AD ADuM230D1BRWZ-RL 5.0 kv rms triple channel digital isolator Datasheet

FUNCTIONAL BLOCK DIAGRAMS
VDD1 1
GND1 2
VIA 3
VIB 4
VIC 5
NIC 6
DISABLE1 7
GND1 8
ENCODE
DECODE
15 GND2
14 VOA
ENCODE
DECODE
13 VOB
ENCODE
DECODE
12 VOC
11 NIC
10 NIC
9
GND2
Figure 1. ADuM230D Functional Block Diagram
1
ADuM230E
2
3
ENCODE
DECODE
4
ENCODE
DECODE
ENCODE
DECODE
5
NIC 6
NIC 7
GND1 8
16 VDD2
15 GND2
14 VOA
13 VOB
12 VOC
11 NIC
10 VE2
9 GND2
NIC = NO INTERNAL CONNECTION. LEAVE THIS PIN FLOATING.
13577-002
VDD1
GND1
VIA
VIB
VIC
Figure 2. ADuM230E Functional Block Diagram
VDD1
GND1
VIA
VIB
VOC
1
ADuM231D
2
16 VDD2
15 GND2
3
ENCODE
DECODE
14 VOA
4
ENCODE
DECODE
DECODE
ENCODE
13 VOB
12 VIC
5
NIC 6
DISABLE1 7
GND1 8
11 NIC
10 DISABLE2
9 GND2
NIC = NO INTERNAL CONNECTION. LEAVE THIS PIN FLOATING.
Figure 3. ADuM231D Functional Block Diagram
GENERAL DESCRIPTION
The ADuM230D/ADuM230E/ADuM231D/ADuM231E1 are
triple-channel digital isolators based on Analog Devices, Inc.,
iCoupler® technology. Combining high speed, complementary
metal-oxide semiconductor (CMOS) and monolithic air core
transformer technology, these isolation components provide
outstanding performance characteristics superior to alternatives
such as optocoupler devices and other integrated couplers. The
maximum propagation delay is 13 ns with a pulse width
distortion of less than 3 ns at 5 V operation. Channel matching
is tight at 3.0 ns maximum.
The ADuM230D/ADuM230E/ADuM231D/ADuM231E data
channels are independent and are available in a variety of
configurations with a withstand voltage rating of 5.0 kV rms
(see the Ordering Guide). The devices operate with the supply
voltage on either side ranging from 1.8 V to 5 V, providing
compatibility with lower voltage systems as well as enabling
voltage translation functionality across the isolation barrier.
1
16 VDD2
NIC = NO INTERNAL CONNECTION. LEAVE THIS PIN FLOATING.
APPLICATIONS
General-purpose multichannel isolation
Serial peripheral interface (SPI)/data converter isolation
Industrial field bus isolation
ADuM230D
13577-101
High common-mode transient immunity: 100 kV/μs
High robustness to radiated and conducted noise
Low propagation delay: 13 ns maximum for 5 V operation,
15 ns maximum for 1.8 V operation
150 Mbps maximum data rate
Safety and regulatory approvals (pending)
UL recognition
5000 V rms for 1 minute per UL 1577
CSA Component Acceptance Notice 5A
VDE certificate of conformity
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12
VIORM = 849 V peak
8000 V peak reinforced surge isolation voltage (VIOSM)
CQC certification per GB4943.1-2011
Low dynamic power consumption
1.8 V to 5 V level translation
High temperature operation: 125°C
Fail-safe high or low options
16-lead, RoHS compliant, SOIC package
13577-001
FEATURES
VDD1
GND1
VIA
VIB
VOC
1
ADuM231E
2
3
ENCODE
DECODE
4
ENCODE
DECODE
DECODE
ENCODE
5
NIC 6
VE1 7
GND1 8
16 VDD2
15 GND2
14 VOA
13 VOB
12 VIC
11 NIC
10 VE2
9 GND2
NIC = NO INTERNAL CONNECTION. LEAVE THIS PIN FLOATING.
13577-102
Data Sheet
5.0 kV RMS Triple Channel Digital Isolators
ADuM230D/ADuM230E/ADuM231D/ADuM231E
Figure 4. ADuM231E Functional Block Diagram
Unlike other optocoupler alternatives, dc correctness is ensured
in the absence of input logic transitions. Two different fail-safe
options are available, by which the outputs transition to a
predetermined state when the input power supply is not applied
or the inputs are disabled.
Protected by U.S. Patents 5,952,849; 6,873,065; 6,903,578; and 7,075,329. Other patents are pending.
Rev. A
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2015–2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADuM230D/ADuM230E/ADuM231D/ADuM231E
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Recommended Operating Conditions .................................... 11
Applications ....................................................................................... 1
Absolute Maximum Ratings ......................................................... 12
General Description ......................................................................... 1
ESD Caution................................................................................ 12
Functional Block Diagrams ............................................................. 1
Pin Configurations and Function Descriptions ......................... 14
Revision History ............................................................................... 2
Typical Performance Characteristics ........................................... 16
Specifications..................................................................................... 3
Theory of Operation ...................................................................... 17
Electrical Characteristics—5 V Operation................................ 3
Applications Information .............................................................. 18
Electrical Characteristics—3.3 V Operation ............................ 4
PCB Layout ................................................................................. 18
Electrical Characteristics—2.5 V Operation ............................ 6
Propagation Delay Related Parameters ................................... 18
Electrical Characteristics—1.8 V Operation ............................ 7
Jitter Measurement ..................................................................... 18
Insulation and Safety Related Specifications ............................ 9
Insulation Lifetime ..................................................................... 18
Package Characteristics ............................................................... 9
Outline Dimensions ....................................................................... 20
Regulatory Information ............................................................. 10
Ordering Guide .......................................................................... 21
DIN V VDE V 0884-10 (VDE V 0884-10) Insulation
Characteristics ............................................................................ 11
REVISION HISTORY
4/16—Rev. 0 to Rev. A
Added RI-16-2 .................................................................... Universal
Added Table 10; Renumbered Sequentially .................................. 9
Added Table 13 ............................................................................... 10
Added Table 18 ............................................................................... 12
Added Figure 23.............................................................................. 20
Updated Outline Dimensions ....................................................... 20
Changes to Ordering Guide .......................................................... 21
10/15—Revision 0: Initial Version
Rev. A | Page 2 of 21
Data Sheet
ADuM230D/ADuM230E/ADuM231D/ADuM231E
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS—5 V OPERATION
All typical specifications are at TA = 25°C, VDD1 = VDD2 = 5 V. Minimum/maximum specifications apply over the entire recommended
operation range of 4.5 V ≤ VDD1 ≤ 5.5 V, 4.5 V ≤ VDD2 ≤ 5.5 V, and −40°C ≤ TA ≤ +125°C, unless otherwise noted. Switching specifications
are tested with CL = 15 pF and CMOS signal levels, unless otherwise noted. Supply currents are specified with 50% duty cycle signals.
Table 1.
