CRYSTEK CCPD-575 5ã 7.5mm smd ultra-low phase noise lvpecl clock oscillator Datasheet

CCPD-575 Model
5×7.5 mm SMD, 3.3V, LVPECL
CCPD-575 5×7.5mm SMD
Ultra-Low Phase Noise
LVPECL Clock Oscillator
Model CCPD-575 has an industry leading phase noise for an
LVPECL oscillator. The noise floor is typically @ -162 dBc/Hz!
This is at least 15 dB lower phase noise than most LVPECL
oscillators on the market today. Close-in phase noise is also
excellent @ -90 dBc/Hz for the 100 MHz variant.
This overall ultra-low phase noise translates to a typical phase
jitter of 65 fs RMS (12 kHz to 20 MHz) at 156.250 MHz.
5×7.5mm SMD
Applications:
Digital Video
SONET/SDH/DWDM
Storage Area Networks
Broadband Access
Ethernet, Gigabit Ethernet
Rev: S
Date: 18-Jan-2017
Page 1 of 4
C
CRYSTEK
CORPORATION
12730 Commonwealth Drive • Fort Myers, Florida 33913
Phone: 239-561-3311 • 800-237-3061
Fax: 239-561-1025 • www.crystek.com
CCPD-575 Model
5×7.5 mm SMD, 3.3V, LVPECL
CCPD-575 5×7.5mm SMD
Ultra-Low Phase Noise
LVPECL Clock Oscillator
Frequency Range:
50.000 MHz to 156.250 MHz*
*Standard Frequencies
Frequency Stability Options:
±20ppm, ±25ppm, ±50ppm
(MHz)
Operating Temperature Range:
-40°C to +85°C
80.000
100.000
-45°C to 90°C
Storage Temperature Range:
122.880
3.3V ± 0.3V
Input Voltage:
125.000
156.250
Input Current:
80mA Typical, 88mA Max
Output:
Differential LVPECL
40/60% Max @ zero crossing point
Symmetry:
Rise/Fall Time:
300 ps Max (20% to 80%)
Logic Terminated to Vdd-2V into 50 Ω:
“0”=1.37 Min, 1.74 Max
Output Low Voltage:
“1”=2.05 Min, 2.54 Max
Output High Voltage:
200 ns Max
Disable Time:
200 ms Max
Enable Time:
65 fs RMS Typical @ 156.250 MHz
Phase Jitter: 12kHz~20MHz
Phase Noise: (See Plot Below)
None
Sub-harmonics:
<3ppm 1st year, <1ppm every year thereafter
Aging:
Part Number Example: CCPD-575X-20-100.000 3.3V, -40/85°C, ±20ppm, 100.000 MHz
100.000 MHz LVPECL 3.3V
Rev: S
Date: 18-Jan-2017
Page 2 of 4
Specifications subject to change without notice.
C
CRYSTEK
CORPORATION
12730 Commonwealth Drive • Fort Myers, Florida 33913
Phone: 239-561-3311 • 800-237-3061
Fax: 239-561-1025 • www.crystek.com
CCPD-575 Model
5×7.5 mm SMD, 3.3V, LVPECL
CCPD-575 5×7.5mm SMD
Ultra-Low Phase Noise
LVPECL Clock Oscillator
122.880 MHz LVPECL 3.3V
156.250 MHz LVPECL 3.3V
Rev: S
Date: 18-Jan-2017
Page 3 of 4
C
CRYSTEK
CORPORATION
12730 Commonwealth Drive • Fort Myers, Florida 33913
Phone: 239-561-3311 • 800-237-3061
Fax: 239-561-1025 • www.crystek.com
CCPD-575 5×7.5mm SMD
Ultra-Low Phase Noise
LVPECL Clock Oscillator
CCPD-575 Model
5×7.5 mm SMD, 3.3V, LVPECL
Mechanical:
Shock:
Solderability:
Vibration:
Solvent Resistance:
Resistance to Soldering Heat:
Environmental:
Thermal Shock:
Moisture Resistance:
MIL-STD-883, Method 2002, Condition B
MIL-STD-883, Method 2003
MIL-STD-883, Method 2007, Condition A
MIL-STD-202, Method 215
MIL-STD-202, Method 210, Condition I or J
MIL-STD-883, Method 1011, Condition A
MIL-STD-883, Method 1004
RECOMMENDED REFLOW SOLDERING PROFILE
Ramp-Up
3°C/Sec Max.
Critical Temperature
Zone
TEMPERATURE
260°C
Ramp-Down
6°C/Sec.
217°C
200°C
150°C
Preheat
180 Secs. Max.
90 Secs. Max.
8 Minutes Max.
260°C for
10 Secs. Max.
NOTE: Reflow Profile with 240°C peak also acceptable.
0.295 -0.008 +0.035
(7.50 -0.20 +0.89)
CCPD-575X-TT
Freq
YYWW XX
TT=Tolerance
Dimensions inches (mm)
All dimensions are Max unless otherwise specified.
0.200 ±0.015
(5.08 ±0.38)
Denotes pad 1
YYWW=Date Code
XX=Lot Code
0.099
(2.50)
0.050
(1.27)
0.01µF
6
0.058
(1.47)
#1
#2
#3
#6
#5
#4
C
5
4
0.046
(1.16)
0.100
(2.54)
0.200
(5.08)
CRYSTEK
CORPORATION
Function pin 1
Output pin
Open or N/C
"1" level 2.0V Min
"0" level 0.8V Max
Active
Active
High Z
SUGGESTED PAD LAYOUT
via to
ground
0.046
(1.16)
Enable/Disable
0.154
(3.91)
0.071
(1.80)
1
2
0.100
(2.54)
0.200
(5.08)
3
PIN
Connection
1
2
3
4
5
6
Enable/Disable
N/C
GND
Output
Comp Output
Vcc
Rev: S
Date: 18-Jan-2017
Page 4 of 4
12730 Commonwealth Drive • Fort Myers, Florida 33913
Phone: 239-561-3311 • 800-237-3061
Fax: 239-561-1025 • www.crystek.com
Similar pages