TI1 LP8556SQE-E08 High-efficiency led backlight driver for tablet Datasheet

Sample &
Buy
Product
Folder
Technical
Documents
Support &
Community
Tools &
Software
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
LP8556 High-Efficiency LED Backlight Driver for Tablets
1 Features
3 Description
•
The LP8556 device is a white-LED driver featuring an
asynchronous boost converter and six high precision
current sinks that can be controlled by a PWM signal
or an I2C master.
1
•
•
•
•
•
•
•
•
•
•
High-Efficiency DC–DC Boost Converter With
Integrated 0.19-Ω Power MOSFET and Three
Switching Frequency Options: 312 kHz, 625 kHz,
and 1250 kHz
2.7-V to 36-V Boost Switch Input Voltage Range
Supports Multi-Cell Li-Ion Batteries
(2.7-V to 20-V VDD Input Range)
7-V to 43-V Boost Switch Output Voltage Range
Supports as Few as 3 WLEDs in Series Per
Channel and as Many as 12
Configurable Channel Count (1 to 6)
Up to 50 mA Per Channel
PWM and / or I2C Brightness Control
Phase-Shift PWM Mode Reduces Audible Noise
Adaptive Dimming for Higher LED Drive Optical
Efficiency
Programmable Edge-Rate Control and Spread
Spectrum Scheme Minimize Switching Noise and
Improve EMI Performance
LED Fault (Short and Open) Detection, UVLO,
TSD, OCP, and OVP (Up to 6 Threshold Options)
Available in Tiny 20-Pin, 0.4-mm Pitch DSBGA
Package and 24-Pin, 0.5-mm Pitch WQFN
Package
2 Applications
The boost converter uses adaptive output voltage
control for setting the optimal LED driver voltages as
low as 7 V and as high as 43 V. This feature
minimizes the power consumption by adjusting the
output voltage to the lowest sufficient level under all
conditions. The converter can operate at three
switching frequencies: 312 kHz, 625 kHz, and 1250
kHz, which can be set with an external resistor or
pre-configured via EPROM. Programmable slew rate
control and spread spectrum scheme minimize
switching noise and improve EMI performance.
LED current sinks can be set with the PWM dimming
resolution of up to 15 bits. Proprietary adaptive
dimming mode allows higher system power saving. In
addition, phase shifted LED PWM dimming allows
reduced audible noise and smaller boost output
capacitors.
The LP8556 device has a full set of fault-protection
features that ensure robust operation of the device
and external components. The set consists of input
undervoltage lockout (UVLO), thermal shutdown
(TSD), overcurrent protection (OCP), up to 6 levels of
overvoltage protection (OVP), LED open and short
detection.
The LP8556 device operates over the ambient
temperature range of –30°C to +85°C. It is available
in space-saving 20-pin DSBGA and 24-pad WQFN
packages.
LED Backlights for Tablet LCDs
Simplified Schematic
7V ± 43V
2.7V - 20V
L1
D1
1.1 ” 9OUT / VIN ” 15
CIN
COUT
VDD
EN / VDDIO
Device Information(1)
VOUT
VIN
1.62V ± 3.6V
SW
EN / VDDIO
VBOOST
CVLDO
VLDO
PART NUMBER
LP8556
PACKAGE
BODY SIZE
DSBGA (20)
2.401 mm × 1.74 mm (MAX)
WQFN (24)
4.00 mm × 4.00 mm (NOM)
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
LED1
RFSET
FSET
LED2
RISET
ISET
LP8556
LED3
Optional
LED4
LED5
PWM
MCU
LED6
SDA
SCL
GNDs
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Device Options.......................................................
Pin Configuration and Functions .........................
Specifications.........................................................
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
7.11
8
1
1
1
2
3
4
6
Absolute Maximum Ratings ...................................... 6
ESD Ratings.............................................................. 6
Recommended Operating Conditions....................... 6
Thermal Information .................................................. 6
Electrical Characteristics........................................... 7
Electrical Characteristics — Boost Converter .......... 8
Electrical Characteristics — LED Driver ................... 9
Electrical Characteristics — PWM Interface ............. 9
Electrical Characteristics — Logic Interface .......... 10
I2C Serial Bus Timing Parameters (SDA, SCL) .... 10
Typical Characteristics .......................................... 11
Detailed Description ............................................ 12
8.1
8.2
8.3
8.4
8.5
8.6
9
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
Programming...........................................................
Register Maps .........................................................
12
12
13
28
28
32
Application and Implementation ........................ 45
9.1 Application Information............................................ 45
9.2 Typical Application ................................................. 47
10 Power Supply Recommendations ..................... 51
11 Layout................................................................... 51
11.1 Layout Guidelines ................................................. 51
11.2 Layout Examples................................................... 52
12 Device and Documentation Support ................. 54
12.1
12.2
12.3
12.4
Trademarks ...........................................................
Community Resources..........................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
54
54
54
54
13 Mechanical, Packaging, and Orderable
Information ........................................................... 54
4 Revision History
Changes from Revision H (December 2014) to Revision I
Page
•
Changed "25 mA" to "23 mA" - E00, E08 and E09 SQ rows, E09, E11 TME rows ............................................................... 3
•
Changed Handing Ratings table to ESD Ratings .................................................................................................................. 6
•
Added updated Thermal Information ..................................................................................................................................... 6
•
Changed "8" to "10" in PWMres row ...................................................................................................................................... 9
•
Changed subtracted 1 from bit value of all Table 4 "ƒPWM [Hz] (Resolution)" entries ......................................................... 20
•
Changed subtracted 1 from bit value of all Table 5 "ƒPWM [Hz] (Resolution)" entries except 2402 .................................... 21
•
Changed subtracted 1 from bit value of all Table 11 "ƒPWM [Hz] (Resolution)" entries ....................................................... 45
•
Changed "via EPROM" in Table 13 title to "With an External Resistor" ............................................................................. 46
•
Changed subtracted 1 from bit values of all Table 13 "ƒPWM [Hz] (Resolution)" entries except 2402 ................................. 46
Changes from Revision G (November 2013) to Revision H
•
Page
Added Pin Configuration and Functions section, Handling Ratings table, Feature Description section, Device
Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout
section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information
section ................................................................................................................................................................................... 1
Changes from Revision E (August 2013) to Revision G
Page
•
Changed Description of "1=" for OCP row in Fault table, STATUS Register Section.......................................................... 34
•
Changed A7h values for E02, E03, E04, E06, E07, E09, E11 DSGBA EPROM Bit Explanations tables ........................... 36
•
Deleted E00, E01, E08, E10, E12, E13 columns and A8H row from 3 EPROM Bit Explanations table.............................. 36
•
Changed values for E00, E08, E09 WQFN EPROM Settings table..................................................................................... 37
2
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
5 Device Options
ORDERABLE DEVICE (1)
PACKAGE
TYPE
DEVICE OPTION
LP8556SQ-E00/NOPB
LP8556SQE-E00/NOPB
LP8556SQX-E00/NOPB
LP8556SQ-E08/NOPB
LP8556SQE-E08/NOPB
LP8556SQX-E08/NOPB
WQFN
BOOST OUTPUT
VOLTAGE
RANGE
“PWM Only” – Recommended for
systems without an I2C master.
23 mA
16 V to 34.5 V
6
25 mA
16 V to 30 V
5
20 mA
16 V to 34.5 V
6
20 mA
16 V to 25 V
Can be
programmed
to any
available.
25 mA
Can be
programmed to
any available.
5
25 mA
16 V to 39 V
4
20 mA
12.88 V to 30 V
6
23 mA
16 V to 34.5 V
3
23 mA
7 V to 21 V
4
6
“PWM and I2C” - Recommended for
systems with an I2C master.
LP8556TME-E02/NOPB
LP8556TMX-E02/NOPB
LP8556TME-E03/NOPB
LP8556TMX-E03/NOPB
“PWM Only” – Recommended for
systems without an I2C master.
LP8556TME-E04/NOPB
LP8556TMX-E04/NOPB
DSBGA
“Non-programmed” – This option is
for evaluation purposes only.
LP8556TME-E06/NOPB
LP8556TMX-E06/NOPB
LP8556TME-E07/NOPB
LP8556TMX-E07/NOPB
“PWM Only” – Recommended for
systems without an I2C master.
LP8556TME-E09/NOPB
LP8556TMX-E09/NOPB
LP8556TME-E11/NOPB
LP8556TMX-E11/NOPB
(1)
MAXIMUM LED
CURRENT
5
LP8556SQ-E09/NOPB
LP8556SQE-E09/NOPB
LP8556SQX-E09/NOPB
LP8556TME-E05/NOPB
LP8556TMX-E05/NOPB
LED
CHANNEL
COUNT
2
“PWM and I C” - Recommended for
systems with an I2C master.
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
3
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
6 Pin Configuration and Functions
YFQ Package
20-Pin DSBGA
Top View
YFQ Package
20-Pin DSBGA
Bottom View
1
2
3
4
4
3
2
1
A
SW
GND
SW
SDA
SCL
SCL
SDA
GND
SW
SW
A
B
SW
GND
SW
PWM
EN
VDDIO
EN
VDDIO
PWM
GND
SW
SW
B
C
VDD
VBOOST
FSET
LED3
LED3
FSET
VBOOST
VDD
C
D
VLDO
ISET
GND
LED2
LED2
GND
ISET
VLDO
D
E
LED6
LED5
LED4
LED1
LED1
LED4
LED5
LED6
E
4
SCL
1
SDA
SW
2
GND_SW
SW
3
GND_SW
GND_SW
4
PIN 1 ID
SW
GND_SW
5
PIN 1 ID
SW
SDA
6
1
2
3
4
5
6
24
GND
GND
24
7
EN / VDDIO
8
23
ISET
ISET
23
8
NC
PWM
9
22
VDD
VDD
22
9
PWM
GND
10
21
FSET
GND
11
20
VBOOST
LED1
12
19
VLDO
GND
LED5
LED6
VLDO
19
12
LED1
Submit Documentation Feedback
18
17
16
15
14
13
LED2
18
GND
GND
17
GND
11
LED3
16
10
20
LED4
15
21
LED5
14
FSET
VBOOST
LED6
13
LED4
7
LED3
NC
LED2
EN/VDDIO
RTW Package
24-Pin WQFN
Bottom View
SCL
RTW Package
24-Pin WQFN
Top View
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
Pin Functions
PIN
NAME
TYPE (1)
DESCRIPTION
DSBGA
WQFN
A1, B1
1, 2
SW
A
A connection to the drain terminal of the integrated power MOSFET.
A2, B2
3, 4
GND_SW
G
A connection to the source terminal of the integrated power MOSFET.
A3
5
SDA
I/O
I2C data input/output pin
A4
6
SCL
I
I2C clock input pin
B3
9
PWM
I
PWM dimming input. Supply a 75-Hz to 25-kHz PWM signal to control
dimming. This pin must be connected to GND if unused.
B4
7
EN / VDDIO
P
Dual-purpose pin serving both as a chip enable and as a power supply
reference for PWM, SDA, and SCL inputs. Drive this pin with a logic
gate capable of sourcing a minimum of 1 mA.
C1
22
VDD
P
Device power supply pin. Provide 2.7-V to 20-V supply to this pin. This
pin is an input of the internal LDO regulator. The output of the internal
LDO is what powers the device.
C2
20
VBOOST
A
Boost converter output pin. The internal feedback (FB) and overvoltage
protection (OVP) circuitry monitors the voltage on this pin. Connect the
converter output capacitor bank close to this pin.
C3
21
FSET
A
A connection for setting the boost frequency and PWM output dimming
frequency by using an external resistor. Connect a resistor, RFSET,
between this pin and the ground reference (see Table 5). This pin may
be left floating if PWM_FSET_EN = 0 AND BOOST_FSET_EN = 0
(see Table 10).
C4
14
LED3
A
LED driver - current sink terminal. If unused, it may be left floating.
D1
19
VLDO
P
Internal LDO output pin. Connect a capacitor, CVLDO, between this pin
and the ground reference.
D2
23
ISET
A
A connection for the LED current set resistor. Connect a resistor,
RISET, between this pin and the ground reference. This pin may be left
floating if ISET_EN = 0 (see Table 10).
D3
10, 11, 15, 24,
DAP
GND
I
Ground pin.
D4
13
LED2
A
LED driver - current sink pin. If unused, it may be left floating.
E1
18
LED6
A
LED driver - current sink pin. If unused, it may be left floating.
E2
17
LED5
A
LED driver - current sink pin. If unused, it may be left floating.
E3
16
LED4
A
LED driver - current sink pin. If unused, it may be left floating.
E4
12
LED1
A
LED driver - current sink pin. If unused, it may be left floating.
—
8
NC
—
No Connect pin.
(1)
A: Analog Pin, G: Ground Pin, P: Power Pin, I: Digital Input Pin, I/O: Digital Input/Output Pin
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
5
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
MIN
MAX
VDD
–0.3
24
Voltage on Logic Pins (SCL, SDA, PWM)
–0.3
6
Voltage on Analog Pins (VLDO, EN / VDDIO)
–0.3
6
Voltage on Analog Pins (FSET, ISET)
–0.3
VLDO + 0.3
V (LED1...LED6, SW, VBOOST)
–0.3
UNIT
V
50
Junction Temperature (TJ-MAX) (3)
125
°C
Maximum Lead Temperature (Soldering)
260
°C
150
°C
Storage temperature, Tstg
(1)
(2)
(3)
–65
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability, see the
Electrical Characteristics tables.
If Military/Aerospace specified devices are required, contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be de-rated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP =
125°C), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the
part/package in the application (RθJA), as given by the following equation: TA-MAX = TJ-MAX-OP – (RθJA × PD-MAX).
