deep-Sleep Mode
Clock Gating Control Register n DCGCn registers specifically for the watchdog modules and has
the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the UART modules. To support
legacy software, the DCGC1 register is available. A write to the DCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
DCGC1 register can be read back correctly with a read of the DCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as UART0), the write
causes proper operation, but the value of that bit is not reflected in the DCGC1 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Universal Asynchronous Receiver/Transmitter Deep-Sleep Mode Clock Gating Control (DCGCUART)
Base 0x400F.E000
Offset 0x818
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
D7
D6
D5
D4
D3
D2
D1
D0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:8
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7
D7
R/W
0
UART Module 7 Deep-Sleep Mode Clock Gating Control
Value Description
6
D6
R/W
0
1
Enable and provide a clock to UART module 7 in deep-sleep
mode.
0
UART module 7 is disabled.
UART Module 6 Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to UART module 6 in deep-sleep
mode.
0
UART module 6 is disabled.
380
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
5
D5
R/W
0
Description
UART Module 5 Deep-Sleep Mode Clock Gating Control
Value Description
4
D4
R/W
0
1
Enable and provide a clock to UART module 5 in deep-sleep
mode.
0
UART module 5 is disabled.
UART Module 4 Deep-Sleep Mode Clock Gating Control
Value Description
3
D3
R/W
0
1
Enable and provide a clock to UART module 4 in deep-sleep
mode.
0
UART module 4 is disabled.
UART Module 3 Deep-Sleep Mode Clock Gating Control
Value Description
2
D2
R/W
0
1
Enable and provide a clock to UART module 3 in deep-sleep
mode.
0
UART module 3 is disabled.
UART Module 2 Deep-Sleep Mode Clock Gating Control
Value Description
1
D1
R/W
0
1
Enable and provide a clock to UART module 2 in deep-sleep
mode.
0
UART module 2 is disabled.
UART Module 1 Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
R/W
0
1
Enable and provide a clock to UART module 1 in deep-sleep
mode.
0
UART module 1 is disabled.
UART Module 0 Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to UART module 0 in deep-sleep
mode.
0
UART module 0 is disabled.
July 17, 2013
381
Texas Instruments-Production Data
System Control
Register 93: Synchronous Serial Interface Deep-Sleep Mode Clock Gating
Control (DCGCSSI), offset 0x81C
The DCGCSSI register provides software the capability to enable and disable the SSI modules in
deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Deep-Sleep Mode Clock
Gating Control Register n DCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the SSI modules. To support
legacy software, the DCGC1 register is available. A write to the DCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
DCGC1 register can be read back correctly with a read of the DCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as SSI0), the write causes
proper operation, but the value of that bit is not reflected in the DCGC1 register. If
software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Synchronous Serial Interface Deep-Sleep Mode Clock Gating Control (DCGCSSI)
Base 0x400F.E000
Offset 0x81C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
3
2
1
0
D3
D2
D1
D0
R/W
0
R/W
0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3
D3
R/W
0
SSI Module 3 Deep-Sleep Mode Clock Gating Control
Value Description
2
D2
R/W
0
1
Enable and provide a clock to SSI module 3 in deep-sleep mode.
0
SSI module 3 is disabled.
SSI Module 2 Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to SSI module 2 in deep-sleep mode.
0
SSI module 2 is disabled.
382
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
1
D1
R/W
0
Description
SSI Module 1 Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
R/W
0
1
Enable and provide a clock to SSI module 1 in deep-sleep mode.
0
SSI module 1 is disabled.
SSI Module 0 Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to SSI module 0 in deep-sleep mode.
0
SSI module 0 is disabled.
July 17, 2013
383
Texas Instruments-Production Data
System Control
Register 94: Inter-Integrated Circuit Deep-Sleep Mode Clock Gating Control
(DCGCI2C), offset 0x820
The DCGCI2C register provides software the capability to enable and disable the I2C modules in
deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Deep-Sleep Mode Clock
Gating Control Register n DCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the I2C modules. To support
legacy software, the DCGC1 register is available. A write to the DCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
DCGC1 register can be read back correctly with a read of the DCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as I2C0), the write causes
proper operation, but the value of that bit is not reflected in the DCGC1 register. If
software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Inter-Integrated Circuit Deep-Sleep Mode Clock Gating Control (DCGCI2C)
Base 0x400F.E000
Offset 0x820
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
D5
D4
D3
D2
D1
D0
RO
0
RO
0
RO
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
D5
R/W
0
I2C Module 5 Deep-Sleep Mode Clock Gating Control
Value Description
4
D4
R/W
0
1
Enable and provide a clock to I2C module 5 in deep-sleep mode.
0
I2C module 5 is disabled.
I2C Module 4 Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to I2C module 4 in deep-sleep mode.
0
I2C module 4 is disabled.
384
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
3
D3
R/W
0
Description
I2C Module 3 Deep-Sleep Mode Clock Gating Control
Value Description
2
D2
R/W
0
1
Enable and provide a clock to I2C module 3 in deep-sleep mode.
0
I2C module 3 is disabled.
I2C Module 2 Deep-Sleep Mode Clock Gating Control
Value Description
1
D1
R/W
0
1
Enable and provide a clock to I2C module 2 in deep-sleep mode.
0
I2C module 2 is disabled.
I2C Module 1 Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
R/W
0
1
Enable and provide a clock to I2C module 1 in deep-sleep mode.
0
I2C module 1 is disabled.
I2C Module 0 Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to I2C module 0 in deep-sleep mode.
0
I2C module 0 is disabled.
July 17, 2013
385
Texas Instruments-Production Data
System Control
Register 95: Controller Area Network Deep-Sleep Mode Clock Gating Control
(DCGCCAN), offset 0x834
The DCGCCAN register provides software the capability to enable and disable the CAN modules
in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power. This register provides the same capability as the legacy Deep-Sleep Mode
Clock Gating Control Register n DCGCn registers specifically for the watchdog modules and has
the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the CAN modules. To support
legacy software, the DCGC0 register is available. A write to the DCGC0 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
DCGC0 register can be read back correctly with a read of the DCGC0 register. If software
uses this register to write a legacy peripheral (such as CAN0), the write causes proper
operation, but the value of that bit is not reflected in the DCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Controller Area Network Deep-Sleep Mode Clock Gating Control (DCGCCAN)
Base 0x400F.E000
Offset 0x834
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
D1
D0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
D1
R/W
0
CAN Module 1 Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
R/W
0
1
Enable and provide a clock to CAN module 1 in deep-sleep
mode.
0
CAN module 1 is disabled.
CAN Module 0 Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to CAN module 0 in deep-sleep
mode.
0
CAN module 0 is disabled.
386
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 96: Analog-to-Digital Converter Deep-Sleep Mode Clock Gating
Control (DCGCADC), offset 0x838
The DCGCADC register provides software the capability to enable and disable the ADC modules
in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power. This register provides the same capability as the legacy Deep-Sleep Mode
Clock Gating Control Register n DCGCn registers specifically for the watchdog modules and has
the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the ADC modules. To support
legacy software, the DCGC0 register is available. A write to the DCGC0 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
DCGC0 register can be read back correctly with a read of the DCGC0 register. If software
uses this register to write a legacy peripheral (such as ADC0), the write causes proper
operation, but the value of that bit is not reflected in the DCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Analog-to-Digital Converter Deep-Sleep Mode Clock Gating Control (DCGCADC)
Base 0x400F.E000
Offset 0x838
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
D1
D0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
D1
R/W
0
ADC Module 1 Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
R/W
0
1
Enable and provide a clock to ADC module 1 in deep-sleep
mode.
0
ADC module 1 is disabled.
ADC Module 0 Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to ADC module 0 in deep-sleep
mode.
0
ADC module 0 is disabled.
July 17, 2013
387
Texas Instruments-Production Data
System Control
Register 97: Analog Comparator Deep-Sleep Mode Clock Gating Control
(DCGCACMP), offset 0x83C
The DCGCACMP register provides software the capability to enable and disable the analog
comparator module in deep-sleep mode. When enabled, a module is provided a clock. When
disabled, the clock is disabled to save power. This register provides the same capability as the
legacy Deep-Sleep Mode Clock Gating Control Register n DCGCn registers specifically for the
watchdog modules and has the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the analog comparator module.
To support legacy software, the DCGC1 register is available. Setting any of the COMPn
bits in the DCGC1 register also sets the D0 bit in this register. If any of the COMPn bits
are set by writing to the DCGC1 register, it can be read back correctly when reading
the DCGC1 register. If software uses this register to change the clocking for the analog
comparator module, the write causes proper operation, but the value D0 is not reflected
by the COMPn bits in the DCGC1 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Analog Comparator Deep-Sleep Mode Clock Gating Control (DCGCACMP)
Base 0x400F.E000
Offset 0x83C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
D0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
D0
R/W
0
Analog Comparator Module 0 Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to the analog comparator module
in deep-sleep mode.
0
Analog comparator module is disabled.
388
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 98: Pulse Width Modulator Deep-Sleep Mode Clock Gating Control
(DCGCPWM), offset 0x840
The DCGCPWM register provides software the capability to enable and disable the PWM modules
in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power. This register provides the same capability as the legacy Deep-Sleep Mode
Clock Gating Control Register n DCGCn registers specifically for the watchdog modules and has
the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the PWM modules. To support
legacy software, the DCGC0 register is available. A write to the PWM bit in the DCGC0
register also writes the D0 bit in this register. If the PWM bit is changed by writing to the
DCGC0 register, it can be read back correctly with a read of the DCGC0 register.
Software must use this register to support modules that are not present in the legacy
registers. If software uses this register to write to D0, the write causes proper operation,
but the value of that bit is not reflected in the PWM bit in the DCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Pulse Width Modulator Deep-Sleep Mode Clock Gating Control (DCGCPWM)
Base 0x400F.E000
Offset 0x840
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
D1
D0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
R/W
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
D1
R/W
0
PWM Module 1 Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
R/W
0
1
Enable and provide a clock to PWM module 1 in deep-sleep
mode.
0
PWM module 1 is disabled.
PWM Module 0 Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to PWM module 0 in deep-sleep
mode.
0
PWM module 0 is disabled.
July 17, 2013
389
Texas Instruments-Production Data
System Control
Register 99: Quadrature Encoder Interface Deep-Sleep Mode Clock Gating
Control (DCGCQEI), offset 0x844
The DCGCQEI register provides software the capability to enable and disable the QEI modules in
deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Deep-Sleep Mode Clock
Gating Control Register n DCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the QEI modules. To support
legacy software, the DCGC1 register is available. A write to the DCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
DCGC1 register can be read back correctly with a read of the DCGC1 register. If software
uses this register to write a legacy peripheral (such as QEI0), the write causes proper
operation, but the value of that bit is not reflected in the DCGC1 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Quadrature Encoder Interface Deep-Sleep Mode Clock Gating Control (DCGCQEI)
Base 0x400F.E000
Offset 0x844
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
D1
D0
R/W
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
D1
R/W
0
QEI Module 1 Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
R/W
0
1
Enable and provide a clock to QEI module 1 in deep-sleep
mode.
0
QEI module 1 is disabled.
QEI Module 0 Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to QEI module 0 in deep-sleep
mode.
0
QEI module 0 is disabled.
390
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 100: EEPROM Deep-Sleep Mode Clock Gating Control
(DCGCEEPROM), offset 0x858
The DCGCEEPROM register provides software the capability to enable and disable the EEPROM
module in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock
is disabled to save power.
EEPROM Deep-Sleep Mode Clock Gating Control (DCGCEEPROM)
Base 0x400F.E000
Offset 0x858
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
0
D0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
R/W
0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
D0
R/W
0
EEPROM Module Deep-Sleep Mode Clock Gating Control
Value Description
1
Enable and provide a clock to the EEPROM module in
deep-sleep mode.
0
EEPROM module is disabled.
July 17, 2013
391
Texas Instruments-Production Data
System Control
Register 101: 32/64-Bit Wide General-Purpose Timer Deep-Sleep Mode Clock
Gating Control (DCGCWTIMER), offset 0x85C
The DCGCWTIMER register provides software the capability to enable and disable 32/64-bit wide
timer modules in deep-sleep mode. When enabled, a module is provided a clock. When disabled,
the clock is disabled to save power. This register provides the same capability as the legacy
Deep-Sleep Mode Clock Gating Control Register n DCGCn registers specifically for the timer
modules and has the same bit polarity as the corresponding DCGCn bits.
32/64-Bit Wide General-Purpose Timer Deep-Sleep Mode Clock Gating Control (DCGCWTIMER)
Base 0x400F.E000
Offset 0x85C
Type R/W, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
D5
D4
D3
D2
D1
D0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
D5
R/W
0
32/64-Bit Wide General-Purpose Timer 5 Deep-Sleep Mode Clock Gating
Control
Value Description
4
D4
R/W
0
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 5 in deep-sleep mode.
0
32/64-bit wide general-purpose timer module 5 is disabled.
32/64-Bit Wide General-Purpose Timer 4 Deep-Sleep Mode Clock Gating
Control
Value Description
3
D3
R/W
0
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 4 in deep-sleep mode.
0
32/64-bit wide general-purpose timer module 4 is disabled.
32/64-Bit Wide General-Purpose Timer 3 Deep-Sleep Mode Clock Gating
Control
Value Description
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 3 in deep-sleep mode.
0
32/64-bit wide general-purpose timer module 3 is disabled.
392
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
2
D2
R/W
0
Description
32/64-Bit Wide General-Purpose Timer 2 Deep-Sleep Mode Clock Gating
Control
Value Description
1
D1
R/W
0
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 2 in deep-sleep mode.
0
32/64-bit wide general-purpose timer module 2 is disabled.
32/64-Bit Wide General-Purpose Timer 1 Deep-Sleep Mode Clock Gating
Control
Value Description
0
D0
R/W
0
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 1 in deep-sleep mode.
