CITIZEN CLC032-069A5-313H3H3-185 This product (cob) is comprised of two different ccts, and is to be driven using the 2 terminals which are shown in page 5 Datasheet

CITILED COB+ Series
DATA SHEET
CLC032-069A5
Introduction
P 2
Performance Characteristics
P 3
Mechanical Dimensions
P 5
Characteristic Curves
P 6
Reliability
P 9
6.
Packing Specification
P 10
7.
Precaution
P 11
8.
Warranty
P 14
9.
Action for failed product
P 14
10. Others
P 14
11. Use of this product
P 15
1
Ref.CE-P3414 04/16
Product Nomenclature
CLC032 - 069 A5 - 31 3 H3 H3 - 185
[1]
[2]
[3]
[4]
[5]
[1]
Product shape
CLC032
[2]
Die count
69
[3]
Cool CCT
3100K
[4]
Chromaticity range
MacAdam 3step *1
[5]
CRI (Ra)
Min.90
[6]
Warm CCT
1850K
[6]
1. Introduction
1-1. Product Description
This product (COB) is comprised of two different CCTs, and is to be driven using the 2 terminals
which are shown in Page 5.
1-2. Features
・Mechanical Dimensions
・Package Structure
・Ceramic Base:
・Connection to Heat Sink
・CRI (Ra)
・Cool CCT
・Warm CCT
・Chromaticity Range
・Thermal Resistance
・RoHS compliant
:
:
:
:
:
:
:
:
:
19.0 x 26.0 x 1.6 (mm)
Ceramic Base Chip on Board
material AZ214T(Certificate Number 20140905-E356524)
By Holder + M3screw, Thermally conductive glue
Min.90
3,100K (IF=240mA)
1,850K (IF=10mA)
3-step MacAdam Ellipse, the center refers to ANSI C78.377:2011. *1
2.0C/W
*1 It applies only to cool CCT.
2
Ref.CE-P3414 04/16
2. Performance Characteristics
2-1. Electro Optical Characteristics
(Tc=25C )
Product cord
CLC032-069A5-313H3H3-185
Nominal
CCT
CRI (Ra)
Chromaticity
Luminous flux
( lm )
Ra
R9
x
y
Min
Min
Min.
Typ.
Max.
Typ
Typ
3100K
90
50
820
940
-
0.430
0.402
1850K
90
50
13
23
-
0.544
0.410
Voltage
(V)
Forward
Current
(mA)
Thermal
Resistance
Rj-c
( C/W )
Min.
Typ.
Max.
240.0
31.4
34.1
36.8
2.0
10.0
24.8
27.0
29.2
2.0
Notes :
1. The tolerance of measurement at our tester is forward voltage +/-3%, Φv+/-10% , Chromaticity(x,y)+/-0.005 and Ra+/-1.
2-2. Absolute Maximum Ratings
Parameter
Symbol
Rating
Input Power [W]
Forward Current [mA]
Minimum Current [mA]
Reverse Current [mA]
Operating Temperature [C]
Storage Temperature [C]
Case Temperature [C]
Junction Temperature [C]
Pi
IF
IF min
Ir
Top
Tst
Tc
Tj
22.1
*1
600.0
*1
8
1
-30 ~ +85
-40 ~ +100
95
*2
150
*3
*1. Input power and forward current are the values when the LED is used within the range of the derating
characteristics in this data sheet.
*2 Refer to 3. Mechanical Dimensions for Tc measurement point
*3 Tj = Tc + Rj-c x Pi
3
Ref.CE-P3414 04/16
2-3. Chromaticity Characteristics
( Tc=25C )
Oval parameter
Color Region
Nominal
CCT
Center Point
( x, y )
3-step MacAdam ellipse
3100K
5-step MacAdam ellipse
1850K
Major Axis
a
Minor Axis
b
( 0.4301 , 0.4016 )
0.00834
0.00408
Ellipse
Rotation Angle
θ
53.17
( 0.5436 , 0.4098 )
0.0129
0.00685
57.28
* Color region stays within MacAdam 3-step ellipse from the chromaticity center.