7.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±2000
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
±500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) (1)
VDD
EN / VDDIO
MIN
MAX
2.7
20
V
1.62
3.6
V
V (LED1...LED6, SW, VBOOST)
UNIT
0
48
V
Junction temperature, TJ
–30
125
°C
Ambient temperature, TA
–30
85
°C
(1)
All voltages are with respect to the potential at the GND pins.
7.4 Thermal Information
LP8556
THERMAL METRIC
(1)
YFQ (DSBGA)
RTW (WQFN)
20 PINS
24 PINS
UNIT
66.2
35.0
°C/W
RθJA
Junction-to-ambient thermal resistance
RθJC(top)
Junction-to-case (top) thermal resistance
0.5
32.2
°C/W
RθJB
Junction-to-board thermal resistance
15.1
13.7
°C/W
ψJT
Junction-to-top characterization parameter
1.9
0.3
°C/W
ψJB
Junction-to-board characterization parameter
15.0
13.8
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
n/a
3.3
°C/W
(1)
6
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report (SPRA953).
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
7.5 Electrical Characteristics
Unless otherwise specified: VDD = 12 V, EN / VDDIO = 1.8 V, TA = 25°C (1) (2)
PARAMETER
VDDIO
Supply voltage for digital I/Os
VDD
Input voltage for the internal LDO
Standby supply current
IDD
Normal mode supply current
fOSC
Internal oscillator frequency
accuracy
VLDO
LDO output voltage
TTSD
Thermal shutdown threshold
TTSD_hyst
Thermal shutdown hysteresis
(1)
(2)
(3)
TEST CONDITIONS
MIN
TYP
MAX
1.62
3.6
V
2.7
20
V
1.6
μA
EN / VDDIO = 0 V, LDO disabled,
–30°C ≤ TA ≤ 85°C
LDO enabled, boost disabled
0.9
1.5
LDO enabled, boost enabled, no load
2.2
3.65
–4%
–30°C ≤ TA ≤ 85°C
–7%
VDD ≥ 3.1 V
2.95
2.7 V ≤ VDD < 3.1 V
See (3)
UNIT
mA
4%
7%
3.05
3.15
VDD – 0.05
V
150
°C
20
°C
All voltages are with respect to the potential at the GND pins.
Minimum (MIN) and Maximum (MAX) limits are verified by design, test, or statistical analysis. Typical numbers are for information only.
Verified by design and not tested in production.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
7
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
7.6 Electrical Characteristics — Boost Converter
over operating free-air temperature range (unless otherwise noted) (1)
PARAMETER
TEST CONDITIONS
RDS_ON
Switch ON resistance
ISW = 0.5A
VBOOST_MIN
Boost minimum output
voltage
VBOOST_RANGE = 0
VBOOST_RANGE = 1
VBOOST_MAX
ILOAD_MAX
VOUT/VIN
Boost maximum output
voltage
Maximum continuous output
load current
V
=0
=0
=0
=0
19
24.0
28.0
32
21
25
30
34
22
27
32
37
V
VBOOST_MAX = 010,
VBOOST_MAX = 011,
VBOOST_MAX = 100,
VBOOST_MAX = 101,
VBOOST_MAX = 110,
VBOOST_MAX = 111,
VBOOST_RANGE
VBOOST_RANGE
VBOOST_RANGE
VBOOST_RANGE
VBOOST_RANGE
VBOOST_RANGE
=1
=1
=1
=1
=1
=1
17.9
22.8
27.8
32.7
37.2
41.8
21
25
30
34.5
39
43
23.1
27.2
31.5
36.6
40.8
44.2
V
VIN = 3 V, VOUT = 18 V
220
VIN = 3 V, VOUT = 24 V
160
VIN = 3 V, VOUT = 30 V
120
Switching frequency
VOVP
Overvoltage protection
voltage
VBOOST_RANGE = 1
VUVLO
VIN undervoltage lockout
threshold
VUVLO_hyst
VUVLO hysteresis
VUVLO[rising]
VUVLO[falling]
tPULSE
Switch minimum pulse width
No load
mA
15
12
312
625
1250
kHz
VBOOST + 1.6
V
2.5
5.2
V
UVLO_EN = 1
UVLO_TH = 0, falling
UVLO_TH = 1, falling
See
UVLO_TH = 0
50
UVLO_TH = 1
100
mV
50
(3)
ns
8
IBOOST_LIM_2X = 0
SW pin current limit
Ω
7
16
fSW = 1250 kHz
Start-up time
UNIT
0.19
fSW = 625 kHz
Conversion ratio (2)
MAX
VBOOST_RANGE
VBOOST_RANGE
VBOOST_RANGE
VBOOST_RANGE
fSW
ISW_LIM
TYP
VBOOST_MAX = 100,
VBOOST_MAX = 101,
VBOOST_MAX = 110,
VBOOST_MAX = 111,
BOOST_FREQ = 00
BOOST_FREQ = 01
BOOST_FREQ = 10
tSTARTUP
MIN
(4)
IBOOST_LIM_2X = 1
IBOOST_LIM
IBOOST_LIM
IBOOST_LIM
IBOOST_LIM
= 00
= 01
= 10
= 11
IBOOST_LIM = 00
IBOOST_LIM = 01
IBOOST_LIM = 10
0.66
0.88
1.12
1.35
0.9
1.2
1.5
1.8
ms
1.16
1.40
1.73
2.07
A
1.6
2.1
2.6
A
ΔVSW /
toff_on
EN_DRV3 = 0 AND EN_DRV2 = 0
SW pin slew rate during OFF
EN_DRV3 = 0 AND EN_DRV2 = 1
to ON transition
EN_DRV3 = 1 AND EN_DRV2 = 1
3.7
5.3
7.5
V/ns
ΔVSW /
ton_off
SW pin slew rate during ON
to OFF transition
EN_DRV3 = 0 AND EN_DRV2 = 0
EN_DRV3 = 0 AND EN_DRV2 = 1
EN_DRV3 = 1 AND EN_DRV2 = 1
1.9
4.4
4.8
V/ns
ΔtON / tSW
Peak-to-peak switch ON
time deviation to SW period
ratio (spread spectrum
feature)
SSCLK_EN = 1
1%
(1)
(2)
(3)
(4)
8
Minimum (MIN) and Maximum (MAX) limits are verified by design, test, or statistical analysis. Typical numbers are for information only.
Verified by design and not tested in production.
Start-up time is measured from the moment boost is activated until the VBOOST crosses 90% of its target value.
1.8 A is the maximum ISW_LIM supported with the DSBGA package. For applications requiring the ISW_LIM to be greater than 1.8 A and
up to 2.6 A, WQFN package should be considered.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
7.7 Electrical Characteristics — LED Driver
over operating free-air temperature range (unless otherwise noted) (1)
PARAMETER
TEST CONDITIONS
MIN
MAX
0.1
1
ILED_LEAKAGE
Leakage current
ILED_MAX
Maximum sink current
LED1...LED6
Output current set to 23 mA
–3%
1%
3%
ILED
LED current accuracy (2)
Output current set to 23 mA,
–30°C ≤ TA ≤ 85°C
–4%
1%
4%
IMATCH
Matching
Output current set to 23 mA
PWMDUTY
fLED
(2)
(3)
(4)
LED PWM output pulse duty
cycle (3)
PWM output frequency
VSAT
(1)
Outputs LED1...LED6, VOUT = 48 V
TYP
Saturation voltage
(4)
50
UNIT
µA
mA
0.5%
100 Hz < fPWM ≤ 200 Hz
0.02%
100%
200 Hz < fPWM ≤ 500 Hz
0.02%
100%
500 Hz < fPWM ≤ 1 kHz
0.02%
100%
1 kHz < fPWM ≤ 2 kHz
0.04%
100%
2 kHz < fPWM ≤ 5 kHz
0.1%
100%
5 kHz < fPWM ≤ 10 kHz
0.2%
100%
10 kHz < fPWM ≤ 20 kHz
0.4%
100%
20 kHz < fPWM ≤ 30 kHz
0.6%
100%
30 kHz < fPWM ≤ 39 kHz
0.8%
100%
PWM_FREQ = 1111
38.5
kHz
Output current set to 23 mA
200
mV
Minimum (MIN) and Maximum (MAX) limits are specified by design, test, or statistical analysis. Typical numbers are not verified, but do
represent the most likely norm.
Output Current Accuracy is the difference between the actual value of the output current and programmed value of this current.
Matching is the maximum difference from the average. For the constant current sinks on the part (OUT1 to OUT6), the following are
determined: the maximum output current (MAX), the minimum output current (MIN), and the average output current of all outputs (AVG).
Two matching numbers are calculated: (MAX-AVG)/AVG and (AVG-MIN/AVG). The largest number of the two (worst case) is
considered the matching figure. The typical specification provided is the most likely norm of the matching figure for all parts. Note that
some manufacturers have different definitions in use.
Verified by design and not tested in production.
Saturation voltage is defined as the voltage when the LED current has dropped 10% from the value measured at 1 V.
7.8 Electrical Characteristics — PWM Interface (1)
PARAMETER
TEST CONDITIONS
(2)
MIN
TYP
25 000
UNIT
fPWM
PWM frequency range
tMIN_ON
Minimum pulse ON time
1
tMIN_OFF
Minimum pulse OFF time
1
tSTARTUP
Turnon delay from standby to
backlight on
PWM input active, VDDIO pin transitions
from 0 V to 1.8 V
10
tSTBY
Turnoff delay
PWM input low time for turnoff
50
ms
PWMRES
PWM input resolution
ƒIN < 9 kHz
10
bits
(1)
(2)
75
MAX
Hz
μs
ms
Minimum (MIN) and Maximum (MAX) limits are specified by design, test, or statistical analysis. Typical numbers are for information only.
Verified by design and not tested in production.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
9
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
7.9 Electrical Characteristics — Logic Interface
PARAMETER
(1)
TEST CONDITIONS
MIN
TYP
MAX
UNIT
LOGIC INPUTS (PWM, SDA, SCL)
VIL
Input low level
–30°C ≤ TA ≤ 85°C
VIH
Input high level
–30°C ≤ TA ≤ 85°C
II
Input current
(VDDIO = 0 V or 3.6 V), (VI = 0 V or 3.6 V),
–30°C ≤ TA ≤ 85°C
0.3 ×
VDDIO
0.7 ×
VDDIO
V
V
–1
1
µA
LOGIC OUTPUTS (SDA)
IOUT = 3 mA (pull-up current)
0.3
VOL
Output low level
IOUT = 3 mA (pull-up current),
–30°C ≤ TA ≤ 85°C
0.3
IL
Output leakage current
VOUT = 5 V, –30°C ≤ TA ≤ 85°C
(1)
0.4
–1
1
V
µA
Minimum (MIN) and Maximum (MAX) limits are specified by design, test, or statistical analysis. Typical numbers are for information only.
7.10 I2C Serial Bus Timing Parameters (SDA, SCL) (1)
MIN
ƒSCL
Clock frequency
1
Hold time (repeated) START condition
2
3
MAX
UNIT
400
kHz
0.6
µs
Clock low time
1.3
µs
Clock high time
600
ns
4
Setup time for a repeated START condition
600
ns
5
Data hold time
50
ns
6
Data set-up time
7
Rise time of SDA and SCL
20 + 0.1Cb
300
ns
8
Fall time of SDA and SCL
15 + 0.1Cb
300
ns
9
Setup time for STOP condition
600
ns
10
Bus-free time between a STOP and a START condition
1.3
µs
Cb
Capacitive load parameter for each bus line load of 1 pF corresponds to 1 ns.
10
(1)
100
ns
200
ns
Verified by design and not tested in production.
Figure 1. I2C-Compatible Timing
10
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
7.11 Typical Characteristics
Unless otherwise specified: VIN = 3.8 V, CVLDO = 10 μF, L1 = 4.7 μH, CIN = 2.2 μF, COUT = 4.7 μF, ƒSW = 1.25 MHz.
VSW
20V/DIV
EN/VDDIO
2V/DIV
IL
500 mA/DIV
VSW
20V/DIV
IOUT
100 mA/DIV
VBOOST
20V/DIV
VBOOSTac
200 mV/DIV
4 ms/DIV
1 Ps/DIV
Figure 2. Steady-State Operation Waveforms
Figure 3. Start-Up Waveforms
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
11
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
8 Detailed Description
8.1 Overview
LP8556 is a white LED driver featuring an asynchronous boost converter and six high-precision current sinks that
can be controlled by a PWM signal or an I2C master.
The boost converter uses adaptive output voltage control for setting the optimal LED driver voltages as high as
43 V. This feature minimizes the power consumption by adjusting the voltage to the lowest sufficient level under
all conditions. The converter can operate at three switching frequencies: 312, 625, and 1250 kHz pre-configured
via EPROM or can be set through an external resistor. Programmable slew rate control and spread spectrum
scheme minimize switching noise and improve EMI performance.
LED current sinks can be set with the PWM dimming resolution of up to 15 bits. Proprietary adaptive dimming
mode allows higher system power saving. In addition, phase shifted LED PWM dimming allows reduced audible
noise and smaller boost output capacitors.
The LP8556 device has a full set of safety features that ensure robust operation of the device and external
components. The set consists of input undervoltage lockout, thermal shutdown, overcurrent protection, up to six
levels of overvoltage protection, LED open, and short detection.
8.2 Functional Block Diagram
VIN
VOUT
VDD
SW
VBOOST
Boost Converter
VLDO
LDO
Reference
Voltage
Thermal
shutdown
Switching
Frequency
312, 625, 1250
kHz
PWM Control
BOOST_FREQ
Oscillator
Headroom
Control
POR
Fault Detection
(Open LED,
OCP, OVP)
LED Current Sinks
LED1
PWM
LED2
PWM Detector
LED3
BRIGHTNESS
EN/VDDIO
LED4
CONTROL
SDA
LED5
2
12
SCL
I C Slave
FSET
BOOST_FREQ
PWM_FREQ
LED6
ISET
EPROM
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
8.3 Feature Description
8.3.1 Boost Converter
8.3.1.1 Boost Converter Operation
The LP8556 boost DC-DC converter generates a 7-V to approximately 43-V of boost output voltage from a 2.7-V
to 36-V boost input voltage. The boost output voltage minimum, maximum value and range can be set digitally by
pre-configuring EPROM memory (VBOOST_RANGE, VBOOST, and VBOOST_MAX fields).
