AD EVAL-AD7877EBZ Touch screen controller Datasheet

Data Sheet
Touch Screen Controller
AD7877
FEATURES
FUNCTIONAL BLOCK DIAGRAM
7
AD7877
X+ 12
X– 10
Y+ 13
Y– 11
X– Y– GND X+ Y+ VREF
AUX1/GPIO1
DUAL 3-1
MUX
6
AUX2/GPIO2 5
REF–
AUX3/GPIO3 4
BAT1 3
9 TO 1
INPUT
MUX
BATTERY
MONITOR
IN
SEQUENCER
BAT2 2
CLOCK
STOP
ACQ
LOGIC
20 STOPACQ
RESULTS
REGISTERS
BATTERY
MONITOR
LIMIT
COMPARATOR
LIMIT
REGISTERS
TEMPERATURE
SENSOR
14 AGND
15 DGND
VREF 31
ALERT STATUS/
MASK REGISTER
2.5V
REF
AOUT 30
ARNG 29
BUF
CONTROL
REGISTERS
DAC
REGISTER
8-BIT
DAC
ALERT
LOGIC
GPIO
REGISTERS
CONTROL LOGIC AND SERIAL PORT
Personal digital assistants
Smart hand-held devices
Touch screen monitors
Point-of-sale terminals
Medical devices
Cell phones
Pagers
REF+
12-BIT SUCCESSIVE
APPROXIMATION ADC
WITH TRACK-AND-HOLD
18
19
23
26
27
28
CS
DIN
DAV
DCLK
DOUT
VDRIVE
22 ALERT
21 GPIO4
TO
GPIO1-3
PEN INTERRUPT
AND WAKE-UP
ON TOUCH
17 PENIRQ
03796-001
APPLICATIONS
VCC
ADC DATA
4-wire touch screen interface
LCD noise reduction feature (STOPACQ pin)
Automatic conversion sequencer and timer
User-programmable conversion parameters
On-chip temperature sensor: −40°C to +85°C
On-chip 2.5 V reference
On-chip 8-bit DAC
3 auxiliary analog inputs
1 dedicated and 3 optional GPIOs
2 direct battery measurement channels (0.5 V to 5 V)
3 interrupt outputs
Touch-pressure measurement
Wake up on touch function
Specified throughput rate of 125 kSPS
Single supply, VCC of 2.7 V to 5.25 V
Separate VDRIVE level for serial interface
Shutdown mode: 1 µA maximum
32-lead, LFCSP, 5 mm × 5 mm package
25-ball,WLCSP, 2.5 mm × 2.8 mm package
Qualified for automotive applications
Figure 1.
GENERAL DESCRIPTION
The AD7877 is a 12-bit, successive approximation ADC with a
synchronous serial interface and low on resistance switches for
driving touch screens. The AD7877 operates from a single 2.7 V
to 5.25 V power supply (functional operation to 2.2 V), and
features throughput rates of 125 kSPS. The AD7877 features
direct battery measurement on two inputs, temperature and
touch-pressure measurement.
The AD7877 also has an on-board reference of 2.5 V. When not
in use, it can be shut down to conserve power. An external
reference can also be applied and varied from 1 V to +VCC, with
an analog input range of 0 V to VREF. The device includes a
shutdown mode that reduces its current consumption to less
than 1 µA.
Rev. E
To reduce the effects of noise from LCDs, the acquisition phase
of the on-board ADC is controlled via the STOPACQ pin. Userprogrammable conversion controls include variable acquisition
time and first conversion delay. Up to 16 averages can be taken
per conversion. There is also an on-board DAC for LCD backlight or contrast control. The AD7877 runs in either slave or
master mode using a conversion sequencer and timer. It is ideal
for battery-powered systems such as personal digital assistants
with resistive touch screens and other portable equipment.
The part is available in a 32-lead lead frame chip scale package
(LFCSP), and a 25-ball wafer level chip scale package (WLCSP).
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2004–2014 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD7877* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
DESIGN RESOURCES
View a parametric search of comparable parts.
• AD7877 Material Declaration
• PCN-PDN Information
DOCUMENTATION
• Quality And Reliability
Application Notes
• Symbols and Footprints
• AN-738: Using the AD7877 Touch Screen Controller and
the Intel PXA250 Processor Under Windows CE.NET
DISCUSSIONS
• AN-753: Configuring the AD7877
View all AD7877 EngineerZone Discussions.
• AN-766: Using the Noise Reduction Feature on the
AD7877
Data Sheet
SAMPLE AND BUY
Visit the product page to see pricing options.
• AD7877: Touch Screen Controller Data Sheet
SOFTWARE AND SYSTEMS REQUIREMENTS
TECHNICAL SUPPORT
• AD7877 Input Touch Screen Controller Linux Driver
Submit a technical question or find your regional support
number.
REFERENCE MATERIALS
DOCUMENT FEEDBACK
Technical Articles
Submit feedback for this data sheet.
• MS-2210: Designing Power Supplies for High Speed ADC
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
AD7877
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Control Registers ............................................................................ 20
Applications ....................................................................................... 1
Control Register 1 ...................................................................... 20
Functional Block Diagram .............................................................. 1
Control Register 2 ...................................................................... 21
General Description ......................................................................... 1
Sequencer Registers ................................................................... 22
Revision History ............................................................................... 2
Interrupts ..................................................................................... 24
Specifications..................................................................................... 3
Synchronizing the AD7877 to the Host CPU......................... 25
Timing Specifications .................................................................. 5
8-Bit DAC ........................................................................................ 26
Timing Diagrams.......................................................................... 5
Serial Interface ................................................................................ 28
Absolute Maximum Ratings ............................................................ 6
Writing Data ............................................................................... 28
ESD Caution .................................................................................. 6
Write Timing ............................................................................... 29
Pin Configurations and Function Descriptions ........................... 7
Reading Data ............................................................................... 29
Typical Performance Characteristics ............................................. 9
VDRIVE Pin ..................................................................................... 29
Terminology .................................................................................... 13
General-Purpose I/O Pins ............................................................. 30
Circuit Information ........................................................................ 14
GPIO Configuration .................................................................. 30
Touch Screen Principles ............................................................ 14
Grounding and Layout .................................................................. 32
Measuring Touch Screen Inputs ............................................... 15
PCB Design Guidelines for Chip Scale Packages ................... 32
Touch-Pressure Measurement .................................................. 16
Register Maps .................................................................................. 33
STOPACQ Pin ............................................................................ 16
Detailed Register Descriptions ..................................................... 35
Temperature Measurement ....................................................... 17
GPIO Registers ........................................................................... 42
Battery Measurement ................................................................. 18
Outline Dimensions ....................................................................... 44
Auxiliary Inputs .......................................................................... 19
Ordering Guide .......................................................................... 45
Limit Comparison ...................................................................... 19
Automotive Products ................................................................. 45
REVISION HISTORY
12/14—Rev. D to Rev. E
Added Figure 50; Renumbered Sequentially .............................. 44
Updated Outline Dimensions ....................................................... 44
Changes to Ordering Guide .......................................................... 45
12/11—Rev. C to Rev. D
Change to Features Section ............................................................. 1
Updated Outline Dimensions ....................................................... 44
Changes to Ordering Guide .......................................................... 44
Added Automotive Products Section........................................... 44
9/09—Rev. B to Rev. C
Changes to Offset Error and Gain Error Parameters .................. 3
Added VBAT to GND Parameter ...................................................... 6
Changes to Pin 23 Description ....................................................... 7
Changes to Power Management (Control Register 2,
Bits[7:6]) Section ............................................................................ 22
Changes to Bit 7 Description (Table 17) ...................................... 36
Updated Outline Dimensions ....................................................... 44
Changes Ordering Guide ............................................................... 44
6/06—Rev. A to Rev. B
Added Wafer Level Chip Scale Package .......................... Universal
Changes to Table 3.............................................................................6
Changes to Figure 21...................................................................... 11
Change to Figure 25 ....................................................................... 12
Changes to Figure 38 and Figure 39 ............................................ 23
Change to Figure 40 ....................................................................... 24
Changes to Data Available Output (DAV) Section .................... 24
Updated Outline Dimensions ....................................................... 42
Changes to Ordering Guide .......................................................... 42
11/04—Rev. 0 to Rev. A
Changes to Absolute Maximum Ratings .......................................6
Changes to Figure 4 ...........................................................................7
Changes to Table 4.............................................................................7
Changes to Grounding and Layout section ................................ 32
Changes to Figure 42...................................................................... 32
Changes to Ordering Guide .......................................................... 43
7/04—Revision 0: Initial Version
Rev. E | Page 2 of 45
Data Sheet
AD7877
SPECIFICATIONS
VCC = 2.7 V to 3.6 V, VREF = 2.5 V internal or external, fDCLK = 2 MHz, TA = −40°C to +85°C, unless otherwise noted.
Table 1.
Parameter
DC ACCURACY
Resolution
No Missing Codes
Integral Nonlinearity (INL) 1
Differential Nonlinearity (DNL)1
Negative DNL
Positive DNL
Offset Error1
Gain Error1
Noise
Power Supply Rejection
Internal Clock Frequency
SWITCH DRIVERS
On Resistance1
Y+, X+
Y−, X−
ANALOG INPUTS
Input Voltage Ranges
DC Leakage Current
Input Capacitance
Accuracy
REFERENCE INPUT/OUTPUT
Internal Reference Voltage
Internal Reference Tempco
VREF Input Voltage Range
DC Leakage Current
VREF Input Impedance
TEMPERATURE MEASUREMENT
Temperature Range
Resolution
Differential Method 2
Single Conversion Method 3
Accuracy
Differential Method2
Single Conversion Method3
BATTERY MONITOR
Input Voltage Range
Input Impedance
Accuracy
Min
Typ
12
11
12
Max
Unit
±2
Bits
Bits
LSB
−0.99
+2
±5
±3
70
70
2
LSB
LSB
LSB
LSB
µV rms
dB
MHz
14
14
Ω
Ω
0
VREF
±0.1
30
0.3
2.44
2.55
±50
1
VCC
±1
1
−40
+85
V
µA
pF
%
V
ppm/°C
V
µA
GΩ
Test Conditions/Comments
LSB size = 610 µV
Minimum LSB size = 610 µV
Specified for 11bits
Specified for 11 bits; external reference
All channels, internal VREF
CS = GND or VCC; typically 25 Ω when the on-board
reference is enabled
°C
1.6
0.3
°C
°C
±4
±2
°C
°C
0°C to 70°C
Calibrated at 25°C
V
kΩ
%
@ VREF = 2.5 V
Sampling, 1 GΩ when the battery monitor is off
External/internal reference, see Figure 26
0.5
5
14
1
3.2
Rev. E | Page 3 of 45
AD7877
Parameter
DAC
Resolution
Integral Nonlinearity
Differential Nonlinearity
Voltage Mode
Output Voltage Range
Slew Rate
Output Settling Time
Capacitive Load Stability
Output Impedance
Short-Circuit Current
Current Mode
Output Current Range
Output Impedance
LOGIC INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
Input Capacitance, CIN 4
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Floating-State Leakage Current
Floating-State Output Capacitance4
Output Coding
CONVERSION RATE
Conversion Time
Throughput Rate
POWER REQUIREMENTS
VCC (Specified Performance)
VDRIVE
ICC
Converting Mode
Static
Shutdown Mode
Data Sheet
Min
Typ
Max
Unit
Test Conditions/Comments
8
±1
±1
Bits
Bits
0 − VCC/2
0 − VCC
−0.4, +0.5
12
50
75
21
V
V
V/µs
µs
pF
kΩ
mA
DAC register Bit 2 = 0, Bit 0 = 0
DAC register Bit 2 = 0, Bit 0 = 1
µA
DAC register, Bit 2 = 1; full-scale current is set by RRNG
Power-down mode
0
Guaranteed monotonic by design
15
100
1000
Open
0.7 VDRIVE
0.3
VDRIVE
±1
10
VDRIVE − 0.2
0.4
±10
10
0 to 3/4 scale, RLOAD = 10 kΩ, CLOAD = 50 pF
RLOAD = 10 kΩ
Power-down mode
V
V
µA
pF
Typically 10 nA, VIN = 0 V or VCC
V
V
µA
pF
ISOURCE = 250 µA, VCC/VDRIVE = 2.7 V to 5.25 V
ISINK = 250 µA
Straight (natural) binary
8
125
2.7
1.65
240
650
900
150
µs
kSPS
CS high to DAV low
3.6
VCC
V
V
Functional from 2.2 V to 5.25 V
380
900
µA
µA
µA
µA
1
µA
See the Terminology section.
Difference between Temp0 and Temp1 measurement. No calibration necessary.
3
Temperature drift is −2.1 mV/°C.
4
Sample tested @ 25°C to ensure compliance.
1
2
Rev. E | Page 4 of 45
Digital inputs = 0 V or VCC
ADC on, internal reference off, VCC = 3.6 V
ADC on, internal reference on, VCC = 3.6 V
ADC on, internal reference on, DAC on
ADC on, but not converting, internal reference off,
VCC = 3.6 V
Data Sheet
AD7877
TIMING SPECIFICATIONS
TA = TMIN to TMAX, unless otherwise noted, VCC = 2.7 V to 5.25 V, VREF = 2.5 V. Sample tested at 25°C to ensure compliance. All input
signals are specified with tR = tF = 5 ns (10% to 90% of VCC) and timed from a voltage level of 1.6 V.
Table 2.
Parameter
fDCLK 1
t1
t2
t3
t4
t5
t6 2
t7 2
t8 3
t9
Limit at TMIN, TMAX
10
20
16
20
20
12
12
16
16
16
0
Unit
kHz min
MHz max
ns min
ns min
ns min
ns min
ns min
ns max
ns max
ns max
ns min
Description
CS falling edge to first DCLK rising edge
DCLK high pulse width
DCLK low pulse width
DIN setup time
DIN hold time
CS falling edge to DOUT, three-state disabled
DCLK falling edge to DOUT valid
CS rising edge to DOUT high impedance
CS rising edge to DCLK ignored
Mark/space ratio for the DCLK input is 40/60 to 60/40.
