Wall JFCW48S15-10GH 10 watt dc/dc power converter Datasheet

JFCW10 SERIES
10 Watt DC/DC Power Converters
Rev B
FEATURES
Size:
1.00 x 1.00 x 0.39 inches
(25.4 x 25.4 x 9.9 mm)
• High Efficiency up to 91%
• Built-in EN55022 Class B Filter
• Remote On/Off Control
• 10 Watts Maximum Output Power
• 4:1 Ultra Wide Input Voltage Ranges
• Short Circuit, Over Voltage, Over Load, & Under-Voltage Protection
• Six-Sided Continuous Shielding
• Wide Operating Temperature Range: -40°C to +85°C
• Ultra Low Quiescent Current
• Compliant to RoHS EU Directive 2011/65/EU
• No Minimum Load Requirements
• UL60950-1, EN60950-1, & IEC60950-1 Safety Approvals
• Single and Dual Outputs
• CE Mark meets 2006/95/EC, 2011/95/EC, and 2004/108/EC
• Fixed Switching Frequency
• Optional Heatsink Available (Suffix “HC”)
DESCRIPTION
Options:
• Negative Logic Remote ON/OFF
• Without Trim pin
• Without CTRL Pin
• Heatsink
The JFCW10 series of DC/DC power converters provides 10 Watts of output power in an industry standard 1.00” x
1.00” x 0.39” package and footprint. This series has single and dual output models with 4:1 ultra wide input voltage
ranges of 9-36VDC and 18-75VDC. Some features include high efficiency up to 91%, 1600VDC I/O isolation, six-sided
shielding, and remote on/off control. These converters are also protected against short circuit, over voltage, over
load, and under-voltage. All models are RoHS compliant and have UL60950-1, EN60950-1, and IEC60950-1 safety
approvals. This series is best suited for use in wireless networks, telecom/datacom, industry control systems,
measurement equipment, and semiconductor equipment.
MODEL SELECTION TABLE
Model Number
JFCW24S33-10
JFCW24S05-10
JFCW24S12-10
JFCW24S15-10
JFCW24S24-10
JFCW48S33-10
JFCW48S05-10
JFCW48S12-10
JFCW48S15-10
JFCW48S24-10
Model Number
JFCW24D05-10
JFCW24D12-10
JFCW24D15-10
JFCW48D05-10
JFCW48D12-10
JFCW48D15-10
Input Voltage Range
24 VDC
(9 – 36 VDC)
48 VDC
(18 – 75 VDC)
Input Voltage Range
24 VDC
(9 – 36 VDC)
48 VDC
(18 – 75 VDC)
SINGLE OUTPUT MODELS
Output
Voltage
3.3 VDC
5 VDC
12 VDC
15 VDC
24 VDC
3.3 VDC
5 VDC
12 VDC
15 VDC
24 VDC
Output Current
Min Load
Max Load
0mA
3000mA
0mA
2000mA
0mA
830mA
0mA
670mA
0mA
416mA
0mA
3000mA
0mA
2000mA
0mA
830mA
0mA
670mA
0mA
416mA
Output
Ripple & Noise
40mVp-p
40mVp-p
60mVp-p
60mVp-p
60mVp-p
40mVp-p
40mVp-p
60mVp-p
60mVp-p
60mVp-p
No Load
Input Current
6mA
6mA
6mA
6mA
6mA
4mA
4mA
4mA
4mA
4mA
Output
Power
9.9W
10W
10W
10W
10W
9.9W
10W
10W
10W
10W
Output
Voltage
±5 VDC
±12 VDC
±15 VDC
±5 VDC
±12 VDC
±15 VDC
Output Current
Min Load
Max Load
0mA
±1000mA
0mA
±416mA
0mA
±333mA
0mA
±1000mA
0mA
±416mA
0mA
±333mA
Output
Ripple & Noise
40mVp-p
60mVp-p
60mVp-p
40mVp-p
60mVp-p
60mVp-p
No Load
Input Current
6mA
6mA
6mA
4mA
4mA
4mA
Output
Power
10W
10W
10W
10W
10W
10W
DUAL OUTPUT MODELS
Efficiency
85%
87%
90%
91%
90%
85%
87%
90%
90%
90%
Efficiency
87%
89%
89%
87%
89%
89%
Maximum
Capacitive Load
3500µF
2500µF
430µF
350µF
125µF
3500µF
2500µF
430µF
350µF
125µF
Maximum
Capacitive Load
±1440µF
±250µF
±180µF
±1440µF
±250µF
±180µF
NOTES
1. Trimming allows the user to increase or decrease the output voltage set point of the module. This is accomplished by connecting an external resistor
between the Trim pin and either the +Vout pin or the –Vout pin.
2. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor suggested is Nippon chemi-con KY
series, 220µF/100V.
3. The JFCW10 series standard modules meet EN55022 Class A without external components and meets Class B with external components. See page 4 for more
details.
4. Both positive logic and negative logic remote on/off control is available. Positive logic remote on/off comes standard; for negative logic remote on/off add
the suffix “R” to the model number (Ex: JFCW24S05-10R).