The converter is a magnetic switching PWM mode DC-DC boost converter with a current limit. It uses CPM
(current programmed mode) control, where the inductor current is measured and controlled with the feedback.
During start-up, the soft-start function reduces the peak inductor current. The LP8556 has an internal 20-MHz
oscillator which is used for clocking the boost. Figure 4 shows the boost block diagram.
VBOOST
SW
Startup
OVP
Light
Load
R
R
R
S
R
R
Spread
Spectrum
OCP
VREF
Edge Rate
Control
+
gm
+
VFB
Osc/
ramp
+
-
6
Active Load
Figure 4. LP8556 Boost Converter Block Diagram
8.3.1.2 Setting Boost Switching Frequency
The LP8556 boost converter switching frequency can be set either by an external resistor (BOOST_FSET_EN =
1 selection), RFSET, or by pre-configuring EPROM memory with the choice of boost frequency (BOOST_FREQ
field). Table 1 summarizes setting of the switching frequency. Note that the RFSET is shared for setting the PWM
dimming frequency in addition to setting the boost switching frequency. Setting the boost switching frequency
and PWM dimming frequency using an external resistor is separately shown in Table 5.
Table 1. Configuring Boost Switching Frequency via EPROM
RFSET [Ω]
BOOST_FSET_EN
BOOST_FREQ[1:0]
ƒSW [kHz]
don't care
0
00
312
don't care
0
01
625
don't care
0
10
1250
don't care
0
11
undefined
1
don't care
See (1)
See
(1)
(1)
See Table 5.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
13
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
8.3.1.3 Output Voltage Control
The LP8556 device supports two modes of controlling the boost output voltage: Adaptive Boost Voltage Control
(see Adaptive Control) and Manual Boost Output Control (see Manual Control).
8.3.1.3.1 Adaptive Control
LP8556 supports a mode of output voltage control called Adaptive Boost Control mode. In this mode, the voltage
at the LED pins is periodically monitored by the control loop and adaptively adjusted to the optimum value based
on the comparator thresholds set using LED DRIVER_HEADROOM, LED_COMP_HYST, BOOST_STEP_UP,
BOOST_STEP_DOWN fields in the EPROM. Settings under LED DRIVER_HEADROOM along with
LED_COMP_HYST fields determine optimum boost voltage for a given condition. Boost voltage is raised if the
voltage measured at any of the LED strings falls below the threshold setting determined with LED
DRIVER_HEADROOM field. Likewise, boost voltage is lowered if the voltage measured at any of the LED strings
is above the combined setting determined under LED DRIVER_HEADROOM and LED_COMP_HYST fields.
LED_COMP_HYST field serves to fine tune the headroom voltage for a given peak LED current. The boost
voltage up/down step size can be controlled with the BOOST_STEP_UP and BOOST_STEP_DN fields.
The initial boost voltage is configured with the VBOOST field. This field also sets the minimum boost voltage.
The VBOOST_MAX field sets the maximum boost voltage. When an LED pin is open, the monitored voltage
never has enough headroom, and the adaptive mode control loop keeps raising the boost voltage. The
VBOOST_MAX field allows the boost voltage to be limited to stay under the voltage rating of the external
components.
NOTE
Only LED strings that are enabled are monitored and PS_MODE field determines which
LED strings are enabled.
The adaptive mode is selected using ADAPTIVE bit set to 1 (CFGA EPROM Register) and is the recommended
mode of boost control.
VBOOST
Driver
headroom
OUT1 string VF
OUT6 string VF
OUT5 string VF
OUT4 string VF
OUT3 string VF
OUT2 string VF
OUT1 string VF
VBOOST
Time
Figure 5. Boost Adaptive Control Principle
8.3.1.3.2 Manual Control
User can control the boost output voltage with the VBOOST EPROM field when adaptive mode is not used.
Equation 1 shows the relationship between the boost output voltage and the VBOOST field.
VBOOST = VBOOST_MIN + 0.42 × VBOOST[dec]
(1)
The expression is only valid when the calculated values are between the minimum boost output voltage and the
maximum boost output voltage. The minimum boost output voltage is set with the VBOOST_RANGE field. The
maximum boost output voltage is set with the VBOOST_MAX EPROM field.
14
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
8.3.1.4 EMI Reduction
The LP8556 device features two EMI reduction schemes.
The first scheme, Programmable Slew Rate Control, uses a combination of three drivers for boost switch.
Enabling all three drivers allows boost switch on/off transition times to be the shortest. On the other hand,
enabling just one driver allows boost switch on/off transition times to be the longest. The longer the transition
times, the lower the switching noise on the SW pin. Note that the shortest transition times bring the best
efficiency as the switching losses are the lowest.
EN_DRV2 and EN_DRV3 bits in the EPROM determine the boost switch driver configuration. Refer to the SW
pin slew rate parameter listed under Electrical Characteristics — Boost Converter for the slew rate options.
The second EMI reduction scheme is the spread spectrum. This scheme deliberately spreads the frequency
content of the boost switching waveform, which inherently has a narrow bandwidth, makes the bandwidth of the
switching waveform wider, and ultimately reduces its EMI spectral density.
Duty cycle D = 1 - VIN / VOUT
tSW = 1/fSW
Slew rate control,
programmable
Spread spectrum scheme,
programmable pseudo
random duty cycle changes
minimize EMI
Figure 6. Principles of EMI Reduction Scheme
8.3.2 Brightness Control
LP8556 enables various methods of brightness control. The brightness can be controlled using an external PWM
signal or the Brightness register accessible by users via an I2C interface or both. How these two input sources
are selected and combined is set by the BRT_MODE EPROM bits and described in BRT_MODE = 00 through
BRT_MODE = 11, Figure 7, and Table 2. The LP8556 can also be preconfigured via EPROM memory to allow
direct and unaltered brightness control by an external PWM signal. This mode of operation is obtained by setting
PWM_DIRECT EPROM bit to 1 (CFG5[7] = 1).
8.3.2.1 BRT_MODE = 00
With BRT_MODE = 00, the LED output is controlled by the PWM input duty cycle. The PWM detector block
measures the duty cycle at the PWM pin and uses this 16-bit value to generate an internal to the device PWM
data. Before the output is generated, the PWM data goes through the PWM curve-shaper block. Then, the data
goes into the adaptive dimming function which determines the range of the PWM and Current control as
described in Output Dimming Schemes. The outcome of the adaptive dimming function is 12-bit current and/or
up to 6 PWM output signals. The current is then passed through the non-linear compensation block while the
output PWM signals are channeled through the dither block.
8.3.2.2 BRT_MODE = 01
With BRT_MODE = 01, the PWM output is controlled by the PWM input duty cycle and the Brightness register.
The PWM detector block measures the duty cycle at the PWM pin and uses this 16-bit value to generate the
PWM data. Before the output is generated, the PWM data is first multiplied with BRT[7:0] register, then it goes
through the PWM Curve Shaper block. Then, the data goes into the Adaptive Dimming function which
determines the range of the PWM and Current control as described in Output Dimming Schemes. The outcome
of the Adaptive Dimming function is 12-bit current and/or up to 6 PWM output signals. The current is then passed
through the non-linear compensation block while the output PWM signals are channeled through the Dither
block.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
15
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
8.3.2.3 BRT_MODE = 10
With BRT_MODE = 10, the PWM output is controlled only by the Brightness register. From BRT[7:0] register, the
data goes through the PWM Curve Shaper block. Then, the data goes into the Adaptive Dimming function which
determines the range of the PWM and Current control as described in Output Dimming Schemes. The outcome
of the Adaptive Dimming function is 12-bit Current and / or up to 6 PWM output signals. The current is then
passed through the non-linear compensation block while the output PWM signals are channeled through the
Dither block.
8.3.2.4 BRT_MODE = 11
With BRT_MODE = 11, the PWM control signal path is similar to the path when BRT_MODE = 01 except that the
PWM input signal is multiplied with BRT[7:0] data after the Curve-Shaper block.
Table 2. Brightness Control Methods Truth Table
16
PWM_DIRECT
BRT_MODE [1:0]
0
00
External PWM signal
BRIGHTNESS CONTROL SOURCE
0
01
External PWM signal and Brightness Register
(multiplied before Curve Shaper)
0
10
Brightness Register
0
11
External PWM signal and Brightness Register
(multiplied after Curve Shaper)
1
don't care
External PWM signal
Submit Documentation Feedback
OUTPUT ILED FORM
Adaptive. See Output
Dimming Schemes
Same as the external
PWM input
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
Current_Max [2:0]
BRT_MODE = 00
Current [11:0]
Non-linear
Compensation
PWM
Input
PWM
Detector
Temp Curve
Limiter Shaper
CURRENT
Adaptive
Dimming
Dither
PWM
Gen
PWM
PWM_TO_I_THRESHOLD [3:0]
Current_Max [2:0]
BRT_MODE = 01
Current [11:0]
Brightness
Non-linear
Compensation
PWM
Input
PWM
Detector
Temp Curve
Limiter Shaper
CURRENT
Adaptive
Dimming
Dither
PWM
Gen
PWM
PWM_TO_I_THRESHOLD [3:0]
Current_Max [2:0]
BRT_MODE = 10
Current [11:0]
Non-linear
Compensation
Brightness
Temp Curve
Limiter Shaper
CURRENT
Adaptive
Dimming
Dither
PWM
Gen
PWM
PWM_TO_I_THRESHOLD [3:0]
Current_Max [2:0]
BRT_MODE = 11
Current [11:0]
Non-linear
Compensation
Brightness
Temp Curve
Limiter Shaper
Dither
PWM
Input
CURRENT
Adaptive
Dimming
PWM
Gen
PWM
PWM
Detector
PWM_TO_I_THRESHOLD [3:0]
Figure 7. Brightness Control Signal Path Block Diagrams
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
17
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
8.3.2.5 Output Dimming Schemes
The LP8556 device supports three types of output dimming control methods: PWM Control, Pure Current Control
and Adaptive Dimming (Hybrid PWM and Current) Control.
8.3.2.5.1 PWM Control
PWM control is the traditional way of controlling the brightness using PWM of the outputs with the same LED
current across the entire brightness range. Brightness control is achieved by varying the duty cycle proportional
to the input PWM. PWM frequency is set either using an external set fesistor (RFSET) or using the PWM_FREQ
EPROM field. The maximum LED current is set by using an external set Resistor (RISET), CURRENT, and
CURRENT_MAX EPROM bits. PWM frequency can also be set by simply using the CURRENT and
CURRENT_MAX EPROM bits.
NOTE
The output PWM signal is de-coupled and generated independent of the input PWM signal
eliminating display flicker issues and allowing better noise immunity.
PWM CONTROL
(PWM_TO_I_THRESHOLD = 1111b)
Max current is set with CURRENT and CURRENT_MAX EPROM bits
or CURRENT and CURRENT_MAX EPROM bits and RISET resistor
LED CURRENT
100%
25%
100%
50%
BRIGHTNESS
Figure 8. PWM Only Output Dimming Scheme
8.3.2.5.2 Pure Current Control
In Pure Current Control mode, brightness control is achieved by changing the LED current proportionately from
maximum value to a minimum value across the entire brightness range. Like in PWM Control mode, the
maximum LED current is set by using an external set Resistor (RISET), CURRENT, and CURRENT_MAX EPROM
bits. The maximum LED current can also be set by just using the CURRENT and CURRENT_MAX EPROM bits.
Current resolution in this mode is 12 bits.
PURE CURRENT CONTROL
(PWM_TO_I_THRESHOLD = 0000b)
Max current is set with CURRENT and CURRENT_MAX EPROM bits
LED CURRENT
100%
or CURRENT and CURRENT_MAX EPROM bits and RISET resistor
50%
25%
25%
50%
100%
BRIGHTNESS
Figure 9. Pure Current or Analog Output Dimming Scheme
18
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
8.3.2.5.3 Adaptive Control
Adaptive dimming control combines PWM Control and Pure Current Control dimming methods. With the adaptive
dimming, it is possible to achieve better optical efficiency from the LEDs compared to pure PWM control while
still achieving smooth and accurate control at low brightness levels. Current resolution in this mode is 12 bits.
Switch point from Current to PWM control can be set with the PWM_TO_I_THRESHOLD EPROM field from 0%
to 100% of the brightness range to get good compromise between good matching of the LEDs brightness/white
point at low brightness and good optical efficiency.
PWM frequency is set either using an external set Resistor (RFSET) or using the PWM_FREQ EPROM bits. The
maximum LED current is set either by using an external set Resistor (RISET), CURRENT, and CURRENT_MAX
EPROM bits. Or the maximum LED current may be set using the CURRENT and CURRENT_MAX EPROM bits.
PWM & CURRENT CONTROL with Switch Point at 25% of ILED_MAX
(PWM_TO_I_THRESHOLD = 0111b)
PWM CONTROL
CURRENT CONTROL
LED CURRENT
100%
50%
25%
Max current is set with CURRENT and CURRENT_MAX EPROM bits
or CURRENT and CURRENT_MAX EPROM bits and RISET resistor
25%
50%
100%
BRIGHTNESS
Figure 10. Adaptive Output Dimming Scheme
8.3.2.6 Setting Full-Scale LED Current
The maximum or full-scale LED current is set either using an external set Resistor (RISET), CURRENT, and
CURRENT_MAX EPROM bits or just by using the CURRENT and CURRENT_MAX EPROM bits. Table 3
summarizes setting of the full-scale LED current.