* θ is the angle between the major axis of the ellipse and the x-axis, and a and b are the major and minor semi-axes of an ellipse.
(Ref. IEC 60081:1997 AnnexD)
Color region
0.46
1,850K
y
3,100K
0.41
Center point
3100K(3SDCM)
B.B. Locus
0.36
0.40
0.45
0.50
0.55
x
4
Ref.CE-P3414 04/16
3. Mechanical Dimensions
Unit : mm
Tolerances unless otherwise specified : +/-0.3
Marking 1 : Serial No.
Marking 2 : *** ** * **
Warm CCT
CRI
Cool CCT
Circuit diagram
Product Series
5
Ref.CE-P3414 04/16
4. Characteristic Curves
4-1. Forward Current Characteristics / Temperature Characteristics
Forward Current vs. Forward Voltage
Forward Current vs. Relative Luminous Flux
Tc=25C
45
Tc=25C
250%
Relative Luminous Flux [a.u.]
Forward Voltage [V]
40
35
30
25
20
15
10
5
0
200%
150%
100%
50%
0%
0
100
200
300
400
Forward Current [mA]
500
600
0
Forward Current vs. CCT
100
200
300
400
Forward Current [mA]
500
600
xy Chromaticity profile
Tc=25C
Tc=25C
3500
0.46
3000
0.44
2000
0.42
y
CCT [K]
2500
1500
0.4
(100mA)
1000
(10mA)
(240mA)
500
0.38
0
0
100
200
300
400
Forward current [mA]
500
600
0.36
0.4
0.44
0.48
0.52
0.56
x
Case Temperature vs. Relative Forward Voltage
Case Temperature vs. Ralative Luminous Flux
120%
Relative Luminous Flux [a.u.]
Relative Forward Voltage [a.u.]
110%
105%
(10mA)
100%
95%
(240mA)
90%
85%
80%
(10mA)
100%
(240mA)
80%
60%
25
45
65
Tc [C]
85
105
25
45
65
Tc [C]
85
105
* Characteristics data shown here are for reference purpose only. (Not fuaranteed data)
6
Ref.CE-P3414 04/16
4-2. Optical Characteristics
Spectrum
3100K(IF=240mA)
1850K(IF=10mA)
Tc=25℃
100%
90%
Radiative Intensity [a.u.]
80%
70%
60%
50%
40%
30%
20%
10%
0%
380
430
480
530
580
630
Wave length [nm]
680
730
780
Radiation Characteristic
IF=240mA
-40°
-50°
-60°
-70°
-30°
-20° -10°
100%
10°
20°
30°
40°
50°
80%
60%
60°
40%
70°
Y
X
-80°
-90°
20%
80°
Y
90°
0%
7
Ref.CE-P3414 04/16
X
4-2. Optical Characteristics (continued)
IF=10mA
-40°
-30°
-20° -10°
10°
100%
-50°
20°
30°
40°
50°
80%
-60°
-70°
60%
60°
40%
70°
X
20%
-80°
80°
Y
-90°
90°
0%
4-3. Derating Characteristics
Case Temperature vs. Allowable Forward Current
700
Forward current [mA]
600
500
400
300
200
100
0
25
45
65
85
105
125
Tc [C]
8
Ref.CE-P3414 04/16
5. Reliability
5-1. Reliability Test
Test Item
Test Condition
Continuous Operation Test
IF =240mA , Tc=95C
Low Temperature Storage Test
Ta = -40 C × 1000 hours
High Temperature Storage Test
Ta = 100 C × 1000 hours
Moisture-proof Test
Tc=95C, 95 %RH for 500 hours
Thermal Shock Test
-30 C × 30 minutes – 85 C × 30 minutes, 100 cycle
5-2. Failure Criteria
( Tc=25C )
Measuring Item
Symbol
Measuring Condition
Failure Criteria
Power Dissipation
VF
IF =240mA
>U × 1.2
Total Luminous Flux
Φv
IF =240mA
<S × 0.8
U defines the upper limit of the specified characteristics. S defines the initial value.
