ON NLVHC4851ADR2G Analog multiplexers/ demultiplexer Datasheet

MC74HC4851A,
MC74HC4852A
Analog Multiplexers/
Demultiplexers with
Injection Current Effect
Control
www.onsemi.com
Automotive Customized
These devices are pin compatible to standard HC405x and
MC1405xB analog mux/demux devices, but feature injection current
effect control. This makes them especially suited for usage in
automotive applications where voltages in excess of normal logic
voltage are common.
The injection current effect control allows signals at disabled analog
input channels to exceed the supply voltage range without affecting
the signal of the enabled analog channel. This eliminates the need for
external diode/resistor networks typically used to keep the analog
channel signals within the supply voltage range.
The devices utilize low power silicon gate CMOS technology.
The Channel Select and Enable inputs are compatible with standard
CMOS outputs.
•
TSSOP−16
DT SUFFIX
CASE 948F
1
QFN16
MN SUFFIX
CASE 485AW
16
16
HC4851A
AWLYWWG
HC485xAG
AWLYWW
• Injection Current Cross−Coupling Less than 1 mV/mA (See
•
•
•
•
•
SOIC−16 WIDE
DW SUFFIX
CASE 751G
MARKING DIAGRAMS
Features
Figure 10)
Pin Compatible to HC405X and MC1405XB Devices
Power Supply Range (VCC − GND) = 2.0 to 6.0 V
In Compliance With the Requirements of JEDEC Standard No. 7 A
Chip Complexity: 154 FETs or 36 Equivalent Gates
NLV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These Devices are Pb−Free, Halogen Free and are RoHS Compliant
SOIC−16
D SUFFIX
CASE 751B
1
SOIC−16
1
SOIC−16 WIDE
16
HC48
5xA
ALYWG
G
1
TSSOP−16
x
A
WL, L
YY, Y
WW, W
G or G
4851
ALYWG
G
QFN16*
*V4851 marking used for
NLV74HC4851AMN1TWG
= 1 or 2
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 12 of this data sheet.
This document contains information on some products that are still under development.
ON Semiconductor reserves the right to change or discontinue these products without
notice.
© Semiconductor Components Industries, LLC, 2016
October, 2016 − Rev. 21
1
Publication Order Number:
MC74HC4851A/D
MC74HC4851A, MC74HC4852A
13
X0
14
X1
15
X2
ANALOG
12
MULTIPLEXER/
INPUTS/ X3
DEMULTIPLEXER
OUTPUTS X4 1
5
X5
2
X6
4
X7
11
A
CHANNEL
10
B
SELECT
9
INPUTS
C
6
ENABLE
PIN 16 = VCC
PIN 8 = GND
FUNCTION TABLE − MC74HC4851A
Control Inputs
3
COMMON
X
OUTPUT/
INPUT
Enable
C
L
L
L
L
L
L
L
L
H
L
L
L
L
H
H
H
H
X
Select
B
A
L
L
H
H
L
L
H
H
X
ON Channels
X0
X1
X2
X3
X4
X5
X6
X7
NONE
L
H
L
H
L
H
L
H
X
Figure 1. MC74HC4851A Logic Diagram
Single−Pole, 8−Position Plus Common Off
VCC
X2
X1
X0
X3
A
B
C
16
15
14
13
12
11
10
9
1
2
3
4
5
X4
X6
X
X7
X5
6
7
X4 VCC
1 16
X6
2
15 X2
X
3
14 X1
X7
4
X5
5
12 X3
ENABLE
6
11 A
N
C
7
8
GND
Enable NC
Figure 2. MC74HC4851A 16−Lead Pinout (Top View)
13 X0
GND
10 B
8
9
C
GND
Figure 3. MC74HC4851A QFN Pinout
FUNCTION TABLE − MC74HC4852A
Control Inputs
Select
Enable
B
A
ON Channels
L
L
L
L
H
L
L
H
H
X
L
H
L
H
X
Y0
Y1
Y2
Y3
12
ANALOG
INPUTS/OUTPUTS
CHANNEL‐SELECT
INPUTS
X0
14
X1
15
X2
11
X3
Y0
Y1
Y2
Y3
A
B
ENABLE
X SWITCH
13
X
COMMON
OUTPUTS/INPUTS
1
Y SWITCH
3
Y
4
10
9
NONE
X = Don’t Care
5
2
X0
X1
X2
X3
PIN 16 = VCC
PIN 8 = GND
VCC