Table 3. Setting Full-Scale LED Current
(1)
RISET [Ω]
ISET_EN
CURRENT_MAX
CURRENT[11:0]
don't care
0
000
FFFh
FULL-SCALE ILED [mA]
5
don't care
0
001
FFFh
10
don't care
0
010
FFFh
15
don't care
0
011
FFFh
20
don't care
0
100
FFFh
23
don't care
0
101
FFFh
25
don't care
0
110
FFFh
30
don't care
0
111
FFFh
50
don't care
0
000 - 111
001h - FFFh
See (1)
24k
1
000
FFFh
5
24k
1
001
FFFh
10
24k
1
010
FFFh
15
24k
1
011
FFFh
20
24k
1
100
FFFh
23
24k
1
101
FFFh
25
24k
1
110
FFFh
30
24k
1
111
FFFh
50
12k - 100k
1
000 - 111
001h - FFFh
See (1)
See CFG0.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
19
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
8.3.2.7 Setting PWM Dimming Frequency
LP8556 PWM dimming frequency can be set by an external resistor, RFSET, or by pre-configuring EPROM
Memory (CFG5 register, PWM_FREQ[3:0] bits). Table 4 summarizes setting of the PWM dimming frequency.
Note that .
NOTE
The RFSET is shared for setting the boost switching frequency, too. Setting the boost
switching frequency and PWM dimming frequency using an external resistor is shown in
Table 5.
Table 4. Configuring PWM Dimming Frequency via EPROM
RFSET [kΩ]
PWM_FSET_EN
don't care
See (1)
(1)
20
0
1
PWM_FREQ[3:0]
ƒPWM [Hz] (Resolution)
0000
4808 (11-bit)
0001
6010 (10-bit)
0010
7212 (10-bit)
0011
8414 (10-bit)
0100
9616 (10-bit)
0101
12020 (9-bit)
0110
13222 (9-bit)
0111
14424 (9-bit)
1000
15626 (9-bit)
1001
16828 (9-bit)
1010
18030 (9-bit)
1011
19232 ((9-bit)
1100
24040 (8-bit)
1101
28848 (8-bit)
1110
33656 (8-bit)
1111
38464 (8-bit)
don't care
See (1)
See Table 5.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
Table 5. Setting Switching and PWM Dimming Frequency With an External Resistor
RFSET [Ω] (Tolerance)
ƒSW [kHz]
ƒPWM [Hz] (Resolution)
Floating or FSET pin pulled HIGH
1250
9616 (10-bit)
470k - 1M (±5%)
312
2402 (12-bit)
300k, 330k (±5%)
312
4808 (11-bit)
200k (±5%)
312
6010 (10-bit)
147k, 150k, 154k, 158k (±1%)
312
9616 (10-bit)
121k (±1%)
312
12020 (9-bit)
100k (±1%)
312
14424 (9-bit)
86.6k (±1%)
312
16828 (9-bit)
75.0k (±1%)
312
19232 (9-bit)
63.4k (±1%)
625
2402 (12-bit)
52.3k, 53.6k (±1%)
625
4808 (11-bit)
44.2k, 45.3k (±1%)
625
6010 (10-bit)
39.2k (±1%)
625
9616 (10-bit)
34.0k (±1%)
625
12020 (9-bit)
30.1k (±1%)
625
14424 (9-bit)
26.1k (±1%)
625
16828 (9-bit)
23.2k (±1%)
625
19232 (9-bit)
20.5k (±1%)
1250
2402 (12-bit)
18.7k (±1%)
1250
4808 (11-bit)
16.5k (±1%)
1250
6010 (10-bit)
14.7k (±1%)
1250
9616 (10-bit)
13.0k (±1%)
1250
12020 (9-bit)
11.8k (±1%)
1250
14424 (9-bit)
10.7k (±1%)
1250
16828 (9-bit)
9.76k (±1%)
1250
19232 (9-bit)
FSET pin shorted to GND
1250
Same as PWM input
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
21
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
8.3.2.8 Phase Shift PWM Scheme
Phase shift PWM scheme allows delaying the time when each LED driver is active. When the LED drivers are
not activated simultaneously, the peak load current from the boost output is greatly decreased. This reduces the
ripple seen on the boost output and allows smaller output capacitors. Reduced ripple also reduces the output
ceramic capacitor audible ringing. PSPWM scheme also increases the load frequency seen on the boost output
six times and therefore transfers the possible audible noise to the frequencies outside of the audible range.
Description of the PSPWM mode is seen inTable 6. PSPWM mode is set with <PS_MODE[2:0]> bits.
Table 6. LED String Configuration
PS_MODE[2:0]
WAVEFORMS
Phase Delay
60 degrees
CONNECTION
Cycle Time
1/(fPWM)
VBOOST
LED1
LED2
000
LED3
1
2
3
4
5
6
5
6
LED4
LED5
LED6
6 LED strings with 60 degree phase shift. One driver for each LED string.
Phase Delay
72 degrees
Cycle Time
1/(fPWM)
VBOOST
LED1
LED2
001
1
LED3
2
3
4
LED4
LED5
5 LED strings with 72 degree phase shift. One driver for each LED string.
(Driver #6 not used).
22
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
Table 6. LED String Configuration (continued)
PS_MODE[2:0]
WAVEFORMS
Phase Delay
90 degrees
CONNECTION
Cycle Time
1/(fPWM)
VBOOST
LED1
010
LED2
1
2
3
4
5
6
5
6
5
6
LED3
LED4
4 LED strings with 90 degree phase shift. One driver for each LED string.
(Drivers #5 and #6 not used).
VBOOST
Phase Delay
120 degrees
Cycle Time
1/(fPWM)
LED1
011
LED2
1
2
3
4
LED3
3 LED strings with 120 degree phase shift. One driver for each LED string.
(Drivers #4, #5 and #6 not used).
VBOOST
Phase Delay
180 degrees
100
Cycle Time
1/(fPWM)
LED1
1
2
3
4
LED2
2 LED strings with 180 degree phase shift. One driver for each LED string.
(Drivers #3, #4, #5 and #6 not used).
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
23
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
Table 6. LED String Configuration (continued)
PS_MODE[2:0]
WAVEFORMS
Phase Delay
120 degrees
CONNECTION
Cycle Time
1/(fPWM)
VBOOST
LED1
LED2
101
LED3
1
2
3
4
5
6
5
6
LED4
LED5
LED6
3 LED strings with 120 degree phase shift. Two drivers for each LED string.
(Drivers 1&2, 3&4 and 5&6 are tied and with the same phase).
Phase Delay
180 degrees
Cycle Time
1/(fPWM)
VBOOST
LED1
LED2
110
LED3
1
2
3
4
LED4
LED5
LED6
2 LED strings with 180 degree phase shift. Three divers for each LED string.
(Drivers 1&2&3 and 4&5&6 are tied and with the same phase).
24
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
Table 6. LED String Configuration (continued)
PS_MODE[2:0]
WAVEFORMS
Phase Delay
0 degrees
CONNECTION
Cycle Time
1/(fPWM)
VBOOST
LED1
LED2
111
LED3
1
2
3
4
5
6
LED4
LED5
LED6
1 LED string driven by all six drivers.
(All drivers are tied and with the same phase).
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
25
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
8.3.2.9 Slope and Advanced Slope
Transition time between two brightness values can be programmed with EPROM bits <PWM_SLOPE[2:0]> from
0 to 500 ms. Same slope time is used for sloping up and down. With advanced slope the brightness changes can
be made more pleasing to a human eye.
Brightness (PWM)
Sloper Input
Brightness (PWM)
PWM Output
Time
Normal slope
Advanced slope
Time
Slope Time
Figure 11. Sloper Operation
8.3.2.10 Dithering
Special dithering scheme can be used during brightness changes and in steady state condition. It allows
increased resolution and smaller average steps size during brightness changes. Dithering can be programmed
with EPROM bits <DITHER[1:0]> from 0 to 3 bits. <STEADY_DITHER> EPROM bit sets whether the dithering is
used also in steady state or only during slopes. Example below is for 1-bit dithering. For 3-bit dithering, every 8th
pulse is made 1 LSB longer to increase the average value by 1/8th.
PWM value 510 (10-bit)
+1 LSB
PWM value 510 1/2 (10-bit)
PWM value 511 (10-bit)
Figure 12. Example of the Dithering, 1-bit Dither, 10-bit Resolution
26
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
8.3.3 Fault Detection
LP8556 has fault detection for LED open and short conditions, UVLO, overcurrent, and thermal shutdown. The
cause for the fault can be read from status register. Reading the fault register also resets the fault.
8.3.3.1 LED Fault Detection
With LED fault detection, the voltages across the LED drivers are constantly monitored. Shorted or open LED
strings are detected.
8.3.3.1.1 Open Detect
The logic uses the LOW comparators and the requested boost voltage to detect the OPEN condition. If the logic
is asking the boost for the maximum allowed voltage and a LOW comparator is asserted, then the OPEN bit is
set in the STATUS register (ADDR = 02h). In normal operation, the adaptive headroom control loop raises the
requested boost voltage when the LOW comparator is asserted. If it has raised it as high as it can and an LED
string still needs more voltage, then it is assumed to be disconnected from the boost voltage (open or grounded).
The actual boost voltage is not part of the OPEN condition decision; only the requested boost voltage and the
LOW comparators.
8.3.3.1.2 Short Detect
The logic uses all three comparators (HIGH, MID and LOW) to detect the SHORT condition. When the MID and
LOW comparators are de-asserted, the headroom control loop considers that string to be optimized - enough
headroom, but not excessive. If at least one LED string is optimized and at least one other LED string has its
HIGH comparator asserted, then the SHORT condition is detected. It is important to note that the SHORT
condition requires at least two strings for detection: one in the optimized headroom zone (LOW/MID/HIGH
comparators all de-asserted) and one in the excessive headroom zone (HIGH comparator asserted).
Fault is cleared by reading the fault register.
8.3.3.2 Undervoltage Detection
The LP8556 device has detection for too-low VIN voltage. Threshold level for the voltage is set with EPROM
register bits as shown in Table 7.
Table 7. UVLO Truth Table
UVLO_EN
UVLO_TH
THRESHOLD (V)
0
don't care
OFF
1
0
2.5
1
1
5.2
When undervoltage is detected the LED outputs and the boost shuts down, and the corresponding fault bit is set
in the fault register. The LEDs and the boost start again when the voltage has increased above the threshold
level. Hysteresis is implemented to threshold level to avoid continuous triggering of fault when threshold is
reached.
Fault is cleared by setting the EN / VDDIO pin low or by reading the fault register.
8.3.3.3 Overcurrent Protection
LP8556 has detection for too-high loading on the boost converter. When overcurrent fault is detected, the boost
shuts down and the corresponding fault bit is set in the fault register. The boost starts again when the current
has dropped below the OCP threshold.
Fault is cleared by reading the fault register.
8.3.3.4 Thermal Shutdown
If the LP8556 reaches thermal shutdown temperature (150°C) the LED outputs and boost shut down to protect it
from damage. The device re-activates when temperature drops below 130°C.
Fault is cleared by reading the fault register.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
27
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
8.4 Device Functional Modes
8.4.1 Shutdown Mode
The device is in shutdown mode when the EN/VDDIO input is low. Current consumption in this mode from VDD
pin is < 1.6 µA.
8.4.2 Active Mode
In active mode the backlight is enabled either with setting the ON register bit high (BRTMODE = 0 1, 10, 11) or
by activating PWM input (BRTMODE=00). The powers supplying the VDD and EN/VDDIO pins must be present.
Brightness is controlled with I2C writes to brightness registers or by changing PWM input duty cycle (operation
without I2C control). Configuration registers are not accessible in Active mode to prevent damage to the device
by accidental writes. Current consumption from VDD pin this mode is typically 2.2 mA when boost is enabled and
LEDs are not drawing any current.
8.5 Programming
8.5.1 I2C-Compatible Serial Bus Interface
8.5.1.1 Interface Bus Overview
The I2C-compatible synchronous serial interface provides access to the programmable functions and registers on
the device. This protocol uses a two-wire interface for bidirectional communications between the ICs connected
to the bus. The two interface lines are the Serial Data Line (SDA) and the Serial Clock Line (SCL). These lines
must be connected to a positive supply via a pull-up resistor and remain HIGH even when the bus is idle.
Every device on the bus is assigned a unique address and acts as either a Master or a Slave depending on
whether it generates or receives the SCL. The LP8556 can operate as an I2C slave.
8.5.1.2
Data Transactions
One data bit is transferred during each clock pulse. Data is sampled during the high state of the serial clock SCL.
Consequently, throughout the clock’s high period, the data should remain stable. Any changes on the SDA line
during the high state of the SCL and in the middle of a transaction, aborts the current transaction. New data
should be sent during the low SCL state. This protocol permits a single data line to transfer both
command/control information and data using the synchronous serial clock.
SDA
SCL
Data Line
Stable:
Data Valid
Change
of Data
Allowed
Figure 13. Bit Transfer
Each data transaction is composed of a Start Condition, a number of byte transfers (set by the software) and a
Stop Condition to terminate the transaction. Every byte written to the SDA bus must be 8 bits long and is
transferred with the most significant bit first. After each byte, an Acknowledge signal must follow. The following
sections provide further details of this process.
28
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
Programming (continued)
Data Output
by
Transmitter
Transmitter Stays Off the
Bus During the
Acknowledgment Clock
Data Output
by
Receiver
Acknowledgment
Signal From Receiver
SCL
1
2
3-6
7
8
9
S
Start
Condition
Figure 14. Start and Stop
The Master device on the bus always generates the Start and Stop Conditions (control codes). After a Start
Condition is generated, the bus is considered busy and it retains this status until a certain time after a Stop
Condition is generated. A high-to-low transition of the data line (SDA) while the clock (SCL) is high indicates a
Start Condition. A low-to-high transition of the SDA line while the SCL is high indicates a Stop Condition.