0
32/64-bit wide general-purpose timer module 1 is disabled.
32/64-Bit Wide General-Purpose Timer 0 Deep-Sleep Mode Clock Gating
Control
Value Description
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 0 in deep-sleep mode.
0
32/64-bit wide general-purpose timer module 0 is disabled.
July 17, 2013
393
Texas Instruments-Production Data
System Control
Register 102: Watchdog Timer Peripheral Ready (PRWD), offset 0xA00
The PRWD register indicates whether the watchdog modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCWD bit is changed. A reset change is initiated if the
corresponding SRWD bit is changed from 0 to 1.
The PRWD bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Watchdog Timer Peripheral Ready (PRWD)
Base 0x400F.E000
Offset 0xA00
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
R1
R0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RO
0
Watchdog Timer 1 Peripheral Ready
Value Description
0
R0
RO
0
1
Watchdog module 1 is ready for access.
0
Watchdog module 1 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
Watchdog Timer 0 Peripheral Ready
Value Description
1
Watchdog module 0 is ready for access.
0
Watchdog module 0 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
394
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 103: 16/32-Bit General-Purpose Timer Peripheral Ready (PRTIMER),
offset 0xA04
The PRTIMER register indicates whether the timer modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCTIMER bit is changed. A reset change is initiated if the
corresponding SRTIMER bit is changed from 0 to 1.
The PRTIMER bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
16/32-Bit General-Purpose Timer Peripheral Ready (PRTIMER)
Base 0x400F.E000
Offset 0xA04
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
RO
0
16/32-Bit General-Purpose Timer 5 Peripheral Ready
Value Description
4
R4
RO
0
1
16/32-bit timer module 5 is ready for access.
0
16/32-bit timer module 5 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
16/32-Bit General-Purpose Timer 4 Peripheral Ready
Value Description
3
R3
RO
0
1
16/32-bit timer module 4 is ready for access.
0
16/32-bit timer module 4 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
16/32-Bit General-Purpose Timer 3 Peripheral Ready
Value Description
1
16/32-bit timer module 3 is ready for access.
0
16/32-bit timer module 3 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
July 17, 2013
395
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
2
R2
RO
0
Description
16/32-Bit General-Purpose Timer 2 Peripheral Ready
Value Description
1
R1
RO
0
1
16/32-bit timer module 2 is ready for access.
0
16/32-bit timer module 2 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
16/32-Bit General-Purpose Timer 1 Peripheral Ready
Value Description
0
R0
RO
0
1
16/32-bit timer module 1 is ready for access.
0
16/32-bit timer module 1 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
16/32-Bit General-Purpose Timer 0 Peripheral Ready
Value Description
1
16/32-bit timer module 0 is ready for access.
0
16/32-bit timer module 0 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
396
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 104: General-Purpose Input/Output Peripheral Ready (PRGPIO),
offset 0xA08
The PRGPIO register indicates whether the GPIO modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCGPIO bit is changed. A reset change is initiated if the
corresponding SRGPIO bit is changed from 0 to 1.
The PRGPIO bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
General-Purpose Input/Output Peripheral Ready (PRGPIO)
Base 0x400F.E000
Offset 0xA08
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R9
R8
R7
R6
R5
R4
R3
R2
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
Description
31:10
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
9
R9
RO
0
GPIO Port K Peripheral Ready
Value Description
8
R8
RO
0
1
GPIO Port K is ready for access.
0
GPIO Port K is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
GPIO Port J Peripheral Ready
Value Description
7
R7
RO
0
1
GPIO Port J is ready for access.
0
GPIO Port J is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
GPIO Port H Peripheral Ready
Value Description
1
GPIO Port H is ready for access.
0
GPIO Port H is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
July 17, 2013
397
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
6
R6
RO
0
Description
GPIO Port G Peripheral Ready
Value Description
5
R5
RO
0
1
GPIO Port G is ready for access.
0
GPIO Port G is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
GPIO Port F Peripheral Ready
Value Description
4
R4
RO
0
1
GPIO Port F is ready for access.
0
GPIO Port F is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
GPIO Port E Peripheral Ready
Value Description
3
R3
RO
0
1
GPIO Port E is ready for access.
0
GPIO Port E is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
GPIO Port D Peripheral Ready
Value Description
2
R2
RO
0
1
GPIO Port D is ready for access.
0
GPIO Port D is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
GPIO Port C Peripheral Ready
Value Description
1
R1
RO
0
1
GPIO Port C is ready for access.
0
GPIO Port C is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
GPIO Port B Peripheral Ready
Value Description
0
R0
RO
0
1
GPIO Port B is ready for access.
0
GPIO Port B is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
GPIO Port A Peripheral Ready
Value Description
1
GPIO Port A is ready for access.
0
GPIO Port A is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
398
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 105: Micro Direct Memory Access Peripheral Ready (PRDMA), offset
0xA0C
The PRDMA register indicates whether the μDMA module is ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCDMA bit is changed. A reset change is initiated if the
corresponding SRDMA bit is changed from 0 to 1.
The PRDMA bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Micro Direct Memory Access Peripheral Ready (PRDMA)
Base 0x400F.E000
Offset 0xA0C
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
R0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
RO
0
μDMA Module Peripheral Ready
Value Description
1
The μDMA module is ready for access.
0
The μDMA module is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
July 17, 2013
399
Texas Instruments-Production Data
System Control
Register 106: Hibernation Peripheral Ready (PRHIB), offset 0xA14
The PRHIB register indicates whether the Hibernation module is ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCHIB bit is changed. A reset change is initiated if the
corresponding SRHIB bit is changed from 0 to 1.
The PRHIB bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Hibernation Peripheral Ready (PRHIB)
Base 0x400F.E000
Offset 0xA14
Type RO, reset 0x0000.0001
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
0
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
RO
1
Hibernation Module Peripheral Ready
Value Description
1
The Hibernation module is ready for access.
0
The Hibernation module is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
400
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 107: Universal Asynchronous Receiver/Transmitter Peripheral Ready
(PRUART), offset 0xA18
The PRUART register indicates whether the UART modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCUART bit is changed. A reset change is initiated if the
corresponding SRUART bit is changed from 0 to 1.
The PRUART bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Universal Asynchronous Receiver/Transmitter Peripheral Ready (PRUART)
Base 0x400F.E000
Offset 0xA18
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R7
R6
R5
R4
R3
R2
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
Description
31:8
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7
R7
RO
0
UART Module 7 Peripheral Ready
Value Description
6
R6
RO
0
1
UART module 7 is ready for access.
0
UART module 7 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
UART Module 6 Peripheral Ready
Value Description
5
R5
RO
0
1
UART module 6 is ready for access.
0
UART module 6 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
UART Module 5 Peripheral Ready
Value Description
1
UART module 5 is ready for access.
0
UART module 5 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
July 17, 2013
401
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
4
R4
RO
0
Description
UART Module 4 Peripheral Ready
Value Description
3
R3
RO
0
1
UART module 4 is ready for access.
0
UART module 4 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
UART Module 3 Peripheral Ready
Value Description
2
R2
RO
0
1
UART module 3 is ready for access.
0
UART module 3 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
UART Module 2 Peripheral Ready
Value Description
1
R1
RO
0
1
UART module 2 is ready for access.
0
UART module 2 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
UART Module 1 Peripheral Ready
Value Description
0
R0
RO
0
1
UART module 1 is ready for access.
0
UART module 1 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
UART Module 0 Peripheral Ready
Value Description
1
UART module 0 is ready for access.
0
UART module 0 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
402
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 108: Synchronous Serial Interface Peripheral Ready (PRSSI), offset
0xA1C
The PRSSI register indicates whether the SSI modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCSSI bit is changed. A reset change is initiated if the
corresponding SRSSI bit is changed from 0 to 1.
The PRSSI bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Synchronous Serial Interface Peripheral Ready (PRSSI)
Base 0x400F.E000
Offset 0xA1C
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R3
R2
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3
R3
RO
0
SSI Module 3 Peripheral Ready
Value Description
2
R2
RO
0
1
SSI module 3 is ready for access.
0
SSI module 3 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
SSI Module 2 Peripheral Ready
Value Description
1
R1
RO
0
1
SSI module 2 is ready for access.
0
SSI module 2 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
SSI Module 1 Peripheral Ready
Value Description
1
SSI module 1 is ready for access.
0
SSI module 1 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
July 17, 2013
403
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
0
R0
RO
0
Description
SSI Module 0 Peripheral Ready
Value Description
1
SSI module 0 is ready for access.
0
SSI module 0 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
404
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 109: Inter-Integrated Circuit Peripheral Ready (PRI2C), offset 0xA20
The PRI2C register indicates whether the I2C modules are ready to be accessed by software following
a change in status of power, Run mode clocking, or reset. A Run mode clocking change is initiated
if the corresponding RCGCI2C bit is changed. A reset change is initiated if the corresponding SRI2C
bit is changed from 0 to 1.
The PRI2C bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Inter-Integrated Circuit Peripheral Ready (PRI2C)
Base 0x400F.E000
Offset 0xA20
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
RO
0
I2C Module 5 Peripheral Ready
Value Description
4
R4
RO
0
1
I2C module 5 is ready for access.
0
I2C module 5 is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
I2C Module 4 Peripheral Ready
Value Description
3
R3
RO
0
1
I2C module 4 is ready for access.
0
I2C module 4 is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
I2C Module 3 Peripheral Ready
Value Description
1
I2C module 3 is ready for access.
0
I2C module 3 is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
July 17, 2013
405
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
2
R2
RO
0
Description
I2C Module 2 Peripheral Ready
Value Description
1
R1
RO
0
1
I2C module 2 is ready for access.
0
I2C module 2 is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
I2C Module 1 Peripheral Ready
Value Description
0
R0
RO
0
1
I2C module 1 is ready for access.
0
I2C module 1 is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
I2C Module 0 Peripheral Ready
Value Description
1
I2C module 0 is ready for access.
0
I2C module 0 is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
406
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 110: Controller Area Network Peripheral Ready (PRCAN), offset
0xA34
The PRCAN register indicates whether the CAN modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCCAN bit is changed. A reset change is initiated if the
corresponding SRCAN bit is changed from 0 to 1.
The PRCAN bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Controller Area Network Peripheral Ready (PRCAN)
Base 0x400F.E000
Offset 0xA34
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RO
0
CAN Module 1 Peripheral Ready
Value Description
0
R0
RO
0
1
CAN module 1 is ready for access.
0
CAN module 1 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
CAN Module 0 Peripheral Ready
Value Description
1
CAN module 0 is ready for access.
0
CAN module 0 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
July 17, 2013
407
Texas Instruments-Production Data
System Control
Register 111: Analog-to-Digital Converter Peripheral Ready (PRADC), offset
0xA38
The PRADC register indicates whether the ADC modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCADC bit is changed. A reset change is initiated if the
corresponding SRADC bit is changed from 0 to 1.
The PRADC bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Analog-to-Digital Converter Peripheral Ready (PRADC)
Base 0x400F.E000
Offset 0xA38
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RO
0
ADC Module 1 Peripheral Ready
Value Description
0
R0
RO
0
1
ADC module 1 is ready for access.
0
ADC module 1 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
ADC Module 0 Peripheral Ready
Value Description
1
ADC module 0 is ready for access.
0
ADC module 0 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
408
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 112: Analog Comparator Peripheral Ready (PRACMP), offset 0xA3C
The PRACMP register indicates whether the analog comparator module is ready to be accessed
by software following a change in status of power, Run mode clocking, or reset. A Run mode clocking
change is initiated if the corresponding RCGCACMP bit is changed. A reset change is initiated if
the corresponding SRACMP bit is changed from 0 to 1.
The PRACMP bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Analog Comparator Peripheral Ready (PRACMP)
Base 0x400F.E000
Offset 0xA3C
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
0
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
RO
0
Analog Comparator Module 0 Peripheral Ready
Value Description
1
The analog comparator module is ready for access.
0
The analog comparator module is not ready for access. It is
unclocked, unpowered, or in the process of completing a reset
sequence.
July 17, 2013
409
Texas Instruments-Production Data
System Control
Register 113: Pulse Width Modulator Peripheral Ready (PRPWM), offset 0xA40
The PRPWM register indicates whether the PWM modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCPWM bit is changed. A reset change is initiated if the
corresponding SRPWM bit is changed from 0 to 1.
The PRPWM bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Pulse Width Modulator Peripheral Ready (PRPWM)
Base 0x400F.E000
Offset 0xA40
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
R1
R0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RO
0
PWM Module 1 Peripheral Ready
Value Description
0
R0
RO
0
1
PWM module 1 is ready for access.
0
PWM module 1 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
PWM Module 0 Peripheral Ready
Value Description
1
PWM module 0 is ready for access.
0
PWM module 0 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
410
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 114: Quadrature Encoder Interface Peripheral Ready (PRQEI), offset
0xA44
The PRQEI register indicates whether the QEI modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCQEI bit is changed. A reset change is initiated if the
corresponding SRQEI bit is changed from 0 to 1.
The PRQEI bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Quadrature Encoder Interface Peripheral Ready (PRQEI)
Base 0x400F.E000
Offset 0xA44
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RO
0
QEI Module 1 Peripheral Ready
Value Description
0
R0
RO
0
1
QEI module 1 is ready for access.
0
QEI module 1 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
QEI Module 0 Peripheral Ready
Value Description
1
QEI module 0 is ready for access.
0
QEI module 0 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
July 17, 2013
411
Texas Instruments-Production Data
System Control
Register 115: EEPROM Peripheral Ready (PREEPROM), offset 0xA58
The PREEPROM register indicates whether the EEPROM module is ready to be accessed by
software following a change in status of power, Run mode clocking, or reset. A Run mode clocking
change is initiated if the corresponding RCGCEEPROM bit is changed. A reset change is initiated
if the corresponding SREEPROM bit is changed from 0 to 1.