Parameter
SWITCHING SPECIFICATIONS
Pulse Width
Data Rate1
Propagation Delay
Pulse Width Distortion
Change vs. Temperature
Propagation Delay Skew
Channel Matching
Codirectional
Opposing Direction
Jitter
DC SPECIFICATIONS
Input Threshold Voltage
Logic High
Symbol
Min
PW
6.6
150
4.8
tPHL, tPLH
PWD
7.2
0.5
1.5
tPSK
VIH
VIL
Output Voltage
Logic High
VOH
Logic Low
VOL
Max
Unit
Test Conditions/Comments
13
3
ns
Mbps
ns
ns
ps/°C
ns
Within pulse width distortion (PWD) limit
Within PWD limit
50% input to 50% output
|tPLH − tPHL|
6.1
tPSKCD
tPSKOD
Logic Low
Input Current per Channel
VE2 Enable Input Pull-Up Current
DISABLE1 Input Pull-Down Current
Tristate Output Current per Channel
Quiescent Supply Current
ADuM230D/ADuM230E
Typ
0.5
0.5
630
80
3.0
3.0
ns
ns
ps p-p
ps rms
Between any two devices at the
same temperature, voltage, and load
See the Jitter Measurement section
See the Jitter Measurement section
V
0.7 ×
VDDx
0.3 ×
VDDx
V
V
V
IOx2 = −20 μA, VIx = VIxH3
IOx2 = −4 mA, VIx = VIxH3
15
+10
V
V
μA
μA
μA
μA
IOx2 = 20 μA, VIx = VIxL4
IOx2 = 4 mA, VIx = VIxL4
0 V ≤ VIx ≤ VDDx
VE2 = 0 V
DISABLE1 = VDDx
0 V ≤ VOx ≤ VDDx
1.35
1.73
9.7
1.87
2.6
2.9
15.2
3.0
mA
mA
mA
mA
VI5 = 0 (E0, D0), 1 (E1, D1)6
VI5 = 0 (E0, D0), 1 (E1, D1)6
VI5 = 1 (E0, D0), 0 (E1, D1)6
VI5 = 1 (E0, D0), 0 (E1, D1)6
IDD1 (Q)
IDD2 (Q)
IDD1 (Q)
IDD2 (Q)
1.62
1.61
7.4
5.34
2.7
2.8
11.4
7.2
mA
mA
mA
mA
VI5 = 0 (E0, D0), 1 (E1, D1)6
VI5 = 0 (E0, D0), 1 (E1, D1)6
VI5 = 1 (E0, D0), 0 (E1, D1)6
VI5 = 1 (E0, D0), 0 (E1, D1)6
IDDI (D)
IDDO (D)
0.01
0.02
mA/Mbps
mA/Mbps
Inputs switching, 50% duty cycle
Inputs switching, 50% duty cycle
VDDx
VDDx −
0.2
0.0
0.2
+0.01
−3
9
+0.01
IDD1 (Q)
IDD2 (Q)
IDD1 (Q)
IDD2 (Q)
II
IPU
IPD
IOZ
VDDx − 0.1
VDDx − 0.4
−10
−10
−10
0.1
0.4
+10
ADuM231D/ADuM231E
Dynamic Supply Current
Dynamic Input
Dynamic Output
Rev. A | Page 3 of 21
ADuM230D/ADuM230E/ADuM231D/ADuM231E
Parameter
Undervoltage Lockout
Positive VDDx Threshold
Negative VDDx Threshold
VDDx Hysteresis
AC SPECIFICATIONS
Output Rise/Fall Time
Common-Mode Transient Immunity7
Symbol
UVLO
VDDxUV+
VDDxUV−
VDDxUVH
Min
Typ
Data Sheet
Max
Unit
1.6
1.5
0.1
V
V
V
tR/tF
|CMH|
75
2.5
100
ns
kV/μs
|CML|
75
100
kV/μs
Test Conditions/Comments
10% to 90%
VIx = VDDx, VCM = 1000 V,
transient magnitude = 800 V
VIx = 0 V, VCM = 1000 V,
transient magnitude = 800 V
1
150 Mbps is the highest data rate that can be guaranteed, although higher data rates are possible.
IOx is the Channel x output current, where x = A, B, or C.
3
VIxH is the input side logic high.
4
VIxL is the input side logic low.
5
VI is the voltage input.
6
E0 refers to the ADuM230E0/ADuM231E0 models, D0 refers to the ADuM230D0/ADuM231D0 models, E1 refers to the ADuM230E1/ADuM231E1 models, and D1 refers
to the ADuM230D1/ADuM231D1 models. See the Ordering Guide section.
7
|CMH| is the maximum common-mode voltage slew rate that can be sustained while maintaining the voltage output (VOx) > 0.8 VDDx. |CML| is the maximum commonmode voltage slew rate that can be sustained while maintaining VOx > 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode
voltage edges.
2
Table 2. Total Supply Current vs. Data Throughput
Parameter
SUPPLY CURRENT
ADuM230D/ADuM230E
Supply Current Side 1
Supply Current Side 2
ADuM231D/ADuM231E
Supply Current Side 1
Supply Current Side 2
Symbol
Min
1 Mbps
Typ
Max
Min
25 Mbps
Typ
Max
Min
100 Mbps
Typ
Max
Unit
IDD1
IDD2
5.6
1.9
9.0
3.7
6.3
3.1
9.8
4.9
9.4
6.8
14.3
10
mA
mA
IDD1
IDD2
4.6
3.6
7.2
5.8
5.5
4.6
8.3
6.8
8.8
8.0
11.9
11.3
mA
mA
ELECTRICAL CHARACTERISTICS—3.3 V OPERATION
All typical specifications are at TA = 25°C, VDD1 = VDD2 = 3.3 V. Minimum/maximum specifications apply over the entire recommended
operation range: 3.0 V ≤ VDD1 ≤ 3.6 V, 3.0 V ≤ VDD2 ≤ 3.6 V, and −40°C ≤ TA ≤ +125°C, unless otherwise noted. Switching specifications
are tested with CL = 15 pF and CMOS signal levels, unless otherwise noted. Supply currents are specified with 50% duty cycle signals.
Table 3.
Parameter
SWITCHING SPECIFICATIONS
Pulse Width
Data Rate1
Propagation Delay
Pulse Width Distortion
Change vs. Temperature
Propagation Delay Skew
Channel Matching
Codirectional
Opposing Direction
Jitter
DC SPECIFICATIONS
Input Threshold Voltage
Logic High
Logic Low
Symbol
Min
PW
6.6
150
4.8
tPHL, tPLH
PWD
Typ
6.8
0.7
1.5
tPSK
Unit
Test Conditions/Comments
14
3
ns
Mbps
ns
ns
ps/°C
ns
Within PWD limit
Within PWD limit
50% input to 50% output
|tPLH − tPHL|
7.5
tPSKCD
tPSKOD
VIH
VIL
Max
0.7
0.7
640
75
3.0
3.0
0.7 × VDDx
0.3 × VDDx
Rev. A | Page 4 of 21
ns
ns
ps p-p
ps rms
V
V
Between any two devices at the same
temperature, voltage, and load
See the Jitter Measurement section
See the Jitter Measurement section
Data Sheet
ADuM230D/ADuM230E/ADuM231D/ADuM231E
Parameter
Output Voltage
Logic High
Logic Low
Symbol
Min
Typ
VOH
VDDx − 0.1
VDDx − 0.4
VDDx
VDDx − 0.2
0.0
0.2
+0.01
−3
9
+0.01
Unit
Test Conditions/Comments
15
+10
V
V
V
V
μA
μA
μA
μA
IOx2 = −20 μA, VIx = VIxH3
IOx2 = −2 mA, VIx = VIxH3
IOx2 = 20 μA, VIx = VIxL4
IOx2 = 2 mA, VIx = VIxL4
0 V ≤ VIx ≤ VDDx
VE2 = 0 V
DISABLE1 = VDDx
0 V ≤ VOx ≤ VDDx
IDD1 (Q)
IDD2 (Q)
IDD1 (Q)
IDD2 (Q)
1.25
1.65
9.57
1.79
2.5
2.8
15.0
2.9
mA
mA
mA
mA
VI5 = 0 (E0, D0), 1 (E1, D1)6
VI5 = 0 (E0, D0), 1 (E1, D1)6
VI5 = 1 (E0, D0), 0 (E1, D1)6
VI5 = 1 (E0, D0), 0 (E1, D1)6
IDD1 (Q)
IDD2 (Q)
IDD1 (Q)
IDD2 (Q)
1.52
1.52
7.28
5.24
2.6
2.6
11.3
7.1
mA
mA
mA
mA
VI5 = 0 (E0, D0), 1 (E1, D1)6
VI5 = 0 (E0, D0), 1 (E1, D1)6
VI5 = 1 (E0, D0), 0 (E1, D1)6
VI5 = 1 (E0, D0), 0 (E1, D1)6
IDDI (D)
IDDO (D)
UVLO
VDDxUV+
VDDxUV−
VDDxUVH
0.01
0.01
mA/Mbps
mA/Mbps
Inputs switching, 50% duty cycle
Inputs switching, 50% duty cycle
1.6
1.5
0.1
V
V
V
VOL
Input Current per Channel
VE2 Enable Input Pull-Up Current
DISABLE1 Input Pull-Down Current
Tristate Output Current per Channel
Quiescent Supply Current
ADuM230D/ADuM230E
II
IPU
IPD
IOZ
−10
−10
−10
Max
0.1
0.4
+10
ADuM231D/ADuM231E
Dynamic Supply Current
Dynamic Input
Dynamic Output
Undervoltage Lockout
Positive VDDx Threshold
Negative VDDx Threshold
VDDx Hysteresis
AC SPECIFICATIONS
Output Rise/Fall Time
Common-Mode Transient Immunity7
tR/tF
|CMH|
75
2.5
100
ns
kV/μs
|CML|
75
100
kV/μs
10% to 90%
VIx = VDDx, VCM = 1000 V,
transient magnitude = 800 V
VIx = 0 V, VCM = 1000 V,
transient magnitude = 800 V
1
150 Mbps is the highest data rate that can be guaranteed, although higher data rates are possible.
IOx is the Channel x output current, where x = A, B, or C.