X2
X1
X
X0
X3
A
B
16
15
14
13
12
11
10
9
6
7
8
GND
6
Figure 4. MC74HC4852A Logic Diagram
Double−Pole, 4−Position Plus Common Off
1
2
3
4
5
Y0
Y2
Y
Y3
Y1
Enable NC
Figure 5. MC74HC4852A 16−Lead Pinout (Top View)
www.onsemi.com
2
MC74HC4851A, MC74HC4852A
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
MAXIMUM RATINGS
Symbol
Value
Unit
VCC
Positive DC Supply Voltage
(Referenced to GND)
–0.5 to +7.0
V
Vin
DC Input Voltage (Any Pin)
(Referenced to GND)
–0.5 to VCC + 0.5
V
±25
mA
500
450
mW
–65 to +150
°C
I
Parameter
DC Current, Into or Out of Any Pin
PD
Power Dissipation in Still Air,
SOIC Package†
TSSOP Package†
Tstg
Storage Temperature Range
TL
Lead Temperature, 1 mm from Case for 10 Seconds
SOIC or TSSOP Package
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance circuit. For proper operation, Vin and
Vout should be constrained to the
range GND v (Vin or Vout) v VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or VCC).
Unused outputs must be left open.
°C
260
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of
these limits are exceeded, device functionality should not be assumed, damage may occur and
reliability may be affected.
†Derating: SOIC Package: –7 mW/°C from 65° to 125°C
TSSOP Package: −6.1 mW/°C from 65° to 125°C
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Min
Max
Unit
VCC
Positive DC Supply Voltage
(Referenced to GND)
2.0
6.0
V
Vin
DC Input Voltage (Any Pin)
(Referenced to GND)
GND
VCC
V
VIO*
Static or Dynamic Voltage Across Switch
0.0
1.2
V
TA
Operating Temperature Range, All Package Types
–55
+125
°C
tr, tf
Input Rise/Fall Time
(Channel Select or Enable Inputs)
0
0
0
1000
500
400
ns
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
*For voltage drops across switch greater than 1.2 V (switch on), excessive VCC current may be drawn; i.e., the current out of the switch may
contain both VCC and switch input components. The reliability of the device will be unaffected unless the Maximum Ratings are exceeded.
DC CHARACTERISTICS — Digital Section (Voltages Referenced to GND) VEE = GND, Except Where Noted
Symbol
Parameter
Condition
Guaranteed Limit
VCC
V
−55 to 25°C
≤85°C
≤125°C
Unit
VIH
Minimum High−Level Input Voltage,
Channel−Select or Enable Inputs
Ron = Per Spec
2.0
3.0
4.5
6.0
1.50
2.10
3.15
4.20
1.50
2.10
3.15
4.20
1.50
2.10
3.15
4.20
V
VIL
Maximum Low−Level Input Voltage,
Channel−Select or Enable Inputs
Ron = Per Spec
2.0
3.0
4.5
6.0
0.50
0.90
1.35
1.80
0.50
0.90
1.35
1.80
0.50
0.90
1.35
1.80
V
Iin
Maximum Input Leakage Current on Digital Pins
(Enable/A/B/C)
Vin = VCC or GND
6.0
±0.1
±1.0
±1.0
mA
ICC
Maximum Quiescent Supply Current
(per Package)
Vin(digital) = VCC or GND
Vin(analog) = GND
6.0
2
20
40
mA
www.onsemi.com
3
MC74HC4851A, MC74HC4852A
DC CHARACTERISTICS — Analog Section
Guaranteed Limit
Symbol
Ron
DRon
Ioff
Ion
≤85°C
≤125°C
Unit
Condition
VCC
−55 to 25°C
Maximum “ON” Resistance
Vin = VIL or VIH; VIS = VCC to
GND (Note 1); IS ≤ 2.0 mA
(Note 2)
2.0
3.0
4.5
6.0
1700
1100
550
400
1750
1200
650
500
1800
1300
750
600
W
Delta “ON” Resistance
Vin = VIL or VIH; VIS = VCC/2
(Note 1); IS ≤ 2.0 mA (Note 2)