Note : Measurement shall be taken between 2 hours and 24 hours, and the test pieces should be
return to the normal ambient conditions after the completion of each test.
9
Ref.CE-P3414 04/16
6. Packing Specification
6-1. Packing
An empty tray is placed on top of a 6-tier tray which contain 40 pieces each.
(Smallest packing unit: 240 pieces)
A label with product name, quantity and lot number is placed on the upper empty tray.
Tray (Dimensions: 310 x 210 x 12 mm / Materials: Electrically conductive PS)
12mm
Unit : mm
210mm
310mm
Product 40 pcs/tray
Example of indication label
1. TYPE
CUSTOMER
2. P.No. ( Cutomer's P/N )
TYPE : CLC***-******-******* ---(1)
P. NO : ******
---(2)
Lot No: *******
---(3)
Q'ty : ***
---(4)
3. Lot No.
e.g. CLC032-069A5-313H3H3-185
- First and second letter: Last digit of the year
- Third letter: Production month
PASS
e.g. 15 : year 2015
e.g. 1 : January
Note: October, November and December are designated X,Y and Z.
- Forth letter: CE's control number
e.g. 5035
4. Quantity
10
Ref.CE-P3414 04/16
7. Precaution
7-1. Handling with care for this product
-Both the light emitting area and white dam over the light emitting area is composed of resin materials.
Please avoid the resin area from being pressed, stressed, rubbed, come into contact with sharp metal nail
(e.g. edge of reflector part) because the function, performance and reliability of this product
are negatively impacted.
-Please be aware that this product should not come into contact with any other parts
while incorporating in your lighting apparatus or your other products.
7-2. Countermeasure against static electricity
-Handling of this product needs countermeasures against static electricity
because this is a semiconductor product.
-Please take adequate measures to prevent any static electricity being produced
such as the wearing of a wristband or anti-static gloves when handling this product.
-Every manufacturing facility in regard to the product (plant, equipment, machine, carrier machine
and conveyance unit) should be connected to ground and please avoid the product to be electric-charged.
7-3. Caution of product assembly
-Regarding this product assembling on the heat sink, it is recommended to use thermal conductivity
glue or grease, and please optimize the assembly conditions according to
the specifications of the thermal conductivity glue or grease.
Please don't fix this product on Heat sink by screw directly to prevent breaking ceramic substrate.
In addition, please don’t press with excess stress on the product while the assembly.
And, the surfaces of thermal conductivity glue or grease, should be kept clean,
therefore please remove pollution, fluid and oil on the surfaces.
-Roughness, unevenness and burr of surface negatively impact thermal bonding
between the product and heat sink and increase heat thermal resistance between them.
Confidence of thermally and mechanical coupling between the product and heat sink might be confirmed
by checking the mounting surface and measuring the case temperature of the product.
-Heat sink should be covered under the yellow resin area locating on the side of center light emitting area
because it generates heat as same as emitting area.
11
Ref.CE-P3414 04/16
7-4. Thermal Design
-The thermal design to draw heat away from the LED junction is most critical parameter
for an LED illumination system. High operating temperatures at the LED junction adversely affect
the performance of LED’s light output and lifetime. Therefore the LED junction temperature should
not exceed the absolute maximum rating in LED illumination system.
-The LED junction temperature while operation of LED illumination system depends upon
thermal resistance of internal LED package (Rj-c), outer thermal resistances of LED package,
power loss and ambient temperature. Please take both of the thermal design specifications
and ambient temperature conditions into consideration for the setting of driving conditions.
-For more information, please refer to application note "Thermal Management".
7-5. Driving Current
-A constant current is required as an applying driving current to this product.
