Microdc E-XSR Fixed input,isolated regulated dual output dc/dc converter Datasheet

E-XSR Series
FIXED INPUT,ISOLATED&REGULATED Dual Output DC/DC Converter
SELECTION GUIDE
Input
◆
◆
◆
Range
Max
Min
5
4.75-5.25
±5
±100
±10
69
83
E0509XSR
5
4.75-5.25
±9
±56
±6
61
83
E0512XSR
5
4.75-5.25
±12
±42
±5
62
83
E0515XSR
5
4.75-5.25
±15
±33
±4
64
250
E1205XSR
12
11.4-12.6
±5
±100
±10
72
100
Efficiency up to 86%
E1209XSR
12
11.4-12.6
±9
±56
±6
61
83
E1212XSR
12
11.4-12.6
±12
±42
±5
63
83
SIP10 Package
E1215XSR
12
11.4-12.6
±15
±33
±4
64
83
E2405XSR
24
22.8-25.2
±5
±100
±10
72
83
E2409XSR
24
22.8-25.2
±9
±56
±6
60
83
E2412XSR
24
22.8-25.2
±12
±42
±5
63
83
E2415XSR
24
22.8-25.2
±15
±33
±4
64
300
RoHS compliant
Wide temperature performance at full
1 Watt load,-40°C to 85°C
◆
UL 94V-0 package material
◆
No heat sink required
◆
Low ripple and good EMC Features
◆
Industry standard pin out
◆
Power sharing on output
◆
3KVDC isolation
◆
Continuous Short Circuit Protection
◆
Internal SMD construction
NOTICE:add Suffix “P” for Continuous Short Circuit Protection, e.g. E0505XSRRP
ISOLATION SPECIFICATIONS
No external components required
◆
◆
Switching
Frequency
(KHz,Typ)
Nominal
Voltage(VDC)
Current(MA)
Efficiency
(%,Typ)
E0505XSR
FEATURES
◆
Output
Voltage
(VDC)
Order code
Good dynamic feature
Parameter
Test conditions
Min.
Isolation test voltage
Flash tested for 1 minute and 1mA max
3000
Typ.
Max.
Units
VDC
Isolation resistance
Test at Viso=500VDC
1000
MΩ
MODEL SELECTION
①
②
③
④
⑤
⑥
E 05 05 X S R
①Product Series
③Output Voltage
⑤SIP Package
②Input Voltage
④Fixed Input
⑥Regulated output
APPLICATIONS
The E-XSR series are specially designed for
applications where a group of polar power
supplies are isolated from the input power
supply in a distributed power supply system on
a circuit board.
These products apply to:
1) where the voltage of the input power supply
is fixed (voltage variation ≤±5%);
2) where isolation is necessary between input
and output (isolation voltage ≤3000VDC);
3) where the regulation of the output voltage
and the output ripple noise are demanded.
OUTPUT SPECIFICATIONS
Parameter
Test conditions
Output power
Min
Typ.
0.1
Max.
Units
1
W
Line regulation
For Vin change of ±5%
±0.25
%
Load regulation
10% to 100% full load
±1
%
100% full load
±3
%
Output voltage accuracy
Temperature drift
100% full load
0.03
%/°C
10
20
MV p-p
20MHz Bandwidth
50
100
MV p-p
Full load,nominal input
100
Output Ripple*
20MHz Bandwidth
Output Noise*
Switching frequency
Khz
* Test ripple and noise by "parallel cable" method. See detailed operation instructions at Testing of Power
Converter section, application notes.
MICRODC R ESERVES THE COPYRIGHT
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 1 of 2
E-XSR Series
TEMPERATURE CHARACTERISTICS
Parameter
Conditions
Filtering
Min.
Typ.
Storage humidity range
Max.
Units
95
%
Operating temperature
-40
85
°C
Storage temperature
-55
125
°C
30
°C
300
°C
Lead temperature
1.5mm from case for 10 seconds
20
Temp.rise at full load
Cooling
To get an extreme low ripple,an "LC"filtering network
may be connected to the input and output ends of the
DC/DC converter.Which may produce a more significant
filtering effect.It should also be noted that the inductance
and the frequency of the "LC"filtering network should be
staggered with the DC/DC frequency to avoid mutual
interference see (Figure 1).
Free air convection
Case material
Plastic(UL94-V0)
IE-XSP
Short circuit protection
Continuous
1
MTBF
S
3500
K hours
Weight
5.2
g
*Supply voltage must be discontinued at the end of short circuit duration.
TYPICAL CHARACTERISTICS
In some circuits which are sensitive to noise and ripple.a
filtering capacitor may be added to the DC/DC output
end and input end to reduce the noise and ripple.
However, the capacitance of the output filter capacitor
must be proper. If the capacitance is too big, a startup
problem might arise. For every channel of output,
provided the safe and reliable operation is ensured,
the greatest capacitance of its filter capacitor sees
(Table 1).
Temperature Derating Graph
EXTERNAL CAPACITOR TABLE (TABLE 1)
Cin
Vout
Vin
OUTLINE DIMENSIONS & PIN CONNECTIONS
SIZE Graph
(VDC)
5
(μF)
4.7
12
24
-
Cout
(VDC)
±5
(μF)
4.7
2.2
±9
2.2
1.0
±12
1
-
±15
0.47
It's not recommend to connect any external capacitor in
the application field with less than 0.5 watt output.
RECOMMENDED FOOTPRINT
Top view,grid:2.54mm(0.1inch)
diameter:1.00mm(0.039inch)
Overload Protection
Under normal operating conditions, the output circuit
of these products has no protection against over-current
and short-circuits.The simplest method is to connect a
self-recovery fuse in series at the input end or add a
circuit breaker to the circuit.
FOOTPRINT DETAILS
Note:
Unit:mm(inch)
Pin section:0.50*0.3mm(0.020*0.012inch)
Pin section tolerances:±0.10mm(±0.004inch)
General tolerances:±0.25mm(±0.010inch)
Pin
Function
1
VIN
2
GND
7
+V0
9
-V0
10
0V
When the environment temperature is higher than
71℃, the product output power should be less then
60% of the rated power.
No parallel connection or plug and play.
All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise
specified.Another 24V products, please inquire Our technical department!
Requirement on output load
To ensure this module can operate efficiently and reliably, a minimum load is specified for this kind of
DC/DC converter in addition to a maximum load(namely full load).During operation, make sure the
specified range of input voltage is not exceeded,the minimum output load is not less than 10% of the full
load, and that this product should never be operated under no load!
Use dual output simultaneously, forbid opening
output pin (0V) to use as single output.
RoHS COMPLIANT INFORMATION
Microdc Professional Power Module,Inc.
Tel:0086-20-86000646
E-mail:[email protected]
Website:http://www.microdc.cn
This series is compatible with RoHS soldering systems with a peak wave solder temperature
of 300°C for 10 seconds.
The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin
with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this
series are backward compatible with Sn/Pb soldering systems.
REACH COMPLIANT INFORMATION
This series has proven that this product does not contain harmful chemicals, it also has
harmful chemical substances through the registration, inspection and approval.
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 2 of 2
Similar pages