The PREEPROM bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
EEPROM Peripheral Ready (PREEPROM)
Base 0x400F.E000
Offset 0xA58
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
0
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
RO
0
EEPROM Module Peripheral Ready
Value Description
1
The EEPROM module is ready for access.
0
The EEPROM module is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
412
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 116: 32/64-Bit Wide General-Purpose Timer Peripheral Ready
(PRWTIMER), offset 0xA5C
The PRWTIMER register indicates whether the timer modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCWTIMER bit is changed. A reset change is initiated if the
corresponding SRWTIMER bit is changed from 0 to 1.
The PRWTIMER bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
32/64-Bit Wide General-Purpose Timer Peripheral Ready (PRWTIMER)
Base 0x400F.E000
Offset 0xA5C
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
RO
0
32/64-Bit Wide General-Purpose Timer 5 Peripheral Ready
Value Description
4
R4
RO
0
1
32/64-bit wide timer module 5 is ready for access.
0
32/64-bit wide timer module 5 is not ready for access. It is
unclocked, unpowered, or in the process of completing a reset
sequence.
32/64-Bit Wide General-Purpose Timer 4 Peripheral Ready
Value Description
3
R3
RO
0
1
32/64-bit wide timer module 4 is ready for access.
0
32/64-bit wide timer module 4 is not ready for access. It is
unclocked, unpowered, or in the process of completing a reset
sequence.
32/64-Bit Wide General-Purpose Timer 3 Peripheral Ready
Value Description
1
32/64-bit wide timer module 3 is ready for access.
0
32/64-bit wide timer module 3 is not ready for access. It is
unclocked, unpowered, or in the process of completing a reset
sequence.
July 17, 2013
413
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
2
R2
RO
0
Description
32/64-Bit Wide General-Purpose Timer 2 Peripheral Ready
Value Description
1
R1
RO
0
1
32/64-bit wide timer module 2 is ready for access.
0
32/64-bit wide timer module 2 is not ready for access. It is
unclocked, unpowered, or in the process of completing a reset
sequence.
32/64-Bit Wide General-Purpose Timer 1 Peripheral Ready
Value Description
0
R0
RO
0
1
32/64-bit wide timer module 1 is ready for access.
0
32/64-bit wide timer module 1 is not ready for access. It is
unclocked, unpowered, or in the process of completing a reset
sequence.
32/64-Bit Wide General-Purpose Timer 0 Peripheral Ready
Value Description
5.6
1
32/64-bit wide timer module 0 is ready for access.
0
32/64-bit wide timer module 0 is not ready for access. It is
unclocked, unpowered, or in the process of completing a reset
sequence.
System Control Legacy Register Descriptions
All addresses given are relative to the System Control base address of 0x400F.E000.
Important: Register in this section are provided for legacy software support only; registers in
“System Control Register Descriptions” on page 228 should be used instead.
414
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 117: Device Capabilities 0 (DC0), offset 0x008
This legacy register is predefined by the part and can be used to verify features.
Important: This register is provided for legacy software support only.
The Flash Size (FSIZE) and SRAM Size (SSIZE) registers should be used to determine
this microcontroller's memory sizes. A read of DC0 correctly identifies legacy memory
sizes but software must use FSIZE and SSIZE for memory sizes that are not listed
below.
Device Capabilities 0 (DC0)
Base 0x400F.E000
Offset 0x008
Type RO, reset 0x007F.003F
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
SRAMSZ
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
FLASHSZ
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:16
SRAMSZ
RO
0x7F
SRAM Size
Indicates the size of the on-chip SRAM.
Value Description
0x7
2 KB of SRAM
0xF
4 KB of SRAM
0x17 6 KB of SRAM
0x1F 8 KB of SRAM
0x2F 12 KB of SRAM
0x3F 16 KB of SRAM
0x4F 20 KB of SRAM
0x5F 24 KB of SRAM
0x7F 32 KB of SRAM
July 17, 2013
415
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
Description
15:0
FLASHSZ
RO
0x3F
Flash Size
Indicates the size of the on-chip Flash memory.
Value Description
0x3
8 KB of Flash
0x7
16 KB of Flash
0xF
32 KB of Flash
0x1F 64 KB of Flash
0x2F 96 KB of Flash
0x3F 128 KB of Flash
0x5F 192 KB of Flash
0x7F 256 KB of Flash
416
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 118: Device Capabilities 1 (DC1), offset 0x010
This register is predefined by the part and can be used to verify features. If any bit is clear in this
register, the module is not present. The corresponding bit in the RCGC0, SCGC0, DCGC0, and the
peripheral-specific RCGC, SCGC, and DCGC registers cannot be set.
Important: This register is provided for legacy software support only.
The Peripheral Present registers should be used to determine which modules are
implemented on this microcontroller. A read of DC1 correctly identifies if a legacy module
is present but software must use the Peripheral Present registers to determine if a
module is present that is not supported by the DCn registers.
Likewise, the ADC Peripheral Properties (ADCPP) register should be used to determine
the maximum ADC sample rate and whether the temperature sensor is present. However,
to support legacy software, the MAXADCnSPD fields and the TEMPSNS bit are available.
A read of DC1 correctly identifies the maximum ADC sample rate for legacy rates and
whether the temperature sensor is present.
Device Capabilities 1 (DC1)
Base 0x400F.E000
Offset 0x010
Type RO, reset 0x1333.2FFF
31
30
29
reserved
Type
Reset
28
WDT1
26
24
23
22
20
19
18
16
CAN1
CAN0
PWM1
PWM0
ADC1
ADC0
RO
1
RO
0
RO
0
RO
1
RO
1
RO
0
RO
0
RO
1
RO
1
RO
0
RO
0
RO
1
RO
1
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
MPU
HIB
TEMPSNS
PLL
WDT0
SWO
SWD
JTAG
RO
0
RO
0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
MAXADC1SPD
MAXADC0SPD
RO
1
RO
1
RO
1
Bit/Field
Name
Type
Reset
31:29
reserved
RO
0
28
WDT1
RO
0x1
RO
1
reserved
17
RO
0
RO
0
reserved
21
RO
0
RO
1
reserved
25
RO
0
MINSYSDIV
Type
Reset
27
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Watchdog Timer1 Present
When set, indicates that watchdog timer 1 is present.
27:26
reserved
RO
0
25
CAN1
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
CAN Module 1 Present
When set, indicates that CAN unit 1 is present.
24
CAN0
RO
0x1
CAN Module 0 Present
When set, indicates that CAN unit 0 is present.
23:22
reserved
RO
0
21
PWM1
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PWM Module 1 Present
When set, indicates that the PWM module is present.
July 17, 2013
417
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
20
PWM0
RO
0x1
Description
PWM Module 0 Present
When set, indicates that the PWM module is present.
19:18
reserved
RO
0
17
ADC1
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
ADC Module 1 Present
When set, indicates that ADC module 1 is present.
16
ADC0
RO
0x1
ADC Module 0 Present
When set, indicates that ADC module 0 is present
15:12
MINSYSDIV
RO
0x2
System Clock Divider
Minimum 4-bit divider value for system clock. The reset value is
hardware-dependent. See the RCC register for how to change the
system clock divisor using the SYSDIV bit.
Value Description
11:10
MAXADC1SPD
RO
0x3
0x1
Specifies an 80-MHz CPU clock with a PLL divider of 2.5.
0x2
Specifies a 66-MHz CPU clock with a PLL divider of 3.
0x3
Specifies a 50-MHz CPU clock with a PLL divider of 4.
0x4
Specifies a 40-MHz CPU clock with a PLL divider of 5.
0x7
Specifies a 25-MHz clock with a PLL divider of 8.
0x9
Specifies a 20-MHz clock with a PLL divider of 10.
Max ADC1 Speed
This field indicates the maximum rate at which the ADC samples data.
Value Description
9:8
MAXADC0SPD
RO
0x3
0x3
1M samples/second
0x2
500K samples/second
0x1
250K samples/second
0x0
125K samples/second
Max ADC0 Speed
This field indicates the maximum rate at which the ADC samples data.
Value Description
7
MPU
RO
0x1
0x3
1M samples/second
0x2
500K samples/second
0x1
250K samples/second
0x0
125K samples/second
MPU Present
When set, indicates that the Cortex-M4F Memory Protection Unit (MPU)
module is present. See the "Cortex-M4F Peripherals" chapter for details
on the MPU.
418
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
6
HIB
RO
0x1
Description
Hibernation Module Present
When set, indicates that the Hibernation module is present.
5
TEMPSNS
RO
0x1
Temp Sensor Present
When set, indicates that the on-chip temperature sensor is present.
4
PLL
RO
0x1
PLL Present
When set, indicates that the on-chip Phase Locked Loop (PLL) is
present.
3
WDT0
RO
0x1
Watchdog Timer 0 Present
When set, indicates that watchdog timer 0 is present.
2
SWO
RO
0x1
SWO Trace Port Present
When set, indicates that the Serial Wire Output (SWO) trace port is
present.
1
SWD
RO
0x1
SWD Present
When set, indicates that the Serial Wire Debugger (SWD) is present.
0
JTAG
RO
0x1
JTAG Present
When set, indicates that the JTAG debugger interface is present.
July 17, 2013
419
Texas Instruments-Production Data
System Control
Register 119: Device Capabilities 2 (DC2), offset 0x014
This register is predefined by the part and can be used to verify features. If any bit is clear in this
register, the module is not present. The corresponding bit in the RCGC1, SCGC1, DCGC1, and the
peripheral-specific RCGC, SCGC, and DCGC registers registers cannot be set.
Important: This register is provided for legacy software support only.
The Peripheral Present registers should be used to determine which modules are
implemented on this microcontroller. A read of DC2 correctly identifies if a legacy module
is present but software must use the Peripheral Present registers to determine if a
module is present that is not supported by the DCn registers.
Note that the Analog Comparator Peripheral Present (PPACMP) register identifies
whether the analog comparator module is present. The Analog Comparator Peripheral
Properties (ACMPPP) register indicates how many analog comparator blocks are
present in the module.
Device Capabilities 2 (DC2)
Base 0x400F.E000
Offset 0x014
Type RO, reset 0x070F.F337
Type
Reset
Type
Reset
31
30
29
28
27
26
25
24
reserved
EPI0
reserved
I2S0
reserved
COMP2
COMP1
COMP0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
15
14
13
12
11
10
I2C1HS
I2C1
I2C0HS
I2C0
RO
1
RO
1
RO
1
RO
1
reserved
RO
0
RO
0
23
22
RO
1
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
QEI1
QEI0
RO
1
RO
1
Bit/Field
Name
Type
Reset
31
reserved
RO
0
30
EPI0
RO
0x0
21
20
19
18
17
16
TIMER3
TIMER2
TIMER1
TIMER0
RO
1
RO
1
RO
1
RO
1
4
3
2
1
0
SSI1
SSI0
reserved
UART2
UART1
UART0
RO
1
RO
1
RO
0
RO
1
RO
1
RO
1
reserved
reserved
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
EPI Module 0 Present
When set, indicates that EPI module 0 is present.
29
reserved
RO
0
28
I2S0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2S Module 0 Present
When set, indicates that I2S module 0 is present.
27
reserved
RO
0
26
COMP2
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Analog Comparator 2 Present
When set, indicates that analog comparator 2 is present.
25
COMP1
RO
0x1
Analog Comparator 1 Present
When set, indicates that analog comparator 1 is present.
420
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
24
COMP0
RO
0x1
Description
Analog Comparator 0 Present
When set, indicates that analog comparator 0 is present.
23:20
reserved
RO
0
19
TIMER3
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Timer Module 3 Present
When set, indicates that General-Purpose Timer module 3 is present.
18
TIMER2
RO
0x1
Timer Module 2 Present
When set, indicates that General-Purpose Timer module 2 is present.
17
TIMER1
RO
0x1
Timer Module 1 Present
When set, indicates that General-Purpose Timer module 1 is present.
16
TIMER0
RO
0x1
Timer Module 0 Present
When set, indicates that General-Purpose Timer module 0 is present.
15
I2C1HS
RO
0x1
I2C Module 1 Speed
When set, indicates that I2C module 1 can operate in high-speed mode.
14
I2C1
RO
0x1
I2C Module 1 Present
When set, indicates that I2C module 1 is present.
13
I2C0HS
RO
0x1
I2C Module 0 Speed
When set, indicates that I2C module 0 can operate in high-speed mode.
12
I2C0
RO
0x1
I2C Module 0 Present
When set, indicates that I2C module 0 is present.
11:10
reserved
RO
0
9
QEI1
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
QEI Module 1 Present
When set, indicates that QEI module 1 is present.
8
QEI0
RO
0x1
QEI Module 0 Present
When set, indicates that QEI module 0 is present.
7:6
reserved
RO
0
5
SSI1
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
SSI Module 1 Present
When set, indicates that SSI module 1 is present.
4
SSI0
RO
0x1
SSI Module 0 Present
When set, indicates that SSI module 0 is present.
3
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
421
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
2
UART2
RO
0x1
Description
UART Module 2 Present
When set, indicates that UART module 2 is present.
1
UART1
RO
0x1
UART Module 1 Present
When set, indicates that UART module 1 is present.
0
UART0
RO
0x1
UART Module 0 Present
When set, indicates that UART module 0 is present.
422
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 120: Device Capabilities 3 (DC3), offset 0x018
This register is predefined by the part and can be used to verify features. If any bit is clear in this
register, the feature is not present.
Important: This register is provided for legacy software support only.
For some modules, the peripheral-resident Peripheral Properties registers should be
used to determine which pins are available on this microcontroller. A read of DC3
correctly identifies if a legacy pin is present but software must use the Peripheral
Properties registers to determine if a pin is present that is not supported by the DCn
registers.
