E M C C o m p o n e n t s February 2015 Chip Beads For general signal line MMZ Series MMZ0402 Type MMZ0402 0402[01005 inch]* * Dimensions Code JIS[EIA] (2/10) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20150203 / beads_commercial_signal_mmz0402_en.fm (3/10) E M C C o m p o n e n t s Chip Beads Product compatible with RoHS directive Halogen-free Compatible with lead-free solders For general signal line Overview of MMZ0402 Type FEATURES Noise reduction solution for general signal line. Various frequency characteristics with 8 materials of different features for countermeasures against everything from general signals to high-speed signals. APPLICATION Noise removal for mobile devices such as smartphones and tablet terminals, and various modules. Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment. PART NUMBER CONSTRUCTION MMZ Series name 0402 L×W×T Dimensions (mm) 0402 0.4×0.2x0.2 S Material name D S Y 100 C Impedance (:) at 100MHz 100 10 121 120 Characteristic type C T 000 Packaging style Internal code T Taping 000 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Operating Storage Type temperature temperature （°C） （°C） MMZ0402 –55 to +125 –55 to +125 The Storage temperature range is for after the circuit board is mounted. Package quantity Individual weight (pieces/reel) 20,000 （mg） 0.08 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150203 / beads_commercial_signal_mmz0402_en.fm (4/10) E M C C o m p o n e n t s MMZ0402 Type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150°C 180°C Time t1 60 to 120s Soldering Temp. Time T3 t2 230°C 30 to 60s Peak Temp. T4 250 to 260°C Time t3 10s Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150203 / beads_commercial_signal_mmz0402_en.fm (5/10) E M C C o m p o n e n t s MMZ0402 Type MATERIAL CHARACTERISTICS S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz. Y material: High frequency range type intended for the 100MHz region and above. For signal line applications in which the signal frequency is far from the cutoff frequency. Impedance values selected for effectiveness at 80 to 400MHz. D material: For applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequencies. Designed for high impedance at high frequencies (300MHz to 1GHz) for signal line applications. TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS 500 400 S D 300 Y 200 100 0 10 100 1000 Frequency(MHz) 1000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150203 / beads_commercial_signal_mmz0402_en.fm (6/10) E M C C o m p o n e n t s MMZ0402 Type SHAPE & DIMENSIONS 0.2±0.02 0.2±0.02 0.4±0.02 Dimensions in mm 0.08 to 0.14 0.18 to 0.2 RECOMMENDED LAND PATTERN 0.15 to 0.2 0.2 0.15 to 0.2 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150203 / beads_commercial_signal_mmz0402_en.fm (7/10) E M C C o m p o n e n t s MMZ0402 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance [100MHz] (: ) 10 70 120 150 240 75 22 Tolerance ±5: ±25% ±25% ±25% ±25% ±25% ±25% DC resistance Rated current Part No. (: )max. 0.07 0.36 0.70 0.70 1.00 0.70 0.70 (mA)max. 750 300 210 200 200 250 250 MMZ0402S100CT000 MMZ0402S700CT000 MMZ0402S121CT000 MMZ0402S151CT000 MMZ0402S241CT000 MMZ0402Y750CT000 MMZ0402D220CT000 ○ Measurement equipment Measurement item Product No. Impedance E4991A+16196D DC resistance Type-7556 ＊ Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Yokogawa Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150203 / beads_commercial_signal_mmz0402_en.fm (8/10) E M C C o m p o n e n t s MMZ0402 Type ELECTRICAL CHARACTERISTICS Z VS. FREQUENCY CHARACTERISTICS (BY SERIES) MMZ0402S SERIES MMZ0402Y SERIES MMZ0402D SERIES 300 500 MMZ0402S241C 300 250 250 400 MMZ0402D220C 300 MMZ0402S151C 200 MMZ0402S121C 100 MMZ0402S700C MMZ0402S100C 0 200 150 100 50 0 1 10 100 1000 Frequency (MHz) 10000 Impedance (Ω) Impedance (Ω) Impedance (Ω) MMZ0402Y750C 200 150 100 50 1 10 100 1000 Frequency (MHz) 10000 0 1 10 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150203 / beads_commercial_signal_mmz0402_en.fm (9/10) E M C C o m p o n e n t s MMZ0402 Type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS MMZ0402S100CT000 MMZ0402S700CT000 R 10 5 X 1 10 100 1000 Frequency (MHz) 10000 300 500 250 400 200 Z R 150 100 50 0 X 1 10 R X 1 10 100 1000 Frequency (MHz) 100 1000 Frequency (MHz) 10000 Z 150 R 100 50 X 1 10 100 1000 Frequency (MHz) 10000 MMZ0402Y750CT000 300 Z 300 R 200 100 0 200 0 10000 MMZ0402S241CT000 Impedance (Ω) Impedance (Ω) MMZ0402S151CT000 Z Impedance (Ω) 0 250 Impedance (Ω) 15 Z 160 140 120 100 80 60 40 20 0 Impedance (Ω) Impedance (Ω) 20 MMZ0402S121CT000 X 1 10 100 1000 Frequency (MHz) 10000 250 200 Z 150 R 100 50 0 X 1 10 100 1000 Frequency (MHz) 10000 MMZ0402D220CT000 Impedance (Ω) 300 250 200 Z 150 R 100 X 50 0 1 10 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150203 / beads_commercial_signal_mmz0402_en.fm (10/10) E M C C o m p o n e n t s MMZ0402 Type PACKAGING STYLE REEL DIMENSIONS ø60min. 2.0±0.5 1.0 8.4 +2.0 –0.0 ø13±0.2 ø21±0.8 14.4max. ø180±2.0 Dimensions in mm 4.0±0.1 B A 8.0±0.3 2.0±0.05 3.5±0.05 1.5 +0.1 0 1.75±0.1 TAPE DIMENSIONS P1 K Dimensions in mm Type MMZ0402 160min. Drawing direction A 0.26±0.04 Taping B 0.46±0.04 P1 2.0±0.05 K 0.4max. 200min. 300min. Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150203 / beads_commercial_signal_mmz0402_en.fm