3
VIxH is the input side logic high.
4
VIxL is the input side logic low.
5
VI is the voltage input.
6
E0 refers to the ADuM230E0/ADuM231E0 models, D0 refers to the ADuM230D0/ADuM231D0 models, E1 refers to the ADuM230E1/ADuM231E1 models, and D1 refers
to the ADuM230D1/ADuM231D1 models. See the Ordering Guide section.
7
|CMH| is the maximum common-mode voltage slew rate that can be sustained while maintaining the voltage output (VOx) > 0.8 VDDx. |CML| is the maximum commonmode voltage slew rate that can be sustained while maintaining VOx > 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode
voltage edges.
2
Table 4. Total Supply Current vs. Data Throughput
Parameter
SUPPLY CURRENT
ADuM230D/ADuM230E
Supply Current Side 1
Supply Current Side 2
ADuM231D/ADuM231E
Supply Current Side 1
Supply Current Side 2
Symbol
Min
1 Mbps
Typ
Max
Min
25 Mbps
Typ
Max
Min
100 Mbps
Typ
Max
Unit
IDD1
IDD2
5.4
1.8
8.8
3.6
6.0
2.9
9.4
4.7
8.5
6.2
12.7
8.4
mA
mA
IDD1
IDD2
4.4
3.4
7.1
5.6
5.2
4.3
8.0
6.5
8.1
7.4
10.7
9.5
mA
mA
Rev. A | Page 5 of 21
ADuM230D/ADuM230E/ADuM231D/ADuM231E
Data Sheet
ELECTRICAL CHARACTERISTICS—2.5 V OPERATION
All typical specifications are at TA = 25°C, VDD1 = VDD2 = 2.5 V. Minimum/maximum specifications apply over the entire recommended
operation range: 2.25 V ≤ VDD1 ≤ 2.75 V, 2.25 V ≤ VDD2 ≤ 2.75 V, −40°C ≤ TA ≤ +125°C, unless otherwise noted. Switching specifications
are tested with CL = 15 pF and CMOS signal levels, unless otherwise noted. Supply currents are specified with 50% duty cycle signals.
Table 5.
Parameter
SWITCHING SPECIFICATIONS
Pulse Width
Data Rate1
Propagation Delay
Pulse Width Distortion
Change vs. Temperature
Propagation Delay Skew
Channel Matching
Codirectional
Opposing Direction
Jitter
DC SPECIFICATIONS
Input Threshold Voltage
Logic High
Logic Low
Output Voltage
Logic High
Logic Low
Input Current per Channel
VE2 Enable Input Pull-Up Current
DISABLE1 Input Pull-Down Current
Tristate Output Current per Channel
Quiescent Supply Current
ADuM230D/ADuM230E
Symbol
Min
PW
6.6
150
5.0
tPHL, tPLH
PWD
Typ
7.0
0.7
1.5
tPSK
Max
Unit
Test Conditions/Comments
14
3
ns
Mbps
ns
ns
ps/°C
ns
Within PWD limit
Within PWD limit
50% input to 50% output
|tPLH − tPHL|
6.8
tPSKCD
tPSKOD
0.7
0.7
770
160
VIH
VIL
0.7 × VDDx
VOH
VDDx − 0.1
VDDx − 0.4
3.0
3.0
0.3 × VDDx
ns
ns
ps p-p
ps rms
Between any two devices at the
same temperature, voltage, and load
See the Jitter Measurement section
See the Jitter Measurement section
V
V
15
+10
V
V
V
V
μA
μA
μA
μA
IOx2 = −20 μA, VIx = VIxH3
IOx2 = −2 mA, VIx = VIxH3
IOx2 = 20 μA, VIx = VIxL4
IOx2 = 2 mA, VIx = VIxL4
0 V ≤ VIx ≤ VDDx
VE2 = 0 V
DISABLE1 = VDDx
0 V ≤ VOx ≤ VDDx
1.2
1.61
9.52
1.76
2.4
2.7
14.9
2.8
mA
mA
mA
mA
VI5 = 0 (E0, D0), 1 (E1, D1)6
VI5 = 0 (E0, D0), 1 (E1, D1)6
VI5 = 1 (E0, D0), 0 (E1, D1)6
VI5 = 1 (E0, D0), 0 (E1, D1)6
IDD1 (Q)
IDD2 (Q)
IDD1 (Q)
IDD2 (Q)
1.47
1.48
7.23
5.19
2.5
2.5
11.2
7.0
mA
mA
mA
mA
VI5 = 0 (E0, D0), 1 (E1, D1)6
VI5 = 0 (E0, D0), 1 (E1, D1)6
VI5 = 1 (E0, D0), 0 (E1, D1)6
VI5 = 1 (E0, D0), 0 (E1, D1)6
IDDI (D)
IDDO (D)
0.01
0.01
mA/Mbps
mA/Mbps
Inputs switching, 50% duty cycle
Inputs switching, 50% duty cycle
VDDxUV+
VDDxUV−
VDDxUVH
1.6
1.5
0.1
V
V
V
VDDx
VDDx − 0.2
0.0
0.2
+0.01
−3
9
+0.01
IDD1 (Q)
IDD2 (Q)
IDD1 (Q)
IDD2 (Q)
VOL
II
IPU
IPD
IOZ
−10
−10
−10
0.1
0.4
+10
ADuM231D/ADuM231E
Dynamic Supply Current
Dynamic Input
Dynamic Output
Undervoltage Lockout
Positive VDDx Threshold
Negative VDDx Threshold
VDDx Hysteresis
Rev. A | Page 6 of 21
Data Sheet
ADuM230D/ADuM230E/ADuM231D/ADuM231E
Parameter
AC SPECIFICATIONS
Output Rise/Fall Time
Common-Mode Transient Immunity7
Symbol
Min
Typ
tR/tF
|CMH|
75
|CML|
75
Max
Unit
Test Conditions/Comments
2.5
100
ns
kV/μs
100
kV/μs
10% to 90%
VIx = VDDx, VCM = 1000 V,
transient magnitude = 800 V
VIx = 0 V, VCM = 1000 V,
transient magnitude = 800 V
1
150 Mbps is the highest data rate that can be guaranteed, although higher data rates are possible.
IOx is the Channel x output current, where x = A, B, or C.
VIxH is the input side logic high.
4
VIxL is the input side logic low.
5
VI is the voltage input.
6
E0 refers to the ADuM230E0/ADuM231E0 models, D0 refers to the ADuM230D0/ADuM231D0 models, E1 refers to the ADuM230E1/ADuM231E1 models, and D1 refers
to the ADuM230D1/ADuM231D1 models. See the Ordering Guide section.
7
|CMH| is the maximum common-mode voltage slew rate that can be sustained while maintaining the voltage output (VOx) > 0.8 VDDx. |CML| is the maximum commonmode voltage slew rate that can be sustained while maintaining VOx > 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode
voltage edges.
2
3
Table 6. Total Supply Current vs. Data Throughput
Parameter
SUPPLY CURRENT
ADuM230D/ADuM230E
Supply Current Side 1
Supply Current Side 2
ADuM231D/ADuM231E
Supply Current Side 1
Supply Current Side 2
Symbol
1 Mbps
Typ
Max
Min
Min
25 Mbps
Typ
Max
Min
100 Mbps
Typ
Max
Unit
IDD1
IDD2
5.3
1.8
8.7
3.6
5.9
2.6
9.3
4.4
8.2
5.2
12.3
7.4
mA
mA
IDD1
IDD2
4.4
3.4
7.1
5.6
5.0
4.1
7.8
6.3
7.5
6.6
10.1
8.7
mA
mA
ELECTRICAL CHARACTERISTICS—1.8 V OPERATION
All typical specifications are at TA = 25°C, VDD1 = VDD2 = 1.8 V. Minimum/maximum specifications apply over the entire recommended
operation range: 1.7 V ≤ VDD1 ≤ 1.9 V, 1.7 V ≤ VDD2 ≤ 1.9 V, and −40°C ≤ TA ≤ +125°C, unless otherwise noted. Switching specifications
are tested with CL = 15 pF and CMOS signal levels, unless otherwise noted. Supply currents are specified with 50% duty cycle signals.
Table 7.
