MPD MPM-02SV-09 Ultra wide input, 2w miniature, board mount ac/dc power supply Datasheet

MPM-02V Series
Ultra Wide Input, 2W
Miniature, Board Mount
AC/DC Power Supplies
Electrical Specifications
Key Features:
Specifications typical @ +25°C, 230 VAC input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
• 2W Output Power
Parameter
• Universal 85-305 VAC Input
Input Voltage Range
• EN 60950 Approved (UL)
• Meets IEC Safety Class II
Input Frequency
Input Current
• -25ºC to +70ºC Operation
Inrush Current
• Single Regulated Output
Conditions
Leakage Current
• >300 kHour MTBF
Output
• Ultra-Miniature DIP Case
Parameter
Output Voltage
Output Current
Output Voltage Accuracy
Line Regulation
Load Regulation
Ripple & Noise (20 MHz)
Hold-Up Time
Temperature Coefficient
Short Circuit Protection
Over Current Protection
Min.
Typ.
85
120
47
See Model Selection Guide
110 VAC
5.0
230 VAC
11.0
110/230 VAC
Max.
305
430
63
Units
VAC
VDC
Hz
0.15
mA
Conditions
Min.
Typ.
See Model Selection Guide
See Model Selection Guide
See Note 1
VIN = Min to Max
See Note 2
100
115 VAC
30
230 VAC
140
±0.02
Continuous (Autorecovery)
>110% With Autorecovery
Max.
Units
±5.0
±2.0
±5.0
200
%
%
%
mV Pk - Pk
A Pk
mSec
%/°C
General
Parameter
Isolation Voltage
Conditions
Input to Output
Conducted
Radiated
Electrostatic Discharge (ESD)
RF Field Susceptibility
Electrical Fast Transients/Bursts On Mains
Surge
CS
PFM
Volt. Dips, Short & Inter. Immunity
EMI/RFI, See Note 3
EMC Compliance
Switching Frequency
Min.
3,000
Typ.
Max.
Units
VAC
CISPR22/EN 55022 Level B
CISPR22/EN 55022 Level B
EN 61000-4-2 Level B 4 kV/8 kV
EN 61000-4-3 Level A 10V/m
EN 61000-4-4 Level B 2 kV
EN 61000-4-5 Level B 1 kV/2 kV
EN 61000-4-6 Level A 10V rms
EN 61000-4-8 Level A 10A/m
EN 61000-4-11 Level B 0 - 70%
100
kHz
Environmental
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Parameter
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Physical
Case Size
Case Material
Weight
Conditions
Min.
Typ.
Max.
-25
+25
+70
-40
+85
Free Air Convection (See Derating Curve)
RH, Non-condensing
90
Ambient
Units
°C
°C
%
1.327 x 0.874 x 0.708 Inches (33.7 x 22.2 x 18.0 mm)
Non-Conductive Black Plastic (UL94-V0)
0.70 Oz (20g)
Reliability Specifications
Parameter
MTBF
Safety Approvals
Safety Class
Conditions
Min.
Typ.
MIL HDBK 217F, 25°C, Gnd Benign
300
UL 60950, EN 60950
IEC 61140 Class II
www.micropowerdirect.com
Max.
Units
kHours
www.micropowerdirect.com
Model Selection Guide
Input
Model
Number
MPM-02SV-03
MPM-02SV-05
MPM-02SV-09
MPM-02SV-12
MPM-02SV-15
MPM-02SV-24
Output
Voltage
Current
Standby
Power
115 VAC
230 VAC
(VDC)
(mA)
(W Typ)
(µF, Max)
44
44
44
44
44
44
25
25
25
25
25
25
3.3
5.0
9.0
12.0
15.0
24.0
600
400
222
167
133
83
0.1
0.1
0.1
0.1
0.1
0.1
4,000
4,000
2,200
2,200
1,000
680
Current (mA)
Capacitive
Load
Efficiency
(%, Typ)
65
70
72
76
76
78
N
Notes:
1. Output voltage accuracy for 3.3V output models is
±6% Max.
2. Load regulation is measured for an output change of
10% to 100% at nominal input line.
3. The MPM-02V meets EN 55022 Class B without
external components. For applications where noise
sensitivity is critical, a recommended circuit is given
below.
4. It is recommended that a fuse be used on the input
of a power supply for protection. For the MPM-02V
series, a 0.5A/250 VAC slow blow should be used.
Typical Connection
The diagram above illustrates a typical application connection of the MPM-02V series. Notes on this
circuit (starting with the input circuit) are:
Mechanical Dimensions
1. To maintain clearance and creepage distances (for Class I & Class II devices) the board layout should
guarantee the following spacing between the L and N inputs (before the fuse):
Clearance - 2 mm
Creepage - 2.5 mm
2. The recommended fuse is a 0.5A/250V slow blow. Additionally, a thermistor (NTC) may be used on
the input line. A 5D-9 is recommended.
3. For EMI sensitive applications, the input filtering circuit (inside the dotted boxes) may be added. The
filter consists of:
Cx: Capacitor C3 is 0.1 µF/300V to 0.33 µF/300V
CY: Capacitors C1 and C2 are 2200 pF/400V
T1: Common mode choke. Inductance is
about 10 mH to 30 mH.
4. The MOV is required for surge protection. Recommended
is a 561KD14.
5. The output filtering capacitor (C5) is a high frequency,
low resistance electrolytic capacitor. A ceramic capacitor
(C4) is used to filter high frequency noise. Recommended
values are given in the table at right.
6. The TVS is recommended to protect application circuitry
in the event of a fault. Recommended values are given in
the table at right.
VOUT
C4
C5
TVS
3.3
5.0
9.0
12.0
15.0
24.0
1 µF/50V
1 µF/50V
1 µF/50V
1 µF/50V
1 µF/50V
1 µF/50V
220 µF
220 µF
120 µF
120 µF
120 µF
68 µF
SMBJ7.0A
SMBJ7.0A
SMBJ12A
SMBJ20A
SMBJ20A
SMBJ30A
Derating Curve
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
Pin Connections
Pin
1
2
3
4
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
Function
AC-Neutral
AC-Line
-Vout
+Vout
E-Mail: [email protected]
Similar pages