2.0
3.0
4.5
6.0
300
160
80
60
400
200
100
80
500
240
120
100
W
Maximum Off−Channel Leakage Current,
Any One Channel
Common Channel
Vin = VCC or GND
6.0
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
Maximum On−Channel Leakage
Channel−to−Channel
Vin = VCC or GND
6.0
±0.1
±0.1
±0.1
Parameter
mA
mA
1. VIS is the input voltage of an analog I/O pin.
2. IS is the currebnt flowing in or out of analog I/O pin.
AC CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns)
VCC
−55 to 25°C
≤85°C
≤125°C
Unit
Maximum Propagation Delay, Analog Input to Analog Output
2.0
3.0
4.5
6.0
160
80
40
30
180
90
45
35
200
100
50
40
ns
Maximum Propagation Delay, Enable or Channel−Select to Analog Output
2.0
3.0
4.5
6.0
260
160
80
78
280
180
90
80
300
200
100
80
ns
10
35
40
10
35
40
10
35
40
pF
Parameter
Symbol
tPHL,
tPLH
tPHL,
tPHZ,PZH
tPLH,
tPLZ,PZL
Cin
Maximum Input Capacitance
(All Switches Off)
(All Switches Off)
CPD
Power Dissipation Capacitance
Digital Pins
Any Single Analog Pin
Common Analog Pin
Typical
5.0
20
pF
INJECTION CURRENT COUPLING SPECIFICATIONS (VCC = 5V, TA = −55°C to +125°C)
Symbol
VDout
Parameter
Condition
Maximum Shift of Output Voltage of Enabled Analog Channel
Iin* ≤ 1 mA, RS ≤ 3,9 kW
Iin* ≤ 10 mA, RS ≤ 3,9 kW
Iin* ≤ 1 mA, RS ≤ 20 kW
Iin* ≤ 10 mA, RS ≤ 20 kW
* Iin = Total current injected into all disabled channels.
www.onsemi.com
4
Typ
Max
Unit
0.1
1.0
0.5
5.0
1.0
5.0
2.0
20
mV
MC74HC4851A, MC74HC4852A
1100
1000
R on , ON RESISTANCE (OHMS)
900
-55°C
800
+25°C
700
+125°C
600
500
400
300
200
R on , ON RESISTANCE (OHMS)
1100
1000
100
800
700
600
500
+25°C
300
+125°C
200
0.4
0.8
1.2
1.6
0
0.0
2.0
0.6
1.2
1.8
2.4
Vin, INPUT VOLTAGE (VOLTS), REFERENCED TO GND
Vin, INPUT VOLTAGE (VOLTS), REFERENCED TO GND
Figure 6. Typical On Resistance VCC = 2V
Figure 7. Typical On Resistance VCC = 3V
660
440
600
400
540
360
480
420
360
-55°C
300
+25°C
240
+125°C
180
-55°C
280
160
120
40
2.7
3.6
0
0.0
4.5
+125°C
200
80
1.8
+25°C
240
60
0.9
1.2
2.4
3.6
4.8
Vin, INPUT VOLTAGE (VOLTS), REFERENCED TO GND
Vin, INPUT VOLTAGE (VOLTS), REFERENCED TO GND
Figure 8. Typical On Resistance VCC = 4.5V
Figure 9. Typical On Resistance VCC = 6V
www.onsemi.com
5
3.0
320
120
0
0.0
-55°C
400
100
R on , ON RESISTANCE (OHMS)
R on , ON RESISTANCE (OHMS)
0
0.0
900
6.0
MC74HC4851A, MC74HC4852A
External DC P.S.