Device Capabilities 3 (DC3)
Base 0x400F.E000
Offset 0x018
Type RO, reset 0xBFFF.FFFF
Type
Reset
Type
Reset
31
30
29
28
27
26
25
24
32KHZ
reserved
CCP5
CCP4
CCP3
CCP2
CCP1
CCP0
RO
1
RO
0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
13
12
10
9
15
14
PWMFAULT
C2O
RO
1
RO
1
C2PLUS C2MINUS
RO
1
RO
1
11
C1O
C1PLUS C1MINUS
RO
1
RO
1
RO
1
Bit/Field
Name
Type
Reset
31
32KHZ
RO
0x1
23
8
C0O
22
21
20
19
18
17
16
ADC0AIN7 ADC0AIN6 ADC0AIN5 ADC0AIN4 ADC0AIN3 ADC0AIN2 ADC0AIN1 ADC0AIN0
RO
1
RO
1
7
6
C0PLUS C0MINUS
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
5
4
3
2
1
0
PWM5
PWM4
PWM3
PWM2
PWM1
PWM0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
32KHz Input Clock Available
When set, indicates an even CCP pin is present and can be used as a
32-KHz input clock.
Note:
30
reserved
RO
0
29
CCP5
RO
0x1
The GPTMPP register does not provide this information.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
T2CCP1 Pin Present
When set, indicates that Capture/Compare/PWM pin T2CCP1 is present.
Note:
28
CCP4
RO
0x1
The GPTMPP register does not provide this information.
T2CCP0 Pin Present
When set, indicates that Capture/Compare/PWM pin T2CCP0 is present.
Note:
27
CCP3
RO
0x1
The GPTMPP register does not provide this information.
T1CCP1 Pin Present
When set, indicates that Capture/Compare/PWM pin T1CCP1 is present.
Note:
26
CCP2
RO
0x1
The GPTMPP register does not provide this information.
T1CCP0 Pin Present
When set, indicates that Capture/Compare/PWM pin T1CCP0 is present.
Note:
The GPTMPP register does not provide this information.
July 17, 2013
423
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
25
CCP1
RO
0x1
Description
T0CCP1 Pin Present
When set, indicates that Capture/Compare/PWM pin T0CCP1 is present.
Note:
24
CCP0
RO
0x1
The GPTMPP register does not provide this information.
T0CCP0 Pin Present
When set, indicates that Capture/Compare/PWM pin T0CCP0 is present.
Note:
23
ADC0AIN7
RO
0x1
The GPTMPP register does not provide this information.
ADC Module 0 AIN7 Pin Present
When set, indicates that ADC module 0 input pin 7 is present.
Note:
22
ADC0AIN6
RO
0x1
The CH field in the ADCPP register provides this information.
ADC Module 0 AIN6 Pin Present
When set, indicates that ADC module 0 input pin 6 is present.
Note:
21
ADC0AIN5
RO
0x1
The CH field in the ADCPP register provides this information.
ADC Module 0 AIN5 Pin Present
When set, indicates that ADC module 0 input pin 5 is present.
Note:
20
ADC0AIN4
RO
0x1
The CH field in the ADCPP register provides this information.
ADC Module 0 AIN4 Pin Present
When set, indicates that ADC module 0 input pin 4 is present.
Note:
19
ADC0AIN3
RO
0x1
The CH field in the ADCPP register provides this information.
ADC Module 0 AIN3 Pin Present
When set, indicates that ADC module 0 input pin 3 is present.
Note:
18
ADC0AIN2
RO
0x1
The CH field in the ADCPP register provides this information.
ADC Module 0 AIN2 Pin Present
When set, indicates that ADC module 0 input pin 2 is present.
Note:
17
ADC0AIN1
RO
0x1
The CH field in the ADCPP register provides this information.
ADC Module 0 AIN1 Pin Present
When set, indicates that ADC module 0 input pin 1 is present.
Note:
16
ADC0AIN0
RO
0x1
The CH field in the ADCPP register provides this information.
ADC Module 0 AIN0 Pin Present
When set, indicates that ADC module 0 input pin 0 is present.
Note:
15
PWMFAULT
RO
0x1
The CH field in the ADCPP register provides this information.
PWM Fault Pin Present
When set, indicates that a PWM Fault pin is present. See DC5 for
specific Fault pins on this device.
Note:
14
C2O
RO
0x1
The FCNT field in the PWMPP register provides this
information.
C2o Pin Present
When set, indicates that the analog comparator 2 output pin is present.
Note:
The C2O bit in the ACMPPP register provides this information.
424
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
13
C2PLUS
RO
0x1
Description
C2+ Pin Present
When set, indicates that the analog comparator 2 (+) input pin is present.
Note:
12
C2MINUS
RO
0x1
This pin is present when analog comparator 2 is present.
C2- Pin Present
When set, indicates that the analog comparator 2 (-) input pin is present.
Note:
11
C1O
RO
0x1
This pin is present when analog comparator 2 is present.
C1o Pin Present
When set, indicates that the analog comparator 1 output pin is present.
Note:
10
C1PLUS
RO
0x1
The C1O bit in the ACMPPP register provides this information.
C1+ Pin Present
When set, indicates that the analog comparator 1 (+) input pin is present.
Note:
9
C1MINUS
RO
0x1
This pin is present when analog comparator 1 is present.
C1- Pin Present
When set, indicates that the analog comparator 1 (-) input pin is present.
Note:
8
C0O
RO
0x1
This pin is present when analog comparator 1 is present.
C0o Pin Present
When set, indicates that the analog comparator 0 output pin is present.
Note:
7
C0PLUS
RO
0x1
The C0O bit in the ACMPPP register provides this information.
C0+ Pin Present
When set, indicates that the analog comparator 0 (+) input pin is present.
Note:
6
C0MINUS
RO
0x1
This pin is present when analog comparator 0 is present.
C0- Pin Present
When set, indicates that the analog comparator 0 (-) input pin is present.
Note:
5
PWM5
RO
0x1
This pin is present when analog comparator 0 is present.
PWM5 Pin Present
When set, indicates that the PWM pin 5 is present.
Note:
4
PWM4
RO
0x1
The GCNT field in the PWMPP register provides this
information.
PWM4 Pin Present
When set, indicates that the PWM pin 4 is present.
Note:
3
PWM3
RO
0x1
The GCNT field in the PWMPP register provides this
information.
PWM3 Pin Present
When set, indicates that the PWM pin 3 is present.
Note:
The GCNT field in the PWMPP register provides this
information.
July 17, 2013
425
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
2
PWM2
RO
0x1
Description
PWM2 Pin Present
When set, indicates that the PWM pin 2 is present.
Note:
1
PWM1
RO
0x1
The GCNT field in the PWMPP register provides this
information.
PWM1 Pin Present
When set, indicates that the PWM pin 1 is present.
Note:
0
PWM0
RO
0x1
The GCNT field in the PWMPP register provides this
information.
PWM0 Pin Present
When set, indicates that the PWM pin 0 is present.
Note:
The GCNT field in the PWMPP register provides this
information.
426
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 121: Device Capabilities 4 (DC4), offset 0x01C
This register is predefined by the part and can be used to verify features. If any bit is clear in this
register, the module is not present. The corresponding bit in the RCGC2, SCGC2, DCGC2, and the
peripheral-specific RCGC, SCGC, and DCGC registers registers cannot be set.
Important: This register is provided for legacy software support only.
The Peripheral Present registers should be used to determine which modules are
implemented on this microcontroller. A read of DC4 correctly identifies if a legacy module
is present but software must use the Peripheral Present registers to determine if a
module is present that is not supported by the DCn registers.
The peripheral-resident Peripheral Properties registers should be used to determine
which pins and features are available on this microcontroller. A read of DC4 correctly
identifies if a legacy pin or feature is present. Software must use the Peripheral Properties
registers to determine if a pin or feature is present that is not supported by the DCn
registers.
Device Capabilities 4 (DC4)
Base 0x400F.E000
Offset 0x01C
Type RO, reset 0x0004.F1FF
Type
Reset
Type
Reset
31
30
29
28
27
26
25
reserved
EPHY0
reserved
EMAC0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
CCP7
CCP6
UDMA
ROM
RO
1
RO
1
RO
1
RO
1
reserved
RO
0
23
22
20
19
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
0
RO
0
8
7
6
5
4
3
2
1
0
GPIOJ
RO
1
GPIOH
GPIOG
GPIOF
GPIOE
GPIOD
GPIOC
GPIOB
GPIOA
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
E1588
reserved
RO
0
24
RO
0
Bit/Field
Name
Type
Reset
31
reserved
RO
0
30
EPHY0
RO
0x0
21
reserved
18
17
PICAL
16
reserved
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Ethernet PHY Layer 0 Present
When set, indicates that Ethernet PHY layer 0 is present.
29
reserved
RO
0
28
EMAC0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Ethernet MAC Layer 0 Present
When set, indicates that Ethernet MAC layer 0 is present.
27:25
reserved
RO
0
24
E1588
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1588 Capable
When set, indicates that Ethernet MAC layer 0 is 1588 capable.
July 17, 2013
427
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
23:19
reserved
RO
0
18
PICAL
RO
0x1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PIOSC Calibrate
When set, indicates that the PIOSC can be calibrated by software.
17:16
reserved
RO
0
15
CCP7
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
T3CCP1 Pin Present
When set, indicates that Capture/Compare/PWM pin T3CCP1 is present.
Note:
14
CCP6
RO
0x1
The GPTMPP register does not provide this information.
T3CCP0 Pin Present
When set, indicates that Capture/Compare/PWM pin T3CCP0 is present.
Note:
13
UDMA
RO
0x1
The GPTMPP register does not provide this information.
Micro-DMA Module Present
When set, indicates that the micro-DMA module present.
12
ROM
RO
0x1
Internal Code ROM Present
When set, indicates that internal code ROM is present.
11:9
reserved
RO
0
8
GPIOJ
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
GPIO Port J Present
When set, indicates that GPIO Port J is present.
7
GPIOH
RO
0x1
GPIO Port H Present
When set, indicates that GPIO Port H is present.
6
GPIOG
RO
0x1
GPIO Port G Present
When set, indicates that GPIO Port G is present.
5
GPIOF
RO
0x1
GPIO Port F Present
When set, indicates that GPIO Port F is present.
4
GPIOE
RO
0x1
GPIO Port E Present
When set, indicates that GPIO Port E is present.
3
GPIOD
RO
0x1
GPIO Port D Present
When set, indicates that GPIO Port D is present.
2
GPIOC
RO
0x1
GPIO Port C Present
When set, indicates that GPIO Port C is present.
1
GPIOB
RO
0x1
GPIO Port B Present
When set, indicates that GPIO Port B is present.
428
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
0
GPIOA
RO
0x1
Description
GPIO Port A Present
When set, indicates that GPIO Port A is present.
July 17, 2013
429
Texas Instruments-Production Data
System Control
Register 122: Device Capabilities 5 (DC5), offset 0x020
This register is predefined by the part and can be used to verify PWM features. If any bit is clear in
this register, the module is not present.
Important: This register is provided for legacy software support only.
The PWM Peripheral Properties (PWMPP) register should be used to determine what
pins and features are available on PWM modules. A read of this register correctly
identifies if a legacy pin or feature is present. Software must use the PWMPP register
to determine if a pin or feature that is not supported by the DCn registers is present.
Device Capabilities 5 (DC5)
Base 0x400F.E000
Offset 0x020
Type RO, reset 0x0F30.00FF
31
30
29
28
reserved
Type
Reset
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
RO
1
RO
1
15
14
13
12
11
10
9
8
reserved
Type
Reset
RO
0
RO
0
23
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:28
reserved
RO
0
27
PWMFAULT3
RO
0x1
RO
0
22
reserved
PWMFAULT3 PWMFAULT2 PWMFAULT1 PWMFAULT0
RO
0
21
20
19
18
PWMEFLT PWMESYNC
RO
0
RO
1
RO
1
17
16
reserved
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
PWM7
PWM6
PWM5
PWM4
PWM3
PWM2
PWM1
PWM0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PWM Fault 3 Pin Present
When set, indicates that the PWM Fault 3 pin is present.
26
PWMFAULT2
RO
0x1
PWM Fault 2 Pin Present
When set, indicates that the PWM Fault 2 pin is present.
25
PWMFAULT1
RO
0x1
PWM Fault 1 Pin Present
When set, indicates that the PWM Fault 1 pin is present.
24
PWMFAULT0
RO
0x1
PWM Fault 0 Pin Present
When set, indicates that the PWM Fault 0 pin is present.
23:22
reserved
RO
0
21
PWMEFLT
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PWM Extended Fault Active
When set, indicates that the PWM Extended Fault feature is active.
20
PWMESYNC
RO
0x1
PWM Extended SYNC Active
When set, indicates that the PWM Extended SYNC feature is active.
19:8
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
430
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
7
PWM7
RO
0x1
Description
PWM7 Pin Present
When set, indicates that the PWM pin 7 is present.
6
PWM6
RO
0x1
PWM6 Pin Present
When set, indicates that the PWM pin 6 is present.
5
PWM5
RO
0x1
PWM5 Pin Present
When set, indicates that the PWM pin 5 is present.
4
PWM4
RO
0x1
PWM4 Pin Present
When set, indicates that the PWM pin 4 is present.
3
PWM3
RO
0x1
PWM3 Pin Present
When set, indicates that the PWM pin 3 is present.
2
PWM2
RO
0x1
PWM2 Pin Present
When set, indicates that the PWM pin 2 is present.
1
PWM1
RO
0x1
PWM1 Pin Present
When set, indicates that the PWM pin 1 is present.
0
PWM0
RO
0x1
PWM0 Pin Present
When set, indicates that the PWM pin 0 is present.