-Electrical transient might apply excess voltage, excess current and reverse voltage to the product(s).
They also affect negative impact on the product(s) therefore please make sure that no excess voltage,
excess current and reverse voltage is applied to the product(s) .
-Please verify that the selected driver and dimmer switch can drive CLC032 correctly.
7-6. Electrical Safety
-This product itself is designed to cover UL requirements that may apply on the final product. however,
the UL certification still needs to be granted as the final product level which is depending on the design structure,
materials used and how the LED is placed and fixed in the final product. Therefore please confirm electrical safety
and dielectric in final product.
-Component failures can be caused by excessive voltage.
-Discharge before handling this product.
-ESD sensitivity of this product is over 1000V (based on IEC61000-4-2).
12
Ref.CE-P3414 04/16
7-7. Recommended soldering Condition (This product is not adaptable to reflow process.)
-For manual soldering
Please use lead-free soldering. Soldering shall be implemented using a soldering bit at a temperature lower than 380C,
and shall be finished within 5 seconds for one land.
No external force shall be applied to resin part while soldering is implemented.
Next process of soldering should be carried out after the product has return to ambient temperature.
-For soldering correction
Regarding soldering correction, above conditions shall be applied.
Contacts number of soldering bit should be within twice for each terminal as a correction.
* Citizen Electronics cannot guarantee if usage exceeds these recommended conditions.
Please use it after sufficient verification is carried out on your own risk if absolutely necessary.
7-8. Eye Safety
-The International Electrical Commission (IEC) published in 2006 IEC 62471
”2006 Photobiological safety of lamps and lamp systems ” which includes LEDs within its scope.
When sorting single LEDs according to IEC 62471, almost all white LEDs can be classified
as belonging to either Exempt Group (no hazard) or Risk Group 1 (low risk).
-However, Optical characteristics of LEDs such as radiant flux,
spectrum and light distribution are factors that affect the risk group determination of the LED,
and especially a high-power LED, that emits light containing blue wavelengths,
might have properties equivalent to those of Risk Group 2 (moderate risk).
-Great care should be taken when directly viewing an LED that is driven at high current,
has multiple uses as a module or when focusing the light with optical instruments,
as these actions might greatly increase the hazard to your eyes.
-It is recommended to regard the evaluation of stand-alone LED packages as a reference
and to evaluate your final product.
7-9. This product is not designed for usage under the following conditions.
If the product might be used under the following conditions, you shall evaluate its effect
and appropriate them. In places where the product might:
-directly and indirectly get wet due to rain and/or at place with the fear.
-be damaged by seawater and/or at place with the fear
-be exposed to corrosive gas (such as Cl2, H2S, NH3, SOx, NOx and so on) and/or at place with the fear.
-be exposed to dust, fluid or oil and/or at place with the fear.
-be put in the enclosed space with halogenated substance and/or gas (such as Br, Cl and so on).
13
Ref.CE-P3414 04/16
8. Warranty
(1) CITIZEN ELECTRONICS guarantees the term of the reliability test results and elementary
substances of the supplies to be within the set conditions.
Please note that any accident/damage that occurs during or because of usage that deviates
from the conditions contained in the specifications are not warrantable.
(2) Although CITIZEN ELECTRONICS will deliver products of quality assured by the terms included
in these specifications, incorporation in actual machines, lifetime in actual use
and another quality shall be confirmed sufficiently by customers.
Customers are responsible for ensuring quality and to meet the specifications such as with
regard to the security / the performance to standards of safety / reliability of the finished product.
(3) The use of this product is intended for use in general electronics such as business machines,
communication equipment, audio-visual equipment, household electrical appliances and measurement devices, etc.
(4) If this product is considered to be used in applications where high reliability is required and
failure or malfunction have a direct influence on human life or health such as aerospace instrument,
medical equipment, atomic energy control devices and so on, please contact Citizen Electronics beforehand.
