UN JK250-1200U Radial lead resettable polymer ptc Datasheet

Radial Lead Resettable Polymer PTCs
JK250 Series
Description
JK250 Series is designed to protect against short duration
high voltage fault currents (power cross or power induction
surge) typically used in AC220V.
Features
u
u
u
u
0.02-2.0A hold current rating
250VAC operating voltage
Fast time-to- trip
RoHS compliant, Lead-Free and Halogen-Free
Applicable
u
u
u
AC220V over-current protection
Power ports
Customer Premises Equipment(CPE)
Electrical Parameters
Maximum Time
To Trip
Current
Time
(A)
(Sec.)
V max
(Vac)
I max
(A)
P dtyp.
(W)
0.045
250
3.0
1.0
1.0
0.030
0.065
250
3.0
1.0
JK250-040U
0.040
0.080
250
3.0
JK250-060U
0.060
0.120
250
JK250-080U
0.080
0.160
JK250-090U
0.090
JK250-100U
Part Number
I hold (A)
JK250-020U
0.020
JK250-030U
I trip
(A)
Resistance
R min
(Ω)
R max
(Ω)
R 1max
(Ω)
0.10
80.0
160.0
240.0
1.0
0.10
60.0
120.0
180.0
1.0
0.5
1.00
30.0
60.0
80.0
3.0
1.0
0.5
2.00
22.0
40.0
60.0
250
3.0
1.0
1.0
0.25
14.0
22.0
33.0
0.180
250
3.0
1.0
1.0
0.50
10.0
20.0
31.0
0.100
0.200
250
3.0
1.0
1.0
1.00
10.0
20.0
31.0
JK250-110U
0.110
0.220
250
3.0
1.0
1.0
1.20
6.0
12.0
16.0
JK250-120U
0.120
0.240
250
3.0
1.0
1.0
1.20
6.0
11.0
16.0
JK250-145U
0.145
0.290
250
3.0
1.0
1.0
4.00
3.5
6.5
14.0
JK250-180T
0.180
0.540
250
10.0
1.8
3.0
1.50
1.0
2.2
4.0
JK250-180U
0.180
0.540
250
10.0
1.8
3.0
1.50
1.0
3.0
5.0
JK250-200U
0.200
0.400
250
10.0
2.4
3.0
5.00
3.0
6.0
9.0
JK250-400U
0.400
0.800
250
10.0
2.8
3.0
8.0
1.0
3.0
6.0
JK250-600U
0.600
1.200
250
10.0
3.2
3.0
12.0
0.6
2.00
5.0
JK250-800U
0.800
1.600
250
10.0
3.6
4.0
18.0
0.40
1.00
3.0
JK250-1000U
1.000
2.000
250
10.0
3.6
5.0
20.0
0.50
0.80
2.0
JK250-1200U
1.200
2.400
250
10.0
3.6
6.0
20.0
0.20
0.80
2.0
JK250-1500U
1.500
3.000
250
10.0
4.8
7.5
20.0
0.20
0.60
1.5
JK250-2000U
2.000
4.000
250
10.0
4.8
10.0
20.0
0.20
0.40
1.5
UN Semiconductor Co., Ltd.
Revision October 18, 2013
www.unsemi.com.tw
1/4
@ UN Semiconductor Co., Ltd. 2013
Specifications are subject to change without notice.
Please refer to www.unsemi.com.tw for current information.
Radial Lead Resettable Polymer PTCs
JK250 Series
I hold= Hold current: maximum current device will pass without tripping in 25°C still air.
I trip= Trip current: minimum current at which the device will trip in 25°C still air.
V max= Maximum voltage device can withstand without damage at rated current (Imax)
I max= Maximum fault current device can withstand without damage at rated voltage (Vmax)
Pdtyp.= Power dissipated from device when in the tripped state at 25°C still air.
R min= Minimum resistance of device in initial (un-soldered) state.
R max= Maximum resistance of device in initial (un-soldered) state.