SDA
SCL
S
P
Start
Condition
Stop
Condition
Figure 15. Start and Stop Conditions
In addition to the first Start Condition, a repeated Start Condition can be generated in the middle of a transaction.
This allows another device to be accessed, or a register read cycle.
8.5.1.3 Acknowledge Cycle
The Acknowledge Cycle consists of two signals: the acknowledge clock pulse the master sends with each byte
transferred, and the acknowledge signal sent by the receiving device.
The master generates the acknowledge clock pulse on the ninth clock pulse of the byte transfer. The transmitter
releases the SDA line (permits it to go high) to allow the receiver to send the acknowledge signal. The receiver
must pull down the SDA line during the acknowledge clock pulse and ensure that SDA remains low during the
high period of the clock pulse, thus signaling the correct reception of the last data byte and its readiness to
receive the next byte.
8.5.1.4 Acknowledge After Every Byte Rule
The master generates an acknowledge clock pulse after each byte transfer. The receiver sends an acknowledge
signal after every byte received.
There is one exception to the acknowledge after every byte rule. When the master is the receiver, it must
indicate to the transmitter an end of data by not-acknowledging (“negative acknowledge”) the last byte clocked
out of the slave. This negative acknowledge still includes the acknowledge clock pulse (generated by the
master), but the SDA line is not pulled down.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
29
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
Programming (continued)
8.5.1.5 Addressing Transfer Formats
Each device on the bus has a unique slave address. The LP8556 operates as a slave device with 7-bit address
combined with data direction bit. Slave address is 2Ch as 7-bit or 58h for write and 59h for read in 8-bit format.
Before any data is transmitted, the master transmits the slave I.D. The slave device should send an acknowledge
signal on the SDA line, once it recognizes its address.
The slave address is the first seven bits after a Start Condition. The direction of the data transfer (R/W) depends
on the bit sent after the slave address — the 8th bit.
When the slave address is sent, each device in the system compares this slave address with its own. If there is a
match, the device considers itself addressed and sends an acknowledge signal. Depending upon the state of the
R/W bit (1:read, 0:write), the device acts as a transmitter or a receiver.
MSB
LSB
ADR6
Bit7
ADR5
bit6
ADR4
bit5
ADR3
bit4
ADR2
bit3
ADR1
bit2
ADR0
bit1
x
x
x
x
x
x
x
R/W
bit0
2
I C SLAVE address (chip address)
Figure 16. I2C Chip Address (0x2C)
8.5.1.6 Control Register Write Cycle
• Master device generates start condition.
• Master device sends slave address (7 bits) and the data direction bit (r/w = 0).
• Slave device sends acknowledge signal if the slave address is correct.
• Master sends control register address (8 bits).
• Slave sends acknowledge signal.
• Master sends data byte to be written to the addressed register.
• Slave sends acknowledge signal.
• If master sends further data bytes the control register address is incremented by one after acknowledge
signal.
• Write cycle ends when the master creates stop condition.
8.5.1.7 Control Register Read Cycle
• Master device generates a start condition.
• Master device sends slave address (7 bits) and the data direction bit (r/w = 0).
• Slave device sends acknowledge signal if the slave address is correct.
• Master sends control register address (8 bits).
• Slave sends acknowledge signal.
• Master device generates repeated start condition.
• Master sends the slave address (7 bits) and the data direction bit (r/w = 1).
• Slave sends acknowledge signal if the slave address is correct.
• Slave sends data byte from addressed register.
• If the master device sends acknowledge signal, the control register address is incremented by one. Slave
device sends data byte from addressed register.
• Read cycle ends when the master does not generate acknowledge signal after data byte and generates stop
condition.
30
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
Programming (continued)
Table 8. Data Read and Write Cycles
ADDRESS MODE
Data Read
<Start Condition>
<Slave Address><r/w = 0>[Ack]
<Register Addr.>[Ack]
<Repeated Start Condition>
<Slave Address><r/w = 1>[Ack]
[Register Data]<Ack or NAck>
… additional reads from subsequent register address possible
<Stop Condition>
Data Write
<Start Condition>
<Slave Address><r/w=’0’>[Ack]
<Register Addr.>[Ack]
<Register Data>[Ack]
… additional writes to subsequent register address possible
<Stop Condition>
<>Data from master [ ] Data from slave
8.5.1.8 Register Read and Write Detail
S
Slave Address
(7 bits)
'0'
A
Control Register Add.
(8 bits)
Register Data
(8 bits)
A
A
P
Data transfered,
byte + Ack
R/W
From Slave to Master
A - ACKNOWLEDGE (SDA Low)
S - START CONDITION
From Master to Slave
P - STOP CONDITION
Figure 17. Register Write Format
S
Slave Address
(7 bits)
'0' A
Control Register Add.
(8 bits)
A Sr
Slave Address
(7 bits)
R/W
'1' A
R/W
Data- Data
(8 bits)
A/
P
NA
Data transfered, byte
+
Ack/NAck
Direction of the transfer
will change at this point
From Slave to Master
A - ACKNOWLEDGE (SDA Low)
NA - ACKNOWLEDGE (SDA High)
From Master to Slave
S - START CONDITION
Sr - REPEATED START CONDITION
P - STOP CONDITION
Figure 18. Register Read Format
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
31
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
8.6 Register Maps
Table 9. Register Map
ADDR
REGISTER
D7
D6
00H
Brightness Control
D5
D4
D3
D2
D1
D0
RESET
01H
Device Control
FAST
02H
Status
OPEN
03H
ID
PANEL
04H
Direct Control
LED
0000 0000
16H
LED Enable
LED_EN
0011 1111
BRT[7:0]
0000 0000
BRT_MODE
SHORT
VREF_OK
VBOOST_OK
OVP
OCP
TSD
MFG
BL_CTL
0000 0000
UVLO
0000 0000
REV
1111 1100
Table 10. EPROM Memory Map
32
ADDR
REGISTER
D7
98H
CFG98
IBOOST_LIM_2X
9EH
CFG9E
A0H
CFG0
A1H
CFG1
A2H
CFG2
A3H
CFG3
A4H
CFG4
A5H
CFG5
A6H
CFG6
BOOST_FREQ
A7H
CFG7
RESERVED
A8H
CFG8
RESERVED
A9H
CFG9
AAH
CFGA
ABH
CFGB
ACH
CFGC
ADH
CFGD
AEH
CFGE
AFH
CFGF
D6
D5
D4
D3
D2
D1
RESERVED
RESERVED
VBOOST_RANGE
D0
RESERVED
RESERVED
HEADROOM_OFFSET
CURRENT LSB
PDET_STDBY
CURRENT_MAX
RESERVED
UVLO_EN
RESERVED
CURRENT MSB
UVLO_TH
ISET_EN
SLOPE
PWM_DIRECT
BOOST_FSET_EN
FILTER
PWM_TO_I_THRESHOLD
RESERVED
PWM_FSET_EN
PWM_INPUT_HYSTERESIS
STEADY_DITHE
R
PS_MODE
DITHER
PWM_FREQ
VBOOST
EN_DRV3
EN_DRV2
RESERVED
RESERVED
VBOOST_MAX
SSCLK_EN
BL_ON
RESERVE
D
JUMP_EN
RESERVED
IBOOST_LIM
RESERVED
RESERVED
JUMP_THRESHOLD
JUMP_VOLTAGE
ADAPTIVE
DRIVER_HEADROOM
RESERVED
RESERVED
RESERVED
RESERVED
STEP_UP
STEP_DN
LED_FAULT_TH
LED_COMP_HYST
REVISION
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
8.6.1 Register Bit Explanations
8.6.1.1 Brightness Control
Address 00h
Reset value 0000 0000b
BRIGHTNESS CONTROL REGISTER
7
6
5
4
3
2
1
0
BRT[7:0]
NAME
BIT
ACCESS
BRT
7:0
R/W
DESCRIPTION
Backlight PWM 8-bit linear control.
8.6.1.2 Device Control
Address 01h
Reset value 0000 0000b
DEVICE CONTROL REGISTER
7
6
5
4
3
FAST
2
1
BRT_MODE[1:0]
NAME
BIT
FAST
7
BRT_MODE
2:1
ACCESS
0
BL_CTL
DESCRIPTION
Skip refresh of trim and configuration registers from EPROMs when exiting the low
power STANDBY mode.
0 = read EPROMs before returning to the ACTIVE state
1 = only read EPROMs once on initial power-up.
R/W
Brightness source mode Figure 7
00b = PWM input only
01b = PWM input and Brightness register (combined before shaper block)
10b = Brightness register only
11b = PWM input and Brightness register (combined after shaper block)
BL_CTL
0
R/W
Enable backlight when Brightness Register is used to control brightness
(BRT_MODE = 10).
0 = Backlight disabled and chip turned off
1 = Backlight enabled and chip turned on
This bit has no effect when PWM pin control is selected for brightness control
(BRT_MODE = 00). In this mode the state of PWM pin enable or disables the chip.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
33
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
8.6.1.3 Status
Address 02h
Reset value 0000 0000b
FAULT REGISTER
7
6
5
4
3
2
1
0
OPEN
SHORT
VREF_OK
VBOOST_OK
OVP
OCP
TSD
UVLO
NAME
BIT
ACCESS
OPEN
7
R
DESCRIPTION
LED open fault detection
0 = No fault
1 = LED open fault detected. The value is not latched.
SHORT
6
R
LED short fault detection
0 = No fault
1 = LED short fault detected. The value is not latched.
VREF_OK
5
R
Internal VREF node monitor status
1 = VREF voltage is OK.
VBOOST_OK
4
R
Boost output voltage monitor status
0 = Boost output voltage has not reached its target (VBOOST < Vtarget – 2.5V)
1 = Boost output voltage is OK. The value is not latched.
OVP
3
R
Overvoltage protection
0 = No fault
1 = Overvoltage condition occurred. Fault is cleared by reading the register 02h.
OCP
2
R
Over current protection
0 = No fault
1 = Overcurrent condition occurred. Fault bit is cleared by reading this register.
TSD
1
R
Thermal shutdown
0 = No fault
1 = Thermal fault generated, 150°C reached. Boost converter and LED outputs are
disabled until the temperature has dropped down to 130°C. Fault is cleared by reading
this register.
UVLO
0
R
Undervoltage detection
0 = No fault
1 = Undervoltage detected on the VDD pin. Boost converter and LED outputs are
disabled until VDD voltage is above the UVLO threshold voltage. Threshold voltage is
set with EPROM bits. Fault is cleared by reading this register.
34
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
8.6.1.4 Identification
Address 03h
Reset value 1111 1100b
IDENTIFICATION REGISTER
7
6
5
4
PANEL
3
2
MFG[3:0]
1
0
REV[2:0]
NAME
BIT
ACCESS
DESCRIPTION
PANEL
7
R
Panel ID code
MFG
6:3
R
Manufacturer ID code
REV
2:0
R
Revision ID code
8.6.1.5 Direct Control
Address 04h
Reset value 0000 0000b
DIRECT CONTROL REGISTER
7
6
5
4
3
2
1
0
OUT[5:0]
NAME
BIT
ACCESS
OUT
5:0
R/W
DESCRIPTION
Direct control of the LED outputs
0 = Normal operation. LED output are controlled with the adaptive dimming block
1 = LED output is forced to 100% PWM.
8.6.1.6 LED String Enable
Address 16h
Reset value 0011 1111b
TEMP LSB REGISTER
7
6
5
4
3
2
1
0
LED_EN[5:0]
NAME
BIT
ACCESS
LED_EN
5:0
R/W
DESCRIPTION
Bits 5:0 correspond to LED Strings 6:1 respectively.
Bit value 1 = LED String Enabled
Bit value 0 = LED String Disabled
Note: To disable string(s), it is recommended to disable higher order string(s). For
example, for 5-string configuration, disable 6th String. For 4-string configuration,
disable 6th and 5th string. These bits are ANDed with the internal LED enable bits
that are generated with the PS_MODE logic.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
35
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
8.6.2 EPROM Bit Explanations
8.6.2.1 LP8556TM (DSBGA) Configurations and Pre-Configured EPROM Settings
ADDRESS
(1)
LP8556-E02
LP8556-E03
LP8556-E04
LP8556-E05 (1)
98h[7]
0b
0b
0b
0b
9Eh
22h
24h
24h
22h
A0h
FFh
FFh
FFh
A1h
5Fh
BFh
3Fh
A2h
20h
28h
2Fh
A3h
5Eh
5Eh
5Eh
A4h
72h
72h
72h
A5h
04h
14h
04h
A6h
80h
80h
80h
A7h
F7h
F7h
F7h
A9h
80h
A0h
60h
AAh
0Fh
0Fh
0Fh
ABh
00h
00h
00h
ACh
00h
00h
00h
ADh
00h
00h
00h
AEh
0Fh
0Fh
0Fh
AFh
05h
03h
03h
LP8556-E05 is a device option with un-configured EPROM settings. This option is for users that desire programming the device by
themselves. Bits 98h[7] and 9Eh[5] are always pre-configured.