VCC = 5 V
Vin2 / Iin2 meas. here.
Current Source
HP4155C
Smu #2
Vin1 = 4.9 V (Smu3)
Iin1 measure here
Vm1 connected here.
4
16
13
3
X7
RS
X0
X
Vout
Vm2 connected here.
6
NOTES: Rs = 3.9 KW or 20 KW.
NOTES: Vm1 & Vm2 are internal
NOTES:
HP4155C Voltmeters.
8
GND or VSS
Figure 10. Injection Current Coupling Specification
www.onsemi.com
6
MC74HC4851A, MC74HC4852A
5V
6V
5V
VCC
VCC
HC4051A
Sensor
Microcontroller
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8
(8x Identical Circuitry)
Common Out
A/D - Input
Figure 11. Actual Technology
Requires 32 passive components and one extra 6V regulator
to suppress injection current into a standard HC4051 multiplexer
5V
VCC
VCC
HC4851A
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8
Sensor
(8x Identical Circuitry)
Common Out
Microcontroller
A/D - Input
Figure 12. MC74HC4851A Solution
Solution by applying the HC4851A multiplexer
www.onsemi.com
7
MC74HC4851A, MC74HC4852A
PLOTTER
VCC
PROGRAMMABLE
POWER
SUPPLY
MINI COMPUTER
DC ANALYZER
16
VEE
VCC
OFF
-
+
VCC
VCC
A
COMMON O/I
OFF
NC
DEVICE
UNDER TEST
ANALOG IN
VIH
COMMON OUT
6
8
GND
Figure 14. Maximum Off Channel Leakage Current,
Any One Channel, Test Set−Up
Figure 13. On Resistance Test
Set−Up
VCC
16
VEE
ANALOG I/O
VCC
A
VEE
16
A
OFF
VCC
OFF
VIH
VCC
VCC
ON
COMMON O/I
VCC
N/C
ANALOG I/O
VIL
6
COMMON O/I
OFF
6
8
8
Figure 15. Maximum Off Channel Leakage Current,
Common Channel, Test Set−Up
Figure 16. Maximum On Channel Leakage Current,
Channel to Channel, Test Set−Up
VCC
VCC
16
VCC
CHANNEL
SELECT
ON/OFF
50%
OFF/ON
GND
tPLH
ANALOG
OUT
COMMON O/I
ANALOG I/O
TEST
POINT
CL*
tPHL
6
50%
8
CHANNEL SELECT
*Includes all probe and jig capacitance
Figure 17. Propagation Delays, Channel Select
to Analog Out
Figure 18. Propagation Delay, Test Set−Up Channel
Select to Analog Out
www.onsemi.com
8
MC74HC4851A, MC74HC4852A
VCC
16
VCC
ANALOG
IN
COMMON O/I
ANALOG I/O
ON
50%
TEST
POINT
CL*
GND
tPLH
tPHL
ANALOG
OUT
6
8
50%
*Includes all probe and jig capacitance
Figure 19. Propagation Delays, Analog In
to Analog Out
tf
tr
tPZL
ANALOG
OUT
2
GND
tPLZ
16
HIGH
IMPEDANCE
10%
VCC
VCC
1
TEST
POINT
ON/OFF
CL*
VOL
tPHZ
ENABLE
VOH
90%
10kW
ANALOG I/O
2
50%
tPZH
POSITION 1 WHEN TESTING tPHZ AND tPZH
POSITION 2 WHEN TESTING tPLZ AND tPZL
1
VCC
90%
50%
10%
ENABLE
ANALOG
OUT
Figure 20. Propagation Delay, Test Set−Up
Analog In to Analog Out
50%
6
8
HIGH
IMPEDANCE
Figure 21. Propagation Delays, Enable to
Analog Out
Figure 22. Propagation Delay, Test Set−Up
Enable to Analog Out
VCC
VCC
A
16
COMMON O/I
NC
ANALOG I/O
VCC
6
8
11
CHANNEL SELECT
Figure 23. Power Dissipation Capacitance,
Test Set−Up
www.onsemi.com
9