5. There are several different options available for this series. Please see the “Model Number Setup” on page 5 for all options and ordering information.
6. Optional heatsink is available. Please call factory for more information.
CAUTION: This power module is not internally fused. An input line fuse must always be used.
*Due to advances in technology, specifications subject to change without notice.
10/31/2014
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797
website: www.wallindustries.com • e-mail: [email protected]
Page 1 of 5
JFCW10 SERIES
10 Watt DC/DC Power Converters
Rev B
TECHNICAL SPECIFICATIONS: JFCW10 SERIES
All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted.
We reserve the right to change specifications based on technological advances.
SPECIFICATION
TEST CONDITIONS
INPUT SPECIFICATIONS
Input Voltage Range
Start-Up Voltage
Shutdown Voltage
Input Surge Voltage (1sec, max.)
Input Reflected Ripple Current
Input Current
OUTPUT SPECIFICATIONS
Output Voltage
Voltage Accuracy
Line Regulation
24VDC nominal input models
48VDC nominal input models
24VDC nominal input models
48VDC nominal input models
24VDC nominal input models
48VDC nominal input models
24VDC nominal input models
48VDC nominal input models
No load to full load
Load Regulation
10% load to 90% load
Single Output Models
Output Power
Rated
With Trim up 10%
With Trim up 20%
Ripple & Noise (20MHz BW)
Transient Response Recovery Time
Start-Up Time
Temperature Coefficient
PROTECTION
Short Circuit Protection
Over Load Protection
9
18
24
48
36
75
9
18
30
See Table
Single Output Models
Dual Output Models
Single Output Models
Dual Output Models
Single Output Models
Dual Output Models
3.3V & 12V Output Models
Others
-1.0
-0.2
-0.5
-0.2
-1.0
-0.1
-0.8
-5.0
-10
-10
See Table
+1.0
+0.2
+0.5
+0.2
+1.0
+0.1
+0.8
+5.0
+10
+20
10
11
12
See Table
0
3.3V & 5V Output Models
12V & 15V Output Models
24V Output Models
±5V Output Models
±12V & ±15V Output Models
Nom. input and constant resistive load
Power Up
Remote ON/OFF
-0.02
% of rated full load at nominal input
Zener diode clamp
GENERAL SPECIFICATIONS
Efficiency
Switching Frequency
Nominal input voltage and full load
3.3V & 5V Output Models
Isolation Voltage
1 minute
Isolation Resistance
Isolation Capacitance
500VDC
3.3V Output Models
5V Output Models
12V Output Models
15V Output Models
24V Output Models
Input to Output
Input to Case
Output to Case
Unit
VDC
VDC
VDC
50
100
Minimum input and constant resistive load
With 10µF/25V X7R 1206 MLCC
With 10µF/25V X7R 1206 MLCC
With 1µF/50V X7R 1206 MLCC
With 10µF/25V X7R 1206 MLCC for each output
With 10µF/25V X7R 1206 MLCC for each output
25% load step change
Over Voltage Protection
10/31/2014
Max
8
16
Asymmetrical load 25% / 100% FL
Voltage Adjustability (See Note 1)
Output Current
Minimum Load
Maximum Capacitive Load
Typ
No Load
Low line to high line at full load
Cross Regulation (Dual Output Models)
Min
VDC
mAp-p
%
%
%
%
%
%
W
%
See Table
40
60
60
40
60
250
30
30
+0.02
mVp-p
µs
ms
%/°C
continuous, automatic recovery
150
%
3.7
5.4
6.3
7.4
13.5
19.6
VDC
18.3
22.0
29.1
32.5
297
1600
1000
1000
1
See Table
330
363
VDC
1500
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797
website: www.wallindustries.com • e-mail: [email protected]
kHz
GΩ
pF
Page 2 of 5
JFCW10 SERIES
10 Watt DC/DC Power Converters
Rev B
TECHNICAL SPECIFICATIONS: JFCW10 SERIES
All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted.
We reserve the right to change specifications based on technological advances.