R 1max= Maximum resistance of device at 25°C measured one hour after tripping.
Caution: Operation beyond the specified rating may result in damage and possible arcing and flame.
0.48
0.25
Temperature Rerating Chart – I hold (A)
Ambient Operation Temperature
Part Number
-40°C
-20°C
0°C
25°C
JK250-020U
JK250-030U
JK250-040U
JK250-060U
JK250-080U
JK250-090U
JK250-100U
JK250-110U
JK250-120U
JK250-145U
JK250-180T
JK250-180U
JK250-200U
JK250-400U
JK250-600U
JK250-800U
JK250-1000U
JK250-1200U
JK250-1500U
JK250-2000U
0.031
0.047
0.062
0.093
0.124
0.140
0.155
0.171
0.186
0.230
0.280
0.280
0.310
0.620
0.930
1.240
1.550
1.860
2.330
3.100
0.027
0.041
0.055
0.082
0.110
0.119
0.137
0.145
0.164
0.191
0.238
0.238
0.274
0.550
0.820
1.100
1.370
1.650
2.100
2.740
0.024
0.036
0.048
0.070
0.095
0.105
0.119
0.129
0.143
0.170
0.211
0.211
0.238
0.480
0.710
0.950
1.190
1.430
1.650
2.380
0.020
0.030
0.040
0.060
0.080
0.090
0.100
0.110
0.120
0.145
0.180
0.180
0.200
0.400
0.600
0.800
1.000
1.200
1.500
2.000
40°C
50°C
60°C
70°C
85°C
0.015
0.022
0.029
0.044
0.058
0.069
0.077
0.085
0.088
0.112
0.139
0.139
0.146
0.290
0.440
0.580
0.730
0.900
1.130
1.460
0.013
0.019
0.026
0.038
0.051
0.061
0.068
0.075
0.077
0.099
0.122
0.122
0.128
0.260
0.380
0.510
0.640
0.816
1.020
1.280
0.011
0.017
0.022
0.033
0.044
0.055
0.61
0.067
0.066
0.088
0.110
0.110
0.110
0.22
0.33
0.44
0.55
0.732
0.915
1.10
0.008
0.012
0.016
0.025
0.033
0.043
0.045
0.053
0.049
0.070
0.086
0.086
0.082
0.160
0.250
0.330
0.410
0.564
0.705
0.820
Hold Current (A)
0.016
0.025
0.033
0.049
0.066
0.077
0.085
0.094
0.098
0.123
0.153
0.153
0.164
0.330
0.490
0.660
0.820
1.020
1.280
1.640
Temperature Rerating Curve
Time in Seconds
Percentage of Rated Current
Average Time Current Curves
Temperature (°C)
Current in Amperes
Test Procedures and Requirement
UN Semiconductor Co., Ltd.
Revision October 18, 2013
www.unsemi.com.tw
2/4
@ UN Semiconductor Co., Ltd. 2013
Specifications are subject to change without notice.
Please refer to www.unsemi.com.tw for current information.
Radial Lead Resettable Polymer PTCs
JK250 Series
Test
Test Conditions
Accept/Reject Criteria
Resistance
In still air @25±2°C
Rmin≤R≤Rmax
Hold Current
60 min, at Ihold, In still air @25±2°C
No trip
Time to Trip
Specified current, Vmax, @25±2°C
T≤Maximum Time To Trip
Trip Cycle Life
Vmax, Imax,100 cycles
No arcing or burning
Trip Endurance
Vmax,24hours
No arcing or burning
Soldering Parameters
Pre-Heating Zone
Refer to the condition recommended
by the manufacturer. Max. ramping
rate should not exceed 4°C/Sec
Soldering Zone
Max. solder temperature should not
exceed 260°C
Cooling Zone
Cooling by natural convection in air
Physical Specifications
Lead Material
Soldering
Characteristics
Insulating Material
Device Labeling
0.02-0.04A Tin-plated Copper clad steel
0.05-2.00A Tin-plated Copper
Solder ability per MIL-STD-202, Method 208E
Cured, flame retardant epoxy polymer meets UL 94V-0
requirements.