Parameter
SWITCHING SPECIFICATIONS
Pulse Width
Data Rate1
Propagation Delay
Pulse Width Distortion
Change vs. Temperature
Propagation Delay Skew
Channel Matching
Codirectional
Opposing Direction
Jitter
DC SPECIFICATIONS
Input Threshold Voltage
Logic High
Logic Low
Symbol
Min
PW
6.6
150
5.8
tPHL, tPLH
PWD
Typ
8.7
0.7
1.5
tPSK
Unit
Test Conditions/Comments
15
3
ns
Mbps
ns
ns
ps/°C
ns
Within PWD limit
Within PWD limit
50% input to 50% output
|tPLH − tPHL|
7.0
tPSKCD
tPSKOD
VIH
VIL
Max
0.7
0.7
600
90
3.0
3.0
0.7 × VDDx
0.3 × VDDx
Rev. A | Page 7 of 21
ns
ns
ps p-p
ps rms
V
V
Between any two devices at the same
temperature, voltage, and load
See the Jitter Measurement section
See the Jitter Measurement section
ADuM230D/ADuM230E/ADuM231D/ADuM231E
Parameter
Output Voltage
Logic High
Logic Low
Symbol
Min
Typ
VOH
VDDx − 0.1
VDDx − 0.4
VDDx
VDDx − 0.2
0.0
0.2
+0.01
−3
9
+0.01
Unit
Test Conditions/Comments
15
+10
V
V
V
V
μA
μA
μA
μA
IOx2 = −20 μA, VIx = VIxH3
IOx2 = −2 mA, VIx = VIxH3
IOx2 = 20 μA, VIx = VIxL4
IOx2 = 2 mA, VIx = VIxL4
0 V ≤ VIx ≤ VDDx
VE2 = 0 V
DISABLE1 = VDDx
0 V ≤ VOx ≤ VDDx
IDD1 (Q)
IDD2 (Q)
IDD1 (Q)
IDD2 (Q)
1.15
1.58
9.41
1.72
2.3
2.6
14.8
2.7
mA
mA
mA
mA
VI5 = 0 (E0, D0), 1 (E1, D1)6
VI5 = 0 (E0, D0), 1 (E1, D1)6
VI5 = 1 (E0, D0), 0 (E1, D1)6
VI5 = 1 (E0, D0), 0 (E1, D1)6
IDD1 (Q)
IDD2 (Q)
IDD1 (Q)
IDD2 (Q)
1.42
1.44
7.15
5.13
2.4
2.4
11.1
6.9
mA
mA
mA
mA
VI5 = 0 (E0, D0), 1 (E1, D1)6
VI5 = 0 (E0, D0), 1 (E1, D1)6
VI5 = 1 (E0, D0), 0 (E1, D1)6
VI5 = 1 (E0, D0), 0 (E1, D1)6
IDDI (D)
IDDO (D)
UVLO
VDDxUV+
VDDxUV−
VDDxUVH
0.01
0.01
mA/Mbps
mA/Mbps
Inputs switching, 50% duty cycle
Inputs switching, 50% duty cycle
1.6
1.5
0.1
V
V
V
VOL
Input Current per Channel
VE2 Enable Input Pull-Up Current
DISABLE1 Input Pull-Down Current
Tristate Output Current per Channel
Quiescent Supply Current
ADuM230D/ADuM230E
Data Sheet
II
IPU
IPD
IOZ
−10
−10
−10
Max
0.1
0.4
+10
ADuM231D/ADuM231E
Dynamic Supply Current
Dynamic Input
Dynamic Output
Undervoltage Lockout
Positive VDDx Threshold
Negative VDDx Threshold
VDDx Hysteresis
AC SPECIFICATIONS
Output Rise/Fall Time
Common-Mode Transient Immunity7
tR/tF
|CMH|
75
2.5
100
ns
kV/μs
|CML|
75
100
kV/μs
10% to 90%
VIx = VDDx, VCM = 1000 V,
transient magnitude = 800 V
VIx = 0 V, VCM = 1000 V,
transient magnitude = 800 V
1
150 Mbps is the highest data rate that can be guaranteed, although higher data rates are possible.
IOx is the Channel x output current, where x = A, B, or C.
3
VIxH is the input side logic high.
4
VIxL is the input side logic low.
5
VI is the voltage input.
6
E0 refers to the ADuM230E0/ADuM231E0 models, D0 refers to the ADuM230D0/ADuM231D0 models, E1 refers to the ADuM230E1/ADuM231E1 models, and D1 refers
to the ADuM230D1/ADuM231D1 models. See the Ordering Guide section.
7
|CMH| is the maximum common-mode voltage slew rate that can be sustained while maintaining the voltage output (VOx) > 0.8 VDDx. |CML| is the maximum commonmode voltage slew rate that can be sustained while maintaining VOx > 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode
voltage edges.
2
Table 8. Total Supply Current vs. Data Throughput
Parameter
SUPPLY CURRENT
ADuM230D/ADuM230E
Supply Current Side 1
Supply Current Side 2
ADuM231D/ADuM231E
Supply Current Side 1
Supply Current Side 2
Symbol
Min
1 Mbps
Typ
Max
Min
25 Mbps
Typ
Max
Min
100 Mbps
Typ
Max
Unit
IDD1
IDD2
5.2
1.7
8.6
3.5
5.8
2.5
9.3
4.3
8.1
5.2
12.2
7.3
mA
mA
IDD1
IDD2
4.3
3.3
7.0
5.5
4.9
4.0
7.7
6.2
7.26
6.5
10.0
8.6
mA
mA
Rev. A | Page 8 of 21
Data Sheet
ADuM230D/ADuM230E/ADuM231D/ADuM231E
INSULATION AND SAFETY RELATED SPECIFICATIONS
For additional information, see www.analog.com/icouplersafety.
Table 9. RW-16 Wide Body [SOIC_W] Package
Parameter
Rated Dielectric Insulation Voltage
Minimum External Air Gap (Clearance)
Symbol
L (I01)
Value
5000
7.8
Unit
V rms
mm min
Minimum External Tracking (Creepage)
L (I02)
7.8
mm min
Minimum Clearance in the Plane of the Printed
Circuit Board (PCB Clearance)
L (PCB)
8.1
mm min
CTI
25.5
>400
II
μm min
V
Minimum Internal Gap (Internal Clearance)
Tracking Resistance (Comparative Tracking Index)
Material Group
Test Conditions/Comments
1-minute duration
Measured from input terminals to output terminals,
shortest distance through air
Measured from input terminals to output terminals,
shortest distance path along body
Measured from input terminals to output terminals,
shortest distance through air, line of sight, in the PCB
mounting plane
Insulation distance through insulation
DIN IEC 112/VDE 0303 Part 1
Material Group (DIN VDE 0110, 1/89, Table 1)
Table 10. RI-16 -2 Wide Body Increased Creepage [SOIC_IC] Package
Parameter
Rated Dielectric Insulation Voltage
Minimum External Air Gap (Clearance)
Symbol
L (I01)
Value
5000
8.3
Unit
V rms
mm min
Minimum External Tracking (Creepage)
L (I02)
8.3
mm min
Minimum Clearance in the Plane of the Printed
Circuit Board (PCB Clearance)
L (PCB)
8.3
mm min
CTI
25.5
>400
II
μm min
V
Minimum Internal Gap (Internal Clearance)
Tracking Resistance (Comparative Tracking Index)
Material Group
Test Conditions/Comments
1-minute duration
Measured from input terminals to output terminals,
shortest distance through air
Measured from input terminals to output terminals,
shortest distance path along body
Measured from input terminals to output terminals,
shortest distance through air, line of sight, in the PCB
mounting plane
Insulation distance through insulation
DIN IEC 112/VDE 0303 Part 1
Material Group (DIN VDE 0110, 1/89, Table 1)
PACKAGE CHARACTERISTICS
Table 11.
Parameter
Resistance (Input to Output)1
Capacitance (Input to Output)1
Input Capacitance2
IC Junction to Ambient Thermal Resistance
1
2
Symbol
RI-O
CI-O
CI
θJA
Min
Typ
1013
2.2
4.0
45
Max
Unit
Ω
pF
pF
°C/W
Test Conditions/Comments
f = 1 MHz
Thermocouple located at center of package underside
The device is considered a 2-terminal device: Pin 1 through Pin 8 are shorted together, and Pin 9 through Pin 16 are shorted together.
Input capacitance is from any input data pin to ground.
Rev. A | Page 9 of 21
ADuM230D/ADuM230E/ADuM231D/ADuM231E
Data Sheet
REGULATORY INFORMATION
See Table 17, Table 18, and the Insulation Lifetime section for details regarding recommended maximum working voltages for specific
cross-isolation waveforms and insulation levels.