Measured with the load circuit of Figure 3 and defined as the time required for the output to cross 0.4 V or 2.0 V.
3
t8 is derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit shown in Figure 3. The measured number is then
extrapolated back to remove the effects of charging or discharging the 50 pF capacitor. This means that the time, t8, quoted in the timing characteristics is the true bus
relinquish time of the part and is independent of the bus loading.
1
2
TIMING DIAGRAMS
CS
t1
t2
1
DCLK
2
t9
t3
3
15
16
t5
t4
MSB
LSB
t7
DOUT
t8
MSB
LSB
Figure 2. Detailed Timing Diagram
200µA
TO OUTPUT
PIN
IOL
1.6V
CL
50pF
200µA
IOH
Figure 3. Load Circuit for Digital Output Timing Specifications
Rev. E | Page 5 of 45
03796-004
t6
03796-003
DIN
AD7877
Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 3.
Parameter
VCC to GND
Analog Input Voltage to GND
Digital Input Voltage to GND
Digital Output Voltage to GND
VREF to GND
VBAT to GND
Input Current to Any Pin Except Supplies 1
ESD Rating (IEC 1000-4-2, Air Discharge)
Tablet Pins (X+, X−, Y+, Y−)
Other Pins
Operating Temperature Range
Storage Temperature Range
Junction Temperature
LFCSP Package
Power Dissipation
θJA Thermal Impedance
IR Reflow Peak Temperature
Pb-Free Parts Only
Lead Temperature (Soldering 10 sec)
1
Rating
−0.3 V to +7 V
−0.3 V to VCC + 0.3 V
−0.3 V to VCC + 0.3 V
−0.3 V to VCC + 0.3 V
−0.3 V to VCC + 0.3 V
−0.3 V to VCC +5 V
10 mA
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
ESD CAUTION
4 kV
2 kV
−40°C to +85°C
−65°C to +150°C
150°C
450 mW
135.7°C/W
220°C
260°C (±0.5°C)
300°C
Transient currents of up to 100 mA do not cause SCR latch-up.
Rev. E | Page 6 of 45
Data Sheet
AD7877
NC
VREF
AOUT
ARNG
VDRIVE
DOUT
DCLK
NC
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
32
31
30
29
28
27
26
25
PIN 1
NC
NC 1
24
BAT2 2
23
DAV
BAT1 3
22
ALERT
21
GPIO4
20
STOPACQ
AUX1/GPIO1 6
19
DIN
VCC 7
18
CS
NC 8
17
PENIRQ
AD7877
TOP VIEW
(Not to Scale)
DOUT
VDRIVE
ARNG
AOUT
ALERT
GPIO4
DAV
VREF
BAT2
STOP
ACQ
DIN
AUX2/
GPI02
BAT1
AUX3/
GPI03
CS
PENIRQ
AGND
VCC
AUX1/
GPI01
DGND
Y+
X+
Y–
X–
16
NOTES
1. NC = NO CONNECT
2. THE EXPOSED PAD IS NOT CONNECTED INTERNALLY. FOR
INCREASED RELIABILITY OF THE SOLDER JOINTS AND
MAXIMUM THERMAL CAPABILITY, IT IS RECOMMENDED
THAT THE PAD BE SOLDERED TO GROUND PLANE.
03796-051
15
NC
14
DGND
13
AGND
12
Y+
11
X+
10
X–
NC
9
Y–
AUX2/GPIO2 5
AD7877 WLCSP
TOP VIEW
Not to Scale
03796-002
AUX3/GPIO3 4
DCLK
Figure 5. WLCSP Pin Configuration
Figure 4. LFCSP Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
1, 8, 9, 16,
24, 25, 32
2
3
4
5
6
7
10
11
12
13
14
Mnemonic
NC
Description
No Connect.
BAT2
BAT1
AUX3/GPIO3
AUX2/GPIO2
AUX1/GPIO1
VCC
X−
Y−
X+
Y+
AGND
15
DGND
17
18
PENIRQ
CS
19
DIN
20
STOPACQ
21
22
GPIO4
ALERT
23
DAV
26
27
DCLK
DOUT
Battery Monitor Input. ADC Input Channel 7.
Battery Monitor Input. ADC Input Channel 6.
Auxiliary Analog Input. ADC Input Channel 5. Can be reconfigured as GPIO pin.
Auxiliary Analog Input. ADC Input Channel 4. Can be reconfigured as GPIO pin.
Auxiliary Analog Input. ADC Input Channel 3. Can be reconfigured as GPIO pin.
Power Supply Input. The VCC range for the AD7877 is from 2.2 V to 5.25 V.
Touch Screen Position Input.
Touch Screen Position Input. ADC Input Channel 2.
Touch Screen Position Input. ADC Input Channel 0.
Touch Screen Position Input. ADC Input Channel 1.
Analog Ground. Ground reference point for all analog circuitry on the AD7877. All analog input signals and any
external reference signal should be referred to this voltage.
Digital Ground. Ground reference for all digital circuitry on the AD7877. Refer all digital input signals to this
voltage.
Pen Interrupt. Digital active low output (has a 50 kΩ internal pull-up resistor).
Chip Select Input. Active low logic input. This input provides the dual function of initiating conversions on the
AD7877 and enabling the serial input/output register.
SPI® Serial Data Input. Data to be written to the AD7877 registers are provided on this input and clocked into
the register on the rising edge of DCLK.
Stop Acquisition Pin. A signal applied to this pin can be monitored by the AD7877, so that acquisition of new
data by the ADC is halted while the signal is active. Used to reduce the effect of noise from an LCD screen on
the touch screen measurements.
Dedicated General-Purpose Logic Input/Output Pin.
Digital Active Low Output. Interrupt output that goes low if a GPIO data bit is set, or if the AUX1, TEMP1, BAT1,
or BAT2 measurements are out of range.
Data Available Output. Active low logic output. Asserts low when new data is available in the AD7877 results
registers.
External Clock Input. Logic input. DCLK provides the serial clock for accessing data from the part.
Serial Data Output. Logic output. The conversion result from the AD7877 is provided on this output as a serial
data stream. The bits are clocked out on the falling edge of the DCLK input. This output is high impedance
when CS is high.
Rev. E | Page 7 of 45
AD7877
Data Sheet
Pin No.
28
Mnemonic
VDRIVE
29
30
31
ARNG
AOUT
VREF
Description
Logic Power Supply Input. The voltage supplied at this pin determines the operating voltage for the serial
interface of the AD7877.
When the DAC is in current output mode, a resistor from ARNG to GND sets the output range.
Analog Output Voltage or Current from DAC.
Reference Output for the AD7877. The internal 2.5 V reference is available on this pin for use external to the
device. The reference output must be buffered before it is applied elsewhere in a system. To reduce system
noise effects, it is strongly recommended to place a capacitor of 100 nF between the VREF pin and GND.
Alternatively, an external reference can be applied to this input. The voltage range for the external reference is
1.0 V to VCC. For the specified performance, it is 2.5 V on the AD7877.
Rev. E | Page 8 of 45
Data Sheet
AD7877
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, VCC = 2.7 V, VREF = 2.5 V, fSAMPLE = 125 kHz, fDCLK = 16 × fSAMPLE = 2 MHz, unless otherwise noted.
800
200
ADC, REF, AND DAC
180
160
CURRENT (nA)
CURRENT (A)
700
ADC AND REF
600
140
120
–30
–10
0
30
TEMPERATURE (C)
50
70
80
–50
90
Figure 6. Supply Current vs. Temperature
03796-032
500
–50
03796-030
100
–30
–10
10
30
TEMPERATURE (C)
50
70
90
Figure 9. Full Power-Down IDD vs. Temperature
1000
0.6
0.5
0.4
900
DELTA FROM 25C (LSB)
ADC, REF, AND DAC
700
ADC AND REF
600
0.2
0.1
0
–0.1
–0.2
–0.3
–0.4
03796-031
500
400
2.0
0.3
2.3
2.6
2.9
3.2
3.5 3.8
VCC (V)
4.1
4.4
4.7
–0.5
–0.6
–50
5.0
Figure 7. Supply Current vs. VCC
–10
10
30
TEMPERATURE (C)
50
70
90
1.0
0.5
0.8
0.4
0.6
0.3
0.4
0.2
INL (LSB)
0.1
0
–0.1
–0.2
0.2
0
–0.2
–0.4
–0.3
–0.5
–30
–10
10
30
TEMPERATURE (C)
50
70
03796-044
–0.6
–0.4
03796-039
DELTA FROM 25C (LSB)
–30
Figure 10. Change in ADC Offset vs. Temperature
0.6
–0.6
–50
03796-040
CURRENT (A)
800
–0.8
–1.0
90
Figure 8. Change in ADC Gain vs. Temperature
0
500
1000
1500
2000 2500
CODE
Figure 11. ACD INL Plot
Rev. E | Page 9 of 45
3000
3500
4000
AD7877
Data Sheet
1.0
16
0.8
14
REFERENCE CURRENT (A)
0.6
0.2
0
–0.2
–0.4
–0.6
0
500
1000
1500
2000 2500
CODE
3000
3500
6
4
0
–50
4000
Figure 12. ADC DNL Plot
–30
–10
10
30
TEMPERATURE (C)
50
70
90
Figure 15. External Reference Current vs. Temperature
22
2.520
20
2.515
2.510
18
X– TO GND
2.505
16
VREF (V)
RON (Ω)
8
03796-046
–1.0
10
2
03796-045
–0.8
12
Y– TO GND
14
Y+ TO VCC
2.495
2.490
12
2.485
03796-048
10
X+ TO VCC
8
2.7
2.500
3.1
3.5
3.9
4.3
4.7
5.1
2.480
5.5
2.475
–50
VCC (V)
Figure 13. Switch On Resistance vs. VCC
(X+, Y+: VCC to Pin; X−, Y−: Pin to GND)
03796-033
DNL (LSB)
0.4
–30
–10
10
30
TEMPERATURE (C)
50
70
90
Figure 16. Internal VREF vs. Temperature
22
2.508
20
X– TO GND
2.506
18
VREF (V)
Y– TO GND
14
Y+ TO VCC
X+ TO VCC
–20
0
20
40
60
2.498
2.496
2.6
80
TEMPERATURE (°C)
Figure 14. Switch On Resistance vs. Temperature
(X+, Y+: VCC to Pin; X−, Y−: Pin to GND)
03796-034
10
8
–40
2.502
2.500
12
03796-049
RON (Ω)
2.504
16
2.9
3.2
3.5
3.8
4.1
VCC (V)
4.4
Figure 17. Internal VREF vs. VCC
Rev. E | Page 10 of 45
4.7
5.0
Data Sheet
AD7877
3145
6
3135
3115
INTERNAL VREF (V)
ADC CODE (Decimal)
3125
3105
3095
3085
3075
NO CAP
0.711µs SETTLING TIME
2.5
3065
3045
–50
–10
–30
10
30
TEMPERATURE (°C)
50
70
03796-047
03796-041
100nF CAP
54.64µs SETTLING TIME
3055
0
–20
90
0
20
40
60
80
100
120
TURN-ON TIME (µs)
Figure 18. ADC Code vs. Temperature (2.7 V Supply)
Figure 21. Internal VREF vs. Turn-On Time
1183
10
1182
INPUT TONE AMPLITUDE (dB)
–10
1180
1179
1178
1176
2.7
03796-042
1177
2.8
2.9
3.0
3.1
3.2
VCC (V)
3.3
3.4
3.5
SNR 70.25dB
THD 78.11dB
–30
–50
–70
–90
–110
–130
03796-035
TEMP1 CODE
1181
–150
3.6
0
Figure 19. Temp1 vs. VCC
10k
20k
FREQUENCY
30k
40k
Figure 22. Typical FFT Plot for the Auxiliary Channels of the AD7877
at 90 kHz Sample Rate and 10 kHz Input Frequency
982
3.50
3.25
981
DAC O/P SOURCE ABILITY
3.00
2.75
980
DAC O/P LEVEL (V)
979
978
977
2.00
1.75
1.50
1.25
1.00
2.8
2.9
3.0
3.1
3.2
VCC (V)
3.3
3.4
3.5
0.50
03796-036
975
2.7
2.25
0.75
976
03796-043
TEMP0 CODE
2.50
DAC O/P SINK ABILITY
0.25
0
3.6
0
Figure 20. Temp0 vs. VCC
1
2
3
4
5
6
7
SOURCE/SINK CURRENT (mA)
8
9
Figure 23. DAC Source and Sink Current Capability
Rev. E | Page 11 of 45
10
AD7877
Data Sheet
: 144mV
03796-037
VDD = 3V
TEMPERATURE = 25C
1
CH1 200mV CH2 100mV
M2.00s
CH1
03796-050
@: 1.296V
–2
780mV
Figure 24. DAC Output Settling Time (Zero Scale to Half Scale)
400
DAC SINK CURRENT
300
200
0
0
25
50
75
100
125
150
175
200
225
03796-038
DAC SINK CURRENT (µA)
500
NOTE: MAXIMUM DAC SINK CURRENT IS
SET ACCORDING TO THE EQUATION:
IMAX = VCC /(RRNG × 6)
0
ERROR (%)
1
Figure 26. Typical Accuracy for Battery Channel (25°C)
600
100
–1
250
INPUT CODE (Decimal)
Figure 25. DAC Sink Current vs. Input Code with RRNG = 1 kΩ
Rev. E | Page 12 of 45
2
Data Sheet
AD7877
TERMINOLOGY
Integral Nonlinearity (INL)
The maximum deviation from a straight line passing through
the endpoints of the ADC transfer function. The endpoints of
the transfer function are zero scale at 1 LSB below the first code
transition, and full scale at 1 LSB above the last code transition.
Differential Nonlinearity (DNL)
The difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Offset Error
The deviation of the first code transition (00…000) to
(00…001) from the ideal (AGND + 1 LSB).
Gain Error
The deviation of the last code transition (111…110) to
(111…111) from the ideal (VREF − 1 LSB) after the offset
error has been adjusted out.
On Resistance
A measure of the ohmic resistance between the drain and the
source of the switch drivers.
