TDK MLZ2012P220WT000 Inductors for decoupling circuits multilayer ferrite Datasheet

I
N
D
U
C
T
O
R
S
April 2016
Inductors for Decoupling Circuits
Multilayer Ferrite
MLZ Series
MLZ2012 Type
MLZ2012
2012 [0805 inch]*
* Dimensions Code JIS[EIA]
(2/15)
I
N
D
U
C
T
O
R
S
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
20160411 / inductor_commercial_decoupling_mlz2012_en.fm
(3/15)
I
N
D
U
C
T
O
R
S
Inductors for Decoupling Circuits
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
Multilayer Ferrite
Overview of MLZ2012 Type
FEATURES
The MLZ Series include inductors for decoupling circuits that have top-class DC superimposition characteristics and low DC resistance.
They are compatible with wide frequency band noise, from low to high frequency.
H type products have a rated current that is equivalent to that of wound coils.
W type products are the new standard type products that have both large current and low resistance.
L type products have a resistance up to 60% lower than W type products.
APPLICATION
Smart phones, tablet terminals, note PCs, various modules such as camera modules, DSCs, video games, portable memory audio
devices, navigation systems, PNDs, WLANs, SSDs
PART NUMBER CONSTRUCTION
MLZ
Series name
2012
M
1R0
L×W×H Dimensions
(mm)
2.0×1.25×0.85
2012
2.0×1.25×1.25
Product
internal code
A
D
M
N
Inductance
(μH)
1R0
1
100
10
101
100
H
T
000
Characteristic type
Packaging style
Internal code
H
D
W
L
Ultra-large current type
High frequency type
Large current type
Low resistance type
T
Taping
000
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Type
Operating
temperature
(°C)
Package quantity
Individual weight
(pieces/reel)
4000
2000
(mg)
10
14
Storage
temperature
(°C)
t=0.85
MLZ2012
–55 to +125
–55 to +125
t=1.25
Operating temperature range includes self-temperature rise.
The Storage temperature range is for after the circuit board is mounted.
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_decoupling_mlz2012_en.fm
(4/15)
I
N
D
U
C
T
O
R
S
MLZ2012 Type
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T: Temperature
T4
T3
T2
T3
t3
T1
t1
t2
t: Time
Preheating
Temp.
T1
T2
150°C
180°C
Time
t1
60 to 120s
Soldering
Temp.
Time
T3
t2
230°C
30 to 60s
Peak
Temp.
T4
250 to 260°C
Time
t3
10s max.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_decoupling_mlz2012_en.fm
(5/15)
I
N
D
U
C
T
O
R
S
MLZ2012 Type
1.25±0.20
SHAPE & DIMENSIONS
0.50±0.30
0.50±0.30
T
2.00±0.20
T
0.85±0.20
1.25±0.20
Dimensions in mm
1.2
RECOMMENDED LAND PATTERN
0.8
1.0
0.8
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_decoupling_mlz2012_en.fm
(6/15)
I
N
D
U
C
T
O
R
S
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Type
L
(μH)
1.0
1.5
2.2
Ultra-large
3.3
current
4.7
6.8
10
0.10
High
0.22
frequency
0.47
1.00
1.50
2.20
3.30
4.70
6.80
Large current
10.0
15.0
22.0
22.0
33.0
47.0
1.00
1.50
2.20
3.30
4.70
Low
resistance
6.80
10.0
15.0
22.0
100.0
1
2
Tolerance
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
Thickness
L measuring conditions
T
Frequency
Current
(mm)
1.25
1.25
1.25
1.25
1.25
1.25
1.25
0.85
0.85
1.25
0.85
0.85
0.85
0.85
0.85
1.25
1.25
1.25
1.25
1.25
1.25
1.25
0.85
0.85
0.85
0.85
0.85
0.85
1.25
1.25
1.25
1.25
(MHz)
2
2
2
2
2
2
2
25
25
25
10
10
10
10
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(mA)
0.1
0.1
0.1
0.1
0.1
0.1
0.1
1.0
1.0
1.0
1.0
1.0
1.0
1.0
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
DC resistance Isat1
Itemp2
Part No.