Table 12. RW-16 Wide Body [SOIC_W] Package
UL (Pending)
Recognized Under 1577
Component Recognition
Program1
Single Protection, 5000 V rms
Isolation Voltage
Double Protection, 5000 V rms
Isolation Voltage
File E214100
1
2
CSA (Pending)
Approved under CSA Component Acceptance
Notice 5A
VDE (Pending)
Certified according to DIN V VDE V
0884-10 (VDE V 0884-10):2006-122
CSA 60950-1-07+A1+A2 and IEC 60950-1,
second edition, +A1+A2:
Basic insulation at 780 V rms (1103 V peak)
Reinforced insulation at 390 V rms (552 V peak)
IEC 60601-1 Edition 3.1:
Basic insulation (1 means of patient protection
(1 MOPP)), 490 V rms (686 V peak)
Reinforced insulation (2 MOPP), 238 V rms
(325 V peak)
CSA 61010-1-12 and IEC 61010-1 third edition:
Basic insulation at 300 V rms mains, 780 V
secondary (1103 V peak)
Reinforced insulation at 300 V rms Mains,
390 V secondary (552 V peak)
File 205078
Reinforced insulation, VIORM =
849 peak, VIOSM = 8000 V peak
Basic insulation, VIORM = 849 V peak,
VIOSM = 12 kV peak
File 2471900-4880-0001
CQC (Pending)
Certified by
CQC11-471543-2012,
GB4943.1-2011
Basic insulation at
780 V rms (1103 V peak)
Reinforced insulation at
389 V rms (552 V peak),
tropical climate, altitude
≤5000 meters
File (pending)
In accordance with UL 1577, each ADuM230D/ADuM230E/ADuM231D/ADuM231E is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 sec.
In accordance with DIN V VDE V 0884-10, each ADuM230D/ADuM230E/ADuM231D/ADuM231E is proof tested by applying an insulation test voltage ≥ 1018 V peak for
1 sec (partial discharge detection limit = 5 pC). The * marking branded on the component designates DIN V VDE V 0884-10 approval.
Table 13. RI-16 -2 Wide Body Increased Creepage [SOIC_IC] Package
UL (Pending)
Recognized Under 1577
Component Recognition
Program1
Single Protection, 5000 V rms
Isolation Voltage
Double Protection, 5000 V rms
Isolation Voltage
File E214100
1
2
CSA (Pending)
Approved under CSA Component Acceptance
Notice 5A
VDE (Pending)
Certified according to DIN V VDE V
0884-10 (VDE V 0884-10):2006-122
CSA 60950-1-07+A1+A2 and IEC 60950-1,
second edition, +A1+A2:
Basic insulation at 830 V rms (1174 V peak)
Reinforced insulation at 415 V rms (587 V peak)
IEC 60601-1 Edition 3.1:
Basic insulation (1 means of patient protection
(1 MOPP)), 519 V rms (734 V peak)
Reinforced insulation (2 MOPP), 261 V rms
(369 V peak)
CSA 61010-1-12 and IEC 61010-1 third edition:
Basic insulation at 300 V rms mains, 830 V
secondary (1174 V peak)
Reinforced insulation at 300 V rms Mains,
390 V secondary (587 V peak)
File 205078
Reinforced insulation, VIORM =
849 peak, VIOSM = 8000 V peak
Basic insulation, VIORM = 849 V peak,
VIOSM = 12 kV peak
File 2471900-4880-0001
CQC (Pending)
Certified by
CQC11-471543-2012,
GB4943.1-2011
Basic insulation at
830 V rms (1174 V peak)
Reinforced insulation at
415 V rms (587 V peak),
tropical climate, altitude
≤5000 meters
File (pending)
In accordance with UL 1577, each ADuM230D/ADuM230E/ADuM231D/ADuM231E is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 sec.
In accordance with DIN V VDE V 0884-10, each ADuM230D/ADuM230E/ADuM231D/ADuM231E is proof tested by applying an insulation test voltage ≥ 1018 V peak for
1 sec (partial discharge detection limit = 5 pC). The * marking branded on the component designates DIN V VDE V 0884-10 approval.
Rev. A | Page 10 of 21
Data Sheet
ADuM230D/ADuM230E/ADuM231D/ADuM231E
DIN V VDE V 0884-10 (VDE V 0884-10) INSULATION CHARACTERISTICS
These isolators are suitable for reinforced electrical isolation only within the safety limit data. Protective circuits ensure the maintenance
of the safety data. The * marking on packages denotes DIN V VDE V 0884-10 approval.
Table 14.
Description
Installation Classification per DIN VDE 0110
For Rated Mains Voltage ≤ 150 V rms
For Rated Mains Voltage ≤ 300 V rms
For Rated Mains Voltage ≤ 400 V rms
Climatic Classification
Pollution Degree per DIN VDE 0110, Table 1
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method B1
Test Conditions/Comments
VIORM × 1.875 = Vpd (m), 100% production test,
tini = tm = 1 sec, partial discharge < 5 pC
Input to Output Test Voltage, Method A
After Environmental Tests Subgroup 1
Characteristic
Unit
VIORM
Vpd (m)
I to IV
I to III
I to III
40/125/21
2
849
1592
V peak
V peak
1274
V peak
1019
V peak
VIOTM
VIOSM
8000
12,000
V peak
V peak
VIOSM
8000
V peak
TS
PS
RS
150
2.78
>109
°C
W
Ω
Vpd (m)
VIORM × 1.5 = Vpd (m), tini = 60 sec, tm = 10 sec,
partial discharge < 5 pC
VIORM × 1.2 = Vpd (m), tini = 60 sec, tm = 10 sec,
partial discharge < 5 pC
After Input and/or Safety Test Subgroup 2
and Subgroup 3
Highest Allowable Overvoltage
Surge Isolation Voltage Basic
VPEAK = 12.8 kV, 1.2 μs rise time, 50 μs,
50% fall time
VPEAK = 12.8 kV, 1.2 μs rise time, 50 μs,
50% fall time
Maximum value allowed in the event of a
failure (see Figure 5)
Surge Isolation Voltage Reinforced
Safety Limiting Values
Maximum Junction Temperature
Total Power Dissipation at 25°C
Insulation Resistance at TS
SAFE LIMITING POWER (W)
Symbol
VIO = 500 V
3.0
RECOMMENDED OPERATING CONDITIONS
2.5
Table 15.
Parameter
Operating Temperature
Supply Voltages
Input Signal Rise and Fall Times
2.0
1.5
1.0
0
0
50
100
150
AMBIENT TEMPERATURE (°C)
200
13577-003
0.5
Figure 5. Thermal Derating Curve, Dependence of Safety Limiting Values
with Ambient Temperature per DIN V VDE V 0884-10
Rev. A | Page 11 of 21
Symbol
TA
VDD1, VDD2
Rating
−40°C to +125°C
1.7 V to 5.5 V
1.0 ms
ADuM230D/ADuM230E/ADuM231D/ADuM231E
Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 18. Maximum Continuous Working Voltage1 RI-16 -2
Wide Body Increased Creepage [SOIC_IC] Package
Table 16.
Parameter
Storage Temperature (TST) Range
Ambient Operating Temperature
(TA) Range
Supply Voltages (VDD1, VDD2)
Input Voltages (VIA, VIB, VIC, VE1, VE2,
DISABLE1, DISABLE2)1
Output Voltages (VOA, VOB, VOC)2
Average Output Current per Pin3
Side 1 Output Current (IO1)
Side 2 Output Current (IO2)
Common-Mode Transients4
Rating
−65°C to +150°C
−40°C to +125°C
Parameter
AC Voltage
Bipolar Waveform
Basic Insulation
−0.5 V to +7.0 V
−0.5 V to VDDI + 0.5 V
Reinforced Insulation
Rating
Constraint
849 V peak
50-year minimum
insulation lifetime
Lifetime limited by
package creepage
maximum approved
working voltage per
IEC 60950-1
819 V peak
−0.5 V to VDDO + 0.5 V
−10 mA to +10 mA
−10 mA to +10 mA
−150 kV/μs to +150 kV/μs
Unipolar Waveform
Basic Insulation
Reinforced Insulation
1
VDDI is the input side supply voltage.
VDDO is the output side supply voltage.
3
See Figure 5 for the maximum rated current values for various ambient
temperatures.
4
Refers to the common-mode transients across the insulation barrier.
Common-mode transients exceeding the absolute maximum ratings may
cause latch-up or permanent damage.