July 17, 2013
431
Texas Instruments-Production Data
System Control
Register 123: Device Capabilities 6 (DC6), offset 0x024
This register is predefined by the part and can be used to verify features. If any bit is clear in this
register, the module is not present. The corresponding bit in the RCGC0, SCGC0, and DCGC0
registers cannot be set.
Important: This register is provided for legacy software support only.
The USB Peripheral Properties (USBPP) register should be used to determine what
features are available on the USB module. A read of this register correctly identifies if
a legacy feature is present. Software must use the USBPP register to determine if a
pin or feature that is not supported by the DCn registers is present.
Device Capabilities 6 (DC6)
Base 0x400F.E000
Offset 0x024
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
10
9
8
7
6
5
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
USB0PHY
RO
0
Bit/Field
Name
Type
Reset
31:5
reserved
RO
0
4
USB0PHY
RO
0x0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
RO
0
RO
0
0
USB0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
USB Module 0 PHY Present
When set, indicates that the USB module 0 PHY is present.
3:2
reserved
RO
0
1:0
USB0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
USB Module 0 Present
This field indicates that USB module 0 is present and specifies its
capability.
sysValue Description
0x0
NA
USB0 is not present.
0x1
DEVICE
USB0 is Device Only.
0x2
HOST
USB0 is Device or Host.
0x3
OTG
USB0 is OTG.
432
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 124: Device Capabilities 7 (DC7), offset 0x028
This register is predefined by the part and can be used to verify μDMA channel features. A 1 indicates
the channel is available on this device; a 0 that the channel is only available on other devices in the
family. Channels can have multiple assignments, see “Channel Assignments” on page 578 for more
information.
Important: This register is provided for legacy software support only. The DMACHANS bit field in
the DMA Status (DMASTAT) register indicates the number of DMA channels.
Device Capabilities 7 (DC7)
Base 0x400F.E000
Offset 0x028
Type RO, reset 0xFFFF.FFFF
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
reserved DMACH30 DMACH29 DMACH28 DMACH27 DMACH26 DMACH25 DMACH24 DMACH23 DMACH22 DMACH21 DMACH20 DMACH19 DMACH18 DMACH17 DMACH16
Type
Reset
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
DMACH15 DMACH14 DMACH13 DMACH12 DMACH11 DMACH10 DMACH9 DMACH8 DMACH7 DMACH6 DMACH5 DMACH4 DMACH3 DMACH2 DMACH1 DMACH0
Type
Reset
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Bit/Field
Name
Type
Reset
31
reserved
RO
0x1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
DMA Channel 31
When set, indicates μDMA channel 31 is available.
30
DMACH30
RO
0x1
DMA Channel 30
When set, indicates μDMA channel 30 is available.
29
DMACH29
RO
0x1
DMA Channel 29
When set, indicates μDMA channel 29 is available.
28
DMACH28
RO
0x1
DMA Channel 28
When set, indicates μDMA channel 28 is available.
27
DMACH27
RO
0x1
DMA Channel 27
When set, indicates μDMA channel 27 is available.
26
DMACH26
RO
0x1
DMA Channel 26
When set, indicates μDMA channel 26 is available.
25
DMACH25
RO
0x1
DMA Channel 25
When set, indicates μDMA channel 25 is available.
24
DMACH24
RO
0x1
DMA Channel 24
When set, indicates μDMA channel 24 is available.
23
DMACH23
RO
0x1
DMA Channel 23
When set, indicates μDMA channel 23 is available.
22
DMACH22
RO
0x1
DMA Channel 22
When set, indicates μDMA channel 22 is available.
July 17, 2013
433
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
21
DMACH21
RO
0x1
Description
DMA Channel 21
When set, indicates μDMA channel 21 is available.
20
DMACH20
RO
0x1
DMA Channel 20
When set, indicates μDMA channel 20 is available.
19
DMACH19
RO
0x1
DMA Channel 19
When set, indicates μDMA channel 19 is available.
18
DMACH18
RO
0x1
DMA Channel 18
When set, indicates μDMA channel 18 is available.
17
DMACH17
RO
0x1
DMA Channel 17
When set, indicates μDMA channel 17 is available.
16
DMACH16
RO
0x1
DMA Channel 16
When set, indicates μDMA channel 16 is available.
15
DMACH15
RO
0x1
DMA Channel 15
When set, indicates μDMA channel 15 is available.
14
DMACH14
RO
0x1
DMA Channel 14
When set, indicates μDMA channel 14 is available.
13
DMACH13
RO
0x1
DMA Channel 13
When set, indicates μDMA channel 13 is available.
12
DMACH12
RO
0x1
DMA Channel 12
When set, indicates μDMA channel 12 is available.
11
DMACH11
RO
0x1
DMA Channel 11
When set, indicates μDMA channel 11 is available.
10
DMACH10
RO
0x1
DMA Channel 10
When set, indicates μDMA channel 10 is available.
9
DMACH9
RO
0x1
DMA Channel 9
When set, indicates μDMA channel 9 is available.
8
DMACH8
RO
0x1
DMA Channel 8
When set, indicates μDMA channel 8 is available.
7
DMACH7
RO
0x1
DMA Channel 7
When set, indicates μDMA channel 7 is available.
6
DMACH6
RO
0x1
DMA Channel 6
When set, indicates μDMA channel 6 is available.
5
DMACH5
RO
0x1
DMA Channel 5
When set, indicates μDMA channel 5 is available.
4
DMACH4
RO
0x1
DMA Channel 4
When set, indicates μDMA channel 4 is available.
434
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
3
DMACH3
RO
0x1
Description
DMA Channel 3
When set, indicates μDMA channel 3 is available.
2
DMACH2
RO
0x1
DMA Channel 2
When set, indicates μDMA channel 2 is available.
1
DMACH1
RO
0x1
DMA Channel 1
When set, indicates μDMA channel 1 is available.
0
DMACH0
RO
0x1
DMA Channel 0
When set, indicates μDMA channel 0 is available.
July 17, 2013
435
Texas Instruments-Production Data
System Control
Register 125: Device Capabilities 8 (DC8), offset 0x02C
This register is predefined by the part and can be used to verify features.
Important: This register is provided for legacy software support only.
The ADC Peripheral Properties (ADCPP) register should be used to determine how
many input channels are available on the ADC module. A read of this register correctly
identifies if legacy channels are present but software must use the ADCPP register to
determine if a channel is present that is not supported by the DCn registers.
Device Capabilities 8 (DC8)
Base 0x400F.E000
Offset 0x02C
Type RO, reset 0xFFFF.FFFF
Type
Reset
Type
Reset
31
30
29
28
27
26
ADC1AIN15
ADC1AIN14
ADC1AIN13
ADC1AIN12
ADC1AIN11
ADC1AIN10
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
15
14
13
12
11
10
ADC0AIN15
ADC0AIN14
ADC0AIN13
ADC0AIN12
ADC0AIN11
ADC0AIN10
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
25
24
23
22
21
20
19
18
17
16
ADC1AIN9 ADC1AIN8 ADC1AIN7 ADC1AIN6 ADC1AIN5 ADC1AIN4 ADC1AIN3 ADC1AIN2 ADC1AIN1 ADC1AIN0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
9
8
7
6
5
4
3
2
1
0
ADC0AIN9 ADC0AIN8 ADC0AIN7 ADC0AIN6 ADC0AIN5 ADC0AIN4 ADC0AIN3 ADC0AIN2 ADC0AIN1 ADC0AIN0
RO
1
Bit/Field
Name
Type
Reset
31
ADC1AIN15
RO
0x1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
ADC Module 1 AIN15 Pin Present
When set, indicates that ADC module 1 input pin 15 is present.
30
ADC1AIN14
RO
0x1
ADC Module 1 AIN14 Pin Present
When set, indicates that ADC module 1 input pin 14 is present.
29
ADC1AIN13
RO
0x1
ADC Module 1 AIN13 Pin Present
When set, indicates that ADC module 1 input pin 13 is present.
28
ADC1AIN12
RO
0x1
ADC Module 1 AIN12 Pin Present
When set, indicates that ADC module 1 input pin 12 is present.
27
ADC1AIN11
RO
0x1
ADC Module 1 AIN11 Pin Present
When set, indicates that ADC module 1 input pin 11 is present.
26
ADC1AIN10
RO
0x1
ADC Module 1 AIN10 Pin Present
When set, indicates that ADC module 1 input pin 10 is present.
25
ADC1AIN9
RO
0x1
ADC Module 1 AIN9 Pin Present
When set, indicates that ADC module 1 input pin 9 is present.
24
ADC1AIN8
RO
0x1
ADC Module 1 AIN8 Pin Present
When set, indicates that ADC module 1 input pin 8 is present.
23
ADC1AIN7
RO
0x1
ADC Module 1 AIN7 Pin Present
When set, indicates that ADC module 1 input pin 7 is present.
22
ADC1AIN6
RO
0x1
ADC Module 1 AIN6 Pin Present
When set, indicates that ADC module 1 input pin 6 is present.
436
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
21
ADC1AIN5
RO
0x1
Description
ADC Module 1 AIN5 Pin Present
When set, indicates that ADC module 1 input pin 5 is present.
20
ADC1AIN4
RO
0x1
ADC Module 1 AIN4 Pin Present
When set, indicates that ADC module 1 input pin 4 is present.
19
ADC1AIN3
RO
0x1
ADC Module 1 AIN3 Pin Present
When set, indicates that ADC module 1 input pin 3 is present.
18
ADC1AIN2
RO
0x1
ADC Module 1 AIN2 Pin Present
When set, indicates that ADC module 1 input pin 2 is present.
17
ADC1AIN1
RO
0x1
ADC Module 1 AIN1 Pin Present
When set, indicates that ADC module 1 input pin 1 is present.
16
ADC1AIN0
RO
0x1
ADC Module 1 AIN0 Pin Present
When set, indicates that ADC module 1 input pin 0 is present.
15
ADC0AIN15
RO
0x1
ADC Module 0 AIN15 Pin Present
When set, indicates that ADC module 0 input pin 15 is present.
14
ADC0AIN14
RO
0x1
ADC Module 0 AIN14 Pin Present
When set, indicates that ADC module 0 input pin 14 is present.
13
ADC0AIN13
RO
0x1
ADC Module 0 AIN13 Pin Present
When set, indicates that ADC module 0 input pin 13 is present.
12
ADC0AIN12
RO
0x1
ADC Module 0 AIN12 Pin Present
When set, indicates that ADC module 0 input pin 12 is present.
11
ADC0AIN11
RO
0x1
ADC Module 0 AIN11 Pin Present
When set, indicates that ADC module 0 input pin 11 is present.
10
ADC0AIN10
RO
0x1
ADC Module 0 AIN10 Pin Present
When set, indicates that ADC module 0 input pin 10 is present.
9
ADC0AIN9
RO
0x1
ADC Module 0 AIN9 Pin Present
When set, indicates that ADC module 0 input pin 9 is present.
8
ADC0AIN8
RO
0x1
ADC Module 0 AIN8 Pin Present
When set, indicates that ADC module 0 input pin 8 is present.
7
ADC0AIN7
RO
0x1
ADC Module 0 AIN7 Pin Present
When set, indicates that ADC module 0 input pin 7 is present.
6
ADC0AIN6
RO
0x1
ADC Module 0 AIN6 Pin Present
When set, indicates that ADC module 0 input pin 6 is present.
5
ADC0AIN5
RO
0x1
ADC Module 0 AIN5 Pin Present
When set, indicates that ADC module 0 input pin 5 is present.
4
ADC0AIN4
RO
0x1
ADC Module 0 AIN4 Pin Present
When set, indicates that ADC module 0 input pin 4 is present.
July 17, 2013
437
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
3
ADC0AIN3
RO
0x1
Description
ADC Module 0 AIN3 Pin Present
When set, indicates that ADC module 0 input pin 3 is present.
2
ADC0AIN2
RO
0x1
ADC Module 0 AIN2 Pin Present
When set, indicates that ADC module 0 input pin 2 is present.
1
ADC0AIN1
RO
0x1
ADC Module 0 AIN1 Pin Present
When set, indicates that ADC module 0 input pin 1 is present.
0
ADC0AIN0
RO
0x1
ADC Module 0 AIN0 Pin Present
When set, indicates that ADC module 0 input pin 0 is present.
438
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 126: Software Reset Control 0 (SRCR0), offset 0x040
This register allows individual modules to be reset. Writes to this register are masked by the bits in
the Device Capabilities 1 (DC1) register.
Important: This register is provided for legacy software support only.
The peripheral-specific Software Reset registers (such as SRWD) should be used to
reset specific peripherals. A write to this legacy register also writes the corresponding
bit in the peripheral-specific register. Any bits that are changed by writing to this legacy
register can be read back correctly with a read of this register. Software must use the
peripheral-specific registers to support modules that are not present in the legacy
registers. If software uses a peripheral-specific register to write a legacy peripheral
(such as Watchdog 1), the write causes proper operation, but the value of that bit is not
reflected in this register. If software uses both legacy and peripheral-specific register
accesses, the peripheral-specific registers must be accessed by read-modify-write
operations that affect only peripherals that are not present in the legacy registers. In
this manner, both the peripheral-specific and legacy registers have coherent information.
Software Reset Control 0 (SRCR0)
Base 0x400F.E000
Offset 0x040
Type RO, reset 0x0000.0000
31
30
29
reserved
Type
Reset
28
WDT1
RO
0
RO
0
RO
0
RO
0
15
14
13
12
27
26
reserved
25
24
CAN1
CAN0
23
RO
0
RO
0
RO
0
RO
0
RO
0
11
10
9
8
7
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
22
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:29
reserved
RO
0
28
WDT1
RO
0x0
RO
0
RO
0
20
RO
0
RO
0
6
5
4
RO
0
19
PWM0
RO
0
HIB
RO
0
21
reserved
reserved
RO
0
RO
0
18
reserved
RO
0
RO
0
3
2
WDT0
RO
0
17
16
ADC1
ADC0
RO
0
RO
0
1
0
reserved
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
WDT1 Reset Control
When this bit is set, Watchdog Timer module 1 is reset. All internal data
is lost and the registers are returned to their reset states. This bit must
be manually cleared after being set.