Rev. E | Page 13 of 45
AD7877
Data Sheet
CIRCUIT INFORMATION
The core of the AD7877 is a high speed, low power, 12-bit
analog-to-digital converter (ADC) with input multiplexer,
on-chip track-and-hold, and on-chip clock. The results of
conversions are stored in 11 results registers, and the results
from one auxiliary input and two battery inputs can be compared with high and low limits stored in limit registers to generate
an out-of-limit ALERT. The AD7877 also contains low resistance
analog switches to switch the X and Y excitation voltages to the
touch screen, a STOPACQ pin to control the ADC acquisition
period, 2.5 V reference, on-chip temperature sensor, and 8-bit
DAC to control LCD contrast. The high speed SPI serial bus
provides control of, and communication with, the device.
Operating from a single supply from 2.2 V to 5 V, the AD7877
offers throughput rates of up to 125 kHz. The device is available
in a 5 mm × 5 mm, 32-lead, lead frame chip scale package
(LFCSP), and in a 2.5 mm × 2.8 mm, wafer level chip scale
package (WLCSP), with a 5 × 5 ball grid array.
The data acquisition system of the AD7877 has a number of
advanced features:
•
Input channel sequenced automatically or selected by
the host.
•
STOPACQ feature to reduce noise from LCD.
•
Averaging of from 1 to 16 conversions for noise reduction.
•
Programmable acquisition time.
•
Power management.
•
Programmable ADC power-up delay before first
conversion.
•
Choice of internal or external reference.
•
Conversion at preprogrammed intervals.
CONDUCTIVE ELECTRODE
ON BOTTOM SIDE
PLASTIC FILM WITH
TRANSPARENT, RESISTIVE
COATING ON BOTTOM SIDE
Y+
X–
Y–
X+
CONDUCTIVE ELECTRODE
ON TOP SIDE
PLASTIC FILM WITH
TRANSPARENT, RESISTIVE
COATING ON TOP SIDE
LCD SCREEN
Figure 27. Basic Construction of a Touch Screen
The Y layer has conductive electrodes running along the top
and bottom edges, allowing the application of an excitation
voltage down the Y layer from top to bottom.
Provided that the layers are of uniform resistivity, the voltage at
any point between the two electrodes is proportional to the
horizontal position for the X layer and the vertical position for
the Y layer.
When the screen is touched, the two layers make contact. If
only the X layer is excited, the voltage at the point of contact,
and therefore the horizontal position, can be sensed at one of
the Y layer electrodes. Similarly, if only the Y layer is excited,
the voltage, and therefore the vertical position, can be sensed at
one of the X layer electrodes. By switching alternately between
X and Y excitation and measuring the voltages, the X and
Y coordinates of the contact point can be found.
In addition to measuring the X and Y coordinates, it is also
possible to estimate the touch pressure by measuring the
contact resistance between the X and Y layers. The AD7877 is
designed to facilitate this measurement.
TOUCH SCREEN PRINCIPLES
A 4-wire touch screen consists of two flexible, transparent,
resistive-coated layers that are normally separated by a small air
gap. The X layer has conductive electrodes running down the
left and right edges, allowing the application of an excitation
voltage across the X layer from left to right.
03796-005
The AD7877 is a complete, 12-bit data acquisition system for
digitizing positional inputs from a touch screen in PDAs and
other devices. In addition, it can monitor two battery voltages,
ambient temperature, and three auxiliary analog voltages, with
high and low limit comparisons on three of the inputs, and has
up to four general-purpose logic I/O pins.
Figure 28 shows an equivalent circuit of the analog input
structure of the AD7877, showing the touch screen switches,
the main analog multiplexer, the ADC with analog and
differential reference inputs, and the dual 3-to-1 multiplexer
that selects the reference source for the ADC.
Rev. E | Page 14 of 45
Data Sheet
AD7877
VCC
The voltage seen at the input to the ADC in Figure 29 is
VIN = VCC ×
X+
X–
REF
INT/EXT
Y+
Y–
X– Y– GND X+ Y+ VREF
DUAL 3-1
MUX
9 TO 1
I/P
MUX
AUX1/GPIO2
AUX2/GPIO3
AUX3/GPIO4
REF–
IN+
BAT1
REF+
12-BIT SUCCESSIVE
APPROXIMATION ADC
WITH TRACK-AND-HOLD
TEMPERATURE
SENSOR
The disadvantages of the single-ended method are as follows:
•
It can be used only if VCC is close to VREF. If VCC is greater
than VREF, some positions on the screen are outside the
range of the ADC. If VCC is less than VREF, the full range of
the ADC is not used.
•
The ratio of VCC to VREF must be known. If VREF and/or VCC
vary relative to one another, this can introduce errors.
•
Voltage drops across the switches can introduce errors.
Touch screens can have a total end-to-end resistance
ranging from 200 Ω to 900 Ω. Taking the lowest screen
resistance of 200 Ω and a typical switch resistance of 14 Ω
can reduce the apparent excitation voltage to 200/228 ×
100 = 87% of its actual value. In addition, the voltage drop
across the low-side switch adds to the ADC input voltage.
This introduces an offset into the input voltage, thus, it can
never reach zero.
Figure 28. Analog Input Structure
The AD7877 can be set up to automatically convert either
specific input channels or a sequence of channels. The results of
the ADC conversions are stored in the results registers. See the
Serial Interface section for details.
When measuring the ancillary analog inputs (AUX1 to AUX3,
BAT1 and BAT2), the ADC uses the internal reference, or an
external reference applied to the VREF pin, and the measurement
is referred to GND.
MEASURING TOUCH SCREEN INPUTS
When measuring the touch screen inputs, it is possible to
measure using the internal (or external) reference, or to use the
touch screen excitation voltage as the reference and perform a
ratiometric, differential measurement. The differential method
is the default and is selected by clearing the SER/DFR bit
(Bit 11) in Control Register 1. The single-ended method is
selected by setting this bit.
Single-Ended Method
Figure 29 illustrates the single-ended method for the Y position.
For the X position, the excitation voltage is applied to X+ and
X− and the voltage measured at Y+.
The single-ended method is adequate for applications that use a
fairly blunt and imprecise instrument for an input device, such
as a finger.
Ratiometric Method
The ratiometric method illustrated in Figure 30 shows the
negative input of the ADC reference tied to Y− and the positive
input connected to Y+. Thus, the screen excitation voltage
provides the reference for the ADC. The input of the ADC is
connected to X+ to determine the Y position.
VCC
VCC
Y+
(1)
The advantage of the single-ended method is that the touch
screen excitation voltage can be switched off once the signal is
acquired. Because a screen can draw over 1 mA, this is a
significant consideration for a battery-powered system.
03796-006
BAT2
RY −
RYTOTAL
Y+
VREF
X+
X+
INPUT
(VIA MUX)
INPUT
(VIA MUX)
REF+
ADC
REF+
TOUCH
SCREEN
ADC
REF–
Y–
GND
GND
03796-008
REF–
Y–
03796-007
TOUCH
SCREEN
Figure 30. Ratiometric Conversion of Touch Screen Inputs
Figure 29. Single-Ended Conversion of Touch Screen Inputs
Rev. E | Page 15 of 45
AD7877
Data Sheet
For greater accuracy, the ratiometric method has two significant
advantages:
TOUCH
RESISTANCE
The reference to the ADC is provided from the actual
voltage across the screen; therefore, when the voltage drops
across the switches, it has no effect.
Because the measurement is ratiometric, it does not matter
if the voltage across the screen varies in the long term.
However, it must not change after the signal has been
acquired.
X–
Y–
Y+
X+
MEASURE
Z1 POSITION
TOUCH
RESISTANCE
The disadvantage of the ratiometric method is that the screen
must be powered up at all times because it provides the
reference voltage for the ADC.
Y–
X–
Y+
X+
TOUCH
RESISTANCE
TOUCH-PRESSURE MEASUREMENT
The pressure applied to the touch screen via a pen or finger can
also be measured with the AD7877 using some simple calculations. The contact resistance between the X and Y plates is
measured providing a good indication of the size of the
depressed area and, therefore, the applied pressure. The area of
the spot that is touched is proportional to the size of the object
touching it. The size of this resistance (RTOUCH) can be calculated
using two different methods.
First Method
The first method requires the user to know the total resistance
of the X-plate tablet (RX). Three touch screen conversions are
required:

Measurement of the X position, XPOSITION (Y+ input).

Measurement of the Y− input with the excitation voltage
applied to Y+ and X− (Z1 measurement).

Measurement of the X+ input with the excitation voltage
applied to Y+ and X− (Z2 measurement).
These three measurements are illustrated in Figure 31.
The AD7877 has two special ADC channel settings that
configure the X and Y switches for Z1 and Z2 measurement and
store the results in the Z1 and Z2 results registers. The Z1
measurement is ADC Channel 1010b, and the result is stored in
the register with Read Address 11010b. The Z2 measurement is
ADC Channel 0010b, and the result is stored in the register with
Read Address 10010b.
Y–
X–
MEASURE
Z2 POSITION
Figure 31. Three Measurements Required for Touch Pressure
Second Method
The second method requires the user to know the resistance of
the X-plate and Y-plate tablets. Three touch screen conversions
are required, a measurement of the X position (XPOSITION),
Y position (YPOSITION), and Z1 position.
The following equation also calculates the touch resistance:
RTOUCH = RXPlate × (XPOSITION /4096) × [(4096/Z1) − 1]
− RYPlate × [1 − (YPOSITION/4096)]
(3)
STOPACQ PIN
As previously explained in the Touch Screen Principles section,
touch screens are composed of two resistive layers, normally
placed over an LCD screen. Because these layers are in close
proximity to the LCD screen, noise can be coupled from the
screen onto these resistive layers, causing errors in the touch
screen positional measurements.
For example, a jitter might be noticeable in the cursor on-screen.
In most LCD touch screen systems, a signal, such as an LCD
invert signal or other control signal, is present, and noise is
usually coupled onto the touch screen during the active period
of this signal (see Figure 32).
The touch resistance can then be calculated using the following
equation:
RTOUCH = (RXPlate) × (XPOSITION /4096 × [Z2/Z1) − 1]
MEASURE
X POSITION
LCD SIGNAL
(2)
TOUCH SCREEN
SIGNAL
NOISY
PERIOD
NOISY
PERIOD
Figure 32. Effect of LCD Noise on Touch Screen Measurements
Rev. E | Page 16 of 45
03796-010

Y+
03796-009

X+
Data Sheet
AD7877
The LCD control signal should be applied to the STOPACQ pin.
To ensure that acquisition never occurs during the noisy period
when the LCD signal is active, the AD7877 monitors this signal.
No acquisitions take place when the control signal is active. Any
acquisition that is in progress when the signal becomes active is
aborted and restarts when the signal becomes inactive again.
To accommodate signals of different polarities on the
STOPACQ pin, a user-programmable register bit is used to
indicate whether the signal is active high or low. The POL bit
is Bit 3 in Control Register 2, Address 0x02. Setting POL to 1
indicates that the signal on STOPACQ is active high; setting
POL to 0 indicates that it is active low. POL defaults to 0 on
power-up. To disable monitoring of STOPACQ, the pin should
be tied low if POL = 1, or tied high if POL = 0. Under no
circumstances should the pin be left floating.
The signal on STOPACQ has no effect while the ADC is in
conversion mode, or during the first conversion delay time.
(See the Control Registers section for details on the first
conversion delay.)
When enabled, the STOPACQ monitoring function is implemented on all input channels to the ADC: AUX1, AUX2, BAT1,
BAT2, TEMP1, and TEMP2, as well as on the touch screen
input channels.
TEMPERATURE MEASUREMENT
Two temperature measurement options are available on the
AD7877: the single conversion method and the differential
conversion method. The single conversion method requires
only a single measurement on ADC Channel 1000b. Whereas
differential conversion requires two measurements, one on
ADC Channel 1000b and a second on ADC Channel 1001b.
The results are stored in the results registers with Address 11000b
(TEMP1) and Address 11001b (TEMP2). The AD7877 does not
provide an explicit output of the temperature reading; the
system must perform some external calculations. Both methods
are based on an on-chip diode measurement.
measured. This method provides a resolution of approximately
0.3°C and a predicted accuracy of ±2.5°C.
The temperature limit comparison is performed on the result in
the TEMP1 results register, which is simply the measurement of
the diode forward voltage. The values programmed into the high
and low limits should be referenced to the calibrated diode forward voltage to make accurate limit comparisons. An example
is shown in the Limit Comparison section.
Differential Conversion Method
The differential conversion method is a 2-point measurement.
The first measurement is performed with a fixed bias current
into a diode (when the TEMP1 channel is selected), and the
second measurement is performed with a fixed multiple of the
bias current into the same diode (when the TEMP2 channel is
selected). The voltage difference in the diode readings is proportional to absolute temperature and is given by the following
formula:
∆VBE = (kT/q) × (ln N)
(4)
where:
VBE represents the diode voltage.
N is the bias current multiple (typical value for AD7877 = 120).
k is Boltzmann’s constant.
q is the electron charge.
This method provides a resolution of approximately 1.6°C, and
a guaranteed accuracy of ±4°C without calibration. Determination of the N value on a part-by-part basis improves accuracy.
Assuming a current multiple of 120, which is a typical value
for the AD7877, taking Boltzmann’s constant, k = 1.38054 ×
10−23 electrons V/°K, the electron charge q = 1.602189 × 10−19,
then T, the ambient temperature in Kelvin, would be calculated
as follows:
∆VBE = (kT/q) × (ln N)
T°k = (∆VBE × q)/(k × ln N)
= (∆VBE × 1.602189 × 10−19)/(1.38054 × 10−23 × 4.65)
T°C = 2.49 × 120 × ∆VBE − 273
∆VBE is calculated from the difference in readings from the first
conversion to the second conversion. The user must perform
the calculations to get ∆VBE, and then calculate the temperature
value in degrees. Figure 33 shows a block diagram of the
temperature measurement circuit.