1698 V peak
943 V peak
2
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Table 17. Maximum Continuous Working Voltage1 RW-16
Wide Body [SOIC_W] Package
Parameter
AC Voltage
Bipolar Waveform
Basic Insulation
Reinforced Insulation
Unipolar Waveform
Basic Insulation
Reinforced Insulation
DC Voltage
Basic Insulation
Reinforced
Insulation
1
Rating
Constraint
DC Voltage
Basic Insulation
Reinforced Insulation
1
790 V peak
1698 V peak
849 V peak
1118 V peak
559 V peak
579 V peak
Lifetime limited by
package creepage
maximum approved
working voltage per
IEC 60950-1
Lifetime limited by
package creepage
maximum approved
working voltage per
IEC 60950-1
Refers to the continuous voltage magnitude imposed across the isolation
barrier. See the Insulation Lifetime section for more details.
ESD CAUTION
849 V peak
1157 V peak
50-year minimum
insulation lifetime
Lifetime limited by
package creepage
maximum approved
working voltage per
IEC 60950-1
50-year minimum
insulation lifetime
50-year minimum
insulation lifetime
50-year minimum
insulation lifetime
50-year minimum
insulation lifetime
Lifetime limited by
package creepage
maximum approved
working voltage per
IEC 60950-1
Lifetime limited by
package creepage
maximum approved
working voltage per
IEC 60950-1
Refers to the continuous voltage magnitude imposed across the isolation
barrier. See the Insulation Lifetime section for more details.
Rev. A | Page 12 of 21
Data Sheet
ADuM230D/ADuM230E/ADuM231D/ADuM231E
Truth Tables
Table 19. ADuM230D/ADuM231D Truth Table (Positive Logic)
VIx Input1, 2
L
H
X
VDISABLEx Input1, 2
L or NC
L or NC
H
VDDI State2
Powered
Powered
Powered
VDDO State2
Powered
Powered
Powered
Default Low (D0),
VOx Output1, 2, 3
L
H
L
Default High (D1),
VOx Output1, 2, 3
L
H
H
X4
X4
X4
X4
Unpowered
Powered
Powered
Unpowered
L
Indeterminate
H
Indeterminate
Test Conditions/
Comments
Normal operation
Normal operation
Inputs disabled,
fail-safe output
Fail-safe output
1
L means low, H means high, X means don’t care, and NC means not connected.
VIx and VOx refer to the input and output signals of a given channel (A, B, or C). VDISABLEx refers to the input disable signal on the same side as the VIx inputs. VDDI and VDDO
refer to the supply voltages on the input and output sides of the given channel, respectively.
3
D0 refers to the ADuM230D0/ADuM231D0 models, and D1 refers to the ADuM230D1/ADuM231D1 models. See the Ordering Guide section.
4
Input pins (VIx, DISABLEx) on the same side as an unpowered supply must be in a low state to avoid powering the device through its ESD protection circuitry.
2
Table 20. ADuM230E/ADuM231E Truth Table (Positive Logic)
VIx Input1, 2
L
H
X
L
X4
X4
VEx Input1, 2
H or NC
H or NC
L
H or NC
L4
X4
VDDI State2
Powered
Powered
Powered
Unpowered
Unpowered
Powered
VDDO State2
Powered
Powered
Powered
Powered
Powered
Unpowered
Default Low (E0),
VOx Output1, 2, 3
L
H
Z
L
Z
Indeterminate
1
Default High (E1),
VOx Output1, 2, 3
L
H
Z
H
Z
Indeterminate
Test Conditions/
Comments
Normal operation
Normal operation
Outputs disabled
Fail-safe output
Outputs disabled
L means low, H means high, X means don’t care, and NC means not connected, and Z means high impedance.
VIx and VOx refer to the input and output signals of a given channel (A, B, or C). VEx refers to the output enable signal on the same side as the VOx inputs. VDDI and VDDO
refer to the supply voltages on the input and output sides of the given channel, respectively.
3
E0 refers to the ADuM230E0/ADuM231E0 models, and E1 refers to the ADuM230E1/ADuM231E1 models. See the Ordering Guide section.
4
Input pins (VIx, VEx) on the same side as an unpowered supply must be in a low state to avoid powering the device through its ESD protection circuitry.
2
Rev. A | Page 13 of 21
ADuM230D/ADuM230E/ADuM231D/ADuM231E
Data Sheet
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
VDD1 1
16 VDD2
VDD1 1
16 VDD2
GND1 2
15 GND2
GND1 2
15 GND2
14 VOA
VIA 3
14 VOA
VIB 4
ADuM230D
13 VOB
VIB 4
ADuM230E
13 VOB
VIC 5
TOP VIEW
(Not to Scale)
12 VOC
VIC 5
TOP VIEW
(Not to Scale)
12 VOC
NIC 6
11 NIC
NIC 6
11 NIC
DISABLE1 7
10 NIC
NIC 7
10 VE2
9
GND2
NIC = NO INTERNAL CONNECTION.
LEAVE THIS PIN FLOATING.
GND1 8
13577-004
GND1 8
9
GND2
NIC = NO INTERNAL CONNECTION.
LEAVE THIS PIN FLOATING.
13577-005
VIA 3
Figure 7. ADuM230E Pin Configuration
Figure 6. ADuM230D Pin Configuration
Table 21. Pin Function Descriptions
Pin No.1
ADuM230D
ADuM230E
1
1
2, 8
2, 8
3
3
4
4
5
5
6, 10, 11
6, 7, 11
7
Not applicable
Mnemonic
VDD1
GND1
VIA
VIB
VIC
NIC
DISABLE1
9, 15
Not applicable
9, 15
10
GND2
VE2
12
13
14
16
12
13
14
16
VOC
VOB
VOA
VDD2
1
Description
Supply Voltage for Isolator Side 1.
Ground Reference for Isolator Side 1.
Logic Input A.
Logic Input B.
Logic Input C.
No Internal Connection. Leave these pins floating.
Input Disable 1. This pin disables the isolator inputs. Outputs take on the logic state
determined by the fail-safe option shown in the Ordering Guide.
Ground Reference for Isolator Side 2.
Output Enable 2. Active high logic input. When VE2 is high or disconnected, the VOA, VOB,
and VOC outputs are enabled. When VE2 is low, the VOA, VOB, and VOC outputs are disabled
to the high-Z state.
Logic Output C.
Logic Output B.
Logic Output A.
Supply Voltage for Isolator Side 2.
Reference the AN-1109 Application Note for specific layout guidelines.
Rev. A | Page 14 of 21
ADuM230D/ADuM230E/ADuM231D/ADuM231E
VDD1 1
16 VDD2
VDD1 1
16
VDD2
GND1 2
15 GND2
GND1 2
15
GND2
14 VOA
VIA 3
14
VOA
VIA 3
VIB 4
ADuM231D
13 VOB
VIB 4
ADuM231E
13
VOB
VOC 5
TOP VIEW
(Not to Scale)
12 VIC
VOC 5
TOP VIEW
(Not to Scale)
12
VIC
11 NIC
NIC 6
11
NIC
10 DISABLE2
VE1 7
10
VE2
GND1 8
9
GND2
DISABLE1 7
GND1 8
9
GND2
NIC = NO INTERNAL CONNECTION.
LEAVE THIS PIN FLOATING.
13577-104
NIC 6
NIC = NO INTERNAL CONNECTION.
LEAVE THIS PIN FLOATING.
13577-105
Data Sheet
Figure 9. ADuM231E Pin Configuration
Figure 8. ADuM231D Pin Configuration
Table 22. Pin Function Descriptions
Pin No.1
ADuM231D
ADuM231E
1
1
2, 8
2, 8
3
3
4
4
5
5
6, 11
6, 11
7
Not applicable
Mnemonic
VDD1
GND1
VIA
VIB
VOC
NIC
DISABLE1
Not applicable
7
VE1
9, 15
10
9, 15
Not applicable
GND2
DISABLE2
Not applicable
10
VE2
12
13
14
16
12
13
14
16
VIC
VOB
VOA
VDD2
1
Description
Supply Voltage for Isolator Side 1.
Ground Reference for Isolator Side 1.
Logic Input A.
Logic Input B.
Logic Output C.
No Internal Connection. Leave these pins floating.
Input Disable 1. This pin disables the isolator inputs. Outputs take on the logic state
determined by the fail-safe option shown in the Ordering Guide.
Output Enable 1. Active high logic input. When VE1 is high or disconnected, the VOC
output is enabled. When VE1 is low, the VOC output is disabled to the high-Z state.
Ground Reference for Isolator Side 2.