( )±30%
0.10
0.14
0.16
0.20
0.34
0.40
0.68
0.07
0.13
0.18
0.10
0.13
0.15
0.34
0.30
0.40
0.47
0.95
1.25
2.0
2.60
3.70
0.06
0.10
0.12
0.15
0.18
0.25
0.30
0.47
0.67
3.50
(mA)
800
700
600
500
400
350
300
1150
900
700
900
750
650
450
500
400
350
250
220
220
190
170
1150
900
800
750
600
550
500
350
300
140
MLZ2012M1R0HT000
MLZ2012M1R5HT000
MLZ2012M2R2HT000
MLZ2012M3R3HT000
MLZ2012M4R7HT000
MLZ2012M6R8HT000
MLZ2012M100HT000
MLZ2012DR10DT000
MLZ2012DR22DT000
MLZ2012DR47DT000
MLZ2012A1R0WT000
MLZ2012A1R5WT000
MLZ2012A2R2WT000
MLZ2012A3R3WT000
MLZ2012M4R7WT000
MLZ2012M6R8WT000
MLZ2012M100WT000
MLZ2012M150WT000
MLZ2012P220WT000
MLZ2012M220WT000
MLZ2012M330WT000
MLZ2012M470WT000
MLZ2012N1R0LT000
MLZ2012N1R5LT000
MLZ2012N2R2LT000
MLZ2012N3R3LT000
MLZ2012N4R7LT000
MLZ2012N6R8LT000
MLZ2012N100LT000
MLZ2012N150LT000
MLZ2012N220LT000
MLZ2012N101LT000
(mA)
700
550
400
350
300
220
200
1000
800
550
280
250
210
200
180
160
150
120
100
60
55
50
220
190
170
130
130
110
110
90
70
30
Current assumed when inductance ratio has decreased by 50% max..
Current assumed when temperature has risen to 20°C max. (reference value).
Operating temperature environment at this time: 105°C max.
○ Measurement equipment
Measurement item
Product No.
L
4294A+16034G
DC resistance
Type-7561
* Equivalent measurement equipment may be used.
Manufacturer
Keysight Technologies
Yokogawa
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_decoupling_mlz2012_en.fm
(7/15)
I
N
D
U
C
T
O
R
S
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
H CHARACTERISTIC PRODUCT
100
M100H
Inductance(μH)
10
M6R8H
M4R7H
M3R3H
M2R2H
M1R5H
M1R0H
1
0.1
1
10
100
1000
100
1000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
Keysight Technologies
E4991A+16192A
* Equivalent measurement equipment may be used.
L FREQUENCY CHARACTERISTICS GRAPH
D CHARACTERISTIC PRODUCT
1000
Inductance(μH)
100
10
1
DR47D
DR22D
DR10D
0.1
0.01
1
10
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991A+16192A
Keysight Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_decoupling_mlz2012_en.fm
(8/15)
I
N
D
U
C
T
O
R
S
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
W CHARACTERISTIC PRODUCT
1000
M470W
M330W
P220W
100
M220W
M150W
M100W
M6R8W
Inductance(μH)
10
M4R7W
A3R3W
A2R2W
1
A1R5W
A1R0W
0.1
0.01
1
10
100
1000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
Keysight Technologies
E4991A+16192A
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_decoupling_mlz2012_en.fm
(9/15)
I
N
D
U
C
T
O
R
S
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
L CHARACTERISTIC PRODUCT
1000
N101L
100
N220L
Inductance(μH)
N150L
N100L
10
N6R8L
N4R7L
N3R3L
1
N2R2L
N1R5L
0.1
N1R0L
0.01
1
10
100
1000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
Keysight Technologies
E4991A+16192A
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_decoupling_mlz2012_en.fm
(10/15)
I
N
D
U
C
T
O
R
S
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
H CHARACTERISTIC PRODUCT
100
M100H
Inductance(μH)
10
M6R8H
M4R7H
M3R3H
M2R2H
M1R5H
M1R0H
1
0.1
0
200
400
600
800
1000
800
1000
DC current(mA)
○ Measurement equipment
Product No.