TEMP1
Single Conversion Method
The single conversion method makes use of the fact that the
temperature coefficient of a silicon diode is approximately
−2.1 mV/°C. However, this small change is superimposed on
the diode forward voltage, which can have a wide tolerance. It
is, therefore, necessary to calibrate by measuring the diode
voltage at a known temperature to provide a baseline from
which the change in forward voltage with temperature can be
Rev. E | Page 17 of 45
I
TEMP2
I20 × I
MUX
VBE
ADC
03796-011
It is only during the sample or acquisition phase of the ADC
operation of the AD7877 that noise from the LCD screen has an
effect on the ADC measurements. During the hold or
conversion phase, the noise has no effect, because the voltage at
the input of the ADC has already been acquired. Therefore, to
minimize the effect of noise on the touch screen measurements,
the ADC acquisition phase should be halted.
Figure 33. Block Diagram of Temperature Measurement Circuit
AD7877
Data Sheet
Temperature Calculations
BATTERY MEASUREMENT
If an explicit temperature reading in °C is required, then this is
calculated as follows for the single measurement method:
The AD7877 can monitor battery voltages from 0.5 V to 5 V on
two inputs, BAT1 and BAT2. Figure 34 shows a block diagram
of a battery voltage monitored through the BAT1 pin. The
voltage to the VCC pin of the AD7877 is maintained at the
desired supply voltage via the dc/dc regulator while the input
to the regulator is monitored. This voltage on BAT1 is divided
down by 2 internally, so that a 5 V battery voltage is presented
to the ADC as 2.5 V. To conserve power, the divider circuit is on
only during the sampling of a voltage on BAT1. The BAT2 input
circuitry is identical.
1.
Calculate the scale factor of the ADC in degrees per LSB:
Degrees per LSB = ADC LSB size/−2.1 mV =
(VREF/4096)/−2.1 mV
2.
Save the ADC output, DCAL, at the calibration
temperature, TCAL.
3.
Take ADC reading, DAMB, at the temperature to be
measured, TAMB.
4.
Calculate the difference in degrees between TCAL and TAMB
using
The BAT1 input is ADC Channel 0110b and the result is stored
in Register 10110b. The BAT2 input is ADC Channel 0111b and
the result is stored in Register 10111b.
∆T = (DAMB − DCAL) × degrees per LSB
5.
DC-DC
CONVERTER
BATTERY
0.5V TO 5V
Add ∆T to TCAL
VCC
BAT1
Example:
5kΩ
The internal 2.5 V reference is used.
VREF
SW
0.25V–2.5V
ADC
Degrees per LSB = (2.5/4096)/−2.1 × 10−3 = −0.291
2.
The ADC output is 983 decimal at 25°C, equivalent to a
diode forward voltage of 0.6 V.
3.
The ADC output at TAMB is 880.
4.
∆T = (880 − 983) × −0.291 = 30°
5.
TAMB = 25 + 30 = 55°C
03796-012
5kΩ
1.
Figure 34. Block Diagram of Battery Measurement Circuit
To calculate the temperature explicitly using the differential
method:
1.
Calculate the LSB size of the ADC in V:
LSB = VREF/4096
2.
Subtract TEMP1 from TEMP2 and multiply by LSB size to
get ∆VBE.
3.
Multiply by 2490 and subtract 273 to obtain the
temperature in °C.
Figure 34 shows the ADC using the internal reference of 2.5 V.
The maximum battery voltage that the AD7877 can measure
changes when a different reference voltage is used. The maximum voltage that is measurable is VREF × 2, because this voltage
gives a full-scale output from the ADC. If a smaller reference is
used, such as 2 V, then the maximum measurable battery voltage
is 4 V. If a larger reference is used, such as 3.5 V, then the maximum measurable battery voltage is 7 V. The internal reference is
particularly suited for use when measuring lithium-ion batteries,
wherein the minimum voltage is about 2.7 V and the maximum
voltage is about 4.2 V. A proper choice of external reference
ensures that other voltage ranges can be accommodated.
Example:
The internal 2.5 V reference is used.
1.
LSB size = 2.5 V/4096 = 6.1 × 10−4 V(610 µV)
2.
TEMP1 = 880 and TEMP2 = 1103:
∆VBE = (1103 − 880) × 6.1× 10−4 = 0.136 V
3.
T = 0.136 × 2490 − 273 = 65°C
Rev. E | Page 18 of 45
Data Sheet
AD7877
AUXILIARY INPUTS
The AD7877 has three auxiliary analog inputs, AUX1 to AUX3.
These channels have a full-scale input range from 0 V to VREF.
The ADC channel addresses for AUX1 to AUX3 are 0011b,
0100b, and 0101b, and the results are stored in Register 10011b,
Register 10100b, and Register 10101b. These pins can also be
reconfigured as general-purpose logic inputs/outputs, as
described in the GPIO Configuration section.
Instead, it is necessary to calibrate the temperature measurement, calculate the TEMP1 readings at the high and low limit
temperatures, and then program those values into the limit
registers, as follows:
1.
LSB per degree = −2.1 mV/(VREF/4096).
2.
Save the calibration reading DCAL at the calibration
temperature, TCAL.
3.
Subtract TCAL from limit temperatures THIGH and TLOW
to get the difference in degrees between the limit
temperatures and the calibration temperature.
4.
Multiply this value by LSB per degree to obtain the
value in LSBs.
5.
Add these values to the digital value at the calibration
temperature to get the digital high and low limit values.
LIMIT COMPARISON
The AUX1 measurement, the two battery measurements, and
the TEMP1 measurement can all be compared with high and
low limits, and an out-of-limit result that generates an alarm
output at the ALERT pin. The limits are stored in registers with
addresses from 00100b to 01011b. After a measurement from
any one of the four channels is converted, it is compared with
the corresponding high and low limits. An out-of-limit result
sets one of the status bits in the alert status/enable register. For
details on these and other registers, see the Register Maps and
Detailed Register Descriptions sections. For details on writing
and reading data, see the Serial Interface section.
As described in the Single Conversion Method section, the
temperature comparison is made using the result of the TEMP1
measurement, that is, the diode forward voltage. Because the
temperature coefficient of the diode is known but the actual
forward voltage can have a wide tolerance, it is not possible
to program the high and low limit registers with predetermined values.
Calculate
Example:
The internal 2.5 V reference is used.
1.
THIGH = +65°C and TLOW = −10°C.
2.
LSB per degree = −2.1 × 10−3/(2.5/4096) = −3.44.
3.
DCAL = 983 decimal at 25°C.
4.
DHIGH = (65 − 25) × −3.44 + 983 = 845.
5.
DLOW = (−10 − 25) × −3.44 + 983 = 1103.
Rev. E | Page 19 of 45
AD7877
Data Sheet
CONTROL REGISTERS
Control Register 1 contains the ADC channel address, the
SER/DFR bit (to choose single or differential methods of touch
screen measurement), the register read address, and the ADC
mode bits. Control Register 1 should always be the last register
to be programmed prior to starting conversions. Its power-on
default value is 0x00. To change any parameter after conversion
has begun, the part should first be put into Mode 00, the
changes made, and then Control Register 1 reprogrammed,
ensuring that it is always the last register to be programmed
before conversions begin.
SER/
DFR
0
CHNL CHNL CHNL CHNL
ADD
ADD
ADD
ADD
3
2
1
0
RD
ADD
4
RD
ADD
3
RD
ADD
2
RD
ADD
1
RD
ADD
0
ADC
ADC
MODE MODE
1
0
03796-013
11
Figure 35. Control Register 1
Control Register 2 sets the timer, reference, polarity, first
conversion delay, averaging, and acquisition time. Its power-on
default value is 0x00. See the Detailed Register Descriptions
section for more information on the control registers.
AVG
1
0
AVG
0
ACQ
1
ACQ
0
PM
1
PM
0
FCD
1
FCD
0
POL
REF
TMR
1
TMR
0
Figure 36. Control Register 2
CONTROL REGISTER 1
ADC Mode (Control Register 1, Bits[1:0])
These bits select the operating mode of the ADC. The AD7877
has three operating modes. These are selected by writing to the
mode bits in Control Register 1. If the mode bits are 00, no
conversion is performed.
Table 5. Control Registera 1 Mode Selection
MODE1
0
0
MODE0
0
1
1
1
0
1
Function
Do not convert (default)
Single-channel conversion, AD7877 in
slave mode
Sequence 0, AD7877 in slave mode
Sequence 1, AD7877 in master mode
If the mode bits are 01, a single conversion is performed on the
channel selected by writing to the channel bits of Control
Register 1 (Bit 7 to Bit 10). At the end of the conversion, if the
TMR bits in Control Register 2 are set to 00, the mode bits
revert to 00 and the ADC returns to no convert mode until a
new conversion is initiated by the host. Setting the TMR bits to
a value other than 00 causes the conversion to be repeated, as
described in the Timer (Control Register 2, Bits[1:0]) section.
The flowchart in Figure 38 shows how the AD7877 operates in
Mode 01.
03796-014
11
The AD7877 can also be programmed to convert a sequence of
selected channels automatically. The two modes for this type of
conversion are slave mode and master mode.
For slave mode operation, the channels to be digitized are
selected by setting the corresponding bits in Sequencer
Register 0. Conversion is initiated by writing 10b to the mode
bits of Control Register 1. The ADC then digitizes the selected
channels and stores the results in the corresponding results
registers. At the end of the conversion, if the TMR bits in
Control Register 2 are set to 00, the mode bits revert to 00 and
the ADC returns to no convert mode until a new conversion is
initiated by the host. Setting the TMR bits to a code other than
00 causes the conversion sequence to be repeated. The
flowchart in Figure 39 shows how the AD7877 operates in
Mode 10.
For master mode operation, the channels to be digitized are
written to Sequencer Register 1. Master mode is then selected
by writing 11 to the mode bits in Control Register 1. In this
mode, the wake-up on touch feature is active, so conversion
does not begin immediately. The AD7877 waits until the screen
is touched before beginning the sequence of conversions. The
ADC then digitizes the selected channels, and the results are
written to the results registers. The AD7877 waits for the screen
to be touched again, or for a timer event if the screen remains
touched, before beginning another sequence of conversions.
The flowchart in Figure 40 shows how the AD7877 operates in
Mode 11.
ADC Channel (Control Register 1, Bits[10:7])
The ADC channel is selected by Bits [10:7] of Control Register 1
(CHADD3 to CHADD0). In addition, the SER/DFR bit, Bit 11,
selects between single-ended and differential conversion. A
complete list of channel addresses is given in Table 6.
For Mode 0 (single-channel) conversion, the channel is selected
by writing the appropriate CHADD3 to CHADD0 code to
Control Register 1.
For sequential channel conversion, channels to be converted are
selected by setting bits corresponding to the channel number in
Sequencer Register 1 for slave mode sequencing or Sequencer
Register 2 for master mode sequencing.
For both single-channel and sequential conversion, normal
(single-ended) conversion is selected by clearing the SER/DFR
bit in Control Register 1. Ratiometric (differential) conversion
is selected by setting the SER/DFR bit.
Rev. E | Page 20 of 45
Data Sheet
AD7877
Table 6. Codes for Selecting Input Channel and Normal or Ratiometric Conversion
Channel
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
-
SER/DFR
CHADD(3:0)
0000
0001
0010
0 01 1
0 1 00
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
10 1 1
1100
1101
1110
1111
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Analog Input
X+ (Y position)
Y+ (X position)
Y− (Z2)
AUX1
AUX2
AUX3
BAT1
BAT2
TEMP1
TEMP2
X+ (Z1)
X+ (Y position)
Y+ (X position)
Y− (Z2)
AUX1
AUX2
AUX3
BAT1
BAT2
TEMP1
TEMP2
X+ (Z1)
X Switches
Y Switches
Off
On
On
Off
X+ off, X− on
Y+ on, Y− off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
X+ OFF, X− ON
Y+ on Y− off
Invalid address
Invalid address
Invalid address
Invalid address
Invalid address
Off
On
On
Off
X+ off, X− on
Y+ on, Y− off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
X+ off, X− on
Y+ on, Y− off
Invalid address
Invalid address
Invalid address
Invalid address
Invalid address
+REF
Y+
X+
Y+
VREF
VREF
VREF
VREF
VREF
VREF
VREF
Y+
−REF
Y−
X−
X−
GND
GND
GND
GND
GND
GND
GND
X−
VREF
VREF
VREF
VREF
VREF
VREF
VREF
VREF
VREF
VREF
VREF
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
CONTROL REGISTER 2
Int/Ext Reference (Control Register 2, Bit[2])
Timer (Control Register 2, Bits[1:0])
If the REF bit in Control Register 2 is 0 (default value), the
internal reference is selected. Buffer any connection made to
VREF while the internal reference is selected (for example, to
supply a reference to other circuits). An external power supply
should not be connected to this pin while REF is equal to 0,
because it might overdrive the internal reference. Because the
internal reference is 2.5 V, it operates only with supply voltages
down to 2.7 V. Below this value, use an external reference.
The TMR bits in Control Register 2 enable the ADC to
repeatedly perform a conversion or conversion sequence either
once only or at intervals of 512 μs, 1.024 ms, or 8.19 ms. In slave
mode, the timer starts as soon as the conversion sequence is
finished. In master mode, the timer starts at the end of a conversion
sequence only if the screen remains touched. If the touch is
released at any stage, then the timer stops and, the next time the
screen is touched, a conversion sequence begins immediately.
Table 7. Control Register 2 Timer Selection
TMR1
0
0
1
1
TMR0
0
1
0
1
Function
Convert only once (default)
Every 1024 clocks (512 μs)
Every 2048 clocks (1.024 ms)
Every 16,384 clocks (8.19 ms)
If the REF bit is 1, the VREF pin becomes an input and the
internal reference is powered down. This overrides any setting
of the PM bits with regard to the reference. An external
reference can then be applied to the REF pin.
Rev. E | Page 21 of 45
AD7877
Data Sheet
STOPACQ Polarity (Control Register 2, Bit[3])
Acquisition Time (Control Register 2, Bits[9:8])
This bit should be set according to the polarity of the signal
applied to the STOPACQ pin. If that signal is active high, that
is, no acquisitions should occur during the high period of the
signal, then the POL bit should be set to 1. If the signal is active
low, then the POL bit should be 0. The default value for POL is 0.