Input Disable 2. This pin disables the isolator inputs. Outputs take on the logic state
determined by the fail-safe option shown in the Ordering Guide.
Output Enable 2. Active high logic input. When VE2 is high or disconnected, the VOA and
VOB outputs are enabled. When VE2 is low, the VOA and VOB outputs are disabled to the
high-Z state.
Logic Input C.
Logic Output B.
Logic Output A.
Supply Voltage for Isolator Side 2.
Reference the AN-1109 Application Note for specific layout guidelines.
Rev. A | Page 15 of 21
ADuM230D/ADuM230E/ADuM231D/ADuM231E
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
16
16
5.0V
3.3V
2.5V
1.8V
12
10
8
6
4
2
40
100
60
80
DATA RATE (Mbps)
120
140
160
Figure 10. ADuM230D/ADuM230E IDD1 Supply Current vs. Data Rate at
Various Voltages
6
4
0
20
40
60
80
100
120
140
160
DATA RATE (Mbps)
Figure 13. ADuM231D/ADuM231E IDD2 Supply Current vs. Data Rate at
Various Voltages
14
PROPAGATION DELAY (tPLH) (ns)
5.0V
3.3V
2.5V
1.8V
14
12
10
8
6
4
12
5.0V
3.3V
2.5V
1.8V
10
8
6
4
20
40
60
80
100
120
140
160
DATA RATE (Mbps)
0
–40
13577-111
0
Figure 11. ADuM230D/ADuM230E IDD2 Supply Current vs. Data Rate at
Various Voltages
–20
0
20
40
60
80
100
120
140
TEMPERATURE (°C)
13577-114
2
2
Figure 14. Propagation Delay (tPLH) vs. Temperature at Various Voltages
14
16
14
PROPAGATION DELAY (tPHL) (ns)
5.0V
3.3V
2.5V
1.8V
12
10
8
6
4
12
5.0V
3.3V
2.5V
1.8V
10
8
6
4
2
2
20
40
60
80
100
DATA RATE (Mbps)
120
140
160
0
–40
13577-112
0
Figure 12. ADuM231D/ADuM231E IDD1 Supply Current vs. Data Rate at
Various Voltages
–20
0
20
40
60
80
TEMPERATURE (°C)
100
120
140
13577-115
IDD2 SUPPLY CURRENT (mA)
8
0
16
IDD1 SUPPLY CURRENT (mA)
10
13577-113
20
13577-110
0
0
12
2
0
0
5.0V
3.3V
2.5V
1.8V
14
IDD2 SUPPLY CURRENT (mA)
IDD1 SUPPLY CURRENT (mA)
14
Figure 15. Propagation Delay( tPHL) vs. Temperature at Various Voltages
Rev. A | Page 16 of 21
Data Sheet
ADuM230D/ADuM230E/ADuM231D/ADuM231E
THEORY OF OPERATION
The ADuM230D/ADuM230E/ADuM231D/ADuM231E use a
high frequency carrier to transmit data across the isolation
barrier using iCoupler chip scale transformer coils separated by
layers of polyimide isolation. Using an on/off keying (OOK)
technique and the differential architecture shown in Figure 16
and Figure 17, the ADuM230D/ADuM230E/ADuM231D/
ADuM231E have very low propagation delay and high speed.
Internal regulators and input/output design techniques allow
logic and supply voltages over a wide range from 1.7 V to 5.5 V,
offering voltage translation of 1.8 V, 2.5 V, 3.3 V, and 5 V logic.
The architecture is designed for high common-mode transient
immunity and high immunity to electrical noise and magnetic
interference. Radiated emissions are minimized with a spread
spectrum OOK carrier and other techniques.
Figure 16 illustrates the waveforms for the models of the
ADuM230D/ADuM230E/ADuM231D/ADuM231E that have
the condition of the fail-safe output state equal to low, where the
carrier waveform is off when the input state is low. If the input
side is off or not operating, the low fail-safe output state (the
ADuM230D0, ADuM231D0, ADuM230E0, and ADuM231E0
models) sets the output to low. For the ADuM230D/ADuM230E/
ADuM231D/ADuM231E models that have a fail-safe output
state of high, Figure 17 illustrates the conditions where the
carrier waveform is off when the input state is high. When the
input side is off or not operating, the high fail-safe output state
(the ADuM230D1, ADuM231D1, ADuM230E0, and
ADuM231E1 models) sets the output to high. See the Ordering
Guide for the model numbers that have the fail-safe output state
of low or the fail-safe output state of high.
REGULATOR
REGULATOR
TRANSMITTER
RECEIVER
VIN
GND1
13577-014
VOUT
GND2
Figure 16. Operational Block Diagram of a Single Channel with a Low Fail-Safe Output State
REGULATOR
REGULATOR
TRANSMITTER
RECEIVER
VIN
GND1
GND2
Figure 17. Operational Block Diagram of a Single Channel with a High Fail-Safe Output State
Rev. A | Page 17 of 21
13577-015
VOUT
ADuM230D/ADuM230E/ADuM231D/ADuM231E
Data Sheet
APPLICATIONS INFORMATION
PCB LAYOUT
JITTER MEASUREMENT
The ADuM230D/ADuM230E/ADuM231D/ADuM231E digital
isolators require no external interface circuitry for the logic
interfaces. Power supply bypassing is strongly recommended at
the input and output supply pins (see Figure 18). Bypass capacitors are most conveniently connected between Pin 1 and Pin 2
for VDD1 and between Pin 15 and Pin 16 for VDD2. The recommended bypass capacitor value is between 0.01 μF and 0.1 μF.
The total lead length between both ends of the capacitor and
the input power supply pin must not exceed 10 mm. Bypassing
between Pin 1 and Pin 8 and between Pin 9 and Pin 16 must
also be considered, unless the ground pair on each package side
is connected close to the package.
Figure 20 shows the eye diagram for the ADuM230D/ADuM230E/
ADuM231D/ADuM231E. The measurement was taken using an
Agilent 81110A pulse pattern generator at 150 Mbps with
pseudorandom bit sequences (PRBS), 2(n − 1), n = 14, for 5 V
supplies. Jitter was measured with the Tektronix Model 5104B
oscilloscope, 1 GHz, 10 GSPS with the DPOJET jitter and eye
diagram analysis tools. The result shows a typical measurement
on the ADuM230D/ADuM230E/ADuM231D/ADuM231E with
630 ps p-p jitter.
4
VOLTAGE (V)
VDD2
GND2
VOA
VOB
VIC/VOC
NIC
DISABLE2/VE2
GND2
13577-010
VDD1
GND1
VIA
VIB
VIC/VOC
NIC
DISABLE1/VE1
GND1
5
NIC = NO INTERNAL CONNECTION. LEAVE THIS PIN FLOATING.
3
2
1
Figure 18. Recommended PCB Layout
See the AN-1109 Application Note for board layout guidelines.
PROPAGATION DELAY RELATED PARAMETERS
Propagation delay is a parameter that describes the time
required for a logic signal to propagate through a component.
The propagation delay to a Logic 0 output may differ from the
propagation delay to a Logic 1 output.
INPUT (VIx)
50%
OUTPUT (VOx)
tPHL
13577-011
tPLH
50%
Figure 19. Propagation Delay Parameters
Pulse width distortion is the maximum difference between these
two propagation delay values and is an indication of how
accurately the timing of the input signal is preserved.
Channel matching is the maximum amount the propagation
delay differs between channels within a single ADuM230D/
ADuM230E/ADuM231D/ADuM231E component.
Propagation delay skew is the maximum amount the propagation
delay differs between multiple ADuM230D/ADuM230E/
ADuM231D/ADuM231E components operating under the
same conditions.
0
–10
–5
0
TIME (ns)
5
10
13577-012
In applications involving high common-mode transients, ensure
that board coupling across the isolation barrier is minimized.
Furthermore, design the board layout such that any coupling
that does occur equally affects all pins on a given component
side. Failure to ensure this can cause voltage differentials between
pins exceeding the Absolute Maximum Ratings of the device,
thereby leading to latch-up or permanent damage.
Figure 20. Eye Diagram
INSULATION LIFETIME
All insulation structures eventually break down when subjected
to voltage stress over a sufficiently long period. The rate of
insulation degradation is dependent on the characteristics of the
voltage waveform applied across the insulation as well as on the
materials and material interfaces.
The two types of insulation degradation of primary interest are
breakdown along surfaces exposed to the air and insulation wear
out. Surface breakdown is the phenomenon of surface tracking
and the primary determinant of surface creepage requirements
in system level standards. Insulation wear out is the phenomenon
where charge injection or displacement currents inside the
insulation material cause long-term insulation degradation.