8.6.2.2 LP8556TM (DSBGA) Configurations and Pre-configured EPROM Settings Continued
ADDRESS
36
LP8556-E06
LP8556-E07
LP8556-E09
LP8556-E11
98h[7]
0b
0b
0b
0b
9Eh
22h
04h
22h
02h
A0h
FFh
FFh
FFh
FFh
A1h
DBh
BFh
CFh
4Fh
A2h
2Fh
0Dh
2Fh
20h
A3h
02h
02h
02h
03h
A4h
72h
72h
72h
12h
A5h
14h
20h
04h
3Ch
A6h
40h
4Eh
80h
40h
A7h
F7h
F6h
F7h
F4h
A9h
DBh
C0h
A0h
80h
AAh
0Fh
0Fh
0Fh
0Fh
ABh
00h
00h
00h
00h
ACh
00h
00h
00h
00h
ADh
00h
00h
00h
00h
AEh
0Fh
0Fh
0Eh
0Fh
AFh
05h
03h
05h
01h
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
8.6.2.3 LP8556SQ (WQFN) Configurations and Pre-configured EPROM Settings
ADDRESS
LP8556-E00
LP8556-E08
LP8556-E09
98h[7]
1b
1b
1b
9Eh
22h
22h
22h
A0h
FFh
FFh
FFh
A1h
CFh
CFh
CFh
A2h
2Fh
2Fh
2Fh
A3h
5Eh
5Eh
02h
A4h
72h
72h
72h
A5h
14h
24h
04h
A6h
80h
80h
80h
A7h
F6h
F6h
F6h
A9h
A0h
A0h
A0h
AAh
0Fh
0Fh
0Fh
ABh
00h
00h
00h
ACh
00h
00h
00h
ADh
00h
00h
00h
AEh
0Fh
0Fh
0Fh
AFh
01h
01h
01h
8.6.2.4 CFG98
Address 98h
CFG98 REGISTER
7
6
5
4
NAME
BIT
ACCESS
IBOOST_LIM_2X
7
R/W
3
2
1
0
IBOOST_LIM_2X
(1)
DESCRIPTION
Select the inductor current limit range.
When IBOOST_LIM_2X = 0, the inductor current limit can be set to 0.9 A, 1.2 A, 1.5 A or 1.8
A.
When IBOOST_LIM_2X = 1, the inductor current limit can be set to 1.6 A, 2.1 A, or 2.6 A .
This option is supported only on WQFN package and not on DSBGA package. See (1).
1.8 A is the maximum ISW_LIM supported with the DSBGA package. For applications requiring the ISW_LIM to be greater than 1.8 A and
up to 2.6 A, WQFN package should be considered.
8.6.2.5 CFG9E
Address 9Eh
CFG9E REGISTER
7
6
5
4
3
VBOOST_RANGE
2
1
0
HEADROOM_OFFSET
NAME
BIT
ACCESS
VBOOST_RANGE
5
R/W
DESCRIPTION
Select VBOOST range.
When VBOOST_RANGE = 0, the output voltage range is from 7 V to 34 V
When VBOOST_RANGE = 1, the output voltage range is from 16 V to 43 V
HEADROOM_
OFFSET
3:0
R/W
LED driver headroom offset. This adjusts the LOW comparator threshold together
with LED_HEADROOM bits and contributes to the MID comparator threshold.
0000 = 460 mV
0001 = 390 mV
0010 = 320 mV
0100 = 250 mV
1000 = 180 mV
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
37
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
8.6.2.6 CFG0
Address A0h
CFG0 REGISTER
7
6
5
4
3
2
1
0
CURRENT LSB[7:0]
NAME
BIT
ACCESS
DESCRIPTION
CURRENT LSB
7:0
R/W
The 8-bits in this register (LSB) along the 4-bits defined in CFG1 Register (MSB) allow
LED current to be set in 12-bit fine steps. These 12-bits further scale the maximum LED
current set using CFG1 Register, CURRENT_MAX bits (denoted as IMAX ). If ISET_EN =
0, the LED current is defined with the bits as shown below. If ISET_EN = 1, then the
external resistor connected to the ISET pin scales the LED current as shown below.
ISET_EN = 0
ISET_EN = 1
0000 0000 0000
0A
0A
0000 0000 0001
(1/4095) ×
IMAX
(1/4095) × IMAX × 20,000 × 1.2V
/ RISET
0000 0000 0010
(2/4095) ×
IMAX
(2/4095) x IMAX × 20,000 × 1.2V
/ RISET
...
...
...
0111 1111 1111
(2047/4095)
× IMAX
(2047/4095) × IMAX × 20,000 ×
1.2V / RISET
...
...
...
1111 1111 1101
(4093/4095)
× IMAX
(4093/4095) × IMAX × 20,000 ×
1.2V / RISET
1111 1111 1110
(4094/4095)
× IMAX
(4094/4095) × IMAX × 20,000 x
1.2V / RISET
1111 1111 1111
(4095/4095)
× IMAX
(4095/4095) × IMAX × 20,000 x
1.2V / RISET
8.6.2.7 CFG1
Address A1h
CFG1 REGISTER
7
6
PDET_STDBY
NAME
5
4
3
CURRENT_MAX[2:0]
BIT
ACCESS
2
1
0
CURRENT MSB[11:8]
DESCRIPTION
PDET_STDBY
7
R/W
Enable Standby when PWM input is constant low (approx. 50 ms timeout).
CURRENT_MAX
6:4
R/W
Set Maximum LED current as shown below. This maximum current is scaled as
described in the CFG0 Register.
000 = 5 mA
001 = 10 mA
010 = 15 mA
011 = 20 mA
100 = 23 mA
101 = 25 mA
110 = 30 mA
111 = 50 mA
CURRENT MSB
3:0
R/W
These bits form the 4 MSB bits for LED Current as described in CFG0 Register.
38
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
8.6.2.8 CFG2
Address A2h
CFG2 REGISTER
7
6
RESERVED
5
4
3
2
1
0
UVLO_EN
UVLO_TH
BL_ON
ISET_EN
BOOST_
_FSET_EN
PWM_
_FSET_EN
NAME
BIT
ACCESS
RESERVED
7:6
R/W
DESCRIPTION
UVLO_EN
5
R/W
Undervoltage lockout protection enable.
UVLO_TH
4
R/W
UVLO threshold levels:
0 = 2.5 V
1 = 5.2 V
BL_ON
3
R/W
Enable backlight. This bit must be set for PWM only control.
0 = Backlight disabled. This selection is recommended for systems with an I2C
master. With an I2C master, the backlight can be controlled by writing to the
register 01h.
1 = Backlight enabled. This selection is recommended for systems with PWM
only control.
ISET_EN
2
R/W
Enable LED current set resistor.
0 = Resistor is disabled and current is set with CURRENT and CURRENT_MAX
EPROM register bits.
1 = Resistor is enabled and current is set with the RISET resistor AND
CURRENT AND CURRENT_MAX EPROM register bits.
BOOST_FSET_EN
1
R/W
Enable configuration of the switching frequency via FSET pin.
0 = Configuration of the switching frequency via FSET pin is is disabled. The
switching frequency is set with BOOST_FREQ EPROM register bits.
1 = Configuration of the switching frequency via FSET pin is is enabled.
PWM_FSET_EN
0
R/W
Enable configuration of the PWM dimming frequency via FSET pin.
0 = Configuration of the switching frequency via FSET pin is is disabled. The
switching frequency is set with PWM_FREQ EPROM register bits.
1 = Configuration of the PWM dimming frequency via FSET pin is is enabled.
6
5
8.6.2.9 CFG3
Address A3h
CFG3 REGISTER
7
RESERVED
4
SLOPE[2:0]
3
2
1
FILTER[1:0]
0
PWM_INPUT_HYSTERESIS[1:0]
NAME
BIT
ACCESS
RESERVED
7
R/W
DESCRIPTION
SLOPE
6:4
R/W
Select brightness change transition duration
000 = 0 ms (immediate change)
001 = 1 ms
010 = 2 ms
011 = 50 ms
100 = 100 ms
101 = 200 ms
110 = 300 ms
111 = 500 ms
FILTER
3:2
R/W
Select brightness change transition filtering strength
00 = No filtering
01 = light smoothing
10 = medium smoothing
11 = heavy smoothing
PWM_INPUT_
_HYSTERESIS
1:0
R/W
PWM input hysteresis function.
00 = OFF
01 = 1-bit hysteresis with 13-bit resolution
10 = 1-bit hysteresis with 12-bit resolution
11 = 1-bit hysteresis with 8-bit resolution
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
39
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
8.6.2.10 CFG4
Address A4h
CFG4 REGISTER
7
6
5
PWM_TO_I_THRESHOLD[3:0]
NAME
BIT
ACCESS
PWM_TO_I_THRESHOLD
7:4
R/W
40
4
3
2
RESERVED
STEADY_
_DITHER
1
0
DITHER[1:0]
DESCRIPTION
Select switch point between PWM and pure current dimming
0000 = current dimming across entire range
0001 = switch point at 10% of the maximum LED current.
0010 = switch point at 12.5% of the maximum LED current.
0011 = switch point at 15% of the maximum LED current.
0100 = switch point at 17.5% of the maximum LED current.
0101 = switch point at 20% of the maximum LED current.
0110 = switch point at 22.5% of the maximum LED current.
0111 = switch point at 25% of the maximum LED current. This is a
recommended selection.
1000 = switch point at 33.33% of the maximum LED current.
1001 = switch point at 41.67% of the maximum LED current.
1010 = switch point at 50% of the maximum LED current.
1011 to 1111 = PWM dimming across entire range
RESERVED
3
R/W
STEADY_DITHER
2
R/W
Dither function method select:
0 = Dither only on transitions
1 = Dither at all times
DITHER
1:0
R/W
Dither function control
00 = Dithering disabled
01 = 1-bit dithering
10 = 2-bit dithering
11 = 3-bit dithering
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
8.6.2.11 CFG5
Address A5h
CFG5 REGISTER
7
6
PWM_DIRECT
5
4
3
PS_MODE[2:0]
2
1
0
PWM_FREQ[3:0]
NAME
BIT
ACCESS
PWM_DIRECT
7
R/W
DESCRIPTION
Intended for certain test mode purposes. When enabled, the entire pipeline is
bypassed and PWM output is connected with PWM input.
PS_MODE
6:4
R/W
Select PWM output phase configuration:
000 = 6-phase, 6 drivers (0°, 60°, 120°, 180°, 240°, 320°)
001 = 5-phase, 5 drivers (0°, 72°, 144°, 216°, 288°, OFF)
010 = 4-phase, 4 drivers (0°, 90°, 180°, 270°, OFF, OFF)
011 = 3-phase, 3 drivers (0°, 120°, 240°, OFF, OFF, OFF)
100 = 2-phase, 2 drivers (0°, 180°, OFF, OFF, OFF, OFF)
101 = 3-phase, 6 drivers (0°, 0°, 120°, 120°, 240°, 240°)
110 = 2-phase, 6 drivers (0°, 0°, 0°, 180°, 180°, 180°)
111 = 1-phase, 6 drivers (0°, 0°, 0°, 0°, 0°, 0°)
PWM_FREQ
3:0
R/W
0h = 4,808 Hz (11-bit)
1h = 6,010 Hz (10-bit)
2h = 7,212 Hz (10-bit)
3h = 8,414 Hz (10-bit)
4h = 9,616 Hz (10-bit)
5h = 12,020 Hz (9-bit)
6h = 13,222 Hz (9-bit)
7h = 14,424 Hz (9-bit)
8h = 15,626 Hz (9-bit)
9h = 16,828 Hz (9-bit)
Ah = 18,030 Hz (9-bit)
Bh = 19,232 Hz (9-bit)
Ch = 24,040 Hz (8-bit)
Dh = 28,848 Hz (8-bit)
Eh = 33,656 Hz (8-bit)
Fh = 38,464 Hz(8-bit)
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
41
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
8.6.2.12 CFG6
Address A6h
CFG6 REGISTER
7
6
5
4
BOOST_FREQ[1:0]
3
2
1
0
VBOOST[5:0]
NAME
BIT
ACCESS
BOOST_FREQ
7:6
R/W
DESCRIPTION
Set boost switching frequency when BOOST_FSET_EN = 0.
00 = 312 kHz
01 = 625 kHz
10 = 1250 kHz
11 = undefined
VBOOST
5:0
R/W
Boost output voltage. When ADAPTIVE = 1, this is the boost minimum and
initial voltage.
8.6.2.13 CFG7
Address A7h
CFG7 REGISTER
7
6
RESERVED
42
5
4
EN_DRV3
EN_DRV2
ACCESS
3
2
RESERVED
1
0
IBOOST_LIM[1:0]
NAME
BIT
DESCRIPTION
RESERVED
7:6
EN_DRV3
5
R/W
Selects boost driver strength to set boost slew rate. See EMI Reduction for
more detail.
0 = Driver3 disabled
1 = Driver3 enabled
EN_DRV2
4
R/W
Selects boost driver strength to set boost slew rate. See EMI Reduction for
more detail.
0 = Driver2 disabled
1 = Driver2 enabled
RESERVED
3:2
R/W
IBOOST_LIM
1:0
R/W
Select boost inductor current limit
(IBOOST_LIM_2X = 0 / IBOOST_LIM_2X = 1)
00 = 0.9 A / 1.6 A
01 = 1.2 A / 2.1 A
10 = 1.5 A / 2.6 A
11 = 1.8 A / not permitted
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
8.6.2.14 CFG9
Address A9h
CFG9 REGISTER
7
6
5
4
VBOOST_MAX[2:0]
JUMP_EN
3
2
1
JUMP_THRESHOLD[1:0]
NAME
BIT
ACCESS
VBOOST_MAX
7:5
R/W
Select the maximum boost voltage (typ values)
( VBOOST_RANGE = 0 / VBOOST_RANGE = 1)
010 = NA / 21 V
011 = NA / 25 V
100 = 21 V / 30 V
101 = 25 V / 34.5 V
110 = 30 V / 39 V
111 = 34 V / 43 V
0
JUMP_VOLTAGE[1:0]
DESCRIPTION
JUMP_EN
4
R/W
Enable JUMP detection on the PWM input.