27:26
reserved
RO
0
25
CAN1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
CAN1 Reset Control
When this bit is set, CAN module 1 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
24
CAN0
RO
0x0
CAN0 Reset Control
When this bit is set, CAN module 0 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
July 17, 2013
439
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
23:21
reserved
RO
0
20
PWM0
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PWM Reset Control
When this bit is set, PWM module 0 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
19:18
reserved
RO
0
17
ADC1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
ADC1 Reset Control
When this bit is set, ADC module 1 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
16
ADC0
RO
0x0
ADC0 Reset Control
When this bit is set, ADC module 0 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
15:7
reserved
RO
0
6
HIB
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
HIB Reset Control
When this bit is set, the Hibernation module is reset. All internal data is
lost and the registers are returned to their reset states. This bit must be
manually cleared after being set.
5:4
reserved
RO
0
3
WDT0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
WDT0 Reset Control
When this bit is set, Watchdog Timer module 0 is reset. All internal data
is lost and the registers are returned to their reset states. This bit must
be manually cleared after being set.
2:0
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
440
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 127: Software Reset Control 1 (SRCR1), offset 0x044
This register allows individual modules to be reset. Writes to this register are masked by the bits in
the Device Capabilities 2 (DC2) register.
Important: This register is provided for legacy software support only.
The peripheral-specific Software Reset registers (such as SRTIMER) should be used
to reset specific peripherals. A write to this register also writes the corresponding bit in
the peripheral-specific register. Any bits that are changed by writing to this register can
be read back correctly with a read of this register. Software must use the
peripheral-specific registers to support modules that are not present in the legacy
registers. If software uses a peripheral-specific register to write a legacy peripheral
(such as TIMER0), the write causes proper operation, but the value of that bit is not
reflected in this register. If software uses both legacy and peripheral-specific register
accesses, the peripheral-specific registers must be accessed by read-modify-write
operations that affect only peripherals that are not present in the legacy registers. In
this manner, both the peripheral-specific and legacy registers have coherent information.
Note that the Software Reset Analog Comparator (SRACMP) register has only one
bit to set the analog comparator module. Resetting the module resets all the blocks. If
any of the COMPn bits are set, the entire analog comparator module is reset. It is not
possible to reset the blocks individually.
Software Reset Control 1 (SRCR1)
Base 0x400F.E000
Offset 0x044
Type RO, reset 0x0000.0000
31
30
RO
0
RO
0
15
29
28
27
RO
0
RO
0
RO
0
14
13
12
11
reserved
I2C1
reserved
I2C0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
Type
Reset
26
25
24
COMP2
COMP1
COMP0
RO
0
RO
0
10
reserved
RO
0
RO
0
23
22
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
QEI1
QEI0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:27
reserved
RO
0
26
COMP2
RO
0x0
21
20
19
18
17
16
TIMER3
TIMER2
TIMER1
TIMER0
RO
0
RO
0
RO
0
RO
0
4
3
2
1
0
SSI1
SSI0
reserved
UART2
UART1
UART0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
reserved
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Analog Comp 2 Reset Control
When this bit is set, Analog Comparator module 2 is reset. All internal
data is lost and the registers are returned to their reset states. This bit
must be manually cleared after being set.
25
COMP1
RO
0x0
Analog Comp 1 Reset Control
When this bit is set, Analog Comparator module 1 is reset. All internal
data is lost and the registers are returned to their reset states. This bit
must be manually cleared after being set.
July 17, 2013
441
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
24
COMP0
RO
0x0
Description
Analog Comp 0 Reset Control
When this bit is set, Analog Comparator module 0 is reset. All internal
data is lost and the registers are returned to their reset states. This bit
must be manually cleared after being set.
23:20
reserved
RO
0
19
TIMER3
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Timer 3 Reset Control
Timer 3 Reset Control. When this bit is set, General-Purpose Timer
module 3 is reset. All internal data is lost and the registers are returned
to their reset states. This bit must be manually cleared after being set.
18
TIMER2
RO
0x0
Timer 2 Reset Control
When this bit is set, General-Purpose Timer module 2 is reset. All internal
data is lost and the registers are returned to their reset states. This bit
must be manually cleared after being set.
17
TIMER1
RO
0x0
Timer 1 Reset Control
When this bit is set, General-Purpose Timer module 1 is reset. All internal
data is lost and the registers are returned to their reset states. This bit
must be manually cleared after being set.
16
TIMER0
RO
0x0
Timer 0 Reset Control
When this bit is set, General-Purpose Timer module 0 is reset. All internal
data is lost and the registers are returned to their reset states. This bit
must be manually cleared after being set.
15
reserved
RO
0
14
I2C1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2C1 Reset Control
When this bit is set, I2C module 1 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
13
reserved
RO
0
12
I2C0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2C0 Reset Control
When this bit is set, I2C module 0 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
11:10
reserved
RO
0
9
QEI1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
QEI1 Reset Control
When this bit is set, QEI module 1 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
442
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
8
QEI0
RO
0x0
Description
QEI0 Reset Control
When this bit is set, QEI module 0 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
7:6
reserved
RO
0
5
SSI1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
SSI1 Reset Control
When this bit is set, SSI module 1 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
4
SSI0
RO
0x0
SSI0 Reset Control
When this bit is set, SSI module 0 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
3
reserved
RO
0
2
UART2
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
UART2 Reset Control
When this bit is set, UART module 2 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
1
UART1
RO
0x0
UART1 Reset Control
When this bit is set, UART module 1 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
0
UART0
RO
0x0
UART0 Reset Control
When this bit is set, UART module 0 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
July 17, 2013
443
Texas Instruments-Production Data
System Control
Register 128: Software Reset Control 2 (SRCR2), offset 0x048
This register allows individual modules to be reset. Writes to this register are masked by the bits in
the Device Capabilities 4 (DC4) register.
Important: This register is provided for legacy software support only.
The peripheral-specific Software Reset registers (such as SRDMA) should be used to
reset specific peripherals. A write to this legacy register also writes the corresponding
bit in the peripheral-specific register. Any bits that are changed by writing to this register
can be read back correctly with a read of this register. Software must use the
peripheral-specific registers to support modules that are not present in the legacy
registers. If software uses a peripheral-specific register to write a legacy peripheral
(such as the μDMA), the write causes proper operation, but the value of that bit is not
reflected in this register. If software uses both legacy and peripheral-specific register
accesses, the peripheral-specific registers must be accessed by read-modify-write
operations that affect only peripherals that are not present in the legacy registers. In
this manner, both the peripheral-specific and legacy registers have coherent information.
Software Reset Control 2 (SRCR2)
Base 0x400F.E000
Offset 0x048
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
15
14
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
13
12
11
10
9
UDMA
RO
0
reserved
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:14
reserved
RO
0
13
UDMA
RO
0x0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
GPIOJ
GPIOH
GPIOG
GPIOF
GPIOE
GPIOD
GPIOC
GPIOB
GPIOA
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Micro-DMA Reset Control
When this bit is set, uDMA module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
12:9
reserved
RO
0
8
GPIOJ
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Port J Reset Control
When this bit is set, Port J module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
7
GPIOH
RO
0x0
Port H Reset Control
When this bit is set, Port H module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
444
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
6
GPIOG
RO
0x0
Description
Port G Reset Control
When this bit is set, Port G module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
5
GPIOF
RO
0x0
Port F Reset Control
When this bit is set, Port F module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
4
GPIOE
RO
0x0
Port E Reset Control
When this bit is set, Port E module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
3
GPIOD
RO
0x0
Port D Reset Control
When this bit is set, Port D module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
2
GPIOC
RO
0x0
Port C Reset Control
When this bit is set, Port C module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
1
GPIOB
RO
0x0
Port B Reset Control
When this bit is set, Port B module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
0
GPIOA
RO
0x0
Port A Reset Control
When this bit is set, Port A module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
July 17, 2013
445
Texas Instruments-Production Data
System Control
Register 129: Run Mode Clock Gating Control Register 0 (RCGC0), offset
0x100
This register controls the clock gating logic in normal Run mode. Each bit controls a clock enable
for a given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC0 is the clock configuration register for
running operation, SCGC0 for Sleep operation, and DCGC0 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes. Note that there must be a delay of 3 system clocks after a module clock is enabled before
any registers in that module are accessed.
Important: This register is provided for legacy software support only.
The peripheral-specific Run Mode Clock Gating Control registers (such as RCGCWD)
should be used to reset specific peripherals. A write to this legacy register also writes
the corresponding bit in the peripheral-specific register. Any bits that are changed by
writing to this register can be read back correctly with a read of this register. Software
must use the peripheral-specific registers to support modules that are not present in
the legacy registers. If software uses a peripheral-specific register to write a legacy
peripheral (such as Watchdog 1), the write causes proper operation, but the value of
that bit is not reflected in this register. If software uses both legacy and peripheral-specific
register accesses, the peripheral-specific registers must be accessed by
read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Likewise, the ADC Peripheral Configuration (ADCPC) register should be used to
configure the ADC sample rate. However, to support legacy software, the MAXADCnSPD
fields are available. A write to these legacy fields also writes the corresponding field in
the peripheral-specific register. If a field is changed by writing to this register, it can be
read back correctly with a read of this register. Software must use the peripheral-specific
registers to support rates that are not available in this register. If software uses a
peripheral-specific register to set the ADC rate, the write causes proper operation, but
the value of that field is not reflected in this register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
446
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Run Mode Clock Gating Control Register 0 (RCGC0)
Base 0x400F.E000
Offset 0x100
Type RO, reset 0x0000.0040
31
30
29
reserved
Type
Reset
28
WDT1
26
24
23
22
21
19
16
CAN1
CAN0
ADC1
ADC0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
reserved
HIB
RO
0
RO
0
RO
0
RO
1
MAXADC0SPD
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:29
reserved
RO
0
28
WDT1
RO
0x0
RO
0
reserved
RO
0
RO
0
reserved
17
RO
0
MAXADC1SPD
PWM0
18
RO
0
RO
0
reserved
20
RO
0
RO
0
reserved
25
RO
0
reserved
Type
Reset
27
WDT0
RO
0
reserved
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
WDT1 Clock Gating Control
This bit controls the clock gating for the Watchdog Timer module 1. If
set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
27:26
reserved
RO
0
25
CAN1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
CAN1 Clock Gating Control
This bit controls the clock gating for CAN module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
24
CAN0
RO
0x0
CAN0 Clock Gating Control
This bit controls the clock gating for CAN module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
23:21
reserved
RO
0
20
PWM0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PWM Clock Gating Control
This bit controls the clock gating for the PWM module. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
19:18
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
447
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
17
ADC1
RO
0x0
Description
ADC1 Clock Gating Control
This bit controls the clock gating for SAR ADC module 1. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
16
ADC0
RO
0x0
ADC0 Clock Gating Control
This bit controls the clock gating for ADC module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
15:12
reserved
RO
0
11:10
MAXADC1SPD
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
ADC1 Sample Speed
This field sets the rate at which ADC module 1 samples data. You cannot
set the rate higher than the maximum rate. You can set the sample rate
by setting the MAXADC1SPD bit as follows (all other encodings are
reserved):
Value Description
9:8
MAXADC0SPD
RO
0x0
0x3
1M samples/second
0x2
500K samples/second
0x1
250K samples/second
0x0
125K samples/second
ADC0 Sample Speed
This field sets the rate at which ADC0 samples data. You cannot set
the rate higher than the maximum rate. You can set the sample rate by
setting the MAXADC0SPD bit as follows (all other encodings are reserved):
Value Description
7
reserved
RO
0
6
HIB
RO
0x1
0x3
1M samples/second
0x2
500K samples/second
0x1
250K samples/second
0x0
125K samples/second
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
HIB Clock Gating Control
This bit controls the clock gating for the Hibernation module. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
5:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
448
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
3
WDT0
RO
0x0
Description
WDT0 Clock Gating Control
This bit controls the clock gating for the Watchdog Timer module 0. If
set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
2:0
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
449
Texas Instruments-Production Data
System Control
Register 130: Run Mode Clock Gating Control Register 1 (RCGC1), offset
0x104
This register controls the clock gating logic in normal Run mode. Each bit controls a clock enable
for a given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC1 is the clock configuration register for
running operation, SCGC1 for Sleep operation, and DCGC1 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes. Note that there must be a delay of 3 system clocks after a module clock is enabled before
any registers in that module are accessed.
Important: This register is provided for legacy software support only.