MC74HC4851A, MC74HC4852A
Gate = VCC
(Disabled)
Disabled Analog Mux Input
Vin > VCC + 0.7V
P+
Common Analog Output
Vout > VCC
P+
+
+
+
N - Substrate (on VCC potential)
Figure 24. Diagram of Bipolar Coupling Mechanism
Appears if Vin exceeds VCC, driving injection current into the substrate
A
B
C
ENABLE
11
10
INJECTION
CURRENT
CONTROL
13
INJECTION
CURRENT
CONTROL
14
INJECTION
CURRENT
CONTROL
15
INJECTION
CURRENT
CONTROL
12
INJECTION
CURRENT
CONTROL
1
INJECTION
CURRENT
CONTROL
5
INJECTION
CURRENT
CONTROL
2
INJECTION
CURRENT
CONTROL
4
INJECTION
CURRENT
CONTROL
3
X0
X1
X2
X3
9
6
Figure 25. Function Diagram, HC4851A
www.onsemi.com
10
X4
X5
X6
X7
X
MC74HC4851A, MC74HC4852A
A
B
ENABLE
10
9
INJECTION
CURRENT
CONTROL
13
INJECTION
CURRENT
CONTROL
14
INJECTION
CURRENT
CONTROL
15
13
INJECTION
CURRENT
CONTROL
12
INJECTION
CURRENT
CONTROL
3
INJECTION
CURRENT
CONTROL
1
INJECTION
CURRENT
CONTROL
5
INJECTION
CURRENT
CONTROL
2
INJECTION
CURRENT
CONTROL
4
INJECTION
CURRENT
CONTROL
3
X0
X1
X2
X3
X
Y0
Y1
6
Figure 26. Function Diagram, HC4852A
www.onsemi.com
11
Y2
Y3
Y
MC74HC4851A, MC74HC4852A
ORDERING INFORMATION
Device
Package
MC74HC4851ADG
MC74HC4851ADR2G
48 Units / Rail
SOIC−16
(Pb−Free)
NLVHC4851ADR2G*
MC74HC4851ADTR2G
NLVHC4851ADTR2G*
MC74HC4851ADWR2G
NLVHC4851ADWR2G*
TSSOP−16
(Pb−Free)
2500 Units / Tape & Reel
SOIC−16 WIDE
(Pb−Free)
1000 Units / Tape & Reel
3000 Units / Tape & Reel
QFN16
(Pb−Free)
MC74HC4852ADG
MC74HC4852ADR2G
NLVHC4852ADTR2G*
3000 Units / Tape & Reel
48 Units / Rail
SOIC−16
(Pb−Free)
NLV74HC4852ADR2G*
MC74HC4852ADTR2G
2500 Units / Tape & Reel
2500 Units / Tape & Reel
NLV74HC4851AMNTWG*#
NLV74HC4851AMN1TWG*#
(In Development)
Shipping†
2500 Units / Tape & Reel
2500 Units / Tape & Reel
TSSOP−16
(Pb−Free)
2500 Units / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable.
#MN suffix is with pull−back lead, MN1 is without pull−back lead. Refer to ’Detail A’ of case outline on page 16.
www.onsemi.com
12
MC74HC4851A, MC74HC4852A
PACKAGE DIMENSIONS
TSSOP−16
DT SUFFIX
CASE 948F
ISSUE B
16X K REF
0.10 (0.004)
0.15 (0.006) T U
M
T U
S
V
S
S
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
ÇÇÇ
ÉÉÉ
K
K1
2X
L/2
16
9
J1
B
−U−
L
SECTION N−N
J
PIN 1
IDENT.
N
0.25 (0.010)
8
1
M
0.15 (0.006) T U
S
A
−V−
NOTES:
1.
DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2.
CONTROLLING DIMENSION: MILLIMETER.
3.
DIMENSION A DOES NOT INCLUDE MOLD FLASH.
PROTRUSIONS OR GATE BURRS. MOLD FLASH OR
GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER
SIDE.
4.
DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER
SIDE.
5.
DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL CONDITION.