The ACQ bits in Control Register 2 allow the selection of
acquisition times for the ADC of 2 μs (default), 4 μs, 8 μs, or
16 μs. The user can program the ADC with an acquisition time
suitable for the type of signal being sampled. For example,
signals with large RC time constants can require longer
acquisition times.
First Conversion Delay (Control Register 2, Bits[5:4])
The first conversion delay (FCD) bits in Control Register 2
program a delay of 500 ns (default), 128 μs, 1.024 ms, or 8.19 ms
before the first conversion, to allow the ADC time to power up.
This delay also occurs before conversion of the X and Y coordinate channels, to allow extra time for screen settling, and after
the last conversion in a sequence, to precharge PENIRQ. If the
signal on the STOPACQ pin is being monitored and goes active
during the FCD, it is ignored until after the FCD period.
Table 8. First Conversion Delay Selection
FCD
0
1
0
1
Function
1 clock delay (500 ns)
256 clock delays (128 μs)
2048 clock delays (1.024 ms)
16,384 clock delays (8.19 ms)
The power management (PM) bits in Control Register 2 allow
the power management features of the ADC to be programmed.
If the PM bits are 00, the ADC is powered down permanently.
This overrides any setting of the mode bits in Control Register 1.
If the PM bits are 01, the ADC and the reference both power
down when the ADC is not converting. If the PM bits are 10,
the ADC and reference are powered up continuously. If the PM
bits are 11, the ADC, but not the reference, powers down when
the ADC is not converting. If the AD7879 is in full power mode
(PM=10), the master sequencer should not be used. PM bits
must be set to 01 or 11 when using the master sequencer.
Table 9. Power Management Selection
PM0
0
1
1
1
0
1
ACQ0
0
1
0
1
Function
4 clock periods (2 μs)
8 clock periods (4 μs)
16 clock periods (8 μs)
32 clock periods (16 μs)
Averaging (Control Register 2, Bits[11:10])
Signals from touch screens can be extremely noisy. The AVG
bits in Control Register 2 allow multiple conversions to be
performed on each input channel and averaged to reduce noise.
A single conversion can be selected (no averaging), which is the
default, or 4, 8, or 16 conversions can be averaged. Only the
final averaged result is written into the results register.
Table 11. Averaging Selection
Power Management (Control Register 2, Bits[7:6])
PM1
0
0
ACQ1
0
0
1
1
Function
Power down continuously (default)
Power down ADC and reference when
ADC is not converting (powers up with
FCD at start of a conversion)
Powered up continuously
Power down ADC when ADC is not
converting (powers up with FCD at start
of conversion)
AVG1
0
0
1
1
AVG0
0
1
0
1
Function
ADC performs 1 average per channel
ADC performs 4 averages per channel
ADC performs 8 averages per channel
ADC performs 16 averages per channel
SEQUENCER REGISTERS
There are two sequencer registers on the AD7877. Sequencer
Register 0 controls the measurements performed during a slave
mode sequence. Sequencer Register 1 controls the measurements performed during a master mode sequence.
To include a measurement in a slave mode or master mode
sequence, the relevant bit must be set in Sequencer Register 0 or
Sequencer Register 1. Setting Bit 11 includes a measurement on
ADC Channel 0 in the sequence, which is the Y positional
measurement. Setting Bit 10 includes a measurement on ADC
Channel 1 (X+ measurement), and so on, through Bit 1 for
Channel 10. Figure 37 illustrates the correspondence between
the bits in the sequencer registers and the various measurements. Bit 0 in both sequencer registers is not used. See also the
Detailed Register Descriptions section.
11
0
Y+
X+
Z2
AUX
1
AUX
2
AUX
3
BAT
1
BAT
2
TEMP TEMP
1
2
Figure 37. Sequencer Register
Rev. E | Page 22 of 45
Z1
NOT
USED
03796-015
FCD1
0
0
1
1
Table 10. Acquisition Time Selection
Data Sheet
AD7877
HOST PROGRAMS
AD7877 IN MODE 10
HOST PROGRAMS
AD7877 IN MODE 01
VALID
SEQUENCE 0?
NO
GO TO MODE 00
IS FCD
REQUIRED?
NO
YES
SELECT NEXT
CHANNEL
YES
START FCD TIMER
IS FCD
REQUIRED?
IS FCD
FINISHED?
YES
NO
START FCD TIMER
YES
YES
NO
IS FCD
FINISHED?
IS STOPACQ
SIGNAL ACTIVE?
NO
YES
NO
IS STOPACQ
SIGNAL ACTIVE?
YES
START ACQUISITION TIMER
NO
START ACQUISITION TIMER
IS STOPACQ
SIGNAL ACTIVE?
YES
YES
IS STOPACQ
SIGNAL ACTIVE?
NO
NO
NO
IS ACQUISITION
TIME FINISHED?
IS ACQUISITION
TIME FINISHED?
YES
YES
CONVERT
SELECTED CHANNEL
CONVERT
SELECTED CHANNEL
IS AVERAGING
FINISHED?
NO
IS AVERAGING
FINISHED?
NO
NO
YES
YES
WRITE RESULT TO
REGISTERS
WRITE RESULT TO
REGISTERS
LIMIT COMPARISON
LIMIT COMPARISON
OUT-OF-LIMIT?
OUT-OF-LIMIT?
NO
YES
UPDATE ALERT
ENABLE/STATUS
REGISTER
YES
UPDATE ALERT
ENABLE/STATUS
REGISTER
ALERT
SOURCE
ENABLED?
NO
ALERT
SOURCE
ENABLED?
NO
YES
NO
ASSERT ALERT
OUTPUT1
YES
ASSERT ALERT
OUTPUT1
LAST CHANNEL
IN SEQUENCE?
NO
YES
GO TO MODE 00
YES
ONCE-ONLY
MODE?
GO TO MODE 00
NO
NO
START TIMER
START TIMER
1SEE
TIMER
FINISHED?
YES
SEQUENCER REGISTERS SECTION.
NO
TIMER
FINISHED?
YES
03796-016
NO
ONCE-ONLY
MODE?
1SEE SEQUENCER REGISTERS SECTION.
03796-017
YES
Figure 39. Slave Mode Sequencer Operation
Figure 38. Single Channel Operation
Rev. E | Page 23 of 45
AD7877
Data Sheet
HOST PROGRAMS
AD7877 IN MODE 11
GO TO MODE 00
INTERRUPTS
Data Available Output (DAV)
VALID
SEQUENCE 1?
NO
The data available output (DAV) indicates that new ADC data
is available in the results registers. While the ADC is idle or is
converting, DAV is high. Once the ADC has finished converting
and new data has been written to the results registers, DAV goes
low. Taking DAV low to read the registers resets DAV to a high
condition. DAV is also reset, if a new conversion is started by
the AD7877 because the timer expired. The host should attempt
to read the results registers only when DAV is low.
YES
IS
SCREEN
TOUCHED?
NO
YES
SELECT NEXT
CHANNEL
IS FCD
REQUIRED?
NO
YES
START FCD TIMER
CS
IS FCD
FINISHED?
NO
YES
DAV
tCONV
IS STOPACQ
SIGNAL ACTIVE?
AD7877
STATUS
NO
START ACQUISITION TIMER
YES
NEW DATA HOST READS
AVAILABLE RESULTS
IDLE
DAV is useful as a host interrupt in master mode. In this mode,
the host can program the AD7877 to automatically perform a
sequence of conversions, and can be interrupted by DAV at the
end of each conversion sequence.
NO
NO
YES
CONVERT
SELECTED CHANNEL
When the on-board timer is programmed to perform automatic
conversions, a limited time is available to the host to read the
results registers before another sequence of conversions begins.
The DAV signal is reset high when the timer expires, and the
host should not access the results registers while DAV is high.
NO
IS AVERAGING
FINISHED?
ADC
CONVERTING
Figure 41. Operation of DAV Output
IS STOPACQ
SIGNAL ACTIVE?
IS ACQUISITION
TIME FINISHED?
IDLE
SETUP
BY HOST
03796-019
YES
YES
WRITE RESULT TO
REGISTERS
LIMIT COMPARISON
OUT-OF-LIMIT?
Figure 42 shows the worst-case timings for reading the results
registers after DAV has gone low. The timer is set at a
minimum, and the conversion sequence includes all 11 possible
ADC channels. t1 is the time taken for acquisition and
conversion on one ADC channel. t2 shows the minimum timer
delay, that is, 1024 clock periods. t3 is the time taken to read all
11 result registers. If the host wants to read all 11 registers, then
it must do so before the timer expires. t4 is the maximum time
allowable between DAV going low and the host beginning to
read the results registers. If t4 is exceeded, then all registers
cannot be read before the start of a new conversion, and
incorrect data could be read by the host.
NO
YES
UPDATE ALERT
ENABLE/STATUS
REGISTER
ALERT
SOURCE
ENABLED?
NO
YES
ASSERT ALERT
OUTPUT1
NO
LAST CHANNEL
IN SEQUENCE?
YES
YES
ONCE-ONLY
MODE?
NO
IS
SCREEN STILL
TOUCHED?
AD7877
STATUS
NO
t1
t2
CHANNEL 11
CONVERSION AND
ACQUISITION
TIMER INTERVAL
CHNL
1
DAV
YES
START TIMER
CS
YES
NO
1SEE
IS
SCREEN STILL
TOUCHED?
t3
NO
SEQUENCER REGISTERS SECTION.
Figure 42. Timing for Reads after DAV Goes Low
03796-018
YES
t4
DOUT
Figure 40. Master Mode Sequencer Operation
Rev. E | Page 24 of 45
03796-020
TIMER
FINISHED?
Data Sheet
AD7877
NOT
SCREEN TOUCHED
t2 = 512 µs with timer set to 1024 (TMR bits = 01b)
tWRITE = tREAD = 16 CLK period × tDCLK = 800 ns
PENIRQ
DETECTS
TOUCH
PENIRQ
t3 = maximum time taken to write read address and read
11 registers = 800 ns (write) + [800 ns (read) × 11] = 9.6 µs.
ADC
STATUS
t4MAX = t2 − t3 = 512 µs − 9.6 µs = 502.4 µs
Pen Interrupt (PENIRQ)
Y+
VCC
VCC
50kΩ
PENIRQ
X+
X–
RELEASE NOT
DETECTED
ADC IDLE
NOT
TOUCHED
PENIRQ
DETECTS
RELEASE
ADC
CONVERTING
ADC IDLE
Figure 44. PENIRQ Operation for ADC Idle and ADC Converting
SYNCHRONIZING THE AD7877 TO THE HOST CPU
The two suggested methods for synchronizing the AD7877
to its host CPU are slave mode, in which the mode bits can
be either 01b or 10b, and master mode, in which the mode
bits are 11b.
In slave mode, PENIRQ can be used as an interrupt to the host.
When PENIRQ goes low to indicate that the screen has been
touched, the host is awakened. The host can then program the
AD7877 to begin converting in either Mode 01b or Mode 10b,
and can read the result registers after the conversions are
completed.
TOUCH
SCREEN
03796-021
PENIRQ
ENABLE
Y–
TOUCHED
PENIRQ
DETECTS
TOUCH
PENIRQ
ADC
STATUS
PENIRQ
DETECTS
RELEASE
ADC IDLE
NOT
SCREEN TOUCHED
The pen interrupt request output (PENIRQ) goes low whenever
the screen is touched. The pen interrupt equivalent output
circuitry is outlined in Figure 43. This is a digital logic output
with an internal pull-up resistor of 50 kΩ, which means it does
not need an external pull-up. The PENIRQ output idles high.
The PENIRQ circuitry is always enabled, except during
conversions.
NOT
TOUCHED
TOUCHED
03796-022
If fDCLK = 20 MHz (maximum), then tDCLK = 50 ns.
Figure 43. PENIRQ Output Equivalent Circuit
When the screen is touched, PENIRQ goes low. This generates
an interrupt request to the host. When the screen touch ends,
and if the ADC is idle, PENIRQ immediately goes high. If the
ADC is converting, PENIRQ goes high once the ADC becomes
idle. The PENIRQ operation for these two conditions is shown
in Figure 44.
In master mode, DAV can also be used as an interrupt to the
host. However, the host should first initialize the AD7877 in
Mode 11b. The host can then go into sleep mode to conserve
power. The wake-up on touch feature of the AD7877 is active in
this mode, therefore, when the screen is touched, the
programmed sequence of conversions begins automatically.
When the DAV signal asserts, the host reads the new data available in the AD7877 results registers and returns to sleep mode.
This method can significantly reduce the load on the host.
Rev. E | Page 25 of 45
AD7877
Data Sheet
8-BIT DAC
The AD7877 features an on-chip 8-bit DAC for LCD contrast
control. The DAC can be configured for voltage output by
clearing Bit 2 of the DAC register (Address 1110b), or for
current output by setting this bit.
In current mode, it is quite easy to calculate the resistor values
to give the required adjustment range in VOUT using the
following steps:
The output voltage range can be set to 0 to VCC/2 by clearing
Bit 0 of the DAC register, or to 0 to VCC by setting this bit. In
current mode, the output range is selectable by an external
resistor, RRNG, connected between the ARNG pin and GND.
This sets the full-scale output current according to the following
equations:
IFS = VCC/(RRNG × 6)
(5)
In current mode, the DAC sinks current, that is, positive
current flows into ground. The maximum output current is
1000 μA. The DAC is updated by writing to Address 1110b of
the DAC register. The 8 MSBs of the data-word are used for
DAC data.
The most effective way to control LCD contrast with the DAC is
to use it to control the feedback loop of the dc-to-dc converter
that supplies the LCD bias voltage, as shown in Figure 45. The
bias voltage for graphic LCDs is typically in the range of 20 V to
25 V, and the dc-to-dc converter usually has a feedback loop
that attenuates the output voltage and compares it with an
internal reference voltage.
DC-DC
CONVERTER
RRNG 1
IOUT
2.