The peripheral-specific Run Mode Clock Gating Control registers (such as RCGCTIMER)
should be used to reset specific peripherals. A write to this legacy register also writes
the corresponding bit in the peripheral-specific register. Any bits that are changed by
writing to this register can be read back correctly with a read of this register. Software
must use the peripheral-specific registers to support modules that are not present in
the legacy registers. If software uses a peripheral-specific register to write a legacy
peripheral (such as Timer 0), the write causes proper operation, but the value of that
bit is not reflected in this register. If software uses both legacy and peripheral-specific
register accesses, the peripheral-specific registers must be accessed by
read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Run Mode Clock Gating Control Register 1 (RCGC1)
Base 0x400F.E000
Offset 0x104
Type RO, reset 0x0000.0000
31
30
RO
0
RO
0
15
29
28
27
RO
0
RO
0
RO
0
14
13
12
11
reserved
I2C1
reserved
I2C0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
Type
Reset
26
25
24
COMP2
COMP1
COMP0
RO
0
RO
0
10
reserved
RO
0
RO
0
23
22
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
QEI1
QEI0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:27
reserved
RO
0
21
20
19
18
17
16
TIMER3
TIMER2
TIMER1
TIMER0
RO
0
RO
0
RO
0
RO
0
4
3
2
1
0
SSI1
SSI0
reserved
UART2
UART1
UART0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
reserved
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
450
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
26
COMP2
RO
0x0
Description
Analog Comparator 2 Clock Gating
This bit controls the clock gating for analog comparator 2. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
25
COMP1
RO
0x0
Analog Comparator 1 Clock Gating
This bit controls the clock gating for analog comparator 1. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
24
COMP0
RO
0x0
Analog Comparator 0 Clock Gating
This bit controls the clock gating for analog comparator 0. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
23:20
reserved
RO
0
19
TIMER3
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Timer 3 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 3.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
18
TIMER2
RO
0x0
Timer 2 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 2.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
17
TIMER1
RO
0x0
Timer 1 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 1.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
16
TIMER0
RO
0x0
Timer 0 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 0.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
15
reserved
RO
0
14
I2C1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2C1 Clock Gating Control
This bit controls the clock gating for I2C module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
July 17, 2013
451
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
13
reserved
RO
0
12
I2C0
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2C0 Clock Gating Control
This bit controls the clock gating for I2C module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
11:10
reserved
RO
0
9
QEI1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
QEI1 Clock Gating Control
This bit controls the clock gating for QEI module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
8
QEI0
RO
0x0
QEI0 Clock Gating Control
This bit controls the clock gating for QEI module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
7:6
reserved
RO
0
5
SSI1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
SSI1 Clock Gating Control
This bit controls the clock gating for SSI module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
4
SSI0
RO
0x0
SSI0 Clock Gating Control
This bit controls the clock gating for SSI module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
3
reserved
RO
0
2
UART2
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
UART2 Clock Gating Control
This bit controls the clock gating for UART module 2. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
1
UART1
RO
0x0
UART1 Clock Gating Control
This bit controls the clock gating for UART module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
452
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
0
UART0
RO
0x0
Description
UART0 Clock Gating Control
This bit controls the clock gating for UART module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
July 17, 2013
453
Texas Instruments-Production Data
System Control
Register 131: Run Mode Clock Gating Control Register 2 (RCGC2), offset
0x108
This register controls the clock gating logic in normal Run mode. Each bit controls a clock enable
for a given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC2 is the clock configuration register for
running operation, SCGC2 for Sleep operation, and DCGC2 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes. Note that there must be a delay of 3 system clocks after a module clock is enabled before
any registers in that module are accessed.
Important: This register is provided for legacy software support only.
The peripheral-specific Run Mode Clock Gating Control registers (such as RCGCDMA)
should be used to reset specific peripherals. A write to this legacy register also writes
the corresponding bit in the peripheral-specific register. Any bits that are changed by
writing to this register can be read back correctly with a read of this register. Software
must use the peripheral-specific registers to support modules that are not present in
the legacy registers. If software uses a peripheral-specific register to write a legacy
peripheral (such as the μDMA), the write causes proper operation, but the value of that
bit is not reflected in this register. If software uses both legacy and peripheral-specific
register accesses, the peripheral-specific registers must be accessed by
read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Run Mode Clock Gating Control Register 2 (RCGC2)
Base 0x400F.E000
Offset 0x108
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
GPIOJ
GPIOH
GPIOG
GPIOF
GPIOE
GPIOD
GPIOC
GPIOB
GPIOA
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
RO
0
UDMA
RO
0
reserved
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:14
reserved
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
454
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
13
UDMA
RO
0x0
Description
Micro-DMA Clock Gating Control
This bit controls the clock gating for micro-DMA. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
12:9
reserved
RO
0
8
GPIOJ
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Port J Clock Gating Control
This bit controls the clock gating for Port J. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
7
GPIOH
RO
0x0
Port H Clock Gating Control
This bit controls the clock gating for Port H. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
6
GPIOG
RO
0x0
Port G Clock Gating Control
This bit controls the clock gating for Port G. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
5
GPIOF
RO
0x0
Port F Clock Gating Control
This bit controls the clock gating for Port F. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
4
GPIOE
RO
0x0
Port E Clock Gating Control
Port E Clock Gating Control. This bit controls the clock gating for Port
E. If set, the module receives a clock and functions. Otherwise, the
module is unclocked and disabled. If the module is unclocked, a read
or write to the module generates a bus fault.
3
GPIOD
RO
0x0
Port D Clock Gating Control
Port D Clock Gating Control. This bit controls the clock gating for Port
D. If set, the module receives a clock and functions. Otherwise, the
module is unclocked and disabled. If the module is unclocked, a read
or write to the module generates a bus fault.
2
GPIOC
RO
0x0
Port C Clock Gating Control
This bit controls the clock gating for Port C. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
1
GPIOB
RO
0x0
Port B Clock Gating Control
This bit controls the clock gating for Port B. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
July 17, 2013
455
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
0
GPIOA
RO
0x0
Description
Port A Clock Gating Control
This bit controls the clock gating for Port A. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
456
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 132: Sleep Mode Clock Gating Control Register 0 (SCGC0), offset
0x110
This register controls the clock gating logic in Sleep mode. Each bit controls a clock enable for a
given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC0 is the clock configuration register for
running operation, SCGC0 for Sleep operation, and DCGC0 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes.
Important: This register is provided for legacy software support only.
The peripheral-specific Sleep Mode Clock Gating Control registers (such as SCGCWD)
should be used to reset specific peripherals. A write to this legacy register also writes
the corresponding bit in the peripheral-specific register. Any bits that are changed by
writing to this register can be read back correctly with a read of this register. Software
must use the peripheral-specific registers to support modules that are not present in
the legacy registers. If software uses a peripheral-specific register to write a legacy
peripheral (such as Watchdog 1), the write causes proper operation, but the value of
that bit is not reflected in this register. If software uses both legacy and peripheral-specific
register accesses, the peripheral-specific registers must be accessed by
read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Sleep Mode Clock Gating Control Register 0 (SCGC0)
Base 0x400F.E000
Offset 0x110
Type RO, reset 0x0000.0040
31
30
29
reserved
Type
Reset
28
WDT1
27
26
reserved
25
24
23
21
reserved
20
19
16
CAN1
CAN0
ADC1
ADC0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
HIB
Bit/Field
Name
Type
Reset
31:29
reserved
RO
0
28
WDT1
RO
0x0
RO
1
reserved
RO
0
RO
0
reserved
17
RO
0
RO
0
PWM0
18
RO
0
reserved
Type
Reset
22
WDT0
RO
0
reserved
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
WDT1 Clock Gating Control
This bit controls the clock gating for Watchdog Timer module 1. If set,
the module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
July 17, 2013
457
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
27:26
reserved
RO
0
25
CAN1
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
CAN1 Clock Gating Control
This bit controls the clock gating for CAN module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
24
CAN0
RO
0x0
CAN0 Clock Gating Control
This bit controls the clock gating for CAN module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
23:21
reserved
RO
0
20
PWM0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PWM Clock Gating Control
This bit controls the clock gating for the PWM module. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
19:18
reserved
RO
0
17
ADC1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
ADC1 Clock Gating Control
This bit controls the clock gating for ADC module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
16
ADC0
RO
0x0
ADC0 Clock Gating Control
This bit controls the clock gating for ADC module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
15:7
reserved
RO
0
6
HIB
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
HIB Clock Gating Control
This bit controls the clock gating for the Hibernation module. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
5:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
458
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
3
WDT0
RO
0x0
Description
WDT0 Clock Gating Control
This bit controls the clock gating for the Watchdog Timer module 0. If
set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
2:0
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
459
Texas Instruments-Production Data
System Control
Register 133: Sleep Mode Clock Gating Control Register 1 (SCGC1), offset
0x114
This register controls the clock gating logic in Sleep mode. Each bit controls a clock enable for a
given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC1 is the clock configuration register for
running operation, SCGC1 for Sleep operation, and DCGC1 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes.
Important: This register is provided for legacy software support only.
The peripheral-specific Sleep Mode Clock Gating Control registers (such as
SCGCTIMER) should be used to reset specific peripherals. A write to this legacy register
also writes the corresponding bit in the peripheral-specific register. Any bits that are
changed by writing to this register can be read back correctly with a read of this register.
Software must use the peripheral-specific registers to support modules that are not
present in the legacy registers. If software uses a peripheral-specific register to write a
legacy peripheral (such as Timer 0), the write causes proper operation, but the value
of that bit is not reflected in this register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Sleep Mode Clock Gating Control Register 1 (SCGC1)
Base 0x400F.E000
Offset 0x114
Type RO, reset 0x0000.0000
31
30
RO
0
RO
0
15
29
28
27
RO
0
RO
0
RO
0
14
13
12
11
reserved
I2C1
reserved
I2C0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
Type
Reset
26
25
24
COMP2
COMP1
COMP0
RO
0
RO
0
10
reserved
RO
0
RO
0
23
22
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
QEI1
QEI0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:27
reserved
RO
0
26
COMP2
RO
0x0
21
20
19
18
17
16
TIMER3
TIMER2
TIMER1
TIMER0
RO
0
RO
0
RO
0
RO
0
4
3
2
1
0
SSI1
SSI0
reserved
UART2
UART1
UART0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
reserved
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Analog Comparator 2 Clock Gating
This bit controls the clock gating for analog comparator 2. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
460
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
25
COMP1
RO
0x0
Description
Analog Comparator 1 Clock Gating
This bit controls the clock gating for analog comparator 1. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
24
COMP0
RO
0x0
Analog Comparator 0 Clock Gating
This bit controls the clock gating for analog comparator 0. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
23:20
reserved
RO
0
19
TIMER3
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Timer 3 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 3.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
18
TIMER2
RO
0x0
Timer 2 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 2.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
17
TIMER1
RO
0x0
Timer 1 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 1.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
16
TIMER0
RO
0x0
Timer 0 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 0.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
15
reserved
RO
0
14
I2C1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2C1 Clock Gating Control
This bit controls the clock gating for I2C module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
13
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
461
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
12
I2C0
RO
0x0
Description
I2C0 Clock Gating Control
This bit controls the clock gating for I2C module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
11:10
reserved
RO
0
9
QEI1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
QEI1 Clock Gating Control
This bit controls the clock gating for QEI module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
8
QEI0
RO
0x0
QEI0 Clock Gating Control
This bit controls the clock gating for QEI module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
7:6
reserved
RO
0
5
SSI1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
SSI1 Clock Gating Control
This bit controls the clock gating for SSI module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
4
SSI0
RO
0x0
SSI0 Clock Gating Control
This bit controls the clock gating for SSI module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
3
reserved
RO
0
2
UART2
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
UART2 Clock Gating Control
This bit controls the clock gating for UART module 2. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
1
UART1
RO
0x0
UART1 Clock Gating Control
This bit controls the clock gating for UART module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
462
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
0
UART0
RO
0x0
Description
UART0 Clock Gating Control
This bit controls the clock gating for UART module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
July 17, 2013
463
Texas Instruments-Production Data
System Control
Register 134: Sleep Mode Clock Gating Control Register 2 (SCGC2), offset
0x118
This register controls the clock gating logic in Sleep mode. Each bit controls a clock enable for a
given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC2 is the clock configuration register for
running operation, SCGC2 for Sleep operation, and DCGC2 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes.
Important: This register is provided for legacy software support only.
The peripheral-specific Sleep Mode Clock Gating Control registers (such as SCGCDMA)
should be used to reset specific peripherals. A write to this legacy register also writes
the corresponding bit in the peripheral-specific register. Any bits that are changed by
writing to this register can be read back correctly with a read of this register. Software
must use the peripheral-specific registers to support modules that are not present in
the legacy registers. If software uses a peripheral-specific register to write a legacy
peripheral (such as the μDMA), the write causes proper operation, but the value of that
bit is not reflected in this register. If software uses both legacy and peripheral-specific
register accesses, the peripheral-specific registers must be accessed by
read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Sleep Mode Clock Gating Control Register 2 (SCGC2)
Base 0x400F.E000
Offset 0x118
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
GPIOJ
GPIOH
GPIOG
GPIOF
GPIOE
GPIOD
GPIOC
GPIOB
GPIOA
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
RO
0
UDMA
RO
0
reserved
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:14
reserved
RO
0
13
UDMA
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Micro-DMA Clock Gating Control
This bit controls the clock gating for micro-DMA. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
464
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
12:9
reserved
RO
0
8
GPIOJ
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Port J Clock Gating Control
This bit controls the clock gating for Port J. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
7
GPIOH
RO
0x0
Port H Clock Gating Control
This bit controls the clock gating for Port H. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
6
GPIOG
RO
0x0
Port G Clock Gating Control
This bit controls the clock gating for Port G. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
5
GPIOF
RO
0x0
Port F Clock Gating Control
This bit controls the clock gating for Port F. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
4
GPIOE
RO
0x0
Port E Clock Gating Control
Port E Clock Gating Control. This bit controls the clock gating for Port
E. If set, the module receives a clock and functions. Otherwise, the
module is unclocked and disabled. If the module is unclocked, a read
or write to the module generates a bus fault.
3
GPIOD
RO
0x0
Port D Clock Gating Control
Port D Clock Gating Control. This bit controls the clock gating for Port
D. If set, the module receives a clock and functions. Otherwise, the
module is unclocked and disabled. If the module is unclocked, a read
or write to the module generates a bus fault.