JUMP_THRESHOLD
3:2
R/W
Select JUMP threshold:
00 = 10%
01 = 30%
10 = 50%
11 = 70%
JUMP_VOLTAGE
1:0
R/W
Select JUMP voltage:
00 = 0.5 V
01 = 1 V
10 = 2 V
11 = 4 V
8.6.2.15 CFGA
Address AAh
CFGA REGISTER
7
6
SSCLK_EN
RESERVED
5
4
NAME
BIT
ACCESS
RESERVED
3
ADAPTIVE
2
1
0
DRIVER_HEADROOM[2:0]
DESCRIPTION
SSCLK_EN
7
R/W
RESERVED
6
R/W
Enable spread spectrum function
RESERVED
5:4
R/W
ADAPTIVE
3
R/W
Enable adaptive boost control
DRIVER_HEADROOM
2:0
R/W
LED driver headroom control. This sets the LOW comparator threshold and
contributes to the MID comparator threshold.
000 = HEADROOM_OFFSET + 875 mV
001 = HEADROOM_OFFSET + 750 mV
010 = HEADROOM_OFFSET + 625 mV
011 = HEADROOM_OFFSET + 500 mV
100 = HEADROOM_OFFSET + 375 mV
101 = HEADROOM_OFFSET + 250 mV
110 = HEADROOM_OFFSET + 125 mV
111 = HEADROOM_OFFSET mV
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
43
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
8.6.2.16 CFGE
Address AEh
CFGE REGISTER
7
6
5
STEP_UP[1:0]
4
STEP_DN[1:0]
3
2
1
LED_FAULT_TH[2:0]
0
LED_COMP_HYST[1:0]
NAME
BIT
ACCESS
STEP_UP
7:6
R/W
DESCRIPTION
Adaptive headroom UP step size
00 = 105 mV
01 = 210 mV
10 = 420 mV
11 = 840 mV
STEP_DN
5:4
R/W
Adaptive headroom DOWN step size
00 = 105 mV
01 = 210 mV
10 = 420 mV
11 = 840 mV
LED_FAULT_TH
3:2
R/W
LED headroom fault threshold. This sets the HIGH comparator threshold.
00 = 5 V
01 = 4 V
10 = 3 V
11 = 2 V
LED_COMP_HYST
1:0
R/W
LED headrom comparison hysteresis. This sets the MID comparator threshold.
00 = DRIVER_HEADROOM + 1000 mV
01 = DRIVER_HEADROOM + 750 mV
10 = DRIVER_HEADROOM + 500 mV
11 = DRIVER_HEADROOM + 250 mV
8.6.2.17 CFGF
Address AFh
CFGF REGISTER
7
6
5
4
3
2
1
0
REVISION
44
NAME
BIT
ACCESS
REV
7:0
R/W
DESCRIPTION
EPROM Settings Revision ID code
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
9.1.1 Using LP8556 With I2C Host
9.1.1.1 Setting Boost Switching and PWM Dimming Frequencies
Boost switching and PWM dimming frequencies can be set via EEPROM when BOOST_FSET_EN = 0 and
PWM_FSET_EN = 0. Available options are shown in Table 11 and Table 12.
Table 11. Configuring Boost Switching Frequency via EPROM
BOOST_FSET_EN
BOOST_FREQ[1:0]
ƒSW [kHz]
0
00
312
0
01
625
0
10
1250
0
11
Reserved
Table 12. Configuring PWM Dimming Frequency via EPROM
PWM_FSET_EN
PWM_FREQ[3:0]
ƒPWM [Hz] (Resolution)
0
0000
4808 (11-bit)
0
0001
6010 (10-bit)
0
0010
7212 (10-bit)
0
0011
8414 (10-bit)
0
0100
9616 (10-bit)
0
0101
12020 (9-bit)
0
0110
13222 (9-bit)
0
0111
14424 (9-bit)
0
1000
15626 (9-bit)
0
1001
16828 (9-bit)
0
1010
18030 (9-bit)
0
1011
19232 (9-bit)
0
1100
24040 (8-bit)
0
1101
28848 (8-bit)
0
1110
33656 (8-bit)
0
1111
38464 (8-bit)
9.1.1.2 Setting Full-Scale LED Current
The LED current per output is configured by programming the CURRENT_MAX and CURRENT registers when
ISET_EN = 0. Available options are shown below.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
45
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
Table 13. Setting Full-Scale LED Current with EEPROM
ISET_EN
CURRENT_MAX
CURRENT[11:0]
FULL-SCALE ILED [mA]
0
0
FFFh
5
0
1
FFFh
10
0
10
FFFh
15
0
11
FFFh
20
0
100
FFFh
23
0
101
FFFh
25
0
110
FFFh
30
0
111
FFFh
50
0
000 – 111
001h – FFFh
(CURRENT/4095) × CURRENT_IMAX
9.1.2 Using LP8556 With Configuration Resistors and IO Pins
9.1.2.1 Setting Boost Switching and PWM Dimming Frequencies
Boost switching and PWM dimming frequencies can be set via resistor when BOOST_FSET_EN = 1 and
PWM_FSET_EN = 1. Available options are shown in Table 14.
Table 14. Configuring PWM Dimming Frequency With an External Resistor
46
RFSET [kΩ]
(TOLERANCE)
ƒSW [kHz]
BOOST_FSET_EN = 1
ƒPWM [Hz] (RESOLUTION)
PWM_FSET_EN = 1
Floating or FSET pin pulled HIGH
1250
9616 (10-bit)
470 k - 1 M (±5%)
312
2402 (12-bit)
300 k, 330 k (±5%)
312
4808 (11-bit)
200 k (±5%)
312
6010 (10-bit)
147 k, 150k, 154 k, 158k (±1%)
312
9616 (10-bit)
121 k (±1%)
312
12020 (9-bit)
100 k (±1%)
312
14424 (9-bit)
86.6 k (±1%)
312
16828 (9-bit)
75 k (±1%)
312
19232 (9-bit)
63.4 k (±1%)
625
2402 (12-bit)
52.3 k, 53.6 k (±1%)
625
4808 (11-bit)
44.2k, 45.3 k (±1%)
625
6010 (10-bit)
39.2 k (±1%)
625
9616 (10-bit)
34 k (±1%)
625
12020 (9-bit)
30.1k (±1%)
625
14424 (9-bit)
26.1 k (±1%)
625
16828 (9-bit)
23.2 k (±1%)
625
19232 (9-bit)
20.5 k (±1%)
1250
2402 (12-bit)
18.7 k (±1%)
1250
4808 (11-bit)
16.5k (±1%)
1250
6010 (10-bit)
14.7 k (±1%)
1250
9616 (10-bit)
13 k (±1%)
1250
12020 (9-bit)
11.8k (±1%)
1250
14424 (9-bit)
10.7 k (±1%)
1250
16828 (9-bit)
9.76 k (±1%)
1250
19232 (9-bit)
FSET pin shorted to GND
1250
Same as PWM input frequency
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
9.1.2.2 Setting Full-Scale LED Current
The LED current per output is configured by ISET resistor when ISET_EN=1. In this mode the CURRENT_IMAX
and CURRENT registers can also further scale the LED current. Available options are shown in Table 15.
Table 15. Setting Full-Scale LED Current with ISET Resistor
RISET [Ω]
ISET_EN
CURRENT_MAX
CURRENT[11:0]
FULL-SCALE ILED [mA]
24 k
1
0
FFFh
5
24 k
1
1
FFFh
10
24 k
1
10
FFFh
15
24 k
1
11
FFFh
20
24 k
1
100
FFFh
23
24 k
1
101
FFFh
25
24 k
1
110
FFFh
30
24 k
1
111
FFFh
50
12 k – 100 k
1
000–111
001h–FFFh
(CURRENT/4095) × IMAX × 20,000 × 1.2 V / RISET
9.2 Typical Application
7V ± 43V
L1
2.7V - 36V
D1
1.1 ” 9OUT / VIN ” 15
VOUT
VIN
CIN
2.7V ± 20V
VDD
COUT
SW
VDD
CVDD
VBOOST
EN / VDDIO
1.62V ± 3.6V
EN / VDDIO
LED1
CVLDO
VLDO
LED2
RFSET
FSET
RISET
LP8556
LED3
ISET
LED4
Optional
LED5
PWM
MCU
LED6
SDA
SCL
GNDs
Figure 19. LP8556 Typical Application Schematic
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
47
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
Typical Application (continued)
9.2.1 Design Requirements
Table 16. Recommended Inductance
ƒSW
MIN
1250
3.3
625
312
TYP
MAX
UNIT
22
µH
6.8
68
µH
10
100
µH
MAX
UNIT
Table 17. Recommended Output Capacitance
ƒSW
MIN
TYP
1250
4.7
µF
625
4.7
µF
312
10
µF
9.2.2 Detailed Design Procedure
9.2.2.1 Recommended Inductance for the Boost Power Stage
Assumes 20 mA as the maximum LED current per string and 3.3 V as the maximum LED forward voltage.
NUMBER OF
LED STRINGS
NUMBER OF
LEDS PER
STRING
6
6
L1 INDUCTANCE
BOOST INPUT
VOLTAGE RANGE
ƒSW = 1250 kHz
ƒSW = 625 kHz
ƒSW = 312 kHz
2.7 V - 4.4 V
3.3 μH - 6.8 μH
6.8 μH - 15 μH
10 μH - 33 μH
5.4 V - 8.8 V
10 μH - 22 μH
22 μH - 47 μH
47 μH - 100 μH
2.7 V - 4.4 V
4.7 μH - 10 μH
10 μH - 15 μH
22 μH - 33 μH
5.4 V - 8.8 V
10 μH - 22 μH
22 μH - 68 μH
47 μH - 100 μH
6
8
4
10
5.4 V - 8.8 V
6.8 μH - 22 μH
22 μH - 47 μH
47 μH - 100 μH
4
12
5.4 V - 8.8 V
10 μH - 22 μH
22 μH - 47 μH
33 μH - 100 μH
9.2.2.2 Recommended Capacitances for the Boost and LDO Power Stages (1)
(1)
48
SWITCHING FREQUENCY [kHz]
CIN [μF]
COUT [μF]
CVLDO [μF]
1250
2.2
4.7
10
625
2.2
4.7
10
312
4.7
10
10
Capacitance of Multi-Layer Ceramic Capacitors (MLCC) can change significantly with the applied DC voltage. Use capacitors with good
capacitance versus DC bias characteristics. In general, MLCC in bigger packages have lower capacitance de-rating than physically
smaller capacitors.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
9.2.3 Application Curves
Unless otherwise specified: VIN = 3.8 V, CVLDO = 10 μF, L1 = 4.7 μH, CIN = 2.2 μF, COUT = 4.7 μF, ƒSW = 1.25 MHz
95
95
Boost Efficiency
85
EFFICIENCY [%]
EFFICIENCY [%]
85
Boost Efficiency
LED Efficiency
75
VIN = 3.8V
6x7 LED Array
ILEDMAX = 20 mA/CH
L = 10 PH
1.5 mm Max Height
fSW = 625 kHz
65
55
LED Efficiency
75
VIN = 6.3V
6x7 LED Array
ILEDMAX = 20 mA/CH
L = 10 PH
1.5 mm Max Height
fSW = 625 kHz
65
55
45
45
0
20
40
60
80
100
0
20
BRIGHTNESS [%]
80
100
BRIGHTNESS [%]
Figure 21. Boost and LED Drive Efficiency
95
95
Boost Efficiency
Boost Efficiency
85
EFFICIENCY [%]
EFFICIENCY [%]
60
Figure 20. Boost and LED Drive Efficiency
85
LED Efficiency
75
VIN = 8.6V
6x7 LED Array
ILEDMAX = 20 mA/CH
L = 10 PH
1.5 mm Max Height
fSW = 625 kHz
65
55
LED Efficiency
75
VIN = 12.9V
6x7 LED Array
ILEDMAX = 20 mA/CH
L = 10 PH
1.5 mm Max Height
fSW = 625 kHz
65
55
45
45
0
20
40
60
80
100
0
20
BRIGHTNESS [%]
40
60
80
100
BRIGHTNESS [%]
Figure 22. Boost and LED Drive Efficiency
Figure 23. Boost and LED Drive Efficiency
200
500
Adaptive Dimming
Adaptive Dimming
180
400
PWM Dimming
LUMINANCE [Nits]
OPTICAL EFFICIENCY [Nits/W]
40
160
VIN = 3.6V
10" Panel
6x7 LED Array
ILEDMAX = 23 mA/CH
L = 4.7 PH
1.5 mm Max Height
fSW = 1.25 MHz
140
120
PWM Dimming
300
VIN = 3.6V
10" Panel
6x7 LED Array
ILEDMAX = 23 mA/CH
L = 4.7 PH
1.5 mm Max Height
fSW = 1.25 MHz
200
100
100
0
0
20
40
60
80
100
0
BRIGHTNESS [%]
Figure 24. Optical Efficiency
20
40
60
80
100
BRIGHTNESS [%]
Figure 25. Luminance as a Function of Brightness
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
49
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
Unless otherwise specified: VIN = 3.8 V, CVLDO = 10 μF, L1 = 4.7 μH, CIN = 2.2 μF, COUT = 4.7 μF, ƒSW = 1.25 MHz
5
100
INPUT POWER [W]
4
3
2
POWER SAVINGS [mW]
VIN = 3.6V
10" Panel
6x7 LED Array
ILEDMAX = 23 mA/CH
L = 4.7 PH
1.5 mm Max Height
fSW = 1.25 MHz
PWM Dimming
1
80
60
VIN = 3.6V
10" Panel
6x7 LED Array
ILEDMAX = 23 mA/CH
L = 4.7 PH
1.5 mm Max Height
fSW = 1.25 MHz
40
20
Adaptive Dimming
0
0
0
100
200
300
400
500
0
LUMINANCE [Nits]
40
60
80
100
BRIGHTNESS [%]
Figure 26. Input Power as a Function of Brightness
50
20
Figure 27. Power Savings With Adaptive Dimming when
Compared to PWM Dimming
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
10 Power Supply Recommendations
The device is designed to operate from a VDD input voltage supply range from 2.7 V to 20 V. This input supply
must be well regulated and able to withstand maximum input current and maintain stable voltage without voltage
drop even at load transition condition (start-up or rapid brightness change). The resistance of the input supply rail
must be low enough that the input current transient does not cause drop high enough in the LP8556 supply
voltage that can cause false UVLO fault triggering.