Decide on the current around the feedback loop. For
reasonable accuracy of the output voltage, this current
should be at least 100 times the input bias current of the
dc-to-dc converter’s comparator
3.
Calculate R3 using the following equation:
VFB
R12
R3
VREF
TO LCD
4.
Calculate R2 for the minimum value of VOUT, when the
DAC has no effect
R2 = R3(VOUT(MIN) − VREF)/VREF
5.
Because the voltage across R3 does not change, subtract
VREF from VOUTMAX and VOUTMIN to get the maximum and
minimum voltages across R2
6.
Calculate the change in feedback current between
minimum and maximum output voltages
ΔI = VR2(MAX)/R2 − VR2(MIN)/R2
This is the required full-scale current of the DAC.
7.
Calculate RRNG from Equation 5
Example:
VOUT
1.
VCC = 5 V
VOUT(MIN) is 20 V and VOUT(MAX) is 25 V
VREF is 1.25 V
2.
Allow 100 μA around the feedback loop.
3.
R3 = 1.25 V/100 μA = 12.5 kΩ
Use the nearest preferred value of 12 kΩ and recalculate
the feedback current as
COMP
GND
NOTES:
1R
RNG IS REQUIRED ONLY IF DAC IS IN CURRENT MODE.
2R1 IS REQUIRED ONLY IF DAC IS IN VOLTAGE MODE.
03796-023
ARNG
R2
AOUT
8-BIT
DAC
Find the required maximum and minimum values of VOUT
from the LCD manufacturer’s data
R3 = VFB/IFB = VREF/IFB
therefore,
RRNG = VCC/(IFS × 6)
AD7877
1.
Figure 45. Using the DAC to Adjust LCD Contrast
The circuit operates as follows. If the DAC is in current mode
when the DAC output is zero, it has no effect on the feedback
loop. Regardless of what the DAC does, the feedback loop
maintains the voltage across R4, VFB, equal to VREF, and the
output voltage, VOUT, is
VREF × (R2 + R3)/R3
As the DAC output is increased, it increases the feedback current,
so the voltage across R2 and, therefore, the output voltage also
increase. Note that the voltage across R3 does not change. This
is important for calculation of the adjustment range.
IFB = 1.25 V/12 kΩ = 104 μA
4.
R2 = (20 V − 1.25 V)/104 μA = 180 kΩ
5.
ΔI = 23.75 V/180 kΩ − 18.75 V/180 kΩ = 28 μA
6.
RRNG = 5 V/(6 × 28 μA) = 30 kΩ
In voltage mode, the circuit operation depends on whether the
maximum output voltage of the DAC exceeds the dc to dc
converter VREF.
Rev. E | Page 26 of 45
Data Sheet
AD7877
When the DAC output voltage is zero, it sinks the maximum
current through R1. The feedback current and, therefore, VOUT
are at their maximum. As the DAC output voltage increases, the
sink current and, thus, the feedback current decrease, and VOUT
falls. If the DAC output exceeds VREF, it starts to source current,
and VOUT has to further decrease to compensate. When the
DAC output is at full scale, VOUT is at its minimum.
5.
R1 = VFS/∆.
6.
Calculate R3 from R1 and R using
R3 = (R1 × RP)/(R1 − RP)
Example:
1.
VCC = 5 V and VFS = VCC. VOUT(MIN) is 20 V and VOUT(MAX) is
25 V. VREF is 1.25 V. Allow 100 µA around the feedback loop.
Note that the effect of the DAC on VOUT is opposite in voltage
mode to that in current mode. In current mode, increasing
DAC code increases the sink current, so VOUT increases with
increasing DAC code. In voltage mode, increasing DAC code
increases the DAC output voltage, reducing the sink current.
2.
RP = 1.25 V/100 µA = 12.5 kΩ.
3.
R2 = 12.5 kΩ × (25 Ω − 1.25 Ω)/1.25 Ω = 237 kΩ.
Calculate the resistor values as follows:
4.
∆I = 25 V/240 kΩ − 20 V/240 kΩ = 21 µA.
1.
Decide on the feedback current as before.
5.
R1 = 5 V/21 µA = 238 kΩ.
2.
Calculate the parallel combination of R1 and R3 when the
DAC output is zero
RP = VREF/IFB
3.
Use the nearest preferred value of 250 kΩ.
6.
R3 = (180 kΩ × 12.5 kΩ)/(180 kΩ − 12.5 kΩ) = 13.4 kΩ.
Use nearest preferred value of 13 kΩ.
Calculate R2 as before, but use RP and VOUT(MAX)
The actual adjustment range using these values is 21 V to 26 V.
R2 = RP(VOUT(MAX) − VREF)/VREF
4.
Use the nearest preferred value of 240 kΩ.
Calculate the change in feedback current between
minimum and maximum output voltages as before using
∆I = VR2(MAX)/R2 − VR2(MIN)/R2
This is equal to the change in current through R1 between
zero output and full scale, which is also given by
∆I = current at zero − current at full scale
= V/R1 − (VREF − V)/R1
= V/R1
Rev. E | Page 27 of 45
AD7877
Data Sheet
SERIAL INTERFACE
Register Address 1111b is not a physical register, but enables an
extended writing mode that allows writing to the GPIO
configuration registers. When the register address is 1111b, the
next four bits of the data-word are the address of a GPIO
configuration register and the eight LSBs are the GPIO
configuration data. For details on the configuration of the GPIO
pins, see the General-Purpose I/O Pins section.
The AD7877 is controlled via a 3-wire serial peripheral
interface (SPI). The SPI has a data input pin (DIN) for inputting
data to the device, a data output pin (DOUT) for reading data
back from the device, and a data clock pin (DCLK) for clocking
data into and out of the device. A chip-select pin (CS) enables
or disables the serial interface.
WRITING DATA
Register Address 0001b is a physical register, Control Register 1,
but this is a special register. It contains data for setting up the
ADC channel and operating mode, but Bit 20 to Bit 6 compose
the register address for reading. These define the register that is
read back during the next read operation. Control Register 1
should be the last register in the AD7877 to be programmed
before starting a conversion. The three types of data-words used
for writing are shown in Figure 46.
Data is written to the AD7877 in 16-bit words. The first four
bits of the word are the register address that directs the AD7877
to the register to write to. The next 12 bits are data. How the
AD7877 handles the data bits depends on the register address.
Register Address 0000b is a dummy address, which does
nothing. Register Addresses 0010b to Register Address 1110b
are 12-bit registers that perform various functions as described
in the register map.
16-BIT DATA-WORD
D15
D14
D13
D12
D11
D10
D9
WADD3
WADD2
WADD1
WADD0
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
D6
D5
D4
D3
D2
D1
D0
D4
D3
D2
D1
D0
RADD0
MODE 1
MODE 0
WRITING TO A REGISTER
D8
D7
4-BIT REGISTER WRITE ADDRESS
12 BITS DATA
EXTENDED WRITE OPERATION TO GPIO REGISTERS
1
1
1
1
EADD3
EXTENDED WRITE ADDRESS
EADD2
EADD1
EADD0
D7
D6
D5
4-BIT EXTENDED ADDRESS
8 BITS GPIO DATA
WRITING TO CONTROL REGISTER 1 TO SET ADC CHANNEL, MODE, AND READ REGISTER ADDRESS
0
0
0
0
SER/DFR CHADD3 CHADD2 CHADD1 CHADD0
CONTROL REGISTER 1 ADDRESS
RADD4
ADC CHANNEL ADDRESS
RADD3
RADD2
RADD1
5-BIT READ REGISTER ADDRESS
OPERATING
MODE
03796-024
NORMAL (SINGLE-ENDED)/
RATIOMETRIC (DIFFERENTIAL)
CONVERSION
Figure 46. Designation of Data-Word Bits in AD7877 Write Operations
CS
1
16
1
16
DCLK
0000 + 12-BIT DATA3
0000 + 12-BIT DATA3
HIGH-Z
D15
DOUT1
D0
HIGH-Z
D15
REGISTER n DATA4
D0
REGISTER n + 1 DATA4
4-BIT ADDRESS + 12-BIT DATA
D15
D0
NOTES:
1DATA IS CLOCKED OUT ON THE FALLING EDGE OF DCLK.
2INPUT DATA IS SAMPLED ON THE RISING EDGE OF DCLK.
3FOR 8-BIT REGISTERS, 8 LEADING ZEROS PRECEDE 8 BITS OF DATA.
4REGISTER READ ADDRESS INCREMENTS AUTOMATICALLY, PROVIDED THAT A NEW ADDRESS IS NOT WRITTEN TO CONTROL REGISTER 1.
Figure 47. Overall Read/Write Timing
Rev. E | Page 28 of 45
03796-025
DIN2
Data Sheet
AD7877
WRITE TIMING
No serial interface operations can take place when CS is high.
To write to the AD7877, CS must be taken low. To write to the
device, a burst of 16 clock pulses is input to DCLK while the write
data is input to DIN. Data is clocked in on the rising edge of
DCLK. If multiple write operations are to be performed, CS must
be taken high after the end of each write operation before another
write operation can be performed by taking CS low again.
READING DATA
Data is available on the DOUT pin following the falling edge of
CS, when the device is being clocked. The MSB is clocked out
on the falling edge of CS, with subsequent data bits clocked out
on the falling edge of DCLK.
After CS is taken low and the device is clocked, the AD7877
outputs data from the register whose read address is currently
stored in Control Register 1. Once this data has been output,
the address increments automatically. CS must be taken high
between reads. When CS is taken low again, reading continues
from the register whose read address is in Control Register 1,
provided that a write operation does not change the address. If
the register read address reaches 11111b, it is then reset to zero.
This feature allows all registers to be read out in sequence without having to explicitly write all their addresses to the device.
Note that because data-words are 16 bits long, but the data
registers are only 12 bits long, or 8 bits in the case of GPIO
registers, the first four bits of a readback data-word are zeros, or
the first 8 bits in the case of a GPIO register.
VDRIVE PIN
The supply voltage to all pins associated with the serial interface
(DAV, DIN, DOUT, DCLK, CS, PENIRQ, and ALERT) is
separate from the main VCC supply and is connected to the
VDRIVE pin. This allows the AD7877 to be connected directly to
processors whose supply voltage is less than the minimum
operating voltage of the AD7877, in fact, as low as 1.7 V.
Rev. E | Page 29 of 45
AD7877
Data Sheet
GENERAL-PURPOSE I/O PINS
The AD7877 has one dedicated general-purpose logic input/
output pin (GPIO4), and any or all of the three auxiliary analog
inputs can also be reconfigured as GPIOs. Associated with the
GPIOs are two 8-bit control registers and one 8-bit data register
that are accessed using the extended write mode.
As described in the Reading Data section, GPIO registers are
written to using the extended writing mode. The first four bits
of the data-word must be 1111b to access the extended writing
map, and the next four bits are the GPIO register address. This
leaves 8 bits for the GPIO register data, because all GPIO
registers are 8 bits.
The GPIO control registers are located at the 0000b and 0001b
extended writing map addresses, and the GPIO data register is
at Address 0010b. GPIO registers are read in the same way as
other registers, by writing a 5-bit address to Control Register 1.
The GPIO registers are located at Read Addresses 11011b to
Read Address 11101b.
If POL = 1 and DIR = 0, a 1 in the GPIO data register bit puts a
1 on the corresponding GPIO output pin. A 0 in the GPIO data
register bit puts a 0 on the GPIO output pin.
If POL = 0 and DIR = 1, a 1 at the input pin sets the corresponding GPIO data bit to 0. A 0 at the input pin clears the
corresponding GPIO data bit to 1.
If POL = 0 and DIR = 0, a 1 in the GPIO data register bit puts a
0 on the corresponding GPIO output pin. A 0 in the GPIO data
register bit puts a 1 on the GPIO output pin.
ALERT Enable (ALEN)
GPIOs can operate as interrupt sources to trigger the ALERT
output. This is controlled by the ALERT enable (ALEN) bits in
the GPIO configuration registers. When ALEN = 1, the corresponding GPIO can trigger an ALERT. When ALEN = 0, the
corresponding GPIO cannot cause the ALERT output to assert.
Each GPIO pin is configured by four bits in one of the GPIO
control registers and has a data bit in the GPIO data register.
The GPIO configuration bits are described in the following
sections and in Table 12. Also see the Detailed Register
Descriptions section.
ALERT is asserted low if any GPIO data register bit is set when
the GPIO is configured as an input. The GPIO data bit is set if a
1 appears on the GPIO input pin when POL = 1, or if a 0
appears on the GPIO input pin when POL = 0. ALERT is
triggered only when the GPIO is configured as an input, that is,
when DIR = 1. ALERT can never be triggered by a GPIO that is
configured as an output, that is, DIR = 0.
Enable (EN)
ALERT Output
These bits enable or disable the GPIO pins. When EN = 0, the
corresponding GPIO pin is configured as the alternate function
(AUX input). The other GPIO configuration bits have no effect,
if the particular GPIO is not enabled. When EN = 1, the pin is
configured as a GPIO pin. GPIO4, which does not have an
alternate function, does not have an EN bit; it is always enabled.
The ALERT pin is an alarm or interrupt output that goes low if
any one of a number of interrupt sources is asserted. The results
of high and low limit comparisons on the AUX1, BAT1, BAT2,
and TEMP1 channels are interrupt sources. An out-of-limit
comparison sets a status bit in the alert status/mask register
(Address 00011b).There are separate status bits for both the
high and low limits on each channel to indicate which limit was
exceeded. The interrupt sources can be masked out by clearing
the corresponding enable bit in this register. There is one enable
bit per channel.
GPIO CONFIGURATION
Direction—DIR
These bits set the direction of the GPIO pins. When DIR = 0,
the pin is an output. Setting or clearing the relevant bit in the
GPIO data register outputs a value on the corresponding GPIO
pin. The output value depends on the POL bit.
When DIR = 1, the pin is an input. An input value on the
relevant GPIO pin sets or clears the corresponding bit in the
GPIO data register, depending on the POL bit. A GPIO data
register bit is read-only when DIR = 1 for that GPIO.