Marked with ‘SC’, voltage, current rating
Dimensions
Figure1
Part Number
Figure
Figure2
Figure3
Figure4
A
B
C
D
Lead (dia)
mm
Max.
mm
Max.
mm
Typ.
mm
Max.
Inches
mm
(Bulk Pack)
Packaging
JK250-020U
Figure1(2)
7.4
12.7
5.1
3.8
0.020
0.5
1000
JK250-030U
Figure1(2)
7.4
12.7
5.1
3.8
0.020
0.5
1000
JK250-040U
Figure1(2)
7.4
12.7
5.1
3.8
0.020
0.5
1000
JK250-060U
Figure1(2)
7.4
12.7
5.1
3.8
0.024
0.6
1000
UN Semiconductor Co., Ltd.
Revision October 18, 2013
www.unsemi.com.tw
3/4
@ UN Semiconductor Co., Ltd. 2013
Specifications are subject to change without notice.
Please refer to www.unsemi.com.tw for current information.
Radial Lead Resettable Polymer PTCs
JK250 Series
JK250-080U
Figure1
7.4
12.7
5.1
3.8
0.024
0.6
1000
JK250-090U
Figure1
7.4
12.7
5.1
3.8
0.024
0.6
1000
JK250-100U
Figure1
7.8
12.0
5.1
3.8
0.024
0.6
1000
JK250-110U
Figure3
7.0
12.6
5.1
3.8
0.024
0.6
1000
JK250-120U
Figure3
7.0
10.0
5.1
3.8
0.024
0.6
1000
JK250-145U
Figure3
7.0
10.0
5.1
3.8
0.024
0.6
1000
JK250-180T
Figure1
10.2
14.5
5.1
3.4
0.024
0.6
1000
JK250-180U
Figure3
11.2
14.5
5.1
3.8
0.024
0.6
1000
JK250-200U
Figure4
10.5
17.0
5.1
3.8
0.024
0.6
1000
JK250-400U
Figure4
10.5
17.0
5.1
3.8
0.031
0.8
1000
JK250-600U
Figure4
16.0
18.0
5.1
4.5
0.031
0.8
500
JK250-800U
Figure4
20.0
22.0
5.1
4.5
0.031
0.8
500
JK250-1000U
Figure4
20.0
22.0
5.1
4.5
0.031
0.8
200
JK250-1200U
Figure4
22.0
28.0
5.1
4.5
0.031
0.8
200
JK250-1500U
Figure4
25.0
30.0
5.1
4.5
0.031
0.8
200
JK250-2000U
Figure4
26.0
32.0
5.1
4.5
0.031
0.8
200
Warning
u This product should not be used in an application where the maximum interrupt voltage or maximum interrupt current in a
fault condition, Operation beyond the maximum rating or improper use may result in device damage and possible electrical
arcing and flame.
u A PPTC device is not a fuse, It is a nonlinear thermistor that limits current, Because under a fault condition all PPTC devices
go into a high resistance state but not open circuit hazardous voltage may be present at PPTC.
u The devices are intended for protection against occasional over-current or over-temperature fault conditions and should not
be used when repeated fault conditions or prolonged trip events.
u In most application, power must be removed and the fault condition cleared in order to reset a PPTC device.
u PPTC devices are not recommended to be installed in applications where the device is constrained such that its PPTC
properties are inhibited, for example in rigid potting materials or Add devices surface coating, Bundled devices ontology,
which lack adequate clearance to accommodate device expansion.
u Contamination on of the PPTC material with certain silicone-based oils or some aggressive solvents can adversely impact the
performance of the devices. For example, Organic solvents to cleaning.
UN Semiconductor Co., Ltd.
Revision October 18, 2013
www.unsemi.com.tw
4/4
@ UN Semiconductor Co., Ltd. 2013
Specifications are subject to change without notice.
Please refer to www.unsemi.com.tw for current information.
Similar pages