If the input supply is located more than a few inches from the LP8556 device, additional bulk capacitance may be
required in addition to the ceramic bypass capacitors. Depending on device EEPROM configuration and usage
case the boost converter is configured to operate optimally with certain input voltage range.
11 Layout
11.1 Layout Guidelines
Figure 28 and Figure 29 follow proper layout guidelines and should be used as a guide for laying out the LP8556
circuit.
The LP8556 inductive boost converter has a high switched voltage at the SW pin, and a step current through the
Schottky diode and output capacitor each switching cycle. The high switching voltage can create interference into
nearby nodes due to electric field coupling (I = C × dV/dt). The large step current through the diode and the
output capacitor can cause a large voltage spike at the SW and VBOOST pins due to parasitic inductance in the
step current conducting path (V = L × di/dt). Board layout guidelines are geared towards minimizing this electric
field coupling and conducted noise.
The following list details the main (layout sensitive) areas of the device inductive boost converter in order of
decreasing importance:
1. Boost Output Capacitor Placement
– Because the output capacitor is in the path of the inductor current discharge path, there is a high-current
step from 0 to IPEAK each time the switch turns off and the Schottky diode turns on. Any inductance
along this series path from the diodes cathode, through COUT, and back into the LP8556 GND pin
contributes to voltage spikes (VSPIKE = LP_ × dI/dt) at SW and OUT. These spikes can potentially overvoltage the SW and VBOOST pins, or feed through to GND. To avoid this, COUT+ must be connected as
close to the cathode of the Schottky diode as possible, and COUT− must be connected as close to the
LP8556 GND bumps as possible. The best placement for COUT is on the same layer as the LP8556 to
avoid any vias that can add excessive series inductance.
2. Schottky Diode Placement
– In the device boost circuit the Schottky diode is in the path of the inductor current discharge. As a result
the Schottky diode has a high-current step from 0 to IPEAK each time the switch turns off and the diode
turns on. Any inductance in series with the diode causes a voltage spike (VSPIKE = LP_ × dI/dt) at SW
and OUT. This can potentially over-voltage the SW pin, or feed through to VOUT and through the output
capacitor, into GND. Connecting the anode of the diode as close to the SW pin as possible, and
connecting the cathode of the diode as close to COUT+ as possible reduces the inductance (LP_) and
minimize these voltage spikes.
3. Boost Input/VDD Capacitor Placement
– The LP8556 input capacitor filters the inductor current ripple and the internal MOSFET driver currents.
The inductor current ripple can add input voltage ripple due to any series resistance in the input power
path. The MOSFET driver currents can add voltage spikes on the input due to the inductance in series
with the VIN/VDD and the input capacitor. Close placement of the input capacitor to the VDD pin and to
the GND pin is critical because any series inductance between VIN/VDD and CIN+ or CIN– and GND can
create voltage spikes that could appear on the VIN/VDD supply line and GND.
– Close placement of the input capacitor at the input side of the inductor is also critical. The source
impedance (inductance and resistance) from the input supply, along with the input capacitor of the
LP8556, forms a series RLC circuit. If the output resistance from the source is low enough, the circuit is
underdamped and will have a resonant frequency (typically the case).
– Depending on the size of LS, the resonant frequency could occur below, close to, or above the switching
frequency of the LP8556. This can cause the supply current ripple to be:
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
51
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
Layout Guidelines (continued)
– Approximately equal to the inductor current ripple when the resonant frequency occurs well above the
LP8556 switching frequency.
– Greater than the inductor current ripple when the resonant frequency occurs near the switching
frequency.
– Less than the inductor current ripple when the resonant frequency occurs well below the switching
frequency.
11.2 Layout Examples
CIN
COUT
D1
L1
ISET
FSET
SW
GND
SW
SDA
SCL
SW
GND
SW
PWM
EN
VDDIO
VDD
VBOOST
FSET
LED3
VLDO
ISET
GND
LED2
LED6
LED5
LED4
LED1
CVDD
CVLDO
Figure 28. DSBGA Layout
52
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
LP8556
www.ti.com
SNVS871I – JULY 2012 – REVISED MARCH 2016
Layout Examples (continued)
CIN
COUT
L1
D1
SCL
SDA
GND
_SW
GND
_SW
SW
SW
CVDD
EN/VDDIO
GND
NC
ISET
PWM
VDD
GND
FSET
GND
VBOOST
LED1
VLDO
LED
2
LED
3
GND
LED
4
LED
5
LED
6
ISET
FSET
CVLDO
Figure 29. WQFN Layout
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
53
LP8556
SNVS871I – JULY 2012 – REVISED MARCH 2016
www.ti.com
12 Device and Documentation Support
12.1 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
54
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP8556
PACKAGE OPTION ADDENDUM
www.ti.com
10-Mar-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LP8556SQ-E00/NOPB
ACTIVE
WQFN
RTW
24
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-30 to 85
L8556E0
LP8556SQ-E08/NOPB
ACTIVE
WQFN
RTW
24
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-30 to 85
L8556E8
LP8556SQ-E09/NOPB
ACTIVE
WQFN
RTW
24
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-30 to 85
L8556E9
LP8556SQE-E00/NOPB
ACTIVE
WQFN
RTW
24
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-30 to 85
L8556E0
LP8556SQE-E08/NOPB
ACTIVE
WQFN
RTW
24
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-30 to 85
L8556E8
LP8556SQE-E09/NOPB
ACTIVE
WQFN
RTW
24
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-30 to 85
L8556E9
LP8556SQX-E00/NOPB
ACTIVE
WQFN
RTW
24
4500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-30 to 85
L8556E0
LP8556SQX-E08/NOPB
ACTIVE
WQFN
RTW
24
4500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-30 to 85
L8556E8
LP8556SQX-E09/NOPB
ACTIVE
WQFN
RTW
24
4500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-30 to 85
L8556E9
LP8556TME-E02/NOPB
ACTIVE
DSBGA
YFQ
20
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-30 to 85
56E2
LP8556TME-E03/NOPB
ACTIVE
DSBGA
YFQ
20
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-30 to 85
56E3
LP8556TME-E04/NOPB
ACTIVE
DSBGA
YFQ
20
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-30 to 85
56E4
LP8556TME-E05/NOPB
ACTIVE
DSBGA
YFQ
20
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-30 to 85
56E5
LP8556TME-E06/NOPB
ACTIVE
DSBGA
YFQ
20
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-30 to 85
56E6
LP8556TME-E09/NOPB
ACTIVE
DSBGA
YFQ
20
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-30 to 85
56E9
LP8556TME-E11/NOPB
ACTIVE
DSBGA
YFQ
20
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-30 to 85
6E11
LP8556TMX-E02/NOPB
ACTIVE
DSBGA
YFQ
20
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-30 to 85
56E2
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
10-Mar-2016
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LP8556TMX-E03/NOPB
ACTIVE
DSBGA
YFQ
20
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-30 to 85
56E3
LP8556TMX-E04/NOPB
ACTIVE
DSBGA
YFQ
20
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-30 to 85
56E4
LP8556TMX-E05/NOPB
ACTIVE
DSBGA
YFQ
20
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-30 to 85
56E5
LP8556TMX-E06/NOPB
ACTIVE
DSBGA
YFQ
20
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-30 to 85
56E6
LP8556TMX-E09/NOPB
ACTIVE
DSBGA
YFQ
20
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-30 to 85
56E9
LP8556TMX-E11/NOPB
ACTIVE
DSBGA
YFQ
20
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-30 to 85
6E11
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
10-Mar-2016
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Mar-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LP8556SQ-E00/NOPB
WQFN
RTW
24
1000
178.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
LP8556SQ-E08/NOPB
WQFN
RTW
24
1000
178.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
LP8556SQ-E09/NOPB
WQFN
RTW
24
1000
178.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
LP8556SQE-E00/NOPB
WQFN
RTW
24
250
178.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
LP8556SQE-E08/NOPB
WQFN
RTW
24
250
178.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
LP8556SQE-E09/NOPB
WQFN
RTW
24
250
178.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
LP8556SQX-E00/NOPB
WQFN
RTW
24
4500
330.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
LP8556SQX-E08/NOPB
WQFN
RTW
24
4500
330.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
LP8556SQX-E09/NOPB
WQFN
RTW
24
4500
330.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
LP8556TME-E02/NOPB
DSBGA
YFQ
20
250
178.0
8.4
1.83
2.49
0.76
4.0
8.0
Q1
LP8556TME-E03/NOPB
DSBGA
YFQ
20
250
178.0
8.4
1.83
2.49
0.76
4.0
8.0
Q1
LP8556TME-E04/NOPB
DSBGA
YFQ
20
250
178.0
8.4
1.83
2.49
0.76
4.0
8.0
Q1
LP8556TME-E05/NOPB
DSBGA
YFQ
20
250
178.0
8.4
1.83
2.49
0.76
4.0
8.0
Q1
LP8556TME-E06/NOPB
DSBGA
YFQ
20
250
178.0
8.4
1.83
2.49
0.76
4.0
8.0
Q1
LP8556TME-E09/NOPB
DSBGA
YFQ
20
250
178.0
8.4
1.83
2.49
0.76
4.0
8.0
Q1
LP8556TME-E11/NOPB
DSBGA
YFQ
20
250
178.0
8.4
1.83
2.49
0.76
4.0
8.0
Q1
LP8556TMX-E02/NOPB
DSBGA
YFQ
20
3000
178.0
8.4
1.83
2.49
0.76
4.0
8.0
Q1
LP8556TMX-E03/NOPB
DSBGA
YFQ
20
3000
178.0
8.4
1.83
2.49
0.76
4.0
8.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Mar-2016
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
LP8556TMX-E04/NOPB
DSBGA
YFQ
20
3000
178.0
8.4
LP8556TMX-E05/NOPB
DSBGA
YFQ
20
3000
178.0
8.4
LP8556TMX-E06/NOPB
DSBGA
YFQ
20
3000
178.0
LP8556TMX-E09/NOPB
DSBGA
YFQ
20
3000
178.0
LP8556TMX-E11/NOPB
DSBGA
YFQ
20
3000
178.0
W
Pin1
(mm) Quadrant
1.83
2.49
0.76
4.0
8.0
Q1
1.83
2.49
0.76
4.0
8.0
Q1
8.4
1.83
2.49
0.76
4.0
8.0
Q1
8.4
1.83
2.49
0.76
4.0
8.0
Q1
8.4
1.83
2.49
0.76
4.0
8.0
Q1
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LP8556SQ-E00/NOPB
WQFN
RTW
24
1000
210.0
185.0
35.0
LP8556SQ-E08/NOPB
WQFN
RTW
24
1000
210.0
185.0
35.0
LP8556SQ-E09/NOPB
WQFN
RTW
24
1000
210.0
185.0
35.0
LP8556SQE-E00/NOPB
WQFN
RTW
24
250
210.0
185.0
35.0
LP8556SQE-E08/NOPB
WQFN
RTW
24
250
210.0
185.0
35.0
LP8556SQE-E09/NOPB
WQFN
RTW
24
250
210.0
185.0
35.0
LP8556SQX-E00/NOPB
WQFN
RTW
24
4500
367.0
367.0
35.0
LP8556SQX-E08/NOPB
WQFN
RTW
24
4500
367.0
367.0
35.0
LP8556SQX-E09/NOPB
WQFN
RTW
24
4500
367.0
367.0
35.0
LP8556TME-E02/NOPB
DSBGA
YFQ
20
250
210.0
185.0
35.0
LP8556TME-E03/NOPB
DSBGA
YFQ
20
250
210.0
185.0
35.0
LP8556TME-E04/NOPB
DSBGA
YFQ
20
250
210.0
185.0
35.0
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Mar-2016
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LP8556TME-E05/NOPB
DSBGA
YFQ
20
250
210.0
185.0
35.0
LP8556TME-E06/NOPB
DSBGA
YFQ
20
250
210.0
185.0
35.0
LP8556TME-E09/NOPB
DSBGA
YFQ
20
250
210.0
185.0
35.0
LP8556TME-E11/NOPB
DSBGA
YFQ
20
250
210.0
185.0
35.0
LP8556TMX-E02/NOPB
DSBGA
YFQ
20
3000
210.0
185.0
35.0
LP8556TMX-E03/NOPB
DSBGA
YFQ
20
3000
210.0
185.0
35.0
LP8556TMX-E04/NOPB
DSBGA
YFQ
20
3000
210.0
185.0
35.0
LP8556TMX-E05/NOPB
DSBGA
YFQ
20
3000
210.0
185.0
35.0
LP8556TMX-E06/NOPB
DSBGA
YFQ
20
3000
210.0
185.0
35.0
LP8556TMX-E09/NOPB
DSBGA
YFQ
20
3000
210.0
185.0
35.0
LP8556TMX-E11/NOPB
DSBGA
YFQ
20
3000
210.0
185.0
35.0
Pack Materials-Page 3
MECHANICAL DATA
RTW0024A
SQA24A (Rev B)
www.ti.com
MECHANICAL DATA
YFQ0020xxx
D
0.600±0.075
E
TMD20XXX (Rev D)
D: Max = 2.401 mm, Min =2.341 mm
E: Max = 1.74 mm, Min = 1.68 mm
4215083/A
NOTES:
A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
www.ti.com
12/12
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
Similar pages