Polarity (POL)
When POL = 0, the GPIO pin is active low. When POL = 1, the
GPIO pin is active high. How this bit affects the GPIO operation also depends on the DIR bit.
ALERT is also asserted if an input on a GPIO pin sets a bit in
the GPIO data register, as explained in the ALERT Enable
(ALEN) section. GPIO interrupts can be disabled by clearing
the corresponding ALEN bit in the GPIO control registers.
The interrupt source can be identified by reading the GPIO data
register and the alert status/enable register. ALERT remains
asserted until the source of the interrupt has been masked out
or removed.
If POL = 1 and DIR = 1, a 1 at the input pin sets the corresponding GPIO data register bit to 1. A 0 at the input pin clears
the corresponding GPIO data bit to 0.
Rev. E | Page 30 of 45
Data Sheet
AD7877
If the ALERT source is a GPIO, then masking out the interrupt
by clearing the corresponding ALEN bit to 0 or removing the
source of the interrupt on the GPIO pin causes ALERT to go
high again.
If the ALERT source is an out-of-limit measurement, writing a
0 to the corresponding status bit in the alert status/enable
register causes ALERT to go high. However, the status bit is set
to 1 again on the next measurement cycle, if the measurement
remains out of limit. The ALERT source can also be masked by
clearing the relevant bit in the alert status/enable register to 0.
Table 12. GPIO Configuration
EN
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
DIR
X
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
POL
X
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
ALEN
X
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
Data Bit
X
0
1
0
1
0
1
0
1
12
02
12
02
02
12
02
12
Pin Voltage
X
11
01
11
01
01
11
01
11
0
1
0
1
0
1
0
1
ALERT
X
1
1
1
1
1
1
1
1
1
1
0
1
1
1
1
0
A change in the data register causes a change in the output voltage on the pin.
A change in input voltage on the pin causes a change in the data register bit.
Rev. E | Page 31 of 45
AD7877
Data Sheet
GROUNDING AND LAYOUT
The bottom of the chip scale package has a central thermal pad.
The thermal pad on the printed circuit board should be at least
as large as this exposed pad. On the printed circuit board, provide a
clearance of at least 0.25 mm between the thermal pad and the
inner edges of the pad pattern to ensure that shorting is avoided.
It is recommended that the ground pins, AGND and DGND, be
shorted together as close as possible to the device itself on the
user’s PCB.
For more information on grounding and layout considerations
for the AD7877, refer to the AN-577 Application Note, Layout
and Grounding Recommendations for Touch Screen Digitizers.
Using thermal vias on the printed circuit board thermal pad
improves the thermal performance of the package. If vias are
used, incorporate them in the thermal pad at a 1.2 mm pitch
grid. Keep the via diameter between 0.3 mm and 0.33 mm. The
via barrel should be plated with 1 oz. copper to plug the via.
PCB DESIGN GUIDELINES FOR CHIP SCALE
PACKAGES
The lands on the chip scale package (CP-32) are rectangular.
The printed circuit board pad for these should be 0.1 mm
longer than the package land length and 0.05 mm wider than
the package land width. To ensure that the solder joint size is
maximized, center the land on the pad.
The user should connect the printed circuit board thermal pad
to AGND.
TO LCD
BACKLIGHT
VIN
OUT
FB
DC-DC
CONVERTER
RRNG
25
ARNG
DOUT
DCLK
NC
1
NC
2
BAT2
NC 24
3
BAT1
4
AUX3/GPIO3
5
AUX2/GPIO2
STOPACQ 20
MISO
6
AUX1/GPIO1
DIN 19
MOSI
7
VCC
8
NC
HOST
DAV 23
INT1
ALERT 22
AD7877
GPIO4
21
INT2
GPIO
DGND
9
10
11
12
13
14
15
PENIRQ
17
SCLK
CS
PENIRQ
NC
AGND
CS 18
Y+
1.0F–10F
(OPTIONAL)
26
X+
16
HSYNC SIGNAL
FROM LCD
NC = NO CONNECT
TOUCH
SCREEN
Figure 48. Typical Application Circuit
Rev. E | Page 32 of 45
03796-026
TEMPERATURE
MEASUREMENT
DIODE
27
Y–
MAIN
BATTERY
0.1F
28
X–
VOLTAGE
REGULATOR
29
SPI
INTERFACE
FROM AUDIO
REMOTE CONTROL
FROM
HOTSYNC INPUTS
30
NC
SECONDARY
BATTERY
31
VDRIVE
NC
32
VREF
0.1F
AOUT
VCC
Data Sheet
AD7877
REGISTER MAPS
Table 13. Write Register Map
WADD3
0
0
Register Address
Binary
WADD2 WADD1 WADD0
0
0
0
0
0
1
Hex
0
1
Register Name
None
Control Register 1
0
0
1
0
2
Control Register 2
0
0
1
1
3
0
0
0
0
1
1
1
1
1
1
1
1
1
0
0
0
0
1
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
4
5
6
7
8
9
A
B
C
1
1
0
1
D
1
1
1
1
1
1
0
1
E
F
Alert
status/enable
register
AUX1 high limit
AUX1 low limit
BAT1 high limit
BAT1 low limit
BAT2 high limit
BAT2 low limit
TEMP1 low limit
TEMP1 high limit
Sequencer
Register 0
Sequencer
Register 1
DAC register
Extended write
Description
Unused; writing to this address has no effect
Contains ADC channel address, register read address, and ADC
mode
Contains ADC averaging, acquisition time, power management,
first conversion delay, STOPACQ polarity, and reference and timer
settings
Contains status of high/low limit comparisons for TEMP1, BAT1,
BAT2, and AUX1, and enable bits to allow these channels to
become interrupt sources
User-programmable AUX1 upper limit
User-programmable AUX1 lower limit
User-programmable BAT1 upper limit
User-programmable BAT1 lower limit
User-programmable BAT2 upper limit
User-programmable BAT2 lower limit
User-programmable TEMP1 lower limit
User-programmable TEMP1 upper limit
Contains channel selection data for slave mode (software)
sequencing
Contains channel selection data for master mode (hardware)
sequencing
Contains DAC data and setup information
Not a physical register; enables writing to extended writing map
Table 14. Extended Writing Map
EADD3
0
Register Address
Binary
EADD2 EADD1 EADD0
0
0
0
Hex
0
0
0
0
1
1
0
0
1
0
2
Register Name
GPIO Control
Register 1
GPIO Control
Register 2
GPIO data
Description
Contains polarity, direction, enabling, and interrupt enabling
settings for GPIO1 and GPIO2
Contains polarity, direction, enabling, and interrupt enabling
settings for GPIO3 and GPIO4
Contains GPIO1 to GPIO4 data
Rev. E | Page 33 of 45
AD7877
Data Sheet
Table 15. Read Register Map
RADD4
0
0
0
0
RADD3
0
0
0
0
Register Address
Binary
RADD2 RADD1
0
0
0
0
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
Register Name
None
Control Register 1
Control Register 2
Alert status/enable
register
AUX1 high limit
AUX1 low limit
BAT1 high limit
BAT1 low limit
BAT2 high limit
BAT2 low limit
TEMP1 low limit
TEMP1 high limit
Sequencer Register 0
Sequencer Register 1
DAC register
None
X+
Y+
Y− (Z2)
1
1
1
1
1
1
1
1
0
0
0
0
0
1
1
1
0
1
1
1
1
0
0
0
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
13
14
15
16
17
18
19
1A
AUX1
AUX2
AUX3
BAT1
BAT2
TEMP1
TEMP2
X+ (Z1)
1
1
0
1
1
1B
1
1
1
0
0
1C
1
1
1
1
1
1
1
1
1
0
1
1
1
0
1
1D
1E
1F
GPIO Control
Register 1
GPIO Control
Register 2
GPIO data
None
None
RADD0
0
1
0
1
Hex
00
01
02
03
Rev. E | Page 34 of 45
Description
Reads back all zeros
See Table 13
See Table 13
See Table 13
See Table 13
See Table 13
See Table 13
See Table 13
See Table 13
See Table 13
See Table 13
See Table 13
See Table 13
See Table 13
See Table 13
Factory use only
Measurement at X+ input for Y position
Measurement at Y+ input for X position
Measurement at Y− input for touch-pressure
calculation Z2
Auxiliary Input 1 measurement
Auxiliary Input 2 measurement
Auxiliary Input 3 measurement
Battery Input 1 measurement
Battery Input 2 measurement
Single-ended temperature measurement
Differential temperature measurement
Measurement at X+ input for touch-pressure
calculation Z1
See Table 14
See Table 14
See Table 14
Factory use only
Factory use only
Data Sheet
AD7877
DETAILED REGISTER DESCRIPTIONS
Register Name: Control Register 1
Write Address:
0001
Read Address:
00001
Default Value:
0x000
Type:
Read/write
Table 16.
Bit
0
1
Name
MODE0
MODE1
Read/Write
R/W
R/W
2
3
4
5
6
7
8
9
10
RD0
RD1
RD2
RD3
RD4
CHADD0
CHADD1
CHADD2
CHADD3
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
11
SER/DFR
R/W
Description
LSB of ADC mode code
MSB of ADC mode code
00 = no conversion
01 = single conversion
10 = conversion sequence (slave mode)
11 = conversion sequence (master mode)
LSB of register read address; to read a register, its address must first be written to Control Register 1
Bit 1 of register read address; to read a register, its address must first be written to Control Register 1
Bit 2 of register read address; to read a register, its address must first be written to Control Register 1
Bit 3 of register read address; to read a register, its address must first be written to Control Register 1
MSB of register read address; to read a register, its address must first be written to Control Register 1
LSB of ADC channel address
Bit 1 of ADC channel address
Bit 2 of ADC channel address
MSB of ADC channel address
0000 = X+ input (Y position)
0001 = Y+ input (X position)
0010 = Y− (Z2) input (used for touch-pressure calculation)
0011 = Auxiliary Input 1 (AUX1)
0100 = Auxiliary Input 2 (AUX2)
0101 = Auxiliary Input 3 (AUX3)
0110 = Battery Monitor Input 1 (BAT1)
0111 = Battery Monitor Input 2 (BAT2)
1000 = Temperature Measurement 1 (used for single conversion)
1001 = Temperature Measurement 2 (used for differential measurement method)
1010 = X+ (Z1) input (used for touch-pressure calculation)
Selects normal (single-ended) or ratiometric (differential) conversion
0 = ratiometric (differential)
1 = normal (single-ended)
Rev. E | Page 35 of 45
AD7877
Data Sheet
Register Name: Control Register 2
Write Address:
0010
Read Address:
00010
Default Value:
0x000
Type:
Read/write
Table 17.
Bit
0
1
Name
TMR0
TMR1
Read/Write
R/W
R/W
2
REF
R/W
3
POL
R/W
4
5
FCD0
FCD1
R/W
R/W
6
7
PM0
PM1
R/W
R/W
8
9
ACQ0
ACQ1
R/W
R/W
10
11
AVG0
AVG1
R/W
R/W
Description
LSB of conversion interval timer
MSB of conversion interval timer
00 = convert only once
01 = every 1024 clock periods (512 µs)
10 = every 2048 clock periods (1.024 ms)
11 = every 16,384 clock periods (8.19 ms)
Selects internal or external reference
0 = internal reference
1 = external reference
Indicates polarity of signal on STOPACQ pin
0 = active low
1 = active high
LSB of first conversion delay
MSB of first conversion delay
This delay occurs before the first conversion after powering up the ADC, before converting the X and Y
coordinate channels to allow settling, and after the last conversion to allow PENIRQ precharge
00 = 1 clock period delay (500 ns)
01 = 256 clock periods delay (128 µs)
10 = 2048 clock periods delay (1.024 ms)
11 = 16,384 clock periods delay (8.19 ms)
LSB of ADC power management code
MSB of ADC power management code
00 = ADC and reference powered down continuously
For the following codes, regardless of PM bits, the reference is always powered down if the REF bit is 1:
01 = ADC and reference powered down when not converting
10 = ADC and reference powered up continuously (master sequencer does not work if PM = 10)
11 = ADC powered down when not converting, reference powered up
LSB of ADC acquisition time
MSB of ADC acquisition time
00 = 4 clock periods (2 µs)
01 = 8 clock periods (4 µs)
10 = 16 clock periods (8 µs)
11 = 32 clock periods (16 µs)
LSB of ADC averaging code
MSB of ADC averaging code
00 = no averaging (1 conversion per channel)
01 = 4 measurements per channel averaged
10 = 8 measurements per channel averaged
11 = 16 measurements per channel averaged
Rev. E | Page 36 of 45
Data Sheet
AD7877
Register Name: Alert Status/Enable Register
Write Address:
0011
Read Address:
00011
Default Value:
0x000
Type:
Read/write
Table 18.
Bit
0
1
2
3
4
5
6
7
Name
AUX1LO
BAT1LO
BAT2LO
TEMP1LO
AUX1HI
BAT1HI
BAT2HI
TEMP1HI
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Description
When this bit is 1, the AUX1 channel is below its low limit
When this bit is 1, the BAT1 channel is below its low limit
When this bit is 1, the BAT2 channel is below its low limit
When this bit is 1, the TEMP1 channel is above its low limit
When this bit is 1, the AUX1 channel is above its high limit
When this bit is 1, the BAT1 channel is above its high limit
When this bit is 1, the BAT2 channel is above its high limit
When this bit is 1, the TEMP1 channel is below its high limit
8
AUX1EN
R/W
Setting this bit enables AUX1 as an interrupt source to the ALERT output
9
BAT1EN
R/W
Setting this bit enables BAT1 as an interrupt source to the ALERT output
10
BAT2EN
R/W
Setting this bit enables BAT2 as an interrupt source to the ALERT output
11
TEMP1EN
R/W
Setting this bit enables TEMP1 as an interrupt source to the ALERT output
Register Name: AUX1 High Limit
Register Name: BAT1 Low Limit
Write Address:
0100
Write Address:
0111
Read Address:
00100
Read Address:
00111
Default Value:
0x000
Default Value:
0x000
Type:
Read/write
Type:
Read/write
This register contains the 12-bit high limit for Auxiliary Input 1.