2
GPIOC
RO
0x0
Port C Clock Gating Control
This bit controls the clock gating for Port C. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
1
GPIOB
RO
0x0
Port B Clock Gating Control
This bit controls the clock gating for Port B. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
0
GPIOA
RO
0x0
Port A Clock Gating Control
This bit controls the clock gating for Port A. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
July 17, 2013
465
Texas Instruments-Production Data
System Control
Register 135: Deep Sleep Mode Clock Gating Control Register 0 (DCGC0),
offset 0x120
This register controls the clock gating logic in Deep-Sleep mode. Each bit controls a clock enable
for a given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC0 is the clock configuration register for
running operation, SCGC0 for Sleep operation, and DCGC0 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes.
Important: This register is provided for legacy software support only.
The peripheral-specific Deep Sleep Mode Clock Gating Control registers (such as
DCGCWD) should be used to reset specific peripherals. A write to this legacy register
also writes the corresponding bit in the peripheral-specific register. Any bits that are
changed by writing to this register can be read back correctly with a read of this register.
Software must use the peripheral-specific registers to support modules that are not
present in the legacy registers. If software uses a peripheral-specific register to write a
legacy peripheral (such as Watchdog 1), the write causes proper operation, but the
value of that bit is not reflected in this register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Deep Sleep Mode Clock Gating Control Register 0 (DCGC0)
Base 0x400F.E000
Offset 0x120
Type RO, reset 0x0000.0040
31
30
29
reserved
Type
Reset
28
WDT1
27
26
reserved
25
24
23
21
reserved
20
19
16
CAN1
CAN0
ADC1
ADC0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
HIB
Bit/Field
Name
Type
Reset
31:29
reserved
RO
0
28
WDT1
RO
0x0
RO
1
reserved
RO
0
RO
0
reserved
17
RO
0
RO
0
PWM0
18
RO
0
reserved
Type
Reset
22
WDT0
RO
0
reserved
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
WDT1 Clock Gating Control
This bit controls the clock gating for the Watchdog Timer module 1. If
set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
466
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
27:26
reserved
RO
0
25
CAN1
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
CAN1 Clock Gating Control
This bit controls the clock gating for CAN module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
24
CAN0
RO
0x0
CAN0 Clock Gating Control
This bit controls the clock gating for CAN module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
23:21
reserved
RO
0
20
PWM0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PWM Clock Gating Control
This bit controls the clock gating for the PWM module. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
19:18
reserved
RO
0
17
ADC1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
ADC1 Clock Gating Control
This bit controls the clock gating for ADC module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
16
ADC0
RO
0x0
ADC0 Clock Gating Control
This bit controls the clock gating for ADC module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
15:7
reserved
RO
0
6
HIB
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
HIB Clock Gating Control
This bit controls the clock gating for the Hibernation module. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
5:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
July 17, 2013
467
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
3
WDT0
RO
0x0
Description
WDT0 Clock Gating Control
This bit controls the clock gating for the Watchdog Timer module 0. If
set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
2:0
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
468
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 136: Deep-Sleep Mode Clock Gating Control Register 1 (DCGC1),
offset 0x124
This register controls the clock gating logic in Deep-Sleep mode. Each bit controls a clock enable
for a given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC1 is the clock configuration register for
running operation, SCGC1 for Sleep operation, and DCGC1 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes.
Important: This register is provided for legacy software support only.
The peripheral-specific Deep Sleep Mode Clock Gating Control registers (such as
DCGCTIMER) should be used to reset specific peripherals. A write to this legacy register
also writes the corresponding bit in the peripheral-specific register. Any bits that are
changed by writing to this register can be read back correctly with a read of this register.
Software must use the peripheral-specific registers to support modules that are not
present in the legacy registers. If software uses a peripheral-specific register to write a
legacy peripheral (such as Timer 0), the write causes proper operation, but the value
of that bit is not reflected in this register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Deep-Sleep Mode Clock Gating Control Register 1 (DCGC1)
Base 0x400F.E000
Offset 0x124
Type RO, reset 0x0000.0000
31
30
RO
0
RO
0
15
29
28
27
RO
0
RO
0
RO
0
14
13
12
11
reserved
I2C1
reserved
I2C0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
Type
Reset
26
25
24
COMP2
COMP1
COMP0
RO
0
RO
0
10
reserved
RO
0
RO
0
23
22
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
QEI1
QEI0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:27
reserved
RO
0
26
COMP2
RO
0x0
21
20
19
18
17
16
TIMER3
TIMER2
TIMER1
TIMER0
RO
0
RO
0
RO
0
RO
0
4
3
2
1
0
SSI1
SSI0
reserved
UART2
UART1
UART0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
reserved
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Analog Comparator 2 Clock Gating
This bit controls the clock gating for analog comparator 2. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
July 17, 2013
469
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
25
COMP1
RO
0x0
Description
Analog Comparator 1 Clock Gating
This bit controls the clock gating for analog comparator 1. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
24
COMP0
RO
0x0
Analog Comparator 0 Clock Gating
This bit controls the clock gating for analog comparator 0. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
23:20
reserved
RO
0
19
TIMER3
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Timer 3 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 3.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
18
TIMER2
RO
0x0
Timer 2 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 2.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
17
TIMER1
RO
0x0
Timer 1 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 1.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
16
TIMER0
RO
0x0
Timer 0 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 0.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
15
reserved
RO
0
14
I2C1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2C1 Clock Gating Control
This bit controls the clock gating for I2C module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
13
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
470
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Bit/Field
Name
Type
Reset
12
I2C0
RO
0x0
Description
I2C0 Clock Gating Control
This bit controls the clock gating for I2C module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
11:10
reserved
RO
0
9
QEI1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
QEI1 Clock Gating Control
This bit controls the clock gating for QEI module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
8
QEI0
RO
0x0
QEI0 Clock Gating Control
This bit controls the clock gating for QEI module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
7:6
reserved
RO
0
5
SSI1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
SSI1 Clock Gating Control
This bit controls the clock gating for SSI module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
4
SSI0
RO
0x0
SSI0 Clock Gating Control
This bit controls the clock gating for SSI module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
3
reserved
RO
0
2
UART2
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
UART2 Clock Gating Control
This bit controls the clock gating for UART module 2. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
1
UART1
RO
0x0
UART1 Clock Gating Control
This bit controls the clock gating for UART module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
July 17, 2013
471
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
0
UART0
RO
0x0
Description
UART0 Clock Gating Control
This bit controls the clock gating for UART module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
472
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 137: Deep Sleep Mode Clock Gating Control Register 2 (DCGC2),
offset 0x128
This register controls the clock gating logic in Deep-Sleep mode. Each bit controls a clock enable
for a given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC2 is the clock configuration register for
running operation, SCGC2 for Sleep operation, and DCGC2 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes.
Important: This register is provided for legacy software support only.
The peripheral-specific Deep Sleep Mode Clock Gating Control registers (such as
DCGCDMA) should be used to reset specific peripherals. A write to this legacy register
also writes the corresponding bit in the peripheral-specific register. Any bits that are
changed by writing to this register can be read back correctly with a read of this register.
Software must use the peripheral-specific registers to support modules that are not
present in the legacy registers. If software uses a peripheral-specific register to write a
legacy peripheral (such as the μDMA), the write causes proper operation, but the value
of that bit is not reflected in this register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Deep Sleep Mode Clock Gating Control Register 2 (DCGC2)
Base 0x400F.E000
Offset 0x128
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
GPIOJ
GPIOH
GPIOG
GPIOF
GPIOE
GPIOD
GPIOC
GPIOB
GPIOA
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
RO
0
UDMA
RO
0
reserved
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:14
reserved
RO
0
13
UDMA
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Micro-DMA Clock Gating Control
This bit controls the clock gating for micro-DMA. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
July 17, 2013
473
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
12:9
reserved
RO
0
8
GPIOJ
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Port J Clock Gating Control
This bit controls the clock gating for Port J. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
7
GPIOH
RO
0x0
Port H Clock Gating Control
This bit controls the clock gating for Port H. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
6
GPIOG
RO
0x0
Port G Clock Gating Control
This bit controls the clock gating for Port G. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
5
GPIOF
RO
0x0
Port F Clock Gating Control
This bit controls the clock gating for Port F. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
4
GPIOE
RO
0x0
Port E Clock Gating Control
Port E Clock Gating Control. This bit controls the clock gating for Port
E. If set, the module receives a clock and functions. Otherwise, the
module is unclocked and disabled. If the module is unclocked, a read
or write to the module generates a bus fault.
3
GPIOD
RO
0x0
Port D Clock Gating Control
Port D Clock Gating Control. This bit controls the clock gating for Port
D. If set, the module receives a clock and functions. Otherwise, the
module is unclocked and disabled. If the module is unclocked, a read
or write to the module generates a bus fault.
2
GPIOC
RO
0x0
Port C Clock Gating Control
This bit controls the clock gating for Port C. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
1
GPIOB
RO
0x0
Port B Clock Gating Control
This bit controls the clock gating for Port B. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
0
GPIOA
RO
0x0
Port A Clock Gating Control
This bit controls the clock gating for Port A. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
474
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 138: Device Capabilities 9 (DC9), offset 0x190
This register is predefined by the part and can be used to verify ADC digital comparator features.
Important: This register is provided for legacy software support only.
The ADC Peripheral Properties (ADCPP) register should be used to determine how
many digital comparators are available on the ADC module. A read of this register
correctly identifies if legacy comparators are present. Software must use the ADCPP
register to determine if a comparator that is not supported by the DCn registers is
present.
Device Capabilities 9 (DC9)
Base 0x400F.E000
Offset 0x190
Type RO, reset 0x00FF.00FF
31
30
29
28
27
26
25
24
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
ADC1DC7 ADC1DC6 ADC1DC5 ADC1DC4 ADC1DC3 ADC1DC2 ADC1DC1 ADC1DC0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
7
6
5
4
3
2
1
0
ADC0DC7 ADC0DC6 ADC0DC5 ADC0DC4 ADC0DC3 ADC0DC2 ADC0DC1 ADC0DC0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:24
reserved
RO
0
23
ADC1DC7
RO
0x1
RO
0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
ADC1 DC7 Present
When set, indicates that ADC module 1 Digital Comparator 7 is present.
22
ADC1DC6
RO
0x1
ADC1 DC6 Present
When set, indicates that ADC module 1 Digital Comparator 6 is present.
21
ADC1DC5
RO
0x1
ADC1 DC5 Present
When set, indicates that ADC module 1 Digital Comparator 5 is present.
20
ADC1DC4
RO
0x1
ADC1 DC4 Present
When set, indicates that ADC module 1 Digital Comparator 4 is present.
19
ADC1DC3
RO
0x1
ADC1 DC3 Present
When set, indicates that ADC module 1 Digital Comparator 3 is present.
18
ADC1DC2
RO
0x1
ADC1 DC2 Present
When set, indicates that ADC module 1 Digital Comparator 2 is present.
17
ADC1DC1
RO
0x1
ADC1 DC1 Present
When set, indicates that ADC module 1 Digital Comparator 1 is present.
16
ADC1DC0
RO
0x1
ADC1 DC0 Present
When set, indicates that ADC module 1 Digital Comparator 0 is present.
July 17, 2013
475
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
15:8
reserved
RO
0
7
ADC0DC7
RO
0x1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
ADC0 DC7 Present
When set, indicates that ADC module 0 Digital Comparator 7 is present.
6
ADC0DC6
RO
0x1
ADC0 DC6 Present
When set, indicates that ADC module 0 Digital Comparator 6 is present.
5
ADC0DC5
RO
0x1
ADC0 DC5 Present
When set, indicates that ADC module 0 Digital Comparator 5 is present.
4
ADC0DC4
RO
0x1
ADC0 DC4 Present
When set, indicates that ADC module 0 Digital Comparator 4 is present.
3
ADC0DC3
RO
0x1
ADC0 DC3 Present
When set, indicates that ADC module 0 Digital Comparator 3 is present.
2
ADC0DC2
RO
0x1
ADC0 DC2 Present
When set, indicates that ADC module 0 Digital Comparator 2 is present.
1
ADC0DC1
RO
0x1
ADC0 DC1 Present
When set, indicates that ADC module 0 Digital Comparator 1 is present.
0
ADC0DC0
RO
0x1
ADC0 DC0 Present
When set, indicates that ADC module 0 Digital Comparator 0 is present.
476
July 17, 2013
Texas Instruments-Production Data
Tiva™ TM4C123BE6PZ Microcontroller (identical to LM4F212E5QC)
Register 139: Non-Volatile Memory Information (NVMSTAT), offset 0x1A0
This register is predefined by the part and can be used to verify features.
Important: This register is provided for legacy software support only.
The ROM Third-Party Software (ROMSWMAP) register should be used to determine
the presence of third-party software in the on-chip ROM on this microcontroller. A read
of the TPSW bit in this register correctly identifies the presence of legacy third-party
software. Software should use the ROMSWMAP register for software that is not on
legacy devices.
Non-Volatile Memory Information (NVMSTAT)
Base 0x400F.E000
Offset 0x1A0
Type RO, reset 0x0000.0001
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0
0
FWB
RO
0x1
RO
0
0
FWB
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
32 Word Flash Write Buffer Available
When set, indicates that the 32 word Flash memory write buffer feature
is available.
July 17, 2013
477
Texas Instruments-Production Data
System Exception Module
6
System Exception Module
This module is an AHB peripheral that handles system-level Cortex-M4 FPU exceptions. For functions
with registers mapped into this aperture, if the function is not available on a device, then all writes
to the associated registers are ignored and reads return zeros.
6.1
Functional Description
The System Exception module provides control and status of the system-level interrupts. All the
interrupt events are ORed together before being sent to the interrupt controller, so the System
Exception module can only generate a single interrupt request to the controller at any given time.
Software can service multiple interrupt events in a single interrupt service routine by reading the
System Exception Masked Interrupt Status (SYSEXCMIS) register. The interrupt events that can
trigger a controller-level interrupt are defined in the System Exception Interrupt Mask (SYSEXCIM)
register by setting the corresponding interrupt mask bits. If interrupts are not used, 
Similar pages