Surface Tracking
Surface tracking is addressed in electrical safety standards by
setting a minimum surface creepage based on the working
voltage, the environmental conditions, and the properties of the
insulation material. Safety agencies perform characterization
testing on the surface insulation of components, which allows
the components to be categorized in different material groups.
Lower material group ratings are more resistant to surface
tracking and, therefore, can provide adequate lifetime with
smaller creepage. The minimum creepage for a given working
voltage and material group is in each system level standard and
is based on the total rms voltage across the isolation, pollution
Rev. A | Page 18 of 21
Data Sheet
ADuM230D/ADuM230E/ADuM231D/ADuM231E
creepage, clearance, and lifetime of a device, see Figure 21 and
the following equations.
degree, and material group. The material group and creepage
for the ADuM230D/ADuM230E/ADuM231D/ADuM231E
isolators are presented in Table 9.
The working voltage across the barrier from Equation 1 is
Insulation Wear Out
The ratings in certification documents are usually based on
60 Hz sinusoidal stress because this reflects isolation from line
voltage. However, many practical applications have combinations
of 60 Hz ac and dc across the barrier as shown in Equation 1.
Because only the ac portion of the stress causes wear out, the
equation can be rearranged to solve for the ac rms voltage, as is
shown in Equation 2. For insulation wear out with the polyimide
materials used in these products, the ac rms voltage determines
the product lifetime.
VRMS  VAC RMS2  VDC2
(1)
V AC RMS  VRMS 2  VDC 2
(2)
or
where:
VRMS is the total rms working voltage.
VAC RMS is the time varying portion of the working voltage.
VDC is the dc offset of the working voltage.
VRMS  2402  4002
VRMS = 466 V
This VRMS value is the working voltage used together with the
material group and pollution degree when looking up the
creepage required by a system standard.
To determine if the lifetime is adequate, obtain the time varying
portion of the working voltage. To obtain the ac rms voltage,
use Equation 2.
V AC RMS  VRMS 2  VDC 2
VAC RMS  4662  4002
VAC RMS = 240 V rms
In this case, the ac rms voltage is simply the line voltage of
240 V rms. This calculation is more relevant when the waveform is
not sinusoidal. The value is compared to the limits for working
voltage in Table 17 for the expected lifetime, less than a 60 Hz
sine wave, and it is well within the limit for a 50-year service life.
Note that the dc working voltage limit in Table 17 is set by the
creepage of the package as specified in IEC 60664-1. This value
can differ for specific system level standards.
Calculation and Use of Parameters Example
VAC RMS
VPEAK
VRMS
VDC
TIME
The following example frequently arises in power conversion
applications. Assume that the line voltage on one side of the
isolation is 240 V ac rms and a 400 V dc bus voltage is present
on the other side of the isolation barrier. The isolator material is
polyimide. To establish the critical voltages in determining the
Rev. A | Page 19 of 21
Figure 21. Critical Voltage Example
13577-013
Testing and modeling have shown that the primary driver of
long-term degradation is displacement current in the polyimide
insulation causing incremental damage. The stress on the insulation can be broken down into broad categories, such as dc
stress, which causes very little wear out because there is no
displacement current, and an ac component time varying
voltage stress, which causes wear out.
VRMS  VAC RMS2  VDC2
ISOLATION VOLTAGE
The lifetime of insulation caused by wear out is determined by
the insulation thickness and material properties, and the voltage
stress applied. It is important to verify that the product lifetime
is adequate at the application working voltage. The working
voltage supported by an isolator for wear out may not be the
same as the working voltage supported for tracking. The
working voltage applicable to tracking is specified in most
standards.
ADuM230D/ADuM230E/ADuM231D/ADuM231E
Data Sheet
OUTLINE DIMENSIONS
10.50 (0.4134)
10.10 (0.3976)
9
16
7.60 (0.2992)
7.40 (0.2913)
1
8
1.27 (0.0500)
BSC
0.75 (0.0295)
45°
0.25 (0.0098)
2.65 (0.1043)
2.35 (0.0925)
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
10.65 (0.4193)
10.00 (0.3937)
SEATING
PLANE
0.51 (0.0201)
0.31 (0.0122)
8°
0°
1.27 (0.0500)
0.40 (0.0157)
0.33 (0.0130)
0.20 (0.0079)
03-27-2007-B
COMPLIANT TO JEDEC STANDARDS MS-013-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 22. 16-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-16)
Dimensions shown in millimeters and (inches)
12.85
12.75
12.65
1.93 REF
16
9
7.60
7.50
7.40
10.51
10.31
10.11
8
PIN 1
MARK
2.64
2.54
2.44
2.44
2.24
0.30
0.20
0.10
COPLANARITY
0.1
0.71
0.50
0.31
0.25 BSC
GAGE
PLANE
45°
SEATING
PLANE
1.27 BSC
1.01
0.76
0.51
0.46
0.36
COMPLIANT TO JEDEC STANDARDS MS-013-AC
Figure 23. 16-Lead Standard Small Outline Package, with Increased Creepage [SOIC_IC]
Wide Body
(RI-16-2)
Dimensions shown in millimeters
Rev. A | Page 20 of 21
0.32
0.23
8°
0°
11-15-2011-A
1
Data Sheet
ADuM230D/ADuM230E/ADuM231D/ADuM231E
ORDERING GUIDE
Model1
ADuM230D1BRWZ
ADuM230D1BRWZ-RL
ADuM230D0BRWZ
ADuM230D0BRWZ-RL
ADuM230E1BRWZ
ADuM230E1BRWZ-RL
ADuM230E0BRWZ
ADuM230E0BRWZ-RL
ADuM230D1BRIZ
ADuM230D1BRIZ-RL
ADuM230D0BRIZ
ADuM230D0BRIZ-RL
ADuM230E1BRIZ
ADuM230E1BRIZ-RL
ADuM230E0BRIZ
ADuM230E0BRIZ-RL
ADuM231D1BRWZ
ADuM231D1BRWZ-RL
ADuM231D0BRWZ
ADuM231D0BRWZ-RL
ADuM231E1BRWZ
ADuM231E1BRWZ-RL
ADuM231E0BRWZ
ADuM231E0BRWZ-RL
ADuM231D1BRIZ
ADuM231D1BRIZ-RL
ADuM231D0BRIZ
ADuM231D0BRIZ-RL
ADuM231E1BRIZ
ADuM231E1BRIZ-RL
ADuM231E0BRIZ
ADuM231E0BRIZ-RL
1
Temperature
Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
No. of
Inputs,
VDD1
Side
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
No. of
Inputs,
VDD2
Side
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Withstand
Voltage
Rating
(kV rms)
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
Fail-Safe
Output
State
High
High
Low
Low
High
High
Low
Low
High
High
Low
Low
High
High
Low
Low
High
High
Low
Low
High
High
Low
Low
High
High
Low
Low
High
High
Low
Low
Z = RoHS Compliant Part.
©2015–2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D13577-0-4/16(A)
Rev. A | Page 21 of 21
Input
Disable
Yes
Yes
Yes
Yes
No
No
No
No
Yes
Yes
Yes
Yes
No
No
No
No
Yes
Yes
Yes
Yes
No
No
No
No
Yes
Yes
Yes
Yes
No
No
No
No
Output
Enable
No
No
No
No
Yes
Yes
Yes
Yes
No
No
No
No
Yes
Yes
Yes
Yes
No
No
No
No
Yes
Yes
Yes
Yes
No
No
No
No
Yes
Yes
Yes
Yes
Package
Description
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_IC
16-Lead SOIC_IC
16-Lead SOIC_IC
16-Lead SOIC_IC
16-Lead SOIC_IC
16-Lead SOIC_IC
16-Lead SOIC_IC
16-Lead SOIC_IC
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_IC
16-Lead SOIC_IC
16-Lead SOIC_IC
16-Lead SOIC_IC
16-Lead SOIC_IC
16-Lead SOIC_IC
16-Lead SOIC_IC
16-Lead SOIC_IC
Package
Option
RW-16
RW-16
RW-16
RW-16
RW-16
RW-16
RW-16
RW-16
RI-16-2
RI-16-2
RI-16-2
RI-16-2
RI-16-2
RI-16-2
RI-16-2
RI-16-2
RW-16
RW-16
RW-16
RW-16
RW-16
RW-16
RW-16
RW-16
RI-16-2
RI-16-2
RI-16-2
RI-16-2
RI-16-2
RI-16-2
RI-16-2
RI-16-2
Similar pages