6.
TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7.
DIMENSION A AND B ARE TO BE DETERMINED AT
DATUM PLANE -W-.
N
F
DETAIL E
−W−
C
0.10 (0.004)
−T− SEATING
PLANE
H
D
DETAIL E
G
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
MILLIMETERS
MIN
MAX
4.90
5.10
4.30
4.50
−−−
1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.18
0.28
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0_
8_
SOLDERING FOOTPRINT*
7.06
1
0.65
PITCH
16X
0.36
16X
1.26
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
13
INCHES
MIN
MAX
0.193 0.200
0.169 0.177
−−− 0.047
0.002 0.006
0.020 0.030
0.026 BSC
0.007
0.011
0.004 0.008
0.004 0.006
0.007 0.012
0.007 0.010
0.252 BSC
0_
8_
MC74HC4851A, MC74HC4852A
PACKAGE DIMENSIONS
SOIC−16 WB
DW SUFFIX
CASE 751G−03
ISSUE D
A
D
9
1
8
16X
M
T A
h X 45 _
MILLIMETERS
DIM MIN
MAX
A
2.35
2.65
A1 0.10
0.25
B
0.35
0.49
C
0.23
0.32
D 10.15 10.45
E
7.40
7.60
e
1.27 BSC
H 10.05 10.55
h
0.25
0.75
L
0.50
0.90
q
0_
7_
S
B
S
L
A
0.25
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M, 1994.
3. DIMENSIONS D AND E DO NOT INLCUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
5. DIMENSION B DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.13 TOTAL IN
EXCESS OF THE B DIMENSION AT MAXIMUM
MATERIAL CONDITION.
B
B
14X
e
A1
H
E
0.25
8X
M
B
M
16
q
C
T
SEATING
PLANE
SOLDERING FOOTPRINT*
16X
0.58
11.00
1
16X
1.27
PITCH
1.62
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
14
MC74HC4851A, MC74HC4852A
PACKAGE DIMENSIONS
SOIC−16
D SUFFIX
CASE 751B−05
ISSUE K
−A−
16
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL CONDITION.
9
−B−
1
P
8 PL
0.25 (0.010)
8
B
M
S
G
R
K
F
X 45 _
C
−T−
SEATING
PLANE
J
M
D
DIM
A
B
C
D
F
G
J
K
M
P
R
16 PL
0.25 (0.010)
M
T B
S
A
S
SOLDERING FOOTPRINT*
8X
6.40
16X
1
1.12
16
16X
0.58
1.27
PITCH
8
9
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
15
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0_
7_
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0_
7_
0.229
0.244
0.010
0.019
MC74HC4851A, MC74HC4852A
PACKAGE DIMENSIONS
QFN16, 2.5x3.5, 0.5P
CASE 485AW
ISSUE O
D
PIN ONE
REFERENCE
A
B
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
2X
L1
DETAIL A
E
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
L1
ÇÇÇ
ÉÉÉ
TOP VIEW
MOLD CMPD
DETAIL B
ALTERNATE
CONSTRUCTIONS
A
DETAIL B
(A3)
0.10 C
16X
ALTERNATE TERMINAL
CONSTRUCTIONS
EXPOSED Cu
0.15 C
L
L
0.15 C
2X
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSIONS b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30 MM FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.20 REF
0.20
0.30
2.50 BSC
0.85
1.15
3.50 BSC
1.85
2.15
0.50 BSC
0.20
--0.35
0.45
--0.15
A1
0.08 C
NOTE 4
C
SIDE VIEW
SEATING
PLANE
SOLDERING FOOTPRINT*
3.80
0.15 C A B
D2
16X
L
8
2.10
K
0.50
PITCH
0.15 C A B
10
DETAIL A
2.80 1.10
E2
1
16X
2
15
1
b
0.10 C A B
0.05 C
16X
0.60
NOTE 3
16X
PACKAGE
OUTLINE
0.30
DIMENSIONS: MILLIMETERS
e
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
e/2
BOTTOM VIEW
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
◊
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
16
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC74HC4851A/D
Similar pages