Manufacturer
4291B+16200A+16192A
Keysight Technologies
* Equivalent measurement equipment may be used.
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
D CHARACTERISTIC PRODUCT
Inductance(μH)
10
1
DR47D
DR22D
0.1 DR10D
0.01
0
200
400
600
DC current(mA)
○ Measurement equipment
Product No.
Manufacturer
4291B+16200A+16192A
Keysight Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_decoupling_mlz2012_en.fm
(11/15)
I
N
D
U
C
T
O
R
S
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH (EXAMPLE)
W CHARACTERISTIC PRODUCT
1000
M330W
100
Inductance(μH)
M470W
P220W
M100W
10
M4R7W
M150W
M220W
1
M6R8W
0.1
0
100
200
300
400
DC current(mA)
500
600
700
○ Measurement equipment
Product No.
Manufacturer
4291B+16200A+16192A
Keysight Technologies
* Equivalent measurement equipment may be used.
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
L CHARACTERISTIC PRODUCT
1000
N101L
Inductance(μH)
100
N220L
10
N150L
N100L
N6R8L
N3R3L
1
N1R0L
N4R7L
N2R2L
N1R5L
0.1
0
100
200
300
400
500
DC current(mA)
○ Measurement equipment
Product No.
Manufacturer
4291B+16200A+16192A
Keysight Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_decoupling_mlz2012_en.fm
(12/15)
I
N
D
U
C
T
O
R
S
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH
H CHARACTERISTIC PRODUCT
100000
M100H
10000
M6R8H
M4R7H
M3R3H
M2R2H
Impedance(Ω)
M1R5H
1000
M1R0H
100
10
1
1
10
100
1000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991A+16192A
Keysight Technologies
* Equivalent measurement equipment may be used.
IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH
D CHARACTERISTIC PRODUCT
10000
DR47D
DR22D
Impedance(Ω)
1000
DR10D
100
10
1
1
10
100
1000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991A+16192A
Keysight Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_decoupling_mlz2012_en.fm
(13/15)
I
N
D
U
C
T
O
R
S
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH
W CHARACTERISTIC PRODUCT
1000000
M330W
100000
P220W
M220W
M470W
M150W
10000
M6R8W
M100W
Impedance(Ω)
A3R3W
1000
A1R0W
A1R5W
A2R2W
M4R7W
100
10
1
1
10
100
1000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991A+16192A
Keysight Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_decoupling_mlz2012_en.fm
(14/15)
I
N
D
U
C
T
O
R
S
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH
L CHARACTERISTIC PRODUCT
100000
N101L
Impedance(Ω)
10000
N220L
N150L
N100L
1000
N6R8L
N1R0L
100
N4R7L
N3R3L
N2R2L
N1R5L
10
1
1
10
100
1000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991A+16192A
Keysight Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_decoupling_mlz2012_en.fm
(15/15)
I
N
D
U
C
T
O
R
S
MLZ2012 Type
PACKAGING STYLE
REEL DIMENSIONS
ø60min.
1.0
2.0±0.5
8.4 +2.0
–0.0
ø13±0.2
14.4max.
ø21±0.8
ø180±2.0
Dimensions in mm
4.0±0.1
B
4.0±0.1
A
Type
MLZ2012
MLZ2012 (t=0.85) MLZ2012 (t=1.25)
8.0±0.3
2.0±0.05
F
1.5 +0.1
0
1.75±0.1
TAPE DIMENSIONS
t=0.85
t=1.25
160min.
Drawing direction
A
1.5±0.2
1.5±0.2
Taping
B
2.3±0.2
2.3±0.2
K
K
Dimensions in mm
K
1.1 max.
1.5 max.
200min.
300min.
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_decoupling_mlz2012_en.fm
Similar pages