Marktech MTG7-001L-XBD00-RD-0701 Cree xb-d color series on board Datasheet

Cree XB-D Color Series on Board
Cree XB-D Color Series
Cree XLamp XB-D color LEDs extend the double lumens-per-dollar performance of
the XB package to color LEDs, delivering up to 40% higher maximum light output
than XP-E color LEDs. The combination of performance and small size of XB-D
color LEDs enable better color mixing and lower system cost.
FEATURES
> Cree's smallest lighting class LED: 2.45 x 2.45 mm
> 1A Maximum Drive Current
> Wide viewing angle: 115°(white) to 140° (red)
> Electrically Neutral Thermal Path
FLUX CHARACTERISTICS @ 85°C
COLOR
Blue
Green
Red-Orange
Red
CHARACTERISTICS
Thermal resistance, junction to solder point - white, royal blue, blue
Thermal resistance, junction to solder point - green
Thermal resistance, junction to solder point - amber
Thermal resistance, junction to solder point - red-orange, red
Viewing angle (FWHM) - white
Viewing angle (FWHM) - royal blue, blue, green
Viewing angle (FWHM) - amber, red-orange, red
Temperature coefficient of voltage - white
Temperature coefficient of voltage - royal blue, blue, green
Temperature coefficient of voltage - amber, red-orange, red
ESD classification (HBM per Mil-Std-883D)
DC forward current
Reverse voltage
Forward voltage (@ 350 mA, 85 °C) - white
Forward voltage (@ 350 mA, 25 °C) - royal blue, blue
Forward voltage (@ 350 mA, 25 °C) - green
Forward voltage (@ 350 mA, 25 °C) - amber, red-orange, red
LED junction temperature
APPLICATIONS
> Non-Directional
> Directional
> Downlight
> Consumer Portable
DWL (nm) MIN.FLUX (LM) @350MA KIT USED
35.2
465-485
0Z01
93.9
520-535
0B01
O901
80.6
610-620
O701
620-630
67.2
UNIT
°C/W
°C/W
°C/W
°C/W
degrees
degrees
degrees
mV/°C
mV/°C
mV/°C
mA
V
V
V
V
V
°C
MINIMUM
TYPICAL
6.5
11
7
5
115
135
140
-2.5
-3.3
-2
Class 2
2.9
3.1
3.3
2.25
MAXIMUM
1000
-5
3.5
3.7
3.9
2.6
150
It is highly recommended for the user to review the CREE XBD Series page for additional and most recent technical data at:
http://www.cree.com/led-components-and-modules/products/xlamp/discrete-directional/xlamp-xbd
Global Headquarters, 3 Northway Lane North, Latham, NY 12110, USA www.marktechopto.com
TOLL FREE: 1-800-984-5337 • PHONE: 518-956-2980 • FAX: 518-785-4725 • EMAIL: [email protected]
Cree XB-D Color Series on Board
* Exceeding maximum ratings may damage the LED and cause potential safety hazards.
* Elevated operating temperatures can be expected to negatively impact the service life (lumen output)
* All data is related to entire assembly. Data reflects statistical mean values. Actual data may differ depending on variances
in the manufacturing process.
* End users need to take into account the lumen depreciation as the temperature rises with various thermal solutions
installed.
Note 1: Using continuously under elevated loads (i.e. the application of high temperature/current/voltage or a significant
change in temperature, etc.) may cause this product to significantly decrease in reliability even if the operating conditions are
within the
absolute maximum ratings.
Note 2: The thermal resistance from the LED junction to ambient temperature, Rth(j-a), should be kept below 100C/W so that
the LED is not exposed to a condition beyond the absolute maximum ratings.
Note 3: The temperature of the LED assembly must be measured at the TC-point according to EN60598-1 in a thermally
constant status with a temperature sensor or a temperature sensitive label.
Hardware (not included)
> Mount with #4 Machine Screws.
> 16AWG Maximum Wire Gauge.
> Use only with constant current power supplies.
PCB Fabrication
> Layer Count: 1
> Core Material: 6061-T6 Aluminum
> Single Layer Copper Weight: 1oz
> Solder Mask: White
> Finishing Plating: Pb Free HASL
Global Headquarters, 3 Northway Lane North, Latham, NY 12110, USA www.marktechopto.com
TOLL FREE: 1-800-984-5337 • PHONE: 518-956-2980 • FAX: 518-785-4725 • EMAIL: [email protected]
Similar pages