9. Action for failed product
(1) If a failed product is found, action shall be taken after consultation between both sides.
However, in cases where it is obvious that the relevant failed product is attributed to
CITIZEN ELECTRONICS, action will be limited to product replacement delivery.
(2) When a failed product is returned, the failure phenomenon should be specified in writing and attached.
CITIZEN ELECTRONICS will review the condition promptly and report the result to the customer.
10. Others
(1) All matters of this product's quality with regard to the customer are mentioned in these specifications,
and any matters which are not mentioned in these specifications in items stated prior to receipt shall lose efficacy.
(2) When a question occurs about the contents of these specifications, please contact
CITIZEN ELECTRONICS.
In addition, if there is any discrepancy in the contents of these specifications, both sides shall handle
the matter with gentlemanlike discussion.
(3) Please do not conduct any actions equal to reverse-engineering such as the disassembling or
the analysis of this product without CITIZEN's permission.
Please contact CITIZEN directly without disassembling in any way if a failure is found in this product.
(4) If this product is not returned within three weeks after this specification has been published,
it is judged that the contents have been accepted.
CITIZEN Micro HumanTech is a registered trademark of Citizen Holding Co., Japan.
CITILED is a registered trademark of CITIZEN ELECTRONICS CO., LTD. Japan
14
Ref.CE-P3414 04/16
11. Use of this product
(1) This document is provided for reference purposes only so that CITIZEN ELECTRONICS' products are used as
intended. CITIZEN ELECTRONICS neither makes warranties or representations with respect to the accuracy or
completeness of the information contained in this document nor grants any license to any intellectual property rights or any
other rights of CITIZEN ELECTRONICS or any third party with respect to the information in this document.
(2) All information included in this document such as product data, diagrams, charts, is current as of the date this document
is issued.
Such information, however, is subject to change without any prior notice.
Before purchasing or using any CITIZEN ELECTRONICS' products listed in this document, please confirm the latest
product information with a CITIZEN ELECTRONICS' sales office, and formal specifications must be exchanged and
signed by both parties prior to mass production.
(3) CITIZEN ELECTRONICS has used reasonable care in compiling the information included in this document, but
CITIZEN ELECTRONICS assumes no liability whatsoever for any damages incurred as a result of errors or omissions in
the information included in this document.
(4) Absent a written signed agreement, except as provided in the relevant terms and conditions of sale for product, and to
the maximum extent allowable by law, CITIZEN ELECTRONICS assumes no liability whatsoever, including without
limitation, indirect, consequential, special, or incidental damages or loss, including without limitation, loss of profits, loss
of opportunities, business interruption and loss of data, and disclaims any and all express or implied warranties and
conditions related to sale, use of product, or information, including warranties or conditions of merchantability, fitness for
a particular purpose, accuracy of information, or no infringement.
(5) Though CITIZEN ELECTRONICS works continually to improve products' quality and reliability, products can
malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and
safeguards to minimize risk and avoid situations in which a malfunction or failure of a product could cause loss of human
life, bodily injury or damage to property, including data loss or corruption.
In addition, customers are also responsible for determining the appropriateness of use of any information contained in this
document such as application cases not only with evaluating by their own but also by the entire system.
CITIZEN ELECTRONICS assumes no liability for customers' product design or applications.
(6) Please contact CITIZEN ELECTRONICS' sales office if you have any questions regarding the information contained in
this document, or if you have any other inquiries.
CITIZEN Micro HumanTech is a registered trademark of Citizen Holding Co., Japan.
CITILED is a registered trademark of CITIZEN ELECTRONICS CO., LTD. Japan
15
Ref.CE-P3414 04/16
and
are trademarks or registered trademarks of CITIZEN HOLDINGS CO., LTD. JAPAN.
is a trademark or a registered trademark of CITIZEN ELECTRONICS CO., LTD. JAPAN.
16
Ref.CE-P3414 04/16
Similar pages