SPECIFICATION
TEST CONDITIONS
REMOTE ON/OFF (See Note 4)
Positive Logic (standard)
The CTRL pin is referenced to –Input pin
Negative Logic (optional)
The CTRL pin is referenced to –Input pin
Input Current of Remote Control Pin
Remote OFF State Input Current
ENVIRONMENTAL SPECIFICATIONS
Operating Ambient Temperature
Maximum Case Temperature
Storage Temperature
Nominal Vin
Nominal Vin
Thermal Impedance (See Note 6)
Natural Convection
Relative Humidity
Thermal Shock
Vibration
MTBF
PHYSICAL SPECIFICATIONS
Weight
Dimensions (L x W x H)
Case Material
Base Material
Potting Material
Shielding
SAFETY & EMC CHARACTERISTICS
Safety Approvals
EMI (See Note 3)
Min
DC/DC ON
DC/DC OFF
DC/DC ON
DC/DC OFF
Typ
Max
Unit
Open or 3V < Vr < 15 VDC
Short or 0V < Vr < 1.2 VDC
Short or 0V <Vr < 1.2 VDC
Open or 3V < Vr < 15 VDC
-0.5
1.0
2.5
With derating
-40
Without Heatsink
With Heatsink
-55
16.18
15.13
5
+85
+105
+125
°C
°C
°C
°C/W
95
MIL-STD-810F
MIL-STD-810F
3,376,000 hours
MIL-HDBK-217F Ta=25°C, full load
mA
mA
% RH
0.58oz (16.5g)
1.00x1.00x0.39 inch (25.4x25.4x9.9 mm)
Copper
FR4 PCB
Silicon (UL94-V0)
Six-sided
EN55022
ESD
EN61000-4-2
Radiated Immunity
Fast Transient (See Note 2)
Surge (See Note 2)
Conducted Immunity
EN61000-4-3
EN61000-4-4
EN61000-4-5
EN61000-4-6
UL60950-1, IEC60950-1, EN60950-1
Class A, Class B
Air ±8kV
Contact ±6kV
10 V/m
±2kV
±1kV
3 Vrms
Perf. Criteria A
Perf. Criteria A
Perf. Criteria A
Perf. Criteria A
Perf. Criteria A
MECHANICAL DRAWING
PIN CONNECTIONS
PRODUCT OPTIONS
PIN
SINGLE
DUAL
OPTION
1
+INPUT
+INPUT
Positive Logic Remote On/Off
SUFFIX
2
-INPUT
-INPUT
Negative Logic Remote On/Off
R
3
CTRL
CTRL
Without CTRL Pin
D
4
+OUTPUT
+OUTPUT
Without CTRL and TRIM Pins
G
5
TRIM
COMMON
Positive Logic without TRIM Pin
F
6
-OUTPUT
-OUTPUT
Negative Logic without TRIM Pin
RF
Heatsink
HC
None
EXTERNAL OUTPUT TRIMMING
Output can be externally trimmed by using the
method shown below
NOTES
1. Unit: inches (mm)
2. Tolerance: X.XX±0.02 (X.X±0.5)
X.XXX±0.01 (X.XX±0.25)
3. Pin Pitch Tolerance: ±0.01 (±0.25)
4. Pin Dimension Tolerance: ±0.004 (±0.1)
5. All dimensions are for reference only
10/31/2014
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797
website: www.wallindustries.com • e-mail: [email protected]
Page 3 of 5
JFCW10 SERIES
10 Watt DC/DC Power Converters
Rev B
DERATING CURVES
JFCW48S05-10 Derating Curve
JFCW48S05-10 Derating Curve with Heatsink
EFFICIENCY CURVES
JFCW48S05-10 Efficiency vs Input Voltage
JFCW48S05-10 Efficiency vs Output Load
EMI CONSIDERATIONS
Recommended External EMI Filter for EN55022 Class B
Single Output
Model
10/31/2014
Dual Output
C1
Model
C1
JFCW24SXX-10
6.8µF/50V 1812 MLCC
JFCW24DXX-10
6.8µF/50V 1812 MLCC
JFCW48SXX-10
4.7µF/100V 1812 MLCC
JFCW48DXX-10
4.7µF/100V 1812 MLCC
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797
website: www.wallindustries.com • e-mail: [email protected]
Page 4 of 5
JFCW10 SERIES
10 Watt DC/DC Power Converters
Rev B
MODEL NUMBER SETUP
JFCW
24
S
05
Series Name
Input Voltage
Output Quantity
24: 9-36 VDC
S: Single Output
48: 18-75 VDC
D: Dual Output
-
10
R
H
Ouptut Voltage
Output Power
Remote ON/OFF, CTRL, and TRIM Pins
Heatsink
33: 3.3 VDC
10: 10 Watts
None: Positive Logic Remote On/Off
05: 5 VDC
R: Negative Logic Remote On/Off
12: 12 VDC
D: Without CTRL Pin
15: 15 VDC
G: Without CTRL and TRIM Pins
24: 24 VDC
F: Positive Logic without TRIM Pin
05: ±5 VDC
RF: Negative Logic without TRIM Pin
None: No Heatsink
HC: Heatsink
12: ±12 VDC
15: ±15 VDC
COMPANY INFORMATION
Wall Industries, Inc. has created custom and modified units for over 50 years. Our in-house research and development engineers will provide a solution
that exceeds your performance requirements on-time and on budget. Our ISO9001-2008 certification is just one example of our commitment to
producing a high quality, well-documented product for our customers.
Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a reputation for working closely with its customers to
ensure each solution meets or exceeds form, fit and function requirements. We will continue to provide ongoing support for your project above and
beyond the design and production phases. Give us a call today to discuss your future projects.
Contact Wall Industries for further information:
Phone:
Toll Free:
Fax:
E-mail:
Web:
Address:
10/31/2014
(603)778-2300
(888)597-9255
(603)778-9797
[email protected]
www.wallindustries.com
37 Industrial Drive
Exeter, NH 03833
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797
website: www.wallindustries.com • e-mail: [email protected]
Page 5 of 5
Similar pages