Register Name: AUX1 Low Limit
Write Address:
0101
Read Address:
00101
Default Value:
0x000
Type:
Read/write
This register contains the 12-bit low limit for Battery
Monitoring Input 1.
Register Name: BAT2 High Limit
Write Address:
1000
Read Address:
01000
Default Value:
0x000
This register contains the 12-bit low limit for Auxiliary Input 1.
Type:
Read/write
Register Name: BAT1 High Limit
This register contains the 12-bit high limit for Battery
Monitoring Input 2.
Write Address:
0110
Read Address:
00110
Default Value:
0x000
Type:
Read/write
This register contains the 12-bit high limit for Battery
Monitoring Input 1.
Rev. E | Page 37 of 45
AD7877
Data Sheet
Register Name: BAT2 Low Limit
Register Name: TEMP1 High Limit
Write Address:
1001
Write Address:
1011
Read Address:
01001
Read Address:
01011
Default Value:
0x000
Default Value:
0x000
Type:
Read/write
Type:
Read/write
This register contains the 12-bit low limit for Battery
Monitoring Input 2.
This register contains the 12-bit high limit for temperature
measurement.
Register Name: TEMP1 Low Limit
Write Address:
1010
Read Address:
01010
Default Value:
0x000
Type:
Read/write
This register contains the 12-bit low limit for temperature
measurement.
Rev. E | Page 38 of 45
Data Sheet
AD7877
Register Name: Sequencer Register 0
Write Address:
1100
Read Address:
01100
Default Value:
0x000
Type:
Read/write
Table 19.
Bit
0
1
2
Name
Not Used
Z1_SS
TEMP2_SS
Read/Write
R/W
R/W
R/W
3
TEMP1_SS
R/W
4
5
6
7
8
9
10
11
BAT2_SS
BAT1_SS
AUX3_SS
AUX2_SS
AUX1_SS
Z2_SS
XPOS_SS
YPOS_SS
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Description
This bit is not used
Setting this bit includes the Z1 touch-pressure measurement (X+ input) in a slave mode sequence
Setting this bit includes a temperature measurement using differential conversion in a slave mode
sequence
Setting this bit includes a temperature measurement using single-ended conversion in a slave mode
sequence
Setting this bit includes measurement of Battery Monitor Input 2 in a slave mode sequence
Setting this bit includes measurement of Battery Monitor Input 1 in a slave mode sequence
Setting this bit includes measurement of Auxiliary Input 3 in a slave mode sequence
Setting this bit includes measurement of Auxiliary Input 2 in a slave mode sequence
Setting this bit includes measurement of Auxiliary Input 1 in a slave mode sequence
Setting this bit includes the Z2 touch-pressure measurement (Y− input) in a slave mode sequence
Setting this bit includes measurement of the X position (Y+ input) in a slave mode sequence
Setting this bit includes measurement of the Y position (X+ input) in a slave mode sequence
Register Name: Sequencer Register 1
Write Address:
1101
Read Address:
01101
Default Value:
0x000
Type:
Read/write
Table 20.
Bit
0
1
2
Name
Not Used
Z1_MS
TEMP2_MS
Read/Write
R/W
R/W
R/W
3
TEMP1_MS
R/W
4
5
6
7
8
9
10
11
BAT2_MS
BAT1_MS
AUX3_MS
AUX2_MS
AUX1_MS
Z2_MS
XPOS_MS
YPOS_MS
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Description
This bit is not used
Setting this bit includes the Z1 touch-pressure measurement (X+ input) in a master mode sequence
Setting this bit includes a temperature measurement using differential conversion in a master mode
sequence
Setting this bit includes a temperature measurement using single-ended conversion in a master mode
sequence
Setting this bit includes measurement of Battery Monitor Input 2 in a master mode sequence
Setting this bit includes measurement of Battery Monitor Input 1 in a master mode sequence
Setting this bit includes measurement of Auxiliary Input 3 in a master mode sequence
Setting this bit includes measurement of Auxiliary Input 2 in a master mode sequence
Setting this bit includes measurement of Auxiliary Input 1 in a master mode sequence
Setting this bit includes the Z2 touch-pressure measurement (Y− input) in a master mode sequence
Setting this bit includes measurement of the X position (Y+ input) in a master mode sequence
Setting this bit includes measurement of the Y position (X+ input) in a master mode sequence
Rev. E | Page 39 of 45
AD7877
Data Sheet
Register Name: DAC Register
Write Address:
1110
Read Address:
01110
Default Value:
0x008
Type:
Read/write
Table 21.
Bit
0
Name
RANGE
Read/Write
R/W
1
2
Not Used
V/I
R/W
R/W
3
PD
R/W
4
5
6
7
8
9
10
11
DAC0
DAC1
DAC2
DAC3
DAC4
DAC5
DAC6
DAC7
Description
Output range of the DAC in voltage mode
0 = 0 to VCC/2
1 = 0 to VCC
This bit is not used
Voltage output and current output
0 = voltage
1 = current
DAC power-down
0 = DAC on
1 = DAC powered down
LSB of DAC data
Bit 1 of DAC data
Bit 2 of DAC data
Bit 3 of DAC data
Bit 4 of DAC data
Bit 5 of DAC data
Bit 6 of DAC data
MSB of DAC data
Register Name: Y Position
Register Name: Z2
Write Address:
N/A
Write Address:
N/A
Read Address:
10000
Read Address:
10010
Default Value:
0x000
Default Value:
0x000
Type:
Read only
Type:
Read only
This register contains the 12-bit result of the measurement at
the X+ input with Y layer excited (Y position measurement).
Register Name: X Position
Write Address:
N/A
Read Address:
10001
Default Value:
0x000
Type:
Read only
This register contains the 12-bit result of the measurement at
the Y− input with excitation voltage applied to Y+ and X− (used
for touch-pressure calculation).
Register Name: AUX1
This register contains the 12-bit result of the measurement at
the Y+ input with X layer excited (X position measurement).
Write Address:
N/A
Read Address:
10011
Default Value:
0x000
Type:
Read only
This register contains the 12-bit result of the measurement at
Auxiliary Input 1.
Rev. E | Page 40 of 45
Data Sheet
AD7877
Register Name: AUX2
Register Name: TEMP1
Write Address:
N/A
Write Address:
N/A
Read Address:
10100
Read Address:
11000
Default Value:
0x000
Default Value:
0x000
Type:
Read only
Type:
Read only
This register contains the 12-bit result of the measurement at
Auxiliary Input 2.
This register contains the 12-bit result of a temperature
measurement using single-ended conversion.
Register Name: AUX3
Register Name: TEMP2
Write Address:
N/A
Write Address:
N/A
Read Address:
10101
Read Address:
11001
Default Value:
0x000
Default Value:
0x000
Type:
Read only
Type:
Read only
This register contains the 12-bit result of the measurement at
Auxiliary Input 3.
This register contains the 12-bit result of a temperature
measurement using a differential conversion.
Register Name: BAT1
Register Name: Z1
Write Address:
N/A
Write Address:
N/A
Read Address:
10110
Read Address:
11010
Default Value:
0x000
Default Value:
0x000
Type:
Read only
Type:
Read only
This register contains the 12-bit result of the measurement at
Battery Monitor Input 1.
Register Name: BAT2
Write Address:
N/A
Read Address:
10111
Default Value:
0x000
Type:
Read only
This register contains the 12-bit result of a measurement at the
X+ input with excitation voltage applied to Y+ and X− (used for
touch-pressure calculation).
This register contains the 12-bit result of the measurement at
Battery Monitor Input 2.
Rev. E | Page 41 of 45
AD7877
Data Sheet
GPIO REGISTERS
GPIO registers are written to using an extended 8-bit address.
The first four bits of the data-word are always 1111b to access
the extended writing map. The next four bits are the register
address. This leaves 8 bits for the GPIO data.
GPIO registers are read like all other registers, by writing a 5-bit
address to Control Register 1, then reading DOUT.
See the GPIO Configuration section for information on
configuring the GPIOs.
Register Name: GPIO Control Register 1
Write Address:
[1111] 0000
Read Address:
11011
Default Value:
0x000
Type:
Read/write
Table 22.
Bit
Name
Read/Write
Description
0
GPIO2_ALEN
R/W
If this bit is 1, GPIO2 is an interrupt source for the ALERT output; clearing this bit masks out GPIO2
as an interrupt source for the ALERT output
1
GPIO2_DIR
R/W
2
GPIO2_POL
R/W
3
GPIO2_EN
R/W
4
GPIO1_ALEN
R/W
This bit sets the direction of GPIO2
0 = output
1 = input
This bit determines if GPIO2 is active high or low
0 = active low
1 = active high
This bit selects the function of AUX2/GPIO2
0 = AUX2
1 = GPIO2
If this bit is 1, GPIO1 is an interrupt source for the ALERT output; clearing this bit masks out GPIO1
as an interrupt source for the ALERT output
5
GPIO1_DIR
R/W
6
GPIO1_POL
R/W
7
GPIO1_EN
R/W
This bit sets the direction of GPIO1
0 = output
1 = input
This bit determines if GPIO1 is active high or low
0 = active low
1 = active high
This bit selects the function of AUX1/GPIO1
0 = AUX1
1 = GPIO1
Rev. E | Page 42 of 45
Data Sheet
AD7877
Register Name: GPIO Control Register 2
Write Address:
[1111] 0001
Read Address:
11100
Default Value:
0x000
Type:
Read/write
Table 23.
Bit
Name
Read/Write
Description
0
GPIO4_ALEN
R/W
If this bit is 1, GPIO4 is an interrupt source for the ALERT output; clearing this bit masks out GPIO3
as an interrupt source for the ALERT output
1
GPIO4_DIR
R/W
2
GPIO4_POL
R/W
3
Not Used
This bit sets the direction of GPIO4
0 = output
1 = input
This bit determines if GPIO4 is active high or low
0 = active low
1 = active high
This bit is not used
4
GPIO3_ALEN
R/W
If this bit is 1, GPIO3 is an interrupt source for the ALERT output; clearing this bit masks out GPIO4
as an interrupt source for the ALERT output
5
GPIO3_DIR
R/W
6
GPIO3_POL
R/W
7
GPIO3_EN
R/W
This bit sets the direction of GPIO3
0 = output
1 = input
This bit determines if GPIO3 is active high or low
0 = active low
1 = active high
This bit selects the function of AUX3/GPIO3
0 = AUX3
1 = GPIO3
Register Name: GPIO Data Register
Write Address:
[1111] 0010
Read Address:
11101
Default Value:
0x000
Type:
Read/write
Table 24.
Bit
0
1
2
3
4
5
6
7
Name
Not used
Not used
Not used
Not used
GPIO4_DAT
GPIO3_DAT
GPIO2_DAT
GPIO1_DAT
Read/Write
R/W
R/W
R/W
R/W
Description
This bit is not used
This bit is not used
This bit is not used
This bit is not used
GPIO4 data bit
GPIO3 data bit
GPIO2 data bit
GPIO1 data bit
Rev. E | Page 43 of 45
AD7877
Data Sheet
OUTLINE DIMENSIONS
5.10
5.00 SQ
4.90
0.60 MAX
0.60 MAX
25
32
24
0.50
BSC
3.25
3.10 SQ
2.95
EXPOSED
PAD
17
12° MAX
1.00
0.85
0.80
SEATING
PLANE
0.80 MAX
0.65 TYP
8
16
0.50
0.40
0.30
TOP VIEW
9
BOTTOM VIEW
0.25 MIN
3.50 REF
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
0.30
0.25
0.18
PIN 1
INDICATOR
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2
Figure 49. 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
5 mm × 5 mm Body, Very Thin Quad
(CP-32-2)
Dimensions shown in millimeters
0.30
0.25
0.18
32
25
1
24
0.50
BSC
TOP VIEW
0.80
0.75
0.70
SEATING
PLANE
3.25
3.10 SQ
2.95
EXPOSED
PAD
8
17
0.50
0.40
0.30
16
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
9
BOTTOM VIEW
0.25 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WHHD.
Figure 50. 32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
5 mm x 5 mm Body, Very Very Thin Quad
(CP-32-7)
Dimensions shown in millimeters
Rev. E | Page 44 of 45
PIN 1
INDICATOR
112408-A
PIN 1
INDICATOR
5.10
5.00 SQ
4.90
10-02-2013-A
4.75
BSC SQ
PIN 1
INDICATOR
1
Data Sheet
AD7877
2.825
2.765
2.705
5
4
3
2
1
A
BALL A1
IDENTIFIER
2.605
2.545
2.485
B
2.00
REF
C
D
E
0.50
BSC
TOP VIEW
BOTTOM VIEW
(BALL SIDE DOWN)
SEATING
PLANE
(BALL SIDE UP)
SIDE VIEW
COPLANARITY
0.05
0.360
0.320
0.280
0.280
0.240
0.200
10-31-2012-A
0.650
0.590
0.530
0.240
0.220
0.200
Figure 51. 25-Ball Wafer Level Chip Scale Package [WLCSP]
2.5 mm × 2.8 mm Body
(CB-25-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1, 2
AD7877ACPZ-REEL
AD7877ACPZ-REEL7
AD7877ACPZ-500RL7
AD7877ACBZ-REEL
AD7877ACBZ-REEL7
AD7877WACPZ-REEL7
EVAL-AD7877EBZ
1
2
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
32-Lead LFCSP_VQ
32-Lead LFCSP_VQ
32-Lead LFCSP_VQ
25-Ball WLCSP
25-Ball WLCSP
32-Lead LFCSP_WQ
Evaluation Board
Package Option
CP-32-2
CP-32-2
CP-32-2
CB-25-1
CB-25-1
CP-32-7
Z = RoHS Compliant Part.
W = Qualified for Automotive Applications
AUTOMOTIVE PRODUCTS
The AD7877WACPZ models are available with controlled manufacturing to support the quality and reliability requirements of automotive
applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers
should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in
automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to
obtain the specific Automotive Reliability reports for these models.
©2004–2014 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D03796-0-12/14(E)
Rev. E | Page 45 of 45
Similar pages